该页无缩略图
沈阳瑞思达轴承有限公司SHENYANG TOTAL BEARING CO.,LTD.
Tel: 024 22945833 22923833 24853899 Fax: 024 88729249
Mobile: 13940483518 15640413155（微信）
Web: https://www.rstbearing.com.cn
To receive a copy of the DODGE Bearing
Engineering Catalog, DODGE Gearing
Engineering Catalog or DODGE Power
Transmission Components Engineering
Catalog, contact your local authorized
DODGE Distributor or Baldor Electric Co.,
P.O. Box 499, 6040 Ponders Court, Greenville, SC 29602.
Prices and data indicated in this document are for your convenience and were correct
at time of printing with the exception of clerical and/or printing errors. Possession of this
document by any person or company is not to be construed as an offer to sell to him or to
anyone else the goods listed herein at the prices stated.
ALL DATA AND PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE and shall be subject to
those prices in effect at time of shipments. All published and quoted prices are based upon
the application of, and all sales are expressly subject to, the Company’s Standard Terms and
Conditions of Sales are available upon request. This document supersedes all previously
published catalog/pricing documents.
WARNING: Because of the possible danger to person(s) or property from accidents which may result from the improper use of products, it is important that correct procedures
be followed: Products must be used in accordance with the engineering information specified in the catalog. Proper installation, maintenance and operation procedures must be
observed. The instructions in the instruction manuals must be followed. Inspections should be made as necessary to assure safe operation under prevailing conditions. Proper
guards and other suitable safety devices or procedures as may be described or as may be specified in safety codes should be provided, and are neither provided by Baldor Electric
Company nor are the responsibility of Baldor Electric Company. This unit and its associated equipment must be installed, adjusted and maintained by qualified personnel who are
familiar with the construction and operation of all equipment in the system and the potential hazards involved. When risk to persons or property may be involved, a holding device
must be an integral part of the driven equipment beyond the speed reducer output shaft.
WARNING
The information provided for Product Interchange in this catalog is
for use only as a general reference by persons qualified to recognize
unreasonable selection options. Products suggested as substitutes may
have dimensional, rating, pricing and other differences from products
to be replaced. This selection method must be used in conjunction with
the applicable product catalog which contains important precautions and
other pertinent information.
In illustrations throughout this catalog, safety guards have
been removed for photographic purposes. © 2007 Baldor Electric Company
DODGE Products are
Manufactured in ISO 9002
Certified Plants
AERO™
AIRTROL®
APEX®
AUTOMATE®
AUTOMAX®
Brand X™
BRONZOIL DESIGN®
CALIBRE™
DAGGRE™
DODGE®
DODGE DOUBLE-INTERLOCK®
DOUBLE-INTERLOCK®
DUTY MASTER®
DYNA V®
DYNA V DESIGN®
DYN-ADJUST®
DYNAFACE®
DYNA-SYNC®
ELECTRO-CRAFT®
ENDURASEAL®
E-Z KLEEN®
E-Z KLEEN™
FIRST LINE®
FLEXALIGN®
FLEXIDYNE®
FLEXLINK®
FLEXPAK®
GRID-LIGN®
GRIP TIGHT®
GRUNT MAN (Design only)®
GRUNT WORK AND DESIGN®
HYDROIL®
IMPAK®
INVERTRON®
Below is a list of registered and trademarked names in the U.S.A.
LIBERATOR®
LODE-SPHER®
MASTER®
MASTER and Design™
MAXPAK®
MAXUM®
METRE®
MINE DUTY EXTRA®
MOTO DRIVE®
MOTODRIVE®
MOTOMATIC®
MOTO-MATIC®
NYLIGN®
PARAFLEX®
PARA-FLEX®
PLS®
POLYBAND®
POLY-DISC®
POLY-FLEX®
POWER LEAN®
QUANTIS®
REEVES®
RELIALUBE®
RELIANCE®
RELIANCE (IN KATAKANA)®
RELIANCE AUTOMATION®
RELIANCE DESIGN®
RELIANCE ELECTRIC®
RELIANCE V S DESIGN®
RELIANCE V*S DESIGN®
ROLLING GRIP®
RPM AC™
RPM III™
SCHOOL OF TRANSMISSIONEERING®
SCR DESIGN®
SERVICELINE®
SLEEVOIL DESIGN®
SLEEVOL®
SOLIDLUBE®
SPEEDSETTER®
STAREC®
TAPER-LOCK®
TCO APPRAISAL™
TCO TOOLBOX®
TIGEAR®
TIGEAR-2™
TIGER TORQUE®
TORQUE-ARM™
TORQUE-TAMER®
TRANSMISSIONEER®
TRANSMISSIONEERING®
TRI-MATIC®
TYPE E-XTRA®
ULTIMA®
ULTRA KLEEN™
UNIBRAKE®
UNIFIED®
UNISPHERE®
V S®
V*S®
V*S DESIGN®
VARI-SPEED®
VARI-SPIN®
VIA VISA®
VS STAR DEVICE®
WEBPAK®
WEBPAKCS®
CONTENTS
DODGE BEARING CATALOG
QUICK REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . REFERENCE GUIDE-1
BALL BEARING INDEX . . . . . . . . . . . . . . . . . . . . . . BALL BEARING INDEX-1
E-Z KLEEN® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-1
GRIP TIGHT® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2-1
SETSCREW BALL BEARING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3-1
ECCENTRIC COLLAR BALL BEARINGS . . . . . . . . . . . . . . . . . . . . . . . . . B4-1
D-LOK™ BALL BEARINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5-1
THE E-FAMILY ROLLER BEARINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6-1
SPECIALITY TAPERED PRODUCTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7-1
S-2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8-1
UNISPHERE II® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B9-1
IMPERIAL - ISN™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B10-1
UNIFIED® SAF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B11-1
INTERNATIONAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B12-1
SLEEVE BEARINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13-1
SLEEVOIL® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B14-1
TAKE-UP FRAMES & BASE PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . B15-1
ENGINEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B16-1
PART NUMBER INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1
KEY WORD INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29
main_toc.indd 1 3/26/07 9:50:03 AM
沈阳瑞思达轴承有限公司SHENYANG TOTAL BEARING CO.,LTD.
Tel: 024 22945833 22923833 24853899 Fax: 024 88729249
Mobile: 13940483518 15640413155（微信）
Web: https://www.rstbearing.com.cn
NOTES
main_toc.indd 2 3/26/07 9:50:03 AM
Food & Beverage Ball Bearings,
Page B1-2
ó Two types: polymer housed
units and stainless steel
housed units
ó Two inserts: corrosion resistant
(comparable to 440
stainless steel) and standard
steel insert with fl ingers
ó Three locking styles: 65°
setscrew angle (SC), concentric
clamp collar (GT), and thin wall adapter (GT)
ó Single-lip contact seal with fl ingers (standard), end covers
available from stock
ó Optional—BEV modifi cation for the beverage industry
ó Interchangeable mounting dimensions with most competitive
products
ó Anti-rotation device prevents insert rotation associated with light
or rotating loads/high-speed applications
ó Plus or minus 2° static misalignment
Polymer-Housed Polymer Sleeve Bearings
Page B1-2
ó Polymer housing contains additive that
prevents bacterial and fungal growth
ó All polymer and stainless steel
construction
ó Solid polymer housing has no cavities
and no fi llings
ó Conforms to FDA /USDA specifi cations
ó Polymer sleeve insert with stainless steel
anti-rotation pin
ó No lubrication required, self-lubricated polymer sleeve insert for
maintenance-free operation
ó Offered in a wide variety of housing confi gurations and all
popular bore sizes
ó Operates in temperatures from -40°F to 180°F
ó 3/4 - 1-15/16 size
GRIP-TIGHT Ball Bearings,
Page B2-1
ó Two types: normal duty GT and
medium duty GTM
ó Single-lip contact seal with
fl ingers (standard), low-torque
labyrinth seal (optional), end
covers available from stock
ó Interchangeable mounting
dimensions with most
competitive products
ó Thin Wall Adapter mounting offers 360° full shaft contact
and concentricity. No shaft marring or fretting corrosion like
setscrew and eccentric collar products. Built in bearing puller
easily removes the bearing from the shaft. Turned, ground, and
polished shafting is not required.
ó Anti-rotation device prevents insert rotation associated with light
or rotating loads/high-speed applications
ó Expansion and non-expansion pillow blocks available for popular
shaft sizes
ó High-temperature option available to 400°F
ó Plus or minus 2° static misalignment
Setscrew Ball Bearings,
Page B3-1
ó Four types: normal duty SC,
medium duty SCM, intermediate
duty VSC, and light duty SL
ó Single-lip contact seal (standard),
single-lip contact seal with
fl ingers (optional on SC and
SCM), low-torque labyrinth seal
(optional on SC and SCM), end
covers available from stock for SC, SCM and VSC
ó Interchangeable mounting dimensions with most competitive
products
ó 65° setscrew angle for greater holding power and ease on
installation in confi ned areas
ó Anti-rotation device on SC and SCM bearings prevents insert
rotation associated with light or rotating loads/ high-speed
applications
ó Expansion and non-expansion pillow blocks available for popular
SC shaft sizes
ó High-temperature option available to 400° F on SC and SCM
ó Plus or minus 2° static misalignment
REFERENCE GUIDE -1
REFERENCE GUIDE
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
ref_guide.indd -1 3/26/07 9:08:10 AM
REFERENCE GUIDE-2
Bearing Quick Reference
REFERENCE GUIDE
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
Eccentric Collar Ball Bearings,
Page B4-1
ó Three types: normal duty SXR,
intermediate duty SXV, and light duty
SLX
ó Single-lip contact seal (standard),
single-lip contact seal with fl ingers
(optional on SXR), low-torque
labyrinth seal (optional on SXR), end
covers available from stock for SXR
and SXV
ó Interchangeable mounting dimensions with most competitive
products
ó Eccentric collar locks the bearing to the shaft by a quarter turn of
the collar in direction of shaft rotation collar is secured in place
with setscrew
ó Anti-rotation device on SXR prevents insert rotation associated
with light or rotating loads/high-speed applications
ó Expansion and non-expansion pillow blocks available for popular
SXR shaft sizes
ó High-temperature option available to 400°F on SXR
ó Plus or minus 2° static misalignment
D-LOK Ball Bearings,
Page B5-1
ó Two types: normal duty DL and
medium duty DLM
ó Single-lip contact seal with
fl ingers (standard),
low-torque labyrinth seal
(optional), end covers
available from stock
ó Interchangeable mounting dimensions with most competitive
products
ó Concentric clamp collar locks the bearing to the shaft by
tightening a single Allen wrench cap screw, the bearing will
not mar the shaft like setscrew and eccentric collar bearings,
provides concentricity between the bearing and shaft
ó Anti-rotation device prevents insert rotation associated with light
or rotating
ó Expansion and non-expansion pillow blocks available for popular
shaft sizes
ó High-temperature option available to 400°F
ó Plus or minus 2° static misalignment
Air Handling Ball Bearings,
Page B2-12, B3-14,
B5-66,
ó Thin wall adapter: normal duty
GTAH and medium duty GTMAH
ó Setscrew: normal duty (SCAH)
and medium duty (SCMAH)
Concentric clamp collar: normal
duty (DLAH) and medium duty
(DLMAH)
ó Single-lip contact seal (standard
on SCAH and SCMAH), single-lip contact seal with fl ingers
(optional on SCAH and SCMAH, standard on DLAH, DLMAH and
GTAH, GTMAH), low-torque labyrinth seal (optional), end covers
available from stock
ó Interchangeable mounting dimensions with most competitive
products
ó Anti-rotation device prevents insert rotation associated with light
or rotating loads/high-speed applications
ó Pus or minus 2° static misalignment
ó Expansion and non-expansion pillow blocks available for popular
shaft sizes
ó High-temperature option available to 400°F
Type E Tapered Roller Bearings (E-XTRA),
Page B6-1
ó Tapered rolling elements
ó Completely assembled, factory
adjusted, and properly
lubricated—shaft ready
ó Extra protection—E-TECT™ seal
option
ó Comparable mounting
dimensions with ball bearings
ó E-XTRA allows easy upgrade from ball bearings
Double-Interlock Tapered Roller Bearings,
Page B6-1
ó Tapered roller bearing durability in a
variety of styles
ó Extra protection E-TECT seal option
ó Special clearances and greases available
ó Self aligning
ó Factory assembled, adjusted, and lubricated—shaft ready
ó Sealed bearing
ref_guide.indd -2 3/26/07 9:08:12 AM
REFERENCE GUIDE-3
REFERENCE GUIDE
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
Type K Tapered Roller Bearings,
Page B6-1
ó Tapered roller bearing with reduced
length through bore
ó Single collar design saves space and
installation time
ó Allows bearing to be closer to the
load for reduced shaft design
ó Self aligning
ó Factory assembled, adjusted, and lubricated—shaft ready
ó Same housing as double-interlock
ó Extra protection-E-TECT™ Seal Option
TAF Tapered Roller Bearings
Page B6-1
ó Tapered bearing is a cost-saving
alternative to SAF spherical bearings
ó Shaft ready—mounts six times faster
than SAF
