该页无缩略图
2019
飛球鎖业Fly.Globe
目录 Catalog
电子锁 EL6505ElectronicLock
01
02
03
分体智能锁 SplitIntelligentLock P7-11
断桥铝电子锁 Broken Bridge Aluminum Electronic Lock P12-13
刷卡+密码操作使用说明
InstructionsforSwipeCard+PasswordOperation
产品应用
ProductApplication
居民住宅/现代化办公室/学校/机关部门/写字楼 Residential housing/Modern office/School/Organ department/Office building
1、简介
针对住宅、办公室、智能小区的安全防范和现代化管理需求，我们推出了刷卡 ^ + 密码门锁模块。采用了先进的非接触式刷卡和密码作为开门钥匙，并且具有多种开门模式可供选择，更灵活、更方便、更安全！
Introduction
In view of the securityand modern management needs of residential, office and intelligent community,we have introduced themoduleof swipe card ^ + password door lock. It adopts advanced non-contact card swipe and password as the key to open the door, and has a variety of open modes to choose from.Itismore flexible,more conveniment and safer!
2.产品优势和特点
可以使用卡片和密码开门
用户的添加和删除采用基于区号的管理
■具有防旁人窥视密码功能所有元器件均采用国际知名品牌产品，质量稳定可靠门锁模块均经过防水、防潮、防霉处理
■门锁模块均经过高低温、振动、老化等测试，适应恶劣环境
Productadvantagesandcharacteristics
Usecardsand passwordsto open doors
Added and deleted usersaremanaged byareacode
Has the function of preventing others from peeping at the password
All components adopt internationally renowned brand products with
stableand reliable quality The door lock modules are waterproof, moisture-proof and mildew-proof
The door lock modules have been tested by high and low
temperature, vibrationand aging to adapt to harsh environment
| 电源供应 | 4.5V-6.5V（即4节干电池） |
| 典型静态电流 | |
| 工作电流 | |
| 开门卡片数量 | |
| 开门密码数量 | |
| 工作温度 | -10℃~60℃ |
| 相对湿度 | 20%~93% |
Technical parameters
| Power supply | 4.5V-6.5V(i.e.four section dry batteries) |
| Typical static current | |
| Working current | |
| Number of open-door cards | |
| Number of open-door passwords | |
| Working temperature | -10℃~60°℃ |
| Relative humidity | 20%~93% |
前板结构
1.外围尺寸包含硅胶垫注
2.\*限于某些型号(请确认购买产品型号及配置)
Front panel structure
1.Peripheral dimensions include silicone pads
2.Limited to certain models (please confirm the purchase model and configuration)
后板结构
Rear structure
| 序号 | 类别 | 项目 | 技术特征描述 |
| 1 | 开门方式 | *指纹开启 | 其中管理员3枚、普通用户97枚 |
| 2 | 密码开启 | 可注册3个管理员用户，7个普通用户 | |
| 3 | 卡开启 | 可注册3个管理员用户，47个普通用户 | |
| 4 | 机械钥匙 | 2把机械钥匙 | |
| 5 | 电源 | 工作电压 | 4节5#1.5VAA碱性电池 |
| 6 | 电池寿命 | 正常状态下使用超过10,000次 | |
| 7 | 报警电压 | ||
| 8 | 应急电源 | ≤4.8V | |
| 9 | 功耗 | 静态电流 | 5VMicro-USB |
| 10 | 动态电流 | ≤50uA | |
| 11 | 指纹采集头 | 采集面积 | ≤200mA Φ13 |
| 12 | 分辩率 | 508dpi | |
| 13 | 响应时间 | ||
| 14 | 工作温度 | -20摄氏度~60摄氏度 | |
| 15 | 相对湿度 | 20%~95% | |
| 16 | 拒真率（FRR） | ≤0.1% | |
| 17 | 认假率（FAR） | ≤0.001% | |
| 类型 | |||
| 18 | 对比方式 | 半导体 | |
| 19 | 1:N | ||
| 20 | 抗静电能力 开门记录 | 20条 | |
| 21 | 辅助功能 总重量 | 面板组件+锁体 | 约6Kgs（不同款式重量不同） |
| 22 | |||
| 23 | 执行标准 | GA701-2007、GB21556-2008 |
Maintechnicalparameters
| No. | Category | Item | Technical featuredescription |
| 1 | Openingmode | *Fingerprint opening | There are 3 administrators and 97 ordinary users |
| 2 | Password opening | Canregister3administrator users,7ordinaryusers | |
