该页无缩略图
CONSTRUCTION WOODEN PANELPRODUCT SPECIFICATION INTRODUCTION
01 FILM FACED PLYWOOD
02 LEONKING 3 PLY SHUTTERING PANE
03 F17 LAMINATED VENEER LUMBER
04 H20 BEAM
05 TIMBER
06 CDX PLYWOOD
07 ANTI SLIP FILM FACED PLYWOOD
08 CIRCULAR FILM FACED PLYWOOD
09 PLASTIC FILM FACED PLYWOOD
MDO FILM FACED PLYWOOD
OSB-ORIENTED STRAND BOARD
12 PRESSURE TREATED TIMBER
THICKNESS
Customized size&Thickness
FILM FACED PLYWOOD
FORMAT SIZE
PIANOPLYWOOD
PRODUCT CERTIFICATE
Casting up to 30 times
STANDARD
MATERIAL
Free samples&Prompt delivery
Prov. cust. logo&Design
1220x2440 mm
6/9/12/15/18/21 mm
Eco-friendly&Visualization
High standards&Quality
DENSITY
MOISTURE CONTENT
Poplar / Eucalyptus / Birch / Pine / Hardwood / Finger joint
BS EN 314-2 / BS EN 315 / BS EN 316 / BS EN 636
500-700 kg/m³
8%-12%
WWW.PIANOPLYWOOD.COM
INSTRUCTIONS FOR USE AND MAINTENANCE OF FORMWORK PANELS
USAGE
The formwork panels are mostly used in construction for concrete shuttering. Before usage, the user/contractor should check whether the panel surface quality is sufficient for the desired concrete surface quality. As the formwork panels are made of solid wood, wood texture can be visible on the concrete surface. Therefore, the formwork panel producer does not undertake any responsibility for the quality of the concrete surface. After use, traces of the edge protective varnish on the concrete surface may also be visible.
The panels are supported at intervals as specified in the diagram of intervals in the producer's brochure.
When assembling or disassembling formwork panels, utmost attention should be paid to minimising the damage to the panels through the use of saws, nails or other fasteners. You should also be careful not to damage the surface of the boards with a hammer or sharp objects. Such damages inevitably affect the quality of the concrete surface
Before applying concrete, the panels should always be treated with formwork oil and thoroughly moistened/sprinkled with water in order to minimise the risk of the concrete sticking to the panels. You should be very careful when removing the shuttering, especially if the panels are nailed, screwed or fastened in any other way. It is essential to prevent the falling of the panels from greater heights and any resulting damage which might occur.
• MAINTENANCE
After use, the panels should be cleaned of all residues and placed on a flat surface. For the protection of the shuttering, a paraffin paste or formwork oils should be used in accordance with the producer's instructions. The panels should be kept in a covered and shady place. If stored outdoors, the panels should be covered with a sheet (a tarpaulin plane) protecting them against harmful weather conditions (sun, rain). If the panels are exposed to the sun, splits and/or cracks may appear on the outer layer. Such panels must be properly moistened with water before next use!
Apart from that, fading (discolouration) may appear on the surface protection, which, however, does not significantly affect the functionality of the panel. Due to the components and the colours of wood, the panels may stain brownish when exposed to rain.
WARNING
In extreme weather conditions (significant deviations from normal humidity and temperature, or longer periods of dry and hot weather), you should take extra care of the shuttering, mostly making sure that the panels are not exposed to the heat of the sun for longer periods. Should you fail to do so, longitudinal cracks on the outer layer may appear, which significantly affect the lifetime of formwork panels and the quality of the concrete surface. Such panels should be properly moistened with water before use, otherwise, they might be permanently damaged due to the intrusion of the concrete emulsion into the cracks!
Moreover, wooden formwork panels contain certain wood components, such as tannic acid or resins, which might cause stains on the concrete surface
CONCRETE FORMWORK SHUTTERING PANELS
The largest range of products, the largest choice
Our sorting diversity can satisfy any customer need: 21 mm and 27 mm shuttering panels with and without galvanized edge protection (Metal or plastic), 27 mm shuttering panels with or without edge band, solid timber profiles with edge protection in dimensions of 20 mm, all in big and small size. The application possibilities go from ceiling boards to wall, bridge and tunnel formworks to work platforms.