ó Interchangeable with SAF style pillow
blocks
ó Self aligning, factory assembled,
adjusted, and lubricated
ó E-TECT seal option available up to 5”
ó Optional sensors for speed, vibration, and temperature
ó Up to 5° static misalignment
Type C Specialty Tapered Bearings,
Page B7-1
ó Two single-row tapered bearings press-fi tted
on sleeve
ó Improved concentricity over other collarmounted types of bearings
ó Steel multiple labyrinth seals
ó Rugged two-piece outer housing
ó Positive concentric clamp sleeve mounting
ó Heavy duty gray iron
Special Duty Tapered Roller Bearings,
Page B7-1
ó Quality duplex tapered roller bearing
ó Tapered adapter sleeve mounting
ó Effective piston ring seals
ó Rugged two-piece housing
ó Heavy duty gray iron
S-2000 Spherical Roller Bearings,
Page B8-1
ó High-capacity, double-row spherical
rollers
ó Permits static or dynamic misalignment
up to 2°
ó Factory sealed, lubed, and adjusted
ó Features springlok® collar that acts as a fl inger
ó Available with TRIDENT triple lip labyrinth seal options
ó 65° springlok collar mount for increased holding power vs. 90°
or 120°
ó Setscrew mounted
UNISPHERE II Spherical Roller Bearings
Page B9-1
ó Dimensionally interchangeable with
ball bearings in length through bore,
base-to-center height, and footprint
ó Approximately fi ve times the rating of
ball bearings
ó Features same rolling elements and
installation-ready components as
S-2000
ó Maintains sealing effectiveness with proven “R” seal
ó Tapered seal area maintains seal contact during maximum
misalignment
ó Springlok collar mount with 65° setscrew spacing for optimum
clamping force
Imperial IP Spherical Roller Bearings
Page B10-1
ó Industry’s only push/pull adapter
mount system
ó Available in 2-bolt and 4-bolt
pillow blocks, fl anges,
and take-ups
ó Accepts commercial toleranced
shafting
ó Installation and removal in less than 15 minutes
ó Full concentric shaft attachment with adaptor sleeve mount
ó Virtually eliminates fretting corrosion
ó Capable of withstanding static or dynamic misalignment of ± 1°
ó Shaft-ready out of the box
ó Available with TRIDENT triple lip labyrinth seal options
ref_guide.indd -3 3/26/07 9:08:12 AM
REFERENCE GUIDE-4
Bearing Quick Reference
REFERENCE GUIDE
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
ISAF Spherical Roller Bearings
Page B10-10
ó Dimensionally interchangeable
with SAF style pillow blocks
ó Patented Imperial™ adapter
mounting system
ó Installation and removal in less
than 15 minutes
ó Easy installation—no feeler
gauges needed
ó Available with TRIDENT triple lip labyrinth seal options
ó Full 2° misalignment capability
ó Virtually eliminates fretting corrosion
ó Shaft-ready out of the box, no assembly of components
necessary
USAF Spherical
Roller Bearings
Page B11-30
ó 22200, 22300, 23000, 23100, and
23200 Series
ó Industry-standard dimensions
interchangeable with SAF housings
ó Five sealing options to match most
operating conditions
ó Cast-in dimples locate drill holes for
lube fi tting, vents, sensors, and mounting modifi cations
ó Standard housings have two oversized drains adaptable for
circulating oil systems
ó Pry slots allow easy separation of the pillow block
Split-Spher Spherical Roller Bearings
Page B11-5
ó Split-race spherical bearing
fi ts USAF 500 housings
and replaces bearing and
adapter assemblies
ó Easy to replace without
removing other shaftmounted components
ó Only split-race bearing made to standard SAF pillow block
dimensions
ó Has same OD dimensions as a standard spherical bearing
ó Uses 22200 Series split roller bearings
SNX Spherical Roller Bearings
Page B11-23
ó Dimensionally interchangable plummer
block with metric SN housing
ó General-purpose, high-capacity,
double-row, spherical roller bearings
ó Adapter and direct mount
ó Five different sealing options to match most operating conditions
ó Grease or oil lubrication
HFO Plummer Block Bearings
Page B12-9
ó Plummer block housings with oilconveying ring lubrication
ó Used with 22200, 22300, 22200K,
and 22300K Series spherical roller
bearings
ó Available with labyrinth seals or
end covers
ó Material: gray cast iron
PDNF & BLO..A
Page B12-20 and B12-25
ó Solid housings incorporate
two bearing seats
ó Misalignment is virtually
eliminated
ó PDNF Series is grease
lubricated
ó BLO..A Series is oil
lubricated
ó BLO..A Series is designed for heavy duty service
DFL
Page B12-22
ó Flange mount housings with two
bearing seats
ó DFLS version allows for axial
adjustment of fan impeller location
ó Heavy duty, with double row
spherical or deep groove ball
bearings
ó Standard version is lubricated for life
SOLIDLUBE Sleeve Bearings
Page B13-6
ó Functions in harsh environments
where ball bearing will not
ó Self-lubricating, statically self
aligning
ó Covers a wide range of temperature
extremes
- 700 Series: -40°F to 700°F
- 1000 Series: -200°F to -40°F and 250°F to 1000°F
ó Housing types: 2-bolt pillow blocks, 4-bolt and 2-bolt fl ange
units, and take-up units
ó Ideal where bearings are subject to dry cycles or where lube
systems would be too costly
ó Recommended for slow speeds and limited shaft movement
applications
ó Bore sizes 3/4” to 8”
ref_guide.indd -4 3/26/07 9:08:14 AM
REFERENCE GUIDE-5
REFERENCE GUIDE
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
Babbitted & Bronze Bushed Bearings
Page B13-10
ó Good for slow to medium and
shock loads
ó Good for slow speeds and shock
loads
ó Capable of MPTA load ratings
ó Cast-iron housings in 2- and
4-bolt pillow blocks
ó Babbitted bearing features solid or fully split housing
ó Bronze bushed bearing features fully split housing
ó Bronze bushing is split and easily replaced
BRONZOIL
Page B13-12
ó Feeds oil to shaft with self-oiling
bushing
ó Sleeve bearings with split
pressed steel housing
ó Statically self aligning
ó Features bushing shoulder that provides self-lubricating bearing
thrust face
ó Designed with slotted holes
ó Available with oil-resistant rubber grommets for sound isolation
and static electricity protection
ó Housing types: 2-bolt pillow and 4-bolt fl ange
SLEEVOIL R Series
Hydrodynamic Pillow Block Bearings
Page B14-3
ó Extended life (no metal-to-metal
contact during operation)
ó Handles high speeds
ó Dampens vibration, provides quiet
operation
ó Fully split for ease of maintenance
ó Self aligning
ó Thrust capability
ó External cooling (air, water, or oil) available for hot shafts
SLEEVOIL RTL Series Hydrodynamic
Page B14-4
Pillow Block Bearings
ó Extended life (no metal-to-metal contact
during operation)
ó Handles high speeds
ó Dampens vibration, provides quiet
operation
ó Fully split for ease of maintenance
ó Self aligning
ó Three times the thrust load capability of R Series
ó External cooling (air, water, or oil) available for hot shafts
SLEEVOIL P Series
Pedestal Hydrodynamic Bearings
Page B14-5
ó P Series is used on motors, generators,
fans, test stands, dynamometers,
pumps, compressors, and other turbo
machinery
ó Dimensionally interchangeable with DIN
standard 31690 and ISO 11687-1
ó Meets API and NEMA end-fl oat
specifi cations
ó Fully split components allow trouble-free assembly and
disassembly
ó Circulating oil-ready housing accommodates high speeds,
elevated temperatures, and dirty environments
ó Large-capacity oil sump promotes cooler operation
SLEEVOIL Oil Level
& Filtration System (OLF)
Page B14-38
ó Maintains proper oil level while
bearing is running
ó Increases bearing performance and
life
ó Allows even oil distribution and
cooler operating temperatures
ó Ensures fi ltered clean oil
ó Permits easy fi lter change while bearing is operating
ó Custom-engineered to support SLEEVOIL bearings
Take-Up Frames
Page B15-1
ó 6 take-up frame types available
from stock
ó Standard take-up frame travel
from 1-1/2” to 60”
ó Take-up frames allow for the mounting of Dodge ball, roller, and
sleeve bearings
ó Take-up frame capacity is pre-engineered to exceed bearing
capacity
ó Made to provide/maintain tension and shaft centers on a variety
of belt and chain-type conveyors
ó Hydraulic and pneumatic tensioning available
Smart Products
Page B6-61, B10-66
ó Online monitoring of temperature,
vibration, and speed
ó EZ Link Connects to DeviceNetTM
ó Plug and play installation
ó Available on TAF and USAF
ref_guide.indd -5 3/26/07 9:08:16 AM
BALL BEARING INDEX-1
BALL BEARING INDEX
HOUSING
I
N
S
E
R
T
S
P2B-GT- . . .
B2-8
P2B-GTEZ- . . . PCR
B1-14
P2B-GTEZ- . . CHCR
B1-16
P2B-GTM- . . .
B2-10
TB-GT- . . .
B2-30
TB-GTEZ- . . .PCR
B1-30
F2B-GT- . . .
B1-
F2B-GTEZ-. . .PCR
B1-38
F2B-GTEZ-. . .SCHR
B1-40
F2B-GTM- . . .
B1-
FB-GT -. . .
B1-
FB-GTEZ-. . .PCR
B1-52
P2B-SC-. . .
B3-10 - B3-14
P2B-SCRZ-. . .PCR
B1-18
P2B-SCRZ-. . .SHCR
B1-20
P2B-SCM- . . .
B3-26 - B3-30
TB-SC- . . .
B3-42
TB-SCRZ-. . .PEC
B1-32
F2B-SC- . . .
B3-44 - B3-46
F2B-SCRZ- . . .PCR
B1-42
F2B-SCEZ -. . .SHCR
B1-44
F2B-SCM- . . .
B3-54
LFT-SC- . . .
B3-60
FB-SC- . . .
B3-64
FB-SCRZ-. . .PCR
B1-54
LF-SC- . . .
B3-66
P2B-VSC- . . .
B3-32 - B3-34
F2B-VSC- . . .
B3-58
F2B-SL- . . .
B3-62
F3B-SL- . . .
B3-68
P2B-SXR- . . .
B4-10 - B4-14
TB-SXR- . . .
B4-28
F2B-SXR- . . .
B4-32
FB-SXR- . . .
B4-
P2B-SXV- . . .
B4-20 - B4-24
TB-SXV- . . .
B4-30
F2B-SXV- . . .
B4-34
F2B-SLX- . . .
B4-42
LFT-SXV- . . .
B4-40
LF-SXV- . . .
B4-44
F3B-SLX- . . .
B4-46
P2B-DL- . . .
B5-8 - B5-12
P2B-DLEZ . . .PCR
B1-24
P2B-DLEZ-SHCR
B1-26
P2B-DLM- . . .
B5-14 - B5-16
TB-DL- . . .
B5-20
TB-DLEZ . . . PCR
B1-34
F2B-DL- . . .
B5-22
F2B-DLEZ . . .PCR
B1-46
F2B-DLEZ . . .SHCR
B1-48
F2B-DLM- . . .
B5-24
LFT-DL- . . .
B5-28
FB-DL- . . .
B5-32
FB-DLEZ . . . PCR
B1-56
LF-DL- . . .
B5-30
Not Recommended
Made to Order / Modifi cation Required
P2BTB- F2B- LFT- FBSC, SCM
VSCSXRsxvGT
ball_bearing_index.indd 2 3/26/07 9:19:41 AM
BALL BEARING INDEX-2
BALL BEARING INDEX
HOUSING
I
N
S
E
R
T
S
F4B-GT- . . .
B2-48
F4B-GTEZ . . . PCR
B1-60
F4B-GTEZ . . .SHCR
B1-62
F4B-GTM- . . .
B2-50
FC-GT- . . .
B2-64
FC-GTM- . . .
B2-66
F4B-SC- . . .
B3-70 - B3-72
F4B-SCRZ . . . PCR
B1-64
F4B-SCRZ . . . SHCR
B1-66
F4B-SCM- . . .
B3-78
FC-SC- . . .
B3-86
FC-SCM- . . .
B3-88
NSTU-SC- . . .
NTSU-SCM- . . .
TP-G- . . .
B3-90 - B3-92
WSTU-SCEZ. . .PCR
B1-78
WSTU-SC- . . .
WSTU-SCM- . . .
TP-G- . . .
B3-98 - B3-100
HNG-SC- . . .
B3-114
SCHB-SC- . . .
B3-116
CYL-SC- . . .
B3-118
F4B-VSC- . . .
B3-82
F4B-SL- . . .
B3-84
WSTU-VSC- . . .
B3-106
NSTU-VSC- . . .
B3-96
F4B-SXR- . . .
B4-48 FC-SXR- . . .
WSTU-SXR- . . .
NSTU-SXR- . . .
TP-GXR- . . .
B4-62, B4-64
B4-66
HNG-SXR- . . .
B4-70
SCHB-SXR- . . .
B4-72
CYL-SXR- . . .
B4-74
F4B-SXR- . . .
B4-52
F4B-SLX- . . .
B4-54
FC-SXV- . . .
B4-34
NSTU-SXV- . . .
WSTU-SXV- . . .
B4-62 - B4-66
F4B-DL- . . .
B5-34
F4B-DLEZ . . . PCR
B1-68
F4B-DLEZ . . .SHCR
B1-70
F4B-DLM- . . .
B5-36 - B5-38
FC-DL- . . .
B5-40
FC-DLM- . . .
B5-42
NSTU-DL- . . .
NSTU-DLM- . . .
B5-44 - B5-46
WTSU-DLEZ. . .PCR
B1-78
WSTU-DL- . . .
WSTU-DLM- . . .
B5-48 - B5-50
TP-DL, TPDLM
B5-52 - B5-54
SCHB-DL . . .
B5-56
CYL-DL- . . .
B5-58
Not Recommended
Made to Order / Modifi cation Required
F4B- FC- NSTU-WSTUTP- HNG- SCHB- CYLSC, SCM
VSCSXRsxvGT
ball_bearing_index.indd 3 3/26/07 9:19:42 AM
BALL BEARING INDEX-3
NOTES
ball_bearing_index.indd Sec1:4 3/26/07 9:19:42 AM
B1-1
CONTENTS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
E-Z KLEEN Polymer and Stainless Steel Housed Ball & Sleeve Bearings
Features / Benefi ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-2
How to Order / Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-4
Easy Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-5
Dimensions
Pillow Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-14
Tapped Base Pillow Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-30
2 Bolt Flange Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-38
Flanged Bracketed Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-54
3 Bolt Flange Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-58
4 Bolt Flange Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-60
Wide Slot Take-Up Bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-74
Inserts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-80
Interchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-88
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1-90
Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1
Key Word Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-34
ezkleen_toc.indd B1-1 3/23/07 10:40:15 AM
沈阳瑞思达轴承有限公司SHENYANG TOTAL BEARING CO.,LTD.
Tel: 024 22945833 22923833 24853899 Fax: 024 88729249
Mobile: 13940483518 15640413155（微信）
Web: https://www.rstbearing.com.cn
B1-2
Bearing Quick Reference
FEATURES/BENEFITS
E-Z KLEEN Set Screw Ball Bearing Eccentric Collar Ball Bearing GRIP TIGHT Adapter Ball Bearing
Polymer and Stainless Steel Housed Mounted Bearings
Our goal at DODGE is to create the world’s most successful customer.
