该页无缩略图
5 将滑槽组件装于门板上，安装参数如下，或按照定位纸进行打孔。
Mount the slide slot component onto the door panel.
The installation parameters are as follows,or make holes according to the positioning paper.
安装参数：L值随盖位和K值变化，具体参照下表；H=T+9+h，T为顶板厚度，h为门板顶部与顶板顶部的高度差；
(注：如门板顶部与顶板顶部平齐，则h=0； 如门板高于顶板则h为正数；如门板低于顶板 则h为负数)
Installation parameters: The L value varies with the cover position and K value. Please refer to the following table for details; H = T + 9 + h, where T is the thickness of the roof panel, and h is the height difference between the top of the door panel and the top of the roof panel; (Note: If the top of the door panel is level with the top of the roof panel, then h = 0; If the door panel is higher than the roof panel, then h is a positive number; if the door panel is lower than the roof panel, then h is a negative number
| L overlay盖位K值 | 16 | 17 | 18 | 19 | 20 |
| 3 | 80 | 81 | 82 | 83 | 84 |
| 4 | 81 | 82 | 83 | 84 | 85 |
| 5 | 82 | 83 | 84 | 85 | 86 |
将推杆释放至完全打开状态，检验滑槽与推杆是否呈相对平行状态。按照参数表将M4×14盘头木螺丝打入木板进行安装（注：推杆释放过程中，需按警告标贴提示操作）
Release the push rod to the fully open position,
Check if the slide groove and the push rod are in a relatively parallel state. Insert the M4x14 hexagonal wood screws according to the parameter table into the wooden board for installation.
(Notes: During the release process of the push rod,
please follow the instructions on the warning labels.)
7 将推杆尾端放入滑槽组件，并按下图将滑块推至扣合状态
Insert the tail end of the push rod into the sliding slot component, and push the slider to the locked position as shown in the figure.
将滑槽盖沿着箭头方向推入滑槽进行安装
9 使用开门器正常触发开合数个回合，检查功能是否正常。
Use the door opener to trigger the opening and closing several rounds normally,and check if the function is working properly. (此过程可根据灵敏度或门缝需求适当调整触发螺钉伸出长度)
Push the slide cover into the slide groove in the direction indicated by the arrow for installation.
10 确认功能正常后，将螺钉拧入一圈，后将螺钉盖沿箭头方向推入，盖住螺钉。
After confirming that the function is normal, screw the screws into a circle, then push the screw cap along the arrow direction to cover the screws.
产品应用搭配推荐轻型：选配2只铰链重型:选配≤3\~6只铰链本产品适用于液压铰链使用。
注意事项:
1、请勿将传动推杆面对人体要害部位，避免触发反弹推动杆造成伤害。
2、请勿随意拆卸本产品，避免触发内部零件弹出
This product is applicable to hydraulic hinge
Matters needing attention:
1. Do not face the push rod to the key part of the human body to avoid triggering bounce the push rod to cause damage.
2. Do not disassemble the product at will to avoid triggering the ejection of internal parts
产品功能简介 PRODUCT FUNCTION INTRODUCTION
选用门板规格 SPECIFICATION OF SELECTED DOOR PLATE
功能介绍：
1、本产品轻触即开，以500MM宽门板为例打开距离为50MM
2、关闭门板前，至少需60°复位角度
3、本产品轻轻按开启推缓冲复位。
Function introduction: 1. This product can be opened with a light touch. Take the 500mm wide door panel as an example the opening distance is 30-40mm 2. Before closing the door panel, at least 60 ° reset angle is required 3. This product can be reset by gently pressing the open push buffer.
