CUT CUT RESISTANT GLOVES A665 VHR Advanced Cut Glove 144 13 ANSI CUT 12 ANSI/ISEA 105 EN 420 EN 388 EN 388:2016 ∙ ANSI cut level A6 ∙ Maximum EN cut protection levels ∙ Nitrile foam coating for excellent grip in wet and dry conditions ∙ Palm dipped to increase dexterity and ventilation ∙ Seamless 13 gauge liner HDPE, Glass fiber, Nitrile Foam Gray M-XXL EN388 EN388 ANSI 2003 2016 A6 4.5.4.4. 4.4.4.4.E. CUT A621 Cut 3/4 Nitrile Foam Glove 144 13 ANSI CUT 12 ANSI/ISEA 105 EN 420 EN 388 EN 388:2016 EN 407 ∙ ANSI cut level A3 ∙ Superb abrasion and tear resistance ∙ Nitrile foam coating for excellent grip in wet and dry conditions ∙ 3/4 dipped for increased protection ∙ 100% Breathable seamless liner HPPE, Glass fiber, Nitrile Foam Black M-3XL EN388 EN388 EN407 ANSI 2003 2016 A3 4.5.4.3. 4.4.4.3.D. X.1.X.X.X.X CUT Maximum Cut Protection 149

CUT CUT RESISTANT GLOVES A688 Pro Cut Liner Glove 144 13 ANSI 12 ANSI/ISEA 105 CUT EN 420, EN 388, EN 388:2016, EN 407 CE FOOD SAFE ∙ ANSI cut level A4, for superior protection ∙ Protection against high contact heat up to 212°F ∙ 100% Breathable seamless liner ∙ Low linting construction for minimal contamination HPPE EN388 EN388 ANSI Hi Vis Yellow 2016 2003 EN407 M-XXL A4 4.4.4.X.D. 4.5.4.X. X.1.X.X.X.X CUT A655 Sabre - Lite Glove 120 13 1 ANSI 12 ANSI/ISEA 105 CUT EN 420, EN 388, CE FOOD SAFE ∙ ANSI cut level A5 for superior cut resistance ∙ Ambidextrous and machine washable at 60C ∙ Sold singly HPPE, Steel Fiber, Polyester Blue S-XL Glove EN388 EN388 ANSI Length 12” 2003 2016 2.5.4.X. 3.4.4.X.D. A5 CUT A690 18 Inch (45cm) Cut Resistant Sleeve A691 22 Inch (56cm) Cut Resistant Sleeve A690 18 Inch (45cm) 192 13 1 ANSI CUT Cut Resistant Sleeve 12 A691 22 Inch (56cm) ANSI/ISEA 105 Cut Resistant Sleeve EN 420, EN 388, EN 388:2016, EN 407, CE FOOD SAFE ∙ Superior cut resistance EN388 EN388 EN407 ANSI ∙ Thumb hole for secure fit 2003 2016 ∙ Sold singly A4 HPPE Gray 4.5.4.X. 4.4.4.X.D. X.1.X.X.X.X CUT 150 Exceptional Cut Resistance

CUT HANDLE SHARP OBJECTS SAFELY A630 Razor - Lite Glove 120 13 ANSI CUT 12 ANSI/ISEA 105 EN 420 EN 388 EN 388:2016 EN 407 ∙ ANSI cut level A4, for superior protection ∙ Designed for tasks that require reinforced abrasion resistance ∙ Additional reinforced protection on palm and forefinger areas ∙ Low linting construction for minimal contamination ∙ Tested for both cut and heat protection HPPE, Glass fiber, Chrome Leather Gray M-XL EN388 EN388 EN407 ANSI 2003 2016 A4 4.5.4.2. 4.4.4.2.D. X.2.X.X.X.X CUT A640 Sabre-Dot Glove - PVC 144 13 ANSI CUT 12 ANSI/ISEA 105 EN 420 EN 388 EN 388:2016 EN 407 ∙ ANSI cut level A4 for superior protection ∙ PVC dotted palm for enhanced grip ∙ Protection against high contact heat up to 212°F ∙ Low linting construction for minimal contamination ∙ 13 gauge liner for a perfect fit HPPE, Glass fiber, PVC Gray S-XL EN388 EN388 EN407 ANSI 2003 2016 A4 2.5.4.2. 3.4.4.2.D. X.1.X.X.X.X. CUT Cut Resistance at Affordable Prices 151

GENERAL HANDLING - PU A120 PU Palm Glove Millions of ㎩irs Sold to Date 480 13 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 EN 388: 2016 ∙ Perfect for intricate tasks ∙ Maximum dexterity ∙ Smooth PU coating for increased abrasion resistance ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Pylon, PU WH - White XS-XXL BK - Black XS-XXL, GR - Gray XS-XXL O1 - Orange XS-XL Y2 - Yellow M-XL B4 - Blue M-XL P9 - Pink XS-L EN388 EN388 ANSI 2003 2016 A1 GR 4.1.3.1. 2.0.3.1.X. CUT VA120 432 24 Vending PU Palm Glove Gray XS-XL BK WH Y2 O1 B4 P9 Black S-XL AP80 Liquid Pro 216 13 ANSI 12 ANSI/ISEA 105 EN 420 , EN 388, EN 511 ∙ Latest in double coating technology ∙ Maximum liquid protection ∙ Smooth latex fully coated ∙ Second latex foam palm dip to give superior grip ∙ Elasticated wrist for a secure fit Waterproof Polyester, Latex, Latex Foam EN388 EN511 ANSI Grip Glove Blue M-XXL 2003 X.X.1. 3.1.3.1. 2 ABRASION 152 For Secure Grip, Comfort and Dexterity

GENERAL HANDLING - LATEX A100 Grip Glove - Latex 216 10 ANSI 12 ANSI/ISEA 105 GN EN 420 , EN 388 ∙ Premium quality work glove ∙ Ergonomic design to reduce hand fatigue ∙ Crinkle latex grip offers excellent grip ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Polyester, Cotton, Latex OR GN - Yellow/Green M-XXL OR - Yellow/Orange M-XXL EN388 ANSI 2003 3.2.4.2. 2 ABRASION A150 Fortis Grip Glove - Latex BEST VALUE 216 10 ANSI 12 ANSI/ISEA 105 EN 420 , EN 388 ∙ Very competitive price ∙ Environmentally friendly recycled yarns ∙ Crinkle latex grip offers excellent grip ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Polyester, Cotton, Latex OR - Yellow/Orange S-XXL EN388 ANSI 2003 1 2.1.2.1. ABRASION Recycled Cotton A340 Hi-Vis Grip Glove - Latex Foam Added Safety Feature - LONG CUFF 240 13 ANSI 12 ANSI/ISEA 105 EN 420 , EN 388 ∙ Highest levels of comfort from foam technology ∙ Latex foam coating for excellent grip in wet and dry conditions ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Nylon, Latex Foam Yellow M-XXL EN388 ANSI 2003 2.1.2.1. 2 ABRASION Best-Selling Grip Gloves 153

GENERAL HANDLING - NITRILE A300 Nitrile Knitwrist 144 12 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 Jersey l㏌ed ∙ Designed for applications that require additional abrasion resistance ∙ Prevents grease, oil and water penetration ∙ Smooth heavy nitrile coating ∙ Fully coated for maximum liquid protection ∙ Jersey cotton lining with knitwrist Cotton, Jersey Lining, Nitrile EN388 ANSI Navy M-XL 2003 3 4.1.2.2. ABRASION A301 Nitrile Safety Cuff Glove 144 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 ∙ Prevents grease, oil and water penetration ∙ Canvas safety cuff for added protection ∙ Smooth heavy nitrile coating ∙ 3/4 dipped for increased protection ∙ Open back for breathability Cotton, Nitrile EN388 ANSI Navy L, XL 2003 3 4.1.2.2. ABRASION A330 Nitrile Light Knitwrist 240 12 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 ∙ Lightweight abrasion resistant glove ∙ Maximum dexterity ∙ Smooth lightweight nitrile coating reduces hand fatigue ∙ 3/4 dipped for increased protection ∙ Open back for breathability Cotton, Nitrile EN388 ANSI Yellow M-XXL 2003 4.1.1.1. A1 CUT 154 Secure Grip in Wet and Dry Conditions

GENERAL HANDLING - NITRILE, PVC A350 DermiFlex Glove - PU/ Nitrile foam 360 15 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 , EN 388:2016 ∙ Maximum dexterity ∙ Protects against oil in warm and humid conditions ∙ PU/Nitrile blended foam coating for excellent grip in wet and dry conditions ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Nylon, Elastane, PU, Nitrile Foam EN388 EN388 ANSI Gray/Black M-XXL 2003 2016 A1 3.1.3.1. 4.1.3.1.X. CUT A351 PVC Palm Dots for DermiFlex Plus Glove - PU/ Nitrile foam Superior 360 15 ANSI Grip 12 ANSI/ISEA 105 EN 420, EN 388 EN 388:2016 ∙ Maximum EN level 4 abrasion ∙ Nitrile foam coating for excellent grip in wet and dry conditions ∙ Dotted palm for enhanced grip ∙ 15 gauge liner for extra dexterity ∙ Lightweight and comfortable Nylon, Elastane, PU, Nitrile Foam EN388 EN388 ANSI Gray/Black S-3XL 2003 2016 3.1.3.1. A1 4.1.3.1.X. CUT A352 3/4 Breathable DermiFlex Ultra Glove - PU/ Nitrile foam Nitrile Foam 360 Coating 12 15 ANSI ANSI/ISEA 105 EN 420, EN 388 EN 388:2016 ∙ Maximum dexterity ∙ Superb abrasion and tear resistance ∙ PU/Nitrile blended foam coating for excellent grip in wet and dry conditions ∙ 3/4 dipped for increased protection ∙ Open back for breathability Nylon, Elastane, PU, Nitrile Foam EN388 EN388 ANSI Gray/Black M-XXL 2003 2016 A1 3.1.3.1. 4.1.3.1.X. CUT Nitrile Coated for Enhanced Abrasion Resistance 155