| 3 | Card opening | Can register 3 administrators users and 47 ordinary users | |
| 4 | Mechanical key | Two mechanical keys | |
| 5 | Power supply | Workingvoltage | Foursection5#1.5VAAalkaline batteries |
| 6 | Battery life | Use more than l0,ooo times under normal conditions | |
| 7 | Alarmvoltage | ≤4.8V | |
| 8 | Emergency supply | 5VMicro-USB | |
| Quiescent current | ≤50uA | ||
| 10 | Power waste | Dynamic current | ≤200mA |
| 11 | Collection area | 13 | |
| 12 | Resolution rate | 508dpi | |
| 13 | Response time | ||
| 14 | Working temperature | -20 to 60 degreesCelsius | |
| 15 *Fingerprint | Relative humidity | 20%~95% | |
| 16 | Refusal to Truth (FRR) | ≤0.1% | |
| 17 | Falserecognition rate (FAR) | ≤0.001% | |
| 18 | Type | Semiconductor | |
| 19 | Contrast mode | 1:N | |
| 20 | Antistatic ability | Lessthan15KVofair/8KVof exposure | |
| 21 | Auxiliary function | Opening record | 20 |
| 22 | Totalweight | Panel component+lock body | About 6Kgs(different style and different weight) |
| 23 | Executive standard | GA701-2007、GB21556-2008 |
安装爆炸图（适用5050锁体与单舌）
Installation of explosion diagram (suitable for5o50lock bodyand single latch)
| 序号 | 名称 | 数量 |
| A | 前板 | 1 |
| B | 螺柱 | 2 |
| C | 方铁 | 1 |
| D | 方铁弹簧 | 1 |
| E | 锁体（单舌） | 1 |
| F | 后底板组件（含硅胶） | 1 |
| J | M4*45竹节螺丝 | 2 |
| H | 后板 | 1 |
| I | M4*14螺丝 | 3 |
| J | 电池盖 | 1 |
| No. | Name | Qty. |
| A | Front plate | 1 |
| B | Screw colum | 2 |
| C | Square iron | 1 |
| D | Square iron spring | 1 |
| E | Lock body(single latch) | 1 |
| F | Real back plate assembly (containingsilica gel) | 1 |
| J | M4*45 slub screw | 2 |
| H | Rear plate | 1 |
| M4*14 screw | 3 | |
| J | Battery cover | 1 |
安装爆炸图6068锁体
Installationofexplosiondiagramfor6o68lockbody
安装锁体与单舌 Installationoflockbodyandsinglelatch
1.门孔请按照开孔纸规尺寸进行开孔
2.将锁体(单舌)安装到门上，并用螺丝将其固定
注：根据产品配置进行安装
1.Open the door according to the size of the opening paper gauge 2.Install the lock body (single house) on the door and fix it with screw Note:Install according to the product configuration
| 序号 | 名称 | 数量 |
| A | 前板 | 1 |
| B | 方颈螺丝 | 2 |
| C | 螺柱 | 3 |
| D | 方铁 | 1 |
| E | 方铁弹簧 | 1 |
| F | 6068锁体 | 1 |
| G | 后底板组件 （含硅胶） | 2 |
| H | M4*45竹节螺丝 | 3 |
| I | 后板 | 1 |
| J | M4*14螺丝 | 3 |
| K | 电池盖 | 1 |
| No. | Name | Qty. |
| A | Front plate | 1 |
| B | Square neck screw | 2 |
| C | Screwcolum | 3 |
| D | Square iron | 1 |
| E | Square iron spring | 1 |
| F | 6068Lock body | 1 |
| G | Real back plate assembly (containing silica gel) | 2 |
| H | M4*45 slub screw | 3 |
| I | Rear plate | 1 |
| J | M4*14 screw | 3 |
| K | Battery cover | 1 |
EL412
分体智能锁说明书
| 电源 | 3.7伏 |
| 典型动态电源 | 《3毫安 |
| 动作电流 | 《100毫安 |
| 指纹容差 | 《=100组 |
| 工作温度 | -20℃-60℃ |
| 工作环境湿度 | 5%-95% |
| 可用锁利 | 单锁利 |
| 充电时间 | 60分钟 |
| 电池寿命 | 1年（8000次） |
| 电池类型 | 磷酸铁锂电池 |
| 门板厚度 | 33~55mm(1-1/3"~2-3/16") |
| 把手方向 | 右或者左 |
Product Parameters
| Power supply | 3.7v |
