该页无缩略图
菱形80°有孔
| 订货号 | 尺寸 (mm) | 金属 涂层硬质合金 陶瓷 | |||||||||
| LE IC | S | D1 | RE | GP110 GP66120 GPT130 | GP135 GM115 GM230 GMM315 GP120 GP130 | GM20 GM335 GM325 | GK215 G20 GK25 GK15 GK120 GK125 | GNT7120 GST7115 GST120 GST130 | |||
 | CCMT060202-MM | 6.5 | 6.35 | 2.38 2.8 | 0.2 | GPITM | |||||
| CCMT060204-MM | 6.5 | 6.35 | 2.38 2.8 | 0.4 | |||||||
| CCMT060208-MM | 6.5 | 6.35 2.38 | 2.8 | 0.8 | O C | ||||||
| CCMT09T302-MM | 9.7 | 9.525 3.97 | 4.4 | 0.2 | O | ||||||
| CCMT09T304-MM | 9.7 | 9.525 3.97 | 4.4 | 0.4 | |||||||
| CCMT09T308-MM | 9.7 | 9.525 3.97 | 4.4 | 0.8 | |||||||
| CCMT120404-MM | 12.9 12.7 | 4.76 | 5.56 | 0.4 | |||||||
 | CCMT120408-MM | 12.9 12.7 | 4.76 | 5.56 | 0.8 | ||||||
| CCMT060204-FP | 6.5 6.35 | 2.38 | 2.8 | 0.4 | O | ||||||
| CCMT09T302-FP | 9.7 | 9.525 3.97 | 4.4 | 0.2 | O O | ||||||
| CCMT09T304-FP | 9.7 | 9.525 3.97 | 4.4 | 0.4 | O O | O | ● O | ||||
| CCMT09T308-FP | 9.7 9.525 | 3.97 | 4.4 | 0.8 | O | O | O | ||||
| CCMT060202-GP | 6.5 | 6.35 2.38 | 2.8 | 0.2 | O | O | |||||
| CCMT060204-GP | 6.5 6.35 | 2.38 | 2.8 | 0.4 | O | ||||||
| CCMT060208-GP | 6.5 6.35 | 2.38 | 2.8 | 0.8 | |||||||
| CCMT09T302-GP | 9.7 9.525 | 3.97 | 4.4 | 0.2 | O | ||||||
| CCMT09T304-GP | 9.7 9.525 | 3.97 | 4.4 | 0.4 | |||||||
| CCMT09T308-GP | 9.7 9.525 | 3.97 | 4.4 | 0.8 | |||||||
| CCMT120404-GP | 12.9 12.7 | 4.76 | 5.56 | 0.4 | O | ||||||
| CCMT120408-GP | 12.9 12.7 | 4.76 | 5.56 | 0.8 | |||||||
 | CCMT120412-GP | 12.9 12.7 | 4.76 | 5.56 | 1.2 | O | |||||
| CCGT060202-GP | 6.5 6.35 | 2.38 | 2.8 | 0.2 | |||||||
| CCGT060204-GP | 6.5 6.35 | 2.38 | 2.8 | 0.4 | |||||||
| CCGT060208-GP | 6.5 6.35 | 2.38 | 2.8 | 0.8 | |||||||
| CCGT09T302-GP | 9.7 9.525 | 3.97 | 4.4 | 0.2 | |||||||
| CCGT09T304-GP CCGT09T308-GP | 9.7 9.525 | 3.97 | 4.4 | 0.4 | |||||||
| CCGT120404-GP | 9.7 | 9.525 3.97 12.7 4.76 | 4.4 5.56 | 0.8 0.4 | |||||||
| CCGT120408-GP | 12.9 12.9 | 12.7 4.76 | 5.56 | 0.8 | O | ||||||
| CCMT060202-TP | 6.5 6.35 | 2.38 | 2.8 | 0.2 | |||||||
| CCMT060204-TP | 6.5 | 6.35 | 2.8 | 0.4 | |||||||
 | 2.38 2.38 | ||||||||||
| CCMT060208-TP CCMT09T302-TP | 6.5 6.35 | 2.8 | 0.8 0.2 | ||||||||
| CCMT09T304-TP | 9.7 | 9.525 3.97 3.97 | 4.4 | ||||||||
| 9.7 9.525 | 4.4 | 0.4 | |||||||||
| CCMT09T308-TP | 9.7 9.525 | 3.97 4.76 | 4.4 5.56 | 0.8 0.4 | |||||||
| CCMT120404-TP CCMT120408-TP | 12.9 12.9 | 12.7 12.7 | 4.76 5.56 | 0.8 | |||||||
●标准库存需预定
车削刀片(正型)
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | ||||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP6110GPT | 1120 | GP130 | GP120GP | 130 | GP135 | GM15 | GM230 | GM315 | GM20 | GM3325 | GMM25 | GK215 | GK220 | GK25 | GK15 | GK120 | GK125 | GNT7120GST | 7115 | GST120 | GST130 | GPTMGP9TM | ||||
 | CCMT060204-KM | 6.5 | 6.35 | 2.38 2.8 | 0.4 | ● | ● | ||||||||||||||||||||||||
| CCMT09T304-KM | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ● | ||||||||||||||||||||||||
| CCMT09T308-KM | 9.7 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ● | ● | |||||||||||||||||||||||
| CCMT120404-KM | 12.9 | 12.7 | 4.76 | 5.56 | 0.4 | ● | |||||||||||||||||||||||||
| CCMT120408-KM | 12.9 | 12.7 | 4.76 | 5.56 | 0.8 | ● | ● | ● | |||||||||||||||||||||||
| CCMT120412-KM | 12.9 | 12.7 | 4.76 | 5.56 | 1.2 | ● | ● | ● | |||||||||||||||||||||||
 | CCGX060202-AL | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||||||||||||||||||||||||
| CCGX060204-AL | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | ● | |||||||||||||||||||||||||
| CCGX060208-AL | 6.5 | 6.35 | 2.38 | 2.8 | 0.8 | ● | |||||||||||||||||||||||||
| CCGX09T302-AL | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | ● | |||||||||||||||||||||||||
| CCGX09T304-AL | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ||||||||||||||||||||||||||
| CCGX09T308-AL | 9.7 | 9.525 | 3.97 | 4.4 | 0.8 | ● | |||||||||||||||||||||||||
| CCGX120402-AL | 12.9 | 12.7 | 4.76 | 5.5 | 0.2 | ||||||||||||||||||||||||||
| CCGX120404-AL | 12.9 | 12.7 | 4.76 | 5.5 | 0.4 | ● | |||||||||||||||||||||||||
| CCGX120408-AL | 12.912.7 | 4.765.5 0.8 | |||||||||||||||||||||||||||||
●标准库存需预定
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP110GPT | 1120GPT | 6130 | GP120 | GP130GP | 135GM | 15 | GM230 | GM3315GM | 320 | GM3325 | GM325GK | 215 | GK20 | GK25 | GK15 | G120 | GK125 | GNT7120 | GST115GST120GST130 | GPTM | GPTM | ||||
CPGT060204-GPCPGT060208-GP2 CPGT09T302-GP | 6.5 6.352.38 | 2.8 | 0.4 | |||||||||||||||||||||||||||
| 6.5 | 6.35 | 2.38 | 2.8 | 0.8 | O | |||||||||||||||||||||||||
| 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | ● | |||||||||||||||||||||||||
| CPGT09T304-GP | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| CPGT09T308-GP | 9.7 | 9.525 | 3.97 | 4.4 | 0.8 | O | ||||||||||||||||||||||||
| CPGT120404-GP | 12.9 | 12.7 | 4.76 | 5.56 | 0.4 | O | ||||||||||||||||||||||||
| CPGT120408-GP | 12.9 | 12.7 | 4.76 | 5.56 | 0.8 | ● | ||||||||||||||||||||||||
●标准库存需预定
| 订货号 | 尺寸(mm) | 金属涂层硬质合金陶瓷 | |||||||||||||||||
| LE | IC | S | D1 | RE | GP6110GP620GPT1130 GM115GM230GM35GM320GM325GMM25GK215 GKK225GK15 GNT120GST7115GP135GK20GK120GK125GST7120GP120GP130GST130GPTMGPTM | ||||||||||||||
 | DCMT070202-MM | 7.8 6.352.382.8 0.2 | ● | ||||||||||||||||
| DCMT070204-MM | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ● | ||||||||||||
| DCMT070208-MM | 7.8 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ●● | ||||||||||||
| DCMT11T302-MM | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ··· | |||||||||||||
| DCMT11T304-MM | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | ●●· | ● | ||||||||||||
| DCMT11T308-MM | 11.6 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ●● | ||||||||||||
 | DCMT070208-FP | 7.8 | 6.35 | 2.38 | 2.8 | 0.8 | O | ||||||||||||
| DCMT11T304-FP | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | OO | ● | O | |||||||||||
| DCMT11T308-FP | 11.6 | 9.5253.97 | 4.4 | 0.8 | O O | O O O O | |||||||||||||
 | DCMT070202-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | O | O O | |||||||||||
| DCMT070204-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | ····· | |||||||||||||
| DCMT070208-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.8 | ●· | O | ||||||||||||
| DCMT11T302-GP | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ● ○ | |||||||||||||
| DCMT11T304-GP | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | O | |||||||||||||
| DCMT11T308-GP | 11.6 | 9.5253.97 | 4.4 | 0.8 | ······ | ||||||||||||||
| DCMT11T312-GP | 11.6 | 9.5253.97 | 4.4 | 1.2 | O | ||||||||||||||
| DCMT150404-GP | 15.5 | 12.7 | 4.76 | 5.56 | 0.4 | O | ● | ||||||||||||
| DCMT150408-GP | 15.5 | 12.7 | 4.76 | 5.56 | 0.8 O O | O | |||||||||||||
| DCMT150412-GP | 15.5 | 12.7 | 4.76 | 5.56 | 1.2 | O | |||||||||||||
| DCGT070202-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | ||||||||||||||
| DCGT070204-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | ||||||||||||||
| DCGT070208-GP | 7.8 | 6.35 | 2.38 | 2.8 | 0.8 | O | |||||||||||||
| DCGT11T302-GP | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ||||||||||||||
| DCGT11T304-GP | 11.6 | 9.5253.97 | 4.4 | 0.4 | |||||||||||||||
| DCGT11T308-GP | 11.6 | 9.5253.97 | 4.4 | 0.8 | |||||||||||||||
 | DCMT070202-TP | 7.8 6.352.382.8 | 0.2 | ||||||||||||||||
| DCMT070204-TP | 7.8 6.352.38 | 2.8 | 0.4 | ||||||||||||||||
| DCMT070208-TP | 7.8 6.352.38 | 2.8 0.8 | |||||||||||||||||
| DCMT11T302-TP | 11.69.5253.97 | 4.4 0.2 | |||||||||||||||||
| DCMT11T304-TP | 11.69.5253.97 | 4.4 0.4 | |||||||||||||||||
| DCMT11T308-TP | 11.69.5253.97 4.4 0.8 | ||||||||||||||||||
●标准库存需预定
车削刀片(正型)
菱形55°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP6110 | GP6120GPT | 130 | GP120 | GP130 | GP135 | GM115 | GM230 | GM315 | GM320 | GM35GM | 325 | GK215 | GK220 | GKK25 | GK15 | GK120 | GK125 | GNT7120GST | 7115 | GST7120 | GST130 | GPTMGPTM | |||
DCMT11T304-KM | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ● | |||||||||||||||||||||||
| DCMT11T308-KM | 11.69 | .525 | 3.97 | 4.4 | 0.8 | |||||||||||||||||||||||||
 | DCGX070202-AL | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | ● | |||||||||||||||||||||||
| DCGX070204-AL | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ||||||||||||||||||||||||
| DCGX070208-AL | 7.8 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ||||||||||||||||||||||||
| DCGX11T302-AL | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ● | ||||||||||||||||||||||||
| DCGX11T304-AL | 11.69 | .525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| DCGX11T308-AL | 11.6 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ||||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
正方形90°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | ||||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP10 | GP120 | GP630 | GP120 | GP130 | GP135 | GM115 | GM230 | GM315 | GM320 | GM335 | GM325 | GK215 | G20 | GKK225 | GK15 | G120 | GK125 | GNT20 | GST115 | GST120 | GST130 | GPTMGPTM | ||||
 | SCMT09T304-MM | 9.5259.5253.97 | 4.4 | 0.4 | ● | ● | ● | ● | ● | ● | ● | ||||||||||||||||||||
| SCMT09T308-MM | 9.525 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ● | ● | ● | ● | ● | O | |||||||||||||||||||
