Product Specification

Name: EMS- Smart Microgrid controller Model: HMQ-EMS-300 series

Thank you for choosing our products, please read this product manual carefully before use.

contents

1. Safety precautions ...

1.1. Universal safety ...
1.2. Grounding safety ....
1.3. Personal safety ....
1.4. Equipment safety ...
1.5. Personnel requirement ...
2. Production introduction .. 4
2.1. Production appearance . 4
2.2. Structure size . 7
2.3. Production order description .. 8
2.4. Specification parameter . 9
3. Interface and display distribution ... .12
3.1. Power interface ... 12
3.2. HDMI output interface ... . 14
3.3. Ethernet interface .. 15
3.4. Audio interface ... .. 15
3.5. USB interface .... . 16
3.6. Memory card socket ... . 16
3.7. WIFI antenna interface ... 17
3.8. 4G antenna interface . .17
3.9. KEY .... .18
3.10. Communication interface ... 18
3.11. DI input interface . .20
3.12. DO output interface ... .21
3.13. Indicator light .... . 24
4. Packing List . 25

5. Connect . 26

1. Safety precautions

Notice

• The EMS-smart microgrid controller has been designed and tested in accordance with safety regulations. However, as an electrical device, you must follow the safety instructions before performing any operation on the device. Improper operation may result in serious injury or property damage.

1.1. Universal safety

Danger

• The document content may be updated from time to time due to product version upgrade or other reasons. Without special agreement, the document content cannot replace the safety precautions on the product label. All descriptions in this document are for use only.
• Read this document carefully to understand the product and precautions before installing and using the device.
• The manufacturer shall not be liable for device damage or personal injury caused by failure to install, use, or configure the device in accordance with the requirements of this document or the corresponding user manual.

1.2. Grounding safety

1.3. Personal safety

• Use insulation tools and wear personal protective equipment to ensure personal safety. • When the device is short-circuited, do not touch the device and turn off the power immediately. • Before connecting the device, turn off all upper-level switches to ensure that the device is not powered on.

1.4. Equipment safety

Warn

• Store the device in an appropriate temperature and humidity environment and in a clean, dry and well-ventilated area.

• When installing and maintaining the equipment, use the appropriate tools and follow the correct

operation procedures.
• When operating the device, strictly comply with local standards and safety regulations to ensure safety.
• After installing the device, remove empty packaging materials, such as cartons, foam, plastic, and cable ties, from the device area.
• Unauthorized removal or modification of the equipment may cause damage to the equipment, which is not covered by the warranty.

1.5. Personnel requirement

Notice • Equipment installation and maintenance personnel must receive rigorous training, fully understand the safety precautions of various products, and master the correct operation methods. • Only qualified professionals or trained personnel are allowed to install, operate, maintain, and replace the equipment. • Personnel other than those operating the equipment should stay away from the equipment to ensure safety.

2. Production introduction

EMS- Smart microgrid controller, designed for modern microgrid systems, with a variety of models and configuration options, designed to meet the energy management needs of different energy storage plants, can significantly improve the efficiency and stability of energy storage plants.

Core functions: data collection, reporting and analysis, monitoring and control, mode policy configuration, parameter configuration, device control management, alarm management, communication and other functions.

Features: It can adjust the charge and discharge strategy of the energy storage device in real time according to the demand and load of the power grid. By coordinating the relationship between supply and demand, the energy regulation function of the energy storage equipment is fully exerted, the utilization efficiency of energy is improved, and the stable operation of the energy storage power station is provided with a strong guarantee. It is closely integrated with the energy storage system, transformer and distribution system and auxiliary system, which can further improve the operation efficiency and stability of the energy storage power station.

2.1. Production appearance

P2-1 Front view with screen

P2-2 Front view without screen

P2-3 Dc power input without screen

P2-4 Side view of DC power input <br>P2-5 Ac and DC power input side view

Note: The appearance of the product is subject to the actual product, and this document is only for illustration.

