GP-CQP系列B型GG-CQP SERIES B TYPE

●GP-CQP20-D型GP-CQP20-Dtype

技术参数 Technical parameters

●CQP20-D型技术参数 Technical parameters

概述 Overview

GP-CQP系列B型产品广泛应用于起重、运输、冶金、矿山、港口、建筑等机械中各种机构的制动和减速，以及电缆、造纸、钢板等机械的张紧控制领域。

GP-CQP B series products are widely used in lifting, transportation, metallurgy, mining, port construction and other machinery of various institutions of braking and deceleration, and cable, paper, steel and other mechanical tensioning control field.

●使用条件 Use conditions

·环境温度-5℃\~40℃。

·工作气压：≤ 7bar。

·户外雨雪侵蚀或有腐蚀性气体和介质应采用防腐型产品。

• Ambient temperature:-5℃\~40℃.

• Working pressure:≤7bar.

·空气源不应有油，水和其他杂质。 • Air sources there should be no oil, water and other impurities.

• Outdoor rain erosion or corrosive gases and the media should adop anti-corrosion products.

●主要特点 Main Features

·气压制动，弹簧释放。

·整体结构简单，体积小，重量轻。

·无石棉制动衬垫，绿色环保。

·制动衬垫安装、更换方便快捷。

·制动衬垫磨损后调整方便简单。

·所有动力源无需单独设置，可与已有的空压站并网使用，在供气线路中加装调速阀，制动时间可实现无级调整。

·制动块自动随位装置，以确保制动块在整机开合运作状态下与主机制动盘上下间隙均等。

• Air brake, spring release.

• Overall simple structure, small size, light weight.

• Asbestos-free brake pads, green environmental protection.

• Brake pad mounting, convenient and quick replacement

• The brake pad mounting, convenient and quick replacement.

• All the power source without the need for separate setting. with the use of air compressor station in gas supply line in parallel, with speed regulation valve, the braking time and can realize stepless adjustment.

• Brake blocks automatically with the system, to ensure that the brake blocks operation State disc brake with the host machine hermeticclearance equal up and down.

●型号意义Model significance

技术参数 Technical parameters

技术参数见表一，外形尺寸见表二，结构见图一

Technical parameters are shown in table a, the dimensions are shown in table 2, the structure is shown in figure 1

(图一)

●GP-CQP20∥型 GP-CQP20Ⅱ| type

技术参数见表三，外形尺寸见表四，结构见图一

Technical parameters are shown in table 3, the dimensions are shown in table 4, the structure is shown in figure 1

●GP-CQP38∥型GP-CQP38∥type

技术参数见表五，外形尺寸见表六，结构见图一

Technical parameters are shown in table 5, the dimensions are shown in table 6, the structure is shown in figure 1

●GP-CQPL38|系列制动器外形尺寸GP-CQPL38|series actuator dimension

G3/8

注：括号内为GP-CQPL38I-B的尺寸 Note: brackets for the GP-CQPL38 I-B size
●主要技术参数及外形尺寸 The main technical parameters and dimensions一、GP-ADP60M、GP-ADP61M、GP-ADP62M外形

适合盘厚:15或30mm Suitable for thick plate: 15 or 30 mm

GP-ADP系列GG-ADP SERIES

●技术参数及外形尺寸表 Technical parameters and shape dimension table

技术参数见表七，外形尺寸及结构见图二 Technical parameters are shown in table 5, the dimensions are shown in table 2

单位：(mm)

●GP-ADP60M、GP-ADP61M、GP-ADP62M基本参数GP-ADP60M, GP-ADP61M, GP-ADP62M basic parameters

制动力矩(N.m)=制动力/1000×B(B为摩擦半径，单位mm)对“B”尺寸安装与数据，请看ADP60M-ADP61M-ADP62M总装图P=可得到的压力(bar)

适合盘厚:15或30mm Suitable for thick plate: 15 or 30 mm

底板与盘平行时的装配形式 When parallel plate and plate assembly form<br>托架与盘垂直时的装配形式 Bracket with a plate of vertical form of assembly

●对非标准盘，请向技术部咨询 On the non standard disc, please refer to the technical advisory

单位：mm

弹簧制动-气动释放-适合盘厚:15或30mm

Suitable for thick plate: 15 or30 mm

●用途及主要特点 Application And Main Features

·与鼓式制动器相比具有结构紧凑，制动力大、安装方便等优点，它主要用于起重、运输、冶金、矿山、港口、建筑机械、电缆、吊索设备、风力发电机、纺织机械等各行业的多种机械驱动配套的机械制动或减速。

·制动力大,维修费用低,带衬垫磨损自动补偿装置(制动力矩稳定),响应时间短.

