该页无缩略图
DEMOLITION HAMMER
MACHINEPARTS
| 5001 |
| Rated InputPower 输入功率 1500 W |
| ImpactTimes 冲击频率 1100-2150 bpm |
| NetWeight 重量 10 kg |
5001 零件表
| NO. | NAME | QTN NO. | NAME | QTN | |
| 50.GEARBOX | 齿轮箱 1 | 100.ROTOR | 转子1 | ||
| 51.SEALING COVER 齿轮箱加油密封盖 | 1 | 101.STATOR | 定子 1 | ||
| 52. | O-RING35x1.9 加油密封盖0型圈 | 1 | 102. | COPPER | 铜簧 2 |
| 53. | BRAND | 商标 1 | 103. | LINE | 刷握接插线 1 |
| 54. | BUTTON 调档旋钮 | 104. | PLASTICGASKET | 机壳定子塑料垫 1 | |
| 55 | O-RING19.6x2.4 调档0型圈 | 1 | 105. | GASKET | 防尘塑料垫片 1 |
| 56. | IRONCORE 调档铁芯 | 1 | 106.BEARING 6000 | 6000轴承 1 | |
| 57. | BUTTONPIN①4X10.7 调档按钮销 | 107.GEAR HOUSING | 机壳 1 | ||
| 58. | SPRING 调档弹簧 | 1 | 108. | SMALLPLASTICCOVER | 机壳小塑料盖 1 |
| 59. | BUTTON 调档按钮 | 1 | 109. | BRAND | 商标 1 |
| 60. | SMALL BEVEL GEAR 小锥形齿轮 | 1 | 110. | SWITCH SPEED PLATE | 开关调速板 1 1 |
| 61. | BEARING 6201RZ 轴承 | 2 | 111. | RETAINER | 开关调速板压板 |
| 62. | WASHER12×23.7×1 6201轴承垫片 | 2 | 112. | FAN | 风叶 |
| 63. | POSITIONKEY 离合器定位销 | 7 | 113.FLATWASHER M88.3x14.7x1 | 平垫片 1 | |
| 64. | SPECIALLOCKING NUT 特殊锁紧螺母 | 1 | 114.HEXNUT | M8六角螺母 1 1 | |
| 65. | SPRING WASHER 碗型弹簧垫片 | 2 | 115. | BUTTON COVER | 底盖 |
| 66. | CLUTCHRETAINER 离合器压板 | 1 | 116. | BRUSH HOLDER COVER | 刷握盖外罩 2 |
| 67. | 52DENSCLUTCHGEAR52牙离合斜齿轮 | 1 | 117. | RUBBER GRAIN | 刷握盖外罩橡胶粒 2 |
| 68. | CLUTCH 离合器 | 1 | 118. | BRUSH HOLDER | 刷握盖 2 |
| 69. | POSITIONBALL6X6 离合器定位钢珠 | 6 | 119. | CARBON BRUSH | 碳刷 2 |
| 70. | WIREBALLC6 钢珠C6 | 6 | 120.CARBONBRUSH HOLDER | 碳刷握（左右） 1 | |
| 71. | RING12 轴用挡圈12 | 2 | 121.HANDLE | 手柄 1 | |
| 72. | SPECIALPOSITIONKEY 特殊定位键 | 2 | 122. | SWITCHREDBUTTON | 开关红按钮 1 |
| 73. | WASHER12×27.8x1 定位键垫片 | 123. | SWITCH | 开关 1 | |
| 74. | POSITIONKEY 调档拨叉定位销 | 124.HANDLE COVER | 手柄盖 1 | ||
| 75. 76. | FORKKNOB 调档拨叉小方块 | 1 1 | 126.SWITCHCLAMP | 开关压线夹 1 | |
| 77. | SPRING 调档拨叉弹簧 | 127.PROTECTIVESLEEVE | 护套 1 | ||
| 78. | SPRING 调档拨叉弹簧销 SELECTORFORK 调档拨叉 | 1 | 129. | 128.CABLE2x1.5mm/4m | 电线 |
| 79. | BEARING608 608轴承 | 1 | 130. | CABLECLAMP | 压线板 1 1 |
| 80. | WASHER15.3x20x0.2 608轴承垫片 | 1 | DEPTH GUAGE | 标尺 | |
| 81. | ECCENTRICGEAR 偏心轴 | 1 | 132. | 131.HANDLE IRONRING | 手柄铁圈 1 |
| 82. | FLATKEY5x5x15.2 平键 | 2 | LONGBOLTM8x81 | 长螺栓 1 | |
| 83. | BEARINGWASHER62/32 轴承垫片 | 1 | 133.BOLTWASHER | 螺栓垫片 1 | |
| 84. | BEARING 62/32轴承 | 1 | 135. | 134.NUTM6 | 螺母 1 |
| 85. | RETAINERRING65 孔用挡圈65 | 1 | 136. | BUTTON HANDLE SEAT | 标尺螺丝旋钮 1 手柄座 |
| 86. | 50DENSSLANTINGGEAR 50牙斜齿轮 | 1 | 137. | AUXILIARYHANDLE | 1 辅助手柄 1 |
| 87. | FLAT KEY 4x4x10 平键 | 2 | 138. | HEXB0LTM8x150 | 六角头螺栓 1 |
| 88. | 20DENSSLANTINGGEAR20牙带键斜齿轮 | 1 | 139. | AUXILIARYGRIPBASE | 副手柄座（框型） 1 |
| 89.RING14 轴用挡圈14 | 1 | 140.LOCKNUT | 锁紧螺母（带嵌件） 1 | ||
| 90. | WASHER20 20牙斜齿轮垫片 | 2 | 141. | ALUMINIUMGRIPBASE | 铝手柄座 1 |
| 91. | DENS SLANTING GEAR20 牙斜齿轮 | 1 | 142. | SCREWST6.3x37内六角圆柱头自攻螺钉 | 4 |
| 92. | NEEDLEBEARINGHK1210 滚针轴承 | 1 | 143. | 3 | |
| SCREWST3.8x14 十字盘头自攻螺钉 | |||||
| 93. | SEALING RING 齿轮箱密封圈 | 144. | SCREWM6x25内六角圆柱头螺钉（带弹垫） | 4 | |
| 94. | POSITIONKEY 齿轮箱定位销 | 1 | 145. | HEXSCREWST4.8x54十字槽六角头螺钉 | 2 |
| 95.NEEDLEBEARINGHK1212 滚针轴承 | 1 | 146.HEXAGONSCREWM5×10内六角圆柱头螺钉 | 2 | ||
| 96. | POSITIONKEY 齿轮箱盖固定销 | 1 | 147.SCREWST4.2x16 | 十字盘头自攻螺钉 4 | |
| 97. | GEAR BOX COVER 齿轮箱盖 | 1 | 148. | SCREWST5×23 | 十一字盘头自攻螺钉 |
| 98. | OLISEAL14x32x7 | 油封 1 | 149. | SWITCHINSERTLINE | 4 开关接插线 |
| 99.BAFFLE PLATE | 挡风板 1 | 150.SCREWST6.3x22内六角圆柱头自攻螺钉 | 1 4 |
ORINGS
| Product No. | Product Name | Model | Size(mm) |
| 10803034 | O ring-piston(F) | 0810 | 23.5x3.5 |
| 115007158 | O ring-striker(F) | 0810 | 23.2x3.5 |
| 115007192 | O ring-X RING(F) | 0810 | 27.5x36x6.6 |
| 115007139 | O ring-tool holder(F) | 0810 | 27.5x3.5 |
| 115007194 | O ring-oil cap | 0810 | 60x2 |
| 10803030 | O ring-piston(F) | PH65A | 32x45.1x7 |
| 115008132 | O ring-barrel | PH65A | 60x2 |
| 115008115 | O ring-oil gauge | PH65A | 19.8x2.1 |
| 115004135 | O ring-piston(F) | 2-26 | 15x3 |
| 115004193 | O ring-aluminum flange | 2-26 | 52.5x7.4 |
| 115001097 | O ring-piston/striker(F) | 2-20 | 14x3 |
| 115001073 | O ring-aluminum flange | 2-20 | 62x3 |
| Product No. | Product Name | Model | Size(mm) |
| 115001095 | o ring-outside knob | 2-20 | 6x2.2 |
| 10803033 | o ring-piston(F) | 11E | 30x5 |
| 115009119 | o ring-tool holder | 11E | 31.5x2.5 |
| 10803040 | o ring-piston(F) | 0835 | 28.4x3.5 |
| 115040034 | o ring-piston(F) | GSH388 | 29.8x22.2x4.08 |
| 115040044 | o ring-striker | GSH388 | 24x3.2 |
| 115015085 | o ring-tool holder | 1201 | 33.7x3.5 |
| 115015082 | o ring-piston(F) | 1201 | 30.2x5.1 |
| 115015106 | o ring-oil cap | 1201 | 71x2 |
| 115010078 | o ring-piston(F) | 3-26 | 19x3.1 |
| 108234 | o ring-tool holder | 3-26 | 19.8x2.1 |
| 1S0010ST Ohgpiston/stnker(1) 220 14X5 106254 omg-toormoaer | |||||||
| 115001073 O ring-aluminum flange 2-20 62x3 | |||||||
| No. | Specifications(mm) | No. | Specifications(mm) | No. | Specifications(mm) | No. | Specifications(mm) |
| 1 | 1.8x1.8 | 26 | 26.4x4.4 | 51 | 51.3x2 | 76 | 78x3 |
| 2 | 2x1.8 | 27 | 27.5×3.5 | 52 | 52.2×7.4 | 77 | 79×1.5 |
| 3 | 3.8x1.9 | 28 | F28.4×3.5 | 53 | 53.2×2.3 | 78 | 80×2.0 |
| 4 | 4.5×3.7 | 29 | 29.4×x3.1 | 54 | F54.5×2.2 | 79 | 81x2 |
| 5 | 5.5x1.05 | 30 | 30×2 | 55 | 55x3 | 80 | 82.5×1.5 |
| 6 | 6x2.5 | 31 | 31.5 ×2 | 56 | 57x3 | 81 | 83×1 |
| 7 | 7x2 | 32 | 32×2.5 | 57 | 58×2.4 | 82 | 85×3.1 |
| 8 | 8x2 | 33 | 33.2×2 | 58 | 59×5.6 | 83 | 86x2.1 |
| 9 | 9x3.5 | 34 | 34.5×2.65 | 59 | 60×6 | 84 | 88x2 |
| 10 | 10x3 | 35 | 35×2 | 60 | 61x4.8 | 85 | 89.5×2(90×2) |
| 11 | 11x2 | 36 | 36×2 | 61 | 62x3 | 86 | 92×3.1 |
| 12 | 12.5×1.5 | 37 | 37×1.5 | 62 | 63.5×3.3 | 87 | 93.5×2 |
| 13 | 13×3 | 38 | 38×2.5 | 63 | 64x6.3 | 88 | 94x3.55 |
| 14 | 14×2(14.3×2) | 39 | 39.4x3.1 | 64 | 65.5×3 | 89 | 95×3 |
| 15 | 15x2 | 40 | F40×2 | 65 | 66x3 | 90 | 97×3 |
| 16 | 16.1x4.5 | 41 | 41.5×2 | 66 | 67.5x7 | 91 | 98×2.5 |
| 17 | 17.5x2 | 42 | 42×1.5 | 67 | 68x3 | 92 | 105×1.2 |
| 18 | 18×3.5 | 43 | 43x1 | 68 | F69x3.5 | 93 | F107 x3.1 |
| 19 | 19.4×3 | 44 | 44×2 | 69 | 70×5 | 94 | 110×3.1 |
| 20 | 20.2x3 | 45 | 45×5 | 70 | 71x2 | 95 | 113x3.1 |
| 21 | 21.5×1.8 | 46 | 46.8x2.5 | 71 | 72x3 | 96 | 206x3.5 |
| 22 | 22×4 | 47 | 47.5×2 | 72 | 73x2 | 97 | 209×3.5 |
| 23 | 23.5×2.4 | 48 | 48x2 | 73 | 74×2.5 | 98 | 211 ×3.5 |
| 24 | 24.5x1.6 | 49 | F49.3×3.5 | 74 | 75x2.65 | ||
| 25 | 25×2 | 50 | 50×5 | 75 | 77×2 | 10 | |
OILSEAL
| 外径 | |||
| 轴径 | |||
| Product No. | Product Name | Model | Size(mm) |
| 115007171 | oil seal | 0810 | 30x16x6 |
| 115006025 | oil seal-front head | 2470 | 25x35x7 |
| 115001074 | oil eal | 2-20 | 28x37x8 |
| 115004146 | oil seal | 2-26 | 8x16x5 |
| 115004192 | oil seal | 2-26 | 30x41x7 |
| 108237 | oil seal | 2-26 | 35x51x6 |
| 115040051 | oil seal | GSH388 | 38x50x7 |
| 115040064 | oil seal | GSH388 | 12x30x7 |
| 115009188 | oil seal | 11E | 32x42x7 |
| 115009123 | wool oil seal | 11E/GWS20-180/230 | inner hole-19mm |
| 115012087 | oil seal | H41 | 19.8x35x5 |
| 108194 | oil seal | 25901 | 18x28x7 |
| No. | Specifications(mm) | No. | Specifications(mm) |
| 1 | 6x12x3 | 39 | 32×42×7 |
| 2 | 8×16×5 | 40 | 34×43×7 |
| 3 | 9×16x5 | 41 | 35×47.2×6.5 |
| 4 | F10×18×4 | 42 | 37×76×10 |
| 5 | 11×16×3.2 | 43 | 38×55×8 |
| 6 | 12 ×22×4.5 | 44 | 40×65×10 |
| 7 | 13.5×26.5×2.5 | 45 | F41×53×7 |
| 8 | 14×22×4 | 46 | F42×58x8 |
| 9 | F15×25×4.5 | 47 | 45×60×9 |
| 10 | 16×22×3 | 48 | 46×64×7 |
| 11 | 17×23×4 | 49 | 50×62x6 |
| 12 | 18×24×3 | 50 | 60×90×10 |
| 13 | 19×24.3×3.6 | 51 | F65×90×7 |
| 14 | 20×32x6.3 | 52 | F66x96×10 |
| 15 | 22×28×4 | 53 | 70×90×10 |
| 16 | 23.4×40×6.8 | 54 | 75×102×10 |