GENERAL HANDLING - NITRILE A310 Flexo Grip Nitrile Glove 360 13 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 ∙ Ideal for auto repair, construction and other sectors ∙ Smooth nitrile coating for increased abrasion resistance Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Premium Pylon, Nitrile Nitrile White/Gray M-XXL COATING EN388 ANSI 2003 4.1.2.2. 2 ABRASION A315 All-Flex Grip Glove - Nitrile 360 13 ANSI 12 ANSI/ISEA 105 EN 420, EN 388 , EN 388:2016 ∙ Super lightweight glove ∙ Ergonomic design to reduce hand fatigue ∙ Smooth nitrile coating for increased abrasion resistance ∙ Fully coated for maximum liquid protection ∙ Elasticated wrist for a secure fit Pylon, Nitrile EN388 EN388 ANSI Black M-XXL 2003 2016 2.1.1.2. 3.1.2.1.X. 1 ABRASION A320 Dexti-Grip Glove - Nitrile Foam 360 13 ANSI 12 ANSI/ISEA 105 EN 420 , EN 388 ∙ Perfect for intricate tasks ∙ No 1. Choice for general assembly work ∙ Nitrile foam coating for excellent grip in wet and dry conditions ∙ Palm dipped to increase dexterity and ventilation ∙ 100% Breathable seamless liner Pylon, Nitrile Foam EN388 ANSI Black M-XXL 2003 3.1.3.1. 3 ABRASION 156 Flexo Grip for Superior Handling

CHEMICAL PROTECTION A810 Nitrosafe Chemical Gauntlet - Nitrile 192 12 EN 420, EN 388, EN 374-1 ∙ Chemical resistant gauntlet Textured ∙ Textured pattern for enhanced grip Palm and ∙ Smooth nitrile for enhanced chemical protection Fingertips ∙ Fully coated for maximum liquid protection ∙ Flock lined for added comfort Nitrile, Cotton EN388 EN374 EN374 CE Green S-XXL, 2003 CAT Length 320mm, III Thickness 0.38mm 2.0.0.1. A.J.K.L. A198 ESD - (Electrostatic Discharge) Antistatic Gloves Antistatic PU Fingertip Glove 480 13 ANSI 12 ANSI/ISEA 105 EN 420, EN 388, EN 388:2016, EN 1149 ∙ Diverts static electricity ∙ For use in electronics assembly, testing and precision work ∙ Smooth PU coating for increased abrasion resistance ∙ Fingertip dipped for precision handling and maximum ventilation ∙ 13 gauge pylon and carbon fiber shell Pylon, Carbon Fiber, PU Gray XXS-XXL EN388 EN388 2003 2016 EN1149 ANSI A1 2.1.3.2. 1.1.4.X.X CUT A199 Antistatic PU Palm Glove 480 13 ANSI 12 ANSI/ISEA 105 EN 420, EN 388, EN 388:2016, EN 1149 ∙ Diverts static electricity ∙ For use in electronics assembly, testing and precision work ∙ Smooth PU coating for increased abrasion resistance ∙ Palm dipped to increase dexterity and ventilation ∙ 13 gauge pylon and carbon fiber shell Pylon, Carbon Fiber, PU Gray XS-XXL EN388 EN388 EN1149 ANSI 2003 2016 A1 4.1.3.2. 3.1.2.1.X. CUT Specialist Hand Protection 157

PVC PALM DOTS FOR SUPERIOR GRIP A110 Polka Dot Glove 216 13 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 ∙ Performs well in dry conditions ∙ PVC dotted palm for enhanced grip ∙ Seamless 13 gauge liner ∙ 100% Breathable seamless liner Polyester, PVC Blue on White XS-XXL EN388 ANSI 2003 1 2.1.4.1. ABRASION A111 Fortis Polka Dot Glove 288 7 12 EN 420 CE CAT 1 ∙ PVC dotted palm for enhanced grip ∙ Lightweight and comfortable ∙ Performs well in dry conditions ∙ Excellent for jobs requiring high dexterity 65% Polyester, 35% Cotton, PVC Blue on White S-XXL PVC Palm Dots for Superior Grip 158 Best Selling Polka Dot Gloves

DRIVER AND RIGGER GLOVES A230 Best SELLER Double Palm Rigger Glove Reinforced 84 ANSI Patch Palm 12 ANSI/ISEA 105 EN 420 EN 388 EN 407 ∙ Superior double palm rigger ∙ Additional reinforced protection on palm and forefinger areas ∙ For use in construction, landscaping, agriculture and forestry ∙ Knuckle back protection ∙ Cotton backing for breathability Cow Split Leather, Cotton Chrome XL,3XL EN388 EN407 ANSI 2003 4.2.2.3. 2 4.3.X.X.X.X ABRASION A210 Canadian Rigger Glove 144 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 ∙ Patch palm and vein protection ∙ Cow split leather rigger ∙ Knuckle back protection ∙ Cotton backing for breathability Cow Split Leather, Cotton Gray XL EN388 ANSI 2003 2.2.3.3. 3 ABRASION Strong, Durable Rigger Gloves 159

DRIVER AND RIGGER GLOVES Luxurious, Soft and Warm Inner Fleece Lining A225 Fleece Lined Rigger Glove 72 ANSI 12 EN 420 EN 388 EN 511 ∙ Classic leather driver ∙ Specially designed for use in cold conditions ∙ Superb abrasion and tear resistance ∙ Fleece lined for added warmth Cow Split Leather, Insulatex Red XL I N S U L AT E X TM EN388 ermal Insulation 2003 EN511 2.2.4.3. X.3.X. LINING NOTE: INSULATEX is a trademark of Portwest. A220 Premium Chrome Rigger Glove 96 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 ∙ Premium split leather rigger ∙ Rubberized safety cuffs ∙ Knuckle back protection ∙ Cotton backing for breathability ∙ For use in construction, mining and landscaping Cow Split Leather, Polycotton Red/Gray XL EN388 ANSI 2003 3.1.2.3. 4 ABRASION 160 Market Leading Rigger Gloves

DRIVER AND RIGGER GLOVES A245 Antarctica Insulatex Glove 84 ANSI 12 EN 420 , EN 388, EN 511 ∙ Premium quality cow grain leather ∙ Knitwrist glove with Insulatex lining for enhanced warmth ∙ Suitable for coldstore applications Cow Grain Leather, Cotton, Insulatex EN511 Tan L,XL 1.2.0. EN388 2003 I N S U L AT E X TM 2.1.2.2. ermal Insulation A270 Classic Driver Glove 192 ANSI 12 ANSI/ISEA 105 EN 420, EN 388, EN 388: 2016 ∙ Classic leather driver ∙ Premium full grain cow leather ∙ Superb abrasion resistance ∙ Breathable leather for use in mild and hot climates Cow Grain Leather EN388 EN388 ANSI Tan L-XL 2003 2016 2.1.4.2. 2.1.4.2.X. 3 ABRASION A271 I N S U L AT E X TM ermal Insulation Lined Driver Glove 96 ANSI 12 ANSI/ISEA 105 EN 420 , EN 388, EN 511 ∙ Lined with Insulatex for cold conditions ∙ Classic leather driver ∙ Premium full grain cow leather ∙ Breathable leather for use in mild and hot climates Cow Grain Leather, Insulatex Tan L-XL EN388 EN511 ANSI 2003 X.2.X 2.1.4.2. 3 ABRASION Comfort You Can Really Feel 161

DRIVER AND RIGGER GLOVES A260 Oves Driver Glove 240 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 ∙ Classic leather driver ∙ Made from the softest sheep skin available ∙ Breathable leather for use in mild and hot climates ∙ Elasticated wrist for a secure fit Sheep Skin Gray M-XXL EN388 ANSI 2003 2.1.1.1. 3 ABRASION A251 Tergsus Micro Glove 180 ANSI 12 ANSI/ISEA 105 EN 420 EN 388 ∙ Synthetic microfiber palm with cotton backing for breathability ∙ Excellent for jobs requiring high dexterity ∙ Lightweight and comfortable ∙ Hook and loop strap for safe secure fit Microfibre, Cotton EN388 ANSI Blue M, Yellow L, Red XL, 2003 Black XXL 2 2.1.1.2. ABRASION 162 The Ultimate in Comfort and Protection

WELDING ㏚OTECTIVE GLOVES Industry Favorite A500 A530 Welders Gauntlet Reinforced Welding Gauntlet 60 ANSI 48 ANSI 6 6 ANSI/ISEA 105 ANSI/ISEA 105 EN 420 EN 420 EN 388 EN 388 EN 407 EN 12477 EN 12477 ∙ Maximum EN407 burn behavior resistance ∙ Premium quality leather welding gauntlet ∙ Ideal for welding and metal handling ∙ Fully welted and sewn with para-aramid thread ∙ 14” Cow split leather welding gauntlet ∙ Reinforced palm and thumb area ∙ Full cotton lining ∙ Full cotton lining Cow Split Leather, Cotton Cow Split Leather, Para-Aramid Red XL Brown XL EN388 EN12477 ANSI EN388 EN12477 ANSI 2003 EN407 TYPE A 2003 3 3.1.4.4. 4 3.2.3.3. 4.2.3.X.3.X. ABRASION TYPE A ABRASION Industry Leading Dexterity Welding Gauntlets 163