·安装允许公差大，制动盘端面跳动，最大值±0.2mm；底座相对于盘的垂直度偏差±0.4%。。

·制动盘相对于底座的中心距偏差，最大值±2.5mm。

GP-SP系列GG-SP SERIES

· Compared with drum brakes, SH series failure protection disc brakes have the advantages of compact structure. braking force, easy installation, it is mainly used for mechanical braking or deceleration of supporting a variety of mechanical drive of lifting, transportation, metallurgy, mining, ports, construction machinery, cable sling equipment, wind turbines, textile machinery and other industries.

· Braking force is big, low maintenance cost, with liner wear self-compensation device (brake torque stability), the response time is short.

· Install the allowed tolerance, brake disc face run out ± 0.2 mm; Base relative to the plate of the verticality deviation of ± 0.4 %.

• Brake disc relative to the base of center distance deviation, maximum plus or minus 2.5 mm.

使用条件 Use conditions

·环境温度；-20℃\~50℃。

·周围环境工作中不得有易燃、易爆气体。

· 空气相对湿度不大于90%。

·使用地点的海拔高度符合GB755-2008.

·户外雨雪侵蚀或有腐蚀性气体和介质应采用防腐型产品。

· Environment temperature; -20℃ -50℃.

. There is no flammable, explosive gas in the ambient.

• Air relative humidity is less than 90%.

· The altitude of the place of use is in accordance with GB755-2008.

· The anti-corrosion products should be used for outdoor rain and snow erosion or corrosive gas and medium .

●根据用户不同的需求,可加装下列设置Application And Main Features

·衬垫磨损显示(通过显示开关或衬垫里的磨损线实现)。

·制动显示(通过显示开关实现)。

·手动释放显示(通过显示开关实现)。

·特殊应用。

·用于盘温非常高时的烧结衬垫,特种衬垫(无火星等)。

·特殊盘(厚度、直径、材料等)。

若有要求，请与我们的技术人员联系。

· Liner wear display (via the display switch or liner wear line).
· Brake show (by display switch).
· Manual release show (by display switch).
· Special applications.
· Used for sintering liner plate when the temperature is very high, special packing (not the Mars, etc.).
· Special dish (thickness, diameter, material, etc.).
If you have requirements, please contact our technical staff.

●主要技术参数及外形尺寸 The main technical parameters and dimensions

ltie e e size

用途 Use conditions

·GP-KPZ型带式输送机用盘式制动装置主要适用于煤矿井下，有防爆要求的露天煤矿、选煤等工作场所，也适用于大型机电设备的可控制动停车，同时适用于各种机电设备的定转场合，制动装置其结构形式为常闭型。

· GP-KPZ type disc brake for belt conveyor device mainly applies to underground coal mine, explosion-proof requirements of workplaces such as openpit coal mine, coal, also applies to the large electromechanical equipment controlled parking, while applicable to all kinds of mechanical and electrical equipment will be transferred, for normally closed brake its structural form.

GP-KPZ系列GG-KPZ SERIES

技术性能 Technical performance

·与电控装置配合，使大型机电设备的停车减速度保持在0.05\~0.03m/S2。

·系统突然断电时，仍能确保大型机电设备平稳地减速停车。

·其结构属于常闭式，停车性能可靠。

·液压控制系统采用双回路结构，一用一备，工作可靠性高。

·环境温度为40℃以下，每小时制动10次，盘面最高温度不高于150℃，并且无火花产生。

· Works with electronic control devices, keep a large parking deceleration of electromechanical equipment in 0.05\~0.03m/S2.

· When the system suddenly loses power, has been able to ensure the smooth deceleration parking for large mechanical and electrical equipment.
· Their structures are often closed, reliable stopping performance.

· Hydraulic control system uses a double-loop structure, high reliability of work

· Below ambient temperature to 40 C, brake 10 times per hour, disc surface temperature is not higher than 150 degrees centigrade, and no spark.

安装方式Installation

·GP-KPZ型带式输送机用盘式制动装置要由盘式制动器、液压系统和电气控制系统组成。根据现场条件，盘式制动器与负载的联接方式有三种方式，如图1所示：

·制动盘与驱动轮采用联轴器方式联接，安装方式(一)。

·制动盘与减速器的某一出轴联接，安装方式(二)。

·制动盘与驱动轮采用胀套联接接，安装方式(三)。

· GP-KPZ type belt conveyor with disc brake for the disc brakes, hydraulic system and electrical control system components. Under field conditions there are disc brakes with load joins in three ways, as shown in Figure 1:
· Brake disc and drive wheel coupling mode joins installation (l).

• Join brake discs an axis reducer installation (Il).

