该页无缩略图
| 型号名Model | ITY-□-□AT | ITY-□-□NAT/NBT/PA/PBT | ITY-□-□KAT/KBT |
| 应差距离 Hysteresis | 检测距离的10%以下 Max10% Of sensing distance | ||
| 电源电源(使用电压范围)Power supply (Operating voltage) | 12-24VDC (10-30VDC) | 12-24VDC (10-30VDC) | 24-250VAC |
| 漏电流Leakage current | 0.6mA以下Max.0.6mA | 1.0mA以下Max1.0mA | 2.5mA以下Max.2.5mA |
| 残留电压Residual voltage | 3.5V以下Max.3.5V | 1.0V以下Max.1.0V | 1.0V以下Max.1.0V |
| 温度的影响Affection by temp. | 在-25~+70℃温度范围内+20℃时的检测距离的±10%以内 Max. ± 10% for sensing distance at ambient temperature 20℃ | ||
| 控制输出Control output | 2~100mA | 200mA以下Max.200mA | 5~150mA 5~200mA |
| 绝缘阻抗Insulation resistance | 50MΩ以上(500VDC为基准)Min.50MΩ(at 500VDC megger) | ||
| 耐电压Dielectric strength | 1500VAC50/60Hz 1分钟 1500VAC50/60Hz for 1 minute | ||
| 耐振动Vibration | 10~55Hz(周期1分钟)振幅1mmX，Y，Z各方向2小时1mm amplitude at frequency of 10 to 55Hz(for 1 min)in each of X,Y,Z directions for 2 hours | ||
| 耐冲击Shock | 500m/s2 (50G)X, Y,Z各方向3次 500m/s² (approx.50G)X, Y, Z directions for 3 times | ||
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) | ||
| 使用周围温度Ambient temperature | -25~+70℃(未结冰状态Noicing) | ||
| 储存温度Storage temperature | -30~+80℃(未结冰状态Noicing) | ||
| 使用周围湿度Ambient humidity | 35~95%RH(未结露状态No condensation) | ||
| 保护电路Protection circuit | 浪涌保护电路/过载&短路保护Surge protection circuit, Overcurrent protection | 内置浪涌保护、电源反接保护电路、过流保护电路Surge protection circuit,Reverse polarity protection circuit,overcurrent protection circuit | 内置浪涌保护Surge protection circuit |
| 材质Material | 外壳/螺母：镀镍黄铜，垫片：镍镀铁，检测面：耐热ABSCase/Nut: Nickel plated Brass,Washer: Nickel plated Iron,Sensing surface:Heat-resistantABS | ||
| 认证/防护等级Approval/Protection | CE\ROHS\ISO9001 IP67(IEC规格 Standard) | ||
外形尺寸DimensionsITY12-02T
ITY12-04T
ITY18-05T
ITY18-08T
ITY30-10T
ITY30-15T
N.O.type的② ③与N.C.Tyep的③ ④为N.C(Not Connected)端子。
请使用IEC规格的接插头。
of N.O. type and ofN.C. type are not used terminals.
Please use the IEC specifications of the plug.
输出电路 Control Output Diagram
直流2线式 DC2-wire type
直流3线式 DC3-wire type
直流2线式 AC 2-wire type
※ When using DC 3-wire type of connector cable, black (12-24VDC)and blue(ov) cables can be used.
连接器接线图 Wiring Diagram
直流2线式(标准型)DC2-wire type (Standard type)
当使用直流3线连接电缆时，黑线作为(24VDC)及蓝线作为(OV)使用。
直流2线式(IEC规格)DC2-wire type (IECStandard type)
直流3线式DC3-wire type
Please fasten the cleat of connector not to shown the thread.(0.39 to 0.47N.m) Please fasten the vibration part with Teflon tape.
交流2线式 AC2-wire type
交流开闭型时，②与③，①与④内部是相连接的。
正确使用 Proper usage
相互干扰 Mutual-interferece
当把两个以上的接近开关一起安装使用时，可能会发生相互干扰引起的误动作，在安装时请务必满足下表中所规定的尺寸要求进行安装。
When several proximity sensors are mounted close to one another a malfunction of the sensor may be caused due to mutual interference. Therefore, be sure to provide a minimun distance between the two sensors as below chart indicates.
周围金属的影响 Influence by surrounding metals
当接近传感器周围有金属存在时，为防止复位不正常等误差发生，安装时请满足下表中所规定的尺寸要求进行安装。
When sensors are mounted on metallic panel, you must prevent the sensors from being affected by any metallic object except target. Therefore, be sure to provide a minimum distance as below chart indicates.
| 型号名Model项目Item | ITY12-02T | ITY12-04T | ITY18-05T | ITY18-08T | ITY30-10T | ITY30-15T |
| A | 12 | 24 | 30 | 48 | 60 | 90 |
| B | 24 | 36 | 36 | 54 | 60 | 90 |
| C | 0 | 11 | 0 | 14 | 0 | 15 |
| φd | 12 | 36 | 18 | 54 | 30 | 90 |
| m | 6 | 12 | 15 | 24 | 30 | 45 |
| n | 18 | 36 | 27 | 545 | 45 | 90 |
规格 SpecificationS
| 可选型号Optional model | 检测距离Sensing distance | Sta标准检测物arget | 设定距离Setting distance | 应答频率(1)Response frequency(1) | 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) |
| ITY12-02LAT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY30-10NAT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY12-04LAT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY30-10NBT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY18-05LAT | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 500Hz | ITY30-10PAT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY18-08LAT | 8mm | 25×25×1mm(铁Iron) | 0~5.6mm | 350Hz | ITY30-10PBT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY30-10LAT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz | ITY30-15NAT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY30-15LAT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz | ITY30-15NBT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY12-02NAT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY30-15PAT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY12-02NBT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY30-15PBT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY12-02PAT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY12-02KAT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 20Hz |