DISPOSABLE HAND PROTECTION MASSIVE A910 USA STOCK Powdered Latex Disposable Glove GMO 1x30 FREEFROM GENETICALLY MODIFIED CORN STARCH 100 EN 420 CE CAT 1 CE FOOD SAFE ∙ Manufactured from genuine natural rubber ∙ May cause allergic reactions in some individuals ∙ Highest degree of dexterity available ∙ Superior strength and comfort ∙ 100 gloves per box Latex White M-XL COLOR A925 3 Mil thickness Powder Free Nitrile Disposable Glove 1x30 100 EN 420 EN 374 CE FOOD SAFE ∙ 100% Latex free ∙ Highest degree of dexterity available ∙ Highly durable synthetic nitrile compound ∙ Textured pattern for enhanced grip ∙ 100 gloves per box ∙ 3mil thickness HIGHLY DURABLE Nitrile Blue M-XL Black M-XL SYNTHETIC NITRILE CE COMPOUND CAT III A.K.L. A.K.L. 164 Superior Comfort and Natural Fit

THE VEND READY PACKAGING SOLUTION  Save time and money  Improve usage monitoring and control  Improve inventory management  Improve restocking inefficiencies  Build your brand with customized packaging Front Back Vending styles VA120 152 VA620 147 VA622 147 Call today to talk to your local area sales representative 165

BizTex® Range BizTex® hazard protective clothing is an industry leading range of certified hazard protection garments that exceed the highest international standards. The BizTex range offers powerful protection against many workplace hazards. The Science Of Hazard Protection NOTE: BIZTEX IS A TRADEMARK OF PORTWEST. 166

ANSI/ISEA ANSI/ISEA 101 2014 Industries 101 and Hazards The purpose of this standard is to provide minimum size, packaging and labeling List requirements for limited-use and disposable coveralls. Aerospace EN 13982-1 EN ISO 13982: 2004 Type 5 EN 1149 EN 1149-5:2008 ST30 Agriculture \& Farming ST40 Asbestos Handling Dry particle suit (Type 5). Electrostatic requirements - Automotive This specifies the minimum surface resistivity. This tests for Bioengineering requirements for chemical the removal of electrostatic to Biological Hazards protective clothing resistant avoid sparks. Utilities to penetration by air borne Chemical Handling solid particles. Protects against Civil Protection hazardous dust and dry particles. Clean Room Construction EN 13034 EN 13034: 2005 Type 6 EN 14126 EN 14126: 2003 Decontamination Disease/Disaster Management Reduce spray suit (Type 6). This specifies the requirements Painting \& Decorating Performance requirements for and test methods for limited use Electronics chemical protective clothing protective clothing providing Engineering offering limited protective protection against infective Food Processing performance against liquid agents. Forensic Science chemicals (Type 6 and Type PB [6] Hazardous Materials equipment). Industrial Clean-Up and Maintenance Janitorial Chemical Protection NUCLEAR EN 1073-2: 2002 Medical PARTICLE Military Indicates compliance with current Protective clothing against Nuclear Industry radioactive contamination. Oil/Grease-Related Environments European standards for Chemical Requirements and test methods Oil \& Gas for non-ventilated protective Paint Handling/Isocyanate CHEMICAL Protective Clothing clothing against particulate Pharmaceutical PROTECTION radioactive contamination. Police Printing PHYSICAL BizTex SMS BizTex Powder Coating FABRIC TEST FABRIC MICROPOROUS Roof Insulation CLASS FABRIC CLASS Slaughterhouse The fabric used in these garments is designated BizTex SMS Veterinary Services fabric and BizTex Microporous fabric. 1 2 Warehousing Waste Management Abrasion EN530 Class 1 (min) - 6 (max) Resistance 167 Class 1 (min) - 5 (max) Flex Cracking ISO 7854 B Class 1 (min) - 5 (max) 45 Resistance Class 1 (min) - 5 (max) Class 1 (min) - 5 (max) Trapezoidal Tear ISO 9073-4 13 Resistant MD Class 1 (min) - 3 (max) Class 1 (min) - 5 (max) 21 ISO 9073-4 XD ISO 13934-1 21 MD Tensile Strength ISO 13934-1 XD 13 Resistance To EN132 74 - 4 Pass Pass Ignition Puncture EN863 11 Resistance 43 Stream Strength ISO 13935-2 CHEMICAL BizTex SMS FABRIC BizTex MICROPOROUS FABRIC TESTS FABRIC Resistance To Chemical Penetration EN368 Repellency Penetration Repellency Penetration Sulphuric Acid 30% - Class 1 (min) - 3 (max) Class Class Class Class Sodium Hydroxide 10% - Class 1 (min) - 3 (max) Isopropanol - Class 1 (min) - 3 (max) 3333 3333 0033

MICRO Fabric Information ANTI STATIC Portwest’s BizTex Micro fabric is a polypropylene substrate with anti- static properties to which a polyethylene film is applied (PP/PE). The outer layer prevents the passage of liquid molecules inwards yet allows the vapor molecules that build up on the inside of the fabric to permeate. This technology keeps the wearer fresh and comfortable. Anti-Static Breathable Protection Against Liquid Hazards ST40 BizTex Microporous Coverall Type 6/5 ANSI/ISEA 101 50 100% ANSI EN 1149 5 25 EN ISO 13982 TYPE 5 MANUFACTURER DECLARES EN 13034 TYPE 6 PRODUCT TESTED TO EN 14126 EN 1073-2 ∙ Excellent liquid and particulate barrier protection ∙ Durable and abrasion resistant ∙ Elasticated hood, ankles, cuffs and waist ∙ Two-way front zipper and sealable front flap ∙ Low linting construction ∙ Anti-static BizTex Microporous, 2.0oz White M-3XL ANSI / ISEA 101 CHEMICAL EN 13982-1 EN 13034 EN 1149 EN 14126 EN 1073-2 PROTECTION MICRO Accessories EN 13034 EN 13034 ST44 ST45 BizTex Microporous BizTex Microporous Boot Shoe Cover Type 6PB Cover Type 6PB 2EN 13034 TYPE 6 PB 200 100% 2EN 13034 TYPE 6 PB200 100% 25 25 ∙ Leading design made from microporous ∙ Leading design made from microporous material material ∙ Comfortable elastic closure for fit and ∙ Comfortable elastic closure for fit and protection protection ∙ Excellent protection from contaminants ∙ Excellent protection from contaminants BizTex Microporous, 2.0oz BizTex Microporous, 2.0oz White One Size White One Size 168 Exceptional Strength with Superior Barrier Protection

SMS Fabric Information ANTI STATIC Portwest’s SMS is an integrated three layer polypropylene construction with anti-static properties. Formed by layering spunbond, meltblown and spunbond, the fabric is strong and durable as well as being soft and breathable. Strong Breathable Protection Against Hazardous Dry Particles ST30 BizTex SMS Coverall Type 5/6 ANSI/ISEA 101 50 100% ANSI EN 1149 5 25 EN ISO 13982 TYPE 5 EN 13034 TYPE 6 EN 1073-2 ∙ Highly breathable SMS fabric MANUFACTURER DECLARES ∙ Provides an effective barrier against PRODUCT TESTED TO particulates, aerosols and light sprays ∙ Elasticated hood, ankles, cuffs and waist ∙ Two-way front zipper and sealable front flap ∙ Anti-static BizTex SMS, 1.5oz White M-3XL ANSI / ISEA 101 CHEMICAL EN 13982-1 EN 13034 EN 1149 EN 1073-2 PROTECTION Portwest BizTex SMS Spunbond products are manufactured Meltblown with an integrated three layer SPUNBOND polypropylene construction: Fluid and • SPUNBOND Particulate • MELTBLOWN • SPUNBOND Barrier Highly Breathable The high tensile strength offered by this trilaminate fabric protects the wearer from fluid and particulate penetration without compromising on mobility or comfort. Ideal Protection Against Chemical Hazards 169

PS53 174 PS11 179 USA Head Protection Range UC496 76 Portwest’s rapidly expanding head protection product range aims to benefit our customers by combining the most up to date styles and standards in head protection, irrespective of job or location. Innovative, comfortable and lightweight hard hats are available for a multiple use. 170

USA Standards MAKING SAFETY THE TOP PRIORITY ANSI/ISEA Z89.1: 2014 employee when near exposed electrical conductors TYPE I - Hard hats are designed only to withstand American National Standard for which could contact the head. top impacts. Industrial Head Protection The performance criteria for head protection is provided in the American National Standards TYPE II - Hard hats designed to withstand impacts The Occupational Safety and Health Administration Institute (ANSI) Z89.1 American National Standard from the top and the side. (OSHA) guidelines state that employees shall wear for Industrial Head Protection, updated in 2014. protective hard hats when working in areas where Class C - Conductive Hard Hat = the hard hat will there is a potential for injury to the head from not protect the wearer from electrical hazards. falling objects. Protective hard hats designed to reduce electrical shock hazard shall be worn by each Class G - General Hard Hat = hard hat that can withstand an electrical current up to 2,200 volts. Class E - Electrical Hard Hat = hard hat that provides the highest level of electrical protection, withstanding currents up to 20,000 volts. Hard hats classification and markings based on ANSI Z89.1: 2014 Classification Marking Definitions IMPACT TYPE TYPE I TYPE I Hard hats designed to reduce the force of impact resulting from a blow only to the top of the head TYPE II TYPE II Hard hats designed to reduce the force of impact resulting from a blow to the top or sides of the head ELECTRICAL Class G (General) Class G Hard hats designed to reduce the danger of contact with low-voltage conductors. Tested at 2,200 volts CLASS Class E (Electrical) Class E Designed to reduce the danger of contact with conductors at higher voltage levels. Tested at 20,000 volts Class C (Conductive) Class C Hard Hats intended to provide no protection against contact with electrical hazards OPTIONAL Reverse Donning Hard hats which can be worn frontward or backward. They pass all hard hat testing requirements, whether worn frontward or REQUIREMENTS backward Lower Temperature LT Hard hats meet all testing requirements of the standard when preconditioned at a temperature of -30°C (-22°F) High Visibility HV Indicate that the hard hat meets all testing requirements of the standard for high visibility colors. This includes tests for chromaticity and luminescence Higher Temperature HT Hard hats meet the performance criteria after being preconditioned to higher temperatures of 140ºF(60ºC) EN 397: 2012 from 1m height) must not come into contact with Optional tests: Industrial Safety Hard Hats the skull. • Resistance at extreme temperatures: Mandatory tests: • Flammability: The hard hat is exposed to a flame • Impact: Energy spread to the head form must not and it must not burn with flame emission more than Testing impact and penetration are performed at exceed 5 kN after the fall of an object of 5 kg at 1m 5 seconds after removal of the flame. +150 °C, -20°C or -30 °C temperatures. high. Impact and penetration tests are performed at • Electrical properties: • Penetration: The tip of the test mass used (3 kg room temperature, +50 °C and at -10°C. Protects against a short accidental contact with electric leads under voltage up to 440 V. The Premier USA Brand in Head Protection 171