| SCMT09T304-GP | 9.525 | 9.525 | 3.97 | 4.4 | 0.4 | ● | O | ● | O | ● | ● | ● | ● | ● | |||||||||||||||||
 | SCMT09T308-GP | 9.525 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ● | ● | ● | ● | ● | ● | ● | |||||||||||||||||
| SCMT120404-GP | 12.7 | 12.7 | 4.76 | 5.56 | 0.4 | ● | O | ● | ● | ● | |||||||||||||||||||||
| SCMT120408-GP | 12.7 | 12.7 | 4.76 | 5.56 | 0.8 | ● | ● | ● | ● | ● | ● | ● | ● | O | O | ||||||||||||||||
 | SCMT09T304-TP | 9.525 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| SCMT09T308-TP | 9.525 | 9.525 | 3.97 | 4.4 | 0.8 | ● | |||||||||||||||||||||||||
| SCMT120404-TP | 12.7 | 12.7 | 4.76 | 5.56 | 0.4 | ● | |||||||||||||||||||||||||
| SCMT120408-TP | 12.7 | 12.7 | 4.76 | 5.56 | 0.8 | ● | |||||||||||||||||||||||||
 | SCMT09T308-KM | 9.525 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ||||||||||||||||||||||||
| SCMT120408-KM | 12.7 | 12.7 | 4.76 | 5.56 | 0.8 | ● | ● | ||||||||||||||||||||||||
| SCMT120412-KM | 12.7 | 12.7 | 4.76 | 5.56 | 1.2 | ||||||||||||||||||||||||||
 | SCGX09T304-AL | 9.525 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| SCGX09T308-AL | 9.525 | 9.525 | 3.97 | 4.4 | 0.8 | ● | |||||||||||||||||||||||||
| SCGX120404-AL | 12.7 | 12.7 | 4.76 | 5.5 | 0.4 | ● | |||||||||||||||||||||||||
| SCGX120408-AL | 12.7 | 12.7 | 4.765.5 | 0.8 | |||||||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP1110GP66120GP1130GP120 | GP130GP135 | GM1115GM230 | GM315GM3220 | GMM3325GMM225GK215 | GK20GK25GK15GK120 | GK125 | GNT120 | GST115GST7120GST130GPTMGPTM | |||||||||||||||
 | TCMT110202-MM | 11 6.35 2.38 | 2.8 | 0.2 | ● | O | ● | ● | ●● | |||||||||||||||||||
| TCMT110204-MM | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ● | ● | ● | ●● | ||||||||||||||||||
| TCMT110208-MM | 11 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ● | |||||||||||||||||||||
| TCMT16T304-MM | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ●● | ● | ● | |||||||||||||||||||
| TCMT16T308-MM | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ●● | ● | ● | ● | C | |||||||||||||||||
 | TCMT090204-FP | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | O | |||||||||||||||||||||
| TCMT110204-FP | 11 | 6.35 | 2.38 | 2.8 | 0.4 | O | ||||||||||||||||||||||
| TCMT110304-FP | 11 | 6.35 | 2.38 | 3.18 | 0.4 | ● | ||||||||||||||||||||||
| TCMT16T304-FP | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | O | ||||||||||||||||||||||
 | TCMT090204-GP | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | ● | ● | ● | ● | ||||||||||||||||||
| TCMT110202-GP | 11 | 6.35 | 2.38 | 2.8 | 0.2 | ● | O | O | ||||||||||||||||||||
| TCMT110204-GP | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ● | ●● | ● | ● | ● | |||||||||||||||||
| TCMT110208-GP | 11 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ● | ● | O | ● | ● | |||||||||||||||||
| TCMT16T304-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ● | ● | C | ● | ● | ● | ||||||||||||||||
| TCMT16T308-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ● | ●● | ● | O | ||||||||||||||||||
| TCMT16T312-GP | 16.5 | 9.525 | 3.97 | 4.4 | 1.2 | ● | ● | ● | ● | |||||||||||||||||||
| TCMT220408-GP | 22 | 12.7 | 4.76 | 5.56 | 0.8 | ●● | O | ● | ||||||||||||||||||||
| TCGT090204-GP | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | ● | ||||||||||||||||||||||
| TCGT110202-GP | 11 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||||||||||||||||||||||
| TCGT110204-GP | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ||||||||||||||||||||||
| TCGT110208-GP | 11 | 6.35 | 2.38 | 2.8 | 0.8 | |||||||||||||||||||||||
| TCGT16T304-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||
| TCGT16T308-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | O | ||||||||||||||||||||||
 | TCMT090202-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.2 | ●● | |||||||||||||||||||||
| TCMT090204-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | ●● | ||||||||||||||||||||||
| TCMT090208-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.8 | ● | ||||||||||||||||||||||
| TCMT110204-TP | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ||||||||||||||||||||||
| TCMT110208-TP | 11 | 6.35 | 2.38 | 2.8 | 0.8 | |||||||||||||||||||||||
| TCMT16T304-TP | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ●● | ||||||||||||||||||||||
| TCMT16T308-TP | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | |||||||||||||||||||||||
 | TCMT110204-KM | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ||||||||||||||||||||||
| TCMT16T304-KM | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||
| TCMT16T308-KM | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP6110 | GP120GP | 61130 | GP120 | GP130 | GP135 | GM15 | GM230 | GM3315 | GMM20 | GM3325 | GM325 | GK215 | GK220GkK | 25 | GK15 | GK120 | GK125 | GNT120 | GST115 | GST20 | GST130 | GPTM | GPTM | ||
 | TCGX090204-AL | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | ● | |||||||||||||||||||||||
| TCGX110202-AL | 11 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||||||||||||||||||||||||
| TCGX110204-AL | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ||||||||||||||||||||||||
| TCGX110208-AL | 11 | 6.35 | 2.38 | 2.8 | 0.8 | ● | ||||||||||||||||||||||||
| TCGX16T302-AL | 16.5 | 9.525 | 3.97 | 4.4 | 0.2 | ● | ||||||||||||||||||||||||
| TCGX16T304-AL | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| TCGX16T308-AL | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | ● | ||||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
TP
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP6110 | GPT120 | GPT1630GP | 120GP | 130 | GP135 | GM15 | GM230 | GM315 | GM220 | GM3325GM | 325 | GK215 | G20 | GK25 | GK15 | GK120 | GK125 | GNT120 | GST115 | GST120 | GST130 | GPTMGPTM | |||
 | TPMT110202-MM | 11 | 6.35 | 2.38 | 2.8 | 0.2 | ● | O | ● | O | ||||||||||||||||||||
| TPMT110204-MM | 11 | 6.35 | 2.38 | 2.8 | 0.4 | ● | O | ● | O | |||||||||||||||||||||
| TPMT110304-MM | 11 | 6.35 | 3.18 | 3.4 | 0.4 | ● | ● | ● | ●● | |||||||||||||||||||||
 | TPGT110204-GP | 11 | 6.35 | 2.38 | 2.8 | 0.4 | O | |||||||||||||||||||||||
| TPGT110208-GP | 11 | 6.35 | 2.38 | 2.8 | 0.8 | O | ||||||||||||||||||||||||
| TPGT16T304-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.4 | O | ||||||||||||||||||||||||
| TPGT16T308-GP | 16.5 | 9.525 | 3.97 | 4.4 | 0.8 | O | ||||||||||||||||||||||||
 | TPMT090202-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.2 | ● | ● | ||||||||||||||||||||||
| TPMT090204-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.4 | ● | ● | |||||||||||||||||||||||
| TPMT090208-TP | 9.6 | 5.56 | 2.38 | 2.5 | 0.8 | ● | ||||||||||||||||||||||||
| TPMT110302-TP | 11 | 6.35 | 3.18 | 3.4 | 0.2 | ● | ● | |||||||||||||||||||||||
| TPMT110304-TP | 11 | 6.35 | 3.18 | 3.4 | 0.4 | ● | ||||||||||||||||||||||||
| TPMT110308-TP | 11 | 6.35 | 3.18 | 3.4 | 0.8 | ● | ||||||||||||||||||||||||
| TPMT160302-TP | 16.5 | 9.525 | 3.18 | 4.4 | 0.2 | ●● | ||||||||||||||||||||||||
| TPMT160304-TP | 16.5 | 9.525 | 3.18 | 4.4 | 0.4 | |||||||||||||||||||||||||
| TPMT160308-TP | 16.5 | 9.525 | 3.184.4 | 0.8 | ||||||||||||||||||||||||||
●标准库存需预定
菱形35°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | |||||||||||||||||||||||||||
| LE | IC | S | D1 | GPRE | 1110 | GPT1120 | GP66130 | G120 | GP130 | GP135 | GM115 | GM230 | GM3315GM | 3220 | GM335 | GM3225 | GK215 | GK220 | GK25 | GK15 | GK120 | GK125 | GNT720 | GST115 | GST120 | GST7130 | GPTMGP1TM | |||
| VBMT110304-MM | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | ● | ● | ● | ● | ● | ●● | ||||||||||||||||||
| VBMT110308-MM | 11.2 | 6.35 | 3.18 | 2.8 | 0.8 | ● | ● | |||||||||||||||||||||||
 | VBMT160402-MM | 16.6 | 9.525 | 4.76 | 4.4 | 0.2 | ● | ● | ● | O | O | |||||||||||||||||||
| VBMT160404-MM | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ● | ● | ● | ● | ● | ● | ● | |||||||||||||||||
| VBMT160408-MM | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | ● | ● | ||||||||||||||||||||||
 | VBMT160404-FP | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | O | ● | ● | O | ||||||||||||||||||||
| VBMT160408-FP | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | O | O | ● | O | ||||||||||||||||||||
 | VBMT160404-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ● | O | O | ● | ● | ● | ● | ||||||||||||||||
| VBMT160408-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | ● | ● | ● | ● | ● | ● | ||||||||||||||||||
| VBMT160412-GP | 16.6 | 9.525 | 4.76 | 4.4 | 1.2 | ● | O | ● | ||||||||||||||||||||||
 | VBMT110304-TP | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ||||||||||||||||||||||||
| VBMT110308-TP | 11.2 | 6.35 | 3.18 | 2.8 | 0.8 | ● | ||||||||||||||||||||||||
| VBMT160402-TP | 16.6 | 9.525 | 4.76 | 4.4 | 0.2 | ● | ● | |||||||||||||||||||||||
| VBMT160404-TP | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | |||||||||||||||||||||||||
| ●● | ||||||||||||||||||||||||||||||
| VBMT160408-TP | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | |||||||||||||||||||||||||
 | VBMT160408-KM | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ||||||||||||||||||||||||
