悟空小侠传奇花果山灯饰安装说明书
Goku legend Huaguoshan lighting
installation instructions
悟空小侠传奇花果山灯饰安装说明书
Goku legend Huaguoshan lighting
installation instructions
四条灯光如下
A
B
C
D
3
1
2
将积木拆成 部分
Four lights as follows
Break the building blocks into parts
1 3
1 3
打开A包灯组,测试灯光
来到第 部分将第一颗灯珠安装在所示位置
→
Turn on A pack and test the lights
Come to Part and install the first bead in the position shown 1
1
安装完成如下
接下来将绿色积木拆起
→
Installation completed as follows
Next, the green building blocks
将导线穿过积木后还原
Restore the wire through the building block
→
将下一个灯组安装在箭头位置
安装完成如下
Install the next light set in the arrow position
Installation completed as follows
把箭头所示积木拆起如下
→
→
Remove the building blocks shown by the arrow
将最后一个灯珠安装在透明积木上
将导线藏在积木内并与还原
Install the last bead on the transparent building block
The wires are hidden in the building blocks and restored
打开B包灯组,测试灯光
来到 部分积木,将所示零件拆起 2
→
→
Turn on B pack and test the lights
Come to blocks and remove the parts shown 2
拆下后将两个灯组分别安装在图中两侧
→
→
安装完成如下,把接下去的导线穿到后面
→
Remove and install the two light groups on both sides
of the diagram
The installation is complete as follows. Put the next wire
through the back
把拆起的零件还原如图
将积木翻转到后面,将下图零件拆起
→
Restore the removed parts as shown
Flip the building blocks back and remove the following parts
拆起后把灯组安装在积木上如下
将剩下的导线藏在积木内并还原
Remove and install the lamp set on the building block as follows
Hide the remaining wires in the building blocks and restore them
将剩下的导线穿到顶部,把所示零件拆起
拆起后将导线穿过零件把灯珠安装在1x2零件内
→
→
Put the remaining wires through the top and remove the parts
shown
After removing the wire through the part, install the lamp bead
in x2 1 part
还原零件位置
将下一个灯珠安装在叶子上如下
Reduction part location
Install the next bead on the leaf as follows
将最后一个灯组安装在下图所示位置
→
安装完成如下
Install the last light set in the position shown below
Installation completed as follows
打开C包,测试灯光
将积木翻转到正面,把下图零件拆起
→
→
→
Turn on the C bag and test the lights
Flip the building blocks to the front and remove the following parts
拆下后将灯珠安装在透明零件内
将多余导线藏于积木内并还原零件
Install lamp beads in transparent parts after removal
Hide excess wires in building blocks and restore parts
将透明白零件拆下,将灯珠藏于零件内
还原零件
Remove the transparent white part and hide the lamp bead
inside the part
Reduction parts
将图中两个零件拿起
→
→
把箭头所指零件拆起
→
→
→
Pick up the two parts in the drawing
Remove the arrowhead
还原零件位置
将下图所示零件拆起
→
Reduction part location
Remove the parts shown below
零件拆下如下
将灯珠藏在透明白零件上,导线藏于零件内
Parts removed as follows
Hide the bead on the transparent white part and the wire
inside the part
拆起后将灯珠安装在所示位置将导线藏于零件内
还原零件
Install the lamp bead in the position shown and hide the wire in
the part
Reduction parts
→→
将箭头所指零件拆起
拆下如下
Remove the parts indicated by the arrow
Remove as follows
将灯珠和导线藏于零件内如下
将刚拿起的零件放还原位
Hide the lamp beads and inside the parts as follows
Return the parts you just picked up
打开D包,测试灯光
来到 部分积木,将第一个灯珠安装在下图所示 3
→
Turn on the D bag and test the lights
Come to the blocks and install the first lamp bead as shown below 3
安装完成如下
将1x6灯组安装在箭头所示位置
→
Installation completed as follows
Install x6 1 light set in the position shown in the arrow
安装完成如下
将下一个灯珠安装在箭头所示位置
→
Installation completed as follows
Install the next bead in the position indicated by the arrow
安装完成后将绿色零件拆起把导线藏于零件内
还原零件
Remove the green part and hide the wire inside the part after
installation
Reduction parts
将下一个零件安装在箭头所指位置
→
安装完成如下
Install the next part in the position indicated by the arrow
Installation completed as follows
将下图所指零件拆起
→
→
拆下如下
Remove the parts shown below
Remove as follows
将两个灯组安装在积木两侧如下
将导线藏于零件内并还原零件
Install two light groups on both sides of the building blocks
as follows
Hide the wire inside the part and restore the part
→
把导线穿过箭头所示位置
将最后一个灯珠安装如下
Pass the wire through the arrow
Install the last bead as follows