该页无缩略图
地弹簧尺寸配件图 Assembling picture of floor hinge series
(A)画线，使地弹簧转轴中心与门夹转轴重合。
(B)根据说明书和实物在地面开孔，孔的大细要与地弹簧壳体配紧，不能松动。 (C)将地弹簧放放开好的孔内，摆正。
(D)抬起装好门夹的门风扇，使地弹簧的转轴插入门扇的转动轴孔内。
(E)调节地弹簧三个方向的螺丝，保持门扇垂直，及上下转动轴重合。
(F)调节开门速度。
(G)盖上地弹簧装饰盖。
(A)Draw linesand make floor spring pivot center and door-nip pivot coincide witheach other. (B)Drillholesontheflooraccordingtotheinstructions,Thesizesoftheholesmusttightlymatchfloor spring.
(C)Place the floor spring into the holes and position it.
(D)Raise the doorleaf installed with door-nip,and insert the floor spring pivot into the hole fo the door leaf.
(E)Adjustthescrewsatthreedirections.Makethemverticalandtheupperandlowerpivotcenter coincide with each other.
(F) Adjustthe speedof door closing.
(G)Puthe decoration cover onthe floor spring
| 技术参数 | Technical parameters: |
| 力量级别 Power size | |
| 最大门宽(mm) | 1000 |
| Width of door max(mm) | |
| 最大门t(kgor max(kg) | 150 |
| 开门速eigsped | |
| 开p启n角gangle | 116° |
| 长/Length | |
| 铁壳尺寸(mm) | 282 130 |
| 宽/Width Dimension of cement box(mm) 高/Height | |
| 使用寿命 500,000次/Cycles | 64 |
地弹簧尺寸配件图 Assemblingpictureoffloor hinge series
(A)画线，使地弹簧转轴中心与门夹转轴重合。
(B)根据说明书和实物在地面开孔，孔的大细要与地弹簧壳体配紧，不能松动。 (C)将地弹簧放放开好的孔内，摆正。
(D)抬起装好门夹的门风扇，使地弹簧的转轴插入门扇的转动轴孔内。
(E)调节地弹簧三个方向的螺丝，保持门扇垂直，及上下转动轴重合。
(F)调节开门速度。
(G)盖上地弹簧装饰盖。
(A)Draw linesand make floor spring pivotcenterand door-nippivotcoincide witheach other. (B)Drillholesonthefloor according totheinstructions,Thesizesoftheholesmust tightlymatch floor spring.
(C)Place the floor spring into the holes and position it.
(D)Raise the door leaf installed with door-nip,and insert the floor spring pivot into the hole fo the door leaf.
(E)Adjust the screwsat three directions.Make them vertical andtheupper andlower pivotcenter coincidewitheachother.
(F)Adjustthespeedof doorclosing.
(G)Put the decoration cover onthe floor spring
| 技术参数 | Technical parameters: |
| 力量级别 Power size | |
| 最大门宽(mm) | 1000 |
| Width of door max(mm) | |
| 最大门重(kg) Weight of door max(kg) | 120 |
| 开门速pning speed | 二段 |
| 开启角度 Opening angle | |
| 长/Length | 116° 275 |
| 铁壳尺寸(mmementbox(mm) | |
| 宽/Width 125 | |
| 高/Height | 65 |
| Passed durability test 500,000次/Cycles | |
| 使用寿命 | |
(A)画线，使地弹簧转轴中心与门夹转轴重合。
(B)根据说明书和实物在地面开孔，孔的大细要与地弹簧壳体配紧，不能松动。 (C)将地弹簧放放开好的孔内，摆正。
(D)抬起装好门夹的门风扇，使地弹簧的转轴插入门扇的转动轴孔内。
(E)调节地弹簧三个方向的螺丝，保持门扇垂直，及上下转动轴重合。
(F)调节开门速度。
(G)盖上地弹簧装饰盖。
(A)Draw linesand make floor spring pivot center and door-nip pivot coincide witheach other. (B)Drillholesontheflooraccordingtotheinstructions,Thesizesoftheholesmusttightlymatchfloor spring.
