该页无缩略图
(2)Accuracy of interchangeability linear guide rails
unit:mm
| Model | EB-15,20 | ||
| Accuracyclass | Commonlevel(C) | High level(H) | Precision level(P) |
| TolerancesizeerrorforheightH | ± 0.1 | ±0.03 | ±0.015 |
| Tolerance sizeerror for width N | ± 0.1 | ±0.03 | ± 0.015 |
| Mutual error of the pairwise height H | 0.02 | 0.01 | 0.003 |
| Mutual error of thepairwisewidth N | 0.02 | 0.01 | 0.005 |
| Slide C faces the walkingparallelism of the guiderailplaneA | WalkparallelismSee theform2-2-7 | ||
| ThelideDfacestheguideB | WalkparallelismSeetheform2-2-7 | ||
unit: mm
| Model | EB-25,30,35 | ||
| Accuracyclass | Common level(C) | High level(H) | Precision level(P) |
| Tolerance size error forheight H | ± 0.1 | ± 0.04 | ± 0.02 |
| Tolerancesizeerrorforwidth N | ± 0.1 | ±0.04 | ±0.02 |
| Mutual error of the pairwise height H | 0.02 | 0.015 | 0.007 |
| MutualerrorofthepairwisewidthN | 0.03 | 0.015 | 0.007 |
| Slide C faces the walking parallelism of the guide rail plane A | Walkparallelism See the form2-2-7 | ||
| The lide D faces the guide B | Walkparallelism See the form2-2-7 | ||
(3)Walking parallelism accuracy
| Sliderlength(mm) | Accuracylevel(um)C | H | P | SP | UP | ||
| 100 | 12 | 7 | 2 | 2 | |||
| 100 | 200 | 14 | 6 | 4 | 2 | 2 | |
| 200 | 300 | 15 | 10 | 5 | 2 | ||
| 300 | 500 | 17 | 12 | 6 | 3 | 2 | |
| 500 | 700 | 20 | 13 | 7 | 4 | 2 | |
| 700 | 900 | 22 | 15 | 8 | 5 | 3 | |
| 900 | 1,100 | 24 | 16 | 6 | 6 | ||
| 1,100 | 1,500 | 26 | 18 | 11 | 7 | 4 | |
| 1,500 | 1,900 | 28 | 20 | 13 | 8 | 4 | |
| 1,900 | 2,500 | 31 | 22 | 15 | 10 | 5 | |
| 2,500 | 3,100 | 33 | 25 | 18 | 11 | 6 | |
| 3,100 | 3,600 | 36 | 27 | 20 | 14 | 7 | |
| 3,600 | 4,000 | 37 | 28 | 21 | 15 | 7 | |
2-2-6 Prepressure
(1) Prepressure definition
The prepressure is to give the steel bead load force in advance, that is,increase thediameterbetweenthesteelbeadand thebead,whichcan improvetherigidityofthelinearrailandeliminatetheclearance.Inthe abovediagram,improvingtheprepressurecanincrease therigidityof the linearrail.However,it is recommended to avoid theheavy prepressure to reduceitsservicelife.
(2)Prepress level
The EB series linear guide rail provides three standard prepressure, and the appropriate prepressure can be selected accordingtotheuse.
| Preloadrating | Marking | Prepressure | Conditionsofuse | |
| Noprepressure | ZO | 0-0.02C | fixedloaddirectionandsmallimpact,lowprecisionrequirements | |
| Lightprepressure | ZA | 0.03C-0.05C | lightloadandhighprecisionrequired | |
| Mediumprepressure | ZB | 0.06C-0.08C | highrigidityrequirements,andvibration,impactoftheoperatingenvironment | |
| Level | Interchangeablewirerail(singlepiece) | Non-interchangeablewirerail(assemblypiece) | ||
| Prepressinglevel | ZO,ZA | ZO,ZA,ZB | ||
2-2-7 Lubrication system
(1)Lubricant grease
⊚ Nozzle position
According to the customer,install the front orback end of the sliderfor manual oil drilling,EB series specially sets the side oil hole on the side of the end cover(generally the straight oil nozzle).Provide the side oil drilling,but it can alsobe placed on the side base side if there is special need.If the customer has the above side oil demand, please contact us. EB series also reserves an oil hole at the top of the end cover. If the customer wants to supply oil from the top of the end cover,it must use ametalneedleof 0.8mm diameter in order to preheat the oil holein the designatedposition,and theninstall theseal ring in the concave to avoid using the drill hole through the oil hole, andtheriskofpolluting theoilchannel.If thelinearguiderail automatically supplies lubricating grease,the oil pipe joint can be installed according to the connecting pipe type.
⊚ The grease volume of single slider filled with lubrication
⊚ Lubrication rate
| form | mediumload（cm3) | heavyload（cm3) |
| EB15 | 0.8 | 1.4 |
| EB20 | 1.5 | 2.4 |
| EB25 | 2.8 | 4.6 |
| EB30 | 3.7 | 6.3 |
| EB35 | 5.6 | 6.6 |
Check the grease for every 100k m run,or every3 to 6 months.
(2)Lubrication oil
It is recommended to use the straight oil lubrication rail of about 32 ~ 150 cSt. The customer can explain to us that oil lubrication is needed, and the shipped straight rail will not be sealed in lubricating grease.
⊚ Form of oil tube joint
Table 2-2-11 oil supply rate
| form | oilsupplyrate(cm3/hr) |
| EB15 | 0.1 |
| EB20 | 0.133 |
| EB25 | 0.167 |
| EB30 | 0.2 |
| EB35 | 0.233 |
2-2-8 Dust-proof accessories
(1)Dust-proof equipment code
Standard If the following dust proof requirements are available, please add the code after the product model.
(2)Dust-proof equipment instructions
⊚ Oil scraper and bottom dustproof sheet
Prevent processing iron chips or dust particles from entering the slider, destroy the surface of the bead path and reduce thelifeofthelinearguiderail.
