该页无缩略图
Industrial Welding Solutions
Efficient,Reliable,Professional
Digital Panel
STRONG PERFORMANCE,STRONG CUTTING
COLDER 200
Digital inverter pulse colder
| Model | COLDER-200 | COLDER-250 | |
| Ratedsupplyvoltage | 1P,AC220V | 1P,AC220V | |
| Ratedsupply frequency | 50Hz/60Hz | 50Hz/60Hz | |
| Rated input Power | 8.7KVA above | 12.3KVA above | |
| Maximumno-loadvoltage | 94V | 94V | |
| output current | MAX | DC15-160A | DC15-180A |
| TIG | DC10-200A | DC10-250A | |
| outputvoltage | MAX | 26.4V | 26.4V |
| TIG | 18V | 18V | |
| Dutycycle(10 minutes)MMA/TIG | 35% | 35% | |
| Insulation class | H | H | |
| Coolingsystem | Forced air cooling | Forced air cooling | |
| Welding parametermemory | 5sets | 5sets | |
| Torchswitchreceptacle | 2pin | 2pin | |
| Input cable | 3.5mm2 | 3.5mm2 | |
| Packge dimensions | 545*280*550mm | 545*280*550mm | |
| Machineweight | 11.8kg | 14kg | |
| Weldable thicknessofstainless steel | 0.5-4mm | 0.5-4mm | |
Rotary Panel
IGBTINVERTERPULSETIG/MMA/PLASMACUT
SUPER 200P
Super (tig/mma/plasmacut)
| Model | SUPER-200P | SUPER-250P | |
| Input voltage | 1P, AC220V | 1P,AC220V | |
| MMA | no-load voltage | 65V | 65V |
| rated output current | 20-200A | 20-250A | |
| duty cycle | 35% | 25% | |
| PLASMACUT | no-load voltage | 248V | 279V |
| rated output current | 10-50A | 10-60A | |
| duty cycle | 40% | 35% | |
| arc starting mode | HF micro start | HF micro start | |
| TIG | no-load voltage | 65V | 65V |
| rated output current | 10-200A | 10-250A | |
| duty cycle | 35% | 40% | |
| up-slope/down-slope time | 0.1-10S | 0.1-10S | |
| pulse currentrange | 10-200A | 10-250A | |
| pulse width range | 10-90% | 10-90% | |
| pulse frequency range | 0.5Hz-50Hz | 0.5Hz-50Hz | |
| arcstartingmode | HF microstart | HF micro start | |
| Degressof enclosure protection | 1P21S | 1P21S | |
| Packge dimensions | 550*345*610mm | 655*380*640mm | |
| Machineweight | 18kg | 22kg | |
Digital Dual Voltage
220V/380V
TIG-315P AC/DC
Digital inverter pulse tigac/dc
| Model | TIG-250P | AG-315P | AG-35OP | TG-40OP | TIG-5CP | TIG-630P | 3H AC-DCUP |
| Rated Input Voltage | AC220V, 1P | 3P, AC380V±10% 50-60Hz | |||||
| Rated input Power | 7.1KVA | 8.6KVA | 10.1KVA | 12.5KVA | 18KVA | 25.8KVA | 41KVA |
| No-load voltage | 60V | 70V±3V | 70V±3V | 70V±3V | 70V±3V | 70V±3V | 70V±3V |
| Current adjusting range 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A | |
| Up-slope time | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s |
| Down-slope time | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s |
| Post flowtime | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s |
| Start arc current | 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A |
| Pulse current | 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A |
| Duty cycle | 60% | 60% | 50% | 60% | 60% | 60% | 60% |
| Effidlency | 83% | 83% | 83% | 33% | 83% | 83% | 83% |
| Pulse frequency | 0.5-100Hz | 0.5-100Hz | 0.5-100Hz | 0.5-100Hz | 0.5100Hz | 0.5-100Hz | 0.5-100Hz |
| Clean width | 2.5%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% |
| AC frequency | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz |
| Degrees of ep | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S |
| Packing size | 550*345*610 655*380*640 730*420*690 730*420*690730*475*840 | 730*475*840 | 850*420*920 | ||||
| Machine weight | 17kg | 25.1kg | 34.2kg | 34.2kg | 53.3kg | 55kg | 76kg |
| Weldable thickness | 0.8-6mm | 1.0-8mm | 1.0-10mm | 1.0-12mm | 1.0-15mm | 1.0-20mm | 1.0-35mm |
Super Power
STRONG PERFORMANCE,STRONG WELDING
TIG-630P AC/DC
Rotaryinverter pulse tigac/dc
| Model | TG-250P | TIG-315P | TIG-35OP | TIG-400P | TG-50OP | TIG-630P | AG-1000P |
| Rated hput Voltage | AC220V, 1P | 3P,AC380V±10%50-60Hz | |||||
| Rated inputPower | 7.1KVA | 8.6KVA | 10.1KVA | 12.5KVA | 18KVA | 25.8KVA | 41KVA |
| No-load vdltage | 60V | 70V±3V | 70V±3V | 70V±3V | 70V±3V | 70V±3V | 70V±3V |
| Current adusting range | 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A |
| Up-slope time | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s |
| Down-slope time | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s | 0.1-5s |
| Post fow time | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s | 5-25s |
| Start arc current | 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A |
| Puse current | 10-250A | 10-315A | 10-350A | 10-400A | 10-500A | 10-630A | 20-1000A |
| Duty cycle | 60% | 60% | 60% | 60% | 60% | 60% | 60% |
| Eficiency | 83% | 83% | 83% | 83% | 83% | 83% | 83% |
| Puse frequency | 0.5-50Hz | 0.5-50Hz | 0.5-50Hz | 0.5-50Hz | 0.5-50Hz | 0.5-50Hz | 0.5-50Hz |
| Clean width | 25%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% | 25%-75% |
| AC frequency | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz | 50-150Hz |
| Degrees ofep | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S |
| Packing size | 550*345*610 | 655*380*640 | 730*420*640 | 730*420*690 | 730*475*840 | 730*475*840 | 850*420*920 |
| Machine weight | 17.7kg | 24.65kg | 34.5kg | 34.5kg | 53.6kg | 55kg | 76.5kg |
| Weldable thickness | 0.8-6mm | 1.0-8mm | 1.0-10mm | 1.0-12mm | 1.0-15mm | 1.0-20mm | 1.0-35mm |
Perfect Power
High Speed Pulse Wire Feeder Inside
MIG-230 PULSE
Digitalinvertermigpulse
| Model | MIG-160P | MIG-230P | MIG-280P | MIG-350P |
| Rated input Voltage | AC220V, 1P | 3P,AC380V±10%50-60Hz | ||
| Rated inputPower | 8.2KVA | 11.8KVA | 14.3KVA | 24KVA |
| No-load voltage | 70V | 64.5V | 70V | 65V |
| Current adjusting range | 10-160A | 10-230A | 10-280A | 30-350A |
| 40C60% duty cycle output | 160A | 230A | 280A | 350A |
| 40C100% duty cycle output | 125A | 178A | 217A | 271A |
| Efficiency (%) | 85 | 85 | 85 | 85 |
| Power factor | 0.93 | 0.93 | 0.93 | 0.93 |
| Degrees of ep | 1P21S | 1P21S | 1P21S | 1P21S |
| Packing size | 545*305*545 | 545*249*445 | 905*445*860 | 905*445*860 |
| Machine weight | 19kg | 27kg | 59kg | 62kg |
| Weldable thickness | 0.5-3mm | 0.5-4mm | 0.8-5mm | 1-10mm |
Super Power
STRONG PERFORMANCE,STRONGWELDING
Digitalinvertermig double pulse
| Model | MIG-280P | MIG-350P | MIG-500P |
| Rated input Voltage | 3P，AC380V±10%50-60Hz | ||