| ●● | ||||||||||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
菱形35°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | 金属陶瓷 | ||||||||||||||||||||||||||||
| LE | IC | S | D1 | RE | GP6110GP66120GP66130 | GP120 | GP130 | GP135 | GM115 | GM230 | GMM315GM220 | GM35 | GMM325 | GK215GK20 | GKK25 | GK15 | GK120 | GK125 | GNT720GST7115GST20GST7130GPTMGP1TM | ||||||||||||
 | VCMT160404-MM 16.69.5254.764.4 0.4 O | ||||||||||||||||||||||||||||||
| VCMT160408-MM | 16.69.525 | 4.76 | 4.4 | 0.8 | ● | ● | ● | O | |||||||||||||||||||||||
| VCMT160408-FP | 16.6 | 9.5254.76 | 4.4 | 0.8 | O | O | |||||||||||||||||||||||||
| VCMT110304-GP | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | O | ● | ● | |||||||||||||||||||||||
| VCMT110308-GP | 11.2 | 6.35 | 3.18 | 2.8 | 0.8 | O | ● | ||||||||||||||||||||||||
| VCMT160404-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | O | ● | ● | ● | ● | ||||||||||||||||||||
| VCMT160408-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | O | ● | ● | ● | ● | ||||||||||||||||||||
| VCGT110304-GP | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | |||||||||||||||||||||||||
| VCGT160404-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | |||||||||||||||||||||||||
| VCGT160408-GP | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | O | |||||||||||||||||||||||||
 | VCMT160404-KM | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ||||||||||||||||||||||||
| VCMT160408-KM | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | |||||||||||||||||||||||||
 | VCGX110302-AL | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | ● | ||||||||||||||||||||||||
| VCGX110304-AL | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | |||||||||||||||||||||||||
| VCGX110308-AL | 11.2 | 6.35 | 3.18 | 2.8 | 0.8 | ● | |||||||||||||||||||||||||
| VCGX160402-AL | 16.6 | 9.525 | 4.76 | 4.4 | 0.2 | ● | |||||||||||||||||||||||||
| VCGX160404-AL | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | |||||||||||||||||||||||||
| VCGX160408-AL | 16.6 | 9.525 | 4.76 | 4.4 | 0.8 | ● | |||||||||||||||||||||||||
| VCGX160412-AL | 16.6 | 9.525 | 4.76 | 4.4 | 1.2 | O | |||||||||||||||||||||||||
| VCGX220512-AL | 22.1 | 12.7 | 5.56 | 5.6 | 1.2 | O | |||||||||||||||||||||||||
| VCGX220516-AL | 22.1 | 12.7 | 5.56 | 5.6 | 1.6 | ● | |||||||||||||||||||||||||
| VCGX220530-AL | 22.1 | 12.7 | 5.56 | 5.6 | 3.0 | ||||||||||||||||||||||||||
●标准库存需预定
车削刀片(正型)
六边形80°有孔
| WCMT06T304-GP | 订货号 | ||
| 6.5 | 55 | E | (mm)R |
| 9.525 | 9.525 | I | |
| 3.97 | 3.97 | S | |
| 4.480O | 4.4 | TD | |
| 40 | R | ||
| O | GPT6110 | 涂层硬质合金 | |
| GPT6120 | |||
| GPT6130 | |||
| GP1120 | |||
| GP1130 | |||
| O | GP1135 | ||
| GM1115 | |||
| GM1230 | |||
| GM3315 | |||
| GM3220 | |||
| GM3325 | |||
| GM3225 | |||
| GK1215 | |||
| GK1220 | |||
| GK1225 | |||
| GK1115 | |||
| GK1120 | |||
| GK1125 | |||
| GNT7120 | |||
| GST7115 | |||
| GST7120 | |||
| GST7130 | |||
| GP31TM | 民前即 | ||
| GP91TM | |||
●标准库存需预定
推荐切削参数（负型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | |||||||
| P 软钢 ≤HB180 | 连续 | GPT6110 | 240-300-400 | 0.40-0.80-2.00 | |||||
| 通用 | QF | GPT6120 | 200-280-380 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||
| GP1120 | 200-260-360 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||
| 精加工 | 断续 | GPT6130 | 180-240-320 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||
| GP1135 | 170-220-300 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||
| 连续 | TF | GP31TM | 220-300-380 | 0.30-0.70-1.80 | 0.07-0.14-0.35 | ||||
| GP91TM | 200-280-350 | 0.30-0.70-1.80 | 0.07-0.14-0.35 | ||||||
| 半精加工 | 连续 | GPT6110 | 220-280-380 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||
| 通用 | QM | GPT6120 | 180-250-340 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||
| GP1120 | 180-230-320 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| 断续 | GPT6130 | 160-230-300 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||
| GP1130 | 160-210-300 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| GP1135 | 150-190-280 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| 连续 | TP | GP31TM | 220-300-380 | 0.30-1.00-3.00 | 0.05-0.12-0.28 | ||||
| GP91TM | 200-280-350 | 0.30-1.20-3.00 | 0.05-0.15-0.28 | ||||||
| 连续 | TS | GP31TM | 200-280-350 | 0.50-1.00-3.00 | 0.10-0.15-0.35 | ||||
| GP91TM | 200-260-330 | 0.50-1.20-3.00 | 0.10-0.20-0.35 | ||||||
| 连续 | GPT6110 | 150-220-280 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||
| 通用 | GPT6120 | 140-210-270 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||
| 粗加工 | 断续 | QR | GPT6130 | 120-190-250 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||
| GP1130 | 120-170-250 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | ||||||
| GP1135 | 110-150-230 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | ||||||
| 连续 | QH | GPT6110 | 100-170-230 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | ||||
| 重载加工 | 通用 | GPT6120 | 100-160-220 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | ||||
| 断续 | GPT6130 | 90-150-210 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||||
| GP1135 | 80-130-190 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | ||||||
推荐切削参数（负型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | |||||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||||||||
| P碳钢、合金钢 | HB180-280 | 精加工 | 连续 | GPT6110 | 220-270-360 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||
| 通用 | QF | GPT6120 | 180-250-340 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||||
| GP1120 | 180-230-320 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||||||
| 断续 | GPT6130 | 160-220-300 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||||
| GP1135 | 150-200-280 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||||||
| 半精加工 | 连续 | GPT6110 | 180-250-340 | 0.80-2.00-4.00 | 0.15-0.22-0.40 | |||||||
| 通用 | QM | GPT6120 | 140-230-320 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||||
| GP1120 | 140-210-300 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||||||
| 断续 | GPT6130 | 120-210-280 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||||
| GP1130 | 120-190-280 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||||||
| GP1135 | 100-170-260 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||||||
| 连续 | TP | GP31TM | 200-270-350 | 0.30-1.00-2.50 | 0.05-0.12-0.28 | |||||||
| GP91TM | 180-250-330 | 0.30-1.20-2.50 | 0.05-0.15-0.28 | |||||||||
| 连续 | TS | GP31TM | 180-250-330 | 0.50-1.00-3.00 | 0.10-0.15-0.35 | |||||||
| GP91TM | 180-230-310 | 0.50-1.20-3.00 | 0.10-0.20-0.35 | |||||||||
| 粗加工 | 连续 | GPT6110 | 140-210-270 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||||
| 通用 | GPT6120 | 130-200-260 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | ||||||||
| 断续 | QR | GPT6130 | 110-180-240 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||||
| GP1130 | 110-160-240 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||||||
| GP1135 | 100-140-220 | 1.50-3.50-6.00 | 0.20-0.30-0.60 | |||||||||
推荐切削参数(负型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | |||||||
| P碳钢、合金钢HB280-350 | 重载加工 | 连续 | QH | GPT6110 | 90-160-220 | 3.00-6.00-12.0 | |||
| 通用 | GPT6120 | 90-150-210 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||||
| 断续 | GPT6130 | 80-140-200 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||||
| GP1135 | 70-120-180 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | ||||||
| 精加工 | 连续 | QF | GPT6110 | 180-220-290 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||
| 通用 | GPT6120 | 150-200-270 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||
| GP1120 | 150-180-250 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||
| 断续 | GPT6130 | 130-170-230 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | |||||
| GP1130 | 130-150-230 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||
| GP1135 | 110-130-210 | 0.40-0.80-2.00 | 0.08-0.15-0.35 | ||||||
| 半精加工 | 连续 | QM | GPT6110 | 140-200-270 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||
| 通用 | GPT6120 | 110-190-260 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||
| GP1120 | 110-170-240 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| 断续 | GPT6130 | 100-170-220 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | |||||
| GP1130 | 100-150-220 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| GP1135 | 900-130-200 | 0.80-2.00-4.00 | 0.15-0.20-0.40 | ||||||
| 连续 | TP | GP31TM | 180-250-320 | 0.30-1.00-2.50 | 0.05-0.12-0.28 | ||||
| GP91TM | 170-230-300 | 0.30-1.20-2.50 | 0.05-0.15-0.28 | ||||||
| 连续 | TS | GP31TM | 170-230-300 | 0.50-1.00-3.00 | 0.10-0.15-0.35 | ||||
| GP91TM | 150-210-280 | 0.50-1.20-3.00 | 0.10-0.20-0.35 | ||||||
| 粗加工 | 连续 | GPT6110 | 120-190-230 | 2.00-3.50-6.50 | 0.20-0.30-0.60 | ||||
| 通用 | QR | GPT6120 | 110-180-220 | 2.00-3.50-6.50 | 0.20-0.30-0.60 | ||||
| 断续 | GPT6130 | 90-160-200 | 2.00-3.50-6.50 | 0.20-0.30-0.60 | |||||
| GP1130 | 90-140-200 | 2.00-3.50-6.50 | 0.20-0.30-0.60 | ||||||
| GP1135 | 80-120-180 | 2.00-3.50-6.50 | 0.20-0.30-0.60 | ||||||
| 连续 | GPT6110 | 80-130-190 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||||
