该页无缩略图
型-上下是铝板内有隔离片(根据用户要求放隔条)
II -type Separate type of support board
Ill -type The upper one and the lower one are made of aluminium with spacer inside
TL225钢制拖链安装尺寸图
★订货举例
拖链型号TL225，支撑板Ⅲ型，弯曲半径R=600，
支撑板宽度Bi=400，拖链长度L=12000
拖链TL225III-R600x400x12000
I型-支撑板整体型(根据用户要求开孔)
II型-支撑板上下分开型(根据用户要求开孔)
Ⅲ型-上下是铝板内有隔离片(根据用户要求放隔条)
★Example for an order
Drag chain model number TL225, supporting board Il type, bend radius R=600, supporting board width Biz =400 length L=12000
Drag chain TL225III -R600 x 400 x 12000
I -type Integral type of support board
II -type Separate type of support board
Ill-type The upper one and the lower one are made of aluminium with spacer inside
TL250钢制拖链安装尺寸图
★订货举例
拖链型号TL250，支撑板Ⅲ型，弯曲半径R=600,支撑板宽度Bi=400，拖链长度L=12000拖链TL250III-R600x400x12000I型-支撑板整体型(根据用户要求开孔)II型-支撑板上下分开型(根据用户要求开孔)Ⅲ型-上下是铝板内有隔离片(根据用户要求放隔条)
★Example for an order
Drag chain model number TL250, supporting board Il type, bend radius R=600, supporting board width Biz =400 length L=12000
Drag chain TL250III -R600 x 400 x 12000
I -type Integral type of support board
II -type Separate type of support board
Ill -type The upper one and the lower one are made of aluminium with spacer inside
◆TLG系列钢制拖链概况
TLG型钢制拖链可承载数量多，重量大的电缆及油管，自由悬置(允许不用支承轮)长度大，支撑板可依顾客需要制作，适用于工作母机，移动机械等。其弯曲半径为75-600mm，链板高度为50-150mm，可任意选用。
TLG型钢制拖链其使用行程最大为32米。适用于所有传动方式。可随意加长和缩短。此外，可通过改变销轴获得改变弯曲半径。
拖链的支撑板宽度为50mm至600mm，孔与孔之间的间隔量为5mm。
链板的高度，也就是支撑板的高度，是由电缆最大直径决定的，机床最大限度运转时，如拖链的宽度超过300mm，拖链的长度超过4m时出于稳定性原因，应考虑选择加大一号规格的拖链。
弯曲半径要根据电缆的最大直径选择并应达到电缆直径的10倍。弯曲半径可根据所给表格选择50-600mm,行程小的可相应选择较小的半径。
拖链的长=1/2行程+4个弯曲半径，这只适用于当固定联结是在行程的中点时。拖链的固定可根据机床的位置情况选择。固定角钢可放在外周或内周在拖链内或外部。一般情况联结部分在拖链内，而向外周。
订货举例：行程11.2m，弯曲半径300mm，3电缆直径48，3电缆直径28，2软管直径36
TLG系列钢制拖链主要参数及支撑尺寸
| 型号Type | 弯曲半径R(mm)Bending radius | 节距pitch | a | C | d | e | f | g | h | k | 允许不用支撑轮时When non-supportwheel is allowed | |
| 长度mlength | 负载kg/mload | |||||||||||
| TLG-A75TLG-B75 | 100/150/200/250/300 | 75 | 31 | 50 | 8 | 4 | 30 | 12 | 9 | 15 | 3/4 | 30/30 |
| TLG-A100TLG-B100 | 150/200/250/300/400 | 100 | 49 | 75 | 10 | 4 | 50 | 17 | 11 | 21 | 4/8 | 40/40 |
| TLG-A125TLG-B125 | 200/250/300/400/500 | 125 | 68 | 100 | 14 | 4 | 70 | 22 | 13 | 28 | 6/12 | 50/50 |
| TLG-A175TLG-B175 | 250/300/400/500/600 | 175 | 118 | 150 | 14 | 8 | 115 | 26 | 13 | 32 | 10/15 | 10/30 |
| Specifications for ordering:Travel1.2m,Bending radius300mm,3Cable diameter48,3Cable diameter28,2Hoses diameter36 | |||||
| TLG-A75/ | 300× | 6875/ | 350- | D/E | "S" |
| 型号 | 半径 | 长度 | 支撑板宽度 | 固定方式 | 安装形式 |
| Type | Radius | Length | Width of support board | Mode of fixing | Mode of installation |
TLG型的多种不同支撑板
TLG铝合金型拖链与一般的拖链不同，它可通过固定的铝型材满足不同要求的需要，支撑板宽或达1200mm,在最高速度和行程速度下，拖链的内部分隔无懈可击，并保证使电缆达到最佳保护。
TLG type supporting boards in various specifications
The TLG type aluminium alloy drag chains are different from theordinary ones. They can made by using fixed aluminium shape materialsto meet the needs of the users.The width of the supporting board can be1200mm. When operating under high operating speed and high travelspeed, the drag chains can be separated from one another so as toensure the cables being protected in a very safe conditions.
TLG-|铝合金型是解决较大钢链的唯一的解决办法。支撑板可根据使用者的要求生产。牢固的结构，使支撑板宽度可达到1200mm。
TLG- I aluminium alloy type is the only solution to the larger size chains The supporting boards can be made according to the requirments of the users. Thanksto the strong construction, the width of the supporting board can be 1200mm.
TLG-Ⅱ型带塑料隔条，可随意移动调节位置，进行多种分隔，如果电缆规格多，可选用此经济的装置。
TLG-II plastic spacing straps can moved and adjusted in position freely.If cables in many different specifications, you may select this economic device
◆TLG75钢制拖链安装尺寸图
拖链型号TLGA75，支撑板型，弯曲半径R=150,
支撑板宽度Bi=200，拖链长度L=6500
拖链TLGA75 III -R150 × 200 × 6500
Ⅱ型-支撑板上下分开型(根据用户要求开孔)
ⅢⅢ型-上下是铝板内有隔离片(根据用户要求放隔条)
★Example for an order
Drag chain model number TLGA75, supporting
board III type, bend radius
R=150, supporting board width Bi=200 length
L=6500
Drag chain TLGA75III -R150 x 200X 6500
II -type Separate type of support board
II -type The upper one and the lower one are
made of aluminium with spacer inside (we can follow the requirement of customer
to manufacture)
标准联结Standard connection标准联结Standard connection
◆TLG100钢制拖链安装尺寸图
拖链型号TLGA100，支撑板型，弯曲半径R=250 支撑板宽度Bi=200,拖链长度L=7000
拖链TLGA100II -R250 x 200 x 7000
Ⅱ型-支撑板上下分开型(根据用户要求开孔)
IⅢ型-上下是铝板内有隔离片(根据用户要求放隔条) ★Example for an order
Drag chain model number TLGA100, supporting board I type,bend radius
R=250, supporting board width Bi=200 length L=7000
Drag chain TLGA100 III -R250 x 200 x 7000. II -type Separate type of support board
Ill-type The upper one and the lower one are made of aluminium with spacer inside
(we can follow the requirement of customer to manufacture)
标准联结Standard connection
TLG125钢制拖链安装尺寸图
★订货举例 贝十例
拖链型号TLGA125，支撑板Ⅲ型,弯曲半径R==300,
支撑板宽度Bi=200,拖链长度L=7500
拖链TLGA125 III -R300 x 200 x 7500
Ⅱ型-支撑板上下分开型(根据用户要求开孔)
IⅢ型-上下是铝板内有隔离片(根据用户要求放隔条)
★Example for an order
Drag chain model number TLGA125, supporting
board III type, bend radius
R=300, supporting board width Bi=200 length L=7500
Drag chain TLGA125 I -R300 x 200 x 7500
II -type Separate type of support board
Ill-type The upper one and the lower one are
made of aluminium with spacer inside
(we can follow the requirement of customer to
manufacture)
标准联结Standard connection
联结方式A 联结方式BManner of connection A Manner of connection B
◆TLG175钢制拖链安装尺寸图
★订货举例
拖链型号TLGA175，支撑板Ⅲ型,弯曲半径R=500，
支撑板宽度Bi=200，拖链长度L=9000
拖链TLGA175II - -R500 x 200 x 9000
Ⅱ型-支撑板上下分开型(根据用户要求开孔)
IⅢ型-上下是铝板内有隔离片(根据用户要求放隔条)
★Example for an order
Drag chain model number TLGA175, supporting
board III type, bend radius
R=500, supporting board width Bi=200 length L=9000 Drag chain TLGA175 III -R500 x 200 x 9000
Il -type Separate type of support board .
