该页无缩略图
直槽 Straight FluteJIS 日标高性能丝锥系列 C/2-3PJIS Standard High-Performance HSSE-PM Tap
| 型号 Model 涂层 Coated | 库存 Śtock | 尺寸 Dimension/mm | ||||||||
| TP | LU | CZCMS | TCTR | DCONMS | TD | LF | THL | |||
| JHTM2-6HXCCP | 0.4 | 16 | 3x2.5 | 6HX | 3 | 2 | 40 | 6 | ||
| JHTM2.5-6HXCCP | 0.45 | 16 | 3x2.5 | 6HX | 3 | 2.5 | 44 | 6.5 | ||
| JHTM3-6HXCCP | 0.5 | 19 | 4x3.2 | 6HX | 4 | 3 | 46 | 7.5 | ||
| JHTM4-6HXCCP | 0.7 | 21 | 5x4 | 6HX | 5 | 4 | 52 | 10.5 | ||
| JHTM5-6HXCCP | 0.8 | 24 | 5.5x4.5 | 6HX | 5.5 | 5 | 60 | 12 | ||
| JHTM6-6HXCCP | 1.0 | 29 | 6x4.5 | 6HX | 6 | 6 | 62 | 15 | ||
| JHTM8-6HXCCP | 1.25 | 37 | 6.2x5 | 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM10-6HXCCP | 1.5 | 41 | 7x5.5 | 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM12-6HXCCP | 1.75 | 48 | 8.5x6.5 | 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM14-6HXCCP | 2.0 | 48 | 10.5x8 | 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM16-6HXCCP | 2.0 | 52 | 12.5x10 | 6HX | 12.5 | 16 | 95 | 30 | ||
| JHTM18-6HXCCP | 2.5 | 55 | 14x11 | 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM20-6HXCCP | 2.5 | 58 | 15x12 | 6HX | 15 | 20 | 105 | 37.5 | ||
| JHTM3×0.35-6HXCCP | 0.35 | 19 | 4x3.2 | 6HX | 4 | 3 | 46 | 7.5 | ||
| JHTM4×0.5-6HXCCP | 0.5 | 21 | 5x4 | 6HX | 5 | 4 | 52 | 10.5 | ||
| JHTM5×0.5-6HXCCP | 0.5 | 24 | 5.5x4.5 | 6HX | 5.5 | 5 | 60 | 12 | ||
| JHTM6×0.5-6HXCCP | 0.5 | 29 | 6x4.5 | 6HX | 6 | 6 | 62 | 15 | ||
| JHTM6×0.75-6HXCCP | 0.75 | 29 | 6x4.5 | 6HX | 6 | 6 | 62 | 15 | ||
| JHTM8×0.75-6HXCCP | 0.75 | 37 | 6.2x5 | 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM8×1-6HXCCP | 1.0 | 37 | 6.2x5 | 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM10×1-6HXCCP | 1.0 | 41 | 7x5.5 | 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM10×1.25-6HXCCP | 1.25 | 41 | 7x5.5 | 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM12×1-6HXCCP | 1.0 | 48 | 8.5x6.5 | 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM12×1.25-6HXCCP | 1.25 | 48 | 8.5x6.5 | 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM12×1.5-6HXCCP | 1.5 | 48 | 8.5x6.5 | 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM14×1-6HXCCP | 1.0 | 48 | 10.5x8 | 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM14×1.25-6HXCCP | 1.25 | 48 | 10.5x8 | 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM14×1.5-6HXCCP | 1.5 | 48 | 10.5x8 | 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM16×1-6HXCCP | 1.0 | 52 | 12.5x10 | 6HX | 12.5 | 16 | 95 | 30 | ||
| JHTM16×1.5-6HXCCP | 1.5 | 52 | 12.5x10 | 6HX | 12.5 | 16 | 95 | 30 | ||
| JHTM18×1-6HXCCP | 1.0 | 55 | 14x11 | 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM18×1.5-6HXCCP | 1.5 | 55 | 14x11 | 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM18×2-6HXCCP | 2.0 | 55 | 14x11 | 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM20×1-6HXCCP | 1.0 | 58 | 15x12 | 6HX | 15 | 20 | 105 | 37.5 | ||
| JHTM20×1.5-6HXCCP | 1.5 | 58 | 15x12 | 6HX | 15 | 20 | 105 | 37.5 | ||
| JHTM20×2-6HXCCP | 2.0 | 58 | 15x12 | 6HX | 15 | 20 | 105 | 37.5 | ||
●标准库存 ○订单生产
切削材料推荐 Cutting material recommendation
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
直槽 Straight Flute
JIS 日标高性能丝锥系列 E/1.5-2PJIS Standard High-Performance HSSE-PM Tap
切削材料推荐 Cutting material recommendation
