Sndway激光测距仪使用手册 - 电子书在线预览、各类电子书在线制作-云展网平台

SW-210GT SW-211GT

手持式双向绿光测距仪

Dual Green Laser Distance Meter

中文

English

01~18

19~37

安全条例

初次使用仪器前，请先仔细阅读安全条款和操作指南

在使用仪器之前请仔细阅读本手册中的所有操作指南和

安全条例，没有按照本手册所指引的操作方法使用仪器

有可能会造成仪器的损害、影响测量精度、对使用者或

第三者的人身伤害。

不要用任何方式自行打开或修理仪器，严禁非法改装或

改变仪器激光发射器的性能。请妥善保管仪器，不要放

置在儿童可以接触到的地方，避免无关人员的使用。

严禁用仪器激光器照射自已或他人的眼睛及身体其他部

位，严禁将激光器照射在高反光的物体表面上。

仪器电磁辐射可能对其他设备和装置造成干扰，请不要

在飞机或医疗设备附近使用本仪器，不要在易燃、易爆

的环境中使用仪器。

报废的仪器不可与生活垃圾一同处理，请按国家或者当

地的相关法律规定处理报废仪器。

仪器出现任何的质量问题，或对使用仪器有任何疑问时

请及时联系当地经销商或深达威仪器厂家，我们将第一

时间为您解决。

感谢您购买手持式激光测距仪系列产品！

- 01 -

显示屏、键盘

显示屏

- 02 - 120.00

60.000 60.000

90.0°

开机/

测量键

关机/

清除键

累加/累减/

锁屏键

电量指示

长度/面积/

体积/三角

测量模式

基准指示

激光指示

角度指示

测量模式

单位键/

测量基准键

辅显示区

单位

水平泡

屏幕锁定

指示

主显示区

键盘

基本功能

启动仪器和关闭仪器

单位设定

在长度待测模式下，长按键，进入测量单位调整状

态，该仪器提供了6种单位可供选择。

关机状态下，长按键3秒，仪器启动，仪器进入待

测模式。

开机状态下，长按键3秒关闭仪器。180秒内未对仪

器进行任何操作，仪器将自动关闭。

测量单位：

长度面积体积

0.000 m

0.00 ft

0'00\" 1/16

0 1/16 in

0.0 in

0.00 m

0.000 m2

0.00 ft2

0.00 m2

0.000 m3

0.00 ft3

0.00 m3

- 03 -

短按键，进入模式选择，显示如下：

短按键，切换模式；

短按键，选择模式；

短按键，返回；

测量模式选择

测量基准设定

短按键进行测量基准设置，系统默认基准为双向

测量。

向右后基准

向左前基准向左后基准

双向测量

FUN

RECORD

- 04 -

仪器支持自动转屏，长按键，锁定屏幕方向，屏幕

显示【】图标，再长按键，取消屏幕方向锁定。

仪器共有九种模式选择：

长度模式测角求高模式

求直角三角形高度

求直角三角形斜边

求三角形底边和

求直角三角形辅助高

面积模式

体积模式

墙面面积模式

转屏与锁定

- 05 -

仪器附带电子水平泡，可测量平面的水平度。

电子水平泡

机身背部带磁，可吸附金属表面。

强磁吸附

- 06 -

底部带磁，超强吸附

带磁性可固定有磁性的物体

0°

仪器内置倾角传感器，可以实时测量底边和侧边两面的

角度

角度测量

- 07 -

45°

45.0°

45°

通过短按键，修改自助校准数值;