⊚ Double layer scraping sheet
Double the scraping effect, even in the heavy cutting environment, foreign matter are completely excluded from the slide.
| Sspecification | Thicknees(t1)(mm) |
| EB 15 ES | 2 |
| EB 20 ES | 2 |
| EB 25ES | 2 |
| EB30ES | 2 |
| EB35ES | 2 |
⊚ Metal scraper
ture iron chips or processing sparks, and eliminate large volume im
| Specification | Thicknees(t2)(mm) |
| EB15SC | 0.8 |
| EB20SC | 0.8 |
| EB25SC | 1 |
| EB30SC | 1 |
| 53 EB35SC | 1.5 |
⊚ Guide rail bolt cover
In order to prevent the cutting powder or foreign body from invading the slide through the bolt hole, the customer must insert the bolt cover into the bolt hole when installing the rail, and each rail is equipped with a bolt cover at the factory.
| OD | 工 |
| Guidespecification | Installthescrew | Diameter（D)（mm) | Thickness(H)(mm) |
| EBR 15R | M3 | 6.15 | 1.2 |
| EBR20R | M5 | 9.65 | 2.5 |
| EBR25R | M6 | 11.15 | 2.5 |
| EBR30R | M6 | 11.15 | 2.5 |
| EBR35R | M8 | 14.20 | 3.5 |
| EBR 15U | M4 | 7.65 | 1.1 |
| EBR30U | M8 | 14.20 | 3.5 |
(3)Total length of the slider for each dust proof coc
| Specifications | Total lengthofslider(L) | |||
| SS | ZZ | DD | KK | |
| EB15S | 40.1 (42.5) | 41.7 (46.1) | 44.1 (46.5) | 45.7 (50.1) |
| EB15C | 56.8 (59.2) | 58.4 (62.8) | 60.8(63.2) | 62.4 (66.8) |
| EB20S | 50.0 (54.0) | 51.6 (57.6) | 54.0 (58.0) | 55.6 (61.6) |
| EB20C | 69.1 (73.1) | 70.7 (76.7) | 73.1 (77.1) | 74.7 (80.7) |
| EB25S | 59.1 (63.1) | 61.1 (67.1) | 63.1 (67.1) | 65.1 (71.1) |
| EB25C | 82.6 (86.6) | 84.6 (90.6) | 86.6 (90.6] | 88.6 (94.6) |
| EB30S | 69.5 (73.5) | 71.5 (77.5) | 73.5 (77.5) | 75.5 (81.5) |
| EB30C | 98.1 (102.1) | 100.1 (106.1) | 102.1 (106.1) | 104.1 (110.1) |
| EB35S | 75.0 (79.0) | 78.0 (84.0) | 79.0 (83.0) | 82.0 (88.0) |
| EB35C | 108.0 (112.0) | 111.0 (117.0) | 112.0 (116.0) | 115.0 (121.0) |
2-2-9 Friction force
EBseriesisa two-pointcontact linearguide,whoseautomaticcentering characteristicscanabsorbsomeerrorsofthemounting surface without affecting the smooth performance of linear movement;the allowable error value in thefollowing table:
| Specifications | Scrapperresistance N(kgf) |
| EB 15 | 0.98 (0.1) |
| EB20 | 0.98 (0.1) |
| EB25 | 0.98 (0.1) |
| EB30 | 1.47 (0.15) |
| EB35 | 1.96 (0.2) |
2-2-10 Install plane error
linearguide，whoseautomatic centeringcharacteristics canabsorbsomeerrorsofthemountingsurfacewithout affecting the smooth performance of linear movement; the allowableerrorvalueinthefollowingtable:
unit: μm
| specifications | Pre-pressuregrade | ||
| ZoPre-pressure | ZAPre-pressure | ZBPre-pressure | |
| EB 15 | 25 | 18 | |
| EB 20 | 25 | 20 | 18 |
| EB 25 | 30 | 22 | 20 |
| EB30 | 40 | 30 | 27 |
| EB35 | 50 | 35 | 30 |
| specifications | Pre-pressuregrade | ||
| ZOPre-pressure | ZAPre-pressure | ZBPre-pressure | |
| EB 15 | 130 | 85 | |
| EB 20 | 130 | 85 | 50 |
| EB25 | 130 | 85 | 70 |
| EB30 | 170 | 110 | 90 |
| EB35 | 210 | 150 | 120 |
2-2-11 Installation precautions
(1)Shoulder height and chamfer of the mounting surface
When installing the linear guide rail, we must pay attention to whethertheconditionoftheshoulderoftheinstallationsurfaceis appropriate.If the chamfering is toolarge, the protruding place is easy to cause the poor accuracy of the linear guide rail, and if the height is too high, it will interfere with the slider. Therefore, if the surfaceandshouldercanbeinstalledaccordingtothe recommendedrequirements,the poorinstallation accuracy can be eliminated.
| Specifications | Maximumchamferof theguiderailr,（mm) | Maximumchamferof thesliderr（mm) | Shoulderheightof theguiderailE,（mm) | Shoulderheightof thesliderE（mm) | Sliderrunning netheightH,（mm) |
| EB 15 | 0.5 | 0.5 | 2.7 | 5.0 | 4.5 |
| EB 20 | 0.5 | 0.5 | 5.0 | 7.0 | 6.0 |
| EB 25 | 1.0 | 1.0 | 5.0 | 7.5 | 7.0 |
| EB30 | 1.0 | 1.0 | 7.0 | 7.0 | 10.0 |
| EB35 | 1.0 | 1.0 | 7.5 | 9.5 | 11.0 |
(2)Torsion force value of the guide rail assembly screw
Whether the installation of the guide rail is close to the flat datum affects the accuracy of the straight guide rail, so in order to achieve the purpose of locking each screw, it is recommended to use the following torsion value lock to assemble the screw.
| Specifications | Screwspecifications | Torsional forcevalueN-cm(kgf-cm) | ||
| lronmaterial | Castingmaterial | Aluminumalloymaterial | ||
| EB15 | M3x0.5Px16L | 186 (19) | 127 (13) | 98 (10) |
| EB20 | M5x0.8Px16L | 883 (90) | 588 (60) | 441 (45) |
| EB25 | M6x1Px20L | 1373 (140) | 921 (94) | 686 (70) |
| EB30 | M6x1Px25L | 1373 (140) | 921 (94) | 686 (70) |
| EB35 | M8x1.25Px25L | 3041 (310) | 2010 (206) | 1470 (150) |
2-2-12 Standard length and maximum length of a single guide rail
JSM has a guide rail standard length inventory for customer demand. If the customer orders the non-standard length rail, the end surface distance E should not be greater than 1/ 2P, so as to prevent the instability of the rear end of the rail assembly due to thelarge size of E,and reduce the precision of thelinear rail.