· Join brake disc wheel cover installation (IIl).

适用环境 Environmental Condition

·工作环境温度为-10℃\~+40℃。

·无显著摇摆和剧烈振动、冲击的场合。

·无足以锈蚀金属的气体及尘埃的环境。

·使用地点的海拔高度不超过2000m。

·适合煤矿井下要求防爆的场合。

· Working ambient temperature -10℃ \~ +40℃.
· No significant occasion of rocking and intense vibrations, shocks.
· Sufficient to rusting metal gas and dust-free environment.
· Altitude of the place of use does not exceed 2000m.
· Suitable for requirements under the coal mine explosion-proof occasions.

●型号意义Model significance

型号标注示例

1、制动盘直径为1000mm，两副GP-K丫P—63制动器的制动装置，其标记为GP-KPZ—1000/63。

2、制动盘直径为1600mm，四副GP-K丫P一63制动器的制动装置，其标记为GP-KPZ—1600/4—63。

Type annotation example

1、Brake disc diameter of 1000mm, two kap 163 brake brake, marks it as KPZ-1000/63.

2、Brake disc diameter of 1600mm, four Deputy kap 163 brake brake, marks it as KPZ-1600/4-63.

外形尺寸图Shapedimension figure

图1GP-KPZ型带式输送机用盘式制动装置布置示意图Figure 1 GP-KPZ type belt conveyor with disc brake

·闸瓦与制动盘间的摩擦系数为0.35

·闸瓦间隙：1—1.5mm

· Brake shoe clearance: 1-1.5mm

·制动器数量：2副/4副/6副

·应用于地面设备时，最高允许转速可以提高至500r/min

· Number of brakes: 2/4/6

·GP-KPZ型带式输送机用盘式制动装置外形尺寸参数见表2

• When you apply a dry ground equipment, increase the maximum allowed speed to 500r/min

• GK-KPZ disc brake device for belt conveyor overall dimensions, parameters are shown in table 2

●表2制动装置外形尺寸表 Table 2 brake unit overall dimensions table

单位：(mm）

备注 The remark

·GP-KPZ-1400及其以下规格采用轴承套连接（如图2)，安装方式为图一中(一)、(二)两种方式·GP-KPZ-1600及其以下规格采用胀套连接（如图3)，安装方式为图1中(三）方式·如需其他形式，可根据用户要求针对性设计。

· GK-KPZ - 1400and the following specifications by the bearing sleeve connection ( Figure 2), installation to a (I), (Il) two ways · GK-KPZ - 1600and the following spectfas by the expansion sleeve connection (Figure 3), installation method for Figure 1(IIl) way • If other forms, according to user requirements to design.

外形及连接尺寸 External and connecting dimensions

图2GP-KPZ型带式输送机用盘式制动装置外形及联接尺寸图（轴承座联接型） Figure 2 GP-KPZ type belt conveyor with disc brake size shape and connection diagram (bearing seat connection type)

图3GP-KPZ型带式输送机用盘式制动装置外形及连接尺寸图（胀套联接型）<br>Figure 3 GP-KPZ type belt conveyor with disc brakes and connection size shape figure (expansion sleeve connection type)

●用途及主要特点 Application And Main Features

·广泛用于各种鼓式制动器和盘式制动器的驱动装置，还可用于各种工业阀门、闸门，定向摆动和转动（<90°）装置及夹紧装置的驱动控制。

·按原西德EMG公司技术制造。符合DIN15430及JB/T10603-2006。

·铝合金外壳、全密封单推杆结构、外形美观、重量轻、性能安全可靠。

·电机为非油浸式结构，F级绝缘，耐热性好，寿命长。

·电机接线盒密封性好，采用电缆填料函进线，防护等级高。

·电机轴和推杆均经过表面特殊处理，使密封件寿命大大延长。

·传动部分均为双密封结构，密封效果好且性能可靠。

·油缸壳体一侧设有平衡气室，可在0\~180°范围内安装使用；连杆可以360°旋转。

·可通过增设推动器附加装置实现以下附加功能：

GQ系列-驱动装置（GB或JB部分）

·上升限位开关：可指示推动器推杆是否升到规定位置。(制动器是否打开)

·下降限位开关：可指示推动器推杆是否回到规定位置。(制动器是否闭合)

·上升阀或下降阀：可使上升或下降时间无级延长，可调整的最大值为额定值的10\~20倍。带阀的推动器，阀全开时，其上升、下降时间将会有所延长，短行程延长约1\~2秒，长行程延长约2\~4秒。

