DURA-BLOK Supports

DBE Series

Support Base with Rod Risers & Channel

• Base with (2) 1/2” electro zinc all threaded rod risers - Top channel is 1” (25.4mm) tall.

See chart for adjustable height x wide x length.

• 100% recycled rubber, UV resistant.

• Load Rating* 200 lbs. (0.89kN) (To increase load capacity use load distribution plate

CLDP10)

• DURA-BLOK™ DBE-Series channel support is designed as a superior support of piping

systems, cable tray, HVAC equipment and many other applications where elevation

adjustment is critical. The DURA-BLOK is UV resistant and suitable for installation on

any type of roofing material or other flat surfaces. (For pipe straps/clamps, rollers

and roller supports that can be used with these DURA-BLOK supports, see page 202)

* General Note: Consult roofing manufacturer or engineer for roof load capacity.

The weakest point may be the insulation board beneath the rubber membrane.

DBR Series

Support Base with Rod Risers & Pipe Roll

• Base with (2) 1/2” electro zinc all threaded rod risers and a

B3114-31/2 pipe roll with sockets - base is 4” (101.6mm) high x 6” (152.4mm)

wide x 9.6” (243.8mm) long. Overall height is 12” (304.8mm) from bottom of

base to contact point on roller.

• Pipe roll & sockets for up to 31/2” (90) pipe sizes.

• 100% recycled rubber, UV resistant.

• Load Rating* 200 lbs. (0.89kN) (To increase load capacity use load distribution plate

CLDP10)

• DURA-BLOK DBR-Series support is designed to support pipe up to 31/2” (90) nominal

size where difference in elevation is required and longitudinal movement is

expected. The DURA-BLOK is UV resistant and approved for installation on any type

of roofing material or other flat surfaces.

Thickness x Width x Length Wt./Each

Part No. In. mm Lbs. kg

CLDP10 11 Ga. x 15/8” x 91/2” (3.0 x 41.3 x 241.3) 0.53 (0.24)

Adjustable Height x Width x Length Wt./Each

Part No. In. mm Lbs. kg

DBE10-8 51/2-8” x 6” x 9.6” (139.7-152.4 x 152.4 x 243.8) 5.68 (2.58)

DBE10-12 51/2-12” x 6” x 9.6” (139.7-304.8 x 152.4 x 243.8) 5.72 (2.59)

DBE10-16 51/2-16” x 6” x 9.6” (139.7-406.4 x 152.4 x 243.8) 5.76 (2.61)

CLDP10

Load Distribution Plate

• 11 ga. (3.0mm) steel plate with slots.

• Dimensions: 15/8” (41.3mm) wide x 91/2” (241.3mm) long.

• DURA-BLOK CLDP10 load bearing stabilizer plate increases load ratings

for DBE Series and DBR Series by allowing the load from the threaded

rods to be distributed over the length of the base instead of the point

load where the rods attach to the base.

Adjustable Height x Width x Length Wt./Each

Part No. In. mm Lbs. kg

DBR10-12 up to 12” x 6” x 9.6” (up to 304.8 x 152.4 x 243.8) 8.20 (3.72)

Loosen hex nuts

and slide plate

under the flat

washers

Retighten the hex

nuts with plate in

place

Reference page 196 for general fitting and standard finish specifications.

DURA-BLOK Rooftop Supports

199 B-Line series strut systems

DURA-BLOK Supports

DB__DS Series

Support Bases with B22SH

Vertical & Horizontal Channel Members

• Product is shipped unassembled.

• Two (2) DB20 bases with 1” (25.4mm) tall galvanized channel -

Bases are 5” (127.0mm) high x 6” (152.4mm) wide x 20.2” (513.1mm) long.

Vertical & Horizontal Riser Channels (SH Style) - 15/8” (41.3mm) x 15/8” (41.3mm) x 12 ga. (2.6mm)

Fittings & Hardware - Electro-Plated Steel

• 100% recycled rubber, UV resistant.

• Ultimate Load Rating: 1000 lbs. (4.45kN) (Uniform Load)*

• DURA-BLOK™ DB__DS-Series channel support with risers is designed for superior support of piping

systems, cable tray, HVAC equipment, walkway systems and many other applications. The DURA-BLOK

is UV resistant and suitable for installation on any type of roofing material or other flat surfaces.

(For pipe straps/clamps, rollers and roller supports that can be used with these DURA-BLOK supports,

see page 202)

* General Note: Consult roofing manufacturer or engineer for roof load capacity.

The weakest point may be the insulation board beneath the rubber membrane.

DB2318DS

DB2924DS

DB5336DS

Length Width (overall) (overall)

Height

(overall)

B

B + 4.5” (114mm)

A

Reference page 196 for general fitting and standard finish specifications.

DURA-BLOK Rooftop Supports

200 Eaton B-Line series strut systems

DURA-BLOK Supports

A = Adjustable height from bottom of DURA-BLOK™ to top of horizontal channel.

B = Space between fittings that support horizontal channel.

Height (overall) = Distance from bottom of DURA-BLOK to top of upright channel.

Width (overall) = Distance from outside-to-outside of DURA-BLOK supports.

Length (overall) = Distance from end-to-end of DURA-BLOK supports.

A Min. to Max. B

Part No. In. mm In. mm

DB2318DS 10.56” to 20.75” (268 to 527) 131/2” (343)

DB2918DS 10.56” to 26.75” (268 to 679) 131/2” (343)

DB4118DS 10.56” to 38.75” (268 to 984) 131/2” (343)

DB5318DS 10.56” to 50.75” (268 to 1289) 131/2” (343)

DB2324DS 10.56” to 20.75” (268 to 527) 191/2” (495)

DB2924DS 10.56” to 26.75” (268 to 679) 191/2” (495)

DB4124DS 10.56” to 38.75” (268 to 984) 191/2” (495)

DB5324DS 10.56” to 50.75” (268 to 1289) 191/2” (495)

DB2336DS 10.56” to 20.75” (268 to 527) 311/2” (800)

DB2936DS 10.56” to 26.75” (268 to 679) 311/2” (800)

DB4136DS 10.56” to 38.75” (268 to 984) 311/2” (800)

DB5336DS 10.56” to 50.75” (268 to 1289) 311/2” (800)

DB2348DS 10.56” to 20.75” (268 to 527) 431/2” (1105)

DB2948DS 10.56” to 26.75” (268 to 679) 431/2” (1105)

DB4148DS 10.56” to 38.75” (268 to 984) 431/2” (1105)

DB5348DS 10.56” to 50.75” (268 to 1289) 431/2” (1105)

Height (overall) Width (overall) Length (overall) Wt./Each

Part No. In. mm In. mm In. mm lbs. kg

DB2318DS 23” (584) 255/8” (651) 20.2” (513) 33.31 (15.11)

DB2918DS 29” (736) 255/8” (651) 20.2” (513) 35.00 (15.88)

DB4118DS 41” (1041) 255/8” (651) 20.2” (513) 38.40 (17.42)

DB5318DS 53” (1346) 255/8” (651) 20.2” (513) 41.80 (18.96)

DB2324DS 23” (584) 315/8” (803) 20.2” (513) 34.15 (15.49)

DB2924DS 29” (736) 315/8” (803) 20.2” (513) 35.84 (16.26)

DB4124DS 41” (1041) 315/8” (803) 20.2” (513) 39.25 (17.80)

DB5324DS 53” (1346) 315/8” (803) 20.2” (513) 42.65 (19.34)

DB2336DS 23” (584) 435/8” (1108) 20.2” (513) 35.84 (16.26)

DB2936DS 29” (736) 435/8” (1108) 20.2” (513) 37.56 (17.03)

DB4136DS 41” (1041) 435/8” (1108) 20.2” (513) 40.95 (18.57)

DB5336DS 53” (1346) 435/8” (1108) 20.2” (513) 44.34 (20.11)

DB2348DS 23” (584) 555/8” (1415) 20.2” (513) 37.55 (17.03)

DB2948DS 29” (736) 555/8” (1415) 20.2” (513) 39.25 (17.80)

DB4148DS 41” (1041) 555/8” (1415) 20.2” (513) 42.65 (19.34)

DB5348DS 53” (1346) 555/8” (1415) 20.2” (513) 46.03 (20.88)

DB__DS Series cont.

Reference page 196 for general fitting and standard finish specifications.

DURA-BLOK Rooftop Supports

201 B-Line series strut systems

DURA-BLOK Supports

Above rollers can be mounted on DB Series, DB6 Series, and DB10 Series units.

B3126 Series

B-LINE

BVP150

1 1/2” I.P 1 1/2” I.P .

BVT Series

B2400

Series

B218

B101

BTS

B22SH

B634

TN Nuts B22TH

HHCS

B104

B379 B219 Series B479

B2000 Series

Compatible Components Available to make DURA-BLOK bases more versatile

B3124

Series

DBR Series

Support Bases with Channel & Pipe Roller

• Base with 1” (25.4mm) tall galvanized channel -

see chart for overall height, width and length.

• 100% recycled rubber, UV resistant.

• Load Rating: (See Chart Below)*

• DURA-BLOK™ DBR-Series support is designed to support pipe where

longitudinal movement is expected. The DURA-BLOK is UV resistant

and approved for installation on any type of roofing material or other flat

surfaces.

Roller Block & Channel -Height x Width x Length Height** Wt./Each Load Rating

Part No. Part No.† In. mm In. mm Lbs. kg Lbs. kN

DBR2-31/2 B3126-2 to 31/2 5” x 6” x 9.6” (127.0 x 152.4 x 243.8) 7.09” (180) 5.28 (2.39) 500 (2.22)

DBR4-6 B3126-4 to 6 5” x 6” x 9.6” (127.0 x 152.4 x 243.8) 7.09” (180) 10.63 (4.82) 500 (2.22)

DBR8-10 B3126-8-10 5” x 6” x 20.2” (127.0 x 152.4 x 513.1) 8.34” (212) 15.99 (7.25) 1000 (4.45)

DBR12-14 B3126-12-14 5” x 6” x 20.2” (127.0 x 152.4 x 513.1) 9.38” (238) 21.34 (9.68) 1000 (4.45)

DBR16-20 B3126-16-20 5” x 6” x 20.2” (127.0 x 152.4 x 513.1) 9.78” (248) 26.70 (12.11) 1000 (4.45)

† See Pipe Hanger Catalog for dimensions and specifications. ** From bottom of rubber block to bottom of pipe/tubing.

DBR4-6

DBR16-20

Reference page 196 for general fitting and standard finish specifications.

DURA-BLOK Rooftop Supports

202 Eaton B-Line series strut systems

DURA-BLOK Supports

Rooftop Applications

DURA-BLOK Rooftop Supports

203 B-Line series strut systems

DURA-BLOK Supports

DURA-BLOK Rooftop Supports

204 Eaton B-Line series strut systems

GRATEWALK™

Rooftop Walkway with Integrated DURA-BLOK™ Supports

Features & Benefits of the GRATEWALK Rooftop Walkway

• Available with slip resistant GRATE-LOCK™, helping provide a safe walkway for foot traffic on the roof.

• Easy to install, elevated design, creates an identifiable path for foot traffic helping prevent wear and tear to

the roof surface.

• The cross-over design offers safe passage over existing cabling, piping, cable tray or any other

interference on the rooftop.

• The self cleaning pattern allows water and dirt to easily flow through, helping make the grating

an ideal walkway in all weather conditions.

• Handrail options are available

• Integrated with 100% post-consumer recycled rubber supporting LEED credit qualification.

• Provide solid support for the walkway that stays in place and replaces the need for separate rubber

roof mounting pads which tend to float away.

B-Line series GRATEWALK™ Rooftop Walkways with DURA-BLOK™ supports provide the optimal solution to

extend the life of your roof, while providing a safe pathway to roof mounted support equipment.

DURA-BLOK Supports

DURA-BLOK Rooftop Supports

205 B-Line series strut systems

GRATEWALK™

Rooftop Walkway with Integrated DURA-BLOK™ Supports

The GRATEWALK™ Rooftop Walkway with Integrated

DURA-BLOK™ Supports* is available in a variety of configurations.

• Straight sections for long straight stretches of pathway

• Cross-over options to install over the existing cable trays,

piping, and more

• Stairways over the top of existing equipment or leading

up to existing equipment

• Handrail options available for additional wallway safety

and support

• Platforms to provide access to rooftop mounted equipment

• Accessories available to support unique requirements

* All Items are shipped individually for field assembly.

Engineering Design Service

Figure A

• Take-off and estimating

• Specification review and development

• Alternative layout designs

• Technical consultation

• Submittal drawing packages (see Figure A)

including assembly instructions

A complete system of top quality, time saving products, designed for surface metal raceways, lighting and cable

supports. Innovative designs offer many installation advantages. The surface raceways are U.L. listed and meet

the requirements of the National Electrical Code, Article 384.

Surface Raceways

Our channel provides structural support in addition to a raceway system.

For U.L. wire fill see chart on page 278-279.

Cable Supports

A full range of clamps and saddles are offered in porcelain and thermoplastic elastomer. Our Insulclamp™ cable

clamps and porcelain saddles are furnished complete with steel clamps (electro-plated) and Everdur hardware

where required.

Materials & Finishes*

Steel products are made from low carbon steel strips

or plates. Porcelain saddles and clamps are made by

dry process and white glazed (porcelain dielectric

strength is 50 volts per mil).

*Unless otherwise noted.

Design Load

Design load data published includes a Safety Factor of 3.0 (Safety Factor = Ratio of ultimate load to the design

load).

U.L. listed raceway channels:

B11, B11KO6 B32, B32KO6

B12, B12KO6 B42, B42KO6

B22, B22KO6 B52, B52KO6

B24, B24KO6 B54, B54KO6

B26, B26KO6 B56, B56KO6

U.L. File No. E29637

In all cases, the snap-in closure strip is required to complete raceway enclosure.

Metric Electrical Accessories

Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.

Finish

Code Finish Specification

PLN Plain ASTM A1011

33,000 PSI min. yield

ZN Electro-Plated Zinc ASTM B633 SC3 Type III

GRN DURA GREEN™

GALV Pre-Galvanized ASTM A653

YZN Yellow Zinc Chromate ASTM B633 SC3 Type II

Electrical Accessories

206 Eaton B-Line series strut systems

Channel Depth Channel Channel Fixture Connection Internal Internal

Number in. mm Hanger Hanger Hanger End Cap End Cap Straight Splice Tee Splice

B22A 31

/4” (82.5) B616-22A* B241S* B616S-22A* B205 or B285 B392-22** B766-22 (2) B768-22 (2)

B285

B11 31/4” (82.5) B616-22A* B241S* B616S-22A* B222 B392-11** B766-11 B768-11

B12 27/16” (61.9) B616-22A* B241S* B616S-22A* B221 B392-12** B766-12 B768-12

B22 15/8” (41.3) B616* B216S* B616S* B205 or B285 B392-22** B766-22 B768-22

B24 B616TG* B223 or B286

B26 15/8” (41.3) B616* –– – B392-22** – –

B32 13/8” (34.9) B616* B216S* B616S* B206 B392-32** B766-32 B768-32

B616TG*

B42 1” (25.4) B616* B215S* B616S* B203 – B766-42 B768-42

B616TG*

B52 13/16” (20.6) B616* B215S* B616S* B220 or B283 – B766-52 B768-52

B54 B616TG* B204 or B284

B56 13/16” (20.6) B616* B215S* B616S* – – B766-56 – B616TG*

1 1A 2 3 3A 4 5

*Specify Hanger Rod or Conduit Size.

