K13 or K13 Ultra Electric ScooterManual

1.The Scooter Parameters

Disclaimer:
Please abide by the relevant laws and regulations of the local bike ride，
The Company are not responsible to all the consequences of speeding up for perso nal reasons.
The fault status displays the area \mathsf { E } , when the symbol is flashing, press
the M/3 key to adjust the display interface to the E interface, the
corresponding number under the interface represents the
corresponding fault content, the specific status is as follows
E-001 Motor Hall fault
E-002 Handle failure
E-003 Controller failure
E-004 Brake failure
E-005 Voltage fault
E-006 Communication Failure (lnstrument Does Not Receive
Controller Signal)
E-007 Communication Failure (Controller Does Not Receive
Instrument Signal)

Wiring mode:

1. Red wire ( \mathsf { D } + ) : Positive input of power supply
2. Black wire (GND): Negative pole of power supply
3.Blue wire (DS): Controller switch lock
4.Green line (Tx): Communication transmission
5.Yellow line (RX): Communication reception
6. Grenade Hall Signal Station
Special note: The meter has Bluetooth,and has NFC function and password boot

This icon represents the NFC function)There are three options for P95 in the background of the instrument: 0 means no password and NFC swipe card to boot up, 1 means that only the NFC card can be used to boot the computer,and 2 means that the password and NFC swipe card can be turned on.The specific use is as follows:

1.When the background is set to O,you only need to press the boot button briefly to boot and use 2.When the background is set to 1,a letter N will appear above the instrument by pressing the power on button,which means that you want to swipe NFC to open the machine to turn on the phone, pay attention to the NFC card has a special card area, the meter has the word printed NFC, swipe the card in this area to boot the machine.

3.When the background is set to 2, N will appear on the meter by pressing the power on button

ENTER PASSWORD

and .If you want to use NFC to boot the same as the operation steps of item 2,if you choose the password to boot (when the instrument P96 is set to 2 the default password is 1234), directly enter the password 1234 (when choosing the password to boot, the first digit needs to long press the number after more than 1 second short press can be) according to the number button on the meter corresponding to the number can be turned on, here to remember that whether it is to boot with a password or NFC card to boot must complete the boot action within 5 seconds of short press the boot button,otherwise the instrument will automatically sleep, You need to press the power on button again to wake up the meter.

4. Bluetooth contact，downlaod APP ; Android users scan QR code and download.IPhone users directly search in the Iphone store

Open APP Will shows Click the Bluetooth icon to search for the Bluetooth name connection with the beginning of LIVlAE,and click the Bluetooth icon to jump to the login interface

If you don't want to register the binding, you can directly log in with the shortcut.Quick login cannot enter the instrument background to modify parameters:You need to register the binding to modify the parameters and prevent the vehicle from being abnormalized by misoperation.

How to register

--1.lick Register Account and enter the information according to the interface.

--2.After the information is registered, it will jump to the login interface and click Login.

--3.There will be this search Bluetooth interface,click on the name with LIVIAE at the beginning of the click, scan the code box,at this time directly scan the code or enter the barcode number and letter can be bound to enter the vehicle interface, the barcode is generally in the manual or the side of the instrument or the back of the instrument.

About NFC

1. Generally, there are 3 cards left the factory,and the blue one is the main card. The white one is the secondary card.

2. Blue main card: equivalent to the key is generally placed at home without a body, the main card can not play the role of booting,such as the white sub-card lost and you want to match the key is with a white sub-card,at this time you need a blue main card to match this key, equivalent to the blue main card is the master, the white sub-card for the guest, the guest wants to enter the door need the owner's consent.

3.Here explains how to use the blue main card, the premise P96 must be set to 1 or 2,short press the boot button (within 5 seconds) to swipe the blue main card in the NFC card area,at this time the number 1 will appear on the meter,when 1 appears to swipe the first white card,appear 2 to swipe the second card,when there is 3 you do not have the third white card casually in the swipe of a white card is completed,at this time the instrument will automatically shut down, each time the card will have a drop. Press the power on button to swipe the white card to turn on.

1. Short press the No.1 button to turn it on, and long press the No.1 button to shut down.

Press button 3 and button 5 at the same time to enter the background function layout:
P01: Backlight brightness,1-10
P02: Mileage unit, 0:km 1:mile,2:km mile full display
P03: Voltage level, 72V
P04: sleep time, O: no sleep Other numbers are sleep time, range: 1-60; Units in minutes
P06: Wheel: unit, inch; Accuracy: 0.1
P07: Measuring the number of magnets; Range: 1-100
P09: Zero start, non-zero boot setting, O: zero start; 1: Non-zero boot P10: Drive mode setting O assist drive; 1 Electric drive; 2 Power drive Electric drives coexist
P11: Assist sensitivity setting 1-24
P12: Starting torque: range: 0-5,0 weakest, 5 strongest
P13: Booster plate magnet type setting 5.8.12
P15: Motor drive signal percentage setting is set to 100 % full speed P16: Instrument real-time cruise function: O: No function 1: There is this function
P19: Taillight setting, O: Taillight is always on 1: Taillight is synchronized with headlights
P20: Boot Settings: 0: Soft Boot 1: Normal Boot ( 5 0 % ) 2: Hard Boot (100 % ）
P21: Electronic brake strength: O: none, 1 Yes (class 1-10)
P92: Handle Hallsetting: O; No rotary handlebar function, 1: There is a rotary handle function
P93: Change password: Press the number 3 button to change the password
P95: Boot mode: 0: No password /No NFC 1: There is NFC (Note: You can only boot with NFC. Pressing the boot button has no effect), 2: There is a password (4-digit password default 1234) / NFC
P96: Speed limit 40km setting: 0; The speed limit of 40km can not be canceled directly,1; long press No.3 to enter the speed limit of 40km/h can lift the speed limit of 40km, 2: long press the No.3 button can enter the speed limit of 40km/h can not be lifted, need to shut down in the boot to lift.
P97: Drive icon setting: 0 N o this function (can not switch single and

dual drives), 1: With this function (can switch single and dual drives); 2: The default is dual drive