Ill-type The upper one and the lower one are made of aluminium with spacer inside
(we can follow the requirement of customer to
manufacture)
联结方式A 联结方式BManner of connection A Manner of connection B
◆TL拖链长度的确定
拖链长度的计算取决于 / { L A } { 2 } 中心点到弯曲半径的距离，这个值(b)会随着拖链节距的变化而变化，适用于尼龙拖链和钢铝拖链。
拖链长度确定公式 L =拖链长度
拖链长度的计算取决于 / { L A } { 2 } 中心点到弯曲半径的距离，DPJ表示固定端偏离中心点的距离，这个值(b)会随着拖链节距的变化而变化，适用于尼龙拖链和钢铝拖链。
DPJ=固定端偏离行程中心的距离
b =曲线的长度 { \left( { \begin{array} { l l } { π x R } \end{array} } \right) } + { \left( { \begin{array} { l l } { 2 x \mathsf { P } } \end{array} } \right) }
P =节距
{ \sf L } { \sf I } = \left( { \sf H } / 2 x π \right) / 2 按装高度Hp=H+D1
拖链辅助产品——支撑轮
支撑轮单位
当拖链应用在行程上，且承载的重量超过拖链自我的支撑能力的时候，有必要使用支撑轮。决定使用支撑轮的数量，注意下面的情况。
拖链辅助产品——导向槽
特殊的导向槽使拖链能够应用于长距离的行程上，导向槽可使用镀锌钢的材料，根据要求也可以做成不锈钢的。
单一拖链的应用
导向槽由以下部分构成：
标准长度的侧导向槽
导向槽联结角钢
安装螺丝
底槽
滑行装置(尼龙轮/钢或
拖链辅助产品——导向槽
空的导向槽部分
导向槽的安装
检查导向槽与牵引臂之间的距离在运行过程中是否保持了一致。
支撑轮制作图
各拖链型号的自由跨度选定好的情况下，随着设备的特点在拖链需要延长使用长度时，为了防止拖链下垂而在下面安装支撑滚轮以延长使用长度并防止产品下垂。
When extended lengths are needed even if there arealready free span length per each type, the Fixed RollerSupport should be installed as the left picture to preventthem from being sagged.
双向移动拖架安装
Install the two-way moves support frame
轨道的安装
·确保地面无异物后，保持水平高度。
·轨道以中心为基准,左右侧都应保持设备的行程
距离多3M的富余长度。
·安装时需注意事项--上下左右应保持水平高度。
●The installation of the track
·After ensuring there is no foreign body, maintain the level of height
·Relative to the center, the support frame left and right side should keepmore 3 meters than equipment's travel distance
·Note that when you install matters- -should be maintained at levels In alldirections
TLB型并联钢制拖链
拖链与托架的安装指导
拖链的安装顺序：
①拖链以导向轨道中心为基准，左右各保留250mm的间隔进行安装。②固定端安装在轨道上段→安装拖链接头的固定端→用定位片连接拖链。托架的安装顺序：
①在拖链上端将一般托架用螺丝与弹簧连接。
②左右弯曲托架，在拖链上段用螺钉与弹簧将一般托架连接。
③托架连接后，拖链沿托架的弯曲线连接起来再固定住。
◆The installation guide of towline and support frame
•The installation sequence of drag chain:
1. Regard the guide track center as the benchmark, around the retention interval of
250mm for installation
2. The fixed end is arranged on the upper of the track→install the joint fixed end of towline→Connect the chains use the Positioning pieces
·The installation sequence of support frame
1. Connect the support frame by springs and screws in the towline upper part
2. Bending the support frame at left and right, connect the support frame by springs and screws in the towline upper part.
3. After the support frame' s connection, join the towline along the curve of support frame, then fixd it.
拖链的安装方法：
①沿着托架弯曲线连接起来的拖链的左右边连接到托架的中心位置。
②左右拖链与移动端连接后再安装在设备的移动端上。
③最后将胶管穿插到拖链中。
◆The installation sequence of drag chain:
1. Connect the drag chain' s left and right to the central position of support frame
2. After connected the left and right chain with mobile terminal then install it on the mobile terminal of equipment.
3. At the and, the rubber hose through to the drag chain
TLB带三条链板的并联拖链
因为各种型号拖链的支撑板最大宽度受限，在较宽拖链上可以装置一个或多个拖链链板。另外的原因是，可提高较窄的拖链的稳定性，此外也可通过第三条链板将套管与电缆隔开。
订货举例
拖链型号TL95，支撑板IⅢ型，弯曲半径R=250，支撑板宽度、拖链长度:TL95I-R250X300X325X13580
◆ DGT型导管防护套（全封闭美观型）
结构制作与用途
套板外径镀铬处理，和不锈钢及塑料，内有工程塑料增强尼龙66加纤维组合而成；套板不锈钢板抛光处理，内有工程塑料组合而成，结构合理，强度高、不变形、外形精美等优点。
安装方便，适用于各类机床机械电器、液压气动管线防护和装饰美主机整体造型。确保操作人员劳动安全，增强我国机床，机械设备在国际市场的竞争能力。
选型
注明规格与型号如下所示：
(1)如1#1200-A-Ⅱ或25x 45x1200- A-ⅡI
(2)如4#1800-AB-或52x102x1800-AB-选型请注意规格,型号,装配形式A、B、C、D。
Construction and Applications
It consists of an outer sleeve being chromium plated, stainless steel and plastics pieces and engineering plastic reenforced nylon fibre. The stainless steel bushing is polished. It has some engineering plastic items. It is featured by rational construction, high strength, non-deformation and has nice-looking appearance.
Easy installation. It is suitable for various of electrical of the machine tools, protection for hydraulic pneumatic pipelines and decoration of main machineries and provide the operating personnel with safe working conditions and better the competitiveness of machine tools and machineries in the international market.