We do that by listening and responding to our customers’ needs.
Customers in the food and beverage processing industry told us they
needed new and improved products that help make their industry safer
- products that help in the fi ght against contamination from bacteria
such as E. coli, salmonella, and staphylococcus aureus.
DODGE delivered by expanding our high performance E-Z KLEEN line
with this new, improved generation of E-Z KLEEN engineered polymer
housed ball and sleeve bearings and stainless steel housed ball
bearings.
New DODGE
E-Z KLEEN
with solid-based
housing
Competitive bearing with cavities
and fi llings that can trap bacteria
RUGGED, SOLID-BASE HOUSING
• Manufactured with no
cavities and no fi llings
-no traps for bacteria
• 316 Series stainless
steel housing also
available
• Features anti-microbial
polymer that helps
prevent bacterial and
fungal growth (polymer
housing)
• For no relube (NL)
remove the lube fi tting
and install the polymer
plug that is shipped
with each bearing
• Housing strength
exceeds static
capacity of bearing
• Retains dimensional
stability in harsh
environments
• Designed with
stainless steel lube
fi ttings and stainless
steel ferrules in
bolt holes (polymer
housed)
• No fl aking or peeling,
even after repeated
washdowns
• Provides excellent
chemical resistance
• Available with open
enclosed end closures
• FDA/USDA complaint
CORROSION-RESISTANT BALL BEARING
INSERTS
• Corrosion resistant
PROGUARD™ Plus
seal with stainless
steel fl ingers
• FDA/USA approved
synthetic lubricant
• Relubricable
• Anti-rotation pin
• Corrosion-resistant
inner and outer ring
• Reinforced, stabilized
nylon cage
• Stainless steel balls
and lube fi tting
• Offered in inch and
metric sizes
• Stainless steel
setscrews (SC)
and stainless steel
capscrew (DLOK)
• Temperature range
-20° to +225° F
THREE SHAFT
LOCKING
SYSTEMS FROM
STOCK
• SC - Two
stainless-steel
setscrews set
65 apart
• D-LOK -
Corrosion
resistant
concentric collar
• GT-GRIP TIGHT
POPULAR HOUSING
STYLES
Polymer Stainless Steel
• Pillow
blocks
• Pillow Block
• 2 and 4
bolt fl ange
bearings
• Tappedbase pillow
blocks
• 2 and 4
bolt fl ange
bearings
• Flange
brackets
• Wide slot
take-up
bearings
Corrosion Resistant Inner
And Outer Ring Out Performs
Other 400 Series Stainless
Steel Precision Hardened
And Honed Inner And Outer
Rings
Corrosion Resistant
PROGUARD Plus Seal
65° Stainless
Setscrews Locking
Stainless Steel Balls
Stainless Steel Flinger
RESULTS OF HOUSING ANTI-MICROBIAL
ACTIVITY AGAINST TEST ORGANISMS
TEST
ORGANISM
TYPE OF
ORGANISM
GROWTH-FREE
ZONE (MM)
CONTACT
INHIBITION (%)
Staphylococcus aureus Bacterial 0 100
Aspergillus niger Fungal 0 100
ezkleen_fea_ben.indd B1-2 3/23/07 10:40:31 AM
B1-3
FEATURES/BENEFITS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
Polymer and Stainless Steel Housed Mounted Bearings
DODGE
PROGUARD™ PLUS SEAL
Corrosion resistant PROGUARD Plus seal
with fl ingers - a combination contact landriding seal and labyrinth - keeps lubricants in,
contaminants out.
D-LOK DL
PRECISION-HARDENED AND
HONED INNER AND OUTER
RINGS
Precision-hardened and honed inner and
outer rings for wear resistance, quieter
operation, and longer life.
ANTI-ROTATION PIN
Anti-rotation pin prevents rotation of the insert
within the housing.
Simple and effective, it makes inserts easier
to replace.
Stainless Steel Anti-Rotation Pin
POLYMER SLEEVE
E-Z KLEEN POLYMER
HOUSED BEARING WITH
POLYMER SLEEVE INSERT
• Targeted for wet, cool and
coldside environments/
applications
• Self-lubricating polymer sleeve
insert
• All polymer and stainless-steel
construction
• Features stainless-steel
antirotation pin on sphere of
insert
• Resist fungus and bacterial
growth
• Ensures quiet operation
• Conforms to FDA/USDA
specifi cations
• Offered in both inch and meter
sizes
STAINLESS HOUSING
CORROSION RESISTANT PROGUARD PLUS SEAL
Stainless Steel
Bolt Furrule
Antimicrobial Polymer
Housing
Stainless Steel Lube Fitting
Stainless Steel Flinger Anti-Rotation Pin
GRIP-TIGHT LOCKING SYSTEM
Full Contact on shaft for better grip, less vibration.
Setscrew locking can distort the inner ring and cause systeminduced vibration. But with the DODGE GRIP-TIGHT Adapter, the
adapter attaches itself to the shaft for full concentric contact - 360°
through the length of the bearing.
ezkleen_fea_ben.indd B1-3 3/23/07 10:40:31 AM
B1-4
Bearing Quick Reference
HOW TO ORDER/
NOMENCLATURE
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION/DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Polymer and Stainless Steel Housed Mounted Bearings
HOW TO ORDER
There are two ways to specify DODGE polymer-housed ball bearings. Most of the product offerings have part numbers with listings shown throughout this brochure. Use of part numbers ensures accurate order processing.
When part numbers are not shown, the product may be specifi ed by description or part name. This method is used when ordering units that include
modifi cations or options. To order by description for options not covered by the nomenclature.
NOMENCLATURE
P2B - SCHUEZ - 104S = PCR
Modifi cation Or Feature:
CR = Corrosion resistant insert
LL = Low torque labyrinth seal
MOD = Modifi ed
NL = No Lube (sealed for life)
P = Polymer housing
SH = Stainless Steel Housing
Shaft Size
Inches:
First digit = Number of inches
Second & third digits = Number of sixteenths of an inch
104 = Indicates 1-4/16 or 1-1/4
S = Next smaller ring size. E.g. 1-1/4 206 would be written as 104S
L = Next larger ring size. E.g. 1/2 204 would be written as 008L
Metric:
First two digits = number of millimeters
M = Metric
Bearing Type:
SC = Wide inner ring, normal duty, 65° setscrew locking
DL = Wide inner ring, normal duty, concentric clamp collar
GT = Wide inner ring, normal duty, thin wall adapter locking
PS = Polymer Sleeve Insert
Suffi xes to the above:
EZ = EZ-KLEEN (used with polymer or stainless steel housed units)
BEZ = Low backing height pillow block, EZ-KLEEN
UEZ = higher back pillow block, EZ-KLEEN (for interchangeability with
competitive pillow blocks)
Housing:
F2B = 2 bolt fl ange
F4B = 4 bolt fl ange
FB = Flanged bracket
INS = Insert
P2B = Pillow block, 2 bolt base
TB = Tapped base pillow block
WSTU = Wide slot take-up
ezkleen_hto_nom.indd B1-4 3/23/07 10:41:17 AM
B1-5
EASY SELECTION
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
DODGE E-Z KLEEN ball bearings are primarily designed for radial loading.
However, they have the capacity to carry thrust loads and combined
radial/thrust loads. The maximum recommended load which can be applied
is limited by various components in the system, such as bearing, housing,
shaft attachments, speed and life requirements as listed in this catalog
and the instruction manual that accompanies each bearing. DODGE E-Z
KLEEN ball bearings have been applied successfully when these limits
have been exceeded under controlled operating conditions. Contact
DODGE Engineering, 864-281-2195, for applications which exceed these
recommendations.
Select a bearing from the Selection table that has a radial load rating at the
operating speed equal to or greater than the calculated Equivalent Radial
load for a desired L10 life. (Table 2 for English shaft sizes and Table 3 for
metric shaft sizes) This simple method is all that is required for the majority
of general applications and provides for occasional average shock loads.
L10 Hours Life-is the life which may be expected for at least 90% of a given
group of bearings operating under identical conditions.
Heavy Service-For heavy shock loads, frequent shock loads or severe
vibrations, add up to 50% (according to severity of conditions) to the
Equivalent Radial Load to obtain a Modifi ed Equivalent Radial Load. Consult
Application Engineering for additional selection assistance.
A maximum thrust load value of C/10 is recommended as a guide for
general applications and will give adequate L10 life. If the thrust load exceeds
this limit, it is advisable to use auxiliary thrust carrying devices, such as a
shaft shoulder, snap ring, or a thrust collar. Where substantial radial load
pulls the housing away from the mounting base, both the hold-down bolts
and housing must be of adequate strength. Auxiliary load carrying devices,
such as sheer bars, are advisable for side or end-loading of pillow blocks
and radial loads for fl ange units.
To determine the L10 hours life for loads and RPM’s not listed use the
following equation:
Where:
L10= Life, hours
C = Dynamic Capacity, lbs. or N
P = Equivalent Radial Load, lbs. or N
RPM = Revolution per minute
When the load on a ball bearing is solely a radial load with no thrust (axial)
load, the Equivalent Radial Load (P) is equal to the actual radial load.
However, when a thrust (axial) load is applied, the radial and thrust loads
applied must be converted into an Equivalent Radial Load. The use of the X
(radial factor) and Y (thrust factor) from Table 1 convert the actual applied
thrust and radial loads to an Equivalent Radial Load which has the same
effect on the life of a bearing as a radial load of this magnitude.
Selection of DODGE E-Z KLEEN Polymer and Stainless Steel Housed Ball Bearings
P = (X x FR) + (Y x FA
)
Where:
P = Equivalent Radial Load, lbs.
FR= Radial load, lbs.
FA
= Thrust load, lbs.
e = Thrust load to radial load factor (Table 1)
X = Radial load factor (Table 1)
Y = Thrust Factor (Table 1)
CO= Basic static capacity (Table 2 or 3)
To fi nd X and Y, fi rst calculate FA
/CO to determine e. Calculate FA
/FR and
compare to e to determine the X and Y factors to use from Table 1.
Substitute all known values into the Equivalent Radial Load equation. The
Equivalent Radial loads (P) thus determined can be used in the L10 life
formula or compared to the allowable Equivalent Radial Load rating desired
in the expanded rating chart to select a bearing (Table 2).
If calculated value of P is less than FR, use P=FR.
L10= x C 16667 ( )P RPM
Table 1
FA
Co e
Radial/Thrust Factors
If FA
/FR is equal to or
less than e If FA
/FR is greater than e
FA
/FR ≤ e FA
/FR> e
X Y X Y
.014 .19 1 0 0.56 2.30
.021 .21 1 0 0.56 2.15
.028 .22 1 0 0.56 1.99
.042 .24 1 0 0.56 1.85
.056 .26 1 0 0.56 1.71
.070 .27 1 0 0.56 1.63
.084 .28 1 0 0.56 1.55
.110 .30 1 0 0.56 1.45
.170 .34 1 0 0.56 1.31
.280 .38 1 0 0.56 1.15
.420 .42 1 0 0.56 1.04
.560 .44 1 0 0.56 1.00
Shaft Tolerances
Normal Shaft Size
Inches
Recommended Shaft Tolerances
SC & D-LOK Products (Inches)
Recommended Shaft Tolerances
GRIP TIGHT Ball Bearings Inches
Up to 1-1/2” +0.000 -.0005 +0.000 -0.002
Over 1-1/2 to 2” +0.000 -.0010 +0.000 -.0.003
Lubrication- DODGE Ball Bearings are lubricated at the factory and are
ready to run. The bearings are initially lubricated with an aluminum complex
based, H1 Food Grade grease and should be relubricated with the same or
some equivalent. For high speeds, high loads, extreme temperatures and
other abnormal operating conditions, special greases may be required.
Contact DODGE Application Engineering for recommendations on these
types of applications.
Misalignment - DODGE Ball Bearings are designed to allow a maximum
of 2º static misalignment. These bearings are not suitable for dynamic
misalignment. To ensure good alignment, mounting surfaces must be
checked for fl atness and must lie in the same plane. When tightening base
bolts, each bolt should be alternately tightening in incremental torque values
until full torque is achieved to prevent the angular shifting of the pillow block
that occurs when one bolt is tightened to its full torque. Shimming may be
required to minimize misalignment.
3
ezkleen_easy_sel.indd B1-5 5/4/07 2:36:21 PM
B1-6
Bearing Quick Reference
EASY SELECTION
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Table 2 - Easy Selection For Polymer And Stainless Steel Housed E-Z KLEEN
Ball Bearing Mounted Bearings - Inch
RING
SIZE
SHAFT
SIZE
DYNAMIC
CAPACITY
C, lbs.