| 型号 Model 涂层 Coated | 库存 Śtock | 尺寸 Dimension/mm | ||||||||
| TDZ TP | LU | CZCMS | TCTR | DCONMS | TD | LF | THL | |||
| JHTM2-6HXECP | M2 0.4 | 16 | 3x2.5 | 6HX | 3 | 2 | 40 | 6 | ||
| JHTM2.5-6HXECP | M2.5 | 0.45 | 16 3x2.5 | 6HX | 3 | 2.5 | 44 | 6.5 | ||
| JHTM3-6HXECP | M3 | 0.5 19 | 4x3.2 | 6HX | 4 | 3 | 46 | 7.5 | ||
| JHTM4-6HXECP | M4 | 0.7 21 | 5x4 | 6HX | 5 | 4 | 52 | 10.5 | ||
| JHTM5-6HXECP | M5 | 0.8 | 24 5.5x4.5 | 6HX | 5.5 | 5 | 60 | 12 | ||
| JHTM6-6HXECP | M6 | 1.0 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 15 | ||
| JHTM8-6HXECP | M8 | 1.25 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM10-6HXECP | M10 | 1.5 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM12-6HXECP | M12 | 1.75 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM14-6HXECP | M14 | 2.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM16-6HXECP | M16 | 2.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 30 | ||
| JHTM18-6HXECP | M18 | 2.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM20-6HXECP | M20 | 2.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 37.5 | ||
| JHTM3×0.35-6HXECP | M3x0.35 | 0.35 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 7.5 | ||
| JHTM4×0.5-6HXECP | M4x0.5 | 0.5 | 21 | 5x4 6HX | 5 | 4 | 52 | 10.5 | ||
| JHTM5×0.5-6HXECP | M5x0.5 | 0.5 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 12 | ||
| JHTM6×0.5-6HXECP | M6x0.5 | 0.5 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 15 | ||
| JHTM6×0.75-6HXECP | M6x0.75 | 0.75 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 15 | ||
| JHTM8×0.75-6HXECP | M8x0.75 | 0.75 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM8×1-6HXECP | M8x1 | 1.0 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 18.8 | ||
| JHTM10×1-6HXECP | M10x1 | 1.0 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM10×1.25-6HXECP | M10x1.25 | 1.25 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 22.5 | ||
| JHTM12×1-6HXECP | M12x1 | 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM12×1.25-6HXECP | M12x1.25 | 1.25 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM12×1.5-6HXECP | M12x1.5 | 1.5 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 26.3 | ||
| JHTM14×1-6HXECP | M14x1 | 1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 30 | ||
| JHTM14×1.25-6HXECP | M14x1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 30 | |||
| JHTM14×1.5-6HXECP | M14x1.5 | 1.5 | 48 | 10.5x8 6HX 12.5x10 | 10.5 | 14 | 88 | 30 | ||
| JHTM16×1-6HXECP | M16x1 | 1.0 | 52 | 6HX | 12.5 | 16 | 95 | 30 | ||
| JHTM16×1.5-6HXECP | M16x1.5 | 1.5 1.0 | 52 55 | 12.5x10 6HX 6HX | 12.5 14 | 16 18 | 95 | 30 | ||
| JHTM18×1-6HXECP | M18x1 | 1.5 | 14x11 14x11 6HX | 14 | 18 | 100 | 37.5 | |||
| JHTM18×1.5-6HXECP | M18x1.5 | 2.0 | 55 55 | 14x11 6HX | 14 | 18 | 100 | 37.5 | ||
| JHTM18×2-6HXECP | M18x2 | 1.0 | 58 | 15x12 6HX | 15 | 20 | 100 | 37.5 | ||
| JHTM20×1-6HXECP | M20x1 | 1.5 | 58 | 15x12 6HX | 15 | 20 | 105 105 | 37.5 | ||
| JHTM20×1.5-6HXECP | M20x1.5 | 58 | 15x12 6HX | 15 | 37.5 | |||||
| JHTM20×2-6HXECP | M20x2 | 2.0 | 20 | 105 | 37.5 | |||||
●标准库存 ○订单生产
| 加工材料Workpiecematerial | 碳素钢低合金钢Carbon steelLow-alloy steel | 合金钢调制钢Alloy steelTempered Alloy steel | 高硬钢、淬硬刚High-hardnessHardened steel | 铁素体、马氏体奥氏体不锈钢Femitic,Martensitic、Austenitic | 铸铁Cast iron | 铜合金Copperalloy | 铝合金铸铝Aluminumalloy | 石墨Graphite | 钛合金Titaniumalloy | 镍基合金Nickell-base alloy | 塑料Plastic | |