Selections
Please give a clear indication of spesifications and model numbers as shown below:
(1) For instance, 1#1200-A- I or 25 x 45 x 1200-A- II
(2) For instance, 3#1800-AB-I or 52 x 102 x 1800-AB-I
For your selection,please note the specifications and model numbers and assembly modeA, B, C ,D.
| 型号 Type | 1# | 2# | 3# | 4# | 5# | 6# | 7# |
| 规格 Spec. | $2 5 \times 4 5$ | $3 8 \times 7 3$ | $4 5 \times 9 0$ | $5 2 \times 1 0 2$ | $6 0 \times 1 2 0$ | $6 0 \times 1 5 0$ | $7 2 \times 1 6 2$ |
| 外型 Appearance | $3 9 \times 6 2$ | $5 3 \times 9 1$ | $6 1 \times 1 0 8$ | $7 0 \times 1 2 2$ | $8 1 \times 1 4 4$ | $8 1 \times 1 8 4$ | $9 3 \times 1 8 6$ |
| 弯曲半径 Bending radius | 60 | 100 | 120 | 140 | 160 | 165 | 185 |
| 不支承长度 M Length for non-supporting | 1.5 | 2 | 2.2 | 2.5 | 2.7 | 2.9 | 3.0 |
| 负载重量 Load Weight | 3 | 4 | 5 | 8 | 10 | 14 | 20 |
| 参数 Parameters规格 Spec. | h | b | e | ${ \mathsf { d } } _ { \tau }$ | $^ { 1 , }$ | $\boldsymbol { \mathsf { I } } _ { 2 }$ |
| 1# | 39 | 62 | 22 | Φ6.5 | 30 | 15 |
| 2# | 53 | 91 | 50 | Φ6.5 | 30 | 15 |
| 3# | 61 | 108 | 62 | Φ6.5 | 35 | 15 |
| 4# | 70 | 122 | 65 | Φ8.5 | 40 | 20 |
| 5# | 81 | 144 | 70 | Φ8.5 | 40 | 20 |
| 6# | 81 | 184 | 80 | Φ8.5 | 40 | 20 |
| 7# | 93 | 186 | 100 | Φ8.5 | 45 | 20 |
| 参数 Parameters规格 Spec. | h | b | e | ${ \mathsf { d } } _ { \tau }$ | $\boldsymbol { \mathsf { I } } _ { \mathsf { \Omega } _ { 1 } }$ | $\boldsymbol { \mathsf { I } } _ { 2 }$ |
| 1# | 39 | 62 | 75 | Φ6.5 | 30 | 90 |
| 2# | 53 | 91 | 105 | Φ8.5 | 35 | 120 |
| 3# | 61 | 108 | 128 | Φ8.5 | 40 | 137 |
| 4# | 70 | 122 | 140 | Φ8.5 | 40 | 160 |
| 5# | 81 | 144 | 155 | Φ8.5 | 45 | 167 |
| 6# | 81 | 184 | 188 | Φ8.5 | 45 | 197 |
| 7# | 93 | 186 | 200 | Φ8.5 | 45 | 226 |
| 参数 Parameters规格 Spec. | h | b | eb | ${ \mathsf { d } } _ { \mathsf { r } }$ | $1 ,$ | eh | $\mathsf { h } _ { \mathsf { \Omega } _ { 1 } }$ |
| 1# | 35 | 60 | 18 | Φ6.5 | 30 | 55 | 80 |
| 2# | 50 | 85 | 45 | Φ6.5 | 35 | 70 | 95 |
| 3# | 114 | 103 | 52 | Φ8.5 | 42 | 87 | 102 |
| 4# | 65 | 114 | 60 | Φ8.5 | 40 | 90 | 115 |
| 5# | 73 | 132 | 68 | Φ8.5 | 42 | 103 | 123 |
| 6# | 73 | 163 | 83 | Φ8.5 | 44 | 103 | 123 |
| 7# | 85 | 175 | 95 | Φ8.5 | 45 | 110 | 135 |
| 参数 Parameters规格 Spec. | h | b | e | ${ \mathsf { d } } _ { \mathsf { \Omega } _ { 1 } }$ | $1 ,$ | $\boldsymbol { \mathsf { I } } _ { 2 }$ |
| 1# | 39 | 62 | 22 | Φ6.5 | 60 | 15 |
| 2# | 53 | 91 | 50 | Φ6.5 | 65 | 15 |
| 3# | 61 | 108 | 75 | Φ6.5 | 65 | 15 |
| 4# | 70 | 122 | 82 | Φ8.5 | 70 | 20 |
| 5# | 81 | 144 | 100 | Φ8.5 | 70 | 20 |
| 6# | 81 | 184 | 130 | Φ8.5 | 70 | 20 |
| 7# | 93 | 186 | 140 | Φ8.5 | 75 | 20 |
◆JR-2型矩形金属软管（全封闭强力型）
结构与用途
矩形金属软管采用全金属结构。该产品符合JB/GQ058285企业联合标准，适应于各类金属切屑机床及切割机床。防止高热铁屑对您供电、水、汽线路的损伤，保护劳动安全。
选型
1.注明规格与型号如下所示：
A×B×L-装配形式；L-软管长度，包括联接器装配，形式见软管装配形式图：1\~IX
2.特殊接头形式：a-c;
例：25×50×1200-1、25×50×1200-AB-
Construction and applications
The rectangle metalic hosed suitable for all types of metal cutting machine tools and slicing machines.Protect working personnel, electric circuits,water supplying piping systems and gas loops from damaging or injured.
The product is according to the standard JB/GQ58285.
Model selection
1. Give a clear indication of the specifications and model numbers as given below;
A X B X L - assembly type; L-hose length, including the assembly of the connectors, please see the hose assembly figrue for specifics: I\~ IX
2. Special connector types: a – c;
Example:25×50×1200-1、25×50×1200-AB-I
注：1.水平放置时下方应设置具有足够长度的拖板。
2.水平放置时允许选用超出表中规定的长度，但建议在适当的位置上设计滚动支承点，以防软管下弯。
Note: 1. When laid horizontally, a drag plate with enough length underneath should be provided.
2. When laid horizontally, a length that exceeds the length as given the table is allowed to use, but a rolling backing point is recommended to add at an appropriate position so as to avoid hose bending.