| ITY12-02PBT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY12-02KBT | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 20Hz |
| ITY12-04NAT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY12-04KAT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 20Hz |
| ITY12-04NBT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY12-04KBT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 20Hz |
| ITY12-04PAT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY18-05KAT | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 20Hz |
| ITY12-04PBT | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY18-05KBT | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 20Hz |
| ITY18-05NAT | 5mm | 18 ×18 × 1mm(铁Iron) | 0~3.5mm | 500Hz | ITY18-08KAT | 8mm | 25 × 25× 1mm(铁Iron) | 0~5.6mm | 20Hz |
| ITY18-05NBT | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 500Hz | ITY18-08KBT | 8mm | 25×25×1mm(铁Iron) | 0~5.6mm | 20Hz |
| ITY18-05PAT | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 500Hz | ITY30-10KAT | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 20Hz |
| ITY18-05PBT | 5mm | 18 ×18×1mm(铁Iron) | 0~3.5mm | 500Hz | ITY30-10KBT | 10mm | 30× 30× 1mm(铁Iron) | 0~7mm | 20Hz |
| ITY18-08NAT | 8mm | 25×25×1mm(铁Iron) | 0~5.6mm | 350Hz | ITY30-15KAT | 15mm | 45 ×45 ×1mm(铁Iron) | 0~10.5mm | 20Hz |
| ITY18-08NBT | 8mm | 25 × 25× 1mm(铁Iron) | 0~5.6mm | 350Hz | ITY30-15KBT | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 20Hz |
| ITY18-08PAT | 8mm | 25×25× 1mm(铁Iron) | 0~5.6mm | 350Hz | |||||
| ITY18-08PBT | 8mm | 25 ×25× 1mm(铁Iron) | 0~5.6mm | 350Hz | |||||
| 型号名Model | ITY-□-□LRA | ITY-□-□NAR/NBR/PAR/PBR | ITY-□-□KAR/KBR |
| 应差距离Hysteresis | 检测距离的10%以下 Max10% Of sensing distance | ||
| 电源电源(使用电压范围)Power supply (Operating voltage) | 12-24VDC (10-30VDC) | 12-24VDC(10-30VDC) | 24-250VAC |
| 漏电流Leakage current | 0.6mA以下Max.0.6mA | 1.5mA以下Max.1.5mA | 2.5mA以下Max.2.5mA |
| 残留电压Residual voltage | 3.5V以下Max.3.5V | 1.0V以下Max.1.0V | 10V以下Max.10V |
| 温度的影响Affection by temp. | 在-25~+70℃温度范围内+20℃时的检测距离的 ± 10%以内 Max. ± 10% for sensing distance at ambient temperature 20℃ | ||
| 控制输出Control output | 2~100mA | 200mA以下Max.200mA | 5~150mA 5~200mA |
| 绝缘阻抗Insulation resistance | 50MΩ以上(500VDC为基准)Min.50MΩ(at 500VDC megger) | ||
| 耐电压Dielectric strength | 1500VAC50/60Hz 1分钟 1500VAC50/60Hz for 1 minute | ||
| 耐振动Vibration | 10~55Hz(周期1分钟)振幅1mmX，Y.Z各方向2小时1mm amplitude at frequency of 10 to 55Hz(for 1 min)in each of X,Y,Z directions for 2 hours | ||
| 耐冲击Shock | 500m/s2 (50G)X, Y,Z 各方向3次 500m/s2 (approx.50G)X, Y, Z directions for 3 times | ||
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) | ||
| 使用周围温度Ambient temperature | -25~+70℃(未结冰状态Noicing) | ||
| 储存温度Storage temperature | -30~+80℃(未结冰状态Noicing) | ||
| 使用周围湿度Ambient humidity | 35~95%RH(未结露状态No condensation) | ||
| 保护电路Protection circuit | 内置浪涌保护、电源反接保护电路、过流保护电路Surge protection circuit,Reverse polarity protection circuit, overcurrent protection circuit | 内置浪涌保护Surge protection circuit | |
| 材质Material | 外壳/螺母：镀镍黄铜，垫片：镍镀铁，检测面：耐热ABS，一般线缆(灰色)：聚氯乙烯(PVC)，耐油性线缆(灰色)：聚氯乙烯(耐油强化型PVC)Case/Nut: Nickel plated Brass,Washer: Nickel plated Iron,Sensing surface:Heat-resistantABS, Standard cable(Gray): Polyvinyl chloride (PVC),Oil resistant cable(Gray):Oil resistant Polyvinyl chloride(PVC) | ||
| 认证/防护等级Approval/Protection | CE\ROHS\ISO9001 IP67(IEC规格 Standard) | ||
外形尺寸Dimensions
ITY12-02R
输出电路 Control Output Diagram
直流2线式 DC2-wire type
直流3线式 DC3-wire type
直流2线式 AC 2-wire type
直流2线式(标准型)DC2-wire type (Standard type)
When using DC 3-wire type of connector cable, black (12-24VDC)and blue(ov) cables can be used.
连接器接线图Wiring Diagram
直流2线式(IEC规格)DC2-wire type (IECStandard type)
N.O.type的② ③与N.C.Tyep的③ ④为N.C(Not Connected)端子。请使用IEC规格的接插头。
直流3线式DC3-wire type
结合接插头时，请使用(0.39\~0.49N.M拧紧螺丝)。在发生震动的地方请用胶带缠住连接线缆后使用。Please fasten the cleat of connector not to shown the thread.(0.39 to 0.47N.m)Please fasten the vibration part with Teflon tape.
正确使用 Proper usage
交流2线式AC2-wire type
交流开闭型时，②与③，①与④内部是相连接的。
When several proximity sensors are mounted close to one another a malfunction of the sensor may be caused due to mutual interference. Therefore, be sure to provide a minimun distance between the two sensors as below chart indicates.
当把两个以上的接近开关一起安装使用时，可能会发生相互干扰引起的误动作，在安装时请务必满足下表中所规定的尺寸要求进行安装。
相互干扰 Mutual-interferece
周围金属的影响 Influence by surrounding metals
当接近传感器周围有金属存在时，为防止复位不正常等误差发生，安装时请满足下表中所规定的尺寸要求进行安装。
When sensors are mounted on metallic panel, you must prevent the sensors from being affected by any metallic object except target. Therefore, be sure to provide a minimum distance as below chart indicates.
