Masonry Veneer

Installation System

Product Selection Catalogue

Snap for more

information.

Adhered Masonry Veneers

Natural Stone

Thin Brick

Manufactured Stone

Globally Proven Construction Solutions

LATICRETE Masonry Veneer Installation System Warranty

See www.laticrete.com.au/warranty for complete warranty information.

Enjoy peace of mind with high quality, world renowned LATICRETE Products.

Consider the extra value and peace of mind a LATICRETE Warranty can bring when selecting the

installation system for your project.

LATICRETE provides comprehensive warranties for commercial, residential and industrial project

worldwide. However, our best guarantee is our 60 Years of experience with these commercial, residential

and industrial installation in every imaginable climate, in just about every country around the world.

LATICRETE Australia warrants that LATICRETE products will be free from manufacturing defects and

will not break down or deteriorate when installed in accordance with LATICRETE written specification

and guidelines. Efflorescence is a natural condition of Portland cement and is not a defective condition.

This warranty is not transferable or assignable. Keep invoices and receipts as proof of purchase. This

warranty is limited to defects in our products. LATICRETE is not liable for any incidental damages or

consequential damages including losses due to delays, incurred by the purchaser or any other party.

This warranty does not cover any defects caused by an accident, misuse, abuse, improper installation,

lack of reasonable care, unauthorised modification, tampering or attempt to repair by a person not

authorised by the original applicator; or any product that has been used for purpose other than its

intended use. This warranty is limited to products supplied by LATICRETE Australia.

For these limited warranties to apply, the applications that comprise the installation must be performed

with the products listed in the particular document for each application (refer to the charts on this page).

For Consumers as defined by the ACL, the benefits conferred by this warranty are in addition to all

rights and remedies in respect of the product that the consumer has under the Competition and

Consumer Act 2010 and similar state and territory laws. Our goods come with guarantees that cannot

be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure.

LATICRETE 15 Year System Warranty

APPLICATION PRODUCTS

Underlayment 3701 Fortified Mortar Bed

3701 Mortar Admix mixed with

∙ 226 Thick Bed Mortar

Moisture Shield LATAPOXY® Moisture Shield

Waterproofing/Anti-Fracture HYDRO BAN®

Thick Bed Method 3701 Fortified Mortar Bed

3701 Mortar Admix mixed with

∙ 226 Thick Bed Mortar

Thin Bed Method MVIS™ Masonry Veneer Mortar

Grouting MVIS™ Masonry Veneer Pointing Mortar

PERMACOLOR® Grout

Sealant LATASIL™ and LATASIL 9118 Primer where required

System Warranty

15 YEAR*

LATICRETE Australia Pty Ltd

29 Telford Street, Virginia, QLD 4014 Australia ■ 1800 331 012 ■ www.laticrete.com.au

© 2018 LATICRETE Australia Pty Ltd. All trademarks shown are the intellectual properties of their respective owners.

DS-1242-0518 *United States Invention Patent No.: 6881768 (and other Patents).

MVIS™ Masonry Veneer Installation

System Warranty

| 2

4 | www.laticrete.com.au/MVIS THE CHALLENGE

Up to now, the installation of manufactured stone masonry veneer has often

depended on the use of site-mixed unfortified masonry mortars that are subject

to large variations in consistency, quality and performance and which also limit

the installation technique to that of traditional masonry. Many projects have been

plagued by delaminating stone and water intrusion among other installation issues

inherent to materials and techniques which are limited in flexibility and margin for

error. This traditional method is not engineered as part of a complete wall system

and therefore does not offer warranties from a reliable source willing to stand

behind the installation.

The explosive increase in popularity of adhered masonry veneer facades has

created a need for higher performance, factory produced installation materials to

assure consistently high quality installations.

THE SOLUTION

Realising these shortcomings, and based on our globally proven technology, LATICRETE

has developed an installation system that provides a permanent, high strength

installation that is freeze/thaw stable and protected from water intrusion.

