该页无缩略图
ROTARYHAMMER INDUSTRIALGRADE
MACHINEPARTS
| 2470 | functions 4] | |
| MaxHole Opening | 最大钻孔直径 | |
| Concrete | 土 | 24 mm |
| Steel | 网材 | 13 mm |
| Wood | 木材 | 30 mm |
| No-load Speed | 空转 | 0-1100 rpm |
| ImpactTimes | 冷击频审 | 0-4500 bpm |
| Rated InputPower | 除入功率 | 780 W |
| Impact Energy Per Stroke | 击力 | 2.6 J |
T回
2470
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 35. | Impactor0-ring16.3x3.1冲击锤O型圈 | 1 | 70. | Field/Stator 定子 | 1 |
| 36. | Piston 活塞 | 1 | 71. | Motor Housing 机壳 | 1 |
| 37. | Washer 活塞销垫片 | 2 | 72. | Brand 商标 | 2 |
| 38. | Piston Pin 活塞销 | 1 | 73. | Carbon Brush Set 碳刷 | 2 |
| 39. | NeedleBearing HK3012轴承 | 1 | 74. | Switch 碳刷架 | 1 |
| 40. | SealO-ring 62x6.5 支架0型圈 | 1 | 75. | Switah 开关 | 1 |
| 41. | 606Bearing 606轴承 | 1 | 76. | Brand 商标 | 1 |
| 42 | Ring 6.7x1 中间轴扁卡簧 | 1 | 77. | Grommet 护套 | 1 |
| 43. | Spring 齿轮定位弹簧 | 1 | 78. | Cable 2x1mm 3.5m 电缆线 | 1 |
| 44. | Clutch 离合器 | 一 | 79. | Press Dable Board 压线板 | 1 |
| 45. | ToothedShaft 中间轴 | 1 | 80. | Screw ST4.2×22十字盘头自攻螺钉F型 | 4 |
| 46. | Drive EndShield 摆杆轴承 | 1 | 81. | Light 指示灯 | 1 |
| 47. | 26DensSlantingGear26牙斜齿轮 | 1 | 82. | Housing Cover 后盖 | 1 |
| 48. | Screw M4×14 内六角图柱头螺钉 | 2 | 85、 | Spring ①4开口卡簧 | 4 |
| 49. | End Shield 608轴承压板 | 1 | 86. | LimitedSleeve定位片塑料固定套 | 1 |
| 50. | InsulateRing8.4x13x2.5隔离圈 | 1 | 87. | LimitedSpring 定位片弹簧 | 1 |
| 51. | 608Bearing 608轴承 | 1 | 88. | Screw ST4.2×25十字盘头自攻螺钉F型 | 2 |
| 52. | BearingRing60B 轴承挡圈 | 1 | 89. | SpringLimited 离合齿轮定位片 | 1 |
| 53. | RetainingRing 扁卡簧 | 3 | 90. | Clutch Goar 离合齿轮 | 1 |
| 54 | ClutchLimitedSpring离合定位弹簧 | 1 | 91. | Washer 5.5×10x1 弹簧垫片 | 2 |
| 55. | ClutchLimitedKnob离合器定位块 | 1 | 92. | DepthGuage 标尺 | 1 |
| 56. | Intermediate Flange 支架 | 1 | 93. | Wire 0.5mm/105mm 接插线-白色 | 1 |
| 57. | Filter 羊毛毡 | 1 | 94. | Wire 0.5m/65mm 接插线-黑色 | 1 |
| 58. | BearingO-ring 6000轴承0型圈 | 1 | 95. | Plain Bearing 支架村套 | 1 |
| 59. | Shaft LipSeal 22x10x5 油封 | 1 | 96. | StraightPin离合器定位块定位销 | 2 |
| 60. | 6000Bearing 6000轴承 | 1 | 97. | Washer 齿轮定位弹簧垫片 | 1 |
| 61. | BearingWasher 6000轴承垫片 | 1 | 98. | Washer 8x4x1 垫片 | 2 |
| 63. | ArmaturoWithFan 转子 | 1 | |||
| 64. | Dust Proof Washer 防尘塑料垫片 | 1 | |||
| 65. | Bearing607 607轴承 | 1 | |||
| 66. | RotorSleeve 607轴承套 | 1 | |||
| 67. | ScrewST4.2x60十字盘头自攻螺钉F型 | 2 | |||
| 68. | Wire-pressedBoard定子定位压板 | 1 | |||
| 69. | Air-Deflector Ring 挡风板 | 1 |
ROTARYHAMMER INDUSTRIALGRADE
MACHINEPARTS
| DK25143 PECIF | functions3 | |
| MaxHoleOpening | 晨大钻孔直径 | |
| ICATI IDI Concrete | 26 mm | |
| Steel | 钢材 | 13 mm |
| Wood | 木材 | 30 mm |
| No-load Speed | 空载转速 | 0-1100 rpm |
| ImpactTimes | 冲击率 | 0-4900 bpm |
| Rated Input Power | 入功率 | 800 W |
| ImpactEnergy PerStroke | 击力 | 2.6 |
DK25143
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 32, | ImpactorO-ring①14x3冲击锤O型圈 | 1 | 62. | Bearing Sheath 607 | 轴承套 1 |
| 33. | Piston 活塞 | 1 | 63. | Field/Stator | 定子 1 |
| 34. | Washer 活塞销垫片 | 2 | 64. | Motor Housing | 机壳 1 |
| 35. | Piston Pin 活塞销 | 1 | 65. | Washer 607 轴承定位卡片 | 1 |
| 36. | Slidingasher27x31x2.6转套滑动垫圈 | 1 | 66. | Support Sleeve 手柄内定位套 | 1 |
| 37. | Screw M4x20 十字盘头螺丝 | 3 | 67. | Brush Plate 碳刷架 | 1 |
