EN ISO 20345 PERSONAL PROTECTIVE EQUIPMENT

- SAFETY FOOTWEAR

EN ISO 20345

༹߲ࢺݞጎԢ — Ҿඇၸ

ࡽዚࠅ႑ྲጀ࠲

“PPEَ“॰࠲ް࣮

ጨრܠ߸ڥइ

ࡀ݆PPEࢇޙҾඇၸLjႴᄲڦׇ๨ዞ౹

(Regulation (EU) 2016/425)ڦᄲ൱Ljժᆯ

Notified body৊ႜׂ೗ණኤăEN ISO 20345

๟޿PPE݆ࡀူLj๢ᆩᇀҾඇၸڦၹۙՔጚă

Safety footwear in EU market should comply with the PPE Regulation (EU) 2016/425

and certify by Notified Body. EN ISO 20345 is the harmonized European standards

under the PPE Regulation.

ૌݴ

CLASSIFICATION

ۨᅭ

DEFINITION ๖૩

ᆩೄ߫ईഄ໱֌ଙ዆ڦׯၸLjඇၞঌईඇ਋ࢇ֌ଙၸأྔ

Footwear made from leather and other material,

excluding all-rubber or all polymeric footwear

Class l

Class lI

Hybrid

ඇၞঌ(नྜඇ଼ڦࣅ(ईඇ਋ࢇ֌ଙ(नྜඇఇ዆ڦ(ၸ

All-rubber (i.e. entirely vulcanized) or all-polymeric

(i.e. entirely moulded) footwear

փీࡃૌྺIૌईIIૌၸLj੗ݴंྺࢇ”ፇࢇ“ၸࢅंࢇ”ጀ໒”ၸ

Footwear that cannot be classified as footwear of class I or II,

and can be divided into hybrid “moulded” footwear and hybrid “

mounted” footwear

ҾඇၸڦՔ๎ૌ՚ MARKING CATEGORIES OF SAFETY FOOTWEAR

ૌ՚

CATEGORY

एԨᄲ൱(՗2ࢅ՗3)

BASIC REQUIREMENTS

(TABLE 2 AND TABLE 3)

ᄲ൱े޹

ADDITIONAL REQUIREMENTS

SBेฉǖ

• ހԿڦၸፗ൶ᇘ

Ⴀۉৢੇ •

• ၸፗ൶ᇘీଉဌ๭

S1ेฉǖ

• ဌ຤Ⴀࢅ঴຤ဌႠ

S2ेฉǖ

Ⴀحِੇ •

ڹྔࣂݞ •

SBेฉǖ

• ހԿڦၸፗ൶ᇘ

Ⴀۉৢੇ •

• ၸፗ൶ᇘీଉဌ๭

S4ेฉǖ

Ⴀحِੇ •

ڹྔࣂݞ •

S2ेฉǖ

຤ݞኝၸ•

S3ेฉǖ

຤ݞኝၸ•

AS SB, PLUS:

• Closed seat region

• Antistatic properties

• Energy absorption of seat region

AS S1, PLUS:

• Water penetration and absorption

AS S2, PLUS:

• Penetration resistance

• Cleated outsole

AS SB, PLUS:

• Closed seat region

• Antistatic properties

• Energy absorption of seat region

AS S4, PLUS:

• Penetration resistance

• Cleated outsole

AS S2, PLUS:

• Water resistance of the whole footwear

AS S3, PLUS:

• Water resistance of the whole footwear

Ư

Ư

Ư

ư

ư

Ư

Ư

S1

S2

S4

S6

SB Ưईư Ưorư

ጀǖྺՍᇀՔ๎LjԨ՗ࡃૌକҾඇၸएԨᄲ൱޹ࢅेᄲ൱ڦፌݘ࠽ፇࢇă

NOTE: For ease of marking, this table categorizes safety footwear with the most

widely used combinations of basic and additional requirements.

S3 (metal insert typeP) or

S3L (non-metalinsert type PL) or

S3S (non-metal insert type PS)

S5 (metal insert type P) or

S5L (non-metal insert type PL) or

S5S (non-metal insert type PS)

S7 (metal insert type P) or

S7L (non-metal insert type PL) or

S7S (non-metal insert type PS)

This standard specifies basic and additional

(optional) requirements for safety

footwear used for general purpose.