Backed by the LATICRETE® System materials, the LATICRETE Masonry Veneer

Installation System (MVIS™) allows for increased productivity utilising either traditional

masonry installation techniques or the “tiler’s method”.

Vastly expanded architectural details are offered at www.laticrete.com.au/MVIS to

help design professionals, contractors and installers understand the range of possible

applications – and appropriate products and techniques which will assure long-term

performance on projects of all types.

MaVOCn nnn LATlabosubLATto sn LAreLATConcomto hfailu1 Scratch Coat/Brown Coat

2 Waterproofing

3 Adhesive

4 Masonry Pointing Mortar

5 Flexible Sealant (for movement joints)

1 3

4

3 2

5

4 | www.laticrete.com.au/MVIS | 3

THE CHALLENGE

Up to now, the installation of manufactured stone masonry veneer has often

depended on the use of site-mixed unfortified masonry mortars that are subject

to large variations in consistency, quality and performance and which also limit

the installation technique to that of traditional masonry. Many projects have

been plagued by delaminating stone and water intrusion among other

installation issues inherent to materials and techniques which are limited in

flexibility and margin for error. This traditional method is not engineered as part

of a complete wall system and therefore does not offer warranties from a

reliable source willing to stand behind the installation.

The explosive increase in popularity of adhered masonry veneer facades has

created a need for higher performance, factory produced installation materials

to assure consistently high quality installations.

THE SOLUTION

Realising these shortcomings, and based on our globally proven technology,

LATICRETE has developed an installation system that provides a permanent,

high strength installation that is freeze/thaw stable and protected from water

intrusion.

Backed by the LATICRETE® System materials, the LATICRETE Masonry Veneer

Installation System (MVIS™) allows for increased productivity utilising either

traditional masonry installation techniques or the “tiler’s method”.

Vastly expanded architectural details are offered at www.laticrete.com.au/

MVIS to help design professionals, contractors and installers understand the

range of possible applications – and appropriate products and techniques which

will assure long-term performance on projects of all types.

1 3701 Fortified Mortar Bed

Scratch Coat/Brown Coat

2 HYDRO BAN® Waterproofing

membrane

3 Masonry Veneer Mortar

4 Masonry Pointing Mortar /

PERMACOLOR® Grout

5 Flexible Sealant (for movement joints)

Masonry Veneer Installation Product Guide

4 | www.laticrete.com.au/MVIS

DETAIL LEGEND

Masonry Veneer Installation Product Guide

2 | www.laticrete.com.au/MVIS LATICRETE ® MVIS™ Details

DETAIL LEGEND

Exterior wall

Concrete wall – Direct adhered with

fluid applied air and water barrier

Interior wall

Framed wall with cement backer board substrate

Exterior wall

Concrete wall – lath with scratch and brown coat

D C J

B A

H C

B A

F E D C

G

J

B A

A Adhered Masonry Veneer F Metal lath, 3.4# galvanized diamond wire lath

B Masonry Pointing Mortar G Cleavage membrane 6.5 kg builders felt or 0.10 mm polyethylene

C Masonry Veneer Mortar H Cement backer board

D HYDRO BAN® I Exterior rated sheathing

E 3701 Mortar Mix J Concrete or Masonry

2 | www.laticrete.com.au/MVIS 4 | Masonry Veneer Installation System Product Selection Catalogue | www.laticrete.com.au