3 Ply Shuttering Panel with Plastic Endling
3 Ply Shuttering Panel with Metal Endling
Fax/Tel: +86-21-50792750
PHN/WA/WX: +86-133 1189 1208
RobertWang@pianoplywood.com
www.pianoplywood.com
Casting up to 20 times
Customized size
Free samples&prompt delivery
High standards
FORMAT SIZE
LENGTH
WIDTH
THICKNESS
MATERIAL
STANDARD
3000×500×21/27 mm,2000×500×21/27 mm
1000/1970/2000/2500/2970/3000mm
250/450/500/1000 mm
21 /27 mm
Spruce / Fir /Pine
EN 13353 / EN 12775 / EN 314-2
WWW.PIANOPLYWOOD.COM
RobertWang@pianoplywood.com
3 PLY SHUTTERING PANEL
TECHNICA DATA
| Product | 3-ply yellow concrete formwork shuttering panelcoated with melamine resin that allows a resistantand smooth surface | Leonking panel 21 mmLeonking panel 27mm | ||
| Wood species | Spruce/Fir/Scotch Pine/Radiata Pine | |||
| Wood moisture | 12% ±2% | |||
| Weight | 12 kg/m2 (27 mm) / 10kg/m2 (21 mm) | |||
| Formats (mm) | 1000x500 - 1500x500 - 2000x500 - 2500x500 - 3000x500 | |||
| Thickness (mm) | 21,27 | |||
| Surface protection | Highly resistant melanine coating, extremely smooth surface | |||
| Edge seal | Water repellent edge formork finish, yellow,red | |||
| Endling | without or Metal or Plastic | |||
| Packaging | Fir:21mm/120pcs package,27mm/96pcs package;Spruce:21mm/110pcspackage,27mm/88pcs package | |||
| Design values | Mechanical properties 21 | mm 27 | mm | |
| Minimal value | 40N/mm2 | 40N/mm2 | ||
| Modulus of elasticity(mean value) | 11000-12000 N/mm2 | 11000-12000 N/mm2 | ||
| Note | The values are calculated with a wood moisture of 12%. With heavy moisturepenetration up to fiber saturation point, the values for bending strenght and flexural modulusof elasticity may be up to 30% lower | |||
| L | |||||||||
| d=21 mm | 0.40 | 0.45 | 0.50 | 0.55 | 0.60 | 0.65 | 0.70 | 0.75 | |
| q | 5 kN/m2 | 0.11 | 0.17 | 0.26 | 0.38 | 0.54 | 0.75 | 1.00 | 1.32 |
| 10 kN/m2 | 0.21 | 0.34 | 0.52 | 0.77 | 1.08 | 1.49 | 2.01 | 2.65 | |
| 15 kN/m2 | 0.32 | 0.51 | 0.78 | 1.15 | 1.63 | 2.24 | 3.01 | 3.97 | |
| 20 kN/m2 | 0.43 | 0.69 | 1.05 | 1.53 | 2.17 | 2.99 | 4.02 | 5.30 | |
| 25 kN/m2 | 0.54 | 0.86 | 1.31 | 1.91 | 2.71 | 3.74 | 5.02 | 6.62 | |
| 30 kN/m2 | 0.64 | 1.03 | 1.57 | 2.30 | 3.25 | 4.48 | 6.03 | 7.95 | |
| 35 kN/m2 | 0.75 | 1.20 | 1.83 | 2.68 | 3.80 | 5.23 | 7.03 | 9.27 | |
| 40 kN/m2 | 0.86 | 1.37 | 2.09 | 3.06 | 4.34 | 5.98 | 8.04 | 10.59 | |
| L | |||||||||
| d=27 mm | 0.40 | 0.45 | 0.50 | 0.55 | 0.60 | 0.65 | 0.70 | 0.75 | |
| q | 5 kN/m2 | 0.05 | 0.08 | 0.12 | 0.18 | 0.26 | 0.35 | 0.47 | 0.62 |
| 10 kN/m2 | 0.10 | 0.16 | 0.25 | 0.36 | 0.51 | 0.70 | 0.95 | 1.25 | |
| 15 kN/m2 | 0.15 | 0.24 | 0.37 | 0.54 | 0.77 | 1.05 | 1.42 | 1.87 | |
| 20 kN/m2 | 0.20 | 0.32 | 0.49 | 0.72 | 1.02 | 1.41 | 1.89 | 2.49 | |
| 25 kN/m2 | 0.25 | 0.40 | 0.62 | 0.90 | 1.28 | 1.76 | 2.36 | 3.12 | |
| 30 kN/m2 | 0.30 | 0.48 | 0.74 | 1.08 | 1.53 | 2.11 | 2.84 | 3.74 | |
| 35 kN/m2 | 0.35 | 0.57 | 0.86 | 1.26 | 1.59 | 2.46 | 3.31 | 4.36 | |
| 40 kN/m2 | 0.40 | 0.65 | 0.98 | 1.44 | 2.04 | 2.81 | 3.78 | 4.98 | |
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
www.pianoplywood.com
q = load
(N/m2) L = span (m)
d = 21 mm
E = 10000N/mm2 of extrapanel
with d=21 mm
K = 0.646 deformation factor contingent on number of fields for constant load
q = load
(N/m2) L = span (m)
d = 27 mm
E = 10000N/mm2 of extrapanel
with d=27 mm
K = 0.646 deformation factor contingent on number of fields for constant load
3 PLY SHUTTERING PANEL
3 PLY SHUTTERING PANEL CORE
CORE TYPE - GRADE
\*Product grades (Grade S/A/B/C) are determined based on the following Key Performance Indicators: Structural strength, Weather resistance, Stability, Water absorption and Expansion Rate, Corrosion resistance, Demolding performance, Bonding firmness, Flatness, Service life, Wood species selection differentiation.