| 17 | 24×33×7 | 55 | 80×100×10 |
| 18 | 25×34x5 | 56 | 100×125×12 |
| 19 | 26×34x4 | 57 | 105×130×12 |
| 20 | 27×37x6.5 | 58 | 120×150×12 |
| 21 | 28×37×8 | 59 | 145×175×14 |
| 22 | 30×45x5 |
| Items品种 | S/N 序列号 | MODEL型号 | CNT/QTY | QTY | PACKAGE |
| 1.A/B WASHER压板 | |||||
| A/B washers 压板 | 116092 | CM4SA/SB | 400 | pouchpackingmidle ox | |
| 116095 | GWS6-100 | 600 | pouch packing+midle box | ||
| 116096 | Dw801 origal) | 600 | Douch packingmidle box | ||
| 116097 | F3/G10SS | 600 | pouch packingmidle box | ||
| 116093 | MT410 | 400 | pouch packing+middlebox | ||
| 116298 | C7 | 400 | pouch packing+middle box | ||
| 116211 | GDC34 | 400 | pouch packingmidle box | ||
| 116098 | GWS20-180 | 200 | Houch ackingmidle ox | ||
| 116185 | GA7020 | 200 | ouch packingmidle ox | ||
| 116101 | G15SA2 | 200 | pouch packing+middlebox | ||
| 116103 | LG355 | ||||
| CM4SA | 600 | pouch packingmidle box | |||
| SPINDLES 输出轴 | 132013 | ||||
| 132014 | CM4SB | 600 | pouch packing+middlebox | ||
| 132015 | Dw801 (old) | 600 | pouch packingsmidle box | ||
| 132020 | MT410 | 600 | pouch packing+middlebox | ||
| 132021 | 9553NH | 600 | pouch packingmiddle box | ||
| 132022 | G10SS | 600 | pouch packing+middlebox | ||
| 132129 | GWS6-10 801New) | 600 | pouch packing+middlebox | ||
| 132029 | PD100M | 600 | pouch packing+middlebox | ||
| 132017 | PD100D PD100D125mm | 600 | pouch packing+midle box | ||
| 132105 | CMS | ||||
| 132042 | 320 | pouch packing+midle box | |||
| 132059 | CM6 | 320 | pouch packing+middlebox | ||
| 132036 | EID13 | 200 | pouch packing+midle box | ||
| 132069 | 13RE | 200 | pouch packing+middlebox | ||
| 132041 | FF-160 | 200 | pouch packing+midle box | ||
| 132019 | G15SA2 | 320 | pouch packing+middlebox | ||
| 132024 | G18SE2 | 200 | pouch packing+middlebox | ||
| 132034 | G18SC | 200 | pouch packing+middlebox | ||
| 132047 132028 | gws20-180(1351) GA7020 | 200 200 | pouch packing+middlebox | ||
| 132025 | LG355 | pouchpackingmidle ox | |||
| 160 | pouch packing+middlebox | ||||
| 132040 | C7 | pouch packing+midle box | |||
| 132065 132113 | DCA6.5A | pouch packing+middlebox | |||
| 7614NB | pouch packing+midle box | ||||
| Spanner 扳手&砂轮罩 | 110057 | CM4SA 2.5mm thinkness GWS6-10/801new | 300 | pouch packing+midle box | |
| 110045 | 480 | ouch aeckingmnidle o x | |||
| 110056 | 6-100- H | 480 | pouch packing+middlebox | ||
| 110050 | 9553 | 480 | pouch packing+middle box | ||
| 110044 | Dw801(22mm) | 480 | pouch packingtmiddlebox | ||
| 110058 | DW801 - H(22mm) | 480 | pouch packing+middlebox | ||
| 110079/10077 | MT410(bes/nomal | 300 | pouch packingmidle box | ||
| 110049 110047 | G15SA2 (should match DCA size) | 300 | pouch packing+middlebox | ||
| 110062 | GWS20-180 | 360 360 | pouch packing+middlebox | ||
| 4.Wheel Guard 砂轮罩 | GA9020 | pouch packing+midle box | |||
| Wheel Guard 砂轮罩 | |||||
| 118060 118059/118071 | GWS6-100/801new | 200 | Foam Packing +carbon box | ||
| Dw801 (old/ 15mm) | 200 | Foam Packing +earbon box | |||
| 118061 118046 | GWS7-115new | 200 | Foam Packing +carbon box | ||
| 118047 | GWS20-180 GWS20-230 | 50 50 | Foam Packing +carbon box | ||
| GA7020 (9067) 180MM | 50 | Foam Packing +carbon box | |||
| 118049 | Foam Packin +carbon box | ||||
| 118050 | GA9020/ (9069) 230MM | 50 | Foam Packing +carbonbox | ||
| 118045 118056 | PD100D/F3 | Foam Packing +carbon box | |||
| G18SE2(180MM) G18SE2(230mm) | Foam Packing +carbon box Foam Packing +carbon box | ||||
| 5.MOTORHOUSING机壳 | 118066 | 6-125(125MM) | Foam Packing +carbon box | ||
| 10603201 | 6-100 completehousing | 100 | pouch packing+Carton box | ||
| 10603192 | 953 complete housing | 100 | pouch packing+Carton box | ||
| 10603138 | Dw8o1complet ousing | 100 | pouch packing+Carton box | ||
| 115007199 | 0810T housing | 50 | pouch packing+Carton box | ||
| 115007202 10603125 | 0810T Switch handle | pouch packing+Carton box |
| PARTS | IE swith handle | ||||
| 115009189 10604007 | LG355 switch handle | 30 80 | pouch packing+Carton box pouch packing+Carton box | ||
| 10603090 | CMSA housing | 50 | pouch packing+Carton box | ||
| CM4SB housing | 50 | pouch packing+Carton box | |||
| 10603115 | G15SA2 body | 100 | pouch packing+Carton box | ||
| 10603202 | G15SA2 switch handle | 150 | pouch packing+Carton box | ||
| 10604008 | |||||
| 115008184 | PH65A switch handle | 100 | pouch packing+Carton box | ||
| 115008186 | ph65A Switchhandle(Highquality) | pouch packing+Carton box | |||
| 115008178 | PH65A switch handle aluminum) 2-20 head cover with earing | 100 | pouch packing+Carton box | ||
| 115001091 115001107 | 2-20 body +cover | 80 | pouch packing+Carton box | ||
| 115004128 | 2-26 head cover | 100 | pouch packing+Carton box | ||
| 115004143 | 2-26 head cover with bearing | ||||
| 115004178 | 2-26 body+coverwithoutwordhole | ||||
| 115004142 | 2-26 body + cover with word hole | 80 | pouch packing+Carton box | ||
| 6.GEARBOX&ALUMINIUM | |||||
| GWS6-100 Bearing Housing | 320 | pouch + sticker | |||
| 1052084 1052184 | GWS6-100 PVC with bearing 6201 | pouch+sticker | |||
| 105083 | GWS6-100Completeset | 100 | COLORBOX+CARBONBOX | ||
| Dw801 Bearing Housing | 320 | pouch + sticker | |||
| 1052083/1052111 | Dw801Completeset | 100 | COLOR BOX+CARBON BOX | ||
| 105078 | 95539554 Bearing Housing | 320 | |||
| 1052097 | 955/9554Complete set(3pcs) | 100 | pouch + stiker | ||
| 105085 | G10SS Bearing Housing | 320 | COLOR BOX+CARBON BOX | ||
| 1052090 | G10ss Housing PVC with bearing 6201 | pouch + sticker | |||
| 1052139 | G10ss2PVC with bearing 6201 | pouch + stickr | |||
| 1052140 | G10SSCompleset | 100 | pouch + sticker | ||
| 105080 | PDA100D Complte se (3pcs) | 100 | COLOR BOX+CARBON BOX | ||
| 105082 | PDA100D Complete set (2pcs) | COLOR BOX+CARBON BOX | |||
| 1052030 | PDA100M Bearng housing | 320 | COLOR BOX+CARBON BOX | ||
| 1052089 | PDA100M Complete set | 100 | pouch + sticker | ||
| 105095 | GW10-125 PVC wih bearing 6201 | 320 | COLOR BOX+CARBON BOX | ||
| 1052098 | GWS10-125Completeset withbearing | 100 | pouch + stiker COLOR BOX+CARBON BOX | ||
| 1052143 | G15SA2 Complete set | 50 | COLOR BOX+CARBON BOX | ||
| 105088 | CMSA Bearing Housing | 400 | |||
| 1052087 | CM4SA Complete set | 50 | pouch + sticker | ||
| 1052226 1052085 | CM4SB Bearing Housing | 400 | COLOR BOX+CARBON BOX | ||
| CM4SBComplete set | 50 | pouch + sticker | |||
| 1052134 | GBH2-20 Flange with bush & O ring | 100 | COLOR BOX+CARBON BOX | ||
| 115001112 | COLOR BOX+CARBON BOX | ||||
| 115004215 1052070 | GBH2-26 Flange with bush & O rng o810TCcomplteset | 100 | COLORBOX+CARBON BOX | ||
| 115009201 | GSH11E Gearbox | 50 15 | COLOR BOX+CARBON BOX | ||
| 7.GEAR&PINION齿轮 GEAR SET | GSHI1E Gearbox with metel ring need | 15 | Brown BOX+CARBON BOX Brown BOX+CARBON BOX | ||
| 115009136 | |||||
| 104536 | CM4SA | 300 | poueh+midle ox | ||
| 104454 | CM4SB | 300 | Douch-msidle o | ||
| 104455 | MT410 | 300 | |||
| MT412 | pouch+midle box | ||||
| 104603 | GDC120 | 300 | pouch+midle box pouch+midle box | ||
| 104507 104464 | GDC34 | 300 | pouch+midle box | ||
| 104456 | 0810T | 100 | pouch+midle box | ||
| 104763 | LG355 | 100 | pouch+midle box | ||
| 104466 | GCO200 | 100 | pouch+midle box | ||
| 104472 | GCO200 | pouch+midle ox | |||
| 104482 | 2414NB | 100 | pouch+midle box | ||
| 104561 | MT580 | pouch+midle box | |||
| 104679 | MT60 | pouch+midle box | |||
| 104478 | CM5(NEW) | pouch-midle ox | |||
| 104671 | C7 With sot | pouch-midle box | |||
| 104524 | 5791 | pouch+midle box | |||
| 104489 | 11E Crank gear | pouch+midle box | |||