EXTERIOR WALL

Concrete wall - Direct adhered with

fluid applied air and water barrier

INTERIOR WALL

Framed wall with cement

backer board substrate

A

A

A Masonry Veneer or Thin Brick

B Masonry Pointing Mortar/PERMACOLOR® Grout

C Masonry Veneer Mortar

D HYDROBAN®BAN

E LATAPOXY® Moisture Shield

F 3701 Fortified Mortar Bed

EXTERIOR WALL

Concrete wall - lath with scratch

and brown coat

G Metal lath, 3.4# galvanized diamond wire lath

H Cleavage membrane, 6.5 kg builders felt

I Cement backer board

J Exterior rated sheathing

K Concrete or Masonry

www.laticrete.com.au/MVIS | 5

NOTE: 1. Framed substrates scheduled to receive

manufactured stone, natural stone or thin brick must

be structurally sound, rigid and conform to good

design/engineering practices in accord with all

applicable building codes with maximum deflection

under all live, dead and impact loads, including

concentrated and all anticipated loads of L/600 for all

exterior veneer types. Steel and wood frame constructs

shall also be designed to meet this criteria. Lateral

bracing and edge support for cement backer board

panels is required. Install sheathing panels as directed

by board manufacturer’s installation instructions and

building code requirements.

2. Masonry Pointing Mortar is designed to meet product

applicable project specifications. Masonry Pointing

Mortar does not inhibit efflorescence from occurring in

natural or manufactured stone facade installations.

Efflorescence is a normal condition that may occur

when installing Portland cement based products.

During installation, strike joints in a consistent time

frame relevant to application time. Masonry Pointing

Mortar should be thumbprint dry before striking.

Striking joints too early or too late can create colour

inconsistencies.

3. Masonry Pointing Mortar colour samples are guides

only. LATICRETE does not warrant colour matching to

any colour guide produced. Actual shade and texture

will depend on job site conditions, lighting, installation

techniques, and types of tile or stone used. Verify

actual appearance and compatibility with a test area

before installing. Blend coloured mortars with different

control numbers. No claims for colour shade variations

will be honoured.

4. Please consult LATICRETE Technical Services for more

information. 1800 331 012, www.laticrete.com.au,

technicalservices@laticrete.com.au.

5. For information on pumpable scratch and brown coats,

contact LATICRETE Technical Services.

6. For complete application information and limitations

consult related Product Data Sheets and Execution

Statements related to these details and applicable

standards. See warranty Data Sheet DS-1242 for full

information and terms.

7. As a professional courtesy, LATICRETE offers technical

services free of charge. The user maintains all

responsibility for verifying the applicability and

suitability of the technical service or information

provided.

8. Design and placement of weather resistive barriers,

vapour retarders and air/water barriers to be detailed

by project design professional.

Masonry Veneer Installation Product Guide

www.laticrete.com.au/MVIS | 3

LATICRETE MVIS Details Exterior wall

Framed wall with exterior rated sheathing –

cement backer board substrate

Exterior wall

Framed wall with exterior rated sheating – lath with scratch and brown coat

Exterior wall

Concrete Masonry Unit (CMU) wall with skim coat –

Direct adhered with fluid applied air and water barrier

C

D

E G

F

I

B A

C

H D

I

B A

C

E D J

B A

NOTE: Substrates scheduled to receive manufactured

stone, natural stone or thin brick must be structurally

sound, rigid and conform to good design/engineering

practices in accord with all applicable building codes

with maximum deflection under all live, dead

and impact loads, including concentrated and all

anticipated loads of L/600 for all exterior veneer

types. Steel and wood frame constructs shall also

be designed to meet this criteria. Lateral bracing

and edge support for cement backer board panels is

required. Install sheathing panels as directed by board

manufacturer’s installation instructions and building

code requirements.

2. Masonry Pointing Mortar is designed to meet

product applicable project specifications. Masonry

Pointing Mortar does not inhibit efflorescence from

occurring in natural or manufactured stone facade

installations. Efflorescence is a normal condition

that may occur when installing Portland cement

based products. During installation, strike joints in a

consistent time frame relevant to application time.

Masonry Pointing Mortar should be thumbprint dry

before striking. Striking joints too early or too late

can create colour inconsistencies.