| 型号名Mode项目Item | ITY12-02R | ITY12-04R | ITY18-05R | ITY18-08R | ITY30-10R | ITY30-15R |
| A | 12 | 24 | 30 | 48 | 60 | 90 |
| B | 24 | 36 | 36 | 54 | 60 | 90 |
| C | 0 | 11 | 0 | 14 | 0 | 15 |
| φd | 12 | 36 | 18 | 54 | 30 | 90 |
| m | 6 | 12 | 15 | 24 | 30 | 45 |
| n | 18 | 36 | 27 | 54 | 45 | 90 |
规格 SpecificationS
| 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离 | 应答频率(1)Response frequency(1) | 可选型号Optional model | 检测距离Sensing distance | 标准检测物target | 设定距离 | 应答频率(1)Response frequency(1) |
| ITY08-01LA | 1.5mm | 8×8×1mm (铁 Iron) | 0~1.05mm | 1.5kHz | ITY18-08NA | 8mm | 25×25×1mm(铁Iron) | 0~5.6mm | 350Hz |
| ITY08-02LA | 2mm | 8×8×1mm(铁Iron) | 0~1.4mm | 1kHz | ITY18-08NB | 8mm | 25 × 25× 1mm(铁Iron) | 0~5.6mm | 350Hz |
| ITY12-02LA | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY18-08PA | 8mm | 25×25 ×1mm(铁Iron) | 0~5.6mm | 350Hz |
| ITY12-04LA | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY18-08PB | 8mm | 25 ×25 × 1mm(铁Iron) | 0~5.6mm | 350Hz |
| ITY18-05LA | 5mm | 18×18× 1mm(铁Iron) | 0~3.5mm | 500Hz | ITY30-10NA | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY18-08LA | 8mm | 25 ×25 × 1mm(铁Iron) | 0~5.6mm | 350Hz | ITY30-10NB | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY30-10LA | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz | ITY30-10PA | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY30-15LA | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz | ITY30-10PB | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 400Hz |
| ITY08-01NA | 1mm | 8×8×1mm(铁Iron) | 0~1.05mm | 1.5kHz | ITY30-15NA | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY08-01NB | 1mm | 8×8×1mm(铁Iron) | 0~1.05mm | 1.5kHz | ITY30-15NB | 15mm | 45 ×45× 1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY08-01PA | 1mm | 8×8×1mm(铁Iron) | 0~1.05mm | 1.5kHz | ITY30-15PA | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY08-01PB | 1mm | 8×8×1mm(铁Iron) | 0~1.05mm | 1.5kHz | ITY30-15PB | 15mm | 45×45×1mm(铁Iron) | 0~10.5mm | 200Hz |
| ITY08-02NA | 2mm | 8×8×1mm(铁Iron) | 0~1.4mm | 1kHz | ITY12-02KA | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 20Hz |
| ITY08-02NB | 2mm | 8×8×1mm(铁Iron) | 0~1.4mm | 1kHz | ITY12-02KB | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 20Hz |
| ITY08-02PA | 2mm | 8×8×1mm(铁Iron) | 0~1.4mm | 1kHz | ITY12-04KA | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 20Hz |
| ITY08-02PB | 2mm | 8×8×1mm(铁Iron) | 0~1.4mm | 1kHz | ITY12-04KB | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 20Hz |
| ITY12-02NA | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY18-05KA | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 20Hz |
| ITY12-02NB | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY18-05KB | 5mm | 18× 18×1mm(铁Iron) | 0~3.5mm | 20Hz |
| ITY12-02PA | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY18-08KA | 8mm | 25 ×25 × 1mm(铁Iron) | 0~5.6mm | 20Hz |
| ITY12-02PB | 2mm | 12×12×1mm(铁Iron) | 0~1.4mm | 1.5kHz | ITY18-08KB | 8mm | 25 × 25× 1mm(铁Iron) | 0~5.6mm | 20Hz |
| ITY12-04NA | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY30-10KA | 10mm | 30×30×1mm(铁Iron) | 0~7mm | 20Hz |
| ITY12-04NB | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz ITY30-10KB | 10mm | 30 ×30×1mm(铁Iron) | 0~7mm | 20Hz | |
| ITY12-04PA | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz ITY30-15KA | 15mm | 45× 45×1mm(铁Iron) | 0~10.5mm | 20Hz | |
| ITY12-04PB | 4mm | 12×12×1mm(铁Iron) | 0~2.8mm | 500Hz | ITY30-15KB | 15mm | 45 ×45× 1mm(铁Iron) | 0~10.5mm | 20Hz |
| ITY18-05NA | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 500Hz | |||||
| ITY18-05NB | 5mm | 18× 18 ×1mm(铁Iron) | 0~3.5mm | 500Hz | |||||
| ITY18-05PA | 5mm | 18× 18 × 1mm(铁Iron) | 0~3.5mm | 500Hz | |||||
| ITY18-05PB | 5mm | 18× 18 × 1mm(铁Iron) | 0~3.5mm | 500Hz | |||||
特点 Features
| 内置浪涌保护，电源反接保护和过流保护电路 | IBuilt-in surge protection, reverse polarity protection, Overcurrent Protection circuit |
| 寿命长，高可靠性，操作简单，经济实惠 | Long life cycle and high reliability |
| 红色LED状态指示灯，易于识别运行状态 | Red LED status indication |
| IP67防护等级(IEC规格) | Protection structure IP67(IEC standard) |
| 可以代替微动开关或限位开关广泛使用 | Replaceable for micro switches and limit switches |
| 型号名Model | ITF-□-□LA | ITF-□-□NA/PA/NB/PB | ITF-□-□KA/KB |
| 应差距离Hysteresis | 检测距离的10%以下 Max10% Of sensing distance | ||
| 电源电源(使用电压范围)Power supply (Operating voltage) | 12-24VDC (10-30VDC) | 12-24VDC(10-30VDC) | 100-240VAC(86-264VAC) |
| 漏电流Leakage current | 0.6mA以下Max.0.6mA | 10mA以下Max.10mA | 10V以下Max.10V |
| 残留电压Residual voltage | 1.0V以下Max.1.0V | 1.0V以下Max.1.0V | 3.5V以下Max.3.5V |
| 温度的影响Affection by temp. | 在-25~+70℃温度范围内+20℃时的检测距离的 ± 10%以内 Max. ± 10% for sensing distance at ambient temperature 20℃ | ||
| 控制输出Control output | 2~100mA | 200mA | 200mA |
| 绝缘阻抗Insulation resistance | 50MΩ以上(500VDC为基准)Min.50MΩ(at 500VDC megger) | ||
| 耐电压Dielectric strength | 1500VAC50/60Hz 1分钟 1500VAC50/60Hz for 1 minute | ||
| 耐振动Vibration | 10~55Hz(周期1分钟)振幅1mmX，Y.Z各方向2小时1mm amplitude at frequency of 10 to 55Hz(for 1 min)in each of X,Y,Z directions for 2 hours | ||
| 耐冲击Shock | 500m/s2 (50G)X, Y,Z各方向3次 500m/s2 (approx.50G)X, Y, Z directions for 3 times | ||
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) | ||
| 使用周围温度Ambient temperature | -25~+70℃(未结冰状态Noicing) | ||
| 储存温度Storage temperature | -30~+80℃(未结冰状态Noicing) | ||
| 使用周围湿度Ambient humidity | 35~95%RH(未结露状态No condensation) | ||
| 保护电路Protection circuit | 内置浪涌保护、电源反接保护电路、过流保护电路Surge protection circuit,Reverse polarity protection circuit, overcurrent protection circuit | 内置浪涌保护Surge protection circuit | |
| 材质Material | 外壳/螺母：镀镍黄铜，垫片：镍镀铁，检测面：耐热ABS，一般线缆(灰色)：聚氯乙烯(PVC)，耐油性线缆(灰色)：聚氯乙烯(耐油强化型PVC)Case/Nut: Nickel plated Brass,Washer: Nickel plated Iron,Sensing surface:Heat-resistantABS, Standard cable(Gray): Polyvinyl chloride (PVC),Oil resistant cable(Gray):Oil resistant Polyvinyl chloride(PVC) | ||
| 认证/防护等级Approval/Protection | CE\ROHS\ISO9001 IP67(IEC规格 Standard) | ||
(1)开关动作的应答频率为平均值。测定条件使用标准检测物，检测物的间距为标准检测物的2倍，设定距离为检测距离的1/2 (1)The response frequency is the average value.the standard sensing target is used and the width is set as 2 times of the standard sensing target, 1/2 of the sensingdistance for the distance
输出电路 Control Output Diagram
直流2线式 DC2-wire type
直流3线式 DC3-wire type
直流2线式 AC 2-wire type
连接 Connections
直流2线式 DC 2-wire type<br>交流2线式 AC 2-wire type
负载可以连接 任意一根线 The load can be connected to either wire.
