该页无缩略图
399
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-RN3-06002 6 0.2 10 20 5.5 60 6 1 ●
SA300-RN3-06002A 6 0.2 10 40 5.5 80 6 1 ●
SA300-RN3-06010 6 1 10 20 5.5 60 6 1 ●
SA300-RN3-06010A 6 1 10 30 5.5 75 6 1 ●
SA300-RN3-06010B 6 1 10 40 5.5 80 6 1 ●
SA300-RN3-06020 6 2 10 20 5.5 60 6 1 ●
SA300-RN3-06020A 6 2 10 40 5.5 80 6 1 ●
SA300-RN3-08002 8 0.2 10 30 7.5 75 8 1 ●
SA300-RN3-08002A 8 0.2 10 50 7.5 90 8 1 ●
SA300-RN3-08010 8 1 10 30 7.5 75 8 1 ●
SA300-RN3-08010A 8 1 10 40 7.5 80 8 1 ●
SA300-RN3-08010B 8 1 10 50 7.5 90 8 1 ●
SA300-RN3-08020 8 2 10 30 7.5 75 8 1 ●
SA300-RN3-08020A 8 2 10 50 7.5 90 8 1 ●
SA300-RN3-10002 10 0.2 12 30 9.5 75 10 1 ●
SA300-RN3-10002A 10 0.2 12 50 9.5 90 10 1 ●
SA300-RN3-10010 10 1 12 30 9.5 75 10 1 ●
SA300-RN3-10010A 10 1 12 40 9.5 80 10 1 ●
SA300-RN3-10010B 10 1 12 50 9.5 90 10 1 ●
SA300-RN3-10020 10 2 12 30 9.5 75 10 1 ●
3 Flutes, Corner Radius, with Long Neck
SA300-RN3
Helix
◎ Most Suitable ○ Suitable
Fig1
Recommended Cutting Data ※ P659
Please refer to P201 for guidelines to icons
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤32 0
-0.03
SHANK
h6 Helix
30
400
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-RN3-10020A 10 2 12 50 9.5 90 10 1 ●
SA300-RN3-10030 10 3 12 30 9.5 75 10 1 ●
SA300-RN3-10030A 10 3 12 40 9.5 80 10 1 ●
SA300-RN3-10030B 10 3 12 50 9.5 90 10 1 ●
SA300-RN3-12002 12 0.2 14 50 11.5 100 12 1 ●
SA300-RN3-12002A 12 0.2 14 70 11.5 120 12 1 ●
SA300-RN3-12010 12 1 14 40 11.5 90 12 1 ●
SA300-RN3-12010A 12 1 14 50 11.5 100 12 1 ●
SA300-RN3-12010B 12 1 14 60 11.5 110 12 1 ●
SA300-RN3-12010C 12 1 14 70 11.5 120 12 1 ○
SA300-RN3-12020 12 2 14 50 11.5 100 12 1 ●
SA300-RN3-12020A 12 2 14 70 11.5 120 12 1 ●
SA300-RN3-12030 12 3 14 40 11.5 90 12 1 ●
SA300-RN3-12030A 12 3 14 50 11.5 100 12 1 ●
SA300-RN3-12030B 12 3 14 60 11.5 110 12 1 ●
SA300-RN3-12030C 12 3 14 70 11.5 120 12 1 ●
SA300-RN3-16002 16 0.2 18 50 15.5 100 16 1 ●
SA300-RN3-16002A 16 0.2 18 70 15.5 120 16 1 ●
SA300-RN3-16010 16 1 18 50 15.5 100 16 1 ○
SA300-RN3-16010A 16 1 18 60 15.5 110 16 1 ●
3 Flutes, Corner Radius, with Long Neck
SA300-RN3
Helix
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P659
Please refer to P201 for guidelines to icons
Helix
Fig1
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤32 0
-0.03
SHANK
h6 Helix
30
Continued
401
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-RN3-16010B 16 1 18 70 15.5 120 16 1 ●
SA300-RN3-16010C 16 1 18 80 15.5 130 16 1 ●
SA300-RN3-16020 16 2 18 60 15.5 110 16 1 ●
SA300-RN3-16030 16 3 18 50 15.5 100 16 1 ●
SA300-RN3-16030A 16 3 18 60 15.5 110 16 1 ●
SA300-RN3-16030B 16 3 18 70 15.5 120 16 1 ○
SA300-RN3-16030C 16 3 18 80 15.5 130 16 1 ●
SA300-RN3-16040 16 4 18 60 15.5 110 16 1 ●
SA300-RN3-16050 16 5 18 60 15.5 110 16 1 ●
SA300-RN3-16050A 16 5 18 80 15.5 130 16 1 ○
SA300-RN3-20002 20 0.2 24 60 19 110 20 1 ●
SA300-RN3-20002A 20 0.2 24 80 19 130 20 1 ●
SA300-RN3-20010 20 1 24 60 19 110 20 1 ●
SA300-RN3-20010A 20 1 24 80 19 130 20 1 ○
SA300-RN3-20010B 20 1 24 50 19 100 20 1 ●
SA300-RN3-20010C 20 1 24 70 19 120 20 1 ●
SA300-RN3-20010D 20 1 24 90 19 140 20 1 ○
SA300-RN3-20010E 20 1 24 100 19 150 20 1 ●
SA300-RN3-20020 20 2 24 60 19 110 20 1 ●
SA300-RN3-20030 20 3 24 60 19 110 20 1 ○
3 Flutes, Corner Radius, with Long Neck
SA300-RN3
Helix
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P659
Please refer to P201 for guidelines to icons
Fig1
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤32 0
-0.03
SHANK
h6 Helix
30
Continued
402
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-RN3-20030A 20 3 24 80 19 130 20 1 ●
SA300-RN3-20030B 20 3 24 50 19 100 20 1 ○
SA300-RN3-20030C 20 3 24 70 19 120 20 1 ●
SA300-RN3-20030D 20 3 24 90 19 140 20 1 ○
SA300-RN3-20030E 20 3 24 100 19 150 20 1 ●
SA300-RN3-20040 20 4 24 60 19 110 20 1 ●
SA300-RN3-20050 20 5 24 60 19 110 20 1 ○
SA300-RN3-20050A 20 5 24 80 19 130 20 1 ○
SA300-RN3-20050B 20 5 24 100 19 150 20 1 ●
SA300-RN3-25010 25 1 30 80 24 135 25 1 ●
SA300-RN3-25010A 25 1 30 100 24 155 25 1 ●
SA300-RN3-25010B 25 1 30 125 24 180 25 1 ●
SA300-RN3-25020 25 2 30 80 24 135 25 1 ●
SA300-RN3-25030 25 3 30 80 24 135 25 1 ●
SA300-RN3-25030A 25 3 30 100 24 155 25 1 ○
SA300-RN3-25030B 25 3 30 125 24 180 25 1 ●
SA300-RN3-32030 32 3 40 100 31 163 32 1 ●
SA300-RN3-32030A 32 3 40 120 31 183 32 1 ●
3 Flutes, Corner Radius, with Long Neck
SA300-RN3
Helix
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P659
Please refer to P201 for guidelines to icons
Fig1
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤32 0
-0.03
SHANK
h6 Helix
30
Continued
403
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-BN2-06020 6 3 10 20 5.5 60 6 1 ●
SA300-BN2-06030 6 3 10 30 5.5 75 6 1 ●
SA300-BN2-06040 6 3 10 40 5.5 80 6 1 ○
SA300-BN2-08030 8 4 10 30 7.5 75 8 1 ●
SA300-BN2-08040 8 4 10 40 7.5 80 8 1 ●
SA300-BN2-08050 8 4 10 50 7.5 90 8 1 ○
SA300-BN2-10030 10 5 12 30 9.5 75 10 1 ○
SA300-BN2-10040 10 5 12 40 9.5 80 10 1 ●
SA300-BN2-12040 12 6 14 40 11.5 90 12 1 ●
SA300-BN2-12050 12 6 14 50 11.5 100 12 1 ○
SA300-BN2-12060 12 6 14 60 11.5 110 12 1 ○
SA300-BN2-16060 16 8 18 60 15.5 110 16 1 ●
SA300-BN2-16070 16 8 18 70 15.5 120 16 1 ●
SA300-BN2-20060 20 10 24 60 19 110 20 1 ○
SA300-BN2-20080 20 10 24 80 19 130 20 1 ○
2 Flutes, Ballnose
SA300-BN2
SHANK
h6 Helix
30
◎ Most Suitable ○ Suitable
Fig1
Recommended Cutting Data ※ P659
Please refer to P201 for guidelines to icons
2
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤20 0
-0.03
404
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
Order No. D Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-SN4-06030 6 24 30 5.5 60 6 1 ●
SA300-SF-SN4-08040 8 32 40 7.5 64 8 1 ●
SA300-SF-SN4-10050 10 40 50 9.5 80 10 1 ●
SA300-SF-SN4-12040 12 30 40 11.5 83 12 1 ●
SA300-SF-SN4-12062 12 48 62 11.5 100 12 1 ●