\*The only advantage of Knot-free wood in construction lies in its appearance, merely serving an aesthetic purpose.
There is no difference in the core performance between wood with Knots and without Knots.
3 PLY SHUTTERING PANEL
FORMWORK PANEL WITH METAL ENDING
Solid Wood Panels
Joint-free surfaces for visually beautiful concrete quality The surface finish of our solid wood panels increase the life duration and allows an easy stripping and cleaning. The smooth surfaces gives furthermore visually beautiful concrete quality and joint-free surfaces. The edge protection with C-profile make solid wood panels more durable.
PRODUCT ADVANTAGES
Accurate & Stable Dimensions
Long service life
With metal endling
High structural strength
Environmental Protection
Waterproof
Long service life
PlANO 3-layered shuttering panels impress thanks to the high stability and dimensional accuracy. Both longitudinal external layers and the diagonal central layer are glued between them and water-resistant. Swelling or shrinking are almost excluded thanks to this structure. Optional edge protection and a high quality waterproofing impregnation further increase the durability and make stripping and cleaning easy.
Fax/Tel: +86-21-50792750
WA BUSINESS
3 PLY SHUTTERING PANEL
FORMWORK PANEL WITH PLASTIC ENDING
PACKING EFFECT
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
3 PLY SHUTTERING PANEL
Fax/Tel: +86-21-50792750
PHN/WA/WX: +86-133 1189 1208
PIANOPLYWOOD
LEONKING 3 PLY SHUTTERING PANEL ACCESSORY
Tie rods, formwork clamps, tie-brackets and ties forpillar casting, nuts and cones.
Find the solution you need. Or discover new ones.
Iron spacers for wooden panels 100-1200mm R 70kg/mm2
Helicoidal stanchion 500mm weight 0,90kg
Stanchion pressed hook 500mm weight 0,85kg 1000mm weight 1,60kg 1500mm weight 2,40kg
Pre-galvanised U-shaped
element
630mm weight 1,00kg n2 holes
1130mm weight 1,80kg n°3
holes
Tie-brackets for pillar 150-450mm 500-950mm weight 2,35kg
200-400mm weight 9,30kg
250-500mm weight 10,40kg
250-600mm weight 11,90kg
400-800mm weight 16,50kg
600-1000mm weight 28,50kg
Galvanised wedge weight 0,115kg
Wedge for ties weight 0,40kg
PIANOPLYWOOD
3 PLY SHUTTERING PANEL
| LEONKINGwww.pianoplywood.comE-mail:RobertWang@pianoplywood.com | material | Q235 | products | corner protectors |
| Thickness | 2.3cm | Drawing no. | U12353-20240301 | |
| Tolerance | +/-0.2mm | Standard | U12352 | |
| Size | 14.35*14*35*20.29 | Page | 1/4 | |
| Address: Block F,Floor 8,NO.58,New JinqiaoRD,Pudong District,Shanghai201206,China上海沁格建筑材料有限公司 | ||||
SHANGHAI QIN GE CERAMIC & BUILDING CO.,LTD.
3 PLY SHUTTERING PANEL
| LEONKINGwww.pianoplywood.comE-mail:RobertWang@pianoplywood.com | material | Q235 | products | corner protectors |
| Thickness | 2.3cm | Drawing no. | U12353-20240301 | |
| Tolerance | +/-0.2mm | Standard | U12352 | |
| Size | 14.35*14*35*20.29 | Page | 2/4 | |
| Address: Block F,Floor 8,NO.58,New JinqiaoRD,Pudong District,Shanghai201206,China上海沁格建筑材料有限公司 | ||||
SHANGHAI QIN GE CERAMIC & BUILDING CO.,LTD.
