RH-07 Installation Guide & User Manual<br>Smart door Lock installation diagram

Installation of the Spindle

Based on the surface of the door, put the spindle through the hole to the outdoor panel, and the indoor outer part should not more than 5mm, and not less than 3mm.

Procedures of Installation

1.Holes & Groove Drilling

(1) Holes Drilling: according to the holedrilling-chart, drill holes for panels and lock cylinder.

(2) Grooves Drilling: to drill grooves on the side of the door for the plate & lock body.

2.Lock body & Lock cylinder installation

(1) Change the turning of the latchbolt according to the door opening direction.

(2) Put the lock body into the groove, don't forget to connect the hooks if the door has up & down bolts.

(3) Insert the lock cylinder and fix it onto the door by a screw on the side.

3.Outdoor Panel Installation

(1) According to the direction of the door opening, change the direction of the handle on the panel.

(2) Screw up the studs onto the backside of the outdoor panel;

(3) Put the wire through the hole from the outdoor panel on the door, and insert the spindle as well;

(4) Use the screws to fix the outdoor panel onto the door by connecting to the rear basement fixing panel.

4.Direction changing for the indoor handle

1. Put out the turning panel (Note: just install it back when it's done)

2.Put out the screw (Note: Just install it back when it's done)

5.Indoor Panel Installation

(1). Plug the wire from the outdoor panel onto the socket on the indoor panel.

(2). Put the spring into the handle of indoor panel, and insert the knob bar & spindle into the relative holes.

(3). Fix the indoor panel onto the door, and insert the batteries before

putting on the cover.

6.Adjustment after installation

(1) Unlock the door by fingerprint or password or IC card. Meanwhile, turn the handle and reverse it if available for checking its smoothness.

(2) Unlock the door by the mechanical key in order to check its normality and correctness.

Anti-burglar function:

If switch to the side “unlock", indoor handle can unlock the door; If switch to the side “lock”, antiburglar mode, indoor handle cannot unlock the door.

Delete Fingerprint

On the TTLock APP, click “fingerprint” ----> click the one to delete ---> confirm to delete.

On the smart lock enter “”70“”-----> admin password ---->“” then delete all fingerprints.

Modify the name of fingerprint

On the TTLock APP, click “fingerprint” ----> click the fingerprint to modify---- >click to change ----> enter new name ---> click save

Modify the valid date of fingerprint

On the TTLock APP, click “fingerprint” ---> click the fingerprint to modify -----> click to change ----> enter new valid date ---> click save

Add password

On the TTLock APP, click “password' -----> click on the right top to choose “generate password"-\_--> enter the name & valid time ----> click “complete” to finish

Note: For the password, it can set as “permanent / valid time / one-time / erase / custom / recurring.

Just press the reset button after removing the battery cover ---> enter admin password--->“”-\_\_--> enter the password what you need ---->“ ”-\_\_--- re-enter again ---->“”

Note: You can “upload passwords” from those what you set on smart lock to TTLock APP and manage. (click “password"-----> click on the right top to choose “upload password”)

Delete password

On the TTLock APP, click “password” ----> click the password to delete ---> click “delete” and confirm.

On the keypad enter“”71“”delete all “passwords” (except admin password).

Modify the password

On the TTLock APP, click “password” ----> click the password to change ----> enter the password ---> enter new password.

On the keypad enter “”10“” ----> old password “” new password ----> “”-\_--> new password ----> “”. if to change admin password, then enter “”12“”to change

Modify the name of password

Modify the valid date of password

Add IC cards

On the TTLock APP, click “IC cards' -----> click on the right top to choose “add IC card"----> enter the name & valid time ----> put the card to the identify area to finish

Note: For the IC card, it can set as “permanent / valid time .

Just press the reset button after removing the battery cover ---> enter admin password--->“"------> according to the voice announce, put the card to the identify area to add

Note: You can “upload IC Cards” from those what you set on smart lock to TTLock APP and manage. (click "IC cards"-----> click on the right top to choose “upload IC Card")

Delete IC Cards

On the TTLock APP, click “IC Cards” ----> click the IC Card to delete ---> click “delete” and confirm.

On the keypad enter “”69“”admin password,“”delete all “IC cards”.

