Eberry low voltage fittings - 电子书在线预览、各类电子书在线制作-云展网平台

Introduction

EBSl series products have alarge flow capacity, with maximum discharge current of 60-lookA for single pole module, and are suitable for B-level protection in low-voltage distribution systems. Different combination wiring methods are chosen based on different power supply systems.

High energy varistor, nanosecond response speed;

Equipped with overheating and overcurrent protection;

Local indicationl) and remote alarm contact2);

1) It visually displays the working status of the protector on the protector

2) It provides contacts for remote monitoring of protector status, which requires external wiring.

Pluggable in charged condition, module replaceable in case of failure.

Performance parameter

Model	EBS1-60voltage limited type	EBS1-80voltage limited type	EBS1-100voltage limited type
Maximum continuous operating voltage1) Uc(V)	385	385	385
Nominal discharge current In 8/20μs(kA)	30	40	50
Maximum discharge current 8/20μs(kA)	60	80	100
Voltage protection level Up(kV)	2.0	2.5	3.0
Back-up protective device (fuse)	63	100	125
Local failure indication	Window in green: normal, window in red: failure
Remote alarm contact	A normally open contact
Wiring capacity	1.5~35mm2
Overall dimension	90×27×62
Shell material	It complies with UL 94V-0
Shell protection class	IP20
Installation mode It is installed with TH35-7.5 (DIN35mm) standard guide rail

Note 1): The maximum continuous operating voltage is optional, with 275V, 385V, 420V, etc.

Model and specification

No. Model	Number ofpoles	Uc(M)	In(kA)	Imax(kA)	Up(kV)	Usage
1 EBS1-60/3-320	3	320	30	60	2.0	For TN-C, IT and TN-S system
2 EBS1-80/3-320	3	320	40	80	2.0
3 EBS1-100/3-320	3	320	60	100	2.5
4 EBS1-60/3N-320	3	320	30	60	2.0	$\mathsf { F o r } ^ { * } 3 + 1 ^ { * }$ combination and full-module combination
5 EBS1-80/3N-320	3	320	40	80	2.0
6 EBS1-100/3N-320	3	320	60	100	2.5
7 EBS1-60/4-320	4	320	30	60	2.0	For three-phase system of TN-S system
8 EBS1-80/4-320	4	320	40	80	2.0
9 EBS1-100/4-320	4	320	60	100	2.5
10 EBS1-60/3N-385	3	385	30	60	2.0	$\mathsf { F o r } ^ { * } 3 + 1 ^ { * }$ combination
11 EBS1-80/3N-385	3	385	40	80	2.5
12 EBS1-100/3N-385	3	385	60	100	3.0
13 EBS1-60/4-385	4	385	30	60	2.0	For TT system
14 EBS1-80/4-385	4	385	40	80	2.5
15 EBS1-100/4-385	4	385	50	100	3.0

Overall dimension and schematic diagram

Wiring diagram for remote communication termina

Normal state

Alarm state

It provides data to remote monitoring

Remote sound alarm

1。

Remote alarm light turns on

2°-

3-220V

Installation schematic diagram

"4+0" wiring method

"3+1" wiring method

Knife Switch/Disconnector Series

Scope of application

HD series and HS series knife switches (hereinafter referred to as switches) are suitable for complete sets of power distribution equipment with frequency of AC 50Hz,rated operatingvoltage up to380V and rated operating current up to 3000A. They are used as infrequent manual connection and disconnection circuits or as disconnectors. In which:

1.1 The central handle type knife switch is mainly used for power stations and does not cut off circuits with current, serving as an disconnector.

1.2 The side front lever operating mechanism switch is mainly used in front operation and front maintenance switchgear, and the operating mechanism can be installed on both sides of the cabinet.

1.3 The central front lever operating mechanism switch is mainly used in front operation and rear maintenance switchgear, with the operating mechanism installed in the front.

1.4 Side operated handle type switch is mainly used in the power box.

1.5 Switches equipped with arc extinguishing chambers can cut offappropriate current loads, while other series of knife switches are only used as disconnectors. The product complies with the GB/T 14048.3 standard.

Model and meaning

For the 11 series,"B" represents product with protective cover

"0"represents product with no arc extinguishing chamber, "1"

represents product with arc extinguishing chamber

For the 11 series,"8"represents front-panel wiring

"9" represents back-panel wiring

Number of poles (2,3, 4)

Agreed heating current(A)

-Additional code: For the 11 series,"F"represents disconnector (see HD11Fdisconnector selection for details) For 13 series,"BX" represents rotary operation, and it represents lever operation without "BX"

Design code:"11" represents the central handle type

"12"represents the side frontlever operating mechanism type

"13" representsthe central frontlever operating mechanism type

"14" represents the side operating handle type

"HD" represents open type knife switch, and "HS" represents a double-throw knife change-over switch.

Main parameters and technical performance

Conventional heatingcurrent (A)	100	200	400	600	1000	1500	2000	3000
Rated operatingcurrent (A)	100	200	400	600	1000	1500	2000	3000
On-off capacity (A)AC 380V	100	200	400	600	1000	1500		-
Mechanical life (time)	10000	10000	10000	5000	5000	5000	3000	3000
Electrical life (time)	=	1000	1000	500	500	500	300	300
1S short-time withstandcurrent (kA)	5	10	15	20	25	30	30	50
Operating force (N)	≤300	≤300	≤400	≤400	≤450	≤450	≤450	≤450

Table 3 (mm)

Overall andinstallation dimension

5.1 HD11 front-panel wiring (see Figure 1 and Table 2). Figure 1

specification	100A			200A			400A			600A			1000A			1500A
specification	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P
A	85	140	190	190	190	260	190	210	300	240	260	360	280	320	440	300	350	480
B	200	200	200	210	210	230	270	270	300	350	330	330	380	360	360	410	390	390
C	-	50	100	140	70	140	160	80	160	200	100	200	240	120	240	260	130	260
D	140	140	140	140	140	140	190	190	190	140	140	140	140	140	140	140	140	140
E	50	50	50	70	70	70	80	80	80	100	100	100	120	120	120	130	130	130
F	160	160	160	162	162	162	210	210	210	274	274	274	284	284	284	330	330	330
H	210	220	220	220	220	235	270	270	270	330	310	310	380	360	360	390	370	370
h	120	120	120	120	120	120	135	135	135	140	125	125	175	160	160	175	160	160
J	110	110	110	110	110	110	146	146	146	234	234	234	208	208	208	230	230	230
K	-	-	-	-	-	-	-	1	1	40	40	40	50	50	50	70	70	70
M	8	8	8	8	8	8	12	12	12	16	16	16	12	12	12	12	12	12
φ	6	6	6	7	7	7	7	7	7	9	9	9	9	9	9	11	11	11

5.2 HD11 back-panel wiring (see Figure 2 and Table 3) Figure 2

specification	200A			400A			600A			1000A			1500A
specification	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P
A	200	200	270	200	220	300	240	270	370	280	330	450	300	380	510
B	230	230	250	280	280	310	340	320	320	380	360	360	410	390	390
C	140	70	140	160	80	160	200	100	200	240	120	240	260	130	260
D	160	160	160	190	190	190	220	220	220	260	260	260	300	300	300
E	70	70	70	80	80	80	100	100	100	120	120	120	130	130	130
F	190	190	190	215	215	215	240	240	240	290	290	290	340	340	340
H	220	220	240	270	270	300	330	310	310	380	360	360	390	370	370
h	120	120	120	135	135	145	140	125	125	175	160	160	175	160	160
I	35	35	35	35	35	35	36	36	36	36	36	36	40	40	40
J	60	60	60	70	70	70	140	140	140	160	160	160	180	180	180
K	20	20	20	30	30	30	40	40	40	50	50	50	70	70	70
Mφ	8	8	8	12	12	127	169	16	16	12	12	129	1211	12	12
Mφ	7	7	7	7	7	127	169	9	9	9	9	129	1211	11	11