| 38. | O-ring 转套定位图 | 1 | 68. | Screw M3x8 十字盘头螺丝(F)型 | 2 |
| 39. | SealO-ring ①65x4 支架0型圈 | 1 | 69. | CarbonBrushSet6.2x7.9x14.6碳刷 | 2 |
| 40. | Intermediate Flange 支架 | 1 | 70. | CarbonBrushSpring碳刷窝型弹簧 | 2 |
| 41. | Washer6.2x10x1离合齿轮滑动垫片 | 1 | 71. | CannectingWire接插线0.5mx150mm（M+短） | 2 |
| 42. | CylindricalGear12牙中间轴离合齿轮 | 1 | 73. | Switch 开关 | 1 |
| 43. | Toothed Shaft 中间轴 | 1 | 74. | Press Cable Board 压线板 | 1 |
| 44. | Clutch 离合器 | 1 | 75. | Cable 电缆线 | 1 |
| 45. | DriveEndShield 摆杆轴承 | 1 | 76. | Grommet 护套 | 1 |
| 46. | Cylindrical Gear 27 牙斜齿轮 | 1 | 77. | Screw ST4.2x35 十字盘头螺丝 | 1 |
| 47. | Screw M4x10 十字盘头螺丝 | 2 | 78. | Housing Cover 后盖（左右） | 1 |
| 48. | End ShieId 轴承压板 | 1 | 79. | Sorew ST4.2×16 十字盘头螺丝 | 5 |
| 49. | Bearing608 轴承 | 1 | 80. | ClampingBand 手柄铁圈 | 1 |
| 50. | Screw M4x8 十字大扁头螺丝 | 1 | 81. | T-Head Bolt T型螺丝 | 1 |
| 51. | Straight Pin 拨叉定位柱 | 1 | 82. | Support Clamp 手柄座 | 1 |
| 52. | Switching Element 拨叉 | 1 | 83. | Depth Guage 标尺 | 1 |
| 53. | Torsion Spring 调挡扭簧 | 1 | 84. | Depth Guage Lock 标尺锁扣 | 1 |
| 54. | WoolFelt 羊毛毡 | 2 | 85. | Auxiliary Handle 辅助手柄 | 1 |
| 55. | 0-ringΦ21.5x2齿轮箱轴承0型圈 | 1 | 86. | M6Nut M6螺母 | 1 |
| 56. | Washer Bx17.5x1 608轴承垫片 | 1 | 87. | ScrewST4.2x45十字盘头螺丝（F型） | 1 |
| 57. | Bearing 608 轴承 | 1 | 88. | ScrewST3x16十字盘头螺丝（头部5.5） | 2 |
| 58. | Armature With Fan 转子 | 1 | |||
| 59. | Bearing 607 轴承 | 1 | |||
| 60. | Air-Deflector Ring 挡风板 | 1 | |||
| 61. | Cushioning 定子减震柱 | 2 |
ROTARYHAMMER INDUSTRIALGRADE
T回
| GBH2-20 functions2 |
| Max Hole Opening 最大钻孔直径 |
| Concrete 混凝士 20 mm |
| Steel 钢材 13 mm |
| Wood 木材 30 mm |
| No-load Speed 空载转速 0-850 rpm |
| ImpactTimes 冲击频率 0-3900 bpm |
| Rated InputPower 输入功率 500 W |
| Impact EnergyPerStroke 锤击力 1.7 |
MACHINE PARTS
GBH2-20
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 31. | Piston Pin 活塞销 | 61. | Housing Cover 后盖 | 1 | |
| 32. | SealO-ring 67x3 支架密封圈 | 1 | 62. | ScrewST4.2x22十字盘头自攻螺钉 | 1 |
| 33. | PlainBearing 支架衬套 | 1 | 63. | ScrewST4.2x16十字盘头自攻螺钉 | 2 |
| 34. | IntermediateFlange 支架 | 1 | 66. | Switch 开关 | 1 |
| 35. | 0-ringΦ23.2x2.4609轴承0型圈 | 67. | Cable 电源线 | 1 | |
| 36. | Ring 调档定位卡簧 | 1 | 68. | Grommet 护套 | 1 |
| 37. | 608Bearing 608轴承 | 7 | 69. | Press Cable Board 压线板 | 1 |
| 38. | 21densSlantingGear 21牙斜齿轮 | 70. | Clamping Band 手柄铁圈 | 1 | |
| 39. | Drive End Shield 摆杆轴承 | 71. | T-HeadBolt T型螺丝 | 1 | |
| 40. | Steel Ball C5钢珠 | 1 | 72. | BoltKnob 螺丝旋钮 | 1 |
| 41. | Toothed Shaft 中间轴 | 1 | 73. | Support Clamp 手柄座 | 1 |
| 42. | Springs 中间轴调位弹簧 | 74. | Depth Guage Lock 标尺锁盒 | ||
| 43. | Bracketoil Seal 中间轴销 | 75. | M6Nut M6螺母 | 1 | |
| 44. | WasherOfRollPin平面滚针垫片 | 1 | 76. | M8Nut M8螺母 | 1 |
| 45. | RollPin AXK0614平面滚针 | 1 | 77. | Auxiliary Handle 辅助手柄 | 1 |
| 46. | 609Bearing 609轴承 | 1 | 78. | Depth Guage 标尺 | 1 |
| 47. | ArmatureWithFan 转子 | 1 | 79. | Plastic Washer 隔离圈 | 1 |
| 48. | 607Bearing 607轴承 | 1 | 80. | Screw ST4x16十字盘头自攻螺钉 | 2 |
| 49. | Air-Deflector Ring 挡风板 | 1 | 81. | Washer 9.3×13x0.5 609轴承垫片 | 1 |
| 50. | ScrewST3.5x10十字盘头自攻螺钉 | 4 | 100. | Connection Wire 60mm 接插线 | 2 |
| 51. | Field/Stator 定子 | 1 | 101. | ConnectionWire 130mm 接插线 | 2 |
| 52. | BearingSleeve 607轴承套 | ||||
