该页无缩略图
可转位铣削产品一览表
| 类型 | 应用 | 刀片系列 | 刀体系列 | 图示 | 简介 |
 $\begin{array} { r } { { \mathsf { R D 0 7 : A P M } } = 3 . 5 ~ { \mathsf { m m } } } \\ { { \mathsf { R D 1 0 : A P M } } \times = 5 . 0 ~ { \mathsf { m m } } } \end{array}$ | RD P052 | MPA100 (Φ16-Φ50) |  | 钢、合金钢材 料的仿形、平 面、槽铣及型 腔铣削加工。 | |
| 仿形 铣削 |  $\mathsf { R P 1 0 : A P M X } = 5 . 0 \mathsf { m m }$ | RP P052 | MPB100 (Φ20-Φ50) |  | 钢、合金钢材 料的仿形、平 面、槽铣及型 腔铣削加工。 |
 | RC10: APMX =5.0 mm RC12: APMX =6.0 mm | RC P052 | MPC100 (Φ20-Φ80) |  | 钢、合金钢材 料的仿形、平 面、槽铣及型 腔铣削加工。 |
平面铣削
SEET正型四刃平面铣刀片
订货号SEET1204AFEN-PL  | 尺寸(mm) | 金属陶瓷 | ||||||
| LE | IC | S | D1 | RE | BS | GP01TM | ||
| 8.2 | 12.7 | 4.76 | 5.5 | 1.2 | 1.6 | |||
| SEET13T3AGEN-PM | 8.8 | 13.4 | 3.97 | 4.4 | 1.5 | 1.2 | ||
●标准库存需预定
SEEN/SEMN 正型四刃平面铣刀片
订货号SEEN1203AFTNSEMN1203AFTN SEEN1203AFEN | 尺寸(mm) | 金属陶瓷 | |||
| LE | IC | S | BS | GP01TM | |
| 8.8 | 12.7 | 3.18 | 2.3 | ||
| 8.8 | 12.7 | 4.76 | 2.4 | O | |
| 8.8 | 12.7 | 3.18 | 2.3 | ||
●标准库存需预定
APMT正型两刃方肩铣刀片
方肩铣削
| 订货号 | 尺寸(mm) | 金属陶瓷 | ||||||
| LE | W1 | S | BS | D1 | RE | GP01TM | ||
APMT1135PDER-PM | 9.7 | 6.16 | 3.5 | 1.92 | 2.8 | 0.8 | ||
| APMT1604PDER-PM | 14.9 | 9.26 | 4.76 | 2 | 4.6 | 0.8 | ||
| APMT113504R-PM | 9.7 | 6.16 | 3.5 | 1.92 | 2.8 | 0.4 | ||
●标准库存需预定
仿形铣削
RD正型仿形铣刀片
| 订货号 | 尺寸(mm) | 金属陶瓷 | ||||
| IC | S | RE | D1 | GP01TM | ||
RDEW0702M0 | 7 | 2.38 | 3.5 | 2.8 | ● | |
| 10 | 3.97 | 5 | 4.4 | O | ||
●标准库存需预定
RP正型仿形铣刀片
| 订货号 | ||||||
| 尺寸(mm) | 金属陶瓷 | |||||
| IC | S | RE | D1 | GP01TM | ||
RPMW1003M0T | 10 | 3.18 | 5 | 4.4 | ||
●标准库存需预定
RC正型仿形铣刀片
| 订货号 | ||||||
| 尺寸(mm) | 金属陶瓷 | |||||
| IC | S | RE | D1 | GP01TM | ||
 | RCET10T3M0-EM | 10 | 3.97 | 5 | 4.4 | O |
 | RCET1204M0-MM | 12 | 4.76 | 6 | 4 | O |
●标准库存需预定
推荐切削参数
SEET/SEEN
| 被加工材料 | 材料硬度 | 牌号 | 规格 | 推荐切深ap(mm) | 切削速度Vc(m/min) | 进给/刃fz(mm) | ||
| 轻切削 (L) | 中切削 (M) | |||||||
 | 软钢 | ≤HB180 | GP01TM | SEET13T3 | 2 | 250(210-290) | 0.20(0.10-0.30) | 0.25(0.15-0.35) |
| SEET1204 | ||||||||
| SEEN1203 | ||||||||
| 碳钢、合金钢 | HB180-350 | GP01TM | SEET13T3 | 2 | 220(180-260) | 0.15(0.10-0.20) | 0.25(0.15-0.35) | |
| SEET1204 | ||||||||
| SEEN1203 | ||||||||
| 预硬钢 | HRC35-45 | GP01TM | SEET13T3 | 2 | 140(100-180) | 0.10(0.05-0.15) | 0.15(0.10-0.20) | |
| SEET1204 | ||||||||
| SEEN1203 | ||||||||
APMT
| 被加工材料 | 材料硬度 | 牌号 | 规格 | 推荐切深ap(mm) | 切削速度Vc(m/min) | 进给/刃fz(mm) | |
| 中切削 (M) | |||||||
| P | 软钢 | ≤HB180 | GP01TM | APMT1135 | 2.7 | 250(210-290) | 0.15(0.10-0.20) |
| APMT1604 | 4.2 | 0.25(0.15-0.35) | |||||
| 碳钢、合金钢 | HB180-350 | GP01TM | APMT1135 | 2.7 | 220(180-260) | 0.15(0.10-0.20) | |
| APMT1604 | 4.2 | 0.25(0.15-0.35) | |||||
| 预硬钢 | HRC35-45 | GP01TM | APMT1135 | 2.7 | 140 | 0.10(0.05-0.15) | |
| APMT1604 | 4.2 | (100-180) | 0.15(0.10-0.20) | ||||
推荐切削参数
RD/RP/RC
| 被加工材料 | 材料硬度 | 牌号 | 切削速度Vc(m/min) | 刀片规格 | 进给/刃fz(mm) | ||
| 中切削 (M) | 重切削 (H) | ||||||
| P | 软钢 | ≤HB180 | GP01TM | 180(140-220) | 07 | 0.12(0.08-0.18) | 0.15(0.10-0.25) |
| 1012 | 0.20(0.15-0.30) | 0.25(0.20-0.35) | |||||
| 碳钢、合金钢 | HB180-350 | GP01TM | 160(120-200) | 07 | 0.12(0.08-0.18) | 0.15(0.10-0.25) | |
| 1012 | 0.20(0.15-0.30) | 0.25(0.20-0.35) | |||||
| 预硬钢 | HRC35-45 | GP01TM | 120(80-160) | 07 | 0.12(0.08-0.18) | 0.15(0.10-0.25) | |
| 1012 | 0.20(0.15-0.30) | 0.25(0.20-0.35) | |||||
PCBN刀具
PCBN刀具概述
CBN材料硬度仅次于金刚石材料，不易与铁系金属发生反应，其具有极高的硬度、耐热性及导热性，特别适合铸铁、淬火钢、铁基粉末冶金等材料的高精高效加工，并且能够实现稳定的尺寸精度、表面质量及更长的刀具寿命。
·高硬材料选用推荐
1.红硬性好，金属去除率高；
2.具有更高的尺寸精度;
2.具有更高的尺寸精度;
·灰铸铁材料加工推荐切削参数
产品系列
| 一代产品YZ系列及YS系列均以S结尾，二代产品拆分成Z及S。 | P | 焊片式YP系列 | ||||
| B | H | C | 2 | 25 | Z | 立柱式YZ系列 |
| S | 整体式YS系列 | |||||
| 产品系列 | 加工类型 | 装夹 | 应用行业 | 被加工材料 | |
| 焊片式PCBNYP系列 |  | 超精、精加工ap:0.05~0.5mm |  定位孔M/D | 汽车：制动盘、齿轮、球笼、轮毂轴承单元通用机械：减速机齿轮、轴承 | K铸铁：灰铸铁、球墨铸铁H高硬材料：淬火钢、表面堆焊材料S难加工材料：粉末冶金 |
| 立柱式PCBNYZ系列 |  | 精、半精加工ap:0.05~0.8mm定位孔M/D |  定位孔M/D | 汽车：制动盘、制动鼓、齿轮、曲轴通用机械：空调压缩机、减速机齿轮、轴承 | K铸铁：灰铸铁H高硬材料：淬火钢、表面堆焊材料 |
| 整体式PCBNYS系列 |  | 精、半精、粗加工  ap: 0.1~1/3Lmm压板式C | 汽车：制动盘、制动鼓、变速箱壳体、发动机缸体及缸盖通用机械：减速机齿轮、轴承能源重工：轧辊、渣浆泵、轧臼壁、矿山机械、回转支撑 | K铸铁：灰铸铁H高硬材料：淬火钢、高镍铬、高硬度合金铸铁、铸造高速钢、高锰钢、表面堆焊材料 | |
刀具材质
淬火钢加工
推荐切削参数
| ISO | H | 被加工材料 | 高硬度材料 | 硬度 | ≥HRC50 | |
| 产品系列 | 用途 | 牌号 | 切削范围 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||
| 焊片式 | 连续~轻断续 | BHC210P | 精加工 | 140-180-260 | 0.05-0.10-0.20 | 0.05-0.08-0.15 |
| 半精加工 | 100-150-180 | 0.10-0.20-0.35 | 0.08-0.12-0.25 | |||
| BHC115P | 精加工 | 100-160-200 | 0.05-0.10-0.20 | 0.05-0.08-0.15 | ||
| 半精加工 | 70-140-160 | 0.10-0.20-0.35 | 0.08-0.12-0.25 | |||
| 轻~中等断续 | BHC225P | 精加工 | 120-160-220 | 0.05-0.10-0.20 | 0.05-0.08-0.15 | |
| 半精加工 | 100-140-170 | 0.10-0.20-0.35 | 0.08-0.13-0.25 | |||
| 粗加工 | 100-120-140 | 0.25-0.35-0.50 | 0.10-0.20-0.25 | |||
| BHC125P | 精加工 | 120-150-180 | 0.05-0.10-0.50 | 0.05-0.10-0.20 | ||
| 半精加工 | 100-120-180 | 0.10-0.20-0.35 | 0.08-0.13-0.25 | |||
| 粗加工 | 60-110-140 | 0.25-0.35-0.50 | 0.10-0.20-0.25 | |||
| 强断续 | BHC135P | 精加工 | 80-120-150 | 0.05-0.10-0.20 | 0.05-0.08-0.15 | |
| 半精加工 | 60-100-130 | 0.10-0.25-0.35 | 0.08-0.13-0.25 | |||
| 立柱式 | 连续~轻断续 | BHC215Z | 精加工 | 120-150-230 | 0.05-0.10-0.20 | 0.05-0.10-0.15 |
| 半精加工 | 100-120-180 | 0.10-0.30-0.50 | 0.08-0.15-0.25 | |||
| 轻~中等断续 | BHC225Z | 精加工 | 120-150-200 | 0.05-0.10-0.20 | 0.05-0.10-0.15 | |
| 半精加工 | 100-130-180 | 0.10-0.30-0.35 | 0.08-0.15-0.25 | |||
| 粗加工 | 80-110-150 | 0.25-0.50-0.80 | 0.10-0.20-0.30 | |||
| 整体式 | 轻~中等断续 | BHN225S | 精加工 | 120-150-190 | 0.05-0.20-0.35 | 0.05-0.10-0.20 |
| 半精加工 | 100-130-160 | 0.10-0.50-2.00 | 0.08-0.20-0.35 | |||
| 粗加工 | 70-100-130 | 0.25-1.00-1/3L | 0.10-0.35-0.50 | |||
刀具材质
铸铁加工
· 焊片式牌号推荐
典型零件
推荐切削参数
| ISO | K | 被加工材料 | 铸铁材料 | 硬度 | HB180~300 | |
| 产品系列 | 用途 | 牌号 | 切削范围 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||
| 焊片式 | 连续~断续(灰铸铁) | BKN115P | 精加工 | 600-800-1500 | 0.05-0.10-0.30 | 0.05-0.10-0.20 |