WA BUSINESS
3 PLY SHUTTERING PANEL
| LEONKINGwww.pianoplywood.comE-mail:RobertWang@pianoplywood.com | material | Q235 | products | corner protectors |
| Thickness | 2.3cm | Drawing no. | U12353-20240301 | |
| Tolerance | +/-0.2mm | Standard | U12352 | |
| Size | 14.35*14*35*20.29 | Page | 3/4 | |
| Address: Block F,Floor 8,NO.58,NewJinqiaoRD,Pudong District,Shanghai201206,China上海沁格建筑材料有限公司 | ||||
SHANGHAI QIN GE CERAMIC & BUILDING CO.,LTD.
WA BUSINESS
| LEONKINGwww.pianoplywood.comE-mail:RobertWang@pianoplywood.com | material | Q235 | products | corner protectors |
| Thickness | 2.3cm | Drawing no. | U12353-20240301 | |
| Tolerance | +/-0.2mm | Standard | U12352 | |
| Size | 14.35*14*35*20.29 | Page | 4/4 | |
| Address: Block F,Floor 8,NO.58,New JinqiaoRD,Pudong District,Shanghai201206,China上海沁格建筑材料有限公司 | ||||
SHANGHAI QIN GE CERAMIC & BUILDING CO.,LTD.
WA BUSINESS
PRODUCT DESCRIPTION ADJUSTABLE COLUMN CLAMPS
Adjustable Column Clamps is an innovative steel formwork clamp, which is applicable to the reinforcement of cast-in-situ reinforced concrete square column formwork commonly used in engineering construction.Such as mall,hospital,warehouse ...
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
www.pianoplywood.com
ADJUSTABLE COLUMN CLAMPS
ADJUSTABLE COLUMN CLAMPS
SQUARE POST BUCKLE
STEEL WEDGES
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
INSTALLATION INSTRUCTIONS
Attach the column clamps to the corner clamps. Fasten the head of each column clamp into the bent end of the corresponding clamp. Ensure the column clamp is tightly aligned and flush with the beam.
RobertWang@pianoplywood.com
Customized size&thickness
Corrosion resistance
Waterproof
Eco-friendly&visualization
FORMAT SIZE
LENGTH
WIDTH
THICKNESS
STANDARD
2700/3600/4500/5400/6000/7200/9600/12000 mm
MATERIAL
MOISTURE CONTENT
Up to 12000 mm
35/45/63/70/90/140/240 mm
35/45/63mm
AS NZS 4357 / AS NZS 1080.1
BS EN 24829 / BS EN 14279
Larch / Spruce / Radiata pine
8%-12%
WWW.PIANOPLYWOOD.COM
Environmentally friendly
Free samples&prompt delivery
Customized size&thickness
High quality
High standards
FORMAT SIZE
SIZE
MATERIAL
STANDARD
200×80×40×27mm
Flange size: 40 × 80 mm × 3000-5900 mm Web size: 27 /90 ×120 mm×3000-5900 mm
Flange: sawed pine / spruce , LVL / timber Web： birch / poplar / larch,plywood
EN 13377 / EN 1993-1 / EN 10034
DENSITY
5.3-5.4 kg/m³
MOISTURE CONTENT
8%-12%
WWW.PIANOPLYWOOD.COM
LEONKING LK20 and E-Ply Piano H20 formwork beams are solid web girders and subject to supervision level super a according to EN13377 & GB/T 28985-2012.
Monitoring and certification by material research laboratory at SGS-CSTC Standards Technical Services Co.,Ltd. Xiamen Branch and wood products quality & inspection center of state forestry and grasslang Adinstration (Nanjing).
Product range
Lengths:180,195, 250, 265, 275, 290, 300, 330, 360, 390, 450, 490, 590 cm
E-Ply Piano H20: protection cap possible up to 9 m – over 9 m only cut straight
LK20: rounding with sealing possible up to 9 m – over 9 m only cut straight
Special lengths possible up to 11.90 m
Characteristic limits
Lateral force Contact resistance Bending moment Rigidity I
Vk = 23.9 kN Rb,k = 47.8 kN Mk = 10.9 kNm E1 = 450 kNm²
Measurements
Size tolerance: height H=200 +/-2 mm Length tolerance: specified length +/- 10 mm
Weight: approx. 4.8 kg/m
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
Permissible values:
Shear force
Q = 11 kN
The chords are mechanically tested for stress grading.