• Whole footwear

• Upper

• Lining

• Tongue

• Insole, insock & footbed

• Outsole

The key tests are:

• Impact resistance

• Compression resistance

• Slip resistance

• Penetration resistance

• Antistatic properties

• Energy absorption of seat region

• Water vapour permeability and

coefficient

• Scuff cap abrasion

• Ladder grip

Special risks are covered by

complementary job-related standards

such as:

• EN ISO 20346 Protective footwear

• EN ISO 20347 Occupational footwear

• EN 15090 Footwear for firefighters

• EN 50321Electrical insulating

footwear

• EN ISO 17249 Protection against

chain saw injuries

• EN 13832 Protection against

chemicals

• EN 20349 Molten metal splash

• EN 13634 Protection for

motorcycle riders

EN ISO 20345ࡀۨକҾඇၸڦएԨᄲ

ࡤᄲ൱ԈԨᄲ൱ăएे޹(ڦ჋੗)ࢅ൱

և࿋ᆶǖڦ

• ኝၸ

• ၸӻ

૛ת •

• ၸบ

ضগࢅۈĂၸڹా •

ڹྔ •

ഄዐ࠲ڦ॰ၜణᆶǖ

• ၸཀྵੇ؋ऍ

• ၸཀྵੇუ໫

ࣂݞ •

حِݞ •

ۉৢੇ •

๭ଉဌ߶ీࢫ •

• ຤ኖഘาཪᇑဣຕ

ఉၸཀྵఱఉႠݞ •

• ᄦ࿡൶ᇘ༱ႚጃ࿥঳ࠓ

ڦᆌܔ໱ഄLjᆯࢺݞڦዖ߾๺ᇀ༬ܔ

ਏ༹Քጚ৊ႜܔথă૩සǖ

• EN ISO 20346 ࢺݞၸ

• EN ISO 20347 ኰᄽၸ

• EN 15090 ၩݞၸ

• EN 50321ۉਨᇹၸ

• EN ISO 17249 ૾਒ฅࢺݞ࡞

• EN 13832 ࣅბ೗ࢺݞ

• EN 20349 භබূຌݧॸࢺݞ

• EN 13634 ఊྂכ॑๓ᇵࢺݞ

SGSፕྺࡔाࠅණڦዊଉ׵ࢅ႑एጚLj

๟౹௑ණ੗๲඄ߢࠅڦऐࢅࠓᆈࡔණ

ăࠓጚऐ಼ڦ඄๲੗

SGSݰનፔྺ౹௑ߢࠅऐࠓ)NB0598)Lj

ခǗޜࠚႠೠࢇޙڦCEණኤࠃ༵੗

SGS ᆈࡔ)ᇱNB 0120)ᅙԥ๲඄ׯྺ

“Approved Body”Lj੗ӀቷUKCAײႾ

৊ႜࢇޙႠೠࠚധ݀UKCAኤກă

UKCA+CEණኤײႾ ཞ้৊ႜڦᅃበ๕

ມೠݛࠚӄLjन“ᅃอມኤ”Lj੗ᆶၳ

०ࣅୁײLj໫܌ණኤዜ೺Ljইگණኤ้

क़ׯԨLjे໏ׂ೗ࡀࢇฉ๨Lj஢ፁׂ೗

ཞ้ሞᆈࢅࡔׇ๨௑౹ၨ๳ᄲ൱ă

As a globally recognized benchmark

of quality and integrity, SGS is the

authorized Notified Body by European

Union and Approved Body by UK.

SGS Finland, as an EU notified body

(NB0598), can provide CE certification

compliance assessment services;

SGS UK (formerly NB 0120) has been

authorized as \"approved body\", which

can conduct compliance assessment

according to UKCA procedures and

issue UKCA certificates.

SGS proposed one-stop scheme,

called \"One application, CE+UKCA

certification\". By applying once and

carries out CE + UKCA compliance

assessment procedures at the same

time. It effectively simplifies the

process, shortens the certification

TAT. Then PPE products can meet

the requirements of UK and EU

markets at the same time.