3. Masonry Pointing Mortar colour samples are guides

only. LATICRETE does not warrant colour matching

to any colour guide produced. Actual shade and

texture will depend on job site conditions, lighting,

installation techniques, and types of tile or stone

used. Verify actual appearance and compatibility

with a test area before installing. Blend coloured

mortars with different control numbers. No claims

for colour shade variations will be honoured.

4. Please consult LATICRETE Technical Services for more

information. 1800 331 012, www.laticrete.com.au,

technicalservices@laticrete.com.au.

5. For information on pumpable scratch and brown

coats, contact LATICRETE Technical Services.

6. For complete application information and limitations

consult related Product Data Sheets and Execution

Statements related to these details and applicable

standards. See warranty Data Sheet DS-1097 for

full information and terms.

7. As a professional courtesy, LATICRETE offers

technical services free of charge. The user maintains

all responsibility for verifying the applicability and

suitability of the technical service or information

provided.

8. Design and placement of weather resistive barriers,

vapour retarders and air/water barriers to be

detailed by project design professional.

www.laticrete.com.au/MVIS | 3

| 5

EXTERIOR WALL

Framed wall with exterior rated sheating

– lath with scratch and brown coat

EXTERIOR WALL

Framed wall with exterior rated sheating

– cement backer board substrate

EXTERIOR WALL

Concrete Masonry Unit (CMU) wall with skim coat –

direct adhered with fluid applied air and water barrier

Masonry Veneer Installation Product Guide

6 | Masonry Veneer Installation System Product Selection Catalogue | www.laticrete.com.au

See Data Sheet DS-1063 / DS-1046

3701 Mortar Admix / 226 Thick Bed Mortar

226 Thick Bed Mortar gauged when with 3701 Mortar Admix produces a shock resistant, fortified thick-bed mortar for

use in “Extra Heavy Duty” tile and paver installation. It is particularly well suited to installation where heavy vehicular

or mass transit traffic is expected.

PACKAGING

3701 Mortar Admix: 15 litre pail; 36 pails per pallet

226 Thick Bed Mortar: 20 kg bag; 56 bags per pallet

Refer to Data Sheet DS-1176

LATAPOXY® Moisture Shield

LATAPOXY® Moisture Shield is a 2 component, roller applied epoxy coating specifically designed to reduce moisture

vapour emissions in concrete and other substrates.

FEATURES/BENEFITS

n Easy to use - rolls on like paint

n Cures in 24hours

n Can be applied over green concrete (min. 7 days old)

PACKAGING 20 litre unit (10 litre Part A and 10 litre Part B); 32 units per pallet

Performance Level: BEST

3701 Fortified Mortar Bed

3701 Fortified Mortar Bed is a one-step polymer fortified blend of carefully selected raw materials, Portland cement and

graded aggregates. 3701 Fortified Mortar Bed does not require the use of latex admix; you only need to add water to produce

a thick bed mortar or render with exceptional strength. Save time and money by eliminating the need for job site measuring

and mixing of sand and cement to the proper ratio. A suitable alternative to 3701 Mortar Admix combined with 226 Thick

Bed Mortar.

PACKAGING 20 kg bag; 56 bags per pallet.

APPROXIMATE COVERAGE per bag

THICKNESS COVERAGE

10 mm 1 m2

Performance Level: BEST

Refer to Data Sheet DS-1000

| 7

Masonry Veneer Installation Product Guide

LATAPOXY® 310 Stone Adhesive

A two-component, high strength construction epoxy adhesive for spot bonding large format tile and stone on vertical surfaces,

for interior or approved exterior applications. Offers major advantages in terms of speed and productivity over mechanical

anchoring, plaster and wire, and the thin-set method of veneer installation. Available in standard and rapid set formulas. Easier

to install when compared to traditional methods – no drilling, cutting of kerfs or setting of pins – LATAPOXY® 310 Stone Adhesive

allows for quick, easy plumb adjustment while stone is in place to compensate for uneven walls and stone thickness variations.