5.3 HS11 front-panel inlet back-panel outlet (see Figure 3 and Table 4). Figure 3

specification	200A			400A			600A			1000A			1500A
	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P
A	160	190	265	200	220	300	240	270	370	280	330	450	300	380	510
B	330	330	370	395	395	455	500	460	460	560	520	520	580	540	540
C	140	70	140	160	80	160	200	100	200	240	120	240	260	130	260
D	220	220	220	260	260	260	220	220	220	220	220	220	260	260	260
E	70	70	70	80	80	80	100	100	100	120	120	120	130	130	130
F	245	245	245	285	285	285	354	354	354	374	374	374	434	434	434
H	240	240	240	280	280	300	390	370	370	450	430	430	470	450	450
h	100	100	100	110	110	110	100	95	95	150	145	145	160	150	150
I	35	35	35	35	35	35	36	36	36	36	36	36	40	40	40
J	170	170	170	216	216	216	320	320	320	304	304	304	340	340	340
K	20	20	20	30	30	30	40	40	40	50	50	50	70	70	70
N	-	-	-	-	-	-	30	30	30	40	40	40	46	46	46
M	8	8	8	12	12	12	16	16	16	12	12	12	12	12	12
φ	7	7	7	7	7	7	9	9	9	9	9	9	11	11	11

5.4 HS11 back-panel wiring (see Figure 4 and Table 5). Figure 4

specification	200A			400A			600A			1000A			1500A
specification	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P
A	170	200	270	200	220	300	240	270	370	280	330	450	300	380	510
B	330	330	370	395	395	455	500	460	460	560	520	520	580	540	540
C	140	70	140	160	80	160	200	100	200	240	120	240	260	130	260
D	220	220	220	260	260	260	300	300	300	340	340	340	390	390	390
E	70	70	70	80	80	80	100	100	100	120	120	120	130	130	130
F	245	245	245	285	285	285	340	340	340	390	390	390	450	450	450
H	240	240	240	280	280	300	330	310	310	380	360	360	390	370	370
h	120	120	120	135	135	145	140	125	125	175	160	160	175	160	160
I	35	35	35	35	35	35	36	36	36	36	36	36	40	40	40
J	120	120	120	140	140	140	220	220	220	250	250	250	285	285	285
K	20	20	20	30	30	30	40	40	40	50	50	50	70	70	70
N	-	-	-	-	-	-	30	30	30	40	40	40	46	46	46
M	8	8	8	12	12	12	16	16	16	12	12	12	12	12	12
φ	7	7	7	7	7	7	9	9	9	9	9	9	11	11	11

5.5 HD12 overall and installation dimension (see Figure 5 and Table 6). Table 5 (mm) Operating handle panel cut-out diagram

specification	200A			400A			600A			1000A			1500A
specification	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P	2P	3P	4P
A	200	280	360	220	310	400	250	330	430	300	400	520	330	440	570
B	200	200	200	210	210	210	294	294	294	318	318	318	354	354	354
C	160	80	160	180	90	180	200	100	200	240	120	240	260	130	260
D	160	160	160	160	160	160	160	160	160	160	160	160	160	160	160
E	80	80	80	90	90	90	100	100	100	120	120	120	130	130	130
G	40	40	40	30	30	30	30	30	30	30	30	30	30	30	30
H	80	80	80	90	90	90	95	95	95	110	110	110	110	110	110
J	130	130	130	166	166	166	254	254	254	242	242	242	254	254	254
K	1	-	-	-	-	-	40	40	40	50	50	50	70	70	70
L	75	75	75	75	75	75	80	80	80	80	80	80	80	80	80
R	180	180	180	180	180	180	180	180	180	230	230	230	230	230	230
M	8	8	8	12	12	12	16	16	16	12	12	12	12	12	12
①	7	7	7	7	7	7	9	9	9	9	9	9	11	11	11

5.6 HS12 overall and installation dimension (see Figure 6 and Table 7). Figure 6 Table 7 (mm) Operating handle panel cut-out diagram for 1000Aand below Operating handle panel cut-out diagram for 1500A

specification	200A		400A		600A		1000A		1500A
specification	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P
A	280	360	310	400	330	430	400	520	440	570
B	280	280	305	305	394	394	434	434	485	485
C	80	160	90	180	100	200	120	240	130	260
D	240	240	240	240	240	240	240	240	260	260
E	80	80	90	90	100	100	120	120	130	130
G	40	40	30	30	30	30	30	30	30	30
H	80	80	90	90	95	95	110	110	110	110
I	35	35	35	35	36	36	36	36	40	40
J	210	210	256	256	354	354	362	362	385	385
K	20	20	30	30	40	40	50	50	70	70
L	75	75	75	75	70	70	60	60	70	70
N	-	-	-	-	30	30	40	40	46	46
R	180	180	180	180	180	180	230	230	230	230
M	8	8	12	12	16	16	12	12	12	12
φ	7	7	7	7	9	9	9	9	11	11

5.7 HD13 overall and installation dimension (see Figure 7 and Table 8). Figure 7

specification	200A		400A		1000A 3P		1500A 4P		3000A
specification	3P 4P	3P		600A 3P 4P		4P 3P		2000A 3P 4P		3P 4P
A	210	300 245	4P 335	260 370	310	440	340 480	480	660	580 780
B	200	200	210 210	294	294	318 318	354 354	360	360	400 400
C	80	160	90 180	100	200 120	240	130 260	180	360 200	400
D	160	160	160 160	160	160 160	160	160 160	160	160 160	160
E	80	80	90 90	100	100 120	120	130 130	180	180	200 200
H	160	160	185	185 190	190	230 230	235 235	230	230	235 235
J	130	130	166	166 254	254	242 242	254 254	250	250	280 280
K	-	-	- -	40	40	50 50	70 70	100	100	120 120
L	75	75	75 75	80	80	80 80	80 80	80	80	80 80
R	180	180	180 180	180	180	230 230	230 230	280	280	280 280
M	8	8	12 12	16	16	12 12	12 12	12	12	16 16
φ	7	7	7	7 9	9	9 9	11 11	11	11	11 11

5.8 HS13 overall and installation dimension (see Figure 8 and Table 9). Figure 8

Table 9 (mm)

specification	200A		400A		600A		1000A		1500A		2000A		3000A
specification	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P
A	210	300	240	335	270	370	330	450	370	500	500	680	600	800
B	280	280	300	300	394	394	434	434	485	485	480	480	540	540
C	80	160	90	180	100	200	120	240	130	260	180	360	200	400
D	240	240	240	240	240	240	240	240	260	260	260	260	260	260
E	80	80	90	90	100	100	120	120	130	130	180	180	200	200
H	160	160	185	185	190	190	235	235	255	255	235	235	260	260
I	35	35	35	35	36	36	36	36	40	40	48	48	50	50
J	210	210	256	256	354	354	362	362	385	385	370	370	404	404
K	-	-	-	一	40	40	50	50	70	70	100	100	120	120
L	75	75	70	70	70	70	60	60	70	70	60	60	70	70
N	-	-	-	-	30	30	30	30	46	46	50	50	50	50
R	180	180	180	180	180	180	230	230	280	280	280	280	280	280
M	8	8	12	12	16	16	12	12	12	12	12	12	16	16
φ	7	7	7	7	9	9	9	9	11	11	11	11	11	11

5.9 HD13BX overall and installation dimension(see Figure 9 and Table 10).

5.10 HS13BX overall and installation dimension (see Figure 10 and Table 11).
table10

specification	200A		400A		600A		1000A		1500A		2000A		3000A
specification	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P
A	210	300	245	335	260	370	310	440	340	480	480	660	580	780
B	200	200	210	210	294	294	318	318	354	354	360	360	400	400
C	80	160	90	180	100	200	120	240	130	260	180	360	200	400
D	160	160	160	160	160	160	160	160	160	160	160	160	160	160
E	80	80	90	90	100	100	120	120	130	130	180	180	200	200
H	160	160	185	185	190	190	230	230	235	235	230	230	235	235
J	130	130	166	166	254	254	242	242	254	254	250	250	280	280
K	-	-	-	-	40	40	50	50	70	70	100	100	120	120
L	130	130	130	130	135	135	135	135	135	135	135	135	135	135
M	8	8	12	12	16	16	12	12	12	12	12	12	16	16
φ	7	7	7	7	9	9	9	9	11	11	11	11	11	11

specification	200A		400A		600A		1000A		1500A		2000A		3000A
specification	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P	3P	4P
A	210	300	240	335	270	370	330	450	370	500	500	680	600	800
B	280	280	300	300	394	394	434	434	485	485	480	480	540	540
C	80	160	90	180	100	200	120	240	130	260	180	360	200	400
D	240	240	240	240	240	240	240	240	260	260	260	260	260	260
E	80	80	90	90	100	100	120	120	130	130	180	180	200	200
H	160	160	185	185	190	190	235	235	255	255	235	235	260	260
I	35	35	35	35	36	36	36	36	40	40	48	48	50	50
J	210	210	256	256	354	354	362	362	385	385	370	370	404	404
K	-	-	-	-	40	40	50	50	70	70	100	100	120	120
L	75	75	70	70	70	70	60	60	70	70	60	60	70	70
N	-	-	-	-	30	30	30	30	46	46	50	50	50	50
M	8	8	12	12	16	16	12	12	12	12	12	12	16	16
φ	7	7	7	7	9	9	9	9	11	11	11	11	11	11

