该页无缩略图
三相异步电动THREE-PHASE ASYNCHRONOUS MOTOR
产品展示PRODUCTEXHIBITION
目 录CONTENTS
Y2系列(IP54)三相异步电动机
Y2SERIES(IP)THREE-PHASE
ASYNCHRONOUS MOTOR 295-303
YS系列(IP54)小功率三相异步电动机
YSSERIES(IP54)SMALL POWER THREE-PHASE
ASYNCHRONOUS MOTOR P304-305
Y2EJ系列(IP54)电磁制动三相异步电动机
Y2EJ SERIES(IP54)ELECTROMAGNETIC BRAKE
THREE-PHASE ASYNCHRONOUS MOTOR…………………………………………P306-312
YVF2系列(IP54)变频调速三相异步电动机
YVF2SERIES(IP54)FREQUENCY VARIABLE SPEED REGULATION
THREE-PHASE ASYNCHRONOUS MOTOR…………………………………………………P313-318
YD系列(IP54)变极多速三相异步电动机
YD SERIES(IP54)ELECTROOE-VARIED MULTI-SPEED
THREE-PHASE ASYNCHRONOUS MOTOR………………………………………………………P319-326
配硬齿面减速机专用电机外形尺寸
DIMENSION OF SPECIAL MOTOR FOR
SPEED REDUCING MACHINE……P327-329
电机常见故障及排除方法
FREQUENT MALFUNCTIONS AND SOLUTIONS ………………………………………………P330-330
Y2系列(IP54)三相异步电动机
产品概述
Y系列(IP54)三相异步电动机是我国集国际工业发达国家先进经验而开发设计的最新一代三相异步电动机产品。各项性能指标达到国际90年代的先进水平。执行标准是JB/T8680-2008《Y2系列(IP54)三相异步电动机技术条件》。
Y2系列(IP54)三相异步电动机机座号从63到355共计15个机座号，极数有2极、4极、6极、8极、10极、功率从0.12kw到315kw共计117个规格。
本厂目前生产的有63-315共14个机座号，有2极、4极、6极、8极、10极、功率从0.12到200kw，共计104个规格。
(一)、Y2系列(IP54)三相异步电动机的特点：
1、本系列电动机标准化、通用化程度高，安装尺寸与Y系列同规格电动机基本上相同，具有一定的继承性。标准件、紧固件等均按国内有关标准选用。
2、电动机具有独特的外形结构——平行垂直散热片，既增加了散热面积，又增强了电动机的美感。
3、绝缘等级为F级，但温升考核仍按B级标准考核，既增加了电动机的使用可靠性，又提高了使用寿命。
4、振动小，噪声低。
5、负载率在75%左右时具有最佳效率特点。
(二)、Y2系列(IP54)三相异步电动机的使用条件：
1、环境温度不超过40℃，不低于一15℃；
2、月平均最高相对湿度不超过90%，同时该月月平均温度不高于25℃;
3、海拔高度不超过1000m；
4、额定频率为50HZ;
5、额定电压为380V;
6、工作制为S，（连续工作制）；
7、冷却方式为IC0141（风扇自扇冷却）；
8、接法：功率在3kw(4hp)及以下者为"Y"接，功率在4KW(5.5hp)及以上者为“△”接。
Y2series(IP54)three-Phase asynchronous motor
Brief introduction of the enterprise
Y2(IP54)three-phase asynchronous motor is the latest three-phase asynchronous motor developed by finalizing the advanced experiences from international developed countries,various properties have reached the international advanced standard in 1990.The performing standards are conformed to JB/T8680-2008《Yseries(IP54)three-phase asynchronous motor's technical conditions》。
For Y series (IP54)three-phase asynchronous motor the frame number is 63-315 total 14 frame numbers,the electrode reach2,4,8,10,power from 0.12 to200Kw, Totally 104 specifications.
At present we produced 82 specifications,from frame number 63 to 280, The number of electrode range include 2,4,6,8,and power range from 0.12 to 200kw.
(1)Characteristics of Y2(IP54)three-phase asynchronous motor:
1.High standardization and universal of this series,The install size is basicly similar to Y series motor in the same specification. The standard parts and fasteners are choosed according to relevant national standards.
2. Y series(IP54) electrical motor adopts special exterior design—paralles & vertical radiate slices·This design not only increased radiate surface but also strengthened the electric motor's beautification.
3、Y, series(IP54)motor insulation degree is F grade,but for the temperature rise,we still use B grade standard,those increase both reliability and exterd.
4、Y series(IP54)motor has low vibrancy and low noise.
(2)Y2series (IP54)three-phase asynchronous motor's application conditions:
1. The ambient temperature shouldn't surpass 40C, and not lower than-15℃.
2、 Average maximum relative humidity should not be over 90% per month. The average temperature within a month should not be over 25℃.
3、Elevation shouldn't surpass 1000 metres.
4、Rating frequency is 50HZ.
5、Rating voltage is 380V.
6.Work system is S,(continuing work system).
7. Cooling mode is IC0141(fan cooling).
8. connection method:For those that the power is lower that 3Kw(4hp)adopt'Y"connection, and for those that the power is higher that 4Kw(5.5Hp)adopt:“△”connection.
| 型号Type | 额定功率Output power | 满载时Full loaded | 麟unloadedvibration(mm/s) | 空载噪声unloadedNoisedB(A) | 负载噪声loadedNoisedb(A) | 堵转电流额定电流LockedtFullload(muple)V | 堵转转矩额定转矩LockedLoFull load(mmple)9 | 最大转矩额定转矩MaxtorqueFullloadtorque(倍multiple)e) | ||||
| (KW) | (HP) | 异步转速AsinciomousSpeed(r/min) | 电流Current(A) | 效率Eff(%) | 功率新rfactor(COS φ) | |||||||
| 同步转速 3000r/min(2极)380V50HzSynchronous Speed 3000r/min(2P)380V 50HZ | ||||||||||||
| Y-63M,-2 | 0.18 | 0.24 | 2800 | 0.53 | 65 | 0.80 | 1.8 | 61 | 63 | 5.5 | 2.2 | 2.2 |
| Y,-63M,-2 | 0.25 | 0.34 | 2800 | 0.69 | 68 | 0.81 | 1.8 | 61 | 63 | 5.5 | 2.2 | 2.2 |
| Y2-71M,-2 | 0.37 | 0.50 | 2800 | 0.99 | 70 | 0.81 | 1.8 | 64 | 66 | 6.1 | 2.2 | 2.2 |
| Y-71M2-2 | 0.55 | 0.75 | 2800 | 1.40 | 73 | 0.82 | 1.8 | 64 | 66 | 6.1 | 2.2 | 2.3 |
| Y2-80M.-2 | 0.75 | 1 | 2840 | 1.83 | 75 | 0.83 | 1.8 | 67 | 69 | 6.1 | 2.2 | 2.3 |
| Y,-80M,-2 | 1.1 | 1.5 | 2840 | 2.60 | 76.2 | 0.84 | 1.8 | 67 | 69 | 7.0 | 2.2 | 2.3 |
| Y-90S-2 | 1.5 | 2 | 2840 | 3.50 | 78.5 | 0.84 | 1.8 | 72 | 74 | 7.0 | 2.2 | 2.3 |
| Y,-90L-2 | 2.2 | 3 | 2840 | 4.90 | 81 | 0.85 | 1.8 | 72 | 74 | 7.0 | 2.2 | 2.3 |
| Y-100L-2 | 3 | 4 | 2860 | 6.30 | 82.6 | 0.87 | 1.8 | 76 | 78 | 7.5 | 2.2 | 2.3 |
| Y-112M-2 | 4 | 5.5 | 2890 | 8.20 | 84.2 | 0.88 | 1.8 | 77 | 79 | 7.5 | 2.2 | 2.3 |
| Y,-132S,-2 | 5.5 | 7.5 | 2900 | 11.1 | 85.7 | 0.88 | 1.8 | 80 | 82 | 7.5 | 2.2 | 2.3 |
| Y_-132S,-2 | 7.5 | 10 | 2900 | 14.9 | 87 | 0.88 | 1.8 | 80 | 82 | 7.5 | 2.2 | 2.3 |
| Y,-160M,-2 | 11 | 15 | 2947 | 21.2 | 88.4 | 0.89 | 2.8 | 86 | 88 | 7.5 | 2.2 | 2.3 |
| Y-160M.-2 | 15 | 20 | 2947 | 28.6 | 89.4 | 0.89 | 2.8 | 86 | 88 | 7.5 | 2.2 | 2.3 |
| Y-160L-2 | 18.5 | 25 | 2947 | 34.7 | 90 | 0.90 | 2.8 | 86 | 88 | 7.5 | 2.2 | 2.3 |
| Y2-180M-2 | 22 | 30 | 2930 | 41 | 90.5 | 0.90 | 2.8 | 89 | 91 | 7.5 | 2.2 | 2.3 |
| Y2-200L,-2 | 30 | 40 | 2940 | 55.4 | 91.4 | 0.90 | 2.8 | 92 | 94 | 7.5 | 2.2 | 2.3 |
| Y-200L2-2 | 37 | 50 | 2940 | 67.9 | 92 | 0.90 | 2.8 | 92 | 94 | 7.5 | 2.2 | 2.3 |
| Y2-225M-2 | 45 | 60 | 2970 | 82.1 | 92.5 | 0.90 | 3.5 | 92 | 94 | 7.5 | 2 | 2.3 |
| Y2-250M-2 | 55 | 74 | 2970 | 99.8 | 93 | 0.90 | 3.5 | 93 | 95 | 7.5 | 2 | 2.3 |
| Y-280S-2 | 75 | 100 | 2970 | 135.3 | 93.6 | 0.90 | 3.5 | 94 | 96 | 7.5 | 2 | 2.3 |
| Y2-280M-2 | 90 | 121 | 2970 | 160 | 93.9 | 0.91 | 3.5 | 94 | 96 | 7.5 | 2 | 2.3 |
| Y-315S-2 | 110 | 147 | 2982 | 195.4 | 94 | 0.91 | 3.5 | 96 | 98 | 7.1 | 1.8 | 2.2 |
| Y2-315M-2 | 132 | 177 | 2982 | 233.2 | 94.5 | 0.91 | 3.5 | 96 | 98 | 7.1 | 1.8 | 2.2 |
| Y2-315L,-2 | 160 | 214 | 2982 | 279.3 | 94.6 | 0.92 | 3.5 | 99 | 101 | 7.1 | 1.8 | 2.2 |
| Y-315L-2 | 200 | 268 | 2982 | 348.4 | 94.8 | 0.92 | 3.5 | 99 | 101 | 7.1 | 1.8 | 2.2 |
| 型号Type | 额定功率Output power | 满载时Full loaded | unloadedvibration(mm/s) | 空载噪声unloadedNoisedB(A) | 负载噪声loadedNoisedb(A)) | 堵转电流额定电流Lockedtt | 堵转转矩额定转矩Lockedrotortorque | 最大转矩额定转矩Maxtorque | ||||
| (KW) | (HP) | 异步转速AsynchromiousSpeed(r/min) | 电流Current(A) | 效率Eff(%) | 功率因数Powerfactor(COS φ) | |||||||
| Fullload(muemtlee)1-1 | Full load(ple) | Fullloadtorque(倍multiple) | ||||||||||
| 同步转速 1500r/min(4极)380V 50HzSynchronous Speed 1500r/min(4P)380V 50HZ | ||||||||||||
| Y2-63M,-4 | 0.12 | 0.16 | 1330 | 0.44 | 57 | 0.72 | 1.8 | 52 | 57 | 4.4 | 2.1 | 2.2 |
| Y₂-63M-4 | 0.18 | 0.24 | 1330 | 0.62 | 60 | 0.73 | 1.8 | 52 | 57 | 4.4 | 2.1 | 2.2 |
| Y2-71M,-4 | 0.25 | 0.34 | 1350 | 0.79 | 65 | 0.74 | 1.8 | 55 | 60 | 5.2 | 2.1 | 2.2 |
| Y2-71M2-4 | 0.37 | 0.5 | 1350 | 1.12 | 67 | 0.75 | 1.8 | 55 | 60 | 5.2 | 2.1 | 2.2 |
| Y2-80M,-4 | 0.55 | 0.75 | 1380 | 1.57 | 71 | 0.75 | 1.8 | 58 | 63 | 5.2 | 2.4 | 2.3 |
| Y2-80M2-4 | 0.75 | 1 | 1380 | 2.05 | 73 | 0.76 | 1.8 | 58 | 63 | 6.0 | 2.3 | 2.3 |
| Y,-90S-4 | 1.1 | 1.5 | 1390 | 2.8 | 76.2 | 0.77 | 1.8 | 61 | 66 | 6.0 | 2.3 | 2.3 |
| Y₂-90L-4 | 1.5 | 2 | 1390 | 3.7 | 78.5 | 0.79 | 1.8 | 61 | 66 | 6.0 | 2.3 | 2.3 |
| Y2-100L,-4 | 2.2 | 3 | 1410 | 5.1 | 81 | 0.81 | 1.8 | 64 | 69 | 7.0 | 2.3 | 2.3 |
| Y2-100L2-4 | 3 | 4 | 1410 | 6.7 | 82.6 | 0.82 | 1.8 | 64 | 69 | 7.0 | 2.3 | 2.3 |
| Y_-112M-4 | 4 | 5.5 | 1440 | 8.8 | 84.2 | 0.82 | 1.8 | 65 | 70 | 7.0 | 2.3 | 2.3 |
| Y-132S-4 | 5.5 | 7.5 | 1450 | 11.7 | 85.7 | 0.83 | 1.8 | 71 | 76 | 7.0 | 2.3 | 2.3 |
| Y-132M-4 | 7.5 | 10 | 1450 | 15.6 | 87 | 0.84 | 1.8 | 71 | 76 | 7.0 | 2.3 | 2.3 |
| Y-160M-4 | 11 | 15 | 1460 | 22.5 | 88.4 | 0.84 | 2.8 | 75 | 80 | 7.0 | 2.2 | 2.3 |
| Y2-160L-4 | 15 | 20 | 1460 | 30.0 | 89.4 | 0.85 | 2.8 | 75 | 79 | 7.5 | 2.2 | 2.3 |
| Y,-180M-4 | 18.5 | 25 | 1470 | 36.3 | 90 | 0.86 | 2.8 | 76 | 80 | 7.5 | 2.0 | 2.3 |
| Y-180L-4 | 22 | 30 | 1470 | 42.9 | 90.5 | 0.86 | 2.8 | 76 | 80 | 7.5 | 2.0 | 2.3 |
| Y-200L-4 | 30 | 40 | 1470 | 58 | 91.4 | 0.86 | 2.8 | 79 | 83 | 7.5 | 2.0 | 2.3 |
| Y_-225S-4 | 37 | 50 | 1480 | 70.2 | 92 | 0.87 | 3.5 | 81 | 85 | 7.2 | 2.2 | 2.3 |
| Y-225M-4 | 45 | 60 | 1480 | 85 | 92.5 | 0.87 | 3.5 | 81 | 84 | 7.2 | 2.2 | 2.3 |
| Y-250M-4 | 55 | 74 | 1480 | 103.3 | 93 | 0.87 | 3.5 | 83 | 86 | 7.2 | 2.2 | 2.3 |
| Y-280S-4 | 75 | 100 | 1480 | 139.9 | 93.6 | 0.87 | 3.5 | 86 | 89 | 7.2 | 2.2 | 2.3 |
| Y2-280M-4 | 90 | 121 | 1480 | 167.4 | 93.9 | 0.87 | 3.5 | 86 | 89 | 7.2 | 2.2 | 2.3 |
| Y,-315S-4 | 110 | 147 | 1486 | 201.0 | 94.5 | 0.88 | 3.5 | 93 | 96 | 6.9 | 2.1 | 2.2 |
| Y2-315M-4 | 132 | 177 | 1486 | 240.4 | 94.8 | 0.88 | 3.5 | 93 | 96 | 6.9 | 2.1 | 2.2 |
| 型号Type | 额定功率Output power | 满载时Full loaded | unloadedvibration(mm/s) | 空载噪声unloadedNoisedB(A) | 负载噪声loadedNoisedb(A)) | 堵转电流额定电流Lockedunt | 堵转转矩额定转矩LockedLU | 最大转矩额定转矩Maxtorque | ||||
| (KW) | (HP) | 异步转速AsynciomousSpeed(r/min) | 电流Current(A) | 效率Eft(%) | 功率新rfactor(COS φ) | |||||||
| Full load(mutple)e) | Full load(lple)raue | Full load(倍muitiple)torque | ||||||||||
| Y-315L,-4 | 160 | 214 | 1486 | 287.8 | 94.9 | 0.89 | 3.5 | 97 | 100 | 6.9 | 2.1 | 2.2 |
| Y_2-315L-4 | 200 | 268 | 1486 | 359.8 | 94.9 | 0.89 | 3.5 | 97 | 100 | 6.9 | 2.1 | 2.2 |
| 同步转速 1000r/min(6极)380V 50HzSynchronous Speed 1000r/min(6P)380V 50HZ | ||||||||||||
| Y,-71M,-6 | 0.18 | 0.25 | 850 | 0.74 | 56 | 0.66 | 1.8 | 52 | 59 | 4.0 | 1.9 | 2.0 |
| Y_-71M2-6 | 0.25 | 0.34 | 850 | 0.95 | 59 | 0.68 | 1.8 | 52 | 59 | 4.0 | 1.9 | 2.0 |
| Y,-80M,-6 | 0.37 | 0.50 | 885 | 1.30 | 62 | 0.70 | 1.8 | 54 | 61 | 4.7 | 1.9 | 2.0 |
| Y,-80M,-6 | 0.55 | 0.75 | 885 | 1.79 | 65 | 0.72 | 1.8 | 54 | 61 | 4.7 | 1.9 | 2.1 |
| Y2-90S-6 | 0.75 | 1 | 910 | 2.29 | 69 | 0.72 | 1.8 | 57 | 64 | 5.5 | 2.0 | 2.1 |
| Y-90L-6 | 1.1 | 1.5 | 910 | 3.2 | 72 | 0.73 | 1.8 | 57 | 64 | 5.5 | 2.0 | 2.1 |
| Y-100L-6 | 1.5 | 2 | 920 | 4.0 | 76 | 0.75 | 1.8 | 61 | 68 | 5.5 | 2.0 | 2.1 |
| Y-112M-6 | 2.2 | 3 | 940 | 5.60 | 79 | 0.76 | 1.8 | 65 | 72 | 6.5 | 2.0 | 2.1 |
| Y2-132S-6 | 3 | 4 | 960 | 7.40 | 81 | 0.76 | 1.8 | 69 | 76 | 6.5 | 2.1 | 2.1 |