A support reaction
A = 22 kN
Bending moment
M = 5 kN
Formwork beam features:
Girder length Manufacturer information: name, logo Custom labeling, client logos possible
Girder typesClassification
Monitoring level M
Product identification number
Country of origin
Measuring table forms:
To calculate table forms please see the
two tables to the right with the maximum permissible yoke, cross and support beam spacing. The specified influence lines may not be exceeded anywhere.
Measurement table:
Example:
Given: Ceiling thickness (20 cm) + cross-beam spacing (75 cm)
Sought: Yoke-beam spacing + support spacing
1 Ceiling thickness: 20 cm
2 Cross-beam spacing: 75 cm
3 Permissible yoke-beam spacing according to table 1 = 2.56 m
4Select same or next smaller yoke-beam spacing in table 2 = 2.5 m
5 Choose value 2.50 in table 2, choose the value for ceiling thickness (20 cm) and read the permissible support spacing value: 1.2 m
6 Attention: The corresponding bearing capacity of the supports must be verified!
Regulations for installation:
The fitting of the formwork beams must be performed by professional and trained personnel in accordance with our application guidelines and safety instructions.
The permissible open span of the LK20 and the E-Ply Piano H20 may not exceed 4,0 m. The sheeting is to be nailed directly onto the upper chord.
Wooden formwork beams should only be utilized in an upright position and must be securely fastened to prevent tipping, as per static requirements.
Changes of the product are prohibited and can cause increased hazard potential.
Regulations of use:
Every item must be inspected by the installation firm and may only be used if in perfect condition.
Formwork beams that are damaged or weakened by decay are not to be used.
Please observe that the formwork beams should not be stored in a way that they are exposed to heavy climatic influences and should not be stored out side unprotected. A professional storage increases the general endurance and reduces deformation and crack formation.
Fax/Tel: +86-21-50792750
| Crss-bam pcing (m)Yoke-beam spacing (m) | |||||||||||||||
| Cross-beam spacing (m) | |||||||||||||||
| (am)Fl otrisDRETET | TotloadkN/m2 | ||||||||||||||
| 0,500,630,670,751 | ,001,251,501,752,002,252,503,003,50 | ||||||||||||||
| Max. distance betwecross beams (m) | en | Max. distance between yoke-beams (m)= max. distance between ceiling support beams | |||||||||||||
| 10 | 4,40 | 3,63 | 3,37 | 3,29 3,1 | 72 | ,882 | ,67 | 2,462,28 | 2,13m2,01 | 1,9 | 11,671 | ,43 | |||
| 12 | 4,92 | 3,433,19m | 3,123,0 | 02 | ,722,53 | 2,332,16m | 2,02...1,90... | 1,791,49 | 1,28 | ||||||
| 14 | 5,44 | 3,27 | 3,04m | 2,9712,8 | 62 | ,60 | 2,41 | 2,41 | 2,05m | 1,921,80 | 1,62…... | 1,35 | 1,16 | ||
| 16 | 5,96 | 3,14 | 2,92 | 2,852, | m | 2,49. | 2,31 | 2,12 | 1,90m | 1,831,64 | ,48: | 1,23 | 1,05 | ||
| 18 | 6,48 | 3,03 | 2,81 2 | ,752,6 | 52 | ,40 | 2,22 | 2,03 | 1,88m | 1,70m1,51 | 1,36 | 1,130 | ,97 | ||
| 20 | 7,00 | 2,932 | ,722 | ,6622,56 | 2,32 | 2,14 | 1,95 | 1,80 | 1,571,40 | 1,2 | 1,051 | 0,90 | |||
| 22 | 7,52 | 2,84 | 2,64 | 2,582,48 | 2,26 | 2,06 | 1,88 | 1,67 | 1,46 | 1,30 | 1,17 | 0,981 | 0,84 | ||
| 24 | 8,04 | 2,76.. | 2,57m | 2,51mm2,42 | 2,19 | 2,00 | 1,82 | 1,56m | 1,37m | 1,22 | 1,09…. | 0,91 | 10,78 | ||
| 26 | 8,56 | 2,70 | 2,50m | 2,452,35 | 2,14 | 1,93 | 1,71 | 1,47 | 1,29 | 1,14 | 1,030 | ,860 | ,73 | ||