P AKVIEW SMOKE TTRRAANN SS LL U C EE NNTT HHAERLDM HE AT T BLUE CLEAR YELLOW GREEN 4 8X STYLES X COLORS RED ORANGE The Peak View Hard Hat is a Portwest exclusive design. The translucent shell and see through peak and sides allow the wearer to look upwards without the need to tilt the head. The extra strong yet ultra light weight polycarbonate shell offers UV ray protection. This innovative, market leading design is available in 4 style options that come in 8 color ways. Peak View is the safest and most comfortable solution for your head protection. PINK 172 Exclusive Innovative Design by Portwest

P AKVIEW T R A N S L U C E N T HARD H AT TRANSLUCENT HELMET 1 PV50 Peak View Hard Hat - Vented 20 ANSI ANSI/ISEA Z89.1 TYPE II C EN 397 ∙ Portwest exclusive design ∙ Translucent shell to see through peak and sides ∙ Extra strong yet ultra lightweight Polycarbonate shell, offering UV 400 protection ∙ 6 points textile harness, adjustable size ∙ Vented shell for extra air-flow (PV50) 2 100% Polycarbonate PV50 Smoke, Blue, Clear, Yellow, Green, Red, Orange, Pink Adjustable 19.6”-26” Soft foam sweat band PV54 included Peak View Plus Hard Hat - Non 6 points Vented textile harness 20 ANSI ADJUSTABLE SLIP RATCHET ANSI/ISEA Z89.1 TYPE II CLASS G EN 397 440 V.A.C. 100% Polycarbonate Smoke, Blue, Clear, Yellow, Green, Red, Orange, Pink Adjustable 19.6”-26” 3 PV60 ADJUSTABLE WHEEL RATCHET Peak View Ratchet Hard Hat Vented 20 ANSI ANSI/ISEA Z89.1 TYPE II CLASS C EN 397 ∙ Portwest exclusive design ∙ Translucent shell and see through peak and sides allow the wearer to look upwards without the need to tilt the head ∙ Extra strong yet ultra light weight polycarbonate shell offers UV rays protection ∙ 6 points textile harness ∙ Wheel ratchet adjustment ∙ Vented shell for extra air-flow (PV60) 100% Polycarbonate Smoke, Blue, Clear, Yellow, Green, Red, Orange, Pink Adjustable 19.6”-26” 4 PV64 PV60 Peak View Plus Ratchet Hard Hat - Non Vented Soft foam 20 ANSI sweat band included ANSI/ISEA Z89.1 TYPE II CLASS G EN 397 V.A.C. 6 points textile harness 100% Polycarbonate Smoke, Blue, Clear, Yellow, Green, Red, Orange, Pink 173 Adjustable 19.6”-26” COMPATIBLE ACCESSORIES AVAIL ABLE SEE PAGE 176

HEAD PROTECTION PS52 PW Full Brim Future Vented for Extra 20 ANSI Air-flow ANSI/ISEA Z89.1 TYPE I CLASS E Vented for Extra Air-flow EN 397 -10°C/+50°C 174 Vented hard hat allowing a refreshing ∙ Full Brim hard hat airflow around the head ∙ Wide profile provides extra protection against sun, glare, rain, debris and non-toxic splashes ∙ 4 points nylon harness with wheel adjustable ratchet ∙ Soft foam sweat band included PP White Adjustable 20.4”-24.8” PW52 Full Brim Future Vented 20 ANSI ANSI/ISEA Z89.1 TYPE I CLASS C ∙ Full brim hard hat with vented holes for ultimate wearer comfort in hot conditions ∙ HDPE shell, 4 points textile comfort harness ∙ Wheel ratchet adjustment ∙ Soft foam sweat band and 4 points chin strap included HDPE Adjustable 20.5”-24.8” Yellow, White PS53 Height Endurance Hard Hat 20 ANSI ANSI/ISEA Z89.1 TYPE I CLASS E EN 397 -30°C/+50°C, EN 50365 CLASS:0 ∙ Hi-Visibility color for increased visibility ∙ Light, comfortable and compact with a short peak ∙ ABS shell, 4 points textile comfort harness ∙ Technical sweat band and 4 points chin strap (Y style) with a soft rubber chin protector included ABS Hi-Vis Orange, Hi-Vis Yellow, White Adjustable 20.5”-24.4” PS50 Arrow Safety Hard Hat 50 ANSI ANSI/ISEA Z89.1 TYPE I CLASS C EN 397 -10°C/+50°C ∙ Lightweight vented hard hat with 8 vent ports allowing total airflow circulation around the head area ∙ 6 points PE suspension harness for a comfortable fit ∙ Buckle size adjustment for easy fitting ∙ Compatible with PW47 and PS47 clip-on ear muffs ∙ Foam sweat band included HDPE, PE Blue, White, Yellow Adjustable 20.9”-25.6”

PW98 Forestry Combi Kit Vented for Extra Air-flow IMPROVED 12 LD ANSI/ISEA Z89.1 TYPE I CLASS C ANSI/ISEA Z87.1 (VISOR HOLDER + MESH VISOR) ANSI S3.19 NRR NRR 24DB (EAR MUFF) EN 397 -30°C/+50°C, LD,EN 352-3 ,EN 1731 F ∙ Professional combi kit containing a hard hat, clip-on ear muffs and mesh visor ∙ Vented ABS safety helmet with wheel ratchet adjustment (PS55) ∙ High performance ear muffs in ABS material, adjustable in height for a better fit (PW47) ABS, Mesh, Polystyrene Orange Adjustable 22.1”-24.8” PS59 AirTech Bump Cap 60 10 EN 812 ∙ Hi-Visibility color for increased visibility ∙ Inner ABS shell and soft pad for shock absorption ∙ Innovative design bump cap with side mesh for maximum ventilation. ∙ Mid-length peak (1.97”) ideal for all uses indoor and outdoor ∙ Buckle size adjustment for easy fitting 100% Nylon, ABS, EVA Hi-Vis Yellow Adjustable 21.3”-23.2” PA10 Hard Hat Holder 40 ∙ The hard hat holder is a Portwest exclusive design to keep your hard hat safe and secure ∙ High performance magnets for attaching to metal surfaces and screws to attach to timber or plaster board surfaces ∙ In built safety spectacle holder ∙ Suitable for most standard type hard hats ∙ UV stabilized for outdoor use 100% Polypropylene Yellow One Size PA58 Helmet Winter Liner IDEAL FOR COLD 50 WEATHER 10 175 ∙ 100% Cotton insulating liner ∙ Designed to be worn with all hard hats ∙ Hook \& Loop straps to attach to the inner hard hat ensuring a secure fit ∙ Can be worn with a chin strap 100% Cotton Black, One Size

ACCESSORIES PW58 PW96 PW99 Hard Hat Visor Carrier Face Shield Plus Replacement Shield 80 24 MM ANSI Plus Visor 20 ANSI/ISEA Z87+ MM140 ANSI EN 166 EN 166 1 BT 3 9 EN 1731 10 ∙ Universal hard hat visor holder PW99 ∙ Browguard including clear polycarbonate visor ANSI/ISEA Z87+ with aluminum edge EN 166 1 BT 3 9 ∙ Compatible with PS50 hard hat and PW99 visor ∙ Superior front and side face protection ∙ Replacement visor to be used on PW96 browguard support ∙ The holder’s upwards movement ∙ Protects from impacts, metal splashes and hot enables stand-off visor position solid projections ∙ Polycarbonate clear visor with aluminum edge for intermittent use ∙ Harness ratchet adjustment for comfort fit ∙ Protects from impacts,metal splashes and Polyoxymethylene hot solids projections Black ∙ Replacement visor available (PW99) PS50 Polycarbonate, Aluminum Polycarbonate, Aluminum Clear 7.9” X 15.7” Clear 7.9” X 15.7” PA91 PW53 ID12 Reflective Stickers Pack Chin Strap Medical Information Contact X2 X10 X30 X10 800 10 10 100 ∙ High quality reflective stickers for safety helmets ∙ Nylon woven strap with PP chin cup ∙ Water resistant holder with waterproof paper ∙ Honeycomb pattern with excellent reflective quality ∙ Helps hard hats secure fit while working ∙ Instant user/wearer recognition ∙ Easily to clip on and compatible with PV50/ ∙ Information is held securely to improve visibility and safety ∙ Write on both sides to include more ∙ Cutting-edge design suitable for all hard hat styles PV54, PV60/PV64 hard hats ∙ Each pack (for 1 helmet) contains 7 stickers information ∙ UOS is 10 packs (for 10 helmets) containing 70 PET ∙ Language free Black stickers PVC Red 2.7” X 0.8” PET Silver, Red 5.9” x 5.9”