| Y,-132M,-6 | 4 | 5.5 | 960 | 9.8 | 82 | 0.76 | 1.8 | 69 | 76 | 6.5 | 2.1 | 2.1 |
| Y-132M2-6 | 5.5 | 7.5 | 960 | 12.9 | 84 | 0.77 | 1.8 | 69 | 76 | 6.5 | 2.1 | 2.1 |
| Y-160M-6 | 7.5 | 10 | 960 | 17.2 | 86 | 0.77 | 2.8 | 73 | 80 | 6.5 | 2.0 | 2.1 |
| Y,-160L-6 | 11 | 15 | 960 | 24.5 | 87.5 | 0.78 | 2.8 | 73 | 80 | 6.5 | 2.0 | 2.1 |
| Y-180L-6 | 15 | 20 | 970 | 31.6 | 89 | 0.81 | 2.8 | 73 | 79 | 7.0 | 2.0 | 2.1 |
| Y-200L,-6 | 18.5 | 25 | 970 | 38.6 | 90 | 0.81 | 2.8 | 76 | 82 | 7.0 | 2.1 | 2.1 |
| Y-200L₂-6 | 22 | 30 | 970 | 44.7 | 90 | 0.83 | 2.8 | 76 | 82 | 7.0 | 2.1 | 2.1 |
| Y2-225M-6 | 30 | 40 | 980 | 59.3 | 91.5 | 0.84 | 3.5 | 76 | 82 | 7.0 | 1.8 | 2.1 |
| Y-250M-6 | 37 | 49.6 | 980 | 71.1 | 92 | 0.86 | 3.5 | 78 | 84 | 7.0 | 1.8 | 2.1 |
| Y-280S-6 | 45 | 60 | 980 | 85.9 | 92.5 | 0.86 | 3.5 | 80 | 85 | 7.0 | 1.8 | 2.0 |
| Y,-280M-6 | 55 | 74 | 980 | 104.7 | 92.8 | 0.86 | 3.5 | 80 | 85 | 7.0 | 1.8 | 2.0 |
| Y_-280S-6 | 75 | 100 | 987 | 141.7 | 93.5 | 0.86 | 3.5 | 85 | 89 | 7.0 | 2.0 | 2.0 |
| Y2-280M-6 | 90 | 120 | 987 | 169.5 | 93.8 | 0.86 | 3.5 | 85 | 89 | 7.0 | 2.0 | 2.0 |
| Y-180L-6 | 110 | 147 | 987 | 206.7 | 94 | 0.86 | 3.5 | 85 | 89 | 6.7 | 2.0 | 2.0 |
| Y-200L,-6 | 132 | 177 | 987 | 244.7 | 94.2 | 0.87 | 3.5 | 85 | 89 | 6.7 | 2.0 | 2.0 |
| 型号Type | 额定功率Output power | 满载时Full loaded | unloadedvibration(mm/s) | unloadedNoisedB(A) | 负载噪声loadedNoisedb(A) | 堵转电流额定电流LockedrotorcuentFull load(mumpee) | 堵转转矩额定转矩LockedrotortorqueFull load)(倍mrlpl)(( | 最大转矩额定转矩MaxtorquieFull loadtorque(倍multiple) | ||||
| (KW) | (HP) | 异步转速AsyncroiousSpeed(r/min) | 电流Current(A) | 效率Eff(%) | r功率factor(cOS φ) | |||||||
| 同步转速750r/min(8极)380V 50HzSynchronous Speed 750r/min(8P)380V 50HZ | ||||||||||||
| Y-80M,-8 | 0.18 | 0.25 | 645 | 0.88 | 51 | 0.61 | 1.8 | 52 | 60 | 3.3 | 1.8 | 1.9 |
| Y,-80M2-8 | 0.25 | 0.34 | 645 | 1.15 | 54 | 0.61 | 1.8 | 52 | 60 | 3.3 | 1.8 | 1.9 |
| Y-90S-8 | 0.37 | 0.5 | 670 | 1.49 | 62 | 0.61 | 1.8 | 56 | 64 | 4.0 | 1.8 | 1.9 |
| Y,-90L-8 | 0.55 | 0.75 | 670 | 2.17 | 63 | 0.61 | 1.8 | 56 | 64 | 4.0 | 1.8 | 2.0 |
| Y-100L,-8 | 0.75 | 1 | 680 | 2.4 | 71 | 0.67 | 1.8 | 59 | 67 | 4.0 | 1.8 | 2.0 |
| Y2-100L2-8 | 1.1 | 1.5 | 680 | 3.3 | 73 | 0.69 | 1.8 | 59 | 67 | 5.0 | 1.8 | 2.0 |
| Y2-112M-8 | 1.5 | 2 | 690 | 4.4 | 75 | 0.69 | 1.8 | 61 | 69 | 5.0 | 1.8 | 2.0 |
| Y2-132S-8 | 2.2 | 3 | 710 | 6.0 | 78 | 0.71 | 1.8 | 64 | 72 | 6.0 | 1.8 | 2.0 |
| Y-132M-8 | 3 | 4 | 710 | 7.9 | 79 | 0.73 | 1.8 | 64 | 72 | 6.0 | 1.9 | 2.0 |
| Y-160M,-8 | 4 | 5.5 | 720 | 10.3 | 81 | 0.73 | 2.8 | 68 | 76 | 6.0 | 1.9 | 2.0 |
| Y,-160M,-8 | 5.5 | 7.5 | 720 | 13.6 | 83 | 0.74 | 2.8 | 68 | 76 | 6.0 | 2.0 | 2.0 |
| Y-160L-8 | 7.5 | 11 | 720 | 17.8 | 85.5 | 0.75 | 2.8 | 68 | 76 | 6.0 | 2.0 | 2.0 |
| Y-180L-8 | 11 | 15 | 730 | 25.1 | 87.5 | 0.76 | 2.8 | 70 | 78 | 6.6 | 2.0 | 2.0 |
| Y,-200L-8 | 15 | 20 | 730 | 34.1 | 88.0 | 0.76 | 2.8 | 73 | 80 | 6.6 | 2.0 | 2.0 |
| Y-225S-8 | 18.5 | 25 | 730 | 41.1 | 90 | 0.76 | 3.5 | 73 | 80 | 6.6 | 1.9 | 2.0 |
| Y-225M-8 | 22 | 30 | 740 | 47.4 | 90.5 | 0.78 | 3.5 | 73 | 80 | 6.6 | 1.9 | 2.0 |
| Y-250M-8 | 30 | 40 | 740 | 63.4 | 91 | 0.79 | 3.5 | 75 | 82 | 6.6 | 1.9 | 2.0 |
| Y2-280S-8 | 37 | 50 | 740 | 77.8 | 91.5 | 0.79 | 3.5 | 76 | 83 | 6.6 | 1.9 | 2.0 |
| Y2-280M-8 | 45 | 60 | 740 | 94.1 | 92 | 0.79 | 3.5 | 76 | 82 | 6.6 | 1.9 | 2.0 |
| Y2-315S-8 | 55 | 74 | 740 | 111.2 | 92.8 | 0.81 | 3.5 | 82 | 88 | 6.6 | 1.8 | 2.0 |
| Y-315M-8 | 75 | 100 | 740 | 151.3 | 93 | 0.81 | 3.5 | 82 | 88 | 6.6 | 1.8 | 2.0 |
| Y_-315L,-8 | 90 | 120 | 740 | 177.8 | 93.8 | 0.82 | 3.5 | 82 | 88 | 6.6 | 1.8 | 2.0 |
| Y-315L2-8 | 110 | 147 | 740 | 216.8 | 94 | 0.82 | 3.5 | 82 | 88 | 6.4 | 1.8 | 2.0 |
机座不带底脚，端盖上有凸缘(带通孔)-IMB5
Frame without feet and end-shield with flange(with plain holes)-IMB5
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 凸缘号Frangecode | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number ofpoles on theflange | 外型尺寸Exterior dimension(mm) | ||||||||||||||
| D | E | F | G | M | N | P | R | s | T | AC | AD | HF | L | ||||||
| 63M | FF115 | 2、4 | 11 | 23 | 4 | 8.5 | 115 | 95 | 140 | 10 | 3 | 4 | 130 | 110 | 180 | 230 | |||
| 71M | FF130 | 2、4、6 | 14 | 30 | 5 | 11 | 130 | 110 | 160 | 3.5 | 145 | 120 | 200 | 255 | |||||
| 80M | FF165 | 19 | 40 | 6 | 15.5 | 165 | 130 | 200 | 12 | 175 | 130 | 230 | 295 | ||||||
| 90S | 24 | 50 | 8 | 20 | 195 | 140 | 240 | 320 | |||||||||||
| 90L | 345 | ||||||||||||||||||
| 100L | FF215 | 28 | 60 | 24 | 215 | 180 | 250 | 15 | 4 | 215 | 165 | 290 | 385 | ||||||
| 112M | 240 | 175 | 300 | 400 | |||||||||||||||
| 132S | FF265 | 2、4、6、8 | 38 | 80 | 10 | 33 | 265 | 230 | 300 | 260 | 210 | 355 | 470 | ||||||
| 132M | 510 | ||||||||||||||||||
| 160M | FF300 | 42 | 12 | 37 | 300 | 250 | 350 | 0 | 19 | 5 | 315 | 255 | 428 | 615 | |||||
| 160L | 670 | ||||||||||||||||||
| 180M | 48 | 110 | 14 | 42.5 | 350 | 280 | 510 | 700 | |||||||||||
| 180L | 740 | ||||||||||||||||||
| 200L | FF350 | 55 | 16 | 49 | 350 | 300 | 400 | 395 | 305 | 480 | 770 | ||||||||
| 225S | FF400 | 4、8 | 60 | 140 | 18 | 53 | 400 | 350 | 450 | 8 | 450 | 335 | 550 | 815 | |||||
| 225M | 2 | 55 | 110 | 16 | 49 | 820 | |||||||||||||
| 4、6、8 | 60 | 18 | 5358 | 845 | |||||||||||||||
| 250M | FF500 | 2 | 500 | 450 | 550 | 480 | 370 | 595 | 910 | ||||||||||
| 4、6、8 | 65 | ||||||||||||||||||
| 280S | 2 | 530 | 410 | 650 | 985 | ||||||||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 280M | 2 | 65 | 18 | 58 | 1035 | ||||||||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 315S | FF600 | 2 | 65 | 140 | 18 | 58 | 600 | 550 | 660 | 24 | 6 | 8 | 645 | 530 | 845 | 11781208 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
| 315M | FF600 | 2 | 65 | 140 | 18 | 58 | 600 | 550 | 660 | 24 | 6 | 8 | 645 | 530 | 845 | 12881318 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
| 315L | FF600 | 2 | 65 | 140 | 18 | 58 | 600 | 550 | 660 | 24 | 6 | 8 | 645 | 530 | 845 | 12881318 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
机座带底脚，端盖上无凸缘-IMB3
Frame with feet and end-shield without flange-IMB3
| 机座号Frame size | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | AB | AC | AD | HD | L | |||||
| 63M | 2、4 | 100 | 50 | 80 | 40 | 11 | 23 | 4 | 8.5 | 63 | 7 | 135 | 130 | 110 | 173 | 230 | |||
| 71M | 2、4、6 | 112 | 56 | 90 | 45 | 14 | 30 | 5 | 11 | 71 | 150 | 145 | 120 | 191 | 255 | ||||
| 80M | 2、4、6、8 | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 165 | 175 | 130 | 210 | 295 | ||||
| 90S | 140 | 70 | 100125 | 56 | 24 | 50 | 8 | 20 | 90 | 10 | 180 | 195 | 140 | 230 | 320 | ||||
| 90L | 345 | ||||||||||||||||||
| 100L | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100 | 205 | 215 | 165 | 265 | 385 | ||||||
| 112M | 190 | 95 | 140 | 70 | 112 | 230 | 240 | 178 | 290 | 400 | |||||||||
| 132S | 216 | 108 | 140178 | 89 | 38 | 80 | 10 | 33 | 132 | 12 | 270 | 275 | 210 | 345 | 470 | ||||
| 132M | 510 | ||||||||||||||||||
| 160M | 254 | 127 | 210254 | 108 | 42 | 12 | 37 | 160 | 15 | 320 | 330 | 255 | 420 | 615 | |||||
| 160L | 670 | ||||||||||||||||||
| 180M | 279 | 139.5 | 241279 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 700 | |||||
| 180L | 740 | ||||||||||||||||||
| 200L | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 395 | 420 | 305 | 505 | 770 | ||||||
| 225S | 4、8 | 286 | 60 | 140 | 18 | 53 | 225 | 19 | 435 | 470 | 335 | 560 | 815 | ||||||
| 225M | 2 | 356 | 178 | 311 | 149 | 55 | 110 | 16 | 49 | 820 | |||||||||
| 4、6、8 | 60 | 18 | 5358 | 845 | |||||||||||||||
| 250M | 2 | 406 | 203 | 349 | 168 | 60 | 250 | 490 | 510 | 370 | 615 | 910 | |||||||
| 4、6、8 | 65 | ||||||||||||||||||
| 280S | 2 | 368 | 65 | 140 | 280 | 24 | 550 | 580 | 410 | 680 | 985 | ||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 280M | 2 | 457 | 419 | 65 | 18 | 58 | 1035 | ||||||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 315S | 2 | 508 | 254 | 406 | 216 | 65 | 140 | 18 | 58 | 315 | 28 | 635 | 645 | 530 | 845 | 12401270 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
| 315M | 2 | 508 | 254 | 457 | 216 | 65 | 140 | 18 | 58 | 315 | 28 | 635 | 645 | 530 | 845 | 1350 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | 1380 | ||||||||||||||
| 315L | 2 | 508 | 254 | 508 | 216 | 65 | 140 | 18 | 58 | 315 | 28 | 635 | 645 | 530 | 845 | 13501380 | |||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
机座带底脚，端盖上有凸缘(带通孔)-IMB35
Frame with feet and end-shield with flange(with plain holes)-IMB35
| 机座号Frame size | 凸缘号Frangecode | 极数numberofelectrodes | 安装尺寸 Mouting dimension(mm) | 凸缘号孔数number ofpoles on theflange | 外型尺寸Exterior dimension(mm) | |||||||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | M | N | P | R | S | T | AB | AC | AD | HD | L | ||||
| 63M | FF115 | 2、4 | 100 | 50 | 80 | 40 | 11 | 23 | 4 | 8.5 | 63 | 7 | 115 | 95 | 140 | 10 | 3 | 4 | 135 | 130 | 110 | 173 | 230 | |
| 71M | FF130 | 2、4、6 | 112 | 56 | 90 | 45 | 14 | 30 | 5 | 11 | 71 | 130 | 110 | 160 | 150 | 145 | 120 | 191 | 255 | |||||
| 80M | FF165 | 2、4、6、8 | 1256 | 2.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 101 | 651 | 302 | 00 | 12 | 3.5 | 165 | 175 | 130 | 210 | 295 | ||
| 90S | 140 | 70 | 100125 | 56 | 24 | 50 | 8 | 20 | 90 | 180 | 195 | 140 | 230 | 320 | ||||||||||
| 90L | 345 | |||||||||||||||||||||||
| 100L | FF215 | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100112 | 12 | 2151 | 802 | 50 | 15 | 4 | 205 | 215 | 165 | 265 | 385 | ||||
| 112M | 190 | 95 | 140 | 70 | 230 | 240 | 178 | 290 | 400 | |||||||||||||||
| 132S | FF265 | 216 | 108 | 140178 | 89 | 38 | 801 | 03 | 31 | 32 | 2652 | 303 | 00 | 270 | 260 | 210 | 345 | 470 | ||||||
| 132M | 510 | |||||||||||||||||||||||
| 160M | FF300 | 254 | 127 | 210254 | 108 | 42 | 123 | 71 | 60 | 153 | 002 | 503 | 50 | 0 | 19 | 5 | 320 | 315 | 255 | 420 | 615 | |||
| 160L | 670 | |||||||||||||||||||||||
| 180M | 2791 | 39.5 | 241279 | 121 | 48 | 110 | 144 | 2.51 | 80 | 355 | 350 | 280 | 455 | 700 | ||||||||||
| 180L | 740 | |||||||||||||||||||||||
| 200L | FF350 | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 19 | 350 | 3004 | 00 | 395 | 395 | 305 | 505 | 770 | ||||||
| 225S | FF400 | 4、8 | 356 | 178 | 286311 | 149 | 60 | 1401 | 8 | 53 | 2251 | 94 | 003 | 504 | 50 | 8 | 435 | 450 | 335 | 560 | 815 | |||
| 225M | 2 | 55 | 110 | 16 | 49 | 820 | ||||||||||||||||||
| 4、6、8 | 6065 | 140 | 18 | 5358 | 845 | |||||||||||||||||||
| 250M | FF500 | 2 | 4062 | 033 | 491 | 68 | 250280 | 245 | 004 | 505 | 50 | 490 | 480 | 370 | 615 | 910 | ||||||||