P98: One-click start: O: No this feature,1 has this featureP99: One-key recovery (under the P99 parameter setting interface,long press the number 3 key for 5-6 seconds,all parameters are restored to the initial parameters of the instrument)

ODO:odo zero clearing (under the ODO parameter interface, first briefly press the No.3 button,and press and hold the No.3 button for 5-6 seconds until the digital clearance is released)

Operation Instructions

Press and hold the No.2 button

4
2

to turn on the headlights/long press to turn off the headlights at the

same time as the headlight icon

Follow the button to light up or turn off synchronously,and press the number 2 key to switch the start mode.

Long press button 3

SPORT COMFORT ECO PRO

Enter the speed limit and light up the speed limit icon,

Short press button 3

MODE 3

ODO/TRIP/TIME/fault code E/voltage V can be flipped

8888.8

Long press button 5

六

Light up the 6km humanoid icon

And turn on this function,and long press the No.5 button again You can cancel the pedestrian icon and return to the current gear.NO.4 buttom is

single/dual motor mode .Short press the No.4 button to switch various drive modes, such as the front-drive work icon

F

Rear drive working icon dual motors working icon

Short press button 5 is the gear, this button also works in a cycle,and the current maximum is 3 gears.

Press button 3 and button 5 at the same time to enter the background (after entering the background, you need to press the No.3 button shortly, when the number is flashing, you can modify the parameters through the No.4 button and the No.5 button. Short press the No.4 button Reduce 1,Short press button 5 can add 10.After adjusting the parameters you want, you need to long press the No.3 button Until the number does not flash,the setting is successful). After entering the background,when there is no modification of the parameters, the No.4 button and the No.5 button can be switched, P01-ODO can be used as the up-down button,and after the parameter adjustment, press No.3 and No.5 at the same time to return to the home page.

Set passport

ENTER PASSWORD 8888.8

ENTER PASSWORD

First of all, the factory with the default password (1234), elaborate: how to set the password into the background to select P95,here is an example to illustrate the choice 2,when we P95 choose 2 when the P93 function is turned on,and will produce an initial password 1234, let's talk about changing the password,when the password is set successfully want to change the password, adjust the parameters to P93 to see the factory password 1234,short press the No.3 button, this time the main interface iconStart to light up and stay on, iconThe number began to flash 4 horizontal bars,at this time enter the 4-digit password you want to decide,short press the number 3 button number number does not flash the iconlt means that the password has been set successfully,and so on if it needs to be changed again.When the P95 selects with password/NFC,every time the instrument is restarted, press the No. 1 button,and only this icon will appear on the main interface of the boot screenAnd the number becomes 4 horizontal bars, and the user needs to enter the correct password to restore the main interface (you need to press and hold when entering the first number, and the subsequent numbers do not need to) or directly use the NFC card to swipe the machine, the two coexist,which one is used first.

This is the icon that represents each different start mode, the factory defaultis ECO PRO for soft start energy-saving mode,you can set the default boot mode through the background, enter the background to select P20 to adjust 0 on behalf of ECO PRO,1 represents COMFORT,2 represents SPORT, during the driving process can be short press the No.2 button to switch various starting methods respectively, No.2 key is cyclic work, background P20 as the default boot choice.

The specified time of short press of the key is O.3 seconds,and the specified time of the long press of the key is 2 seconds

3.Charging

(1) Safe driving

In the acceleration or deceleration time,be aware to avoid the body's gravity in the h and,to avoid the body forward. The standing posture should be keeping your feet on e after the other, thus lead to more secure and stable riding.

A.When turning, the body is parallel to the handle. Please pay attention to the road condition before turning.Be sure it is safe and then turn. B.When the brakes,the gravity center of body backwards. It is better to learn to control the center of gravity when braking. Otherwise it will cause two situations: the car tilted forward,as well as brake and steering system damage.

(2) ChargingSteps.

(Very importand,pls as below steps to charging）1.Connect the cha

rgerto the scooter first.
2.Insert Plug the Electric City (110V -240V or OK).
3．the charger with green light is full charged, Red light is on charging.

1.When charging, please put safe place where children can not touch.
2.The red light indicates charging and the green light indicates charging is complete.
3. If you do not use it for a long time, charge it every 2 months.
4. Do not charge in a damp place.
5. Do not run the motor while charging.
6.Avoid contact with the material leak out of the battery accidentally.
7.Failure to store or recharge in accordance with the correct method may result in
damage to the battery and no charge.

4.Thewarrantyreference for Electric Scoote

Note:

Damage caused by human factors is not covered by the warranty. In the free warranty period, we do not charge maintenance fees. (Note: not include material costs) But the resulting transport costs borne by both parties.The company has the final interpretation.

User warranty card