| 半精加工 | 400-600-1000 | 0.15-0.25-0.50 | 0.05-0.20-0.40 | |||
| 连续~断续(球墨铸铁) | BKC120P | 精加工 | 250-350-500 | 0.10-0.10-0.50 | 0.05-0.10-0.30 | |
| 半精加工 | 150-250-400 | 0.15-0.25-0.50 | 0.05-0.20-0.40 | |||
| 立柱式 | 连续~断续(灰铸铁) | BKN225Z | 精加工 | 600-800-1200 | 0.05-0.10-0.30 | 0.05-0.10-0.20 |
| 半精加工 | 400-600-1000 | 0.15-0.30-0.50 | 0.05-0.20-0.40 | |||
| 粗加工 | 300-450-700 | 0.30-0.50-0.80 | 0.05-0.25-0.40 | |||
| 整体式 | 连续~断续(灰铸铁) | BKN225S | 精加工 | 600-800-1200 | 0.05-0.20-0.50 | 0.05-0.10-0.20 |
| 半精加工 | 400-600-1000 | 0.05-0.50-1.00 | 0.05-0.20-0.50 | |||
| 粗加工 | 300-450-700 | 0.05-2.00-1/3L | 0.05-0.25-0.50 | |||
刀具材质
粉末冶金加工
· 焊片式牌号推荐
典型零件
推荐切削参数
| ISO | S | 被加工材料 | 粉末冶金 | 硬度 | HRB50~90 | |
| 产品系列 | 用途 | 牌号 | 切削范围 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||
| 焊片式 | 连续~断续 | BSN115P | 精加工 | 100-200-300 | 0.05-0.10-0.25 | 0.05-0.10-0.30 |
| 半精加工 | 50-140-200 | 0.05-0.25-0.50 | 0.05-0.15-0.30 | |||
刃口形式介绍
· 金鹭刃口形式选用推荐
| 切削阻力 | 刃口形式 | 说明 | 处理形式 | 推荐切深ap(mm) | 适用断续程度 | 刃口强度 |
| 小大 | LE | 保证尺寸精度、表面粗糙度 | 钝化 | ~0.15 | 连续 | 低1高 |
| LT | 保证尺寸精度、毛刺 | 倒棱 | ~0.15 | 连续 | ||
| L | 主要用于正型刀片，连续加工，提升耐磨性 | 倒棱+钝化 | 0.10~0.25 | 连续~轻断续 | ||
| LS | 主要用于负型刀片，连续加工，提升耐磨性 | 倒棱+钝化 | 0.10~0.25 | 连续~轻断续 | ||
| M | 通用型刃口 | 倒棱+钝化 | 0.12~0.35 | 轻~中等断续 | ||
| H | 断续加工，提升抗崩性 | 倒棱+钝化 | 0.15~0.50 | 断续~强断续 |
淬火钢加工
铸铁、粉末冶金加工
车削刀片型号表示规则
| 代号 | 形状 | 刀尖(度) | 图形 | |
| H | 正六边形 | 120° | ||
| 0 | 正八边形 | 135° | ||
| P | 正五边形 | 108° | ||
| S | 正方形 | 90° | ||
| T | 正三角形 | 60° | ||
| C | 80° | |||
| D | 菱形 | 55°35° | ||
| V | ||||
| W | 六边形 | 80° | ||
| L | 长方形 | 90° | ||
| A | 平行四边形 | 85° | ||
| R | 圆形 | -- | O | |
①形状代号
| 代号 | 后角(度) |
| A | 3° |
| B | 5° |
| C | 7° |
| D | 15° |
| E | 20° |
| F | 25° |
| G | 30° |
| N | 0° |
| P | 11° |
| 0 | 其他 |
②后角代号
| 代号(级) | 公差(毫米) | 公差(毫米) | ||||
| 刀尖高 | 厚度 | 内切圆(∅d) | 刀尖高 | 厚度 | 内切圆(∅d) | |
| A | ±0.005 | ±0.025 | ±0.025 | ±0.0002 | ±0.001 | ±0.001 |
| F | ±0.005 | ±0.025 | ±0.013 | ±0.0002 | ±0.001 | ±0.0005 |
| C | ±0.013 | ±0.025 | ±0.025 | ±0.0005 | ±0.001 | ±0.001 |
| H | ±0.013 | ±0.025 | ±0.013 | ±0.0005 | ±0.001 | ±0.0005 |
| E | ±0.025 | ±0.025 | ±0.025 | ±0.001 | ±0.001 | ±0.001 |
| G | ±0.025 | ±0.13 | ±0.025 | ±0.001 | ±0.005 | ±0.001 |
| J | ±0.005 | ±0.025 | ±0.05~0.13 | ±0.0002 | ±0.001 | ±0.002~0.005 |
| K | ±0.013 | ±0.025 | ±0.05~0.13 | ±0.0005 | ±0.001 | ±0.002~0.005 |
| L | ±0.025 | ±0.025 | ±0.05~0.13 | ±0.001 | ±0.001 | ±0.002~0.005 |
| M | ±0.08~0.18 | ±0.13 | ±0.05~0.13 | ±0.003~0.007 | ±0.005 | ±0.002~0.005 |
| N | ±0.08~0.18 | ±0.025 | ±0.05~0.13 | ±0.003~0.007 | ±0.001 | ±0.002~0.005 |
| U | ±0.13~0.38 | ±0.13 | ±0.08~0.25 | ±0.005~0.015 | ±0.005 | ±0.003~0.01 |
③精度代号
C
T
[①]
C
N
②
G
G
A
④
09
16
⑤
| ④断屑槽·孔代号 | ||||
| 代号 | 有无孔 | 孔的形状 | 断屑槽 | 形状 |
| N | 无 | 无 | ||
| R | 单面 | |||
| F | 双面 | |||
| A | 圆柱孔 | 无 | 日日 | |
| M | 单面 | |||
| G | 双面 | |||
| W | 部分圆柱孔单面40°~60° | 无 | ||
| T | 单面 | |||
| Q | 有 | 部分圆柱孔双面40°~60° | 无 | |
| U | 双面 | |||
| B | 部分圆柱孔单面70°~90° | 无 | ||
| H | 单面 | |||
| C | 部分圆柱孔双面70°~90° | 无 | ||
| J | 双面 | |||
| X | 1 | 一 | ||
⑤ISO切削刃长度代号 (mm)
| T 1 | SYY | CT 1 | 1 | D | K | 内切圆(mm) | ||||||||||
| 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | |
| 03 | 3.97 | 03 | 4.0 | 06 | 6.9 | 4 | 4.8 | 3.97 | ||||||||
| 04 | 4.76 | 04 | 4.8 | 08 | 8.2 | 5 | 5.8 | 4.76 | ||||||||
| 05 | 5 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 5 |
| 05 | 5.56 | 05 | 5.6 | 03 | 3.8 | 09 | 9.6 | 6 | 6.8 | 5.56 | ||||||
| 06 | 6 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 6 |
| 06 | 6.35 | 06 | 6.5 | 04 | 4.3 | 11 | 11 | 7 | 7.8 | 11 | 11.2 | 6.35 | ||||
| 07 | 7.94 | 08 | 8.1 | 05 | 5.4 | 13 | 13.8 | 9 | 9.7 | 7.94 | ||||||
| 08 | 8 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 8 |
| 09 | 9.525 | 09 | 9.525 | 09 | 9.7 | 06 | 6.5 | 16 | 16.5 | 11 | 11.6 | 16 | 16.6 | 16 | 19.7 | 9.525 |
| 10 | 10 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 10 |
| 12 | 12 | -- | -= | -- | -- | =- | -- | -- | =- | -- | =- | =- | -- | -= | -- | 12 |
| 12 | 12.7 | 12 | 12.7 | 12 | 12.9 | 08 | 8.7 | 22 | 22 | 15 | 15.5 | 22 | 22.1 | 12.7 | ||
| 15 | 15.875 | 15 | 15.875 | 16 | 16.1 | 10 | 10.9 | 27 | 27.5 | 19 | 19.4 | 15.875 | ||||
| 16 | 16 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 16 |
| 19 | 19.05 | 19 | 19.05 | 19 | 19.3 | 13 | 13 | 33 | 33 | 23 | 23.3 | 19.05 | ||||
| 20 | 20 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 20 |
| 22 | 22.225 | 22 | 22.6 | 38 | 38.5 | 27 | 27.1 | 22.225 | ||||||||
| 25 | 25 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 25 |
| 25 | 25.4 | 25 | 25.4 | 25 | 25.8 | 44 | 44 | 31 | 31 | 25.4 | ||||||
| 31 | 31.75 | 31 | 31.75 | 32 | 32.2 | 55 | 55 | 38 | 38.8 | 31.75 | ||||||
| 31 | 32 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 32 |
车削刀片型号表示规则
⑨可转位次数<br>⑥厚度代号
| 代号 | 前角 (度) |
| GN | 0°（通用型) |
| GB | 5°（通用型） |
| KB | 5°（高光型) |
⑧刃口形式代码PCD刀片
0
T3
04
04
GB
1
08
M
3
0]
8
0
| 代号 | 厚度 |
| 01 | 1.59 |
| 02 | 2.38 |
| T2 | 2.78 |
| 03 | 3.18 |
| T3 | 3.97 |
| 04 | 4.76 |
| 05 | 5.56 |
| 06 | 6.35 |
| 07 | 7.94 |
| 09 | 9.52 |
⑦刀尖代号
| 代号 | 刀尖圆弧半径 |
| 00 | 0.03 |
| 02 | 0.2 |
| 04 | 0.4 |
| 08 | 0.8 |
| 12 | 1.2 |
| 16 | 1.6 |
| 20 | 2.0 |
| 24 | 2.4 |
| 28 | 2.8 |
| 32 | 3.2 |
⑧刃口形式代码PCBN刀片
| 代号 | 刃口形式 |
| L | 连续标准型 |
| LS | 连续补充型 |
| M | 连续通用型 |
| H | 断续强化型 |
| 代号 | 可转位次数 |
| 1 | 1 |
| 2 | 2 |
| 3 | 3 |
| 4 | 4 |
| 6 | 6 |
车削刀片一览表
| 形式 | 特点 | 菱形80° | 菱形55° | 三角形60° | 菱形35° | 六边形80° | 四边形90° | 圆形360° | |
| 焊片式 | · 用于更高精度、更长寿命的切削；·刀具形式多样化。 | 负型PCBN |  |  |  |  |  | ||
| CNGA | DNGA | TNGA | VNGA | WNGA | |||||
| P067 | P068 | P069 | P070 | P070 | |||||
| 正型PCBN |  |  |  |  | |||||
| CCGW | DCGW | TCGW/TPGW | VBGW/VCGW | ||||||
