该页无缩略图
柯尼塞格跑车遥控灯光安装教程
Installation tutorial for Koenigsegg Sports Car RemoteControl Lights
0
2
③
未安装前请先检测灯饰。
安装时，需要先将积木拼好，再按照灯饰说明书进行操作，替换部分零件即可完成。
由于灯饰全部采用0.3毫米导线，非常细，请勿用力拉扯或多次弯折，安装灯条过程中轻拿轻放。
Pleasecheck the lightingbefore installing it.
0
③
When installing，you need to follow the instructions.Replace somepartstocomplete. Since the lighting ismade entirely of O.3 mmwire,it is very thin,pleasedon't pull ithard orDonotbendmultiple times and gently handle during the installation of the light bar.
灯光材料如下
The lighting materials are as follows
拿出A包灯光和配件
Take out the lights and accessories in Package A
将车头积木拆起
Take the building blocks at the front of the car apart
拿出灯线和配件将第1颗灯粒安装如下
Take out the lamp wire and accessories and install the first lamp particle as follows
如图，安装下面的灯粒
As shown in the picture，install the following lamp grains
把两端的积木件也拆起
Take apart the buildingblocks at both ends as well
将灯粒和配件安装如下
Install the lamp grains and accessories as follows
拿出另一边，同样方式安装灯粒和配件
Take out the other side and install the lamp beads and accessories in the same way
积木件还原
Restoration of buildingblocks
多余导线藏于积木内
The extra wires are hidden inside the building blocks
积木件安装还原并还原积木
Install and restore the building blocks
灯光插头穿过积木
The light plug passes through the building blocks
积木还原
Buildingblock restoration
拿出B包灯光
Take out the B package of lights
将灯条安装如下
Install the light strip as follows
积木打开，将灯条穿过
Open the building blocks and pass the light strips through
安装第2节灯条
Install Section 2of the light strip
安装第3节灯条
Install Section3 of thelight strip
将灯条插头穿过积木到副驾驶位置
Pass the light bar plug through the building block to the passenger seat
拿出C包灯光
Take out the C package of lights
将车子翻转
Turn the car over
将2节灯条如图安装到车底两侧
Install the two sections of light strips on both sides of the vehicle as shown in the picture
剩下的灯光导线穿过积木
The remaining light wires pass through the building blocks
最后1节灯光安装在车头底部
The last section of light is installed at the bottom of the front of the vehicle
灯光插头穿过积木到副驾驶位置
The light plug passes through the building blocks to the passengerseat
拿出D包灯光
Take out the light from the D package
将第1节灯条安装如下
Install the first section of the light strip as follows
剩下的灯光导线穿过积木
The remaining light wires pass through the building blocks
将第2节灯条从另一侧穿过积木
Pass the light strip of Section 2 through the building block from the other side
安装如下
Install as follows
将第3节灯条穿过积木如下
Pass the light strip of Section 3 through the building blocks as follows
把积木打开，灯条安装如下
Open the building blocks and install the light strips as follows
灯光插头穿过积木
The light plug passes through the building blocks
拿出E包灯光和配件
Take out the e-pack lights and accessories
将第1节和第2节红灯灯条安装如下
Install the red light strips of Section 1 and Section 2 as follows
把红圈的积木拆起
Take apart the buildingblocks circled in red
将多余的导线藏于积木内
Hide the extra wires inside the building blocks
积木还原
Buildingblock restoration
将剩下的灯粒穿过积木
'ass the remaining light particles through the building blocks
把积木拆起
Take the building blocks apart
拿出配件，将2颗灯粒放配件内安装如下
Take out the accessories and install the two lamp particles inside as follows
将灯光插头延箭头方向穿过
Pass the light plug through the direction of the arrow
拿出F包灯光
Take out the F-pack light
将第1节红灯灯条按照如下
Arrange the red light strip of Section 1 as follows
将剩下的灯光导线延箭头方向穿过
Pass the remaining light wires along the direction of the arrow
把积木拆起
Take the building blocks apart
将第2节红灯灯条安装如下
Install the red light strip in Section 2 as follows
把积木拆起，将导线穿过
lake the building blocks apart and pass the wires through them
将第3节红灯灯条安装如下
Install the red light strip in Section 3as follows
积木安装还原
Buildingblockinstallationrestoration
将最后一节灯光导线穿过积木
Pass the last section of the light wire through the building blocks
安装最后1节灯条
Install the last light strip
将灯光插头延箭头穿过积木
'ass the light plug along the arrow through the building block
拿出G包灯光
Take out the G package oflights
将第1节灯条安装在后轮上如图
Install the first section of the light strip on the rear wheel as shown in the picture
将剩下的灯光导线延箭头方向穿过
Pass the remaining light wires along the direction of the arrow
安装另一节灯条
Install another light strip
灯光插头延箭头穿到副驾驶位置
'he light plug extends along the arrow to the passenger seat
拿出H包灯光
Take out the Hbag light
把积木拆起
Take the buildingblocks apart
将第1节灯条安装如下
Install the first section of the light strip as follows
灯光导线全部穿过积木并还原
All the light wires pass through the building blocks and return to their original state
先将灯光插头延箭头方向穿到副驾驶位置
First，insert the light plug along the direction of the arrow to the passenger seat
将剩下的灯光导线延箭头穿过
Pass the remaining light wires along the arrow
安装最后1节灯条
Install the last light strip
把积木拆起，将多余导线藏于积木内固定
Take the building blocks apart and hide the extra wires inside them to fix them