| 重载加工 | 通用 | QH | GPT6120 | 80-120-180 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||
| 断续 | GPT6130 | 70-110-170 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | |||||
| GP1135 | 60-90-150 | 3.00-6.00-12.0 | 0.35-0.60-1.10 | ||||||
推荐切削参数(负型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | |||||||
| M | 马氏体铁素体SUS410SUS430等 | ≤HB230 | 通用 | SF | GM3220 | 100-150-200 | 0.10-0.80-1.50 | 0.08-0.12-0.25 | |
| 精加工 | 通用 | YF | GM3220 | 100-150-200 | 0.10-1.0-2.0 | 0.08-0.15-0.3 | |||
| 断续 | GM3325 | 100-150-200 | 0.10-1.0-2.0 | 0.08-0.15-0.3 | |||||
| 连续 | GM1115 | 200-250-300 | 0.50-1.20-2.00 | 0.10-0.20-0.40 | |||||
| GM3315 | 120-160-200 | 1.00-2.00-3.00 | 0.15-0.20-0.30 | ||||||
| 通用 | SM | GM3220 | 60-130-180 | 1.00-2.00-3.00 | 0.15-0.20-0.35 | ||||
| 半精加工 | 断续 | GM1230 | 180-230-280 | 0.50-1.80-3.00 | 0.10-0.20-0.40 | ||||
| GM3325 | 60-130-180 | 1.00-2.00-3.00 | 0.15-0.20-0.35 | ||||||
| 连续 | GM1115 | 200-250-300 | 0.80-1.80-3.50 | 0.08-0.18-0.40 | |||||
| GM3315 | 120-160-200 | 0.80-1.80-3.50 | 0.08-0.18-0.30 | ||||||
| 通用 | LM | GM3220 | 60-130-180 | 0.80-1.80-3.50 | 0.08-0.20-0.40 | ||||
| 断续 | GM1230 | 180-230-280 | 0.80-1.80-3.50 | 0.08-0.18-0.40 | |||||
| GM3325 | 60-130-180 | 0.80-1.80-3.50 | 0.08-0.20-0.40 | ||||||
| 粗加工 | 连续 | GM1115 | 200-250-300 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | ||||
| 通用 | LR | GM3220 | 60-130-180 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | ||||
| 断续 | GM3225 | 60-130-180 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | |||||
| 奥氏体SUS201SUS304SUS316等 | ≤HB250 | 精加工 | 通用 | SF | GM3220 | 80-130-180 | 0.10-0.80-1.50 | 0.08-0.12-0.25 | |
| 通用 | YF | GM3220 | 80-130-180 | 0.10-1.0-2.0 | 0.08-0.15-0.3 | ||||
| 断续 | GM3325 | 80-130-180 | 0.10-1.0-2.0 | 0.08-0.15-0.3 | |||||
| 半精加工 | 连续 | GM1115 | 180-230-280 | 0.50-1.20-2.00 | 0.10-0.20-0.40 | ||||
| GM3315 | 100-130-160 | 1.00-2.00-3.00 | 0.15-0.20-0.30 | ||||||
| 通用 | SM | GM3220 | 60-110-150 | 1.00-2.00-3.00 | 0.15-0.20-0.35 | ||||
| 断续 | GM1230 | 180-230-280 | 0.50-1.80-3.00 | 0.10-0.20-0.40 | |||||
| GM3325 | 60-110-150 | 1.00-2.00-3.00 | 0.15-0.20-0.35 | ||||||
| 连续 | GM1115 | 200-250-300 | 0.80-1.80-3.50 | 0.08-0.18-0.40 | |||||
| GM3315 | 100-130-160 | 0.80-1.80-3.50 | 0.08-0.18-0.30 | ||||||
| 通用 | LM | GM3220 | 60-110-150 | 0.80-1.80-3.50 | 0.08-0.20-0.40 | ||||
| 断续 | GM1230 | 160-200-240 | 0.80-1.80-3.50 | 0.08-0.18-0.40 | |||||
| GM3325 | 60-110-150 | 0.80-1.80-3.50 | 0.08-0.20-0.40 | ||||||
| 连续 | GM1115 | 180-230-280 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | |||||
| 粗加工 | 通用 | LR | GM3220 | 60-110-150 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | |||
| 断续 | GM3225 | 60-110-150 | 1.50-3.00-5.00 | 0.15-0.30-0.50 | |||||
| 灰口铸铁K FC200FC250FC300等 | ≤HB220 | 连续 | WMV | GK1115 | 230-350-500 | 1.00-2.00-6.00 | 0.20-0.40-0.80 | ||
| 断续 | GK1125 | 220-320-480 | 1.00-2.00-6.00 | 0.20-0.40-0.80 | |||||
| 连续 | GK1115 | 230-350-500 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||
| 半精加工 | 通用 | MK | GK1120 | 230-320-500 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||
| 断续 | GK1125 | 220-320-480 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||
| 连续 | GK1215 | 230-350-500 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||
| 通用 | UK | GK1220 | 230-320-500 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | ||||
| 断续 | GK1225 | 220-320-480 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||
| 连续 | GK1215 | 220-320-480 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | |||||
| 粗加工 | 通用 | HK | GK1220 | 220-300-480 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | |||
| 断续 | GK1225 | 210-300-450 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | |||||
| 连续 | GK1215 | 210-300-450 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | |||||
| 重载加工 | 通用 | 无 | GK1220 | 210-280-450 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | |||
| 断续 | GK1225 | 200-280-430 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | |||||
推荐切削参数（负型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | |||||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||||||||
| K | 球墨铸铁FCD450FCD500FCD600等 | ≤HB300 | 半精加工 | 连续 | WMV | GK1115 | 180-260-380 | 1.00-2.00-6.00 | 0.20-0.40-0.80 | |||
| 断续 | GK1125 | 160-230-350 | 1.00-2.00-6.00 | 0.20-0.40-0.80 | ||||||||
| 连续 | GK1115 | 180-260-380 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | ||||||||
| 通用 | MK | GK1120 | 180-260-380 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||||
| 断续 | GK1125 | 160-230-350 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | ||||||||
| 连续 | GK1215 | 180-260-380 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | ||||||||
| 通用 | UK | GK1220 | 180-260-380 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | |||||||
| 断续 | GK1225 | 160-230-350 | 0.50-1.50-3.00 | 0.10-0.20-0.40 | ||||||||
| 连续 | GK1215 | 180-240-360 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | ||||||||
| 粗加工 | 通用 | HK | GK1220 | 180-240-360 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | ||||||
| 断续 | GK1225 | 160-230-350 | 0.50-2.00-4.00 | 0.10-0.25-0.50 | ||||||||
| 连续 | GK1215 | 180-220-350 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | ||||||||
| 重载加工 | 通用 | 无 | GK1220 | 180-220-350 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | ||||||
| 无 | ||||||||||||
| 断续 | GK1225 | 160-230-350 | 1.00-2.50-6.00 | 0.20-0.30-0.60 | ||||||||
| S | 高温合金钛合金等 | ≤HRC45 | 连续 | GST7115 | 20-40-70 | 0.50-1.50-3.00 | 0.10-0.15-0.22 | |||||
| 通用 | EL | GST7120 | 20-40-70 | 0.50-1.50-3.00 | 0.10-0.15-0.22 | |||||||
| 精-半精加工 | 断续 | GST7130 | 20-30-40 | 0.50-1.50-3.00 | 0.10-0.15-0.22 | |||||||
| 连续 | GST7115 | 20-40-70 | 0.50-1.50-3.00 | 0.10-0.20-0.30 | ||||||||
| 通用 | SML | GST7120 | 20-40-70 | 0.50-1.50-3.00 | 0.10-0.20-0.30 | |||||||
| 断续 | GST7130 | 20-30-40 | 0.50-1.50-3.00 | 0.10-0.20-0.30 | ||||||||
| 连续 | GST7115 | 20-40-70 | 1.00-2.50-4.00 | 0.10-0.20-0.35 | ||||||||
| 通用 | EM | GST7120 | 20-40-70 | 1.00-2.50-4.00 | 0.10-0.20-0.35 | |||||||
| 半精加工 | 断续 | GST7130 | 20-30-40 | 1.00-2.50-4.00 | 0.10-0.20-0.35 | |||||||
| 连续 | GST7115 | 20-40-70 | 1.00-2.50-4.00 | 0.10-0.25-0.40 | ||||||||
| 通用 | SMM | GST7120 | 20-40-70 | 1.00-2.50-4.00 | 0.10-0.25-0.40 | |||||||
| 断续 | GST7130 | 20-30-40 | 1.00-2.50-4.00 | 0.10-0.25-0.40 | ||||||||
推荐切削参数(正型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | |||||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | ||||||||||
| P碳钢、合金钢HB280-350 | 精加工 | GP31TM | ||||||||||
| 连续 | GP91TM | 200-250-310 | 0.10-0.60-1.50 | 0.03-0.10-0.20 | ||||||||
| MM | GPT6110 | 210-260-340 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 通用 | GPT6120 | 180-240-320 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 断续 | GPT6130 | 170-220-280 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 连续 | GP31TM | 220-280-340 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| FP | GP91TM | 200-250-310 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| GPT6110 | 210-260-340 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||||||
| 通用 | GPT6120 | 180-240-320 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 断续 | GPT6130 | 170-220-280 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 半精-粗加工 | 通用 | GP | GP1120 | 170-200-280 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||
| 断续 | GP1130 | 150-180-260 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||||
| 半精加工 | 连续 | TP | GP31TM | 200-250-300 | 0.30-1.00-3.00 | 0.05-0.15-0.25 | ||||||
| GP91TM | 180-230-300 | 0.30-1.00-3.00 | 0.05-0.15-0.25 | |||||||||
| 精加工 | GP31TM | 200-250-330 | 0.10-0.50-1.00 | 0.03-0.10-0.20 | ||||||||
| 连续 | GP91TM | 180-230-300 | 0.10-0.60-1.50 | 0.03-0.12-0.20 | ||||||||
| MM | GPT6110 | 180-220-290 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 通用 | GPT6120 | 150-200-280 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 断续 | GPT6130 | 140-180-240 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 连续 | GP31TM | 200-250-330 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| FP | GP91TM | 180-230-300 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| GPT6110 | 180-220-290 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||||||
| 通用 | GPT6120 | 150-200-280 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 断续 | GPT6130 | 140-180-240 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 半精-粗加工 | 通用 | GP | GP1120 | 140-160-240 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||
| 断续 | GP1130 | 120-140-220 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||||
| 半精加工 | 连续 | TP | GP31TM | 180-210-280 | 0.30-1.00-3.00 | 0.05-0.15-0.25 | ||||||
| GP91TM | 160-190-270 | 0.30-1.00-3.00 | 0.05-0.15-0.25 | |||||||||
| GP31TM | 160-220-300 | 0.10-0.60-1.50 | 0.03-0.10-0.20 | |||||||||
| 连续 | GP91TM | 140-200-280 | 0.10-0.60-1.50 | 0.03-0.10-0.20 | ||||||||
| MM | GPT6110 | 160-200-260 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 通用 | GPT6120 | 130-180-250 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | ||||||||