声音开关与自助校准

按住键，再按键开机，屏幕亮起后，立即

松开键，等到屏幕显示“Sound”后，松开键，

进入声音设置。

1.声音设置：

通过切换声音开(on)关(off)；短按键保存

设置并进入自助校准。

声音调整结束后，进入前端调整，短按键进入后

端调整，后端调整完成，短按进入测量界面。

2.自助校准：

自助校准分两步，先调前端数值(仪器顶部靠近显示屏

处发射激光)，再调后端数值(仪器底部靠近按键发射激

光)，可调整范围：-0.009m至+0.009m，操作方法如下：

长度模式下按键，仪器激光发射，锁定测量点。

再按键进行单次距离数据的测量，测量结果显在

主显示区；双向测量时，辅显示区显示左右两端距离。

长度模式下长按键，进入连续测量状态，屏幕显示

实时测量数据，最大值，最小值；短按键或键

退出连续测量模式。

距离测量、面积，体积，勾股间接测量

累加，累减测量

长度模式-单次测量：

长度模式-连续测量：

- 08 -

3.自助校准使用举例：假设实际距离为3.780m

将仪器设置为向左后基准，测得3.778m,比实际值小2mm，

则将前端数值调整为+0.002m；

若测得3.783m,比实际值大3mm，则将前端数值调整

为-0.003m；

将仪器设置为向右后基准，测得3.778m,比实际值小2mm，

则将后端数值调整为+0.002m；

若测得3.783m,比实际值大3mm，则将后端数值调整

为-0.003m。

中点寻找：将基准调至双向基准，长按键开启连续

测量，根据以下提示，寻找中间点。

横屏：

1.屏幕显示【←】，请向左移动

2.屏幕显示【→】，请向右移动

竖屏：

1.屏幕显示【↑】，请向上移动

2.屏幕显示【↓】，请向下移动

- 09 -

屏幕显示时，表示当前处于中点位置。

2.339m 2.339m

墙面面积测量：

按键，测得墙面的高度；

按键，测得墙面1的宽度1；

按键，测得墙面2的宽度2；

仪器会自动计算墙面的面积=高度x宽度1；

仪器会自动计算墙面的面积总和

面积总和=高度 x（宽度1+宽度2）

依次类推，按键，测得墙面n的宽度n；

辅助显示区显示长方形的长和宽的测量值。在测量过

程中，还可以键入清除本次测量结果重新测量。

面积测量：

按键进行第一条边的测量(长)

按键进行第二条边的测量(宽)

按键进行第一条边的测量(长)

按键进行第二条边的测量(宽)

按键进行第三条边的测量(高)

在测量过程中，还可以键入清除本次测量结果重

新测量。

仪器会自动进行体积运算，结果显示在主显示区。辅

助显示区显示立方体的长宽高的测量值。

- 10 -

体积测量：

测角求高 (如图一所示)

勾股定理间接测量：

按键，依屏幕提示先测出斜边长度(a)

（图一）（屏幕示意图）

仪器同时测出斜边与底边夹角。

在测量过程中，还可以键入清除本次测量结果重

新测量。

面积总和=高度 x（宽度1+宽度2+......+宽度n）；

仪器自动计算水平距离 b与垂直高度。h

- 11 -

（图四）（图五）

（图二）（图三）

按键，依屏幕提示先测出一条边的长度(a)

按键，再测出一条直角边长度(b)

测量直角三角形斜边 (如图三所示)

测量直角三角形高度 (如图二所示)

仪器会在第二次测量结束后，自动计算三角形的斜边(x）

按键，依屏幕提示先测出一条斜边长度(a)

按键，再测出另外一条斜边长度(b)

按键，最后测出直角边长度(c)

测量三角形底边和 (如图四所示)

仪器在测量结束后，自动计算三角形的高(x）

按键，依屏幕提示先测出斜边长度(a)

按键，再测出直角边长度(b)

仪器会在第二次测量结束后，自动计算三角形的高(h)

- 12 -

加减测量功能：

1.长度累加减

短按键，屏幕测量主显示区出现“+”，进入累加

测量模式，继续测量，仪器会自动累加

长度模式下，测量

一组数据

短按键,进入

累加模式

再测量数据，仪器会

自动累加求和

勾股测量模式，直角边必须小于斜边长度仪器才能计算，

否则仪器会显示错误信号提示。在勾股测量模式下，为

保证测量的精度，须确保从同一个起始点测量，并按斜

边、直角边测量顺序测量。

按键，依屏幕提示先测出一条斜边长度(a)

按键，再测出另一条边长度(b)

按键，最后测出另一条斜边长度(c)

测量三角形辅助高 (如图五所示)

仪器在测量结束后，自动计算三角形的辅助线的高度(x）

在累加模式下，再短按键，屏幕测量主显示区出现

“-”，进入累减测量模式，继续测量，仪器会自动累减

- 13 -

2.面积、体积累加减

体积累加减和面积累加减操作相同，此处以面积累加

为例：

面积累减：在第一步，短按键先进入累加，再短按

切换至累减模式，之后的操作和累加类似，不再复述。

多次累加/减运算：

在第二步，求得第二次面积之后，再次短按键，

可以继续累加/减下一个面积，最后按照第三步，求得

结果

第一步，测量一次面积(如图 )