| 53. | Brand 商标 | ||||
| 54. | Brand 商标 | 1 | |||
| 55. | Sticker 铭牌 | ||||
| 56. | Brand 商标 | ||||
| 57. | Motor Housing 机壳 | 1 | |||
| 58. | Carbon Brush Set 5x8x16 碳刷 | 2 | |||
| 59 | Brush Plate 碳刷架 | 2 | |||
| 60. | Screw ST3x8 十字盘头自攻螺钉 | 4 |
ROTARYHAMMER INDUSTRIALGRADE
MACHINEPARTS
| GBH2-24 functions4 |
| Max Hole Opening 最大钻孔直径 |
| CAT Concrete 混凝士 24 mm |
| Steel 钢材 13 mm |
| Wood 木材 30 mm |
| No-load Speed 空载转速 0-870 rpm |
| ImpactTimes 冲击频率 0-4850 bpm |
| Rated InputPower 输入功率 620 W |
| Impact EnergyPerStroke 锤击力 2.6 |
T回A
GBH2-24
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 36. | HoldingJacket 限位套 | 1 | 70. | DatasPlate 铭牌 | 1 |
| 37. | Impactor 冲击锤 | 1 | 71. | Brand 商标 | 1 |
| 38. | ImpactorO-ringΦ15.1x3冲击锤0型圈 | 1 | 72. | BrushPlate 碳刷架 | 2 |
| 39 | Piston 活塞 | 1 | 73. | CarbonBrush Set5x8x17 碳刷 | 2 |
| 40. | Washer 活塞销垫片 | 2 | 74. | ScrewST3x8 十字盘头螺钉 | 4 |
| 41. | Piston Pin 活塞销 | 1 | 75. | Housing Cover 后盖 | 1 |
| 42. | PlainBearing 支架衬套 | 1 | 76. | ScrewST4.2x22一字梅花盘头螺钉 | 1 |
| 43. | Seal0-ring61x3 支架0型圈 | 1 | 77. | ScrewST4.2x16一字梅花盘头螺钉 | 2 |
| 44. | HoldingPlate 支架压叉 | 1 | 78. | Reverter 正反转开关 | 1 |
| 45. | IntermediateFlange 支架 | 1 | 79. | Screw 隔离圈 | 1 |
| 46. | 0-ringΦ23.2x2.4 609轴承0型圈 | 1 | 80. | washer9.3x13x0.5 609轴承垫片 | 1 |
| 47. | Heat-release Board 出风保护盖 | 1 | 81. | ScrewST4x16 十字盘头螺钉 | 2 |
| 48. | RubberWasher5x12.7x2 橡皮垫 | 1 | 82. | Cable 电源线 | 1 |
| 49. | Washer 凸型定位垫片（铁） | 1 | 83. | Grommet 护套 | 1 |
| 50. | SpringSeat(plastic) 弹簧座 | 1 | 84. | Press Cable Board 压线板 | 1 |
| 51. | CompressionSpring齿轮调位弹簧 | 1 | 85. | Clamping Band 手柄铁圈 | 1 |
| 52. | PlainBearingHK0609 滚针轴承 | 1 | 86. | T-HeadBolt T型螺丝 | 1 |
| 53. | 21densSlantingGear21牙斜齿轮 | 1 | 87. | Bolt Knob 螺丝旋钮 | 1 |
| 54. | Plain BearingK15 滚针轴承 | 1 | 88. | Support Clamp 手柄座 | 1 |
| 55. | Drive End Shield 摆杆轴承 | 1 | 89. | Depth Guage Lock 标尺锁盒 | 1 |
| 56. | PlainBearingHK0908 滚针轴承 | 1 | 90. | M6Nut M6螺母 | 1 |
| 57. | Ring 拨叉卡簧 | 1 | 91. | M8Nut M8螺母 | 1 |
| 58. | Switching Element 调档拨叉 | 1 | 92. | Auxiliary Handle 辅助手柄 | 1 |
| 59 | 699Bearing 699轴承 | 1 | 93. | Depth Guage 标尺 | 1 |
| 60. | Toothed Shaft 中间轴 | 1 | 94. | CarbonBrushSpring碳刷窝形弹簧 | 2 |
| 61. | 609Bearing 609轴承 | 1 | 95. | Inductance 电感 | 1 |
| 62. | ArmatureWithFan 转子 | 1 | 96. | Capacitor 电容 | 1 |
| 63. | 607Bearing 607轴承 | 1 | 100. | Connection Wire60mm 正反转接线 | 2 |
| 64. | Air-Deflector Ring 挡风板 | 1 | 102. | ConnectionWire130mm 接插线 | 2 |
| 65. | ScrewST3.5x10 十字盘头螺钉 | 4 | 103. | ConnectionWire98mm 正反转接线 | 2 |
| 66. | Field/Stator 定子 | 1 | |||
| 67. | BearingSleeve 607轴承套（F胶） | 1 | |||
| 68. | Brand 商标 | 1 | |||
| 69. | Motor Housing 机壳 | 1 |
ROTARYHAMMER INDUSTRIALGRADE
MACHINE PARTS
| GBH2-26 functions4 |
| MaxHoleOpening 最大钻孔直径 |
| Concrete 混凝士 26 mm |
| Steel 钢材 13 mm |
| Wood 木材 30 mm |
| No-load Speed 空载转速 0-1100 rpm |
| ImpactTimes 冲击频率 0-4900 bpm |
| RatedInputPower 输入功率 800 W |
| Impact Energy PerStroke锤击力 3.0 |
F回
GBH2-26
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 35. | Straight Pin 2.5x12定位销 | 3 | 69. | Plastic Washer 防尘塑料垫片 | 1 |
| 36. | Catch Disk 定位挡圈 | 1 | 70. | 607Bearing 607轴承 | 1 |