| A×B | C | D | E | F | G | H | 一 | L | J | K | N | P | S | X | T | Φ | R | 轴向拉力(kg)Axially pullingforce | 重量(kg/m)weight |
| 20 × 30 | 20 | 35 | 38 | 18 | 25 | 22 | 10 | 23 | 45 | 20 | 40 | 75 | 60 | 55 | 38 | 5.5 | 60 | 35 | 1.3 |
| 25×50 | 30 | 55 | 58 | 30 | 35 | 25 | 10 | 33 | 60 | 25 | 50 | 900 | 75 | 60 | 45 | 5.5 | 90 | 40 | 1.75 |
| 35× 60 | 40 | 65 | 69 | 40 | 45 | 25 | 10 | 44 | 70 | 30 | 50 | 100 | 80 | 70 | 52 | 5.5 | 100 | 50 | 2.1 |
| 38×73 | 43 | 78 | 82 | 50 | 55 | 35 | 10 | 47 | 75 | 35 | 50 | 105 | 85 | 82 | 62 | 6.5 | 110 | 60 | 2.36 |
| 40× 80 | 45 | 85 | 89 | 50 | 65 | 50 | 15 | 49 | 90 | 40 | 55 | 120 | 100 | 90 | 68 | 8.5 | 120 | 70 | 2.5 |
| 52×102 | 57 | 107 | 113 | 65 | 80 | 50 | 15 | 63 | 105 | 45 | 60 | 140 | 120 | 100 | 80 | 8.5 | 140 | 75 | 2.85 |
| 60 ×120 | 68 | 128 | 131 | 90 | 90 | 80 | 20 | 71 | 135 | 45 | 70 | 170 | 146 | 110 | 84 | 9 | 180 | 80 | 3.15 |
| 60 × 130 | 68 | 138 | 141 | 95 | 100 | 90 | 20 | 71 | 140 | 50 | 75 | 180 | 150 | 120 | 90 | 9 | 180 | 80 | 3.25 |
| 72×162 | 86 | 180 | 184 | 120 | 120 | 100 | 20 | 82 | 150 | 60 | 80 | 210 | 180 | 130 | 100 | 9 | 210 | 80 | 4.5 |
| 规格 Type | 20×30 | 25×50 | 35×60 | 38×73 | 40×80 | 52×102 | 60×120 | 60×130 | 72×162 |
| 允许承重(kg)Allowable weight | 3 | 6.5 | 10.5 | 11.5 | 12.5 | 16.5 | 20 | 22 | 24 |
| 允许长度(m)Allowable lenngth | 2 | 3 | 3 | 4 | 5 | 6 | 7 | 8 | 8 |
柔性风琴式防护罩 Flexible organ type protective cover
计算压缩长度的公式
AP =一个折的拉伸=(x·2)-8
SM=面料厚度
SS = 支撑片厚度
SF =法兰厚度
NP = 折数= / { P . A . } { A P } + 2
P.C. = (SM·8+SS)·NP+(SF· 2)
\*本数据表仅仅显示了我公司加工制作的一种高频焊接护罩类型，如需其他类型可与我公司工程技术人员联系。
P.A.=一个折的拉伸
P.C. = 压缩后长度
行程=拉伸后长度-压缩后长度
B = 外宽
a = 外高
x = 折高
例如：
数据：折叠高度=15 mm拉伸后长度=1000 mm
一个折的拉伸=(15×2)-8=22
折层数量= / { 1 0 0 0 } { 2 2 } + 2 = 4 8
压缩后长度=(0.25\*×8+1\*\*)×48+(2\*\*\*×2)
压缩后长度=3x48+4=148压缩后长度=148mm
\*使用代码“TEMAT015”的纤维面料
\*\*支撑片厚度为1mm
\*\*\*法兰厚度为2mm
Flexible organ type protective cover
柔性风琴式导轨防护罩设计参数
Design parameters for flexible accordion guide shieed
| 代号Code | 名称Description | 数据Data | 备注Remarks | 护罩结构材料Shield coustruction materials | |
| L | 拉伸后长度Ength after drawing | 面料plus material | 尼龙革或三防布Nylon cloth or protective cloth | ||
| L1 | 压缩后长度Length after compression | 支撑Support | PVC 片材（每格一片）Pvcsheet | ||
| L2 | 行程长度Travel length | 连接板Connecting plate | 树脂板、铁板Resin plate, iron plate | ||
| B | 防护罩总宽Total width of the shield | 滑轮Pulley | 铜或尼龙轴承Copper or nylon bearing | ||
| B{ | 导轨宽度Guide width | ||||
| B2 | 护罩内部宽度Interior width of the shield | 配套机床型号Machine tool model number | |||
| H | 护罩总高度Total height of the shield | 订货单位By pur chase order | |||
| H_{1 | 导轨高度Guide height of the guide | 联系人Contact person | |||
| H_2 | 护罩内部高度Interior width of the shield | 联系电话Contact tel | |||
| 注：1.用户订货时只要填明以上数据、选定材料，我公司代为设计制造。2. 如用户对护罩型式有特殊要求，我公司可与用户协商设计，满足要求。3. 每种防护罩填写一张。如样本不够，可复印填写。Note: 1. The enduser select the materials and data mentioned above when place an order and we will make the design and fabrication.2. If endusers have special reguirements, please lef us know and we can achieve for them.3. Pleasce fill in a form per type of shield. | |||||
计算高频焊接的护罩尺寸
Calculate the size of the shield for high-frequency welding
1. 根据工作条件选择折面材料;
2.每个折面都有坚固的PVC片支撑；
在设计阶段为了估算保护罩的体积，可参考下面的有关参数：
3. 特殊的滑片能避免在高速下产生噪音；
★标准折面的高度：15mm、20mm、30mm、35mm、40mm、45mm、50mm；
4.高频焊接；
★机械设备的导轨面和护罩之间的距离最小为5mm、最大为10mm;
5.固定用的支撑面。
★一个折面的展开尺寸等于折面高度的二倍减去10mm;
★一个压缩折面的厚度平均为4mm;
★防护罩压缩长度等于：
| 织物种类 | 厚度(mm) | 抗热性 | 防油性 | 抗溶解性 | 自熄性 |
| 涂敷聚乙烯的聚酯织物 | 0.20&0.36 | 最大 MAX90℃ | 很好 | 弱 | 是/否 |
| 涂敷聚氨酯的聚酯织物 | 0.22&0.35 | 最大 MAX110℃ | 很好 | 好 | 是/否 |
| Preotex 玻璃纤维织物 | 0.45 | 最大 MAX600℃ | 很好 | 好 | 是 |
| 涂敷聚氨酯的Nomex聚酰胺织物 | 0.25&0.38 | 最大 MAX160℃ | 很好 | 好 | 是 |
| 涂敷 Sylicon 硅橡胶的玻璃纤维织物 | 0.40 | 最大 MAX400℃ | 很好 | 很好 | 是 |
防尘折布参数
柔性风琴式防护罩 Flexible organ type protective cover
标准护罩使用在机床高立柱和大型机床长导轨上，结构合理，行走均匀，坚固耐用。
The standard shield has been used for the high column of the machine tools and for the long guide of heavy-duty machine tools, which is designed in rational construction, for uniform traveling and durable.
1. rasteniny lanyes.
3. 铜或尼绒滑片2. P01 Steel intermediate supports.
4. 尼绒轴和铜轴3. Brass or nvlon quide shoes
5. 拉筋和弹簧片(最高速度 120mt/分)4. Nylon supporting rollers.
6.侧面浮雕、铝铜材料的侧面支架，能安全地支撑护罩 5. Rods and snatch spring pantograph(max.speed 120 mt./min.).
7. 尼龙革 6. Bosses profile of chromed or galvanised steel,to secure the bellow to the support.
8. 防御聚亚安脂粘剂的油和乳状液 7. Plastic treated fabric.
9. 坚硬的聚氯乙烯薄片 8. Oil and emulsion resistant polyurethane adhesive.
10. 塑胶布 9. Rigid PVC sheet.
10. Plastic treated fabric.
风琴式防尘折布
Organ style dustproof folding cloth
| 代号 | 名称 | 数据 | 面料:用户自定 |
| B1 | 孔距 | 连接板:树脂板、钢板 | |
| $\mathsf { B } _ { 2 }$ | 宽度 | ||
| $\mathsf { B } _ { 3 }$ | 折高 | ||
| L | 伸长 |
多用型风琴式护罩主要部分的可行形状
Feasible shapes for the main parts of the multi-purpose organ style cover
以下是多用型护罩，它们可以应用在任何机器工具上，由于它们有能变化多端的形状和占用有限的空间供设计选用。
法兰紧固方法Flange tightening method
形式A:
用钢、铝、PVC板制造成与机床相对应的联结端板(机床体攻丝)形状和孔按用户图纸制造形式B:
用钢、铝、PVC板制造成与机床相对应的联结端板(机床体攻丝)形状和孔按用户图纸制造
形式C:
用钢、铝、PVC板制造成与机床相对应的联结端板(法兰攻丝）形状和孔按用户图纸制造
用钢、铝、PVC板制造成与机床相对应的联结端板(机床体攻丝)形状和孔按用户图纸制造
形式E
采用尼龙站扣快速连接的办法解决，用一个PVC支撑作为法兰
把尼龙粘扣条带贴到加强板上去。
建议干燥的工作环境采用此法。
形式F：用强力压的办法快速连接，用一个支撑当作法兰，采用强力压的办法连接上去。法兰是用薄钢板，铝或PVC制成，形状和孔按用户的图纸办理。建议在湿的工作环境中使用此法。
专用激光切割机焊接设备 Specialized laser cutting machine welding equipment
盔甲式机床防护罩
Armoured vertical shield for machine tools
盔甲式机床护罩
盔甲式不锈钢机床立护罩的每个折层能经受强烈的振动而不变形，同时应用在风箱上，以900℃高温而仍保持原有的状态，他们之间彼此支持，起着阻碍小碎片渗透的作用。
Armoured shield
Each fold of the armoured vertical shield can withstand strong shocks without any deformation. at the save time, It can stand a high tempera fure of 900℃ when used for bellows. They support each other and prevent debris from dropping inside.