| P071 | P071 | P072 | P073 | ||||||
| 立柱式 | · 双面可用，经济性更高；· 具有牢固的焊接稳定性。 | 负型PCBN |  |  |  |  |  | ||
| CNGA | DNGA | TNGA | VNGA | WNGA | |||||
| P074 | P074 | P075 | P075 | P076 | |||||
| 整体式 | • 整体式结构，能够实现大余量或者不稳定工况的加工。 | 负型PCBN |  |  |  |  |  | ||
| CNGN | DNGN | WNGN | SNGN | RNGN | |||||
| P077 | P077 | P078 | P078 | P079 | |||||
| 正型PCBN |  | ||||||||
| RCGN | |||||||||
| P079 |
PCBN车削刀片(负型)
菱形80°有孔
订货号CNGA120404LS-2 2 | |||||||||||||||
| 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||||
| LE | IC | S | D1 | RE | BKN15P | BSN15P | BKC0P | BHC15P | BHC25P | BH35P | BHC20P | BHC225P | |||
| 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | ● | ● | ● | ● | ||||||
| CNGA120408LS-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | O | ● | |||||||
| CNGA120404M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | O | O | ● | ● | ● | ||||
| CNGA120408M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | O | O | O | ● | ● | ● | ● | |||
| CNGA120412M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | ● | ● | ● | |||||||
| CNGA120408H-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● | |||||||
| CNGA120404LS-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ||||||||||
| CNGA120408LS-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||
| CNGA120404M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | |||||||||
| CNGA120408M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||
| CNGA120412M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | ● | |||||||||
| CNGA120408H-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||
●标准库存需预定
PCBN车削刀片(负型)
| 订货号DNGA150404LS-2 2 | |||||||||||||||||
| 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||||||
| LE | IC | S | D1 | RE | BKN15P | BSN115P | BK220P | BHC15P | BH25P | BHC35P | BH20P | BHC25P | |||||
| 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | ● | O | ||||||||||
| DNGA150408LS-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||||
| DNGA150404M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | O | ● | ● | ||||||||
| DNGA150408M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● | ● | ● | ● | ||||||
| DNGA150412M-2 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | ● | ● | ||||||||
| DNGA150608M-2 | 2.2 | 12.7 | 6.35 | 5.16 | 0.8 | O | O | ||||||||||
| DNGA150612M-2 | 2.2 | 12.7 | 6.35 | 5.16 | 1.2 | O | O | O | |||||||||
| DNGA150404LS-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | |||||||||||
| DNGA150408LS-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||||
| DNGA150404M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | |||||||||||
| DNGA150408M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | |||||||||||
| DNGA150412M-4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | ● | |||||||||||
| DNGA150604M-4 | 2.2 | 12.7 | 6.35 | 5.16 | 0.4 | ● | |||||||||||
| DNGA150608M-4 | 2.2 | 12.7 | 6.35 | 5.16 | 0.8 | ● | |||||||||||
| DNGA150612M-4 | 2.2 | 12.7 | 6.355.16 1.2 | ||||||||||||||
●标准库存需预定
PCBN车削刀片(负型)
订货号 | |||||||||||||||
| 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||||||||
| LE | IC | S | D1 | RE | BKNN15P | BSN15P | BKC0P | BHC15P | BHC25P | BHC35 | BH0P | BHC25P | |||
| TNGA160404LS-3 | 3 | 2.29.525 | 4.76 | 3.81 | 0.4 | ● | |||||||||
| TNGA160408LS-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ● | |||||||
| TNGA160404M-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ● | ● | ● | ● | ● | ● | ||
| TNGA160408M-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | O | ● | ● | ● | ● | ● | |||
| TNGA160412M-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | O | O | O | ||||||
| TNGA160404H-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ||||||||
| TNGA160408H-3 | 3 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | O | O | ● | ||||||
| TNGA160404LS-6 | 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||||||
| TNGA160408LS-6 | 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ||||||||
| TNGA160404M-6 | 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||||||
| TNGA160408M-6 | 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ||||||||
| TNGA160412M-6 | 6 | 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | ● | ||||||||
| TNGA160408H-6 | 6 | 2.29.525 | 4.76 | 3.81 0.8 | |||||||||||
●标准库存需预定
PCBN车削刀片(负型)
订货号 | |||||||||||||||
| 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||||||||
| LE | IC | S | D1 | RE | BKNN15P | BSN115P | BKCC20P | BHCC15P | BHC25P | BHC35P | BHC0P | BH25P | |||
| 2 | 2.29.525 | 4.76 | 3.81 | 0.4 | ● | ● | |||||||||
| VNGA160408LS-2 | 2 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | O | ● | |||||||
| VNGA160404M-2 | 2 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ● | ● | ● | ● | ||||
| VNGA160408M-2 | 2 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ● | O | ● | |||||
| VNGA160412M-2 | 2 | 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | ● | ● | |||||||
| VNGA160404LS-4 | 4 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||||||
| VNGA160408LS-4 | 4 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ||||||||
| VNGA160404M-4 | 4 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||||||
| VNGA160408M-4 | 4 | 2.2 9.525 | 4.76 | 3.81 | 0.8 | ● | |||||||||
| VNGA160412M-4 | 4 | 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | ● | ||||||||
●标准库存需预定
订货号 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN15P | BKC0P | BHCC15P | BHC25 | BHC35P | BHC20P | BH225P | |||
| WNGA080404LS-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | ● | |||||||
| WNGA080408LS-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | C | ● | |||||||
| WNGA080404M-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | ● | |||||||