| 28 | 9,08 | 2,63 | 2,44mm | 2,3992,300 | 2,09 | 1,88 | 1,62 | 1,38m | 1,21m.. | 1,08 | 0,97 | 0,81 | 0,69 | ||
| 30 | 9,66 | 2,57 | 2,39 | 2,342,25 | 2,03 | 1,82 | 1,52 | 1,30 | 1,14 | 1,01 | 0,91 | 0,76 | 60,65 | ||
| 35 | 11,22 | 2,45 | 2,27m | 2,2312,14mm | 1,89 | 1,57 | 1,31m | 1,12 | 0,981 | 0,87 | 0,780 | ,650 | ,56 | ||
| 40 | 12,78 | 2,35 | 2,18 | 2,132,04 | 1,72 | 1,38 | 1,15 | 0,98m | 0,86 | 0,77 | 0,69 | 0,570 | ,49 | ||
| 45 | 14,34 | 2,26. | 2,102 | ,04 | 1,53 | 1,23 | 1,02 | 0,88m | 0,770,68 | 0,610 | ,51 0 | ,44 | |||
| 50 | 15,90 | 2,18 | 2,0111 | ,94 | 1,38... | 1,11 | 0,920 | ,791 | 0,69ARR0,610 | ,550 | ,460 | ,40 | |||
Yoke-beam spacing
www.pianoplywood.com
FORMWORK H20 BEAM
DIFFERENCES IN THREE GRADES OF H20 BEAMS:
GradeS / Grade AA / Grade A levels of parameters
| GRADE S | GRADE AA | GRADE A | ||
| WEB | Pine LaminatedVeneer Lumber(LVL), Grade F17 | Pine LaminatedVeneer Lumber(LVL), Grade F11 | Spruce Core3 Ply ShutteringPanel | Combi CoreCrossbandingPlywood |
| DENSITY | 750 kg/m³ | 650 kg/m³ | 470 kg/m³ | 600 kg/m³ |
| ELASTICMODULUS(MPA) | ≥14000 | ≥10500 | ≥10000*Full-length | ≥8000*Full-length |
| SUPPORTLENGTH | Full-length LVL | ≤ 3m Full-length≥ 3m Spliced together | ≤ 2.5m Full-length≥ 2.5m Spliced together | |
| WEIGHT | 5.2 kgs/m | 5.1 kgs/m | 4.9 kgs/m | 5.0 kgs/m |
| FLANGE | Superior quality Spruce finger jointed solid wood timber | |||
| OTHERS | Phenolic adhesive,With Fully Enclosed Plastic Heads on Both Ends | |||
The diagram shows Grade S
Unit: mm
Environmentally friendly
Customized size&thickness
LENGTH
WIDTH
THICKNESS
PROCESS
Free samples&prompt delivery
STANDARD
Up to 12000 mm
2400/3000/3600/4200/4800/6000/7200/12000 mm
MATERIAL
50/75/100/125/150/175/200/225/250/300mm
47/75/100 mm
Douglas fir/ spruce/ fir/ radiated pine larch/ Mongolian pine/ birch/ ash basswood/ walnut/ cherry/ oak/ southern yellow pine
BS 4978 / EN 14081 / ISO 737
ISO 1029 / ISO 2299 / ISO 4470
Pressure treated / Carbonized
WWW.PIANOPLYWOOD.COM
Visualization
High standards&quality
RobertWang@pianoplywood.com
Fax/Tel: +86-21-50792750
PRODUCT CERTIFICATE
CDX PLYWOOD
PIANOPLYWOOD
Environmentally friendly
Customized size&thickness
Free samples&prompt delivery
High standards
Visualization
High quality
FORMAT SIZE
THICKNESS
OTHER SIZE
2.7-24 mm
Customized size and thickness
STANDARD
BS EN 314-2 / BS EN 315 / BS 6566 / EN 13353 / EN 12775
DENSITY
MOISTURE CONTENT
500-630 kg/m³
8%-12%
WWW.PIANOPLYWOOD.COM
RobertWang@pianoplywood.com
ANTI SLIPFILM FACED PLYWOOD
PIANOPLYWOOD
PEFC
Environmentally friendly
Customized size&thickness
FORMAT SIZE
THICKNESS
MATERIAL
STANDARD
DENSITY
MOISTURE CONTENT
Free samples&prompt delivery
High standards
1200×2400 mm/1220×2440 mm/1250×2500 mm
9/12/15/18/20/21/25mm
Poplar / Eucalyptus / Birch / Pine / Combi
BS EN 314-2 / BS EN 315 / BS EN 316 / BS EN 636
500-700 kg/m³
8%-12%
WWW.PIANOPLYWOOD.COM
Customizec Size & Thickness & Diameter
Environmentally friendly
CIRCULAR FILM FACED PLYWOOD
PIANOPLYWOOD
DIAMETER
PRODUCT CERTIFICATE
PEFC
FORMAT SIZE
LENGTH
THICKNESS & DIAMETER
MATERIAL
STANDARD
Free samples&prompt delivery
Prov. cust. logo&design
300-3000 mm× 1000-3000 mm× 14-18 mm /20-22 mm
300-3000 mm
1000×3000 mm
14-18 mm & 300-1200 mm / 20-22 mm & 1200-3000 mm
Poplar / Eucalyptus / Birch / Pine / or Other hardwood
BS EN 314-2 / BS EN 315 / BS EN 316 / BS EN 636
WWW.PIANOPLYWOOD.COM