5.11 HD(HS)13BX-2000, 3000/31, 41 overall and installation dimension (see Figure 11, Table 12)

Figure 11

Product model	A	B	C	D	E	H	J	K	L	M	①
HD13BX-2000/31	530	318	180	160	180	230	242	50	135	12	11
HD13BX-2000/41	710	318	2-180	160	180	230	242	50	135	12	11
HD13BX-3000/31	710	354	230	160	230	235	254	70	135	12	11
HD13BX-3000/41	940	354	2-230	160	230	235	254	70	135	12	11
HS13BX-2000/31	530	434	180	260	180	235	362	50	115	12	11
HS13BX-2000/41	710	434	2-180	260	180	235	362	50	115	12	11
HS13BX-3000/31	710	485	230	260	230	235	385	70	125	12	11
HS13BX-3000/41	940	485	2-230	260	230	235	385	70	125	12	11

5.11 HD14 overall and installation dimension(see Figure 12 and Table 13)

Table 13 (mm)

specification	200A		400A		600A		1000A	1500A
specification	3P	4P	3P	4P	3P	4P	3P	3P
A	280	360	310	400	330	430	400	440
B	200	200	210	210	294	294	314	354
C	80	160	90	180	100	200	120	130
D	160	160	160	160	160	160	160	160
E	80	80	90	90	100	100	120	130
G	100	100	100	100	100	100	100	100
H+L	160+80	160+80	185+90	185+90	190+90	190+90	230+110	235+110
L1	48	48	48	48	48	48	53	53
J	130	130	166	166	254	254	242	254
K	-	-	-	一	40	40	50	70
R	250	250	250	250	250	250	250	250
M	8	8	12	12	16	16	12	12
φ	7	7	7	7	9	9	9	11

Scope ofapplication

EBHD11FA series disconnectors are suitable for circuits with rated insulation voltage of 660V, rated operating voltage of 400V and rated operating current from 200A to1600A. They are mainly used in low-voltage complete equipment, and are used for openingand closing circuits and isolating power sources without load. The technical performance of this disconnector complies with the standards of IEC60947-3 and GB/T14048.3.

Model and meaning

3 digits, 3in the first digit represents 3 poles, 8/9 in the second digit representsfront/backpanel wiring,1 in thethirddigit represents product with auxiliarycontact,0 represents product without auxiliary contact,and 0 can be omitted when there is no auxiliary contact Rated operating current

Derived sequence number

Anti-misoperation type

Central handle type

Disconnector

Enterprise code

Main technical parameters

Ratedoperatingvoltage (V)	Agreed heatingcurrent (A)	Rated short timewithstandcurrent(effective)(kA)	Power factorcosΦ	Ratio ofpeakto effectivevalue	Power-ontime (s)
AC400	200	10	0.3	1.7	1
	400	20	0.3	2.0
	630(600)	20	0.3	2.0
	1000	25	0.25	2.1
	1600(1500)	32	0.25	-

Overall and installation dimension

Figure1 HD11FA-200\~1600/38(Front-panel wiring)

Rated operatingvoltage (V)Overall	Overall dimension
	Overall dimension				Installation dimension
	A	B	E	F	M	C	D	①
200	190	204	70	152	M8	70	140	①7
400	210	248	80	163	M12	80	190	①7
630	260	282	100	168	M16	100	140	①9
1000	310	304	120	192	2-M12	120	140	①9
1600	350	335	130	210	4-M12	130	150	①11

Product overview

EBHH15(QSA) series disconnector-fuse group, HH 15A(OA); HH15P(QP) series disconnectors are mainly suitable for distribution circuits and motor circuits with high short-circuit current. They are used as manual and infrequent main switches or master switches, especially suitable for installation in higher withdrawable low-voltage switchgear assemblies. The product complies with GB/T 14048.3 and IEC60947-3 standards.

Model and meaning

Number of auxiliary contacts: 0- no auxiliary contact. 1- with 1 pair of auxiliary

contacts.2-with 2 pairs of auxiliary contacts

Number of poles (3, 4)

Agreed heating current (A)

Single throw: "QA" represents no fuse, series contact structure (double break point); Double throw: QAS

"Qp" represents no fuse, parallel contact structure (single breakpoint);

"QSA" represents product equipped with fuse, series contact structure

(double break point);

Design code

Disconnector-fuse group

Enterprise code

Structural feature

1. The switch adopts a fully enclosed structure to ensure improved reliability and stable performance;

2. It has a unique rolling plug-in contact system. Each phase has two sets of double break point contact systems, either in series orin parallel, which can meet the requirements of circuits with different current levels and different working categories.

3. The contact system allows the current to pass through several rollers separately, resulting in a significant reduction in the electric reaction force on each roller. During the movement, the contact between the roller and the fixed contact has both rolling and sliding friction, which can effectively avoid fusion welding

4. The operating mechanism has energy storage spring, so the movement speed of the moving contact group is independent of the magnitude of the operating force and the operating speed.

5. The actuator consists of handle mounted on the panel, drive coupling that engages with the handle, extension shaft, coupling and drive shaft. The extension shaft and coupling are only used when the drive shaft is not long enough.

6. The depth of installation of switches in complete set of cabinet can be considered according to the needs of the combination installation of various electrical components, with a considerable range of activities.

HH15(QSA) series disconnector-fuse group main technical parameters
HH15 (QSA) series disconnector-fuse group overall and installation dimension

Specification		63	125	160	250	400	630	800	1000	1250
Number of main poles		3、4、3+N							3
Rated insulation voltage (V)		$\cup \mathsf { j } = 6 6 0 \mathsf { i f } \cup \mathsf { e } = 3 8 0 . \mathsf { U j } = 1 0 0 0 \mathsf { i f } \cup \mathsf { e } = 6 6 0 .$
Rated operating voltage (V)		AC 380、660
Rated enclosed heating current (A)		63	125	160	250	400	630	800	1000	1250
Rated operating	380V AC-23B	63	125	160	250	400	630	800	1000	1250
current (A)	660V AV-23B	63	100	160	250	315	425	500	630	800
Rated limited short circuit current at 380V Y/H (KA)		100							50
Rated limited short circuit current at 660V (KA)		50
Mechanical life (time)		15000	15000	12000	12000	12000	3000	500	500	500
Electrical life (time)		1000	1000	300	300	300	200	100	100	100
Rated current of the fuse at 380V/660V (A)		63/63	125/100	160/160	250/250	400/315	630/425	800/500	1000/630	1250/800
Knife contact fuse type		RDT16-00(NT00)			RDT16-1(NT1) R	DT16-2(NT2)	RDT16-3(NT3)		RSO
Operating moment (Nm)		7.5		16			30		40
Rated heating current of auxiliary contactTH380V/AC-11(A)		5

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	L3
HH15-63	12	6	100	M5	2	39.5	72	38.5	9	199-250	250-301	301-385	180-199
HH15-125	15	7.5	116	M6	3	38.5	70	40.5	10	199250	250301	301385	180199

Hh15 (QSA) series disconnector-fuse group overall and installation dimension

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	o
HH15-160	20	10	146	M8	4	44	107	65	46	226-284	284-342	342-400	120
HH15-250	25	12.5	160	M10	4	40	107	65	43.5	226-284	284-342	342-400	160
HH15-400	25	12.5	160	M10	6	38	107	65	43.5	226-284	284-342	342-400	160

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	L3
HH15-630	40	20	270	M12	6	33	87	87	60	300-355	295-330	330-400	400-500

Model andspecification	A	B	C	D	E	F	G	H	–	L	L1	L2	L3
HH15A-400	25	12.5	160	M10	4	40	107	65	43.5	226-284	284-342	342-400	188-238
HH15A-630	30	15	180	M10	6	38	107	65	43.5	226-284	284-342	342-400	188-238

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	L3	L4
HH15A-1000	40	20	270	M12	6	33	87	87	60	300-355	295-330	330-400	400-500	225-260