| WNGA080408M-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | O | O | ● | ● | ● | |||
| WNGA080412M-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | ● | O | ||||||
| WNGA080408H-3 | 3 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● | ||||||
| WNGA080404LS-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | ||||||||
| WNGA080408LS-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ||||||||
| WNGA080404M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | ||||||||
| WNGA080408M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ||||||||
| WNGA080412M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | |||||||||
| ● | |||||||||||||||
●标准库存需预定
菱形80°有孔
订货号CCGW060202L-2 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN15P | BKC0P | BHCC15P | BH25P | BHC35P | BH0P | BHC25P | |||
| 2 | 2 | 6.35 | 2.38 | 2.8 | 0.2 | O | ● | ● | |||||||
| CCGW060204L-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.4 | O | ● | ● | ● | ● | ||||
| CCGW060208L-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.8 | O | O | O | ||||||
| CCGW060204M-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ● | ● | ||||||
| CCGW060208M-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ● | ● | ||||||
| CCGW09T304L-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ● | ● | ● | |||||
| CCGW09T308L-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.8 | O | O | O | ||||||
| CCGW09T304M-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | O | O | ● | ● | ● | ● | ||
| CCGW09T308M-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.8 | ● | O | O | ● | ● | ● | ● | ||
| CCGW09T304H-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||
| CCGW09T308H-2 | 2 | 2 | 9.525 | 3.97 | 4.4 0.8 O | ||||||||||
●标准库存需预定
菱形55°有孔
| 订货号DCGW070202L-2 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||
| LE | IC | S | D1 | RE | BKN15P | BSN15P | BKC20P | BHCC15P | BHC25P | BHCC35P | BH20P | BHC25P | |||
| 2 | 2 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ● | ● | |||||||
| DCGW070204L-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.4 | O | O | ● | ● | ● | ||||
| DCGW070204M-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.4 | O | O | |||||||
| DCGW070208M-2 | 2 | 2 | 6.35 | 2.38 | 2.8 | 0.8 | O | ● | |||||||
 | DCGW11T304L-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | O | O | ● | |||||
| DCGW11T308L-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.8 | O | O | ● | ||||||
| DCGW11T302M-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||
| DCGW11T304M-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ● | ● | ||||||
| DCGW11T308M-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ● | ● | ● | ● | ||||
●标准库存需预定
PCBN车削刀片(正型)
三角形60°有孔
| 订货号 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN15P | BKC220P | BHC15P | BHCC25P | BHC35P | BHC20P | BHC25P | |||
TCGW110304L-3TCGW110304M-3 TCGW110308M-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.4 | O | O | |||||||
| 3 | 2 | 6.35 | 3.18 | 3.4 | 0.4 | ● | O | ||||||||
| 3 | 2 | 6.35 | 3.18 | 3.4 | 0.8 | O | O | ||||||||
●标准库存需预定
三角形60°有孔
订货号 | |||||||||||||||
| 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN15P | BKC220P | BHCC15P | BH25 | BHC35P | BH220P | BHC225P | |||
| TPGW080202L-1 | 1 | 2 | 4.76 | 2.38 | 2.34 | 0.2 | ● | O | O | ||||||
| TPGW080204L-1 | 1 | 2 | 4.76 | 2.38 | 2.34 | 0.4 | ● | ● | |||||||
| TPGW080208L-1 | 1 | 2 | 4.76 | 2.38 | 2.34 | 0.8 | O | O | |||||||
| TPGW090202L-3 | 3 | 2 | 5.56 | 2.38 | 2.8 | 0.2 | O | O | O | ||||||
| TPGW090204L-3 | 3 | 2 | 5.56 | 2.38 | 2.8 | 0.4 | ● | O | O | ● | ● | ||||
| TPGW090208L-3 | 3 | 2 | 5.56 | 2.38 | 2.8 | 0.8 | O | O | |||||||
| TPGW110204L-3 | 3 | 2 | 6.35 | 2.38 | 2.8 | 0.4 | ● | O | O | ||||||
| TPGW110208M-3 | 3 | 2 | 6.35 | 2.38 | 2.8 | 0.8 | O | ||||||||
| TPGW110302L-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.2 | O | ||||||||
| TPGW110304L-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.4 | ● | ● | O | ● | ● | ● | ● | ||
| TPGW110308L-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.8 | ● | ● | ● | ● | |||||
| TPGW110304M-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.4 | O | O | O | ||||||
| TPGW110308M-3 | 3 | 2 | 6.35 | 3.18 | 3.4 | 0.8 | O | O | |||||||
●标准库存需预定
订货号 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN15P | BKC20P | BHC15P | BH25 | BHC35P | BHC20P | BHC225P | |||
| VBGW110302L-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.2 | O | O | O | O | |||||
| VBGW110304L-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | O | ● | O | |||||
| VBGW110308L-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.8 | O | O | O | ||||||
| VBGW110304M-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.4 | O | ● | |||||||
| VBGW110308M-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.8 | O | O | |||||||
| VBGW160404L-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.4 | O | O | ● | ||||||
| VBGW160408L-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.8 | O | O | O | ||||||
| VBGW160404M-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.4 | O | ● | O | ● | |||||
| VBGW160408M-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.8 | ● | O | ● | ● | ● | ||||
| CCGW09T304H-2 | 2 | 2 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||
| CCGW09T308H-2 | 2 | 2 9.525 | 3.97 4.4 0.8 | ||||||||||||
●标准库存需预定
订货号VCGW110302L-2 | |||||||||||||||
| 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||||||||
| LE | IC | S | D1 | RE | BKNN115P | BSN115P | BKCC20P | BHC15P | BHCC25 | BHC35P | BH20P | BH225P | |||
| 2 | 2 | 6.35 | 3.18 | 2.8 | 0.2 | O | O | ||||||||
| VCGW110304L-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | O | ● | ||||||
| VCGW110308L-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.8 | O | O | |||||||