LATAPOXY 310 Stone Adhesive is permanent; it will not fail or deteriorate over time and is ICC and IBC approved.

PACKAGING

Rapid: 5 litre of Part A and 5 litre of Part B. Packed 1 kit per carton; 40 kits per pallet. Available in rapid version only.

Standard: 10 litre of Part A and 10 litre of Part B. Packed 18 kits per pallet. Available in standard version only.

MIXING

Combine equal volumes of LATAPOXY 310 Stone Adhesive Part A and LATAPOXY 310 Stone Adhesive Part B (1:1). Do not

mix more than approximately 0.5 litre of LATAPOXY 310 Rapid Stone Adhesive at a time.

APPROXIMATE COVERAGE

Average Millimetres

out of plumb

LATAPOXY® 310

Stone Adhesive Thickness

Approximate

Coverage/10 litre Units

Plumb Wall 3 mm 3 mm thick 27 – 30 m2

6 mm 6 mm thick 14 – 16 m2

12 mm 12 mm thick 7 – 7.5 m2

Refer to Data Sheet DS-1036

Performance Level: BEST

HYDRO BAN®

HYDRO BAN® is a thin, load bearing waterproofing/crack isolation membrane that DOES NOT require the use of fabric

in the field, coves or corners. HYDRO BAN is a single component self curing liquid rubber polymer that forms a flexible,

seamless waterproofing membrane that bonds directly to a wide variety of substrates. HYDRO BAN is a certified low VOC

emitting product. HYDRO BAN is a highly extensible Class 3 membrane suitable for Immersed Installations, Internal Wet

Areas and External Above Ground use.

n Class 3 membrane in accordance with AS4858 & AS4654.1

n Anti-fracture protection up to 3mm

n Low VOC

n Easy to clean with water

n Compatible with most good quality tile adhesives.

PACKAGING

Commercial Unit: 15 litre pail; 36 pails per pallet, 3.8 litre pail; 4 pails per carton; 48 pails per pallet

APPROXIMATE COVERAGE

UNIT SIZE COVERAGE

15 litre pail 18 m2

3.8 litre pail 4.6 m2

Refer to Data Sheets DS-1042 and DS-1086

8 | Masonry Veneer Installation System Product Selection Catalogue | www.laticrete.com.au

Masonry Veneer Installation Product Guide

Performance Level: BEST

Masonry Veneer Mortar

Masonry Veneer Mortar is a patented, versatile polymer fortified adhesive mortar designed specifically for the installation of

adhered masonry veneer, stone and thin brick. A high performance mix provides maximum non-sag performance for vertical

installations and also obtains maximum bond strength to the substrate and selected veneers. Formulated for added strength,

Masonry Veneer Mortar offers exceptional workability. Meets and exceeds the requirements of AS ISO13007.1&2 as a

C2TS1

PACKAGING 20 kg bag; 56 bags per pallet; Grey.

APPROXIMATE COVERAGE Per 20 kg bag

VERTICAL APPLICATIONS m2

NOTCH TROWEL COVERAGE

6 mm x 9 mm notched trowel 5.5 – 6.2

12 mm x 12 mm notched trowel 4 – 4.5

Adhered Masonry Veneer Application Method 2.75 – 3.25

Refer to Data Sheet DS-1076

PERMACOLOR® Grout

The maximum performance available in a cement-based grout. Provides consistent colour, and antimicrobial protection to

resist stain-causing mould and mildew and contains Kevlar® for strength and durability. PERMACOLOR® Grout mixes with

water only (no additive required) and is easy to install. Ideal for both floors and wall joints from 1.5 mm to 12 mm. For

both interior, exterior and submerged applications. Meets and exceeds the requirements of AS ISO 13007.3 & 4 as a

CG2WAF classification.

COLOURS See Colour Chart on page 9 for a list of available colours.

PACKAGING 10 kg bag; 100 bags per pallet; 2 kg bag; 8 bags per carton (sold as a carton); 40 cartons per pallet.