L=(n-1)x P+2x E
L :Guide length (mm) (mm P :Distance between bolt holes (mm) (m) n :Number of bolt holes E :Distance from bolt hole to end face (mm)
unit:mm
| item | EBR15 | EBR20 | EBR25 | EBR30 | EBR35 |
| Standard length L(n) | 160 (3) | 220 (4) | 220 (4) | 220 (4) | 220 (4) |
| 220 (4) | 280 (5) | 280 (5) | 440 (6) | 440 (6) | |
| 280 (5) | 340 (6) | 340 (6) | 600 (8) | 600 (8) | |
| 340 (6) | 460 (8) | 460 (8) | 760 (10) | 760 (10) | |
| 460 (8) | 640 (11) | 640 (11) | 1,000 (13) | 1,000 (13) | |
| 640 (11) | 820 (14) | 820 (14) | 1,640 (21) | 1,640 (21) | |
| 820 (14) | 1,000 (17) | 1,000 (17) | 2,040 (26) | 2,040 (26) | |
| 1,240 (21) | 1,240 (21) | 2,520 (32) | 2,520 (32) | ||
| 1,600 (27) | 1,600 (27) | 3,000 (38) | 3,000 (38) | ||
| Spacing (P) | 60 | 60 | 60 | 80 | 80 |
| Standard end distance (Es) | 20 | 20 | 20 | 20 | 20 |
| Maximum length of standard end distance | 4,000 (67) | 4,000 (67) | 4,000 (67) | 3,960 (50) | 3,960 (50) |
| Maximum length | 4,000 | 4,000 | 6,000 | 6,000 | 6,000 |
EB series
Low-assembly type rolling bead linear
2-2-13 HB series linear guide rail size form
| Model | Component size (ww) | Guidetracksize (mm) | Fixed bolt size of the guide rail | Basic dynamic rated loadrated load | Basic static | Allowthe staticmoment | weight | |||||||||||||||||||
| H | H | NWB | B C | Slidersize (mm) | K, K2 | G | Mxl | T | H2 | HWHR | D h | d | P | (ww) | C(kN) | C。(kN) | MR | Mp kN-mkN-mkN-m | M kg | slider | Guide rail kg/m | |||||
| EBH15SA | 24 | 4.59.53426 | 4 | 23.1 40.1 | 14.8 10.15 | 3.5 | 5.7 M4x6 | 6 | 5.5 | 6 | 15 | 12.56 | 5.34.5 | M3x16 | 5.08 | 8.93 15.38 | 0.08 0.12 | 0.04 0.10 | 0.04 0.10 | 0.09 0.15 | 1.25 | |||||
| EBH15CA EBH20SA | 28 6 | 11 42 | 26 | 39.8 29 | 56.8 50 18.75 | 4.15 | 12 | M5x7 | 7.5 6 | 6 | 60 | M5x16 | 7.44 6.87 | 12.10 | 0.12 | 0.06 | 0.06 | 0.15 | 2.08 | |||||||
| EBH20CA | 32 | 5 32 | 48.1 35.5 | 69.1 12.3 59.1 | 2015.59.58.5 | 6 | 9.79 10.83 | 20.07 18.53 | 0.21 0.22 | 0.15 0.11 | 0.15 0.11 | 0.24 0.25 | ||||||||||||||
| EBH25SA EBH25CA | 33 7 | 12.54835 | 6.5 | 35 | 59 | 21.9 82.6 16.15 | 4.55 | 12 | M6x9 | 8 8 | 8 | 23 | 18 11 | 9 | 7 | 60 | M6x20 | 15.46 | 30.78 | 0.36 | 0.30 | 0.30 | 0.41 | 2.67 | ||
| EBH30SA | 42 10 | 16 60 | 40 10 | 40 | 41.5 70.1 | 69.5 26.75 98.1 21.05 | 6 | 12 M8x12 | 9 | 8 | 6 | 28 | 23 11 | 12 | 6 80 | 20 | M8x25 | 15.60 22.52 | 26.70 45.09 | 0.38 0.65 | 0.20 0.52 | 0.20 0.52 | 0.45 0.76 | 4.35 | ||
| EBH30CA EBH35SA | 45 | 75 28.5 | M8x12 | 21.53 | 35.51 | 0.53 | 0.29 | 0.29 | 0.74 | |||||||||||||||||
| EBH35CA | 48 11 | 18 | 70 | 50 10 | 50 | 78 | 108 20 | 7 | 12 | 10 | 8.58.53427.514 | 6 | 80 | 20 | M8x25 | 31.68 | 61.60 | 0.93 | 0.66 | 0.66 | 1.10 | 6.14 | ||||
EB series
Low-assembly type rolling bead linear
2-2-13 HB series linear guide rail size form
| Model | Component size (mm) | Guidetracksize (mm) | Fixed bolt size of the | Basic dynamic guide railrated load rated lood | Basic static | Allowthe staticmoment | weight | ||||||||||||||||||||
| H | H NWB | B | C | Slidersize | (mm) K, | K2 G | M | TTHHWHR | D h | d | (mm) | C(kN) | Co(kN) | MR kN-mkN-m | Mp | M kN-m | slider kg | Guide rail kg/m | |||||||||
| EBW15SA | 24 | 4.518.552 | 41 5.5 | 26 | 23.1 | 40.1 | 14.8 3.5 | 5.7 | M5 | 5 7 | 5.5 | 6 | 1512.56 | 5.34.560 | 20 | M3x16 | 5.08 7.44 | 8.93 15.38 | 0.08 0.12 | 0.04 0.10 | 0.10 | 0.04 | 0.12 | 1.25 | |||
| EBW15CA EBW20SA | 28 6 | 19.559 | 49 | 5 | 39.8 29 | 56.8 50 | 10.15 18.75 | 4.15 | 12 M6 | 7 | 6 6 | 6 | 2015.59.58.5 | 60 | 20 | M5x16 | 6.87 | 12.10 | 0.12 | 0.06 | 0.06 | 0.21 0.19 | 2.08 | ||||
| EBW20CA | 32 | 48.1 35.5 | 69.1 59.1 | 12.3 21.9 | 9.79 10.83 | 20.07 18.53 | 0.21 0.22 | 0.15 0.11 | 0.15 0.11 | 0.32 0.35 | |||||||||||||||||
| EBW25SA EBW25CA | 33 7 | 25 7360 | 6.5 35 | 59 | 82.6 | 16.15 | 4.55 12 | M8 | 7.510 | 8 | 8 | 23 | 18 | 11 | 6 7 | 60 | 20 | M6x20 | 15.46 | 30.78 | 0.36 | 0.30 | 0.30 | 0.59 | 2.67 | ||
| EBW30SA | 42 10 | 31 90 | 72 | 9 | 41.5 70.1 | 69.5 98.1 | 26.75 21.05 | 6 12 | M10 | 7 | 10 8 | 9 | 28 | 23 | 11 12 | 9 | 80 | 20 | 15.60 M8x25 22.52 | 26.70 45.09 | 0.38 0.65 | 0.20 0.52 | 0.20 0.52 | 0.62 1.04 | 4.35 | ||
| EBW30CA | 82 | 40 | 45 | 75 | 28.5 | 21.53 | 35.51 | 0.53 | 0.29 | 0.29 | 0.84 | ||||||||||||||||
| EBW35SA EBW35CA | 48 11 | 33 | 100 | 9 | 50 | 78 | 108 | 20 | 7 12 | M10 | 10138.58.53427.514 | 12 | 9 | 80 | M8x25 | 31.68 | 61.60 | 0.93 | 0.66 | 0.66 | 1.45 | 6.14 | |||||
EB series
Low-assembly type rolling bead linear
2-2-13 HB series linear guide rail size form
| Model H | Component size (mm) | Slidersize (mm) | Guidetracksize (mm) | Fixed bolt size of the guiderail | Basic Basic dynamic static rated loadrated load | Allowthe staticmoment | weight | ||||||||||||||||||||