| VCGW110308M-2 | 2 | 2 | 6.35 | 3.18 | 2.8 | 0.8 | O | O | |||||||
| VCGW160404L-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.4 | O | O | O | ||||||
| VCGW160408L-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.8 | O | O | |||||||
| VCGW160402M-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ||||||||
| VCGW160404M-2 | 2 | 2 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ● | |||||||
| VCGW160408M-2 | 2 | 2 | 9.525 | 4.76 | 4.4 0.8 | ||||||||||
●标准库存需预定
菱形55°有孔
PCBN车削刀片(负型)
| 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||
| LE | IC | S | D1 | RE | BKK5Z | BH25 | BH25Z | ||
| 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | ● | ||
| CNGA120408LS-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | O | ● | |
| CNGA120412LS-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | |
| CNGA120404M-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | O | O |
| CNGA120408M-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● |
| CNGA120412M-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | ● |
| CNGA120412H-4 4 2.2 12.7 | 4.76 | 5.16 | 1.2 | ||||||
●标准库存需预定
| 订货号DNGA150404LS-4 4DNGA150408LS-4 | |||||||||
| 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||
| LE | IC | S | D1 | RE | BK225Z | BHC5Z | BHC25Z | ||
| 2.2 12.7 | 4.76 5.16 | 0.4 | O | O | |||||
| 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | O | O | |||
DNGA150404M-4 DNGA150408M-4DNGA150412M-4DNGA150412H-4 | 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | O | O |
| 4 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● | |
| 4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | O | |
| 4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | ● | |
●标准库存需预定
PCBN车削刀片(负型)
三角形60°有孔
订货号TNGA160404LS-6TNGA160408LS-6TNGA160404M-6 TNGA160408M-6TNGA160412M-6 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||
| LE | IC | S | D1 | RE | BK225Z | BH25Z | BH5Z | ||
| 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | O | ● | ||
| 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | O | O | ||
| 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | O | O | ||
| 6 | 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ● | ||
| 6 | 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | O | O | ||
●标准库存需预定
菱形35°有孔
订货号VNGA160404LS-4 4VNGA160408LS-4VNGA160404M-4 VNGA160408M-4VNGA160412M-4 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | |||||||
| LE | IC | S | D1 | RE | BKN225Z | BH25Z | BH25Z | |||
| 2.2 | 9.525 4.76 | 3.81 | 0.4 | O | ● | |||||
| 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | O | O | ||||
| 2.2 | 9.525 | 4.76 | 3.81 | 0.4 | O | O | O | |||
| 2.2 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ● | ● | |||
| 2.2 | 9.525 | 4.76 | 3.81 | 1.2 | O | O | O | |||
| DNGA150412H-4 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | O | O | |||
●标准库存需预定
PCBN车削刀片（负型)
六边形80°有孔
订货号WNGA080404LS-6 | 刃数 | 尺寸(mm) | PCBN牌号 | 涂层PCBN | ||||||
| LE | IC | S | D1 | RE | BKN225Z | BHC5Z | BH25Z | |||
| 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | O | ● | |||
| WNGA080408LS-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | O | O | O | |
| WNGA080404M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.4 | ● | O | O | |
| WNGA080408M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 0.8 | ● | ● | ● | |
| WNGA080412M-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | ● | O | ● | |
| WNGA080412H-6 | 6 | 2.2 | 12.7 | 4.76 | 5.16 | 1.2 | ● | O | ||
●标准库存需预定
订货号CNGN120404M-4 4 | 尺寸(mm) | PCBN牌号 | ||||||
| LE | IC | S | RE | BKN225S | BHN225S | |||
| 12.7 | 12.7 | 4.76 | 0.4 | O | O | |||
| CNGN120408LS-4 | 12.7 | 12.7 | 4.76 | 0.4 | O | ● | ||
| CNGN120408M-4 | 12.7 | 12.7 | 4.76 | 0.8 | 0 | O | ||
| CNGN120412M-4 | 12.7 | 12.7 | 4.76 | 1.2 | O | O | ||
| CNGN120704M-4 | 12.7 | 12.7 | 7.94 | 0.4 | O | O | ||
| CNGN120708M-4 | 12.7 | 12.7 | 7.94 | 0.8 | O | |||
| CNGN120712M-4 | 12.7 | 12.7 | 7.94 | 1.2 | ● | |||
| CNGN120716M-4 | 12.7 | 12.7 | 7.94 | 1.6 | O | O | ||
●标准库存需预定
菱形55°无孔
| 订货号 | 刃数 | 尺寸(mm) | PCBN牌号 | ||||
| LE | IC | S | RE | BKN225S | BHN225S | ||
DNGN110308M-4 4DNGN110312M-4 | 9.525 | 9.525 | 3.18 | 0.8 | O | O | |
| 9.525 | 9.525 | 3.18 | 1.2 | O | O | ||
●标准库存需预定
PCBN车削刀片（负型)
| 订货号SNGN090404M-8 | 刃数 | 尺寸(mm) | PCBN牌号 | |||||
| LE | IC | S | RE | BKN225S | BHN225S | |||
| 8 | 9.525 | 9.525 | 4.76 | 0.4 | O | 0 | ||
| SNGN090408M-8 | 8 | 9.525 | 9.525 | 4.76 | 0.8 | O | O | |
| SNGN090412M-8 | 8 | 9.525 | 9.525 | 4.76 | 1.2 | 0 | O | |
| SNGN120404M-8 | 8 | 12.7 | 12.7 | 4.76 | 0.4 | O | O | |
| SNGN120408M-8 | 8 | 12.7 | 12.7 | 4.76 | 0.8 | 0 | O | |
| SNGN120412M-8 | 8 | 12.7 | 12.7 | 4.76 | 1.2 | ● | O | |
| SNGN120708M-8 | 8 | 12.7 | 12.7 | 7.94 | 0.8 | O | O | |
| SNGN120712M-8 | 8 | 12.7 | 12.7 | 7.94 | 1.2 | O | O | |
| SNGN120716M-8 | 8 | 12.7 | 12.7 | 7.94 | 1.6 | ● | 0 | |
| SNGN150708M-8 | 8 | 15.875 | 15.875 | 7.94 | 0.8 | O | O | |
| SNGN150712M-8 | 8 | 15.875 | 15.875 | 7.94 | 1.2 | O | O | |
●标准库存需预定
订货号 | 刃数 | 尺寸(mm) | PCBN牌号 | |||||
| LE | IC | S | RE | BKN225S | BHN225S | |||
| WNGN080404M-6 | 6 | 8.72 | 12.7 | 4.76 | 0.4 | O | O | |
| WNGN080408M-6 | 6 | 8.72 | 12.7 | 4.76 | 0.8 | O | O | |
| WNGN080412M-6 | 6 | 8.72 | 12.7 | 4.76 | 1.2 | 0 | O | |
| WNGN080416M-6 | 6 | 8.72 | 12.7 | 4.76 | 1.6 | O | O | |
| WNGN080604M-6 | 6 | 8.72 | 12.7 | 6.35 | 0.4 | O | O | |
| WNGN080608M-6 | 6 | 8.72 | 12.7 | 6.35 | 0.8 | O | O | |
| WNGN080612M-6 | 6 | 8.72 | 12.7 | 6.35 | 1.2 | 0 | O | |
| WNGN080616M-6 | 6 | 8.72 | 12.7 | 6.35 | 1.6 | O | O | |
●标准库存需预定
PCBN车削刀片（正型）
| 刃数 | 尺寸(mm) | PCBN牌号 | |||||
| LE | IC | S | RE | BKN225S | BHN225S | ||
| - | - | 6 3.18 | - | O | |||
