FI08

三模（有线+2.4G+蓝牙）机械键盘 ThreeModular (wired+2.4G+Bluetooth) mechanical keyboard

产品手册 Productmanual

① 键盘指示灯② 接收器收纳仓④ 模式切换开关BT/有线/2.4G③ USB-C接口⑤ RGB氛围灯条及电量指示

·时尚的外观设计，108键布局，Gasket结构，PCB单键开槽，手感细腻软弹。
·键帽和机械开关可插拨，用户也可以购买市面上各品牌开关和个性化键帽自由DIY。
·键盘用料扎实，按键反应灵敏。
·独立收纳接收器。
·键盘人性化设计，与Fn配合增加一系列常用快捷功能按键。
·键盘蓝牙/2.4G/有线均支持全键无冲。

开关机说明

·将开关拨至有线(未插USB供电)，键盘即关机状态，内置电池停止对键盘供电。

·手动对码：长按3秒组合键“FN+\~”3秒左右，青色灯快闪进入对码状态，此时将接收器插入电脑USB端口，\~键青色灯亮2秒，2.4G连接成功。此时即完成对码。

注意:2.4G连接时先搜索再插接收器。出厂默认已对码。

① 切换至【BT】模式

② 按组合键切换至BT1， 约3S至蓝灯快闪进 入配对

③ 搜索配对名【AULA-F1083.0】 或【AULA-F1085.0】 连接成功蓝灯亮2秒后灭灯

·短按组合键Fn+数字1、2或3，蓝灯快闪，表示键盘进入对码或搜索模式，即可在设备中进行配对连接：回连状态下，为蓝灯亮2s。
·按Fn+数字键1、2、或3可以切换设备。

背光灯效调节

，配合驱动带音乐律动RGB灯效，此灯效下有10种灯效模式可选。

背光灯效快捷键调节

左 shift 切换RGB两侧氛 左 Alt 循环切换RGB两侧FN+ 左 灯条模式GB两侧 FN+ 氛围灯亮度氛围Ctrl Z氛围灯条速度 灯条颜色

右 切换RGB氛围灯 右 切换RGB氛围灯条↑shift AltFN+ 右 条模式 循环切换RGB氛围 FN+ 亮度 切换RGB氛围灯条Ctrl ？灯条速度 颜色

·Fn+WIN \ c = 锁定/解锁WIN键(在WIN系统下，锁定WIN键时指示灯常亮)WIN键无法使用)。指示灯：锁WIN键亮灯指示。·切换到Mac系统后左WIN/左ALT位置互换（不锁WIN）。

·按 F N + E S C 恢复出厂默认灯光模式，原来连接的蓝牙设备保存不会清除

F N + Q = Android系统（Q键红灯闪3s），F区单按功能与F区FN组合功能

F N + W = Windows系统（W键红灯闪3s），F区单按功能与F区FN组合功能

F N + E = Mac系统（E键红灯闪3s），F区单按功能与F区FN组合功能。

·无线对码时间，蓝牙-1分钟/2.4G-20S，超时未连接或无按键操作，则进休眠。回连时间，蓝牙-20S/2.4G-10S，超时未连接或无按键操作，则进休眠。无线连接后，一分钟无按键操作，则进休眠。休眠后，单击按键唤醒键盘。

·按住FN后可查看：

当前连接模式（2.4G、蓝牙、有线）；当前蓝牙通道(通道1、2、3)当前系统模式（安卓、win、Mac、IOS)
以上对应按键会亮灯，松开恢复灯效。
·2.4G模式指示灯 \dot { \mathbf { \eta } } = \mathbf { \eta } “\~”键
·有线模式指示灯 \mathbf { \bar { \rho } } = \mathbf { \rho } "4”键
·蓝牙通道指示灯 \mathbf { \bar { \rho } } = \mathbf { \rho } "1,2,3″键
·系统模式指示灯 \mathbf { \bar { \rho } } = \mathbf { \rho } "Q、W、E、R"键
·通过配备的USB线将键盘与电脑连接，即可为键盘充电。RGB氛围灯条可 F N + B 显示键盘电量，充电流光显示。充满长亮绿色，5个灯每个绿灯表示 20 % 电量。低电量全红指示。
： F N + B 进入电量模式。电量模式包含：电量显示及充电灯效显示。
·按 \mathsf { F N } + 左Shift退出电量模式，切回进入电量模式前的灯效。 F N + B 切到电量模式。
复位或重新上电，退出电量模式，执行正常灯效。
·USB-C连接性更可靠，性能更稳定，充电更快