| 37. | RetainingRing28x1.5转套外钢丝卡簧 | 1 | 71. | Air-Deflector Ring 挡风板 | 1 |
| 38. | RetainingRingΦ27.5x1.5锤杆套定位钢丝卡簧 | 1 | 72. | Self-tappingScrewST3.5x14自攻螺钉 | 2 |
| 39. | Guide Bushing 锤杆套 | 1 | 73. | Field/Stator 定子总成 | 1 |
| 40. | O-ring 18x3.5 锤杆套0型圈 | 1 | 74. | Suppression Filter 电感组件 | 2 |
| 41. | O-ring Φ9.6x3.5 限位套0型圈 | 1 | 75. | Rubber Bushing 弹子套 | 1 |
| 42. | Holding Jacket 限位套 | 1 | 76. | Motor Housing 机壳 | 1 |
| 43. | RetainingRinge28x2转套内钢丝卡簧 | 1 | 77. | Switch Contact 铜簧插片 | 2 |
| 44. | Impactor 冲击锤 | 1 | 78. | Brush Plate 碳刷架 | 1 |
| 45. | Impactor0-ring中15.1x3冲击锤0型圈 | 1 | 79. | CarbonBrushSpring碳刷窝形弹簧 | 2 |
| 46. | Piston 活塞 | 1 | 80 | Carbon Brush Set 5x8x19碳刷 | 2 |
| 47. | Washer 活塞销垫片 | 2 | 81. | ConnectingWire定子插线98mm（两端M型） | 2 |
| 48. | Piston Pin 活塞销 | 1 | 82. | Switch 开关 | 1 |
| 49. | SealO-ring Φ53x7 支架0型圈 | 1 | 83. | Cable 电线2x1mm² | 1 |
| 50. | PlainBearing 支架衬套 | 1 | 85. | Grommet 整体护套 | 1 |
| 51. | IntermediateFlange 支架 | 1 | 86. | Press Cable Board 压线板 | 1 |
| 52. | HoldingPlate 支架压叉 | 1 | 87. | Self-tapping Screw ST4.2x22 自攻螺钉 | 1 |
| 53. | Bearing0-ring23.2x2.4609轴承0型圈 | 1 | 88. | Housing Cover 后盖 | 1 |
| 54. | 609Bearing 609轴承 | 1 | 89. | Clamping Band 手柄铁圈 | 1 |
| 55. | End Shield 609轴承压板 | 1 | 90. | T-HeadBolt T形螺丝 | 1 |
| 56 | Screw M4x10十字沉头螺丝 | 2 | 91. | Support Clamp 手柄座 | 1 |
| 57. | Toothed Shaft 中间轴 | 1 | 92. | DepthGuageLockSpring标尺锁扣弹簧 | 1 |
| 58. | 699Bearing 699轴承 | 1 | 93. | Depth Guage Lock 标尺锁盒 | 1 |
| 59. | SwitchingElement 调档拨叉 | 1 | 94. | Depth Guage 标尺 | 1 |
| 60. | SwitchingElementRing调档拨叉卡簧 | 1 | 95. | Auxiliary Handle 辅助手柄 | 1 |
| 61. | HK0910PlainBearing HK0910滚针 | 1 | 96. | M8Nut M8螺母 | 1 |
| 62. | Drive End Shield 摆杆轴承 | 1 | 97. | Self-tappingScrewST4.2x16盘头自攻螺钉 | 2 |
| 63. | K15Needle-Roller K15轴承 | 1 | 98. | Self-tappingScrewST4x16盘头自攻螺钉 | 2 |
| 64. | Dens Slanting Gear 33牙斜齿轮 | 1 | 99. | Toothed Shaft RetainingRing中间轴卡簧 | 1 |
| 65. | Compression Spring 齿轮调位弹簧 | 1 | 100. | bearingWasher9.3x13x0.5609轴承垫片 | 1 |
| 66. | SpringSeat（plastic）弹簧座（塑料） | 1 | 102. | ProtectiveCapWasher11x17x1防尘罩挡圈垫片 | 1 |
| 67. | Washer 凸型定位垫片 | 1 | |||
| 68. | ArmatureWithFan 转子总成 | 1 |
DEMOLITION HAMMER PROFESSIONAL
MACHINE PARTS
| GSH11DE |
| Rated InputPower 输入功率 1500 W |
| ImpactTimes 冲击频率 1100-2250 bpm |
| NetWeight 重量 11 kg |
一回
GSH11DE 零件表
| NO. | NAME | QTN | NAME | QTN |
| 44. Shim | 大伞形齿轮间隙调整片 | 1 | NO. 87. Brand | 机标 2 |
| 45. | Gear Z=49 大伞形齿轮 | 88. Motor Housing | 机壳 1 | |
| 46. | Gear Sleeve 花键套 | 1 | 89. Field/Stator | 定子 1 |
| 47. | Fork/SpringAssembly 调挡拨架 | 1 | 90. Spacer | 定子压位块 2 |
| 48. | Spring 拨架分离弹簧 | 1 | 91. CordClammp | 电缆压板 1 |
| 49. | Plate 花键套拨盘 | 1 | 92. Screw ST4.2x16 | 花形自攻螺钉F型 1 |
| 50. | Piston 活塞 | 1 | 93. BrushBracket | 碳刷架定位架 1 |
| 51. | WristPin 10.2x36.8 活塞销 | 1 | 94. BrushPlate | 碳刷架 2 |
| 52. | Connecting Rod 连杆 | 1 | 95. Screw ST3.5×10 | 十字盘头螺钉C型 5 |
| 53. | Screw M5×16 内六角圆柱头螺钉 | 4 | 96. Carbon Brush Spring | 蜗形弹簧 2 |
| 54. | Gear Sleeve 一级偏心从动齿轮 | 1 | 97. Carbon BrushSet | 碳刷 2 |
| 55. | GearPin 10×26.6 偏心固定销 | 1 | 98. Cable Socket | 电线插座 2 |
| 56. | BearingFlange 滚针支座 | 1 | 99. Brush Protect Point | 断电保护触点 1 |