·制动弹簧：使短行程推动器产生拉力，主要是替代制动架上的制动弹簧产生制动力。主要技术参数表中的“制动弹簧力”为推动器上升行程1/3（下降行程2/3）时的弹簧力。

·复位弹簧：工作原理同制动弹簧，但弹簧力较小。主要作用是使推动器活塞及其外部连接件复位。复位弹簧力也可由用户确定，但不得超过制动弹簧力。

·缓冲弹簧：它代替连杆装在短行程推动器的活塞杆上，不改变推动器的行程。主要调节制动过程，缓冲制动的非周期瞬变过程，使制动平稳。(注意：安装缓冲弹簧的推动器不能装限位开关，且须与制动弹簧配套使用。)

·加热器：环境温度低于-20℃时，可根据用户需要加装加热器。加热器电压：AC110V或AC220V;加热器功率见下表。温度的控制调节方法由用户自选。

· Widely used to drive a variety of drum brake and disc brake, also can be used in various industrial valves, gate, directional swing and rotation (< 90 °) drive control device and clamping device.

· Manufactured according to the original German EMG company. With DIN15430 and JB/T10603-2006.

· Aluminum alloy case, sealed single push rod structure, beautiful appearance, light weight, safe and reliable performance.

· Motor for the non oil immersed type structure, class F insulation, good heat resistance, long life.

\- Motor junction box has good sealing property, the cable gland into the line, high protection level.

\- Motor shaft and a push rod through special surface treatment, The sealing life is greatly extended.

· Transmission part is the double sealing structure, good sealing effect and reliable performance.

· Cylinder shell side is provided with a balancing chamber, can be in 0 \~ 180° installation; the connecting rod can rotate 360 deg.

· Can through set up to achieve the following additional features drive additional device:

• Rise limit switch: push rod can indicate whether the specified position. (brake is open)

· Down limit switch: push rod can indicate whether back to the specified position. (brake is closed)

· Rise or drop valve: valve can rise or fall time continuously prolonging. 20 times the maximum value can be adjusted to 10 of the rated value to. Tropical valve drive, valve fully open, its rise, decline time will be extended, short stroke extended about 1 \~ 2 seconds, long range extending from about 2 to 4 seconds.

· The brake spring: the short stroke drive force, is mainly to replace the brake spring braking force produced on the shelf. The main technical parameters in the table "brake spring force\* to promote the rise of 1/3 (travel down stroke 2/3) spring force.

· The reset spring: works with brake spring, but spring force is small. The main function of which is to push the piston and the external connection reset. A reset spring force can also be determined by the user, but shall not exceed the brake spring force.

· The buffer spring: piston rod instead of connecting rod is arranged in the short stroke drive, do not change the drive travel. The main regulating braking process, non periodic transient buffer braking process, the brake stability. (Note: the installation of the buffer springs drive can not hold the limit switch, and shall be used for matching with the brake spring.)

· Heater: the environment temperature is lower than -20 C, based on user needs to install a heater. The heater voltage: AC110V or AC220V; heater power is shown in the table below. Temperature control method by the user.

加热器参数值 Heater parameters

●使用条件Use conditions

·环境温度：-20℃\~50℃使用DB-25液压油，低于-20℃时用YH-10航空液压油，可不装加热器；用DB-25液压油，必须装加热器。

·空气相对湿度不大于90%。

·使用地点海拔高度符合GB755-2008。

·工作环境中不得有易燃、易爆及腐蚀性气体。否则应采用防爆型或防腐型产品。

·电动机绝缘等级：F级;防护等级IP65。

·电缆：导线截面最大可达4×25mm²。

·电源：三相交流50HZ、380V。(本公司可提供其它不同频率、不同电压的产品)

·工作制：S1;S3-60%。

· Environment temperature: - 20 C to 50 C with the DB - 25 hydraulic oil, below - 20 C in YH - 10 aviation hydraulic oil, don't install the heater; You can use the db-25 hydraulic oil ,need to install heater.

· Use site altitude in accordance with GB755-2008.

· Work environment has no flammable, explosive and corrosive gases. You should use explosion-proof or anti-corrosion products.

· Grade: F grade; insulating

· motor protection class Ip65.

· Cable: wire section up to 4 × 25mm 2.

· 50HZ, 380V three-phase AC power supply. (the company can provide different frequency, different voltage products) · work: S1:S3-60%.

●型号意义Model significance

制动器附加装置代号Brake auxiliary device code

●安装方式Installation

·垂直安装：活塞杆、连杆朝上。

·水平及中间任意位置安装：接线盒朝上。(如下图)

·所有推动器的推杆、连杆都可以任意角度旋转。Ed50\~Ed301的安装底座可作90°旋转。也可提供安装底座作90°旋转的Ed23和Ed30，但推动器安装高度尺寸A增加8mm。

·无论何种安装方式，活塞杆均不能承受径向力，以免影响使用效果和寿命。

• vertical installation: piston rod, connecting rod upward.