| 4、6、8 | ||||||||||||||||||||||||
| 280S | 2 | 368 | 190 | 756575 | 550 | 530 | 410 | 680 | 985 | |||||||||||||||
| 4、6、8 | 206 | 7.5 | ||||||||||||||||||||||
| 280M | 2 | 457 | 419 | 18 | 58 | |||||||||||||||||||
| 1035 | ||||||||||||||||||||||||
| 4、6、8 | 20 | 2067.5 | ||||||||||||||||||||||
| 315S | FF600 | 24、6、8、10 | 508 | 2544 | 062 | 16 | 6580 | 14011702 | 82 | 5871 | 3152 | 86 | 005 | 506 | 60 | 0 | 24 | 6 | 8 | 635 | 645 | 530 | 845 | 12401270 |
| 315M | FF600 | 2 | 5082 | 544 | 572 | 16 | 65 | 1401 | 8 | 58 | 3152 | 86 | 005 | 50 | 660 | 0 | 24 | 6 | 8 | 635 | 645 | 530 | 845 | 13501380 |
| 4、6、8、10 | 80 | 1702 | 2 | 71 | ||||||||||||||||||||
| 315L | FF600 | 24、6、8、10 | 5082 | 544 | 572 | 16 | 6580 1 | 140170 | 822 | 5871 | 315 | 286 | 00 | 550 | 660 | 0 | 24 | 6 | 8 | 635 | 645 | 530 | 845 | 13501380 |
机座不带底脚，端盖上有凸缘(带螺孔)-IMB14
Frame without feet and end-shield with flange(with thread holes)-IMB14
| 机座号Frame size | 凸缘号Frangecode | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 凸缘号孔数 | 外型尺寸Exterior dimension(mm) | |||||||||||||||
| D | E | F | G | M | N | P | R | S | T | number ofpoles on theflange | AC | AD | HF | L | ||||||
| 63M | FT75 | 2、4 | 11 | 23 | 4 | 8.5 | 75 | 60 | 90 | M5 | 2.5 | 4 | 130 | 110 | 175 | 230 | ||||
| 71M | FT85 | 2、4、6 | 14 | 30 | 5 | 11 | 85 | 70 | 105 | M6 | 145 | 120 | 193 | 255 | ||||||
| 80M | FT100 | 2、4、6、8 | 19 | 40 | 6 | 15.5 | 100 | 80 | 120 | |||||||||||
| 175 | 130 | 218 | 295 | |||||||||||||||||
| 90S | FT115 | 24 | 50 | 20 | 115 | 95 | 140 | 0 | M8 | 195 | 140 | 238 | 320345 | |||||||
| 90L | ||||||||||||||||||||
| 100L | FT130 | 28 | 60 | 24 | 130 | 110 | 160 | 3.5 | 215 | 165 | 273 | 385 | ||||||||
| 112M | 240 | 178 | 298 | 400 | ||||||||||||||||
立式安装，机座不带底脚，端盖上有凸缘(带通孔)，轴伸向下-IMV1 Frame without feet and end-shield with flange(with plain holes)-IMV1
机座号(225-315)Frame size
| 机座号Frame size | 凸缘号Frangecode | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number of | 外型尺寸Exterior dimension(mm) | ||||||||||||||
| D | E | F | G | M | N | P | R | S | T | poles on theflange | AC | AD | HF | L | |||||
| 180M | FF300 | 2、4、6、8 | 48 | 110 | 14 | 42.5 | 300 | 250 | 350 | 0 | 19 | 5 | 4 | 380 | 280 | 500 | 760 | ||
| 180L | 800 | ||||||||||||||||||
| 200L | FF350 | 55 | 16 | 49 | 350 | 300 | 400 | 420 | 305 | 550 | 840 | ||||||||
| 225S | 4、8 | 60 | 140 | 18 | 53 | 400 | 350 | 450 | 470 | 335 | 610 | 905 | |||||||
| 225M | FF400 | 2 | 55 | 110 | 16 | 49 | 910 | ||||||||||||
| 4、6、8 | 60 | 18 | 5358 | 935 | |||||||||||||||
| 250M | 2 | 500 | 450 | 550 | 8 | 510 | 370 | 650 | 1015 | ||||||||||
| 4、6、8 | 65 | 140 | |||||||||||||||||
| 280S | |||||||||||||||||||
| 2 | 580 | 410 | 720 | 1110 | |||||||||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 280M | 2 | 65 | 18 | 58 | 1150 | ||||||||||||||
| 4、6、8 | 75 | 20 | 67.5 | ||||||||||||||||
| 315S | FF600 | 2 | 65 | 140 | 18 | 58 | 600 | 550 | 660 | 0 | 24 | 6 | 8 | 645 | 530 | 845 | 13601390 | ||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
| 315M | FF600 | 24、6、8、10 | 6580 | 140170 | 1822 | 5871 | 600 | 550 | 660 | 0 | 24 | 6 | 8 | 645 | 530 | 845 | 14701510 | ||
| 315L | FF600 | 2 | 65 | 140 | 18 | 58 | 600 | 550 | 660 | 0 | 24 | 6 | 8 | 645 | 530 | 845 | 14701510 | ||
| 4、6、8、10 | 80 | 170 | 22 | 71 | |||||||||||||||
2、P尺寸为最大极限值；3、R为凸缘配合面至轴伸肩的距离；4、S孔的位置度公差以轴伸的轴线为基准。
YS系列(IP54)小功率三相异步电动机
产品概述
YS系列(IP54)小功率三相异步电动机在工农业及其它行业的机械配套上占有重要的地位。本系列电动机具有体积小、重量轻、外形美观大方等特点，本系列电动机执行标准为JB/T(009-200)《YS系列三相异步电动机技术条件》。我厂采用铝合金外壳生产的YS50和YS56两个机座号2极、4极共8个规格的电动机。
YS series(IP54) small power three-phase asynchronous motor Brief introduction of the enterprise
YS series (IP54) small power three-phase asynchronous motor has an important position in the industry,agriculture where motor machine is necessary,This series motor have small physical volume, light weight and beautiful appearance.This series motor is made according to JB/T(009-200)《YS series three-phase asynchronous motor's technical conditions. Our factory produces YS50 and YS56 two kinds of frames,motors have 2 & 4 electrodes totally 8 specifications.
YS系列(IP54)三相异步电动机的使用条件
本系列电动机的额定工作制为连续工作制(S,)，额定电压为AC220V/380V，额定频率为50HZ，冷却方法为ICO141(风扇自扇冷却)。
本系列电动机使用环境海拔不超过1000m,环境空气温度不超过40℃、不低于-15℃;最湿月月平均最高相对湿度为90%,同时该月月平均最低温度不高于25℃。
YS series(IP54)three-phase asynchronous motor application conditions:
This series motor's rating work system is continuous work system (S,),rating voltage is AC 200V/380V,rating frequency is 50HZ, cooling method is IC0141(fan cooling).
This series motor's usage environment:elevation can't exceed 1000 meters.Ambient temperature can't exceed 40℃,and not lower than-15C;Average maximum relative humidity should not be over 90%, and the average temperature in a month should not be over 25℃.
技术参数Technical data
| 型号Type | 额定功率Output power | 满载时Full loaded | 空载振动unloadedvibration(mm/s) | 空载噪声unloadedB(A)A) | 堵转电流额定电流LockedrotorcumrentFullload(muple) | 堵转转矩额定转矩LockedrotortorqueFull load(mmple) | 最大转矩额定转矩MaxtorqueFull loadtorque(倍multiple) | ||||
| 瓦(W) | 马力(HP) | 异步转速AandramousSpeed(r/min) | 电流Current(A) | 效率Eff(%) | 功率周数factor(c0s φ) | ||||||
| 同步转速 3000r/min(2极)220/380V 50HzSynchronous Speed 3000r/min(2P)220/380V 50HZ | |||||||||||
| Y,-50M,-2 | 40 | 0.0542 | 6600.2 | 90.17 | 55 | 0.65 | 1.8 | 65 | 6 | 2.3 | 2.3 |
| Y,-50M2-2 | 60 | 0.08 | 26600 | .40/0.23 | 60 | 0.66 | 1.8 | 70 | 6 | 2.3 | 2.3 |
| Y,-56M,-2 | 90 | 0.121 | 26800 | .560.32 | 62 | 0.68 | 1.8 | 70 | 6 | 2.3 | 2.3 |
| Y,-56M2-2 | 120 | 0.16 | 26800 | .660.38 | 67 | 0.71 | 1.8 | 70 | 6 | 2.3 | 2.3 |
| 同步转速 1500r/min(4极)220V/380V50HzSynchronous Speed 1500r/min(4P)220V/380V 50HZ | |||||||||||
| Y,-50M,-4 | 25 | 0.0341 | 3300.2 | 90.17 | 42 | 0.53 | 1.8 | 60 | 6 | 2.4 | 2.4 |
| Y,-50M2-4 | 40 | 0.0541 | 3300.3 | 90.23 | 50 | 0.54 | 1.8 | 60 | 6 | 2.4 | 2.4 |
| Y,-56M,-4 | 60 | 0.08 | 13300. | 480.28 | 56 | 0.58 | 1.8 | 65 | 6 | 2.4 | 2.4 |
| Y,-56M2-4 | 90 | 0.121 | 13300. | 67/0.39 | 58 | 0.61 | 1.8 | 65 | 6 | 2.4 | 2.4 |
机座不带底脚，端盖上有凸缘(带通孔)-IMB5
Frame without feet and end-shield with flange(with plain holes)-IMB5
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 凸线号孔数number ofpoles on thefiange | 外型尺寸Exterior dimension(mm) | |||||||||||
| D | E | F | G | M | N | P | S | T | AC | AD | HF | L | |||
| 56M | 2.4 | 9 | 20 | 3 | 7.2 | 100 | 80 | 120 | 7 | 3 | 4 | 120 | 90 | 145 | 205 |
机座不带底脚，端盖上有凸缘(带螺孔)-IMB14
Frame Without feet and end-shield with flange(with thread holes)-IMB14
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 安装尺寸Mouting dimension(mm) | 外型尺寸Overall dimension(mm) | ||||||||||||
| D | E | F | G | M | N | P | R | S | T | AC | AD | HF | L | |
| YS-50 | 9 | 20 | 3 | 7.2 | 55 | 40 | 70 | 0±1.0 | M5 | 2.5 | 110 | 80 | 115 | 155 |
| YS-56 | 9 | 20 | 3 | 7.2 | 65 | 50 | 80 | 0±1.0 | M5 | 2.5 | 120 | 85 | 140 | 205 |
Note:R is the distance from the flange mounting-surface to the shaft-extension shoulder.
Y2EJ系列(IP54)电磁制动三相异步电动机
产品概况和适用范围：
Y2EJ系列(IP54)电磁制动三相异步电动机是Y2系列(IP54)三相异步电动机的派生系列电动机产品。机座号从63到250共12个机座号，功率从0.12KW到55KW，极数有2、4、6、8极，共72个规格。
Y2EJ系列(IP54)电磁制动三相异步电动机的功率等级、安装尺寸、绝缘等级、工作方式、冷却方式、使用条件等均与Y2系列相应规格相同。执行标准JB/T8680-2008《Y2系列(IP54)三相异步电动机技术条件》和参照JB/T6456-2010《Y2EJ系列(IP44)电磁制动三相异步电动机技术条件》。
电磁制动器额定电压：电动机机座号为71-100者为直流99V，112-250者为直流170V。
Y2EJ系列电动机适用于要求快速停止，准确定位，往复运转，频繁起动，防止滑行的各种机械中作主轴传动和辅助传动用。如升降机械、运输机械、包装机械、印刷机械、食品机械、建筑机械、木工机械、减速机械、冶金机械、锻压机械等。
Y2EJ series(IP54) electromagnetic brake three-phase asynchronous motor Brief introduction and application range:
Y2EJ series(IP54)electromagnetic-brake three-phase asynchronous motor is derived from Y2series (IP54)three-phase asynchronous motor. frame number from 63 to 250,totally 12 frame numbers, the power rangefrom 0.12 to55kw, Electrodes number have 2、4. 6、8total 72 Specifications.this series motor's power grade,installation dimesion,insulating grade,work Mode,cooling mode and applic able condition, etc. are all same asY series.The performingstandards is JB/T8680-2008《The technical conditionsof Y series(IP54)three-phase asynchronous motor》This seires produce according to Q/HDJ01-2008《the technical conditions of YEJseries(IP44)electromagnetism-brake three-phase asynchronous motor》.
Electromagnetism brake rating voltage: only frame size 71-100 are DC 99V,112-250 areDC170V.
YEJ series motor mainly apply to stop quickly, locate to a nicety, reciprocating. frequently start, antisliding,such as lift machinery, transport machingery, colorpacking machinery, pringting machinery, foodstuff machinery, construction machinery, carpenter machinery, reducing machinery, metallurgy machinery, forging machinery etc.
O型号说明：
Mode explain:
例：
Example:
Y2EJ-90S-4 极数 Poles 铁芯长度代号（S为短，M为中，L为长） Iron core length code(the letter'S" is short,"M" is medium,"L" is long) 机座中心高(mm) The central height of the frame(mm) 附加电磁制动器代号 code for auxiliary electromagnetism brake 制动代号 Brake code 异步电动机代号 Code of asynchronous motor
Y2EJ系列(IP54)电磁制动三相异步电动机结构特点与运行原理
YEJ系列(IP54)电磁制动三相异步电动机定转子与Y系列通用，附加的电磁铁由直流励磁。当电动机接通三相电源，电磁铁也同时接通，并产生电磁吸力，将衔铁吸合，使盘式制动器的摩擦面与静止的摩擦副相脱离，电动机在电磁转矩的作用下开始转动，断电后，电磁铁同时断电，电磁铁的电磁吸力消失，衔铁在制动弹簧的压力下，与盘式制动器磨擦面接触，产生摩擦力矩，使电动机停转。电动机在停电制动后，如果需要改变一下转子的位置，可借助于释放装置来实现。转动释放螺钉，可带动两个特殊滑块，使之产生相互位移，将盘式制动器与静止摩擦副相脱开。
Y2EJ series(IP54)electromagnetism brake three-phase asynchronous motor's feature and operation principle
The stator and rotor of Y2 EJ series(IP54)electromagnetism brake three-phase asynchronous motor are general use of Y, series,the attached electromagnetism iron can be excited by direct current. while connect the three phase power source,the electromagnetism iron can get energy and occur the magnetic attraction to attract the armature so as to separate the friction surface of disk. brake from the static frictionsub-phase and then rotate under the actionof magnetictorque,while cut off the electricity the magnetic iron will also out of power and the attraction of magnet will also loss,then,under the pressure of brake spring,the armature willcontact the disk brake and occurthe friction torque and in the final stop the final stop the motor. to change the stator position after the stop of mottor,we can realize the motor stop by releasing device, the proced ure is to rotate release screw. two special sliding blocks and make the mutual displacement so as to separate the disk brake from the static frictoion sub-phase.