2.2. Structure size

P2-6 Product assembly dimensions drawing

Note: Product size for reference, specific to the physical subject.

2.3. Production order description

This article mainly involves the following HMQ-EMS-300 order number：

P2-7 Model + order identification

The meanings of order fields and letters are as follows：

T2-1 Model + order number identification description

2.4. Specification parameter

T2-2 Parameter list

3. Interface and display distribution

P3-1 Appearance of the front-end port

P3-2 Appearance of the back-end interface

Note: The specific port style of the product will vary according to the selected configuration, and the specific object shall prevail.

3.1. Power interface

EMS- The power supply of the smart microgrid controller is optional. The power supply can be automatically switched between AC and direct power supplies or DC power supplies.

The interface terminals of the DC input power supply are 3-pin green sockets with 3 . 8 {mm } spacing. The sockets are equipped with screw holes and connected to the DC2.0 round core jack. The DC power input is equipped with a 24VDC sliding switch. For power cables, use 0.2 to 1 . 5 {mm } ^ { 2 } copper cables or 24AWG to 16AWG dual-core copper cables. The PGND cable uses 4 to 6 {mm } ^ { 2 } copper cables or 12AWG to 10AWG outdoor copper cables.

The interface terminals of the AC input power supply are 3-pin green sockets with a distance of 7 . 5 {mm } . The sockets are provided with screw holes. Power input installed 220VAC boat type switch. Power cables are connected to copper cables with a diameter of 2 . 5 {mm } ^ { 2 } . The PGND cable uses 4 to

6 {mm } ^ { 2 } copper cables or 12AWG to 10AWG outdoor copper cables.

P3-3 AC\DC dual power interface

G + 12-24MDC-IN OFFON12-24VDC-IN 24VDC开关面面面

P3-4 DC power interface

The following table describes the meanings of interface terminals：

The EMS- Smart microgrid controller provides two 5W power outputs, one 12VDC output, and the other 24VDC output, for 220VAC AC power supply if AC/DC power supply is automatically switched. The interface terminals are two 3-pin green sockets with 3 . 8 {mm } spacing. The sockets have screw holes. For power cables, use 0.2 to 1 . 5 {mm } ^ { 2 } copper cables or 24AWG to 16AWG dual-core copper cables.

3.2. HDMI output interface

The EMS- Smart Microgrid controller provides a standard HDMI interface that can be used to connect to the HDMI interface display. The HDMI interface is the same as the on-board TFT-LCD interface. Only one of the two interfaces can be selected at the same time.

3.3. Ethernet interface

The EMS- Smart Microgrid controller provides 2 Ethernet interfaces, and the physical interface uses an RJ45 with isolation LED indicator.Gigabit ETH is the core board native Ethernet port, and 100 megabit ETH is the PRG extended Ethernet port.

3.4. Audio interface

The EMS- Smart Microgrid controller provides a 3 . 5 {mm } audio interface that can be used to connect the 3 . 5 {mm } GB audio plug.

3.5. USB interface

EMS- Smart Microgrid controller provides three USB interfaces, the interface definition and functions are as follows:

3.6. Memory card socket

The EMS- Smart Microgrid controller provides a standard MicroSD card socket for system debugging, firmware writing, startup, and firmware upgrade. After the system is started, users can read and write the SD card.

T3-7 Memory card socket description

Note: The SD card is recommended to be an appropriate brand and the storage space is 64 GB or 128GB.

3.7. WIFI antenna interface

The EMS-Smart Microgrid Controller provides 1 WIFI antenna interface, with the onboard WIFI module being the industrial-grade B-LINK BL-R8188EU2, featuring an SMA interface with an input impedance of 5 0 \Omega , and an external 2.4G WIFI module antenna.