• level and intermediate installed at any position: junction box at. (the following chart)

· all push rod, push rod can be arbitrary rotation angle. The mounting base of Ed50\~Ed301 can make 90 DEG rotation. Also can provide the base for 90 ° rotation of Ed23 and Ed30, but the driver installation height size A increased 8mm.

• regardless of the type of installation, the piston rod can not bear radial force, so as not to affect the use effect and the life.

●主要外形尺寸The dimensions

Ed80/6C

Ed23-Ed80

●C-弹簧曲线 C-spring curve

注：“---”压缩C-弹簧所需的力；“—”C-弹簧所产生的力（制动力）;曲线是在20℃环境温度时测定的

Note:"---" compression force required for C - spring; "-" C - spring force generated by the power (system); Curve is in 20 ℃ environment temperature measurement

●行程-时间曲线 Stroke - time curve

Ed23/5、Ed30/5

用途及主要特点 Application And Main Features

电力液压推动器是一种集电机、离心泵、油缸为一体，结构紧凑的驱动控制装置，广泛用作各种鼓式制动器和盘式制动器的驱动装置。

Electric hydraulic driver is a collection of motor, centrifugal pump, oil cylinder, compact drive control device, is widely used for various drum brake and disc brake drive.

●使用条件Use conditions

·环境温度：-20\~45℃。

·空气相对湿度不大于90%。

·使用地点的海拔高度符合GB755-2008标准。

·周围工作环境中没有易燃、易爆及足以腐蚀金属和破坏绝缘的气体和尘埃。

· Environment temperature: -20℃ -45 ℃.

· The air relative humidity of not more than90%.

· Use location altitude in accordance with GB755-2008 standard.

· The surrounding work environment is not flammable, explosive and sufficient to corrosion and damage to the insulation of gas and dust.

型号意义Model significance

●主要技术参数及外形尺寸

外形尺寸图Outline dimension drawing

●用途及主要特点Application And Main Features

·BEd隔爆型电力液压推动器主要用途是作为电力液压鼓式制动器的驱动装置，也可通过杠杆机械完成往复、圆周、摆动等形式的快速运动，适用于起重、运输、冶金、矿山、港口、建筑等行业。

·其隔爆型性能符合GB3836.2-2010《爆炸性环境第2部分；由隔爆外壳“d”保护的设备》的规定，防爆标志为“ExdIMD”、“ExdIICT4Gb”，分别用于煤矿井下及ⅡA、ⅡB、ⅡC(I类、A级Ⅱ类、B级Ⅱ类、C级Ⅱ类)温度组别为T1-T4可燃气体或蒸汽与空气形成的爆炸性混合物场所。

Bed isolation type electric hydraulic actuators are mainly used as actuators for hydraulic drum brakes, as well as through lever machin es,The rapid motion of the form of reciprocating, circumferential and swing is applied to the industries of hoisting, transport, metallurgy. mining. port and construction.

GQ系列BEd系列

. Its explosion-proof performance complies with gb3836.2-2010 \*explosive environment 2 parts; equipment for protection of" d "from the explosive enclosure, explosion-proof marks as "Exd IMD", "Exd II CT4Gb\*, respectively, used in the coal mine and the A and B I I. Il C (class I and class A I Class, the class B I, grade C I) temperature classes T1 - T4 combustible gas or steam in mixture with air to form explosive place.

使用条件 Use conditions

·海拔高度不超过1000m;

·环境温度-20℃\~+40℃；

·安装地点最湿月的月平均最大相对湿度不超过90%同时该月的平均最低温度不低于25℃，允许由于温度变化发生在产品表面的凝露；

·周围环境的污染等级允许3级；

·电源为三相交流：127V/220V、380V/660V、660V/1140V、50Hz(60Hz)。

· The altitude does not exceed 1000m;

· Ambient temperature -20 C-+40 C;

· Installation site of the wet monthly average maximum relative humidity of not more than 90% and the monthly mean minimum temperature is below 25 C, allowed due to temperature changes occurring in the product surface condensation;

· Pollution of the surrounding environment allowing level 3;

· Power of three-phase AC: 127V/220V,380V/660V,660V/1140V, 50Hz(60Hz).