1、定子
2、转子
1、stator
3、盘式制动器
2、rotor
3、disk brake
4、衔铁
4、armature
5、励磁线圈
6、释放螺钉
5、excited coil
7、制动弹簧
6、releasescrew
7、brake spring
| 型号Type | 额定功率Output power | 满载时Full loaded | 空载动unloadedvibration(mm/s) | 空载噪声unloadedNoisedB(A) | 堵转电流额定电流Lockedrotorcurrent | 堵转转矩额定转矩Lockedo u | 最大转矩额定转矩Maxtorquie | 制动器静制动力矩Torgue of)brake staticbraking(N.M) | 空载时制动时间unloadedBrakingtime(s) | ||||
| (KW) | (HP) | 异步6Speed(r/min) | 电流Current(A) | 效率Eff(%) | 202功率三(cos φ) | ||||||||
| Fullloadcurrent(倍muitple) | Fullload)(借mulipe | Full load(muipletorque | |||||||||||
| 同步转速 3000r/min(2极)380V 50HzSynchronous Speed 3000r/min(2P)380V 50HZ | |||||||||||||
| Y_2EJ-71M,-2 | 0.37 | 0.5 | 2800 | 0.99 | 70 | 0.81 | 1.8 | 64 | 6.1 | 2.2 | 2.2 | 4.0 | 0.20 |
| Y2EJ-71M2-2 | 0.55 | 0.75 | 2800 | 1.40 | 73 | 0.82 | 1.8 | 64 | 6.1 | 2.2 | 2.3 | 4.0 | 0.20 |
| Y2EJ-80M,-2 | 0.75 | 1 | 2840 | 1.83 | 75 | 0.83 | 1.8 | 67 | 6.1 | 2.2 | 2.3 | 7.5 | 0.20 |
| Y2EJ-80M-2 | 1.1 | 1.5 | 2840 | 2.60 | 76.2 | 0.84 | 1.8 | 71 | 7.0 | 2.2 | 2.3 | 7.5 | 0.20 |
| Y2EJ-90S-2 | 1.5 | 2 | 2840 | 3.50 | 78.5 | 0.84 | 1.8 | 75 | 7.0 | 2.2 | 2.3 | 15 | 0.20 |
| Y2EJ-90L-2 | 2.2 | 3 | 2840 | 4.90 | 81 | 0.85 | 1.8 | 75 | 7.0 | 2.2 | 2.3 | 15 | 0.20 |
| Y2EJ-100L-2 | 3 | 4 | 2860 | 6.30 | 82.6 | 0.87 | 1.8 | 79 | 7.5 | 2.2 | 2.3 | 30 | 0.20 |
| Y,EJ-112M-2 | 4 | 5.5 | 2890 | 8.20 | 84.2 | 0.88 | 1.8 | 79 | 7.5 | 2.2 | 2.3 | 40 | 0.25 |
| Y,EJ-132S-2 | 5.5 | 7.5 | 2900 | 11.1 | 85.7 | 0.88 | 1.8 | 83 | 7.5 | 2.2 | 2.3 | 75 | 0.25 |
| Y,EJ-132S-2 | 7.5 | 10 | 2900 | 14.9 | 87 | 0.88 | 1.8 | 83 | 7.5 | 2.2 | 2.3 | 75 | 0.25 |
| Y2EJ-160M,-2 | 11 | 15 | 2947 | 21.2 | 88.4 | 0.89 | 2.8 | 87 | 7.5 | 2.2 | 2.3 | 150 | 0.35 |
| Y2EJ-160M-2 | 15 | 20 | 2947 | 28.6 | 89.4 | 0.89 | 2.8 | 87 | 7.5 | 2.2 | 2.3 | 150 | 0.35 |
| Y2EJ-160L-2 | 18.5 | 25 | 2947 | 34.7 | 90.5 | 0.90 | 2.8 | 87 | 7.5 | 2.2 | 2.3 | 150 | 0.35 |
| YEJ-180M-2 | 22 | 30 | 2930 | 41 | 90 | 0.90 | 2.8 | 89 | 7.5 | 2.0 | 2.3 | 220 | 0.60 |
| YEJ-200L,-2 | 30 | 40 | 2940 | 55.4 | 91.4 | 0.90 | 2.8 | 92 | 7.5 | 2.0 | 2.3 | 300 | 0.70 |
| YEJ-200L2 | 37 | 50 | 2940 | 67.9 | 92 | 0.90 | 2.8 | 92 | 7.5 | 2.0 | 2.3 | 300 | 0.70 |
| YEJ-225M-2 | 45 | 60 | 2970 | 82.1 | 92.5 | 0.90 | 3.5 | 92 | 7.5 | 2.0 | 2.3 | 450 | 0.8 |
| YEJ-250M-2 | 55 | 74 | 2970 | 99.8 | 93 | 0.90 | 3.5 | 102 | 7.5 | 2.0 | 2.3 | 600 | 0.8 |
| Y2EJ-280S-2 | 75 | 100 | 2970 | 135.3 | 93.6 | 0.90 | 3.5 | 103 | 7.5 | 2.0 | 2.3 | 850 | 1.2 |
| YEJ-280M-2 | 90 | 121 | 2970 | 160 | 93.9 | 0.91 | 3.5 | 106 | 7.5 | 2.0 | 2.3 | 850 | 1.2 |
| 同步转速 1500r/min(4极)380V50HzSynchronous Speed 1500r/min(2P)380V 50HZ | |||||||||||||
| Y2EJ-71M,-4 | 0.25 | 0.34 | 1350 | 0.79 | 65 | 0.74 | 1.8 | 58 | 5.2 | 2.1 | 2.2 | 4.0 | 0.20 |
| Y_EJ-71M2-4 | 0.37 | 0.5 | 1350 | 1.12 | 67 | 0.75 | 1.8 | 58 | 5.2 | 2.1 | 2.2 | 4.0 | 0.20 |
| Y2EJ-80M,-4 | 0.55 | 0.75 | 1380 | 1.57 | 71 | 0.75 | 1.8 | 61 | 5.2 | 2.4 | 2.3 | 7.5 | 0.20 |
| Y2EJ-80M24 | 0.75 | 1 | 1380 | 2.05 | 73 | 0.76 | 1.8 | 61 | 6.0 | 2.3 | 2.3 | 7.5 | 0.20 |
| YEJ-90S 4 | 1.1 | 1.5 | 1390 | 2.8 | 76.2 | 0.77 | 1.8 | 67 | 6.0 | 2.3 | 2.3 | 15 | 0.20 |
| Y2EJ-90L-4 | 1.5 | 2 | 1390 | 3.7 | 78.5 | 0.79 | 1.8 | 67 | 6.0 | 2.3 | 2.3 | 15 | 0.20 |
| YEJ-100L,-4 | 2.2 | 3 | 1410 | 5.1 | 81 | 0.81 | 1.8 | 70 | 7.0 | 2.3 | 2.3 | 30 | 0.20 |
| YEJ-100L-4 | 3 | 4 | 1410 | 6.7 | 82.6 | 0.82 | 1.8 | 70 | 7.0 | 2.3 | 2.3 | 30 | 0.20 |
| Y,EJ-112M-4 | 4 | 5.5 | 1440 | 8.8 | 84.2 | 0.82 | 1.8 | 74 | 7.0 | 2.3 | 2.3 | 40 | 0.25 |
| Y2EJ-132S-4 | 5.5 | 7.5 | 1450 | 11.7 | 85.7 | 0.83 | 1.8 | 78 | 7.0 | 2.3 | 2.3 | 75 | 0.25 |
| YEJ-132M-4 | 7.5 | 10 | 1450 | 15.6 | 87 | 0.84 | 1.8 | 78 | 7.0 | 2.3 | 2.3 | 75 | 0.25 |
| YEJ-160M-4 | 11 | 15 | 1460 | 22.5 | 88.4 | 0.84 | 2.8 | 82 | 7.0 | 2.2 | 2.3 | 150 | 0.35 |
| Y,EJ-160L-4 | 15 | 20 | 1460 | 30.0 | 89.4 | 0.85 | 2.8 | 82 | 7.0 | 2.2 | 2.3 | 150 | 0.35 |
| YEJ-180M-4 | 18.5 | 25 | 1470 | 36.3 | 90 | 0.86 | 2.8 | 82 | 7.5 | 2.2 | 2.3 | 220 | 0.60 |
| Y,EJ-180L-4 | 22 | 30 | 1470 | 42.9 | 90.5 | 0.86 | 2.8 | 82 | 7.5 | 2.2 | 2.3 | 300 | 0.70 |
| YEJ-200L-4 | 30 | 40 | 1470 | 58 | 91.4 | 0.86 | 2.8 | 84 | 7.2 | 2.2 | 2.3 | 300 | 0.70 |
| YEJ-225S-4 | 37 | 50 | 1480 | 70.2 | 92 | 0.87 | 3.5 | 81 | 7.2 | 2.2 | 2.3 | 450 | 0.80 |
| Y2EJ-225M-4 | 45 | 60 | 1480 | 85 | 92.5 | 0.87 | 3.5 | 81 | 7.2 | 2.2 | 2.3 | 450 | 0.80 |
| Y2EJ-250M-4 | 55 | 74 | 1480 | 103.3 | 93 | 0.87 | 3.5 | 92 | 7.2 | 2.2 | 2.3 | 600 | 0.8 |
| YEJ-280S-4 | 75 | 100 | 1480 | 139.9 | 93.6 | 0.87 | 3.5 | 95 | 7.2 | 2.2 | 2.3 | 850 | 1.2 |
| YEJ-280M-4 | 90 | 120 | 1480 | 167.4 | 93.9 | 0.87 | 3.5 | 95 | 7.2 | 2.2 | 2.3 | 850 | 1.2 |
技术参数Technical data
| 型号Type | 额定功率Output power | 满载时Full loaded | 越振动 | 空载噪声 | 堵转电流额定电流Lockedrotorcument | 堵转转矩额定转矩Lockedto | 最大转矩额定转矩Maxtorque | 制动器静制动力矩Torgue ofbrake staticbraking(N.M) | 空载时制动时间unloadedBrakingtime(s) | ||||
| (KW) | (HP) | 异选速AscionusSpeed(r/min) | 电流Current(A) | 效率Eff(%) | 功率rfactor(cOs φ) | vibration(mm/s) | |||||||
| NoisedB(A) | Full load(倍muliplecurrent | Full loady(倍muple)torque, | Full load(倍mumple)torque | ||||||||||
| 同步转速 1000r/min(6极)380V50HzSynchronous Speed 1000r/min(6P)380V 50HZ | |||||||||||||
| Y,EJ-71M,-6 | 0.18 | 0.25 | 850 | 0.74 | 56 | 0.66 | 1.8 | 56 | 4.0 | 2.0 | 2.0 | 4.0 | 0.20 |
| Y2EJ-71M_2-6 | 0.25 | 0.34 | 850 | 0.95 | 59 | 0.68 | 1.8 | 56 | 4.0 | 2.0 | 2.0 | 4.0 | 0.20 |
| Y2EJ-80M,-6 | 0.37 | 0.5 | 885 | 1.30 | 62 | 0.70 | 1.8 | 56 | 4.7 | 2.0 | 2.0 | 7.5 | 0.20 |
| YEJ-80M2-6 | 0.55 | 0.75 | 885 | 1.79 | 65 | 0.72 | 1.8 | 58 | 4.7 | 2.0 | 2.1 | 7.5 | 0.20 |
| Y2EJ-90S-6 | 0.75 | 1 | 910 | 2.29 | 69 | 0.72 | 1.8 | 61 | 5.6 | 2.1 | 2.1 | 15 | 0.20 |
| Y2EJ-90L-6 | 1.1 | 1.5 | 910 | 3.2 | 72 | 0.73 | 1.8 | 65 | 6.4 | 2.1 | 2.1 | 15 | 0.20 |
| YEJ-100L-6 | 1.5 | 2 | 920 | 4.0 | 76 | 0.75 | 1.8 | 67 | 6.4 | 2.1 | 2.1 | 30 | 0.20 |
| Y,EJ-112M-6 | 2.2 | 3 | 940 | 5.60 | 79 | 0.76 | 1.8 | 67 | 6.4 | 2.1 | 2.1 | 40 | 0.25 |
| YEJ-132S-6 | 3 | 4 | 960 | 7.40 | 81 | 0.76 | 1.8 | 71 | 6.4 | 2.1 | 2.1 | 75 | 0.25 |
| YEJ-132M,-6 | 4 | 5.5 | 960 | 9.8 | 82 | 0.76 | 1.8 | 71 | 7.0 | 2.1 | 2.1 | 75 | 0.25 |
| Y2EJ-132M2-6 | 5.5 | 7.5 | 960 | 12.9 | 84 | 0.77 | 1.8 | 71 | 7.0 | 2.1 | 2.1 | 75 | 0.35 |
| Y2EJ-160M-6 | 7.5 | 10 | 960 | 17.2 | 86 | 0.77 | 2.8 | 75 | 7.0 | 1.9 | 2.1 | 150 | 0.35 |
| Y2EJ-160L-6 | 11 | 15 | 960 | 24.5 | 87.5 | 0.78 | 2.8 | 75 | 7.0 | 2.1 | 2.1 | 150 | 0.35 |
| Y2EJ-180L-6 | 15 | 20 | 970 | 31.6 | 89 | 0.81 | 2.8 | 78 | 6.5 | 2.0 | 2.1 | 220 | 0.60 |
| Y2EJ-200L,-6 | 18.5 | 25 | 970 | 38.6 | 90 | 0.81 | 2.8 | 78 | 6.5 | 2.1 | 2.1 | 300 | 0.70 |
| Y2EJ-200L-6 | 22 | 30 | 970 | 44.7 | 90 | 0.83 | 2.8 | 78 | 6.5 | 2.0 | 2.1 | 300 | 0.70 |
| Y2EJ-225M-6 | 30 | 40 | 980 | 59.3 | 91.5 | 0.84 | 3.5 | 76 | 7 | 1.8 | 2.1 | 450 | 0.80 |
| YEJ-250M-6 | 37 | 49.6 | 980 | 71.1 | 92.0 | 0.86 | 3.5 | 78 | 7 | 2.1 | 2.1 | 600 | 0.80 |
| Y,EJ-280S-6 | 45 | 60 | 980 | 85.9 | 92.5 | 0.86 | 3.5 | 80 | 7 | 2.1 | 2.0 | 850 | 1.2 |
| Y2EJ-280M-6 | 55 | 74 | 980 | 104.7 | 92.8 | 0.86 | 3.5 | 80 | 7 | 2.1 | 2.0 | 850 | 1.2 |
| 同步转速 750r/min(8极)380V 50HzSynchronous Speed 750r/min(8P)380V 50Hz | |||||||||||||
| Y,EJ-80M,-8 | 0.18 | 0.24 | 645 | 0.88 | 51 | 0.61 | 1.8 | 51 | 3.3 | 1.8 | 1.9 | 7.5 | 0.20 |
| Y2EJ-80M2-8 | 0.25 | 0.34 | 645 | 1.15 | 54 | 0.61 | 1.8 | 51 | 3.3 | 1.8 | 1.9 | 7.5 | 0.20 |
| YEJ-90S-8 | 0.37 | 0.5 | 670 | 1.49 | 62 | 0.61 | 1.8 | 56 | 4.0 | 1.8 | 2.0 | 15 | 0.20 |
| Y,EJ-90L-8 | 0.55 | 0.75 | 670 | 2.17 | 63 | 0.61 | 1.8 | 56 | 4.0 | 1.8 | 2.0 | 15 | 0.20 |
| Y2EJ-100L,-8 | 0.75 | 1.0 | 680 | 2.4 | 71 | 0.67 | 1.8 | 61 | 4.0 | 1.8 | 2.0 | 30 | 0.20 |
| Y,EJ-100L-8 | 1.1 | 1.5 | 680 | 3.3 | 73 | 0.69 | 1.8 | 61 | 5.0 | 1.8 | 2.0 | 30 | 0.20 |
| Y2EJ-112M-8 | 1.5 | 2 | 690 | 4.4 | 75 | 0.69 | 1.8 | 65 | 5.0 | 1.8 | 2.0 | 40 | 0.25 |
| YEJ-132S-8 | 2.2 | 3 | 710 | 6.0 | 78 | 0.71 | 1.8 | 66 | 5.0 | 1.8 | 2.0 | 75 | 0.25 |
| YEJ-132M-8 | 3 | 4 | 710 | 7.9 | 79 | 0.73 | 1.8 | 66 | 6.0 | 1.9 | 2.0 | 75 | 0.25 |
| YEJ-160M,-8 | 4 | 5.5 | 720 | 10.3 | 81 | 0.73 | 2.8 | 69 | 6.0 | 1.9 | 2.0 | 150 | 0.35 |
| Y2EJ-160M2-8 | 5.5 | 7.5 | 720 | 13.6 | 83 | 0.74 | 2.8 | 69 | 6.0 | 2.0 | 2.0 | 150 | 0.35 |
| YEJ-160L-8 | 7.5 | 10 | 720 | 17.8 | 85.5 | 0.75 | 2.8 | 72 | 6.0 | 2.0 | 2.0 | 150 | 0.35 |
| YEJ-180L-8 | 11 | 15 | 730 | 25.1 | 87.5 | 0.76 | 2.8 | 75 | 6.6 | 2.0 | 2.0 | 220 | 0.60 |
| Y,EJ-200L-8 | 15 | 20 | 730 | 34.1 | 88.0 | 0.76 | 2.8 | 75 | 6.6 | 2.0 | 2.0 | 300 | 0.70 |
| Y2EJ-225S-8 | 18.5 | 25 | 730 | 41.1 | 90 | 0.76 | 3.5 | 73 | 6.6 | 1.9 | 2.0 | 450 | 0.80 |
| YEJ-225M-8 | 22 | 30 | 740 | 47.4 | 90.5 | 0.78 | 3.5 | 73 | 6.6 | 1.9 | 2.0 | 450 | 0.80 |
| YEJ-250M-8 | 30 | 40 | 740 | 63.4 | 91 | 0.79 | 3.5 | 84 | 6.6 | 1.9 | 2.0 | 600 | 0.80 |
| Y,EJ-280S-8 | 37 | 50 | 740 | 77.8 | 91.5 | 0.79 | 3.5 | 84 | 6.6 | 1.9 | 2.0 | 850 | 1.2 |
| Y2EJ-280M-8 | 45 | 60 | 740 | 94.1 | 92.0 | 0.79 | 3.5 | 84 | 6.6 | 1.9 | 2.0 | 850 | 1.2 |
机座不带底脚，端盖上有凸缘(带通孔)-IMB5 Frame without feet and end-shield with flange(with plain holes)-IMB5
| 机座号Frame size | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||
| D | E | F | G | M | N | P | R | S | T | AC | AD | HF | L | |
| 71M | 14 | 30 | 5 | 11 | 130 | 110 | 160 | 0±1.5 | 10 | 3.5 | 145 | 120 | 200 | 306 |
| 80M | 19 | 40 | 6 | 15.5 | 165 | 130 | 200 | 0±1.5 | 12 | 3.5 | 175 | 130 | 230 | 307 |
| 90S | 24 | 50 | 8 | 20 | 195 | 140 | 240 | 394 | ||||||
| 90L | 425 | |||||||||||||
| 100L | 28 | 60 | 24 | 215 | 180 | 250 | 0±2.0 | 15 | 4.0 | 215 | 165 | 290 | 482 | |
| 112M | 4.0 | 240 | 175 | 300 | 500 | |||||||||
| 132S | 38 | 80 | 10 | 33 | 265 | 230 | 300 | 0±2.0 | 15 | 4.0 | 275 | 210 | 315 | 588 |
| 132M | 638 | |||||||||||||
| 160M | 42 | 12 | 37 | 300 | 250 | 350 | 0±3.0 | 19 | 5.0 | 330 | 255 | 385 | 769 | |
| 160L | 838 | |||||||||||||
| 180M | 48 | 110 | 14 | 42.5 | 380 | 280 | 430 | 820 | ||||||
| 180L | 870 | |||||||||||||
| 200L | 55 | 16 | 49 | 350 | 300 | 400 | 0±3.0 | 19 | 5.0 | 420 | 305 | 480 | 898 | |
| 225S | 60 | 140 | 18 | 53 | 400 | 350 | 450 | 0±4.0 | 19 | 5.0 | 475 | 345 | 535 | 1000 |
| 225M | 1030 | |||||||||||||
| 250M | 65 | 140 | 18 | 58 | 500 | 450 | 550 | 0±4.0 | 19 | 5.0 | 500 | 370 | 595 | 1060 |