**Specify Conduit Size

Other Items Shown on Illustration

Selection Chart

Snap-in Closure Strip

H.I.D. Fixture Hanger Beam Clamp Conduit Connection Plate B718 Series Junction Box

Beam Clamp Beam Clamp Beam Clamp

B217-20 (6) (7) (8) (9)

B465 (10) (11) (12) (13)

B351L B755 B751

B447 B719

B447A

B750

(8)

(9)

(5)

(2)

(13)

(13)

(10)

(1)

(1) (4)

(7) (11)

(1) or

(1A) (Not Shown)

(3) or

(3A) (Not Shown)

(6)

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Electrical Accessories

207 B-Line series strut systems Eaton

B616-7/8

Channel Hanger

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 25 Lbs. (11.3 kg)

B616-9/16

Channel Hanger

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

whenused as a fixture support

• Includes:

2 pcs. 3/8” Flat washers for

use with 3/8” ATR

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 25 Lbs. (11.3 kg)

B616S-9/16

Fluorescent Fixture Hanger with Stud

• Design Load 150 Lbs. (.67 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Allows more than 1/2” (12.7) space

between channel and fixture

• Includes:

2 pcs. 3/8” Flat washers

for use with 3/8” ATR

• Material:16 gauge (1.5)

• Standard finish: ZN

• Wt./C 30 Lbs. (13.6 kg)

B616S-7/8

Fluorescent Fixture Hanger with Stud

• Design Load 150 Lbs. (.67 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Allows more than 1/2” (12.7) space

between channel and fixture

• Standard finish: ZN

• Material:16 gauge (1.5)

• Wt./C 30 Lbs. (13.6 kg)

B616-22A-9/16

Channel Hanger

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Includes:

2 pcs. 3/8” Flat washers for use with 3/8” ATR

• Material: 14 gauge (1.9)

• Standard finish: ZN

• Wt./C 44 Lbs. (19.9 kg)

B616-22A-7/8

Channel Hanger

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Material: 14 gauge (1.9)

• Standard finish: ZN

• Wt./C 44 Lbs. (19.9 kg)

31/8”

(79.4)

11/2”

(38.1)

9/16” (14.3) Dia. For

1/2” ATR

7/8” (22.2) Dia. For

1/2” (15) Conduit

31/8”

(79.4)

11/2”

(38.1)

31/8”

(79.4)

11/2”

(38.1)

31/8”

(79.4)

11/2”

(38.1)

51/8”

(130.2)

11/2”

(38.1)

9/16” (14.3) Dia. For

1/2” ATR

7/8” (22.2) Dia. For

1/2” (15) Conduit 11/2”

(38.1)

51/8”

(130.2) Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Fluorescent Fixture Hangers

208 Eaton B-Line series strut systems

B616S-22A-7/8

Fluoreescent Fixture Hanger with Stud

• Design Load 150 Lbs. (.67 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Allows more than 1/2” (12.7) space

between channel and fixture

• Material: 14 gauge (1.9)

• Standard finish: ZN

• Wt./C 49 Lbs. (22.2 kg)

B616S-22A-9/16

Fluoreescent Fixture Hanger with Stud

• Design Load 150 Lbs. (.67 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Includes:

2 pcs. 3/8” Flat washers for use with 3/8” ATR

• Allows more than 1/2” (12.7) space

between channel and fixture

• Material: 14 gauge (1.9)

• Standard finish: ZN

• Wt./C 49 Lbs. (22.2 kg)

B616TG-9/16

Fluoreescent Fixture Hanger

for 1/2” (15) Knockout

• Design Load 150 Lbs. (.67 kN)

• Safety Factor of 3

• Maximum design load

50 Lbs. (.22 kN) when used as a

fixture support

• Includes:

2 pcs. 3/8” Flat washers for

use with 3/8” ATR

• Design Load 150 Lbs. (.67 kN)

• Allows more than 1/2” (12.7) space

between channel and fixture

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 32 Lbs. (14.5 kg)

B215S

Channel Hanger

• Can be used with 3/8” & 1/2” threaded rod or 3/8” & 1/2” conduit

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• For use with B42, B52, B54 & B56 channels

• Hardware included:

One (1) 3/8” x 11/2” FFW for use with 3/8”-16 ATR

One (1) 1/2” FW for use with 1/2”-13 ATR

One (1) 5/8” FW for use with 3/8” conduit

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 31 Lbs. (14.0 kg)

B216S

Channel Hanger

• Can be used with 3/8” & 1/2” threaded rod or

3/8” & 1/2” conduit

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• For use with B22, B24, B26 & B32 channels

• Hardware included:

One (1) 3/8” x 11/2” FFW for use with 3/8”-16 ATR

One (1) 1/2” FW for use with 1/2”-13 ATR

One (1) 5/8” FW for use with 3/8” conduit

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 38 Lbs. (17.2 kg)

B241S

Channel Hanger

• Can be used with 3/8” & 1/2” threaded rod or 3/8” & 1/2” conduit

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• For use with B11 & B12 channels

• Hardware included:

One (1) 3/8” x 11/2” FFW for use with 3/8”-16 ATR

One (1) 1/2” FW for use with 1/2”-13 ATR

One (1) 5/8” FW for use with 3/8” conduit

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 47 Lbs. (21.3 kg)

51/8”

(130.2)

11/2”

(38.1)

51/8”

(130.2)

11/2”

(38.1)

31/8”

(79.4)

11/2”

(38.1)

9/16” (14.3) Dia. For

1/2” ATR

7/8” (22.2) Dia.

23/16”

(55.5)

31/2”

(88.9)

121/32”

(42.0)

7/8” (22.2) Dia.

7/8” (22.2) Dia.

121/32”

(42.0)

51/16”

(128.6)

121/32”

(42.0)

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Fluorescent Fixture Hangers

209 B-Line series strut systems Eaton

B390BX

360° Swivel Box Connector

• Design Load 250 Lbs. (1.11 kN) for connector

fitting only

• Safety Factor of 3

• Design Load 50 Lbs. (.22 kN) when used as

illustrated or for use as a fixture support

• Swings 15° in 360° plane

• Includes:

1 pc. 3/4” (20) to 1/2” (15) Conduit reducer

• Fits on 4” box

• Standard finish: ZN

• Wt./C 55 Lbs. (24.9 kg)

B390S

360° Swivel Channel Connector

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Maximum design load 50 Lbs. (.22 kN)

when used as a fixture support

• Swings 15° in 360° plane

• Includes:

2 pcs. SN224-3/4”WO Stud nut

2 pcs. 1/4”-20 Square nut

1 pc. 3/4” (20) to 1/2” (15) Conduit Reducer

• Standard finish: ZN

• Wt./C 71 Lbs. (32.2 kg)

B465

H.I.D. Fixture Hanger

• Design Load 250 Lbs. (1.11 kN)

• Safety Factor of 3

• Swings 15° in 360° plane

• Includes:

1 pc. 3/4” (20) to 1/2” (15) Conduit reducer

• Standard finish: ZN

• Wt./C 95 Lbs. (43.1 kg)

B436S

Fluorescent Fixture Stud Nut

• Bolt size: 1/4” x 11/4”

• Standard finish: ZN

• Wt./C 4 Lbs. (1.8 kg)

• Design Load

250 Lbs. (1.11 kN)

Safety Factor of 3

B436

Fluorescent Fixture Nut

• Standard finish: ZN

• Wt./C 2 Lbs. (.9 kg)

B460

Fluorescent Fixture Hanger

• Hanger is shipped flat and requires

field bending as shown

• Allows more than 1/2” (12.7)

space between channel and fixture

• Material: 18 gauge (1.2)

• Standard finish: ZN

B464

Fluorescent Fixture Hanger

• Hanger is shipped flat and

requires field bending as shown

• Allows more than 1/8” (3.2) space

between channel and fixture

• Material: 18 gauge (1.2)

• Standard finish: ZN

33/4” (95.2)

21/16”

(52.4)

15/8”

(41.3) 9/32” (7.1)

Square Hole

Part No. For Channel Size A Wt./C

In. mm Lbs. kg

B460-22 B22, B24, B26, B32 21/8” (57.5) 17 (7.7)

B460-12 B12 215/16” (79.5) 20 (9.1)

B460-11 B11 33/4” (101.6) 23 (10.4)

A

Tapped For 1/4”-20 Screw

11/4”

(31.7)

Part No. For Channel Size A Wt./C

In. mm Lbs. kg

B464-32 B32 11/2” (40.6) 17 (7.7)

B464-22 B22, B24, B26 13/4” (47.4) 18 (8.1)

B464-12 B12 29/16” (66.0) 21 (9.5)

B464-11 B11 33/8” (91.4) 24 (10.9)

A

1/4” x 1” Round Head

Machine Screw and

1 Square Nut Included /4” x 1” Round Head

Machine Screw and

Square Nut Included

1/4” x 3/4” Carriage Bolt

and Square Nut Included

15/8”

(41.3)

21/8”

(54.0)

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Fluorescent Fixture Hangers

210 Eaton B-Line series strut systems

B516S

Outlet Box

• Duplex cover plate included

• Receptacle not furnished

• Includes:

2 pcs. 1/4”-20 Flat head machine screws

2 pcs. N224WO Channel nuts

• Standard finish: GALV

• Wt./C 98 Lbs. (44.4 kg)

B516

Snap-In Outlet Box

• Provided with #10-32 tapped hole for grounding strap

• Duplex cover plate included

• Receptacle not furnished

• Requires ground wire installation for

use with UL listed channel raceway system

• Standard finish: GALV

• Wt./C 72 Lbs. (32.6 kg)

B203 thru B206

B220 thru B223

X Type End Caps

• Material: 12 gauge (2.6)

• Standard finishes: ZN, GRN,

HDG, SS4

B283 thru B286

End Caps

• Material: 12 gauge (2.6)

• Standard finishes: ZN, GRN

B217-20

Snap Closure Strip for All

15/8” (41.3) Wide Channels

• Refer to Raceway Fill Chart

pages 278-279

• Material: 20 gauge (.9)

• Standard finishes: GRN, GALV, YZN

• Standard length: 120” (3.05m)

• Wt./CFT 36 Lbs. (16.3 kg)

B217P

Plastic Snap Closure Strip for All

15/8” (41.3) Wide Channels

• Refer to Raceway Fill Chart

pages 278-279

• Standard finishes: Green (GRN) or

Gray (GRY) Plastic

• Standard length: 120” (3.05m)

• Wt./CFT 9.2 Lbs. (4.2 kg)

B217-24

Snap Closure Strip for All

15/8” (41.3) Wide Channels

• Refer to Raceway Fill Chart pages 278-279

• For use with 7 or fewer conductors no

larger than #12 AWG

• Material: 24 gauge (.6)

• Standard finishes: GRN, GALV, YZN

• Standard length: 120” (3.05m)

• Wt./CFT 28 Lbs. (12.7 kg)

17/8”

(47.6)

21/8”

(54.0)

41/16”

(103.2)

4”

(101.6)

1/2” (12.7) x

2” (25.4) Slot

B217-20

Closure Strip

1/2” (15) & 3/4” (20)

Concentric KO’S

A Wt./C Part No. Use With

In. mm Lbs. kg

B203 B42 1.015” (25.8) 6 (2.7)

B204 B54 .827” (21.0) 5 (2.2)

B205 B22 1.640” (41.6) 10 (4.5)

B206 B32 1.390” (35.3) 8 (3.6)

B220 B52 .827” (21.0) 4 (1.8)

B221 B12 2.452” (62.3) 15 (6.8)

B222 B11 3.265” (82.9) 20 (9.1)

B223 B24 1.640” (41.6) 10 (4.5)

A

A B Wt./C Part No. Use With In. mm In. mm Lbs. kg

B283 B52 119/32” (40.5) 25/32” (19.8) 6 (2.7)

B284 B54 & B56 119/32” (40.5) 25/32” (19.8) 6 (2.7)

B285 B22 119/32” (40.5) 119/32” (40.5) 13 (5.9)

B286 B24 & B26 119/32” (40.5) 119/32” (40.5) 14 (6.3)

1/2” (12.7) x

2” (25.4) Slot

1/2” (15) & 3/4” (20)

Concentric KO’S

17/8”

(47.6)

15/8”

(41.3)

21/8”

(54.0)

41/16”

(103.2)

6”

(152.4)

A

B

17/16”

(36.5)

19/32”

(15.1)

1/2”

(12.7)

113/32”

(35.7)

15/32”

(11.9)

9/32”

(7.1)

17/16”

(36.5)

5/8”

(15.9)

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Electrical Accessories

211

4Dimension compatible fitting

B-Line series strut systems Eaton

B447A

Conduit Connection Plate for 3/4” (20) Conduit

• Includes:

2 pcs. 1/4”-20 Flat head machine screws

2 pcs. N224WO Channel nuts

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 35 Lbs. (15.9 kg)

B447

Conduit Connection Plate for 1/2” (15) Conduit

• Includes:

2 pcs. 1/4”-20 Flat head machine screws

2 pcs. N224WO Channel nuts

• Material: 16 gauge (1.5)

• Standard finish: ZN

• Wt./C 35 Lbs. (15.9 kg)

B392-32 Series

Connection End Cap

• Includes:

1 pc. 1/4”-20 Square nut

1 pc. B436S Fixture stud nut

• Material: 11 gauge (3.0)

• Standard finish: ZN

B392-22 Series

Connection End Cap

• Includes:

1 pc. 1/4”-20 Square nut

1 pc. B436S Fixture stud nut

• Material: 11 gauge (3.0)

• Standard finish: ZN

B392-12 Series

Connection End Cap

• Includes:

1 pc. 1/4”-20 Square nut

1 pc. B436S Fixture stud nut

• Material: 11 gauge (3.0)

• Standard finish: ZN

B392-11 Series

Connection End Cap

• Includes:

1 pc. 1/4”-20 Square nut

1 pc. B436S Fixture stud nut

• Material: 11 gauge (3.0)

• Standard finish: ZN

7/8” (22.2) Dia.

2 Holes

9/32” (7.1) Dia.

2 Holes

9/32” (7.1) Dia.

5/8”

(15.9)

15/8”

(41.3)

13/8” (34.9)

3/4”

(19.0)

A Dia

9/32” (7.1) Dia.

15/8”

(41.3)

27/16”

(61.9)

3/4”

(19.0)

A Dia

9/32” (7.1) Dia.

13/32” (27.8) Dia. 5/8”

(15.9)

51/8”

(130.2)

A Conduit SIze Wt./C

Part No. In. mm In. mm Lbs. kg

B392-22-1/2 7/8” (22.2) 1/2” (15) 21 (9.5)

B392-22-3/4 11/16” (27.0) 3/4” (20) 20 (9.1)

B392-22-1 1” Pipe Thread 1” (25) 17 (7.7)

15/8”

(41.3)

15/8”

(41.3)

3/4”

(19.0)

A Dia.