| - | - | 9.525 | 3.18 | - | O | ||
| - | - | 12.7 | 4.76 | - | |||
| RNGN120400H | - | - | 12.7 | 4.76 | - | O | |
| - | - | 12.7 | 7.94 | - | O | O | |
| RNGN150700M | - | - | 15.875 | 7.94 | - | O | O |
| - | 20 | 10 | - | O | O | ||
●标准库存需预定
| 订货号 | |||||||
| 刃数 | 尺寸(mm) | PCBN牌号 | |||||
| LE | IC | S | RE | BKN225S | BHN225S | ||
RCGN120700M - -RCGN160700M | 12.7 | 7.94 - | O | ||||
| 16 | 7.94 | - | O | ||||
●标准库存需预定
推荐切削参数
PCBN刀具
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||||
 | 球墨铸铁 | QT450~QT700 | 精加工 | 通用 | BKC120P | 150-300-500 | 0.10-0.20-0.50 | 0.05-0.12-0.3 |
| 合金铸铁 | ≥HB200 | 精加工 | 通用 | BKN115P | 200-400-800 | 0.05-0.20-0.50 | 0.05-0.20-0.40 | |
| 灰铸铁 | HB200~230 | 精加工 | 通用 | BKN115P | 400-600-1500 | 0.05-0.20-0.50 | 0.05-0.20-0.40 | |
| 灰铸铁 | HB200~230 | 精-粗加工 | 通用 | BKN225ZBKN225S | 400-600-1200 | 0.05-0.30-0.05 | 0.05-0.20-0.50 | |
| S | 粉末冶金 | HRB50~90 | 精加工 | 连续 | BSN115P | 50-150-300 | 0.05-0.20-0.5 | 0.05-0.12-0.30 |
 | 高硬度材料 | ≥HRC50 | 精加工 | 连续 | BHC115P | 120-150-220 | 0.05-0.10-0.20 | 0.05-0.10-0.20 |
| 高硬度材料 | ≥HRC50 | 精-粗加工 | 通用 | BHC125P | 100-130-180 | 0.05-0.10-0.50 | 0.05-0.10-0.20 | |
| 高硬度材料 | ≥HRC50 | 精-半精加工 | 断续 | BHC135P | 80-100-150 | 0.05-0.10-0.40 | 0.05-0.10-0.20 | |
| 高硬度材料 | ≥HRC50 | 精-半精加工 | 连续 | BHC210P | 100-150-260 | 0.05-0.10-0.20 | 0.05-0.10-0.20 | |
| 高硬度材料 | ≥HRC50 | 精-半精加工 | 连续 | BHC215Z | 120-150-230 | 0.05-0.10-0.20 | 0.05-0.10-0.15 | |
| 高硬度材料 | ≥HRC50 | 精-粗加工 | 通用 | BHC225P | 100-140-200 | 0.05-0.10-0.50 | 0.05-0.10-0.20 | |
| BHC225Z | ||||||||
| 高硬度材料 | ≥HRC50 | 精-粗加工 | 通用 | BHN225S | 100-150-190 | 0.05-0.10-0.50 | 0.05-0.10-0.20 | |
PCD刀具概述
PCD（聚晶金刚石）材料硬度高，耐磨性好，适用于铝合金、复合材料、石墨等非铁金属的半精加工、精加工，其主要应用于汽车行业、3C行业、航空航天行业等，典型加工零部件如汽车铝合金缸体缸盖、手机、笔记本、飞机扰流板等，在保证加工质量的前提下，实现高效率及高寿命要求，最终实现提效降本的目标，为客户带来更大的经济效益。
航空行业
汽车行业
PCD刀具 超硬刀具
PCD刀具
车削刀具
车削刀片型号表示规则
| 代号 | 形状 | 刀尖(度) | 图形 |
| H | 正六边形 | 120° | |
| 0 | 正八边形 | 135° | |
| P | 正五边形 | 108° | |
| S | 正方形 | 90° | |
| T | 正三角形 | 60° | |
| C | 80° | ||
| D | 菱形 | 55°35° | |
| V | |||
| W | 六边形 | 80° | |
| L | 长方形 | 90° | |
| A | 平行四边形 | 85° | |
| R | 圆形 | -- | O |
①形状代号
| 代号 | 后角(度) |
| A | 3° |
| B | 5° |
| C | 7° |
| D | 15° |
| E | 20° |
| F | 25° |
| G | 30° |
| N | 0° |
| P | 11° |
| 0 | 其他 |
②后角代号
| 代号(级) | 公差(毫米) | 公差(毫米) | ||||
| 刀尖高 | 厚度 | 内切圆(∅d) | 刀尖高 | 厚度 | 内切圆(∅d) | |
| A | ±0.005 | ±0.025 | ±0.025 | ±0.0002 | ±0.001 | ±0.001 |
| F | ±0.005 | ±0.025 | ±0.013 | ±0.0002 | ±0.001 | ±0.0005 |
| C | ±0.013 | ±0.025 | ±0.025 | ±0.0005 | ±0.001 | ±0.001 |
| H | ±0.013 | ±0.025 | ±0.013 | ±0.0005 | ±0.001 | ±0.0005 |
| E | ±0.025 | ±0.025 | ±0.025 | ±0.001 | ±0.001 | ±0.001 |
| G | ±0.025 | ±0.13 | ±0.025 | ±0.001 | ±0.005 | ±0.001 |
| J | ±0.005 | ±0.025 | ±0.05~0.13 | ±0.0002 | ±0.001 | ±0.002~0.005 |
| K | ±0.013 | ±0.025 | ±0.05~0.13 | ±0.0005 | ±0.001 | ±0.002~0.005 |
| L | ±0.025 | ±0.025 | ±0.05~0.13 | ±0.001 | ±0.001 | ±0.002~0.005 |
| M | ±0.08~0.18 | ±0.13 | ±0.05~0.13 | ±0.003~0.007 | ±0.005 | ±0.002~0.005 |
| N | ±0.08~0.18 | ±0.025 | ±0.05~0.13 | ±0.003~0.007 | ±0.001 | ±0.002~0.005 |
| U | ±0.13~0.38 | ±0.13 | ±0.08~0.25 | ±0.005~0.015 | ±0.005 | ±0.003~0.01 |
③精度代号
C
T
[①]
C
N
②
G
G
④
09
16
⑤
| ④断屑槽·孔代号 | ||||
| 代号 | 有无孔 | 孔的形状 | 断屑槽 | 形状 |
| N | 无 | 无 | ||
| R | 单面 | |||
| F | 双面 | |||
| A | 圆柱孔 | 无 | 日日 | |
| M | 单面 | |||
| G | 双面 | |||
| W | 部分圆柱孔单面40°~60° | 无 | ||
| T | 单面 | |||
| Q | 有 | 部分圆柱孔双面40°~60° | 无 | |
| U | 双面 | |||
| B | 部分圆柱孔单面70°~90° | 无 | ||
| H | 单面 | |||
| C | 部分圆柱孔双面70°~90° | 无 | ||
| J | 双面 | |||
| X | 1 | 一 | ||
⑤ISO切削刃长度代号 (mm)
| T 1 | SYY | CT 1 | 1 | D | K | 内切圆(mm) | ||||||||||
| 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | 代号 | 尺寸 | |
| 03 | 3.97 | 03 | 4.0 | 06 | 6.9 | 4 | 4.8 | 3.97 | ||||||||
| 04 | 4.76 | 04 | 4.8 | 08 | 8.2 | 5 | 5.8 | 4.76 | ||||||||
| 05 | 5 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 5 |
| 05 | 5.56 | 05 | 5.6 | 03 | 3.8 | 09 | 9.6 | 6 | 6.8 | 5.56 | ||||||
| 06 | 6 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 6 |
| 06 | 6.35 | 06 | 6.5 | 04 | 4.3 | 11 | 11 | 7 | 7.8 | 11 | 11.2 | 6.35 | ||||
| 07 | 7.94 | 08 | 8.1 | 05 | 5.4 | 13 | 13.8 | 9 | 9.7 | 7.94 | ||||||
| 08 | 8 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 8 |
| 09 | 9.525 | 09 | 9.525 | 09 | 9.7 | 06 | 6.5 | 16 | 16.5 | 11 | 11.6 | 16 | 16.6 | 16 | 19.7 | 9.525 |
| 10 | 10 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 10 |
| 12 | 12 | -- | -= | -- | -- | =- | -- | -- | =- | -- | =- | = | -- | -= | -- | 12 |
| 12 | 12.7 | 12 | 12.7 | 12 | 12.9 | 08 | 8.7 | 22 | 22 | 15 | 15.5 | 22 | 22.1 | 12.7 | ||
| 15 | 15.875 | 15 | 15.875 | 16 | 16.1 | 10 | 10.9 | 27 | 27.5 | 19 | 19.4 | 15.875 | ||||
| 16 | 16 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 16 |
| 19 | 19.05 | 19 | 19.05 | 19 | 19.3 | 13 | 13 | 33 | 33 | 23 | 23.3 | 19.05 | ||||
| 20 | 20 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 20 |
| 22 | 22.225 | 22 | 22.6 | 38 | 38.5 | 27 | 27.1 | 22.225 | ||||||||
| 25 | 25 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 25 |
| 25 | 25.4 | 25 | 25.4 | 25 | 25.8 | 44 | 44 | 31 | 31 | 25.4 | ||||||
| 31 | 31.75 | 31 | 31.75 | 32 | 32.2 | 55 | 55 | 38 | 38.8 | 31.75 | ||||||
| 31 | 32 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 32 |
车削刀片型号表示规则
⑥厚度代号
| 代号 | 前角 (度) |
| GN | 0°(通用型) |
| GB | 5°（通用型） |
| KB | 5°（高光型) |
⑧刃口形式代码PCD刀片
0
T3
04
GB
04
1
08
M
3
0]
8
0
| 代号 | 厚度 |
| 01 | 1.59 |
| 02 | 2.38 |
| T2 | 2.78 |
| 03 | 3.18 |
| T3 | 3.97 |
| 04 | 4.76 |
| 05 | 5.56 |
| 06 | 6.35 |
| 07 | 7.94 |
| 09 | 9.52 |
⑦刀尖代号
| 代号 | 刀尖圆弧半径 |
| 00 | 0.03 |
| 02 | 0.2 |
| 04 | 0.4 |
| 08 | 0.8 |
| 12 | 1.2 |
| 16 | 1.6 |
| 20 | 2.0 |
| 24 | 2.4 |
| 28 | 2.8 |
| 32 | 3.2 |
⑧刃口形式代码PCBN刀片
| 代号 | 刃口形式 |