| Rated input Power | 14KVA | 24KVA | 37KVA |
| No-load voltage | 70V | 65V | 65V |
| Current adjusting range | 10-280A | 30-350A | 30-500A |
| 40C60% duty cycle output | 280A | 350A | 500A |
| 40°C100% duty cycle output | 217A | 271A | 387A |
| Efficiency (%) | 85 | 85 | 85 |
| Power factor | 0.93 | 0.93 | 0.93 |
| Degrees of ep | 1P21S | 1P21S | 1P21S |
| Packing size | 905*445*860 | 970*475*925 | 970*475*925 |
| Machine weight | 59kg | 74kg | 76kg |
| Weldable thickness | 0.8-5mm | 5.0-15mm | 5.0-30mm |
Heavy Industry
STRONGPERFORMANCE,STRONG CUTTING
Digital inverter highspeed cutting
| Model | CUT-100 | CUT-120 | CUT-160 | CUT-200 | CUT-300 |
| Rated input Voltage | 3P，AC380V±10% 50-60Hz | ||||
| RatedinputPower | 16.7KVA | 21.3KVA | 32.4KVA | 41.7KVA | 66.7KVA |
| Current adjusting range | 25-100A | 25-120A | 25-160A | 25-200A | 25-300A |
| No-load voltage | 320V | 320V | 341V | 354V | 375V |
| Arc method | Non-contact type | ||||
| Power cooling method | forced air cooling | ||||
| Cooling mode of adjustable gun | air-cool | air-cool | air-cool/water- cooling | ||
| Efficiency | 80% | 80% | 90% | 90% | 90% |
| Cutting thickness(MM) | ≤25 | ≤30 | ≤45 | ≤55 | ≤70 |
| Quality Cutting thickness(MM) | ≤18 | 20 | ≤25 | ≤30 | ≤35 |
| Degrees of ep | 1P21S | 1P21S | 1P21S | 1P21S | 1P21S |
| Packing size | 515*275*470 | 560*305*530 | 680*355*960 | 680*355*960 | 680*355*960 |
| Machine weight | 26.55kg | 32kg | 74kg | 88kg | 93kg |
Heavy Industry
STRONGPERFORMANCE,STRONGWELDING
MMA-1000
| Model | MMA-630 | MMA-1000 | MMA-1250 |
| Rated input Voltage | 3P，AC380V±10%50-60Hz | ||
| Rated inputPower | 39.6KVA | 61KVA | 76KVA |
| No-load voltage | 81V | 81V | 85V |
| Current adjusting range | 30-630A | 30-1000A | 30-1250A |
| Duty cycle | 100% | 100% | 100% |
| Efficiency | 83% | 83% | 83% |
| Carbon-pointDiameter | 4.0-10.0mm | 4.0-12.0mm | 4.0-16.0mm |
| Degrees of ep | 1P21S | 1P21S | 1P21S |
| Packing size | 650*335*575 | 690*365*690 | 690*365*690 |
| Machineweight | 39kg | 69kg | 85kg |
ARC145/160A
■Applicablefield
• Small steel structure, door and window, fencing, manufacturing, furniture manufacturing, electric /bicycle.
■Features
ARC180/200A
Adopting advanced MOS tube Inverter technology, low loss and high output.
•Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement toa greater extent.
•Applicable to reliable welding of variety acid or alkaline welding rod.
·Power grid applicable range (AC187-253V).
• Higher no-load voltage design, easy arc, small splash, stable arc, beautiful shape.
•Adopting high speed fan, fast and all round heat emission, high duty cycle, over-voltage, over-current and overheat protection.
■Applicablefield
Small steel structure, door and window, fencing, manufacturing, furniture manufacturing, electric /bicycle.
■Features
•Adopting advanced MOS tube Inverter technology, low loss and high output.
•Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
•Applicable to reliable welding of variety acid or alkaline welding rod.
·Power grid applicable range (AC187-253V).
• Higher no-load voltage design, easy arc, smallsplash, stable arc, beautiful shape.
•Adopting high speed fan, fast and all round heat emission, high duty cycle, over-voltage, over-current and overheat protection.
■Productparameters
| Product parameters | ARC145 | ARC160 |
| Rating input voltage (V) | AC220V±15% | AC220V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 3.7 | 4.2 |
| Current adjust range | 20-145 | 20-160 |
| 40°C60% duty cycle output | 145 | 160 |
| 40°C100% duty cycle output | 112 | 123 |
| No-load voltage (V) | 60 | 60 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP215 |
| Applicable welding rod diameter (MM) | 2.5-3.2 | 2.5-3.2 |
| Weight (kg) | 6+ | 6+ |
| Dimensions | 350*135*280 | 350*135*280 |
■ARC-160Aweldingmachinerecommend
| Welding material | Welding method | Max. Current |
| Carbon steel/ Low alloy steel/ | DC ARC | 160A |
| Product parameters | ARC180 | ARC200 |
| Rating input voltage (V) | AC220V±15% | AC220V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 4.9 | 5.6 |
| Current adjust range | 20-180 | 20-200 |
| 40°C60% duty cycle output | 180 | 200 |
| 40C100% duty cycle output | 138 | 154 |
| No-load voltage (V) | 60 | 60 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP215 | IP215 |
| Applicable welding rod diameter (MM) | 2.5-3.2 | 2.5-3.2 |
| Weight (kg) | 6.5+ | 6.5+ |
| Dimensions | 350*135*280 | 350*135*280 |
■Welding process
Carbon steel horizontal fillet welding
Welding current: 145/160A Welding rod diameter: φ2.5/3.2 Sheet type: 5/6mm carbon steel sheet
| Welding material | Welding method | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ | DC ARC | 200A |
| Stainless steel |
■ARC-2ooAweldingmachine recommend
■Welding process
Carbonsteel horizontal fillet welding
Welding current: 145/160A Welding rod diameter: φ2.5/3.2 Sheet type: 5/6mm carbon steel sheet
ARC125/145/160A
■Applicable field
•Small steel structure, door and window, fencing manufacturing.
furniture manufacturing, electric /bicycle.
■Features
•Adopting advanced IGBT Inverter technology, low loss and high output.
•Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greaterextent.
•Applicable to reliable welding of variety acid or alkaline welding rod.
Power grid applicable range (AC187-253V).
·Higher no-load voltage design, easy arc, smal splash, stable arc, beautiful shape.
•Adopting high speed fan,fast and all round heat emission, high duty cycle, over-voltage,over-current and overheat protection.
ARC200/250A
■Applicablefield
• Small steel structure, door and window, fencing, manufacturing, furniture manufacturing, electric /bicycle.
■Features
•Adopting advanced IGBT Inverter technology, low loss and high output.
Advanced digital control program, improve dramatically the reliability of the welding machine,and meet welding process requirement to a greater extent.
•Applicable_to reliablewelding of variety acid oralkaline welding rod.
Adoptingtoawiderang(AC323-437Vpowergrid,strong grid adaptability,Continuedhigh_loadcapacity,suitable for long time continuous operation offactory.