STATIC
CAPACITY
C0, LBS
L10
LIFE
HOURS
ALLOWABLE EQUIVALENT RADIAL LOAD RATINGS (lbs) AT VARIOUS RPM*
50 150 250 500 750 1000 1500 1750 2000 2500 3000 3500 4500 5000 5500 7500 9500 11000 12000
204 3/4 2899 1390
20000 740 515 435 345 300 275 240 225 215 200 190 180 165 160 155 140 129 123 119
30000 645 450 380 300 260 240 210 200 190 175 165 155 145 140 135 120 113 107 104
40000 590 410 345 275 240 215 190 180 170 160 150 145 130 125 125 110 102 97 95
60000 515 355 300 240 210 190 165 155 150 140 130 125 115 110 105 95 89 85 83
100000 435 300 255 200 175 160 140 130 125 115 110 105 190 95 90 80 75 72 70
205
7/8
15/16
1
3146 1565
20000 805 560 470 375 325 295 260 245 235 220 205 195 180 175 170 150 140 133 129
30000 705 485 410 325 285 260 225 215 205 190 180 170 155 150 145 130 122 116 113
40000 640 445 375 295 260 235 205 195 185 175 165 155 140 135 135 120 111 106 103
60000 560 385 325 260 225 205 180 170 165 150 140 135 125 120 115 105 97 92 90
100000 470 325 275 220 190 175 150 145 135 125 120 115 195 100 100 90 82 78 76
206
1-1/8
1-3/16
1-1/4
4368 2250
20000 1115 775 655 520 455 410 360 340 325 305 285 270 250 240 235 210 194 185
30000 975 675 570 455 395 360 315 300 285 265 250 235 220 210 205 183 170 161
40000 885 615 520 410 360 325 285 270 260 240 225 215 200 190 185 167 154 147
60000 775 535 455 360 315 285 250 235 225 210 200 190 175 165 160 146 135 128
100000 655 455 380 305 265 240 210 200 190 175 165 160 145 140 135 123 113 108
207
1-1/4
1-3/8
1-7/16
5759 3065
20000 1475 1020 860 685 595 545 475 450 430 400 375 355 330 315 305 279 256
30000 1285 890 755 595 520 475 415 395 375 350 330 310 285 275 270 242 224
40000 1170 810 685 545 475 430 375 355 340 315 300 285 260 250 245 220 203
60000 1020 710 595 475 415 375 330 310 300 275 260 250 230 220 215 192 177
100000 860 595 505 400 350 315 275 265 250 235 220 210 190 185 180 162 150
208 1-1/2 7332 4005
20000 1875 1300 1095 870 760 690 605 575 550 510 480 455 420 405 392 352
30000 1640 1135 960 760 665 605 525 500 480 445 420 400 365 355 342 308
40000 1490 1030 870 690 605 550 480 455 435 405 380 360 330 320 310 280
60000 1300 900 760 605 525 480 420 400 380 355 330 315 290 280 270 244
100000 1095 760 640 510 445 405 355 335 320 300 280 265 245 235 229 206
209
1-5/8
1-11/16
1-374
7891 4450
20000 2020 1400 1180 935 820 745 650 615 590 550 515 490 450 435 420 379
30000 1765 1225 1030 820 715 650 570 540 515 480 450 430 395 380 367 331
40000 1600 1110 935 745 650 590 515 490 470 435 410 390 360 345 334 301
60000 1400 970 820 650 570 515 450 430 410 380 360 340 310 300 292 263
100000 1180 820 690 550 480 435 380 360 345 320 300 285 265 255 247 222
210 1-15/16
2 7891 4450
20000 2020 1400 1180 935 820 745 650 615 590 550 515 490 450 434 420
30000 1765 1225 1030 820 715 650 570 540 515 480 450 430 395 379 367
40000 1600 1110 935 745 650 590 515 490 470 435 410 390 360 345 334
60000 1400 970 820 650 570 515 450 430 410 380 360 340 310 301 292
100000 1180 820 690 550 480 435 380 360 345 320 300 285 265 254 247
* SLIGHT INTERFERENCE FIT REQUIRED WHEN OPERATING TO THE RIGHT OF THE HEAVY LINE OR IN THE SHADED AREA. FOR SC PRODUCT ONLY, OR USE D-LOK
OR GT PRODUCTS
Note: Because the allowable loads - especially at low speeds - are extremely high, be sure the shaft strength is adequate and the pillow blocks are base loaded. When
imposed load is horizontal, be sure hold-down bolts are adequate. If bearings are cap loaded, full details on load, speed, and shaft size should be referred to
DODGE Application Engineering.
Use GT with labyrinth seals when operating right of heavy line
ezkleen_easy_sel.indd B1-6 5/4/07 2:36:22 PM
B1-7
EASY SELECTION
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Table 3 - Easy Selection For Polymer And Stainless Steel Housed E-Z KLEEN
Ball Bearing Mounted Bearings - Metric
RING
SIZE
SHAFT
SIZE
DYNAMIC
CAPACITY
C, N
STATIC
CAPACITY
C0, N
L10
LIFE
HOURS
ALLOWABLE EQUIVALENT RADIAL LOAD RATINGS (N) AT VARIOUS RPM*
50 150 250 500 750 1000 1500 1750 2000 2500 3000 3500 4500 5000 5500 7500 9500 11000 12000
204 20mm 12895 6183
20000 3292 2291 1935 1535 1334 1223 1068 1001 956 890 845 801 734 712 689 623 574 547 529
30000 2869 2002 1690 1334 1156 1068 934 890 845 778 734 689 645 623 600 534 503 476 463
40000 2624 1824 1535 1223 1068 956 845 801 756 712 667 645 578 556 556 489 454 431 423
60000 2291 1579 1334 1068 934 845 734 689 667 623 578 556 512 489 467 423 396 378 369
100000 1935 1334 1134 890 778 712 623 578 556 512 489 467 400 423 400 356 334 320 311
205 25mm 13993 6961
20000 3581 2491 2091 1668 1446 1312 1156 1090 1045 979 912 867 801 778 756 667 622 592 574
30000 3136 2157 1824 1446 1268 1156 1001 956 912 845 801 756 689 667 645 578 542 516 503
40000 2847 1979 1668 1312 1156 1045 912 867 823 778 734 689 623 600 600 534 494 472 458
60000 2491 1712 1446 1156 1001 912 801 756 734 667 623 600 556 534 512 467 431 409 400
100000 2091 1446 1223 979 845 778 667 645 600 556 534 512 467 445 445 400 365 347 338
206 30mm 19429 10008
20000 4960 3447 2913 2313 2024 1824 1601 1512 1446 1357 1268 1201 1112 1068 1045 934 862 823
30000 4337 3002 2535 2024 1757 1601 1401 1334 1268 1179 1112 1045 979 934 912 814 756 716
40000 3936 2736 2313 1824 1601 1446 1268 1201 1156 1068 1001 956 890 845 823 743 685 654
60000 3447 2380 2024 1601 1401 1268 1112 1045 1001 934 890 845 778 734 712 649 600 569
100000 2913 2024 1690 1357 1179 1068 934 890 845 778 734 712 645 623 600 547 503 480
207 35mm 25616 13633
20000 6561 4537 3825 3047 2647 2424 2113 2002 1913 1779 1668 1579 1468 1401 1357 1232 1139
30000 5716 3959 3358 2647 2313 2113 1846 1757 1668 1557 1468 1379 1268 1223 1201 1076 996
40000 5204 3603 3047 2424 2113 1913 1668 1579 1512 1401 1334 1268 1156 1112 1090 978 903
60000 4537 3158 2647 2113 1846 1668 1468 1379 1334 1223 1156 1112 1023 979 956 854 787
100000 3825 2647 2246 1779 1557 1401 1223 1179 1112 1045 979 934 845 823 801 720 667
208 40mm 32613 17814
20000 8340 5782 4871 3870 3380 3069 2691 2558 2446 2268 2135 2024 1868 1801 1744 1565
30000 7295 5048 4270 3380 2958 2691 2335 2224 2135 1979 1868 1779 1624 1579 1521 1370
40000 6628 4581 3870 3069 2691 2446 2135 2024 1935 1801 1690 1601 1468 1423 1378 1245
60000 5782 4003 3380 2691 2335 2135 1868 1779 1690 1579 1468 1401 1290 1245 1201 1085
100000 4871 3380 2847 2268 1979 1801 1579 1490 1423 1334 1245 1179 1090 1045 1018 916
209 45mm 35099 19794
20000 8985 6227 5249 4159 3647 3314 2891 2736 2624 2446 2291 2180 2002 1935 1868 1686
30000 7851 5449 4581 3647 3180 2891 2535 2402 2291 2135 2002 1913 1757 1690 1632 1472
40000 7117 4937 4159 3314 2891 2624 2291 2180 2091 1935 1824 1735 1601 1535 1486 1339
60000 6227 4315 3647 2891 2535 2291 2002 1913 1824 1690 1601 1512 1379 1334 1299 1170
100000 5249 3647 3169 2446 2135 1935 1690 1601 1535 1423 1334 1268 1179 1134 1099 988
210 50mm 35099 19794
20000 8985 6227 5249 4159 3647 3314 2891 2736 2624 2446 2291 2180 2002 1931 1868
30000 7851 5449 4581 3647 3180 2891 2535 2402 2291 2135 2002 1913 1757 1686 1632
40000 7117 4937 4159 3314 2891 2624 2291 2180 2091 1935 1824 1735 1601 1535 1486
60000 6227 4315 3647 2891 2535 2291 2002 1913 1824 1690 1601 1512 1379 1339 1299
100000 5249 3647 3069 2446 2135 1935 1690 1601 1535 1423 1334 1268 1179 1130 1099
*SLIGHT INTERFERENCE FIT REQUIRED WHEN OPERATING TO THE RIGHT OF THE HEAVY LINE OR IN THE SHADED AREA. FOR SC PRODUCT ONLY, OR USE D-LOK
OR GT PRODUCTS
Note: Because the allowable loads - especially at low speeds - are extremely high, be sure the shaft strength is adequate and the pillow blocks are base loaded. When
imposed load is horizontal, be sure hold-down bolts are adequate. If bearings are cap loaded, full details on load, speed, and shaft size should be referred to
DODGE Application Engineering.
Use GT with labyrinth seals when operating right of heavy line
ezkleen_easy_sel.indd B1-7 5/4/07 2:36:22 PM
B1-8
Bearing Quick Reference
EASY SELECTION
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Table 4 - Easy Selection For E-Z KLEEN Polymer-Housed Sleeve Bearing Mounted Units - Inch
RADIAL LOAD RATINGS (LBS) AT VARIOUS REVOLUTIONS PER MINUTE (RPM)
Series Shaft
Size Up To 10 25 50 75 100 150 200 250
204 3/4 450 400 375 300 230 175 110 90
205 1 600 550 450 215 235 175 110 90
206 1-3/16
1-1/4 900 800 500 325 250 175 110 90
207 1-1/4
1-7/16 1000 900 600 400 300 175 120 95
208 1-1/2 1400 1200 700 430 320 180 125 95
209 1-11/16
1-3/4 1600 1400 725 435 335 180 125 95
210 1-15/16 1800 1600 750 450 350 185 130 100
RADIAL LOAD RATINGS (LBS) AT VARIOUS REVOLUTIONS PER MINUTE (RPM)
Series Shaft
Size 300 350 400 450 500 550 600 650
204 3/4 60 50 45 40 35 25 20 15
205 1 60 50 45 40 35 25 20 15
206 1-3/16
1-1/4 65 60 50 40 35 30 25 20
207 1-1/4
1-7/16 70 65 55 45 40 35 30
208 1-1/2 70 65 55 45 40 35
209 1-11/16
1-3/4 70 65 55 45 40
210 1-15/16 80 70 60 50 45
Continuous operating temperature: -40 to 180º F
ezkleen_easy_sel.indd B1-8 5/4/07 2:36:22 PM
B1-9
EASY SELECTION
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Table 5 - Easy Selection For E-Z KLEEN Polymer-Housed Sleeve Bearing Mounted Units - Metric
RADIAL LOAD RATINGS (NEWTONS) AT VARIOUS REVOLUTIONS PER MINUTE (RPM)
Series Shaft
Size Up To 10 25 50 75 100 150 200 250
204 20 2000 1775 1665 1330 1020 775 485 400
205 25 2665 2445 2000 1400 1045 775 485 400
206 30 4000 3555 2220 1445 1110 775 485 400
207 35 4445 4000 2665 1775 1330 775 530 420
208 40 6225 5335 3110 1910 1420 8000 555 420
209 45 7115 6225 3220 1930 1490 8000 555 420
210 50 8005 7115 3335 2000 1555 820 575 440
RADIAL LOAD RATINGS (NEWTONS) AT VARIOUS REVOLUTIONS PER MINUTE (RPM)
Series Shaft
Size 300 350 400 450 500 550 600 650
204 20 265 220 200 175 155 110 85 65
205 25 265 220 200 175 155 110 85 65
206 30 285 265 220 175 155 130 110 85
207 35 310 285 240 200 175 155 130
208 40 310 285 240 200 175 155
209 45 310 285 240 200 175
210 50 355 310 265 220 200
Continuous operating temperature: -40 to 82º C
ezkleen_easy_sel.indd B1-9 5/4/07 2:36:23 PM
B1-10
Bearing Quick Reference
EASY SELECTION
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN POLYMER HOUSINGS
General Resistance to Chemical Groups at Room Temperature (20°C/68°F)
Chemical Group Condition Or Subgroup Resistance
Inorganic Acids concentrated -
(non-oxidizing) diluted (1:1) +1.00
highly diluted +1.00
Inorganic Acids concentrated -
(oxidizing) diluted (1:1) -
highly diluted +
Organic Acids concentrated =
diluted (1:1) +
highly diluted +
Bases concentrated -
diluted (1:1) -
highly diluted =
Salt Solutions acidic +
neutral +
basic =
Aliphatic Hydrocarbons +
oils and greases +
Aromatic Hydrocarbons =
phenols -
Halogenated Hydrocarbons perhalogenated +
partially halogenated -
Alcohols monovalent +
polyvalent =
Ketones =
Esters =
Ethers +
(1) except hydrofl uoric acid
(+) excellent resistance ( = ) good-fair resistance ( - ) fair-poor resistance ( blank ) no data available
ezkleen_easy_sel.indd B1-10 5/4/07 2:36:23 PM
B1-11
EASY SELECTION
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
CHEMICAL RESISTANCE CHART
Chemical Agent Solution Conc.
@ 23°C @ 60°C @ 80°C
(73°F) (140°F) (175°F)
Polymer Polymer Polymer Polymer Polymer
Housing Insert Housing Insert Housing
A
Acetic Acid 5% + + = =
Acetic Acid 10% + = =
Acetic Acid 20% =-=-=
Acetic Acid 80% =-=-=
Acetic Acid 100% = = =
Acetone = =
Ammonium Chloride 10% + +
Ammonium Hydroxide 10% = -
Ammonium Hydroxide conc. -
Aniline + = =
B
Benzene ====
Bleaching Lye + +
Brake Fluid +++++
Butane +
Butanol = =
Butyl Acetate + =
C
Calcium Chloride 5% + + +
Calcium Chloride 10% + +
Calcium Hydroxide 10% + +
Calcium Hypochlorite + +
Carbon Disulphide +
Carbon Tetrachloride + +
Castor Oil +
Chloroform -
Chromic Acid 40% + - -
Citric Acid 10% + + +
Cottonseed Oil + + +
Cresol - - -
D
Detergents 1% + + = -
Detergents 25% + + = -
Dibutyl Phthalate + +
Diesel Oil +
Dioxane + = - =
E
Ethanol + =
Ether (diethyl-) +
Ethyl Acetate = =
Ethylene Dichloride -
( + ) excellent resistance ( = ) good-fair resistance ( - ) fair-poor resistance ( blank ) no data available
ezkleen_easy_sel.indd B1-11 5/4/07 2:36:23 PM
B1-12
Bearing Quick Reference
EASY SELECTION
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
CHEMICAL RESISTANCE CHART
Chemical Agent Solution Conc.