Refer to Data Sheet: DS-1041

Masonry Pointing Mortar

A factory prepared, Masonry Pointing Mortar is designed to be mixed with water or a LATICRETE Latex grout enhancer.

Formulated from a blend of high strength Portland cement, graded aggregates, and colour-fast pigments. Provides a joint that

is dense, hard and durable.

COLOURS See Masonry Pointing Mortar Colour Chart on page 9 for a list of available colours.

PACKAGING 22.7 kg bag; 56 bags per pallet.

APPROXIMATE COVERAGE

213 – 229 linear m with 9 mm x 6 mm deep joint

Refer to Data Sheet DS-1075

9 | Masonry Veneer Installation System Product Selection Catalogue | www.laticrete.com.au www.laticrete.com.au/MVIS | 9

Masonry Veneer Installation Product Guide

LATASIL™

High performance, 100% silicone sealant designed for use in coves, corners, changes in plane and expansion joints in

exterior and interior applications of adhered masonry veneer. Can be used in fountains, water features and other wet area

applications. LATASIL™ conforms to ASTM C 920 and ASTM C 794 adhesion properties and inhibits the growth of stain-causing

mould and mildew in sealant joints with antimicrobial product protection.

COLOURS See LATASIL Colour Chart on page 9 for a list of available colours.

PACKAGING 305 ml cartridges; 6 cartridges per carton; 240 cartons per pallet.

APPROXIMATE COVERAGE Per cartridge

THICKNESS COVERAGE

6 mm x 6 mm 7.62 m

9 mm x 9 mm 3.35 m

LATASIL™ 9118 PRIMER

Increases adhesion for porous stone, submerged, and permanent wet area applications.

FEATURES/BENEFITS

n Ideal for harsh environments

n Ready to use

n Fast dry time.

PACKAGING 240ml tin; 5 tins per carton. Tins sold individually

Refer to Data Sheet DS-1074

Refer to Data Sheet DS-1185

10| www.laticrete.com.au/MVIS | 10

MASONRY POINTING MORTARS,

PERMACOLOR® GROUT & LATASILTM COLOUR CHART:

Bright White Mushroom Latte*

Chestnut Brown* Natural Grey River Rock*

Terra Cotta* Quarry Red* Raven*

*Special order colours

POINTING MORTAR AND SEALANT COLOUR GUIDELINES

Pointing Mortar and sealant samples are guides only. LATICRETE does not

warrant colour matching to this colour chart or to any colour guide produced.

Actual shade and texture will depend on job site conditions, lighting, installation

techniques and types of adhered masonry veneer used, and may vary from this

colour chart, colour channel kits and colour swatch on product packaging. Verify

actual appearance and compatibility with a test area before installing. Blend

pointing mortar with different control numbers. No claims for colour shade

variations will be honoured.

Note: Colour availability of all LATICRETE products are subject to change.

LATICRETE Masonry Veneer Installation Product Guide

| 11

* United States Invention Patent No.: 6881768 (and other Patents).

See www.laticrete.com.au/warranty for complete warranty information.

LATICRETE is a member of The Masonry Veneer Manufacturers Association

(MVMA), an organisation representing manufacturers and suppliers of

manufactured stone and brick veneer products.

The MVMA proactively seeks to advance the growth of manufactured masonry

veneer products through technical advocacy and awareness efforts.

n Supports the Development of ASTM Product and Installation Standards as

well as ICC-ES Codes and Standards

n Establishes Cooperative Relationships With NAHB, the Green Building

Council, LEED, AIA, ASLA and CSI

Many companies might say their products are low VOC, only one independently

certifies it – LATICRETE.

n Third Party GREENGUARD Certification, required to meet stringent indoor air

quality standards

n Certified by GREENGUARD for Children & Schools

n Helps contribute toward LEED certification

n Product certifications readily available at www.laticrete.com/green

LATICRETE is a member of The Masonry Veneer

Manufacturers Association (MVMA), an organisation

representing manufacturers and suppliers of

manufactured stone and brick veneer products.