Higher no-load voltage design, easy arc, small splash, stable arc, beautiful shape.
•Adopting high speed fan, fast and all round heat emission, high duty cycle, over-voltage, over-current and overheat protection.
■Productparameters
| Product parameters | ARC125/ARC145/ARC160 |
| Rating input voltage (V) | AC220V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 3.1/3.7/4.2 |
| Current adjust range | 20-125/20-145/20-160 |
| 40C60% duty cycle output | 125/145/160 |
| 40C100% duty cycle output | 96/112/123 |
| No-load voltage (V) | 60 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Applicable welding rod diameter (MM) | 2.5-3.2 |
| Weight (kg) | 6+ |
| Dimensions | 350*135*280 |
Electrode holder with 3M cable
Earth clamp with 3M cable
Electrode holder with 3M cable
Earth clamp with 3M cable
■ARC-160Aweldingmachinerecommend
■ARC-250Aweldingmachinerecommend
| Product parameters | ARC200 | ARC250 |
| Rating input voltage (V) | AC220V±15% | AC220V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 5.6 | 7.5 |
| Current adjust range | 20-200 | 20-250 |
| 40C60% duty cydle output | 200 | 250 |
| 40°C100% duty cycle output | 154 | 193 |
| No-load voltage (V) | 60 | 60 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP215 | IP21S |
| Applicable welding rod diameter (MM) | 2.5-3.2 | 2.5-3.2 |
| Weight (kg) | 7.5+ | 7.5+ |
| Dimensions | 350*135*280 | 350*135*280 |
| Welding material | Welding method | Max. Current |
| Carbon steel/ Low alloy steel/ | DC ARC | 160A |
| Welding material | Welding method | Max. Current |
| Carbon steel/ | DC ARC | 250A |
| Low alloy steel/ Stainless steel |
■Welding process
Carbon steel horizontal fillet welding
Welding current: 145/160A Welding rod diameter: φ2.5/3.2 Sheet type: 5/6mm carbon steel sheet
■Welding process
Carbon steel horizontal fillet welding
Welding current: 145/160A Welding rod diameter: φ2.5/3.2 Sheet type: 5/6mm carbon steel sheet
ARC315/400A
ARC400/500/630A
■Applicablefield
• Small steel structure, door and window, fencing, manufacturing furniture manufacturing, electric /bicycle
■Features
•Adopting advanced IGBT Inverter technology, low loss and high output.
Advanced digital control program,improve dramatically the reliability of the weldingmachine,and meet welding process requirement to a greater extent.
·Applicabletoreliableweldingof varietyacid oralkaline welding rod.
Adoptingtoawiderang (AC323-437V)power grid,strong gridadaptability,Continued high load capacity,suitable for long time continuous operation of factory.
•Higher no-load voltage design, easy arc, smallsplash, stable arc, beautiful shape.
·Adopting high speed fan,fast and all round heat emission, high duty cycle, over-voltage, over-current and overheat protection.
■Applicable field
Smallstel structure, door and window, fencing, manufacturing furniture manufacturing, electric /bicycle.
■Features
Adopting advanced IGBT MODULE Inverter technology, low loss and high output.
Advanced digital control program, improve dramatically the reliability of the welding machine,and meet welding process requirement to a greater extent.
•Applicable_to reliablewelding of varietyacid oralkaline welding rod.
Adopting toa widerang (AC323-437V）power grid,strong grid adaptability,Continued high load capacity,suitable for long time continuous operation of factory.
Higher no-load voltage design,easy arc, small splash,stable arc, beautiful shape.
•Adopting high speed fan, fast and all round heat emission, high duty cycle, over-voltage, over-current and overheat protection.
■Productparameters
| Product parameters | ARC315 | ARC400 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 10.3 | 14.4 |
| Current adjust range | 20-315 | 30-400 |
| 40°C60% duty cycle output | 315 | 400 |
| 40℃100% duty cycle output | 243 | 308 |
| No-load voltage (V) | 60 | 60 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP215 |
| Applicable welding rod diameter (MM) | 2.5-5.0 | 2.5-5.0 |
| Weight (kg) | 20+ | 20+ |
| Dimensions | 480*205*370 | 480*205*370 |
Electrode holder with 3M cable
Earth clamp with 3M cable
Electrode holder with 3M cable
| Product parameters | ARC500 | ARC630 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 20 | 28.5 |
| Current adjust range | 20-500 | 30-630 |
| 40°C60% duty cycle output | 500 | 630 |
| 40°C100% duty cycle output | 385 | 485 |
| No-load voltage (V) | 70 | 70 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP21S |
| Applicable welding rod diameter (MM) | 2.5-5.0 | 2.5-8.0 |
| Weight (kg) | 39+ | 39+ |
| Dimensions | 600*265*470 | 600*265*470 |
Earth clamp with 3M cable
■ARC-40oAweldingmachinerecommend
■ARC-630Aweldingmachinerecommend
| Welding material | Welding method | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | DC ARC | 400A |
| Welding material | Welding method | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ | DC ARC | 630A |
| Stainless steel |
■Welding process
Carbon steel horizontal fillet welding
Welding current: 180/230A Welding rod diameter: φ3.2/4.0 Sheet type: 8/10mm carbon steel sheet
■Welding process
Carbon steel horizontal fillet welding
Welding current: 230/300A Welding rod diameter: φ4.0/5.0 Sheet type: 10/16mm carbon steel sheet
CUT40A
CUT60/80A
■Applicable field
• Hardware manufacture,construction and decorating installation,sheet metal factory,
■Features
Adoptingadvanced MOstube inverter technology,compact size,low consumption and high output.
Adopting PwM control program,improve dramatically the reliabilityof thewelding machine,andmeetwelding process requirementtoagreater extent.
Advanced digital control program,improve dramatically the reliability of the_weldingmachine,andmeetwelding process requirement toa greater extent.
Exclusive designquick responsearcing successate 100%.
With2T/4T function,easy toweld,high welding efficiency.
High cutting speed,narrow cut,vertical andsmooth cut,less slagging.
Power gridapplicablerange(AC187-253V),high power grid adaptability,sustainedhigh load,suitablefor longtimecontinuous factorywork.
•Equipped with international famous brand torch, consumable life is two times more than the ordinary brand.
●Fast and allround heat emission by adopting three-proof air duct, high duty cycle,over-voltage,over-current and overheat protection.
■Applicable field
• Shipbuilding, miner machinery, construction and decorating installation, sheet metal factory.
■Features
Adopting advanced IGBT inverter technology, compact, low loss and high output.
·Advanced digital control program,improve dramatically the reliability of the welding machine, and meet welding process requirement toagreaterextent.
Exclusive design,quick response,arcing successrate 100%.
With 2T/4T function,easy to weld,high welding efficiency.
High cutting speedrowuteticalandsmoothct,less slagging.
Power grid applicablerange(AC323-437V).highpower grid adaptabilitysustainedhigh load,suitable for long time continuous factory work.
Equipped with international famousbrand torch, consumable life is two times more than the ordinary brand.
Fastandall round heat emission byadopting three-proof air duct,high duty cycle,over-voltage,over-current and overheat protection.