第二步，短按键，屏幕测量主显示区出现“+”，

进入累加测量模式，然后测量第二次面积(如图 )

图 1 图 2 图 3

第三步，短按键，仪器自动求出两次面积的和

(如图 ) 3

- 14 -

仪器测量完成，自动存储结果；

记录

充电

仪器显示，表示电量不足，建议用户立即充电，

以免影响测量精度。

长按键查看记录；短按键前后翻看记录；

长按键，清除所有记录。

充电请使用DC5V ≥1A输出的合规充电器，建议使用手

机充电器。

电池保养：长时间不使用，建议先把仪器充满电，并

每半年再充电一次，以免电池放电损坏

充电指示：仪器滚动显示，表示未充满。显示

，且不再滚动，则表示充满。

- 15 -

提示信息

角度传感器错误返厂进行维修

信息原因解决方法

对电池进行充电

让仪器在指定环境中使用

测量反射能力弱的目标点

信号过弱测量反射能力强的目标点

信号过强

电池电压过低

超出工作温度范围

Err5 勾股测量违规重新测量，确保斜边大于直角边

Err6

Err4

Err3

Err2

Err1

Err 超出距离测量范围让仪器在量程范围内使用

使用过程中，主显示区可能会出现如下提示信息：

- 16 -

技术参数

*“d”表示实际距离

** 在恶劣环境下，比如阳光过于强烈、环境温度波动过大、反射

面反射效果较弱、电池电量不足等情况下，测量结果会有较大的

误差，此种情况配合目标反射板使用效果更佳。

0˚C~40˚C

-20˚C~60˚C

单向5500次；双向3500次

180秒

20秒

100笔

500-800nm <1mW

±(2mm+d

*万分之一)*（单向）

20%~80%RH

3.7V 850mAh锂电池

±90˚

项目

118x54x25.5mm

最大测量距离

距离测量精度

连续测量功能

面积体积测量

勾股测量功能

测角测高功能

长度加减测量

最大/最小值

激光等级

激光类型

存储记录笔数

自动切断激光

自动关机

背光时间 60秒

满电工作时间

存储温度范围

工作温度范围

存储湿度

充电规格 DC5V 0.75A Type-C

电池规格

充电时长约1.5小时

倾角测量范围

外形尺寸

60m(单向)120m(双向) 100m(单向)200m(双向)

SW-210GT SW-211GT

- 17 -

墙面面积测量

电子水平泡

自动转屏

磁吸

检验员：日期：

挂绳

布包盒

主机

彩盒

保修合格证

说明书

USB Type-C线

7 条

本

张

条

项目名称单位数量备注

个

台

仪器日常保养

装箱清单

禁止将仪器长期放置在高温高湿的环境中储存，长

期不使用仪器时，请把仪器放置在随机的仪器套内

放在阴凉干爽处存放。

请保持仪器表面清洁，可用湿的软布擦拭表面灰尘，

不可用带有腐蚀性洗液清洁仪器。可按照擦拭光学

器件表的方法擦拭激光器窗口和聚焦镜。

购买仪器时请按下列清单认真检查仪器所有附件是否

完整?

- 18 -

8 反光板仅100米以上有

Safety Regulations

Please read the safety regulations and operation guide

carefully before operating.

Please read all of the operational guide and safety regulations

in this manual before operation . Improper operations without

complying with this manual may cause damage to the device,

influence on measurement result or cause personal injury to

the user or a third party.

The instrument is not allowed to disassemble or repair in any

ways. It is forbidden to do any illegal modification or

performance change for laser emitter. Please keep it out of

reach of children and avoid being used by any irrelevant person.

It is strictly prohibited to shoot eyes or other parts of body with

the laser. It is not allowed to take the laser to shoot the surface

of any highly reflective objects.

Due to electromagnetic radiation interference to other

equipment and devices, please don't use the meter in the plane

or around medical equipment, don’t use it in inflammable,

explosive environment.

Discarded meter device should not be processed just like

household garbage, please handle it in line with related law and

regulations.