特点
★按在护罩格上伸缩片
★小的空间必要条件
★可靠的保护层抵御大量的灰尘，砂末，铁屑耐高温
★伸缩片是铝合金和不锈钢板制成
★没有粘合关系
Features
Hinged mounted telescopic sheets.
★Small space requirement.
Reliable protection against large quantities of swarfs.
Individual telescopic sheets are easy to replace.
★No glued connections.
多用形式钢板不锈钢防护罩
Drawing for Sandard Shape Horigontal Steel Plate Shield
Design parameters
| 代号Code | 名称Description | 数据Data mm | 备注Remarks | 代号Code | 名称Description | 数据Data mm | 备注Remarks | ||
| Le | 拉伸后长度Length after drawing | $\mathsf { B } _ { \mathsf { s } }$ | 滚轮支承宽度Contact supporting width | ||||||
| Lz | 压缩后长度Length after compression | $\mathsf { B } _ { \mathsf { M } }$ | 滑块支承宽度Slider supporting width | ||||||
| Lt | 行程Travel range | ${ \mathfrak { a } } ^ { \circ } , { \mathfrak { \beta } } ^ { \circ }$ | 弓型倾角Bow-shaped dip | ||||||
| B | 导轨宽度Width of guide | v | 预计节数Estimated number of folds | ||||||
| Bc | 防护罩总宽Shield width | δ | 钢板厚度Thickness of steel plate | 用户预选Pre-selected by users | |||||
| H | 防护罩总高Total height of the shield | 安装孔Assembling hole | 用户自定By user | ||||||
| ${ \mathsf { H } } _ { \mathsf { \uparrow } }$ | 导轨侧面高度Side height of guide | 钢板材料Steel Plate mat`l | 1Gr13 | 2Cr13 | 用户自定By user | ||||
| ${ \sf H } _ { 2 }$ | 导轨上护罩高度Upper part height of shield | 支撑形式Supporting manner | 滚轮Pulley | 滑块Slidingpiece | 用户自定By user | ||||
| ${ \sf H } _ { 3 }$ | 安装位置高度lustallation position wldth | 配套机床型号Compount malline's type | |||||||
| ${ \mathsf { H } } _ { 4 }$ | 安装板高度Height of assembling plate | 委托单位Entrusting party | |||||||
| ${ \mathsf { H } } _ { 5 }$ | 滚轮高度Height of contact roller | 联系人Contact person | 电话Tel | ||||||
| 注：1.用户订货时只要填明上数据、选定材料，我公司代为设计、制造。2. 如用户对护罩型式有特殊要求，我公司可与用户协商设计，满足要求。3. 每种防护罩填写一张。如样本不够，可复印填写。Note: 1. The endusers select data and materials mentioned above and our company will talle care of the fabrication and dsign work.2. If endusers have special reguirements for shield type, please cet as know and we can achieve for them.3. One form for one type of shield. | |||||||||
钢板、不锈钢机床导轨防护罩
Steel Plate,Stainless Steel Machine Tool Slideway Protection-Shell
TSLP型提升机链板排屑机 TSLPlifting type chain plate debris removal unit
●TSLP型系列提升式链板排屑机，按结构尺寸分为（IⅡ Ⅲ)三种基本类型，Ⅰ型外形美观、紧凑适用于小型主机，Ⅱ Ⅲ型结构更加牢固可靠，适用于大中型主机及生产线上的远距离输送。
●TSLP型系列提升式链板排屑机，切屑输送速度选择范围大，工作效率高，有效排屑宽度多样化。可提供充足的选用范围，通过变化输送速度，排屑宽度可调整机器的排屑量，并且不受切屑种类的限制。对钢件、铸铁、铜、铝及非金属等，各种切屑均可适用。
链板采用高强度钢板或不锈钢板制作，抗拉强度高。
各部位的尺寸可根据切削机械的不同而设计。
TSLP type lifting chain plate debris removal unit can be divided into three categories(I, II and III)according to their structural dimensions.Category I is nice looking and compact in structure,which is suitalbe for the smallsized machine.Category II features strong and reliable structure,which is suitable for the large-and medium-sized machines and for long-distance transmission of the production line.
TSLP type lifting chain plate debris removal unit offers wide selection of tra -nsmission speed and working range and is of high working efficiency an -d has varible debris removal width. The amount of removed debris can be adjusted through varying the transmission speed regardless whatever materials are cut.It is suitable for the cutting operation of steel, cast iron, copper,aluminium and non-meta etc.
The chain plate is made of high strength steel plate or stainless steel plat -e,which are of high tensile strenth.
The dimensions of different parts can be designed according to different requirements of different cutting machines.
TSLP型提升机链板排屑机 TSLPlifting type chain plate debris removal unit
TSLP型提升式链板排屑机外形尺寸图 Overall Dimensions Drawing of TSLP lifting type chain plate debris removal unit
技术参数
Technical parameters
单位:mm
| 主要技术参数 Main Technical Parameters | 辅助技术参数 Auxiliary Technical Parameters | ||||||||||||||||
| 代号Code | L1 | B | B1 | B2 | H | α | H0 | H1 | H2 | H3 | L | L2 | L3 | 电机功率KWMotorpower | 运行速度米/分钟OperatingSpeedm/min | 输送物料名称Name ofmaterials tobetransmitted | 外壳颜色Color |
| 名称Name | 水平长度Horizontallength | 外壳宽度Shellwidth | 接屑宽度Width ofcollectingthe debris | 有效排屑宽度Effectivewidth ofdebrisremoval | 提升高度Liftinghigh | 提升角度Liftinghigh | 支腿高度Supportingleg high | 外壳高度Shellheight | 水平高度Horizontalheight | 入屑口高度Highlyof thedebrisinlet | 总长度Totallength | 接屑长度Debriscollectionlength | 支腿距离Supporting legdistance | ||||
| 尺寸Dimensions | |||||||||||||||||
| 水箱技术参数Water Tank Technical Parameters | ||||
| 名称Name | 水箱长度Length ofwater tank | 水箱宽度Width ofwater tank | 水箱高度Height ofwater tank | 冷却泵流量L/minFlowrate ofcooling pump |
| 尺寸Dimensions | ||||
注：
(1)电机功率根据有效排屑宽度B2、水平度L1、提升高度H确定。
(2)链板节距不同外壳高度H1最小高也不同; 节距31.75mm外壳最小高度H1100mm; 节距38.1mm外壳最小高度H1135mm; 节距50.8mm外壳最小高度H1180mm; 节距63.5mm外壳最小高度H1 230mm; 节距101.6mm外壳最小高度H1260mm;
(3)排屑机水箱的具体外形尺寸可根据用户要求制做成不同形状。
(4)可根据用户实际不同要求设计制造。
Note:
(1).Motor power can be determined by the effective width of debris removal B2,levelness L1 and lifting height H.