@ 23°C @ 60°C @ 80°C
(73°F) (140°F) (175°F)
Polymer Polymer Polymer Polymer Polymer
Housing Insert Housing Insert Housing
F
Ferrous Chloride 5% +
Formic Acid 5% + = +
Formic Acid 90% = - -
Freon 11 +
G
Gasoline + +
Glycerol (Glycerin) = =
Glycol = =
Grease +++++
H
Heptane +
Hexane + + +
Hydrochloric Acid 10% +-=--
Hydrochloric Acid 90% -----
Hydrofl uoric Acid 5% - - -
Hydrofl uoric Acid 50% - - -
Hydrogen Peroxide 3% + +
Hydrogen Peroxide 30% = +
IJ
Isoamyle Alcohol = =
Isopropanol = =
KL
Kerosene + + +
Lithium Chloride 43% + +
M
Methanol + = =
Methylene Chloride - + -
Methyl Ethyl Ketone ++=+
Methyl Salicylate +
Mineral Oil +++++
Motor Oils +++++
N
Nitric Acid 10% +-=-=
Nitric Acid 40% -----
Nitric Acid 70% -----
O
Oleic Acid 100% + + +
Olive Oil +++++
P
Perchloroethylene +===
Petroleum Ether +
Phenol = - - -
( + ) excellent resistance ( = ) good-fair resistance ( - ) fair-poor resistance ( blank ) no data available
ezkleen_easy_sel.indd B1-12 5/4/07 2:36:23 PM
B1-13
EASY SELECTION
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
DIMENSIONS
PAGE B1-14
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
CHEMICAL RESISTANCE CHART
Chemical Agent Solution Conc.
@ 23°C @ 60°C @ 80°C
(73°F) (140°F) (175°F)
Polymer Polymer Polymer Polymer Polymer
Housing Insert Housing Insert Housing
P
Phosphoric Acid 3% + + +
Phosphoric Acid 30% +-+-+
Phosphoric Acid 85% +-+--
Potassium Chloride 10% + = -
Potassium Dichromate 10% +
Potassium Hydroxide 1% - - -
Potassium Hydroxide 10% - - -
Potassium Hydroxide 60% - - -
Potassium Permanganate 10% + + +
S
Silicone Fluids + + +
Soap Solution 1% ++== -
Sodium Bicarbonate 10% + = -
Sodium Bisulfate 5% +
Sodium Bisulfi te 5% + -
Sodium Bisulfi te 10% + - = -
Sodium Carbonate 10% + - -
Sodium Carbonate 20% + - -
Sodium Chloride 10% ++=+-
Sodium Hydroxide 1% - - -
Sodium Hydroxide 10% - - - -
Sodium Hydroxide 60% - - -
Sodium Hypochlorite 5% + -
Sodium Hypochlorite 10% + = -
Sulfuric Acid 3% +-+-+
Sulfuric Acid 30% +-+--
Sulfuric Acid 98% -----
T
Tetrahydofuran =
Toulene + =
Transformer Oil +++++
Trichlorethylene =
Triethylamine = =
Turpentine +
V
Vaseline + + +
Vegetable Oils +++++
W
Water ++==-
White Spirits +
X
Xylene +
( + ) excellent resistance ( = ) good-fair resistance ( - ) fair-poor resistance ( blank ) no data available
ezkleen_easy_sel.indd B1-13 5/4/07 2:36:24 PM
B1-14
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ Normal Duty Polymer Housed Pillow Blocks
Series Shaft
Size
Complete Unit Unit without Adapter Adapter & Nut Assembly
Part No. Description Part No. Description Part No. Description
204 3/4 129244 P2B-GTEZ-012-PCR 129530 P2B-GTEZ-04-PCR 129967 AN-GT-04-012-CR
20mm 129245 P2B-GTEZ-20M-PCR 129980 AN-GT-04-20M-CR
205 1 129246 P2B-GTEZ-100-PCR 129531 P2B-GTEZ-05-PCR 129968 AN-GT-05-100-CR
25mm 129247 P2B-GTEZ-25M-PCR 129981 AN-GT-05-25M-CR
206
(GTU)
1-1/8 @ P2B-GTUEZ-102-PCR
129536 P2B-GTUEZ-06-PCR
129969 AN-GT-06-102-CR
1-3/16 129248 P2B-GTUEZ-103-PCR 129602 AN-GT-06-103-CR
1-1/4 129249 P2B-GTUEZ-104S-PCR 129603 AN-GT-06-104S-CR
30mm 129250 P2B-GTUEZ-30M-PCR 129611 AN-GT-06-30M-CR
207
1-1/4 129251 P2B-GTEZ-104-PCR
129532 P2B-GTEZ-07-PCR
129972 AN-GT-07-104-CR
1-3/8 129392 P2B-GTEZ-106-PCR 129973 AN-GT-07-106-CR
1-7/16 129252 P2B-GTEZ-107-PCR 129974 AN-GT-07-107-CR
35mm 129253 P2B-GTEZ-35M-PCR 129983 AN-GT-07-35M-CR
208
(GTB)
1-1/2 129254 P2B-GTBEZ-108-PCR 129535 P2B-GTBEZ-08-PCR 129606 AN-GT-08-108-CR
40mm 129255 P2B-GTBEZ-40M-PCR 129613 AN-GT-08-40M-CR
209
1-11/16 129256 P2B-GTEZ-111-PCR
129533 P2B-GTEZ-09-PCR
129976 AN-GT-09-111-CR
1-3/4 129396 P2B-GTEZ-112-PCR 129977 AN-GT-09-112-CR
45mm 129257 P2B-GTEZ-45M-PCR 129985 AN-GT-09-45M-CR
210
1-15/16 129258 P2B-GTEZ-115-PCR
129534 P2B-GTEZ-10-PCR
129978 AN-GT-10-115-CR
2 129393 P2B-GTEZ-200-PCR 129979 AN-GT-10-200-CR
50mm 129259 P2B-GTEZ-50M-PCR 129986 AN-GT-10-50M-CR
ezkleen_sel_dim.indd B1-14 3/23/07 1:22:17 PM
B1-15
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ Normal Duty Polymer Housed Pillow Blocks
Series Shaft
Size
Weight
lbs
kg
ABC
D F
Bolt
Dia.
G H J L M R# S# Z min. max.
204 3/4 0.9 1-15/32 5-1/32 1-31/64 3-43/64 3-59/64 3/8 19/32 39/64 2-5/8 1-1/2 1-5/16 31/64 63/64 1-3/64
20 mm 0.4 37.3 127.8 37.7 93.3 99.6 M10 15.1 15.5 66.7 38.1 33.3 12.3 25 26.6
205 1 1.1 1-29/64 5-1/2 1-31/64 3-31/32 4-13/64 3/8 19/32 39/64 2-55/64 1-51/64 1-7/16 1/2 61/64 1-1/64
25 mm 0.5 36.9 139.7 37.7 100.8 106.8 M10 15.1 15.5 72.6 45.6 36.5 12.8 24.2 25.8
206
(GTU)
1-1/8 1.8 1-39/64 6-5/16 1-25/32 4-39/64 4-57/64 1/2 23/32 45/64 3-11/32 2-5/64 1-11/16 17/32 1-5/64 1-1/8
1-3/16 1.7
1-1/4 1.6
30 mm 0.8 40.9 160.3 45.2 116.9 124.2 M12 18.3 17.9 84.9 52.8 42.9 13.5 27.4 28.6
207
1-1/4 2.5 1-5/8 6-35/64 1-7/8 4-13/16 5-1/8 1/2 23/32 23/32 3-57/64 2-3/8 1-7/8 9/16 1-1/16 1-9/64
1-3/8 2.4
1-7/16 2.4
35 mm 1.1 41.3 166.3 47.6 122.2 130.2 M12 18.3 18.3 98.8 60.3 47.6 14.3 27 29.0
208
(GTB)
1-1/2 3.0 1-27/32 7-13/64 2-7/64 5-7/64 5-41/64 1/2 7/8 49/64 4-11/64 2-5/8 1-15/16 21/32 1-3/16 1-15/64
40 mm 1.4 46.8 183.0 53.6 129.6 143.3 M12 22.2 19.4 106 66.7 49.2 16.7 30.2 31.4
209
1-11/16 3.4 1-55/64 7-13/64 2-7/64 5-31/32 5-27/64 1/2 7/8 27/32 4-5/16 2-5/64 2-1/8 21/32 1-3/16 1-9/32
1-3/4 3.3
45 mm 1.6 47.2 183.0 53.6 137.7 151.6 M12 22.2 21.4 109.5 72.6 54 16.7 30.2 32.5
210
1-15/16 4.2 1-55/64 8-1/16 2-23/64 6 6-9/16 5/8 1 59/64 4-9/16 3-1/8 2-1/4 21/32 1-13/64 1-9/32
2 4.1
50 mm 1.7 47.2 204.8 59.9 152.4 166.7 M16 25.4 23.4 115.9 79.4 57.2 16.7 30.6 32.5
#R & S dimensions will vary slightly depending on true shaft diameter
ezkleen_sel_dim.indd B1-15 3/23/07 1:22:18 PM
B1-16
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Series Shaft
Size
Complete Unit Unit Without Adapter Adapter & Nut Assembly
Part No. Description Part No. Description Part No. Description
204 3/4 129260 P2B-GTEZ-012-SHCR 129559 P2B-GTEZ-04-SHCR 129967 AN-GT-04-012-CR
20mm 129261 P2B-GTEZ-20M-SHCR 129980 AN-GT-04-20M-CR
205 1 129262 P2B-GTEZ-100-SHCR 129560 P2B-GTEZ-05-SHCR 129968 AN-GT-05-100-CR
25mm 129263 P2B-GTEZ-25M-SHCR 129981 AN-GT-05-25M-CR
206
1-1/8 064994 P2B-GTEZ-102-SHCR
129561 P2B-GTEZ-06-SHCR
129969 AN-GT-06-102-CR
1-3/16 129264 P2B-GTEZ-103-SHCR 129970 AN-GT-06-103-CR
1-1/4 @ P2B-GTEZ-104S-SHCR 129971 AN-GT-06-104-CR
30mm @ P2B-GTEZ-30M-SHCR 129982 AN-GT-06-30M-CR
1-1/8 @ P2B-GTUEZ-102-SHCR
129566 P2B-GTUEZ-06-SHCR
129969 AN-GT-06-102-CR
206 1-3/16 129265 P2B-GTUEZ-103-SHCR 129602 AN-GT-06-103-CR
(GTU) 1-1/4 129266 P2B-GTUEZ-104S-SHCR 129605 AN-GT-06-104S-CR
30mm 129267 P2B-GTUEZ-30M-SHCR 129612 AN-GT-06-30M-CR
207
1-1/4 129268 P2B-GTEZ-104-SHCR
129562 P2B-GTEZ-07-SHCR
129972 AN-GT-07-104-CR
1-3/8 067678 P2B-GTEZ-106-SHCR 129973 AN-GT-07-106-CR
1-7/16 129269 P2B-GTEZ-107-SHCR 129974 AN-GT-07-107-CR
35mm 129270 P2B-GTEZ-35M-SHCR 129983 AN-GT-07-35M-CR
208 1-1/2 129271 P2B-GTEZ-108-SHCR 129563 P2B-GTEZ-08-SHCR 129975 AN-GT-08-108-CR
40mm @ P2B-GTEZ-40M-SHCR 129984 AN-GT-08-40M-CR
208 1-1/2 129272 P2B-GTBEZ-108-SHCR 129565 P2B-GTBEZ-08-SHCR 129606 AN-GT-08-108-CR
(GTB) 40mm 129273 P2B-GTBEZ-40M-SHCR 129613 AN-GT-08-40M-CR
210
1-15/16 129274 P2B-GTEZ-115-SHCR 129978 AN-GT-10-115-CR
2 @ P2B-GTEZ-200-SHCR 129564 P2B-GTEZ-10-SHCR 129979 AN-GT-10-200-CR
50mm 129275 P2B-GTEZ-50M-SHCR 129986 AN-GT-10-50M-CR
ezkleen_sel_dim.indd B1-16 3/23/07 1:22:18 PM
B1-17
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Shaft Weight D F
Series Size lbs A B C Bolt G H J L M R# S# Z
kg min. max. Dia.