| 57 | NeedleBearing NK1416滚针轴承 | 1 | 100. Screw60x80x1.5 | 垫片 1 |
| 58. | Retaining Ring 孔用挡圈22 | 1 | 101. Felt | 封油圈 1 |
| 59. | Washer 14x21.6x2.95 齿轮垫片 | 1 | 102. Cover | 头壳连接外罩 1 |
| 60. | IntermediateGear 二级主动齿轮 | 1 | 103. HousingCover | 齿轮箱盖 1 |
| 61. | Retaining Ring 轴用挡圈12 | 1 | 104. 0-ring24x3 | 调挡旋钮0型密封圈 1 |
| 62. | Needle Bearing NK1212滚针轴承 | 1 | 105. Selectorlron Core | 旋钮转换杆 1 |
| 63. | Gear Z=15 小伞形齿轮 | 1 | 106. Selector Pin | 调挡旋钮转换销 1 |
| 64. | Clutch Pin 6x6 过载离合轴销 | 8 | 107. SelectorKnob | 调挡旋钮 1 |
| 65. | Clutch Spring 过载离合弹簧 | 8 | 108. Selector Spring | 调挡弹簧 1 |
| 66. | Clutch 过载离合器 | 1 | 109. Selector RedKnob | 调挡红方块 1 |
| 67. | Eccentric Gear 二级减速从动齿轮 | 1 | 110. OilMouth 111. | 齿轮箱注油嘴 1 |
| 68. | NeedleBearing K141813滚针轴承 | 1 | Switch | 开关 1 |
| 69. | NeedleBearing K141810滚针轴承 | 1 | Speed Control | 恒速开关 1 |
| 70. | Needle BearingSleeve 滚针轴承套 | 1 | 113. SwitchHandle | 开关按钮 1 |
| 71. | Washer 15.35×22x1滚针轴承垫片 | 1 | 114. Handle | 手柄 1 |
| 72. | Bracket 齿轮箱定位小块 | 1 | 115. NeedleBearing HK1015 | 滚针轴承 1 |
| 73. | Gasket 齿轮箱密封圈 | 1 | 116. Light Conductor | 导光柱 1 |
| 74. | Screw ST6.3x30 外六角螺钉C型 | 4 | 117. Strain Relief | 护套 1 |
| 75. | NeedleBearing RNA4902 轴承 | 1 | 118. Cable2x1.5mm | 电线 1 |
| 76. | Seal 贮油圈 | 1 | 119. ClampAssembly | 手柄铁圈 1 |
| 77. | Grease Slinger 转子轴止油环 | 1 | 120. HandleClamp | 手柄塑料压板 1 |
| 78. 79. | Armature 转子 | 1 | 121. HandleBolt M8x50 | 手柄外六角螺栓 1 标尺 1 |
| 80. | Fan 风叶 | 1 | 122. DepthGauge | 螺丝旋钮 1 |
| ThreadedBushing 电机后轴承座 | 1 | 123. BoltKnob | 1 | |
| 81. | 6200Bearing 10×30x96200轴承 | 1 | 124. Clamp Holder | 手柄座 |
| 82. | O-ring 34x2 6200轴承0型密封圈 | 1 | 125. Depth Gauge Lock | 标尺锁扣 1 |
| 83. | Motor Housing Cover 机壳底盖 | 1 | 126. M6Nut | M6螺母 1 |
| 84. | Screw ST5.5×25 十字盘头螺钉C型 | 10 | 127. Auxiliary Handle | 辅助手柄 1 |
| 85. | Threaded Ring 后轴承压紧螺母 | 1 | 128. M8Nut | M8螺母 2 |
| 86. | Cap 压紧螺母塑料盖 | 2 | Handle Steel Ring | 10 轴用挡圈 1 |
| 129. 130 Rubber Cylinder | 4x8 弹性圆柱销 1 |
DEMOLITION HAMMER PROFESSIONAL
| GSH 11E | |
| Rated Input Power 输入功率 | 1500 W |
| ImpactTimes 冲击频率 | 0-1300 bpm |
| NetWeight 重量 | 11 kg |
| 1-回 | |
MACHINE PARTS
GSH11E
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 35. | Cap 齿轮箱盖防震圈 | 1 | 70. | Speed Control 恒速开关 | 1 |
| 36 | ScrewM5x12 内六角圆柱头螺钉 | 4 | 71. | Shift Plate 开关推板 | 1 |
| 37. | Gear Housing Cover 齿轮箱盖 | 1 | 72. | BallBearing 单列向心球轴承 | 1 |
| 38. | 0-Ring 84.2x2.6 曲轴盖0型圈 | 1 | 73. | Light Conductor 导光柱 | 1 |
| 39. | Gear 级从动齿轮轴 | 1 | 74. | Handle 大手柄 | 1 |
| 40. | Eccentric Gear 偏心齿销 | 1 | 75. | Screw M6x35 大平头十字螺钉 | 2 |
| 41. | Washer 17.2x29.8x1 齿轮垫片 | 2 | 76. | ScrewST4.2x16花型盘头自攻螺钉F型 | 1 |
| 42. | NeedleBearing16x22x16滚针轴承 | 2 | 77. | CordClamp 电缆压板 | 1 |
| 43. | NeedleBearingSleeve滚针轴承套 | 1 | 78. | Grommet 护套 | 1 |
| 45 | ScrewST6.3x30 外六角螺钉-C型 | 4 | 79. | Cable2x1.5mm² 电缆 | 1 |
| 46. | Impact Housing 齿轮箱 | 1 | 80. | BoltM8x130六角头螺栓C级对边13 | 1 |
| 47. | NeedleBearingRNA4902 轴承 | 1 | 81. | Catch Disc 辅助手柄固定块 | 2 |
| 48. | Seal 贮油圈 | 1 | 82. | ClampHolder 辅助手柄压块 | 2 |
| 49. | Motor Housing 机壳 | 1 | 83. | Clamp Assembly 手柄铁圈 | 1 |
| 50. | Stator 定子 | 1 | 84. | AuxiliaryHandle 辅助手柄 | 1 |