| 精加工 | 断续 | GPT6130 | 120-160-210 | 0.10-0.60-1.50 | 0.05-0.10-0.20 | |||||||
| GP31TM | 160-220-300 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||||||
| 连续 | FP | GP91TM | 140-200-280 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||||
| GPT6110 | 160-200-260 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||||||
| 通用 | GPT6120 | 130-180-250 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 断续 | GPT6130 | 120-160-210 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||||||
| 半精-粗加工 | 通用 | GP | GP1120 | 120-160-210 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||
| 断续 | GP1130 | 100-140-220 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||||
| 半精加工 | 连续 | TP | GP31TM | 160-200-270 | 0.30-1.00-3.00 | 0.05-0.12-0.25 | ||||||
| GP91TM | 130-160-250 | 0.30-1.20-3.00 | 0.05-0.15-0.25 | |||||||||
推荐切削参数(正型)
| ISO | 工件材料 | 硬度 | 切削范围 | 工况 | 断屑槽 | 牌号 | 下限-推荐-上限 | ||
| 切削速度Vc(m/min) | 切深ap(mm) | 进给量f(mm/rev) | |||||||
| M | 马氏体铁素体SUS410SUS430 | ≤HB300 | 连续 | GM1115 | 200-250-300 | 0.40-0.70-1.50 | 0.05-0.10-0.20 | ||
| 精-半精加工 | 通用 | MM | GM3220 | 40-80-140 | 0.40-0.70-1.50 | 0.05-0.10-0.20 | |||
| 断续 | GM3225 | 40-80-140 | 0.40-0.70-1.50 | 0.05-0.10-0.20 | |||||
| 连续 | GM1115 | 200-250-300 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||
| 通用 | FP | GM3220 | 40-80-140 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||
| 断续 | GM3225 | 40-80-140 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||
| 半精-粗加工 | 连续 | GM1115 | 150-200-250 | 0.50-1.00-2.50 | 0.07-0.12-0.30 | ||||
| GM3315 | 60-100-160 | 0.50-1.00-2.50 | 0.07-0.12-0.25 | ||||||
| 通用 | GP | GM3220 | 40-80-140 | 0.50-1.00-2.50 | 0.07-0.12-0.30 | ||||
| 断续 | GM1230 | 120-150-180 | 0.50-1.00-2.50 | 0.07-0.12-0.30 | |||||
| GM3325 | 40-80-140 | 0.50-1.00-2.50 | 0.07-0.12-0.30 | ||||||
| 奥氏体SUS201SUS304 | ≤HB250 | 精-半精加工 | 连续 | GM1115 | 200-240-300 | 0.50-0.70-1.50 | 0.05-0.10-0.20 | ||
| 通用 | MM | GM3220 | 40-70-140 | 0.50-0.70-1.50 | 0.05-0.10-0.20 | ||||
| 断续 | GM3225 | 40-70-140 | 0.50-0.70-1.50 | 0.05-0.10-0.20 | |||||
| 连续 | GM1115 | 200-250-300 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||
| 通用 | FP | GM3220 | 40-80-140 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | ||||
| 断续 | GM3225 | 40-80-140 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |||||
| SUS316 | 连续 | GM1115 | 150-190-250 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||
| GM3315 | 50-90-150 | 0.40-1.00-2.50 | 0.07-0.12-0.25 | ||||||
| 半精-粗加工 | 通用 | GP | GM3220 | 40-70-140 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | |||
| 断续 | GM1230 | 120-140-180 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | |||||
| GM3325 | 40-70-140 | 0.40-1.00-2.50 | 0.07-0.12-0.30 | ||||||
| K | 灰口铸铁FC200FC250FC300等 | ≤HB250 | 精加工 | 连续 | FP | GK1115 | 180-260-360 | 0.10-0.50-1.00 | 0.06-0.11-0.25 |
| 精-半精加工 | 连续 | GK1215 | 180-280-380 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | ||||
| 通用 | GP | GK1220 | 180-260-380 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | ||||
| 断续 | GK1225 | 160-250-350 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | |||||
| 半精-粗加工 | 连续 | GK1115 | 180-260-360 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | ||||
| 通用 | KM | GK1120 | 180-240-360 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | ||||
| 断续 | GK1125 | 160-230-340 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | |||||
| 球墨铸铁FCD450FCD500FCD600等 | ≤HB270 | 精加工 | 连续 | FP | GK1115 | 180-260-360 | 0.10-0.50-1.00 | 0.06-0.11-0.25 | |
| 精-半精加工 | 连续 | GK1215 | 160-250-350 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | ||||
| 通用 | GP | GK1220 | 160-220-350 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | ||||
| 断续 | GK1225 | 140-230-330 | 0.30-0.80-2.00 | 0.05-0.12-0.25 | |||||
| 半精-粗加工 | 连续 | GK1115 | 160-230-330 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | ||||
| 通用 | KM | GK1120 | 160-200-330 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | ||||
| 断续 | GK1125 | 140-200-310 | 1.00-2.00-4.00 | 0.13-0.20-0.40 | |||||
| N | 铝合金 | 淬硬HB90-100 | 精-半精加工 | 通用 | AL | GNT7120 | 250-680-960 | 0.50-1.20-3.50 | 0.05-0.10-0.30 |
| 未处理HB60-90 | GNT7120 | 950-1300-2000 | 0.50-1.20-3.50 | 0.05-0.10-0.3 0 | |||||
小零件车削刀具
小零件车削刀片一览表
小零件车削用刀片(负型)
| 槽型 | 特点 | 加工范围 | 槽型截面 | |
| P | ·斜槽设计，稳定控制切屑的移除方向。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| G | ·圆弧槽设计，提高刀刃锋利性，同时保证刀 尖强度。 ·大刃长设计，满足较大切深。 |  |  | |
| S | ·无刃宽设计，刃口锋利，有效降低切削力。 | 0 0.05 0.1 0.15 0.2 0.25 0.3 f [mm/rev] |  | |
| AK | ·锋利刃设计，满足良好的加工表面质量要 ·刃倾角设计，控制切屑流向，降低切削阻 | ap [mm] 4 3 2 1 0 0.05 0.1 0.15 f[mm/rev. |  |
| 80°菱形 | 55°菱形 | 90°正方形 | 60°正三角形 | 35°菱形 | 80°六边形 | |
 | ||||||
| TNGG-P | ||||||
| P080 | ||||||
 | ||||||
| TNGG-G | ||||||
| P080 | ||||||
 | ||||||
| TNGG-S | ||||||
| P080 | ||||||
 | ||||||
| TNGG-AK | ||||||
| P080 |
小零件车削刀片一览表
小零件车削用刀片(正型)
5°后角
| 槽型 | 特点 | 加工范围 | 槽型截面 | |
| P | ·斜槽设计，稳定控制切屑的移除方向。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| G | ·圆弧槽设计，提高刀刃锋利性，同时保证刀 尖强度。 ·大刃长设计，满足较大切深。 |  |  | |
| S | ·刃倾角设计，控制切屑流向，降低切削阻 力。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| AF | ·小槽宽设计，满足微小切深领域的断屑要求。 ·大前角设计，减少切削阻力，获得优异的加工 表面质量。 |  ap [mm] |  | |
| BF | ·特殊断屑台设计，促进切屑卷曲，利于排 屑。 ·小前角设计，刀尖强度高，通用性强。 | 3 2 0.05 0.1 | 0.15 f[m/rev] |  |
| SK | ·锋利刃及刃倾角设计，提升刃口锋利，有效 降低切削力。 ·全新断屑槽设计,提升小切深钢、不锈钢加工 断屑能力。 |  |  | |
| BK | ·大槽宽设计，排屑顺畅，实现稳定加工。 ·刃倾角设计，控制切屑流向，降低切削阻 力。 |  |  | |
| MM | ·双前角设计，兼顾锋利性和强度，加工范围 广。 ·双曲面断屑台设计，促进稳定卷屑，断屑、 排屑优异。 | ap [mm] 4 3 2 0.05 0.1 0.15 f[mm/rev] |  |
| 80°菱形 | 55°菱形 | 90°正方形 | 60°正三角形 | 35°菱形 | 80°六边形 | |
 |  | |||||
| TBGT-P | VBGT-P | WBGT-P | ||||
| P088 | P091 | P096 | ||||
 | ||||||
| VBGT-G | ||||||
| P091 | ||||||
 | ||||||
| VBGT-S | ||||||
| P092 | ||||||
 | ||||||
| VBGT-AF | ||||||
| P092 | ||||||
 | ||||||
| VBGT-BF | ||||||
| P092 | ||||||
 | ||||||
| VBGT-SK | ||||||
| P092 | ||||||
 | ||||||
| VBGT-BK | ||||||
| P092 | ||||||
 | ||||||
| VBGT-MM | ||||||
| P092 |
小零件车削刀片一览表
小零件车削用刀片（正型)
7°后角
| 槽型 | 特点 | 加工范围 | 槽型截面 | |
| P | ·斜槽设计，稳定控制切屑的移除方向。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| G | ·圆弧槽设计，提高刀刃锋利性，同时保证刀 尖强度。 ·大刃长设计，满足较大切深。 | ap [mm] 3 2.5 2 1.5 0.5 0 0.05 0.1 0.15 0.2 0.25 0.3 f[mm/rev] |  | |
| S | ·刃倾角设计，控制切屑流向，降低切削阻 力。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| AF | ·小槽宽设计，满足微小切深领域的断屑要 求。 ·大前角设计，减少切削阻力，获得优异的加 工表面质量。 | ap [mm] 4 3 2 0 0.05 0.1 0.15 f[mm/rev] |  | |
| AK | ·锋利刃设计，满足良好的加工表面质量要 求。 ·刃倾角设计，控制切屑流向，降低切削阻 力。 | ap [mm] 4 3 2 1 0.05 0.1 0.15 f[mm/rev] 0 |  |
80°菱形 | 55°菱形 | 90°正方形 | 60°正三角形 | 35°菱形 | 80°六边形 | |
 |  |  | ||||
| CGT-P | DCGT-P | TCGT-P | VCGT-P | |||
| P085 | P089 | P093 | ||||
 |  |  | ||||
| CCGT-G | DCGT-G | TCGT-G | VCGT-G | |||
| P082 | P086 | P089 | P093 | |||
 |  | |||||
| DCGT-S | VCGT-S | |||||
| P086 | P093 | |||||
 |  | |||||
| DCGT-AF | VCGT-AF | |||||
| P086 | P093 | |||||
 | ||||||
| DCGT-AK | ||||||
| P087 | ||||||
小零件车削刀片一览表
小零件车削用刀片（正型)
7°后角
| 槽型 | 特点 | 加工范围 | 槽型截面 | ||
| BF | ·特殊断屑台设计，促进切屑卷曲，利于排 屑。 ·小前角设计，刀尖强度高，通用性强。 | ap [mm] 4 3 2 1 0.05 0 | 0.1 0.15 f[mm/rev] |  | |
| SK | ·锋利刃及刃倾角设计，提升刃口锋利，有效 降低切削力。 ·全新断屑槽设计,提升小切深钢、不锈钢加工 断屑能力。 | ap [mm] 4 3 2 0 0.05 | 0.1 0.15 f[mm/rev] |  | |
| BK | ·大槽宽设计，排屑顺畅，实现稳定加工。 ·刃倾角设计，控制切屑流向，降低切削阻 力。 | ap [mm] 3 2 0 0.05 | 0.1 0.15 f [mm/rev] |  | |
| MM | ·双前角设计，兼顾锋利性和强度，加工范围 广。 ·双曲面断屑台设计，促进稳定卷屑，断屑、 排屑优异。 | ap [mm] 4 3 2 0.05 0.1 0 | 0.15 f [mm/rev] |  |
| 80°菱形 | 55°菱形 | 90°正方形 | 60°正三角形 | 35°菱形 | 80°六边形 | |
 |  |  | ||||
| CCGT-BF | DCGT-BF | VCGT-BF | ||||
| P084 | P087 | P094 | ||||
 | ||||||
| DCGT-SK | ||||||
| P087 | ||||||
 |  |  | ||||
| CCGT-BK | DCGT-BK | VCGT-BK | ||||
| P084 | P087 | P094 | ||||
 |  | |||||
| DCGT-MM | VCGT-MM | |||||
| P087 | P094 |
小零件车削刀片一览表
小零件车削用刀片(正型)
11°后角
| 槽型 | 特点 | 加工范围 | 槽型截面 | |
| P | ·斜槽设计，稳定控制切屑的移除方向。 ·无刃宽设计，刃口锋利，有效降低切削力。 |  |  | |
| G | ·圆弧槽设计，提高刀刃锋利性，同时保证刀 尖强度。 ·大刃长设计，满足较大切深。 | ap [mm] 3 2.5 2 1.5 0.5 0 0.05 0.1 0.15 0.2 0.25 0.3 f[mm/rev] ap [mm] |  | |
| BK | ·大槽宽设计，排屑顺畅，实现稳定加工 ·刃倾角设计，控制切屑流向，降低切削阻力 | 4 3 2 1 0 0.05 0.1 0.15 f[mm/rev] |  |
| 80°菱形 | 55°菱形 | 90°正方形 | 60°正三角形 | 35°菱形 | 80°六边形 | |
 |  | |||||
| TPGT(H)-P | VPGT-P | |||||
| P090 | P095 | |||||
 |  | |||||
| TPGT-G | VPGT-G | |||||
| P090 | P095 | |||||
 L | ||||||
| VPGT-BK | ||||||
| P095 |
小零件车削刀片一览表
小零件车削用刀片(其他)
背车
| 槽型 | 特点 | 加工范围 | 槽型截面 | ||
| GSAB | ·特殊形状设计，满足背车加工要求。 ·特殊槽型设计，稳定控制切屑流向。 |  |  | ||
| GSTB | ·立装结构设计，装夹牢固,实现稳定切削。 ·斜槽设计，有效控制排屑方向。 | 0.1 | 0.2 f[mm/rev] |  | |
小零件刀具加工示意图
切断加工 (P218)
背车加工(P97)
外径加工
切槽加工 (P218)
螺纹加工(P286)
端面加工
背车加工(P97)
外径加工
切槽加工 (P218)
螺纹加工(P286)
端面加工
外观
GSAB P097
GSTB P098
三维断屑槽及通用开槽型号表示方法
DCGT11T302
(M)
(E)
(R)
刀尖圆弧为负公差
刃口处理
刀片方向
车削刀片(负型)
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
| TNGG160401L-P | 16.5 9.525 4.76 3.81 | 0.1 | ● | |||||||
| TNGG160401R-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.1 | ● | ● | |||
| TNGG160402L-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.2 | ● | ● | |||
| TNGG160402R-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.2 | ● | ● | |||
| TNGG160404L-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ● | ● | ||