Features

1. Adopt semi-conductor fingerprint sensor, lighting up by any touch.

2. With voice announce operation (English or Chinese)

3. Power supply to be 4pcs alkaline batteries, and with Micro USB interface for emergency recharge on the outdoor panel.

4. Intelligent update function of fingerprint information can effectively improve users' experience.

5. Password to be 6-12 digits, and with virtual password for anti-peeping

6. User capacity: 100 fingerprint +150 password

\+ 200 IC card.

7. Built-in doorbell function & Low battery alert

8. Restore the factory setting is available.

Scan the QR code to download the TTLock APP

Factory setting

The factory default password is 123456. Open the battery cover on the indoor panel, keep pressing the “reset” button 5 seconds, then voice announce “pls inert initial password”, enter 000“ "then it restore to be factory setting.

■Setup Administrator's password

Remove the battery cover, press the “reset” button----> insert admin password“”\_--> re-insert again “”.

Note:If use the TTLock APP to manage,then this setting above may not use.

IModify Admin password

On TTLock APP----> setting ---->basics -----> Admin passcode -----> enter new admin passcode.

Be sure to operate within 1 meter near the smart lock.

On the keypad, entering “”12“”,old admin password“”,new admin password“”, re-enter new admin password“”, to modify Admin password.

lAdd mobile admin

If first time to setup the Admin, touching the keypad, connect to the mobile, use TTLock APP to manage.

If having set the admin password on the lock, but no connect the TTLock APP, press the reset button after removing the battery cover----->enter admin password “”-\_-->again press the reset button ----> voice announce “pls add mobile admin", then operate the TTLock APP on the smartphone.

If having set the admin password or added the mobile admin, then on the keypad enter“"83“”admin password“”as to add mobile admin mode again, then allow somebody to use another TTLock APP account to connect this smart lock and become the new admin.

Note:Once new TTLock APP account added the admin successfully, the former (old) mobile admin would be invalid. That is, it's only one account to be the mobile admin.

Delete mobile admin

On the TTLock APP, click “setting”, and choose "delete Admin".

Note:Once mobile admin deleted, the lock restore to factory setting, then all users and unlocking records (fingerprints, passwords, IC cards) will be deleted.

lAdd Fingerprint

On the TTLock APP, click “fingerprint"----> add fingerprint ---->enter the name and valid date for this fingerprint ---> click “the next” -----> click “add"--- --> accordingthe notice and voice announce, put the finger onto the sensor to add.

Or just press the reset button after removing the battery cover---> enter admin password “”\_> according the voice announce, put the finger onto the sensor to add.

Note:To add fingerprint, you can manage it on the TTLock APP, or just operate it on the smart lock.

Modify the name of IC Card

On the TTLock APP, click “IC Cards” ----> click the IC Card to modify---->click to change ----> enter new name ---> click save

Modify the valid date of IC Card

On the TTLock APP, click “IC cards” ---> click the IC card to modify -----> click to change ----> enter new valid date ---> click save

Unlocking

App unlocking : click the unlocking icon on the TTLock APP to unlock

Note: This must be done near the lock; If with Gateway connection, then can enable the remotely unlocking function.

IC card unlocking: use the added IC card to unlock

Fingerprint unlocking: use the added fingerprint to unlock

Password unlocking: use the added password to unlock

Note: During the password entering, if wrong pressing, then press “" to delete.

Factory default password is 123456

Locking

After unlocking, 5 seconds later it will locked itself automatically. (except the passage mode).

At passage mode, long press “”to disable.

ITemporary passage mode

After unlocking (before locking itself), enter 123“”, it comes to be passage mode.

IAPP Key

On the TTLock APP, click “send key”, and send such “key” to other user for authorization.

Virtual password

When entering password, you can add any numbers before or after the correct password to unlock, total numbers is max. 16 digits.

Unlocking records

On the TTLock APP, you can click “records” to check all the unlocking records.

Note: If no Gateway connection, all the unlocking records just can be checked after unlocking.

ISystem blocked

(1) If wrong input fingerprint 3 times, the lock system will be alarming; and the fingerprint system will be blocked after 5 times entering wrong fingerprint. Voice announce “fingerprint system is frozen”(3 minutes blocked)

(2)If wrong input password 3 times, the lock system will be alarming, and the passwordsystem will be blocked after 5 times entering wrong password. Voice announce “password system is frozen” (3 minutes blocked).

ILanguage setting

Emergency power supply

Once battery is using up and no bring the mechanical key at hand, you can use the(DC 5.0V) power-bank to recharge the battery before you can unlock it by fingerprint or password again.