SA300-SF-SN4-16051 16 40 51 15.5 93 16 1 ●
SA300-SF-SN4-16082 16 64 82 15.5 125 16 1 ●
SA300-SF-SN4-20063 20 50 63 19 108 20 1 ●
SA300-SF-SN4-200A2 20 80 102 19 150 20 1 ●
4 Flutes, Square with Long Neck (Side Milling Finishing)
SA300-SF-SN4
SHANK
h6
Fig1
4 Helix Square
38 /41
405
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Please refer to P201 for guidelines to icons
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
●Stock ○Available Upon Order
Order No. D Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-IC-SN4-12040 12 30 40 11.5 83 12 1 ○
SA300-SF-IC-SN4-12062 12 48 62 11.5 100 12 1 ○
SA300-SF-IC-SN4-16051 16 40 51 15.5 93 16 1 ○
SA300-SF-IC-SN4-16082 16 64 82 15.5 125 16 1 ○
SA300-SF-IC-SN4-20063 20 50 63 19 108 20 1 ○
SA300-SF-IC-SN4-200A2 20 80 102 19 150 20 1 ○
4 Flutes, Square with Long Neck (Side Milling Finishing) (Coating with Coolant)
SA300-SF-IC-SN4
SHANK
h6
Fig1
4 Helix Square
Titanium- 40 rich
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
406
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
●Stock ○Available Upon Order
4 Flutes, Corner Radius, with Long Neck (Side Milling Finishing)
SA300-SF-RN4
SHANK
h6
Fig1
4 Helix
38 /41
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-RN4-10030 10 3 40 50 9.5 80 10 1 ○
SA300-SF-RN4-12005 12 0.5 30 40 11.5 83 12 1 ●
SA300-SF-RN4-12005A 12 0.5 48 62 11.5 100 12 1 ○
SA300-SF-RN4-12020 12 2 30 40 11.5 83 12 1 ●
SA300-SF-RN4-12020A 12 2 48 62 11.5 100 12 1 ●
SA300-SF-RN4-12030 12 3 30 40 11.5 83 12 1 ●
SA300-SF-RN4-12030A 12 3 48 62 11.5 100 12 1 ○
SA300-SF-RN4-12040 12 4 30 40 11.5 83 12 1 ●
SA300-SF-RN4-12040A 12 4 48 62 11.5 100 12 1 ●
SA300-SF-RN4-12050 12 5 30 40 11.5 83 12 1 ●
SA300-SF-RN4-16020 16 2 40 51 15.5 93 16 1 ●
SA300-SF-RN4-16020A 16 2 64 82 15.5 125 16 1 ●
SA300-SF-RN4-16030 16 3 40 51 15.5 93 16 1 ●
SA300-SF-RN4-16030A 16 3 64 82 15.5 125 16 1 ●
SA300-SF-RN4-16040 16 4 40 51 15.5 93 16 1 ●
SA300-SF-RN4-16040A 16 4 64 82 15.5 125 16 1 ●
SA300-SF-RN4-16050 16 5 40 51 15.5 93 16 1 ●
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
407
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
●Stock ○Available Upon Order
4 Flutes, Corner Radius, with Long Neck (Side Milling Finishing)
SA300-SF-RN4
SHANK
h6
Fig1
4 Helix
38 /41
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-RN4-20030 20 3 50 63 19 108 20 1 ●
SA300-SF-RN4-20030A 20 3 80 102 19 150 20 1 ●
SA300-SF-RN4-20040 20 4 50 63 19 108 20 1 ●
SA300-SF-RN4-20040A 20 4 80 102 19 150 20 1 ●
SA300-SF-RN4-20050 20 5 50 63 19 108 20 1 ●
SA300-SF-RN4-20050A 20 5 80 102 19 150 20 1 ●
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
Continued
408
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
4 Flutes, Corner Radius, with Long Neck (Side Milling Finishing) (Coating with Coolant)
SA300-SF-IC-RN4
SHANK
h6
Fig1
4 Helix
40
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
●Stock ○Available Upon Order
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-IC-RN4-12005 12 0.5 30 40 11.5 83 12 1 ○
SA300-SF-IC-RN4-12020 12 2 30 40 11.5 83 12 1 ○
SA300-SF-IC-RN4-12020A 12 2 48 62 11.5 100 12 1 ○
SA300-SF-IC-RN4-12030 12 3 30 40 11.5 83 12 1 ●
SA300-SF-IC-RN4-12030A 12 3 48 62 11.5 100 12 1 ●
SA300-SF-IC-RN4-12040 12 4 30 40 11.5 83 12 1 ○
SA300-SF-IC-RN4-12040A 12 4 48 62 11.5 100 12 1 ○
SA300-SF-IC-RN4-12050 12 5 30 40 11.5 83 12 1 ○
SA300-SF-IC-RN4-16020 16 2 40 51 15.5 93 16 1 ○
SA300-SF-IC-RN4-16020A 16 2 64 82 15.5 125 16 1 ○
SA300-SF-IC-RN4-16030 16 3 40 51 15.5 93 16 1 ●
SA300-SF-IC-RN4-16030A 16 3 64 82 15.5 125 16 1 ●
SA300-SF-IC-RN4-16040 16 4 40 51 15.5 93 16 1 ○
SA300-SF-IC-RN4-16040A 16 4 64 82 15.5 125 16 1 ○
SA300-SF-IC-RN4-16050 16 5 40 51 15.5 93 16 1 ○
Titaniumrich
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
409
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
4 Flutes, Corner Radius, with Long Neck (Side Milling Finishing) (Coating with Coolant)
SA300-SF-IC-RN4
SHANK
h6
Fig1
4 Helix
40
Unit (mm)
D Tolerance
6≤D≤20 -0.02
-0.04
●Stock ○Available Upon Order
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-SF-IC-RN4-20030 20 3 50 63 19 108 20 1 ●
SA300-SF-IC-RN4-20030A 20 3 80 102 19 150 20 1 ●
SA300-SF-IC-RN4-20040 20 4 50 63 19 108 20 1 ○
SA300-SF-IC-RN4-20040A 20 4 80 102 19 150 20 1 ○
SA300-SF-IC-RN4-20050 20 5 50 63 19 108 20 1 ○
SA300-SF-IC-RN4-20050A 20 5 80 102 19 150 20 1 ○
Titaniumrich
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
Continued
410
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
6 Flutes, Corner Radius, with Long Neck (Face Milling Finishing)
SA300-WF-RN6
SHANK
h6
Fig1
Helix
30 6
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-WF-RN6-16030 16 3 16 42 15.5 92 16 1 ●
SA300-WF-RN6-16030A 16 3 16 65 15.5 115 16 1 ●
SA300-WF-RN6-16040 16 4 16 65 15.5 115 16 1 ●
SA300-WF-RN6-20030 20 3 20 52 19 104 20 1 ●
SA300-WF-RN6-20030A 20 3 20 73 19 125 20 1 ●
SA300-WF-RN6-20040 20 4 20 73 19 125 20 1 ●
SA300-WF-RN6-25030 25 3 25 52 24 110 25 1 ●
SA300-WF-RN6-25030A 25 3 25 72 24 130 25 1 ●
SA300-WF-RN6-25030B 25 3 25 92 24 150 25 1 ●
SA300-WF-RN6-25040 25 4 25 72 24 130 25 1 ●
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Unit (mm)
D Tolerance
16≤D≤25 -0.02
-0.05
●Stock ○Available Upon Order
Please refer to P201 for guidelines to icons
411
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎
6 Flutes, Corner Radius, with Long Neck (Face Milling Finishing) (Coating with Coolant)
SA300-WF-IC-RN6
SHANK
h6
Fig1
Helix
30
Unit (mm)
D Tolerance
16≤D≤25 -0.02
-0.05
●Stock ○Available Upon Order
6
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
SA300-WF-IC-RN6-16030 16 3 16 42 15.5 92 16 1 ○
SA300-WF-IC-RN6-16030A 16 3 16 65 15.5 115 16 1 ●
SA300-WF-IC-RN6-16040 16 4 16 65 15.5 115 16 1 ○
SA300-WF-IC-RN6-20030 20 3 20 52 19 104 20 1 ●
SA300-WF-IC-RN6-20030A 20 3 20 73 19 125 20 1 ●