(C)Place the floor spring into the holes and position it.
(D)Raise the doorleaf installed with door-nip,and insert the floor spring pivot into the hole fo the door leaf.
(E)Adjustthescrewsatthreedirections.Makethemverticalandtheupperandlowerpivotcenter coincide with each other.
(F) Adjustthe speedof door closing.
(G)Put the decoration cover onthe floor spring
| 技术参数 | Technicalparameters: |
| 力量级别 Power size | |
| 最大门宽(mm) | 1000 |
| Width of door max(mm) | |
| 最大门重（kg) Weight of door max(kg) | 120 |
| 开门速penigsped | |
| 开p启n角gangle | 116° |
| 长/Length | |
| 铁壳尺寸(mm) | 290 133 |
| 宽/Width Dimension of cement box(mm) | |
| 使用寿命 | 高/Height 50 |
地弹簧尺寸配件图 Assembling picture offloor hinge series
(A)画线，使地弹簧转轴中心与门夹转轴重合。
(B)根据说明书和实物在地面开孔，孔的大细要与地弹簧壳体配紧，不能松动。 (C)将地弹簧放放开好的孔内，摆正。
(D)抬起装好门夹的门风扇，使地弹簧的转轴插入门扇的转动轴孔内。
(E)调节地弹簧三个方向的螺丝，保持门扇垂直，及上下转动轴重合。
(F)调节开门速度。
(G)盖上地弹簧装饰盖。
(A)Draw linesand make floor spring pivotcenterand door-nippivot coincide witheach other. (B)Drillholesontheflooraccording totheinstructions,Thesizesoftheholesmust tightlymatch floor spring.
(C)Place the floor spring into the holes and position it.
(D)Raise the door leaf installed with door-nip,and insert the floor spring pivot into the hole fo the door leaf.
(E)Adjust thescrewsat three directions.Make them vertical andtheupper andlower pivotcenter coincidewitheachother.
(F)Adjustthespeedofdoorclosing.
(G)Put the decoration cover on the floor spring
Modelno:AC-533N
豪华耐用型 Luxuriousanddurable
| 技术参数 | Technical parameters: |
| 力量级别 Power size | |
| 最大门宽(mm) | 1200 |
| Width of door max(mm) | |
| 最大门重(kg) Weight of door max(kg) | 150 |
| 开门速pning speed | |
| 开启角gngle | 二段 116° |
| 长/Length | |
| 铁壳尺寸(mm) | 322 90 |
| 宽/Width Dimension of cement box(mm) | |
| 使用寿命 | 高/Height 48 |
地弹簧尺寸配件图 Assembling picture offloor hinge series
DOORCLOSER
非标淋浴房安装图
Nonstandardshowerroominstallationdiagram
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3.用户订购导轨时，我厂不包导轨钻孔，孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5.玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开，90°单开和180°
说明：1.以下淋浴房最大承重为：65KG
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum installation length is.1.8 meters, 90 degree double door unilateral maximum installation length 1 meters. 3. when users order the guideway, our factory does not pack guideway holes, and the holes need to be processed during construction. 4. the fittings of our factory are only suitable for clamping 8mm-10mm glass. 5.glass openings are strictly perforated according to the size of the installation drawings. 6.eachsection can be installed 90 degrees double open, 90 degrees single open and 180 degrees.
30×10方管带防跳杆平面安装图
30X10 installation of square pipe with jumping-proof pillar
30×10方管带防跳杆截面安装图
30X10Sectional installation of squarepipe with jumping-proof pillar
非标淋浴房安装图
Nonstandard shower room installationdiagram
说明：1.以下淋浴房最大承重为：65KG
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3．用户订购导轨时，我厂不包导轨钻孔，孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5.玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开，90°单开和180°
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum installation length is.1.8 meters, 90 degree double door unilateral maximum installation length 1 meters. 3. when users order the guideway, ourfactory does not pack guideway holes, and the holes need to be processed during construction. 4. the fittings of our factory are only suitable for clamping 8mm-10mm glass. 5.glass openings are strictly perforated according to the size of the installation drawings. 6.each section can be installed 90 degrees double open, 90 degrees single open and 180 degrees.