| Typicaldynamiccurrent | 《3mA |
| Action current | 《100mA |
| Fingerprint capacity | 《=100 groups |
| Working temperature | -20c-60c |
| Working humidity | 5%-95% |
| Available latch | Single latch |
| Charge time | 60 minutes |
| Battery life | 1year(8000 times） |
| Battery type | Lithium iron phosphate battery |
| Door thicness | 33~55mm(1-1/3"~2-3/16") |
| Handle Direction | Right orLeft |
0 安装前需知
1.2出厂状态
1.1组件电量指示灯
·手指按压在指纹感应器，指纹锁会自动验证指纹。
·未登录指纹时，红蓝显示灯会同时亮，此时按任何指纹都可开锁。
登记
2.1登記指纹 (出厂状态)
·用设定针插入设定孔内，会听到两次短？哗”声，同时红蓝显示灯交替闪烁，代表进入登记状态。
·按压指纹进行登记，每枚指纹需录入三次才完成。完成后，红蓝显示灯会继续闪烁，可进行其他指纹登录。
●每次完成登录指纹，会听到一次长“哗”声。首三枚指纹为管理指纹，可用于解锁、登记其他指纹及删除指纹之确认。
注意：若没有任何操作，电子手把将于10秒后退出设定模式。
一般使用
3.1指纹解锁
·按压已登录的指纹，蓝色显示灯会亮起，同时会听到一次长“哗”声，转动把手即可开门。
·使用无效的指纹开锁会听到两次短“哗”声，连续五次错误，红蓝色显示灯会交替闪烁，并会连续发出多次短“哗”声。
3.2指纹登記 (添加其他用戶)
·用设置定针插入设定孔内，会听到两次短？哗”声，同时红蓝显示灯交替闪烁，代表进入登记状态。
·按压管理者指纹验证后，新用户按压指纹进行登录，每枚指纹需录入三次才完成。每次添加新用户指纹，必须使用管理者指纹确认。
取消
删除所有指纹
·用设置定针插入设定孔内按住5秒，会听到5次“哗”声及3次长“哗”声，蓝讯号显示灯会亮起。·按压管理指纹进行验证，会听到一次长“哗”声，所有已登录的指纹都会被删除。
充電方式
·当低电量时，按压指纹电量指示灯会亮起。
·插入电源时，中间的电源指示灯会亮起；充满后，指示灯会变暗，代表处于满电状态。
0
BeforeInstallation
1.1 Components
3.1Toopendoorwith fingerprints
Pressthe registered fingerprint,the blueLEDwill on,and you will hearalong"beep" sound, turn the lever to open the door.
Whenthe invalid fingerprint isused tounlock the doorand hear twoshort "beep"sounds Whentherearefiveconsecutiveerrors,theredandblueLEDswillflashalternatelyand will emitmultipleshort"beep".
1.2 Factory Setting
Pressthe finger on thesensor,thelever will automaticallyverify the fingerprint
●Whenthefingerprint isnotregistered,theredand blueLEDswill be onat the same time.At this time,any fingerprint can be unlocked
3.2To register fingerprints (addother users)
Insertthepininto theset-hole,you will hear two short "beep"sounds andtheredandblueLEDsflashalternately,whichmeansyouonregistration
After the master's fingerprint verification,the new userscan the fingerprint to register,and each fingerprintneedstobescanned three timestocomplete Whenanewuserfingerprintisadded,itmustbeconfirmedbythemaster fingerprint.
Start Up
Modification
Deleteall fingerprints
Insertthepininto theset-hole,you willhear twoshort "beep"sounds,and thered andblue LEDs flash alternately,which meansyou are onregistrationmode.
Insertthepin intheset-holefor five seconds,you willhear fivetimes"beep"and threetimeslong"beep"sound,the blue LEDwillon.Pressing themasterfingerprint toverify,you willhearalong"beep"andalltheregistered fingerprinte will bedeleted
2.1 fingerprint.1 Logi (Factory Reset)
LED (Blue)
●Pressthefingerprinttoregister.Eachfingerprintneedstobescanned threetimestocomplete.Afterthe completion,theredandblueLEDs willcontinue toflash,and other fingerprintscan beregistered.
●Everyfingerprintregistration,youwillhearalong"beep"sound.Thefirstthreefingerprintsaremaster fingerprints,whichcanbeusedtounlock,registernew
Power shortage
pressing the fingerprint.