Respiratory Range Our Biztex® brand ensures exceptional quality and performance across our full range of disposable masks. The Biztex range offers a high level of protection and quality safeguarding the wearer against many workplace risks. Certified to NIOSH and EN 149 standards. BIZTEX is a trademark of Portwest. NIOSH Standard: 42 CFR Part 84 classifies particulate respirators into nine different classes broken down into three levels of filter efficiency (95, 99 and 99.97%) and three categories of filter degradation (N, R and P). The selection of N-, R- and P-series filters depends on the presence or absence of oil particles. If no oil particles are present then any series filters (N-, R- or P-series) may be used. If oil particles are present then either an R- or P-series filters may be used. If oil particles are present and the filter is to be used for more than one work shift, then only a P-series filter may be used. N-series filters cannot be used if oil particles are present. The table below summarizes the difference between the NIOSH 42 CFR Part 84 and CE EN 149:2001 + A1:2009 standards. Standard Classification of the Efficiency Breathing Resistance Total Inward Categories of Resistance Leakage Filters Level (Inhalation) N95/R95/P95 95% N Series - Used in particulate environments free of oil aerosols NIOSH N99/R99/P99 99% 85L/Min Not tested R Series - Used for oil \& non oil particles aerosol (with time use 42CFR-84 N100/R100/P100 99.97% 3,42 mbar limitations specified by NIOSH) P Series - Used for oil \& non oil particles aerosol ( with time use limitations specified by manufacturer) EN149:2001 FFP1 ≥80% 95L/Min P1 = 78% All masks can be used against oil \& non oil particulate aerosols + A1:2009 FFP2 ≥94% P2 = 92% FFP3 ≥99% FFP1: 2,1 mbar P3 = 98% FFP2: 2,4 mbar FFP3: 3,0 mbar Based on efficiency level, FFP2 filters protection level is approximately equal to that of ANSI R95 level. LATEX LATEX FREE FREE P200 N95 Cup Respirator P201 N95 Cup Valved Respirator X30 X30 20 10 NIOSH N95 NIOSH N95 EN 149 FFP2 NR EN 149 FFP2 NR ∙ N95 approved offering protection against a wide range of non- ∙ N95 approved offering protection against a wide range of non-oily particles oily particles ∙ Provides 95% NIOSH filtration efficiency ∙ Cup style for maximized inner space ∙ Provides 95% NIOSH filtration efficiency ∙ Exhalation valve to reduce heat and humidity whilst offering a lighter ∙ Cup style for maximized inner space ∙ Welded straps attachment for greater durability breathing resistance Polypropylene Polypropylene White White One size One size 177

CUESRA TSITFAINEDDARTDOS MANUFACTURER DECLARES PRODUCT TESTED TO Eye Protection Range USA Standards ANSI/ISEA Z87.1: 2015 ANSI Z87.1: 2015 markings American National Standard - Marking Meaning Position Personal Eye and Face Protective PW: Portwest Manufacturer Identification Frame \& Lens Devices. Z87 Non Impact protector Frame \& Lens OPTIONAL MARKINGS Meaning Position ANSI Z87.1 sets forth criteria related Required only when impact rating is to the general requirements, testing, claimed by the manufacturer Impact protector Frames used for an impact-rated permanent marking, selection, care and Z87+ Meaning protector are marked with Z87 + use of protectors to minimize or prevent (lenses show just a “ +” symbol) injuries from such hazards as impact, OPTIONAL MARKINGS non-ionizing radiation, and chemical Required only when special lens/use Position exposures in occupational and educational is claimed by the manufacturer environments including, but not limited to, -(no marking) Lens type - Clear Lens machinery operations, material welding W - followed by shade number Lens type - Welding Lens and cutting, chemical handling, and U and scale number* Lens type - UV filter Lens assembly operations. The most recent L and scale number* Lens type - Visible light filter Lens update of ANSI Z87.1 was established in R and scale number Lens type - IR filter Lens 2015. The new standard is focused on the V Lens type - Variable Tint Lens hazards and is organized so that users can S Lens type - Special Purpose Frame seek guidance by type of hazard, such as D3 Splash/Droplet Frame impact, optical radiation, splash, fine dust D4 Dust Frame and mist. D5 Fine Dust 178 USA Standards for Personal Eye Protection

* = see tables below for more details on U marking PREMIUM (UV filters performances) and L marking (Visible Light PROTECTION Filters performances) Transmittance requirements for Visible Light Filters: Transmittance requirements for Ultraviolet Filters: Scale (Marking) Maximum % Nominal % Minimum % Scale Maximum effective Far- Maximum effective Near- L1.3 85 74.5 67 (Marking) Ultra-Violet (200-315nm) Ultra-Violet (325-380nm) L1.5 67 61.5 55 Average transmittance % Average transmittance % L1.7 55 50.1 43 U2 L2 43 37.3 29 U2.5 0.1 3.7 L2.5 29 22.8 18 U3 0.1 2.3 L3 18 13.9 8.5 U4 0.07 1.4 L4 8.5 5.18 3.16 U5 0.04 0.5 L5 3.16 1.93 1.18 U6 0.02 0.2 L6 1.18 0.72 0.44 0.01 0.1 L7 0.44 0.27 L8 0.1 0.164 MANUFACTURER DECLARES L9 0.164 0.037 0.061 L10 0.061 0.023 PRODUCT TESTED TO 0.023 0.0139 0.0085 European Standards EN 166: 2001 EN 166 Markings Lens / Frame / Glasses Goggles Visors AF N Personal Eye Visor Holder   Protection MANUFACTURER SYMBOL - AF = Anti-Fog     treatment European Standard, PW: Portwest (corresponds applying to all types of OPTICAL CLASS    to N - when the individual protection of the 1: Permanent wear (distortion free)   treatment is eye which protects from 2: Occasional wear   certified by the hazards likely to damage 3: Brief wear  notified body the eye, except for nuclear MECHANICAL RESISTANCE  and marked on radiation, x-rays, laser S: Minimal impact resistance (5,1 m/sec)   the lens). emissions and infrared F: Low energy impact (45 m/sec)  emitted by low-temperature B: Medium energy impact (120 m/sec)  AS K sources. Does not apply A: High energy impact (190 m/sec)  to eye protection for T: Impact test at extreme temperature (-5°C/+55°C) OPTIONAL - AS = Anti- which separate standards CHEMICAL RISKS (OPTIONAL)  Scratch exist (e.g. anti-laser eye 3: Resistance to liquid droplets  treatment protection, sunglasses for 3: Resistance to liquid splashes (corresponds general use). 4: Resistance to large dust particles (with > 5µm grain size)  to K - when the 5: Resistance to gases and fine dust particles (with < 5µm grain size) treatment is EN 170:2002 ELECTRICAL RISKS (OPTIONAL) certified by the European Standard notified body for Ultraviolet Filters and marked on the lens). Specifies the scale numbers and transmittance requirements for filters for protection against ultraviolet radiation. EN 172 European 8: Short circuit arc resistance  Standard for Sun glare THERMAL RISKS (OPTIONAL) filters for industrial use 9: Molten Metal splashes and hot solid projections    LENS TREATMENTS (OPTIONAL) Specification for Sun glare K: Resistance to surface damage by fine particles (anti-scratch treatment) Filters Used In Personal Eye- N: Resistance to fogging of oculars (anti-fog treatment) Protection For Industrial Use Comfort, Protection and Style 179

PS11 Tech Look Plus 300 AS AF ANSI 12 ANSI/ISEA Z87.1 .1 + (CLEAR) ANSI/ISEA Z87.1 .1 + U6 L3 (SMOKE) EN 166 1 FT EN 170 2C-1.2 (CLEAR) EN 172 5-3.1 (SMOKE) ∙ Dielectric safety glasses with metal free hinges featuring a tough and modern design with dual material on the side arms ∙ Wide elastic band ensuring an improved fit and makes it easily combined with hard hats and ear defenders ∙ Removable EVA foam gasket allows extra comfort and offers additional protection against shocks and dust Detachable foam back Polycarbonate, Nylon, EVA Foam Clear, Smoke PS12 ANSI Tech Look AS300 12 ANSI/ISEA Z87.1 .1 + (CLEAR) ANSI/ISEA Z87.1 .1 + U6 L3 (SMOKE) EN 166 1 FT EN 170 2C-1.2 (CLEAR) EN 172 5-3.1 (SMOKE) ∙ Innovative lightweight dielectric safety glasses with metal free hinges, featuring a tough and modern design with dual material on the side arms ∙ Side holes offer increased ventilation for optimum comfort MANUFACTURER DECLARES Polycarbonate, Nylon Clear, Smoke PRODUCT TESTED TO PW11 PW11 Levo Glasses with elastic band (included) Levo Glasses 300 AS AF ANSI 12 ANSI/ISEA Z87.1 + (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 F ∙ Light and comfortable glasses offering face sealing similar to a goggle ∙ Detachable foam offers additional protection against shocks and dust ∙ Back foam ventilation and lens treatment prevents misting and fogging of the ocular ∙ Dual use with classic arms or with wide elastic band Polycarbonate Clear, Smoke DETACHABLE FOAM offers additional protection against shocks and dust 180 Sport Inspired Designs with Advanced Protection

PW13 Clear View Glasses 300 AS AF ANSI 12 ANSI/ISEA Z87.1 + U6 (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 F EN 170 2C-1.2 (CLEAR) EN 172 5-3.1 (SMOKE) ∙ Tough looking wrap around glasses with streamline design MANUFACTURER DECLARES ∙ Excellent protective coverage and fitting PRODUCT TESTED TO ∙ Ultra light with a panoramic view ∙ Cord included Polycarbonate Clear, Smoke PW14 Lite Safety Glasses 300 AS AF ANSI 12 ANSI/ISEA Z87.1 + U6 (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 F EN 170 2C-1.2 (CLEAR) EN 172 5-3.1 (SMOKE) ∙ Super lightweight and durable glasses with a sleek design ∙ Larger fitting size for a perfect custom fit Polycarbonate MANUFACTURER DECLARES Clear, Smoke PRODUCT TESTED TO PW15 Fossa Glasses 300 AS ANSI 12 ANSI/ISEA Z87.1 + (CLEAR) ANSI/ISEA Z87.1 + U6 L1.7 (SMOKE) EN 166 1 F ∙ Wrap-around design glasses MANUFACTURER DECLARES ∙ One piece lens with integrated side protections PRODUCT TESTED TO ∙ Soft arm tips and rubber nose-bridge for ultra comfort ∙ Cord included Polycarbonate Clear, Smoke Dynamic High-Tech Safety Glasses 181