HH15P(QP) series disconnector overall and installation dimension

HH15P(QP) series disconnector main technical parameters

Specification		250	630	1000	1250	1600	2500	3150
Number of main poles		3
Rated insulation voltage (V)		$\cup \mathsf { j } = 6 6 0 \mathsf { i f } \cup \mathsf { e } = 3 8 0 . \mathsf { U j } = 1 0 0 0 \mathsf { i f } \cup \mathsf { e } = 6 6 0 .$
Rated operating voltage (V)		AC 380、660
Rated enclosed heating current (A)		250	630	1000	1250	1600	2500	3150
Rated operatingcurrent (A)	380V AC-21B	250	630	1000	1250	1600	2500	3150
Rated operatingcurrent (A)	660V AV-22B	250	630	630	630	800	-	-
	660V AV-23B	250	630	1000	1250	1470	2500	2500
Rated short circuit making capacity (peak) (kA)		17	50	67.2	67.2	85	130	130
Rated limited short circuit current at 660V (KA)		10	15	32	32	50	80	80
Mechanical life (time)		15000	12000	12000	1000	1000	300	300
Electrical life (time)		1000	300	150	100	100	100	100
Operating moment (Nm)		7.5	16	16	30	30	70	70
Rated heating current of auxiliary contactTH380V/AC-11(A)		5

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	L3
HH15P-250	25	125	143	M10	4	37.5	66	44.5	12.5	199-250	250-301	301-385	148-199

Model andspecification	A	B1	B2	C	D	E	F	G	H	一	L	L1	L2	L3
HH15-800	50	18	40	340	M12	6	33	87	87	60	300-355	295-330	330-400	400-500
HH15-1000	50	18	40	340	M12	7	33	87	87	60	300-355	295-330	330-400	400-500

Model andspecification	A	B	C	D	E	F	G	H	一	L	L1	L2	M	N	o
HH15-1250-1000A	70	17	370	M10	7	50	120	120	80	395-430	495-530	560-595	400	330	253
HH15-1250	70	17	370	M10	8	50	120	120	80	395-430	495-530	560-595	400	330	253

HH15A(QA)series disconnector main technical parameters

Specification		125	160	200	400	630	1000
Number of main poles		3
Rated insulation voltage (V)		$\cup \mathsf { j } = 6 6 0 \mathsf { i f } \cup \mathsf { e } = 3 8 0 . \mathsf { U j } = 1 0 0 0 \mathsf { i f } \cup \mathsf { e } = 6 6 0$
Rated operating voltage (V)		AC 380、660
Rated enclosed heating current (A)		125	160	200	400	630	1000
Rated operatingcurrent (A)	380V AC-21B	125	160	200	400	630	1000
Rated operatingcurrent (A)	660V AV-22B	125	160	160	315	425	800
	660V AV-21B	125	160	200	400	630	1000
Rated short circuit making capacity (peak) (kA)		17	17	17	50	50	67.2
Rated limited short circuit current at 660V (KA)		10	10	10	15	15	32
Mechanical life (time)		15000	15000	15000	12000	12000	30000
Electrical life (time)		1000	1000	100	300	300	150
Operating moment (Nm)		7.5			16		30
Rated heating current of auxiliary contactTH380V/AC-11(A)		5

HH15A(QA) series disconnector overall and installation dimension

Model andspecification	A	B	C	D	E	F	G	H	I	L	L1	L2	L3
HH15A-125	15	7.5	116	M6	3	38.5	70	40.5	10	199-250	250-301	301-385	148-199
HH15A-160	20	10	127	M8	3	38.5	65	45.5	13	199-250	250-301	301-385	148-199
HH15A-200	20	10	127	M8	3	38.5	65	45.5	13	199-250	250-301	301-385	148-199

Model andspecification	A	B	C	D	E	F	G	H	一	L	L1	L2	L3	M	o
HH15P-630	30	15	170	M10	5	39	107	65	43.5	226-2842	84-3423	42-4001	80-238	140	119
HH15P-1000	40	20	218	M12	6	32	117	80	51	226	-2842284-3423	42-4001	80-238	140	125

Model andspecification	A	B	C	D	E	F	G	H	一	L	L1	L2	L3	L4
HH15P-1250	40	20	350	2×M12	10	29	87	87	60	300-355	295-330	330-4004	00-500	225-260
HH15P-1600	50	20	350	2×M12	10	29	87	87	60	300-355	295-330	330400	-400-500	225-260

Model andspecification	A	B	C	D	E	F	G	H	一	L	L1	L2	L3	L4	M	o	T
HH15P-2500	80	20	446	M12	12.5	171.5	100	100	47	480 -510	455 -490	490 -560	560 -600	385-420	400	170	40
HH15P-3150	100	20	462	M12	14	172.5	87	87	60	480	455-510	-490490	560-600-560	385-420	400	167.5	50

Panel cut-out dimension

HH15(QSA)-63\~125
Hh15(AQA)-125\~200
Hh15(PQP)-250

HH15(QSA)-160\~1250; Hh15(AQA)-400\~1000 Hh15(PQP)-630\~3150

Ordering instructions

The HH15 series disconnector must be used together with fuse. The fuse can be provided by the user, but please choose a better fuse to prevent high temperature rise.

The switch price provided by our company do not include fuse. If the user requests it during the order, our company can provide matching fuses, but it isgenerally not installed on the switch body.

When users open the packaging, please check the following accessories:

a) Switch body: 1 set

b) Insulation partition: 5 pieces (dedicated for HH15)

c) Square shaft and handle: 1 set

d) Certificate of conformity and instruction manual: 1 copy

Product overview

HR6 series fuse type disconnector (hereinafter referred to as switch). It is mainly used as power switches, isolation switches, emergency switches and circuit protection in distribution circuits and motor circuits of high short-circuit current with rated voltage of AC 380\~660V (50/60Hz) and agreed heating current up to 800A, but generally it's not used for direct opening and closing of a single motor.

The performance of this product complies with the standards of IEC60947-3 and GB/ T14048.3.

Model and meaning

"0" represents no fuse signal device

"1" represents fuse signal device type(equipped with micro switch)

Number of poles, 3 means three poles

Rated operating current: 160A, 250A, 400A, 630A, 800A five types

Design code

Fuse type disconnector

Structural feature

The switch consists of base, cover, and arc extinguishing chamber, is completely made of arc resistant plastic and is a fully plastic structure. The fixed contact is directly installed on the base, making the arc extinguishing chamber easy to disassemble and assemble. The arc extinguishing chamber has two parts: an inner chamber and an outer chamber, and multiple metal arc extinguishing grids are used to increase the arc extinguishing ability and improve the contact life.

The NT type fuse link is installed inside the cover, which can rotate in a fan-shaped manner along the support, and has a large electrical isolation to meet the requirements of the disconnector. The cover can be easily removed from the base, making it easy to install and replace the fuse link part. There are two sets of installation holes on the base to meet the requirements for installation inside various switchgear cabinets and on panels. On both sides of the switch, auxiliary contacts can be installed as needed to send signals indicating the opening and closing status of the switch.

Main technical parameters of the fuse

Model	Rated voltage (V)	Rated current (A)
NT00	400	4、6、10、16、20、25、32、35、40、63、80、100、125、160
NT00	660	4、6、10、16、20、25、32、35、40、63、80、100、125、160
NT1	400	80、100、125、160、200、224、250
NT1	660	80、100、125、160、200、224、250
NT2	400	125、160、200、224、250、300、315、355、400
NT2	660	125、160、200、224、250、300、315、355、400
NT3	400	315、355、400、425、500、630
NT3	660	315、335、400、425、500、630
RT17	400	800

Switch technical parameter

Model		HR6-160	HR6-250	HR6-400	HR6-630	HR6-800
Rated insulation voltage (V)		1000	1000	1000	1000	1000
Agreed heating current (A)		160	250	400	630	800
Rated operatingvoltage (V)	400V	160	250	400	630	800
Rated operatingvoltage (V)	660V	100	200	315	425	500
Rated making andbreaking capacity (A)(at 1.05Ue)	ON400V, COSφ =0.35 AC22BOFF	1280	2000	3200	5040	6400
	ON400V, COSφ =0.35 AC22BOFF	960	1500	2400	3780	4800
	ON660V, COSφ =0.65 AC22BOFF	480	750	1200	1890	2400
	ON660V, COSφ =0.65 AC22BOFF	480	750	1200	1890	2400
Rated fuse short circuit current kA		50	50	50	50	50
Maximum prospective peak current kA		100	100	100	100	100
Equipped NT fuse model		00	1	2	3	RT17
Pollution level		3	3	3	3	3
Installation category		III	III	III	III	III

The rated voltage of the auxiliary switch is 400V AC, the agreed heating current is 5A, the load category is AC-15, and the breaking power is 300VA.