ᇀSGS࠲

About SGS

SGS้ชᇑޜ੔๦रޜခ

૴ဣටǖރר౰๗

ࣆۉǖ+86 (0)21 6107 2840

ᆰၒǖsoftline.cn@sgs.com

૴ဣ࿢்

07/24/EN ISO 20345_V3 © SGS Société Générale de Surveillance SA. (2024)

www.sgs.com

www.sgsonline.com.cn

REVISION OF ASTM F2413-18 STANDARD SPECIFICATION FOR

PERFORMANCE REQUIREMENTS FOR PROTECTIVE FOOTWEAR

ெՔҾඇၸՔጚ߸ႎǖ

ASTM F2413-18

ࡽዚࠅ႑ྲጀ࠲

“PPEَ“॰࠲ް࣮

ጨრܠ߸ڥइ

ASTM F2413߃ࡥକᆶࢺݞԈཀྵ߾ڦፕၸڦ

ڦዖփཞܠᆩᇀ๢ᄲ൱LjگፌڦీႠࢺݞ

߾ፕ࣍ৣăሞ߸ႎڦ2018ӲዐLjᆶᅃ߲ዘ

փৈႴᄲᆶۈِحݞࢅፕၸ߾ǖࣅՎڦۇٴ

ڼႴᄲᆶᆯ࣏LjߢԒ֪๬ڦ๪ᄓํݛෙڼ

ෙݛํᄓ๪؜ਏࢇޙڦႠำ௽(COC)ă

ASTM F2413๟ெࡔኰᄽҾඇᇑॳ੃࠶૙ਆ

(OSHA)ڦᆅᆩ࿔ॲኮᅃLjཞ้ᄺ๟ெࡔ૴Ӻ

݆ࡀ)CFR)ڦᆅᆩՔጚăഄዐLj29 CFR Part

1910.132؜ߴକPPEڦएԨᄲ൱Lj29 CFR

Part 1910.136 (a)ኸ؜Ljࠧᇵሞᅜူᆶޅ၃

߾ڦፕׇ໯LjՂႷحጣࢇޙASTM F2413ᄲ

൱ڦҾඇၸǖ

• ᆶᅺ࿿༹ۚ஌ܸሖฅޅڦ၃

• ᆶၸڹԥِ೦ޅڦ၃

• ᆶԥۉऍޅڦ၃

ASTM F2413 covers minimum requirements for the performance of footwear to

provide protection against a variety of workplace hazards that can potentially result in

injury. In the 2018 version, test report and Certification of Conformance (COC) are

required to be issued by a third-party laboratory for the safety hazard(s) applicable to

the footwear or/and puncture resistant devices.

Protective footwear requirements are referenced in the Occupational Safety and

Health Administration’s (OSHA’s) Code of Federal Regulations (CFR) Title 29. General

Personal Protective Equipment (PPE) requirements are given in section 1910.132 and

Foot Protection requirements in section 1910.136. 29 CFR. 29 CFR Part 1910.136 (a)

states that employees must wear safety shoes that meet ASTM F2413 requirements

in the following workplaces at risk:

• Risk of falling objects

• Risk of the sole being punctured

• Risk of electric shock

ASTM F2413߃ࡥକҾඇၸԍࢺႠీڦፌگᄲ൱Ljഄዐǖ

ASTM F2413-18 COVERS MINIMUM REQUIREMENTS FOR THE DESIGN, PERFORMANCE, TESTING AND CLASSIFICATION OF

PROTECTIVE FOOTWEAR.

ഽ዆ Mandatory

ഽ዆ Mandatory

ᆶُႠీ้ If applicable

ᆶُႠీ้ If applicable

ᆶُႠీ้ If applicable

ᆶُႠీ้ If applicable

ᆶُႠీ้ If applicable

ੇ؋ऍ Impact Resistant Footwear (I)

ఱუ໫ Compression Resistant Footwear (C)

ḧࠡ؋ऍࢺݞ Metatarsal protection (Mt)

ۉڞႠ Conductive protection (Cd)

ੇߛუ Electric hazard protection (EH)

ੇৢۉ Static dissipative protection (SD)

حݞ ِPuncture resistance (PR)

I

C

Mt

Cd

EH

SD 10/35/100

PR

ࢇޙႠ COMPLIANCE ࢺݞႠీ PROTECTION PERFORMANCE Քऻ MARKING

All footwear manufactured to the ASTM specification must be marked with the

compliance to the specific portion of the standard. One shoe of each pair must be

clearly and legibly marked (stitched in, stamped on, pressure sensitive label, etc.) on

the inside or outside surface of the tongue, gusset, shaft or quarter lining. The marking

must be enclosed in a rectangular border and a three-line format is suggested.