●外形尺寸图Main dimensions

●外形尺寸表 Dimension table

注：具体型号、结构及外形尺寸保留更改的权利。 Note: The specific reserves the right to change the type, structure and dimension

●用途及主要特点 Application And Main Features

·电力液压推动器是一种集电机、离心泵、油缸为一体，结构紧凑的驱动控制装置，广泛用作各种鼓式制动器和盘式制动器的驱动装置。

·其隔爆型性能符合GB3836.1-2010《爆炸性环境第1部分：设备通用要求》、GB3836.2-2010《爆炸性环境第2部分：由隔爆外壳“d”保护的设备》的规定，防爆标志为“ExdI”。

• Electric hydraulic driver is a collection of motor, centrifugal pump, oil cylinder, compact drive control device, is widely used for various drum brake and disc brake drive.

• The flameproof performance meet GB3836.1-2010 \*explosive environment, part 1: general requirements for equipment and GB3836.2-2010" explosive environment part 2: the flame-proof enclosures "d\* protect the equipment of the provisions of the explosion-proof marks for \*Exd I\*.

GQ系列BYT1系列

●使用条件Use conditions

·环境温度：-20℃\~40℃。

·安装地点最湿月的月平均最大相对湿度不超过90%，同时该月的平均最低温度不低于25℃，允许由于温度变化发生在产品表面的凝霜。

·使用地点海拔高度不超过1000m。

·周围环境的污染等级允许为3级。

·电动机绝缘等级：E级;防护等级IP54。

·电源：三相交流380/660V、660/1140V。50HZ(60HZ)。

• Environment temperature: -20 ℃ \~ 40 ℃.

• The location of most of the wet monthly average maximum relative humidity of not more than 90%, while the mean, The lowest temperature is below 25 C allowed due to temperature changes occurring in the product surface frost.

• Use at an altitude of more than 1000m

• Pollution grade environment allows for the level 3.

• Grade: E grade; insulating motor protection class IP54.

• Power supply: three-phase AC 380/660V, 660/1140V. 50 HZ (60 HZ).

●型号意义Model significance

主要技术参数及外形尺寸 The main technical parameters and dimensions

不具有负荷弹簧的推动器Having no load spring drive

●用途及主要特点 Application And Main Features

·ZEd系列交直流两用电力液压推动器（以下简称推动器）是我公司在Ed推动器的基础上研制开发的产品，采用先进的无刷电机，辅以数字控制电路，适用于DC220V、AC220V的供电系统。

·具有起动平稳，噪音低，抗干扰和节能环保等特点。

·广泛用于以前使用变频器的场合，以提高系统的性能（调速范围、精度），降低成本。

·该产品由控制器和Ed电力液压推动器两部分组成(注意：在控制器带电或两个LED灯发光期间，禁止打开控制器或接触控制器内部，否则有触电的危险！)。

· Zed series AC / DC electric hydraulic driving device (hereinafter referred to as the pusher ) is my company in the Ed drive device developed on thebasis of the product,the use of advanced brushless motor, supplemented by the digital control circuit,applies to DC220V, AC220V power supply system.

· Starting with smooth, low noise, interference resistance and energy saving and environmental protection characteristics.

· Widely used in previous use of inverter occasions, in order to improve the system performance (speed range, precision, cost reduction ).

· The product consists of a controller and Ed electric hydraulic driving device composed of two parts (Note: in the controller electrically charged or two LED light emitting period, prohibit open controller or contact controller internal, otherwise the danger of electric shock!).

使用条件Use conditions

·环境温度：-20℃\~45℃(当低于-20℃时，需装加热器或使用YH-10航空油)。

·空气相对湿度不大于90%。

·通电持续率：0-100%。

·户内使用，并且周围环境符合GB/T15957中相关规定。

· Environment temperature: -20 C\~ 45 C(when is lower than -20C, need to install or use the YH-10 air oil heater )

• Air relative humidity of not more than 90%.

· Electric continuous rate: 0- 100%.

\- Indoor use, and accords with the relevant provisions in the environment GB/T15957.

●电器原理图Electrical principle chart

注：该产品技术参数和外形尺寸均与Ed相同，本说明不再赘述。请参照Ed系列电力液压推动器。 Note: The product technical parameters and overall dimensions are the same as the Ed, this note is no longer here. Please refer to the Ed series electric hydraulic driver.

●用途及主要特点 Application And Main Features

·该产品采用创新的设计理念，把液压系统和电磁系统有效的结合，优势互补，各取所长，具有运行可靠、节能、寿命长的特点。该产品在制动器驱动装置领域具有创新性。

·主要用于皮带运输机、石油机械、架桥机等需要长时间可靠运行的制动器成套设备上。

·DEd电磁节能液压推动器上安装EB1上升感应开关时，通过控制盒电控系统能实现电磁吸合维持失效时电力液压推动器自动启动的功能。

·在控制盒损毁无法正常工作情况下，可将380V、50HZ工作电源直接接入推动器电机内，用电力液压推动器正常工作。

·其余特点参照Ed系列电力液压推动器的性能特点。

· The product innovative design concept, the combination of the hydraulic system and electromagnetic system effectively, complementary advantages, from each director, has reliable operation, energy saving, long life characteristics. The product in the field of brake drive innovative.