Overall and installation dimension

Dimension	Specification
Dimension	160A	250A	400-800A
A	215	280	300
B	134	184	244
C	200	260	280
D	80	120	160
E	40	60	60
F	40	62	85
G	139	160	190
H	249	310	360
A	①7	①9	①9
B	①7	①9	①9

BSMJK and BKMJ Series self-healing low-voltage parallel capacitors (economy type)

Mounting dimension

Type	Rated Voltage(kV)	Rated Frequency(Hz)	Rated output(kvar)	Rated capacitance(MF)	Rated curret(A)	Dimension LxWxH(mm)
0.4-5-3	0.4	50	5	99.5	7.2	14552110
0.4-7.5-3	0.4	50	7.5	149	10.8	14552130
0.4-10-3	0.4	50	10	199	14.4	14552130
0.4-12-3	0.4	50	12	239	17.3	14552180
0.4-14-3	0.4	50	14	279	20.2	14552210
0.4-15-3	0.4	50	15	299	21.7	14552210
0.4-16-3	0.4	50	16	318	23.1	17270190
0.4-20-3	0.4	50	20	398	28.9	17270190
0.4-25-3	0.4	50	25	498	36.1	16787200
0.4-30-3	0.4	50	30	597	43.3	16787200
0.4-40-3	0.4	50	40	796	57.7	240120200
0.4-50-3	0.4	50	50	995	72.2	240120220
0.45-5-3	0.45	50	5	79	6.4	14552110
0.45-7.5-3	0.45	50	7.5	118	9.6	14552110
0.45-10-3	0.45	50	10	157	12.8	14552130
0.45-12-3	0.45	50	12	189	15.4	14552130
0.45-14-3	0.45	50	14	220	18	14552180
0.45-15-3	0.45	50	15	236	19.2	14552180
0.45-16-3	0.45	50	16	252	20.5	14552210
0.45-20-3	0.45	50	20	315	25.7	14552210
0.45-25-3	0.45	50	25	393	32.1	17270190
0.45-30-3	0.45	50	30	472	38.5	17270210
0.45-40-3	0.45	50	40	629	51.3	16787250
0.45-50-3	0.45	50	50	786	64.2	240120200
0.25-5-3YN	0.25	50	5	255	6.7	14552130
0.25-10-3YN	0.25	50	10	510	13.3	14552210
0.25-15-3YN	0.25	50	15	764	20	17270190
0.25-20-3YN	0.25	50	20	1019	26.7	17270210
0.25-25-3YN	0.25	50	25	1274	33.3	16787250
0.25-30-3YN	0.25	50	30	1529	40	16787280

Note: Other specifications can be customized according to user requirements.

Low voltage current transformer

Product Overview

The BH(SDH)-0.66 series current transformer casing is made of PA66 alloy material, suitable for AC circuits with a rated frequency of 50Hz and a ratedvoltage of 0.66kV or below for current and energy measurement or relay protection. It is widely used in projects such as photovoltaic (solar power) and wind power. The installation methods include busbar-fixed and base plate-fixed installation methods, making it suitable for any installation. The secondary wiring can be connected via busbars or cables. Standards: GB/T 20840.1, GB/T 20840.2

Model Meaning

Product Parameters

Current	Rated Secondary Load (VA)					Number ofTurns throughCore
Current	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH-0.66 20BH-0.66 30BH-0.66 40
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
75/5	2.5					1
100/5	2.5	2.5				1
150/5	2.5	2.5				1
200/5	5	5				1
250/5	5	5				1
300/5	5	5				1
30/5						1
40/5						1
50/5						1
75/5						1
100/5	2.5	2.5				1
150/5	2.5	2.5				1
200/5	5	5				1
250/5	5	5				1
300/5	5	5				1
400/5	5	5	2.5	2.5	2.5	1
150/5	5	5	5	5	5	1
200/5	5	5	5	5	5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5				1
Current	Rated Secondary Load (VA)					Number ofTurns throughCore
Current	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH-0.66 50 BH-0.66 60136 BH-0.66 80BH-0.66 100BH-0.66 120
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
200/5	5	5	2.5	2.5	2.5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
200/5	5	2.5				1
250/5	5	5				1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
300/5	5	5				1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
800/5	10	10				1
1000/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	1
4000/5	30	30	30	30	30	1

Product Overview

The BH(SDH)-0.66 series current transformer is suitable for use in AC circuits with a rated frequency of 50Hz and a rated voltage of 0.66kV and below for current and energy measurement or relay protection. This product is a plastic shell type current transformer, widely used in switchgear assemblies. It can be installed using either busbar-fixed or base-fixed methods and is suitable forinstallation in any direction. The secondary lead can be either busbar or cable.
Standards: GB/T 20840.1, GB/T 20840.2.

Model Meaning

Product Parameters

Current	Rated Secondary Load (VA)					Number ofTurns throughCore
Current	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH(SDH)-0.66 30 (B Type)BH(SDH)-0.66 30 Square Hole CustomizationBH(SDH)-0.66 40BH(SDH)-0.66 50
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
50/5	5	2.5				1
75/5	5	2.5	2.5	2.5	2.5	1
100/5	5	2.5	2.5	2.5	2.5	1
150/5	5	2.5	2.5	2.5	2.5	1
200/5	5	5	5	5	5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
150/5	2.5					1
200/5	2.5	2.5				1
250/5	5	5	2.5	2.5	2.5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
150/5	5	2.5	2.5	2.5	2.5	1
200/5	5	5	5	5	5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
200/5	5	5	2.5	2.5	2.5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
Current	Rated Secondary Load (VA)
Current	Rated Secondary Load (VA)					Number ofTurns through Appearance and InstallationDimensions DiagramCoreBH(SDH)-0.66 60 BH(SDH)-0.66 80 BH(SDH)-0.66100 BH(SDH)-0.66 120 BH(SDH)-0.66 130
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
400/5	5	5	5	5	5
500/5	5	5	5	5	5
600/5	5	5	5	5	5
750/5	10	10	10	10	10
800/5	10	10	10	10	10
100/5	10	10	10	10	10
1200/5	10	10	10	10	10
1500/5	10	10	10	10	10
600/5	5	5	5	5	5
750/5	10	10	10	10	10
800/5	10	10	10	10	10
1000/5	10	10	10	10	10
1200/5	10	10	10	10	10
1500/5	10	10	10	10	10
2000/5	20	20	20	20	20
750/5	10	10	10	10	10
800/5	10	10	10	10	10
1000/5	10	10	10	10	10
1200/5	10	10	10	10	10
1500/5	10	10	10	10	10
2000/5	20	20	20	20	20
2500/5	20	20	20	20	20
1000/5	10	10	10	10	10
1200/5	10	10	10	10	10
1500/5	20	20	20	20	20
2000/5	20	20	20	20	20
2500/5	20	20	20	20	20
3000/5	20	20	20	20	20
4000/5	30	30	30	30	30
800/5	10	5
1000/5	10	5	5	5	5
1200/5	10	10	10	10	10
1500/5	10	10	10	10	10
2000/5	20	20	20	20	20
2500/5	20	20	20	20	20
3000/5	20	20	20	20	20
4000/5	30	30	30	30	30
5000/5	30	30	30	30	30
Current	Rated Secondary Load (VA)					Number ofTurns throughCore
Current	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH-0.66 150BH-0.66 180BH-0.66 200BH-0.66 220BH-0.66 260
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	1
4000/5	30	30	30	30	30	1
5000/5	30	30	30	30	30	1
1500/5	10	10	10	10	10	11
2000/5	20	20	20	20	20	11
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	11111
4000/5	30	30	30	30	30
5000/5	30	30	30	30	30
2000/5	20	20	20	20	20
2500/5	20	20	20	20	20
3000/5	20	20	20	20	20	1
4000/5	30	30	30	30	30	1
5000/5	30	30	30	30	30	11
2000/5	20	20	20	20	20	11
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	1
4000/5	30	30	30	30	30	1
5000/5	30	30	30	30	30	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	1
4000/5	30	30	30	30	30	1
5000/5	30	30	30	30	30	1

Normal Operating Conditions and Installation Conditions

1.Installation Location: Indoor.

2.Ambient Temperature: -5°C to +40°C, with a daily average not exceeding +30°C.