| 104469 | CC14SF | 100 | pouch+midle box | ||
| 104629 | CC14STD | 100 | pouch+midle box | ||
| 104495 | 322(same DW2810) | 100 | pouch+midle box | ||
| MT240 | 100 | pouch+midle box | |||
| 104470 104467 | ow871 | 100 | pouch+midle box | ||
| 104468 | DW28700 | ||||
| 104495 | 100 | pouch+midle ox | |||
| 104483 104715 PH65A SMALL GEAR | ow28710 DW28720 | 100 100 | pouch+midle box pouch+middle box | ||
| GBH2-20 Helical gear | |||||
| 115001119 115004111 | GBH2-26 Shaf gear | 600 640 | pouch-midle box pouch-midle box | ||
| GBH'2-26 Helical Gear 3theth | pouch-midle box | ||||
| 115004115 | 2-26 Shat Gear+Bearing699+Clamping | 400 | pouch+middle box | ||
| 115004189 | 2310 | 300 | pouch-midle box | ||
| 104465 | ED-6 (HITACHI 6.5MM) | 300 | pouch-midle box | ||
| 104460 | FF-10A平板齿 | 240 | pouch-midle box | ||
| 104661 | pouch-midle box | ||||
| 104477 | GSB13RE冲击齿(same oringal) | 240 240 | pouch-midle box | ||
| 104457 | DU-10 3pes/set) o-10 2peset | pouch+middle box | |||
| 10-46-48 | EID13 3pcs/set) | 240 | pouch-midle box | ||
| 104458 104442/104444 | GWS6-100(good/normal) | 240 | pouch+middle box | ||
| 104535 | GWS6-100straight gear | 240 | pouch-midle box | ||
| 104450 / 104775 | DW801 god/normal) | 240 | pouch-middle box | ||
| 9553/9554 (g0od/normal) | 240 | pouch-midlebox | |||
| 104757 /104759 | G10SS | 240 | pouch-midle box | ||
| 104436 | PD100D | 240 | pouch-midle box | ||
| 104451 | PD100M | 240 | pouch+midle box | ||
| 104437 | GWS7-100(GWS7-115 NEW) cnc Hig | pouch-midle box | |||
| 104538 | 240 | ||||
| 104782/104780 | G1 5SA2 (good/normal) | 100 | pouch+middle box | ||
| 104500 | G18SE2 CNC high quality GWS20-180(1351 3Holes CNChigh | 50 | pouch-middle box | ||
| 10-4498 | 50 | pouch-midlebox | |||
| 104592 | GWS20-230 (1361 4Holes CNChigh GA7020 CNC high quality | 50 | pouch-midlebox | ||
| 104554 | GA9020 CNC high quality | 50 50 | pouch-midle box | ||
| 104512 | DW28490 CNC high quality | pouch-midle box pouch-midle box | |||
| 104766 | DW28491 180M) CNC high qality | 50 | pouch-midle ox | ||
| 104733 | DW28493 (230MM) CNC high quality | 50 | pouch-middle box | ||
| 8.CYLINDER/PISTON铝活塞 | 11500112 | GBH2-20 | 600 | pouch-midlebox | |
| 115004117 | GBH2-26 | 600 | pouch-midlebox | ||
| GHB2-24 | 600 | pouch-midle box | |||
| 115003134 | GBH2-22 | 600 | |||
| 115002040 | pouch-middle box | ||||
| 115030002 115005043 | GBH2-28 HR2450 | 600 | pouch-midle box | ||
| 9.SWITCH | HR2470 | 600 600 | pouch-midle ox pouch+middle box | ||
| 1 | 115006081 | ||||
| 107939 | GBH'2-20 Variable | 500 | pouch.clor box | ||
| 107630 | GBH2-20 (Single speed) | pouch.color box | |||
| GBH'-26 | 500 | ||||
| 107614 | HR2450 | 500 | pouch. color box | ||
| 107568 | pouch,color box | ||||
| 107632 | 2470 withou itht | 500 | pouch. color box | ||
| 107801 | 13RE | 320 | pouch, color box | ||
| 107912 | CM4SA/ normal | 1000 | pouch,. color box | ||
| 107916 | CM4SAgood GDC34 | 1000 | pouch. color box | ||
| 107621 | 1000 | pouch. color box | |||
| 107593 | 1000 | ||||
| GWS6-100 (good/normal) | |||||
| 107930/107932 | 9523/PDA100/G10SS | 1000 1000 | pouch, color box | ||
| 107638 107611 | FF-160 old | 500 | pouch. color box | ||
| FF-160(NEW) | pouch, color box pouch, color box | ||||
| 107793 | FF-10A/SCREWDRIVER Variable | 500 | |||
| 107594 107558 | FF-10A/SCREWDRIVER Single speed | pouch. color box | |||
| 107651 | w871 | 500 | pouct, olor box pouch. color box | ||
| 107559 | CC14SF | 500 | pouch. color box | ||
| 107909 | LG355 | 500 | pouch. color box | ||
| 107647 | 5016 | 500 | pouch.color box | ||
| 107606 | 4107 | ||||
| 107597 | G15SA2 with metel plate | 500 | pouch. color box | ||
| G15SA2 Plasic plate | pouch. color box | ||||
| 107557 | GCO2000 | 500 | pouch.color box | ||
| 107640 | GCO200 | pouch. color box | |||
| 107560 | ED-6 (HITACHI 6.5MM) | 500 | pouch. color box | ||
| 107943 | 0810T with metel plate | 500 | pouch.color box | ||
| 0810t Plastieplate | |||||
| 107928 107566 | 590 wit lock | 500 | pouch. color box | ||
| 107572 | GBH 388 | 500 | pouch, color box pouch.color box | ||
| 107622 | GSB1300/6510 | 500 | pouch. colorbox | ||
| 107677 | 9227C HR1630/HR1620 | 500 500 | |||
| 9.CARBON SHAFT/Holder | 107889 PH65A Plastic plate | ||||
| 107816 | PH65A with rubber cover | pouch, color box | |||
| 107929 | GWS20-180 | 240 | pouch, color box | ||
| 107925/107927 | G18SH2/GA7020 | 240 | pouch, color box | ||
| 107917/107919 | G18SE2 | 240 | pouch, color box | ||
| 10.CARBON BRUSH CAP | pouch, color box | ||||
| 112326 | 13RE | 500 | pouch, color box | ||
| 115004137 | GBH2-26(Fllset | pouch, color box | |||
| 115001105/115001113GBH2-20 | |||||
| HR2470 | pouch, color box | ||||
| 112215 | 0810T Ful Coper) | pouch, color box | |||
| 112199 | 0810T (Empty copper) | pouch, color box pouch, color box | |||
| 112200 | PH65A (Full copper) | pouch, color box | |||
| 112201 112202 | PH65a (emptly copper) | pouch, color box | |||
| 112206 | LG35(Full coper) | pouch, color box | |||
| 112203 | CM4SA/CM4SB/G15SA2 Ffllcopper | pouch, color box | |||
| 112208 | PD100d/PD100m/G10ss | pouch, color box | |||
| 112355/112216 | GWS20-180 With2pcsSpring | pouch, color box | |||
| 112240/112253 | GWS6-100With 2Spring | pouch, color box | |||
| 112204/112226 | Dw801 With 2Spring | pouch, colorbox | |||
| 9553 with2 Spring | pouch, color box | ||||
| 112241/ 112198 112260 | FF-160(NEW) | pouch, color box | |||
| 112366/112333 | CC14STD | pouch, color box | |||
| 112292 | MT410 | pouch, color box | |||
| 112293 | 5016 | pouch, color box | |||
| 112297 | G18SE2 | pouch, color box | |||
| 115009191 | E | pouch, color box | |||
| pouch, color box | |||||
| 112264 | LG35518M | pouch, color box | |||
| CM4SA/CM4SB/G15SA2 M18*6mm | pouch, color box | ||||
| 11.CARBONBRUSH | 112219 112294 | G18SE2 M20 | pouch, color box | ||
| 112266 | 1900BM12 | pouch, color box | |||
| 115007164 | 0810T M14 | ||||
| 115008155 | 65A M20 | pouch, color box | |||
| pouch, color box | |||||
| M M | Model | Material Quality | PCS/CTN | ||
| Code 111160 | CM4SA | 660 | 1000 | ||
| 111084 | MT410/CB303 | 660 | 1000 | ||
| HM0810 | 1000 | ||||
| 111010 | 660 | ||||
| 11106 | LG355 | 660 | 1000 | ||
| 111012 | Dw801 | 660 | 1000 | ||
| 111013 | 6-10 | 660 | 1000 | ||
| 111138 | GBH2-20 | 660 | 1000 | ||
| 111073 | GBH2-26 | 660 | 1000 | ||
| 111067 | DU-10 | 660 | 1000 | ||
| 111245 | 9553/CB325 | 660 | 1000 | ||
| 111177 | 1900B/CB51 | 660 | 1000 | ||
| 111014 | 2310(YZ) | 660 | 1000 | ||
| 111207 | 2410/2510 | 660 | 1000 | ||
| 111243 | 35-1 | 660 | 1000 | ||
| 111314 | GDC120 | 660 | 1000 | ||
| 111007 IE | 660 | 1000 | |||
| 111087 | #21/PD100M | 660 | 1000 | ||
| 111074 | Dw871(with rubber) | 660 | 1000 | ||
| 111008 | DW28700 | 660 | 1000 | ||
| 111217 | 7614NB | 660 | 1000 | ||
| 111006 | 4107% CB153 | 660 | 1000 | ||
| 11104 | GWS20-180/GCO200/2000 | 660 | 1000 | ||
| 111005 | PH65A | 660 | 1000 | ||
| 12.GOVERNOR调速器 | |||||
| 134021 | IIE GOVERNOR | 240 | pouch, color box | ||
| 134027 | 9227CGOVERNOR普通yk | 500 | pouch, color box | ||
| 134014 | 4001 GOVERNOR | pouch, color box | |||
| 134026 | 5001GOVERNOR | pouch, color box | |||
| 134022 | 5201GOVERNOR | pouch, color box | |||
| GWS6-115 | pouch, color box pouch, color box | ||||
| 134015 | GWS14-125 | ||||
| 10801004/108010212510（聚氨酯）Orange colorwhite color | pouch (biserad 0.075usd) | |||
| 255mMiterSawOrangecolorwhitecolor | pouch (blister add 0.075usd) | |||
| 10801023 | ||||
| 10801019 | 1900B Rubbler Black color | pouch (blister add 0.075usd) | ||
| 2510 Rubber Black color | pouch (bliter ad 0.075ud) | |||
