F3099 硅胶键盘 Silicone keyboard

产品手册 User manual

●时尚的外观设计。

•键帽经久耐磨，不易掉色，多色可选

·键盘按键反应灵敏，手感更好，经久耐用。

•具有智能休眠模式：主机进入休眠或待机状态，背光功能关闭，主机启动后恢复此前模式。

·键帽和缝隙背光，色彩均匀。

·键盘高效化设计，与Fn配合增加一系列常用快捷功能按键。

① 短按FN+\~进入
2.4G无线模式

①短按Fn+4进入有线模式

②将标配USB线缆Type-C一端插进键盘对应端口

③将线缆USB头一端插入电脑USB端口即可

开关机说明

•电池开关键为拔动开关，左右拨动对键盘的锂电进行开关控制，置左为关闭，置右为开启。

2.4G连接使用说明

②从键盘底部槽位内取出【USB接收器】
③插至电脑USB端口即可使用

组合键快速2.4G对码

•手动对码：短按组合键“FN+、\~”进入2.4G模式，已对码回连=Num指示灯慢闪状态，长按对码=FN+、\~Num指示灯对码时快闪，接收器插入电脑USB端口，99 Num“指示灯亮，2.4G连接成功。此时即完成对码。

① 短按FN+1/2/3进入蓝牙通道

②按组合键切换至BT1， 长按约3S至CAP灯快闪 进入配对

③在设备上搜索蓝牙设备【AULA-F3099】并连接

组合键快速切换设备：

短按
设备1

设备2

设备3

●长按3s组合键Fn+数字1！、2@或3#，CAP指示灯快闪，表示键盘进入对码或搜索模式，即可在设备中进行配对连接：回连状态下，为对应灯慢闪。

注：配对1分钟未成功进入休眠，回连20S未成功进入休眠。电源、CAP、NUM指示灯基础颜色为蓝色。

背光灯效调节

· 灯光操作方式(驱动支持音乐律动)

FN+PGUP依次切换灯效：

•系统切换及指示：(系统切换是电源指示灯红光闪烁)

快捷键说明

Windows系统快捷键(默认系统，左右ALT紧挨空格键)

Android系统快捷键(左右ALT紧挨空格键)

智能休眠模式说明

●超过2 mins 键盘未使用，进入一级休眠，灯光全关，按键唤醒；10mins键盘未使用，进入二级休眠，灯光全关，按键唤醒。

•电量指示：充电时，电池指示灯常亮，发（蓝光），充满后熄灭。

• 电量低于3.4V，关闭背光灯，电池指示灯发（红光）快闪直到休眠或关机。

• 有线时电池指示灯常亮（蓝光）。

• 电量低于 3.1V 关机。

• Type-C连接性更可靠，性能更稳定。

1、建议仅使用电脑USB接口对键盘进行充电；

2、请勿使用快充手机充电器对键盘充电；

3、请勿使用劣质非标电源适配器对键盘进行充电；

4、请勿使用过压过流电源适配器对键盘进行充电；

5、充电时请远离高温设备；

6、长时间不使用时请关闭电源开关。

以上充电说明同样适用于其他带充电功能设备(键盘/鼠标/耳机/音箱等)

双模式切换

游戏模式

M1-M3可以直接进行硬件定义

●M1 定义：FN+INS：三个指示灯慢闪进入录制状态，单按M1，三个指示灯（蓝光）快闪，进入M1的录制，录制完成，FN+INS保存录制功能即可。

•M2 定义：FN+INS：三个指示灯（蓝光）慢闪进入录制状态，单按M2，三个指示灯快闪，进入M2的录制，录制完成,FN+INS保存录制功能即可。

•M3 定义：FN+INS：三个指示灯慢闪进入录制状态，单按M3，三个指示灯（蓝光）快闪，进入M3的录制，录制完成,FN+INS保存录制功能即可。

注：无线连接下，M1/2/3自定义只能播，不能录，

FN+ESC 长按（3S）恢复出厂设置清除掉录制的内容。

旋钮开关切换灯效 扭动旋钮顺时针旋转(灯光亮度加) 扭动旋钮逆时针旋转(灯光亮度减)

注：亮度调节到最亮是NUM+CAP指示灯蓝光闪烁

办公模式

· M1键=上一曲

·M2键=播放/暂停

· M3键=下一曲

旋钮开关（向下按）=静音 顺时针扭动旋钮=音量减 逆时针扭动旋钮=音量加

· 键数：99键

• 按键总行程：4.0mm

• FN键多功能

·产品尺寸：412.39×158.02×51.69±0.2mm.

• 产品重量：约750g

• 充电电压/电流：DC 5V⎓450mA

• 额定电压：DC 3.7V（充满4.2V)

• 额定电流：<150mA

• 电池容量：2000mAh

• 充电接口：Type-C接口

• 电脑系统需求:

Windows ALL操作系统WIN XP, WIN7,WIN8,WIN10(在Win95，Win98系统下，可能需要驱动程序)。

配置有USB1.1或以上版本端口;

有至少20MB的硬盘空间.