PW32 Wrap Around Glasses 300 AS ANSI 12 ANSI/ISEA Z87.1 + U6 (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 FT EN 170 2C-1.2 EN 172 5-3.1 (SMOKE) MANUFACTURER DECLARES ∙ Contour wrap-around design glasses PRODUCT TESTED TO ∙ One piece curved lens with molded nose ∙ Ultra lightweight for long uses MANUFACTURER DECLARES ∙ Flexible arms for ultra comfort PRODUCT TESTED TO ∙ Cord included Polycarbonate Clear lens/Black temple, Smoke lens/Black temple PW33 Classic Safety Glasses 300 AS ANSI 12 ANSI/ISEA Z87.1 + (CLEAR) ANSI/ISEA Z87.1 + S (SMOKE) EN 166 1 F EN 170 2C-1.2 EN 172 5-3.1 (SMOKE) COLOR ∙ Single panoramic lens glasses ∙ Molded side shield and browguard for optimized protection against impacts ∙ Adjustable arms for better fit ∙ Cord included Polycarbonate Clear lens/Black temple, Smoke lens/Black temple, Amber lens/Black temple PW34 Profile Safety Glasses 300 AS ANSI 12 ANSI/ISEA Z87.1 + (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 F COLOR ∙ Frameless glasses ∙ One piece curved lens with molded nose ∙ Molded browguard protection ∙ Excellent side protection ∙ Cord included Polycarbonate Clear lens/Black temple, Smoke lens/Black temple, Amber lens/Black temple 182 Total Protection from High Speed Particles

PS32 Wrap Around Plus Glasses 300 AS AF ANSI 12 ANSI/ISEA Z87.1 +U6 EN 166 1FT EN 170 2C-1.2 ∙ Our best selling Wrap Around Glasses is now available with additional edge protection, thanks to the removable gasket ∙ Offers a super comfortable fit and optimal protection against dust and impacts ∙ Lens are treated with anti-scratch and anti-fog coating for improved performance Polycarbonate Detachable foam back Clear PW38 Pan View Glasses 300 AS AF ANSI 12 ANSI/ISEA Z87.1 + (CLEAR) ANSI/ISEA Z87.1 + U6 L3 (SMOKE) EN 166 1 F ∙ Wrap-around design glasses MANUFACTURER DECLARES ∙ One piece curved lens with molded nose-bridge PRODUCT TESTED TO ∙ Ultra lightweight for long uses ∙ Soft rubber arms tips for extra comfort ∙ Cord included Polycarbonate Clear lens/Black temple, Smoke lens/ Black temple PW21 Indirect Vent Goggle 200 ANSI 20 ANSI/ISEA Z87.1.1 EN 166 1 B 3 ∙ Designed to be worn in a tough work environment ∙ Flexible PVC frame for ultra comfort ∙ Transparent color for better side visibility ∙ Indirect ventilation Polycarbonate Clear PW20 Direct Vent Goggle 200 ANSI 20 ANSI/ISEA Z87.1 + EN 166 1 B ∙ Designed to be worn in a tough work environment ∙ Flexible PVC frame for ultra comfort ∙ Direct Ventilation Polycarbonate Clear Always Putting Safety First 183

Hearing Protection Range USA Standards European Standards ANSI (US American National Standards Institute) EN 352-1: 2002 Hearing Protectors - Ear Muffs S3.19 - 1974 EN 352-2: 2002 Hearing Protectors - Ear Plugs EN 352-3: 2002 Hearing Protectors - Hard Hat Mounted Ear Muffs This standard specifies the test method for determining the level EN 352-4: 2002 Hearing Protectors - Level Dependent Ear Muffs of noise attenuation (NRR Noise Reduction Rating) of the hearing EN 352-8: 2002 Earmuffs with Entertainment Radio protection, as recommended by the EPA (U.S. Environmental All these standards establish requirements with regards to the Protection Agency) and in accordance with the Occupational manufacture, design, performances and test methods. Safety \& Health Administration(OSHA). SNR (Simplified Noise Reduction): Single average value of attenuation. Noise Reduction Rating (NRR) HML : Attenuation values expressed in terms of average levels of frequencies. H : Attenuation of PPE at high frequencies (pitched noises). This is a unit of measurement used to determine the effectiveness M : Attenuation of PPE at medium frequencies. of hearing protection devices to decrease sound exposure within L : Attenuation of PPE at low frequencies (bass sounds). a given working environment. Classified by their potential to reduce noise in decibels (dB). OSHA’S Permissible Noise Exposures Excessive noise is generally defined as exposure to 85 or more Duration per day, hours Sound level dBA slow response decibels of sound over an 8 hour period. According to OSHA, hearing protection is required for all employees at this degree of 8 90 exposure. In all cases where the sound levels exceed the values 6 92 shown below, a continuing, effective hearing conservation 4 95 program should be implemented. Example: if a worker is 2 100 exposed to 100dB in a 2 hour period, he is also required to wear 1 105 hearing protection. 0.5 110 <0.25 115 MANUFACTURER DECLARES Minimum requirements for the protection of workers against the PRODUCT TESTED TO risks related to noise exposure PW40 8 hours exposure time at 8 hours exposure time 8 hours exposure time 185 or above 85dB at or above 80dB between 75 dB and 80 dB Obligatory hearing Hearing protectors Hearing protection protection available to the worker recommended Requirements Directive 2003/10/EC: The performance of the hearing protector (its attenuation level) must be adapted to the risk assessment of the workplace. It should bring the noise level to a level that is not harmful to health, while avoiding over-protection which would cut the operator from his environment (warnings, communication, etc). 184 Ultimate Protection against Harmful Noise

PW41 NRR PW40 NRR PW43 NRR 25dB 22dB 26dB Super Ear Protector Classic Ear Protector Comfort Ear Protector 60 ANSI 60 ANSI 40 ANSI 10 10 10 ANSI S3.19 NRR 25dB ANSI S3.19 NRR 22dB ANSI S3.19 26dB EN 352-1 EN 352-1 EN 352-1 ∙ Ultra light and compact ear muff ∙ Classic design ear muff ∙ Comfort and robust ear muff ∙ Folds to palm size for better carriage and to keep ∙ Light and robust ∙ Lightweight for all day wear ∙ Ideal for all day use ∙ Pivoting pin cups for better fit clean ∙ Excellent attenuation rate ∙ Padded headband for comfort ∙ Ideal for all day wear but also for intermittent use ∙ High attenuation rate ∙ Adjustable dual pin system provides multiple ABS, Polystyrene Red ABS, Polystyrene positioning for better fit Black ∙ Excellent attenuation rate ABS, HIPS (High Impact Polystyrene) Red NRR PW47 NRR NRR PS41 25dB 24dB PS47 24dB Super HV Ear Protector Endurance Clip-On Endurance HV Ear Protector Ear Protector 60 ANSI 60 ANSI 60 ANSI 10 10 10 ANSI S3.19 NRR 25DB ANSI S3.19 NRR 24DB ANSI S3.19 NRR 24DB EN 352-1 EN 352-3 EN 352-3 ∙ Hi-Visibility color for increased visibility ∙ Hard hat mounting ear muff ∙ Hi-Vis color for increased visibility ∙ Adjustable dual pin system provides multiple ∙ Can be adjusted into the stand off position ∙ Hard hat mounting ear muff ∙ Can be adjusted into the stand off position when positioning for better fit when not in use ∙ Folds to palm size preventing external ∙ Easy to clip-on not in use ∙ Compatible with PS55, PW98, PS53, PV60, ∙ Easy to clip-on contamination ∙ Compatible with PS55, PW98, PS53, PV60, PV64, PV64, PV50, PV54, PS50 hard hats ∙ Excellent attenuation rate PV50, PV54, PS50 hard hats ∙ Excellent attenuation rate ∙ Excellent attenuation rate HIPS (High Impact Polystyrene), Stainless Steel ABS, Polystyrene ABS, Polystyrene 185 Hi-Vis Yellow Red Hi-Vis Yellow

EP08 EP02 Corded PU Foam Ear Plug PU Foam Ear Plug (200 pairs) X10 1 ANSI X10 2 ANSI 200 200 ANSI S3.19 NRR 32dB ANSI S3.19 NRR 32dB EN 352-2 EN 352-2 ∙ Disposable ear plugs made from soft ∙ Disposable ear plugs made from soft PU foam PU foam ∙ Corded for safe keeping ∙ Corded for safe keeping ∙ Each pair inside individual hygienic ∙ Each pair inside individual hygienic polybag polybag ∙ Excellent attenuation rate ∙ Excellent attenuation rate PU Foam NRR PU Foam NRR Orange Orange 32dB 32dB Easily adapts to ear canal and rapidly expands TO OFFER IMMEDIATE PROTECTION AGAINST HARMFUL NOISES EP20 Ear Plug Dispenser X4 2 ANSI 500 ANSI S3.19 NRR 32DB EP21 EN 352-2 Ear Plug Dispenser Refill Pack ∙ Dispenser container containing 500 pairs X8 2 ANSI of EP02 ear plugs 500 ∙ Soft ear plugs seal the ear canal with soft, ANSI S3.19 NRR 32DB slow recovery foam EN 352-2 ∙ Excellent noise reduction and comfort ∙ Soft ear plugs seal the ear canal with soft, slow-recovery foam ∙ Excellent noise reduction and comfort ∙ One gentle turn delivers a pair of ∙ Contains 500 pairs of EP02 ear plugs (refill for EP20 dispenser) uncorded foam earplugs ∙ Can be used on a horizontal surface or be hung on the wall PU Foam NRR PU Foam NRR Black Orange 32dB 32dB Contains 500 Pairs 186 Easily Adjusted inside the Ear Canal