· Settled mainly used in belt conveyor, oil machinery, such as need long time on the reliable operation of the brake equipment.

· Ded electromagnetic energy-saving hydraulic driver installed on the EB1 rise induction switch, through the control box electric control system can realize the electromagnetic and maintain fails driver power hydraulic automatic start function.

• In the control box of damaged cannot work normally, 380 v, 50 hz power supply can be directly connected to the driver motor, hydraulic driver work by electricity.
· The rest of the characteristics of reference to the performance characteristics of electric hydraulic push Ed series.

使用条件 Use conditions

·环境温度：-20℃\~45℃

·外界空气相对湿度不大于90%。

·三相交流380V、50HZ。

·连续工作S1，断续工作S3-60%。

· Environmental temperature: -20 C\~45℃

· Outside air relative humidity is not greater than 90%.

·电源绝缘等级F级，电器防护等级IP65。

· Three-phase AC 380V, 50 HZ.

\- Work continuously S1, intermittent work S3-60%.

\- Power insulation class F, electrical protection grade IP65.

●型号意义Model significance

●产品型号 Product model

· DEd50/6 DEd80/6 DEd121/6 DEd201/6DEd301/6

·具体技术数据和外形连接尺寸与Ed系列电力液压推动器相同。

· DEd50/6 DEd80/DEd121/6 DEd201/ DEd301/6

· Detailed technical data and connection shape size is the same as the Ed series electric hydraulic driver.

电控盒外形尺寸 Electric control box dimension

·190mm×160mm×130mm 可在推动器三个方向安装。

· 190 mm × 160 mm × 130 mm can install driver in three directions.

外形示意图Main dimensions

推动器附加装置Additional device driver

注：具体型号、结构外形尺寸保留更改的权利。

Note: The specific reserves the right to change the type, structure and dimension.

●用途及主要特点Application And Main Features

·适用于连接同轴线、启动频繁、正反转变化，中速、中等转矩传动轴系和要求工作可靠性高的工作部位。

·符合GB/T5272-2002。

·结构简单，免润滑，维护方便。

·可补偿两轴相对位移，径向尺寸小。

· Be suitable for connecting coaxial, frequent starting, positive change, medium, medium torque transmission shaft and requires high reliability work site.

• In line with GB/T5272-2002.

· The advantages of simple structure, convenient maintenance and lubrication free.

·减震、缓冲性能好，承载能力大。

· Compensate the relative displacement, small radial dimension.

· Shock absorption, good buffering performance, large carrying capacity.

●使用条件 Use conditions

·工作温度：-35℃\~80℃。

· Working temperature: -35℃ - 80 ℃.

·更换弹性件需轴向移动。

· The elastic member to move axially replacing .

●型号意义Model significance

符合标准 Conform to the standard

·制动轮符合JB/ZQ4389-97。

• Brake wheel with JB/ZQ4389-97.

·键槽型式、尺寸及公差符合GB/T3852-1997。

• Keyway type, dimensions and tolerances in accordance with GB/T3852-1997.

●型号意义Model significance

●主要技术参数及外形尺寸The main technical parameters and dimensions

符合标准 Conform to the standard

·制动盘符合JB/T7019-93（B型）。

• Brake disc with JB/T7019-93 (B type).

·键槽型式、尺寸及公差符合GB/T3852-1997。

• Keyway type, dimensions and tolerances in accordance with GB/T3852-1997.

●型号意义Model significance

GQ-DKZ-220

●主要技术参数及外形尺寸

The main technical parameters and dimensions

●用途及主要特点 Application And Main Features

·GQ-DKZ型电磁鼓式制动器电源箱是我公司为ZWZA和ZWZ3系列电磁鼓式制动器配套的电源，依据用户要求订货时须特殊说明；配套该型电源箱。常规产品没有电源箱。

· GQ-DKZ type electromagnetic brake power box is my company for the ZWZA and ZWZ3 series electromagnetic brake drum supporting the power box. According to user requirements when you order it must be special instructions;Supporting the power box.Normal product without power box.

使用条件 Use conditions

·环境温度：-10℃\~40℃。

·空气相对湿度不大于90%。

·使用地点海拔高度符合GB/T14048.1-2000。

·工作环境中不得有易燃、易爆及足以腐蚀金属和破坏绝缘的气体和导电尘埃。

·电源：交流50HZ、380V。

· Environment temperature: -10 ℃ \~ 40 C.

• Air relative humidity of not more than 90%.

• Use site altitude in accordance with GB/T14048.1-2000.