A W充电说明

1、建议仅使用电脑USB接口对键盘进行充电；
2、请勿使用快充手机充电器对键盘充电；
3、请勿使用劣质非标电源适配器对键盘进行充电；
4、请勿使用过压过流电源适配器对键盘进行充电；
5、充电时请远离高温设备；
6、长时间不使用时请关闭电源开关。

以上充电说明同样适用于其他带充电功能设备(键盘/鼠标/耳机/音箱等）

·键数：108键
·FN键多功能
·产品尺寸： 4 4 5 . 1 7 x 1 3 8 . 8 9 x 4 1 . 3 5 ± 1 0 {mm }
·产品重量：约930g (不含线材/接收器)约978g (含线材/接收器)
·充电电压/电流：DC ⟨ 5 \mathsf { V } = 1 2 0 0 \mathsf { m A }
·额定电压：DC3.7V (充满4.2V)
·额定电流：约 2 0 0 { m A } @ 3 . 7 { v } (默认灯效）约20mA(关所有灯光)
·续航时间：约10小时 (默认灯效)约100小时 (关所有灯光)
·电池容量：4000mAh可充电锂电池
·充电接口：USB-C接口

·电脑系统需求:

有线/2.4G模式:WindowsALL操作系统WINXP,WIN7,WIN8,WIN10(在Win95，Win98系统下，可能需要驱动程序)。
有线模式/2.4G接收器：配置有USB1.1或以上版本端口。
蓝牙模式设备名称“AULAF1083.0”：WIN7及以下系统。
蓝牙模式设备名称“AULAF1085.0”：WIN8,WIN10及以上系统。蓝牙模式：带有蓝牙BT3.0，BLE4.0,BLE5.0及以上硬件的MAC电脑，Android手机或平板，IOS手机或平板。

·硬件连接有线USB/2.4G接收器支持热插拔（即插即用）。

尊敬的用户：

感谢您购买狼蛛系列产品！本质保卡是狼蛛产品的三包凭证，由用户自己保存，凭此质保卡您将享受狼蛛为您提供的产品售后服务。此质保卡每个产品一份，遗失不补，敬请妥善保管。

一、凭此卡您将享受以下权利与服务：

1、退货服务：自产品售出之日起七日内，产品出现质量问题，根据国家“三包服务“的规定，在产品外观与包装完整的情况下，将产品退还给销售商或者狼蛛指定地点，凭购买时的有效凭证，退回您支付的产品货款。

2、保修服务：自购买日起12月内出现产品性能故障情况经由狼蛛售后服务中心检测确定，可免费享受维修服务。

二、以下情况不属于免费服务范围：

1、超出规定的质保期限；

2、不能出示产品有效质保凭证或产品原序列号标签有涂改、替换、撕毁等现象的;
3、产品上没有序列号或质保凭证上的产品型号与产品实物不符的；
4、非正常使用、维护、保管所导致的故障和损坏；
5、非我公司授权的维修人员对产品修理、更改或拆卸而造成的故障或损坏；
6、意外事故或其他不可抗力造成的故障或损坏；
7、销售人员承诺的产品之外的服务及附加的配件或赠品不在本保修服务范围之列;
8、因电源、电压不稳而导致的故障或损坏。

维修记录：

① Keyboard indicator light ② Receiver storage compartment ③ USB-C interface ④ Mode switch BT/wired/2.4G ⑤ RGBambient light bar and battery indicator

· Stylish appearance design,108 key layout, gasket structure, PCB single key slot, delicate and soft touch.
· The keycaps and mechanical switches can be plugged in and unplugged,and users can also purchase various brands of switches and personalized keycaps on the market for free DIY.
· The keyboard is made of solid materials and has sensitive key response.
· Independent storage receiver.
· Humanized keyboard design,combined with Fn to add a series of commonly used shortcut function keys.
· Both keyboard Bluetooth/2.4G/wired support full key no collision.