| L | 连续标准型 |
| LS | 连续补充型 |
| M | 连续通用型 |
| H | 断续强化型 |
⑨可转位次数
| 代号 | 可转位次数 |
| 1 | 1 |
| 2 | 2 |
| 3 | 3 |
| 4 | 4 |
| 6 | 6 |
车削刀片一览表
| 形式 | 特点 | 菱形80° | 菱形55° | 三角形60° | 菱形35° | 六边形80° | 四边形90° | 圆形360° | |
| 焊片式 | · 用于更高精度、更长寿命的切削；·刀具形式多样化。 | 正型PCD |  |  |  |  |  | ||
| CCGW | DCGW | TCGW/TPGW | VCGW | RDEW | |||||
| P087 | P087 | P088-089 | P090 | P090 |
推荐切削参数
| ISO | 工件材料 | 切削范围 | 工况 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | |||||
 | 铝合金 | 精加工 | 通用 | DNN125P | 300-1200-3000 | 0.05-0.20-0.50 | 0.05-0.10-0.20 |
| 铜合金 | 精加工 | 通用 | DNN125P | 200-500-1000 | 0.05-0.40-2.00 | 0.05-0.10-0.20 | |
| 塑料 | 精加工 | 通用 | DNN125P | 100-600-1000 | 0.10-0.40-2.00 | 0.05-0.10-0.40 | |
| 木质、无机质板材 | 精加工 | 通用 | DNN125P | 200-2000-4000 | 0.10-0.50-2.00 | 0.05-0.10-0.40 | |
| 硬质合金 | 精加工 | 通用 | DNN125P | 10-20-30 | 0.05-0.20-0.50 | 0.05-0.10-0.20 | |
| 石墨 | 精加工 | 通用 | DNN125P | 100-300-600 | 0.10-0.40-2.00 | 0.10-0.25-1.00 | |
菱形80°有孔
订货号CCGW060202GB-1 | 刃数 | 尺寸(mm) | PCD牌号 | |||||
| LE | IC | S | D1 | RE | DNN25P | |||
| 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||
| CCGW060204GB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.4 | O | |
| CCGW09T302GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.2 | ● | |
| CCGW09T304GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.4 | O | |
| CCGW09T308GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.8 | O | |
| CCGW120404GB-1 | 1 | 3 | 12.7 | 4.76 | 5.5 | 0.4 | ● | |
| CCGW120408GB-1 | 1 | 3 | 12.7 | 4.76 | 5.5 | 0.8 | O | |
| CCGW060202KB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.2 | ● | |
| CCGW060204KB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.4 | O | |
| CCGW09T302KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.2 | O | |
| CCGW09T304KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.4 | ● | |
| CCGW09T308KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.8 | O | |
●标准库存需预定
菱形55°有孔
订货号DCGW070202GB-1 | ||||||||||
| 刃数 | 尺寸(mm) | PCD牌号 | ||||||||
| LE | IC | S | D1 | RE | DNN225P | |||||
| 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.2 | O | ||||
| DCGW070204GB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.4 | ● | |||
| DCGW11T302GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.2 | O | |||
| DCGW11T304GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.4 | O | |||
| DCGW11T308GB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.8 | ● | |||
| DCGW070202KB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.2 | O | |||
| DCGW070204KB-1 | 1 | 2.5 | 6.35 | 2.38 | 2.8 | 0.4 | ● | |||
| DCGW11T302KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.2 | O | |||
| DCGW11T304KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.4 | ● | |||
| DCGW11T308KB-1 | 1 | 3 | 9.525 | 3.97 | 4.4 | 0.8 | O | |||
●标准库存需预定
PCD车削刀片（正型）
三角形60°有孔
订货号 | ||||||||
| 刃数 | 尺寸(mm) | PCD牌号 | ||||||
| LE | IC | S | D1 | RE | DNN25P | |||
| 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.2 | O | ||
| TCGW080204GB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.4 | ● | |
| TCGW090202GB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.2 | O | |
| TCGW090204GB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.4 | ● | |
| TCGW110302GB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.2 | O | |
| TCGW110304GB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.4 | ● | |
| TCGW080202KB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.2 | O | |
| TCGW080204KB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.4 | ● | |
| TCGW090202KB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.2 | O | |
| TCGW090204KB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.4 | ● | |
| TCGW110302KB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.2 | O | |
| TCGW110304KB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.4 | ● | |
●标准库存需预定
三角形60°有孔
订货号 | ||||||||
| 刃数 | 尺寸(mm) | PCD牌号 | ||||||
| LE | IC | S | D1 | RE | DNN5P | |||
| TPGW080202GB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.2 | O | |
| TPGW080204GB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.4 | ||
| TPGW090202GB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.2 | O | |
| TPGW090204GB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.4 | ● | |
| TPGW110302GB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.2 | O | |
| TPGW110304GB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.4 | ● | |
| TPGW160402GB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.2 | O | |
| TPGW160404GB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.4 | O | |
| TPGW160408GB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.8 | ● | |
| TPGW080202KB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.2 | O | |
| TPGW080204KB-1 | 1 | 2.5 | 4.76 | 2.38 | 2.34 | 0.4 | ● | |
| TPGW090202KB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.2 | O | |
| TPGW090204KB-1 | 1 | 2.5 | 5.56 | 2.38 | 2.8 | 0.4 | ● | |
| TPGW110302KB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.2 | O | |
| TPGW110304KB-1 | 1 | 2.5 | 6.35 | 3.18 | 3.4 | 0.4 | ● | |
| TPGW160402KB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.2 | O | |
| TPGW160404KB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.4 | ● | |
| TPGW160408KB-1 | 1 | 3 | 9.525 | 4.76 | 4.4 | 0.8 | O | |
●标准库存需预定
PCD车削刀片(正型)
菱形35°有孔
订货号VCGW110302GB-1 1 | ||||||||
| 尺寸(mm) | PCD牌号 | |||||||
| LE | IC | S | D1 | RE | DNN25P | |||
| 3 | 6.35 | 3.18 | 2.8 | 0.2 | O | |||
| VCGW110304GB-1 | 3 | 6.35 | 3.18 | 2.8 | 0.4 | ● | ||
| VCGW160402GB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.2 | O | ||
| VCGW160404GB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ||
| VCGW160408GB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.8 | O | ||