| 51. | LocatingPiece 定子塑料定位块 | 2 | 85. | Knob 小手柄调节钮 | 1 |
| 52. | BrushHolderAssembly刷架定位架 | 1 | 86. | M8Nut M8六角螺母（对边13） | 1 |
| 53. | BrushPlate 碳刷架 | 2 | 87. | Knob Cap 小手柄调节钮小盖 | 1 |
| 54. | Plug 电线插座 | 2 | 88. | Ring 轴用挡圈10 | 1 |
| 55. | ProtectContact碳刷断电保护触点 | 1 | 103. | BearingWasher 6200轴承垫片 | 1 |
| 56. | ScrewST3.5x10十字槽盘头螺钉c型 | 5 | |||
| 57. | CarbonBrushSpring碳刷蜗形弹簧 | 2 | |||
| 58. | Carbon Brush Set 碳刷 | 2 | |||
| 59. | Grease Slinger 转子轴止油环 | 1 | |||
| 60. | Armature WithFan 转子 | 1 | |||
| 61. | Threaded Bushing 电机后轴承座 | 1 | |||
| 62. | 6200Bearing 6200轴承 | 1 | |||
| 63. | O-Ring34x2 6200轴承0型圈 | 1 | |||
| 64. | Motor Housing Cover 机壳底盖 | 1 | |||
| 65. | ThreadedRing 后轴承压紧螺母 | 1 | |||
| 66. | Cap 压紧螺母塑料盖 | 1 | |||
| 67. | ScrewST5.5x25十字槽盘头螺钉c型 | 8 | |||
| 68 | Switch 开关 | 1 | |||
| 69. | Switch Actuator 开关压板 | 1 |
DEMOLITION HAMMER PROFESSIONAL
MACHINE PARTS
| GSH-11VC |
| Rated InputPower 输入功率 1700 W |
| ImpactTimes 冲击频率 900-1700 bpm |
| NetWeight 重量 11.1 kg |
GSH-11VC
零件表
| NO. | NAME | QTN | NO. | NAME QTN |
| 36. | 6300Bearing 6300轴承 | 72. Field/Stator | 定子 1 | |
| 37. | RetainingRing①35孔用挡圈A型 | 1 | 73. Lcover | 左盖板 1 |
| 38. | Washer 调速盖羊毛垫圈 | 1 | 74. Rcover | 右盖板 1 |
| 39. | 6004Bearing 6004轴承 | 1 | Carbon Brush | 碳刷 1 |
| 40. | Ring40 孔用卡簧B型 | 1 | BrushPlate | 刷架 2 |
| 41. | Gear Housing 齿轮箱 | 1 | ScrewST3.6x15平圆头花型螺钉F型 | 2 |
| 42. | CrclipΦ20 孔用挡圈B型 | 1 | Motor Housing | 机壳 4 |
| 43. | ScrewST6.1x30 盘头螺钉F型 | 4 | Air-Deflector Ring | 挡风板 1 |
| 44. | 6204Bearing 6204轴承 | 1 | Fan | 风叶 1 |
| 45. | 0-ringΦ20（外）大齿轮轴承0型圈 | 1 | Motor Housing Cover | 机壳底盖 1 |
| 46. | CylindricalGear 77牙大齿轮 | 1 | ScrewST5.1x25 盘头螺钉F型 | 1 |
| 47. | 0-ringΦ41（外）x2 活塞0型圈 | 1 | Switch | 开关 3 |
| 49. | Piston 活塞 | 1 | HandleCover | 1 |
| 50. | Piston Pin 活塞销 | 1 | 84. 85. Spring 手柄盖缓冲弹簧 | 1 |
| 51. | Washer 活塞销垫片 | 2 | Handle | 2 |
| 52. | Washer 连杆垫片 | 1 | ScrewST4.1x22手柄盘头螺钉F型 | 1 |
| 53. | NeedleBearing 滚针轴承 | 1 | ScrewST4.1x20 盘头螺钉F型 | 4 |
| 54. | Connecting Rod 连杆 | 1 | 89. Press CableBoard 压线板 | 1 |
| 55. | Crank Shaft Ass'y 偏心轴 | 1 | Grommet 电缆护套 | 1 |
| 56. | Sealing Ring 齿轮箱油封 | 1 | Cable | 1 |
| 57. | Brush Cover 齿轮箱盖 | 1 | Magnetic Circles 调速磁圈 | 1 |
| 58 | ScrewST6.1x20 手柄盖花形螺钉 | 1 | Pedestal 开关对插件 | 1 |
| 59. | FeltOil Seal 转子羊毛毡油封 | 6 | GearboxBaffle 齿轮箱盖挡板 | 1 |
| 60. | ScrewM5x20 圆柱头花型螺钉 | 1 | Corrugated Pipe 波纹管 | 1 |
| 61. | ScrewM5x20 法兰面花型螺钉 | 6 | Intermediate 手柄盖支架（左右） | 2 |
| 62. | Cover 调速盖 | 6 | Auxiliary Handle 辅助手柄 | 1 |
| 63. | M8Nut M8磁圈锁紧螺母 | 1 | CatchDisc 辅助手柄小件 | 1 |
| 64. | SealSC14x20x3 转子骨架油封 | 1 | ScrewM8x130 手柄螺丝 | 2 |
| 65. | Armature With Fan 转子 | 1 | ClampingBand 手柄铁圈 | 1 |
| 66. | Switch 调速开关 | 1 | 101 Clamp Holder 辅助手柄压块 | 1 |
| 67. | Switch Holder 开关固定座 | 1 | Knob辅助手柄调节钮组件（通用11E） | 2 |
| 68. | Cable Socket 定子电源进线插座 | 1 | 1 | |
| 69. | 6000Bearing 6000轴承 | 1 | ||
| 70. | Rotor Sleeve 轴承套 | 1 | ||
| 71. | Wire-pressedBoard 定子骨架 | 1 | ||
DEMOLITION HAMMER PROFESSIONAL
MACHINEPARTS
| 16-28 |
| Rated InputPower 输入功率 1750 W |
| ImpactTimes 冲击频率 0-1300 bpm |
| NetWeight 重量 16.5 kg |
| 28/30X410 |
16-28
零件表
| NO. | NAME | QTN | NO. NAME 74. | QTN |