负载可以连接 任意一根线 The load can be connected to either wire.
直流3线式 DC 3-wire type
PA12,可选择NPN/PNP There is NPN/PNPselection switch in PA-12.
正确使用 Proper usage
相互干扰Mutual-interferece
当几个接近传感器安装在一起，会发生相互干扰引起传感器故障，一般两个传感器之间的间隔的距离如图
When several proximity sensors are mounted close to one another a malfunction ofthe may be caused due to mutual interferece.Therefore, be sure to provide a minimum distance between the tweo sensors as below chart indicates.
| 型号名Model项目Item | ITF17-05 | ITF18-05 | ITF25-07 | ITF30-10 | ITF40–15 |
| A | 30 | 48 | 30 | 60 | 120 |
| B | 36 | 40 | 40 | 50 | 70 |
| C | 5 | 5 | 5 | 5 | 5 |
| φd | 15 | 24 | 15 | 30 | 60 |
| e | 24 | 33 | 25 | 30 | 45 |
| m | 18 | 20 | 20 | 25 | 35 |
规格 Specifications
| 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) | 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) |
| ITF17-05LA | 5mm | 18 ×18 ×1mm(铁Iron) | 0~3.5mm | 700Hz | ITF30-10NA | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 250Hz |
| ITF18-05LA | 5mm | 25 × 25 × 1mm(铁Iron) | 0~3.5mm | 200Hz | ITF30-10PA | 10mm | 40 × 40 × 1mm(铁Iron) | 0~7.5mm | 250Hz |
| ITF25-07LA | 7mm | 30×30×1mm(铁Iron) | 0~5.5mm | 350Hz | ITF30-10NB | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 250Hz |
| ITF30-10LA | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 250Hz | ITF30-10PB | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 250Hz |
| ITF40-15LA | 15mm | 60×60×1mm(铁Iron) | 0~12.5mm | 100Hz | ITF40-15NA | 15mm | 60×60×1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF17-05NA | 5mm | 18 ×18 ×1mm(铁Iron) | 0~3.5mm | 700Hz | ITF40-15PA | 15mm | 60×60×1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF17-05PA | 5mm | 18 ×18 ×1mm(铁Iron) | 0~3.5mm | 700Hz | ITF40-15NB | 15mm | 60×60×1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF17-05NB | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 700Hz | ITF40-15PB | 15mm | 60×60×1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF17-05PB | 5mm | 18×18×1mm(铁Iron) | 0~3.5mm | 700Hz | ITF25-07KA | 7mm | 30×30×1mm(铁Iron) | 0~5.5mm | 20Hz |
| ITF18-05NA | 5mm | 25 × 25 × 1mm(铁Iron) | 0~3.5mm | 200Hz | ITF25-07KB | 7mm | 30 × 30 × 1mm(铁Iron) | 0~5.5mm | 20Hz |
| ITF18-05PA | 5mm | 25×25×1mm(铁Iron) | 0~3.5mm | 200Hz | ITF30-10KA | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 20Hz |
| ITF18-05NB | 5mm | 25×25×1mm(铁Iron) | 0~3.5mm | 200Hz | ITF30-10KB | 10mm | 40×40×1mm(铁Iron) | 0~7.5mm | 20Hz |
| ITF18-05PB | 5mm | 25 × 25 × 1mm(铁Iron) | 0~3.5mm | 200Hz | ITF40-15KA | 15mm | 60× 60× 1mm(铁Iron) | 0~12.5mm | 20Hz |
| ITF25-07NA | 7mm | 30 ×30 × 1mm(铁Iron) | 0~5.5mm | 350Hz | ITF40-15KB | 15mm | 60 × 60 ×1mm(铁Iron) | 0~12.5mm | 20Hz |
| ITF25-07PA | 7mm | 30×30×1mm(铁Iron) | 0~5.5mm | 350Hz | |||||
| ITF25-07NB | 7mm | 30×30×1mm(铁Iron) | 0~5.5mm | 350Hz | |||||
| ITF25-07PB | 7mm | 30 ×30× 1mm(铁Iron) | 0~5.5mm | 350Hz | |||||
规格 Specifications
| 型号名Model | ITF-□-□LA/NA/PA/NB/PB |
| 应差距离 Hysteresis | 检测距离的10%以下 Max 10% Of sensing distance |
| 电源电源(使用电压范围)Power supply (Operating voltage) | 10-30VDC |
| 漏电流Leakage current | 10mA以下Max.10mA |
| 残留电压Residual voltage | DC:15V以下Max.3.5V |
| 温度的影响Affection by temp. | 在-25~+70℃温度范围内+20℃时的检测距离的 ± 10%以内 Max. ± 10% for sensing distance at ambient temperature 20℃ |
| 控制输出Control output | 5~200mA |
| 绝缘阻抗Insulation resistance | 50MΩ以上(500VDC为基准)Min.50MΩ(at 500VDC megger) |
| 耐电压Dielectric strength | 1500VAC50/60Hz 1分钟 1500VAC50/60Hz for 1 minute |
| 耐振动Vibration | 10~55Hz(周期1分钟)振幅1mmX，Y，Z各方向2小时1mm amplitude at frequency of 10 to 55Hz(for 1 min)in each of X,Y,Z directions for 2 hours |
| 耐冲击Shock | 500m/s² (50G)X, Y,Z 各方向3次 500m/s² (approx.50G)X, Y, Z directions for 3 times |
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) |
| 使用周围温度Ambient temperature | -25~+70℃(未结冰状态Noicing) |
| 储存温度Storage temperature | -30~+80℃(未结冰状态Noicing) |
| 使用周围湿度Ambient humidity | 35~95%RH(未结露状态No condensation) |
| 保护电路Protection circuit | 浪涌保护电路，过载&短路保护电路，过电流保护电路Surge protection circuit, Reverse polarity protection circuit, Overcurrent protection circuit |