9/32” (7.1) Dia.

15/8”

(41.3)

31/4”

(82.5)

3/4”

(19.0)

A Dia

9/32” (7.1) Dia.

51/8”

(130.2)

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Electrical Accessories

212

A Conduit SIze Wt./C

Part No. In. mm In. mm Lbs. kg

B392-11-1/2 7/8” (22.2) 1/2” (15) 36 (16.3)

B392-11-3/4 11/16” (27.0) 3/4” (20) 33 (14.9)

B392-11-1 1” Pipe Thread 1” (25) 32 (14.5)

A Conduit SIze Wt./C

Part No. In. mm In. mm Lbs. kg

B392-12-1/2 7/8” (22.2) 1/2” (15) 27 (12.2)

B392-12-3/4 11/16” (27.0) 3/4” (20) 26 (11.8)

B392-12-1 1” Pipe Thread 1” (25) 23 (10.4)

A Conduit SIze Wt./C

Part No. In. mm In. mm Lbs. kg

B392-32-1/2 7/8” (22.2) 1/2” (15) 20 (9.1)

B392-32-3/4 11/16” (27.0) 3/4” (20) 19 (8.6

Eaton B-Line series strut systems

Wt./C

Part No. Includes Lbs. kg

B718-1 1 B718 & 1 B719 205 (93.0)

B718-2 1 B718 & 2 B719 230 (104.3)

B718-3 1 B718 & 3 B719 255 (115.6)

B718-4 1 B718 & 4 B719 280 (127.0)

Channel Connection Kit

• For use with B22, B24 & B26 channels.

• Box Dimension: Standard 4” octagon box

• Includes:

1 pc. B392-22-3/4 End connection (See page 212)

1 pc. 3/4” (20) Insulated chase nipple

1 pc. 3/4” (20) Lock nut

• Standard finish: ZN

Box Dimension:

21/2” (63.5 Deep x

51/8” (130.2) Square

B718

Universal Junction Bob

• Assemble B719 Hubs into B718 square knockouts

• Designed for use with B22, B24 & B26 channel

• B718 Includes:

1 pc. Junction box only

1 pc. Cover only

2 pcs. #10-20 Round head machine screws

• Standard finish: ZN

• Wt./C 180 Lbs. (81.6 kg)

B719AL

Universal Junction Box Hub

• B719AL Includes:

1 pc. B719AL Hub only

1 pc. B436S Fixture stud nut

1 pc. 1/4”-20 Square nut

2 pcs. #10-24 Self tapping ncrews

2 pcs. Rubber caps

• Material: Aluminum

• Wt./C 25 Lbs. (11.3 kg)

B518-1 thru B518-4

Universal Junction Box & Hubs

• Channel connection kits as shown in the chart above

• Includes:

1 pc. Junction box with screws

1 pc. Box cover

• Standard finish: ZN

B718-1

End

B718-2

90°

B718-3

Tee

B718-4

Cross

B718-2

Thru Box

Channel Connection Wt./C

Part No. Kits Included Lbs. kg

B518-1 1 106 (48.1)

B518-2 2 137 (62.1)

B518-3 3 162 (78.5)

B518-4 4 192 (87.1)

Selection Guide

Selection Guide

B518-1

End

B518-2

90°

B518-3

Tee

B518-4

Cross

B518-2

Thru Box

3/4” (19.1) Conduit

Knockouts Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Junction Boxes

213 B-Line series strut systems Eaton

B766 Series

Straight Strut Joiner

• Includes: 2 Cam screws

• Material: 12 gauge (2.6)

• Standard finish: ZN

B768 Series

Tee Strut Joiner

• Includes: 3 Cam screws

• Patented

• Material: 12 gauge (2.6)

• Standard finish: ZN

B769 Series

Cross Strut Joiner

• Includes: 4 Cam screws

• Patented

• Material: 12 gauge (2.6)

• Standard finish: ZN

B767 Series

90° Elbow Strut Joiner

• Includes: 2 Cam screws

• Material: 12 gauge (2.6)

• Standard finish: ZN

41/2”

(114.3)

7/8”

(22.2)

41/2”

(114.3)

31/16”

(77.8)

25/16”

(58.7)

Wt./C

Part No. For Channel Size Lbs. kg

B766-11 B11 94 (42.6)

B766-12 B12 72 (32.6)

B766-22 * B22 & B24 50 (22.7)

B766-26 B26 53 (24.0)

B766-32 B32 44 (19.9)

B766-42 B42 34 (15.4)

B766-52 B52 & B54 28 (12.7)

B766-56 B56 31 (14.0)

41/2”

(114.3)

41/2”

(114.3)

Note: B767-22

(Cast Aluminum Fitting)

does not require miter

cutting of channel as

shown in drawing.

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Strut Joiners

214

Wt./C

Part No. For Channel Size Lbs. kg

B767-11 B11 74 (33.5)

B767-12 B12 56 (25.4)

B767-22 * B22 & B24 39 (17.7)

B767-26 B26 41 (18.6)

B767-32 B32 34 (15.4)

B767-42 B42 27 (12.2)

B767-52 B52 & B54 23 (10.4)

B767-56 B56 25 (11.3)

Wt./C

Part No. For Channel Size Lbs. kg

B769-11 B11 148 (67.1)

B769-12 B12 120 (54.4)

B769-22 * B22 & B24 87 (39.4)

B769-26 B26 93 (42.2)

B769-32 B32 78 (35.4)

B769-42 B42 65 (29.5)

B769-52 B52 & B54 58 (26.3)

B769-56 B56 62 (28.1)

Wt./C

Part No. For Channel Size Lbs. kg

B768-11 B11 142 (64.4)

B768-12 B12 112 (50.8)

B768-22 * B22 & B24 79 (35.8)

B768-26 B26 79 (35.8)

B768-32 B32 72 (32.6)

B768-42 B42 62 (28.1)

B768-52 B52 & B54 57 (25.8)

B768-56 B56 60 (27.2)

Note: Strut joiners are not for structural support. A channel support is recommended within 24” (609 mm) of each joint.

* Cast aluminum parts * Cast aluminum parts

* Cast aluminum parts * Cast aluminum parts

Eaton B-Line series strut systems

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Strut Joiners & Electrical Hardware

215

B166-46

Four Hole Splice Clevis

Assembly

• Requires ground wire for use with

UL listed channel raceway system

• Includes:

1 Splice clevis

1 pc. B466W tapped plate

4 pcs. 1/4”-20 Flat Head Machine Screws

• Material: 16 gauge (1.5)

• Standard finishes: ZN, GRN

B166

Four Hole Splice Clevis

• Includes:

1 Splice clevis

4 pcs. 1/4”-20 Flat head

machine screws

4 pcs. N224WO channel nuts

• Material: 16 gauge (1.5)

• Standard finishes: ZN, GRN

A For Channel Size Wt./C

Part No. In. mm Lbs. kg

B166-11 31/4” (82.5) B11 128 (58.0)

B166-12 27/16” (61.9) B12 108 (49.0)

B166-22 15/8” (41.3) B22, B24, B26 91 (40.3)

B166-32 13/8” (34.9) B32 83 (37.6)

B166-42 1” (25.4) B42 75 (34.0)

B166-52 13/16” (20.6) B52, B54, B56 71 (32.2)

A

111/16”

(42.9)

71/4”

(184.1)

A For Channel Size Wt./C

Part No. In. mm Lbs. kg

B166-46-11 31/4” (82.5) B11 118 (53.5)

B166-46-12 27/16” (61.9) B12 98 (44.4)

B166-46-22 15/8” (41.3) B22, B24, B26 79 (35.8)

B166-46-32 13/8” (34.9) B32 73 (33.1)

B166-46-42 1” (25.4) B42 65 (29.5)

B166-46-52 13/16” (20.6) B52, B54, B56 61 (27.6)

A

71/4”

(184.1)

111/16”

(42.9)

B166CL

Splice Clevis Clip

• Use to cover gap between strut

• Material: 18 gauge (1.2)

• Standard finish: ZN

• Wt./C 4 Lbs. (1.8 kg)

B619

Knock-Out Plate

• Requires ground wire for use with UL

listed channel raceway system

• Includes: 2 pcs. 1/4”-20 Flat head machine screws

2 pcs. N224WO Channel nuts

• Material: 16 gauge (1.5) - 1/2” (15) conduit knockouts

• Standard finish: ZN

• Wt./C 40 Lbs. (18.1 kg)

B393-1

Wiring Stud

• Requires ground wire for use

with UL listed channel raceway

system

• 1/2” (15) pipe threads

• Material: Cast aluminum

• Wt./C 6 Lbs. (2.7 kg)

B589

Spacer Clevis

• Can be used with B393-1

wiring stud

• Material: 12 gauge (2.6)

• Standard finish: ZN

• Wt./C 29 Lbs. (13.1 kg)

125/32”

(45.2)

1”

(25.4)

B166

9/32” (7.1) Dia.

Holes

121/32”

(42.0)

61/4”

(158.7)

11/8”

(28.6)

1/2” (15) Pipe

Threads

7/8” (22.2) Dia.

1/4”

(12.7)

4”

(101.6)

2”

(50.8)

B590

Fiber Wire Retainer

• Installation aid for retaining

wires before installing

snap closure strip

• Wt./C 1 Lb. (.4 kg)

B617

Shoulder Bolt

• Standard finish: ZN

• Wt./C 6 Lbs. (2.7 kg)

13/8”

(34.9) 11/2”

(38.1)

1/32”

(0.8)

3/8”-16 Thread Size

2”

(50.8)

B-Line series strut systems Eaton

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Electrical Hardware & Porcelain Saddles

216

B446A

Swivel Hanger (Female Only)

• Design Load:

(3/8)-610 Lbs. (2.71 kN)

(1/2)-1130 Lbs. (5.02 kN)

• Safety Factor of 3

• Standard finish: ZN

B446B

Swivel Hanger (Male Only)

• Design Load:

(3/8)-610 Lbs. (2.71 kN)

(1/2)-1130 Lbs. (5.02 kN)

• Safety Factor of 3

• Standard finish: ZN

B446C

Swivel Hanger (Female-Female)

• Design Load:

(3/8)-610 Lbs. (2.71 kN)

(1/2)-1130 Lbs. (5.02 kN)

• Safety Factor of 3

• Standard finish: ZN

B

23/4”

(69.8)

1”

(25.4)

13/4”

(44.1)

A R 13/4”

(44.1)

R B

23/4”

(69.8)

A

A

B446

Swivel Hanger (Female-Male)

• Design Load:

(3/8)-610 Lbs. (2.71 kN)

(1/2)-1130 Lbs. (5.02 kN)

• Safety Factor of 3

• Standard finish: ZN

A

A R Wt./C

Part No. In. mm Lbs. kg

B446B-3/8 3/8”-16 HHCS 9/32” (7.1) 16 (7.2)

B446B-1/2 1/2”-13 HHCS 3/8” (9.5) 20 (9.1)

A R Wt./C

Part No. In. mm Lbs. kg

B446A-3/8 3/8”-16 HN 9/32” (7.1) 13 (5.9)

B446A-1/2 1/2”-13 HN 3/8” (9.5) 15 (6.8)

A B Wt./C

Part No. Lbs. kg

B446-3/8 3/8”-16 HN 3/8”-16 HHCS 28 (12.7)

B446-1/2 1/2”-13 HN 1/2”-13 HHCS 36 (16.3)

A Wt./C

Part No. Lbs. kg

B446C-3/8 3/8”-16 HN 26 (11.8)

B446C-1/2 1/2”-13 HN 31 (14.0)

B4094 & B4095

Porcelain Cable Rack Saddle

• Electrical porcelain has an

dielectric strength of 50 volts/mil

• Designed for use with

B449 brackets

B4050 & B4051

Porcelain Cable Channel Saddle

• Electrical porcelain has an

dielectric strength of

50 volts/mil

x

A

R

21/4”

(57.1)

x

A

R

3”

(76.2)

A R Wt./C

Part No. In. mm In. mm Lbs. kg

B4094 27/8” (73.0) 13/8” (34.9) 67 (30.4)

B4095 37/8” (98.4) 21/8” (54.0) 106 (48.1)

A R Wt./C

Part No. In. mm In. mm Lbs. kg

B4050 3” (76.2) 13/8” (34.9) 72 (32.6)

B4051 4” (101.6) 21/8” (54.0) 100 (45.3)

Eaton B-Line series strut systems

Hole Dia. Wt./C A B Includes

Part No. In. mm Lbs. kg In. mm In. mm Clamp No.

B4060 3/8” (9.5) 25 (11.3)

B4061 1/2” (12.7) 25 (11.3) 1.36” (34.5) .56” (14.2) B2030

B4062 5/8” (15.9) 25 (11.3)

B4063 3/4” (19.0) 37 (16.8)

B4064 7/8” (22.2) 37 (16.8) 1.86” (47.2) .81” (20.8) B2011 B4065 1” (25.4) 37 (16.8)

B4066 11/8” (28.6) 37 (16.8)

B4067 11/4” (31.7) 58 (26.3)

B4068 13/8” (34.9) 58 (26.3)

2.36” (59.9) 1.06” (26.9) B2038 B4069 11/2” (38.1) 58 (26.3)

B4070 15/8” (41.3) 58 (26.3)

B4071 13/4” (44.4) 76 (34.5)

B4072 17/8” (47.6) 76 (34.5)

2.86” (72.6) 1.31” (33.3) B2042 B4073 2” (50.8) 76 (34.5)

B4074 21/8” (54.0) 76 (34.5)

B4075 21/4” (57.1) 90 (40.8)

B4076 23/8” (60.3) 90 (40.8)

3.36” (85.3) 1.56” (39.6) B2046 B4077 21/2” (63.5) 90 (40.8)

B4078 25/8” (66.7) 90 (40.8)

B4079 23/4” (69.8) 109 (49.4)

B4080 27/8” (73.0) 109 (49.4)

3.86” (98.0) 1.81” (46.0) B2050 B4081 3” (76.2) 109 (49.4)

B4082 31/8” (79.4) 109 (49.4)

B4083 31/4” (82.5) 130 (58.9)

B4084 33/8” (85.7) 130 (58.9)

4.36” (110.7) 2.06” (52.3) B2054 B4085 31/2” (88.9) 130 (58.9)

B4086 35/8” (92.1) 130 (58.9)

B4087 33/4” (95.2) 160 (72.6)

B4088 37/8” (98.4) 160 (72.6) 4.86” (123.4) 2.31” (58.7) B2058 B4089 4” (101.6) 160 (72.6)

B4090 41/8” (104.8) 160 (72.6)

B4091 41/4” (107.9) 160 (72.6)

B4092 43/8” (111.1) 160 (72.6) 5.24” (133.1) 2.50” (63.5) B2018

B4093 41/2” (114.3) 160 (72.6)

B4060 THRU B4093

Insulclamp™ Cable Clamps (Replaces porcelain clamps)

• Assembly includes:

1 Insulclamp & 1 pr. zinc plated pipe straps with Everdur (Silicon Bronze) hardware

• The thermoplastic elastomer Insulclamp has a dielectric strength of 640 volts/mil

• The flame retardant one piece design allows for trouble free assembly

• Everdur hardware is non-ferrous and prevents magnetic induction

B

A

Hole Dia.