■Productparameters
| Product parameters | CUT60 | CUT80 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 7.8 | 9 |
| Current adjust range | 20·60 | 20-80 |
| 40℃60% duty cycle output | 60 | 80 |
| 40℃100% duty cycle output | 47 | 62 |
| No-load voltage (V) | 292 | 292 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP215 | IP215 |
| Cutting thickness(MM) | 1-15 | 1-18 |
| Quality cutting thickness(MM) | 1-10 | 1-12 |
| Working gas pressure(mpa) | 0.35-0.55 | 0.35-0.55 |
| Weight (kg) | 16.5+ | 16.5+ |
| Dimensions | 480*205*370 | 480*205*370 |
| Product parameters | CUT40 |
| Rating input voltage (V) | AC220V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 4.5 |
| Current adjust range | 20-40 |
| 40C60% duty cycle output | 40 |
| 40℃100% duty cycle output | 31 |
| No-load voltage (V) | 255 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Cutting thickness(MM) | 1-12 |
| Quality cutting thickness(MM) | 1-6 |
| Working gas pressure(mpa) | 0.35-0.5 |
| Weight (kg) | 8.5 |
| Dimensions | 380*170*305 |
| Welding material | Arcing way | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | Contact type | 40A |
| Welding material | Arcing way | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | Non-contact type | 80A |
■Welding process
■Welding process
Cutting effect
Cutting current: 30/40A Sheet type: 2/4mm aluminum sheet Gas pressure: 0.2/0.3
Cutting effect
Cutting current: 60/80A
Sheet type: 12/16mm carbon steel sheet
Gas pressure: 0.4/0.5
CUT100/120A
■Applicable field
•Shipbuilding, miner machinery, construction and decorating installation, sheet metal factory.
■Features
●Adopting advanced IGBT MODULE inverter technology, compact, lowloss and high output
New dimension arc circuit technology, no interference,quick response,arcing success rate 100%.
Advanced digital control program,improve dramatically the reliability of the weldingmachine,andmeet weldingprocess requirementtoa greaterextent.
Exclusive design,quick response,arcing success rate 100%.
With 2T/4T function,easy to weld,high welding efficiency.
•High cutting speed,narrow cut,vertical and smooth cut,less slagging.
Powergridapplicablerange(AC323-437V,high power grid adaptability,sustained high load,suitable for long time continuous factory work.
●Equipped with international famous brand torch, consumable life is two timesmore than the ordinary brand.
Fastand all round heat emission by adopting three-proof air duct, high duty cycle, over-voltage,over-current and overheat protection.
■Productparameters
品 SEJIC
■Applicablefield
• Shipbuilding, miner machinery, construction and decorating installation, sheet metal factory.
CUT160/200A
■Features
Adopting advanced IGBT MODULE inverter technology, compact, low lossand high output.
·New dimension arc circuit technology,no interference,quick response, arcing success rate 100%.
Heavy industry cuttingequipmentequipped witharc voltage detection output,perfectly compatible with CNC.
Advanced digital control program,improve dramatically the reliabilityof theweldingmachine,and meet welding process requirement to a greater extent.
Exclusive designquick response,arcing success rate 100%.
With2/4Tuctioneasytoweldigheingy
High cuting speed,narrow cutvertical and smooth cut,less slagging.
Powergridapplicablerange(AC323-437V),highpower grid adaptability,sustained high load,suitable for long time continuous factory work.
Equipped with international famous brand torch, consumable life is two times more than the ordinary brand.
Fastandallroundheatemissionbyadoptingtheeprofairduct high duty cycle, over-voltage,over-current and overheat protection.
Productparameters
a ○ P-80/90 cutting torch Ground clip Reducing Valve
? A141 cutting torch Ground clip Reducing Valve
| Product parameters | CUT100 | CUT120 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 12.0 | 15.4 |
| Current adjust range | 30-100 | 30-120 |
| 40°C60% duty cycle output | 100 | 120 |
| 40℃C100% duty cycle output | 77 | 92 |
| No-load voltage (V) | 282 | 282 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP215 |
| Cutting thickness(MM) | 1-35 | 1-40 |
| Quality cutting thickness(MM) | 1-18 | 1-25 |
| Working gas pressure(mpa) | 0.4-0.6 | 0.4-0.6 |
| Weight (kg) | 35+ | 35+ |
| Dimensions | 600*265*470 | 600*265*470 |
| Welding material | Arcing way | Max. Current |
| Carbon steel/ Low alloy steel/ | Non-contact type | 120A |
| Productparameters | CUT160 | CUT200 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 23.0 | 32.0 |
| Current adjust range | 30-160 | 30-200 |
| 40°C60% duty cycle output | 160 | 200 |
| 40C100% duty cycle output | 123 | 154 |
| No-load voltage (V) | 338 | 338 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP21S |
| Cutting thickness(MM) | 1-55 | 1-60 |
| Quality cutting thickness(MM) | 1-30 | 1-30 |
| Working gas pressure(mpa) | 0.4-0.6 | 0.4-0.6 |
| Weight (kg) | 50+ | 50+ |
| Dimensions | 765*460*675 | 765*460*675 |
| Welding material | Arcing way | Max. Current |
| Carbon steel/ Low alloy steel/ | Non-contact type | 200A |
■Welding process
■Welding process
Cutting effect
Cutting current: 100/120A Sheet type: 25/30mm carbon steel sheet Gas pressure: 0.5/0.6
Cutting effect
Cutting current: 160/200A Sheet type: 40/60mm carbon steel sheet Gas pressure: 0.7/0.8
MIG160/180/200/220A
■Applicable field
• Containers,smallsteel structure, door and window, fencing, manufacturing, furniture manufacturing, electric/bicycle.
■Features
Adopting advanced IGBT Inverter technology, low loss and high output.
•Dual-use of CO2 MIG welding and hand welding.
36V heater power supply.
•Better control of short circuit transition waveform, stable welding, small spatter.
Power grid applicable range (AC187-253v), high power grid adaptability,sustained high load,suitableforlongtime continuous factory work.
Unusual intelligent design with various function of overvoltage, over-current and overheat protection.
Adopt high no-load voltage design containing the function of reducing the ball with arc, so as to ensure the stability of the welding.
MIG250/300G
■Applicable field
•Containers,small steel structure, door and window, fencing, manufacturing, fumiture manufacturing, electric/bicycle.
■Features
| Product parameters | MIG160/180/200/220 |
| Rating input voltage (V) | AC220V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 3.5/4.1/4.8/5.5 |
| Current adjust range | 20-160/20-220/20-220/20-220 |
| 40°C60% duty cycle output | 160/180/200/220 |
| 40'C100% duty cycle output | 123/139/154/169 |
| No-load voltage (V) | 50 |
| Efficiency (%) | 85 |
| Power factor | 0.73/0.73/0.93/0.93 |
| Insulation class | F |
| Housing protection class | IP215 |
| welding thickness(MM) | 0.8+ |
| Weight (kg) | 15+ |
| Dimensions | 380*170*305 |
●Adopting advanced IGBT Inverter technology, low Ioss and high output.
Dual-use of CO2 MIG welding and hand welding.
Advanced digital control program,improve dramaticallythe reliability of the weldingmachine,and meet welding process requirement to a greater extent.
36V gas heater power supply.
●Better control of short circuit transition waveform, stable welding, small spatter.
Powergridapplicablerange(AC323-437V).highpower grid adaptability, sustained high load, suitable for long time continuous factory work.
Soft or hard adjustment of inductance,deep molten pool, small spatter,even weld line and perfect appearance.
●Unusual intelligent design with various function of over-voltage, over-current and overheat protection.