· Work environment has no flammable, explosive and gas to corrosion and damage to the insulation and conductive dust.
· Power: AC 50HZ, 380V.

型号意义Model significance

注：1.根据所配制动器的型号、通电率不同，功率、重量不同。2.具体型号、结构及外形尺寸保留更改的权利。
Note: 1. According to the type of brake, TongDianLv different, different power and weight.2.The specific reserves the right to change the type, structure and dimension

用途及主要特点Application And Main Features

·GQ-TW。、GQ-TYW型脚踏泵是我公司专门为配套TYWZ系列、TYW系列液压式鼓式制动器设计的人力转换为液压动力源的机构，主要用于门座起重机和塔式起重机、回转机构等的减速制动的动力源。一台脚踏泵最多可驱动两台液压鼓式制动器。

·外形结构充分结合了门式或塔式起重机工作室的安装特点设计，且结构紧凑，安装、操作方便。

· GQ-Tw2 and GQ-TYW foot pumps are the mechanisms designed by our company to convert manpower into hydraulic power source for supporting TYWZ series and TYW series hydraulic drum brakes. They are mainly used as power sources for deceleration braking of portal cranes, tower cranes, slewing mechanisms, etc. One foot pump can drive up to two hydraulic drum brakes.

· Shape structure fully combined the gantry or studio installation characteristics of the design of tower crane, and compact structure, installation, convenient operation.

GQ-TW2200-200aGQ-TW2400-200b

GQ-TYW40-100-HXa

主要技术参数及外形尺寸 The main technical parameters and dimensions

单位：mm

●用途及主要特点 Application And Main Features

·脚踏变频控制器和制动器结合组成脚踏变频制动器，适用于起重机的旋转机构、大车或小车的驱动机构等减速和停车制动。

·控制器通过改变脚踏控制器的幅度来改变输出频率，无级调整推动器电机的转速，从而改变推动器推力的大小和上升时间，实现对制动力矩的调节。将控制器应用于制动器产品上，可实现工作状态下多驱动同步控制，制动力矩与脚踏幅度成线性关系。

· Pedal frequency conversion controller and brake pedal brake consists of a combination of frequency conversion, suitable for crane rotary mechanism, cart or trolley driving mechanism reducer and a parking brake.

· By changing the amplitude controller foot controller to change the output frequency,stepless adjustment drive motor speed, thereby changing the propeller thrust size and rise time, realizes to the braking torque control. The controller is applied to the brake products, can be achieved under the working condition of synchronization control, brake torque and pedal amplitude linear relationship.

●使用条件 Use conditions

·环境温度：-10℃\~-40℃室内(无腐蚀性气体和尘埃)。·Environment temperature:-10℃\~-40Cindoor(nocorrosivegasanddust).

·电源电压：380V、50HZ。

\- Intermittent duty S3 - 60%.

·断续工作制S3—60%。 • Controller and the motor wiring distance of 30 meters.

·控制器与电机接线距离30米以内。

电气连接示意图 Electrical connection schematics

外形及安装尺寸Outline and mounting dimensions

注：具体型号，结构外形尺寸保留更改的权利。

Note: The specific reserves the right to change the type, structure and dimension.

●用途及主要特点Application And Main Features

·GQ-YZ型液压站主要作为安全液压盘式制动器的驱动动力源。

·多功能复合控制方式，在断电检修时，依靠人力实现上压过程（带手动打开装置：手动泵）。

·结构紧凑、造型美观、保压性能稳定。

·设有防尘罩，适应露天作业。

• GQ-YZ hydraulic station is mainly used as the drive power source hydraulic disc brake.

· Multifunctional composite control mode, in the power-off overhaul, rely on pressure process of human realization (with manual opening device: a manual pump).

GQ系列YZ型

· Compact structure, beautiful appearance, pressure maintaining stable performance.

• The dustproof cover, adapt to the open job.

●使用条件Use conditions

·环境温度：-10℃\~+40℃。

· Ambient temperature: - 10℃ - + 40 ℃.

·湿度：空气相对湿度不大于90%。

· Humidity: the air relative humidity is not greater than90%.

·电机工作电源：三相，AC380V、50HZ。(如需其他电压,请订货时事先说明)。

· Electrical motor power: three phases, AC380V, 50HZ. If you need any other voltage, please specify in advance.

· Applicable working system: S3, 25%.

·适用工作制：S3,25%。

· This hydraulic station only applies to safety brakes.

·此液压站仅适用于安全制动器。

●型号意义Model significance

●GQ-YZ液压站参数表 The main technical parameters

●主要外形尺寸The dimensions

单位:mm

液压站液控图 Hydraulic station hydraulic control chart