Electrical Accessories

Reference page 206 for general fitting and standard finish specifications. U.L. Wire Fill Chart on pages 272 - 273.

Insulclamp Clamps

217

OSO

4Dimension compatible fitting

open side only OSO

B-Line series strut systems Eaton

Aluminum

Aluminum channels, fittings and accessories offer excellent corrosion resistance and are suitable for many indoor

and outdoor applications. Aluminum’s high strength to weight ratio helps greatly reduce overall cost of installation

through ease of handling and cutting. Channels are extruded from aluminum alloy 6063-T6. Closure strips are

extruded from aluminum alloy 6063-T5. Fittings and accessories are made from aluminum alloy 5052-H32.

Stainless Steel

Where corrosion problems persist and other material and fittings are ineffective, we recommend use of corrosion

resistant stainless steel channels and accessories. Channels and fittings are available in two types of stainless steel:

SS4-AISI Type 304

SS6-AISI Type 316

Fittings

Most fittings, as shown in this catalog, can be supplied in aluminum or stainless steel.

Consult factory for possible minimum production quantities and set-up charges.

Load Data

Aluminum

Channel’s approximate load data can be determined by multiplying load data in the

steel channel section of this catalog by a factor of 0.38.

Stainless Steel

Channel load data is the same as the data in the steel channel section of this catalog.

Metric

Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.

Alum. & Stainless Steel Materials

Aluminum & Stainless Steel

218 Eaton B-Line series strut systems

B11AL

• Thickness: .105 (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: Aluminum

• Weight: 1.06 Lbs./Ft. (1.58 kg/m)

B12AL

• Thickness: .105 (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: Aluminum

• Weight: .86 Lbs./Ft. (1.28 kg/m)

27/16”

(61.9)

15/8”

(41.3)

31/4”

(82.5)

15/8”

(41.3)

B22AAL

• Thickness: .105 (2.6 mm)

• Standard Length: 10’ (3.05 m) and 20’ (6.09 m)

• Material: Aluminum

• Weight: 1.18 Lbs./Ft. (1.75 kg/m)

15/8”

(41.3)

31/4”

(82.5)

B54AL

• Thickness: .080 (2.0 mm)

• Standard Length: 10’ (3.05 m) and 20’ (6.09 m)

• Material: Aluminum

• Weight: .37 Lbs./Ft. (0.55 kg/m)

15/8”

(41.3)

13/16”

(20.6)

B22AL

• Thickness: .105 (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: Aluminum

• Weight: .66 Lbs./Ft. (0.98 kg/m)

15/8”

(41.3)

15/8”

(41.3)

B24AL

• Thickness: .080 (2.0 mm)

• Standard Length: 10’ (3.05 m) and 20’ (6.09 m)

• Material: Aluminum

• Weight: .52 Lbs./Ft. (0.77 kg/m)

15/8”

(41.3)

15/8”

(41.3)

B54AAL

• Thickness: .080 (2.0 mm)

• Standard Length: 10’ (3.05 m) and 20’ (6.09 m)

• Material: Aluminum

• Weight: .57 Lbs./Ft. (0.84 kg/m)

15/8”

(41.3)

15/8”

(41.3)

B217AL

Closure Strip

• Standard Length: 10’ (304.8 cm)

• Material: Aluminum

• Weight: .15 Lbs./Ft. (0.23 kg/m)

B217P

Plastic Closure Strip

• Standard Length: 10’ (304.8 cm)

• Material: PVC

• Weight: .09 Lbs./Ft. (0.14 kg/m)

B217FFAL

Closure Strip

• Standard Length: 10’ (304.8 cm)

• Material: Aluminum

• Weight: .16 Lbs./Ft. (0.24 kg/m)

17/16”

(36.5)

21/2”

(63.5)

17/16”

(36.5)

5/8”

(15.9)

Alum. & Stainless Steel Materials

Reference page 218 for general fitting specifications. Other channel combinations available-see steel section for styles.

Aluminum Channel & Closure Strips

219 B-Line series strut systems Eaton

SH Type Channel

• Material: Aluminum

H-17/8 Type Channel

• Material: Aluminum

B2000 Series

Rigid Conduit Clamps

• Safety Factor of 5

• Machine Screw and Square Nut included

• Pipe clamp material 5052-H32

KO6 Type Knockout Channel

• Material: Aluminum

Thickness H Wt./C

Part No. in. mm in. mm Lbs./Ft. kg/m

B12SH AL .105 (2.6) 27/16” (61.9) .83 (1.23)

B22SH AL .105 (2.6) 15/8” (41.3) .63 (.93)

B24SH AL .080 (2.0) 15/8” (41.3) .49 (.73)

B54SH AL .080 (2.0) 13/16” (20.6) .34 (.50)

Thickness H Wt./C

Part No. in. mm in. mm Lbs./Ft. kg/m

B12KO6 AL .105 (2.6) 27/16” (61.9) .86 (1.28)

B22KO6 AL .105 (2.6) 15/8” (41.3) .66 (.98)

B24KO6 AL .080 (2.0) 15/8” (41.3) .52 (.77)

B54KO6 AL .080 (2.0) 13/16” (20.6) .37 (.56)

Conduit or Material Design

Part No. Pipe Size Thickness Load Wt./C

in. mm in. mm Lbs. kN Lbs. kg

B2001 AL 3/8” (10) .063 (1.6) 180 (.80) 4 (1.8)

B2008 AL 1/2” (15) .063 (1.6) 180 (.80) 4 (1.8)

B2009 AL 3/4” (20) .080 (2.0) 270 (1.20) 6 (2.7)

B2010 AL 1” (25) .080 (2.0) 270 (1.20) 7 (3.2)

B2011 AL 11/4” (32) .080 (2.0) 270 (1.20) 8 (3.6)

B2012 AL 11/2” (40) .100 (2.5) 360 (1.60) 11 (5.0)

B2013 AL 2” (50) .100 (2.5) 360 (1.60) 12 (5.4)

B2014 AL 21/2” (65) .100 (2.5) 360 (1.60) 13 (5.9)

B2015 AL 3” (80) .100 (2.5) 360 (1.60) 16 (7.2)

B2016 AL 31/2” (90) .125 (3.2) 450 (2.00) 22 (10.0)

B2017 AL 4” (100) .125 (3.2) 450 (2.00) 24 (10.9)

B2018 AL 41/2” (115) .125 (3.2) 450 (2.00) 26 (11.8)

B2019 AL 5” (125) .125 (3.2) 450 (2.00) 27 (12.2)

B2020 AL 6” (150) .125 (3.2) 450 (2.00) 33 (14.9)

2” TYP.

(50.8)

H

9/16” x 11/8” Slots

(14.2) (28.6)

H

9/16” (14.2) Dia. Holes

6”

(152.4)

3”

(76.2)

H

7/8” (22.2) Dia. KO

17/8” Typ.

(47.6)

Design Load

Alum. & Stainless Steel Materials

Reference page 218 for general fitting specifications. Other channel combinations available-see steel section for styles.

Aluminum

220

Thickness H Wt./C

Part No. in. mm in. mm Lbs./Ft. kg/m

B12H17/8 AL .105 (2.6) 27/16” (61.9) .86 (1.28)

B22H17/8 AL .105 (2.6) 15/8” (41.3) .66 (.98)

B24H17/8 AL .080 (2.0) 15/8” (41.3) .52 (.77)

B54H17/8 AL .080 (2.0) 13/16” (20.6) .37 (.55)

Eaton B-Line series strut systems

Part Number

With Without Thread Thickness Wt./C

Spring Spring Size in. mm Lbs. kg

N724SS6 N224WOSS6 1/4”-20 1/4” (6.3) 6.6 (3.0

N728SS6 N228WOSS6 3/8”-16 3/8” (9.5) 10.6 (4.8)

N725SS6 N225WOSS6 1/2”-13 3/8” (9.5) 9.7 (4.4)

Part Number

With Without Thread Thickness Wt./C

Spring Spring Size in. mm Lbs. kg

N224SS6 N224WOSS6 1/4”-20 1/4” (6.3) 6.6 (3.0)

N228SS6 N228WOSS6 3/8”-16 3/8” (9.5) 10.6 (4.8)

N225SS6 N225WOSS6 1/2”-13 3/8” (9.5) 9.7 (4.4)

Part Number

With Without Thread Thickness Wt./C

Spring Spring Size in. mm Lbs. kg

N524SS6 N224WOSS6 1/4”-20 1/4” (6.3) 6.6 (3.0)

N528SS6 N228WOSS6 3/8”-16 3/8” (9.5) 10.6 (4.8)

N525SS6 N525WOSS6 1/2”-13 3/8” (9.5) 9.7 (4.4)

Nuts for B12 Channel

Nuts for B22, B24 Channels

Nuts for B54 Channel

Aluminum Fittings

Most fittings, as shown in this catalog, can be supplied in aluminum. See “Fittings” section (page 106) of this catalog.

Consult factory for possible minimum production quantities and set-up charges.

Channel Nuts

We recommend the use of Stainless Steel channel nuts with Aluminum channel. For channel nut pull-out strength and

slip resistance, use the channel nut information provided on pg. 84 & 85.

A (.70) multiplier is to be applied to obtain the appropriate derated values for aluminum channel.

Spring Nut Nut Without Spring

Alum. & Stainless Steel Materials

Reference page 218 for general fitting specifications. Other channel combinations available-see steel section for styles.

Aluminum

221 B-Line series strut systems Eaton

SH Type Channel H-17/8 Type Channel

B22SS_

• _ Substitute 4 for Stainless Steel

Type 304 or 6 for Stainless Steel

Type 316

• Thickness: 12 Ga. (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4, SS6

• Weight: 1.90 Lbs./Ft. (2.83 kg/m)

B32SS4

• Thickness: 12 Ga. (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4

• Weight: 1.70 Lbs./Ft. (2.53 kg/m)

B42SS4

• Thickness: 12 Ga. (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4

• Weight: 1.44 Lbs./Ft. (2.14 kg/m)

B24SS_

• _ Substitute 4 for Stainless Steel

Type 304 or 6 for Stainless Steel

Type 316

• Thickness: 14 Ga. (1.9 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4, SS6

• Weight: 1.40 Lbs./Ft. (2.08 kg/m)

B52SS_

• _ Substitute 4 for Stainless Steel

Type 304 or 6 for Stainless Steel

Type 316

• Thickness: 12 Ga. (2.6 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4, SS6

• Weight: 1.27 Lbs./Ft. (1.89 kg/m)

9/16” x 7/8” Slots

(14.2) (22.2)

2” Typ.

(50.8)

H

H

9/16” (14.2) Dia. Holes

17/8” Typ.

(47.6)

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3)

13/8”

(34.9) 1”

(25.4)

13/16”

(20.6)

15/8”

(41.3)

B54SS_

• _ Substitute 4 for Stainless Steel

Type 304 or 6 for Stainless Steel

Type 316

• Thickness: 14 Ga. (1.9 mm)

• Standard Length: 10’ (3.05 m)

and 20’ (6.09 m)

• Material: SS4, SS6

• Weight: .97 Lbs./Ft. (1.44 kg/m)

13/16”

(20.6)

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3) Alum. & Stainless Steel Materials

Reference page 218 for general fitting specifications. Other channel combinations available-see steel section for styles.

Stainless Steel

222

Thickness H Wt./C

Part No. in. mm in. mm Lbs./Ft. kg/m

B22SH SS4 12 Ga. (2.6) 15/8” (41.3) 1.82 (2.70)

B22SH SS6 12 Ga. (2.6) 15/8” (41.3) 1.82 (2.70)

B24SH SS4 14 Ga. (1.9) 15/8” (41.3) 1.34 (1.99)

B24SH SS6 14 Ga. (1.9) 15/8” (41.3) 1.34 (1.99)

B32SH SS4 12 Ga. (2.6) 13/8” (34.9) 1.62 (2.41)

B42SH SS4 12 Ga. (2.6) 1” (25.4) 1.36 (2.02)

B52SH SS4 12 Ga. (2.6) 13/16” (20.6) 1.23 (1.83)

B52SH SS6 12 Ga. (2.6) 13/16” (20.6) 1.23 (1.83)

B54SH SS4 14 Ga. (1.9) 13/16” (20.6) .91 (1.35)

B54SH SS6 14 Ga. (1.9) 13/16” (20.6) .91 (1.35)

Thickness H Wt./C

Part No. in. mm in. mm Lbs./Ft. kg/m

B22H17/8 SS4 12 Ga. (2.6) 15/8” (41.3) 1.85 (2.75)

B22H17/8 SS6 12 Ga. (2.6) 15/8” (41.3) 1.85 (2.75)

B24H17/8 SS4 14 Ga. (1.9) 15/8” (41.3) 1.36 (2.02)

B24H17/8 SS6 14 Ga. (1.9) 15/8” (41.3) 1.36 (2.02)

B32H17/8 SS4 12 Ga. (2.6) 13/8” (34.9) 1.65 (2.45)

B42H17/8 SS4 12 Ga. (2.6) 1” (25.4) 1.39 (2.07)

B52H17/8 SS4 12 Ga. (2.6) 13/16” (20.6) 1.20 (1.83)

B52H17/8 SS6 12 Ga. (2.6) 13/16” (20.6) 1.20 (1.83)

B54H17/8 SS4 14 Ga. (1.9) 13/16” (20.6) .93 (1.38)

B54H17/8 SS6 14 Ga. (1.9) 13/16” (20.6) .93 (1.38)

Eaton B-Line series strut systems

Nuts for B22, B24, B32 Channels

Channel Nuts

• For Channel Nuts pull-out strength and slip resistance, use the

data shown on pages 84 & 85.

Note: Reduce slip load by 50% due to hardness of material.

Nuts for B42, B52, B54 Channels

Stainless Steel Fittings

Most fittings, as shown in this catalog, can be supplied in Type 304 or Type 316 stainless steel. See “Fittings”

section (page 106) of this catalog.

Consult factory for possible minimum production quantities and set-up charges.

B2000 Series

Pipe & Tubing Clamps

• Safety Factor of 5

• Combination recess hex head machine screw and square nut included

• Material: Stainless Steel Type 304 & 316

Spring Nut Nut Without Spring

Design Load Alum. & Stainless Steel Materials

Reference page 218 for general fitting specifications. Other channel combinations available-see steel section for styles.