SA300-WF-IC-RN6-20040 20 4 20 73 19 125 20 1 ○
SA300-WF-IC-RN6-25030 25 3 25 52 24 110 25 1 ●
SA300-WF-IC-RN6-25030A 25 3 25 72 24 130 25 1 ●
SA300-WF-IC-RN6-25030B 25 3 25 92 24 150 25 1 ●
SA300-WF-IC-RN6-25040 25 4 25 72 24 130 25 1 ○
Titaniumrich
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
412
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎ ◎ ◎
Order No. D Lc R L1 L d Drawing
No. In Stock
DNM100-RS1-02001 2 6 0.1 8 50 4 1 ●
DNM100-RS1-02002 2 6 0.2 8 50 4 1 ●
DNM100-RS1-02003 2 6 0.3 8 50 4 1 ○
DNM100-RS1-03001 3 6 0.1 8 50 4 1 ●
DNM100-RS1-03002 3 6 0.2 8 50 4 1 ●
DNM100-RS1-03003 3 6 0.3 8 50 4 1 ○
1 Flutes, Corner Radius
DNM100-RS1
●Stock ○Available Upon Order
SHANK
h6
◎ Most Suitable ○ Suitable
Fig1
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
Unit (mm)
D Tolerance
D≤3 ±0.02
413
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎ ◎ ◎
Order No. D Lc R L1 L d Drawing
No. In Stock
DNM100-RS2-04001 4 6 0.1 8 50 6 1 ●
DNM100-RS2-04002 4 6 0.2 8 50 6 1 ●
DNM100-RS2-04005 4 6 0.5 8 50 6 1 ○
DNM100-RS2-06001 6 10 0.1 20 75 6 1 ●
DNM100-RS2-06002 6 10 0.2 20 75 6 1 ●
DNM100-RS2-06003 6 10 0.3 20 75 6 1 ○
DNM100-RS2-06005 6 10 0.5 20 75 6 1 ○
DNM100-RS2-08001 8 15 0.1 30 75 10 1 ●
DNM100-RS2-08002 8 15 0.2 30 75 10 1 ○
DNM100-RS2-08005 8 15 0.5 30 75 10 1 ●
DNM100-RS2-08010 8 15 1 30 75 10 1 ●
DNM100-RS2-10001 10 15 0.1 35 75 10 1 ○
DNM100-RS2-10002 10 15 0.2 35 75 10 1 ●
DNM100-RS2-10005 10 15 0.5 35 75 10 1 ●
DNM100-RS2-10010 10 15 1 35 75 10 1 ●
DNM100-RS2-10020 10 15 2 35 75 10 1 ○
2 Flutes, Corner Radius
DNM100-RS2
●Stock ○Available Upon Order
SHANK
h6
◎ Most Suitable ○ Suitable
Fig1
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
Unit (mm)
D Tolerance
D≤20 ±0.02
2
414
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/Alloy
Steel (<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum
Alloy Copper Alloy Graphite
◎ ◎ ◎
Order No. D Lc R L1 L d Drawing
No. In Stock
DNM100-RS3-10001 10 15 0.1 35 75 10 1 ●
DNM100-RS3-10002 10 15 0.2 35 75 10 1 ●
DNM100-RS3-10005 10 15 0.5 35 75 10 1 ●
DNM100-RS3-10010 10 15 1 35 75 10 1 ○
DNM100-RS3-10020 10 15 2 35 75 10 1 ○
DNM100-RS3-12002 12 15 0.2 40 75 12 1 ●
DNM100-RS3-12005 12 15 0.5 40 75 12 1 ●
DNM100-RS3-12010 12 15 1 40 75 12 1 ●
DNM100-RS3-12020 12 15 2 40 75 12 1 ○
DNM100-RS3-16002 16 15 0.2 45 100 16 1 ●
DNM100-RS3-16005 16 15 0.5 45 100 16 1 ●
DNM100-RS3-16010 16 15 1 45 100 16 1 ●
DNM100-RS3-16020 16 15 2 45 100 16 1 ○
DNM100-RS3-16030 16 15 3 45 100 16 1 ○
3 Flutes, Corner Radius
DNM100-RS3
●Stock ○Available Upon Order
SHANK
h6
◎ Most Suitable ○ Suitable
Fig1
Recommended Cutting Data ※ P660
Please refer to P201 for guidelines to icons
Unit (mm)
D Tolerance
D≤20 ±0.02
415
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Order No. D Lc L d Drawing No. In Stock
SG200-S2-00401 0.4 0.8 50 4 1 ○
SG200-S2-00802 0.8 2 50 4 1 ●
SG200-S2-01003 1 3 50 4 1 ●
SG200-S2-01504 1.5 4 50 4 1 ●
SG200-S2-02006 2 6 50 4 1 ●
SG200-S2-02008 2 8 75 4 1 ○
SG200-S2-03009 3 9 50 4 1 ●
SG200-S2-03012 3 12 75 4 1 ●
SG200-S2-63009 3 9 50 6 1 ○
SG200-S2-04011 4 11 50 4 2 ●
SG200-S2-04016 4 16 75 4 2 ○
SG200-S2-64011 4 11 50 6 1 ○
SG200-S2-05013 5 13 50 6 1 ○
SG200-S2-05020 5 20 100 6 1 ○
SG200-S2-06016 6 16 50 6 2 ○
SG200-S2-06025 6 25 100 6 2 ○
SG200-S2-08020 8 20 60 8 2 ●
SG200-S2-10025 10 25 75 10 2 ○
SG200-S2-12030 12 30 75 12 2 ○
2 Flutes, Standard Length, Square
SG200-S2
Fig1
Fig2
●Stock ○Available Upon Order
Square
2 SHANK
h6
U-DIA Helix
40 °
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P661
416
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Fig1
Fig2
2 Flutes, Square with Long Neck
SG200-SN2
●Stock ○Available Upon Order
Order No. D Lc d2 L1 L d Drawing
No. In Stock
SG200-SN2-01005 1 3 0.95 5 50 4 1 ●
SG200-SN2-01006 1 3 0.96 6 50 4 2 ●
SG200-SN2-01020 1 3 0.95 20 60 4 1 ●
SG200-SN2-01510 1.5 6 1.44 10 50 4 1 ●
SG200-SN2-01520 1.5 6 1.44 20 60 4 1 ●
SG200-SN2-02015 2 8 1.92 15 50 4 1 ●
SG200-SN2-02020 2 8 1.92 20 50 4 1 ○
SG200-SN2-02030 2 8 1.92 30 75 4 1 ●
SG200-SN2-03015 3 12 2.9 15 50 4 1 ●
SG200-SN2-03030 3 12 2.9 30 75 4 1 ●
SG200-SN2-04020 4 16 3.9 20 50 4 2 ●
SG200-SN2-04025 4 16 3.9 25 75 4 2 ●
SG200-SN2-04040 4 16 3.9 40 75 4 2 ●
SG200-SN2-05030 5 20 4.9 30 75 6 1 ○
SG200-SN2-06030 6 24 5.9 30 75 6 2 ○
SG200-SN2-06040 6 24 5.9 40 75 6 2 ●
SG200-SN2-08040 8 25 7.9 40 100 8 2 ○
SG200-SN2-10040 10 25 9.8 40 100 10 2 ●
SG200-SN2-12040 12 25 11.8 40 100 12 2 ○
SG200-SN2-12060 12 25 11.8 60 100 12 2 ○
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
Recommended Cutting Data ※ P661
Please refer to P201 for guidelines to icons
Square
2 SHANK
h6
U-DIA Helix
40 °
◎ Most Suitable ○ Suitable
417
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Order No. D Lc L d Drawing No. In Stock
SG200-S3-01003 1 3 50 4 1 ○
SG200-S3-01504 1.5 4 50 4 1 ●
SG200-S3-01506 1.5 6 60 4 1 ○
SG200-S3-02006 2 6 50 4 1 ●
SG200-S3-02010 2 10 60 4 1 ●
SG200-S3-03009 3 9 50 4 1 ●
SG200-S3-03015 3 15 60 4 1 ●
SG200-S3-63009 3 9 50 6 1 ○
SG200-S3-04011 4 11 50 4 2 ●
SG200-S3-04020 4 20 75 4 2 ○
SG200-S3-64011 4 11 50 6 1 ●
SG200-S3-05013 5 13 50 6 1 ○
SG200-S3-06016 6 16 50 6 2 ●
SG200-S3-06018 6 18 75 6 2 ○
SG200-S3-06025 6 25 100 6 2 ○
SG200-S3-08020 8 20 60 8 2 ●
SG200-S3-08035 8 35 100 8 2 ○
SG200-S3-10025 10 25 75 10 2 ●
SG200-S3-10040 10 40 100 10 2 ○
SG200-S3-12030 12 30 75 12 2 ○
3 Flutes, Standard Length, Square
SG200-S3
●Stock ○Available Upon Order
Helix
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
Recommended Cutting Data ※ P661
Please refer to P201 for guidelines to icons
Square
SHANK
h6
U-DIA Helix
40 °
◎ Most Suitable ○ Suitable
Fig1
Fig2
418
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
Order No. D Lc L d Drawing No. In Stock
SG200-S4-02006 2 6 50 4 1 ●