| (HB≤252) | (HRC ≤ 40) | (40-50HRC) ( | 50-55HRC)(> 55HRC) | |||||||||
| 涂层 Coated | ★ | ★ | ★ ★ | |||||||||
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
挤压 Forming
JIS 日标通用挤压丝锥系列 C/2-3PJIS Standard General HSSE Forming Tap
| 型号 Model 涂层 Coated | 库存 Stock | TDZ | 尺寸 Dimension/mm | |||||||
| TP | LU | CZCMS | TCTR | DCONMS | TD | LF | THL | |||
| JNRM3-6HXCCH | M3 | 0.5 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4-6HXCCH | M4 | 0.7 | 21 5x4 | 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5-6HXCCH | M5 | 0.8 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6-6HXCCH | M6 | 1.0 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8-6HXCCH | M8 | 1.25 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10-6HXCCH | M10 | 1.5 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12-6HXCCH | M12 | 1.75 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14-6HXCCH | M14 | 2.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16-6HXCCH | M16 | 2.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18-6HXCCH | M18 | 2.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM20-6HXCCH | M20 | 2.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM3×0.35-6HXCCH | M3x0.35 | 0.35 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4×0.5-6HXCCH | M4x0.5 | 0.5 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5×0.5-6HXCCH | M5x0.5 | 0.5 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6×0.5-6HXCCH | M6x0.5 | 0.5 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM6×0.75-6HXCCH | M6x0.75 | 0.75 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8×0.75-6HXCCH | M8x0.75 | 0.75 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM8×1-6HXCCH | M8x1 | 1.0 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10×1-6HXCCH | M10x1 | 1.0 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM10×1.25-6HXCCH | M10x1.25 | 1.25 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12×1-6HXCCH | M12x1 | 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.25-6HXCCH | M12x1.25 | 1.25 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.5-6HXCCH | M12x1.5 | 1.5 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14×1-6HXCCH | M14x1 | 1.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.25-6HXCCH | M14x1.25 | 1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.5-6HXCCH | M14x1.5 | 1.5 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16×1-6HXCCH | M16x1 | 1.0 | 52 | 12.5x10 6HX 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM16×1.5-6HXCCH | M16x1.5 | 1.5 | 52 | 12.5x10 | 12.5 | 16 | 95 | 22 | ||
| JNRM18×1-6HXCCH | M18x1 | 1.0 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM18×1.5-6HXCCH | M18x1.5 | 1.5 | 55 | 14x11 6HX 14x11 | 14 | 18 | 100 | 27.5 | ||
| JNRM18×2-6HXCCH | M18x2 | 2.0 | 55 | 6HX 6HX | 14 15 | 18 | 100 | 27.5 | ||
| JNRM20×1-6HXCCH | M20x1 | 1.0 1.5 | 58 58 | 15x12 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×1.5-6HXCCH | M20x1.5 | 58 | 15x12 6HX | 20 | 105 | 27.5 | ||||
| JNRM20×2-6HXCCH | M20x2 | 2.0 | 15 | 20 | 105 | 27.5 | ||||
●标准库存 ○订单生产
切削材料推荐
Cutting material recommendation
Cutting material recommendation