| 材质Material | 外壳：耐热ABS，一般线缆(深灰色)：聚氯乙烯(PVC)，Case/Nut: Heat-resistantABS, Standard cable(Gray): Polyvinyl chloride (PVC) |
| 认证/防护等级Approval/Protection | CE\ROHS\ISO9001 IP67(IEC规格 Standard) |
| 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) | 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) |
| ITF10-05LA | 5mm | 25 × 25 × 1mm(铁 Iron) | 0~3.5mm | 200Hz | ITF11-05NB | 5mm | 25 × 25 × 1mm(铁Iron) | 0~3.5mm | 200Hz |
| ITF10-05NA | 5mm | 0~3.5mm | ITF11-05PB | 5mm | 0~3.5mm | ||||
| ITF10-05PA | 5mm | 0~3.5mm | ITF12-07LA | 5mm | 0~5.5mm | ||||
| ITF10-05NB | 5mm | 0~3.5mm | ITF12-07NA | 5mm | 0~5.5mm | ||||
| ITF10-05PB | 5mm | 0~3.5mm | ITF12-07PA | 5mm | 0~5.5mm | ||||
| ITF11-05LA | 5mm | 0~3.5mm | ITF12-07NB | 5mm | 0~5.5mm | ||||
| ITF11-05NA | 5mm | 0~3.5mm | ITF12-07PB | 5mm | 0~5.5mm | ||||
| ITF11-05PA | 5mm | 0~3.5mm |
外形尺寸 Dimensions
输出电路 Control Output Diagram
直流2线式 DC2-wire type
直流3线式 DC3-wire type
正确使用 Proper usage
相互干扰Mutual-interferece
当几个接近传感器安装在一起，会发生相互干扰引起传感器故障，一般两个传感器之间的间隔距离如图
When several proximity sensors are mounted close to one another a malfunction of the sensor may be caused due to mutual interference. Therefore, be sure to provide a minimun distance between the two sensors as below chart indicates.
相对安装Face to Face
并行安装Parallel
周围金属的影响Influence by surrounding metals
当传感器安装在金属面板时，你必须要预防被检测物以外的金属物体因此，要设定最小的间隔距离如图
When sensors are mounted on metallic panel, you must prevent the sensors from being affected by any metallic object except target. Therefore, be sure to provide a minimum distance as below chart indicates.
When the height between the Proximity sensor and surrounding metals is same.
接近传感器与周围金属高度相等时
When the height between the Proximity sensor and surrounding metals is different.
特点Features
内置浪涌保护，电源反接保护和过流保护电路
IBuilt-in surge protection, reverse polarity protection, Overcurrent Protection circuit
寿命长，高可靠性，操作简单，经济实惠
Long life cycle and high reliability
红色LED状态指示灯，易于识别运行状态
Red LED status indication
IP67防护等级(IEC规格)
Protection structure IP67(IEC standard)
可以代替微动开关或限位开关广泛使用
Replaceable for micro switches and limit switches
| 型号名Model | ITY-□-□LA | ITY-□-□NA/PA/NB/PB | ITY-□-□KA/KB |
| 应差距离 Hysteresis | 检测距离的10%以下 Max10% Of sensing distance | ||
| 电源电源(使用电压范围)Power supply (Operating voltage) | 12-24VDC (10-30VDC) | 12-24VDC (10-30VDC) | 100-240VAC(86-264VAC) |
| 漏电流Leakage current | 0.6mA以下Max.0.6mA | 10mA以下Max.10mA | 10V以下Max.10V |
| 残留电压Residual voltage | 1.0V以下Max.1.0V | 1.0V以下Max.1.0V | 3.5V以下Max.3.5V |
| 温度的影响Affection by temp. | 在-25~+70℃温度范围内+20℃时的检测距离的 ± 10%以内 Max. ± 10% for sensing distance at ambient temperature 20℃ | ||
| 控制输出Control output | 2~200mA | ||
| 绝缘阻抗Insulation resistance | 50MΩ以上(500VDC为基准)Min.50MΩ(at 500VDC megger) | ||
| 耐电压Dielectric strength | 1500VAC50/60Hz 1分钟1500VAC50/60Hz for 1 minute | ||
| 耐振动Vibration | 10~55Hz(周期1分钟)振幅1mmX，Y，Z各方向2小时1mm amplitude at frequency of 10 to 55Hz(for 1 min)in each of X,Y,Z directions for 2 hours | ||
| 耐冲击Shock | 500m/s2 (50G)X, Y,Z各方向3次 500m/s2 (approx.50G)X, Y, Z directions for 3 times | ||
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) | ||
| 使用周围温度Ambient temperature | -25~+70℃(未结冰状态Noicing) | ||
| 储存温度Storage temperature | -30~+80℃(未结冰状态Noicing) | ||
| 使用周围湿度Ambient humidity | 35~95%RH(未结露状态No condensation) | ||
| 保护电路Protection circuit | 浪涌保护电路，过载&短路保护电路，过电流保护电路Surge protection circuit, Reverse polarity protection circuit, Overcurrent protection circuit | ||
| 材质Material | 外壳：耐热ABS，一般线缆(深灰色)：聚氯乙烯(PVC)，Case/Nut: Heat-resistantABS, Standard cable(Gray): Polyvinyl chloride (PVC) | ||
| 认证/防护等级Approval/Protection | CE\ROHS\ISO9001 IP67(IEC规格 Standard) | ||
(1)开关动作的应答频率为平均值。测定条件使用标准检测物，检测物的间距为标准检测物的2倍，设定距离为检测距离的1/2
(1)The response frequency is the average value.the standard sensing target is used and the width is set as 2 times of the standard sensing target,1/2 of the sensingdistance for the distance.