| 255mmMiter Saw (nubber Black color | pouch (blister add 0.075usd) | |||
| 14.NeedleBearing滚针 | 355mm Cut ofMachine(ruber)Black color | pouch (blister add 0.075usd) | ||
| 109124 | HK0709 | pouch. color box | ||
| 109123 | HK0810 | pouch, color box | ||
| 109135 | HK1010 | pouch, color box | ||
| 109133 | HK1210 | |||
| 109139 | HK0608 /2-20 | pouch color box | ||
| 109140 | HK0910 | pouch, clor box ponch. color box | ||
| 109151 | HK0808 | |||
| 109213 | HK0809 | pouch, color box | ||
| 109113 | NA4902 / 11E | pouch, color box | ||
| 109176 | NA4902 / 11E sloxless | ponch, color box | ||
| 109142 | HK0609 | |||
| 109144 | HK1212/0810T | pouch, color box pouch, color box | ||
| 115008158 | NK1820 /PH65A | pouch. color box | ||
| HK0908 /2-26 | ||||
| 115004151 | BK1210 / 0810 I.G. | pouch, color box | ||
| 109133 | pouch, color box | |||
| 116077 | ||||
| 35m1x1m 35mmx1.5m | BAG PACKAGE | |||
| O | 116078 | BAG PACKAGE | ||
| 116070 | ||||
| 16.DRILLCHUCK夹头 | ||||
| 117066018 | Chuck Keyless 10mm 3/8*24UNF | |||
| 117066029 | Chuck Keyless 13mm 3/8" | |||
| 117066059 | Chuck with key 1.5-10mm 3/8+20UNF | |||
| 117066058 | chuck with key 13mm 1/2" | |||
| 117066032 | 13mm DRILL CHUCK/Keyles Chuck with Lock System | |||
| 117066031 117066029 | Chuck keyles 13mm 1/2" plastic | |||
| 117066030 | Chuck keyles 13mm 3/8" plastic | |||
| 117066033 | Iron chuck keyes with lock system10omm 1/2" | |||
| 17.Ball Bearings | Code | Material Quality]PCS/CTN | ||
| 0Q0 | Model A-ClassQuality品质 | 606 | ||
| 109052 | 109156 | 绿盖/黑盖 6072RS 绿盖/黑盖 | ||
| 109006 109007 | 109116 109117 | 608 2RS 绿盖/黑盖 | ||
| 6200 | ||||
| 109016 | 109129 | 绿盖/黑盖 | ||
| 109001 | 109111 | 62012RS 绿盖/黑盖 | ||
| 605RS 绿盖/黑盖 | ||||
| 109005 | 109115 | 62001 2RS 绿盖/黑盖 | ||
| 109009 | 109119 | 626 绿盖/黑盖 | ||
| 109125 | 627 绿盖/黑盖 | |||
| 109012 | 628 绿盖/黑盖 | |||
| 109051 | 109155 | |||
| 109008 | 109118 | 629 2RS 绿盖/黑盖 | ||
| 109013 | 109126 6000 | 绿盖/黑盖 | ||
| 109014 109015 | 109127 109128 6002 | 60012RS 绿盖/黑盖 绿盖/黑盖 | ||
| B-Class Quality品质 | ||||
| 109156 | 606 | 蓝盖 | ||
| 109052 | 109116 | 607 2RS | 蓝盖 | |
| 109006 109007 | 109117 | 608 2RS | 蓝盖 | |
| 109028 | 109141 | 609 | 蓝盖 | |
| 109150 | 625 | |||
| 109038 109009 | 109119 | 626 | 蓝盖 | |
| 109012 | 109125 | 627 | 蓝盖 | |
| 109051 | 109155 | 628 | 蓝盖 | |
| 109008 | 109118 | 629 2RS | 蓝盖 | |
| 109016 | 109129 | 6200 | 蓝盖 | |
| 109001 109004 | 109111 109114 | 6201 2RS 6202 蓝盖 | 蓝盖 | |
| 109006 109007 | 109187 109158 | 6072RS | |||
| 109191 | 6082RS 626/铁盖 | ||||
| 109009 | |||||
| 109012 | 无 | 627/铁盖 | |||
| 109051 | 无 | 628 | |||
| 109008 | 109192 | 6292RS | |||
| 109037 | 无 | 698/铁盖 | |||
| 109013 | 109184 | 6000 6002 | |||
| 109015 | 无 | ||||
| 109001 | 109188 109189 | 6201 2RS | |||
| 109004 109002 | 109190 | 6202 6203 2RS | |||
| 109185 | 6001 2RS | ||||
| Wet CoreDrilBit for ConcreteandHardMasonry | |||||
| Size Package | |||||
| 一 | Z-16 Φ16X450(M32) | White box single pack | |||
| 2 | Z-18 (p18X450(M32) | White box single pack | |||
| 3 | Z-20 (p20X450(M32) | ||||
| White box single pack | |||||
| 4 | Z-22 p22X450(M32) | White box single pack | |||
| 5 | Z-25 Φ25X450(M32) | White box single pack | |||
| 6 | Z-27 p27X450(M32) | White box single pack | |||
| 7 | Z-30 (p30X450(M32) | White box single pack | |||
| 8 | Z-32p32X450(M32) | White box single pack | |||
| 9 | Z-36 p36X450(M32) | White box single pack | |||
| 10 11 | Z-38 (p38X450(M32) | White box single pack | |||
| Z-40 p40X450(M32) | White box single pack | ||||
| Z-44 p44X450(M32) | White box single pack | ||||
| Z-46 Φ46X450(M32) | White box single pack | ||||
| Z-51 p51X450(M32) | White box single pack | ||||
| Z-56 p56X450(M32) | White box single pack | ||||
| 15 16 | Z-63p63X450(M32) Z-66 p66X450(M32) | White box single pack | |||
| 17 | Z-71 p71X450(M32) | White box single pack | |||
| 18 | Z-76 p76X450(M32) | White box single pack | |||
| 19 | Z-83 p83X450(M32) | White box single pack | |||
| 20 | Z-89 89X450(M32) | White box single pack | |||
| 21 | Z-96p96X450(M32) | White box single pack | |||
| 22 | Z-102 | White box single pack | |||
| 23 | p102X450(M32) | White box single pack | |||
| 24 | Z-108 Φp108X450(M32) | White box single pack | |||
| 25 | Z-112 Φ112X450(M32) | White box single pack | |||
| 26 | Z-116p116X450(M32) Z-120 p120X450(M32) | White box single pack | |||
| 27 | Z-127 p127X450(M32) | White box single pack | |||
| 28 | Z-132 Φ132X450(M32) | White box single pack | |||
| 29 | Z-140 (p140X450(M32) | White box single pack | |||
| 30 | Z-152 p152X450(M32) | White box single pack | |||
| 31 32 | Z-160 p 160X450(M32) | White box single pack | |||
| 33 | Z-162 p162X450(M32) | White box single pack | |||
| White box single pack | |||||
| Z-168 Φ168X450(M32) | White box single pack | ||||
| 34 35 | Z-180 180X450(M32) | White box single pack | |||
| 36 | Z-200 200X450(M32) | White box single pack | |||
| 37 | Z-220 p220X450(M32) | White box single pack | |||
| 38 | Z-230 Φ230X450(M32) | White box single pack | |||
| 39 | Z-245 245X450(M32) | White box single pack | |||
| 40 | Z-254 Φ254X450(M32) | White box single pack | |||
| 41 | Z-270 p270X450(M32) | hite box single pack | |
| 42 | Z-300 p300X450(M32) | white box single pack | |
| 43 | Z-350 p350X450(M32) | White box single pack | |
| HAMMER DRILLPARTS锤镐配 | 115001091 | ||
| Gear Box Wih Neele | |||
| 115001107 | Motor Housing (Body) | ||
| 115001111+115001097Striker Wih o-ring | |||
| 115004141 | Sds adapter | ||
| 115001117 115001105/115001113Bnush Hoder | Mouth Cap Set | ||
| 115001025 | O-Ring (HEAVY) | ||
| 115001098 | O-Ring | ||
| 115001093 | Bearing Rubber | ||
| 115001074 | Oil Seal | ||
| 115001118 | Knob | ||
| 115001120 | Gear Shaf Pin | ||
| 115001099 | Piston Washer | ||
| 109159 115001116/1150012 PISTON | Needle Bearing BIG) 109055 | ||
| 115001081 | Piston Pin | ||
| 115001077 | Gear BIG) 115001049 | ||
| 109139 115001076 | Needle Bearing (Small)HK0608 | ||
| 115001114 | Thnust Bering/Neede Bearing AXK0614 | ||
| 115001106 | Tol Holder Set | ||
| Dumping BUSH Set | |||
| 115001037 | Front Half compelet set | ||
| 115001084 1150041 43 | Side Handle set | ||
| 1150041 78 | Gear Box With Needle/FRONTHOUSING 2-26 body + cover without word hole | ||
| rowspan="17"> | 1150041 42 115004135 | ||
| 2-26 body+coverwithwordhle | |||
| O-Ring (HEAVY) | 115004192 | ||
| Oil Seal | 115004137 | ||
| CarbonBrushHolder Set compelee)withall parts | 115004121 115004124 | ||
| Carbon Brsh HolderSet only | |||
| Mouth Cap Set 9pces | 115004176 | ||
| Dumping Bush Set 7pcs | 115004119 115004176 | ||
| Pendulum bearing fll se/Swing bearing+HK0907 | |||
| ToolHolderSet cmpelete | 110414 | ||
| 115004170 | |||
| Flat Gear (BIG)/11500406744T | 109159 | ||
| Needle Bearing (BIG)HK3012 | 109147 | ||
| Needle Bearing HK0709 For Gear Box/ | 115004216 | ||
| Clamper | 115004184 115004160 | ||
| Clamper with bearing(699) Set | 115004162 | ||
| Teeth Shaft Spring Inside/115004055 | |||
| Piston Pin | 115004181 | ||
| Pisont Pin with Washer | 115001093 | ||
| Bearing Coat/ | 115004166 109140 | ||
| PVC Needle Bearing K15轴承 | 115004205 | ||
| HK0910 Needle bearing | |||
| Type Clip/SWITCH CONTACT(2PCS) | 115004122 | ||
| StatorPin/tatotcoetors | 1150041 20 | ||
| U Plate | 115004125 115001082 | ||
| Knob+oring | 1150041 95 | ||
| SDS Adapter | 115004141 | ||
| Fast Connection Chuck/SDS QUICK CHUCK long Fast Connetion Chuck/SDS QUICK CHUCK short | 115004130 | ||
| 115004140 | |||
| Side Hanle set compelete | 115004149 | ||
| Ccable Slevce | 1150041 54 | ||