Adopt high no-load voltage design containing the function of reducing the ball with arc, so as to ensure the stability of the welding.
® cob ® sob 3M Euro connector Earth clamp 3M gas 4 pcs hose MIG torch with 3M cable hose clamp
| Product parameters | MIG250 | MIG300 |
| Rating input voltage (V) | AC220V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | SOHZ |
| Rating input power (KVA) | 6.6 | 19.5 |
| Current adjust range | 20-250 | 40-500 |
| 40°C60% duty cycle output | 250 | 500 |
| 40℃100% duty cycle output | 193 | 385 |
| No-load voltage (V) | 50 | 50 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP215 |
| welding thickness(MM) | 0.8-10 | 0.8-16 |
| Weight (kg) | 20+ | 20+ |
| Dimensions | 500*275*485 | 500*275*485 |
3M Euro connector Earth clamp 3M gas 4 pcs hose MIG torch with 3M cable hose clamp
■MIG-2ooAweldingmachinerecommend
■MIG-3ooAweldingmachinerecommend
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ Low alloy steel/ | 0.8/1.0/1.2 | 200A |
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | 0.8/1.0/1.2 | 300A |
■Weldingprocess
Welding performance
Wire model: 1.0
Welding current: 120A
Welding voltage: 20.5V
CO2 Gas flow: 10-11L/min
Sheet type: 5/10mm carbon steel sheet
■Welding process
Welding performance
Wire model: 1.0
Welding current: 160A
Welding voltage:23V
CO2 Gas flow: 10-11L/min
Sheet type: 5/10mm carbon steel sheet
MIG300/350/500A
■Applicable field
•Containers,smallsteel structure, door and window, fencing manufacturing, furmiture manufacturing, electric/bicycle.
■Features
Adopting advanced IGBT MODULE Inverter technology, low loss and high output.
Dual-use of CO2 MlG welding and hand welding.
Advanced digital control program,improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
36V gas heater power supply.
•With 2T/4T function,easy to weld,high welding efficiency.
Bettercontrol of short circuit transitionwaveform,stable welding,small spatter.
Power grid applicable range (AC323-437V), high power grid adaptability，sustainedhigh load,suitablefor long time continuous factory work.
Soft or hard adjustment of inductance,deep molten pool, small spatter,evenweld line and perfect appearance.
Unusual intelligent designwithvarious functionofovervoltage, over-current and overheat protection.
Adopt high no-load voltage designcontainingthefunction of reducing the ball with arc, so as to ensure the stability of the welding.
MIG350/500/630l
■Applicable field
·Containers,smallsteel structure, door and window, fencing manufacturing, furniture manufacturing, electric/bicycle.
■Features
Adopting advanced IGBT MODULE Inverter technology, low lossand high output.
Dual-use of CO2 MIG welding and hand welding.
Advanced digital control program,improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
36V gas heater power supply.
With2T/4Tfunction,easytoweld,high welding efficiency
Better control of short circuit transition waveform,stable welding, small spatter.
Power grid applicable range (AC323-437V),high power grid adaptability，sustainedhighload,suitablefor longtime continuous factory work.
Soft or hard adjustment of inductance,deep molten pool, small spatter, even weld line and perfect appearance.
Unusual intelligentdesignwithvarious function ofovervoltage, over-current and overheat protection.
Adopt high no-load voltage designcontaining thefunction of reducing the ball with arc, so as to ensure the stability of the welding.
| Productparameters | MIG300/350/500 |
| Rating input voltage (V) | AC380V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 8.7/11.0/19.5 |
| Current adjust range | 20-300/20-350/40-500 |
| 40℃C60% duty cycle output | 300/350/500 |
| 40°C100% duty cycle output | 231/270/385 |
| No-load voltage (V) | 50 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Welding thickness(MM) | 0.8-16 |
| Weight (kg) | 25+ |
| Dimensions | 600*265*470 |
b0b Wire Feeder KR350 gas Gas meter Ground clip shielded welding gun
| Productparameters | MIG 350/500/6301 |
| Rating input voltage (V) | AC380V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 11.0/19.5/28.7 |
| Current adjust range | 20-350/20-500/20-630 |
| 40°C60% duty cycle output | 350/500/630 |
| 40℃100% duty cycle output | 270/385/485 |
| No-load voltage (V) | 50 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Welding thickness(MM) | 0.8-16 |
| Weight (kg) | 40+ |
| Dimensions | 745*410*710 |
bob Wire Feeder KR350 gas Gas meter Ground clip shielded welding gun
■MIG-350Aweldingmachinerecommend
■MIG-5oolweldingmachinerecommend
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ Low alloy steel/ | 0.8/1.0/1.2/1.6 | 350 |
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | 0.8/1.0/1.2/1.6 | 500 |
■Welding process
Welding performance
Wire model: 1.2/1.6
Welding current: 120/160A
Welding voltage: 23V
CO2 Gas flow: 10-11L/min
Sheet type: 8/15mm carbon steel sheet
■Welding process
Welding performance
Wire model: 1.2/1.6
Welding current: 350/500A
Welding voltage:23V
CO2 Gas flow: 10-11L/min
Sheet type: 8/15mm carbon steel sheet
NBM270YS
■Applicable field
·Containers,smallsteel structure, door and window, fencing manufacturing, furniture manufacturing, electric/bicycle.
■Features
Adopting advanced IGBT MODULE Inverter technology, low lossand highoutput.
Dual-use of CO2 MiG welding and hand welding.
Advanceddigital singlepulse control programimprove dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
36V gas heater power supply.
With2T/4Tfunction,easyto weld,highweldingefficiency
•Better control of short circuit transition waveform, stable welding,small spatter.
Power grid applicable range (AC187-253v), high power grid adaptability，sustainedhigh load,suitable forlongtime continuous factory work.
Soft or hard adjustment of inductance,deep molten pool, small spatter, even weld line and perfect appearance.
Unusual intellgent designwith variousfunctionof over voltage, over-current and overheat protection.
Adopt high no-load voltage designcontainingthefunction of reducing the ball with arc, so as to ensure the stability of the welding.
NBM3501/500l
■Applicable field
·Containers,smallsteel structure, door and window, fencing, manufacturing, furmiture manufacturing, electric/bicycle.
■Features
Adopting advanced IGBT MODULE Inverter technology, low lossand high output.
Dual-use of CO2 MiG welding and hand welding.
Advanced digital doublepulse controlprogram,improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
36V gas heater power supply.
With2T/4Tfunction,easyto weld,high welding efficiency
•Better control of short circuit transitionwaveform,stable welding,small spatter.
Power grid applicable range (AC323-437V), high power grid adaptability,sustained high load, suitable for long time continuous factory work.
Soft or hard adjustment of inductance,deep moltenpool, small spatter, even weld line and perfect appearance.
Unusual intellgent designwith variousfunctionof overvoltage, over-current and overheat protection.