(1)The response frequency is the average value.the standard sensing target is used and the width is set as 2 times of the standard sensing target,1/2 of the sensingdistance for the distance.
外形尺寸 Dimensions
ITF48-15
规格 SpecificationS
| 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) |
| ITF36-07LA | 7mm | 50×50×1mm(铁 Iron) | 0~5.5mm | 300Hz |
| ITF42-10LA | 10mm | 55×55×1mm(铁Iron) | 0~7.5mm | 200Hz |
| ITF48-15LA | 15mm | 60 ×60×1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF55-20LA | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 100Hz |
| ITF36-07NA | 7mm | 50 ×50× 1mm(铁Iron) | 0~5.5mm | 300Hz |
| ITF36-07PA | 7mm | 50× 50× 1mm(铁Iron) | 0~5.5mm | 300Hz |
| ITF36-07NB | 7mm | 50 ×50× 1mm(铁Iron) | 0~5.5mm | 300Hz |
| ITF36-07PB | 7mm | 50 ×50×1mm(铁Iron) | 0~5.5mm | 300Hz |
| ITF42-10NA | 10mm | 55 ×55 × 1mm(铁Iron) | 0~7.5mm | 200Hz |
| ITF42-10PA | 10mm | 55× 55× 1mm(铁Iron) | 0~7.5mm | 200Hz |
| ITF42-10NB | 10mm | 55× 55× 1mm(铁Iron) | 0~7.5mm | 200Hz |
| ITF42-10PB | 10mm | 55× 55× 1mm(铁Iron) | 0~7.5mm | 200Hz |
| ITF48-15NA | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 100Hz |
| 可选型号Optional model | 检测距离Sensing distance | 标准检测物Standard sensing target | 设定距离Setting distance | 应答频率(1)Response frequency(1) |
| ITF48-15PA | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF48-15NB | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF48-15PB | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 100Hz |
| ITF55-20NA | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
| ITF55-20PA | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
| ITF55-20NB | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
| ITF55-20PB | 20mm | 80 ×80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
| ITF42-10KA | 10mm | 55× 55× 1mm(铁Iron) | 0~7.5mm | 20Hz |
| ITF42-10KB | 10mm | 55 ×55×1mm(铁Iron) | 0~7.5mm | 20Hz |
| ITF48-15KA | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 20Hz |
| ITF48-15KB | 15mm | 60 × 60 × 1mm(铁Iron) | 0~12.5mm | 20Hz |
| ITF55-20KA | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
| ITF55-20KB | 20mm | 80 × 80 × 1mm(铁Iron) | 0~15.5mm | 20Hz |
输出电路 Control Output Diagram
直流2线式 DC2-wire type
交流2线式 AC 2-wire type
连接 Connections
直流2线式 DC 2-wire type
负载可以连接 任意一根线 The load can be connected to either wire.
交流2线式 AC 2-wire type
交流2线式 AC 2-wire type
负载可以连接 任意一根线 The loadcan be connected to either wire.
直流3线式 DC3-wire type
当几个接近传感器安装在一起，会发生相互干扰引起传感器故障，一般两个传感器之间的间隔的距离如图
When several proximity sensors are mounted close to one another a malfunction of the sensor may be caused due to mutual interference. Therefore, be sure to provide a minimun distance between the two sensors as below chart indicates.
正确使用 Proper usage
相互干扰Mutual-interferece
直流3线式 DC 3-wire type
PA12,可选择NPN/PNP There isNPN/PNPselection switch in PA-12.
| 型号名Mode项目Item | ITF36-07 | ITF42-10 | ITF48-15 | ITF55-20 |
| A | 30 | 60 | 120 | 120 |
| B | 40 | 50 | 70 | 70 |
| C | 5 | 5 | 5 | 5 |
| φd | 15 | 30 | 60 | 60 |
| e | 25 | 30 | 45 | 45 |
| m | 20 | 25 | 35 | 35 |
应用实例 Flat Type Proximity Sensor
| 检测灌装品的不良品 | 检测螺丝的高度 |
  |  |
| 定位控制 | 停止位控制 |
 |  |
| 检测物体的位置 | 检测物体是否变形 |
 Proximity sensor |  |
| 检测螺丝 | |
 |  |
| 试验方法 | ||||||
| 等级 | 防护等级 | |||||
| 4 |  | 不受任何方向的 溅水影响 | 所有方向洒水10分钟  | |||
| 5 |  | 不受任何方向的 喷射水影响 | 所有方向喷射水3分钟  | |||
| 6 |  | 不受任何方向的 强力喷射水影响 | 所有方向强力喷射水3分钟  | |||
| 7 |  | 规定的时间和压 力内浸入水中无 影响 | 自然状态在水平面下1m处放置30分钟 | |||
| 8 | 在水中使用不受 影响 |  自然状态在水平面下10m内持续放置 | ||||
 |  | |||||
| 关于防止固定侵入防护等级 | 试验方法 | |||||
| 等级 防护等级 | 防止灰尘进入 | |||||
| 6 防尘型 | ||||||
防护等级Protection Grade
PLC放大板/隔離板PLCAmplifier
PLC放大板（英語：PLCAmplifier)是用于PLC与負載之間的隔離、放大電流等功能的中繼板，所以也称作IO中繼板。其作用是提高PLC的带载能力、保護PLC不受到过压、过载、負载短路等故障，而导致PLC主机損坛。
PLC Amplifier (PLC: Amplifier) is a relay board used for functions such as isolation and amplification of current between PLC and load, so it is also called IO relay board. Its role is to improve the carrying capacity of PLC, PLC protection against over-voltage, overload, load short-circuit and other failures, resulting in damage to the PLC host.