SG200-S4-02010 2 10 60 4 1 ●
SG200-S4-03009 3 9 50 4 1 ●
SG200-S4-03015 3 15 60 4 1 ●
SG200-S4-63009 3 9 50 6 1 ○
SG200-S4-04011 4 11 50 4 2 ●
SG200-S4-04020 4 20 75 4 2 ●
SG200-S4-64011 4 11 50 6 1 ●
SG200-S4-05013 5 13 50 6 1 ●
SG200-S4-06016 6 16 50 6 2 ●
SG200-S4-06025 6 25 100 6 2 ●
SG200-S4-08020 8 20 60 8 2 ●
SG200-S4-08025 8 25 100 8 2 ●
SG200-S4-10025 10 25 75 10 2 ●
SG200-S4-10040 10 40 100 10 2 ○
SG200-S4-12030 12 30 75 12 2 ●
SG200-S4-12045 12 45 100 12 2 ○
4 Flutes, Standard Length, Square
SG200-S4
Fig1
Fig2
●Stock ○Available Upon Order
4 Square
SHANK
h6
U-DIA
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P661
Please refer to P201 for guidelines to icons
Helix
40 °
419
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Order No. D Lc R L d Drawing No. In Stock
SG200-R4-02002 2 3.5 0.2 50 4 1 ○
SG200-R4-02005 2 3.5 0.5 60 4 1 ○
SG200-R4-03002 3 4 0.2 50 4 1 ●
SG200-R4-03005 3 4 0.5 75 4 1 ●
SG200-R4-03010 3 4 1 75 4 1 ●
SG200-R4-04002 4 6 0.2 50 4 2 ●
SG200-R4-04010 4 6 1 50 4 2 ●
SG200-R4-05003 5 7 0.3 50 6 1 ○
SG200-R4-06005 6 9 0.5 50 6 2 ●
SG200-R4-06010 6 9 1 50 6 2 ○
SG200-R4-08005 8 12 0.5 60 8 2 ○
SG200-R4-08010 8 12 1 60 8 2 ○
SG200-R4-10005 10 15 0.5 75 10 2 ○
SG200-R4-10010 10 15 1 75 10 2 ○
SG200-R4-12005 12 18 0.5 75 12 2 ○
SG200-R4-12010 12 18 1 75 12 2 ○
SG200-R4-16010 16 36 1 100 16 2 ●
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
4 Flutes, Corner Radius
SG200-R4
Fig1
Fig2
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
SHANK
h6
U-DIA Helix
40 °
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P661
Please refer to P201 for guidelines to icons
420
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Order No. D Lc R d2 L1 L d Drawing
No. In Stock
SG200-RN4-02002 2 3.5 0.2 1.92 6 50 4 1 ●
SG200-RN4-02003 2 3.5 0.3 1.92 30 60 4 1 ●
SG200-RN4-02005 2 3.5 0.5 1.92 30 60 4 1 ●
SG200-RN4-03002 3 4 0.2 2.9 10 50 4 1 ●
SG200-RN4-03003 3 4 0.3 2.9 20 50 4 1 ○
SG200-RN4-03005 3 4 0.5 2.9 20 75 4 1 ○
SG200-RN4-03010 3 4 1 2.9 20 75 4 1 ●
SG200-RN4-04002 4 6 0.2 3.9 20 75 4 2 ●
SG200-RN4-04005 4 6 0.5 3.9 20 50 4 2 ●
SG200-RN4-04010 4 6 1 3.9 20 50 4 2 ●
SG200-RN4-06005 6 9 0.5 5.9 25 75 6 2 ●
SG200-RN4-06010 6 9 1 5.9 25 75 6 2 ●
SG200-RN4-08005 8 12 0.5 7.9 30 100 8 2 ●
SG200-RN4-08010 8 12 1 7.9 30 100 8 2 ●
SG200-RN4-10005 10 15 0.5 9.8 45 100 10 2 ●
SG200-RN4-10010 10 15 1 9.8 35 100 10 2 ●
SG200-RN4-12005 12 18 0.5 11.8 40 100 12 2 ●
SG200-RN4-12010 12 18 1 11.8 40 100 12 2 ●
4 Flutes, Corner Radius, with Long Neck
SG200-RN4
Fig1
Fig2
●Stock ○Available Upon Order
Unit (mm)
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
SHANK
h6
U-DIA Helix
40 °
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P661
Please refer to P201 for guidelines to icons
421
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
U-DIA Helix
30 °
Order No. D R Lc L d Drawing No. In Stock
SG200-B2-00502 0.5 0.25 2 50 4 1 ●
SG200-B2-00602 0.6 0.3 2 50 4 1 ●
SG200-B2-00803 0.8 0.4 3 50 4 1 ○
SG200-B2-01002 1 0.5 2 50 4 1 ●
SG200-B2-01503 1.5 0.75 3 50 4 1 ●
SG200-B2-02004 2 1 4 50 4 1 ●
SG200-B2-02006 2 1 6 60 4 1 ●
SG200-B2-03006 3 1.5 6 50 4 1 ●
SG200-B2-03008 3 1.5 8 60 4 1 ●
SG200-B2-04008 4 2 8 50 4 2 ●
SG200-B2-04016 4 2 16 60 4 2 ●
SG200-B2-05010 5 2.5 10 50 6 1 ○
SG200-B2-06012 6 3 12 50 6 2 ●
SG200-B2-08014 8 4 14 60 8 2 ●
SG200-B2-10018 10 5 18 75 10 2 ●
SG200-B2-12022 12 6 22 75 12 2 ●
2 Flutes, Ballnose
SG200-B2
Fig1
Fig2
●Stock ○Available Upon Order
SHANK
h6
Unit (mm)
D Tolerance
R＜3 0
-0.02
3≤R≤6 0
-0.03
2
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
422
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Order No. D R Lc d2 L1 L d Drawing
No. In Stock
SG200-BN2-00508 0.5 0.25 2 0.45 8 50 4 1 ○
SG200-BN2-01010 1 0.5 3 0.95 10 50 4 1 ●
SG200-BN2-01015 1 0.5 3 0.95 15 60 4 1 ●
SG200-BN2-01020 1 0.5 3 0.95 20 60 4 1 ●
SG200-BN2-01515 1.5 0.75 3 1.44 15 50 4 1 ●
SG200-BN2-02015 2 1 6 1.95 15 75 4 1 ●
SG200-BN2-02020 2 1 4 1.92 20 75 4 1 ●
SG200-BN2-02030 2 1 6 1.92 30 75 4 1 ●
SG200-BN2-03015 3 1.5 6 2.9 15 50 4 1 ●
SG200-BN2-03020 3 1.5 6 2.9 20 75 4 1 ●
SG200-BN2-04012 4 2 8 3.9 12 60 4 2 ●
SG200-BN2-04020 4 2 8 3.9 20 60 4 2 ●
2 Flutes, Ballnose, with Long Neck
SG200-BN2
Fig1
Fig2
●Stock ○Available Upon Order
Helix
U-DIA 30 ° 2 SHANK
h6
Unit (mm)
D Tolerance
R＜3 0
-0.02
3≤R≤6 0
-0.03
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
423
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Fig1
Fig2
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
○ ○ ◎
Order No. D R Lc d2 L1 L d Drawing
No. In Stock
SG200-BN2-06018 6 3 12 5.9 18 75 6 2 ○
SG200-BN2-06025 6 3 16 5.9 25 75 6 2 ○
SG200-BN2-06030 6 3 12 5.9 30 75 6 2 ●
SG200-BN2-08024 8 4 14 7.9 24 100 8 2 ○
SG200-BN2-08030 8 4 20 7.9 30 100 8 2 ○
SG200-BN2-08040 8 4 14 7.9 40 100 8 2 ○
SG200-BN2-10030 10 5 18 9.8 30 100 10 2 ●
SG200-BN2-10040 10 5 22 9.8 40 100 10 2 ○
SG200-BN2-10050 10 5 18 9.8 50 100 10 2 ○
SG200-BN2-12035 12 6 22 11.8 35 100 12 2 ○
SG200-BN2-12050 12 6 22 11.8 50 100 12 2 ○
2 Flutes, Ballnose, with Long Neck
SG200-BN2
●Stock ○Available Upon Order
Helix
U-DIA 30 ° 2 SHANK
h6
Unit (mm)
D Tolerance
R＜3 0
-0.02
3≤R≤6 0
-0.03
◎ Most Suitable ○ Suitable
Continued
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
Fig1
Fig2
424
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
◎
Order No. D Lc R d2 L1 L d Drawing
No. In Stock
SG200-M-RN4-1-6-0.1-50 1 2 0.1 0.96 6 50 4 1 ●
SG200-M-RN4-2-6-0.15-50 2 3.5 0.15 1.92 6 50 4 1 ●
SG200-M-RN4-2-12-0.15-50 2 3.5 0.15 1.92 12 50 4 1 ○
SG200-M-RN4-2-6-0.2-50 2 3.5 0.2 1.92 6 50 4 1 ●
SG200-M-RN4-2-12-0.2-50 2 3.5 0.2 1.92 12 50 4 1 ○
SG200-M-RN4-2-6-0.3-50 2 3.5 0.3 1.92 6 50 4 1 ●
SG200-M-RN4-2-12-0.3-50 2 3.5 0.3 1.92 12 50 4 1 ○
SG200-M-RN4-3-10-0.15-50 3 4 0.15 2.9 10 50 4 1 ●
SG200-M-RN4-3-10-0.2-50 3 4 0.2 2.9 10 50 4 1 ●