| TNGG160404R-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ● | |||
| TNGG160408L-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.8 | O | ● | O | ||
| TNGG160408R-P | 16.5 | 9.525 | 4.76 | 3.81 | 0.8 | O | O | O | ||
| TNGG160404L-G | 16.5 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||
| TNGG160404R-G | 16.5 | 9.525 | 4.76 | 3.81 | 0.4 | |||||
| TNGG160408L-G | 16.5 | 9.525 | 4.76 | 3.81 | 0.8 | ● | ||||
| TNGG160408R-G | 16.5 | 9.525 | 4.76 | 3.81 | 0.8 | |||||
| TNGG160404R-S | 16.5 | 9.525 | 4.76 | 3.81 | 0.4 | ● | ||||
| TNGG160401M-AK | 16.5 | 9.525 | 4.76 | 3.81 | <0.1 | ● | ||||
| TNGG160402M-AK | 16.5 | 9.525 | 4.76 | 3.81 | <0.2 | ● | ||||
| TNGG160404M-AK | 16.5 | 9.525 | 4.76 | 3.81 | <0.4 | O | ● | |||
●标准库存需预定
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | CCGT0301005ML-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.05 | O | O | O | |
| CCGT0301005MR-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.05 | O | O | O | ||
| CCGT030101ML-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.1 | ● | O | ● | ||
| CCGT030101MR-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.1 | O | O | O | ||
| CCGT030102ML-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.2 | ● | O | ● | ||
| CCGT030102MR-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.2 | ● | O | O | ||
| CCGT030104ML-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.4 | ● | O | ● | ||
| CCGT030104MR-P | 4.0 | 3.5 | 1.4 | 1.9 | <0.4 | O | O | O | ||
| CCGT0401005ML-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.05 | O | O | O | ||
| CCGT0401005MR-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.05 | O | O | O | ||
| CCGT040101ML-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.1 | O | O | O | ||
| CCGT040101MR-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.1 | O | O | O | ||
| CCGT040102ML-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.2 | O | ● | |||
| CCGT040102MR-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.2 | ● | O | O | ||
| CCGT040104ML-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.4 | ● | O | ● | ||
| CCGT040104MR-P | 4.8 | 4.3 | 1.8 | 2.3 | <0.4 | ● | O | O | ||
| CCGT0602005ML-P | 6.5 | 6.35 | 2.38 | 2.8 | <0.05 | O | O | O | ||
| CCGT0602005MR-P | 6.5 | 6.35 | 2.38 | 2.8 | <0.05 | O | ● | O | ||
| CCGT060201ML-P | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | ● | ||||
| CCGT060201MR-P | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | O | C | O | ||
| CCGT09T3005ML-P | 9.7 | 9.525 | 3.97 | 4.4 | <0.05 | O | O | O | ||
| CCGT09T3005MR-P | 9.7 | 9.525 | 3.97 | 4.4 | <0.05 | O | ● | O | ||
| CCGT09T301ML-P | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | ||
| CCGT09T301MR-P | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | ||
| CCGT030101L-P | 4.0 | 3.5 | 1.4 | 1.9 | 0.1 | ● | ||||
| CCGT030102L-P | 4.0 | 3.5 | 1.4 | 1.9 | 0.2 | |||||
| CCGT030104L-P | 4.0 | 3.5 | 1.4 | 1.9 | 0.4 | ● | ||||
| CCGT040101L-P | 4.8 | 4.3 | 1.8 | 2.3 | 0.1 | |||||
| CCGT040102L-P | 4.8 | 4.3 | 1.8 | 2.3 | 0.2 | ● | ||||
| CCGT040104L-P | 4.8 | 4.3 | 1.8 | 2.3 | 0.4 | ● | ||||
| CCGT060201L-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| CCGT060201R-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
车削刀片(正型)
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | |||||
| CCGT060202L-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | ||||||||
| CCGT060202R-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | ||||||||
| CCGT060204L-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | ||||||||
 | CCGT060204R-P | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | |||||||
| CCGT09T301L-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | O | |||||||
| CCGT09T301R-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | ● | |||||||
| CCGT09T302L-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | O | |||||||
| CCGT09T302R-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | ||||||||
| CCGT09T304L-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ||||||||
| CCGT09T304R-P | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ||||||||
| CCGT0602005ML-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.05 | ● | O | 0 | |||||
| CCGT0602005MR-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.05 | O | |||||||
| CCGT060201MEL-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | 0 | 0 | 0 | |||||
| CCGT060201MER-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | O | |||||
 | CCGT060201ML-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | |||||
| CCGT060201MR-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | ||||||
| CCGT060202ML-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.2 | O | O | ||||||
| CCGT060202MR-G | 6.5 | 6.35 | 2.38 | 2.8 | <0.2 | O | O | ||||||
| CCGT09T3005ML-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.05 | O | 0 | ||||||
| CCGT09T3005MR-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.05 | ● | O | ||||||
| CCGT09T301MEL-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | |||||
| CCGT09T301MER-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | |||||
| CCGT09T301ML-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | ||||||
| CCGT09T301MR-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | ● | ● | ● | |||||
| CCGT09T302ML-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.2 | O | O | ||||||
| CCGT09T302MR-G | 9.7 | 9.525 | 3.97 | 4.4 | <0.2 | O | |||||||
●标准库存需预定
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | CCGT060201EL-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | |||
| CCGT060201ER-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| CCGT060201L-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| CCGT060201R-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| CCGT060202EL-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | |||||
| CCGT060202ER-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||||
| CCGT060202L-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | |||||
| CCGT060202R-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.2 | |||||
| CCGT060204EL-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | ● | ||||
| CCGT060204ER-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | |||||
| CCGT060204L-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | O | ||||
| CCGT060204R-G | 6.5 | 6.35 | 2.38 | 2.8 | 0.4 | O | ||||
| CCGT09T301EL-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| CCGT09T301ER-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | ● | ||||
| CCGT09T301L-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| CCGT09T301R-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.1 | ● | ||||
| CCGT09T302EL-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| CCGT09T302ER-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| CCGT09T302L-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | ● | ||||
| CCGT09T302R-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| CCGT09T304EL-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||
| CCGT09T304ER-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | |||||
| CCGT09T304L-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||
| CCGT09T304R-G | 9.7 | 9.525 | 3.97 | 4.4 | 0.4 | O | ||||
●标准库存需预定
车削刀片(正型)
菱形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | CCGT0602005M-BF | 6.5 | 6.35 | 2.38 | 2.8 | <0.05 | ||||
| CCGT060201M-BF | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | |||||
| CCGT060202M-BF | 6.5 | 6.35 | 2.38 | 2.8 | <0.2 | |||||
| CCGT09T301M-BF | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | ||||
| CCGT09T302M-BF | 9.7 | 9.525 | 3.97 | 4.4 | <0.2 | O | ||||
| CCGT09T304M-BF | 9.7 | 9.525 | 3.97 | 4.4 | <0.4 | |||||
 | CCGT060201M-BK | 6.5 | 6.35 | 2.38 | 2.8 | <0.1 | ||||
| CCGT060202M-BK | 6.5 | 6.35 | 2.38 | 2.8 | <0.2 | ● | ||||
| CCGT09T301M-BK | 9.7 | 9.525 | 3.97 | 4.4 | <0.1 | O | ||||
| CCGT09T302M-BK | 9.7 | 9.525 | 3.97 | 4.4 | <0.2 | ● | ||||
| CCGT09T304M-BK | 9.7 | 9.525 | 3.97 | |||||||
●标准库存需预定
菱形55°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | DCGT0702005ML-P | 7.8 | 6.35 | 2.38 | 2.8 | <0.05 | O | ● | O | |
| DCGT0702005MR-P | 7.8 | 6.35 | 2.38 | 2.8 | <0.05 | O | ● | O | ||
| DCGT070201ML-P | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | O | ||
| DCGT070201MR-P | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | |||
| DCGT070202MR-P | 7.8 | 6.35 | 2.38 | 2.8 | <0.2 | O | ||||
| DCGT11T3005ML-P | 11.6 | 9.525 | 3.97 | 4.4 | <0.05 | O | O | O | ||
| DCGT11T3005MR-P | 11.6 | 9.525 | 3.97 | 4.4 | <0.05 | O | ● | O | ||
| DCGT11T302MR-P | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | O | ● | ||
| DCGT0702003L-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.03 | O | ||||
| DCGT0702003R-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.03 | ● | ||||
| DCGT070201L-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| DCGT070201R-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.1 | |||||
| DCGT070202L-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | O | ||||
| DCGT070202R-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | |||||