30X10方管带防跳杆平面安装图
30X10 installation of square pipe with jumping-proof pillar
30×10方管带防跳杆截面安装图
30X10Sectionalinstallationofsquarepipe with jumping-proof pillar
非标淋浴房安装图
Nonstandardshowerroom installationdiagram
说明：1．以下淋浴房最大承重为：65KG
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3．用户订购导轨时，我厂不包导轨钻孔，孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5.玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开，90°单开和180°
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum installation length is.1.8 meters,90 degree double door unilateral maximum installation length 1 meters, 3. when users order the guideway, our factory does not pack guideway holes, and the holes need to be processed during construction. 4. the fitings of our factory are only suitable for clamping 8mm-10mm glass. 5. glass openings are strictly perforated according to the size of the installation drawings. 6.each section can be installed 90 degrees double open,90 degrees single open and 180 degrees.
30×10方管带防跳杆平面安装图
30X10 installation of square pipe with jumping-proof pillar
非标淋浴房安装图
Nonstandard shower room installationdiagram
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3．用户订购导轨时，我厂不包导轨钻孔孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5.玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开,90°单开和180°
说明：1．以下淋浴房最大承重为：65KG
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum instalation length is.1.8 meters, 90 degree double door unilateral maximum installation length 1 meters. 3. when users order the guideway, ourfactory does not pack guideway holes, and the holes need to be processed during construction. 4. the fittings of our factory are only suitable for clamping 8mm-10mm glass. 5.glass openings are strictly perforated according to the size of the installation drawings. 6.eachsection can be installed 90 degrees double open, 90 degrees single open and 180 degrees.
25空心管带防跳杆平面安装图
25 hollow duct tape the jump bar plane installation drawing
非标淋浴房安装图
说明：1.以下淋浴房最大承重为：65KG
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3．用户订购导轨时，我厂不包导轨钻孔孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5．玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开，90°单开和180°
Nonstandardshowerroom installationdiagram
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum installation length is.1.8 meters, 90 degree double door unilateral maximum installation length 1 meters. 3. when users order the guideway, ourfactory does not pack guideway holes, and the holes need to be processed during construction. 4. the fittings of our factory are only suitable for clamping 8mm-10mm glass. 5.glass openings are strictly perforated according to the size of the installation drawings. 6.eachsection can be installed 90 degrees double open, 90 degrees single open and 180 degrees.
25空心管带防跳杆平面安装图
25 hollow duct tape the jump bar plane installation drawing
非标淋浴房安装图
说明：1.以下淋浴房最大承重为：65KG
2.180°最大安装长度为1.8米，90°双门单边最大安装长度1.0米
3．用户订购导轨时，我厂不包导轨钻孔孔需要施工时加工
4.本厂配件只适合夹8mm-10mm玻璃
5．玻璃开孔是，要严格按照安装图中的尺寸开孔
6.每款都可以安装90°双开，90°单开和180°
Nonstandardshowerroom installationdiagram
Instructions:1.the largest load of shower room is 65KG 2.180 degree maximum installation length is 1.8 meters, 90 degree double door unilateral maximum installation length 1 meters. 3. when users order the guideway, ourfactory does not pack guideway holes, and the holes need to be processed during construction. 4. the fitings of our factory are only suitable for clamping 8mm-10mm glass. 5. glass openings are strictly perforated according to the size of the installation drawings. 6.each section can be installed 90 degrees double open, 90 degrees single open and 180 degrees.
25空心管带防跳杆平面安装图
25 hollow duct tape the jump bar plane installation drawing
Glass door hanging wheel Model no:AC-A8001
Function // Size
Necessar fiting:
Glass door hanging wheel Model no:AC-A8002 Function//Size
Glassto glass Model no:YC-D4001
88000888 8-23