SG200-M-RN4-3-15-0.2-50 3 4 0.2 2.9 15 50 4 1 ○
SG200-M-RN4-3-10-0.5-50 3 4 0.5 2.9 10 50 4 1 ●
SG200-M-RN4-4-10-0.2-50 4 6 0.2 3.9 10 50 4 2 ●
SG200-M-RN4-4-15-0.5-50 4 6 0.5 3.9 15 50 4 2 ●
SG200-M-RN4-4-10-1-50 4 6 1 3.9 10 50 4 2 ●
SG200-M-RN4-6-25-0.5-50 6 9 0.5 5.9 25 50 6 2 ○
SG200-M-RN4-6-25-1-50 6 9 1 5.9 25 50 6 2 ○
SG200-M-RN4-6-20-1.5-50 6 15 1.5 5.9 20 50 6 2 ○
SG200-M-RN4-6-20-2-50 6 15 2 5.9 20 50 6 2 ○
SG200-M-RN4-8-30-1-60 8 10 1 7.9 30 60 8 2 ○
SG200-M-RN4-10-35-0.5-75 10 15 0.5 9.8 35 75 10 2 ●
SG200-M-RN4-10-45-1-75 10 15 1 9.8 45 75 10 2 ○
4 Flutes, Corner Radius, with Long Neck
SG200-M-RN4
●Stock ○Available Upon Order
Helix
Unit (mm)
D Tolerance
D≤4 0
-0.010
D＞4 0
-0.015
SHANK
h5
N-DIA Helix
40 °
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
Fig1
Fig2
425
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
◎
Order No. D R Lc L d Drawing No. In Stock
SG200-M-B2-0.4-1.5-50 0.4 0.2 1.5 50 4 1 ●
SG200-M-B2-0.5-2-50 0.5 0.25 2 50 4 1 ●
SG200-M-B2-0.6-2-50 0.6 0.3 2 50 4 1 ●
SG200-M-B2-0.8-3-50 0.8 0.4 3 50 4 1 ●
SG200-M-B2-1-3-50 1 0.5 3 50 4 1 ●
SG200-M-B2-1.5-5-50 1.5 0.75 5 50 4 1 ●
SG200-M-B2-2-6-50 2 1 6 50 4 1 ○
SG200-M-B2-3-8-50 3 1.5 8 50 4 1 ●
SG200-M-B2-4-16-50 4 2 16 50 4 2 ●
SG200-M-B2-5-16-50 5 2.5 16 50 6 1 ●
SG200-M-B2-6-16-50 6 3 16 50 6 2 ○
2 Flutes, Ballnose
SG200-M-B2
Fig1
Fig2
●Stock ○Available Upon Order
Helix
Unit (mm)
R Tolerance
R≤0.4 ±0.003
R＞0.4 ±0.005
SHANK
h5
N-DIA Helix
30 °
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
426
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Helix
Unit (mm)
R Tolerance
R≤0.4 ±0.003
R＞0.4 ±0.005
SHANK
h5
N-DIA Helix
30 °
Workpiece Material
1234 5 123 123 123 4 5
Carbon Steel/
Alloy Steel
(<35HRC)
Alloy Steel
(≤48HRC) Stainless Steel Cast Iron Aluminum Alloy Copper Alloy Graphite
◎
Order No. D R Lc d2 L1 L d Drawing
No. In Stock
SG200-M-BN2-0.5-8-50 0.5 0.25 2 0.46 8 50 4 1 ●
SG200-M-BN2-0.6-10-50 0.6 0.3 2 0.55 10 50 4 1 ○
SG200-M-BN2-0.8-15-50 0.8 0.4 3 0.75 15 50 4 1 ●
SG200-M-BN2-1-2.5-45 1 0.5 1.5 0.95 2.5 45 4 1 ●
SG200-M-BN2-1-7-50 1 0.5 3 0.95 7 50 4 1 ●
SG200-M-BN2-1-10-50 1 0.5 3 0.95 10 50 4 1 ●
SG200-M-BN2-1-15-50 1 0.5 3 0.95 15 50 4 1 ●
SG200-M-BN2-2-5-45 2 1 3 1.92 5 45 4 1 ●
SG200-M-BN2-2-8-50 2 1 3 1.95 8 50 4 1 ●
SG200-M-BN2-2-10-50 2 1 6 1.92 10 50 4 1 ●
SG200-M-BN2-3-15-50 3 1.5 8 2.90 15 50 4 1 ●
SG200-M-BN2-4-25-50 4 2 8 3.90 25 50 4 2 ●
SG200-M-BN2-6-25-50 6 3 16 5.90 25 50 6 2 ●
2 Flutes, Ballnose, with Long Neck
SG200-M-BN2
Fig1
Fig2
●Stock ○Available Upon Order
◎ Most Suitable ○ Suitable
Recommended Cutting Data ※ P662
Please refer to P201 for guidelines to icons
427
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Order No. D Lc L d Drawing No. In Stock
ST210-S4-01003 1 3 50 4 1 ○
ST210-S4-01504 1.5 4 50 4 1 ○
ST210-S4-02006 2 6 50 4 1 ●
ST210-S4-02506 2.5 6 50 4 1 ●
ST210-S4-02508 2.5 8 50 4 1 ●
ST210-S4-03009 3 9 50 4 1 ●
ST210-S4-03510 3.5 10 50 4 1 ●
ST210-S4-04011 4 11 50 4 2 ●
ST210-S4-04511 4.5 11 50 6 1 ○
ST210-S4-05013 5 13 50 6 1 ●
ST210-S4-06016 6 16 50 6 2 ●
ST210-S4-08020 8 20 60 8 2 ●
ST210-S4-10025 10 25 72 10 2 ●
ST210-S4-12030 12 30 75 12 2 ●
ST210-S4-14032 14 32 80 14 2 ●
ST210-S4-16036 16 36 100 16 2 ●
ST210-S4-20045 20 45 100 20 2 ●
4 Flutes, Square, with Unequal Tooth Pitch
ST210-S4
Unit (mm)
D Tolerance
D<6 0
-0.02
6≤D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
Square
SHANK
h6 4 AICrN
Fig1
Fig2
Recommended Cutting Data ※ P663
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Helix
38 /40
428
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Order No. D R Lc L d Drawing No. In Stock
ST210-R4-02002 2 0.2 6 50 4 1 ●
ST210-R4-03002 3 0.2 9 50 4 1 ○
ST210-R4-03003 3 0.3 9 50 4 1 ●
ST210-R4-03005 3 0.5 9 50 4 1 ●
ST210-R4-04003 4 0.3 11 50 4 2 ●
ST210-R4-04005 4 0.5 11 50 4 2 ●
ST210-R4-04010 4 1 11 50 4 2 ●
ST210-R4-05005 5 0.5 13 50 6 1 ●
ST210-R4-06005 6 0.5 16 50 6 2 ●
ST210-R4-06010 6 1 16 50 6 2 ●
ST210-R4-08005 8 0.5 20 60 8 2 ●
ST210-R4-08010 8 1 20 60 8 2 ●
ST210-R4-10002 10 0.2 25 72 10 2 ○
ST210-R4-10005 10 0.5 25 72 10 2 ●
ST210-R4-10010 10 1 25 72 10 2 ●
ST210-R4-10015 10 1.5 25 72 10 2 ○
ST210-R4-10020 10 2 25 72 10 2 ●
ST210-R4-10030 10 3 25 72 10 2 ●
ST210-R4-12005 12 0.5 30 75 12 2 ●
ST210-R4-12010 12 1 30 75 12 2 ●
4 Flutes, Corner Raidus, with Unequal Tooth Pitch
ST210-R4
Unit (mm)
D Tolerance
D<6 0
-0.02
6≤D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 4 AICrN Helix
38 /40
Fig1
Fig2
Recommended Cutting Data ※ P663
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
429
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Fig1
Fig2
Order No. D R Lc L d Drawing No. In Stock
ST210-R4-12020 12 2 30 75 12 2 ●
ST210-R4-12030 12 3 30 75 12 2 ●
ST210-R4-16005 16 0.5 36 100 16 2 ●
ST210-R4-16010 16 1 36 100 16 2 ●
ST210-R4-16020 16 2 36 100 16 2 ●
ST210-R4-16030 16 3 36 100 16 2 ●
ST210-R4-16040 16 4 36 100 16 2 ●
ST210-R4-16050 16 5 36 100 16 2 ●
ST210-R4-20005 20 0.5 45 100 20 2 ●
ST210-R4-20010 20 1 45 100 20 2 ●
ST210-R4-20020 20 2 45 100 20 2 ●
ST210-R4-20030 20 3 45 100 20 2 ●
ST210-R4-20040 20 4 45 100 20 2 ○
ST210-R4-20050 20 5 45 100 20 2 ○
4 Flutes, Corner Raidus, with Unequal Tooth Pitch
ST210-R4
Unit (mm)
D Tolerance
D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 4 AICrN Helix
38 /40
Recommended Cutting Data ※ P663
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Please refer to P201 for guidelines to icons
Continued
430
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
ST210-RN4-06005 6 0.5 12 18 5.4 60 6 1 ●
ST210-RN4-06010 6 1 12 18 5.4 60 6 1 ●
ST210-RN4-08005 8 0.5 16 25 7.4 75 8 1 ●
ST210-RN4-08010 8 1 16 25 7.4 75 8 1 ●
ST210-RN4-10005 10 0.5 20 30 9.4 75 10 1 ●
ST210-RN4-10005A 10 0.5 30 50 9.4 90 10 1 ●
ST210-RN4-10010 10 1 20 30 9.4 75 10 1 ●