| Tool Holder SteelPin 钻套钢键 SmalTolHolder with 4Steel Pin | 115004186 | ||
| Front Half compelet set | 115004115 | ||
| HELICAL GEAR 33T | 115002037 | ||
| NOSECAP SET防尘帽总成 | |||
| O-RING活塞皮圈F | |||
| 115002026 RACHETSET转套总成 | 115002042 | ||
| DUMPING SET冲击组件（9pcs） | 115002038 | ||
| OUTSIDEADJUSTKNOB外调档总成 | 115002035 | ||
| ADJUST WASHER圆基片 | 115002034 | ||
| SHAFT GEAR 中间轴 HELICAL GEAR斜齿 | 115002028 | ||
| CLUTCH ASSY SET离合组件 | |||
| 115002024 | |||
| HEADCOVER头壳 | 11 5002031 BRUSHHOLDER架 | ||
| BODY机壳 | |||
| 115002036 | SWING BEARING招摆 |
| STRIKER撞锤 | |
| 115002041 | |
| NOSECAPSET防尘帽总成 | |
| 115030001 | HEADCOVER头壳带铁套，小滚针 |
| BODY机壳(包胶) | |
| 115030009 | O-RING活塞皮圈F |
| 115030011 | CYLINDER SET钻套总成 |
| DUMPING SET冲击组件 | |
| SHAFT GEAR中间轴 | |
| 115030003 | HELICALGEAR斜齿 |
| 115004125 | KNOB调档总成（带皮圈） |
| Flange铝支架总成 | |
| STATORINJECTOR定子接片2pcs | |
| 115004137 | BRUSH HOLDERSPRING刷架弹片2pcs |
| 115030006 | BRUSH HOLDER(11pcs)刷架整套 |
| 115030007 | STRIKER+ORING撞锤+皮圈 SWINGBEARING单圈摇摆 |
| 115007080 | Side Handle set |
| 115007171 oi Seal | |
| 115007054 | |
| 115007202 Switeh Handle | Oil Cap With Rubber Ring |
| 115007068 | |
| 115007176 Striker Pin | Crank Shaf with WoodRuff Key |
| 115007048 Flat Washer | |
| 115007199+112200 | |
| 105109 | Body + Brush Holder Complete Gear Box |
| 115007199 BODY | |
| 115007190 10803031 | Piston IRON |
| 10803034 | o-Ring (nomal) |
| 1052151 | O-Ring heavy |
| 1052082 IG Plate | Gear Box +IG Plate |
| 115007163 | |
| 112199 | Bottom Cover |
| Brush HolderFfll oper | |
| 115007164 | |
| 115007185 | Brush Holder Cap M14 |
| 115007089 | Piston Pin |
| 115007051 | Piston+Piston Pin |
| 115007190 | eitontPito Pit RuberRing |
| 115007176 Striker | Steel Pston |
| 115007004 | |
| 115007174 | Alu Connet Rod+Needle Bearing |
| 115007087 | Connnecting Rod Needle Bearing NK1212 |
| 115007142 rol Holder | Stee Cone RDod |
| 115007082 CYLINDER COMPELET | |
| 同第一个115007080Side Handle | |
| 115009202 Fan /Magnetic FAN | |
| 115009120 Front Kit Set 6pes/set | |
| 115009187 Front Ki Set 4pecs/Set | |
| 115009191 | |
| 115009160 | BrassBrsh Holder |
| 115009157 Thread Ring/ | Bushing/115009048 |
| 115009180 | |
| 115009158 Bearing Cover | Stopping device 2pes |
| 115009165 | Body/Motor Housing |
| 115009193 | Cylinder Sleve |
| 115009189 | Switch Handle |
| 115009130 | Side Handle set |
| 115009135 | Switch Plate with bearing |
| 115009129 115009192 | Brush Holder set |
| 115009168 | Piston /Aliumiun |
| Piston Pin | |
| 115009145 | Supporting Disc/Catch Disc |
| 10803032 | O-Ring (normal) |
| 10803033 115009182 | O-Ring (HEAVY) |
| Rubber Damping Ring | |
| 109138 | Needle Bearing K162216 |
| 115009136 | Complete GearBox |
| 115009183 | oilCap |
| 115009194 | Plastice Pston |
| 115009195 | Plastic Con.Rod |
| 115009174 | Spacer Tube+ Control Disc |
| 115009205 Tool Holder 115009206 Striker Pin |
| 115009144 115009154 Brush Holder Spring 2pes | Champer For Side Handl/CLAMP HOLDER | |
| PH 65 A SPARES | 115009164 | Oil Felt |
| 115008166 | Piston | |
| 115008156 | Piston Pin | |
| 10803030 | Piston Ring/O-Ring Fheavyqualty | |
| 115008158 | Needle Bearing For Connecting Rod/NK1820 | |
| 115008172 | Connecting Rod | |
| 115008020 | Conneting RodNeele BearingNK1820 | |
| 115008137 | Cylinder/空气缸 | |
| 104714 | Small Gear | |
| 104496 | BigGear | |
| 115008142 | Crank Shaft | |
| 115008108 | TOOLHOLDER/Front Cover | |
| 115008117 oilCover | Distance Washer/15008083 | |
| Oil Gauge | ||
| 115008161 115008136 | ||
| 115008104 | Stel Brush Holder Cap /2pes | |
| WodruffKey | ||
| 115008164 | Brush Holder Cap 20mm(2pcs) | |
| Bottom Cover | ||
| 115008174 | Body/Motor Housing定子壳1.82Kgs | |
| 115008169 | Cylinder Slee/Neck 1.45KG | |
| 115008178 115008053 | Swich Handle al | |
| 115008167 | Midle Cover+ Tp Cover | |
| Shank Slevc Mouth | ||
| 115008168 | ||
| 115008147 | Mouth Sleeve | |
| 115008048 115008180 | Damper Se 2pcs | |
| 115008134 | Lock Set 6pcs | |
| 115008114/115008184Swich Handle | Stator Ring copper 2pcs) | |
| 115008144 | Side Handle set | |
| 112201 | BrushHolder Set Fullcopper | |
| 115010076 | Front ScrewCover | |
| 7mm Lef Diretion Bolt Impact Bolt | ||
| 115010076 | Too Holder | |
| 115010075 | ||
| 115010093 | Cylincer seeve | |
| 115010058 | Knob | |
| 115010095 | Cylincer Gear Se/15010045 2es | |
| 115010074 Piston Pin | Crank Shaft | |
| 115010081 | ||
| 115010097 | Piston with Pin | |
| 115010078 | Connecting Rod with Needle Bearing Piston Ring(heavy) | |
| 115010092 | Switch Handle | |
| 115010083 1150010070 | Front Cap Set DCA quality) | |
| 115010090 | GEAR BOX+IG plate SET | |
| 103006 | BIG HELICAL GEAR | |
| STATOR | ||
| 115010082 | PISTON WITH CONNECTING ROD WITH O RING | |
| 30603128 115010091 | BODY/Motor Housing | |
| 115010089 | CARBONBRUSHHolder (ull oper) | |
| 108237 il seal(small | SMALL HELICAL GEAR | |
| 115010073 | OIL CAP | |
| 115010068 | STRIKER | |
| 105083 | Alu Bearing Box | |
| 106126 110056 | Full Body Set | |
| Spanner | ||
| 116095 AB Washer | ||
| 105083 | Gear Box Full Set | |
| 117061017 Lock Set | ||
| 6-100 SPARE PARTS | 107726 Switch | |
| 1052184 | Rubber Bearing For Gear Box/PVC Bearing+6201 | |
| 108169 | 607 Bearing Coat | |
| PVC Bearing Dabbi (OLD) | ||
| pVC Bearing Box (NEW) | ||
| 雷同 | Alu Bearing Box | |
| 106458 | IG Plate Center Cove/Bafle Plate | |
| 10602015 106482 112253 | Knob+ Lever Brush Holder +Spring (4pcs/set) | |
| 112204/112226 10602012 | Brush Holder With Spring | |
| Wind Guard/FAN GUARD/BAFFLE | ||
| 106461 | Bearing coat.Thick one | |
| 112331/112269 | Brush Holder Support | |
| 110058 | Spanner for 6-100Washer | |
| 132037 | Spindle new one | |
| 106133 | Body Set complete | |
| 117061083 | Lock Set 3pes | |
| 105078/1052193 | Gear Box +Bearing Box +Lock Set+ needleBearing | |
| 109123 | Needle bearing for gearBox use (HK 0810) | |
| 1052167 1052083/ 1052111 | Bearing Holder | |
| Bearing Holder with Bearing (aliumiun) | ||
| 131034/116095 | AB Washer(2irons) | |
| 10601007 | side Handle | |
| 10603202 | Body | |
| 10604008 | Switch Handle | |
| 132019 | Spindle | |
| 131037 | AB Washer | |
| 1052093 | Bearing Coat | |
| 118068 | Whe Guard 150mm | |
| 105088 | ||
| G15SA2 SPARE PARTS | 112286 | Complete Gear Box Set brush cap |
| 111240 | carbon brush | |
| 110049 | spanner | |
| G18SE2 SPARE PARTS | 132024 | Spindle |
| 112294 | HolderCap | |
| G10SS SPARE PARTS | 112220 | Brush Holder+Cap |
| 112256 | Brush Holder Cap | |
| 1052139 | Bearing Box +Bearing | |
| MT410 SPARE PARTS | 112280 | |
| 10603105 | Carbon cap Motor Housing | |
| 131033 | AB Washer | |
| 117067012 | Base Plate | |
| 112292 | Bush Holder + Cap | |
| 115018001 | Spring | |
| LG355SPAREPARTS | 10604007 | Handle |
| 146009 | ||
| Wood druff key | ||
| 112206 | Brush Holder | |
| 112264 | LG355 Brush Holder Cap | |
| PD100SPAREPARTS | 1052088/1052089 | Bearing Holder |
| 131035/ 131057 | ||
| 112279/112299 | AB Washer | |
| 118045 | Brush Holder Cap | |
| 112208/112273 | Wheel Guard Brush Holder | |
| 105082 | Complete Gear Box (3pes) | |
| 116563 | Metal Cover | |
| 10601009 | ||
| 1052075 | Side Handle Gear Box | |
| 104462 | Gear | |
| SMALL GEAR/Sprocket | ||
| Sprocket New 9*12mm | ||
| Sprocket | ||
| Adjust Bold Set | ||
| 106005 | Body | |
| 132112 | 5016 spindle | |
| 117196 | 22" hain | |
| 117193 | 16" chain |
CUTTING
DIAMONDSAWBLADE
Diamond saw blade is a cutting tool, widely used in processing of hard and britte materials such as stone, concrete,precast slab, new and old roads, ceramics and so on.