The MVMA proactively seeks to advance the growth

of manufactured masonry veneer products through

technical advocacy and awareness efforts.

n Supports the Development of ASTM Product and

Installation Standards as well as ICC-ES Codes and

Standards

n Establishes Cooperative Relationships With NAHB,

the Green Building Council, LEED, AIA, ASLA and CSI

LATICRETE Australia Pty Ltd is a proud member of the Australian Stone Advisory

Association Ltd. Many of the ASAA’s core foundations reflect those from which

LATICRETE has built is global business over the last six decades. In particular,

we share the strong belief/commitment that professional yet unselfish

education is a major factor in building and sustaining the stone business… in

every phase of its being. Just as the ASAA “provide(s) information about the

Stone Industry and related technology for the public benefit and not for

particular businesses and make(s) the benefits of scientific research publicly

available,” we at LATICRETE are always ready and willing to help those eager to

learn the correct and most up-to-date methods of stone installation.

The installation solutions offered via our Masonry Veneer Installation System

(MVIS) have been formulated with today’s most cutting-edge technologies

combined with a worldwide track record that continues to be architecturally

accepted and globally proven. We look forward to sharing these solutions with

industry professionals.

www.laticrete.com.au/MVIS | 5

Many companies might say their products are low

VOC, only one independently certifies it – LATICRETE.

n Third Party GREENGUARD Certification, required

to meet stringent indoor air quality standards

n Certified by GREENGUARD for Children & Schools

n Helps contribute toward LEED certification

n Product certifications readily available at

www.laticrete.com/green

LATICRETE Pty Ltd is a proud member of the Australian Stone Advisory Association Ltd. Many of

the ASAA’s core foundations reflect those from which LATICRETE has built is global business over

the last six decades. In particular, we share the strong belief/commitment that professional

yet unselfish education is a major factor in building and sustaining the stone business… in

every phase of its being. Just as the ASAA “provide(s) information about the Stone Industry

and related technology for the public benefit and not for particular businesses and make(s) the

benefits of scientific research publicly available,” we at LATICRETE are always ready and willing

to help those eager to learn the correct and most up-to-date methods of stone installation.

The installation solutions offered via our Masonry Veneer Installation System (MVIS) have

been formulated with today’s most cutting-edge technologies combined with a worldwide track

record that continues to be architecturally accepted and globally proven. We look forward to

sharing these solutions with industry professionals.

LATICRETE is a member of The Masonry Veneer

Manufacturers Association (MVMA), an organisation

representing manufacturers and suppliers of

manufactured stone and brick veneer products.

The MVMA proactively seeks to advance the growth

of manufactured masonry veneer products through

technical advocacy and awareness efforts.

n Supports the Development of ASTM Product and

Installation Standards as well as ICC-ES Codes and

Standards

n Establishes Cooperative Relationships With NAHB,

the Green Building Council, LEED, AIA, ASLA and CSI

LATICRETE offers a complete range of comprehensive System Warranties. These cover 100%

labour and materials for Masonry Veneer Installations Systems over concrete and masonry

substrates for both interior and exterior applications.

LATICRETE Warranties cover any suitable tile or stone manufacturers product, allowing you

to select the appropriate product and finish you desire for your project.

n LATICRETE Customisable System Warranties are available to suit your specific project

requirements.

LATICRETE goods come with guarantees that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or refund for a major failure and for

compensation for any other reasonable foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

www.laticrete.com.au/MVIS | 5

&

DS-1096-0718

LATICRETE Australia Pty Ltd | 29 Telford Street, Virginia, QLD 4014 Australia | 1800 331 012 | www.laticrete.com.au

©2018 LATICRETE Australia Pty Ltd | All trademarks shown are the intellectual properties of their respective owners.