2.4G或蓝牙可连接MAC、Android、IOS等移动设备，2.4G状态下需使用配对的接收器，键盘蓝牙版本为蓝牙5.2，适用蓝牙5.2及以下版本

· 硬件连接

硬件连接：USB支持热插拔（即插即用）。

注:win7及以下系统不支持蓝牙连接

尊敬的用户：

感谢您购买狼蛛系列产品！本质保卡是狼蛛产品的三包凭证，由用户自己保存，凭此质保卡您将享受狼蛛为您提供的产品售后服务。此质保卡每个产品一份，遗失不补，敬请妥善保管。

一、凭此卡您将享受以下权利与服务：

1、退货服务：自产品售出之日起七日内，产品出现质量问题，根据国家三包服务“的规定，在产品外观与包装完整的情况下，将产品退还给销售商或者狼蛛指定地点，凭购买时的有效凭证，退回您支付的产品货款。

2、保修服务：自购买日起12月内出现产品性能故障情况经由狼蛛售后服务中心检测确定，可免费享受维修服务。

二、以下情况不属于免费服务范围：

1、超出规定的质保期限；

2、不能出示产品有效质保凭证或产品原序列号标签有涂改、替换、撕毁等现象的；

3、产品上没有序列号或质保凭证上的产品型号与产品实物不符的；

4、非正常使用、维护、保管所导致的故障和损坏；

5、非我公司授权的维修人员对产品修理、更改或拆卸而造成的故障或损坏；

6、意外事故或其他不可抗力造成的故障或损坏；

7、销售人员承诺的产品之外的服务及附加的配件或赠品不在本保修服务范围之列;

8、因电源、电压不稳而导致的故障或损坏。

维修记录：

销售记录：

• Fashionable exterior design.

• The keycap is durable and resistant to fading, with multiple colors available.

• The keyboard buttons have a sensitive response, better hand feel, and are durable.

• Equipped with intelligent sleep mode: the host enters sleep or standby mode, the backlight function is turned off, and the host resumes the previous mode after startup.

• Key cap and gap backlight, with uniform color.

• High-Efficiency Keyboard Design, combined with Fn to add a series of commonly used shortcut function keys.

Power on/off instructions

• The key to turning on the battery is to pull the switch. Turning it left and right controls the lithium battery on and off of the keyboard. Setting it to the left means it is off, and setting it to the right means it is on.

2.4G Connection Instructions

Quick 2.4G code pairing with combination keys

• Manual code pairing: Short press the combination key "FN+\~" to enter 2.4G mode. After pairing, the Num indicator light will flash slowly. Long press the pairing=FN+ Num indicator light. When pairing, it will flash quickly. The receiver is inserted into the computer's USB port, and the "Num" indicator light will light up. The 2.4G connection is successful. At this point, the pairing is completed.

① Short press FN+1/2/3 to switch to BT mode.

②Press the combination key to switch to BT1, hold down for about 3 seconds until the CAP light flashes quickly to enter pairing

③Search for the BT device 【AULA-3099】on your device and connect

Quick device switching with combination keys:

Short press

Device 1

Device 2

Device 3

• Long press and hold the Fn+numbers 1! , 2@, or 3# for 3 seconds, and the CAP indicator light will flash quickly, indicating that the keyboard has entered pairing or search mode, and can be paired and connected in the device. In the reconnection state, the corresponding light will flash slowly.

Note: Pairing for 1 minute did not successfully enter sleep, and reconnecting for 20 seconds did not successfully enter sleep. The basic color of the power, CAP, and NUM indicator lights is blue.

Backlight Effect Adjustment

• Lighting operation mode (Driver supports music rhythm)

	END	Adjusting Light Colors (In constant light mode)
	PGUP	Adjust the next light effect
	PGDN	Adjust the last
		light effect

• System switching and indication: (The power indicator light flashes red during system switching)

Shortcut Key Description

Windows system shortcut key (default system, left and right ALT next to spacebar)

Note: The multimedia character icon on the keyboard is the default system function for Windows

Android System shortcut keys (left and right ALT next to spacebar)

Intelligent Sleep Mode Description

• If the keyboard is not used for more than 2 minutes, enter first level sleep mode, turn off all lights, and wake up with a button; The 10mins keyboard is not in use and enters second level sleep mode. The lights are all turned off and the button wakes up.

• Battery indicator: When charging, the battery indicator light remains on, emitting a blue light, and then goes off when fully charged.

• When the battery level is below 3.4V, turn off the backlight and the battery indicator light will flash rapidly (red light) until it goes to sleep or shuts down.

• When wired, the battery indicator light remains on (blue light).

• Power off when the battery level is below 3.1V.

• Type-C connectivity is more reliable and performance is more stable.