ࢇޙASTM F2413ڦҾඇၸLjՂႷᆶܔᆌ

ࢺݞڦႠీՔऻࢅՔധăၸጱڦՔധՂႷ

ൣည੗९(੗ᅜᆩފכĂᆇຘĂუ௺Քധڪ

ݛ๕)ں࿋ᇀၸบĂෙঙೌĂ჏ཤईࢫ૛ా

ڦ՗֨ా௬ईྔ֨՗௬ăՔऻՂႷ࿋ᇀᅃ

3ႜǖྺ׉௬Ljཚ઀૛ݛ߲

֪๬ԒߢᆌԈڍࡤփ၌ᇀᅜူ႑တǖ

• ڼෙݛํᄓ๪ڦఁ׬Lj૴ဣ႑တत๲඄

ധఁ

ຎဦ௮ၘڦۈِحݞፕၸई߾ •

• ߾ፕၸईحݞِڦۈՔ๎(૩සׂ೗ဣଚLj

႙༹ࡽLjSKUڪ(Ă؅ஓĂఴၸई౰ၸ

• ֪๬ᄲ൱

ࡕ঳๬֪ •

ࢇޙႠำ௽(COC)ᆌԈڍࡤփ၌ᇀᅜ

ူ႑တǖ

• ڼෙݛํᄓ๪ڦఁ׬Lj૴ဣ႑တत๲඄

ധఁ

׬ఁິࠅڦ௽Ⴀำࢇޙฤ൩•

• ߾ፕၸईحݞِڦۈՔ๎(૩සׂ೗ဣଚLj

႙༹ࡽLjSKUڪ(Ă؅ஓĂఴၸई౰ၸ

೺නิၳڦ௽Ⴀำࢇޙ •

• ࢇޙႠำ௽ᅈ਍ڦ๬֪Ԓࡽߢஓ

• ำ௽ׂ೗ӀASTM F2412ܔᆌڦ๬֪ݛ݆

֪๬ࢫLjഄ঳ࢇޙࡕASTM F2413-18ڦ

֪๬ᄲ൱

THE TEST REPORT INCLUDING THE FOLLOWING INFORMATION, BUT ARE NOT

LIMITED TO THEM:

• Name of the third-party laboratory, contact information and authorization signature(s)

• Full description of the sample footwear and/or puncture resistant devices tested

• Any manufacturer’s reference (product category, style, model, SKU etc.), size and

gender

• Performance requirements and safety hazard(s)

• Results, test conditions and if any modification of the test methods

THE DECLARATION OF CONFORMITY (COC) SHOULD INCLUDE, BUT IS NOT LIMITED

TO, THE FOLLOWING INFORMATION:

• Name of the third-party laboratory, contact information and authorization signature(s)

• Name of the company issued the Certificate of Compliance (COC)

• All manufacturer’s references (product category, style, model, SKU, etc)

• Certification issue date

• Report number and issue date associated with the Certificate of Compliance (COC)

• Statement that the manufacturer’s reference meets the performance requirements

of ASTM Specification F2413-18 as tested in accordance with ASTM Test Methods

F2412-18 and list the safety hazard(s) tested

ASTM F2413

M/F

I

C

Mt

Cd

EH

SD 10/35/100

PR

ࢇޙႠำ௽!Comply with ASTM F2413

ఴၸई౰ၸ!Male or Female

ੇ؋ऍ!Impact Resistance

ఱუ໫!Compression Resistance

ḧࠡ؋ऍࢺݞ!Metatarsal Protection

ۉڞႠ!Conductive Protection

ੇߛუ!Electric Hazard Protection

ੇৢۉ!Static Dissipative Protection

حݞ!ِPuncture Resistance

ڼᅃႜ One

ڼܾႜ Two

ڼෙႜ Three

ഽ዆!Mandatory

ഽ዆!Mandatory

ഽ዆!Mandatory

ഽ዆!Mandatory

ᆶُႠీ้!If applicable

ᆶُႠీ้!If applicable

ᆶُႠీ้!If applicable

ᆶُႠీ้!If applicable

ᆶُႠీ้!If applicable

ႜຕ LINE Քऻ MARKING ຫ௽ EXPLANATION ࢇޙႠ COMPLIANCE ਉ૩ EXAMPLE

ASTM F2413-18

M/I/C

Mt EH

૴ဣ࿢் CONTACT US

SGS้ชᇑޜ੔๦रޜခ

૴ဣටǖރר౰๗

ࣆۉǖ+86 (0)21 6107 2840

ᆰၒǖsoftline.cn@sgs.com

07/24/ASTM F2413-18_V4 © SGS Société Générale de Surveillance SA. (2024)

www.sgs.com

www.sgsonline.com.cn