| DCGT070204L-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | |||||
| DCGT070204R-P | 7.8 | 6.35 | 2.38 | 2.8 | 0.4 | O | ||||
| DCGT11T3003L-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.03 | O | ||||
| DCGT11T3003R-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.03 | O | ||||
| DCGT11T301L-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | 0 | ||||
| DCGT11T301R-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| DCGT11T302L-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| DCGT11T302R-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| DCGT11T304L-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | |||||
| DCGT11T304R-P | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | O | ||||
●标准库存需预定
菱形55°有孔
订货号  | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
| DCGT0702005ML-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.05 | O | O | O | ||
| DCGT0702005MR-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.05 | ● | ● | O | ||
| DCGT070201MEL-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | ● | ||
| DCGT070201MER-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | ● | ||
| DCGT070201ML-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | O | O | ||
| DCGT070201MR-G | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | ● | O | O | ||
| DCGT11T3005ML-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.05 | O | O | O | ||
| DCGT11T3005MR-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.05 | O | ● | ● | ||
| DCGT11T301MEL-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | ||
| DCGT11T301MER-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | ||
| DCGT11T301ML-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | O | O | ||
| DCGT11T301MR-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | ● | ● | ● | ||
| DCGT11T302MER-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | ||||
| DCGT11T302MR-G | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | O | ||||
| DCGT070201L-G | 7.8 | 6.35 | 2.38 | 2.8 | 0.1 | O | ||||
| DCGT070201R-G | 7.8 | 6.35 | 2.38 | 2.8 | 0.1 | ● | ||||
| DCGT070202L-G | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | O | ||||
| DCGT070202R-G | 7.8 | 6.35 | 2.38 | 2.8 | 0.2 | |||||
| DCGT11T301EL-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| DCGT11T301ER-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| DCGT11T301L-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | ● | ||||
| DCGT11T301R-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.1 | |||||
| DCGT11T302EL-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ● | ||||
| DCGT11T302ER-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| DCGT11T302L-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | ● | ||||
| DCGT11T302R-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.2 | |||||
| DCGT11T304EL-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | O | ||||
| DCGT11T304ER-G | 11.6 | 9.525 | 3.97 | 4.4 | 0.4 | ● | ||||
| DCGT11T302MR-S | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | ● | |||
| DCGT11T304MR-S | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | ● | ||||
●标准库存需预定
菱形55°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | DCGT070201M-AF | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | ● | ● | ||
| DCGT11T301M-AF | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | ● | O | |||
 | DCGT11T301M-AK | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | |||
| DCGT11T302M-AK | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | O | |||
| DCGT11T304M-AK | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | O | ||||
 | DCGT070201M-BF | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | |||
| DCGT070202M-BF | 7.8 | 6.35 | 2.38 | 2.8 | <0.2 | |||||
| DCGT070204M-BF | 7.8 | 6.35 | 2.38 | 2.8 | <0.4 | |||||
| DCGT11T301M-BF | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | ||||
| DCGT11T302M-BF | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | ● | |||
| DCGT11T304M-BF | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | |||||
D | DCGT070201M-BK | 7.8 | 6.35 | 2.38 | 2.8 | <0.1 | O | |||
| CGT070202M-BK | 7.8 | 6.35 | 2.38 | 2.8 | <0.2 | |||||
| DCGT11T301M-BK | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | ||||
| DCGT11T302M-BK | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | ● | ● | |||
| DCGT11T304M-BK | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | |||||
 | DCGT11T301M-SK | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | O | |||
| DCGT11T302M-SK | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | O | ||||
| DCGT11T304M-SK | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | O | ||||
 | DCGT11T301M-MM | 11.6 | 9.525 | 3.97 | 4.4 | <0.1 | ||||
| DCGT11T302M-MM | 11.6 | 9.525 | 3.97 | 4.4 | <0.2 | |||||
| DCGT11T304M-MM | 11.6 | 9.525 | 3.97 | 4.4 | <0.4 | |||||
●标准库存需预定
车削刀片(正型)
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | |
TBGT060102L-PTBGT060104L-P F | 6.9 | 3.97 | 1.59 | 2.3 | 0.2 | ||||
| 6.9 | 3.97 | 1.59 | 2.3 | 0.4 | |||||
●标准库存需预定
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | TCGT060102L-P | 6.9 | 3.97 | 1.59 | 2.3 | 0.2 | ||||
| TCGT060104L-P | 6.9 | 3.97 | 1.59 | 2.3 | 0.4 | ● | ||||
| TCGT06T102L-P | 6.9 | 3.97 | 1.98 | 2.3 | 0.2 | 0 | O | O | ||
| TCGT06T102R-P | 6.9 | 3.97 | 1.98 | 2.3 | 0.2 | O | O | O | ||
| TCGT06T104L-P | 6.9 | 3.97 | 1.98 | 2.3 | 0.4 | 0 | O | O | ||
| TCGT06T104R-P | 6.9 | 3.97 | 1.98 | 2.3 | 0.4 | O | O | O | ||
| V | TCGT080202L-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.2 | ● | |||
| TCGT080204L-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.4 | ● | ||||
| TCGT110202L-P | 11 | 6.35 | 2.38 | 2.8 | 0.2 | ● | ||||
| TCGT110204L-P | 11 | 6.35 | 2.38 | 2.8 | 0.4 | |||||
 | TCGT0802005ML-G | 8.2 | 4.76 | 2.38 | 2.3 | <0.05 | O | O | O | |
| TCGT0802005MR-G | 8.2 | 4.76 | 2.38 | 2.3 | <0.05 | O | O | O | ||
| TCGT080201ML-G | 8.2 | 4.76 | 2.38 | 2.3 | <0.1 | O | O | O | ||
| TCGT080201MR-G | 8.2 | 4.76 | 2.38 | 2.3 | <0.1 | O | O | O | ||
| TCGT1103005ML-G | 11 | 6.35 | 3.18 | 2.8 | <0.05 | O | ● | O | ||
| TCGT1103005MR-G | 11 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | |||
| TCGT080202L-G | 8.2 | 4.76 | 2.38 | 2.3 | 0.2 | O | ||||
| TCGT080204L-G | 8.2 | 4.76 | 2.38 | 2.3 | 0.4 | O | ||||
| TCGT110301L-G | 11 | 6.35 | 3.18 | 2.8 | 0.1 | 0 | ||||
| TCGT110302L-G | 11 | 6.35 | 3.18 | 2.8 | 0.2 | O | ||||
| TCGT110304L-G | 11 | 6.35 | 3.18 | 2.8 | 0.4 | O | ||||
●标准库存需预定
车削刀片(正型)
三角形60°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
| TPGH1103005ML-P | 11 | 6.35 | 3.18 | 3.4 | <0.05 | ● | O | |||
| TPGH090202L-P | 9.6 | 5.56 | 2.38 | 3.0 | 0.2 | |||||
| TPGH090204L-P | 9.6 | 5.56 | 2.38 | 3.0 | 0.4 | |||||
| TPGH110301L-P | 11 | 6.35 | 3.18 | 3.4 | 0.1 | |||||
| TPGH110302L-P | 11 | 6.35 | 3.18 | 3.4 | 0.2 | |||||
| TPGH110304L-P | 11 | 6.35 | 3.18 | 3.4 | 0.4 | |||||
| TPGT080202L-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.2 | |||||
| TPGT080202R-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.2 | O | ||||
| TPGT080204L-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.4 | O | ● | |||
| TPGT080204R-P | 8.2 | 4.76 | 2.38 | 2.3 | 0.4 | O | ||||
| TPGT080201L-G | 8.2 | 4.76 | 2.38 | 2.3 | 0.1 | O | ||||
| TPGT080202L-G | 8.2 | 4.76 | 2.38 | 2.3 | 0.2 | O | ||||
| TPGT080204L-G | 8.2 | 4.76 | 2.38 | 2.3 | 0.4 | O | ||||
●标准库存需预定
菱形35°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | |||||
| VBGT1103005ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | |||||
| VBGT1103005MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | ● | ● | ||||||
| VBGT110301ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | ● | O | ||||||
| VBGT110301MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | ● | O | ||||||
| VBGT110302ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | O | O | ● | |||||
| VBGT110302MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | O | ||||||
| VBGT1103003L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | O | |||||||
| VBGT1103003R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | ● | |||||||
| VBGT110301L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ||||||||
| VBGT110301R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ● | |||||||
| VBGT110302L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | ● | |||||||
| VBGT110302R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | ||||||||
| VBGT110304L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | O | |||||||
| VBGT110304R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ||||||||
 | VBGT1103005ML-G | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | |||||
| VBGT1103005MR-G | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | ● | ● | ||||||
| VBGT110301L-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ||||||||
| VBGT110301R-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ||||||||
| VBGT110302EL-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | |||||||
| VBGT110302ER-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | |||||||
| VBGT110302R-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | |||||||