| H,NWB | B | C | K, | K | G M | T | TH2HWHR | D h | d | E (mm) | C(kN) | C。(kN) | MR kN-m | Mp kN-mkN-m | M | slider kg | Guide rail kg/m | ||||||||||
| EBW15SB | 24 | 4.518.552 | 41 | = 5.5 | 23.1 | 40.1 | 14.8 3.5 | 5.74.5 | 7 | 5.5 | 6 | 1512.56 | 5.34.5 | 60 20 | M3x16 | 5.08 | 8.93 | 0.08 | 0.04 | 0.04 | 0.12 | 1.25 | |||||
| EBW15CB | 26 | 39.8 29 | 56.8 50 | 10.15 18.75 | 125.5 | 7 | 6 | 7.44 6.87 | 15.38 12.10 | 0.12 0.10 0.12 0.06 | 0.10 0.06 | 0.21 0.19 | |||||||||||||||
| EBW20SB EBW20CB | 28 | 6 | 19.559 | 49 | 5 | 32 48.1 | 69.1 | 12.3 | 4.15 | 6 | 6 | 2015.59.58.5 | 60 | M5x16 | 9.79 | 20.07 | 0.21 | 0.15 0.11 | 0.15 | 0.32 | 2.08 | ||||||
| EBW25SB | 33 | 7 | 25 | 7360 | 35.5 35 59 | 59.1 82.6 | 21.9 16.15 | 4.55 12 | Φ7 | 7.510 | 8 | 8 | 23 | 18 11 | 9 | 7 | 60 20 | M6x20 | 10.83 15.46 | 18.53 30.78 | 0.22 0.36 | 0.30 | 0.11 0.30 | 0.35 0.59 | 2.67 | ||
| EBW25CB EBW30SB | 42 10 | 31 90 | 72 | 9 | 41.5 | 69.5 | 26.75 21.05 | 6 12 | 6Φ | 7 | 10 8 | 6 | 28 | 23 11 | 12 | 6 | 80 20 | M8x25 | 15.60 22.52 | 26.70 45.09 | 0.65 | 0.38 | 0.20 0.52 0.52 | 0.20 | 0.62 | 4.35 | |
| EBW30CB | 82 | 40 | 70.1 45 | 98.1 75 | 28.5 | 12 | 21.53 | 35.51 | 0.53 0.29 | 0.29 | 1.04 0.84 | ||||||||||||||||
| EBW35SB EBW35CB | 48 11 | 33 | 100 | 9 | 50 | 78 | 108 | 20 | 7 | 6Φ | 10138.58.53427.514 | 12 | 6 | 80 | M8x25 | 31.68 | 61.60 | 0.93 0.66 | 0.66 | 1.45 | 6.14 | ||||||
EB series
Low-assembly type rolling bead linear
2-2-13 HB series linear guide rail size form
(4) Upper locking type (increased bolt aperture) rail size form
| Specification | Dimensionsof guiderail fasteningbolts (mm) | Guidetracksize（mm) | Weight | ||||||
| WR | HR | D | h | d | P | E | (kg/m) | ||
| EBR15U | M4x16 | 15 | 12.5 | 7.5 | 5.3 | 4.5 | 60 | 20 | 1.23 |
| EBR30U | M8x25 | 28 | 23 | 14 | 12 | 6 | 80 | 20 | 4.23 |
(5) down locking type guide rail dimension table
| Specification | Guiderailsize（mm) | Weight | |||||
| WR | HR | S | h | P | E | (kg/m) | |
| EBR15T | 15 | 12.5 | M5x0.8P | 7 | 60 | 20 | 1.26 |
| EBR20T | 20 | 15.5 | M6x1P | 6 | 60 | 20 | 2.15 |
| EBR25T | 23 | 18 | M6x1P | 10 | 60 | 20 | 2.79 |
| EBR30T | 28 | 23 | M8x1.25P | 14 | 80 | 20 | 4.42 |
| EBR35T | 34 | 27.5 | M8x1.25P | 17 | 80 | 20 | 6.34 |
2-3 MB series-micro small ball straight guide rail
2-3-1 Features of MBN series small linear rails
1. Small size, lightweight, especially suitable for miniaturization equipment.
2.Adopt the gothic four-point contact design, which can withstand the load in all directions, with strong rigidity and high precisioncharacteristics.
3.Steel bead holder design,with interchangeability with accuracy allowed.
2-3-2 The MBN series ontology structure
⊚ Rolling cycle system: slide block, guide rail, end cover, steel bead, and holder
⊚ Lubrication system: MBN15 has oil nozzle to the side, while MBN 7,9,12 reserve oil holes to the side to drive oil or grease into the slider forlubrication.
⊚ Dust proof system: oil scraper, dust proof (9,12,15 optional), bolt cover (12,15).
2-3-3 Characteristics of MBW small wide-linear guide rail
1. The design of the widened guide rail greatly improves the torque load capacity, which can be used in a single axis.
2. Gothic four-point contact design can withstand loads in various directions and has high rigidity.
3. The slider is equipped with a small steel wire, and the steel ball of the slide block will not fall off.
2-3-4 The MBW series ontology structure
⊚ Rolling cycle system: slide block, guide rail, end cover, steel bead, and holder.
⊚ Lubrication system: MBW 15 end cover with a nozzle to fill the customer, while MBW 7,9,12 reserve oil holes on the end cover side todrive oil or grease into the slider for lubrication.
⊚ Dust proof system: oil scraper, dust proof (9,12,15 optional), bolt cover (12,15).
2-3-5 Features of MBN-O series small linear guide rail
1. Small and lightweight,the main part of the slider is made of resin material, reducing the weight by about 20%
2. Adopt the Gothic type four-point contact design, which can withstand the load in all directions, with strong rigidity and high
precisioncharacteristics.
3.Steelbead holder design,with interchangeabilitywith accuracy allowed.
4.Modularrefluxsystemdesign.
2-3-6 The MBN-O series ontology structure
⊚ Rolling cycle system: slide block, guide rail, end cover, steel bead, and holder
⊚ Lubrication system: MBN15-O end cover side to provide the customer for oil injection, while MBN 5-O, MBN 7-O, MBN 9-O, MBN12-O reserve oil holes on the end cover side to drive oil or oil into the slider for lubrication.
⊚ Dust proof system: oil scraper, dust proof (9,12,15 optional), bolt cover (12,15).