Adopt high no-load voltage designcontaining the function of reducing the ball with arc, so as to ensure the stability of the welding.
| Product parameters | NBM270YS |
| Input Voltage(V) | AC220V±15% |
| Frequency(HZ) | 50HZ |
| Rated Input power(A) | 7.4 |
| Current adjust range | 30-270 |
| 40C60% duty cycle output | 270 |
| 40C100% duty cycle output | 208 |
| No-load voltage (V) | 50 |
| Efficiency (%) | 85 |
| Power factor | 0.73 |
| Insulation class | F |
| Housing protection class | IP215 |
| Applicable welding rod diameter (MM) | 0.8-10 |
| Weight (kg) | 16 |
| Dimensions | 500*275*485 |
® bob 3M Euro connector Earth clamp 3M gas 4 pcs hose MIG torch with 3M cable hose clamp
100
Wire Feeder KR350gas Gasmeter Ground clip
shielded
welding gun
| Product parameters | NBM3501 | NBM5001 |
| Rating input voltage (V) | AC380V±15% | AC380V±15% |
| Input frequency (HZ) | 50HZ | 50HZ |
| Rating input power (KVA) | 11.0 | 19.5 |
| Current adjust range | 40-350 | 40-500 |
| 40℃C60% durty cycle output | 350 | 500 |
| 40℃C100% duty cycle output | 270 | 385 |
| No-load voltage (V) | 50 | 50 |
| Efficiency (%) | 85 | 85 |
| Power factor | 0.93 | 0.93 |
| Insulation class | F | F |
| Housing protection class | IP21S | IP21S |
| Welding thickness(MM) | 0.8-10 | 0.8-16 |
| Weight (kg) | 34.5 | 46 |
| Dimensions | 600*265*470 | 600*265*470 |
■NBM270YSweldingmachine recommend
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ Low alloy steel/ Stainless steel | 0.8/1.0/1.2/1.6 | 270 |
■NBM5oolweldingmachinerecommend
| Welding material | Wire diameter(mm) Max. Current | |
| Carbon steel/ | ||
| Low alloy steel/ | 0.8/1.0/1.2/1.6 | 500 |
| Stainless steel |
■Welding process
Welding performance
Wire model:1.2/1.6
Welding current:120/160A
Welding voltage:23V
CO2 Gas flow:10-11L/min
Sheet type: 8/15mm carbon steel sheet
■Welding process
Welding performance
Wire model:1.2/1.6
Welding current:120/160A
Welding voltage:23V
CO2 Gas flow:10-11L/min
Sheet type: 8/15mm carbon steel sheet
RSR1600
■Applicable field
• Distribution boxes, kitchen utensils, billboards, metal manufacturing industry.
■Features
·Adopting constant current photoelectric control technology, strong ability to resist power grid fluctuation, mature and high reliability.
●High efficient capacitor that durable for 3ooooooo times of operation.
• Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement toa greater extent.
Exclusive technology，standalone control mode and drive protectioncircuit,highefficiency，energysaving,easyto operate.
Imported high-power SCR devices, stable performance.
Perfect over-voltage,over-current,welding voltage preset display.
•Perfect welding for steel,stainless steel,aluminum, aluminum alloy, and other metal materials. EESPE RSR-1600 SEJIC
Standardaccessories
3 OO
Positioning rod stud Ground clip welding torch
■Productparameters
■RSR-16o0weldingmachinerecommend
| Product parameters | RSR1600 |
| Rating input voltage (V) | AC220V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 0.45 |
| Recharge voltage (V) | 20-200 |
| Capacitance capacity (UF) | 72000 |
| Storage energy (J) | 1600 |
| Load succession rate (X) | 100% |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Iinsulation class | F |
| Housing protection class | IP215 |
| Weight (kg) | 22 |
| Dimensions | 480*205*370 |
| weldling | Welding | Welingnall | (pmin) |
| Copper/ Carbon steel/ Aluminum/ Aluminum alloy/ Stainless steel | 20-200 | 3-8 | 10 |
■Welding process
Welding performance
Welding voltage: 110/130V Sheet type: 2mm Aluminum sheet Welding nail diameter: M6
RSR 2500
■Applicablefield
• Distribution boxes, kitchen utensils, billboards, metal manufacturing industry.
Features
Adopting constant current photoelectric control technology, strong ability to resist power grid fluctuation, mature and high reliability.
• High efficient capacitor that durable for 3ooooo00 times of operation.
• Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
·Exclusive technology,standalone control mode and drive protectioncircuit,highefficiency,energysaving,easy to operate.
Imported high-power SCR devices, stable performance.
Perfect over-voltage, over-current,welding voltage preset displlay.
•Perfect welding for steel,stainless steel,aluminum, aluminum alloy, and other metal materials.
tssere RSR-2500 SEJiC ■Standardaccessories 3 OO Positioning rod stud Ground clip welding torch
■Productparameters
| Productparameters | RSR2500 |
| Rating input voltage (V) | AC220V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 0.45 |
| Recharge voltage (V) | 20-200 |
| Capacitance capacity (UF) | 108000 |
| Storage energy (J) | 2500 |
| Load succession rate (X) | 100% |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Weight (kg) | 24 |
| Dimensions | 480*205*370 |
■RSR-25o0weldingmachinerecommend
| weling | Weling | Weldling nal | |
| Copper/ Aaubonsteel/ Aluminum alloy/ | 20-200 | 3-10 | 10 |
■Welding process
Welding performance
Welding voltage: 110/130V Sheet type: 3mm Aluminum sheet Welding nail diameter: M8
HTl
TIG160/200/250/300S
■Applicable field
• Hardware manufacture, construction and decorating installation sheet metal factory, chemical pipeline maintenance.
■Features
Adopting advanced MOS tube Inverter technology, compact, low loss and high output.
• Adopting the design of high-frequency boost arc and pulse thermal arc, arcing success rate 100%.
•Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
·Welding current sufficient, excellent cost performance.
Powergrid applicablerange (AC187-253V), highpower grid adaptability，sustainedhighload,suitableforlongtime continuous factory work.
Higher no-load voltagedesign,easy arc,small splash,stable arc, beautiful shape.
·Fast and all round heat emission by adopting high speed fan, high duty cycle, over-voltage, over-current and overheat protection.
TIG200/250/300
■Applicable field
•Hardware manufacture, construction and decorating installation, sheet metal factory, chemical pipeline maintenance.
■Features
●Adopting advanced IGBT Inverter technology, compact, low loss and high output.
Adopting the design of high-frequency boost arc and pulse thermal arc,arcing success rate 100%.
Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
·Welding current sufficient, excellent cost performance.
•Dual functions of TIG and ARC welding.
•With 2T/4T function, easy to weld, high welding efficiency.
Power grid applicable range (AC323-437V),high power grid adaptability, sustained high load, suitable for long time continuous factory work.
• Higher no-load voltage design, easy arc, smallsplash, stable arc, beautiful shape.
·Fast and all round heat emission by adopting high speed fan, high duty cycle, over-voltage, over-current and overheat protection.