规格 Specifications
| 產品型號 | 基本参數 | 產品型號 | 基本参數 |
| 4路（4 ways series) | 12路(12ways series) | ||
| 4路NPN輸入PNP輸出 | 負入正出（低入高出） | 12路NPN輸入PNP輸出 | 負入正出（低入高出） |
| 4路NPN輸入NPN輸出 | 負入負出（低入低出） | 12路NPN輸入NPN輸出 | 負入負出（低入低出） |
| 4路通用型輸入PNP輸出 | 通用型入正出（通用型入高出） | 12路通用型輸入PNP輸出 | 通用型入正出（通用型入高出） |
| 8路(8 ways series) | 16路(8 ways series) | ||
| 8路NPN輸入PNP輸出 | 負入正出（低入高出） | 16路NPN輸入PNP輸出 | 負入正出（低入高出） |
| 8路NPN輸入NPN輸出 | 負入負出（低入低出） | 16路NPN輸入NPN輸出 | 負入負出（低入低出） |
| 8路通用型輸入PNP輸出 | 通用型入正出（通用型入高出） | 16路通用型輸入PNP輸出 | 通用型入正出（通用型入高出） |
产品特点 Products Feature:
1、使用先进的双CPU单片机智能控制技术，具有高可靠性、低故障率的特点：
应用范围Application range
应用各种负载：空调、电钻、日光灯、气体灯等家电设备，通信设备、保温空调、冷藏设备、测量仪器、通信设备、白炽灯、冰箱、空调、电脑、打印机、气泵、水泵、电磁炉、微波炉马达、电动工具、车辆求援、抢险救灾、数码摄像机、数码相机、电池充电及GPS卫星导航等。
Apply to variety of load: household appliance, like air condition、electric drill、fluorescent lamp、gas lamp,etc.Communications equipments、refrigerated storage equipment、measurement instrument、filament lamp、refrigerator、laptop、printer、air pump、water pump、electromagnetic oven、microwave oven、juicer、electric drill、motor、electric tool、vehicle rescue、disaster relief、digital video camera、digital camera、battery charger and GPS satellite navigation, etc.
| 型号名Model | XM-DZ纯正弦波逆变器 |
| 输入电压 Input voltagel | DC12V/DC24V/DC48V |
| 输出电压 Output voltagel | 110VAC or 110VAC 120VAC ± 5% 220VAC or230VAC 240VAC ± 5% |
| 输出频率Output Frequency | 50Hz ± 0.5Hz or 60Hz ± 0.5Hz |
| 输出波形Output wave | 纯正弦波 Pure sine wave |
| USB | 5V 1000MA |
| 最大效率Max.working effciency | 94.8% |
| 输入电压范围Input voltage range | 9.55-15.5V/19.8-30.27V/40.2-60.4V |
| 质保Warranty | 二年 TWO Years |
| 显示Display | LED 高清显示屏LED high-definition digital display |
| 耐冲击Shock | 500m/s2 (50G)X, Y,Z 各方向3次 500m/s2 (approx.50G)X, Y, Z directions for 3 times |
| 显示灯Indicator | 动作指示灯(红色LED)Operation indicator(red LED) |
| 切换时间Transfer time | 1 |
| 逆变优先Battery priority | 1 |
| 启动Starting | 1 |
| 保护功能Protection | 1 |
| 认证Approval | CE\ROHS\ISO9001 |
规格 Specifications
外形图 Specifications
| 可选型号Optional mode | 输出功率Out power | 峰值功率Peak power | 欠压报警 | 欠压恢复 | 压O | 高压恢复 | 产品尺寸Size(WH'D) | |||||||||||
| 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | ||||
| XM-DZ-300 | 300W | 600W | 10.5V | 21V | 42V | 9.5V | 20V | 40V | 13V | 24V | 48V | 15.5V | 31V | 61V | 14.8V | 29.5V | 59V | 187×110×52mm |
| XM-DZ-500 | 500W | 1000W | 251×151×85mm | |||||||||||||||
| XM-DZ-800 | 800W | 1600W | 332×167×92mm | |||||||||||||||
| XM-DZ-1000 | 1000W | 2000W | 332×167×92mm | |||||||||||||||
| XM-DZ-1500 | 1500W | 3000W | 390×167×92mm | |||||||||||||||
| XM-DZ-2000 | 2000W | 4000W | 415 × 167× 92mm | |||||||||||||||
| XM-DZ-2500 | 2500W | 5000W | ±0.5V | ±0.5V | ±0.5V | ±0.5V | ± | ± | ± | ± | ± | ± | ±0.5V | ±1V | ±0.5V | ±0.5V | ±1V | 415×167×92mm |
| XM-DZ-3000 | 3000W | 6000W | 0.5V | 0.5V | 0.5V | 1V | 0.5V | 405×200×154mm | ||||||||||
| XM-DZ-4000 | 4000W | 8000W | 467×200×154mm | |||||||||||||||
| XM-DZ-5000 | 5000W | 10000W | 447×200×154mm | |||||||||||||||
| XM-DZ-6000 | 6000W | 12000W | 580×200× 154mm | |||||||||||||||
| XM-DZ-8000 | 8000W | 16000W | 625×240×190mm | |||||||||||||||
XM-DZ-300<br>XM-DZ-800/XM-DZ-1000
XM-DZ-500<br>XM-DZ-1500
外形图 Specifications
纯正市电充电系列
| 型号名Model | XM-DB纯正市电充电逆变器 |
| 输入电压 Input voltagel | DC12V/DC24V/DC48V |
| 输出电压 Output voltagel | 110VAC or 110VAC 120VAC ± 5% 220VAC or230VAC 240VAC ± 5% |
| 输出频率Output Frequency | 50Hz ± 0.5Hz or 60Hz ± 0.5Hz |
| 输出波形Output wave | 纯正弦波 Pure sine wave |
| USB | 5V 1000MA |
| 最大效率Max.working effciency | 94.8% |
| 输入电压范围Input voltage range | 9.55-15.5V/19.8-30.27V/40.2-60.4V |
| 质保Warranty | 二年 TWO Years |
| 显示Display | LED 高清显示屏LED high-definition digital display |
| 耐冲击Shock | 500m/s² (50G)X, Y,Z各方向3次 500m/s² (approx.50G)X, Y, Z directions for 3 times |
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) |
| 切换时间Transfer time | 1 |
| 逆变优先Battery priority | 1 |
| 启动Starting | 1 |
| 保护功能Protection | |
| 认证Approval | CE\ROHS\ISO9001 |
规格 Specifications
外形图 Specifications
外形图 Specifications
| 可选型号Optional model | 输出功率Out pov | 峰值功率 | 欠压报警 | 欠压保护 欠压 高 高 恢复LOW O WT Over | ||||||||||||||
| 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | ||||
| XM-DB-500 | 500W | 1000W | 10.5V±0.5V | 21V±0.5V | 42V±0.5V | 9.5V±0.5V | 20V±0.5V | 40V±1V | 13V±0.5V | 24V | 48V | 15.5V±0.5V | 31V±0.5V | 61V±1V | 14.8V±0.5V | 29.5V±0.5V | 59V±1V | 251×151×85mm |