① Switchto【wired】 mode

② Insertthe USB-C end of the standard USB cable into the corresponding port of the keyboard

③ Simply insertoneend of the USB cable into the computer's USB port

Power on/off instructions

· Turn the switch to wired (without USB power), the keyboard will be turned off, and the built-in battery will stop supplying power to the keyboard.

2.4G Connection Instructions

① Switchto【2.4G】mode ② Remove from the slot in theupperleft corner of the key【USB receiver】 ③ Simplyplugit into the USB port of the computerto use

Fn + Combination key for fast 2.4G code matching · Manual code matching: Press and hold the combination key " F N + ~ " for about 3 seconds, and the green light willflash to enter the code matching state.At this time, insert the receiver into the USB port of the computer,and the blue light of the \`\~key willight up for 2 seconds. The 2.4G connection is successful. At this point, the code matching is completed.

Attention: When connecting to 2 . 4 6 , search first and then plug in the receiver. The factory default code has been matched.

4G有线 设置 蓝牙 F CCD G 蓝牙 O 我的设备 ULA-F1083.0已 ① Switch to 【BT】 ② Pressthe combination ③ Searchforpairingname mode key to switch to BT1, 【AULA-F108 3.0】or and wait for about 3 【AULA-F108 5.0】 successfully seconds until the blue connected.The blue light will tu light flashes rapidly on for2 seconds and then turni to enter pairing

Combination key for quick device switching:

· Short press the combination key \mathsf { F n } + numbers1,2,or3,and the blue light will flash indicating that the keyboard has entered pairing or search mode,and can be paired a nd connected in the device.In the reconnection state, the blue light will light up for 2 seconds.
·Press Fn ^ + number keys 1 , 2 , or 3 to switch devices.

Backlight effect adjustment

· Cooperate with the driver to create music rhythm RGB lighting effects,which have 10 lighting modes to choose from.

Backlight effect shortcut key adjustment

Left Switch between RGB Left Cycletoswitchthe ↑shift ambient light bar Alt brightness of the RGB FN+ modes on both sides FN+ ambient light strips on Left Loop switching between Z Switch RGB ambient Ctrl RGB ambient light bar light bar colors on speedsonboth sides both sides

Right Switch RGB ambient Alt FN+ light bar brightness ? Switch RGB ambient light bar color

·Fn+WIN \ c = Lock/Unlock WIN key (in WIN system, the indicator light stays on when the WIN key is locked,and the WiN key cannot be used). Indicator light: Lock WiN key lights up to indicate.

， Switch to Mac system and swap the position of left WIN/left ALT (without locking WIN)

· Press F N + E S C to restore the factory default lighting mode,and the previously connected Bluetooth device will not be cleared.

F N + Q = Android system (Q key red light flashes for 3 seconds), F-zone single press function and F-zone FN combination function.

F N + W = Windows system (W key red light flashes for 3 seconds), F-zone single press function and F-zone FN combination function.

F N + E = Mac system (E key red light flashes for 3 seconds), F-zone single press function and F-zone FN combination function.。

·Wireless pairing time, Bluetooth -1 minute/2.4G-20s.If there is no connection or button
operation after timeout, it will enter sleep mode. Return time, Bluetooth -20S/2.4G-10S.If there is no connection or button operation after
timeout, it will enter sleep mode. After wireless connection,if there is no button operation for one minute, it will enter sleep mode. After hibernation, click the button to wake up the keyboard.