| 38. | DeflatingValve 放气嘴 | 1 | Motor Housing 塑料机壳 | |
| 39. | Sealing Cover 油封盖 | 1 | 75. Base Plate 76. | 开关座 1 |
| 40. | 0-ring①85x3.5油封盖0型密封圈 | 1 | Switch | 开关 1 |
| 41. | Eccentric Shaft 曲轴 | SuppressionKit 防电波干扰电容 | 1 | |
| 42. | Gear Housing 齿轮箱 | 1 | 77. 78. Connecting Wire 连接电线 | |
| 43. | NeedleBearingRNA4904滚针轴承 | 1 | 79. Housing Cover 开关盖板 | 1 |
| 44. | Bearing20x47x146204单列向轴承 | 80. ScrewST4.2x22内六角圆柱螺钉F型 | 3 | |
| 45. | Crclip47 孔用挡圈47 | 1 | 81. CordClamp 电缆压板 | 1 |
| 46. | CylindricalGearZ=34二级从动齿轮 | 1 | 82. Grommet | 护套 1 |
| 47. | Brand 商标标签 | 1 | 83. Cable2x1.5mm² | 电缆 1 |
| 48. | CylindricalGearZ=16二级主动齿轮 | 1 | 84. Nut M10x1 六角薄螺母A级厚5 85. | 2 |
| 49. | CylindricalGearZ=47一级从动齿轮 | 1 | ScrewST6.3x20内六角花形螺钉F型 | 4 |
| 50. | NeedleBearing K121812滚针轴承 | 2 | ScrewST6.3x40内六角花形螺钉F型 | 2 |
| 51. | Space Tube 滚针轴承间隔垫 | 1 | BearindEndPlatel 定位小盖 | 1 |
| 52. | SealingFrame 齿轮箱盖封油垫 | BearindEndPlateI1 定位小盖 | 1 | |
| 53. | Toothed Shaft 中间轴 | Rubber Torsion Bar 花键组合件 | 2 | |
| 54. | Gear Cover 机壳端板 | 1 | BearingPedestal 大手柄定位座 | 1 |
| 55. | NutM12x1 六角薄螺母A级厚6 | 1 | Splineed Coupling 内外花键套 | 2 |
| 56. | Fan 风叶 | 1 | Supporting Disc 花键轴垫片 | 2 |
| 57. | ScrewST4.2x16一字平头螺钉F型 | 3 | Toothed Shaft 花键轴 | 2 |
| 58. | HoldingPlate 轴承闷盖 | 1 | Master Handle 大乎柄 | 1 |
| 59. | BearingWasher 6201轴承垫片 | 1 | Brand 机标 | 1 |
| 60. | 6201Bearing12x32x7 6201轴承 | BoltM8x130 六角头螺栓C级 | 1 | |
| 61. | BearingSeat 电机转子后轴承座圈 | Clamping Band 前手把抱箍 | 1 | |
| 62. | BrushHolder 风叶定位架 | 1 | ClampingPiece 小平柄定位座 | 2 |
| 63. | ScrewST3.5x10十字盘头螺钉C型 | 4 | Carrying Handle 小手柄 | 1 |
| 64. | Connector 电线插座 | 2 100. | Knob 小手柄调节钮 | 1 |
| 65. | Carbon Brush Set 碳刷 | 2 101. | Knob Cover 小手柄调节钮小盖 | |
| 66. | CarbonBrushSpring碳刷蜗形弹簧 | 2 102. | M8Nut M8六角螺母（对边13） | |
| 67. | BrushPlate 碳刷架 | 2 103. | NeedleBearing162216装满滚针 | |
| 68. | ArmatureWithFan 转子 | 1 104. | RetainingRing 轴用挡圈16 | 1 |
| 69. | ShaftLipSeal31x20x6 油封 | 1 105. | Washer16.5x24.1x0.5 连杆垫片 | |
| 70. | NeedleBearingRNA4902滚针轴承 | 1 | ||
| 71. | Spacer 定子压板 | 1 | ||
| 72. | ScrewST4.8x80 内六角螺钉C型 | 2 | ||
| 73. | Field/Stator 定子 | 1 |
DEMOLITION HAMMER PROFESSIONAL
| PH-65 |
| RatedInput Power 输入功率 1240 W |
| ImpactTimes 冲击频率 0-1400 bpm |
| NetWeight 重量 16.5 kg |
| 1回0 |
| NO. | NAME | QTN | NO. | NAME | QTN |
| 35. | Shaft Ring22 轴用挡圈22 | 73. | Cover Plate 封油盖 | 1 | |
| 36. | Final Gear 大齿轮 | 74. | Oil Gauge O-Ring 油标密封圈 | 1 | |
| 37. | Distance Ring 大齿轮距离套 | 75. | OilGauge 油标 | 1 | |
| 38. | 6201RZ BallBearing 6201RZ轴承 | 2 | 76. | Screw M5×12内六角圆柱头螺钉 | 9 |
| 39. | Counter Gear 小齿轮 | 1 | 77. | Tail Cover 底盖 | 1 |
| 40. | ScrewM5x12 沉头螺钉 | 3 | 78. | Supporting Disc 开关护套 | |
| 41. | Bearing Cover 6001RZ轴承压板 | 79. | SinglePoleSwitch 开关 | 1 | |
| 42. | 6001RZBallBearing 6001RZ轴承 | 1 | 80. | Handle 手柄 | |
| 43. | InnerCover 中间盖 | 1 | 81. | ScrewM6x25内六角圆柱头螺钉（带弹垫） | 4 |
| 44. | Seal Ring 中间盖密封圈 | 1 | 82. | Handle Cover 手柄盖 | 1 |
| 45. | Housing Cover 机壳 | 1 | 83. | CordClip 压线板 | 1 |
| 46. | ScrewM6x45内六角圆柱头螺钉（带弹垫+平垫） | 6 | 84. Cable | 3x1mm 电缆 | 1 |
| 49. | Bearing Cover 6203轴承压板 | 85. | Grommet 护套 | 1 | |
| 50. | Ball Bearing 6203RZ轴承 | 1 | 86. | Connector 圆接插片 | 3 |