Stainless Steel

223

Part Number

With Without Thread Thickness Wt./C

Spring Spring Size in. mm Lbs. kg

N224SS6 N224WOSS6 1/4”-20 1/4” (6.3) 6.6 (3.0)

N228SS6 N228WOSS6 3/8”-16 3/8” (9.5) 10.6 (4.8)

N225SS6 N225WOSS6 1/2”-13 3/8” (9.5) 9.7 (4.4)

Part Number

With Without Thread Thickness Wt./C

Spring Spring Size in. mm Lbs. kg

N524SS6 N224WOSS6 1/4”-20 1/4” (6.3) 6.6 (3.0)

N528SS6 N228WOSS6 3/8”-16 3/8” (9.5) 10.6 (4.8)

N525SS6 N525WOSS6 1/2”-13 3/8” (9.5) 9.7 (4.4)

Conduit or Material Design

Part No. Pipe Size Thickness Load Wt./C

in. mm in. mm Lbs. kN Lbs. kg

B2001 SS4 3/8” (10) 16 Ga. (1.5) 400 (1.78) 10 (4.5)

B2008 SS4 1/2” (15) 16 Ga. (1.5) 400 (1.78) 11 (5.0)

B2009 SS4 3/4” (20) 14 Ga. (1.9) 600 (2.67) 15 (6.8)

B2010 SS4 1” (25) 14 Ga. (1.9) 600 (2.67) 16 (7.2)

B2011 SS4 11/4” (32) 14 Ga. (1.9) 600 (2.67) 20 (9.1)

B2012 SS4 11/2” (40) 12 Ga. (2.6) 800 (3.56) 30 (13.6)

B2013 SS4 2” (50) 12 Ga. (2.6) 800 (3.56) 34 (15.4)

B2014 SS4 21/2” (65) 12 Ga. (2.6) 800 (3.56) 38 (17.2)

B2015 SS4 3” (80) 12 Ga. (2.6) 800 (3.56) 44 (19.9)

B2016 SS4 31/2” (90) 12 Ga. (2.6) 1000 (4.45) 51 (23.1)

B2017 SS4 4” (100) 12 Ga. (2.6) 1000 (4.45) 55 (24.9)

B2018 SS4 41/2” (115) 12 Ga. (2.6) 1000 (4.45) 59 (26.7)

B2019 SS4 5” (125) 12 Ga. (2.6) 1000 (4.45) 64 (29.0)

B2020 SS4 6” (150) 12 Ga. (2.6) 1000 (4.45) 80 (36.3)

B-Line series strut systems Eaton

We offer two fire retardant (FR) resins for strut systems: polyester and vinyl ester. Both resins are ideal for corrosive

environments.

While polyester is sufficient for most uses, vinyl ester is suitable for a broader range of environments.

Please refer to the \"Corrosion Resistance Guide\" for specific applications, page 225.

Materials & Finishes

Our Fiberglass Strut systems are manufactured from glass fiber-reinforced plastic shapes that meet ASTM E-84, Class

1 Flame Rating and self-extinguishing requirements of ASTM D-635. A surface veil is applied during pultrusion to ensure

a resin-rich surface and ultraviolet resistance.

Fittings

The following dimensions apply to all fittings except as noted on the drawings:

Hole Size – 13/32” (10.3 mm) Dia.

Hole Spacing – 13/16” (20.6 mm) from end and 17/8” (47.6 mm) on center.

Width – 15/8” (41.3 mm)

Thickness – 1/4” (6.3 mm)

Metric

Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.

Fiberglass Materials

Fiberglass

224 Eaton B-Line series strut systems

Channel Resin Information

We offer two fire retardant (FR) resins for strut systems, polyester and vinyl ester. Both resins are ideal for corrosive

environments. While polyester is sufficient for most uses, vinyl ester is suitable for a broader range of environments.

Please refer to the \"Corrosion Resistance Guide\" below for specific applications.

Corrosion Resistance Guide

Chemicals 70°F (21°C) 160°F (71°C) Chemicals 70°F (21°C) 160°F (71°C)

Acetic acid 5% BFP/BFV BFP/BFV Methyl alcohol 10% BFP/BFV BFV-150° **

Acetic acid 52% BFP/BFV BFV-210° ** Naphtha BFP/BFV BFP/BFV

Aluminum potassium sulfate 5% BFP/BFV BFP/BFV Nitric acid 5% BFP/BFV BFP/BFV

Ammonium hydroxide 10% BFP/BFV BFV-150° ** Nitric acid 20% BFV BFV-120° **

Ammonium nitrate BFP/BFV BFP/BFV Phosphoric acid 10% BFP/BFV BFP/BFV

Benzene sulfonic acid 5% BFP/BFV BFP/BFV Phosphoric acid 30% BFP/BFV BFP/BFV

Calcium chloride BFP/BFV BFP/BFV Phosphoric acid 85% BFP/BFV BFP/BFV

Carbon tetrachloride BFV BFV-100° ** Sodium bicarbonate 10% BFP/BFV BFP/BFV

Chlorine dioxide 15% BFP/BFV BFV-150° ** Sodium bisulfate BFP/BFV BFP/BFV

Chromic acid 5% BFV BFV-150° ** Sodium carbonate BFP/BFV BFV

Copper sulfate BFP/BFV BFP/BFV Sodium chloride BFP/BFV BFP/BFV

Diesel fuel BFP/BFV BFV Sodium hydroxide 1-50% BFV BFV-120° **

Ethylene glycol BFP/BFV BFP/BFV Sodium hypochlorite 5% BFP/BFV BFV-120° **

Fatty acids 100% BFP/BFV BFP/BFV Sodium nitrate BFP/BFV BFP/BFV

Ferrous sulfate BFP/BFV BFP/BFV Sodium silicate BFP/BFV BFV-210° **

Fluosilicic acid 0-20% BFV BFV Sodium sulfate BFP/BFV BFP/BFV

Gasoline BFP/BFV BFV Sulfuric acid 0-30% BFP/BFV BFP/BFV

Hydrochloric acid 1% BFP/BFV BFP/BFV Sulfuric acid 30-50% BFV BFV

Hydrochloric acid 15% BFP/BFV BFV-180° ** Sulfuric acid 50-70% BFV BFV-180° **

Hydrochloric acid 37% BFP/BFV BFV-150° ** Trisodium phosphate 25% BFP/BFV BFV-210° **

Kerosene BFP/BFV BFP/BFV Trisodium phosphate-All BFV BFV-210° **

Magnesium chloride BFP/BFV BFP/BFV Water, Distilled BFP/BFV BFP/BFV

BFP - BFP parts recommended BFV - BFV parts recommended ** - Not recommended to exceed this temperature

Information contained in this chart is based on data from raw material suppliers.

Temperatures are not the minimum nor the maximum (except where specifically stated) but represent standard test

conditions. The products may be suitable at higher temperatures but individual test data should be required to

establish suitability.

The recommendations or suggestions contained in this chart are made without guarantee or representation as to results.

We suggest that you evaluate the recommendations and suggestions in your own laboratory or actual field trial prior to use.

Flame Retardant Properties BFP BFV

Flame Resistance (FTMS 406-2023)

ign/burn, seconds 75/75 75/75

Intermittent Flame Test (HLT-15), rating 100 100

Flammability Test (ASTM D635)

Ignition none none

Burning Time 0 sec. 0 sec.

Surface Burning Characteristics (ASTM E84),

Flame spread index 25 25

UL 94 Flame Class V-0 V-0

Recommended Guideline:

Temperature Design Load Multiplier

75°F (24°C) 100%

100°F (38°C) 90%

125°F (52°C) 78%

150°F (66°C) 68%

175°F (79°C) 60%

200°F (93°C) 52%

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

225 B-Line series strut systems Eaton

15/8”

(41.3)

Part No. Material Description Color Weight

Lbs./ft. kg/m

BFP22* Polyester Resin Solid Back Gray .63 (.94)

BFV22* Vinyl Ester Resin Solid Back Beige .63 (.94)

BFP22H17/8* Polyester Resin Holes in Back Gray .60 (.89)

BFV22H17/8* Vinyl Ester Resin Holes in Back Beige .60 (.89)

BFP22SH* Polyester Resin Slots in Back Gray .61 (.91)

BFV22SH* Vinyl Ester Resin Slots in Back Beige .61 (.91)

BFP22H17/8

BFV22H17/8

9/16” (14.3) holes

17/8” (47.6) on centers

BFP22

BFV22

Solid Back

BFP22 THRU BFV22SH

• Channel lengths: 10 Ft. (3.05 m) and 20 Ft. (6.09 m)

• Fiberglass strut meets specification of ASTM D-4385 Levels III and IV.

BFP22A

BFV22A

• Channel Lengths: 10 Ft. (3.05 m) and 20 Ft. (6.09 m)

• Fiberglass strut meets specification of

ASTM D-4385 Levels III and IV.

BFP22SH

BFV22SH

9/16” (14.3) x 7/8” (22.2) slots

2” (50.8) on centers

13/16” (20.6)

15/8”

(41.3)

31/4”

(82.5)

Part No. Material Description Color Weight

Lbs./ft. kg/m

BFP22A* Polyester Resin Back To Back Gray 1.15 (1.71)

BFV22A* Vinyl Ester Resin Back To Back Beige 1.15 (1.71)

15/8”

* Insert -10 for 10’-0” (41.3) (3.05 m) length or -20 for 20’-0” (6.09 m) length

* Insert -10 for 10’-0” (3.05 m) length or -20 for 20’-0” (6.09 m) length

Temperature Design Load Multiplier

75°F (24°C) 100%

100°F (38°C) 90%

125°F (52°C) 78%

150°F (66°C) 68%

175°F (79°C) 60%

200°F (93°C) 52%

Published design loads on page 227 are based on

usage at 70°F (21°C) and must be reduced for

continuous exposure to higher temperatures.

Refer to the chart below for high temperature

applications.

15/8”

(41.3) BFP22A

BFV22A

Solid Back to

Back

13/16”

(20.6) Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

226

Field Cutting Sealant Kits

RSK010 • Pint Sealing Kit (473 cm3)

includes sealant and brush applicator

• Seals exposed fibers after field cutting

• UV resistant

APPROPRIATE PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION DEVICE SHOULD BE WORN WHEN FIELD CUTTING OR GRINDING FIBERGLASS.

Eaton B-Line series strut systems

WARNING

Maximum Deflection

Beam Allowable @ Maximum Allowable Load @ Deflection =

Span Part Beam Load Allowable

No. Load Beam Load 1/240 Span 1/360 Span

in. mm Lbs. kN in. mm Lbs. kN Lbs. kN

12” (305)

BFP22 1781 (7.92) 0.064 (1.62) 1392 (6.19) 928 (4.13)

BFP22A 2259 (10.05) 0.037 (.94) 2259 (10.05) 2051 (9.12)

24” (609)

BFP22 890 (3.96) 0.256 (6.50) 347 (1.54) 231 (1.03)

BFP22A 1127 (5.01) 0.147 (3.73) 767 (3.41) 511 (2.27)

36” (914)

BFP22 592 (2.63) 0.576 (14.63) 153 (0.68) 101 (0.45)

BFP22A 750 (3.33) 0.330 (8.38) 338 (1.50) 224 (0.99)

48” (1219)

BFP22 443 (1.97) 1.024 (26.01) 85 (0.38) 55 (0.24)

BFP22A 560 (2.49) 0.587 (14.91) 188 (0.83) 123 (0.55)

60” (1524)

BFP22 353 (1.57) 1.600 (40.64) 53 (0.23) 34 (0.15)

BFP22A 446 (1.98) 0.918 (23.32) 117 (0.52) 76 (0.34)

72” (1829)

BFP22 293 (1.30) 2.303 (58.49) 35 (0.15) 22 (0.10)

BFP22A 370 (1.64) 1.322 (33.58) 78 (0.34) 50 (0.22)

96” (2438)

BFP22 218 (0.97) 4.095 (104.01) 17 (0.07) 9 (0.04)

BFP22A 273 (1.21) 2.350 (59.69) 39 (0.17) 23 (0.10)

120” (3048)

BFP22 172 (0.76) 6.398 (162.51) 8 (0.03) 3 (0.01)

BFP22A 214 (0.95) 3.671 (93.24) 19 (0.08) 9 (0.04)

Beam Loading Data for Glass Reinforced Polyester Resin

Beam Loading Data for Glass Reinforced Vinyl Ester Resin

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

227

Loading Information

Beam Loads:

The above charts list the total allowable uniform load for various simple spans based on a minimum safety factor of 2. If the load

is concentrated at center span, multiply the load from the above charts by 0.5 and the corresponding deflection by 0.8.

All beams should be supported in a manner to prevent rotation at supports. Long, deep beams should be tied between supports

to prevent twist. For channels with holes or slots use 90% of recommended load shown in channel loading chart.

Maximum Deflection

Beam Allowable @ Maximum Allowable Load @ Deflection =

Span Part Beam Load Allowable

No. Load Beam Load 1/240 Span 1/360 Span

in. mm Lbs. kN in. mm Lbs. kN Lbs. kN

12” (305)

BFV22 2220 (9.87) 0.071 (1.80) 1568 (6.97) 1045 (4.65)

BFV22A 6442 (28.65) 0.039 (0.99) 6442 (29.65) 5549 (24.68)

24” (609)

BFV22 1109 (4.93) 0.283 (7.19) 391 (1.74) 260 (1.15)

BFV22A 3219 (14.32) 0.155 (3.94) 2079 (9.25) 1385 (6.16)

36” (914)

BFV22 738 (3.28) 0.637 (16.18) 172 (0.76) 114 (0.51)

BFV22A 2144 (9.53) 0.348 (8.84) 922 (4.10) 613 (2.72)

48” (1219)

BFV22 553 (2.46) 1.133 (28.78) 96 (0.43) 63 (0.28)

BFV22A 1606 (7.14) 0.619 (15.72) 516 (2.29) 342 (1.52)

60” (1524)

BFV22 441 (1.96) 1.770 (44.96) 60 (0.26) 39 (0.17)

BFV22A 1283 (5.70) 0.967 (24.56) 327 (1.45) 216 (0.96)

72” (1829)

BFV22 366 (1.63) 2.549 (64.74) 40 (0.18) 25 (0.11)

BFV22A 1067 (4.74) 1.393 (35.38) 224 (0.99) 147 (0.65)

96” (2438)

BFV22 273 (1.21) 4.531 (115.09) 19 (0.08) 11 (0.05)

BFV22A 796 (3.54) 2.477 (62.91) 121 (0.54) 78 (0.34)

120” (3048)

BFV22 216 (0.96) 7.079 (179.80) 9 (0.04) 7 (0.02)

BFV22A 633 (2.81) 3.870 (98.30) 72 (0.32) 44 (0.19)

B-Line series strut systems Eaton

13/16”

(20.6)

1”

(25.4)

Part No. Material Description Color Weight

Lbs./ft. kg/m

BFP42* Polyester Resin Solid Back Gray .48 (.71)

BFV42* Vinyl Ester Resin Solid Back Beige .48 (.71)

BFP42H17/8* Polyester Resin Holes in Back Gray .46 (.68)

BFV42H17/8* Vinyl Ester Resin Holes in Back Beige .46 (.68)

BFP42SH* Polyester Resin Slots in Back Gray .47 (.70)

BFV42SH* Vinyl Ester Resin Slots in Back Beige .47 (.70)

BFP42H17/8

BFV42H17/8

9/16” (14.3) holes

17/8” (47.6) on centers

BFP42

BFV42

Solid Back

BFP42 thru BFV42SH

• Channel lengths: 10 Ft. (3.05 m) and 20 Ft. (6.09 m)

• Fiberglass strut meets specification of ASTM D-4385 Levels III and IV.