Any quality issues or any questions on the meter, please contact

local distributors or manufacturer in time, we are ready to offer

solutions for you.

- 19 -

Screen/Keys

Screen

- 20 -120.00 60.000 60.000

90.0°

Screen lock

indication Measuring

mode

Angle

indication

Laser

indication

Measuring

reference

indication

Battery level

indication

Main display

area

Power-on

Add/Subtract

/Lock screen

Power-off/

Clear

Level bubble

Auxiliary

display area

Unit/

Measuring

reference

Length/Area/

Volume/

Triangulation

measuring

mode

Unit

Keys

0.000 m

0.00 ft

0'00\" 1/16

01/16 in

0.0 in

0.00 m

0.000 m2

0.00 ft2

0.00 m2

0.000 m3

0.00 ft3

0.00 m3

Main Functions

Turn on/off the Instrument

In the off state, long press for 3 seconds to start

the instrument, and the instrument enters the test mode.

In the on state, long press for 3 seconds to turn off

the instrument. If no operation is performed within 180

seconds, the instrument will shut down automatically.

Unit Setting

Length Area Volume

In the mode of length measuring, long press to enter

the page of measuring units. The instrument provides 6

optional units.

Measuring units:

- 21 -

Press to enter mode selection, and the screen will

display as follows:

Press to switch mode;

Press to select mode;

Press to return;

Turn on/off the Instrument

Press to set the measurement reference. The default

benchmark is bidirectional measurement.

Left-forward datum

Right-back datum Bidirectional measurement

Left-back datum

Selection of Measuring Mode

- 22 -

The instrument supports automatic screen rotation.

Long press to lock the screen direction, and the

screen displays【】. Long press again to cancel

the screen orientation lock.

The instrument provides 9 optional modes：

Length mode Calculate height by

measuring angle

Calculate height of

right triangle

Calculate hypotenuse

of right triangle

Calculate the sum of

the sides of triangle

Calculate the

auxiliary height of

right triangle

Area mode

Volume mode

Wall area mode

Screen Rotation and Lock

- 23 -

The instrument is equipped with an electronic level

bubble to measure the levelness of the plane.

Electronic Level Bubble

The back of the instrument is magnetic, so that the

instrument can be adsorbed on the metal surface.

Strong Magnetic Adsorption

A magnetic object

can be fixed by the

strong magnetism

- 24 -

0°

The instrument has built-in tilt sensor, which can

measure the angle between the base and the two

planes of the instrument in real time.

Angle Measuring

45°

45.0°

45°

- 25 -

Press and hold key and press key to start.

When the screen lights up, release key immediately.

When \"Sound\" appears on the screen, release key.

to enter the sound setting.

Switch the sound on/off by pressing or ;

Press key to save the settings and enter the

self-calibration.

The self-calibration is divided into two steps: first adjust

the front-end value (laser emission at the top of the

instrument near the display), and then adjust the

back-end value (laser emission at the bottom of the

instrument near the button). The adjustment range is:

-0.009m to +0.009m. Operation is as follows:

Short press or key to modify the self-calibration

value;

2. Self-calibration

1. Sound Setting

Sound &Self-calibration

Length Mode-Single Measurement :

Distance/Area/Volume/Pythagorean

/Add/Subtract Measurement

Press in length mode, and the instrument emits

laser to lock the measuring point. Then press for

a single distance measurement, and the measurement

results will be displayed in the main display area. In

bidirectional measurement, the auxiliary display area

displays the distance between the left and right ends.

Length Mode-Single Measurement :

Long press in length mode to enter continuous

measurement mode. The screen displays the real-time

measurement data, maximum value, and minimum

- 26 -

3. Example of Self-calibration：

The actual distance is 3.780m.

Set the instrument to the left back reference, if the

measured value is 3.778m, 2mm less than the actual

value, then adjust the front-end value to +0.002m.

If the measured value is 3.783m, 3mm larger than the

actual value, then adjust the front-end value to -0.003m;

Set the instrument to the right back reference, if the

measured value is 3.778m, 2mm less than the actual

value, then adjust the back-end value to +0.002m,

If the measured value is 3.783m, 3mm larger than the

actual value, then adjust the back-end value to -0.003m.

After the sound setting, enter the front-end adjustment;

Short press key to enter the back-end adjustment.