Offering a versatile selection of lighting that provides excellent performance for an extensive array of tasks and duties. •Head Lights •Inspection Flashlights •Flashlights Lights Range LM RoHS - Restriction of Hazardous Substances Brightness Run time The ‘Restriction of Hazardous Substances’ directive is Brightness is measured in Lumens (LM). Run time means the amount of time you put in place to ensure all components of our electrical This icon denotes how many Lumens can expect to get from your light from fully products will not endanger the user. All our lights are each light can produce allowing you to powered to empty. This allows you to choose tested to this standard with compliance. pick the right light for the right job. the right ratio of brightness to run time to suit you best. PA66 2x1 Revolutionary Open LM 200 LM 2HRS Collapsible Portwest Ultra Inspection Design Flashlight CE 36 ROHS ∙ Brightness: 200/65 Lumens ∙ Beam Distance: 15 yards (side light), 80 yards (top light) ∙ Run time: 2/4 Hours ∙ Batteries: Included AAA x 4 ∙ Function: Inspection flashlight ∙ Illuminates automatically once extended ∙ Powerful wide magnetic base ∙ Positioning and anti roll design Aluminum Closed LM 65 LM 4HRS Red L 12.9” x D 1.7” PA65 Portwest Inspection LM 150 LM 4HRS Flashlight CE 120 ROHS 20 ∙ Brightness: 150/40 Lumens LM 40 LM 10HRS ∙ Beam Distance: 10 yards (side light), 20 yards (top light) ∙ Run time: 4/10 Hours 187 ∙ Batteries: Included AAA x 3 ∙ Function: Inspection flashlight ∙ Magnetic base, rubberized body for grip with clip for hands free inspection ∙ Compact but extremely powerful and useful lighting ABS Black L 6.5” x D 1”

Impact PA61 resistant Portwest High Powered Enforcer CE 24 ROHS ∙ Brightness: 800 Lumens ∙ Beam Distance: 550 yards Max ∙ Run time: 40 Hours ∙ Batteries: Included D x 3 ∙ Function: High-Medium-Low-Flash-SOS ∙ Impact and water resistant ∙ The ultimate in security flashlights LM 800 LM 40HRS Aluminum Black L 12.4” x D 2” PA54 Portwest Tactical Flashlight CE 72 ROHS 6 BELT CLIP ∙ Brightness: 180 Lumens ∙ Beam Distance: 330 yards Max WRIST ∙ Run time: 8 Hours STRAP ∙ Batteries: Included AAA x 3 ∙ Function: High-Medium-Low-Flash 8HRS ∙ Compact and comes with a useful belt clip and wrist strap LM 180 LM Aluminum Black L 5.4” x D 1.4” INSPECTION PA62 FUNCTION 19 LED Utility Flashlight WALL MOUNTABLE CE 24 ROHS SPOTLIGHT FUNCTION ∙ Brightness: 74 Lumens ∙ Beam Distance: 15 yards ∙ Run time: 8 Hours ∙ Batteries: Included D x 4 ∙ Multi-function, can be used as a flashlight, inspection light and spot light ∙ Wall mountable for easy access in emergencies ABS Yellow/Black L 6.1” x W 4.6” x H 7.1” LM 74 LM 8HRS PA60 WATER 7 LED Rubber Flashlight resistant CE 48 ROHS LM 31 LM 8HRS ∙ Brightness: 31 Lumens ∙ Beam Distance: 55 yards ∙ Run time: 8 Hours ∙ Batteries: Included D x 2 ∙ Rubberized for grip and durability ∙ A classic ergonomically design utilizing modern LED technology Rubber, ABS Yellow/Black L 7.7” x D 3” 188 Next Generation Lighting in the USA

Brightness LM 500 LM 2HRS PA64 500 LUMENS Portwest Ultra Power Head Light 48 6 CE ROHS ∙ Brightness: 500 Lumens ∙ Beam Distance: 165 yards (high), 90 yards (medium), 45 yards (low) ∙ Run time: 2 hours ∙ Batteries: Included AA x 4 ∙ Function: High-Medium-Low-Flash-SOS ∙ Tilt control for different working positions ∙ Rubberized headband stitching for a better fit ∙ Easy to load and durable battery pack ∙ Button protector to avoid accidental switching on when not in use Aluminum, ABS, Polyester Yellow/Black, Adjustable PA63 Portwest Dual Power Head Light 96 12 CE Lightweight ROHS ∙ Brightness: 100 Lumens ∙ Beam Distance: 10 yards (high), 5 yards (medium) ∙ Run time: 8 Hours ∙ Batteries: Included AAA x 3 ∙ Function: High-Medium-Flash ∙ Bright, compact and lightweight ∙ Tilt control for different working positions ∙ Tough rubberized coating ABS, Polyester LM 100 LM 8HRS Yellow/Black, Adjustable PA50 LM 40 LM 10HRS LED Head Light 120 20 CE ROHS ∙ Brightness: 40 Lumens ∙ Beam Distance: 15 yards (high), 10 yards (medium) ∙ Run time: 10 Hours ∙ Batteries: Included AAA x 3 ∙ Function: High-Medium-Flash ∙ 8 LED ∙ Tilt control for different working positions ABS Silver/Black, Adjustable Advanced Lighting Innovation 189

B029 Beanie LED Head Light USB Rechargeable 9144 12 CE ROHS ∙ Warm and comfortable acrylic beanie ∙ Rechargeable LED can be charged in a USB Port ∙ Brightness: 150 Lumens ∙ Run time: 4 hours ∙ Power: USB Charge ∙ Function: High-Medium-Flash ∙ Beam Distance: 10 yards (High), 5 yards (Medium) 100% Acrylic, Knit Black, Yellow, One Size NEXT GENERATION LIGHTING ON / OFFHigh-Visibility Yellow HV05 Silver ON / OFF Illuminated Flashing Armband PW80 600 Support Belt 25 48 EN 13356 12 CE ROHS ∙ Provides support to the lower back and abdomen ∙ Adjustable elastic straps for a secure fit ∙ Bright illuminated reflective panel ∙ 8” wide belt ∙ 2 light settings: constant and pulse ∙ Adjustable waistbelt and shoulder straps ∙ Compact and lightweight ∙ Elasticated for a secure and comfortable fit ∙ Battery life of 80 hours ∙ Can be worn underneath or over clothing ∙ CR2032 3v battery included ∙ Machine washable ∙ CE Certified 38% Latex, 62% Polyester ABS, LED, TPU Black Hi-Vis Yellow, Silver One Size S-XL PA99 Slimline 120dB Safety Whistle X60 20 ∙ Slimline whistle can create an ear-piercing 120dB ∙ Ability to signal for help from vast distances ∙ Lightweight and portable ∙ Cord included Plastic Orange 2.24” x 0.9” 120dB 190 Essential High Quality PPE Accessories

Luggage Range A collection of versatile luggage pieces, suitable for traveling or general everyday use. Robustly constructed with strong materials and tough components. Reliability and durability guarantee 100% customer satisfaction. B900 65 Holdall Bag LITERS 12 ∙ Ideal for carrying tools and equipment, or as a travel bag ∙ Adjustable shoulder strap for added comfort ∙ 2 zipper compartments ∙ ID card holder for ID card display ∙ Robust base panel 100% Polyester, PVC Coated, 15oz Black, Navy Capacity 65 Liters L27” x W10” x H15.5” B904 25 Quick Release Hi-Vis Rucksack LITERS 24 ∙ Hardwearing 600D fabric ∙ Padded straps and back panel for comfort ∙ Multiple storage pockets ∙ Cell phone pocket ∙ Innovative quick release anti-entanglement system ∙ Fabric and reflective tape meet the requirements of ANSI/ISEA 107-2015 and EN ISO 20471 100% Polyester 600D Fabric, 7.5oz 25 210T PA, 3oz Orange LITERS Capacity 25 Liters L11” x W8.5” x H17” B905 Hi-Vis Rucksack 24 ∙ Hard wearing 600D fabric ∙ Padded straps and back panel for comfort ∙ Multiple storage pockets ∙ Cell phone pocket ∙ Fabric and reflective tape meet the requirements of ANSI/ISEA 107-2015 and EN ISO 20471 100% Polyester 600D Fabric, 7.5oz 210T PA, 3oz Orange, Yellow Capacity 25 Liters L11” x W8.5” x H17” Industries Best Selling Luggage Range 191

Kneepads KP05 Range Kneeling Pad Portwest knee pads offer a range 84 of knee protection to suit every 28 situation. ∙ Lightweight EVA foam cushioning Type 1 (strap on knee pads) ∙ Reduces knee and back strain ∙ Integral carry handle Type 2 (insert knee pads) EVA Foam Type 3 (kneeling pads) Black One Size All Portwest knee pads use L15.5” x W7.5” x H1” premium high density material to give the user the best protection S156 possible for their knees no matter Portwest Knee Pad the hazard. Diverse materials such as EVA foam, neoprene rubber and 96 silicone gel inserts are used to 24 ensure maximum wearer comfort. EN 14404:2004+A1:2010 TYPE 2 LEVEL 0 Ergonomics is a key feature in our ∙ Ergonomically designed to hug knee pads design and is backed up your knee in the positive feedback we receive ∙ Durable high density EVA protects from our wearer trials. and gives comfort to the wearer ∙ Fits all Portwest knee pad pockets EN 14404:2004+A1:2010 EVA Foam This European Standard specifies Black 8.5” x 6.5” the requirements for knee protectors type 1 and type 2. KP10 Type 1 being strap knee pads and High Density Knee type 2 being inserts. The level of Pad protection it offers ranges from a level 0 to a level 2. Level 2 offers 72 the greatest protection. 18 Superior ∙ High density polyurethane both Comfort and protects and cushions the wearer’s Protection knee ∙ Ribbed design for stability ∙ Waterproof and easily cleaned Polyurethane Black Adjustable 192 Ultimate Protection For Your Knees