General Purpose
·Excellent cutting ability
·Meeting thecomprehensiverequirementsofprofessional users
·Ensure excellent cuting performance and long
servicelife
Tile
·Sharp cutting ·Attain average cutting surface · Professional products ensurehigh efficiency
Concrete
·For cutting high-grade concrete ·Professional cutters surpass higher cutting standards ·Best choice for professional users
DIAMONDSAWBLADE
| Diameter (mm) | Tooth Thickness (mm) | Aperture (mm) | ApplicationScenarios | Ring | PCS/CTN | |
| Outer Diameter(mm) | Hole Diameter (mm) | |||||
| Φ105 (NO.0) | 1.8 | 20 | Economical Grade | 20 | 16 | 200 |
| Φ105 (NO.1) | 1.8 | 20 | Wall | 20 | 16 | 200 |
| Φ108 (NO.2) | 1.8 | 20 | Wall | 20 | 16 | 200 |
| Φ108 (NO.3) | 1.8 | 20 | Tile | 20 | 16 | 200 |
| Φ108 (NO.4) | 1.8 | 20 | Concreate | 20 | 16 | 200 |
| Φ112 (NO.5) | 2.0 | 20 | Granite,Marble | 20 | 16 | 200 |
| Φ110 (NO.6) | 1.8 | 20 | General Purpose | 20 | 16 | 200 |
| Φ180 | 2.4 | 25.4 | General Purpose | 25.4 | 22.2 | 50 |
| Φ180 | 2.4 | 22.2 | General Purpose | 22.2 | 20 | 50 |
| Φ105(NO.8) | 1.6 | 20 | Thin Turbo | 20 | 16 | 200 |
| Φ112(NO.9) | 1.8 | 20 | General Purpose | 20 | 16 | 200 |
| Φ114 | 2.2 | 20 | Dry Cutting | 20 | 16 | 200 |
| Φ114 | 2.2 | 22.2 | Dry Cutting | 22.2 | 20 | 200 |
| Φ108 | 1.8 | 20 | Dry Cutting | 20 | 16 | 200 |
Application Scenarios:
| Diameter | Toth Thik nes | Aoperture | Application Scenarios | PCS/CTN | ||
| Φ125 | 2.0 | 22.2 | General Purpose | 22.2 | 20 | 200 |
| Φ150 | 2.0 | 22.2 | Grooving | 22.2 | 20 | 100 |
| Φ188 | 2.3 | 25.4 | Sharp Type | 25.4 | 22.2 | 50 |
| Φ188 | 2.3 | 25.4 | General Purpose | 25.4 | 22.2 | 50 |
| Φ190 | 2.6 | 25.4 | Dry Cutting | 25.4 | 22.2 | 50 |
| Φ190 | 2.8 | 25.4 | General Purpose | 25.4 | 22.2 | 50 |
| Φ230 | 2.6 | 25.4 | General Purpose | 25.4 | 22.2 | 50 |
| Φ230 | 2.6 | 22.2 | General Purpose | 22.2 | 20 | 50 |
| Φ250 | 2.6 | 25.4 | General Purpose | 25.4 | 22.2 | 50 |
| Φ368 | 3.6 | 50 | Concreate Blade | / | 10 | |
| Φ418 | 3.6 | 50 | Concreate Blade | / | / | 10 |
| Φ518 | 4.0 | 50 | Concreate Blade | / | / | 5 |
CUTTING
TCT SAW BLADES
(Professional Grade/Decoration Grade)
TCT SAW BLADE (Professional Grade)
| Diameter (mm) | Tooth Thickness (mm) | Aperture (mm) | Number of Teeth | Teeth Shape | Application Scenarios | Outer Diameter (mm) | HoleDiameter (mm) | PCS/CTN |
| 105(4") | 1.8 | 20 | 30T | ATB | Wood | 20 | 16 | 200 |
| 110(4") | 1.8 | 20 | 40T | ATB | Wood | 20 | 16 | 200 |
| 125(5") | 1.8 | 20 | 40T | ATB | Wood | 20 | 16 | 100 |
| 180(7") | 1.8 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 50 |
| 180(7") | 1.8 | 20 | 40T | ATB | Wood | 20 | 16 | 50 |
| 180(7") | 1.8 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 50 |
| 180(7") | 1.8 | 20 | 60T | ATB | Wood | 20 | 16 | 50 |
| 230(9") | 2.4 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 50 |
| 230(9") | 2.4 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 50 |
| 254(10") | 2.4 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 25 |
| 254(10") | 2.4 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 25 |
| 254(10") | 2.4 | 25.4 | 80T | ATB | Wood | 25.4 | 20 | 25 |
| 254(10") | 2.4 | 25.4 | 100T | ATB | Wood | 25.4 | 20 | 25 |
| 254(10") | 2.4 | 25.4 | 120T | ATB | Wood | 25.4 | 20 | 25 |
| 300(12") | 3.2 | 30.0 | 40T | ATB | Wood | 30.0 | 25.4 | 20 |
| 300(12") | 3.2 | 30.0 | 60T | ATB | Wood | 30.0 | 25.4 | 20 |
| 300(12") | 3.2 | 30.0 | 80T | ATB | Wood | 30.0 | 25.4 | 20 |
| Diameter | Toth Thiknes | Aperture | Number | Sheth | Aspliation | Outer iameter | Holediameter | PCS/CTN |
| 300(12") | 3.2 | 30.0 | 100T | ATB | Wood | 30.0 | 25.4 | 20 |
| 300(12") | 3.2 | 30.0 | 120T | ATB | Wood | 30.0 | 25.4 | 20 |
| 350(14") | 3.2 | 30.0 | 40T | ATB | Wood | 30.0 | 25.4 | 10 |
| 350(14") | 3.2 | 30.0 | 60T | ATB | Wood | 30.0 | 25.4 | 10 |
| 350(14") | 3.2 | 30.0 | 80T | ATB | Wood | 30.0 | 25.4 | 10 |
| 350(14") | 3.2 | 30.0 | 100T | ATB | Wood | 30.0 | 25.4 | 10 |
| 350(14") | 3.2 | 30.0 | 120T | ATB | Wood | 30.0 | 25.4 | 10 |
| 105(4") | 1.8 | 20 | 40T | ATB | Aluminium & Wood | 20 | 16 | 200 |
| 230(9") | 2.4 | 25.4 | 80T | TCG | Aluminium & Wood | 25.4 | 20 | 50 |
| 250(10") | 2.8 | 25.4 | 100T | TCG | Aluminium | 25.4 | 20 | 25 |
| 250(10") | 2.8 | 25.4 | 120T | TCG | Aluminium | 25.4 | 20 | 25 |
| 300(12") | 3.2 | 30.0 | 100T | TCG | Aluminium | 30.0 | 25.4 | 20 |
| 300(12") | 3.2 | 30.0 | 120T | TCG | Aluminium | 30.0 | 25.4 | 20 |
| 350(14") | 3.2 | 30.0 | 100T | TCG | Aluminium | 30.0 | 25.4 | 10 |
| 350(14") | 3.2 | 30.0 | 120T | TCG | Aluminium | 30.0 | 25.4 | 10 |
TCT SAW BLADE (Decoration Grade)
| Diameter (mm) | Tooth Thickness (mm) | Aperture (mm) | Number of Teeth | Teeth Shape | Application Scenarios | Outer Diameter (mm) | Hole Diameter (mm) | PCS/CTN |
| 105(4") | 1.5 | 20 | 30T | ATB | Wood | 20 | 16 | 200 |
| 105(4") | 1.5 | 20 | 40T | ATB | Wood | 20 | 16 | 200 |
| 180(7") | 1.8 | 25.4 | 40T | ATB | Wood | 25.4 | 16 | 50 |
| 180(7") | 1.8 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 50 |
| 200(8") | 2.0 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 25 |
| 200(8") | 2.0 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 25 |
| 230(9") | 2.4 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 25 |
| 230(9") | 2.4 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 25 |
| 230(9") | 2.6 | 25.4 | 80T | ATB | Wood | 25.4 | 20 | 25 |
| 255(10") | 2.6 | 25.4 | 40T | ATB | Wood | 25.4 | 20 | 25 |
| 255(10") | 2.6 | 25.4 | 60T | ATB | Wood | 25.4 | 20 | 25 |
| 255(10") | 2.6 | 25.4 | 80T | ATB | Wood | 25.4 | 20 | 25 |
| 254(10") | 2.8 | 25.4 | 100T | TCG | Aluminium | 25.4 | 20 | 25 |
| 254(10") | 2.8 | 25.4 | 120T | TCG | Aluminium | 25.4 | 20 | 25 |
TCTSAWBLADE(SHARPTYPE)
Suitableforcordlesscircularsaw
| Diameter (mm) | Tooth Thickness (mm) | Aperture (mm) | Number of Teeth | Teeth Shape | Application Scenarios | PCS/CTN |
| 125(5") | 1.5 | 20 | 24T | ATB | Wood | 100 |
| 140(5-1/2") | 1.6 | 20 | 24T | ATB | Wood | 100 |
| 165(6-1/2") | 1.5 | 20 | 24T | ATB | Wood | 50 |
| 185(7") | 1.6 | 20 | 24T | ATB | Wood | 50 |
SAW CHAIN
| No. | Chain Length | PCS/CTN |
| 1 | 4" | 50 |
| 2 | 6" | 50 |
| 3 | 8 | 50 |
| 4 | 10" | 50 |
| 5 | 16" | 50 |
| 6 | 16" | 50 |
| 7 | 16" | 50 |
| 8 | 18" | 50 |
| 9 | 20" | 50 |
| 10 | 20″ | 50 |
GRINDING/POLISHING
SANDINGSHEET
| No. | Specification (mm) | Packing(pcs) |
| 1 | Φ125*P80 | 2000 |
| 2 | Φ125*P120 | 2000 |
| 3 | Φ125*P180 | 2000 |
| 4 | Φ125*P240 | 2000 |
| 5 | Φ125*P320 | 2000 |
CUTOFFWHEEL
| No. | Specification(mm) | Colour | Packing(pcs) |
| 1 | 100x2.5x16 (double net) | Black/Green/Brown | 600 |
| 2 | 105x1.2x16 | Black | 800 |
| 3 | 105x1.2x16 | Green | 800 |
| 4 | 107x1.0x16 (Plastic Bucket)(double net) | Black/Green/Brown | 800 |
| ５ | 107x1.0x16 (lron Box)(double net) | Black/Green/Brown | 800 |
| 6 | 107x1.2x16 (single net) | Black/Green/Brown | 800 |
| 7 | 115x1.0x22.23 (double net) | Black/Green/Brown | 400 |
| 8 | 115x1.2x22.23 (double net) | Black/Green/Brown | 400 |
| 9 | 115x1.6x22.23 (double net) | Black/Green/Brown | 400 |
| 10 | 125x1.0x22 (double net) | Black/Green/Brown | 400 |
| 11 | 125x1.2x22 (double net) | Black/Green/Brown | 400 |
| 12 | 125x3.0x22 (double net) | Black/Green/Brown | 300 |
| 13 | 150x1.5x22 (double net) | Black/Green/Brown | 300 |
| 14 | 150x3.0x22 (double net) | Black/Green/Brown | 200 |
| 15 | 180x1.6x22 (double net) | Black/Green/Brown | 200 |
| 16 | 180x3.0x22 (double net) | Black/Green/Brown | 200 |
| 17 | 230x2.0x22 (double net) | Black/Green/Brown | 100 |
| 18 | 230x3.0x22 (double net) | Black/Green/Brown | 100 |
| 19 | 250x2.0x25.4 (double net) | Black/Green/Brown | 100 |
| 20 | 250x3.0x25.4 (double net) | Black/Green/Brown | 50 |
| 21 | 305x2.5x25.4 (double net) | Black/Green/Brown | 50 |
| 22 | 305x3.0x25.4 (double net) | Black/Green/Brown | 25 |
| 23 | 355x2.5x25.4 (single net) | Black/Green/Brown | 30 |
| 24 | 355x3.0x25.4 (double net) | Black/Green/Brown | 25 |
| 25 | 355x3.2x25.4 (single net) | Black/Green/Brown | 25 |
| 26 | 355x3.2x25.4 (double net) | Black/Green/Brown | 25 |
| 27 | 400x3.0x32 (single net) | Black/Green/Brown | 25 |
| 28 | 400x3.0x32 (double net) | Black/Green/Brown | 25 |
| 29 | 400x3.2x32 (single net /double net) | Black(High power) | 25 |
| 30 | 400x4.0x32 (single net /double net) | Black(High power) | 25 |
GRINDINGWHEEL
| No. | Specification(mm) | Colour | Packing(pcs) |
| 1 | 100x3.0x16 (double net) | Black/Green/Brown | 400 |
| 2 | 100x4.0x16 (double net) | Black/Green/Brown | 300 |
| 3 | 100x5.0x16 (double net) | Black/Green/Brown | 200 |
| 4 | 100x6.0x16 (double net) | Black/Green/Brown | 200 |
| 5 | 115x3.0x22.23 (double net) | Black/Green/Brown | 400 |
| 6 | 115x6.0x22.23 (double net) | Black/Green/Brown | 200 |
| 7 | 125x6.0x22 (double net) | Black/Green/Brown | 150 |
| 8 | 150x6.0x22 (2.5 net) | Black/Green/Brown | 100 |
| 9 | 180x6.0x22 (2.5 net) | Black/Green/Brown | 50 |
| 10 | 230x6.0x22 (2.5 net) | Black/Green/Brown | 50 |
FLAP DISCS
| No. | Specification(mm) | Material | Grit | PCS/CTN |
| 1 | 100 x 16 × 72 | Plastic Back Aluminium Oxide Flap Disc60# | 60 | 400 |
| 2 | 100 x 16 x 72 | PlasticBack Aluminium Oxide FlapDisc 80# | 80 | 400 |
| 3 | 100 x16 × 72 | Plastic Backing Calcined Flap Disc 80# | 80 | 400 |
| 4 | 100 x 16 x 72 | Fiber Backing Calcined Flap Disc 60# | 60 | 400 |
| ５ | 100 x 16 x 72 | Fiber Backing Calcined Flap Disc 80# | 80 | 400 |
DIAMONDGRINDINGDISCS
| No. | Name | Specification(mm) | Ring | PCS/CTN | |
| Outer Diameter(mm) | Hole Diameter(mm) | ||||
| 1 | Diamond Grinding Disc | 80 x 16 | / | / | 100 |
| 2 | Diamond Grinding Disc | 100 x 16 | / | / | 100 |
| 3 | Diamond Grinding Disc | 100 x 22.2 | 22.2 | 16 | 100 |
DRILLING(Masonry)
Tungsten Carbide-tipped Bits
Longfervicelifeforconcreteandreinforcedconcrete.