After the back-end adjustment is complete, press

key to enter the measurement interface.

value. Press or to exit the continuous

measurement mode.

Look for the midpoint: set the reference to bidirectional

reference, long press to start continuous

measurement. Follow these tips to look for the middle

point.

Landscape screen:

1. If 【←】is displayed on the screen, please move to

the left

2. If【→】is displayed on the screen, please move to

the right

Portrait screen:

1. If【↑】is displayed on the screen, please move up

2. If【↓】is displayed on the screen, please move down

If is displayed on the screen, the current position is

the midpoint.

- 27 -

2.339m 2.339m

Press to measure the first side (length)

Press to measure the second side (width)

Press to measure the third side (height)

The instrument can calculate volume automatically and

display the results in the main display area. The auxiliary

display area displays measured value of the length, width

and height of the cube.

In the measurement process, user can press to

clear the measurement results and measure again.

Volume Measurement :

Press the to measure the height of the wall;

Press to measure the width 1 of wall 1;

The instrument will automatically calculate the wall

area = height x width 1;

Press to measure the width 2 of wall 2;

Wall area measurement :

Area Measurement :

Press to measure the first side (length)

Press to measure the second side (width)

The auxiliary display area displays measured values of

the length and width of the rectangle. In the

measurement process, user can press to clear the

measurement results and measure again.

- 28 -

The instrument will calculate the total area of the wall

automatically.

Total Area = Height x (Width 1+ Width 2)

By analogy, press to measure the width of the wall n;

Total Area = Height x (Width 1+ Width 2+...... + Width n);

In the measurement process, user can press to

clear the measurement results and measure again.

Press to measure the length of the hypotenuse (a)

according to the screen prompt.

The instrument will simultaneously measure the angle θ

between the hypotenuse and the base.

The instrument automatically calculates the horizontal

distance b and the vertical height h.

Calculate height by measuring angle (as shown

in Figure 1)

Pythagorean Measurement :

- 29 -

Figure 1 Screen

(Figure 2) (Figure 3)

Press to measure the length of the hypotenuse (a)

according to the screen prompt.

Press to measure the length of the right angle (b).

The instrument will automatically calculate the height (h)

of the triangle after the second measurement.

Measure the height of right triangle (as shown

in Figure 2)

Press to measure the length of the side (a)

according to the screen prompt.

Press to measure the length of the leg (b)

Measure the hypotenuse of right triangle (as

shown in Figure 3)

- 30 -

The instrument will automatically calculate the hypotenuse

(×) of the triangle after the second measurement,

Press to measure the length of the hypotenuse (a)

according to the screen prompt.

Press to measure the length of another hypotenuse

(b)

Press to measure the length of the leg (c)

The instrument will automatically calculates the height (x)

of the triangle after the measurement.

Measure the sum of triangle base (as shown in

Figure 4)

Press to measure the length of the hypotenuse (a)

according to the screen prompt.

Press to measure the length of the side (b).

Press to measure the length of the other

hypotenuse (c).

After measurement, the instrument will automatically

calculate the height (×) of the auxiliary line of the triangle.

Measuring triangle auxiliary height (as shown in

Figure 5)

(Figure 4) (Figure 5)

- 31 -

Addition and Subtraction Measurement

Press to enter the

addition mode

1、Length Addition and Subtraction

2、Area/Volume Addition and Subtraction

Short press , \"+\" appears in the main display area of

the screen, and the instrument enters the addition

measurement mode. If the instrument continues to

measure, it will automatically add up the measured value.

In the addition mode, press again, \"-\" appears in

the main display area of the screen, and the instrument

enters the subtraction measurement mode. If the

instrument continues to measure, the instrument will

automatically subtract the measured value.

The operation of adding and subtracting volume is the

same as that of area. Here, take area addition and

subtraction as an example:

Measure a set of data

in length mode

When measuring again, the

instrument will automatically

add up the data and sum it up

In the Pythagorean measurement mode, the length of

the leg of the triangle must be less than the hypotenuse,

otherwise the instrument will give an error prompt. To

ensure the accuracy of measurement, make sure to

measure from the same starting point, and in the order

of hypotenuse and legs.

- 32 -

Step 1: Measure the area once (Figure 1)

Step 2: Press , \"+\" appears in the main display area

of the screen, and the instrument enters the addition

measurement mode. Then measure the area for the

second time (Figure 2).