| 280S | 75 | 140 | 20 | 67.5 | 500 | 450 | 550 | 0±4.0 | 19 | 5.0 | 540 | 410 | 650 | 1100 |
| 280M | 75 | 140 | 20 | 67.5 | 500 | 450 | 550 | 0±4.0 | 19 | 5.0 | 540 | 410 | 650 | 1151 |
机座带底脚，端盖上无凸缘-IMB3 Frame with feet and end-shield without flange-IMB3
机座号(71-280)Frame size
| 机座号Frame size | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | |||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | AB | AC | AD | HD | L | |
| 71M | 112 | 56 | 90 | 45 | 14 | 30 | 5 | 11 | 71 | 7 | 150 | 145 | 120 | 191 | 306 |
| 80M | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 10 | 165 | 175 | 130 | 210 | 370 |
| 90S | 140 | 70 | 100 | 56 | 24 | 50 | 8 | 20 | 90 | 180 | 195 | 140 | 230 | 394 | |
| 90L | 125 | 425 | |||||||||||||
| 100L | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100 | 205 | 215 | 165 | 265 | 482 | ||
| 112M | 190 | 95 | 140 | 70 | 112 | 230 | 240 | 178 | 290 | 500 | |||||
| 132S | 216 | 108 | 140 | 89 | 38 | 80 | 10 | 33 | 132 | 270 | 275 | 210 | 345 | 588 | |
| 132M | 178 | 638 | |||||||||||||
| 160M | 254 | 127 | 210 | 108 | 42 | 12 | 37 | 160 | 320 | 330 | 255 | 420 | 769 | ||
| 160L | 254 | 838 | |||||||||||||
| 180M | 279 | 139.5 | 241 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 820 | |
| 180L | 279 | 870 | |||||||||||||
| 200L | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 19 | 395 | 420 | 305 | 505 | 898 | |
| 225S | 356 | 178 | 286 | 149 | 60 | 140 | 18 | 53 | 225 | 19 | 435 | 475 | 345 | 530 | 10001030 |
| 225M | 311 | ||||||||||||||
| 250M | 406 | 203 | 349 | 168 | 65 | 140 | 18 | 58 | 250 | 24 | 490 | 500 | 370 | 615 | 1060 |
| 280S | 457 | 228.5 | 368 | 190 | 75 | 140 | 20 | 67.5 | 280 | 24 | 550 | 540 | 410 | 680 | 1134 |
| 280M | 457 | 228.5 | 419 | 190 | 75 | 140 | 20 | 67.5 | 280 | 24 | 550 | 540 | 410 | 680 | 1185 |
机座带底脚，端盖上有凸缘(带通孔)-IMB35
Frame with feet and end-shield with flange(with plain holes)-IMB35
机座号(71-200)Frame size
机座号(225-280)Frame size
| 机座号Frame size | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | |||||||||||||||||||
| A | AV/2 | B | C | D | E | F | G | H | K | M | N | P | R | S | T | AB | AC | AD | HD | L | |
| 71M | 112 | 56 | 90 | 45 | 14 | 30 | 5 | 11 | 71 | 7 | 130 | 110 | 160 | 0±1.5 | 10 | 3.5 | 150 | 145 | 120 | 191 | 306 |
| 80M | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 10 | 165 | 130 | 200 | 0±1.51 | 2 | 165 | 175 | 130 | 210 | 370 | |
| 90S | 140 | 70 | 100 | 56 | 24 | 50 | 8 | 20 | 90 | 3.5 | 180 | 195 | 140 | 230 | 394 | ||||||
| 90L | 125 | 425 | |||||||||||||||||||
| 100L | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100 | 215 | 180 | 250 | 0±2 | 15 | 4 | 205 | 215 | 165 | 265 | 482 | ||
| 112M | 190 | 95 | 140 | 70 | 112 | 4 | 230 | 240 | 178 | 290 | 500 | ||||||||||
| 132S | 216 | 108 | 140178 | 89 | 38 | 80 | 10 | 33 | 132 | 265 | 230 | 300 | 0±2 | 15 | 4 | 270 | 275 | 210 | 345 | 588 | |
| 132M | 638 | ||||||||||||||||||||
| 160M | 254 | 127 | 210 | 108 | 42 | 12 | 37 | 160 | 15 | 300 | 250 | 350 | 0±3 | 19 | 5 | 320 | 330 | 255 | 420 | 769 | |
| 160L | 254 | 838 | |||||||||||||||||||
| 180M | 279 | 139.5 | 241279 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 820 | |||||||
| 180L | 870 | ||||||||||||||||||||
| 200L | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 19 | 350 | 300 | 400 | 0±3 | 19 | 5 | 395 | 420 | 305 | 505 | 898 | |
| 225S | 356 | 178 | 286 | 149 | 60 | 140 | 18 | 53 | 225 | 19 | 400 | 350 | 450 | 0±4.01 | 9 | 5 | 430 | 475 | 345 | 530 | 1000 |
| 225M | 311 | 1030 | |||||||||||||||||||
| 250M | 406 | 203 | 349 | 168 | 65 | 140 | 18 | 58 | 250 | 24 | 500 | 450 | 550 | 0±4.0 | 19 | 5 | 490 | 500 | 370 | 615 | 1060 |
| 280S | 457 | 228.5 | 368 | 190 | 75 | 140 | 20 | 67.5 | 280 | 24 | 500 | 450 | 550 | 0±4.0 | 19 | 5 | 550 | 540 | 410 | 680 | 1134 |
| 280M | 457 | 228.5 | 419 | 190 | 75 | 140 | 20 | 67.5 | 280 | 24 | 500 | 450 | 550 | 0±4.0 | 19 | 5 | 550 | 540 | 410 | 680 | 1185 |
YVF2系列（IP54)变频调速三相异步电动机
YVF系列变频调速三相异步电动机是在全国最新统一设计的Y,系列(IP54)电动机基础上派生的系列电动机，外形结构新颖美观，噪声低，振动小。它具有较宽的调速范围，并且调速平稳无级；具有独立通风散热系统可低速长期运行。与各类变频器具有良好的参数匹配，配合矢量控制具有快速动态响应；低速无转矩脉动，无共振现象；YVF系列(IP54)三相异步电动机从80\~315共12个机座号，计23个规格，目前我厂研制生产从80\~280共11个机座号19个规格的电动机。按JB/T7118-2004《YVF2系列(IP54)变频调速三相异步电动机技术条件》有关规定设计制造。按客户需要还可以提供YVFEJ系列变频调速电磁制动三相异步电动机。
YVF2系列（IP54）变频调速三相异步电动机的工作条件：
(1)、海拔高度不超过1000M
(2)、环境空气温度不超过40℃，不低于-15℃。
(3)、月平均最高湿度不超过90%，同时该月月平均最低温度不高于25℃。
(4)、工作制为连续工作制（S.）。
(5)、采用F级绝缘。
(6)、额定电压为380V。
(7)、额定基频为50Hz，一般为4极。
(8)、通风冷却为IC416（独立风机冷却）。
YVF2 series(IP54) frequency varied three-phase asynchronous motor
YVF series (IP54)frequency-varied and speed-adjustable three phase asynchronous motor is the latest unify design in our country,which derived from Yseries (lP54).They not onlylooks beautiful and dignified,but also low noise, low vibration.They have wide scope regulate speed and it is so steady that has no class. They have independent and well ventilated cooling system,and they can run at low speed over a long time.The motors are matched with all transducer,have the fast dynamic responding with vector control,no torque wave at low speed,no resonance,For this series the frame number is from 80 to 315,totally 12 frame numbers and 23 specifications.At present,our factory produces motor at the frame number from 80 to 280,totally 11 frame numbers and 19 specifications,This series is made according to theJB/T7118-2004《The technical conditions for YVF series (IP54) frequency-varied and multi- speed three phase asynchronous motor,We can also produce YVFEJ series frequency-varied speed-varied electromagnetism brake three-phase asynchronous motor.
YVF2 Series(IP54)three-phase asynchronous motor's application canditions: (1).Elevation shouldn't surpass 1000 metres.
(2).The ambient temperature shouldn't surpass 40C,and not lower than-15℃.
(3)Average maximum relative humidity should not be over 90% for every month.The average temperature in a month should not be over 25℃.
(4).Work system is S1(continuing work system).
(5).Insulation degree is F grade.
(6).Rating voltage is 380V.
(7).Rating frequency is 50Hz.
(8).Cooling mode is IC416(cooling by independent fan).
变频电动机在变频器供电条件下空载时振动速度有效值和噪声值应≤以下表中值：
Vibration and noise while unloaded and power supplied by frequency-Varied machine should≤next list:
| 机座号 Frame Size | 80 | 90 | 100 | 112 | 132 | 160 | 180 | 200 | 225 | 250 | 280 |
| 振动 Vibration(mm/s) | 1.8 | 1.8 | 1.8 | 1.8 | 1.8 | 2.8 | 2.8 | 2.8 | 2.8 | 3.5 | 3.5 |
| 噪声 Niose dB(A) | 73 | 76 | 79 | 80 | 86 | 90 | 91 | 92 | 94 | 96 | 99 |
变频电动机在额定电压和额定频率(基频)下的堵转转矩、最大转矩、起动过程中最小转矩以额定转矩之比应》以下表中值：
Frequency-varied regulator-speed notor under the rated and rated frequency, locked rotor torque Max.Torque.Mini.Torque at starting while idle,their specific value to the full load torque≥the value next list:
技术参数Technical data
| 功率 Output(kw) | 0.55 | 0.75-1.5 | 2.2~4 | 5.5~15 | 18.5~37 | 45~55 | 75~160 |
| 堵转转矩 Locked rotor torque额定转矩 Full load torque(倍multiple) | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 1.7 | 1.7 |
| 最大转矩 Max.torque额定转矩 Full load torque(倍multiple) | 2.8 | 2.8 | 2.8 | 2.8 | 2.8 | 2.8 | 2.8 |
| 最小转矩 Min.torque额定转矩 Fullloadtorque(倍multiple) | 1.7 | 1.6 | 1.5 | 1.4 | 1.2 | 1.1 | 1.0 |
变频电动机的机座，标称功率、额定转矩及变频范围如下表：
Frequency-varied motor frame,ratedoutput power,full load torque and frequency-varied limits as follows list:
| 机座号Frame Size | 标称电流Output Current(A) | 标称功率Output Power(kw) | 额定转矩Full load torque(N.m) | 恒转矩变频范围Constont torquefrequency-varied limits(Hz) | 恒功率变频范围Constont powerfrequency-varied limits(Hz) |
| YVF280M.-4 | 1.57 | 0.55 | 3.5 | 5~50 | 50~100 |
| YVF,80M2-4 | 2.05 | 0.75 | 4.7 | ||
| YVF,90S-4 | 2.89 | 1.1 | 7.0 | ||
| YVF,90L-4 | 3.7 | 1.5 | 9.5 | ||
| YVF,100L,-4 | 5.16 | 2.2 | 14 | ||
| YVF,100L,-4 | 6.8 | 3 | 19 | ||
| YVF2112M-4 | 9.3 | 4 | 25.4 | ||
| YVF,132S-4 | 11.8 | 5.5 | 35 | ||
| YVF2132M-4 | 15.6 | 7.5 | 47.7 | ||
| YVF.160M-4 | 22.3 | 11 | 70 | ||
| YVF,160L-4 | 30.1 | 15 | 95.5 | ||
| YVF2180M-4 | 36.5 | 18.5 | 117.1 | ||
| YVF2180L-4 | 43.5 | 22 | 140.9 | ||
| YVF,200L-4 | 57.6 | 30 | 190.9 | ||
| YVF:225S-4 | 69.9 | 37 | 235.5 | ||
| YVF.225M-4 | 84.7 | 45 | 286.4 | ||
| YVF2250M-4 | 103.3 | 55 | 350.1 | 3~50 | |
| YVF.280S-4 | 139.6 | 75 | 447.7 | ||
| YVF2280M-4 | 166.9 | 90 | 572.9 |
机座号(80-200) Frame size
变频电动机配套的变频器容量和配套轴流风机容量：
Frequency-varied motor matched frequency varied device and bearing fan capacity:
技术参数Technical data
| 机座号Frame size | 功率Output power(kw) | 变频器容量Capacity ofthe frequency-varied device(KVA) | 风机额定电压Rated voltageof the fan(V) | 风机额定频率Rated voltageof the fan(Hz) | 风机容量Fan capactiy(W) | 风机转速Fan speed(r/min) |
| YVF280M,-4 | 0.55 | 1 | 380 | 50 | 30 | 2800 |
| YVF280M,-4 | 0.75 | 1 | 380 | 50 | 30 | 2800 |
| YVF290S-4 | 1.1 | 2 | 380 | 50 | 42 | 2800 |
| YVF290L-4 | 1.5 | 3 | 380 | 50 | 42 | 2800 |
| YVF2100L,-4 | 2.2 | 4 | 380 | 50 | 52 | 2800 |
| YVF2100L-4 | 3 | 6 | 380 | 50 | 52 | 2800 |
| YVF2112M-4 | 4 | 10 | 380 | 50 | 60 | 2800 |
| YVF2132S-4 | 5.5 | 10 | 380 | 50 | 80 | 2800 |
| YVF2132M-4 | 7.5 | 10 | 380 | 50 | 80 | 1400 |
| YVF2160M-4 | 11 | 15 | 380 | 50 | 80 | 1400 |
| YVF2160L-4 | 15 | 20 | 380 | 50 | 80 | 1400 |
| YVF2180M-4 | 18.5 | 30 | 380 | 50 | 80 | 1400 |
| YVF2180L-4 | 22 | 30 | 380 | 50 | 80 | 1400 |
| YVF,200L-4 | 30 | 40 | 380 | 50 | 150 | 1400 |
| YVF225S-4 | 37 | 50 | 380 | 50 | 200 | 1400 |
| YVF2225M-4 | 45 | 60 | 380 | 50 | 200 | 1400 |
| YVF2250M-4 | 55 | 70 | 380 | 50 | 200 | 1400 |
| YVF,280S-4 | 75 | 100 | 380 | 50 | 300 | 1400 |
| YVF2280M-4 | 90 | 120 | 380 | 50 | 300 | 1400 |
机座不带底脚，端盖上有凸缘(带通孔)-IMB5 Frame without feet end-shield with flange(with plain holes)-IMB5
| 机座号Frame size | 凸缘号 | 安装尺寸Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||||
| code | D | E | F | G | M | N | P | R | s | T | AC | AD | HF | L | L(Y,ZJVF) | ||
| 80M | FF165 | 19 | 40 | 6 | 15.5 | 165 | 130 | 200 | 0±1.5 | 12 | 3.5 | 175 | 130 | 230 | 370 | 423 | |
| 90S | FF165 | 24 | 50 | 8 | 20 | 165 | 130 | 200 | 0±1.5 | 12 | 3.5 | 195 | 140 | 240 | 380 | 450 | |
| 90L | FF165 | 24 | 50 | 8 | 20 | 165 | 130 | 200 | 0±1.5 | 12 | 3.5 | 195 | 140 | 240 | 410 | 475 | |
| 100L | FF215 | 28 | 60 | 8 | 24 | 215 | 180 | 250 | 0±2.0 | 15 | 4 | 215 | 165 | 290 | 465 | 520 | |