(2).If the pich of the chain plate is different,the heig -ht of different cases H1shall be different as well. Pitch31.75mm Min.height of the case H1 100mm; Pitch38.1mm Min.height of the case H1 135mm; Pitch50.08mm Min.height of the case H1 180mm; Pitch63.5mm Min.height of the case H1 230mm; Pitch101.6mm Min.height of the case H1 260mm; (3).The overall dimensions of the water tank can be made in different appearances according to the client requirement.
(4).It can be designed and fabricated according to the client requiements.
TSGP型提升刮板式排屑机 TSGP Lifting scraping plate type debris removal unit
●TSGP型系列提升刮板式排屑机，由于特定的结构，每片刮板均是独立工作的，将切屑沿机器底面刮送，当到达落屑区域时即与切屑分离。按结构尺寸分为（ⅠⅡⅢ)三种基本型，ⅠⅡ型外形美观紧凑，适用于中小型主机；Ⅲ型结构更加牢固可靠，适用于大中型主机及生产线上的远距离输送。
●TSGP型系列提升刮板式排屑机，输送速度选择范围大，工作效率高；有效排屑宽度多样化，可提供充足的选用范围；刮屑板的高度及分布间距可随机设计。
●刮板式排屑机主要用于断屑碎屑的输送。由于不受材质的限制，应用范围较广。
Due to specially designed structure,each of the scraping plate of TSGP typ -e lifting series scraping plate debris removal unit can work independentl -y.Debris thus produced can be transmitted along the baseplate of the m -achine.Debris will leave the scraping plate when reaching the debris col -lecting area.TGP type lifting scraping plate debris removal units are divi -ded into three categories(I, II and III )according to their structural dimen -sions.Category I is of nice looking and compactin stucture,which is suita -ble for the small-sized machine.Categories II and IIIare of stronger and more reliable structures,which are suitable for the large-and medium-siz -ed machines and for long-distance transmission of the production line.
TSGP type lifting scraping plate debris removal unit offers wideselection of transmission speed and working range and is of high working efficiency a -nd has variable debris removal width.It can provide you sufficient select -ion for use .The height and distribution distance can be designed accor -ding to each specific machine.
Scraping plate type debris removal unit is mainly used in the tansmission of fine debris or powder debris.Because of on limitation to the strutural m -aterial,it is widely used in different applications.
TSGP型提升刮板式排屑机
TSGP Lifting scraping plate type debris removal unit
TSGP型提升刮板式排屑机外形尺寸图
Overall Dimensions Drawing of TSGP Lifting scraping plate type debris removal unit
技术参数
Technical parameters
单位:mm
| 主要技术参数 Main Technical Parameters | 辅助技术参数 Auxiliary Technical Parameters | ||||||||||||||||
| 代号 code | L1 | B | B1 | B2 | H | α | 电机功率KWMotorpower | 运行速度米/分钟OperatingSpeedm/min | 输送物料名称Name ofmaterialsto betransmitted | 外壳颜色Shellcolor | |||||||
| 名称 Name | 水平长度Horizontallength | 外壳宽度Shellwidth | 接屑宽度Width ofcollectingthedebris | 有效排屑宽度Effectivewidth ofdebrisremoval | 提升高度Liftinghigh | 提升角度Liftingangle | 支腿高度Supportingleg high | 外壳高度Shellheight | 水平高度Horizontal | 入屑口高度Highlyof thedebrisinlet | 总长度Totallength | 接屑长度Debriscollectionlength | 支腿距离Supportinglegdistance | ||||
| 尺寸Dimensions | |||||||||||||||||
| 水箱技术参数 Water tank technical parameters | ||||
| 名称name | 水箱长度Length ofwater tank | 水箱宽度Width ofwater tank | 水箱高度Height ofwater tank | 冷却泵流量L/minFlowrate ofcoolingpump |
| 尺寸dimensions | ||||
注：
(1)电机功率根据有效排屑宽度B2、水平度L1、提升高度H确定。
(2)链板节距不同外壳高度H1最小高也不同；
节距31.75mm外壳最小高度H1100mm;
节距38.1mm外壳最小高度H1135mm;
节距50.8mm外壳最小高度H1180mm;
节距63.5mm外壳最小高度H1 230mm;
节距101.6mm外壳最小高度H1260mm;
(3)排屑机水箱的具体外形尺寸可根据用户要求制做成不同形状。
(4)可根据用户实际不同要求设计制造。
Note:
(1).Motor power can be determined by the effect -ive width of debris removal B2,levelness L1 and lifting height H.
(2).If the pich of the chain plate is different, the height of different cases H1 shall be differ -ent as well.
Pitch31.75mm Min.height of the case H1 100mm; Pitch38.1mm Min.height of the case H1 135mm; Pitch50.08mm Min.height of the case H1 180mm; Pitch63.5mm Min.height of the case H1 230mm; Pitch101.6mm Min.height of the case H1 260mm; (3).The overall dimensions of the water tank can be made in different appearances according to the client requirement.
(4).It can be designed and fabricated according to the client requiements.
CXBP型磁性板式排屑机 CXBP type magnetic debris removal unit
●CXBP型系列磁性板式排屑机结构紧凑，运转平稳，噪声低，最适宜输送的是吸磁的颗粒状，块状切屑以及长度小于150mm的断屑。该机器的主要工作元件磁场强大，使其具备良好的排屑性能，此排屑机属于定量排屑，即每组磁性材料能够吸附吸屑的最大量是固定的。即使工作面上堆积了更多的切屑它也是按固定的排屑量进行输送。另外，该排屑机的运动部件全部封闭在壳体内部，工作面板上有非切屑异物时，也不会导致机器卡滞、过载。
●采用自动张力结构，自动调整链条松紧度。
CXBP type magnetic debris removal unit is of compact in structure, smooth operation and low noise so that it is suitable for magnetic particles,block debris and fine debris with a length less than 150mm.The main parts of this unit have strong magnetic field.This unit removes debris at a pre-set amount.That is to say,each group of the magnetic material can attract a max.amount of debris.Debris is transmitted at a pre-set intervals even if debris is accumulated on the workdesk.All of the parts of this unit are enc -losed totally in the case so that machine will not be overloaded or hurt w -hen non-cut foreign materials appear on the working plate.
Auto-Tension stucture is used,which is able to adjust the degree of tightn -ess of the chain.
CXBP型磁性板式排屑机 CXBP type magnetic debris removal unit
CXBP型磁性板式排屑机外形尺寸图 Overall Dimensions Drawing of CXBP type magnetic debris removal unit
技术参数
Technical parameters
单位:mm
| 主要技术参数 Main Technical Parameters | 辅助技术参数 Auxiliary Technical Parameters | ||||||||||||||
| 代号 code | L | L1 | L2 | B | B1 | B2 | α | H | H1 | H2 | H0 | L3 | 电机功率KWMotorpower | 外壳颜色Shellcolor | 排屑量可根据用户实际要求增加运行速度或增加磁性密度Debris dischargeamount can bedetermined accordingto the clientrequirement by wayof increasing theoperating speed oradding moremagnets. |
| 名称 Name | 总长度Totallength | 接屑长度Debriscollectionlength | 水平长度Horizontallength | 外壳宽度Shellwidth | 接屑宽度Widthofcollectingthedebris | 有效排屑宽度Effectivewidth ofdebrisremoval | 提升高度Lifting high | 提升高度Liftinghigh | 外壳高度Shell height | 水平高度Horizontal | 支腿高度Supportingleghigh | 支腿距离Supporting legdistance | |||
| 尺寸Dimensions | |||||||||||||||
| 水箱技术参数 Water tank technical parameters | ||||
| 名称name | 水箱长度Length ofwater tank | 水箱宽度Width ofwater tank | 水箱高度Height ofwater tank | 冷却泵流量L/minFlowrate ofcoolingpump |
| 尺寸dimensions | ||||
Note:
(2)链板节距不同外壳高度H1最小高也不同； 节距38.1mm外壳最小高度H1170mm; 节距50.8mm外壳最小高度H1180mm; 节距63.5mm外壳最小高度H1 230mm;
(3)排屑机水箱的具体外形尺寸可根据用户要求制做成不同形状。
(4)可根据用户实际不同要求设计制造。
(1).Motor power can be determined by the effective width of debris removal B2,levelness L1 and lift -ing height H.