Whenthe battery islow,thebattery indicator willonwhen When it is charging thebatteryindicatorwillon.Theindicatorwillbefainted,whenitisfullycharged
产品 Product
Product Description ofBroken BridgeAluminum ElectronicLock
1304不锈钢材料，能有效阻隔高温，具性能有优良的防水性能
|电量低：4节7号电池，使用时间长达一年，同时设备外接USB应急充电口
■LED触摸屏：5A级钢化触摸屏，抗打击性能强，不留划痕
■304不锈钢合金一体打造工艺，保护指纹更全面，防尘，防潮防静电，无痕面板更安全
适用范围：庭院门、断桥铝门、阳光门、铝合金门、肯德基门、纱窗门
功能：密码 ^ + 刷卡 ^ + 指纹 ^ + 机械钥匙
门锁均经过高低温、振动、老化等测试、适应恶劣环境
断桥铝指纹锁
| 类型 | 明细 |
| 四合一开锁 | 指纹+密码+刷卡+钥匙 |
| 锁体 | 3085锁体、3585锁体 |
| 标配门厚 | 40-60mm |
| 表面处理 | SUS304电镀 |
| 指纹头识别器 | 半导体指纹头 |
| 密码长度 | 6位开门密码 |
| 内材质 | 不锈钢 |
| 包装 | 纸箱 |
| 机电分离模块 | 支持 |
| 锁芯 | 超C级别 |
| 电池 | 4节7号电池 |
| 配色 | 哑光黑钢色 |
| 管理员 | 2个 |
| 用户容量 | 300个(密码100,卡100,指纹100) |
Broken Bridge Aluminum FingerprintLock
| Type | Details |
| Four in one lock | Fingerprint+password+swipecard+key |
| Lock body | 3085Lockbody、3585Lockbody |
| Standard door thickness | 40-60mm |
| Finish | SUS304 Plating |
| Fingerprint head identifier | Semiconductor fingerprint head |
| Password length | 6-digit open-doorpassword |
| Internal material | Stainless steel |
| Packing | Carton |
| Electromechanical Separation Module | Support |
| Lock core | Super Clevel |
| Battery | 4 section7battery |
| Color matching | Matteblack steel |
| Administrators | 2 |
| User capacity | 300 (password 1o0,card 1oo,fingerprint 100) |
Characteristicanddescription
304 stainless steel material,caneffectively block high temperature,with excellent waterproof performance
Low powerconsumption4No.7battries,withalifeofuptooneyearandUBemergencychargingportsoutsidetheuipment
LED touch screen: 5A Steel Touch Screen,strong anti-impactperformance,no scratches
304 stainless steel alloy integrated manufacturing process,protect fingerprints more comprehensive dust-proof,moisture-proof and static-proof, traceless panel is safer
Application scope:Courtyard Door, Broken Bridge Aluminum Door,Sunshine Door,Aluminum Alloy Door,KFC Door,Screen Window Door
Functions: password ^ + swipecard ^ + fingerprint ^ + mechanical key
Thedoor locks have been tested by high and low temperature,vibrationand aging toadapt to harsh environment
技术指导
Technical index
| 指纹图像抓取及 比对速度 | 1:N |
| 储存容量 | 标配200枚指纹数据 （根据用户需要可扩展） |
| 传感器类型 | 电容触摸式传感器 |
| 分辨率 | 508DPI |
| FRR. | |
| FAR. | |
| 指纹传感器形状 | 圆形MG105-R |
| 指纹传感器尺寸 | Φ12.8mm（直径） |
| 金属外框结构尺寸 | Φ17.7mm（R5型号外框直径） |
| 图像灰度等级 | 8位灰度 |
| 使用寿命 | 一百万次 |
| 电压/电流 | 3.3V/40mA |
| 静电测试 | 接触放电8KV/空气放电15KV |
| 数据接口 | RS232（TTL电平） |
| 工作环境 | 温度：-20℃~70℃ 湿度：40%RH-85%RH（无疑霜） |
| 储存环境 | 温度：-40℃~85℃ 湿度： |
| Speed of fingerprint image capture and comparison | 1:N |
| Storage capacity | 200 fingerprint data (scalable according to user'sneeds) |
| Sensor type | Capacitance Touch Sensor |
| Resolving power | 508DPI |
| FRR. | |
| FAR. | |
| Fingerprint sensor Shape | Round MG105-R |
| Fingerprint sensor size | Φ12.8mm(diameter) |
| Structure dimensions of metal frames | Φ17.7mm(Diameter of R5 Outer Frame) |
| Gray level of image | 8bit grayscale |
| Service life | One million times |
| Voltage/current | 3.3V/40mA |
| Electrostatic test | Contactdischarge8KV/airdischarge15KV |
| Datainterface | RS232(TTL level) |
| Work environment | Temperature: -20℃~70℃ Humidity: 40%RH-85%RH (No frost) |
| Storage environment | Temperature:-40℃~85℃ Humidity: |
Guangzhou FlyGlobe Lock.,Ltd
Add:No.13HongXing IndustyRoadShijingBaiyunDistrictGuangzhou City,GuangdongProvince,China. Tel:020-81123823 Fax:020-81123822
Website:www.fq-lock.com
E-mail:flyglobelock@126.com
ZhongshanFlyGlobeMetal ProductsCo.,Ltd Add:NorthofIndustryAvenue,XiaoLanTown,Zhongshan CityGuangdongProvince,China.
本公司保留对所有内容的修改权和解释权