3.Altitude: Not exceeding 1000m.

4.Atmospheric Conditions: When the maximum temperature is +40°C, the relative humidity of the air should not exceed 50%. At lower temperatures, the relative humidity can be up to 80%.

5.The atmosphere should not contain serious pollutants, and there should be no gases or conductive dust that could corrode metals or damage insulation.

6.The installation site should be free from severe vibrations or jolts.

The installation site should not be exposed to direct sunlight, and there should be no rain, snow, or serious mold contamination.

Attachment Outline and Installation Dimensions

Mounting Plate

BH-0.66、 BH(SDH)-0.66 30-60 Attachment Outline and Installation Dimensions

Mounting Plate

Fixed Plate BH-0.66、 BH(SDH)-0.66 80 Attachment Outline and Installation Dimensions

Current Transformer Installation Diagram

Busbar fixed type

Ordering Instructions

1.When ordering, please specify the product model, window width, current ratio, rated output, and corresponding accuracy class. For example:

Order description: BH(SDH)-0.66 type, window width 40mm, rated current ratio 200/5A, rated output 5VA, accuracy class 0.2.
Order description: BH-(SDH)0.6640600/5 0.2 class.

2.If the load is not marked in the system, the default parameters are those in the table. If the class is not marked in the system, the default accuracy class is 0.5.

3.If there are other requirements, please specify them in the contract.

Product Overview

The BH-0.661 series current transformer is suitable for use in AC circuits with a rated frequency of 50Hz and a rated voltage of 0.66kV and below for current and energy measurement or relay protection. The product is a plastic-shell current transformer, widely used in complete switchgear. Its installation method can adopt busbar fixation or base plate fixation, and it is suitable for installation in any direction. The primary conductors can be busbars or cables.
Standards: GB/T20840.1, GB/T20840.2

Model Meaning

Product Parameters

CurrentRatio	Rated Secondary Load (VA)
						Appearance and InstallationDimensions DiagramBH-0.66 SolidBH-0.66 Solid M8BH-0.66 Huge Solid601

	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
5/5	5	2.5
10/5	5	2.5
15/5	5	2.5
20/5	5	2.5
25/5	5	2.5
30/5	5	2.5
40/5	5	2.5
50/5	5	2.5
75/5	5	2.5
5/5	5	2.5
10/5	5	2.5
15/5	5	2.5
20/5	5	2.5
25/5	5	2.5
30/5	5	2.5
40/5	5	2.5
50/5	5	2.5
75/5	5	2.5
5/5	5	5	5	5	5
10/5	5	5	5	5	5
15/5	5	5	5	5	5
20/5	5	5	5	5	5
25/5	5	5	5	5	5
30/5	5	5	5	5	5
40/5	5	5	5	5	5
50/5	5	5	5	5	5
75/5	5	5	5	5	5

Product Overview

The BH-0.66I11 series current transformer is mainly used indoors for AC circuits with a rated voltage of 0.66kV and below and a frequency of 50Hz, for current and energy measurement or relay protection. The product is a plastic casing current transformer, widely used in complete switchgear assemblies. Its installation method can be fixed using busbars or base plates and is suitable for installation in any direction. Compared to the 1 and 11 models, it offers advantages such as larger capacity, higher accuracy, fewer accessories, and easier installation.
Standards: GR/T 20840 1.GR/T 20840.2

Standards: GB/T 20840.1, GB/T 20840.2.

Model Meaning

Product Overview

CurrentRatio	Rated Secondary Load (VA)					Number ofTurns throughCore
	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH-0.66 20IIIBH-0.66 30IIIBH-0.66 40III
	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2S Class
75/5	2.5	2.5				1
100/5	5	5				1
150/5	5	5				1
200/5	5	5				1
100/5	5	5	2.5	2.5	2.5	1
150/5	5	5	5	5	5	1
200/5	5	5	5	5	5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
150/5	5	5	5	5	5	1
200/5	5	5	5	5	5	1
250/5	5	5	5	5	5	1
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1

Normal Operating Conditions and Installation Conditions

1.Installation Location: Indoor.

2.Ambient Temperature: -5°C to +40°C, with a daily average not exceeding +30°C.

3.Altitude: No more than 1000m.

4.Atmospheric Conditions: When the maximum temperature is +40°C, the relative humidity of the air should not exceed 50%. At lower temperatures, the relative humidity can be up to 80%.

5.No severe pollution in the atmosphere, and the medium should not contain gases or conductive dust that could corrode metal or damage insulation.

3.If there are any other requirements, please specify them in the contract.

2.For unmarked loads in the system, the default parameters are those in the table. For unmarked accuracy classes, the default is 0.5.

Product Overview

Current	Rated Secondary Load (VA)					Number ofTurns throughCore
Current	Rated Secondary Load (VA)						Appearance and InstallationDimensions DiagramBH-0.66 50IIIFODBH-0.66 60IIIBH-0.66 80IIIBH-0.66 100IIIBH-0.66 120III
Ratio	1.0 Class	0.5 Class	0.5S Class	0.2 Class	0.2s Class
300/5	5	5	5	5	5	1
400/5	5	5	5	5	5	1
500/5	5	5	5	5	5	1
600/5	5	5	5	5	5	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
500/5	5	5	5	5	5	1
600/5	10	10	10	10	10	1
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
500/5	5	5	5	5	5	11
600/5	5	5	5	5	5	11
750/5	10	10	10	10	10	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
800/5	10	10	10	10	10	1
1000/5	10	10	10	10	10	1
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	11
1000/5	10	10	10	10	10	11
1200/5	10	10	10	10	10	1
1500/5	10	10	10	10	10	1
2000/5	20	20	20	20	20	1
2500/5	20	20	20	20	20	1
3000/5	20	20	20	20	20	1
4000/5	20	20	20	20	20	1

Ordering Instructions

1.When placing an order, please specify the product model, window width, current ratio, rated output, and corresponding accuracy class. For example: Order BH-0.66l type, window width 60mm, rated current ratio 600/5A, rated output 5VA, accuracy class 0.2. The order description is: BH-0.66 6011600/5 0.2.

Model Meaning

Indoor Single Phase Vertical

Dimensions and Installation Size

Specification Model	Outer Diameter Dimensions			Inner Diameter Dimensions		Parameters
Specification Model	Width	Height	Thickness	Width	Height	Parameters
BH-0.66 50P	92	128	77	33	55	200/5-800/5
BH-0.66 60P	92	144	77	33	65	400/5-1500/5
BH-0.66 80P	92	168	77	33	84	600/5-2000/5
BH-0.66 100P	124	200	77	55	104	750/5-2500/5
BH-0.66130P	124	230	77	55	134	1000/5-4000/5

Open、Bushing Current Transformer

Model Meaning

L MZ (J)1 - 0.5

Voltage Level

Design Sequence Number

Reinforced Type

Cast Resin Insulation

Busbar Type

Current Transformer

Indoor single - phase epoxy casting

Product Overview

This type of transformer is an integral casting structure, primarily suitable for use in power systems with a rated frequency of 50Hz or 60Hz and a rated voltage of 0.66kV and below for current, energy metering, and relay protection, etc.

This product complies with the following standards:

GB20840.1-2010 "Transformers Part 1: General Technical Requirements"

GB20840.2-2014 "Transformers Part 2: Supplementary Technical Requirements for Current Transformers"

JJG313-2010 "Verification Regulations for Measuring Current Transformers"

Operating Environmental Conditions

1.Altitude: Not exceeding 1000 meters.

2.Ambient Temperature: -5°C to +40°C.

3.Relative Humidity: <85%.

4.Installation Location: Indoor.

Operational Parameters

1.Rated Secondary Current: 5A or 1A.

2.Power Factor: cosφ = -0.8 (lagging).

3.Rated Frequency: 50Hz or 60Hz.

4.Rated Primary Current, Rated Output, and Accuracy Class are shown in Table 1.

5.Insulation Performance: The primary winding to secondary winding and ground, and secondary winding to ground, can withstand a 3kV power-frequency withstand voltage for 1 minute.

Transformation Ratio Parameters

Model	Rated PrimaryCurrent (A)	Rated Output (VA)			Primary Turns
Model	Rated PrimaryCurrent (A)	0.2C Class	0.5C Class	1C Class	Primary Turns
LMZ1-0.5	5			5	30
	10				15
	15				10
	20	5	5		8
	30	5	5		5
	50				3
	75				2
	100				2
	100			5	1
	150-250	5	5	75
	300
	400
LMZ1(J)-0.5	500-800	10	10	15
	1000-1500	20	20	30
	2000-3000	20	20	30

Note: If the parameters required by the customer exceed the range shown in the table, they can be determined through consultation with our company.