ST210-RN4-10010A 10 1 30 50 9.4 90 10 1 ●
ST210-RN4-10020 10 2 20 30 9.4 75 10 1 ●
ST210-RN4-10020A 10 2 30 50 9.4 90 10 1 ●
ST210-RN4-10030 10 3 20 30 9.4 75 10 1 ●
ST210-RN4-10030A 10 3 30 50 9.4 90 10 1 ●
ST210-RN4-10030B 10 3 30 60 9.4 100 10 1 ●
ST210-RN4-10030C 10 3 30 40 9.4 90 10 1 ●
ST210-RN4-12005 12 0.5 24 40 11.4 90 12 1 ●
ST210-RN4-12005A 12 0.5 24 50 11.4 100 12 1 ●
ST210-RN4-12010 12 1 24 40 11.4 90 12 1 ●
ST210-RN4-12010A 12 1 24 50 11.4 100 12 1 ●
ST210-RN4-12020 12 2 24 40 11.4 90 12 1 ●
ST210-RN4-12020A 12 2 24 50 11.4 100 12 1 ●
4 Flutes, Corner Raidus, with Unequal Tooth Pitch and Long Neck
ST210-RN4
Unit (mm)
D Tolerance
D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 4 AICrN Helix
38 /40
Recommended Cutting Data ※ P663
◎ Most Suitable ○ Suitable
Fig1
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Please refer to P201 for guidelines to icons
431
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Fig1
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
ST210-RN4-12030A 12 3 24 40 11.4 90 12 1 ●
ST210-RN4-12030B 12 3 36 50 11.4 100 12 1 ●
ST210-RN4-12030C 12 3 36 60 11.4 110 12 1 ●
ST210-RN4-16005 16 0.5 32 50 15.4 100 16 1 ●
ST210-RN4-16005A 16 0.5 32 60 15.4 110 16 1 ●
ST210-RN4-16010 16 1 32 50 15.4 100 16 1 ●
ST210-RN4-16010A 16 1 32 70 15.4 120 16 1 ●
ST210-RN4-16010B 16 1 32 80 15.4 130 16 1 ○
ST210-RN4-16010C 16 1 32 60 15.4 110 16 1 ●
ST210-RN4-16020 16 2 32 50 15.4 100 16 1 ●
ST210-RN4-16020A 16 2 32 60 15.4 110 16 1 ●
ST210-RN4-16030 16 3 32 50 15.4 100 16 1 ●
ST210-RN4-16030A 16 3 32 70 15.4 120 16 1 ●
ST210-RN4-16030B 16 3 32 80 15.4 130 16 1 ●
ST210-RN4-16030C 16 3 32 60 15.4 110 16 1 ●
ST210-RN4-16040 16 4 32 50 15.4 100 16 1 ○
ST210-RN4-16040A 16 4 32 60 15.4 110 16 1 ○
ST210-RN4-16050 16 5 32 50 15.4 100 16 1 ●
ST210-RN4-16050A 16 5 32 60 15.4 110 16 1 ●
ST210-RN4-16050B 16 5 32 70 15.4 120 16 1 ○
4 Flutes, Corner Raidus, with Unequal Tooth Pitch and Long Neck
ST210-RN4
Unit (mm)
D Tolerance
D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 4 AICrN Helix
38 /40
Recommended Cutting Data ※ P663
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Please refer to P201 for guidelines to icons
Continued
432
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
Order No. D R Lc L1 d2 L d Drawing
No. In Stock
ST210-RN4-16050C 16 5 32 80 15.4 130 16 1 ●
ST210-RN4-20005 20 0.5 40 60 19.4 110 20 1 ●
ST210-RN4-20005A 20 0.5 40 80 19.4 130 20 1 ○
ST210-RN4-20010 20 1 40 60 19.4 110 20 1 ●
ST210-RN4-20010A 20 1 40 80 19.4 130 20 1 ○
ST210-RN4-20010B 20 1 40 70 19.4 120 20 1 ●
ST210-RN4-20010C 20 1 40 100 19.4 150 20 1 ●
ST210-RN4-20020 20 2 40 60 19.4 110 20 1 ●
ST210-RN4-20020A 20 2 40 80 19.4 130 20 1 ●
ST210-RN4-20030 20 3 40 60 19.4 110 20 1 ●
ST210-RN4-20030A 20 3 40 80 19.4 130 20 1 ●
ST210-RN4-20030B 20 3 40 100 19.4 150 20 1 ●
ST210-RN4-20030C 20 3 40 70 19.4 120 20 1 ●
ST210-RN4-20040 20 4 40 60 19.4 110 20 1 ●
ST210-RN4-20040A 20 4 40 80 19.4 130 20 1 ●
ST210-RN4-20050 20 5 40 60 19.4 110 20 1 ●
ST210-RN4-20050A 20 5 40 80 19.4 130 20 1 ○
ST210-RN4-20050B 20 5 40 100 19.4 150 20 1 ○
ST210-RN4-20050C 20 5 40 70 19.4 120 20 1 ●
4 Flutes, Corner Raidus, with Unequal Tooth Pitch and Long Neck
ST210-RN4
Unit (mm)
D Tolerance
D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 4 AICrN Helix
38 /40
Recommended Cutting Data ※ P663
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Please refer to P201 for guidelines to icons
Fig1
Continued
433
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
Order No. D R Lc L d Drawing No. In Stock
ST210-RL5-16005 16 0.5 48 100 16 1 ●
ST210-RL5-16005A 16 0.5 80 130 16 1 ●
ST210-RL5-20005 20 0.5 60 110 20 1 ●
ST210-RL5-20005A 20 0.5 100 150 20 1 ●
ST210-RL5-25005 25 0.5 75 155 25 1 ○
ST210-RL5-25005A 25 0.5 125 205 25 1 ●
5 Flutes, Corner Raidus, with Unequal Tooth Pitch and Long Flute
ST210-RL5
Unit (mm)
D Tolerance
D≤16 0
-0.03
D>16 0
-0.04
●Stock ○Available Upon Order
SHANK
h6 Helix
45
Fig1
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Recommended Cutting Data ※ P663
Please refer to P201 for guidelines to icons
AICrSiN
434
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
R Tolerance
R<3 ±0.010
3≤R≤6 ±0.015
R<6 ±0.020
Unit (mm)
Fig1
Fig2
4 Flutes, Ballnose, with Unequal Tooth Pitch
ST210-B4
●Stock ○Available Upon Order
SHANK
h6 4 Helix
30
Order No. D R Lc L d Drawing No. In Stock
ST210-B4-02004 2 1 4 50 6 1 ●
ST210-B4-03006 3 1.5 6 50 6 1 ●
ST210-B4-04008 4 2 8 50 6 1 ●
ST210-B4-05010 5 2.5 10 50 6 1 ●
ST210-B4-06012 6 3 12 50 6 2 ●
ST210-B4-08014 8 4 14 60 8 2 ●
ST210-B4-10018 10 5 18 75 10 2 ●
ST210-B4-12022 12 6 22 75 12 2 ●
ST210-B4-16030 16 8 30 100 16 2 ●
ST210-B4-20038 20 10 38 100 20 2 ●
◎ Most Suitable ○ Suitable
Ballnose
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
○ ○ ◎ ○ ◎
Recommended Cutting Data ※ P663
Please refer to P201 for guidelines to icons
AICrSiN
435
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Standard Length, Square
ST300-S4
Fig1
Fig2
Square
Order No. D C Lc L d Drawing No. In Stock
ST300-S4-01003 1 - 3 50 4 1 ●
ST300-S4-01504 1.5 - 4 50 4 1 ●
ST300-S4-02006 2 0.02 6 50 4 1 ●
ST300-S4-02506 2.5 0.02 6 50 4 1 ●
ST300-S4-03009 3 0.03 9 50 4 1 ●
ST300-S4-03510 3.5 0.03 10 50 4 1 ○
ST300-S4-04011 4 0.04 11 50 4 2 ●
ST300-S4-04511 4.5 0.04 11 50 6 1 ○
ST300-S4-05013 5 0.05 13 50 6 1 ●
ST300-S4-06016 6 0.06 16 50 6 2 ●
ST300-S4-08020 8 0.08 20 60 8 2 ●
ST300-S4-10025 10 0.10 25 75 10 2 ●
ST300-S4-12030 12 0.10 30 75 12 2 ●
ST300-S4-14032 14 0.10 32 80 14 2 ○
ST300-S4-16036 16 0.10 36 100 16 2 ●
ST300-S4-20045 20 0.10 45 100 20 2 ●
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
436
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius
ST300-R4
Fig1
Fig2
Order No. D R Lc L d Drawing No. In Stock