| 112M | FF215 | 28 | 60 | 8 | 24 | 215 | 180 | 250 | 0 ±2.0 | 15 | 4 | 240 | 175 | 300 | 480 | 550 | |
| 132S | FF265 | 38 | 80 | 10 | 33 | 265 | 230 | 300 | 0±2.0 | 15 | 4 | 275 | 210 | 315 | 530 | 620 | |
| 132M | FF265 | 38 | 80 | 10 | 33 | 265 | 230 | 300 | 0±2.0 | 15 | 4 | 275 | 210 | 315 | 570 | 652 | |
| 160M | FF300 | 42 | 110 | 12 | 37 | 300 | 250 | 350 | 0±3.0 | 19 | 5 | 330 | 255 | 385 | 660 | 765 | |
| 160L | FF300 | 42 | 110 | 12 | 37 | 300 | 250 | 350 | 0±3.0 | 19 | 5 | 330 | 255 | 385 | 715 | 810 | |
| 180M | FF300 | 48 | 110 | 14 | 42.5 | 300 | 250 | 350 | 0±3.0 | 19 | 5 | 380 | 280 | 430 | 775 | 867 | |
| 180L | FF300 | 48 | 110 | 14 | 42.5 | 300 | 250 | 350 | 0±3.0 | 19 | 5 | 380 | 280 | 430 | 815 | 905 | |
| 200L | FF350 | 55 | 110 | 16 | 49 | 350 | 300 | 400 | 0±3.0 | 19 | 5 | 420 | 305 | 480 | 850 | 1005 | |
| 225S | FF400 | 60 | 18 | 53 | 400 | 350 | 450 | 470 | 335 | 535 | 885 | 1035 | |||||
| 225M | 915 | 1060 | |||||||||||||||
| 250M | FF500 | 65 | 140 | 20 | 58 | 500 | 450 | 550 | 0 | 19 | 510 | 370 | 595 | 980 | |||
| 280S | 75 | 67.5 | 580 | 410 | 650 | 1085 | |||||||||||
| 280M | 1135 | ||||||||||||||||
机座带底脚，端盖上无凸缘-IMB3
Frame with feet and end-shield without flange-IMB3
| 机座号Frame size | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | AB | AC | AD | HD | L | L(Y,ZJVF) | |||
| 80M | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 165 | 175 | 130 | 210 | 370 | 423 | |||
| 90S | 140 | 70 | 100 | 56 | 24 | 50 | 8 | 20 | 90 | 10 | 180 | 195 | 140 | 230 | 380 | 450 | ||
| 90L | 125 | 410 | 475 | |||||||||||||||
| 100L | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100 | 205 | 215 | 165 | 265 | 465 | 520 | ||||
| 112M | 190 | 95 | 140 | 70 | 112 | 230 | 240 | 178 | 290 | 480 | 550 | |||||||
| 12 | ||||||||||||||||||
| 132S | 216 | 108 | 140 | 89 | 38 | 80 | 10 | 33 | 132 | 270 | 275 | 210 | 345 | 530 | 620 | |||
| 132M | 178 | 570 | 652 | |||||||||||||||
| 160M | 254 | 127 | 210 | 108 | 42 | 12 | 37 | 160 | 15 | 320 | 330 | 255 | 420 | 660 | 765 | |||
| 160L | 254 | 715 | 810 | |||||||||||||||
| 180M | 279 | 139.5 | 241 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 775 | 867 | |||
| 180L | 279 | 815 | 905 | |||||||||||||||
| 200L | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 395 | 420 | 305 | 505 | 850 | 1005 | ||||
| 225S | 356 | 178 | 286 | 149 | 60 | 140 | 18 | 53 | 225 | 19 | 435 | 470 | 335 | 560 | 885 | 1035 | ||
| 225M | 311 | 915 | 1060 | |||||||||||||||
| 250M | 406 | 203 | 349 | 168 | 65 | 58 | 250 | 490 | 510 | 370 | 615 | 980 | ||||||
| 280S | 457 | 228.5 | 368 | 190 | 75 | 20 | 67.5 | 280 | 24 | 550 | 580 | 410 | 680 | 1085 | ||||
| 280M | 419 | 1135 | ||||||||||||||||
机座带底脚，端盖上有凸缘(带通孔)IMB35
Frame with feet and end-shield with flange (with plain holes)-IMB35
| 机座号Framesize | 凸缘号Frangecode | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | M | N | S | T | P | AB | AC | AD | HD | L ( | LY,ZJVF) | |||
| 80M | FF165 | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 10 | 165 | 130 | 12 | 3.5 | 200 | 165 | 175 | 130 | 210 | 370 | 423 | |
| 90S | 140 | 70 | 100125 | 56 | 24 | 50 | 8 | 20 | 90 | 180 | 195 | 140 | 230 | 380 | 450 | ||||||||
| 90L | 410 | 475 | |||||||||||||||||||||
| 100L | FF215 | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100112 | 12 | 2151 | 80 | 15 | 4 | 250 | 205 | 215 | 165 | 265 | 465 | 520 | ||
| 112M | 190 | 95 | 140 | 70 | 230 | 240 | 178 | 290 | 480 | 550 | |||||||||||||
| 132S | FF265 | 216 | 108 | 140178 | 89 | 38 | 80 | 10 | 33 | 132 | 2652 | 30 | 300 | 270 | 275 | 210 | 345 | 530 | 620 | ||||
| 132M | 570 | 652 | |||||||||||||||||||||
| 160M | FF300 | 254 | 127 | 210254 | 108 | 42 | 12 | 37 | 160 | 15 | 3002 | 50 | 350 | 320 | 330 | 255 | 420 | 660 | 765 | ||||
| 160L | 715 | 810 | |||||||||||||||||||||
| 180M | 279 | 139.5 | 241279 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 775 | 867 | ||||||||
| 180L | 815 | 905 | |||||||||||||||||||||
| 200L | FF350 | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 350 | 300 | 19 | 5 | 400 | 395 | 420 | 305 | 505 | 850 | 1005 | |||
| 225S | FF400 | 356 | 178 | 286311 | 149 | 60 | 18 | 53 | 225 | 19 | 4003 | 50 | 450 | 435 | 470 | 335 | 560 | 885 | 1035 | ||||
| 225M | 915 | 1060 | |||||||||||||||||||||
| 250M | 406 | 203 | 349 | 168 | 65 | ||||||||||||||||||
| 0 | |||||||||||||||||||||||
| 58 | 250 | 24 | 5004 | 50 | 550 | 490 | 510 | 370 | 615 | 980 | |||||||||||||
| 280S | FF500 | 457 | 228.5 | 368419 | 190 | 75 | 206 | 7.5 | 280 | 550 | 580 | 410 | 680 | 1085 | |||||||||
| 280M | 1135 | ||||||||||||||||||||||
YD系列（IP54)变极多速三相异步电动机YD seres(IP54)electrode-varied multi-speed three phase asynchronous motor
产品概述
Brief introduction of the product
(一)、原理及用途：
YD系列（IP54）变极多速三相异步电动机是Y系列(IP54)三相异步电动机的派生电动机产品，它利用改变定子绕组的接法以改变电动机的极数，从而电动机用一套或两套绕组来获得两种或两种以上的转速。
我厂目前生产的YD系列(IP54)从80\~280机座号11个机座号，共96个规格。
YD系列(IP54)变极多速三相异步电动机的安装尺寸、外形尺寸、绝缘等级、防护等级、冷却方法、结构及安装型式，使用条件、额定电压、额定频率等均与Y2系列(IP54)电动机相同。
YD系列(IP54)变极多速三相异步电动机由于具有可随负载性质的要求而分级变化转速，从而达到了功率的合理匹配和简化了变速系统的特点。它适用于各式切削机床、矿山冶金机械、纺织机械、印染机械、化工机械、农业机械等需要逐级调速的各传动机构。该系列按JB/T7127—1993《YD系列变极多速三相异步电动机技术条件》设计制造。同时还可以生产各种规格电磁制动多速三相异步电动机。
(1)、principie and usage:
YD series (IP54)electrode-varied and multi-speed three-phase asynchronous motor can is derived from Y series(IP54)three-phase asynchronousmotor,It makes use of changing stator winding connection method to change electrode number than gets thedual or more speed by using single or dual windings.
At present we produce 96 specifications,Frame number range from 80\~280 total 11mumbers.
TheYD series(IP54)install size,outline size,insulatingdegree,safetydegree,cooling mode,structure, install mode,application conditions, rating voltage and rating frequency same as yseries.
YD series (IP54) electrode-varied and multi-speed three phase asynchronous motor can change the rev with loading request,therefore,it can efficienty distribut the power and simplify the shift device,This series adapt to every kind of drive machine that need multi-speed,for example,machine tool cutting,mining & metallurgy machinery,spinning machinery,printing and dyeing machinerychemical machinery, agricultural machinery. this series should be made according to the JB/T7127- 1993 《The technical conditions for YD series electrodevaried and multi-speed three phase asynchronous motor》 .We can also produce various kind of specification electromagnetism brake multi-speed three phase asynchronous motor.
(二)、型号说明：
(2)、Model Notes
(三)、YD(IP54)变极多速三相异步电动机接线与标志：
YD系列,<IP54>变极多速三相异步电动机与电源接线按JB/T7127-1993标准的规定。
双速时：低速与电源接线端子为1U、1V、1W（△接）
高速与电源接线端子为2U、2V、2W（2Y接）
(3)YD(IP54)series motor's connection and symbol
Electrode-varied and multi-speed three phase asynchronous moto connect with power conform to JB/T2127-1993. For dual speeds:Terminal IU,IV,IW use for low speed connect with the power(△connect mode)
Terminal 2U,2V,2w use for high speed connect with the power(2Y Connection mode)
High speed(2Y)
技术参数Technical data
| 型号Type | 异步转速AsynchromousSpeed(r/min) | 功率Outputpower(kw) | 额定电流Rated Current(A) | 效率Eff(%) | 功率因数Powerfactor(cOS φ) | 空载噪unloadedNoisedB(A) | 麟unlcadedvibration(mm/s) | 堵转电流额定电流LockedtFullload(fme) | 堵转转矩额定转矩LockedU |
| Fullload)(De)9 | |||||||||
| 同步转速 1500/3000r/min(4/2极)Synchronous Speed 1500/3000r/min(4/2P) | |||||||||
| YD-80M,-4/2 | 1420/2860 | 0.45/0.55 | 1.4/1.5 | 66/65 | 0.74/0.85 | 79 | 1.8 | 6.5/7 | 1.5/1.7 |
| YD-80M,-4/2 | 1420/2860 | 0.55/0.75 | 1.7/2.0 | 68/66 | 0.74/0.85 | 79 | 1.8 | 6.5/7 | 1.6/1.8 |
| YD-90S-4/2 | 1430/2850 | 0.85/1.1 | 2.3/2.8 | 74/71 | 0.77/0.85 | 79 | 1.8 | 6.5/7 | 1.8/1.9 |
| YD-90L-4/2 | 1430/2850 | 1.3/1.8 | 3.3/4.3 | 76/73 | 0.78/0.85 | 83 | 1.8 | 6.5/7 | 1.8/2.0 |
| YD-100L,-4/2 | 1430/2850 | 2/2.4 | 4.8/5.6 | 78/76 | 0.81/0.86 | 87 | 1.8 | 6.5/7 | 1.7/1.9 |
| YD-100L2-4/2 | 1430/2850 | 2.4/3 | 5.6/6.7 | 79177 | 0.83/0.89 | 87 | 1.8 | 6.5/7 | 1.6/1.7 |
| YD-112M-4/2 | 1450/2890 | 3.3/4 | 7.4/8.6 | 82/79 | 0.83/0.89 | 87 | 1.8 | 6.5/7 | 1.9/2.0 |
| YD-132S-4/2 | 1450/2890 | 4.5/5.5 | 9.8/11.9 | 83/79 | 0.84/0.89 | 91 | 1.8 | 6.5/7 | 1.7/1.8 |
| YD-132M-4/2 | 1450/2890 | 6.5/8 | 13.8/17.1 | 84/80 | 0.85/0.89 | 91 | 1.8 | 6.5/7 | 1.7/1.8 |
| YD-160M-4/2 | 1460/2920 | 9/11 | 18.5/22.9 | 87/82 | 0.85/0.89 | 95 | 2.8 | 6.5/7 | 1.6/1.8 |
| YD-160L-4/2 | 1460/2920 | 11/14 | 22.3/28.8 | 87/82 | 0.86/0.90 | 95 | 2.8 | 6.5/7 | 1.7/1.9 |
| YD-180M-4/2 | 1470/2940 | 15/18.5 | 29.4/36.7 | 89/85 | 0.87/0.90 | 95 | 2.8 | 6.5/7 | 1.8/1.9 |
| YD-180L-4/2 | 1470/2940 | 18.5/22 | 35.9/42.7 | 89/86 | 0.88/0.91 | 95 | 2.8 | 6.5/7 | 1.6/1.8 |
| YD-200L-4/2 | 1470/2940 | 26/30 | 49.9/58.3 | 89/85 | 0.89/0.92 | 98 | 2.8 | 6.5/7 | 1.4/1.6 |
| YD-225S-4/2 | 1475/2950 | 32/37 | 59.6/68.7 | 90/86 | 0.89/0.92 | 98 | 2.8 | 6.5/7 | 1.4/1.6 |
| YD-225M-4/2 | 1475/2960 | 37/45 | 68/83 | 91/86 | 0.89/0.92 | 100 | 2.8 | 6.5/7 | 1.6/1.6 |
| YD-250M-4/2 | 1475/2960 | 45/52 | 83/100 | 90/87 | 0.89/0.92 | 100 | 4.5 | 6.5/7 | 1.6/1.6 |
| YD-280S-4/2 | 1480/2965 | 60/72 | 110/132 | 91/88 | 0.90/0.92 | 102 | 4.5 | 6.5/7 | 1.4/1.5 |
| YD-280M-4/2 | 1480/2968 | 72/82 | 131/147 | 91/88 | 0.90/0.93 | 102 | 4.5 | 6.5/7 | 1.4/1.5 |
| 同步转速1000/1500r/min(6/4极)Synchronous Speed 1000/1500r/min(6/4P) | |||||||||
| YD-90S-6/4 | 920/1420 | 0.65/0.85 | 2.3/2.3 | 64/70 | 0.68/0.79 | 75 | 1.8 | 6/6.5 | 1.6/1.4 |
| YD-90L-6/4 | 930/1420 | 0.85/1.1 | 2.8/3.0 | 66/71 | 0.70/0.79 | 75 | 1.8 | 6/6.5 | 1.6/1.5 |
| YD-100L,-6/4 | 940/1440 | 1.3/1.8 | 3.8/4.4 | 74177 | 0.70/0.80 | 78 | 1.8 | 6/6.5 | 1.7/1.4 |
| YD-100L2-6/4 | 940/1440 | 1.5/2.2 | 4.3/5.4 | 75/77 | 0.70/0.80 | 78 | 1.8 | 6/6.5 | 1.6/1.4 |
| YD-112M-6/4 | 960/1440 | 2.2/2.8 | 5.7/6.7 | 78177 | 0.75/0.82 | 82 | 1.8 | 6/6.5 | 1.8/1.5 |
| YD-132S-6/4 | 970/1440 | 3/4 | 7.7/9.5 | 79/78 | 0.75/0.82 | 82 | 1.8 | 6/6.5 | 1.8/1.7 |
技术参数Technical data
| 型号Type | 异步转速AsynchromousSpeed(r/min) | 功率Outputpower(kw) | 额定电流Rated Current(A) | 效率Eff(%) | 功率因数Powerfactor(cos φ) | 空载unloadedNois8dBA) | unloadedvibration(mm/s) | 堵转电流额定电流Lockede tFull load((me) | 堵转转矩额定转矩Locked JD |
| Fullload(fpe) | |||||||||
| YD-132M-6/4 | 970/1440 | 4/5.5 | 9.8/12.3 | 82/80 | 0.76/0.85 | 82 | 1.8 | 6/6.5 | 1.6/1.4 |