(2).If the pich of the chain plate is different,the heig -ht of different cases H1 shall be different as well. Pitch38.1mm Min.height of the case H1170mm; Pitch50.8mm Min.height of the case H1180mm; Pitch63.5mm Min.height of the case H1 230mm;
(3).The overall dimensions of the water tank can be made in different appearances according to the client requirement.
(4).It can be designed and fabricated according to the client requiements.
LXP型螺旋式排屑机 LXP Spiral Type debris removal unit
●LXP型螺旋式排屑机结构紧凑，占地空间小，安装使用方便，传动环节少，故障率极低，该机器适用于排屑空间狭小，其它排屑形式不易安装的位置，可与其它形式的排屑机组合使用，以达到改变方向的高度效果。对金属、非金属的断屑、块状屑及碎屑均有良好的输送功能。
驱动装置位于机器的接屑端，出料口位于远离驱动电机端，配锥状导料管可以将物料提升输送，通过在壳体水平工作处开回流孔的方法，还可以完成切屑与冷却液的分离，实现一机多用。
●不适合输送卷屑，出料口位于远离驱动电机端，配锥状导料管可以将物料提升输送，通过在壳体水平工作处开回流孔的方法，还可以完成切屑与冷却的分离，实现一机多用。
LXP spiral type debris removal unit is of compact structure design and ne -eds less floorage for installation and operates conveniently,less rotating parts and less troubles,This unit is suitable for tight installation space whi -ch are not suitable for other types of debris removal units.It works very well in terms of the transmission of metal debris,non-metal debris,blocklike debris or fine debris.
The drive device is installed at the debris collecting end of the machine. The discharge is away from the electric motor.Cone-shape hose is provi -ded to lift up the debris for transmission.Debris can be separated from the cooling liquid by way of the reflux hole on the case.This unit functions for multiple applications.
It is not qppropriate for conveying curly debris,otherwise twine could occur.
不适合输送卷屑，会发生缠绕现象。
LXP型螺旋式排屑机 LXP Spiral Type debris removal unit
LXP型螺旋式排屑机外形尺寸图 Overall Dimensions Drawing of LXP spiral type debris removal unit
A型有芯式
技术参数
单位:mm
| 尺寸dimensions型号Type | 主要技术参数 Main Technical Parameters | 辅助技术参数 Auxiliary Technical Parameters | 水箱技术参数 Water tanktechnical parameters | 电机功率KWMotorpower | 排屑量kg/hAmountof debrisdischarge | ||||||||||
| 螺旋直径AScrewdiameter | 排屑槽直径BDiameterof debrsremovaltank | 水平长度LHorizontallength | 排屑槽高度CHeightof debrsRemovaltank | 螺距Ppitch | 提升角度aLiftingangle | 排屑槽总宽DTotalwidth ofthedebrisremovaltank | 提升高度HLiftingheight | 排屑口高度H1Height ofthedebrisdischargeoutlet | 出口长度L1Lengthof theoutlet | 水箱宽度FWidthofwatertank | 水箱高度Eheightof watertank | 水箱长度GLengthofwatertank | |||
| LXP-72 | ①72 | Φ80 | ≤5m | 用户自定By user | 60 | ||||||||||
| LXP-80 | ①80 | Φ100 | 80 | ||||||||||||
| LXP-100 | Φ100 | Φ120 | ≤10m | 100 | |||||||||||
| LXP-120 | Φ120 | Φ150 | 120 | ||||||||||||
| LXP-150 | Φ150 | Φ180 | ≤15m | 150 | |||||||||||
| LXP-200 | Φ200 | Φ230 | 200 | ||||||||||||
| LXP-X | ①X | ΦX+40 | |||||||||||||
X表示根据用户实际需要特殊度设计的参数。该排屑器各个尺寸均可根据用户需要另行设计。
Note:motor power can be determined by diameter A of the blade and the horizontal length L.
Xrepresents the special parameters set forth according to the client requiements.dimensions of this type debris removal unit can be determined according to the client requirements.
工作灯系列Work light series
1. LED POWER 06 系列是专门针对中小型工业设备设计的SMD LED灯具。
2. 此款灯具有寿命长，照度高，可靠性高等特点，安装方便。
3.全金属外壳设计，钢化玻璃灯罩，安装角度可调，是一款外形美观，适用性强，性价比高的机床照明灯具。
| 型号Model | 标称功率Nominal lightpower(W) | 使用光源Light source | 窗口尺寸Cover length(mm) | 电压Voltage(M) | 光源光通量TUBE Lumens(lm) | 色温Colortemperature | 灯罩材质Lamp covermaterial | 长度尺寸LengthL(mm) | 安装尺寸LengthL1(mm) | 高度尺寸HeightH(mm) | |
| LED POWER 060 | DC24V | 4000K/6400K | GLASS | 265 | 65~245 | 65 | |||||
| LED POWER 060-1 | 12W | SMD LED | 230×35mm | AC110V | 1440lm | ||||||
| LED POWER 060-2 | AC220V | ||||||||||
| LED POWER 061 | 16W | SMD LED | 330×35mm | DC24V | 2016lm | 4000K/6400K | GLASS | 365 | 65~345 | 65 | |
| LED POWER 061-1 | 35mm | AC110V | |||||||||
| LED POWER 061-2 | AC220V | ||||||||||
| LED POWER 062 | 20W | SMD LED | 430×35mm | DC24V | 2304lm | 4000K/6400K | GLASS | 465 | 65~445 | 65 | |
| LED POWER 062-1 | AC110V | ||||||||||
| LED POWER 062-2 | AC220V | ||||||||||
| LED POWER 063 | 28W | SMD LED | DC24V | 3456m | 4000K/6400K | GLASS | 665 | 65~645 | 65 | ||
| LED POWER 063-1 | 630×35mm | AC110V | |||||||||
| LED POWER 063-2 | AC220V | ||||||||||