ST300-R4-02002 2 0.2 6 50 4 1 ●
ST300-R4-03003 3 0.3 9 50 4 1 ●
ST300-R4-03005 3 0.5 9 50 4 1 ●
ST300-R4-04003 4 0.3 11 50 4 2 ●
ST300-R4-04005 4 0.5 11 50 4 2 ●
ST300-R4-04010 4 1 11 50 4 2 ●
ST300-R4-05005 5 0.5 13 50 6 1 ●
ST300-R4-06005 6 0.5 16 50 6 2 ●
ST300-R4-06010 6 1 16 50 6 2 ●
ST300-R4-08002 8 0.2 20 60 8 2 ●
ST300-R4-08005 8 0.5 20 60 8 2 ●
ST300-R4-08010 8 1 20 60 8 2 ●
ST300-R4-10002 10 0.2 25 75 10 2 ○
ST300-R4-10005 10 0.5 25 75 10 2 ●
ST300-R4-10010 10 1 25 75 10 2 ●
ST300-R4-10020 10 2 25 75 10 2 ●
ST300-R4-10030 10 3 25 75 10 2 ●
ST300-R4-12002 12 0.2 30 75 12 2 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
437
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius
ST300-R4
Fig1
Fig2
Order No. D R Lc L d Drawing No. In Stock
ST300-R4-12005 12 0.5 30 75 12 2 ●
ST300-R4-12010 12 1 30 75 12 2 ●
ST300-R4-12020 12 2 30 75 12 2 ●
ST300-R4-12030 12 3 30 75 12 2 ●
ST300-R4-16002 16 0.2 36 100 16 2 ○
ST300-R4-16005 16 0.5 36 100 16 2 ●
ST300-R4-16010 16 1 36 100 16 2 ●
ST300-R4-16020 16 2 36 100 16 2 ●
ST300-R4-16030 16 3 36 100 16 2 ●
ST300-R4-16040 16 4 36 100 16 2 ●
ST300-R4-16050 16 5 36 100 16 2 ●
ST300-R4-20002 20 0.2 45 100 20 2 ○
ST300-R4-20005 20 0.5 45 100 20 2 ●
ST300-R4-20010 20 1 45 100 20 2 ●
ST300-R4-20020 20 2 45 100 20 2 ●
ST300-R4-20030 20 3 45 100 20 2 ●
ST300-R4-20040 20 4 45 100 20 2 ○
ST300-R4-20050 20 5 45 100 20 2 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
438
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
4 Flutes, Corner Radius, with Long Shank Length
ST300-RH4
Fig1
Fig2
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
Order No. D R Lc L d Drawing No. In Stock
ST300-RH4-06005 6 0.5 16 75 6 2 ●
ST300-RH4-06010 6 1 16 75 6 2 ●
ST300-RH4-08002 8 0.2 20 75 8 2 ●
ST300-RH4-08005 8 0.5 20 75 8 2 ●
ST300-RH4-08010 8 1 20 75 8 2 ●
ST300-RH4-10002 10 0.2 30 100 10 2 ○
ST300-RH4-10005 10 0.5 30 100 10 2 ●
ST300-RH4-10010 10 1 30 100 10 2 ●
ST300-RH4-10020 10 2 30 100 10 2 ●
ST300-RH4-10030 10 3 30 100 10 2 ●
ST300-RH4-12002A 12 0.2 30 100 12 2 ○
ST300-RH4-12002B 12 0.2 30 120 12 2 ○
ST300-RH4-12005A 12 0.5 30 100 12 2 ○
ST300-RH4-12005B 12 0.5 30 120 12 2 ●
ST300-RH4-12010A 12 1 30 100 12 2 ○
ST300-RH4-12010B 12 1 30 120 12 2 ●
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
439
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Shank Length
ST300-RH4
Fig1
Fig2
Order No. D R Lc L d Drawing No. In Stock
ST300-RH4-12020A 12 2 30 100 12 2 ○
ST300-RH4-12020B 12 2 30 120 12 2 ●
ST300-RH4-12030A 12 3 30 100 12 2 ○
ST300-RH4-12030B 12 3 30 120 12 2 ●
ST300-RH4-16002A 16 0.2 40 150 16 2 ○
ST300-RH4-16002B 16 0.2 50 200 16 2 ○
ST300-RH4-16005A 16 0.5 40 150 16 2 ●
ST300-RH4-16005B 16 0.5 50 200 16 2 ○
ST300-RH4-16010A 16 1 40 150 16 2 ●
ST300-RH4-16010B 16 1 50 200 16 2 ○
ST300-RH4-16020A 16 2 40 150 16 2 ●
ST300-RH4-16020B 16 2 50 200 16 2 ○
ST300-RH4-16030A 16 3 40 150 16 2 ●
ST300-RH4-16030B 16 3 50 200 16 2 ○
ST300-RH4-16040A 16 4 40 150 16 2 ○
ST300-RH4-16040B 16 4 50 200 16 2 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
440
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Shank Length
ST300-RH4
Fig1
Fig2
Order No. D R Lc L d Drawing No. In Stock
ST300-RH4-16050A 16 5 40 150 16 2 ○
ST300-RH4-16050B 16 5 50 200 16 2 ○
ST300-RH4-20002A 20 0.2 50 150 20 2 ○
ST300-RH4-20002B 20 0.2 50 200 20 2 ○
ST300-RH4-20005A 20 0.5 50 150 20 2 ●
ST300-RH4-20005B 20 0.5 50 200 20 2 ○
ST300-RH4-20010A 20 1 50 150 20 2 ●
ST300-RH4-20010B 20 1 50 200 20 2 ○
ST300-RH4-20020A 20 2 50 150 20 2 ●
ST300-RH4-20020B 20 2 50 200 20 2 ○
ST300-RH4-20030A 20 3 50 150 20 2 ●
ST300-RH4-20030B 20 3 50 200 20 2 ○
ST300-RH4-20040A 20 4 50 150 20 2 ○
ST300-RH4-20040B 20 4 50 200 20 2 ○
ST300-RH4-20050A 20 5 50 150 20 2 ○
ST300-RH4-20050B 20 5 50 200 20 2 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
441
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Neck
ST300-RN4
Fig1
Order No. D R Lc L1 d2 L d Drawing No. In Stock
ST300-RN4-06005 6 0.5 12 18 5.4 60 6 1 ○
ST300-RN4-06010 6 1 12 18 5.4 60 6 1 ○
ST300-RN4-08005 8 0.5 16 25 7.4 75 8 1 ●
ST300-RN4-08010 8 1 16 25 7.4 75 8 1 ●
ST300-RN4-10005A 10 0.5 20 30 9.4 75 10 1 ○
ST300-RN4-10005B 10 0.5 30 50 9.4 90 10 1 ○
ST300-RN4-10010A 10 1 20 30 9.4 75 10 1 ○
ST300-RN4-10010B 10 1 30 50 9.4 90 10 1 ○
ST300-RN4-10020A 10 2 20 30 9.4 75 10 1 ○
ST300-RN4-10020B 10 2 30 50 9.4 90 10 1 ○
ST300-RN4-10030A 10 3 20 30 9.4 75 10 1 ●
ST300-RN4-10030B 10 3 30 40 9.4 90 10 1 ●
ST300-RN4-10030C 10 3 30 50 9.4 90 10 1 ●
ST300-RN4-10030D 10 3 30 60 9.4 100 10 1 ●
ST300-RN4-12005A 12 0.5 24 40 11.4 90 12 1 ○
ST300-RN4-12005B 12 0.5 24 50 11.4 100 12 1 ○
ST300-RN4-12010A 12 1 24 40 11.4 90 12 1 ○
ST300-RN4-12010B 12 1 24 50 11.4 100 12 1 ○
ST300-RN4-12010C 12 1 36 60 11.4 110 12 1 ○
ST300-RN4-12020A 12 2 24 40 11.4 90 12 1 ○
ST300-RN4-12020B 12 2 24 50 11.4 100 12 1 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
442
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Neck
ST300-RN4
Fig1
Order No. D R Lc L1 d2 L d Drawing No. In Stock
ST300-RN4-12030A 12 3 24 40 11.4 90 12 1 ●
ST300-RN4-12030B 12 3 36 50 11.4 100 12 1 ●
ST300-RN4-12030C 12 3 36 60 11.4 110 12 1 ●
ST300-RN4-16005A 16 0.5 32 50 15.4 100 16 1 ○
ST300-RN4-16005B 16 0.5 32 60 15.4 110 16 1 ○
ST300-RN4-16005C 16 0.5 32 70 15.4 120 16 1 ○
ST300-RN4-16005D 16 0.5 32 80 15.4 130 16 1 ○
ST300-RN4-16010A 16 1 32 50 15.4 100 16 1 ○
ST300-RN4-16010B 16 1 32 60 15.4 110 16 1 ○
ST300-RN4-16010C 16 1 32 70 15.4 120 16 1 ○
ST300-RN4-16010D 16 1 32 80 15.4 130 16 1 ○
ST300-RN4-16020A 16 2 32 50 15.4 100 16 1 ○
ST300-RN4-16020B 16 2 32 60 15.4 110 16 1 ○
ST300-RN4-16030A 16 3 32 50 15.4 100 16 1 ●
ST300-RN4-16030B 16 3 32 60 15.4 110 16 1 ●
ST300-RN4-16030C 16 3 32 70 15.4 120 16 1 ●
ST300-RN4-16030D 16 3 32 80 15.4 130 16 1 ●