| XM-DB-1000 | 1000W | 2000W | 332×167×92mm | |||||||||||||||
| XM-DB-1500 | 1500W | 3000W | ±0.5V | ±1V | 390×167×92mm | |||||||||||||
| XM-DB-2000 | 2000W | 4000W | 415×167×92mm | |||||||||||||||
| XM-DB-2500 | 2500W | 5000W | 415×167×92mm | |||||||||||||||
| XM-DB-3000 | 3000W | 6000W | 405×200×154mm | |||||||||||||||
XM-DB-500
XM-DB-1000
修正弦波系列
| 型号名Model | XM-DX修正正弦波逆变器 |
| 输入电压 Input voltagel | 11-16VDC/26.4VDC |
| 输出电压Output voltagel | 1 |
| 输出频率Output Frequency | 1 |
| 输出波形Output wave | 修正正弦波 Modified sine wave |
| USB | 5.0 ± 0.25VDC 2.0A |
| 最大效率Max.working effciency | ≥92% |
| 输入电压范围Input voltage range | 1 |
| 质保Warranty | 二年 TWO Years |
| 显示Display | LED 高清显示屏LED high-definition digital display |
| 耐冲击Shock | 500m/s² (50G)X, Y,Z 各方向3次 500m/s² (approx.50G)X, Y, Z directions for 3 times |
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) |
| 切换时间Transfer time | ≤8MS |
| 逆变优先Battery priority | 默认逆变优先/可选Optional/Default Battery Priority |
| 启动Starting | 双极软启动Bipolar soft Start |
| 保护功能Protection | 输出短路保护 AC short circuit protection过温度保护 Operating temperature range |
| 认证Approval | CE\ROHS\ISO9001 |
规格 Specifications
| 可选型号Optional model | 输出功率Out power | 峰值功率Peak power | 输入电压Input voltage | 输出电压Output voltage | 无负载输入电流-load curren | 交流电压频率No-load curren | 产品尺寸Size(WH"D) |
| XM-DX-100 | 100W | 200W | 50 ± 1Hz | 85×65×38mm | |||
| XM-DX-150 | 150W | 300W | 85×65×38mm | ||||
| XM-DX-200 | 200W | 400W | 85×65×38mm | ||||
| XM-DX-300 | 300W | 600W | 12V/24V | 110V/220V | ≤0.1A≤0.3A | 158×102×54mm | |
| XM-DX-500 | 500W | 1000W | 158×102×54mm | ||||
| XM-DX-1000 | 1000W | 2000W | 205×102×54mm | ||||
| XM-DX-1500 | 1500W | 3000W | 225×205×80mm | ||||
| XM-DX-2000 | 2000W | 4000W | 340×205× 80mm | ||||
| XM-DX-3000 | 3000W | 6000W | 420×205×80mm |
规格 Specifications（带市电充电Mains Charger）
| 可选型号Optional model | 输出功率Out power | 峰值功率Peak power | 输入电压Input voltage | 输出电压Output voltage | 无负载输入电流No-load curren | 交流电压频率No-load curren | 产品尺寸Size(WH*D) |
| XM-DX-1000(带市电充电) | 1000W | 2000W | 12V/24V | 110V/220V | ≤0.1A≤0.3A | 50 ± 1Hz | 205×102×54mm |
| XM-DX-1500(带市电充电) | 1500W | 3000W | 225×205×80mm | ||||
| XM-DX-2000(带市电充电) | 2000W | 4000W | 340×205×80mm | ||||
| XM-DX-3000(带市电充电) | 3000W | 6000W | 420× 205 ×80mm |
XM-DX-100/XM-DX-150/XM-DX-200
XM-DX-300/XM-DX-500<br>XM-DX-1500
XM-DX-1000
XM-DX-2000
XM-DX-3000
纯正LIPS系列
| 型号名Model | XM-ZB纯正UPS逆变器 |
| 输入电压 Input voltagel | DC12V/DC24V/DC48V |
| 输出电压 Output voltagel | 110VAC or 110VAC 120VAC ± 5% 220VAC or230VAC 240VAC ± 5% |
| 输出频率Output Frequency | 50Hz ± 0.5Hz or 60Hz ± 0.5Hz |
| 输出波形Output wave | 纯正弦波 Pure sine wave |
| USB | 5V 1000MA |
| 最大效率Max.working effciency | 94.8% |
| 输入电压范围Input voltage range | 9.55-15.5V/19.8-30.27V/40.2-60.4V |
| 质保Warranty | 二年 TWO Years |
| 显示Display | LED 高清显示屏LED high-definition digital display |
| 耐冲击Shock | 500m/s² (50G)X, Y,Z 各方向3次 500m/s² (approx.50G)X, Y, Z directions for 3 times |
| 显示灯Indicator | 动作指示灯(红色LED) Operation indicator(red LED) |
| 切换时间Transfer time | 1 |
| 逆变优先Battery priority | 1 |
| 启动Starting | 1 |
| 保护功能Protection | 一 |
| 认证Approval | CE\ROHS\ISO9001 |
规格 Specifications
| 可选型号 Optional mode | 输出功率 Out power | 峰值功率 | 欠 12V | 欠压 | 高 | |||||||||||||
| XM-ZB-500W | 500W | 1000W | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 12V | 24V | 48V | 251×151×85mm | |
| XM-ZB-800W | 800W | 1600W | 332×167×92mm | |||||||||||||||
| XM-ZB-1000W | 1000W | 2000W | 21V | 42V | 9.5V | 40V | 13V | 24V | 48V | 15.5V | 61V | 14.8V | 29.5V | 59V | 332×167×92mm | |||
| XM-ZB-1500W | 1500W | 3000W | 10.5V | ± | ± | 20V | ± | 31V | ± | 390×167×92mm | ||||||||
| XM-ZB-2000W | 2000W | 4000W | ± 0.5V | 0.5V | 0.5V | ± 0.5V | ± 0.5V | ± 1V | ± 0.5V | ± 1V | ± 0.5V | ± 0.5V | ± 1V | ± 0.5V | ± 0.5V | 1V | 415×167×92mm | |
| XM-ZB-2500W | 2500W | 5000W | 0.5V | 415×167×92mm | ||||||||||||||
| XM-ZB-3000W | 3000W | 6000W | 405 × 200 × 154mm | |||||||||||||||
外形图 Specifications
XM-ZB-500<br>XM-ZB-800
手机官网
企业微信号
注：本目录所提供的数据仅供参考，以实际产品为准，或咨询客服。参数内容如有改动不另行通知。感谢您对西盟的支持！ All figures on this for reference only and subjected to actual products, We will not keep you informed for any change,which will be explaint by our company.
更多产品信息，及优惠活动请关注西盟手机官网及企业微信号 More product informations and discount,please visit the website and wechat of Ximeng.
绿色能源法则 缔造完美品质 The rule of green energy creates perfect quality