| VBGT110304EL-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ||||||||
| VBGT110304ER-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ||||||||
●标准库存需预定
车削刀片(正型)
菱形35°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
 | VBGT1103005ML-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | |
| VBGT1103005MR-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | ● | ● | ● | ||
| VBGT110301ML-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | O | |||
| VBGT110301MR-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | ● | O | ● | ||
| VBGT110302ML-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | O | C | |||
| VBGT110302MR-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | O | |||
| VBGT110301L-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ● | ||||
| VBGT110301R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | O | ● | O | ||
| VBGT110302L-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | |||||
| VBGT110302R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | |||||
| VBGT110304L-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | O | ||||
| VBGT110304R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | ● | ||||
| VBGT160402L-S | 16.6 | 9.525 | 4.76 | 4.4 | 0.2 | |||||
| VBGT160402R-S | 16.6 | 9.525 | 4.76 | 4.4 | 0.2 | |||||
| VBGT160404L-S | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | ● | ||||
| VBGT160404R-S | 16.6 | 9.525 | 4.76 | 4.4 | 0.4 | |||||
 | VBGT110301M-AF | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | ● | ||
 | VBGT110301M-BF | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | |||
| VBGT110302M-BF | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | C | |||
 | VBGT110301M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | ● | O | ||
| VBGT110302M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | O | ||||
| VBGT110304M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.4 | ● | ● | |||
 | VBGT110301M-SK | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | 0 | |||
| VBGT110302M-SK | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | 0 | ||||
| VBGT110304M-SK | 11.2 | 6.35 | 3.18 | 2.8 | <0.4 | 0 | ||||
 | VBGT110302M-MM | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | O | ||
| VBGT110304M-MM | 11.2 | 6.35 | 3.18 | 2.8 | <0.4 | ● | ||||
●标准库存需预定
菱形35°有孔
订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||||||
| VCGT1103005ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||||||
| VCGT1103005MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||||||
| VCGT110301ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | 0 | O | ||||||
| VCGT110301MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | O | ● | ||||||
| VCGT1103003L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | 0 | ||||||||
| VCGT1103003R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | O | ||||||||
| VCGT110301L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | O | ||||||||
| VCGT110301R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | O | ||||||||
| VCGT110302L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | ||||||||
| VCGT110302R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | ● | ||||||||
| VCGT110304L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | O | ||||||||
| VCGT110304R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.4 | O | ||||||||
 | VCGT1103005MR-G | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | ● | ● | ● | |||||
| VCGT110302R-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | ||||||||
| VCGT1103005ML-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | ● | ||||||
| VCGT1103005MR-S | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||||||
| VCGT1103003R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | O | ||||||||
 | VCGT110301L-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ||||||||
| V | VCGT110301R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ||||||||
| CGT110302L-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | O | ||||||||
| VCGT110302R-S | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | |||||||||
●标准库存需预定
车削刀片(正型)
菱形35°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | |||
 | VCGT110301M-AF | 11.2 6.35 | 3.18 | 2.8 | <0.1 | O | |||||
 | VCGT080202M-BF | 8.3 | 4.76 | 2.38 | 2.3 | <0.2 | ● | ||||
| VCGT110301M-BF | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | ● | ||||
| VCGT110302M-BF | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | ● | ||||
 | VCGT110301M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | ||||
| VCGT110302M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | ● | ● | |||
| VCGT110304M-BK | 11.2 | 6.35 | 3.18 | 2.8 | <0.4 | ● | |||||
 | VCGT110302M-MM | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | |||||
| VCGT110304M-MM | 11.2 | 6.35 | 3.18 | 2.8 | <0.4 | ● | ● | ||||
●标准库存需预定
菱形35°有孔
订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
| VPGT1103005ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||
| VPGT1103005MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | ● | O | O | ||
| VPGT110301ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | O | O | O | ||
| VPGT110301MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.1 | ● | ● | ● | ||
| VPGT110302ML-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | O | O | O | ||
| VPGT110302MR-P | 11.2 | 6.35 | 3.18 | 2.8 | <0.2 | ● | O | ● | ||
| VPGT1103003L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | O | ||||
| VPGT1103003R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.03 | O | ||||
| VPGT110301L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | O | ||||
| VPGT110301R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | |||||
| VPGT110302L-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | |||||
| VPGT110302R-P | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | |||||
| VPGT1103005ML-G | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||
| VPGT1103005MR-G | 11.2 | 6.35 | 3.18 | 2.8 | <0.05 | O | O | O | ||
 | VPGT110301L-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | O | |||
| VPGT110301R-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.1 | ● | ||||
| VPGT110302R-G | 11.2 | 6.35 | 3.18 | 2.8 | 0.2 | ● | ● | |||
 | VPGT080201M-BK | 8.3 | 4.76 | 2.38 | 2.3 | <0.1 | O | O | ||
| VPGT080202M-BK | 8.3 | 4.76 | 2.38 | 2.3 | <0.2 | O | O | |||
●标准库存需预定
车削刀片(正型)
六边形80°有孔
| 订货号 | 尺寸(mm) | 涂层硬质合金 | ||||||||
| LE | IC | S | D1 | RE | GAT7115 | GAT7120 | GAT7120A | GAT7125 | ||
WBGT020101L-P | 2.5 | 3.97 | 1.59 2.3 | 0.1 | ||||||
| WBGT020102L-P | 2.5 | 3.97 | 1.59 | 2.3 | 0.2 | O | ● | O | ||
| WBGT020104L-P | 2.5 | 3.97 | 1.59 | 2.3 | 0.4 | O | ● | |||
| WBGTL30202L-P | 3.2 | 4.76 | 2.38 | 2.3 | 0.2 | O | ||||
| WBGTL30204L-P | 3.2 | 4.76 | 2.38 | 2.3 | 0.4 | O | ||||
●标准库存需预定
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||||||||
| A | B | C | D | H | L | R | S | 01 | 02 | GAT115 | GAT120 | GAT0A | GAT125 | ||
| GSAB15R4025005 | 2.8 | 7.0 | 0.4 | 3.4 | 4.3 | 15.5 | 0.05 | 3.97 | 15° | 30° | ● | ● | ● | ||
| GSAB15R4025005M | 2.8 | 7.0 | 0.4 | 3.4 | 4.3 | 15.5& | lt;0.05 | 3.97 | 15° | 30° | ● | ● | ● | ||
| GSAB15R4025015 | 2.8 | 7.0 | 0.4 | 3.4 | 4.2 | 15.4 | 0.15 | 3.97 | 15° | 30° | ● | ● | |||
| GSAB15R4025015M | 2.8 | 7.0 | 0.4 | 3.4 | 4.2 | 15.4& | lt;0.15 | 3.97 | 15° | 30° | ● | ● | ● | ||
| GSAB15R4045005 | 4.7 | 7.0 | 0.65 | 3.4 | 4.3 | 15.5 | 0.05 | 3.97 | 15° | 45° | O | ● | O | ||
| GSAB15R4045005M | 4.7 | 7.0 | 0.65 | 3.4 | 4.3 | 15.5& | lt;0.05 | 3.97 | 15° | 45° | O | O | |||
| GSAB15R4045015 | 4.7 | 7.0 | 0.65 | 3.4 | 4.2 | 15.4 | 0.15 | 3.97 | 15° | 45° | ● | ● | O | ||
| GSAB15R4045015M | 4.7 | 7.0 | 0.65 | 3.4 | 4.2 | 15.4& | lt;0.15 | 3.97 | 15° | 45° | ● | ● | O | ||
| GSAB23R5045005 | 4.7 | 7.0 | 0.55 | 3.4 | 5.3 | 23.5 | 0.05 | 3.97 | 15° | 40° | O | ● | O | ||
| GSAB23R5045005M | 4.7 | 7.0 | 0.55 | 3.4 | 5.3 | 23.5& | lt;0.05 | 3.97 | 15° | 40° | O | ● | O | ||
| GSAB23R5045015 | 4.7 | 7.0 | 0.55 | 3.4 | 5.2 | 23.4 | 0.15 | 3.97 | 15° | 40° | ● | ● | |||
| GSAB23R5045015M | 4.7 | 7.0 | 0.55 | 3.4 | 5.2 | 23.4& | lt;0.15 | 3.97 | 15° | 40° | ● | ● | O | ||
●标准库存需预定
背车型号表示方法
GSAB 15
40
25
015
(M)
系列代号-平装背车
刀片大小
刀片方向
最大切深
切削刃宽
刀尖圆弧
刀尖圆弧为负公差
背车刀片
GSTB□□
立装背车刀片
| 订货号 | 尺寸(mm) | 涂层硬质合金 | |||||||||||
| CW | CDX | a | Θ | RE | D1 | W1 | S | GAT7115 | GAT7120 | GAT0A | GAT25 | ||
 | GSTB3R15005M | 1.5 | 2.7 | 0.25 | 56° | <0.05 | 5.2 | 3.0 | 8.7 | ● | ● | O | |
| GSTB3R15010M | 1.5 | 2.7 | 0.25 | 56° | <0.10 | 5.2 | 3.0 | 8.7 | O | ● | O | ||
| GSTB3R28005M | 2.8 | 4.6 | 0.3 | 56° | <0.05 | 5.2 | 3.0 | 8.7 | ● | O | O | ||
| GSTB3R28010M | 2.8 | 4.6 | 0.3 | 56° | <0.10 | 5.2 | 3.0 | 8.7 | ● | ● | O | ||
| GSTB3R28020 | 2.8 | 4.6 | 0.5 | 56° | 0.20 | 5.2 | 3.0 | 8.7 | O | O | |||
| GSTB4R38005M | 3.8 | 6.3 | 0.3 | 56° | <0.05 | 5.2 | 4.0 | 9.5 | ● | O | O | ||
| GSTB4R38010M | 3.8 | 6.3 | 0.3 | 56° | <0.10 | 5.2 | 4.0 | 9.5 | ● | O | O | ||
| GSTB4R38020M | 3.8 | 6.3 | 0.5 | 56° | <0.20 | 5.2 | 4.0 | 9.5 | O | O | |||
●标准库存需预定
GSTB
3
R
28
015
(M)
系列代号-立装背车
刀片大小
刀片方向
切削刃宽
刀尖圆弧
刀尖圆弧为负公差