Dimensions and Installation Size

Rated Primary Current (A)	H	h	ΦD	φd
5-250	115	68	90	30
300	118	70	93	36
400	120	70	93	46

Model Meaning

LXK- Φ(80、100、120、150、200、260)

Nominal Inner Hole Diameter

Open/Close Type

Zero Sequence

Current Transformer

Technical Parameters

Application	Zero Sequence ProtectionLXK-Φ(80、100、120、150、200、260)
Model
Transformation Ratio	Relay Model
60/1	DD-11/60	Series Connection	15x1	2.4-4.5
			30x1
		Parallel Connection	15x1	3-5
			30x2
	DD-11/60	Series Connection	15x1	3-5
			30x1
		Parallel Connection	15x2	3-5
			30x2

Application	Microcomputer Protection
Model	LXK-Φ(80、100、120、150、200、260)
Transformation Ratio	Accuracy Class	Rated Output
60/1	5P10	1
75/1	5P10	1.5
100/1	5P10	2.5
150/1	5P10	2.5
200/1	5P10	3.75
300/1	5P10	7.5
150/1	5P10	2.5
200/1	5P10	2.5
300/1	5P10	5
400/1	5P10	10
500/1	5P10	12.5
600/1	5P10	15

Overall & Mounting Bolt Dimension Figure

Cutout Device Drawing Of Inside Overpressur

Main Specifications, Enclosure&Installation Dimensions

Type	Rated Voltage R(kV)	ated frequency(Hz)	Rated output(kvar)	Ratedcapacitance (μF)	Rated curret (A)	DimensionΦ×H(mm)	MountingboltDimension (mm)
0.25-7.5-3N(1)	0.25	50	7.5	382.2	10.0 (30.0)	Φ76×240	M12×16
0.25-10-3N(1)	0.25	50	10	509.6	13.3 (40.0)	Φ86×240	M12×16
0.25-15-3N(1)	0.25	50	15	764.4	20.0 (60.0)	Φ106×280	M16×25
0.25-20-3N(1)	0.25	50	20	1019.1	26.7 (80.0)	Φ116×280	M16×25
0.25-25-3N(1)	0.25	50	25	1273.9	33.3 (100)	Φ136×280	M16×25
0.4-7.5-3(1)	0.4	50	7.5	149	10.8 (18.8)	Φ76×240	M12×16
0.4-10-3(1)	0.4	50	10	199	14.4 (25.0)	Φ76×240	M12×16
0.4-15-3(1)	0.4	50	15	299	21.7 (37.5)	Φ86×240	M16×25
0.4-20-3(1)	0.4	50	20	398	28.9 (50.0)	Φ116×240	M16×25
0.4-25-3(1)	0.4	50	25	498	36.1 (62.5)	Φ116×280	M16×25
0.4-30-3(1)	0.4	50	30	597	43.3 (75.0)	Φ116×280	M16×25
0.4-7.5-3(1)	0.45	50	7.5	118	9.6 (16.7)	Φ76×240	M12×16
0.4-10-3(1)	0.45	50	10	157	12.8 (22.2)	Φ76×240	M12×16
0.4-15-3(1)	0.45	50	15	236	19.2 (33.3)	Φ76×240	M16×25
0.4-20-3(1)	0.45	50	20	315	25.7 (44.4)	Φ106×240	M16×25
0.4-25-3(1)	0.45	50	25	393	35.1 (55.6)	Φ106×280	M16×25
0.4-30-3(1)	0.45	50	30	472	38.5 (66.7)	Φ116×280	M16×25
0.525-7.5-3(1)	0.525	50	7.5	87	8.2 (14.3)	Φ76×240	M12×16
0.525-10-3(1)	0.525	50	10	116	11.0 (19.0)	Φ76×240	M12×16
0.525-15-3(1)	0.525	50	15	173	16.5 (28.6)	Φ86×240	M16×25
0.525-20-3(1)	0.525	50	20	231	22.0 (38.1)	Φ106×280	M16×25
0.525-25-3(1)	0.525	50	25	289	27.5 (47.6)	Φ116×280	M16×25
0.525-30-3(1)	0.525	50	30	347	33.0 (57.1)	Φ136×280	M16×25

Note: Other specifications can be customized upon special order. The enclosure dimensions for single-phase capacitors are identical to those of three-phase capacitors with equivalent capacity. Values in parentheses refer to those of single-phase capacitors.

Model Meaning

EB 19 - □□/ □□

Number of auxiliary contacts, expressed as a number

20: Two normally open (NO) contacts and no normally closed (NC) contacts.

11: One normally open (NO) contact and one normally closed (NC) contact.

02: No normally open (NO) contacts and two normally closed (NC) contacts.(25A-43A)

21: Two normally open (NO) contacts and one normally closed (NC) contact.

12: One normally open (NO) contact and two normally closed (NC) contacts.(63A-95A)

Basic specification code, expressed in terms of conventional heating current

Design Code

AC Contactor

Scope of Application

The EB19 series capacitorswitchingcontactors (hereinafter referred to as "contactors") are primarily used in power circuits with a frequency of 50Hz or 60Hz and a rated operating voltage of up to 380v. They are designed for use in low-voltagereactive power compensation equipment to connect or disconnect lowvoltage parallel capacitors.

The contactors are equipped with an inrush current suppression device, which effectively minimizes the impact of closing inrush current on capacitors and suppresses overvoltage during disconnection.

Normal Working and Installation Conditions

3.1 Ambient Air Temperature:

The surrounding air temperature should be between -5°C and +40°C.

The average temperature within a 24-hour period must not exceed +35°C.

3.2 Altitude:

The installation altitude must not exceed 2000 meters.

3.3 Atmospheric Conditions:

At a maximum temperature of +40°C, the relative humidity must not exceed 50%.

Higher relative humidity is permitted at lower temperatures, e.g., 90% at 20°C.

Special precautions should be taken to prevent condensation caused by occasional temperature changes.

3.4 Pollution Degree:

The pollution degree is classified as Level 3.

3.5 Installation Category:

Installation category: Category III.

3.6 Installation Conditions:

The mounting surface should not be inclined more than ± 5 ^ { \circ } from the vertical plane.

3.7 Shock and Vibration:

The product should be installed and operated in locations free from significant shaking, impact, or vibration.

Figure 1

Contactormodel	Auxiliarycontact	Quantity		Label
Contactormodel	Auxiliarycontact	NO	NC	Label
EB19-25、32、43	20E	2	-	12, 14 23.24 -
	02E	-	2	- 11, 12 21, 22
	11E	1	1	13, 14 21,22
EB19-63、95	21E	2	1	13, 14 33.34 21,22
EB19-63、95	12E	1	2	13.14 21, 22 21, 22
EB19-115、150、170	10E	1	-	13.14 =
EB19-115、150、170	01E	-	1	- 11, 12

Main Parameters and Technical Performance

Parameter Name		EB19-25	EB19-32	EB19-43	EB19-63	EB19-95	EB19-115	EB19-150	EB19-170
Electrical Lifetime (10,000 times)		10	10	10	10	10	2	2	2
Rated Current le (380V) A		17	23	29	45	72	87	115	130
ControllableCapacitor CapacityCapacity (kvar)	220V	6	8	10	15	25	30	40	45
ControllableCapacitor CapacityCapacity (kvar)	380V	12	16	20	30	40	60	80	90
Rated Insulation Voltage (V)		660	660	660	660	660	1000	1000	1000
Inrush Current Suppression Capability		20le	20le	20le	20le	20le	20le	20le	20le
Operating Conditions		Pick-up voltage: (85%~110%) US; Drop-out voltage: (20%~75%)US
Coil Power (VA) - Inrush / Holding		70/8	110/11	110/11	200/20	200/20	300/22	300/22	300/22
Auxiliary Contacts for CapacitorSwitching (Contactor Control)		AC-15 360VA; DC-13 33W
Weight (kg)		0.57	0.57	0.6	1.25	1.5	2.3	2.3	2.3

Dimensions&Mounting Details

1.EB19-25, 32, 43 contactors can be installed with M4 screws and anti-loosening washers, or with 35mm mounting rails.

2.EB19-63, 95 contactors can be installed with M6 screws and anti-loosening washers, or with 35mm or 75mm mounting rails.