| LED POWER 064 | 36W | SMD LED | 830×35mm | DC24V | 4320lm | 4000K/6400K | GLASS | 865 | 65~845 | 65 | |
| LED POWER 064-1 | AC110V | ||||||||||
| LED POWER 064-2 | AC220V | ||||||||||
软连接系列Soft connection series
规格尺寸：一般为DN100-2500mm，长度1000-10000mm（产品规格材质可根据客户的需求及用途制作)。钢丝0.8-5.0mm。
材质：进口帆布、硅胶布（布料颜色：军绿色、 白色、灰绿色、银灰色、红色)
特性：①具有耐磨损、耐酸碱、耐温、耐高压等特点(耐温约-25℃-+350℃不等，最大耐压350MMWG，标准长度10m)
③高伸缩弯曲性，安装施工容易。
连接方式：法兰连接（角钢、A3钢板、不锈钢、PVC)、套箍连接。
风道通风除尘软连接的应用：
水泥散装水泥伸缩袋、输送管，散装水泥软连接采用10\*10的纯棉帆布为主料，散装水泥软连接衬托骨架选用φ5-8mm的钢丝。因此同现有技术相比，本实用新本产品由尼龙布，绝缘卷材，橡胶附和布，防油布，防水布，阻燃布、耐酸碱布等多种材质可供客户不同需求来量身定做。
产品特点：
■无硬力传递非高温软连接产品采用柔性材料构成,因此消除了硬力传递,优化了管路系统设计,延长了管路设备的使用寿命。
高温软连接在运行过程中随着温度的急剧变化会产生多方向偏移。非金属软连接能在较小空间内提供全方位补偿。
散装机伸缩帆布袋主要用于固体粉末的包装和回收，如水泥散装，粉尘卸料等，通常由内筒和外筒两件组成一套，内筒用于包装，外筒用于防尘，通常内筒直径在300左右，外筒直径在700左右，长度因各个厂家的要求而有所不同。我公司生产的伸缩布袋伸缩布筒带固环散装收缩袋产品具有透气均匀、尺寸稳定寿命长、节能等优点。
产品特点：
水泥散装水泥伸缩袋、输送管，散装水泥软连接采用10\*10的纯棉帆布为主料，散装水泥软连接衬托骨架选用φ5-8mm的钢丝。因此同现有技术相比，本实用新本产品由尼龙布，绝缘卷材，橡胶附和布，防油布，防水布，阻燃布、耐酸碱布等多种材质可供客户不同需求来量身定做。
选用材质：
红色硅胶玻璃纤维风管硅胶涂面玻璃纤维风管、焊锡高温软管、高温防火软接。用途：各种机械设备(各种干燥机，烘箱，注塑机，高温整烫).尘埃、高温气体、粉末抽排通风换气等。它具有防静电，耐酸碱、化学废气、阻燃、耐磨、耐拉及任意伸缩万向转变等功能。
软连接系列Soft connection series
说明：
G1/4"每只长度为13mm
G1/4 " 13mm per peice
G3/8"每只长度17.5mm
G1/2"每只长度21mm
G3/8 " 17.5mm per peice
G1/2 " 21mm per peice
| D1 | d1 | d2 | D2 | L | 备注Remarks |
| L31-5G1/4″ | 1.5 | 18 | 14 | 280 | 可任意选用长度Lengthforselection |
| 3 | |||||
| 4.5 | 25 | ||||
| L31-5-G3/8″ | 6.5 | 32 | 21 | 410 | |
| 40 | |||||
| L31-5-G1/2" | 6.5 | 50 | 24 | 410 | |
| 10 |
GXB型机床导轨刮屑板
Gxb machine tool guide rail scraping plate
标准长度为500mm-1000mm的导轨刮屑板，采有铝合金、不锈钢板型材骨架和聚氨脂弹性体刮舌。具有外观造型美，耐油、耐磨、耐冷却、防老化和刮舌自动补偿等特点。可根据不同的导轨形状组成直角形、燕尾刮屑板组合件。
| 型号Model代号Code | GXB-20 | GXB-25 | GXB-30 | GXB-35 |
| H | 20 | 25 | 30 | 35 |
| A | 6 | 6-10 | 6-15 | 6-20 |
| d | 5-6 | 5-7 | 5-7 | 5-7 |
圆型、方型、八角型护罩分类
Classification of round, square, and octagonal protective covers
特点：
圆形防护罩外用橡胶尼龙内加PVC片式钢丝圈支撑可防尘、水、油、防腐蚀，外形美观，可在高温110°低温-40°之间正常使用，直径大小，行程长短可根据用户要求安排生产。
Characteristics:
Rubber nylon and PVC steel rings are used in fabricating the round-shaped protecting covers, which is dust resistant, water proof, oil resistant and corrosion proof. This product can work properly the temperature range of 110℃\~ -40℃. The length of the travel range can be set according to the customer's request.
1. 在两边有一层坚硬的保护环 4. 圆护罩支撑钢丝圈
2. 焊接口和缝合线 5. 平的边缘
3. 聚氯乙烯支撑环；每折一片 6. 颈口
1. Rigid polyamide or kevlar rings coated on both sides.
2. Seams or weldings.3. PVC supporting shoes.
4. Steel rings for the bigger bellows.
5. Flat flange.6. Collar.
Design data for rubber shield
| 代号Code | 名称Description | 数据Data | 备注Remarks | 代号Code | 名称Description | 数据Data | 备注Remarks |
| Lmax | 拉伸后长度Length after drawing | D | 外圈直径Outside diameter | 橡胶Rubber | |||
| Lmin | 收缩后长度Length after compression | D{1 | 内圈直径Inside diameter | 用户自定By user | |||
| $\mathsf { L } _ { \mathsf { \Pi } _ { 1 } }$ | 下部连接长度Underside for connecting length | d | 连接处外径O.D Of the connecting point | ||||
| L2 | 上部连接长度Upper connecting length | d1 | 连接处内径I.D Of the connecting point |
阻燃耐高温圆形伸缩护罩
Flame retardant high temperature resistant shape telescopic shield
可以用来对丝杠、光杠、立柱、心轴及其它的圆形旋转柱体进行防护及高温通风。起到软连接的作用。可以水平或垂直使用。水平使用时建议使用塑料或铝的支撑环，保持护罩内腔与丝杆之间有一定均匀的距离，延长使用寿命。拉伸长度大时可以在每个折中加上金属环，提高护罩的稳定性。连接或固定端通常使用金属法兰盘，也可以选择套箍式。我公司是一家真正集生产、销售于一体的大型厂家。本公司所生产的高温伸缩防护罩具体材料及耐温程度如下：
| 材质 | 耐温度 |
| 橡胶布高温伸缩防护罩(颜色黑色) | -40度---(+85度) |
| 增强尼龙布(颜色黑色、银灰色、白色、绿色) | -40度---(+145度) |
| 280三防布(颜色绿色、灰色、黄色) | -30度---(+180度) |
| 高温帆布(颜色绿色) | -30度---(+230度) |
| 单层硅胶玻璃纤维布(颜色灰色、红色) | -30度---(+330度) |
| 双层硅胶玻璃纤维布(颜色灰色、红色) | -30度---(+380度) |
| 矽胶涂面玻璃纤维布(颜色银灰色) | -30度---(+500度) |
| 矽胶蛭石双层复合材质(颜色外银灰色内淡黄色) | -30度---(+900度) |
| 矽胶高硅氧双层复合材质(颜色外银灰色内淡黄色) | -30度---(+1100度) |
拉链式丝杠防护罩缝合式防尘套
Zipper type lead screw protective cover suture type dust boot
拉链式丝杠防护罩缝合式防尘套是防护罩的一种又称为丝杠防护套，它可有效地保护丝杠、光杠、轴、立柱等零部件不受灰尘等外特的污染与破坏。
丝杠防护罩工艺分类：
按制作工艺分为钢圈支撑式、缝制式。
按形状分为筒式、塔式、方形、矩形、椭圆形、楼梯形、弯月形、半圆形等各种形状。
按连接方式又可分为（1)两头领口（卡箍式)(2)两头法兰（螺丝式)(3)一头法兰，一头领口。法兰又可分为PVC法兰和金属法兰。
盐山县盛达机床附件有限公司
地址：河北省盐山县庆云小杨工业园189号
电话：0317-6344266
手机：13931711407 13931752756
网址：www.yshengda.com
邮箱：yasdjcfj@126.com