204 3/4 1.46 1-15/32 5 1 3-3/8 4-3/16 3/8 27/32 1/2 2-1/2 1-1/2 1-5/16 31/64 63/64 1-3/64
20mm 0.65 37.3 127.0 25.4 85.7 106.4 M10 21.4 12.7 63.5 38.1 33.3 12.3 25 26.7
205 1 1.92 1-29/64 5-1/2 1-1/8 3-11/16 4-1/2 3/8 27/32 17/32 2-23/32 1-51/64 1-7/16 1/2 61/64 1-1/64
25mm 0.83 36.9 139.7 28.6 93.7 114.3 M10 21.4 13.5 68.7 45.6 36.5 12.7 24.2 25.9
206
1-1/8 2.60 1-39/64 6-1/4 1-1/4 4-17/64 5 1/2 15/16 17/32 3-1/8 2-5/64 1-5/8 17/32 1-5/64 1-1/8
1-3/16
1-1/4
30mm 1.18 40.9 158.8 31.8 108.3 127 M12 23.8 13.5 79.4 52.8 41.3 13.5 27.4 28.7
206
(GTU)
1-1/8 2.65 1-39/64 6-1/4 1-1/4 4-17/64 5 1/2 15/16 19/32 3-3/16 2-5/64 1-11/16 17/32 1-5/64 1-1/8
1-3/16
1-1/4
30mm 1.18 40.9 158.8 31.8 108.3 127 M12 23.8 15.1 81.0 52.8 42.9 13.5 27.4 28.7
207
1-1/4 3.83 1-5/8 6-1/2 1-3/8 4-11/16 5-7/16 1/2 15/16 9/16 3-5/8 2-3/8 1-7/8 9/16 1-1/16 1-9/64
1-3/8
1-7/16
35mm 1.75 41.3 165.1 34.9 119.1 138.1 M12 23.8 14.3 92.1 60.3 47.6 14.3 27 29.1
208 1-1/2 4.90 1-27/32 7 1-1/2 5-3/16 6 1/2 31/32 3/4 4 2-5/8 2-1/8 21/32 1-3/16 1-15/64
40mm 2.22 46.8 177.8 38.1 131.8 152.4 M12 24.6 19.1 101.6 66.7 54 16.7 30.2 31.5
208
(GTB)
1-1/2 4.85 1-27/32 7 1-1/2 5-3/16 6 1/2 31/32 9/16 3-13/16 2-5/8 1-15/16 21/32 1-3/16 1-15/64
40mm 2.22 46.8 177.8 38.1 131.8 152.4 M12 24.6 14.3 96.8 66.7 49.2 16.7 30.2 31.5
210
1-15/16 6.14 1-55/64 8 1-5/8 5-49/64 6-11/16 5/8 1-9/64 5/8 4-5/16 3-1/8 2-1/4 21/32 1-13/64 1-9/32
2
50mm 2.62 47.2 203.2 41.3 146.4 169.9 M16 29 15.9 109.5 79.4 57.2 16.7 30.6 32.6
#R & S dimensionS will vary slightly depending on true shaft diameter
ezkleen_sel_dim.indd B1-17 3/23/07 1:22:19 PM
B1-18
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY POLYMER HOUSED PILLOW BLOCKS
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert With Flingers
Part No. Description Part No. Description
204
1/2 @ P2B-SCEZ-008L-PCR* @ P2B-SCEZ-008L-P
5/8 068322 P2B-SCEZ-010L-PCR* 064572 P2B-SCEZ-010L-P
3/4 127500 P2B-SCEZ-012-PCR @ P2B-SCEZ-012-P
20 mm 127545 P2B-SCEZ-20M-PCR @ P2B-SCEZ-20M-P
205
7/8 064839 P2B-SCEZ-014-PCR* 062837 P2B-SCEZ-014-P
15/16 058975 P2B-SCEZ-015-PCR* @ P2B-SCEZ-015-P
1 127501 P2B-SCEZ-100-PCR 058597 P2B-SCEZ-100-P
25 mm 127546 P2B-SCEZ-25M-PCR @ P2B-SCEZ-25M-P
206
1-1/8 @ P2B-SCUEZ-102-PCR* 067919 P2B-SCUEZ-102-P
1-3/16 127502 P2B-SCUEZ-103-PCR @ P2B-SCUEZ-103-P
1-1/4 127503 P2B-SCUEZ-104S-PCR 058596 P2B-SCUEZ-104S-P
30 mm 127547 P2B-SCUEZ-30M-PCR @ P2B-SCUEZ-30M-P
207
1-1/4 127504 P2B-SCEZ-104-PCR 065655 P2B-SCEZ-104-P
1-5/16 059722 P2B-SCEZ-105-PCR* @ P2B-SCEZ-105-P
1-3/8 058944 P2B-SCEZ-106-PCR* @ P2B-SCEZ-106-P
1-7/16 127505 P2B-SCEZ-107-PCR 064064 P2B-SCEZ-107-P
35 mm 127548 P2B-SCEZ-35M-PCR @ P2B-SCEZ-35M-P
208
1-1/2 127506 P2B-SCBEZ-108-PCR @ P2B-SCBEZ-108-P
1-5/8 068495 P2B-SCBEZ-110-PCR* @ P2B-SCBEZ-110-P
40 mm 127549 P2B-SCBEZ-40M-PCR @ P2B-SCBEZ-40M-P
209
1-5/8 @ P2B-SCBEZ-110L-PCR* @ P2B-SCBEZ-110L-P
1-11/16 127507 P2B-SCEZ-111-PCR 067996 P2B-SCEZ-111-P
1-3/4 058931 P2B-SCEZ-112-PCR @ P2B-SCEZ-112-P
45 mm 127550 P2B-SCEZ-45M-PCR @ P2B-SCEZ-45M-P
210
1-15/16 127508 P2B-SCEZ-115-PCR 056497 P2B-SCEZ-115-P
2 057898 P2B-SCEZ-200-PCR @ P2B-SCEZ-200-P
50 mm 127551 P2B-SCEZ-50M-PCR @ P2B-SCEZ-50M-P
@ Assembled to order * 20 piece minimum
ezkleen_sel_dim.indd B1-18 3/23/07 1:22:19 PM
B1-19
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Shaft
Series
Weight
lbs
kg
D F
Bolt
Dia.
Size A B C G H J L M R S
min. max.
204
1/2 0.68 1-5/32 5-1/32 1-31/64 3-43/64 3-59/64 3/8 19/32 39/64 2-5/8 1-1/8 1-5/16 27/64 47/64
5/8 0.66
3/4 0.64
20 mm 0.30 29.4 127.8 37.7 93.3 99.6 M10 15.1 15.5 66.7 28.6 33.3 10.7 18.7
205
7/8 0.73 1-3/16 5-1/2 1-31/64 3-31/32 4-13/64 3/8 19/32 39/64 2-55/64 1-21/64 1-7/16 27/64 49/64
15/16 0.71
1 0.69
25 mm 0.32 30.2 139.7 37.7 100.8 106.8 M10 15.1 15.5 72.6 33.7 36.5 10.7 19.4
206
1-1/8 1.15 1-25/64 6-5/16 1-25/32 4-39/64 4-57/64 1/2 23/32 45/64 3-11/32 1-37/64 1-11/16 31/64 29/32
1-3/16 1.13
1-1/4 1.11
30 mm 0.51 35.3 160.3 45.2 116.9 124.2 M12 18.3 17.9 84.9 40.1 42.9 12.3 23
207
1-1/4 1.68 1-17/32 6-35/64 1-7/8 4-13/16 5-1/8 1/2 23/32 23/32 3-57/64 1-27/32 1-7/8 1/2 1-1/32
1-5/16 1.63
1-3/8 1.58
1-7/16 1.52
35 mm 0.74 38.9 166.3 47.8 122.2 130.2 M12 18.3 18.3 98.8 46.8 47.6 12.7 26.2
208
1-1/2 2.08 1-11/16 7-13/64 2-7/64 5-7/64 5-41/64 1/2 7/8 49/64 4-11/64 2-3/64 1-15/16 19/32 1-3/32
1-5/8 2.00
40 mm 0.88 42.9 183.0 53.6 129.6 143.3 M12 22.2 19.4 106 52 49.2 15.1 27.8
209
1-5/8 2.41 1-23/32 7-13/64 2-7/64 5-27/64 5-31/32 1/2 7/8 27/32 4-5/16 2-7/32 2-1/8 19/32 1-1/8
1-11/16 2.34
1-3/4 2.27
45 mm 1.03 43.7 183.0 53.6 137.7 151.6 M12 22.2 21.4 109.5 56.4 54 15.1 28.6
210
1-15/16 2.65 1-3/4 8-1/16 2-23/64 6 6-9/16 5/8 1 59/64 4-9/16 2-7/16 2-1/4 19/32 1-5/32
2 2.58
50 mm 1.30 44.5 204.8 59.9 152.4 166.7 M16 25.4 23.4 115.9 61.9 57.2 15.1 29.4
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY POLYMER HOUSED PILLOW BLOCKS
ezkleen_sel_dim.indd B1-19 3/23/07 1:22:20 PM
B1-20
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert with Flingers
Part No. Description Part No. Description
204
1/2 @ P2B-SCEZ-008L-SHCR @ P2B-SCEZ-008L-SH
5/8 068236 P2B-SCEZ-010L-SHCR* @ P2B-SCEZ-010L-SH
3/4 127670 P2B-SCEZ-012-SHCR 059870 P2B-SCEZ-012-SH
20mm 127697 P2B-SCEZ-20M-SHCR @ P2B-SCEZ-20M-SH
205
7/8 056553 P2B-SCEZ-014-SHCR* 049996 P2B-SCEZ-014-SH
15/16 067839 P2B-SCEZ-015-SHCR* @ P2B-SCEZ-015-SH
1 127671 P2B-SCEZ-100-SHCR 056796 P2B-SCEZ-100-SH
25mm 127698 P2B-SCEZ-25M-SHCR @ P2B-SCEZ-25M-SH
206
1-1/8 @ P2B-SCEZ-102-SHCR* 056548 P2B-SCEZ-102-SH
1-3/16 127672 P2B-SCEZ-103-SHCR 056797 P2B-SCEZ-103-SH
1-1/4 127674 P2B-SCEZ-104S-SHCR 067630 P2B-SCEZ-104S-SH
30mm @ P2B-SCEZ-30M-SHCR @ P2B-SCEZ-30M-SH
1-1/8 @ P2B-SCUEZ-102-SHCR* @ P2B-SCUEZ-102-SH
206 1-3/16 127673 P2B-SCUEZ-103-SHCR @ P2B-SCUEZ-103-SH
(SCU) 1-1/4 127675 P2B-SCUEZ-104S-SHCR @ P2B-SCUEZ-104S-SH
30mm 127699 P2B-SCUEZ-30M-SHCR @ P2B-SCUEZ-30M-SH
@ Assembled to order
*20 piece minimum
ezkleen_sel_dim.indd B1-20 3/23/07 1:22:20 PM
B1-21
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Shaft
Size
Weight
lbs
kg
D F
Bolt
Dia.
Series A B C G H J L M R S
min. max.
204
1/2 1.39 1-5/32 5 1 3-3/8 4-3/16 3/8 27/32 1/2 2-1/2 1-1/8 1-5/16 27/64 47/64
5/8 1.35
3/4 1.31
20mm 0.59 29.4 127.0 25.4 85.7 106.4 M10 21.4 12.7 63.5 28.6 33.3 10.7 18.7
205
7/8 1.65 1-3/16 5-1/2 1-1/8 3-11/16 4-1/2 3/8 27/32 17/32 2-23/32 1-21/64 1-7/16 27/64 49/64
15/16 1.62
1 1.59
25mm 0.73 30.2 139.7 28.6 93.7 114.3 M10 21.4 13.5 69.1 33.7 36.5 10.7 19.4
206
1-1/8 2.37 1-25/64 6-1/4 1-1/4 4-17/64 5 1/2 15/16 17/32 3-1/8 1-37/64 1-5/8 31/64 29/32
1-3/16 2.33
1-1/4 2.29
30mm 1.06 35.3 158.8 31.8 108.3 127 M12 23.8 13.5 79.4 40.1 41.3 12.3 23
206
(SCU)
1-1/8 2.48 1-25/64 6-1/4 1-1/4 4-17/64 5 1/2 15/16 19/32 3-3/16 1-37/64 1-11/16 31/64 29/32
1-3/16 2.44
1-1/4 2.39
30mm 1.11 35.3 158.8 31.8 108.3 127 M12 23.8 15.1 81 40.1 42.9 12.3 23
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
ezkleen_sel_dim.indd B1-21 3/23/07 1:22:20 PM
B1-22
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert with Flingers
Part No. Description Part No. Description
207
1-1/4 127676 P2B-SCEZ-104-SHCR 059798 P2B-SCEZ-104-SH
1-3/8 @ P2B-SCEZ-106-SHCR* 056525 P2B-SCEZ-106-SH
1-7/16 127677 P2B-SCEZ-107-SHCR 059799 P2B-SCEZ-107-SH
35mm 127700 P2B-SCEZ-35M-SHCR @ P2B-SCEZ-35M-SH
208
1-1/2 127678 P2B-SCEZ-108-SHCR 056565 P2B-SCEZ-108-SH
1-5/8 @ P2B-SCEZ-110-SHCR* 062874 P2B-SCEZ-110-SH
40mm @ P2B-SCEZ-40M-SHCR @ P2B-SCEZ-40M-SH
208 1-1/2 127679 P2B-SCBEZ-108-SHCR @ P2B-SCBEZ-108-SH
(SCB) 40mm 127701 P2B-SCBEZ-40M-SHCR @ P2B-SCBEZ-40M-SH
210
1-11/16 @ P2B-SCMEZ-111-SHCR @ P2B-SCMEZ-111-SH
1-15/16 127680 P2B-SCEZ-115-SHCR 056800 P2B-SCEZ-115-SH
2 @ P2B-SCEZ-200-SHCR 062879 P2B-SCEZ-200-SH
50mm 127702 P2B-SCEZ-50M-SHCR @ P2B-SCEZ-50M-SH
@ Assembled to order
*20 piece minimum
ezkleen_sel_dim.indd B1-22 3/23/07 1:22:21 PM
B1-23
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Shaft
Series
Weight
lbs
kg
D F
Bolt
Dia.
Size A B C G H J L M R S
min. max.