2-3-7 Characteristics of the MBW-O small and wide-width linear guide rail
1. The design of the widened guide rail greatly improves the torque load capacity, which can be used in a single axis.
2. Gothic four-point contact design can withstand loads in various directions and has high rigidity.
3. The slider is equipped with a small steel wire, and the steel beads of the slide block will not fall off.
4.Modularreflux system design,using resin material,weight reduced by about 20%
2-3-8 The MBW-O series ontology structure
⊚ Rolling cycle system: slide block, guide rail, end cover, steel bead, and holder
⊚ Lubrication system: MBW 15-O has a nozzle on the side to supply oil, while MBW 5-O, MBW 7-O, MBW 9-O, MBW 12-O reserve oil holes on the end cover to drive the oil or oil into the slider for lubrication.
⊚ Dust control system: oil scraper, dust filter (9,12,15 specification optional), bolt cover (12,15 specification)
2-3-9 Application range
The MB N/M BW series of applications include: semiconductor manufacturing equipment, printed circuit board IC assembly equipment, medical equipment, robotic arm, precision measuring instruments, office automation equipment, and other small linearslidingdevices.
2-3-10 Product specifications and models
interchangeability and interchangeability type two straight rail, the same size, the main difference lies in the interchangeability type of slider, rail can be single swap use, more convenient, but its combined precision cannot reach the interchangeability precision requirements, but because of the JSM in manufacturing good size control and strict quality requirements,interchangeability type of combination precision has reached a certain level, does not need to pair install straight rail customers, is a good choice. The product model mainly indicates the series, size, type, accuracy grade, prepressure and other specifications, as well as the product confirmation of both parties when ordering.
(1)Non-interchangeability linear guide rail product model
Note: 1. Not the number of uniaxial guide if only one guide is used,Two branches are labeled ll, three branches are labeled Ill, and so on.
2.MBN,MBW 9,12,15,dust proof
3.Nomark:generalsteelquality M: of stainless steel material
HC: general steel quality ^+ hard chromium plating NV:general steel quality ^+ chemical black chromium
(2)Product model of interchangeability linear guide rail
⊚ Single-issue slider product model
⊚ Single-issue guide rail product model
2-3-11 MB series type
(1)Slider type
JSM provides standard type and wide type two straight rail, convenient for customers to choose and use.
| Form | Specifications | Shape | Heightsize (Mm) | Guideraillength (Mm) | Utilityunit |
| Normalized Form | MBN-C MBN-H | Printer 100 Machine arm 8 Electronicinstruments and equipment 16 2000 Semiconductor device | |||
| Widetype | MBW-C MBW-H | 9 个 16 | 100 2000 | ||
(2)Guide rail type
JSM provides locked-type screwhole guiderailforeasy customerinstallation and use.
Table 2-4-2 guide rail type
2-3-12 Accuracy level
Theaccuracyof MBNandMBWseriessmallguiderailis divided into three levels: common, high and precision level. Customerscanchoose suitableaccuracyaccording tothe accuracyrequirementsof theequipment.
(1)Non-interchangeability linear guide rail accurac)
The combined height H measurement is based on the center position of the upper datum of the slider, and the combined width N measurement is based on the center position of the datum of the slider.
unit: mm
| Accuracyclass | Commonlevel(C) | Highlevel(H) | Precisionlevel(P) |
| TolerancesizeerrorforheightH | ± 0.04 | ± 0.02 | ± 0.01 |
| TolerancesizeerrorforwidthN | ± 0.04 | ±0.025 | ±0.015 |
| Mutualerrorof thepairwiseheightH | 0.03 | 0.015 | 0.007 |
| Mutualerror ofpairwisewidths N (referencerail) | 0.03 | 0.02 | 0.01 |
| SlideCfacesthewalkingparallelismoftheguiderailplaneA | Walkparallelism See theform2-4-5 | ||
| ThelideDfaces theguideB | WalkparallelismSeetheform2-4-5 | ||
(2)Exchangeability linear guide rail accuracy
Interchangeability linear rail accuracy in slider assembly in a single rail pair of high and width accuracy, with the interchangeability linear rail accuracy, but if assembled in different branch rail, because of the rail height error, the pair of high and width accuracy,than the exchangeability linearrail accuracy slightly inferior,whilethe parallelismaccuracywith the exchangeabilitylinearrailprecision.
unit:mm
| Accuracyclass | Commonlevel(C) | Highlevel(H) | Precisionlevel(P) |
| TolerancesizeerrorforheightH | ± 0.04 | ±0.02 | ± 0.01 |
| Tolerancesizeerrorforwidth N | ± 0.04 | ±0.025 | ±0.015 |
| Mutualerror of thepairwiseheight H Single pairs | 0.03 | 0.015 | 0.007 |
| Mutual error of pairwise widths N (reference rail) | 0.03 | 0.02 | 0.01 |
| The mutual error of the plural branched pair height H | 0.07 | 0.04 | 0.02 |
| Slide C faces the walking parallelism of the guide rail plane A | WalkparallelismSee theform 2-4-5 | ||
| The lide D faces the guide B | WalkparallelismSeethe form2-4-5 | ||
(3)Walking parallelism accuracy
The walking parallelism of the guide rail C pair A and D pair B is related to the accuracy and length of the guide rail, and itsvaluesarelisted inthefollowingtable.
| Guiderail length (mm) | Accuracylevel (μm)c | Accuracylevel (μm)h | Accuracylevel (μm)p | Guideraillength (mm) | Accuracylevel (μm)c | Accuracy level (μm)h | Accuracylevel (μm)p |
| 50以下 | 12 | 6 | 2 | 1,000~1,200 | 25 | 18 | 11 |
| 20~80 | 13 | 7 | 3 | 1,200~1,300 | 25 | 18 | 11 |
| 80~125 | 14 | 8 | 3.5 | 1,300~1,400 | 26 | 19 | 12 |
| 125~200 | 15 | 6 | 4 | 1,400~1,500 | 27 | 19 | 12 |
| 200~250 | 16 | 10 | 5 | 1,500~1,600 | 28 | 20 | 13 |
| 250~315 | 17 | 11 | 5 | 1,600~1,700 | 29 | 20 | 14 |
| 315~400 | 18 | 11 | 6 | 1,700~1,800 | 30 | 21 | 14 |
| 400~500 | 19 | 12 | 6 | 1,800~1,900 | 30 | 21 | 15 |
| 500~630 | 20 | 13 | 7 | 1,900~2,000 | 31 | 22 | 15 |
| 630~800 | 22 | 14 | 8 | 2,000~ | 31 | 22 | 16 |
| 800~1,000 | 23 | 16 | 9 |
2-3-13 Prepress
eries provides three prepressures: common gap, no prepress, and li
| Prepresslevel | Note | Prepress | Useaccuracy |
| commongap | ZF | Precisionclearance4~10um | C |
| noprepress | ZO | O | C~P |
| lightprepress | ZA | 0.02C | C~P |
2-3-14 Dustproof equipment
The standard dust-proof slider is equipped with oil scraper to prevent dust or impurities from entering the slider, and affect the life and accuracy of the linear guide rail. The dustproof piece is installed at the bottom of the slider to prevent dust or impurities from entering the inside of the slider from the bottom gap of the slider. If the customer wants to choose the dustproof piece,hecanadd +\ \cup code after the model. Specification 5,7 slider to the bottom of the surface gap (H 1) is very small, does not provide additional dustproof plate, but specifications 9,12 and 15 provide dustproof panel selection. When choosing dustproof tablets, customers should pay attention to the decrease of the slider gap (H 1). When the side bearing surface is used, the height of the side bearing surface should not be greater than the clearance value (H 1), so as to avoid the interference of the slider to the side bearing surface during running.