Step 3: Press and the instrument will automatically

calculate the sum of two areas (Figure 3).

Area addition: In the first step, press to enter the

addition mode first. Then press to switch to the

subtraction mode. The subsequent operation is similar

to the addition mode.

Multiple add/subtract operations:

In the step 2, after the second area is obtained, short

press again to continue adding/subtracting the next

area. Finally, according to the step 3, the result is

obtained.

(Figure 1) (Figure 2) (Figure 3)

- 33 -

Records

After the measurement is completed, the instrument

automatically stores the results.

Long press to view records; Short press

to view the record forward or backward;

Long press to clear all records.

Charging

If the instrument shows , it means the battery is

low. It is recommended that users charge it immediately

to avoid affecting the measurement accuracy.

Use a compliant charger with DC5V ≥1A output for

charging. Phone chargers are recommended.

Charging indication: If flashes, it means that the

battery is not fully charged. If is displayed and

is no longer rolling, the battery is fully charged.

Battery maintenance: If not used for a long time, it is

recommended to fully charge the instrument and

charge it once every six months to avoid battery

discharge damage.

- 34 -

Err5

Err6

Err4

Err3

Err2

Err1

Err

Prompt Information

During use, the following prompt information may be

displayed in the main display area:

Out of measuring

range Use the instrument within the

measurement range

Measure the target point with

strong reflectivity

Measure the target point with

weak reflectivity

Charge the battery

Use the instrument in the specified

environment

Remeasure, ensure the hypotenuse

is longer than the right side

Return to factory for repair

Weak signal

Strong signal

Low battery voltage

Out of operating

temperature range

Wrong Pythagorean

measurement

Angle sensor failure

Info Cause Solution

- 35 -

-20˚C~60˚C

500-800nm <1mW

±(2mm+D*1/10000)*(Unidirectional)

20%~80%RH

3.7V 850mAh Li-ion

±90˚

118x54x25.5mm

DC5V 0.75A Type-C

SW-210GT SW-211GT

Specifications

Measuring range

Accuracy

Dip measuring range

60m(Unidirectional)

120m(Bidirectional)

100m(Unidirectional)

200m(Bidirectional)

Item

Continuous measurement

Area/Volume measurement

Wall area measurement

Pythagorean measurement

Max/Min value

Electronic level bubble

Automatic screen rotation

Magnetism

Laser level

Laser type

Max storage 100 units

Auto laser-off 20s

Auto power-off 180s

Backlight time 60s

Battery

Charging specification

Charge time About 1.5 hours

Storage temperature

Working temperature 0˚C~40˚C

Storage humidity

Dimension

5500 times (Unidirectional);

3500 times (Bidirectional)

Operation times at full

charge

Angle and height

measurement

Length addition/subtraction

measurement

- 36 -

* \"d\" indicates the actual distance.

** In harsh environment, such as: the sunlight is too strong, the

ambient temperature fluctuates excessively, the reflection effect

of the object's surface is weak and the battery is low, the

measurement results will have a large error, so a reflecting plate

is needed.

Maintenance

Packing List

It is forbidden to store the instrument in a high

temperature and humid environment for a long time.

When the instrument is not used for a long time, please

put the instrument in a cloth box and store it in a dry

and cool place.

Please keep the surface of the instrument clean. User

can wipe the dust with a damp soft cloth. Do not

clean the instrument with corrosive liquid. The laser

window and focusing mirror can be wiped in the same

way as the optical device.

When purchasing the instrument, please check carefully

whether all accessories are complete according to the

following list.

Item Name Unit QTY Note

Meter

Pouch

Strap

User manual

Color box

Type-C cable PC

- 37 -

1 1

7 Reflector PC 1

Just available for 100m

Sndway Technology (Guangdong) Co., LTD

全国咨询服务热线/ Service Hotline：400-125-6969

深达威科技（广东）股份有限公司

Add: Sndway Science & Technology Industrial Park, 58

Tuanjie Road, Humen 523930, Dongguan, China

地址：东莞市虎门镇虎门团结路58号深达威科技园

电话 / Tel：0769-85265688

网址/ Web：www.sndway.com

邮箱/E-mail：market@sndway.com

快速跳转到指定页