1. It is recommended to use only the computer USB port to charge the keyboard.

2. Do not use fast-charging cell phone chargers to charge the keyboard.

3. Do not use inferior non-standard power adapter to charge the keyboard.

4.Do not use over-voltage and over-current power adapter to charge the keyboard.

5.Please keep away from high temperature equipment when charging
6. Please turn off the power switch if it is not used for a long time.

The above charging instructions also apply to other devices with charging function (keyboard/mouse/headphones/speakers, etc.)

Dual mode switching

Game Mode

M1-M3 can directly define hardware

• M1 definition: FN+INS: Three indicator lights flash slowly to enter recording mode. Simply press M1, and the three indicator lights (blue light) flash quickly to enter M1 recording. After recording is completed, FN+INS saves the recording function.

• M2 definition: FN+INS: Three indicator lights (blue light) flash slowly to enter recording mode. Simply press M2, the three indicator lights flash quickly to enter M2 recording. After recording is completed, FN+INS saves the recording function.

• M3 definition: FN+INS: Three indicator lights flash slowly to enter recording mode. Simply press M3 and the three indicator lights (blue light) flash quickly to enter M3recording. After recording is completed, FN+INS saves the recording function.

Note: (In wireless connection mode, M1/2/3 only supports output anddoes not support recording.)

Press and hold FN+ESC for 3 seconds to restore factory settings and clear recorded content.

Knob switch switching light effect

Turn the knob clockwise to increase the brightness of the light Turn the knob counterclockwise (the brightness of the light decreases)

Note: When the brightness is adjusted to the brightest, the NUM+CAP indicator light flashes blue

Office Mode

• M1 key=Previous track

• M2 key=play/pause

• M3 key=next track

Knob switch (press down)=mute

Turning the knob clockwise=volume decrease

Turning the knob counterclockwise=volume increase

• Number of keys: 99

• Total travel of buttons: 4.0mm

• FN key multifunctional

• Product size: 4 1 2 . 3 9 x 1 5 8 . 0 2 x 5 1 . 6 9 ± 0 . 2 \mathsf {mm }

• Product weight: approximately 750g

• Charging voltage/current: DC 5V450mA

• Rated voltage: DC 3.7V (fully charged with 4.2V)

• Rated current:<150mA

• Battery capacity: 2000mAh

• Charging interface: Type-C interface

• Computer system requirements:

Windows ALL operating system WIN XP, WIN7, WIN8, WIN10 (under Win95, Win98 systems, drivers may be required).

Equipped with USB 1.1 or higher ports.

There is at least 20MB of hard disk space.

2.4G or Bluetooth can connect to mobile devices such as MAC, Android, IOS, etc. In 2.4G mode, a paired receiver is required. The keyboard Bluetooth version is Bluetooth 5.2, which is suitable for Bluetooth 5.2 and below

• Hardware connection

Hardware connection: USB supports hot swapping (plug and play).

Note: Win7 and below systems do not support Bluetooth connection

Dear Customer:

Thank you for purchasing AULA series products! This warranty card is the proof of AULA products, which is kept by the user, with this warranty card you will enjoy the after-sales service provided by AULA. This warranty card is a copy of each product and will not be replaced if lost, so please keep it in a safe place.

I. With this card you will enjoy the following rights and services:

1.Return service: within seven days from the date of sale of the product, the product quality problems, according to the provisions of the national "three packages", in the case of the product appearance and packaging intact, the product will be returned to the seller or tarantula designated places, with the purchase of the valid certificate, return the product you paid for the purchase price.

2. Warranty service: If the product performance failure is detected by AULA after-sales service center within 12 months from the date of purchase, you can enjoy the maintenance service free of charge.

II .The following situations do not belong to the free service scope:

1. Exceeding the specified warranty period;

2. Cannot show the valid warranty certificate or the original serial number label has been altered, replaced, torn and other phenomena;

3. There is no serial number on the product or the product model on the warranty certificate does not match the product in kind;

4. Failure and damage caused by abnormal use, maintenance and storage;

5. Failure or damage caused by repair, change or disassembly of the product by non-authorized maintenance personnel of our company;

6. Failure or damage caused by accidents or other force majeure;

7. Services and additional accessories or gifts outside the product promised by the sales staff are not included in the scope of this warranty service;

8. Failure or damage caused by unstable power supply or voltage.

sales record:

Repair Record:

狼蛛

Commissioned :Shenzhen Soai Electronics Co.,Ltd 委托方：深圳市索艾电子科技有限公司
Commissioned Party (Manufacturer) :Dongguan Soai Electronics Co.,Ltd 受委托方(制造商)：东莞市索艾电子科技有限公司 Soai Industry Park,Huayu Street Changlong
Village Huangjiang Town Dongguan City
Guangdong Province.
广东省东莞市黄江镇长龙村华裕街索艾产业园
Enterprise standard code:GB/T14081-2010
执行标准：GB/T14081-2010
www.aulacn.com
Made in China