| Model | Dustproof sheet | H,mm | model | Dustproof sheet | H,mm |
| MBN7 | MBW7 | ||||
| MBN9 | 1 | MBW9 | 1.9 | ||
| MBN12 | · | 2 | MBW12 | 2.4 | |
| MBN15 | 3 | MBW15 | 2.4 | ||
| MBN5-O | MBW5-O | ||||
| MBN7-O | MBW7-O | ||||
| MBN9-O | 1.2 | MBW9-O | 1.95 | ||
| MBN12-O | 2 | MBW12-O | 2.45 | ||
| MBN15-O | 3 | MBW15-O | 2.45 |
2-3-15 Install plane error
unit: μm
| Specifications | Prepress | ||
| ZFprepress | ZOprepress | ZAprepress | |
| MB5 | 2 | 2 | 2 |
| MB7 | 3 | 3 | 3 |
| MB9 | 4 | 4 | 3 |
| MB12 | 9 | 9 | 5 |
| MB15 | 10 | 10 | 6 |
unit: μm
Note: The values is proportional to the distance
| Specifications | Prepress | ||
| ZFprepress | ZOprepress | ZAprepress | |
| MB5 | 20 | 20 | 2 |
| MB7 | 25 | 25 | 3 |
| MB9 | 35 | 35 | 6 |
| MB12 | 50 | 50 | 12 |
| MB15 | 60 | 60 | 20 |
单位：mm
| Specifications | Flatnesserror |
| MB5 | 0.015/200 |
| MB7 | 0.025/200 |
| MB9 | 0.035/200 |
| MB12 | 0.050/200 |
| MB15 | 0.060/200 |
2-3-16 Installation precautions
| Specifications | Maximumchamferradius oftheshoulderr,(mm) | Maximumchamferradius oftheshoulderr2（mm) | Shoulderheightofthe guiderailendH1（mm) | Sderendshoulder heightH2（mm) |
| MBN5 | 0.1 | 0.2 | 1.2 | 2 |
| MBN7 | 0.2 | 0.2 | 1.2 | 3 |
| MBN9 | 0.2 | 0.3 | 1.7 | 3 |
| MBN12 | 0.3 | 0.4 | 1.7 | 4 |
| MBN15 | 0.5 | 0.5 | 2.5 | 5 |
| MBW5 | 0.1 | 0.2 | 1.2 | 2 |
| MBW7 | 0.2 | 0.2 | 1.7 | 3 |
| MBW9 | 0.3 | 0.3 | 2.5 | 3 |
| MBW12 | 0.4 | 0.4 | 3 | 4 |
| MBW15 | 0.4 | 0.8 | 3 | 5 |
⊚ Torsionvalue of the guiderail assembly screw
unit:mm
| Specifications | Screwspecifications | Torsional forcevalueN-cm[kgf-cm) | ||
| Ironmaterial | Castingmaterial | Aluminumalloymaterial | ||
| MBN5 | M2x0.4Px6L | 57 (5.9) | 39.2 (4) | 29.4 (3) |
| MBN7 | M2x0.4Px6L | 57 (5.9) | 39.2 (4) | 29.4 (3) |
| MBN9 | M3x0.5Px8L | 186 (19) | 127 (13) | 98 (10) |
| MBN12 | M3x0.5Px8L | 186 (19) | 127 (13) | 98 (10) |
| MBN15 | M3x0.5Px10L | 186 (19) | 127 (13) | 98 (10) |
| MBW5 | M2.5x0.45Px7L | 118 (12) | 78.4 (8) | 58.8 (6) |
| MBW7 | M3x0.5Px6L | 186 (19) | 127 (13) | 98 (10) |
| MBW9 | M3x0.5Px8L | 186 (19) | 127 (13) | 98 (10) |
| MBW12 | M4x0.7Px8L | 392 (40) | 274 (28) | 206 (21) |
| MBW15 | M4x0.7Px10L | 392 (40) | 274 (28) | 206 (21) |
2-3-17 Standard length and maximum length of a single guide rail
Equipped with guide rail standard length stock to supply customer demand. If the customer orders the non-standard length guide,the size of the end surface distance E should not be greater than 1/2P,to prevent the instability of therear end of E, and reduce the accuracy of the linear rail, and do not take a small value (less than Emin) to avoid the bolt hole breaking
L=(n-1)x P+2x E
L :Guide rail length (m) P:Distance between bolt holes (\mathsf{mm}) n :Number of bolt holes E :Distance from bolt hole to end face (mm)
| item | MBNR5 | MBNR7 | MBNR9 | MBNR12 | MBN15 | MBWR5 | MBWR7 | MBWR9 | MBWR12 | MBWR15 |
| standard lengthL(n) | 40 (3) | 40 (3) | 55 (3) | 70 (3) | 70 (2) | 50 (3) | 80 (3) | 80 (3) | 110 (3) | 110 (3) |
| 55 (4) | 55 (4) | 75 (4) | 95 (4) | 110 (3) | 70 (4) | 110 (4) | 110 (4) | 150 (4) | 150 (4) | |
| 70 (5) | 70 (5) | 95 (5) | 120 (5) | 150 (4) | 90 (5) | 140 (5) | 140 (5) | 190 (5) | 190 (5) | |
| 100 (7) | 85 (6) | 115 (6) | 145 (6) | 190 (5) | 110 (6) | 170 (6) | 170 (6) | 230 (6) | 230 (6) | |
| 130 (9) | 100 (7) | 135 (7) | 170 (7) | 230 (6) | 130 (7) | 200 (7) | 200 (7) | 270 (7) | 270 (7) | |
| 160 (11) | 130 (9) | 155 (8) | 195 (8) | 270 (7) | 150 (8) | 260 (9) | 230 (8) | 310 (8) | 310 (8) | |
| 175 (9) | 220 (9) | 310 (8) | 170 (9) | 260 (9) | 350 (9) | 350 (9) | ||||
| 195 (10) | 245 (10) | 350(9] | 290 (10) | 390 (10) | 390 (10) | |||||
| 275 (14) | 270 (11) | 390 (10) | 350 (14) | 430 (11) | 430 (110) | |||||
| 375 (19] | 320 (13) | 430 (11) | 500 (19) | 510 (13) | 510 (13) | |||||
| 370 (15) | 470 (12) | 710 (24) | 590 (19) | 590 (15) | ||||||
| 470 (19) | 550 (14) | 860 (29) | 750 (19) | 750 (19) | ||||||
| 570 (23) | 670 (17) | 910 (23) | 910 (23) | |||||||
| 695 (28) | 870 (22) | 1070 (27) | 1070 (27) | |||||||
| GAP(P) | 15 | 15 | 20 | 25 | 40 | 20 | 30 | 30 | 40 | 40 |
| Standard end distance (Es) | 5 | 5 | 7.5 | 10 | 15 | 5 | 10 | 10 | 15 | 15 |
| Standard end distance to the maximumlength | 250 (17) | 595 (40) | 1195 (60) | 1995 (80) | 1990 (50) | 250 (13) | 590 (20) | 1970 (66) | 1990 (50) | 1990 (50) |
| extremelength | 2504 | 600 | 12005 | 2000 | 2000 | 2506 | 6006 | 2000 | 2000 | 2000 |
Note: 1. The size tolerance of the general guide E is 0.5~-0.5mm and the dimension tolerance of the guide tooth E is 0~-0.3mm 2. The maximum length of the standard end distance refers to the maximum length of the guide rail with the left and right standard end distance.