O O QQ150 Torch Ground clip
| Product parameters | TIG 160/200/250/3005 |
| Rating input voltage (V) | Ac220±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 2.6/3.6/5.0/6.6 |
| Current adjust range | 20-160/20-200/20-250/20-300 |
| 40'C60% duty cycle output | 160/200/250/300 |
| 40C100% duty cycle output | 123/154/193/231 |
| No-load voltage (V) | 60 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Weight (kg) | 7.5+ |
| Dimensions | 380*155*305/480*205*370 |
■TIG-200 weldingmachine recommend
| Welding material | Welding method | Max.Current |
| Carbon steel/ Low alloy steel/ Stainless steel | DC TIG | 200A |
| Product parameters | TIG200/250/300 |
| Rating input voltage (V) | AC380V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 3.6/5.0/6.6 |
| Current adjust range | 10-200/10-250/10-300 |
| 40°C60% duty cycle output | 200/250/300 |
| 40°C100% duty cycle output | 154/193/231 |
| No-load voltage (V) | 60 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP215 |
| Weight (kg) | 8+ |
| Dimensions | 380*170*305/480*205*370 |
4M TIG torch WP-17/ Electrode holder Earth clamp with WP-26/WP-18 with 3M cable 3M cable
■TIG-3ooAweldingmachinerecommend
| Welding material | Welding method | Max. Current |
| Carbon steel/ Low alloy steel/ Stainless steel | DC TIG | 300A |
■Welding process
■Welding process
Stainless steel argon arc welding
Welding current: 100/120A
Tungsten diameter: φ1.6/2.4mm
Sheet type: 2/2.5mm stainless steel sheet
Wire diameter: φ2.0mm
Gas flow: 9-10L/min
Stainless steel argon arc welding
Welding current: 100/120A
Tungsten diameter: φ1.6/2.4mm
Sheet type: 2/2.5mmstainless steel sheet
Wire diameter: φ2.0mm
Gas flow: 9-10L/min
TIG4001/5001
■Applicablefield
•Hardware manufacture, construction and decorating installation, sheet metal factory, chemical pipeline maintenance.
Features
Adoptingadvanced IGBT MODULE Inverter technology,
compact, low loss and high output.
Adopting the design of high-frequency boost arc and pulse thermal arc,arcing success rate 100%
Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
·Welding current sufficient, excellent cost performance.
Dual functions of TIG and ARC welding.
•With 2T/4T function,easy to weld, high welding eficiency.
Power grid applicable range (AC323-437V), high power grid adaptability,sustained high load,suitable for long time continuous factory work.
• Higher no-load voltage design, easy arc, small splash, stable arc, beautiful shape.
•Fast and all round heat emission by adopting high speed fan, high duty cycle, over-voltage, over-current and overheat protection.
■Productparameters
4M TIG torch WP-17/ Electrode holder Earth clamp with WP-26/WP-18 with 3M cable 3M cable
■TIG-40ol weldingmachinerecommend
| Product parameters | TIG4001/5001 |
| Rating input voltage (V) | AC380V±15% |
| Input frequency (HZ) | 50HZ |
| Rating input power (KVA) | 10.4/15.0 |
| Current adjust range | 30-400/30-500 |
| 40°C60% duty cycle output | 400/500 |
| 40℃100% duty cycle output | 308/385 |
| No-load voltage (V) | 64 |
| Efficiency (%) | 85 |
| Power factor | 0.93 |
| Insulation class | F |
| Housing protection class | IP21S |
| Weight (kg) | 20+ |
| Dimensions | 600*265*470 |
| Welding material | Welding method | Max. Current |
| Carbon steel/ | ||
| Low alloy steel/ Stainless steel | DC TIG | 400A |
■Weldingprocess
Stainless steel argon arc welding
Welding current: 100/120A
Tungsten diameter: 𝜑1.6/2.4mm
Sheet type: 4/6mm stainlesssteel sheet
Wire diameter: φ2.0mm
Gas flow: 9-10L/min
TIG200/250PAC/DC
■Applicable field
•Hardware manufacture, construction and decorating installation, sheet metal factory, chemical pipeline maintenance.
IFeatures
Adopting advanced MOS tube Invertedlnverter technology, compact,low loss and high output.
·Adopting the design of high-frequency boost arc and pulse thermal arc,arcing success rate 100%.
Advanced digital control program, improve dramatically the reliability of the welding machine, and meet welding process requirement to a greater extent.
Welding current suficient,excellent cost performance.
Dualfunctionsof TIGand ARCwelding.
Adoptingadvanced AC/DCPULSE technology.
With2T/4Tfunctioneasytoweld,high weldingeficiency.
Power grid applicable range (AC323-437V),high power grid adaptability,sustained high load,suitable for longtime continuous factory work.
·Higher no-load voltage design, easy arc, small splash, stable arc, beautiful shape.
Fast andall round heat emission by adopting high speed fan, high duty cycle, over-voltage, over-current and overheat protection.
■Productparameters
4M TIG torch WP-17/ Electrode holder Earth clamp with WP-26/WP-18 with 3M cable 3M cable
■Product Purchase Guide
| Welding material | Plate thickness(mm) | Welding process | Current range(A) |
| 0.8-3.0/4.0/16.0 | DC TIG | 10-2005 |
| Productparameters | TIG200PAC/DC|TIG250PAC/DC | |
| Input Voltage(V) | AC220V±15% | AC220V±15% |
| Frequency(HZ) | 50 | 50 |
| Rated Input Current(A) | 32.5 | 43.5 |
| Output Current Range(A) | 10-200 | 10-250 |
| No-load Voltage(V) | 44 | 44 |
| Rated Output Voltage(V) | 18 | 20 |
| Pre-flow(S) | 0-2 | 0-2 |
| Vale value current(%) | 20-80 | 20-80 |
| Down slope(S) | 0-10 | 0-10 |
| Post-flow(S) | 2-10 | 2-10 |
| Remote Control | YES | YES |
| Arcing Way | Transfer | Transfer |
| Efficiency(%) | 80 | 80 |
| Duty Cycle(%) | 60 | 60 |
| Power Factor | 0.73 | 0.73 |
| Insulation Grade | F | F |
| Housing Protection Grade | IP215 | IP21S |
| Net Weight(kg) | 20 | 20.5 |
| Packing Dimension(mm) | 605*445*425 | 605*445*425 |
■Weldingprocess
Stainless steel argon arc welding
Welding current: 100/120A
Tungsten diameter: φ1.6/2.4mm
Sheet type: 2/2.5mm stainless steel sheet
Wire diameter: φ2.0mm
Gas flow: 9-10L/min
TIG315P/315BPAC/DC
•Hardware manufacture, construction and decorating installation sheet metal factory, chemical pipeline maintenance.
■Features
■Applicable field
Adopting advanced MOs tube Inverter technology, compact, low loss and high output.
•Adopting the design of high-frequency boost arc and pulse thermal arc,arcing success rate 100%.
Advanced digital control program,improve dramatically the reliability of the welding machine,and meet welding process requirement to a greater extent.
Welding current sufficient, excellent cost performance.
Dual functions of TIGand ARC welding.
Adopting advanced AC/ DC PULSE technology.
•With 2T/4T function,easy to weld, high welding efficiency.
With remotecontrol interface,remote pedal switch control.
Power grid applicablerange(AC187-253V).highpower grid adaptability,sustained high load,suitable forlong time continuous factory work.
•Higher no-load voltage design, easy arc, small splash, stable arc,beautiful shape.
•Fast and all round heat emission by adopting high speed fan, highduty cycle, over-voltage,over-current and overheat protection.