207
1-1/4 3.36 1-17/32 6-1/2 1-3/8 4-11/16 5-7/16 1/2 15/16 9/16 3-5/8 1-27/32 1-7/8 1/2 1-1/32
1-3/8 3.25
1-7/16 3.19
35mm 1.47 38.9 165.1 34.9 119.1 138.1 M12 23.8 14.3 92.1 46.8 47.6 12.7 26.2
208
1-1/2 4.39 1-11/16 7 1-1/2 5-3/16 6 1/2 31/32 3/4 4 2-3/64 2-1/8 19/32 1-3/32
1-5/8
40mm 1.95 42.9 177.8 38.1 131.8 152.4 M12 24.6 19.1 101.6 52 54 15.1 27.8
208 1-1/2 3.93 1-11/16 7 1-1/2 5-3/16 6 1/2 31/32 9/16 3-13/16 2-3/64 1-15/16 19/32 1-3/32
(SCB) 40mm 1.74 42.9 177.8 38.1 131.8 152.4 M12 24.6 14.3 96.8 52 49.2 15.1 27.8
210
1-11/16 5.14 1-3/4 8 1-5/8 5-49/64 6-11/16 5/8 1-9/64 5/8 4-5/16 2-7/16 2-1/4 19/32 1-5/32
1-15/16 5.09
50mm 2.29 44.6 203.2 41.3 146.4 169.9 M16 29 15.9 109.5 61.9 57.2 15.1 29.4
ezkleen_sel_dim.indd B1-23 3/23/07 1:22:21 PM
B1-24
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert With Flingers
Part No. Description Part No. Description
204 3/4 127578 P2B-DLEZ-012-PCR @ P2B-DLEZ-012-P
20 mm 127623 P2B-DLEZ-20M-PCR @ P2B-DLEZ-20M-P
205
7/8 @ P2B-DLEZ-014-PCR* @ P2B-DLEZ-014-P
15/16 @ P2B-DLEZ-015-PCR* @ P2B-DLEZ-015-P
1 127579 P2B-DLEZ-100-PCR @ P2B-DLEZ-100-P
25 mm 127624 P2B-DLEZ-25M-PCR @ P2B-DLEZ-25M-P
1-1/8 @ P2B-DLUEZ-102-PCR* @ P2B-DLUEZ-102-P
206 1-3/16 127580 P2B-DLUEZ-103-PCR @ P2B-DLUEZ-103-P
(DLU) 1-1/4 127581 P2B-DLUEZ-104S-PCR @ P2B-DLUEZ-104S-P
30 mm 127625 P2B-DLUEZ-30M-PCR @ P2B-DLUEZ-30M-P
207
1-1/4 127582 P2B-DLEZ-104-PCR @ P2B-DLEZ-104-P
1-3/8 @ P2B-DLEZ-106-PCR* @ P2B-DLEZ-106-P
1-7/16 127583 P2B-DLEZ-107-PCR @ P2B-DLEZ-107-P
35 mm 127626 P2B-DLEZ-35M-PCR @ P2B-DLEZ-35M-P
208 1-1/2 127584 P2B-DLBEZ-108-PCR @ P2B-DLBEZ-108-P
(DLB) 40 mm 127627 P2B-DLBEZ-40M-PCR @ P2B-DLBEZ-40M-P
209
1-5/8 057442 P2B-DLEZ-110L-PCR* @ P2B-DLEZ-110L-P
1-11/16 127585 P2B-DLEZ-111-PCR @ P2B-DLEZ-111-P
1-3/4 062875 P2B-DLEZ-112-PCR* @ P2B-DLEZ-112-P
45 mm 127628 P2B-DLEZ-45M-PCR @ P2B-DLEZ-45M-P
210
1-15/16 127586 P2B-DLEZ-115-PCR @ P2B-DLEZ-115-P
2 058516 P2B-DLEZ-200-PCR @ P2B-DLEZ-200-P
50 mm 127629 P2B-DLEZ-50M-PCR @ P2B-DLEZ-50M-P
@ Assembled to order * 20 piece minimum
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY POLYMER HOUSED PILLOW BLOCKS
ezkleen_sel_dim.indd B1-24 3/23/07 1:22:21 PM
B1-25
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY POLYMER HOUSED PILLOW BLOCKS
Shaft
Series
Weight
lbs
kg
D F
Bolt
Dia.
Size A B C G H J L M R S
min. max.
204 3/4 0.92 1-9/32 5-1/32 1-31/64 3-43/64 3-59/64 3/8 19/32 39/64 2-5/8 1-45/64 1-5/16 1/2 25/32
20 mm 0.42 32.5 127.8 37.7 93.3 99.6 M10 15.1 15.5 66.7 43.3 33.3 12.7 19.8
205
7/8 1.32 1-7/16 5-1/2 1-31/64 3-31/32 4-13/64 3/8 19/32 39/64 2-55/64 2 1-7/16 9/16 7/8
15/16 1.22
1 1.12
25 mm 0.51 36.5 139.7 37.7 100.8 106.8 M10 15.1 15.5 72.6 50.8 36.5 14.3 22.2
206
(DLU)
1-1/8 1.83 1-9/16 6-5/16 1-25/32 4-39/64 4-57/64 1/2 23/32 45/64 3-11/32 2-7/32 1-11/16 5/8 15/16
1-3/16 1.73
1-1/4 1.63
30 mm 0.79 39.7 160.3 45.2 116.9 124.2 M12 18.3 17.9 84.9 56.4 42.9 15.9 23.8
207
1-1/4 2.46 1-3/4 6-35/64 1-7/8 4-13/16 5-1/8 1/2 23/32 23/32 3-57/64 2-11/16 1-7/8 11/16 1-1/16
1-3/8 2.41
1-7/16 2.36
35 mm 1.13 44.5 166.3 47.8 122.2 130.2 M12 18.3 18.3 98.8 68.3 47.6 17.5 27.0
208
(DLB)
1-1/2 3.01 2 7-13/64 2-7/64 5-7/64 5-41/64 1/2 7/8 49/64 4-11/64 2-47/64 1-15/16 3/4 1-1/4
40 mm 1.39 50.8 183.0 53.6 129.6 143.3 M12 22.2 19.4 106 69.5 49.2 19.1 31.8
209
1-5/8 3.51 2 7-13/64 2-7/64 5-27/64 5-31/32 1/2 7/8 27/32 4-5/16 2-63/64 2-1/8 3/4 1-1/4
1-11/16 3.41
1-3/4 3.31
45 mm 1.56 50.8 183.0 53.6 137.7 151.6 M12 22.2 21.4 109.5 75.8 54 19.1 31.8
210
1-15/16 4.17 2-3/32 8-1/16 2-23/64 6 6-9/16 5/8 1 59/64 4-9/16 3-15/64 2-1/4 3/4 1-11/32
2 4.07
50 mm 1.68 53.2 204.8 59.9 152.4 166.7 M16 25.4 23.4 115.9 82.2 57.2 19.1 34.1
ezkleen_sel_dim.indd B1-25 3/23/07 1:22:22 PM
B1-26
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Series Shaft
Size
Part
No. Description
204 3/4 127715 P2B-DLEZ-012-SHCR
20mm 127739 P2B-DLEZ-20M-SHCR
205
7/8 @ P2B-DLEZ-014-SHCR*
15/16 @ P2B-DLEZ-015-SHCR*
1 127716 P2B-DLEZ-100-SHCR
25mm 127740 P2B-DLEZ-25M-SHCR
206
1-1/8 @ P2B-DLEZ-102-SHCR*
1-3/16 127717 P2B-DLEZ-103-SHCR
1-1/4 127718 P2B-DLEZ-104S-SHCR
30mm 127741 P2B-DLEZ-30M-SHCR
206
(DLU)
1-1/8 @ P2B-DLUEZ-102-SHCR*
1-3/16 @ P2B-DLUEZ-103-SHCR
1-1/4 @ P2B-DLUEZ-104S-SHCR
30mm @ P2B-DLUEZ-30M-SHCR
207
1-1/4 127719 P2B-DLEZ-104-SHCR
1-3/8 @ P2B-DLEZ-106-SHCR*
1-7/16 127720 P2B-DLEZ-107-SHCR
35mm 127742 P2B-DLEZ-35M-SHCR
208 1-1/2 127721 P2B-DLEZ-108-SHCR
40mm 127743 P2B-DLEZ-40M-SHCR
208 1-1/2 049469 P2B-DLBEZ-108-SHCR
(DLB) 40mm @ P2B-DLBEZ-40M-SHCR
210
1-11/16 @ P2B-DLMEZ-111-SHCR*
1-15/16 127722 P2B-DLEZ-115-SHCR
50mm 127744 P2B-DLEZ-50M-SHCR
@ Assembled to order *20 piece minimum
ezkleen_sel_dim.indd B1-26 3/23/07 1:22:22 PM
B1-27
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY STAINLESS STEEL HOUSED PILLOW BLOCKS
Shaft
Series
Weight
lbs
kg
D F
Bolt
Dia.
Size A B C G H J L M R S
min. max.
204 3/4 1.46 1-9/32 5 1 3-3/8 4-3/16 3/8 27/32 1/2 2-1/2 1-45/64 1-5/16 1/2 25/32
20mm 0.65 32.5 127.0 25.4 85.7 106.4 M10 21.4 12.7 63.5 43.3 33.3 12.7 19.8
205
7/8 1.92 1-7/16 5-1/2 1-1/8 3-11/16 4-1/2 3/8 27/32 17/32 2-23/32 2 1-7/16 9/16 7/8
15/16 1.87
1 1.82
25mm 0.83 36.5 139.7 28.6 93.7 114.3 M10 21.4 13.5 69.1 50.8 36.5 14.3 22.2
206
1-1/8 2.60 1-9/16 6-1/4 1-1/4 4-17/64 5 1/2 15/16 17/32 3-1/8 11726 1-5/8 5/8 15/16
1-3/16 2.55
1-1/4 2.50
30mm 1.18 39.7 158.8 31.8 108.3 127 M12 23.8 13.5 79.4 56.4 41.3 15.9 23.8
206
(DLU)
1-1/8 2.65 1-9/16 6-1/4 1-1/4 4-17/64 5 1/2 15/16 19/32 3-3/16 2-7/32 1-11/16 5/8 15/16
1-3/16 2.60
1-1/4 2.55
30mm 1.18 39.7 158.8 31.8 108.3 127 M12 23.8 15.1 81 56.4 42.9 15.9 23.8
207
1-1/4 3.83 1-3/4 6-1/2 1-3/8 4-11/16 5-7/16 1/2 15/16 9/16 3-5/8 2-11/16 1-7/8 11/16 1-1/16
1-3/8 3.74
1-7/16 3.66
35mm 1.75 44.5 165.1 34.9 119.1 138.1 M12 23.8 14.3 92.1 68.3 47.6 17.5 27
208 1-1/2 4.90 2 7 1-1/2 5-3/16 6 1/2 31/32 3/4 4 2-47/64 2-1/8 3/4 1-1/4
40mm 2.22 50.8 177.8 38.1 131.8 152.4 M12 24.6 19.1 101.6 69.5 54 19.1 31.8
208
(DLB)
1-1/2 4.85 2 7 1-1/2 5-3/16 6 1/2 31/32 9/16 3-13/16 2-47/64 1-15/16 3/4 1-1/4
40mm 2.22 50.8 177.8 38.1 131.8 152.4 M12 24.6 14.3 96.8 69.5 49.2 19.1 31.8
210
1-11/16 6.14 2-3/32 8 1-5/8 5-49/64 6-11/16 5/8 1-9/64 5/8 4-5/16 3-15/64 2-1/4 3/4 1-11/32
1-15/16 5.77
50mm 2.62 53.2 203.2 41.3 146.4 169.9 M16 29 15.9 109.5 82.2 57.2 19.1 34.1
ezkleen_sel_dim.indd B1-27 3/23/07 1:22:22 PM
B1-28
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
PSEZ POLYMER SLEEVE, POLYMER HOUSED PILLOW BLOCKS
Series Shaft
Size
Part
No. Description
204 3/4 034700 P2B-PSEZ-012-P
20mm 034748 P2B-PSEZ-20M-P
205 1 034701 P2B-PSEZ-100-P
25mm 034749 P2B-PSEZ-25M-P
206
(PSU)
1-3/16 034702 P2B-PSUEZ-103-P
1-1/4 034703 P2B-PSUEZ-104S-P
30mm 034750 P2B-PSUEZ-30M-P
207
1-1/4 034704 P2B-PSEZ-104-P
1-7/16 034705 P2B-PSEZ-107-P
35mm 034751 P2B-PSEZ-35M-P
208
(PSB)
1-1/2 034706 P2B-PSBEZ-108-P
40mm 034752 P2B-PSBEZ-40M-P
210 1-15/16 034709 P2B-PSEZ-115-P
50mm 034754 P2B-PSEZ-50M-P
ezkleen_sel_dim.indd B1-28 3/23/07 1:22:23 PM
B1-29
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
PSEZ POLYMER SLEEVE, POLYMER HOUSED PILLOW BLOCKS
Shaft
Size
Weight
lb.