MB series
Micro small rolling bead linear slide rail
2-3-18 MBN/MBW series linear guide rail size form
(1)MBN-C/MBN-H
| Model | Component size (mm) | Slidersize (mm) | Guidetracksize (mm) | Fixed bolt sizeof the guiderail | Basic dynamid | Basic static rated load rated lood | Allowthe staticmoment | Weight | |||||||||||||||||
| H, | N | W | B | C | G | G | Mxl | H | W | H | D h | d | P | E (mm) | C(kN) | C。(kN) | MR N-m | Mp N-m | M N-m | Slider kg | Guide rail kg/m | ||||
| MBN7C MBN7H | 8 1.5 | 5 | 17 | 12 | 8 2.5 13 | 13.5 21.8 | 22.5 30.8 | Φ1.2 | M2x2.5 | 1.5 | 7 4.8 | 4.2 | 2.3 | 2.4 | 15 5 | M2x6 | 0.93 1.30 | 1.18 1.86 | 4.47 7.26 | 2.70 4.56 | 2.70 4.56 | 0.010 0.015 | 0.22 | ||
| MBN9C | 10 2 | 5.5 | 20 | 15 | 10 2.5 | 18.9 29.9 | 28.9 39.9 | Φ1.4 | M3x3 | 1.8 | 9 6.5 | 6 | 3.5 | 3.5 20 | 7.5 | M3x8 | 1.77 2.42 | 2.42 3.82 | 11.17 18.62 | 6.98 17.69 | 6.98 17.69 | 0.016 | 0.38 | ||
| MBN9H MBN12C | 16 15 21.7 | 34.7 | Φ3 | 2.5 | 2.70 | 3.72 | 24.21 | 13.03 | 13.03 | 0.026 0.034 | |||||||||||||||
| MBN12H | 13 N | 7.5 27 | 20 | 3.5 20 | 32.4 | 45.4 | M3x3.5 | 12 | 8 | 6 | 4.5 3.5 | 25 | 10 M3x8 | 3.53 | 5.59 | 36.31 | 34.45 | 34.45 | 0.054 | 0.65 | |||||
| MBN15C | 16 4 | 8.5 | 25 | 20 3.5 | 26.7 | 42.1 | 4.5 | M3x4 | N 15 | 10 | 6 | 4.5 3.5 | 40 | 15 M3x10 | 4.38 | 5.31 | 42.83 | 20.48 | 20.48 | 0.059 | 1.06 | ||||
| MBN15H | 32 | 25 | 43.4 | 58.8 | Φ3 | 6.05 | 8.65 | 69.83 | 54.93 | 54.93 | 0.092 | ||||||||||||||
MB series
Micro small rolling bead linear slide rail
2-3-18 MBN/MBW series linear guide rail size form
(2）MBW-C/MBW-H
MBW7，MBW9,MAW12
| Model | Component size (mm) | Slidersize (mm) | Guide tracksize (mm) | Fixed bolt size of the guide rail | Basic Basic dynamic static rated load rated load | Allowthe staticmoment | Weight | ||||||||||||||||||
| H H | N | WB | B | C | G G | Mxl | H2 | WWB | H | D | h | d P | E | (mm) | C(KN) | C。(kN) | N-m | Mp N-m | M N-m | Slider kg | Guide rail kg/m | ||||
| MBW7C MBW7H | 1.9 | 5.5 | 25 | 19 | 10 3 | 21 | 31.2 | 1.2 | M3x3 | 1.85 14 | 5.2 | 6 3.2 | 3.5 | 30 | 10 M3x6 | 1.30 1.68 | 1.96 2.98 | 22.28 | 14.92 6.78 | 6.78 14.75 14.75 | 0.020 0.029 | 0.51 | |||
| MBW9C | 21 | 4.5 | 19 30.8 12 27.5 | 41 39.3 | 2.4 | 7 | 30 | M3x8 | 2.61 | 3.91 | 38.11 | 18.01 | 18.01 | 0.040 | |||||||||||
| MBW9H | 12 2.9 | 6 30 | 23 | 3.5 | 24 38.5 | 50.7 | Φ1.2 | M3x3 | 18 | 6 | 4.5 | 3.5 | 10 | 3.26 | 5.60 | 51.81 | 32.30 | 32.30 | 0.057 | 16'0 | |||||
| MBW12C | 14 3.4 | 8 | 40 | 28 | 15 | 31.3 | 46.1 | Φ1.2 | M3x3.6 | 24 | 8.5 8 | 4.5 | 4.5 40 | 15 | M4x8 | 3.72 | 5.31 | 66.82 | 26.41 | 26.41 | 0.071 | 1.49 | |||
| MBW12H | 28 | 45.6 | 60.4 | 2.8 | 4.85 | 7.83 | 97.57 | 54.50 | 54.50 | 0.103 | |||||||||||||||
| MBW15C | 16 3.4 | 6 | 45 | 20 7.5 | 38 | 54.8 | 5.2 M3 | M4x4.2 | 3.2 | 42 | 23 9.5 | 8 | 4.54.5 | 40 | 15 | M4x10 | 6.43 | 8.76 | 189.37 | 53.83 | 53.83 | 0.143 | 2.86 | ||
| MBW15H | 60 | 35 | 57 | 73.8 | 8.48 | 12.71 | 284.06 | 116.47 | 116.47 | 0.215 | |||||||||||||||
MB series
Micro small rolling bead linear slide rail
2-3-18 MBN/MBW series linear guide rail size form
(3）MBN-C-O/MBN—O
| Model | Component size (mm) | Slidersize (mm) | Guidetracksize (ww) | Fixedpolt Basic size ofthedynamid guiderail rated loadrated load | Basic static | Allowthe staticmoment | Weight | |||||||||||||||||
| H H | N W | B | B | C | L | G | G | Mxl | H W | H | D | h p | P | E | (mm) | C(KN) | C。(kN) | MR N-m | Mp N-m | M N-m | Slider kg | Guide rail kg/m | ||
