CC 2400-1 – serial no. 43026 1150 Page 8 of 10

Notes on Crane Operation according to

DIN 15019.2 / EN 13000, Hoisting Class H1, Power Plant Group 1Bm

1150, SG/cs 23.07.07 znfx-e13b2da866544dc3863a635d58e626a2.doc

11.0 Driving with load and without load

♦ General:

Driving without load:

 In case of driving without load the boom angles have to be set according to the parking regulations.

Driving with load:

 The crane can be driven with a load in any boom combination.

 When driving with load, the capacity charts apply.

 Loads should always be driven at the minimum possible radius and near to the ground.

 When driving with a load, speed range 1 must always be selected. Changes in the direction of

travel should be made as slowly as possible.

 The load must always be prevented from swinging to and fro (it should be lashed if necessary).

 The ground must be even and capable of bearing weight (see soil pressure values).

 Driving with a load is permissible up to a max. wind speed of 9.8 m/s.

 Lower wind speed values on the corresponding capacity charts must be observed.

Operating mode Configuration perm. Inclination Conditions/Restrictions

Driving without load

Boom along longitudinal

crawler axis

HA + HI  72m  10° on the whole

 3° diagonally

- boom slope sided

- no restriction of travelling road

HA + HI > 72m  5° on the whole

 2° diagonally

boom 360° HA + HI  72m  3° on the whole

HA + HI > 72m  2° on the whole

Driving with load on even ground (inclination < 0.3°, max. speed 0.5 km/h)

boom along longitudinal

crawler axis

all lengths  0.3° - no restriction of travelling road

boom 360° all lengths  0.3° - positioning of loads up to a

travelling road of max. 20 m

Driving with load on inclined ground (inclination > 0.3°, max. speed 0.5 km/h)

only main boom 360°

HA  72m  1°

 2°

- reduction of capacity: 20%

- reduction of capacity: 30%

HA > 72m  1° - reduction of capacity: 30%

main boom and jib 360°

HA + HI  72m  1°

 2°

- reduction of capacity: 30%

- reduction of capacity: 40%

HA + HI  108m  1° - reduction of capacity: 40%

HA + HI > 108m  1° - reduction of capacity: 50%

CC 2400-1 – serial no. 43026 1150 Page 9 of 10

Notes on Crane Operation according to

DIN 15019.2 / EN 13000, Hoisting Class H1, Power Plant Group 1Bm

1150, SG/cs 23.07.07 znfx-e13b2da866544dc3863a635d58e626a2.doc

12.0 Notes on Superlift

All capacities with 0t superlift counterweight are defined with unmounted superlift carrier or superlift frame.

Dead weight Superlift-counterweight carrier: 30.0 t incl. connecting cylinder

The Superlift-counterweight carrier with connecting cylinder can be taken into account with 20 t towards the

Superlift-counterweight. 10 t serve as a lifting reserve.

Lifting the Superlift-counterweight carrier is not allowed.

Example: 200t SL-GGW - 20t SL-cwt.-carrier = 180t required ballast on the carrier

13.0 Notes on Runner

There are no capacity charts for Runner. The capacities on the Runner are directly calculated. Runner is

possible on all configurations except all configurations with LF !

With the following formula, the capacity on Runner can be calculated approximately.

CAP CAP UFL 0,5 mWU m 30 t =

H − −  − RUN 

CAPH = capacity ref. chart with load on boom head next to runner

UFL = weight of hook block on boom head next to runner

m WU = mass of jib suspension rods (if lying on main boom)

m RUN = mass of Runner (excluding the hook block on Runner) about 950kg

CC 2400-1 – serial no. 43026 1150 Page 10 of 10

Notes on Crane Operation according to

DIN 15019.2 / EN 13000, Hoisting Class H1, Power Plant Group 1Bm

1150, SG/cs 23.07.07 znfx-e13b2da866544dc3863a635d58e626a2.doc

14.0 Notes on reevings

Reevings stated on the capacity charts correspond to ISO.

For crane operation in the United States of America it is not allowed to exceed the maximum loads given in

the chart below. If necessary, choose a higher reeving.

Reeving Single Double

[kN] [kN]

1 135,0 270,0

2 270,0 540,0

3 405,0 810,0

4 540,0 1 080,0

5 675,0 1 350,0

6 810,0 1 620,0

7 945,0 1 890,0

8 1080,0 2 160,0

9 1215,0 2 430,0

10 1350,0 2 700,0

11 1485,0 2 970,0

12 1620,0 3 240,0

13 1755,0 3 510,0

14 1890,0 3 780,0

15 2025,0 4 050,0

16 2160,0 -

17 2295,0 -

18 2430,0 -

19 2565,0 -

20 2700,0 -

21 2835,0 -

22 2970,0 -

23 3105,0 -