RobertWang@pianoplywood.com
High standards&quality
Fax/Tel: +86-21-50792750
Casting up to 30 times
Customized size&thickness
Free samples&prompt delivery
Customized multiple colors
Eco-friendly&visualization
FORMAT SIZE
LENGTH
1220×2440 mm(4'×8')/1250×2500 mm
1525/1830/2135/2400/2440/2500/3000/3050 mm
WIDTH
THICKNESS
STANDARD
DENSITY
MOISTURE CONTENT
610/915/1200/1220/1250/1500 /1525 mm
6-35 mm
BS EN 314-2 / BS EN 315 / BS EN 316 BS EN 636 / EN 13353
500-680 kg/m³
8%-12%
WWW.PIANOPLYWOOD.COM
RobertWang@pianoplywood.com
MDO
PIANOPLYWOOD
FILM FACED PLYWOOD
PRODUCT CERTIFICATE
Environmentally friendly
Customized size&thickness
FORMAT SIZE
THICKNESS
LENGTH
WIDTH
STANDARD
DENSITY
Free samples&prompt delivery
High waterproof
1220×2440 mm/1250×2500 mm
9-25 mm
1830/2440/2500/3000 /3050 mm
610/915/1220/1250/1500/1525 mm
BS EN 314-2 / BS EN 315 / BS EN 316 BS EN 636 / EN 13353
500-530 kg/m3
WWW.PIANOPLYWOOD.COM
Visualization
RobertWang@pianoplywood.com
High standards&quality
ORIENTED STRAND BOARD
PIANOPLYWOOD
PRODUCT CERTIFICATE
Environmentally friendly
Customized size&thickness
FORMAT SIZE
LENGTH
WIDTH
Free samples&prompt delivery
High waterproof
1220×2440 mm/2100×280 mm/1830×2440 mm
THICKNESS
2440 /2800 mm
1220/1830/2100 mm
9-25 mm
STANDARD
SURFACE DESIGN
APA PS1-95 / ANSI 117 / ANSI A190.1
ANSI/APA RPG 320 / ANSI 405 / EN314-2
Melamine paper(glossy / matt / embossed etc.) Beech / Oak / Walnut / Maple / Teak / Cherry / Lvory or as request
WWW.PIANOPLYWOOD.COM
Visualization
High standards&quality
RobertWang@pianoplywood.com
OSB-ORIENTED STRAND BOARD
PRODUCT OSB-Oriented Strand Board
OSB sheathing panels provide dimensional stability and stiffness for wall and roof sheathing applications. These panels have strong and uniform consistency throughout. Plus, they have a blue edge seal that helps prevent moisture-related issues such as edge swell.
•Every piece meets the highest grading standards for strength and appearance •No core voids, knots, or splits
•Multi-layered bonding provides exceptional dimensional stability and stiffness •Panels offer strength, racking and impact resistance, and uniformity
| Format | 2500*1250,2440*1220mm ,(customizable according to requirements)9,12,15,18mm ,(Customizable according to reuirements) |
| Thickness | |
| Emission Class | E1 (EN ISO 12460-5) |
| certificate | FSC/CE/CARB/ISO 9001 |
| standard | EN 300-type OSB 3/EN 13501-1:class B-s1,d0/EN 13986:2004+A1:2015 |
| Application | 1.Structural applications:walls,floors,roofs,staircases,hoardings, 2.Interior:furniture elements,decorative elements inindoor spaces,framework in upholstered furniture,door panels,claddings and partition walls , 3.Packaging:shipping boxesand containers,pallets, 4.Retail & exhibitions,5.Warehouse management(shelving,racking,etc.) |
RobertWang@pianoplywood.com
OSB-ORIENTED STRAND BOARD
OSB 2 is developed and manufactured entirely in compliance with the current demand of ecological living focused on organic materials. Selecting suitable wood and binder, OSB 2 meets high standards of not only environmental buildings.
OSB 3
OSB 3 is the most progressive OSB type that is currently available. OSB 3 is developed and manufactured entirely in compliance with the current demand of ecological living focused on organic materials. Selecting suitable wood and binder, OSB 3 meets high standards of not only environmental buildings.