HAMMERDRILLBITS
| No. | Specification (mm) | Shank Type | No. | Specification (mm) | Shank Type |
| 1 | Φ6x110 | SDS-Plus | 31 | Φ10x280 | Hex |
| 2 | Φ6x160 | SDS-Plus | 32 | Φ12x280 | Hex |
| 3 | Φ8x110 | SDS-Plus | 33 | Φ14x280 | Hex |
| 4 | Φ8x160 | SDS-Plus | 34 | Φ16x280 | Hex |
| 5 | Φ10x160 | SDS-Plus | 35 | Φ18x280 | Hex |
| 6 | Φ12x160 | SDS-Plus | 36 | Φ20x280 | Hex |
| 7 | Φ14x160 | SDS-Plus | 37 | Φ22x280 | Hex |
| 8 | Φ16x160 | SDS-Plus | 38 | Φ25x280 | Hex |
| 9 | Φ8x210 | SDS-Plus | 39 | Φ28x280 | Hex |
| 10 | Φ10x210 | SDS-Plus | 40 | Φ14x400 | Hex |
| 11 | Φ12x210 | SDS-Plus | 41 | Φ16x400 | Hex |
| 12 | Φ14x210 | SDS-Plus | 42 | Φ18x400 | Hex |
| 13 | Φ16x210 | SDS-Plus | 43 | Φ20x400 | Hex |
| 14 | Φ18x210 | SDS-Plus | 44 | Φ22x400 | Hex |
| 15 | Φ20x210 | SDS-Plus | 45 | Φ25x400 | Hex |
| 16 | Φ22x210 | SDS-Plus | 46 | Φ28x400 | Hex |
| 17 | Φ25x210 | SDS-Plus | 47 | Φ30x400 | Hex |
| 18 | Φ10x350 | SDS-Plus | 48 | Φ32x400 | Hex |
| 19 | Φ12x350 | SDS-Plus | 49 | Φ35x400 | Hex |
| 20 | Φ14x350 | SDS-Plus | 50 | Φ14x505 | Hex |
| 21 | Φ16x350 | SDS-Plus | 51 | Φ16x505 | Hex |
| 22 | Φ18x350 | SDS-Plus | 52 | Φ18x505 | Hex |
| 23 | Φ20x350 | SDS-Plus | 53 | Φ20x505 | Hex |
| 24 | Φ22x350 | SDS-Plus | 54 | Φ22x505 | Hex |
| 25 | Φ25x350 | SDS-Plus | 55 | Φ25x505 | Hex |
| 26 | Φ10x200 | Hex | 56 | Φ28x505 | Hex |
| 27 | Φ14x200 | Hex | 57 | Φ30x505 | Hex |
| 28 | Φ16x200 | Hex | 58 | Φ32x505 | Hex |
| 29 | Φ18x200 | Hex | 59 | Φ35x505 | Hex |
| 30 | Φ20x200 | Hex | 60 | Φ38x505 | Hex |
| No. | Specification (mm) | Shank Type | No. | Specification (mm) | Shank Type | ||
| 63 | Φ30x700 | Hex | 83 | Φ25x400 | SDS-Max | ||
| 64 | Φ32x700 | Hex | 84 | Φ28x400 | SDS-Max | ||
| 65 | Φ35x700 | Hex | 85 | Φ30x400 | SDS-Max | ||
| 66 | Φ38x700 | Hex | 86 | Φ14x500 | SDS-Max | ||
| 67 | Φ10x280 | SDS-Max | 87 | Φ16x500 | SDS-Max | ||
| 68 | Φ12x280 | SDS-Max | 88 | Φ18x500 | SDS-Max | ||
| 69 | Φ14x280 | SDS-Max | 89 | Φ20x500 | SDS-Max | ||
| 70 | Φ16x280 | SDS-Max | 90 | Φ22x500 | SDS-Max | ||
| 71 | Φ18x280 | SDS-Max | 91 | Φ25x500 | SDS-Max | ||
| 72 | Φ20x280 | SDS-Max | 92 | Φ28x500 | SDS-Max | ||
| 73 | Φ22x280 | SDS-Max | 93 | Φ30x500 | SDS-Max | ||
| 74 | Φ25x280 | SDS-Max | 94 | Φ32x500 | SDS-Max | ||
| 75 | Φ28x280 | SDS-Max | 95 | Φ6x110 | SDS-Pus(Double-Groove) | ||
| 76 | Φ30x280 | SDS-Max | 96 | Φ6x160 | SDS-Pus(Double-Groove) | ||
| 77 | Φ12x400 | SDS-Max | 97 | Φ8x110 | SDS-Pus(Double-Groove) | ||
| 78 | Φ14x400 | SDS-Max | 98 | Φ8x160 | SDS-Pus(Double-Groove) | ||
| 79 | Φ16x400 | SDS-Max | 99 | Φ10x110 | SDS-Pus(Double-Groove) | ||
| 80 | Φ18x400 | SDS-Max | 100 | Φ10x160 | SDS-Pus(Double-Groove) | ||
| 81 | Φ20x400 Φ22x400 | SDS-Max SDS-Max | 101 | Φ12x160 | SDS-Pus(Double-Groove) | ||
| 82 | |||||||
| CHISELS ■ Chisel Flat | Chisel Point | ||||||
| No. | Name | Specification (mm) | Shank Type | No. | Name Point Chisel | Specification (mm) Φ14x250 | Shank Type |
| 1 | Flat Chisel | Φ14x250 | SDS-Plus | 1 | Point Chisel | Φ17x280 | SDS-Plus |
| 2 | Flat Chisel | Φ17x280 | Hex | 2 | Hex | ||
| 3 | Flat Chisel | Φ17x350 | Hex | 3 | Point Chisel | Φ17x350 | Hex |
| 4 | Flat Chisel | Φ17x400 | Hex | 4 | Point Chisel | Φ17x400 | Hex |
| 5 | Flat Chisel | Φ18x280 | SDS-Max | 5 | Point Chisel | Φ18x280 | SDS-Max |
| ６ | Flat Chisel | Φ18x350 | SDS-Max | ６ | Point Chisel | Φ18x350 | SDS-Max |
| 7 | Flat Chisel | Φ18x400 | SDS-Max | 7 | Point Chisel | Φ18x600 | SDS-Max |
| 8 | Flat Chisel | Φ18x400 | SDS-Max | 8 9 | Point Chisel | Φ21x350 | Hex |
WALL HOLE SAW
| No. | Name | Specification(mm) |
| 1 | Wall Hole Saw | 30 |
| 2 | Wall Hole Saw | 35 |
| 3 | Wall Hole Saw | 40 |
| 4 | Wall HoleSaw | 45 |
| 5 | Wall HoleSaw | 50 |
| ６ | Wall Hole Saw | 55 |
| 7 | Wall HoleSaw | 60 |
| 8 | Wall Hole Saw | 65 |
| 9 | Wall Hole Saw | 70 |
| 10 | SDS Plus Shank Wall Hole Saw | 350 |
DIAMONDCOREBITS
| Specification (mm) | Specification (mm) | ||||
| Diameter | Total Length | Working Length | Diameter | Total Length | Working Length |
| Φ18 | 370 | 300 | Φ108 | 350 | 290 |
| Φ20 | 370 | 300 | Φ112 | 350 | 290 |
| Φ25 | 370 | 300 | Φ120 | 350 | 290 |
| Φ27 | 370 | 300 | Φ127 | 350 | 290 |
| Φ32 | 370 | 310 | Φ132 | 350 | 290 |
| Φ36 | 370 | 310 | Φ152 | 350 | 290 |
| Φ38 | 370 | 310 | Φ159 | 350 | 290 |
| Φ40 | 370 | 310 | Φ162 | 350 | 290 |
| Φ44 | 370 | 310 | Φ168 | 350 | 290 |
| Φ46 | 370 | 310 | Φ180 | 350 | 290 |
| Φ51 | 370 | 310 | Φ200 | 350 | 290 |
| Φ56 | 370 | 310 | Φ220 | 350 | 290 |
| Φ63 | 370 | 310 | Φ230 | 350 | 290 |
| Φ66 | 370 | 310 | Φ245 | 350 | 290 |
| Φ71 | 370 | 310 | Φ254 | 350 | 290 |
| Φ76 | 370 | 310 | Φ25 | 450 | 380 |
| Φ83 | 370 | 310 | Φ27 | 450 | 380 |
| Φ89 | 370 | 310 | Φ32 | 450 | 390 |
| Φ96 | 350 | 290 | Φ36 | 450 | 390 |
| Φ102 | 350 | 290 | Φ38 | 450 | 390 |
DIAMOND CORE BITS (1-1/4 thread)
| Specification (mm) | Specification (mm) | ||||
| Diameter | Total Length | Working Length | Diameter | Total Length | Working Length |
| Φ40 | 450 | 390 | Φ102 | 450 | 390 |
| Φ44 | 450 | 390 | Φ112 | 450 | 390 |
| Φ51 | 450 | 390 | Φ152 | 450 | 390 |
| Φ56 | 450 | 390 | Φ127 | 450 | 390 |
| Φ63 | 450 | 390 | Φ162 | 450 | 390 |
| Φ76 | 450 | 390 | Φ168 | 450 | 390 |
| Φ83 | 450 | 390 | Φ180 | 450 | 390 |
| Φ89 | 450 | 390 | Φ200 | 450 | 390 |
| Specification (mm) | Specification (mm) | ||||
| Diameter | Total Length | Working Length | Diameter | Total Length | Working Length |
| Φ25 | 365 | 300 | Φ102 | 455 | 390 |
| Φ27 | 365 | 300 | Φ108 | 455 | 390 |
| Φ51 | 365 | 310 | Φ112 | 455 | 390 |
| Φ56 | 365 | 310 | Φ120 | 455 | 390 |
| Φ63 | 365 | 310 | Φ127 | 455 | 390 |
| Φ76 | 365 | 310 | Φ132 | 455 | 390 |
| Φ83 | 365 | 310 | Φ152 | 455 | 390 |
| Φ102 | 365 | 300 | Φ160 | 455 | 390 |
| Φ112 | 365 | 300 | Φ162 | 455 | 390 |
| Φ120 | 365 | 300 | Φ168 | 455 | 390 |
| Φ127 | 365 | 300 | Φ200 | 455 | 390 |
| Φ152 | 365 | 300 | Φ254 | 455 | 390 |
| Φ162 | 365 | 300 | |||
| Φ168 | 365 | 300 | |||
| Φ200 | 365 | 300 | |||
| Φ25 | 455 | 380 | |||
| Φ27 | 455 | 380 | |||
| Φ32 | 455 | 390 | |||
| Φ51 | 455 | 390 | |||
| Φ56 | 455 | 390 | |||
| Φ63 | 455 | 390 | |||
| Φ76 | 455 | 390 | |||
| Φ83 | 455 | 390 | |||
DIAMONDCOREBITEXTENSION