| VCGW110302KB-1 | 3 | 6.35 | 3.18 | 2.8 | 0.2 | O | ||
| VCGW110304KB-1 | 3 | 6.35 | 3.18 | 2.8 | 0.4 | ● | ||
| VCGW160402KB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.2 | O | ||
| VCGW160404KB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ||
| VCGW160408KB-1 | 3 | 9.525 | 4.76 | 4.4 | 0.8 | O | ||
●标准库存需预定
圆形360°有孔
| 订货号 | 刃数 | 尺寸(mm) | PCD牌号 | ||
| IC | S | D1 | DNN25P | ||
RDEW080300GN-1 1 8RDEW100300GN-1 RDEW120400GN-1RDEW160400GN-1 | 3.18 | 2.94 | 0 | ||
| 3.18 | 4.6 | ● | |||
| 4.76 | 4.4 | O | |||
| 4.76 | 5.5 | ● | |||
●标准库存需预定
PCD刀具
整体铣削刀具
整体式PCD立铣刀型号（订货号）表示规则
DNR100 -
| ① | ||
| 工件材料 | ①系列号 | 系列说明 |
| 铝合金 | DNM100 | PCD圆角头立铣刀系列 |
| 石墨 | ||
| 复合材料 | ||
| 复合材料 | DNR100 | 高效加工PCD波齿立铣刀系列 |
S
S
2-
③
②
060
④
09
⑤
②底刃形状
| S | 平头 |
| B | 球头 |
| R | 圆弧角 |
| C | 刀尖倒角 |
③特征项
| N | 长颈 |
| H | 长柄 |
| L | 长刃 |
| S | 短刃 |
| 空 | 标准 |
④刃数
⑤刃径
| 0.6mm | 006 |
| 6mm | 060 |
| 10mm | 100 |
⑥特性码
平头\球头
a. 颈长
b. 刃长
6-06 10-10
圆角头 r0.2-02 r1-10
刀尖倒角 C0.03-03 C0.13-13
DNM100-RS1
1刃圆角头
| 订货号 | D | Lc | R | L1 | L | d | 图号 | 库存 |
| DNM100-RS1-02001 | 2 | 6 | 0.1 | 8 | 50 | 4 | 1 | ● |
| DNM100-RS1-02002 | 2 | 6 | 0.2 | 8 | 50 | 4 | 1 | ● |
| DNM100-RS1-02003 | 2 | 6 | 0.3 | 8 | 50 | 4 | 1 | |
| DNM100-RS1-03001 | 3 | 6 | 0.1 | 8 | 50 | 4 | 1 | |
| DNM100-RS1-03002 | 3 | 6 | 0.2 | 8 | 50 | 4 | 1 | ● |
| DNM100-RS1-03003 | 3 | 6 | 0.3 | 8 | 50 | 4 | 1 | ● |
●标准库存需预定
| D | 公差Tol |
| D≤3 | ±0.02 |
单位 (mm)
| 工件材料P | ||||||
| M | K | |||||
| 1234 | 5 | 123 | 123 | 123 | 4 | 5 |
| 碳钢、合金钢steels<35HRC | 合金钢<48HRC | 不锈钢 | 铸铁 | 铝合金 | 铜合金 | 石墨 |
| O | O | O | ||||
最适合适合
推荐切削参数 P97
推荐切削参数 P97
DNM100-RS2
2刃圆角头
| 订货号 | D | Lc | R | L1 | L | d | 图号 | 库存 |
| DNM100-RS2-04001 | 4 | 6 | 0.1 | 8 | 50 | 6 | 1 | ● |
| DNM100-RS2-04002 | 4 | 6 | 0.2 | 8 | 50 | 6 | 1 | ● |
| DNM100-RS2-04005 | 4 | 6 | 0.5 | 8 | 50 | 6 | 1 | ● |
| DNM100-RS2-06001 | 6 | 10 | 0.1 | 20 | 75 | 6 | 1 | |
| DNM100-RS2-06002 | 6 | 10 | 0.2 | 20 | 75 | 6 | 1 | |
| DNM100-RS2-06003 | 6 | 10 | 0.3 | 20 | 75 | 6 | 1 | |
| DNM100-RS2-06005 | 6 | 10 | 0.5 | 20 | 75 | 6 | 1 | |
| DNM100-RS2-08001 | 8 | 15 | 0.1 | 30 | 75 | 10 | 1 | |
| DNM100-RS2-08002 | 8 | 15 | 0.2 | 30 | 75 | 10 | 1 | ● |
| DNM100-RS2-08005 | 8 | 15 | 0.5 | 30 | 75 | 10 | 1 | |
| DNM100-RS2-08010 | 8 | 15 | 1 | 30 | 75 | 10 | 1 | |
| DNM100-RS2-10001 | 10 | 15 | 0.1 | 35 | 75 | 10 | 1 | ● |
| DNM100-RS2-10002 | 10 | 15 | 0.2 | 35 | 75 | 10 | 1 | |
| DNM100-RS2-10005 | 10 | 15 | 0.5 | 35 | 75 | 10 | 1 | |
| DNM100-RS2-10010 | 10 | 15 | 1 | 35 | 75 | 10 | 1 | |
| DNM100-RS2-10020 | 10 | 15 | 2 | 35 | 75 | 10 | 1 |
●标准库存需预定
单位(mm)
单位(mm)
| D | 公差Tol |
| D≤10 | ±0.02 |
| 工件材料 | ||||||
| P | M | K |  | |||
| 1234 | 5 | 123 | 123 | 123 | 4 | 5 |
| 碳钢、合金钢steels<35HRC | 合金钢<48HRC | 不锈钢 | 铸铁 | 铝合金 | 铜合金 | 石墨 |
| O | O | O | ||||
最适合适合
推荐切削参数P97
推荐切削参数P97
DNM100-RS3
3刃圆角头
| 订货号 | D | LC | R | L1 | L | d | 图号 | 库存 |
| DNM100-RS3-10001 | 10 | 15 | 0.1 | 35 | 75 | 10 | 1 | ● |
| DNM100-RS3-10002 | 10 | 15 | 0.2 | 35 | 75 | 10 | 1 | |
| DNM100-RS3-10005 | 10 | 15 | 0.5 | 35 | 75 | 10 | 1 | |
| DNM100-RS3-10010 | 10 | 15 | 1 | 35 | 75 | 10 | 1 | |
| DNM100-RS3-10020 | 10 | 15 | 2 | 35 | 75 | 10 | 1 | |
| DNM100-RS3-12002 | 12 | 15 | 0.2 | 40 | 75 | 12 | 1 | |
| DNM100-RS3-12005 | 12 | 15 | 0.5 | 40 | 75 | 12 | 1 | |
| DNM100-RS3-12010 | 12 | 15 | 1 | 40 | 75 | 12 | 1 | |
| DNM100-RS3-12020 | 12 | 15 | 2 | 40 | 75 | 12 | 1 | |
| DNM100-RS3-16002 | 16 | 15 | 0.2 | 45 | 100 | 16 | 1 | ● |
| DNM100-RS3-16005 | 16 | 15 | 0.5 | 45 | 100 | 16 | 1 | |
| DNM100-RS3-16010 | 16 | 15 | 1 | 45 | 100 | 16 | 1 | |
| DNM100-RS3-16020 | 16 | 15 | 2 | 45 | 100 | 16 | 1 | ● |
| DNM100-RS3-16030 | 16 | 15 | 3 | 45 | 100 | 16 | 1 |
●标准库存需预定
| D | 公差Tol |
| D≤16 | ±0.02 |
单位(mm)
| 工件材料 | ||||||
| P | M | K | N | |||
| 1234 | 5 | 123 | 123 | 123 | 4 | 5 |
| 碳钢、合金钢steels<35HRC | 合金钢<48HRC | 不锈钢 | 铸铁 | 铝合金 | 铜合金 | 石墨 |
| O | O | O | ||||
最适合适合
推荐切削参数P97
推荐切削参数P97
推荐切削参数
DNM100-RS1/RS2/ RS3复合材料/铝合金—侧铣
| 工件材料 | 切削量(mm) | 切削速度(m/min) | 刃径(mm) | 2 | 4 | 6 | 8 | 10 | 12 | 16 | |
 | 增强树脂基复合材料 | ap≤1.5D | 400(100~450) | 转速(min-¹) | 18000 | 16000 | 13270 | 11775 | 11145 | 10615 | 8000 |
| ae≤0.2D | 进给速度（mm/min) | 1800 | 2400 | 2650 | 2350 | 2230 | 2120 | 2400 | |||
| 铝合金 | ap≤1.5D | 150 | 转速(min-¹) | 16000 | 12000 | 12000 | 10000 | 8000 | 8000 | 5000 | |
| ae≤0.1D | (100~250) | 进给速度（mm/min) | 2000 | 2000 | 2400 | 2000 | 1600 | 1600 | 1500 | ||
DNM100-RS1/RS2/ RS3复合材料/铝合金—面铣
| 工件材料 | 切削量(mm) | 切削速度(m/min) | 刃径(mm) | 6 | 8 | 10 | 12 | 16 | |||
 | 增强树脂基复合材料 | ap≤0.1D | 400(100~450) | 转速(min-¹) | 13270 | 11775 | 11145 | 10615 | 8000 | ||
| ae≤0.6D | 进给速度（mm/min） | 2650 | 2350 | 2230 | 2120 | 2400 | |||||
| 铝合金 | ap≤0.1D | 150(100~250) | 转速(min-¹) | 12000 | 10000 | 8000 | 8000 | 5000 | |||
| ae≤0.6D | 进给速度（mm/min) | 2400 | 2000 | 1600 | 1600 | 1500 | |||||
1、请使用刚性较高的机床和刀柄。
2、请根据切削速度、设备刚性等情况可适当调整转速和进给速度。
3、上表是按照刀具悬长为直径4倍以下时所制订的，如果刀具悬长过长，加工时易产生振动，此时，请适当调整转速，进给速度和切深量。
DNR100-C3 NEW
3刃波齿铣刀
| 订货号 | D | Lc | C | L1 | L | d | 图号 | 库存 |
| DNR100-C3-06010 | 6 | 10 | 0.3 | 22 | 90 | 8 | 1 | ● |
| DNR100-C3-06015 | 6 | 15 | 0.3 | 27 | 90 | 8 | 1 | ● |
| DNR100-C3-08015 | 8 | 15 | 0.3 | 31 | 90 | 10 | 1 | ● |
| DNR100-C3-08020 | 8 | 20 | 0.3 | 35 | 90 | 10 | 1 | |
| DNR100-C3-10010 | 10 | 10 | 0.3 | 22 | 100 | 10 | 1 | O |
| DNR100-C3-10015 | 10 | 15 | 0.3 | 27 | 100 | 10 | 1 | O |
| DNR100-C3-10020 | 10 | 20 | 0.3 | 32 | 100 | 10 | 1 | O |
| DNR100-C3-12020 | 12 | 20 | 0.3 | 34 | 100 | 12 | 1 | O |
| DNR100-C3-12025 | 12 | 25 | 0.3 | 39 | 100 | 12 | 1 | O |
●标准库存需预定
| D | 公差Tol |
| D≤12 | ±0.02 |
单位(mm)
工件材料 | |||
| 123 | 4 | 5 | 6 |
| 铝合金 | 铜合金 | 复合材料 | 石墨 |
| O | O | ||
最适合适合
推荐切削参数P99
推荐切削参数P99