STRAP ON KNEE PADS KP40 Ultimate Gel Knee Pad 36 EN 14404:2004+A1:2010 TYPE 1 LEVEL 1 ∙ Designed to give stability to the wearer by virtue of its flexible and wide foot print ∙ Unrivaled comfort is provided by silicone gel inserts ∙ Ergonomically designed and tested straps ensure no pinching to the back of the wearers leg ∙ A strong and durable outer shell makes for a long lasting tough knee pad PVC Shell, Nylon, EVA Foam, Neoprene Black/Turquoise Adjustable Greater Stability KP30 Super Gel Knee Pad 36 EN 14404:2004+A1:2010 TYPE 1 LEVEL 0 ∙ Strong outer shell offers protection and traction ∙ Silicone gel inserts protect joints and give great wearer comfort ∙ Ergonomically designed and tested straps ensure no pinching to the back of the wearers leg PVC Shell, Nylon, EVA Foam, Neoprene Black Adjustable Ergonomic Straps NO PINCH KP20 Lightweight Knee Pad 48 EN 14404:2004+A1:2010 TYPE 1 LEVEL 0 ∙ Lightweight wrap-around design ∙ Tough outer shell for protection ∙ Breathable inner fabric allows air to circulate ∙ A thick foam center cushions the wearers knee Nylon, EVA Foam, Plastic Black Adjustable Light weight Ergonomically Engineered Kneepads 193

Knives Range Portwest knives provide a full range of cutting solutions including replacement blades. Our knives offer razor sharp precision and are ergonomically designed for easier handling. Using only high quality materials, they are used across a wide variety of industries including factories, warehouses, trades men and D.I.Y. enthusiasts. You can trust our knives and blades to perform while making safety a priority. Always wear Automated TUV GS Product Service Certification. Complies and safety glasses blade retraction meets the requirements of the German Equipment Safety Law. Classic design KN10 Ultra Safety Cutter 144 ∙ Blade retracts once the user disengages the blade 12 slider button avoiding accidents KN90 ∙ Designed for right handed users ∙ Classic safety knife design Zinc Alloy Black Durable metal frame KN20 Pro Safety Cutter 144 12 TUV GS KN90 ∙ Tough design with rubber grip for improved safety ∙ Blade retracts once the user disengages the blade slider button avoiding accidents ∙ Suitable for both right and left handed users Zinc Alloy, Rubber Silver 194 Your One Stop Shop For Knives

KN40 Includes 10 spare blades Retractable Safety Cutter Ergonomic TUV GS 72 handle design 12 ∙ Auto retractable blade, which disengages when Changes blades it loses contact with the cutting surface KN91 in seconds ∙ Quick blade change system ∙ Designed for heavy everyday use ∙ Accommodates use with a lanyard Zinc Alloy, Rubber Blue KN30 Portwest Folding Utility Knife ∙ Foldable aluminum knife for easy storage 96 ∙ Quick blade change system 8 ∙ One handed opening for working at height ∙ Rubber handle for better grip KN91 ∙ Useful metal belt clip ∙ Includes 5 blade replacements Aluminum, Rubber Blue KN18 144 12 Portwest Snap Off Knife ∙ Ergonomically designed for a stronger grip, quick blade adjustment ∙ Includes 3 blade replacements which are stored in the knife ∙ Rust resistant stainless steel blade holder ABS, Rubber KN93 Blue KN93 KN91 Portwest Snap Off KN90 Replacement Blades for KN18 Replacement KN30 and KN40 Cutters Blades (10) Replacement Blades for (10) KN10 and KN20 (10) ∙ Replacement blades for KN18 ∙ 8 cutting edges X12 ∙ Replacement blades for KN10 and X20 ∙ Replacement blades for KN30 X20 ∙ 10 blades per pack X20 KN20 X25 and KN40 X25 ∙ Generic size 18mm snap off 10 10 10 ∙ 2 cutting edges ∙ 2 cutting edges blade fits most other designs ∙ 10 blades per pack ∙ 10 blades per pack Carbon Steel Silver ∙ Unparalleled sharpness and ∙ Unparalleled sharpness and superior edge retention superior edge retention Carbon Steel Carbon Steel Silver Silver Engineered With Safety In Mind 195

NEW MERCHANDISING Z600 Z613 CUSTOMIZE YOUR OWN Z612 Z622 STAND As well as a comprehensive range of clothing, footwear, PPE and accessories, Portwest can also supply an outstanding range of merchandising stands to promote products. Each stand is customized and has been specifically designed to show the items in the best possible way. A A - Denotes a fixture that is B B - Denotes a fixture that is Z601 compatible with the Z600 compatible with the Z601 Wall Bay Unit Free Standing Unit A+B A+B - Means the fixture Denotes if applying this on can be used with either Z600 you will need Z612 as a the Z600 or the Z601 base. If applying this on Z601 you will need Z611 as a base. Z534 Z635 BZ601 Z6 AZ600 Large Freestanding Floor Stand L4ft 11” x Starter Wall Bay W3ft W1ft 7.5” x H4ft 8” 11” x H7ft 10.5” 1 1 Z613 Z636 Z610 12 Z611 Z612 Stepped Out Hanging Rail 3ft Large Shelf L47” x W15” Shallow RSB 19.5” Shallow RSB 3ft 11” 11” Stepped Out Hanging A3 Rail 19.5” B 32 A 12 A8 B Z620 Z621 Z630 Z635 Z622 Forward Hanging Arm 8.5” Forward Hanging Arm 13.5” Hook 8” Shoe Shelf L110” x W23” Stepped Arm 196 A+B 80 A+B 48 A+B 100 A+B 30 A+B 40

Z630 Z621 Z635 Z529 Z534 Z533 Hard Hat Stand Glove/PPE Display H86” x W21.5” Stand 1 H67” x L27.5” x W15.5” 1 Z636 611 Z587 Z541 Z543 Portwest Large Bin Footwear Cardboard Display 11 AUTHORIZED DISTRIBUTOR Z587 Z583 Z456 Z457 Portwest Mat Large PVC Banner Portwest Wooden Jacket Portwest Wooden L79.5” x W39” W82” x H32” Hanger Pants Hanger 3 1 100 50 Z586 Z529 Z580 Pull Up Glasses Display Portwest Paper Banners Stand Bag H17.5” x W6” x 6 D7” 200 197 MICRO P AKVIEW 1 Z586NCRB003 - 300D Industry High Visibility GLOBAL WORKTWR AEN AS LRU CSEPN ET CH IEAL MLEIST TS Z586NCRB010 - Iona Z586NCRB002 - Bizflame Z586NCRB001 - Biztex Z586NCRB011 - Peakview Z586NCRB007 - Footwear

INDEX STYLE PAGE STYLE PAGE STYLE PAGE STYLE PAGE STYLE PAGE 2886 105 A640 151 B900 191 FR43 23 HV55 80 A001 139 A641 146 B904 191 FR44 22 ID12 A100 153 A643 146 B905 191 FR75 26 KN10 176 A110 158 A645 146 BZ31 18 FR89 18 KN18 194 A111 158 A655 150 C470 77 FR94 15 KN20 195 A120 152 A665 149 C472 77 FR95 19 KN30 194 A140 145 A667 144 C701 105 FR96 19 KN40 195 A145 145 A688 150 C720 106 FT15 KN90 195 A146 145 A690 150 C813 107 FW05 123 KN91 195 A150 153 A691 150 C814 109 FW07 130 KN93 195 A198 157 A710 141 CS10 100 FW10 129 KP05 195 A199 157 A721 138 CS11 100 FW14 128 KP10 192 A210 159 A722 138 CS20 101 FW16 128 KP20 192 A220 160 A724 139 CS21 101 FW17 121 KP30 193 A225 160 A725 139 CV01 81 FW22 121 KP40 193 A230 159 A726 139 CV03 81 FW31 129 L470 193 A245 161 A729 138 CV04 81 FW33 126 L476 A251 162 A730 141 E041 61 FW34 125 LW70 71 A260 162 A740 141 E043 61 FW39 125 P200 71 A270 161 A745 140 EP02 186 FW57 126 P201 49 A271 161 A780 144 EP08 186 FW63 124 PA10 177 A300 154 A790 140 EP20 186 FW64 127 PA50 177 A301 154 A810 157 EP21 186 FW65 127 PA54 175 A310 156 A910 164 F124 104 FW69 119 PA58 189 A315 156 A925 164 F125 104 FW75 124 PA60 188 A320 156 AP02 143 F474 78 FW95 130 PA61 175 A330 154 AP31 147 F477 79 G465 131 PA62 188 A340 153 AP32 148 F813 107 G470 PA63 188 A350 155 AP52 148 FC21 122 G476 34 PA64 188 A351 155 AP62 143 FC60 123 GL13 35 PA65 189 A352 155 AP80 152 FC61 123 GL16 35 PA66 189 A500 163 B013 101 FC64 122 H441 101 PA91 187 A530 163 B023 101 FD10 120 H444 101 PA99 187 A620 147 B029 190 FD15 120 HA10 57 PS11 176 A621 149 B303 64 FR01 20 HA15 56 PS12 190 A622 147 B304 65 FR02 20 HA16 101 PS32 180 A625 148 B307 79 FR09 21 HB11 80 PS41 180 A630 151 B308 64 FR41 23 HV05 80 PS47 183 80 185 190 185 198