| 产品种类Product category | 承重Bearing | 门板规格(推荐)Door panel specification | |
| 轻型 Light | ≤ 7.5kg | ≤ 700(H)×600(W)mm | |
| 重型Heavy duty | 门Wooden doors | ≤ 20kg | ≤ 2700(H)×600(W)mm |
| 铝框门Aluminum frame door | ≤ 25kg | ||
F8835飞机反弹器 Airplane reboiler
F8837K锁扣反弹器 Lock rebound device
KITCHEN STORAGE SERIES
星烨 厨房收纳系列
为满足最高要求而打造的储物柜，让厨房使用者一见倾心。实用的内抽不仅能提供大量的收纳空间，而且方便使用者拿取物品。在长度、宽度和深度的设计上也十分灵活。提供高柜、中高柜、地柜和吊柜等收纳解决方案，完美利用空间
The storage cabinets specially designed to meet the highest standards will captivate anyone who sees them. The practical internal drawers not only offer ample storage space but also make it convenient for users to access items. The design in terms of length, width, and depth is also highly flexible. They provide various storage solutions such as high cabinets, mid-high cabinets, floor cabinets, and hanging cabinets, effectively making full use of space.
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
星烨·高柜阻尼联动篮
XINGYE· High Counter Damping Linked Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE:WxDxHmm | 描述 DESCRIBE | 承重 BEARING | |
| 450柜 | 380x530x(1650-1850) | 5层 | 总承重65-70KGS 每层承重3-5KGS | |
| 600柜 | 530x530x(1650-1850) | 5层 | 总承重65-70KGS 每层承重3-5KGS | |
| 450柜 | 380x530x(1950-2150) | 6层 | 总承重65-70KGS 每层承重3-5KGS | |
| 600柜 | 530x530x(1950-2150) | 6层 | 总承重65-70KGS 每层承重3-5KGS |
XINGYE· Damping High Extension Pull Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 描述 DESCRIBE | 承重 BEARING |
| 200柜 | 150x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 300柜 | 250x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 400柜 | 350x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 200柜 | 150x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
| 300柜 | 250x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
| 400柜 | 350x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
XINGYE· Corner Damping Fully Open - Small Monster
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE:WxDxHmm | 承重 |
| BEARING | ||
| 800柜-900柜(不分左右) | 620x462x585 | 25-30 KGS |
XINGYE· Suspension Cabinet Damping Elevator
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 564x260x542 | 30KGS |
| 700柜 | 664x260x542 | 30KGS |
| 800柜 | 764x260x542 | 30KGS |
| 900柜 | 864x260x542 | 30KGS |
KITCHENSTORAGE SERIES星烨厨房收纳系列
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
星烨·三边碗碟篮
XINGYE·Three-Sided Dish and Bowl Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x105 | 25KGS |
| 700柜 | 650x430x105 | 25KGS |
| 750柜 | 700x430x105 | 25KGS |
| 800柜 | 750x430x105 | 25KGS |
| 900柜 | 850x430x105 | 25KGS |
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
星烨·三边锅具篮
XINGYE· Three-Sided Cookware Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x105 | 25KGS |
| 700柜 | 650x430x105 | 25KGS |
| 750柜 | 700x430x105 | 25KGS |
| 800柜 | 750x430x105 | 25KGS |
| 900柜 | 850x430x105 | 25KGS |
KITCHEN STORAGE SERIES
星烨·三层抽中抽
KITCHEN STORAGE
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
XINGYE· Third Floor – Lottery Draw – Knife Fork Tools Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x105 | 25KGS |
| 700柜 | 650x430x105 | 25KGS |
| 750柜 | 700x430x105 | 25KGS |
| 800柜 | 750x430x105 | 25KGS |
| 900柜 | 850x430x105 | 25KGS |
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
星烨·三层抽中抽碗碟篮/锅具篮
XINGYE· Third Floor Prize Draw Tray/Dish Basket/Burner Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x105 | 25KGS |