BFP42A

BFV42A

Solid Back to Back

BFP42A

BFV42A

• Channel lengths: 10 Ft. (3.05 m) and 20 Ft. (6.09 m)

• Fiberglass strut meets specification of

ASTM D-4385 Levels III and IV.

BFP42SH

BFV42SH

9/16” (14.3) x 7/8” (22.2) slots

2” (50.8) on centers

15/8”

(41.3)

* Insert -10 for 10’-0” (3.05 m) length or -20 for 20’-0” (6.09 m) length

* Insert -10 for 10’-0” (3.05 m) length or -20 for 20’-0” (6.09 m) length

Published design loads on page 229 are based on

usage at 70°F (21°C) and must be reduced for

continuous exposure to higher temperatures.

Refer to the chart below for high temperature

applications.

2”

(50.8)

1”

(25.4)

Part No. Material Description Color Weight

Lbs./ft. kg/m

BFP42A* Polyester Resin Back To Back Gray .85 (1.26)

BFV42A* Vinyl Ester Resin Back To Back Beige .85 (1.26)

13/16”

(20.6)

15/8”

(41.3)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

228

Temperature Design Load Multiplier

75°F (24°C) 100%

100°F (38°C) 90%

125°F (52°C) 78%

150°F (66°C) 68%

175°F (79°C) 60%

200°F (93°C) 52%

APPROPRIATE PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION DEVICE SHOULD BE WORN WHEN FIELD CUTTING OR GRINDING FIBERGLASS.

Eaton B-Line series strut systems

Field Cutting Sealant Kits

RSK010 • Pint Sealing Kit (473 cm3)

includes sealant and brush applicator

• Seals exposed fibers after field cutting

• UV resistant

WARNING

Maximum Deflection

Beam Allowable @ Maximum Allowable Load @ Deflection =

Span Part Beam Load Allowable

No. Load Beam Load 1/240 Span 1/360 Span

in. mm Lbs. kN in. mm Lbs. kN Lbs. kN

12” (305)

BFP42 841 (3.74) 0.104 (2.64) 403 (1.79) 269 (1.19)

BFP42A 2325 (10.34) 0.060 (1.52) 1948 (8.66) 1299 (5.78)

24” (609)

BFP42 420 (1.87) 0.417 (10.59) 100 (0.44) 66 (0.29)

BFP42A 1161 (5.16) 0.239 (6.07) 486 (2.16) 323 (1.43)

36” (914)

BFP42 279 (1.24) 0.938 (23.82) 43 (0.19) 29 (0.13)

BFP42A 773 (3.44) 0.537 (13.64) 214 (0.95) 142 (0.63)

48” (1219)

BFP42 208 (0.92) 1.667 (42.34) 23 (0.10) 15 (0.06)

BFP42A 578 (2.57) 0.955 (24.26) 119 (0.53) 78 (0.34)

60” (1524)

BFP42 166 (0.74) 2.604 (66.14) 14 (0.06) 8 (0.03)

BFP42A 461 (2.05) 1.491 (37.87) 74 (0.33) 48 (0.21)

72” (1829)

BFP42 137 (0.61) 3.750 (95.25) 8 (0.03) 5 (0.02)

BFP42A 383 (1.70) 2.148 (54.56) 49 (0.22) 31 (0.14)

96” (2438)

BFP42 101 (0.45) 6.667 (169.34) 3 (0.01) – –

BFP42A 284 (1.26) 3.818 (96.98) 24 (0.10) 14 (0.04)

120” (3048)

BFP42 79 (0.35) 10.417 (264.59) –– ––

BFP42A 224 (0.99) 5.966 (151.53) 11 (0.05) 5 (0.02)

Loading Information

Beam Loads:

The above charts list the total allowable uniform load for various simple spans based on a minimum safety factor of 2. If the load

is concentrated at center span, multiply the load from the above charts by 0.5 and the corresponding deflection by 0.8.

All beams should be supported in a manner to prevent rotation at supports. Long, deep beams should be tied between supports

to prevent twist. For channels with holes or slots use 90% of recommended load shown in channel loading chart.

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

229

Beam Loading Data for Glass Reinforced Polyester Resin

Beam Loading Data for Glass Reinforced Vinyl Ester Resin

Maximum Deflection

Beam Allowable @ Maximum Allowable Load @ Deflection =

Span Part Beam Load Allowable

No. Load Beam Load 1/240 Span 1/360 Span

in. mm Lbs. kN in. mm Lbs. kN Lbs. kN

12” (305)

BFV42 988 (4.39) 0.112 (2.84) 440 (1.96) 293 (1.30)

BFV42A 2865 (12.74) 0.063 (1.60) 2278 (10.13) 1518 (6.75)

24” (609)

BFV42 493 (2.19) 0.448 (11.38) 109 (0.48) 73 (0.32)

BFV42A 1431 (6.36) 0.252 (6.40) 568 (2.52) 378 (1.68)

36” (914)

BFV42 328 (1.46) 1.009 (25.63) 48 (0.21) 31 (0.14)

BFV42A 953 (4.24) 0.566 (14.37) 251 (1.11) 166 (0.74)

48” (1219)

BFV42 245 (1.09) 1.793 (45.54) 26 (0.11) 16 (0.07)

BFV42A 713 (3.17) 1.006 (25.55) 139 (0.62) 92 (0.41)

60” (1524)

BFV42 195 (0.87) 2.802 (71.17) 15 (0.06) 9 (0.04)

BFV42A 569 (2.53) 1.572 (39.93) 87 (0.38) 57 (0.25)

72” (1829)

BFV42 162 (0.72) 4.035 (102.49) 9 (0.04) 5 (0.02)

BFV42A 473 (2.10) 2.264 (57.50) 58 (0.26) 37 (0.16)

96” (2438)

BFV42 120 (0.53) 7.173 (182.19) 3 (0.01) 1 (0.004)

BFV42A 351 (1.56) 4.025 (102.23) 29 (0.13) 17 (0.07)

120” (3048)

BFV42 94 (0.42) 11.207 (284.66) –– ––

BFV42A 278 (1.23) 6.288 (159.71) 14 (0.06) 7 (0.03)

B-Line series strut systems Eaton

Nominal Thread Design Load Design Load Maximum

Part No. Pipe Size Size A B Torque Wt./C

in. mm Lbs. kN Lbs. kN in.-Lbs. N•m Lbs. kg

BFV501-1/2 1/2 (15) 3/8”-16 300 (1.33) 150 (.67) 30 (3.4) 3.5 (1.59)

BFV501-3/4 3/4 (20) 3/8”-16 300 (1.33) 150 (.67) 30 (3.4) 3.9 (1.77)

BFV501-1 1 (25) 3/8”-16 300 (1.33) 150 (.67) 30 (3.4) 4.4 (1.99)

BFV501-11/4 11/4 (32) 3/8”-16 300 (1.33) 150 (.67) 30 (3.4) 4.8 (2.18)

BFV501-11/2 11/2 (40) 3/8”-16 300 (1.33) 150 (.67) 30 (3.4) 5.2 (2.36)

BFV501-2 2 (50) 1/2”-13 600 (2.67) 200 (.89) 60 (6.8) 7.7 (3.49)

BFV501-21/2 21/2 (65) 1/2”-13 600 (2.67) 200 (.89) 60 (6.8) 10.2 (4.63)

BFV501-3 3 (80) 1/2”-13 600 (2.67) 200 (.89) 60 (6.8) 12.6 (5.71)

BFV501-31/2 31/2 (90) 1/2”-13 600 (2.67) 200 (.89) 60 (6.8) 15.1 (6.85)

BFV501-4 4 (100) 1/2”-13 600 (2.67) 200 (.89) 60 (6.8) 17.6 (7.98)

Load A

Load

B

BFV501 Series

U-Bolts with Hex Nuts

• Design Load Safety Factor of 3

• Load A: Straight down loading

• Load B: Side loading

• Inner surface of U-Bolt is flat to provide additional contact surface area

• Material: Glass reinforced polyurethane

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

230 Eaton B-Line series strut systems

Part No. Thread Pull-Out Slip Resistance Max. Torque Wt./C

With Spring W/O Spring Size Lbs kN Lbs. N in.-Lbs. N•m Lbs. kg

BFV-224 BFV-224WO 1/4”-20 300 (1.33) 150 (.67) 200 (22.6) 2.4 (1.09)

BFV-223 BFV-223WO 5/16”-18 300 (1.33) 150 (.67) 200 (22.6) 2.5 (1.13)

BFV-228 BFV-228WO 3/8”-16 300 (1.33) 150 (.67) 200 (22.6) 2.3 (1.04)

BFV-225 BFV-225WO 1/2”-13 300 (1.33) 150 (.67) 200 (22.6) 2.1 (0.95)

With

Spring

W/O

(Without)

Spring

Channel Nuts

• Design Load Safety Factor of 3

• Overall Nut Height 5/8” (15.9)

• Maximum torque and slip resistance loads shown are when using

stainless steel bolts. When using fiberglass hardware use Max. Torque

for fiberglass bolts, and multiply slip resistance loads by .14 for 3/8”-16

and .60 for 1/2”-13 thread size.

• Material: Glass reinforced polyurethane

• Spring Material: Zinc plated steel

BFVHHCS

Hex Head Cap Screws

• Design Load Safety Factor of 3

• Material: Glass reinforced polyurethane

Design Load

Part No. Thread (in tension) Max. Torque Wt./C

Size Lbs. kN in.-Lbs. N•m Lbs. kg

BFVHHCS 5/16 x 1 5/16”-18 190 (.84) 30 (3.4) .4 (.18)

BFVHHCS 5/16 x 11/4 5/16”-18 190 (.84) 30 (3.4) .5 (.23)

BFVHHCS 5/16 x 11/2 5/16”-18 190 (.84) 30 (3.4) .6 (.27)

BFVHHCS 5/16 x 2 5/16”-18 190 (.84) 30 (3.4) .8 (.36)

BFVHHCS 3/8 x 1 3/8”-16 300 (1.33) 45 (5.1) .9 (.41)

BFVHHCS 3/8 x 11/4 3/8”-16 300 (1.33) 45 (5.1) 1.1 (.50)

BFVHHCS 3/8 x 11/2 3/8”-16 300 (1.33) 45 (5.1) 1.3 (.59)

BFVHHCS 3/8 x 2 3/8”-16 300 (1.33) 45 (5.1) 1.3 (.59)

BFVHHCS 3/8 x 21/2 3/8”-16 300 (1.33) 45 (5.1) 1.5 (.68)

BFVHHCS 1/2 x 1 1/2”-13 490 (2.18) 110 (12.4) 1.4 (.63)

BFVHHCS 1/2 x 11/4 1/2”-13 490 (2.18) 110 (12.4) 1.8 (.81)

BFVHHCS 1/2 x 11/2 1/2”-13 490 (2.18) 110 (12.4) 2.2 (1.00)

BFVHHCS 1/2 x 2 1/2”-13 490 (2.18) 110 (12.4) 3.0 (1.36)

BFVHHCS 1/2 x 21/2 1/2”-13 490 (2.18) 110 (12.4) 3.7 (1.68)

BFVHHCS 1/2 x 3 1/2”-13 490 (2.18) 110 (12.4) 4.5 (2.04)

BFVHN

Hex Nuts

• 3/4” & 1” sizes are available. Contact inside sales for details

• Material: Glass reinforced polyurethane

Part No. Thread Nut Thickness Wt./C

Size in. mm Lbs. kg

BFVHN 5/16 5/16”-18 17/64 (6.7) .2 (.09)

BFVHN 3/8 3/8”-16 21/64 (8.3) .3 (.13)

BFVHN 1/2 1/2”-13 7/16 (11.1) .7 (.32)

BFVHN 5/8 5/8”-11 35/64 (13.9) 1.4 (.63)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

231 B-Line series strut systems Eaton

BFVATRHN

Threaded Rod Nuts

• ATR Nut is required with 3/8”-16 and 1/2”-13 ATR to provide additional

thread engagement which is critical to ATR load carrying capacity.

• Material: Glass reinforced polyurethane

BFVSL Series

Stop-Lock Kits

• Material: Glass Reinforced Polyurethane

Part Thread Wt./C

No. Size Lbs. kg

BFVSL-3/8 3/8”-16 7.4 (3.35)

BFVSL-1/2 1/2”-13 11.3 (5.12)

Part No. Thread H Wt./C

Size in. mm Lbs. kg

BFVATRHN 3/8 3/8”-16 3/4 (19) .8 (.36)

BFVATRHN 1/2 1/2”-13 7/8 (22) 1.7 (.77)

BFVATR

All Threaded Rod

• Design Load Safety Factor of 3

• Design Load can be increased by 40% if a second ATR nut is used.

• Use ATR nuts in place of hex nuts with 3/8”-16 and 1/2”-13 threaded rod in order to obtain

minimum required thread engagement of 17/32” (13.5) to obtain design load shown below.

• Material: Glass reinforced vinyl ester

Design Load Max. Torque Wt./Ft.

Part No. Thread (in tension)

Size Lbs. kN in.-Lbs. N•m Lbs. kg

BFVATR 3/8 x 48” 3/8”-16 350 (1.55) 48 (5.4) .08 (.04)

BFVATR 1/2 x 48” 1/2”-13 650 (2.89) 96 (10.8) .13 (.06)

BFVATR 5/8 x 48” 5/8”-11 1000 (4.45) 192 (21.7) .21 (.09)

BFVFW

Flat Washers

• Material: PVC

Part Hole

No. Size Wt./C

in. Lbs. kg

BFVFW 3/8 3/8 .5 (.22)

BFVFW 1/2 1/2 .5 (.22)

BFVFW 5/8 5/8 .5 (.22)

BFVFW 3/4 3/4 .5 (.22)

BFVFW 1 1 .5 (.22)

H

Fiberglass Materials

BFV655 Series

Rod Couplings

• Material: Glass reinforced polyurethane

Part Thread Wt./C

No. Size Lbs. kg

BFV655-3/8 3/8”-16 7.4 (3.35)

BFV655-1/2 1/2”-13 11.3 (5.12)

BFV655-5/8 5/8”-11 16.7 (7.57)

Reference page 224 for general fitting specifications.

Fiberglass

232 Eaton B-Line series strut systems

Nominal Design Load Maximum

Part No. Pipe Size Torque

in. mm Lbs. kN in.-Lbs. N•m

BFV2008 1/2 (15) 300 (1.33) 10 (1.13)

BFV2009 3/4 (20) 300 (1.33) 10 (1.13)

BFV2010 1 (25) 300 (1.33) 10 (1.13)

BFV2011 11/4 (32) 300 (1.33) 10 (1.13)

BFV2012 11/2 (40) 300 (1.33) 10 (1.13)

BFV2013 2 (50) 300 (1.33) 10 (1.13)

BFV2014 21/2 (65) 300 (1.33) 10 (1.13)

BFV2015 3 (80) 300 (1.33) 10 (1.13)

BFV2016 31/2 (90) 300 (1.33) 10 (1.13)

BFV2017 4 (100) 300 (1.33) 10 (1.13)

BFV2000 Series

Non-Metallic Pipe Clamps

• For rigid and PVC conduit.

