43222迪士尼灰姑娘城堡遥控灯光安装教程

43222 Disney Cinderella castle remote control lighting installation tutorial

灯光材料如下

首先，将城堡拆成两部分

Lighting materials are as follows

First, break the castle into two parts

拿出底座的部分

拿出A包

Take out the base part

Take out bag A

1

2

3

4

5 6

7

4灯先不安装

A包路线图

拿出第一节2灯灯组安装如下

A package roadmap

Take out the first section 2 lights and install the lamp group as follows

将第2个灯组如图穿过积木

Put the second set of lights through the block

将第2个灯组安装如下

安装另一侧的灯组

Install the second light group as follows

Install the light group on the other side

将第3个灯组安装如下

将剩下的灯组延箭头方向穿过

Install the third light group as follows

Run the rest of the lights through the arrow

将第4个灯组安装如下

Install the fourth light group as follows

将剩下的积木导线穿过积木

将第5个灯光组安装如下

Wire the remaining blocks through the blocks

Install the fifth light group as follows

安装第6个灯光组

安装第7个灯光组

Install the sixth light group

Install the 7th light group

安装完成后，4灯灯组先不安装

将积木翻转，安装B包灯组

After the installation is complete, do not install the 4 light group

Turn the block over and install the B pack light set

将第一节灯条安装如图

将积木拆起

Remove the blocks

Install the first light bar as shown in the figure

将导线藏于积木内并还原积木

Hide the wire in the block and restore the block

将积木拆起，把黄色积木件拆出替换成带开

口的配件

Remove the blocks and replace the yellow blocks with tape

把灯粒放配件内并把积木安装还原

Place the lamp in the fitting and restore the building blocks

将上方的积木拆起如下

Remove the top block as follows

将第2节灯条安装如下

积木还原

Install the second light bar as follows

Building block reduction

将最后一颗灯粒相同方式安装如下

将积木安装还原

Install the last lamp in the same way as follows

Install and restore building blocks

拿出C包和D包灯光组

将配件安装在灯组上

Take out pack C and Pack D lighting group

Install fittings on lamp set

将灯组安装在如图位置

Install the lamp group in the position shown

拿出第二部分的积木

拿出E包灯光组

Take out the second block

Take out the E pack lighting group

将第一个灯组安装如下.将剩下的导线延

箭头方向穿过

安装第2个灯组

Install the first light group as follows. Extend the rest of the wire

Install the second light set

将第3个灯组延箭头方向穿过后安装如下

将第4个灯组安装如下

Install the third light group as follows after passing it along the arrow directionInstall the fourth light group as follows

将导线绕在积木上拿出配件安装最后一颗灯粒

拿出F包灯光组

Wrap the wire around the block and take out the fitting to install the last

light particle

Take out the F pack lighting group

将第1个灯组安装如下

将积木拆起，把导线穿过积木

Install the first light group as follows

Remove the block and run the wire through the block

将第2个灯光组安装如下

将第3个灯光组安装如下

Install the second light group as follows

Install the third light group as follows

将导线藏于积木后

将第4个灯光组安装如下

Hide the wires behind the blocks

Install the fourth light group as follows

将第5个灯光组安装如下

将第6个灯光组安装如下

Install the fifth light group as follows

Install the sixth light group as follows

拿出单独的一节2灯灯组安装如下

Take out a separate section of 2 lamp sets installed as follows

最后将单独一颗灯粒的导线绕在积木上

并将灯粒放配件内安装如下

Finally, wrap the wire of a single light particle around the building block

and place the light particle in the accessory for installation as follows

将第二部分的积木安装还原，并将A包的

4灯灯组安装如下

Restore the building blocks of the second part, and install the 4 lamp group

of package A as follows

镭射灯安装如下

The laser light is installed as follows

镭射灯自由放置，不固定

将所有灯光插头接入连接板内再插入电池

The laser light is placed freely, not fixed

Plug all lights into the connector and plug in the battery

电池充电

battery charge