·Press and hold FN to view: Current connection mode (2.4G, Bluetooth,wired); Current Bluetooth channel (channels1,2, 3) Current system mode (Android,Windows,Mac, iOs) The corresponding buttons above willight up, release to restore the light effec · 2.4G mode indicator light \ c = "\~" key · Wired mode indicator light = " 4 " key ·Bluetooth channel indicator light \ c = "1,2, 3" keys · System mode indicator light \scriptstyle = " \mathsf { Q } , W, E, R" keys

·Connect the keyboard to the computer via the provided USB cable to charge the keyboard.The RGB ambient light bar can display keyboard battery level F N + B and charging streamer display. Full of continuous green light, with 5 lights each indicating （20 20 % battery life.Low battery all red indicator.
： F N + B enters battery mode.The power mode includes: power display and charging light effect display.
· Press F N + l .eft Shift to exit battery mode and switch back to the light effect before entering battery mode. F N + B switches to battery mode. Reset or power on again, exit battery mode,and perform normal lighting effects.
· USB-C connectivity is more reliable, performance is more stable,and charging is faster.
· Number of keys: 108 keys
·FN key multifunctional
·Product size: 4 4 5 . 1 7 x 1 3 8 . 8 9 x 4 1 . 3 5 ± 1 \mathsf {mm }
·Product weight: about 930g (excluding wire/receiver) About 978g (including cable/receiver)
· Charging voltage/current: DC 5 \mathsf { V } \equiv 1 2 0 0 \mathsf { m A } （204号
·Rated voltage: DC 3.7V (fully charged 4.2V)
·Rated current: about 2 0 0 { m A } \ @ \ 3 . 7 { v } (default light effect) About 20mA (turn off al lights)
·Battery life: about 1O hours (default light effect) About 10o hours (turn off all lights)
·Battery capacity: 40o0mAh rechargeable lithium battery
·Charging interface:USB-C interface
·Computer system requirements:

Wired/2.4G mode: Windows ALL operating system WIN XP,WIN7,WIN8, WIN10 In Win95 and Win98 systems, drivers may be required.
Wired mode/2.4G receiver: equipped with USB 1.1 or above ports.
Bluetooth mode device name "AULA F108 3.0":WiN7 and below systems.
Bluetooth mode device name "AULA F108 5.0": WIN8, WIN10 and above systems. Bluetooth mode: MAC computers, Android phones or tablets, IOS phones or tablet with Bluetooth BT3.0, BLE4.0, BLE5.0 and above hardware.

·Hardware connection The wired USB/2.4G receiver supports hot plugging (plug and play).

Dear Customer:

Thank you for purchasing AULA series products! This warranty card is the proof of AULA products,which is kept by the user,with this warranty card you will enjoy the after-sales service provided by AULA. This warranty card is a copy of each product and will not be replaced if lost, so please keep it in a safe place.

I. With this card you will enjoy the following rights and services: 1.Return service: within seven days from the date of sale of the product, the product quality problems, according to the provisions of the national "three packages", in the case of the product appearance and packaging intact, the product will be returned to the seller or tarantula designated places,with the purchase of the valid certificate, return the product you paid for the purchase price. 2.Warranty service: If the product performance failure is detected by AULA after-sales service center within 12 months from the date of purchase, you can enjoy the maintenance service free of charge.

Ⅱ.The following situations do not belong to the free service scope:
1. Exceeding the specified warranty period;
2. Cannot show the valid warranty certificate or the original serial number label has been altered, replaced, torn and other phenomena;
3.There is no serial number on the product or the product model on the warranty certificate does not match the product in kind;
4.Failure and damage caused by abnormal use, maintenance and storage;
5.Failure or damage caused by repair, change or disassembly of the product by non-authorized maintenance personnel of our company;
6.Failure or damage caused by accidents or other force majeure;
7. Services and additional accessories or gifts outside the product promised by the sales staff are not included in the scope of this warranty service;
8. Failure or damage caused by unstable power supply or voltage.

sales record:

Repair Record:

ShenzhenSuoai ElectroniceCo.,Ltd深圳市索艾电子科技有限公司

Commissioned Manufacturer:
Dongguan Suoai Electronice Co., Ltd
委托制造商：东莞市索艾电子科技有限公司
SOAI Industry Park, Huayu Street ChanglongVillage Huangjiang Town Dongguan City
Guangdong Province.
广东省东莞市黄江镇长龙村华裕街 索艾产业园