3. EB19-115, 150, 170 contactors can be installed with M6 screws and anti-loosening washers, or with two 35mm mounting rails, with a center distance of 100mm between the two rails.

4. The external dimensions and installation dimensions of EB19-25, 32, 43 are shown in Figure 2.

5. The external dimensions and installation dimensions of EB19-63, 95 are shown in Figure 3.

6. The external dimensions and installation dimensions of EB19-115, 150, 170 are shown in Figure 4.

Table 2

Dimensions&Mounting Details

Table 3 Table 4

Ordering Instructions

7.1 Order Details:

7.1.1 Complete Name and Model of the Contactor.

7.1.2 Rated Control Voltage and Frequency of the Coil.

7.1.3. Order quantity

7.2 Ordering Example:EB19-43/11 Switching capacitor contactor coil voltage 220V 50Hz 10 units

Model Meaning

EB W 5 - □- □ □ -□

Number of Output Circuits

S Sampling Signal - Three-Phase Sampling

Y Sampling Signal - Three-Phase Sampling

D DC 12V Voltage Output (Unlabeled) - Static Output

B Hole Dimensions: 162 x 102 mm, can replace JKG2B

C Hole Dimensions:113 x 113 mm

Design Serial Number and Feature Code

W Control Physical Quantity - Reactive Power

Low Voltage Reactive Power Automatic Compensation Controller

Main Purpose&Application Scope

EB series intelligent lowvoltage reactive power compensation controller (referred toas controller)is a special device for reactive power compensation in low voltage distribution system, designed according to the industry standard JB/T9663-1999 of the People's Republic of China and the power industry standard DL/T597-1996. Its sampled physical quantity is reactive power, with novel design, multiple functions, good controllability, high reliability and other advantages. It is in a leading position among similar products in China and provides a new equipment for distribution automation.

Operating Conditions

Power Supply Voltage:The rated supply voltage is AC 220V or 380V, with voltage fluctuations allowed up to +10%.

Ambient Temperature:The operating temperature range is -25°C to +55°C.

Relative Humidity:The maximum relative humidity allowed is 90% at 20°C.

Altitude:The device can be used at altitudes up to 2000 meters.

Environmental Conditions:The operating environment must be free of:

1.Explosive or flammable hazardous substances.

2.Corrosive gases that could damage the metal components.

3.Conductive dust that could damage the electrical insulation of the equipment.

Model Meaning

C K □ G

Dry-type (Self-cooling)

D = Single-phase S = Three-phase

Disturbance Generator

Series Connection

Product Overview

When capacitors are used for compensating capacitive reactive power, they are often affected by harmonic currents, inrush currents during switching, and operating overvoltage, which can lead to capacitor damage and a reduction in the power factor. To address this issue, it is necessary to install series reactors in front of the capacitors. These reactors serve to suppress and absorb harmonic waves, thereby protecting the capacitors from the detrimental effects of harmonic voltage and current surges. This improves power quality, enhances the system's power factor, and extends the service life of the capacitors.

Structural Features

Product Types:The product is available in both three-phase and single-phase versions, featuring a core-type design.

Core Material:The core is made of high-quality cold-rolled silicon steel sheets, processed using a high-speed punching press. The core is characterized by minimal burrs, uniform and orderly lamination, and an aesthetically neat appearance, ensuring the reactor operates with low temperature rise and low noise.

Coil Construction:The coils are made using high-quality insulated wire, wound by a dedicated machine, offering good flatness and a neat appearance.

Assembly Process:During the assembly process, all clamping parts undergo corrosion-resistant treatment. Critical clamping components are made of non-magnetic materials. The reactor undergoes a process of pre-baking,vacuum impregnation, and thermal curing, ensuring that the coils and core are securely bonded together. This significantly reduces temperature rise and noise during operation, effectively improving the reactor's quality factor and reducing harmonic effects. Compact Design:The reactor's external dimensions are designed to fit standard cabinet sizes, making it compact, easy to wire, and significantly reducing the cabinet cost investment for the user.

Performance Specifications and Technical Parameters

Applicable Capacitor Voltage:

The product can be used with capacitor voltages of 0.4kV, 0.45kV, 0.48kV, 0.525kV, 0.66kV, and 0.69kV. Inductive Reactance:

The reactance values are available in the following ranges: 1%, 6.67%, 6%, 7%, 12%, 13.8%, and 14%.

Voltage Withstand Rating:

The product has a voltage withstand rating of 5kV/min.

Insulation Class and Other Parameters:

The insulation grades available are Class B, Class F, and Class H.

Noise Level: ≤ 30dB.

Overload Capacity: The device can operate continuously with an overload capacity of up to 1.35 times its rated value.

Operating Environment

Altitude:The maximum altitude for operation is 2000 meters.

Operating Temperature and Humidity:The operating ambient temperature ranges from -25°C to +45°C, with a relative humidity of up to 90%.

Surrounding Environment:The environment should be free from harmful gases and flammable or explosive materials.

Ventilation Conditions:The environment should have good ventilation. If the equipment is installed inside a cabinet, ventilation devices should be added to ensureproper airflow.

Specifications of CKSG Series Low Voltage Three Phase Series Reactor

Capacity of matchedcapacitance (KVAR)	Capacity ofreactor (KVAR)	Model	Terminalcurrent (A)	OutlinedimensionLWH(mm)	Installationdimension (mm)	Insulation leve
	Reactance rate 6%
10	0.6	CKSG-0.6/0.45-6%	12.8	200125180	160*75	F/H
15	0.9	CKSG-0.9/0.45-6%	19.2	200125180	160*75	F/H
20	1.2	CKSG-1.2/0.45-6%	25.7	200135180	165*75	F/H
25	1.5	CKSG-1.5/0.45-6%	30.1	240155205	200*100	F/H
30	1.8	CKSG-1.8/0.45-6%	38.5	240160205	200*100	F/H
40	2.4	CKSG-2.4/0.45-6%	51.3	250170205	210*105	F/H
50	3.0	CKSG-3.0/0.45-6%	64.2	205175205	210*110	F/H
Reactance rate 7%
10	0.7	CKSG-0.7/0.45-7%	12.8	200125180	160*75	F/H
15	1.05	CKSG-1.05/0.45-7%	19.2	200125180	160*75	F/H
20	1.4	CKSG-1.4/0.45-7%	25.7	200135180	165*75	F/H
25	1.75	CKSG-1.75/0.45-7%	30.1	240155205	200*100	F/H
30	2.1	CKSG-2.1/0.45-7%	38.5	240160205	200*100	F/H
40	2.8	CKSG-2.8/0.45-7%	51.3	250170205	210*105	F/H
50	3.5	CKSG-3.5/0.45-7%	64.2	205175205	210*110	F/H
Reactance rate 12%
10	1.2	CKSG-1.2/0.525-12%	11	200125180	160*75	F/H
15	1.8	CKSG-1.8/0.525-12%	16.5	240160205	200*100	F/H
20	2.4	CKSG-2.4/0.525-12%	22	240170205	210*105	F/H
25	3.0	CKSG-3.0/0.525-12%	27.5	250175205	210*110	F/H
30	3.6	CKSG-3.6/0.525-12%	33	250175245	210*110	F/H
40	4.8	CKSG-4.8/0.525-12%	44	300190280	250*110	F/H
50	6.0	CKSG-6.0/0.525-12%	55	300190280	250*110	F/H
Reactance rate 14%
10	1.4	CKSG-1.4/0.525-14%	11	200125180	160*75	F/H
15	2.1	CKSG-2.1/0.525-14%	16.5	240160205	200*100	F/H
20	2.8	CKSG-2.8/0.525-14%	22	240170205	210*105	F/H
25	3.5	CKSG-3.5/0.525-14%	27.5	250175205	210*110	F/H
30	4.2	CKSG-4.2/0.525-14%	33	250175245	210*110	F/H
40	5.6	CKSG-5.6/0.525-14%	44	300190280	250*110	F/H
50	7.0	CKSG-7.0/0.525-14%	55	300190280	250*110	F/H

EBERRY ELECTRIC CO.,LTD.
Add: 66 pu nan Road, Yueqing Economic Development Zone, Zhejiang, China MP: 86-137 3677 9975
Email: sales@vcbbreaker.com
Wechat: 86-13983212540
Whatsapp:86-13736779975
Telegram:86-13983212540
Web:www.vcbbreaker.com

E-catalogue

ZALO