| YD-160M-6/4 | 970/1460 | 6.5/8 | 15.1/17.4 | 84/82 | 0.78/0.84 | 86 | 2.8 | 6/6.5 | 1.5/1.5 |
| YD-160L-6/4 | 970/1460 | 9/11 | 20.6/23.4 | 85/83 | 0.78/0.85 | 86 | 2.8 | 6/6.5 | 1.6/1.7 |
| YD-180M-6/4 | 980/1470 | 11/14 | 25.9/29.4 | 85/84 | 0.76/0.85 | 90 | 2.8 | 6/6.5 | 1.6/1.7 |
| YD-180L-6/4 | 980/1470 | 13/16 | 29.4/33.6 | 86/85 | 0.78/0.85 | 90 | 2.8 | 6/6.5 | 1.6/1.7 |
| YD-200L-6/4 | 980/1470 | 18.5/22 | 36.3/42 | 87/86.5 | 0.89/0.92 | 90 | 2.8 | 6/7.0 | 1.6/1.5 |
| YD-225S-6/4 | 980/1475 | 22/28 | 43/54 | 88/86.5 | 0.86/0.87 | 92 | 4.5 | 6.5/7.0 | 1.8/1.8 |
| YD-225M-6/4 | 980/1475 | 26/32 | 50/63 | 88/85.5 | 0.86/0.90 | 92 | 4.5 | 6.5/7.0 | 1.8/1.8 |
| YD-250M-6/4 | 980/1476 | 32/42 | 60/77 | 90/86.5 | 0.87/0.91 | 98 | 4.5 | 6.5/7.0 | 1.5/1.3 |
| YD-280S-6/4 | 980/1480 | 42/55 | 80/102 | 90/87 | 0.87/0.90 | 98 | 4.5 | 6.5/7.0 | 1.5/1.3 |
| YD-280M-6/4 | 980/1480 | 55/67 | 105/126 | 90/87 | 0.87/0.89 | 98 | 4.5 | 6.5/7.0 | 1.6/1.3 |
| 同步转速750/1500r/min(8/4极)Synchronous Speed 750/1500r/min(8/4P) | |||||||||
| YD-90L-8/4 | 700/1420 | 0.45/0.75 | 1.9/1.8 | 58/72 | 0.63/0.87 | 75 | 1.8 | 5/6 | 1.6/1.4 |
| YD-100L-8/4 | 700/1420 | 0.85/1.5 | 3.1/3.5 | 67/74 | 0.63/0.88 | 78 | 1.8 | 5/6 | 1.6/1.4 |
| YD-112M-8/4 | 700/1420 | 1.5/2.4 | 5.0/5.3 | 72178 | 0.63/0.88 | 82 | 1.8 | 5/6 | 1.7/1.7 |
| YD-132S-8/4 | 720/1440 | 2.2/3.3 | 7.0/7.1 | 75/80 | 0.64/0.88 | 82 | 1.8 | 5/6 | 1.5/1.7 |
| YD-132M-8/4 | 720/1440 | 3/4.5 | 9.0/9.4 | 78/82 | 0.65/0.89 | 82 | 1.8 | 5/6 | 1.5/1.6 |
| YD-160M-8/4 | 730/1450 | 5/7.5 | 13.9/15.2 | 83/84 | 0.66/0.89 | 86 | 2.8 | 5/6 | 1.5/1.6 |
| YD-160L-8/4 | 730/1450 | 7/11 | 19.0/21.8 | 85/86 | 0.66/0.89 | 86 | 2.8 | 5/6 | 1.5/1.6 |
| YD-180L-8/4 | 730/1470 | 11/17 | 26.7/32.6 | 87/88 | 0.72/0.91 | 90 | 2.8 | 6/7 | 1.5/1.5 |
| YD-200L,-8/4 | 740/1470 | 14/22 | 33/42.3 | 87/88 | 0.74/0.92 | 92 | 2.8 | 6/7 | 1.8/1.7 |
| YD-200L2-8/4 | 740/1470 | 17/26 | 40/48.8 | 87/88 | 0.74/0.92 | 92 | 2.8 | 6/7 | 1.5/1.7 |
| YD-225M-8/4 | 732/1475 | 24/34 | 52/65 | 89/88 | 0.77/0.88 | 92 | 4.5 | 6/7 | 1.5/1.5 |
| YD-250M-8/4 | 735/1476 | 30/42 | 61/75 | 90/89 | 0.78/0.91 | 94 | 4.5 | 6/7 | 1.6/1.7 |
| YD-280S-8/4 | 737/1480 | 40/55 | 82/100 | 91/90 | 0.80/0.91 | 98 | 4.5 | 6/7 | 1.6/1.7 |
| YD-280M-8/4 | 737/1480 | 47/67 | 95/119 | 91/90 | 0.81/0.92 | 98 | 4.5 | 6/7 | 1.6/1.7 |
技术参数Technical data
| 型号Type | 异步转速AsynchromousSpeed(r/min) | 功率Outputpower(kw) | 额定电流Rated Current(A) | 效率Eff(%) | 功率因数Powerfactor(cos φ) | 空载噪unloadedNoisedB(A) | 麟unloadedvibration(mm/s) | 堵转电流额定电流LockedLotet | 堵转转矩额定转矩LookedLU |
| Fullload(fmude2 | Fulload(fpie)) | ||||||||
| 同步转速 750/1000r/min(8/6极)Synchronous Speed 750/1000r/min(8/6P) | |||||||||
| YD-90S-8/6 | 700/930 | 0.35/0.45 | 1.60/1.40 | 56/70 | 0.60/0.72 | 73 | 1.8 | 5/6 | 1.8/2.0 |
| YD-90L-8/6 | 700/930 | 0.45/0.65 | 1.90/1.90 | 59/71 | 0.60/0.73 | 73 | 1.8 | 5/6 | 1.7/1.8 |
| YD-100L-8/6 | 710/950 | 0.75/1.1 | 2.90/3.10 | 65/75 | 0.60/0.73 | 73 | 1.8 | 5/6 | 1.8/1.9 |
| YD-112M-8/6 | 710/950 | 1.3/1.8 | 4.50/4.80 | 72/78 | 0.61/0.73 | 75 | 1.8 | 5/6 | 1.7/1.9 |
| YD-132S-8/6 | 730/970 | 1.8/2.4 | 5.80/6.20 | 76/80 | 0.62/0.73 | 79 | 1.8 | 5/6 | 1.6/1.9 |
| YD-132M-8/6 | 730/970 | 2.6/3.7 | 8.20/9.40 | 78/82 | 0.62/0.73 | 79 | 1.8 | 5/6 | 1.9/1.9 |
| YD-160M-8/6 | 730/980 | 4.5/6 | 13.3/14.7 | 83/85 | 0.62/0.73 | 83 | 2.8 | 5/6 | 1.6/1.9 |
| YD-160L-8/6 | 730/980 | 6/8 | 17.5/19.4 | 84/86 | 0.62/0.73 | 83 | 2.8 | 5/6 | 1.6/1.9 |
| YD-180M-8/6 | 730/980 | 7.5/10 | 21.9/24.2 | 84/86 | 0.62/0.73 | 83 | 2.8 | 5/6 | 1.9/1.9 |
| YD-180L-8/6 | 730/980 | 9/12 | 24.7/28.3 | 85/86 | 0.65/0.75 | 86 | 2.8 | 5/6 | 1.8/1.8 |
| YD-200L,-8/6 | 730/980 | 12/17 | 32.6/39.6 | 86/87 | 0.65/0.75 | 88 | 2.8 | 5/6 | 1.8/2.0 |
| YD-200L2-8/6 | 730/980 | 15/20 | 40.3/46 | 87/88 | 0.65/0.75 | 88 | 2.8 | 5/6 | 1.8/2.0 |
| 同步转速500/1000r/min(12/6极)Synchronous Speed 500/1000r/min(12/6P) | |||||||||
| YD-160M-12/6 | 480/970 | 2.6/5.0 | 11.6/11.9 | 74/84 | 0.46/0.76 | 79 | 2.8 | 4/6 | 1.2/1.4 |
| YD-160L-12/6 | 480/970 | 3.7/7.0 | 16.1/15.8 | 76/85 | 0.46/0.79 | 83 | 2.8 | 4/6 | 1.2/1.4 |
| YD-180L-12/6 | 490/980 | 5.5/10 | 19.6/20.5 | 79/86 | 0.54/0.86 | 83 | 2.8 | 4/6 | 1.3/1.3 |
| YD-200L,-12/6 | 490/980 | 7.5/13 | 24.5/26.4 | 83/87 | 0.56/0.86 | 86 | 2.8 | 4/6 | 1.5/1.5 |
| YD-200L2-12/6 | 490/980 | 9/15 | 28.9/31.6 | 83/87 | 0.57/0.87 | 86 | 2.8 | 4/6 | 1.5/1.5 |
| YD-225M-12/6 | 482/975 | 12/20 | 33.9/38.9 | 85/88 | 0.61/0.87 | 86 | 4.5 | 4/6 | 1.5/1.5 |
| YD-250M-12/6 | 485/980 | 15/24 | 40.8/45.9 | 86/89 | 0.63/0.87 | 89 | 4.5 | 4/6 | 1.5/1.5 |
| YD-280S-12/6 | 487/985 | 20/30 | 54/57.4 | 88/89 | 0.63/0.87 | 89 | 4.5 | 4/6 | 1.5/1.5 |
| YD-280M-12/6 | 487/985 | 24/37 | 61/66 | 88/89 | 0.65/0.87 | 89 | 4.5 | 4/6 | 1.5/1.5 |
机座不带底脚，端盖上有凸缘(带通孔)-IMB5
Frame without feet and end-shield with flange(with plain holes)-IMB5
机座号(80-200) Frame size
机座号(225-280)Frame size
| 机座号Frame size | 凸缘号Frangecode | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number ofpoles on theflange | 外型尺寸Exterior dimension(mm) | ||||||||||||
| D | E | F | G | M | N | P | R | s | T | AC | AD | HF | L | |||
| 80M | FF165 | 19 | 40 | 6 | 15.5 | 165 | 130 | 200 | 12 | 3.5 | 4 | 175 | 130 | 230 | 295 | |
| 90S | 24 | 50 | 8 | 20 | 195 | 140 | 240 | 320 | ||||||||
| 90L | 345 | |||||||||||||||
| 100L | FF215 | 28 | 60 | 24 | 215 | 180 | 250 | 15 | 4 | 215 | 165 | 290 | 385 | |||
| 112M | 240 | 175 | 300 | 400 | ||||||||||||
| 132S | FF265 | 38 | 80 | 10 | 33 | 265 | 230 | 300 | 275 | 210 | 315 | 470 | ||||
| 132M | 510 | |||||||||||||||
| 160M | FF300 | 42 | 12 | 37 | 300 | 250 | 350 | 0 | 19 | 5 | 300 | 255 | 385 | 615 | ||
| 160L | 670 | |||||||||||||||
| 180M | 48 | 110 | 14 | 42.5 | 380 | 280 | 430 | 700 | ||||||||
| 180L | 740 | |||||||||||||||
| 200L | FF350 | 55 | 16 | 49 | 350 | 300 | 400 | 420 | 305 | 480 | 770 | |||||
| 225S | FF400 | 60 | 18 | 53 | 400 | 350 | 450 | 8 | 470 | 335 | 535 | 815 | ||||
| 225M | 845 | |||||||||||||||
| 250M | FF500 | 65 | 140 | 58 | 500 | 450 | 550 | 510 | 370 | 595 | 910 | |||||
| 280S | 75 | 20 | 67.5 | 580 | 410 | 650 | 985 | |||||||||
| 280M | 1035 | |||||||||||||||
机座带底脚，端盖上无凸缘-IMB3 Frame with feet and end-shield without flange-IMB3
| 机座号Frame size | 安装尺寸 Mouting dimension(mm) | 外型尺寸Exterior dimension(mm) | ||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | AB | AC | AD | HD | L | ||
| 80M | 125 | 62.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 165 | 175 | 130 | 210 | 295 | ||
| 90S | 140 | 70 | 100 | 56 | 24 | 50 | 8 | 20 | 90 | 10 | 180 | 195 | 140 | 230 | 320 | |
| 90L | 125 | 345 | ||||||||||||||
| 100L | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100 | 205 | 215 | 165 | 265 | 385 | |||
| 112M | 190 | 95 | 140 | 70 | 112 | 12 | 230 | 240 | 178 | 290 | 400 | |||||
| 132S | 216 | 108 | 140 | 89 | 38 | 80 | 10 | 33 | 132 | 270 | 275 | 210 | 345 | 470 | ||
| 132M | 178 | 510 | ||||||||||||||
| 160M | 254 | 127 | 210 | 108 | 42 | 12 | 37 | 160 | 15 | 320 | 330 | 255 | 420 | 615 | ||
| 160L | 254 | 670 | ||||||||||||||
| 180M | 279 | 139.5 | 241 | 121 | 48 | 110 | 14 | 42.5 | 180 | 355 | 380 | 280 | 455 | 700 | ||
| 180L | 279 | 740 | ||||||||||||||
| 200L | 318 | 159 | 305 | 133 | 55 | 16 | 49 | 200 | 395 | 420 | 305 | 505 | 770 | |||
| 225S | 356 | 178 | 286 | 149 | 60 | 18 | 53 | 225 | 19 | 435 | 470 | 335 | 560 | 815 | ||
| 225M | 311 | 845 | ||||||||||||||
| 250M | 406 | 203 | 349 | 168 | 65 | 58 | 250 | 24 | 490 | 510 | 370 | 615 | 910 | |||
| 280S | 457 | 228.5 | 368 | 190 | 75 | 20 | 67.5 | 280 | 550 | 580 | 410 | 680 | 985 | |||
| 280M | 419 | 1035 | ||||||||||||||
机座带底脚，端盖上有凸缘(带通孔)-IMB35
Frame with feet and end-shield with flange(with plain holes)-IMB35
机座号(160-200)Frame size
机座号(H80-200)Frame size
机座号(H225-280)Frame size
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 凸缘号Frangecode | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number ofpoles on theflange | 外型尺寸Exterior dimension(mm) | |||||||||||||||||||
| A | A/2 | B | C | D | E | F | G | H | K | M | N | P | R | S | T | AB | AC | AD | HD | L | |||
| 80M | FF165 | 1256 | 2.5 | 100 | 50 | 19 | 40 | 6 | 15.5 | 80 | 101 | 65 | 1302 | 00 | 12 | 3.5 | 4 | 165 | 175 | 130 | 210 | 295 | |
| 90S | 140 | 70 | 100125 | 56 | 24 | 50 | 8 | 20 | 90 | 180 | 195 | 140 | 230 | 320 | |||||||||
| 90L | 345 | ||||||||||||||||||||||
| 100L | FF215 | 160 | 80 | 140 | 63 | 28 | 60 | 24 | 100112 | 215 | 1802 | 50 | 15 | 4 | 205 | 215 | 165 | 265 | 385 | ||||
| 112M | 190 | 95 | 140 | 70 | 230 | 240 | 178 | 290 | 400 | ||||||||||||||
| 132S | FF265 | 2161 | 08 | 140178 | 89 | 38 | 801 | 0 | 33 | 132 | 265 | 230 | 300 | 270 | 275 | 210 | 345 | 470 | |||||
| 132M | 510 | ||||||||||||||||||||||
| 160M | FF300 | 2541 | 27 | 210254 | 108 | 42 | 12 | 37 | 160 | 153 | 002 | 50 | 350 | 0 | 19 | 5 | 320 | 330 | 255 | 420 | 615 | ||
| 160L | 670 | ||||||||||||||||||||||
| 180M | 279 | 279139.5 | 241279 | 121 | 48 | 110 | 144 | 2.51 | 80 | 355 | 380 | 280 | 455 | 700 | |||||||||
| 180L | 740 | ||||||||||||||||||||||
| 200L | FF350 | 3181 | 59 | 305 | 133 | 55 | 16 | 49 | 200 | 350 | 300 | 400 | 395 | 420 | 305 | 505 | 770 | ||||||
| 225S | FF400 | 3561 | 78 | 286311 | 149 | 60 | 18 | 532 | 251 | 94 | 003 | 504 | 50 | 8 | 435 | 470 | 335 | 560 | 815845 | ||||
| 225M | |||||||||||||||||||||||
| 250M | 4062 | 03 | 349 | 168 | 65140 | 58 | 250 | 5004 | 505 | 50 | 490 | 510 | 370 | 615 | 910 | ||||||||
| 280S | FF500 | 457228.5 | 368419 | 190 | 75 | 206 | 7.5 | 280 | 24 | 550 | 580 | 410 | 680 | 9851035 | |||||||||
| 280M | |||||||||||||||||||||||
机座不带底脚，端盖上有凸缘(带螺孔)-IMB14
Frame without feet and end-shield with flange(with plain holes)-IMB14
机座号(80-90) Frame size
机座号(80-112) Frame size
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 凸缘号Frangecode | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number ofpoles on theflange | 外型尺寸Exteror dimension(mm) | ||||||||||||
| D | E | F | G | M | N | P | R | S | T | AC | AD | HF | L | |||
| 80M | FT100 | 19 | 40 | 6 | 15.5 | 100 | 80 | 120 | M6 | 3.0 | 4 | 175 | 130 | 218 | 295 | |
| 90S | FT115 | 24 | 50 | 20 | 115 | 95 | 140 | 0 | M8 | 195 | 140 | 238 | 320 | |||