| MBN5C-0 | 8 | 2 | 9.6 | 16 | M2x1.5 | 0.51 | 0.80 | 1.90 | 1.24 | 1.24 | 0.003 | |||||||||||||
| MBN5H-0 | 6 | 1.5 3.5 | 12 | 8 | 2 | 12.6 | 19 | 0.8 | M2x1.5 1 | 5 | 3.63.60.82.415 | 5 | M2x6 | 0.64 | 1.03 | 2.47 | 2.19 | 2.19 | 0.004 | 0.15 | ||||
| MBN5HL-0 | 一 | 6 7 | 12.6 | 19 | M2.6-THRU | 0.64 | 1.03 | 2.47 | 2.19 | 2.19 | 0.004 | |||||||||||||
| MBN7C-0 | 1.5 | 5 | 12 | 2.5 | 8 13.5 | 22.5 | Φ1.2 | M2x2.5 | 7 | 4.84.22.3 2.4 | 15 | M2x6 | 0.93 | 1.18 | 4.47 | 2.70 | 2.70 | 0.008 | 0.22 | |||||
| MBN7H-0 | 8 | 17 | 12 | 2.5 13 | 21.8 | 30.8 | M2x2.5 | 1.5 | 5 | 1.30 | 1.86 | 7.26 | 4.56 | 4.56 | 0.012 | |||||||||
| MBN9C-0 | 10 2.2 | 5.5 | 20 | 15 | 2.5 10 | 19.4 | 30 | 一 | M3x3 Φ1.4 | 1.8 | 9 | 6.5 | 3.53.520 | 7.5 | M3x8 | 1.91 | 2.70 | 12.40 | 8.52 | 8.52 | 0.012 | 0.38 | ||
| MBN9H-0 | 15 | 2.5 16 | 29.3 | 39.9 | M3x3 | 2.38 | 3.73 | 18.72 | 20.40 | 20.40 | 0.02 | |||||||||||||
| MBN12C-0 | 13 3 | 7.5 | 27 | 20 | 3.5 15 | 22 | 35 | Φ2 | M3x3.5 | 2.5 | 12 | 8 6 | 4.5 | 3.5 25 | 10 | M3x8 | 2.70 | 3.72 | 24.21 | 13.03 | 13.03 | 0.025 | 0.65 | |
| MBN12H-0 | 20 | 3.5 20 | 34.6 | 47.6 | M3x3.5 | 4.06 | 5.61 | 36.48 | 35.62 | 35.62 | 0.047 | |||||||||||||
| MBN15C-0 | 16 4 | 8.5 | 32 | 25 | 3.5 20 | 26.7 | 41.3 | 4.50 | M3x4 M3 | 3 | 15 | 10 6 | 4.5 | 3.5 40 | 15 | M3×10 | 4.38 | 5.31 | 42.83 | 20.48 | 20.48 | 0.057 | 1.06 | |
| MBN15H-0 | 25 | 3.5 25 | 43.4 | 58 | M3x4 | 6.05 | 8.65 | 69.83 | 54.93 | 54.93 | 0.088 | |||||||||||||
MB series
Micro small rolling bead linear slide rail
2-3-18 MBN/MBW series linear guide rail size form
(4）MBW-C-O/MBW-H-O
| Model | Component size (ww) | Slidersize (mm) | Guide tracksize (mm) | Fixed bolt Basic size of the dynamic guiderail rated load | Basic static rated load | Allowthe staticmoment | Weight | |||||||||||||||||||
| H | H | N | WB | B | C | L G | G | Mxl | H2 | WW | H | D h | d | P | E | (mm) | C(KN) | C,(kN) | MR N-m | Mp N-m | My N-m | Slider kg | Guide rail kg/m | |||
| MBW5V-0 | 6.5 | 1.5 | 3.5 17 | 13 | 2 | 一 | 14.1 | 20.5 | 0.8 | M2.5x1.5 | 10 | 4 | 5.5 | 1.6 | 3 | 20 | M2.5x7 | 0.65 | 1.12 | 5.23 | 2.57 | 2.57 | 0.006 | 0.34 | ||
| MBW5CL-0 | 8.5 | 6.5 | 14.1 | 20.5 | M3-THRU | 0.65 1.30 | 1.12 1.96 | 5.23 14.92 | 2.57 6.78 | 2.57 6.78 | 0.006 0.018 | |||||||||||||||
| MBN7C-0 | 9 | 1.9 | 5.5 | 19 25 19 | N | 10 | 21 31.2 30.8 | 41 | Φ1.2 | M3x3 M3x3 | 1.85 | 14 | 5.2 | 6 | 3.23.5 | 10 | M3x6 | 1.68 | 2.98 | 22.28 | 14.75 | 14.75 | 0.026 | 0.51 | ||
| MBN7H-0 | 21 | 3 4.5 | 19 12 | 27.5 | 39.7 | M3x3 | 2.61 | 3.91 | 38.11 | 18.01 | 18.01 | 0.038 | ||||||||||||||
| MBN9C-0 MBN9H-0 | 12 | 2.95 | 6 30 | 23 | 3.5 | 24 | 38.5 50.7 | Φ1.2 | M3x3 | 2.65 | 7 | 6 | 4.53.5 | 30 | 10 | M3x8 | 3.26 | 5.60 | 51.81 | 32.30 | 32.30 | 0.053 | 160 | |||
| MBN12C-0 | 28 | 6 | 15 | 31.3 | 45.1 | M3x3.6 | 3.72 | 5.31 | 66.82 | 26.41 | 26.41 | 0.066 | ||||||||||||||
| MBN12H-0 | 14 | 3.45 | 8 40 | 28 | 6 | 28 | 45.6 59.4 | Φ1.2 | M3x3.6 | 2.8 24 | 8.5 | 8 | 4.54.5 | 4015 | M4x8 | 4.85 | 7.83 | 97.57 | 54.50 | 54.50 | 0.093 | 1.49 | ||||
| MBN15C-0 | 45 | 7.5 | 20 | 38 53.8 | M4x4.2 | 6.43 | 8.76 | 189.37 | 53.83 | 53.83 | 0.138 | |||||||||||||||
| MBN15H-0 | 16 | 3.45 | 6 60 | 45 | 7.5 | 35 | 57 | 5.2 72.8 | M3 | M4x4.2 | 3.2 42 | 23 | 9.5 | 8 | 4.5 4.5 | 40 | 15 | M4x10 | 8.48 | 12.71 | 284.06 | 116.47 | 116.47 | 0.200 | 2.86 | |
Professional production of linear guide system