kg
D F
Bolt
Dia
Series A B C G H J L M
Min Max
204 3/4 0.57 1 5-1/32 1-31/64 3-31/64 3-59/64 3/8 19/32 39/64 2-5/8 1-5/16 1-5/16
20mm 0.26 25.4 127.8 37.7 93.3 99.6 M10 15.1 15.5 66.7 33.3 33.3
205 1 0.57 1-1/16 5-1/2 1-31/64 3-31/32 4-13/64 3/8 19/32 39/64 2-55/64 1-7/16 1-7/16
25mm 0.26 27.0 139.7 37.7 100.8 106.8 M10 15.1 15.5 72.6 36.5 36.5
206
(PSU)
1-3/16 0.89 1-3/16 6-5/16 1-25/32 4-39/64 4-57/64 1/2 23/32 45/64 3-11/32 1-11/16 1-11/16
1-1/4 0.88
30mm 0.4 30.2 160.3 45.2 116.9 124.2 M12 18.3 17.9 84.9 42.9 42.9
207
1-1/4 1.06 1-5/16 6-35/64 1-7/8 4-13/16 5-1/8 1/2 23/32 23/32 3-57/64 2 1-7/8
1-7/16 1.01
35mm 0.48 33.3 166.3 47.8 122.2 130.2 M12 18.3 18.3 98.8 50.8 47.6
208
(PSB)
1-1/2 1.27 1-1/2 7-13/64 2-7/64 5-7/64 5-41/64 1/2 7/8 49/64 4-11/64 2 1-15/16
40mm 0.58 38.1 183.0 53.6 129.6 143.3 M12 22.2 19.4 106.0 50.8 49.2
210 1-15/16 1.67 1-5/8 8-1/16 2-23/64 6 6-9/16 5/8 1.00 59/64 4-9/16 2-9/16 2-1/4
50mm 0.76 41.3 204.8 59.9 152.4 166.7 M16 25.4 23.4 115.9 65.1 57.2
ezkleen_sel_dim.indd B1-29 3/23/07 1:22:23 PM
B1-30
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Series Shaft
Size
Complete Unit Unit Without Adapter Adapter & Nut Assembly
Part No. Description Part No. Description Part No. Description
204 3/4 129291 TB-GTEZ-012-PCR 129537 TB-GTEZ-04-PCR 129967 AN-GT-04-012-CR
20mm 129292 TB-GTEZ-20M-PCR 129988 TB-GTEZ-04M-PCR 129980 AN-GT-04-20M-CR
205 1 129293 TB-GTEZ-100-PCR 129538 TB-GTEZ-05-PCR 129968 AN-GT-05-100-CR
25mm 129294 TB-GTEZ-25M-PCR 129989 TB-GTEZ-05M-PCR 129981 AN-GT-05-25M-CR
206
1 -1/8 @ TB-GTEZ-102-PCR 129969 AN-GT-06-102-CR
1 -3/16 129295 TB-GTEZ-103-PCR 129539 TB-GTEZ-06-PCR 129970 AN-GT-06-103-CR
1 -1/4 129296 TB-GTEZ-104S-PCR 129971 AN-GT-06-104S-CR
30mm 129297 TB-GTEZ-30M-PCR 129990 TB-GTEZ-06M-PCR 129982 AN-GT-06-30M-CR
207
1 -1/4 129298 TB-GTEZ-104-PCR 129972 AN-GT-07-104-CR
1 -3/8 @ TB-GTEZ-106-PCR 129540 TB-GTEZ-07-PCR 129973 AN-GT-07-106-CR
1 -7/16 129299 TB-GTEZ-107-PCR 129974 AN-GT-07-107-CR
35mm 129300 TB-GTEZ-35M-PCR 129991 TB-GTEZ-07M-PCR 129983 AN-GT-07-35M-CR
@ Assembled to order
ezkleen_sel_dim.indd B1-30 3/23/07 1:22:23 PM
B1-31
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Weight N R
Series Shaft Lbs A B C D J L M Thread Bolt Hole S# Z
Size kg Depth Threads
204 3/4 0.88 1-15/32 3-1/4 1-31/64 2 2-21/32 1-1/2 1-5/16 13/32 3/8-16 63/64 1-3/64
20 mm 0.41 37.3 82.6 37.7 50.8 67.6 38.1 33.3 10.2 M10x1.5 25.0 26.7
205 1 1.01 1-29/64 3-1/4 1-1/2 2 2-57/64 1-51/64 1-7/16 13/32 3/8-16 61/64 1-1/64
25 mm 0.47 36.9 82.6 37.7 50.8 73.3 45.6 36.5 10.2 M10x1.5 24.2 25.9
206
1-1/8 1.79 1-39/64 4-3/8 1-37/64 3 3-3/8 2-5/64 1-11/16 29/64 7/16-14 1-5/64 1-1/8
1-3/16 1.69
1-1/4 1.59
30 mm 0.77 40.9 111.1 40.1 76.2 85.9 52.8 42.9 11.4 M10x1.5 27.4 28.7
207
1-1/4 2.62 1-5/8 4-5/8 1-57/64 3-1/4 3-13/16 2-3/8 1-7/8 35/64 1/2-13 1-1/16 1-9/64
1-3/8 2.42
1-7/16 2.32
35 mm 1.11 41.3 117.5 48.0 82.6 97.2 60.3 47.6 14.0 M12x1.75 27.0 29.1
#S dimension will vary slightly depending on true shaft diameter
ezkleen_sel_dim.indd B1-31 3/23/07 1:22:24 PM
B1-32
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert With Flingers
Part No. Description Part No. Description
204
1/2 @ TB-SCEZ-008L-PCR* @ TB-SCEZ-008L-P
5/8 @ TB-SCEZ-010L-PCR* @ TB-SCEZ-010L-P
3/4 127509 TB-SCEZ-012-PCR @ TB-SCEZ-012-P
20 mm 127552 TB-SCEZ-20M-PCR @ TB-SCEZ-20M-P
205
7/8 @ TB-SCEZ-014-PCR* @ TB-SCEZ-014-P
15/16 @ TB-SCEZ-015-PCR* @ TB-SCEZ-015-P
1 127510 TB-SCEZ-100-PCR @ TB-SCEZ-100-P
25 mm 127553 TB-SCEZ-25M-PCR @ TB-SCEZ-25M-P
206
1-1/8 @ TB-SCEZ-102-PCR* @ TB-SCEZ-102-P
1-3/16 127511 TB-SCEZ-103-PCR @ TB-SCEZ-103-P
1-1/4 127512 TB-SCEZ-104S-PCR 058632 TB-SCEZ-104S-P
30 mm 127554 TB-SCEZ-30M-PCR @ TB-SCEZ-30M-P
207
1-1/4 127513 TB-SCEZ-104-PCR @ TB-SCEZ-104-P
1-5/16 @ TB-SCEZ-105-PCR* @ TB-SCEZ-105-P
1-3/8 056577 TB-SCEZ-106-PCR* @ TB-SCEZ-106-P
1-7/16 127514 TB-SCEZ-107-PCR @ TB-SCEZ-107-P
35 mm 127555 TB-SCEZ-35M-PCR @ TB-SCEZ-35M-P
@ Assembled to order
*20 piece minimum
ezkleen_sel_dim.indd B1-32 3/23/07 1:22:24 PM
B1-33
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Shaft
Size
Weight
lbs
kg
N
Thread
Depth
R
Bolt Hole
Threads
Series A B C D J L M S
204
1/2 0.74 1-5/32 3-1/4 1-31/64 2 2-21/32 1-1/8 1-5/16 13/32 3/8-16 47/64
5/8 0.66
3/4 0.60
20 mm 0.29 29.4 82.6 37.7 50.8 67.6 28.6 33.3 10.2 M10x1.5 18.7
205
7/8 0.72 1-3/16 3-1/4 1-1/2 2 2-57/64 1-21/64 1-7/16 13/32 3/8-16 49/64
15/16 0.64
1 0.58
25 mm 0.28 30.2 82.6 38.1 50.8 73.3 33.7 36.5 10.2 M10x1.5 19.4
206
1-1/8 1.16 1-25/64 4-3/8 1-37/64 3 3-3/8 1-37/64 1-11/16 29/64 7/16-14 29/32
1-3/16 1.09
1-1/4 1.07
30 mm 0.49 35.3 111.1 40.1 76.2 85.9 40.1 42.9 11.4 M10x1.5 23.0
207
1-1/4 1.64 1-17/32 4-5/8 1-57/64 3-1/4 3-13/16 1-27/32 1-7/8 35/64 1/2-13 1-1/32
1-5/16 1.58
1-3/8 1.53
1-7/16 1.48
35 mm 0.72 38.9 117.5 48.0 82.6 97.2 46.8 47.6 14.0 M12x1.75 26.2
E-Z KLEEN Mounted Bearings
SCEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
ezkleen_sel_dim.indd B1-33 3/23/07 1:22:24 PM
B1-34
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Series Shaft
Size
With Corrosion Resistant Insert Standard Insert With Flingers
Part No. Description Part No. Description
204 3/4 127587 TB-DLEZ-012-PCR @ TB-DLEZ-012-P
20 mm 127630 TB-DLEZ-20M-PCR @ TB-DLEZ-20M-P
205
7/8 @ TB-DLEZ-014-PCR* @ TB-DLEZ-014-P
15/16 @ TB-DLEZ-015-PCR* @ TB-DLEZ-015-P
1 127588 TB-DLEZ-100-PCR @ TB-DLEZ-100-P
25 mm 127631 TB-DLEZ-25M-PCR @ TB-DLEZ-25M-P
206
1-1/8 @ TB-DLEZ-102-PCR* @ TB-DLEZ-102-P
1-3/16 127589 TB-DLEZ-103-PCR @ TB-DLEZ-103-P
1-1/4 127590 TB-DLEZ-104S-PCR @ TB-DLEZ-104S-P
30 mm 127632 TB-DLEZ-30M-PCR @ TB-DLEZ-30M-P
207
1-1/4 127591 TB-DLEZ-104-PCR @ TB-DLEZ-104-P
1-3/8 @ TB-DLEZ-106-PCR* @ TB-DLEZ-106-P
1-7/16 127592 TB-DLEZ-107-PCR @ TB-DLEZ-107-P
35 mm 127633 TB-DLEZ-35M-PCR @ TB-DLEZ-35M-P
@ Assembled to order
*20 piece minimum
ezkleen_sel_dim.indd B1-34 3/23/07 1:22:25 PM
B1-35
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
DLEZ NORMAL DUTY POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Shaft
Size
Weight
lbs
kg
N
Thread
Depth
R
Bolt Hole
Threads
Series A B C D J L M S
204 3/4 0.88 1-9/32 3-1/4 1-31/64 2 2-21/32 1-45/64 1-5/16 13/32 3/8-16 25/32
20 mm 0.41 32.5 82.6 37.7 50.8 67.6 43.3 33.3 10.2 M10x1.5 19.8
205
7/8 1.12 1-7/16 3-1/4 1-1/2 2 2-57/64 2 1-7/16 13/32 3/8-16 7/8
15/16 1.11
1 1.01
25 mm 0.47 36.5 82.6 38.1 50.8 73.3 50.8 36.5 10.2 M10x1.5 22.2
206
1-1/8 1.79 1-9/16 4-3/8 1-37/64 3 3-3/8 2-7/32 1-11/16 29/64 7/16-14 15/16
1-3/16 1.69
1-1/4 1.59
30 mm 0.77 39.7 111.1 40.1 76.2 85.9 56.4 42.9 11.4 M10x1.5 23.8
207
1-1/4 2.62 1-3/4 4-5/8 1-57/64 3-1/4 3-13/16 2-11/16 1-7/8 35/64 1/2-13 1-1/16
1-3/8 2.42
1-7/16 2.32
35 mm 1.11 44.5 117.5 48.0 82.6 97.2 68.3 47.6 14.0 M12x1.75 27.0
ezkleen_sel_dim.indd B1-35 3/23/07 1:22:25 PM
B1-36
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
PSEZ POLYMER SLEEVE POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
Series Shaft
Size
Part
No. Description
204 3/4 034710 TB-PSEZ-012-P
20mm 034755 TB-PSEZ-20M-P*
205 1 034711 TB-PSEZ-100-P
25mm 034756 TB-PSEZ-25M-P*
206
1-3/16 034712 TB-PSEZ-103-P
1-1/4 034713 TB-PSEZ-104S-P
30mm 034757 TB-PSEZ-30M-P*
207
1-1/4 034714 TB-PSEZ-104-P
1-7/16 034715 TB-PSEZ-107-P
35mm 034758 TB-PSEZ-35M-P*
* Made to Order
ezkleen_sel_dim.indd B1-36 3/23/07 1:22:25 PM
B1-37
SELECTION/DIMENSIONS
Bearing Quick Reference E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
Series Shaft
Size
Weight
lbs
kg
N
Thread
Depth
R
Bolt Hole
Threads
ABCDJ LM
204 3/4 0.53 1 3-1/4 1-31/64 2 2-21/32 1-5/16 1-5/16 13/32 3/8-16
20mm 0.24 25.4 82.6 37.7 50.8 67.6 33.3 33.3 10.2 M10x1.5
205 1 0.46 1-1/16 3-1/4 1-1/2 2 2-57/64 1-7/16 1-7/16 13/32 3/8-16
25mm 0.21 27.0 82.6 38.1 50.8 73.3 36.5 36.5 10.2 M10x1.5
206
1-3/16 0.85 1-3/16 4-3/8 1-37/64 3 3-3/8 1-11/16 1-11/16 29/64 7/16-14
1-1/4 0.84
30mm 0.39 30.2 111.1 40.1 76.2 85.9 42.9 42.9 11.4 M10x1.5
207
1-1/4 1.02 1-5/16 4-5/8 1-57/64 3-1/4 3-13/16 2 1-7/8 35/64 1/2-13
1-7/16 0.97
35mm 0.46 33.3 117.5 48 82.6 96.8 50.8 47.6 14.0 M12x1.75
* Made to order
E-Z KLEEN Mounted Bearings
PSEZ POLYMER SLEEVE POLYMER HOUSED TAPPED BASE PILLOW BLOCKS
ezkleen_sel_dim.indd B1-37 3/23/07 1:22:26 PM
B1-38
Bearing Quick Reference
SELECTIONS/DIMENSIONS
E-Z KLEEN GRIP TIGHT Adapter Ball Bearing Set Screw Ball Bearing Eccentric Collar Ball Bearing
FEATURES/BENEFITS
PAGE B1-2
SELECTION
PAGE B1-5
INTERCHANGE
PAGE B1-88
ACCESSORIES
PAGE B1-90
E-Z KLEEN Mounted Bearings
GTEZ NORMAL DUTY POLYMER HOUSED 2 BOLT FLANGE BEARINGS
Series Shaft
Size
Complete Unit Unit Without Adapter Adapter & Nut Assembly
Part No. Description Part No. Description Part No. Description
204 3/4 129339 F2B-GTEZ-012-PCR 129548 F2B-GTEZ-04-PCR 129967 AN-GT-04-012-CR
20mm 129340 F2B-GTEZ-20M-PCR 129980 AN-GT-04-20M-CR
205 1 129341 F2B-GTEZ-100-PCR 129549 F2B-GTEZ-05-PCR 129968 AN-GT-05-100-CR
25mm 129342 F2B-GTEZ-25M-PCR 129981 AN-GT-05-25M-CR
206
1 -1/8 @ F2B-GTEZ-102-PCR
129550 F2B-GTEZ-06-PCR
129969 AN-GT-06-102-CR
1 -3/16 129343 F2B-GTEZ-103-PCR 129970 AN-GT-06-103-CR
1 -1/4 129344 F2B-GTEZ-104S-PCR 129971 AN-GT-06-104S-CR
30mm 129345 F2B-GTEZ-30M-PCR 129982 AN-GT-06-30M-CR
207
1 -1/4 129346 F2B-GTEZ-104-PCR
129551 F2B-GTEZ-07-PCR
129972 AN-GT-07-104-CR
1 -3/8 @ F2B-GTEZ-106-PCR 129973 AN-GT-07-106-CR
1 -7/16 129347 F2B-GTEZ-107-PCR 129974 AN-GT-07-107-CR
35mm 129348 F2B-GTEZ-35M-PCR 129983 AN-GT-07-35M-CR
208 1 -1/2 129349 F2B-GTEZ-108-PCR 129552 F2B-GTEZ-08-PCR 129975 AN-GT-08-108-CR
40mm 129350 F2B-GTEZ-40M-PCR 129984 AN-GT-08-40M-CR
209
1-11/16 129351 F2B-GTEZ-111-PCR
129553 F2B-GTEZ-09-PCR
129976 AN-GT-09-111-CR
1 -3/4 064147 F2B-GTEZ-112-PCR 129977 AN-GT-09-112-CR
45mm 129352 F2B-GTEZ-45M-PCR 129985 AN-GT-09-45M-CR
210
1-15/16 129353 F2B-GTEZ-115-PCR
129554 F2B-GTEZ-10-PCR
129978 AN-GT-10-115-CR
2 064503 F2B-GTEZ-200-PCR 129979 AN-GT-10-200-CR
50mm 129354 F2B-GTEZ-50M-PCR 129986 AN-GT-10-50M-CR
@ Assembled to order
ezkleen_sel_dim.indd B1-38 3/23/07 1:22:26 PM