Fax/Tel: +86-21-50792750
RobertWang@pianoplywood.com
PHN/WA/WX: +86-133 1189 1208
PRESSURE TREATED TIMBER
PIANOPLYWOOD
PRODUCT CERTIFICATE
Corrosion resistance
Customized size&thickness
LENGTH
Free samples&prompt delivery
High waterproof
Up to 12000 mm
WIDTH
Visualization
50 /75/100/125/150/175/200/225/250/300 mm
THICKNESS
MATERIAL
TREATMENT AGENT
High standards&quality
PROCESS
47 / 75 / 100 mm
Douglas fir / Spruce / Fir / Radiated pine / Larch / Mongolian pine / Birch / Ash/ Basswood / Walnut / Cherry / Oak / Southern yellow pine
CCA /ACQ / CA-B / CBA /Cu8 / CuN / BAC / Cu+DDAC / Arsenic / Permethrin / Cypermethrin / Deltamethrin / Creosote / Bifenthrin / TBTO Or TBTN
Pressure treated / Carbonized
WWW.PIANOPLYWOOD.COM
RobertWang@pianoplywood.com
CE
| Use category | Use condition | Use environment | Main biological wood-destroying agencies | Typical use | |
| C1 | H1 | Indoor; kept clearof soil | Used in indoor dry environment; free of effect from weather andmoisture | Moth | Building interior, decorationand furniture |
| C2 | H2 | Indoo; kept clearof soil | Used in indoor environment,sometimes under the effect ofmoisture but free of weather effect | Moth,termite and wood-destroying fungi | Buildinginterior,decoration,furniture,basement and toilet |
| C3 | H3 | Outdoor; keptclear of soil | Used in outdoor environment and exposed to variousweathers,including shower but not immersed in water for a longterm | Moth,termite and wood-destroying fungi | Deck(of platform,walkway andtrestle),outdoor furniture andexterior door and window(ofbuilding) |
| C4A | H4 | Outdoor;exposedto soil orimmersed in freshwater | Used in outdoor environment,exposed to various weathers,andcontacted with the ground or immersed in fresh water for a longterm. | Moth,termite and wood-destroying fungi | Fence column,support,woodenhouse foundation,coolingtower,electic pole andjamb(pitprop) |
| C4B | H5 | Outdoor ;exposedto soil orimmersed in freshwater | Uesd in outdoor environment,exposed to various weathers,andcontacted with the ground or immersed in fresh water for a longterm.Structural component which is difficult to replace or thecrutucal one. | Moth.termite and wood-destroying fungi | (Fresh water)Pier fender,pileand jamb(pitprop) |
| C5 | H6 | Lmmersed inseawater(saltwater) | Lmmersed in seawater(salt water)for a long term. | Marine boring animal | Seawater(salt water)pierfender,pile and wooden boat |
| Length | Up to 12 meters(customized according to requirements) |
| Width/thickness | Customizable according to reuirements |
| Treatment agent | CCA/ACQ/CA-B/CBA/Cu8/CuN/BAC/Cu+DDAC/Arsenic/Permethrin/Cypermethrin/Deltamethrin/Creosote/Bifenthrin/TBTO or TBTN |
| Standard | H2F/EN-350-2-1994 |
| Material | Pine/Radiata Pine/Red pine/Larch/fir/spruce/southern pines/Douglas fir/ Hemlock/Mason pine1.Anticorrosive wooden flower racks and boxes;2.Anticorrosive wooden corridor,3.Anticorrosive wood flooring,4.Anticorrosive wooden tables and chairs,andanti-corrosion wooden stools |
| Application |
PHN/WA/WX: +86-133 1189 1208
RobertWang@pianoplywood.com
www.pianoplywood.com
PIANO
PianoPlywood
CHINESE BUILDING MATERIAL EXPERT, ONE STOP SERVICE PROVIDER
WWW.PIANOPLYWOOD.COM
Fax/Tel: +86-21-50792750
Phone/WhatsApp/WeChat: +86-133 1189 1208
E-mail: RobertWang@pianoplywood.com
Add: Block F,Floor 8,NO.58,New Jinqiao RD,Pudong District,Shanghai 201206,China
WWW.PIANOPLYWOOD.COM
PianoPlywood
Fax/Tel: +86-21-50792750
Phone/WhatsApp/WeChat: +86-133 1189 1208
E-mail: RobertWang@pianoplywood.com
Add: Block F,Floor 8,NO.58,New Jinqiao RD,Pudong District,Shanghai 201206,China