• Standard hardware includes slotted round head machine

screw and square nut in 316 stainless steel

• Design Load Safety Factor of 3

• Material: Glass reinforced PPO

• Not recommended for vertical installation without additional Stop-Lock

Kit. Kit includes one square washer, channel nut and hex head cap screw.

Order (Stop-Lock Kit on page 232) BFVSL-3/8 for 3/8”-16 hardware or

BFVSL-1/2 for 1/2”-13 hardware. Mount kit below clamp when used

in vertical strut to prevent clamp slipping.

• If non-metallic hardware is required, add N to the part number.

Example: BFV2008N

BFV100 thru BFV300

Adjustable Pipe Clamps

• Completely Non-Metallic

• Adjustable to U.S. & Metric pipe diameters

• Fits OD Sizes 3/4” (19.0) to 31/2” (88.9)

• Easy To Install

• No special tools required

• Design Load Safety Factor of 3

• Material: Glass reinforced polyurethane

• Not recommended for vertical installation without additional

Stop-Lock Kit. Kit includes one square washer, channel nut

and hex head cap screw.

Order (Stop-Lock Kit on page 232) BFVSL-3/8 for 3/8”-16

hardware or BFVSL-1/2 for 1/2”-13 hardware.

Mount kit below clamp when used in vertical strut to

prevent clamp slipping.

Nominal Pipe O.D. Design Max.

Part No. Pipe Sizes Range Load Torque

in. mm in. mm Lbs. kN in.-Lbs. N•m

BFV100 1/2 - 11/2 (15- 40) .75 - 1.90 (21.3 - 48.3) 135 (.60) 10 (1.13)

BFV200 11/2 - 2 (40 - 51) 1.90 - 2.37 (48.3 - 60.3) 135 (.60) 36 (4.07)

BFV300 21/2 - 3 (63 - 76) 2.87 - 3.50 (73.0 - 88.9) 145 (.64) 36 (4.07)

Design Load

Design Load

Stop-Lock Kit

for vertical

installation

Stop-Lock Kit

for vertical

installation Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

233 B-Line series strut systems Eaton

BFP2400 Series

2-Hole Pipe Clamps

• Design Load Safety Factor of 3

• Material: Glass reinforced polyester

BFV751 & BFV751J

Beam Clamp

• Design Load Safety Factor of 3

• BFV751J (clip included) must be used when installed on

tapered flange beams.

• Material: Glass reinforced polyurethane

• Setscrew material: Stainless Steel 316 ASTM F593 Group 2, S4

Part No. For Hanger Rod Design Load Torque

Size A Lbs. kN ft.-Lbs. N•m

BFV751-3/8 3/8”-16 500 (2.22) 10 (13)

BFV751J-3/8 3/8”-16 500 (2.22) 10 (13)

BFV751-1/2 1/2”-13 500 (2.22) 10 (13)

BFV751J-1/2 1/2”-13 500 (2.22) 10 (13)

BFV751-5/8 5/8”-11 500 (2.22) 10 (13)

BFV751J-5/8 5/8”-11 500 (2.22) 10 (13)

41/4”

(108.0)

11/8”

(28.6)

1”

(25.4)

1/2”-13 x 2” (50.8)

Screw

Tapped for

Hanger Rod

Size A

BFV751

(Clamp

Only)

BFV751J

(Clamp and

Retainer Clip)

BFVATR3/8”

& BFVATRHN

(Order Separately)

see page 232

3”

(76.2)

Nominal Design

Part Pipe A B Load

No. Size

in. mm in. mm in. mm Lbs. kN

BFP2400-2 2 (50) 23/8 (60) 51/2 (140) 115 (0.51)

BFP2400-3 3 (80) 31/2 (89) 63/4 (171) 130 (0.58)

BFP2400-4 4 (100) 41/2 (114) 73/4 (197) 150 (0.66)

BFP2400-6 6 (150) 65/8 (168) 10 (254) 150 (0.66)

15/8”

(41.3)

13/32” (10.3)

Hole Dia.

B

Pipe

Size

Design Load

A Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

234 Eaton B-Line series strut systems

BFV3104 Series

Clevis Hangers

• Design Load Safety Factor of 3 at 120°F (49°C).

• Insulation may be required at higher temperatures.

• Order hanger rod and nuts separately.

• Material: Glass reinforced polyurethane for BFV3104-1 thru BFV3104-6

• Material: Glass reinforced polyester & vinyl ester for BFV3104-8 thru BFV3104-12

Nominal Hanger Design

Part No. Pipe A BC Rod Load

Size Size

in. mm in. mm in. mm in. mm Lbs. kN

BFV3104-1 1 (50) 11/2 (38) 41/4 (108) 11/4 (32) 1/2”-13 670 (2.98)

BFV3104-11/2 11/2 (65) 2 (51) 51/8 (130) 11/4 (32) 1/2”-13 670 (2.98)

BFV3104-2 2 (50) 21/2 (63) 61/2 (165) 11/4 (32) 1/2”-13 730 (3.25)

BFV3104-21/2, 3, 4 21/2-4 (65-100) 51/8 (130) 10 (254) 11/2 (38) 1/2”-13 1150 (5.11)

BFV3104-6 6 (150) 63/4 (171) 125/16 (313) 2 (51) 1/2”-13 1170 (5.20)

Nominal Hanger Design

Part No. Pipe AB C Rod Load

Size Size

in. mm in. mm in. mm in. mm Lbs. kN

BF*3104-8 8 (200) 91/4 (235) 165/8 (422) 3 (76) 5/8”-11 350 (1.55)

BF*3104-10 10 (250) 113/8 (289) 197/8 (505) 4 (101) 5/8”-11 450 (2.01)

BF*3104-12 12 (300) 131/2 (343) 223/8 (568) 5 (127) 5/8”-11 600 (2.69)

BFV3104-1 thru BFV3104-6 BFV3104-8 thru BFV3104-12

A A

B

B

C

C

BFV755

Beam Clamp

• Design Load Safety Factor of 3

• Material: Glass reinforced polyurethane

• Setscrew material: Stainless Steel 316 ASTM F593 Group 2, S4

Part No. For Hanger Rod Design Load Torque

Size A Lbs. kN ft.-Lbs. N•m

BFV755-3/8 3/8”-16 400 (1.78) 10 (13)

BFV755-1/2 1/2”-13 400 (1.78) 10 (13)

3”

(76.2)

3/4”

(19.0)

Tapped for

Hanger Rod

Size A

25/8”

(66.7)

1/2”-13 x 2” (50.8)

Screw

*Specify P for polyester or V for Vinyl ester.

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

235 B-Line series strut systems Eaton

BF*494 Series

Brackets 24” (609mm) to 36” (914mm) Long

• Design Load Safety Factor of 3 based on uniform loading

• MH1 - From top of bracket to center of mounting hole

• MH2 - From bottom of bracket to center of mounting hole

• Material: Glass reinforced vinyl ester or polyester

Design

Part No. A B Load

in. mm in. mm Lbs. kN

BF*494-24 28 (711) 23 (584) 750 (3.33)

BF*494-30 34 (863) 26 (660) 750 (3.33)

BF*494-36 40 (1016) 29 (736) 750 (3.33)

* Insert P for glass reinforced polyester resin or

V for glass reinforced vinyl ester resin

BF*409 Series

Brackets 6” (152mm) to 24” (609mm) Long

• Design Load Safety Factor of 3 based on uniform loading

• MH1 - From top of bracket to center of mounting hole

• MH2 - From bottom of bracket to center of mounting hole

Design

Part No. A Load

in. mm Lbs. kN

BF*409-6 10 (250) 1400 (6.22)

BF*409-9 13 (330) 1000 (4.45)

BF*409-12 16 (406) 800 (3.56)

BF*409-18 22 (559) 675 (3.00)

BF*409-24 28 (711) 450 (2.00)

* Insert P for Glass Reinforced Polyester Resin or

V for Glass Reinforced Vinyl Ester Resin

A

A

B

13/32” (10.3) Dia.

Mounting Holes

13/32” (10.3) Dia.

Mounting Holes

11/4” (31.7)

To Hole

11/4” (31.7)

To Hole

11/4” (31.7)

To Hole

11/4” (31.7)

To Hole

12”

(304.8) Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

236 Eaton B-Line series strut systems

BFV201

Square Washer for 3/8” bolt

• Material: Injection molded glass reinforced polyurethane

BFV202

Square Washer for 1/2” bolt

• Material: Injection molded glass reinforced polyurethane

BFV141

Three Hole Flat Plate

• Material: Injection molded glass reinforced polyurethane

BFV340

Two Hole Flat Plate

• Material: Injection molded glass reinforced polyurethane

BFV129

Two Hole Splice Plate

• Material: Injection molded glass reinforced polyurethane

BFV557

Three Hole Flat Plate

• Material: Injection molded glass reinforced polyurethane

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3)

15/8”

(41.3)

13/32” (10.3)

Diameter Hole

9/16” (14.3)

Diameter Hole

31/2”

(88.9)

31/4”

(82.5)

53/8”

(136.5)

47/8”

(123.8)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

237 B-Line series strut systems Eaton

BFV341

Four Hole Splice Plate

• Material: Injection molded glass reinforced polyurethane

BFV342

Five Hole Flat Plate

• Material: Injection molded glass reinforced polyurethane

BFV132

Five Hole Flat Cross Plate

• Material: Injection molded glass reinforced polyurethane

BFV140

Three Hole Flat Corner Plate

• Material: Injection molded glass reinforced polyurethane

BFV143

Four Hole Flat Corner Plate

• Material: Injection molded glass reinforced polyurethane

BFV133

Four Hole Flat Tee Plate

• Material: Injection molded glass reinforced polyurethane

31/2”

(88.9)

31/2”

(88.9)

53/8”

(136.5)

53/8”

(136.5)

53/8”

(136.5) 53/8”

(136.5)

71/4”

(184.1)

91/8”

(231.8)

31/2”

(88.9)

31/2”

(88.9)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

238 Eaton B-Line series strut systems

BFV135

Three Hole Flat Gusset Corner Plate

• Material: Injection molded glass reinforced polyurethane

BFV142

Four Hole Flat Gusset Corner Plate

• Material: Injection molded glass reinforced polyurethane

BFV532

Five Hole Flat Gusset Tee Plate

• Material: Injection molded glass reinforced polyurethane

BFV337

Three Hole Flat Gusset Tee Plate

• Material: Injection molded glass reinforced polyurethane

BFV136

Four Hole Flat Gusset Tee Plate

• Material: Injection molded glass reinforced polyurethane

BFV334

Seven Hole Flat Gusset Cross Plate

• Material: Injection molded glass reinforced polyurethane

31/2”

(88.9)

31/2”

(88.9)

31/2”

(88.9)

31/2”

(88.9)

31/2”

(88.9)

31/2”

(88.9)

53/8”

(136.5)

53/8”

(136.5)

53/8”

(136.5)

53/8”

(136.5)

91/8”

(231.8)

53/8”

(136.5)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

239 B-Line series strut systems Eaton

31/2”

(88.9)

31/2”

(88.9)

41/8”

(104.8) 41/8”

(104.8)

BFV101

Two Hole 90° Corner Angle

• Material: Injection molded glass reinforced polyurethane

BFV103

Three Hole 90° Corner Angle

• Material: Injection molded glass reinforced polyurethane

BFV558

Four Hole 90° Corner Angle

• Material: Injection molded glass reinforced polyurethane

BFV104

Four Hole 90° Corner Angle

• Material: Injection molded glass reinforced polyurethane

BFV118

Four Hole 90° Gussetted Shelf Angle

• Material: Injection molded glass reinforced polyurethane

BFV371-2G

Three Hole 90° Gussetted Corner Angle

• Material: Injection molded glass reinforced polyurethane

31/4”

(82.5)

15/8”

(41.3) 15/8”

(41.3)

4”

(101.6)

Three Holes

.400” Dia. (10.1)

21/4”

(57.1)

15/8”

(41.3)

15/8”

(41.3)

41/8”

(104.8)

25/16”

(58.7)

15/8”

15/8” (41.3)

(41.3)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

240 Eaton B-Line series strut systems

BFV280SQ

Post Base for BF*22

• Material: Glass reinforced polyurethane

BFV281SQ

Post Base for BF*22A

• Material: Glass reinforced polyurethane

BFV650

Channel Spacer

• Spacer I.D. accommodates 3/8\" rod or bolts.

• Material: Polyurethane

B217P

Plastic Closure Strip

• Available in 10 Ft. (3.05 m) lengths.

• Material: PVC

17/16”

(36.5)

5”

(127.0)

5”

(127.0)

5”

(127.0)

3”

(76.3)

3”

(76.3)

Used when attaching fittings to side walls of

channel. This channel spacer prevents wall

compression in heavy load conditions.

65/8”

(168.3)

5/8”

(15.9)

Fiberglass Materials

Reference page 224 for general fitting specifications.

Fiberglass

241 B-Line series strut systems Eaton

Our mini channels and fittings provide for an economical method of supporting light load requirements on a strut

system.

Channel

Channels are cold formed on our modern rolling mills from 18 Ga. (1.2 mm) low carbon steel strips plain steel

(ASTM A1008 33,000 PSI min. yield) and pre-galvanized steel strips, (ASTM A653 33,000 PSI min. yield). A

continuous slot with inturned lips provides the ability to make attachments at any point. Channel combinations

are made with new state of the art, high-tech welding equipment.

Lengths

Standard lengths are 10’ (3.05 m) and 20’ (6.09 m) for B62 series, and 10’ (3.05 m) for B72 series. Custom lengths

are available.

Fittings

Mini fittings are formed from hot rolled pickled and oiled strip or sheet steel (ASTM A1011, HSLAS, Grade 50,

Class1). The following dimensions apply to all fittings except as noted on the drawings:

Hole Size – 9/32” (7.14 mm) Dia.

Hole Spacing – 13/32” (10.3 mm) from end and 11/16” (27.0 mm) on center.

Width – 13/16” (20.6 mm)

Thickness – 1/8” (3.2 mm)

Materials & Finishes*

*Unless otherwise noted.

Metric

Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters.

Mini Channel & Fittings

Mini Channel & Fittings

242

Finish

Code Finish Specification

PLN Plain ASTM A1011, HSLAS,

Grade 50, Class 1

ZN Electro-Plated Zinc ASTM B633 SC3 Type II

GRN DURA-GREEN™

GLV Pre-Galvanized ASTM A653

33,000 PSI min. yield

HDG Hot-Dipped Galvanized ASTM A123

Eaton B-Line series strut systems

• Thickness: 18 Ga. (1.2 mm)

• Standard lengths: 10’ (3.05 m) & 20’ (6.09 m)

• Standard finishes: Plain, DURA GREEN™,

Pre-Galvanized

• Weight: .42 Lbs./Ft. (.62 kg/m)

13/16”

(20.6)

13/16”

(20.6)

13/16”

(20.6)

7/16”

(11.1)

13/16”

(20.6)

.406

(10.3)

.406

(10.3)

.346

(8.8)

3/16”

(4.7) 3/32”

(2.4)

3/16”

(4.7) 15/8”

(41.3)

Y

X

X

Y

B62A

Wt. .84 Lbs./Ft. (1.25 kg/m)

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

B62 Channel

243

Areas of Momentof Section Radius of Moment of Section Radius of

Channel Weight Section Inertia (I) Modulus (S) Gyration (r) Inertia (I) Modulus (S) Gyration (r)

lbs./ft. kg/m sq. in. cm2 in.4 cm4 in.3 cm3 in. cm in.4 cm4 in.3 cm3 in. cm

B62 .420 (.62) .123 (.80) .0103 (.43) .0221 (.36) .289 (.73) .0134 (.56) .0330 (.54) .330 (.84)

B62A .839 (1.25) .247 (1.59) .0500 (2.08) .0616 (1.01) .450 (1.14) .0269 (1.12) .0663 (1.09) .330 (.84)

X - X Axis Y - Y Axis

Calculations of section properties are based on metal thicknesses as determined by the AISI Cold-Formed Steel Design Manual.