| 700柜 | 650x430x105 | 25KGS |
| 750柜 | 700x430x105 | 25KGS |
| 800柜 | 750x430x105 | 25KGS |
| 900柜 | 850x430x105 | 25KGS |
KITCHEN STORAGE
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
星烨·多功能调味篮
XINGYE· Multi-functional Flavor Container
| 柜体(mm) | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| CABINET | ||
| 300柜 | 250x430x450 | 25KGS |
| 350柜 | 300x430x450 | 25KGS |
| 400柜 | 350x430x450 | 25KGS |
星烨·两层窄篮
XINGYE·Two-layer narrow baskets
| 柜体(mm) | 尺寸(宽×深×高)mm | 承重 |
| CABINET | SIZE:WxDxHmm | BEARING |
| 200柜 | 120x465x450 | 25KGS |
KITCHEN
STORAGE SERIES
星光 厨房收纳系列
SYANUO塞亚诺
全屋定制家居五金
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
Starlight · High Counter Damping Linked Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE:WxDxHmm | 描述 DESCRIBE | 承重 BEARING |
| 450柜 | 380x530x(1650-1850) | 5层 | 总承重65-70KGS 每层承重3-5KGS |
| 600柜 | 530x530x(1650-1850) | 5层 | 总承重65-70KGS 每层承重3-5KGS |
| 450柜 | 380x530x(1950-2150) | 6层 | 总承重65-70KGS 每层承重3-5KGS |
| 600柜 | 530x530x(1950-2150) | 6层 | 总承重65-70KGS 每层承重3-5KGS |
Starlight· Damping High Stretch Basketball
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 描述 DESCRIBE | 承重 BEARING |
| 200柜 | 150x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 300柜 | 250x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 400柜 | 350x505x(1659-1955) | 5层 | 总承重75-80KGS 每层承重5KGS |
| 200柜 | 150x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
| 300柜 | 250x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
| 400柜 | 350x505x(1959-2255) | 6层 | 总承重75-80KGS 每层承重5KGS |
Starlight · Corner Damping Fully Activated Mini Monster
| 柜体(mm) | 尺寸(宽×深×高)mm | 承重 |
| CABINET | SIZE:WxDxHmm | BEARING |
| 800柜-900柜(不分左右) | 620x462x585 | 25-30 KGS |
Starlight · Hanging Cabinet Damping Elevator
| 承重 | ||
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE:WxDxHmm | BEARING |
| 600柜 | 564x260x542 | 30KGS |
| 700柜 | 664x260x542 | 30KGS |
| 800柜 | 764x260x542 | 30KGS |
| 900柜 | 864x260x542 | 30KGS |
SYANUO®塞亚诺全屋定制家居五金
KITCHEN STORAGE SERIES
星光 厨房收纳系列
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
KITCHEN STORAGE
Starlight· All-Aluminum Glass Dishes and Bowls Basket
| 柜体(mm) | 尺寸(宽×深×高)mm | 承重 |
| CABINET | SIZE:WxDxHmm | BEARING |
| 600柜 | 550x430x140 | 25KGS |
| 700柜 | 650x430x140 | 25KGS |
| 750柜 | 700x430x140 | 25KGS |
| 800柜 | 750x430x140 | 25KGS |
| 900柜 | 850x430x140 | 25KGS |
KITCHEN STORAGE
Starlight · All-Aluminum Glass Cookware Basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x140 | 25KGS |
| 700柜 | 650x430x140 | 25KGS |
| 750柜 | 700x430x140 | 25KGS |
| 800柜 | 750x430x140 | 25KGS |
| 900柜 | 850x430x140 | 25KGS |
SYANUO 塞亚诺全屋定制家居五金
KITCHEN STORAGE SERIES
星光·三层抽中抽
星光·三层抽中抽刀叉碗碟篮
Starlight · Three-layer drawer with knife, fork, bowl, plate and basket
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE:WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x205 | 25KGS |
| 700柜 | 650x430x205 | 25KGS |
| 750柜 | 700x430x205 | 25KGS |
| 800柜 | 750x430x205 | 25KGS |
| 900柜 | 850x430x205 | 25KGS |
KEY INTRODUCTION TO THE KITCHEN SUPPORTING HARDWARE FUNCTIONAL SYSTEM
Starlight · Three-layer draw basket for cookware
| 柜体(mm) CABINET | 尺寸(宽×深×高)mm SIZE：WxDxHmm | 承重 BEARING |
| 600柜 | 550x430x140 | 25KGS |
| 700柜 | 650x430x140 | 25KGS |
| 750柜 | 700x430x140 | 25KGS |
| 800柜 | 750x430x140 | 25KGS |
| 900柜 | 850x430x140 | 25KGS |