| 90L | 345 | |||||||||||||||
| 100L | FT130 | 28 | 60 | 8 | 24 | 130 | 110 | 160 | 3.5 | 215 | 165 | 273 | 385 | |||
| 112M | 240 | 178 | 298 | 400 | ||||||||||||
立式安装、机座不带底脚，端盖上有凸缘(带通孔)轴伸向下的电动机-IMV1
机座号(180-200)Frame size
机座号(225-280)Frame size
安装及外型尺寸Mounting and dimensions
| 机座号Frame size | 凸缘号Frangecode | 极数numberofelectrodes | 安装尺寸Mouting dimension(mm) | 凸缘号孔数number of | 外型尺寸Exterior dmension(mm) | ||||||||||||||
| D | E | F | G | M | N | P | R | S | T | poles on theflange | AC | AD | HF | L | |||||
| 180M | FF300 | 4.2 | 48 | 110 | 14 | 42.5 | 300 | 250 | 350 | 0 | 19 | 5 | 4 | 380 | 280 | 500 | 760 | ||
| 180L | 6.4 | 800 | |||||||||||||||||
| 200L | FF350 | 8.4 | 55 | 16 | 49 | 350 | 300 | 400 | 420 | 305 | 550 | 840 | |||||||
| 225S | FF400 | 8.6 | 60 | 140 | 18 | 53 | 400 | 350 | 450 | 8 | 470 | 335 | 610 | 905 | |||||
| 225M | 12.6 | 55 | 110 | 16 | 49 | 910 | |||||||||||||
| 60 | 140 | 18 | 5358 | 935 | |||||||||||||||
| 250M | FF500 | 6.4.2 | 500 | 450 | 550 | 510 | 370 | 650 | 1015 | ||||||||||
| 65 | |||||||||||||||||||
| 280S | 8、4、2 | 580 | 410 | 720 | 1110 | ||||||||||||||
| 75 | 20 | 67.5 | |||||||||||||||||
| 280M | 8、6、4 | 65 | |||||||||||||||||
| 18 | 58 | 1150 | |||||||||||||||||
| 75 | 20 | 67.5 | |||||||||||||||||
2、P尺寸为最大极限值；3、R为凸缘配合面至轴伸肩的距离；4、S孔的位置度公差以轴伸的轴线为基准。
| 机座号Frame size | 尺寸Dimension(mm) | 凸缘号孔数number ofpoles on theflange | 机座号Frame size | 尺寸Dimension(mm) | 凸缘号孔数number ofpoles on theflange | |||||||||||
| P | M | N | S | T | L | P | M | N | S | T | L | |||||
| 71 | 120 | 100 | 80 | 10 | 3 | 245 | 4 | 100 | 160 | 130 | 110 | 10 | 3 | 350 | 4 | |
| 160 | 130 | 110 | 200 | 165 | 130 | 12 | 3.5 | |||||||||
| 140 | 100 | 80 | 236 | 250 | 215 | 180 | 15 | 4 | ||||||||
| 200 | 165 | 130 | 12 | 3.5 | 233 | 300 | 265 | 230 | 315 | |||||||
| 714 | 120 | 100 | 80 | 10 | 3 | 257 | 350 | 300 | 250 | 19 | 5 | 318 | ||||
| 160 | 130 | 110 | 112 | 160 | 130 | 110 | 10 | 3 | 380 | |||||||
| 140 | 100 | 80 | 248 | 200 | 165 | 130 | 12 | 3.5 | ||||||||
| 200 | 165 | 130 | 12 | 3.5 | 245 | 250 | 215 | 180 | 15 | 4 | ||||||
| 80 | 120 | 100 | 80 | 10 | 3 | 278 | 300 | 265 | 230 | 334 | ||||||
| 160 | 130 | 110 | 350 | 300 | 250 | 19 | 5 | |||||||||
| 200 | 165 | 130 | 12 | 3.5 | 132S | 160 | 130 | 110 | 10 | 3 | 425 | |||||
| 140 | 100 | 80 | 10 | 3 | 264 | 200 | 165 | 130 | 12 | 3.5 | ||||||
| 250 | 215 | 180 | 15 | 4 | 246 | 250 | 215 | 180 | 15 | 4 | ||||||
| 300 | 265 | 230 | 300 | 265 | 230 | |||||||||||
| 90S | 120 | 100 | 80 | 10 | 3 | 304 | 350 | 300 | 250 | 386 | ||||||
| 160 | 130 | 110 | 400 | 350 | 300 | 19 | 5 | 388 | ||||||||
| 200 | 165 | 130 | 12 | 3.5 | 450 | 400 | 350 | |||||||||
| 140 | 100 | 80 | 10 | 3 | 301 | 132M | 160 | 130 | 110 | 10 | 3 | 461 | ||||
| 250 | 215 | 180 | 15 | 4 | 280 | 200 | 165 | 130 | 12 | 3.5 | ||||||
| 300 | 265 | 230 | 250 | 215 | 180 | 15 | 4 | |||||||||
| 90L | 120 | 100 | 80 | 10 | 3 | 328 | 300 | 265 | 230 | |||||||
| 160 | 130 | 110 | 350 | 300 | 250 | 19 | 5 | 422 | ||||||||
| 200 | 165 | 130 | 12 | 3.5 | 400 | 350 | 300 | 424 | ||||||||
| 140 | 100 | 80 | 10 | 3 | 325 | 450 | 400 | 350 | ||||||||
| 250 | 215 | 180 | 15 | 4 | 304 | 160M | 200 | 165 | 130 | 12 | 3.5 | 524 | ||||
| 300 | 265 | 230 | 250 | 215 | 180 | 15 | 4 | |||||||||
| 100 | 120 | 100 | 80 | 10 | 3 | 340 | 300 | 265 | 230 | |||||||
| 140 | 100 | 80 | 358 | 350 | 300 | 250 | 19 | 5 | 504 | |||||||
配硬齿面减速机专用电机外形尺寸DIMENSION OF SPECIAL MOTOR FOR SPEED-REDUCING MACHINE
Y2系列(IP54)三相异步电动机 Y2 series (IP54) three-phase asynchronous motor
| 机座号Frame size | 尺寸Dimension(mm) | 凸缘号孔数number ofpoles on theflange | |||||
| P | M | N | S | T | L | ||
| 160M | 400 | 350 | 300 | 19 | 5 | 476 | 4 |
| 450 | 400 | 350 | 567 | ||||
| 550 | 500 | 450 | |||||
| 160L | 200 | 165 | 130 | 12 | 3.5 | 547 | |
| 250 | 215 | 180 | 15 | 4 | |||
| 300 | 265 | 230 | |||||
| 350 | 300 | 250 | 19 | 5 | 519 | ||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 602 | ||||
| 550 | 500 | 450 | |||||
| 180M | 250 | 215 | 180 | 15 | 4 | 583 | |
| 300 | 265 | 230 | 555 | ||||
| 350 | 300 | 250 | 19 | 5 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 583 | ||||
| 550 | 500 | 450 | 635 | ||||
| 180L | 250 | 215 | 180 | 15 | 4 | 616 | |
| 300 | 265 | 230 | 588 | ||||
| 350 | 300 | 250 | 19 | 5 | |||
| 400 | 350 | 300 | |||||
| 机座号Frame size | 尺寸Dimension(mm) | 凸缘号孔数number ofpoles on theflange | |||||
| P | M | N | S | T | L | ||
| 180L | 450 | 400 | 350 | 19 | 5 | 616 | 4 |
| 550 | 500 | 450 | 666 | ||||
| 200L | 300 | 265 | 230 | 15 | 4 | 654 | |
| 350 | 300 | 250 | 19 5 | ||||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 8 | ||||
| 550 | 500 | 450 | 642 | ||||
| 225S | 350 | 300 | 250 | 680 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 674 | ||||
| 550 | 500 | 450 | 669 | ||||
| 225M | 350 | 300 | 250 | 702 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 696 | ||||
| 550 | 500 | 450 | 691 | ||||
| 250M | 400 | 350 | 300 | 771 | |||
| 450 | 400 | 350 | 775 | ||||
| 550 | 500 | 450 | 770 | ||||
| 280S | 550 | 500 | 450 | 828 | |||
| 280M | 550 | 500 | 450 | 879 | |||
| 机座号Frame size | 尺寸Dimension(mm) | 凸线号uiepoles on theflange | |||||
| P | M | N | S | T | L | ||
| 71 | 120 | 100 | 80 | 10 | 3 | 310 | 4 |
| 160 | 130 | 110 | |||||
| 140 | 100 | 80 | |||||
| 200 | 165 | 130 | 12 | 3.5 | 298 | ||
| 80 | 120 | 100 | 80 | 10 | 3 | 369 | |
| 160 | 130 | 110 | |||||
| 200 | 165 | 130 | 12 | 3.5 | |||
| 机座号Frame size | 尺寸Dimension(mm) | 凸线号uier ofpoles on theflange | ||||||
| P | M | N | S | T | L | |||
| 80 | 140 | 100 | 80 | 10 | 3 | 368 | 4 | |
| 250 | 215 | 180 | 15 | 4 | 365 | |||
| 300 | 265 | 230 | ||||||
| 90S | 120 | 100 | 80 | 10 | 3 | 390 | ||
| 160 | 130 | 110 | ||||||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 140 | 100 | 80 | 10 | 3 | 385 | |||
| 机座号Frame size | 尺寸Dimension(mm) | 凸缘号numbr ofpoles on theflange | ||||||
| P | M | N | S | T | L | |||
| 90S | 250 | 215 | 180 | 15 | 4 | 368 | 4 | |
| 300 | 265 | 230 | 360 | |||||
| 90L | 120 | 100 | 80 | 10 | 3 | 417 | ||
| 160 | 130 | 110 | ||||||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 140 | 100 | 80 | 10 | 3 | 414 | |||
| 250 | 215 | 180 | 15 | 4 | 393 | |||
| 300 | 265 | 230 | 385 | |||||
| 100 | 120 | 100 | 80 | 10 | 3 | 446 | ||
| 140 | 100 | 80 | 451 | |||||
| 160 | 130 | 110 | ||||||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 250 | 215 | 180 | 15 | 4 | ||||
| 300 | 265 | 230 | 408 | |||||
| 350 | 265 | 250 | 19 | 5 | 411 | |||
| 112 | 160 | 130 | 110 | 10 | 3 | 482 | ||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 250 | 215 | 180 | 15 | 4 | ||||
| 300 | 265 | 230 | 433 | |||||
| 350 | 300 | 250 | 19 | 5 | ||||
| 132S | 160 | 130 | 110 | 10 | 3 | 530 | ||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 250 | 215 | 180 | 15 | 4 | ||||
| 300 | 265 | 230 | ||||||
| 350 | 300 | 250 | 19 | 5 | 495 | |||
| 400 | 350 | 300 | ||||||
| 450 | 400 | 350 | ||||||
| 132M | 160 | 130 | 110 | 10 | 3 | 568 | ||
| 200 | 165 | 130 | 12 | 3.5 | ||||
| 250 | 215 | 180 | 15 | 4 | ||||
| 300 | 265 | 230 | ||||||
| 350 | 300 | 250 | 19 | 5 | 533 | |||
| 400 | 350 | 300 | 529 | |||||
| 450 | 400 | 350 | ||||||
| 160M | 200 | 165 | 130 | 12 | 3.5 | 638 | ||
| 250 | 215 | 180 | 15 | 4 | ||||
| 机座号Frame size | 尺寸Dimension(mm) | 凸缘号number dpoles on theflange | |||||
| P | M | N | S | T | L | ||
| 160M | 300 | 265 | 230 | 15 | 4 | 638 | 48 |
| 350 | 300 | 250 | 19 | 5 | 618 | ||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 591 | ||||
| 550 | 500 | 450 | |||||
| 160L | 200 | 165 | 130 | 15 | 4 | 683 | |
| 250 | 215 | 180 | |||||
| 300 | 265 | 230 | 5 | ||||
| 350 | 300 | 250 | 663 | ||||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | |||||
| 635 | |||||||
| 550 | 500 | 450 | |||||
| 180M | 250 | 215 | 180 | 15 | 4 | 685 | |
| 300 | 265 | 230 | 666 | ||||
| 350 | 300 | 250 | 19 | 5 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 638 | ||||
| 550 | 500 | 450 | 666 | ||||
| 180L | 250 | 215 | 180 | 15 | 4 | 723 | |
| 300 | 265 | 230 | 703 | ||||
| 350 | 300 | 250 | 19 | 5 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 676 | ||||
| 550 | 500 | 450 | 703 | ||||
| 200L | 300 | 365 | 230 | 15 | 4 | 795 | |
| 350 | 300 | 250 | 19 | 5 | |||
| 400 | 350 | 300 | 782 | ||||
| 450 | 400 | 350 | |||||
| 550 | 500 | 450 | 770 | ||||
| 225S | 350 | 300 | 250 | 19 | 5 | 847 | |
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 840 | ||||
| 550 | 500 | 450 | 835 | ||||
| 225M | 350 | 300 | 250 | 872 | |||
| 400 | 350 | 300 | |||||
| 450 | 400 | 350 | 865 | ||||
| 550 | 500 | 450 | 860 | ||||
| 250M | 400 | 350 | 300 | 932 | |||
| 450 | 400 | 350 | 936 | ||||
| 550 | 500 | 450 | 931 | ||||
电机常见故障及排除方法FREQUENT MALFUNCTIONS AND SOLUTIONS
| 故障 | 可能的原因 | 检查或校正方法 |
| 1、电动机在空载时不能启动 | 1、馈电路断线（三相当中的一根）2、定子三相绕组中一相断路（“Y”形连接时）3、电源电压或频率不对 | 检查电源电压和个别连接处。检查保险丝，馈电线内电流和每一相绕组的电阻。检查电压及频率。 |
| 2、电动机在负载时不能启动，在低负载或空载时能启动，但在负载增加后转速即大跌或甚至停下来 | 1、电源电压低2、定子绕组有匝间短路3、定子三相绕组中一相断线（“△”接法时）4、过载 | 检查线路电压。检查每相绕组和每相空载电流。检查每相绕组电阻。检查负载。 |
| 3、电机停留在低转速 | 1、定子绕组一相接反，电动机发响声2、转子端环和导杆中间有断裂情况 | 检查馈电线的电流和引出线标记。检查短路电流。 |
| 4、定子过热 | 1、馈电线路三根中有一根断线或定子绕组一相断路2、电源电压过大在或过低3、过载4、定子匝间或相间短路5、通风不好 | 检查保险丝，线间电压和导线电流。检查线间电压和导线电流。检查馈电线内的电流，检查定子相间和对地绝缘电阻。检查绕组电阻。检查通风孔道。 |
| 5、轴承过热 | 1、装配不对2、电动机轴与被拖动之轴不平行3、没有润滑油，油内有杂物或油质不良4、皮带过紧5、不平衡的磁性吸力大 | 检查转子是否容易转动。校正两轴平行。用汽油洗刷更换润滑油。松皮带或移动底脚。检查空气隙偏心度。 |
| 6、合闸时保险设备动作 | 1、定子绕组一相接反2、把应当接成“Y”形的定子三相绕组接成子“△”形3、绕组对机座短路或相间短路 | 检查引出线标记和接法。检查引出线标记和接法。检查各相绕组对机座的绝缘以及相间绝缘。 |
| 7、机械振动大 | 1、转子不平衡只在相当低的转数时才不振动2、轴向窜动大3、传动皮带接头接得不好4、皮带轮不平衡 | 检查平衡情况。检查轴承外的间隙，并加以调整。重新接皮带。检查皮带轮。 |
注：电动机的故障及产生故障的原因很多，有时一个故障可能有几个原因，一个原因也可以产生几种故障。上表所列仅为常见的几种，在检查如发生疑问可参阅有关检修维护书或与制造厂联系。
Note:There are many reasons for the malfunctions.Sometimes there might be several reasons for one problem.Sometimes one reason might came several problem.These listed in the table are just those frequent appeared.please don't hesitate to contact us while in need.
其他产品OTHER
洗车机减速机系列The Reducer Of Car Wash Equipment
JCM
VSF75
JCQY
可选色方案
嘉诚可提供丰富的产品可选颜色方案，可选色包含：交通黄、朱红、银灰色、信号白、龙胆蓝色、(详见下图)。客户可根据自身不同需求选择相应产品颜色。
油漆涂装
全新涂层选用符合国家环保要求的绿色油漆产品。油漆中不含VOC、TDI、苯/甲苯、二甲苯、重金属等有毒有害物质。且具有超强的附着力、耐候性、耐腐蚀性。能适用普通室外中等腐蚀环境和各类室内工况。并有增强型涂层体系适应重腐蚀环境。