Section Properties

Beam Loading

Based on simple beam condition using an allowable design stress of 25,000 psi (172 MPa) in accordance with MFMA, with adequate lateral

bracing (see page 12 for further explanation). Actual yield point of cold rolled steel is 42,000 psi. To determine concentrated load capacity at

mid span, multiply uniform load by 0.5 and corresponding deflection by 0.8. *Failure determined by weld shear.

Uniform Load @ Deflection =

Beam Span Channel Uniform Load and Deflection 1/240 Span 1/360 Span

In. mm Style Lbs. kN In. mm Lbs. kN Lbs. kN

12 (305) B62 364 (1.62) .027 (.68) 364 (1.62) 364 (1.62)

B62A 420* (1.87) .006 (.15) 420* (1.87) 420* (1.87)

24 (609) B62 182 (0.81) .109 (2.77) 167 (0.74) 111 (0.49)

B62A 420* (1.87) .051 (1.29) 420* (1.87) 420* (1.87)

36 (914) B62 121 (0.54) .245 (6.22) 74 (0.33) 50 (0.22)

B62A 341 (1.51) .141 (3.58) 341 (1.51) 242 (1.07)

48 (1219) B62 91 (0.40) .436 (11.07) 42 (0.18) 28 (0.12)

B62A 256 (1.14) .250 (6.35) 204 (0.91) 136 (0.60)

60 (1524) B62 73 (0.32) .681 (17.30) 27 (0.12) 18 (0.08)

B62A 205 (0.91) .391 (9.93) 131 (0.58) 87 (0.39)

72 (1829) B62 61 (0.27) .981 (24.92) 19 (0.08) 12 (0.05)

B62A 170 (0.75) .563 (14.30) 91 (0.40) 61 (0.27)

**Where the slenderness ratio KL exceeds 200, and K = end fixity factor, L = actual length and r = radius of gyration. r

Column Loading

Max. Column Loading K = .80 Max. Column Loading (Loaded @ C.G.)

Unbraced Channel Loaded@ Loaded@

Height Style C.G. Slot Face K = .65 K = 1.0 K = 1.2

In. mm Lbs. kN Lbs. kN Lbs. kN Lbs. kN Lbs. kN

12 (305) B62 2052 (9.13) 820 (3.65) 2161 (9.61) 1890 (8.41) 1715 (7.63)

B62A 4666 (20.75) 1449 (6.44) 4710 (20.95) 4593 (20.43) 4503 (20.03)

24 (609) B62 1350 (6.00) 645 (2.87) 1624 (7.22) 1020 (4.54) 818 (3.64)

B62A 4275 (19.01) 1367 (6.08) 4453 (19.81) 3982 (17.71) 3624 (16.12)

36 (914) B62 818 (3.64) 471 (2.09) 1053 (4.68) 633 (2.81) 515 (2.29)

B62A 3624 (16.12) 847 (3.77) 4023 (17.89) 2965 (13.19) 2179 (9.69)

48 (1219) B62 589 (2.62) 369 (1.64) 745 (3.31) 456 (2.03) 365** (1.62)

B62A 2713 (12.06) 504 (2.24) 3421 (15.21) 1765 (7.85) 1225 (5.45)

60 (1524) B62 456 (2.03) 300 (1.33) 579 (2.57) 347** (1.54) 271** (1.20)

B62A 1765 (7.85) 323 (1.44) 2647 (11.77) 1129 (5.02) 784** (3.49)

72 (1829) B62 365** (1.62) 248 (1.10) 470 (2.09) 271** (1.20) – –

B62A 1225 (5.45) 224 (0.99) 1856 (8.25) 784** (3.49) 545** (2.42)

B-Line series strut systems Eaton

• Thickness: 18 Ga. (1.2 mm)

• Standard lengths: 10’ (3.05 m) & 20’ (6.09 m)

• Standard finishes: Plain, DURA GREEN™,

Pre-Galvanized

• Weight: .29 Lbs./Ft. (.43 kg/m)

B72A

Wt. .58 Lbs./Ft. (.87 kg/m)

13/16”

(20.6)

7/16”

(11.1)

.406

(10.3)

.160

(4.0)

3/32”

(2.4)

3/16”

(4.7)

3/16”

(4.7)

13/32”

(10.3)

13/16”

(20.6)

13/16”

(20.6)

.406

(10.3)

.406

(10.3)

Y

Y

X

X

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

B72 Channel

244

Areas of Momentof Section Radius of Moment of Section Radius of

Channel Weight Section Inertia (I) Modulus (S) Gyration (r) Inertia (I) Modulus (S) Gyration (r)

lbs./ft. kg/m sq. in. cm2 in.4 cm4 in.3 cm3 in. cm in.4 cm4 in.3 cm3 in. cm

B72 .287 (.43) .084 (.54) .0018 (.07) .0073 (.12) .146 (.37) .0077 (.32) .0190 (.31) .302 (.77)

B72A .574 (.85) .169 (1.09) .0078 (.32) .0192 (.31) .215 (.55) .0155 (.65) .0382 (.63) .303 (.77)

X - X Axis Y - Y Axis

Calculations of section properties are based on metal thicknesses as determined by the AISI Cold-Formed Steel Design Manual.

Section Properties

Beam Loading

Based on simple beam condition using an allowable design stress of 25,000 psi (172 MPa) in accordance with MFMA, with adequate lateral

bracing (see page 12 for further explanation). Actual yield point of cold rolled steel is 42,000 psi. To determine concentrated load capacity at

mid span, multiply uniform load by 0.5 and corresponding deflection by 0.8. *Failure determined by weld shear.

Uniform Load @ Deflection =

Beam Span Channel Uniform Load and Deflection 1/240 Span 1/360 Span

In. mm Style Lbs. kN In. mm Lbs. kN Lbs. kN

12 (305) B72 116 (0.51) .051 (1.29) 113 (0.50) 75 (0.32)

B72A 210* (0.93) .020 (.51) 210* (0.93) 210* (0.93)

24 (609) B72 58 (0.26) .206 (5.23) 28 (0.12) 19 (0.08)

B72A 159 (0.71) .125 (3.17) 127 (0.56) 85 (0.38)

36 (914) B72 39 (0.17) .465 (11.81) 13 (0.06) 8 (0.03)

B72A 106 (0.45) .281 (7.14) 57 (0.25) 38 (0.17)

36 (1219) B72 29 (0.13) .827 (21.00) 7 (0.03) 5 (0.02)

B72A 80 (0.35) .500 (12.70) 32 (0.14) 21 (0.09)

60 (1524) B72 23 (0.10) 1.292 (32.81) 5 (0.02) 3 (0.01)

B72A 64 (0.28) .782 (19.86) 20 (0.09) 14 (0.06)

**Where the slenderness ratio KL exceeds 200, and K = end fixity factor, L = actual length and r = radius of gyration. r

Column Loading

Max. Column Loading K = .80 Max. Column Loading (Loaded @ C.G.)

Unbraced Channel Loaded@ Loaded@

Height Style C.G. Slot Face K = .65 K = 1.0 K = 1.2

In. mm Lbs. kN Lbs. kN Lbs. kN Lbs. kN Lbs. kN

12 (305) B72 1598 (7.11) 539 (2.40) 1712 (7.61) 1410 (6.27) 1181 (5.25)

B72A 3600 (16.01) 986 (4.38) 3700 (16.46) 3433 (15.27) 3229 (14.36)

24 (609) B72 701 (3.12) 320 (1.42) 1050 (4.67) 450 (2.00) 313** (1.39)

B72A 2710 (12.05) 802 (3.57) 3113 (13.85) 2043 (9.09) 1421 (6.32)

36 (914) B72 313** (1.39) 188 (0.83) 473 (2.10) 201** (0.89) – – B72A 1421 (6.32) 569 (2.53) 2135 (9.50) 909 (4.04) 631** (2.81)

36 (1219) B72 177** (0.79) 122 (0.54) 267** (1.19) – – ––

B72A 799 (3.55) 404 (1.80) 1211 (5.39) 512** (2.28) 355** (1.58)

60 (1524) B72 113** (0.50) 85 (0.38) 171** (0.76) – – –– B72A 512** (2.28) 298 (1.32) 775 (3.45) 327** (1.45) – –

Eaton B-Line series strut systems

Part Number

B62 B72

With Without With Without Thread Thickness Wt./C

Spring Spring Spring Spring Size In. mm Lbs. kg

N621 N621WO N7221 N621WO #8-32 .150 (3.81) 1.0 (.45)

N622 N622WO N7222 N622WO #10-24 .150 (3.81) 1.0 (.45)

N627 N627WO N7227 N627WO #10-32 .150 (3.81) 1.0 (.45)

N624 N624WO N7224 N624WO 1/4-20 .150 (3.81) 1.0 (.45)

BMM-3L BMM-3 BMM-3S BMM-3 M3.5 x 0.6 .150 (3.81) 1.0 (.45)

BMM-4L BMM-4 BMM-4S BMM-4 M4 x 0.7 .150 (3.81) 1.0 (.45)

BMM-5L BMM-5 BMM-5S BMM-5 M5 x 0.8 .150 (3.81) 1.0 (.45)

BMM-6L BMM-6 BMM-6S BMM-6 M6 x 1 .150 (3.81) 1.0 (.45)

Nuts for B62, B72 Channel

Mini Fittings

Spring Nut Nut Without Spring

B6202

Square Washer

• Standard finishes: ZN, GRN

• Wt./C 2 Lbs. (.9 kg)

B6129

Two Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 5 Lbs. (2.2 kg)

B6340

Two Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 5 Lbs. (2.2 kg)

13/16”

(20.6)

13/16”

(20.6)

17/8”

(47.6)

15/8”

(41.3)

9/32” (7.1)

DIA.

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

Mini Channel Nuts & Fittings

245 B-Line series strut systems Eaton

B6557

Three Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 7 Lbs. (3.2 kg)

B600-62

Three Hole Flat Adapter Plate

• Standard finishes: ZN, GRN

• Wt./C 19 Lbs. (8.6 kg)

B6141

Three Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 7 Lbs. (3.2 kg)

B6341

Four Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 11 Lbs. (5.0 kg)

B6138

Two Hole Swivel Plate

• Standard finishes: ZN, GRN

• Wt./C 7 Lbs. (3.2 kg)

B6139

Three Hole Swivel Plate

• Standard finishes: ZN, GRN

• Wt./C 10 Lbs. (4.5 kg)

B6504

Four Hole Splice Plate

• Standard finishes: ZN, GRN

• Wt./C 10 Lbs. (4.5 kg)

B6140

Three Hole Corner Plate

• Standard finishes: ZN, GRN

• Wt./C 8 Lbs. (3.6 kg)

B6143

Four Hole Corner Plate

• Standard finishes: ZN, GRN

• Wt./C 11 Lbs. (5.0 kg)

215/16”

(74.6) 15/8”

(41.3)

4”

(101.6)

13/16”

(20.6)

41/8” (104.8)

211/16”

(68.2)

17/8”

(47.6)

27/16”

(61.9)

33/4”

(95.2)

B62

B22

13/16”

(20.6)

17/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6) 15/8”

(41.3)

17/8”

(47.6)

215/16”

(74.6)

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

Mini Fittings

246 Eaton B-Line series strut systems

B6135

Three Hole Corner Gusset Plate

• Standard finishes: ZN, GRN

• Wt./C 9 Lbs. (4.1 kg)

B6132

Five Hole Cross Plate

• Standard finishes: ZN, GRN

• Wt./C 13 Lbs. (5.9 kg)

B6133

Four Hole Tee Plate

• Standard finishes: ZN, GRN

• Wt./C 11 Lbs. (5.0 kg)

B6142

Four Hole Corner Gusset Plate

• Standard finishes: ZN, GRN

• Wt./C 15 Lbs. (6.8 kg)

B6337

Three Hole Tee Gusset Plate

• Standard finishes: ZN, GRN

• Wt./C 10 Lbs. (4.5 kg)

B6136

Four Hole Tee Gusset Plate

• Standard finishes: ZN, GRN

• Wt./C 15 Lbs. (6.8 kg)

B6532

Five Hole Tee Gusset Plate

• Standard finishes: ZN, GRN

• Wt./C 22 Lbs. (10.0 kg)

B6101

Two Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 5 Lbs. (2.2 kg)

B6230

Two Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 5 Lbs. (2.2 kg)

11/4”

(31.7)

11/8”

(28.6)

215/16”

(74.6)

215/16”

(74.6)

215/16”

(74.6)

17/8”

(47.6)

215/16”

(74.6)

17/8”

(47.6)

215/16”

(74.6)

215/16”

(74.6)

215/16”

(74.6)

17/8”

1 (47.6) 7/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6)

13/16”

(20.6)

15/16”

(23.8)

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

Mini Fittings

247 B-Line series strut systems Eaton

B6232

Three Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 7 Lbs. (3.2 kg)

B6103

Three Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 8 Lbs. (3.6 kg)

B6102

Three Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 8 Lbs. (3.6 kg)

B6374

Three Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 7 Lbs. (3.2 kg)

B6104

Four Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 10 Lbs. (4.5 kg)

B6558

Four Hole Corner Angle

• Standard finishes: ZN, GRN

• Wt./C 10 Lbs. (4.5 kg)

B6357

Four Hole Offset Bent Tee

• Standard finishes: ZN, GRN

• Wt./C 11 Lbs. (5.0 kg)

B6239

Five Hole Offset Bent Tee

• Standard finishes: ZN, GRN

• Wt./C 14 Lbs. (6.3 kg)

B6144R & L

Four Hole Shelf Bracket

• Standard finishes: ZN, GRN

• Wt./C 19 Lbs. (8.6 kg)

2”

(50.8)

13/16”

(20.6)

13/16”

(20.6)

23/16”

(55.5)

15/16”

(23.8)

13/16”

(20.6)

17/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6)

17/8”

(47.6)

25/16”

(58.7)

25/16”

(58.7)

25/16”

(58.7)

11/4”

(31.7)

11/4”

(31.7)

11/8”

(28.6)

15/8”

(41.3)

11/8”

(28.6)

11/8”

(28.6)

215/16”

(74.6)

215/16”

(74.6)

15/16”

(23.8)

(Right shown)

Mini Channel & Fittings

Reference page 242 for general fitting specifications.

Mini Fittings

248 Eaton B-Line series strut systems