ST300-RN4-16040A 16 4 32 50 15.4 100 16 1 ○
ST300-RN4-16040B 16 4 32 60 15.4 110 16 1 ○
ST300-RN4-16040C 16 4 32 70 15.4 120 16 1 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
443
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Neck
ST300-RN4
Fig1
Order No. D R Lc L1 d2 L d Drawing No. In Stock
ST300-RN4-16040D 16 4 32 80 15.4 130 16 1 ○
ST300-RN4-16050A 16 5 32 50 15.4 100 16 1 ○
ST300-RN4-16050B 16 5 32 60 15.4 110 16 1 ○
ST300-RN4-16050C 16 5 32 70 15.4 120 16 1 ○
ST300-RN4-16050D 16 5 32 80 15.4 130 16 1 ○
ST300-RN4-20005A 20 0.5 40 60 19.4 110 20 1 ○
ST300-RN4-20005B 20 0.5 40 70 19.4 120 20 1 ○
ST300-RN4-20005C 20 0.5 40 80 19.4 130 20 1 ○
ST300-RN4-20005D 20 0.5 40 100 19.4 150 20 1 ○
ST300-RN4-20010A 20 1 40 60 19.4 110 20 1 ○
ST300-RN4-20010B 20 1 40 70 19.4 120 20 1 ○
ST300-RN4-20010C 20 1 40 80 19.4 130 20 1 ○
ST300-RN4-20010D 20 1 40 100 19.4 150 20 1 ○
ST300-RN4-20020A 20 2 40 60 19.4 110 20 1 ○
ST300-RN4-20020B 20 2 40 80 19.4 130 20 1 ○
ST300-RN4-20030A 20 3 40 60 19.4 110 20 1 ●
ST300-RN4-20030B 20 3 40 70 19.4 120 20 1 ●
ST300-RN4-20030C 20 3 40 80 19.4 130 20 1 ●
ST300-RN4-20030D 20 3 40 100 19.4 150 20 1 ●
ST300-RN4-20040A 20 4 40 60 19.4 110 20 1 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
444
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
4 Flutes, Corner Radius, with Long Neck
ST300-RN4
Fig1
Order No. D R Lc L1 d2 L d Drawing No. In Stock
ST300-RN4-20040B 20 4 40 70 19.4 120 20 1 ○
ST300-RN4-20040C 20 4 40 80 19.4 130 20 1 ○
ST300-RN4-20040D 20 4 40 100 19.4 150 20 1 ○
ST300-RN4-20050A 20 5 40 60 19.4 110 20 1 ○
ST300-RN4-20050B 20 5 40 70 19.4 120 20 1 ○
ST300-RN4-20050C 20 5 40 80 19.4 130 20 1 ○
ST300-RN4-20050D 20 5 40 100 19.4 150 20 1 ○
ST300-RN4-25005 25 0.5 50 80 24.4 140 25 1 ○
ST300-RN4-25010A 25 1 50 80 24.4 140 25 1 ○
ST300-RN4-25010B 25 1 50 100 24.4 160 25 1 ○
ST300-RN4-25020 25 2 50 80 24.4 140 25 1 ○
ST300-RN4-25030A 25 3 50 80 24.4 140 25 1 ○
ST300-RN4-25030B 25 3 50 100 24.4 160 25 1 ○
ST300-RN4-25030C 25 3 50 120 24.4 180 25 1 ○
ST300-RN4-25040 25 4 50 80 24.4 140 25 1 ○
ST300-RN4-25050A 25 5 50 80 24.4 140 25 1 ○
ST300-RN4-25050B 25 5 50 100 24.4 160 25 1 ○
●Stock ○Available Upon Order
4 GSR7115 SHANK
h6 Helix
40 /42
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
445
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
5 Flutes, Corner Radius
ST300-R5
Fig1
Order No. D C Lc L d Drawing No. In Stock
ST300-R5-06002 6 0.2 16 50 6 1 ●
ST300-R5-06005 6 0.5 16 50 6 1 ●
ST300-R5-06010 6 1 16 50 6 1 ●
ST300-R5-08002 8 0.2 20 60 8 1 ●
ST300-R5-08005 8 0.5 20 60 8 1 ●
ST300-R5-08010 8 1 20 60 8 1 ●
ST300-R5-10002 10 0.2 25 75 10 1 ○
ST300-R5-10005 10 0.5 25 75 10 1 ●
ST300-R5-10010 10 1 25 75 10 1 ●
ST300-R5-10020 10 2 25 75 10 1 ●
ST300-R5-10030 10 3 25 75 10 1 ●
ST300-R5-12002 12 0.2 30 75 12 1 ○
ST300-R5-12005 12 0.5 30 75 12 1 ●
ST300-R5-12010 12 1 30 75 12 1 ●
ST300-R5-12020 12 2 30 75 12 1 ●
●Stock ○Available Upon Order
GSR7115 SHANK
h6
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Helix
42 °
446
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
5 Flutes, Corner Radius
ST300-R5
Fig1
Order No. D C Lc L d Drawing No. In Stock
ST300-R5-12030 12 3 30 75 12 1 ●
ST300-R5-16002 16 0.2 36 100 16 1 ○
ST300-R5-16005 16 0.5 36 100 16 1 ●
ST300-R5-16010 16 1 36 100 16 1 ●
ST300-R5-16020 16 2 36 100 16 1 ●
ST300-R5-16030 16 3 36 100 16 1 ●
ST300-R5-16040 16 4 36 100 16 1 ○
ST300-R5-16050 16 5 36 100 16 1 ○
ST300-R5-20002 20 0.2 45 100 20 1 ○
ST300-R5-20005 20 0.5 45 100 20 1 ●
ST300-R5-20010 20 1 45 100 20 1 ●
ST300-R5-20020 20 2 45 100 20 1 ●
ST300-R5-20030 20 3 45 100 20 1 ●
ST300-R5-20040 20 4 45 100 20 1 ○
ST300-R5-20050 20 5 45 100 20 1 ○
●Stock ○Available Upon Order
GSR7115 SHANK
h6
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
Helix
42 °
447
Solid Carbide Endmills
B
Solid Carbide Endmills MILLING
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
5 Flutes, Corner Radius, with Long Shank Length
ST300-RH5
Fig1
Order No. D C Lc L d Drawing No. In Stock
ST300-RH5-06002 6 0.2 16 75 6 1 ●
ST300-RH5-06005 6 0.5 16 75 6 1 ●
ST300-RH5-06010 6 1 16 75 6 1 ●
ST300-RH5-08002 8 0.2 20 75 8 1 ●
ST300-RH5-08005 8 0.5 20 75 8 1 ●
ST300-RH5-08010 8 1 20 75 8 1 ●
ST300-RH5-10002 10 0.2 30 100 10 1 ○
ST300-RH5-10005 10 0.5 30 100 10 1 ●
ST300-RH5-10010 10 1 30 100 10 1 ●
ST300-RH5-10020 10 2 30 100 10 1 ●
ST300-RH5-10030 10 3 30 100 10 1 ●
ST300-RH5-12002A 12 0.2 30 100 12 1 ○
ST300-RH5-12002B 12 0.2 30 120 12 1 ○
ST300-RH5-12005A 12 0.5 30 100 12 1 ○
ST300-RH5-12005B 12 0.5 30 120 12 1 ●
ST300-RH5-12010A 12 1 30 100 12 1 ○
●Stock ○Available Upon Order
GSR7115 SHANK
h6
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Helix
42 °
448
Solid Carbide Endmills
B
MILLING Solid Carbide Endmills
D Tolerance
D＜6 0
-0.02
6≤D≤12 0
-0.03
D>12 0
-0.04
Unit (mm)
5 Flutes, Corner Radius, with Long Shank Length
ST300-RH5
Fig1
Order No. D C Lc L d Drawing No. In Stock
ST300-RH5-12010B 12 1 30 120 12 1 ●
ST300-RH5-12020A 12 2 30 100 12 1 ○
ST300-RH5-12020B 12 2 30 120 12 1 ●
ST300-RH5-12030A 12 3 30 100 12 1 ○
ST300-RH5-12030B 12 3 30 120 12 1 ●
ST300-RH5-16002A 16 0.2 40 150 16 1 ○
ST300-RH5-16002B 16 0.2 50 200 16 1 ○
ST300-RH5-16005A 16 0.5 40 150 16 1 ●
ST300-RH5-16005B 16 0.5 50 200 16 1 ○
ST300-RH5-16010A 16 1 40 150 16 1 ●
ST300-RH5-16010B 16 1 50 200 16 1 ○
ST300-RH5-16020A 16 2 40 150 16 1 ●
ST300-RH5-16020B 16 2 50 200 16 1 ○
ST300-RH5-16030A 16 3 40 150 16 1 ●
ST300-RH5-16030B 16 3 50 200 16 1 ○
●Stock ○Available Upon Order
GSR7115 SHANK
h6
Please refer to P201 for guidelines to icons
◎ Most Suitable ○ Suitable
Workpiece Material
1 2 3 4 5 1 2 3 1 2 3 4
Carbon Steel/Alloy
Steel (<35HRC) Alloy Steel (≤48HRC) Stainless Steel High-temperature
Alloy Titanium Alloy
◎
Recommended Cutting Data ※ P664
Continued
Helix
42 °