■Productparameters
4M TIG torch WP-17/ Electrode holder Earth clamp with WP-26/WP-18 with 3M cable 3M cable
| Productparameters | TIG315PAC/DCTIG315BPAC/DC | |
| Input Voltage(V) | AC380V±15% | AC380V±15% |
| Frequency(HZ) | 50 | 50 |
| Rated Input Current(A) | 13.6 | 13.6 |
| Output Current Range(A) | 10-315 | 5-315 |
| No-load Voltage(V) | 51 | 51 |
| Rated Output Voltage(V) | 22.6 | 22.6 |
| Pre-flow(S) | 0-2 | 0-2 |
| Vale value current(%) | 20-80 | 20-80 |
| Down slope(S) | 0-10 | 0-10 |
| Post-flow(S) | 2-10 | 1-10 |
| Remote Contral | YES | YES |
| Arcing Way | Transfer | Transfer |
| Efficiency(%) | 85 | 85 |
| Duty Cycle(%) | 60 | 60 |
| Power Factor | 0.93 | 0.93 |
| Insulation Grade | F | F |
| Housing Protection Grade | IP215 | IP21S |
| Net Weight(kg) | 35 | 37.5 |
| Packing Dimension(mm) | 665*475*580 | 725*480*670 |
■ProductPurchase Guide
| Welding material | Plate thickness(mm) | Welding process | Current range(A) |
| Aluminumlloy | 0.3-5.0/4.0/16.0 | AC TIG | 10-2015 |
■Welding process
Stainless steel argon arc welding
Welding current:100/120A
Tungsten diameter: 𝜑1.6/2.4mm
Sheet type: 2/2.5mm stainless steel sheet
Wire diameter: φ2.0mm
Gas flow. 9-10L/min
DSL-3000/5000 NEW
■Applicable field
•Cabinet and kitchenware, kitchen supplies, stainless steel countertops, stainless steel sinks and water tanks.
■Features
•Suitable for 0.1mm-4mm sheet metal welding, Suitable for stainlesssteel,copper,iron,uminum, titanium, silver,gold and galvanized sheet, No distortion, no blackening, stable arcing,beautifulappearance,noneedforprofessional welders, no need for polishing and grinding treatment.
•Repair accuracy is high, the min repair quantity is 0.05 mm.
Less damage of base material: lesshot spot,no heating deformation of base material.
Power grid applicable range (AC187-253V).
The software has storage function, which isconvenient for the next direct call of welding after adjusting the parameters of different sheets.
●Higher no-load voltage design, easy arc, smallsplash, stable arc,beautiful shape.
•Adopting high speed fan, fast and all round heat emission, high duty cycle,over-voltage,over-current andoverheat protection.
■Productparameters
o O QQ150 Torch Ground clip
■Product Purchase Guide
| Productparameters | DSL-3000 | DSL-5000 |
| Input Voltage | AC220V±15% | AC220V±15% |
| Inout frequency (HZ) | 50/60 | 50/60 |
| Rating input power (KVA) | 3.6 | 4.8 |
| No-load voltage (V) | 52 | 56 |
| Current adjust range(A) | 1-200 | 1-200 |
| Min welding time | 1/10005S | 1/10005 |
| Instantaneous max power | ≥10kw | ≥10kw |
| No-load loss (W) | 20 | 20 |
| Duty cycle | 1-99% | 1-99% |
| Pulse frequency | 1-20HZ | 1-20HZ |
| Power | 3KW | 5KW |
| Insulation cdass | F | F |
| Housingprotectioncdass | IP21 | IP21 |
| Weight (KG) | 14 | 15 |
| Dimensions （CM） | 445*260*340 | 445*260*340 |
| Welding material | Plate thickness(mm) | Welding process | Current range(A) |
| Aluminum lloy | 0.2-0.5/2.0/4.0 | AC TIG | 10-10 |
■Welding process
Stainless steel argon arc welding
Welding current:100/120A
Tungsten diameter: 𝜑1.6/2.4mm
Sheet type: 2/2.5mm stainless steel sheet
Wire diameter: φ2.0mm
Gas flow: 9-10L/min
MZ1000/1250
IApplicable field
•Highway, Bridge, Special Heavy Steel Production, Large Power Plant Equipment Manulacturing,HeavySteelStructure,EquipmentManufacturingEnterprises, Construction Machinery.
■Features
• Double high power IGBT MODULE full bridge inverters, strong output power.
Anti-fluctuationability of power grid is strong, and power grid can work normally in 320V - 450V welding function.
•It has multi-function setings of submerged arc welding, hand welding and carbon arc air gouging, and has fixed point/scratch arc starting function.
Thedesignof submergedarcwelding(SAW)dropcharacteristic,which matcheswithvariablespeedwirefeeding.issuitableforheavycurrent welding of medium and heavy plates, and the maximum wire diameter can reachmorethan6.0mm.
●Equipped with dual-characteristiccarcontrol box (car display with digital meter;current/voltage preset,actual current/voltage digital display; car travel speed digital display).
●The functions of current/voltage preset and digital display are set, and the actual voltage and preset current are displayed when the drop characteristics of manual welding and submerged arc welding are decreased.
• The maximum power limit setting is adopted to protect the welding machine in an all-round way.
●It has_reliable overpressure, overcurrent, interception, overheating and protection measures.
●Excessive short circuit waveform control, stable welding, small spatter, beautiful shape, high reliability.
■Applicablefield
• Metal cabinet manufacturing, construction machinery repair, automobile parts, bicycle parts, special-shaped standard parts, crafts,electronic components,instrumentation,battery spot welding,metal spot welding,electrical switches,cable manufacturing,filters, silencers,metal packaging, chemical containers, wire mesh, basket and other metal products industries.
■Features
• Microcomputer Circuit Control with High Accuracy.
·Fine tuning of welding current from 20% to 100%.
•The control system has power factor adaptive function, and the pressure between electrodes can be adjusted and kept constant.
Widely used in automobile,aviation,construction, machinery, metal products, electrical switches and other industries.
•Welding of Low Carbon Steel, Wire and StainlessSteel Plate.
| Product parameters | MZ1000 | MZ1250 |
| Input Voltage(V) | AC380V±15% | AC380V±15% |
| Frequency(HZ) | 50 | 50 |
| Rated Input Current(A) | 84.3 | 105 |
| No-load Voltage(V) | 72 | 80 |
| Output Current Range(A) | 100-1000 | 100-1250 |
| Rated Output Voltage(V) | 44 | 44 |
| Arc Force Current Range(A) | 0-100 | 0-100 |
| Duty Cycle(%) | 100 | 100 |
| No-load Loss(V) | 300 | 300 |
| Efficiency(%) | 85 | 85 |
| Power Factor | 0.93 | 0.93 |
| Insulation Grade | F | F |
| Housing Protection Grade | IP21 | IP21 |
| Net Weight(kg) | 85.5 | 85.5 |
| Packing Dimension(mm) | 800*455*785 | 800*455*785 |
■Standardaccessories
■Productparameters
■ProductPurchaseGuide
| Base material | prWeldimm) | Diamieter | Current |
| 8.0-20 | 40/5.0/6.0000 |
■Weldingprocess
Carbon steel horizontal fillet welding
Welding current: 230/300A Welding rod diameter: p4.0/5.0 Sheet type: 10/16mm carbon steel sheet
| Product parameters | DTN-25 |
| Input Voltage(V) | AC380V±15% |
| Frequency(HZ) | 50 |
| Rated Input Power(KW) | 25 |
| Rated Input Curent(A) | 66 |
| No-load Voltage(V) | 2-4.13 |
| Duty Cycle(%) | 20 |
| Machine Arm Length(mm) | 420 |
| Machine Arm Distance(mm) | 200 |
| Top Electrode Move Distance(mm) | 100 |
| Top Electrode Force(N) | 2350 |
| Low Carbon Steel Thickness(mm) | 2.5+2.5 |
| Air Pressure(mPa) | 0.6 |
| Cooling Water Flow(L/H) Net | 120 |
| Weight(kg) | 182 |
| Machine Dimension(mm) | 885x490x1545 |