| 51 | Fan Guide 挡风板 | 87. | ConnectingWire对接接插件（套） | 1 | |
| 52. | Armature With Fan 转子 | 88. Glip | 辅助手柄 | 1 | |
| 53. | Field/Stator 定子 | 1 | 89. | Side Handle 辅助手柄夹紧带 | 1 |
| 54. | ScrewM5x60十字盘头螺钉（带弹垫+平垫） | 2 | 90. Screw | M8x16 内六角螺钉 | 2 |
| 57. | Brush Terminal Ass'y 铜簧 | 2 | 91. NutM8 | 六角法兰面锁紧螺母 | 2 |
| 58. | Screw M5x8 内六角紧定螺钉 | 2 | 92. | Handle Stay 夹紧压片 | 1 |
| 59. | RubberWasher 碳刷绝缘垫圈 | 2 | 93. | Handle Shaft 手柄销 | 1 |
| 60. | Brush Holder 碳刷握 | 2 | 94. | Split Pin 3×30 开口销 | 2 |
| 61. | Carbon Brush 碳刷 | 2 | 95. Washer | 12垫片 | 2 |
| 62. | BrushCap 碳刷盖 | 2 | 96. Wrench | 油标扳手 | 1 |
| 63. | Cap Rubber 碳刷握橡胶垫 | 2 | 97. | Point Chisel 钻头 | 1 |
| 64. | Cap Cover 碳刷握压板 | 2 | 98. | Case Ass'y 工具箱 | 1 |
| 65. | ScrewM4x12十字带一字盘头螺钉（带弹垫+平垫） | 6 | 99. | 0ilFeeder 油壶 | 1 |
| 68. | Cover Seal 油盖密封垫 | ||||
| 69. | FeltHolder 油盖 | 1 | |||
| 70. | ScrewM4x10十字盘头螺钉（带弹垫+平垫） | 5 | |||
| 71. | 0ilFelt 油芯（羊毛毡） | 1 | |||
| 72. | Holder Seal 封油盖纸垫 | 1 |
DEMOLITION HAMMER PROFESSIONAL
MACHINE PARTS
| HM 1304 |
| Rated Input Power 输入功率 1500 W |
| ImpactTimes 冲击频率 0-1450 bpm |
| NetWeight 重量 15 kg |
| 1回0 |
HM1304
零件表
| NO. | NAME | QTN | NO. | NAME | QTN |
| 37. | SCREW ST6.3x38内六角螺钉 | 2 | 73. | 6202BEARING 6202轴承 | 1 |
| 38. | BIG GEAR 大齿轮距离套 | 1 | 74. | Fan Guide 挡风板 | 1 |
| 39. | 6205BEARING 6205轴承 | 1 | 75. | HEXBOLTM6x40内六角螺栓（带弹垫） | 4 |
| 40. | BEARING HOUSING 轴承室 | 1 | 76. | GEARBOXCOVER 齿轮箱盖 | 1 |
| 41. | BOLTSM6822内六角螺栓（带弹垫） | 4 | 77. | 6302BEARING 6302轴承 | 1 |
| 42. | FLATKEY4x4x12 | 平键 1 | 78. | 57DENSBIGGEAR 57牙大齿轮 | 1 |
| 43. | CRANK SHAFT | 曲轴 1 | 79. | SEALINGRINGI 中间盖密封圈！ | 1 |
| 44. | NEEDLEBEARINGNK16x16 滚针轴承 | 1 | 80. | MIDCOVER 中间盖 | 1 |
| 45. | CRANKSHAFTWASHER 曲轴垫片 | 1 | 81. | CordClip 压线板 | 1 |
| 46. | BOLTM6x18 内六角螺栓（带弹垫） | 1 | 82. | SEALINGRINGII中间盖密封圈I | 1 |
| 47. | 0-RINGΦ66.4x2 头壳0型圈 | 1 | 83. | SELFTAPPINGSCREWST4.3x22螺钉 | 3 |
| 48. | BRAND | 标签 1 | 84. | HANDLE COVER 手柄盖 | 1 |
| 49. | O-RING 加油密封盖0型圈 | 1 | 85. | SWITCH 开关 | 1 |
| 50. | Housing Cover 齿轮箱加油密封盖 | 1 | 86. | SWITCHPROTECTIVESLEEVE开关护套 | 1 |
| 51. | SCREWST4.8x16 十字自攻螺钉 | 6 | 87. | GEARBOXPOSITIONKEY齿轮箱定位销 | 2 |
| 52. | CAPRETAINER 碳刷盖压板 | 2 | 88. | RING 电机止油环 | 1 |
| 53. | RUBBER GASKET 碳刷盖橡皮垫 | 2 | 89. | 6001BEARING 6001轴承 | 1 |
| 54. | BRUSH CAP 碳刷盖 | 2 | 90. | 34DENSGEAR 34牙齿轮 | 1 |
| 55. | CARBON BRUSH 碳刷 | 2 | 91. | 6201 BEARING 6201轴承 | 1 |
| 56. | RETAINING RING 碳刷握挡圈 | 2 | 92. | HANDLE 手柄 | 1 |
| 57. | CapRubber 碳刷握橡皮护垫 | 2 | 93. | CAPACITY 0.1μF/250V 电容 | 1 |
| 58. | Brush holder 碳刷握 | 2 | 94. | SPONGE PAD 海绵垫 | 1 |
| 59. | PROTECTICESLEEVE 电源线护套 | 1 | 95. | LOCKINGSWITCH 自锁开关 | 1 |
| 60. | BACK COVER | 后盖 1 | 96. | SWITCHBUTTON 开关按钮 | 1 |
| 61. | SCREWM6x45内六角螺栓（带平、弹垫） | 6 | 97. | LOCKING PLATE 锁定板 | 1 |
| 62. | Cable 电源线 | 1 | 98. | SWITCH SPRING 开关弹簧 | 1 |
| 63. | GEARHOUSING | 机壳 1 | 99. | SCREWST4.2x16 十字自攻螺钉 | 2 |
| 64. | CRANKCASE 曲轴箱 | 1 | |||
| 65. | BRAND | 标签 1 | |||
| 66. | STATOR | 定子 1 | |||
| 67. | SCREWST4.8x65 十字自攻螺钉 | 2 | |||
| 68. | BEARING WASHER 6200轴承垫片 | 1 | |||
| 69. | 6200BEARING 6200轴承 | 1 | |||
| 70. | INSULATINGWASHER 绝缘垫圈 | 1 | |||
| 71. | ROTOR | 转子 1 | |||
| 72. | FAN | 风叶 1 |