3.8. 4G antenna interface

The EMS- Smart Microgrid controller provides a 4G antenna interface and is matched with a Micro SIM card holder. The 4G module expansion interface uses the onboard Mini PCIe slot, which can be compatible with a variety of LTE Cat1 and LTE Cat4 wireless communication modules such as Yiyuan, Youfang, and Guanghetong

3.9. KEY

The EMS- smart microgrid controller provides two buttons. The Reset Key button is used to control system reset and power off of the PSU, and the other Upgrade Key button is used to upgrade programs.

3.10.Communication interface

The EMS-Smart Microgrid Controller provides 2 isolated CAN interfaces and 5 isolated RS-485 interfaces.

The interface terminal uses a 14Pin, 3 . 8 {mm } pitch green socket with screw holes. Both CAN and RS485 use 2-core shielded copper twisted pair cables, with a wire diameter of 0.5 to 0.75 square millimeters and a twist pitch of 20 millimeters. Strip the outer insulation of the wire ends to 7 . 1 0 {mm } , and it is recommended to connect the shielding layer to the control terminal ground.

A1 B1 A2 B2 A3 B3 A4 B4 A5 B5 H1 L1 H2 L2 · 西西西西西西西商西酒

P3-5 Communication interface

The meanings of interface terminals are as follows:

3.11.DI input interface

EMS-Smart Microgrid Controller can provide 4 or 8 channels of optocoupler isolated DI input interfaces. The interface terminal is a 1-channel 4Pin, 3 . 8 {mm } pitch green socket with built-in screw holes. It is recommended to use 2-core copper shielded wire for DI, with a wire diameter of 0.5 to 0.75 square millimeters. DI's -DI_COM are all connected.

DI1DI2DI3DI4COM西西西西面

P3-6 DI Input interface (Optional 1)

DI1DI2DI3DI4COM西西西西西

DI5DI6DI7DI8C0M西西西西面

P3-7 DI Input interface (Optional 2)

The meanings of interface terminals are as follows:

P3-8 EMU-1000-10 Schematic diagram of circuit principle of wet contact DI

3.12.DO output interface

P3-9 DO output interface（optional 1）

EMS-Smart Microgrid Controller can provide 2 or 8 channels of relay-isolated passive DO (Digital Output) interfaces, which can be used to control the power on/off of external devices or as switches, etc. When the number of DI (Digital Input) input interfaces is 4, the number of DO output interfaces is 2; if the number of DI input interfaces is selected as 8, then the number of DO output interfaces is also 8. The interface terminal is a 1-channel 6Pin, 3 . 8 {mm } pitch green socket with screw holes. It is recommended to use single-core multi-strand wire with a diameter of 0 . 5 { ~ } 1 square millimeters for DO, and each channel of DO is independent.

D01+ D01-D02+ D02-西西西面

DO1+DO1-DO2+DO2-DO3+DO3-DO4+DO4-D05+D05-DO6+D06-D07+DO7-DO8+D08西西西酒西西酒酒西面

P3-10 DO output interface（optional 2）

The meanings of interface terminals are as follows:

T3-13 DO output interface description

3.13.Indicator light

The EMS-Smart Microgrid Controller offers an optional TFT-LCD touch display screen, and the LED indicator system covers the status display of power, operation, alarm, 4G, CAN1, CAN2, 485/1-5, DO, and DI. For the 300LD11CN model, there are two optional configurations for DO and DI: Configuration One includes DO/1-2 and DI/1-4 indicators; Configuration Two does not include these indicators. The design of these indicators aims to facilitate users in understanding the system's operational status under any circumstances.

P3-11 Indicator light

The meanings of indicators are as follows:

4. Packing List

5. Connect

Wechat account 品 懿 ] ■ 可 ■

Official website

Hunan Huimingqian digital Energy Technology Co., LTD

Add：Changsha High-tech Development Zone, Dongfanghong North Road No. 601, Media Art

Industrial Park Building A-1, Rooms 702-704

Web：www.hncbyun.com

Tel：400-853-1766