| No. | Specification | PCS/CTN |
| 1 | p30x160 | 55 |
| 2 | (p30x200 | 40 |
| 3 | p30x230 | 36 |
| 4 | p30x300 | 28 |
DIAMONDHOLESAW
| No. | Specification(mm) | Packing(pcs) | PCS/CTN |
| 1 | Φ6 | 5 | 6000 |
| 2 | 8 | ５ | 3000 |
| 3 | Φ10 | ５ | 3000 |
| 4 | Φ12 | ５ | 1800 |
| 5 | Φ14 | 5 | 1800 |
| 6 | Φ16 | 5 | 1200 |
| 7 | Φ18 | 5 | 1000 |
| 8 | Φ20 | ５ | 1000 |
| 9 | Φ22 | 5 | 1000 |
| 10 | Φ26 | ５ | 500 |
| 11 | Φ30 | 5 | 500 |
| 12 | Φ32 | 2 | 400 |
| 13 | Φ35 | 2 | 400 |
| 14 | Φ38 | 2 | 300 |
| 15 | Φ40 | 2 | 300 |
| 16 | Φ42 | 2 | 300 |
| 17 | Φ45 | 2 | 300 |
| 18 | Φ50 | 2 | 200 |
Application Scenarios:
DRILLING(Wood/Metal)
TWISTDRILLBITS
| Specification | Material | Packing (pcs) | PCS/CTN | Specification (mm) | Material | Packing (pcs) | PCS/CTN |
| 1.0 | 6542 | 10 | 4000 | 8.8 | 6542 | 10 | 600 |
| 1.5 | 6542 | 10 | 4000 | 9.0 | 6542 | 10 | 600 |
| 2.0 | 6542 | 10 | 4000 | 9.5 | 6542 | 10 | 600 |
| 2.2 | 6542 | 10 | 4000 | 9.8 | 6542 | 5 | 300 |
| 2.5 | 6542 | 10 | 4000 | 10.0 | 6542 | 5 | 300 |
| 2.8 | 6542 | 10 | 4000 | 10.5 | 6542 | 5 | 300 |
| 3.0 | 6542 | 10 | 4000 | 11.0 | 6542 | 5 | 300 |
| 3.2 | 6542 | 10 | 4000 | 11.5 | 6542 | 5 | 300 |
| 3.3 | 6542 | 10 | 4000 | 12.0 | 6542 | 5 | 300 |
| 3.5 | 6542 | 10 | 4000 | 12.5 | 6542 | 5 | 300 |
| 3.6 | 6542 | 10 | 4000 | 13.0 | 6542 | ５ | 300 |
| 3.8 | 6542 | 10 | 4000 | ||||
| 4.0 | 6542 | 10 | 4000 | 135° | |||
| 4.2 | 6542 | 10 | 1600 | ||||
| 4.4 | 6542 | 10 | 1600 | ||||
| 4.5 | 6542 | 10 | 1600 | ||||
| 4.8 | 6542 | 10 | 1200 | ||||
| 5.0 | 6542 | 10 | 1200 | ||||
| 5.2 | 6542 | 10 | 1200 | ||||
| 5.3 | 6542 | 10 | 1200 | ||||
| 5.5 | 6542 | 10 | 1200 | ||||
| 5.8 | 6542 | 10 | 1200 | ||||
| 6.0 | 6542 | 10 | 1200 | ||||
| 2.65 | 6542 | 11 | 1200 | 川I | |||
| 6.7 6.8 | 6542 | 10 | 1200 | ||||
| 7.0 | 6542 6542 | 10 | 1200 | ||||
| 7.2 | 6542 | 10 10 | 1200 | ||||
| 7.5 | 6542 | 10 | 1200 1200 | ||||
| 8.0 | 6542 | 10 | 600 | ||||
| 8.5 | 6542 | 10 | 600 |
HSSHOLESAWS
| Specification (mm) | Packing (pcs) | PCS/CTN |
| Φ35 | 10 | 120 |
T.C.TANNULARCUTTINGBIT
| Shank Type | Specification | |
| Cuting Diameter(mm) | Cuting Depth(mm) | |
| Weldon Shank | Φ22 | 35 |
WOODDRILLBIT
| No. | Specification (mm) | Packing | |
| pcs/box | pcs/ctn | ||
| 1 | p3x60 | 10 | 4000 |
| 2 | (p4x75 | 10 | 4000 |
| 3 | p5x85 | 10 | 3000 |
| 4 | Φ6x95 | 10 | 3000 |
| 5 | p7x110 | 10 | 1000 |
| 6 | p8x115 | 10 | 1000 |
| 7 | p9x125 | 5 | 500 |
| 8 | (p10x133 | 5 | 500 |
| 9 | (p12x151 | 5 | 200 |
| 10 | (p14x160 | 1 | 100 |
| 11 | p16x160 | 1 | 100 |
| 12 | (p18x180 | 1 | 100 |
| 13 | p20x200 | 1 | 100 |
THREE-POINTEDCUTTINGEDGE
Fast and accurate positioning, smoothdrilling without deviation
SPIRALCHIPDISCHARGEGROOVE
High speed and fast chip discharge, high efficiency
HIGHCARBONSTEELMATERIAL
Overall quenching,wear-resistantand durable
FASTENING
SCREWDRIVERBIT
| Picture | Model | Head | Type | Specification | Packing | ||
| pcs/box | pcs/ctn | ||||||
| 田田 | Double | A | PH2x65 | 10 | 1000 | A B | |
| 田田 | Double | A | PH2x100 | 10 | 1000 | ||
| 田田 | Double | A | PH2x150 | 10 | 400 | ||
| 田田 | Double | B | PH2x65 | 10 | 1000 | ||
| Double | B | PH2/6mmx65 | 10 | 1000 | |||
MAGNETICNUTSETTER
| Picture | Model | Head | Type | Specification | Packing | ·Alloy steel manufactured,overal quenching | |
| pcs/box | pcs/ctn | ||||||
| 田田 | Double High Torque/A | PH2x65 | 10 | 1000 | · High occlusal degree | ||
| 田 | Single | / | PH1x25 | 20 | · Head with magnetic | ||
| 田 | Single | / | PH2x25 | 20 | 2000 | ||
| No. | Specification (mm) | Packing | |
| pcs/box | pcs/ctn | ||
| 1 | 6x65 | 50 | 500 |
| 2 | 7x65 | 50 | 500 |
| 3 | 8x65 | 50 | 500 |
| 4 | 9x65 | 40 | 400 |
| 5 | 10x65 | 40 | 400 |
| ６ | 11x65 | 35 | 350 |
| 7 | 12x65 | 35 | 350 |
| 8 | 13x65 | 35 | 350 |
| 9 | 14x65 | 30 | 300 |
PNEUMATIC TOOL
EVASPRINGTUBES(WITHQUICKCONNECTOR)
| No. | Material | Specification (mm) | Length(m) | Colour | PCS/CTN |
| 1 | EVA | Φ8x5 | 9 | Transparent | 70 |
| 2 | EVA | Φ8x5 | 9 | Blue | 70 |
| 3 | EVA | Φ8x5 | 9 | Red | 70 |
| 4 | EVA | Φ8x5 | 12 | Transparent | 50 |
| 5 | EVA | Φ8x5 | 12 | Blue | 50 |
| 6 | EVA | Φ8x5 | 12 | Red | 50 |
AIRBLOWGUN
| No. | Specification(mm) | pcs/ctn |
| 1 | 100 | 100 |
PNEUMATICQUICKCONNECTORS
| No. | Name | Specification | PCS/CTN |
| 1 | Pneumatic Quick Connector(5x8) | PP20+SP20 | 200 |
| 2 | Pneumatic Quick Connector (Interal Thread) | PM20+SM20 | 200 |
| 3 | Pneumatic Quick Connector(Extemal Thread) | PF20+SF20 | 200 |
| 4 | Pneumatic Quick Connector (Long Tail) | PH20+SH20 | 200 |
| ５ | Pneumatic Quick Connector (Round Two-way) | SMV | 120 |
| 6 | Pneumatic Quick Connector (Round Three-way) | SMY | 100 |
MISCELLANEOUS
DRILL CHUCKS
| Drill Chuck | Specification (mm) | ApplicationRange(mm) | PCS/CTN | |
| 上 | 6mm 3/8-24UNF(Threaded) | 0.6-6.0 | 100 | |
| 6mm B10(Taper Shank) | 0.6-6.0 | 100 | ||
| 上 | 10mm 3/8-24UNF(Threaded | 1.5-10.0 | 100 | |
| 上 | 10mm M12x1.25(Threaded) | 1.5-10.0 | 100 | |
| 上 | 10mm B12(Taper Shank) | 1.5-10.0 | 100 | |
| 上 | 10mm 1/2-20UNF(Threaded) | 1.5-10.0 | 100 | |
| 上 | 13mm M12x1.25(Threaded) | 1.5-13.0 | 50 | |
| 13mm B16(Taper Shank) | 1.5-13.0 | 50 | ||
| 上 | 13mm 1/2-20UNF(Threaded) | 1.5-13.0 | 50 | |
| 16mm M12x1.25(Threaded) | 3.0-16.0 | 30 | ||
| 上 | 16mm B16(Taper Shank) | 3.0-16.0 | 30 | |
| 上 | 16mm B18(Taper Shank) | 3.0-16.0 | 30 | |
| 上 | 16mm 1/2-20UNF(Threaded) | 3.0-16.0 | 30 | |
| 16mm 5/8-16UN(Threaded) | 3.0-16.0 | 30 | ||
| (Keyless) | 10mm(Keyless) 3/8-24UNF(Threaded) | 0.8-10.0 | 50 | |
| (Keyless) | 10mm(Keyess) 1/2-20UNF(Threaded) | 0.8-10.0 | 50 | |
| (Keyless) | 10mm(Keyess) M12x1.25(Threaded) | 0.8-10.0 | 50 | |
| (Keyless) | 13mm(Keyless) 3/8-24UNF(Threaded) | 2.0-13.0 | 50 | |
| (Keyless) | 13mm(Keyless) 1/2-20UNF(Threaded) | 2.0-13.0 | 50 |
CHUCKADAPTER
TRIPOD
| Specification | PCS/CTN |
| SDS-PLUS1/2-20UNF | 400 |
| SDS-PLUS+1/2-20UNF | 40 |
| Name | Specification | PCS/CTN |
| Tripod | 1.2m | 25 |
| Tripod | 1.5m | 1 |
| DIARY | |
| ww/w.start-tools.com | |
WWW.START-TOOLS.COM
ADD: NO.1 GUANGPING ROAD, LIUHAO TOWN, HAIMEN CITY, NANTONG, JIANGSU PROVINCE, CHINA
POST CODE:226135
地址：江苏省南通市海门市海门刘浩乡工业园区广平路1号
TEL/FAX:0086-513-83292040
Email: Start-tools@foxmail.com