| 加工材料Workpiecematerial | 碳素钢 低合金钢Carbon steelLow-alloy steel | 合金钢调制钢Alloy steelTempered Alloy steel | 高硬钢、淬硬刚High-hardnessHardened steel | 铁素体、马氏体奥氏体不锈钢Femitic、Martensitic,Austenitic | 铸铁Cast iron | 铜合金Copperalloy | 铝合金铸铝Aluminumalloy | 石墨Graphite | 钛合金Titaniumalloy | 镍基合金Nickell-base alloy | 塑料Plastic | ||
| (HB≤252) | (HRC ≤ 40) | (40-50HRC)) ( | 50-55HRC)(& | gt; 55HRC) | |||||||||
| 涂层 Coated | ★ ☆ | ||||||||||||
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
挤压 Forming
JIS 日标通用挤压丝锥系列 E/1.5-2PJIS Standard General HSSE Forming Tap
| 型号 Model 涂层 Coated | 库存 Stock | TDZ | 尺寸 Dimension/mm | |||||||
| TP | LU | CZCMS | TCTR | DCONMS | TD | LF | THL | |||
| JNRM3-6HXECH | M3 | 0.5 19 | 4x3.2 | 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4-6HXECH | M4 | 0.7 | 21 5x4 | 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5-6HXECH | M5 | 0.8 | 24 5.5x4.5 | 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6-6HXECH | M6 | 1.0 | 29 6x4.5 | 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8-6HXECH | M8 | 1.25 | 37 6.2x5 | 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10-6HXECH | M10 | 1.5 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12-6HXECH | M12 | 1.75 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14-6HXECH | M14 | 2.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16-6HXECH | M16 | 2.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18-6HXECH | M18 | 2.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM20-6HXECH | M20 | 2.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM3×0.35-6HXECH | M3x0.35 | 0.35 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4×0.5-6HXECH | M4x0.5 | 0.5 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5×0.5-6HXECH | M5x0.5 | 0.5 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6×0.5-6HXECH | M6x0.5 | 0.5 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM6×0.75-6HXECH | M6x0.75 | 0.75 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8×0.75-6HXECH | M8x0.75 | 0.75 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM8×1-6HXECH | M8x1 | 1.0 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10×1-6HXECH | M10x1 | 1.0 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM10×1.25-6HXECH | M10x1.25 | 1.25 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12×1-6HXECH | M12x1 | 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.25-6HXECH | M12x1.25 | 1.25 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.5-6HXECH | M12x1.5 | 1.5 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14×1-6HXECH | M14x1 | 1.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.25-6HXECH | M14x1.25 | 1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.5-6HXECH | M14x1.5 | 1.5 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16×1-6HXECH | M16x1 | 1.0 | 52 | 12.5x10 6HX 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM16×1.5-6HXECH | M16x1.5 | 1.5 | 52 | 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18×1-6HXECH | M18x1 | 1.0 | 55 | 14x11 | 14 | 18 | 100 | 27.5 | ||
| JNRM18×1.5-6HXECH | M18x1.5 | 1.5 | 55 | 14x11 6HX 14x11 | 14 | 18 | 100 | 27.5 | ||
| JNRM18×2-6HXECH | M18x2 | 2.0 | 55 58 | 6HX 15x12 6HX | 14 15 | 18 | 100 | 27.5 | ||
| JNRM20×1-6HXECH | M20x1 | 1.0 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×1.5-6HXECH | M20x1.5 | 1.5 2.0 | 58 | 15x12 6HX | 15 | 20 20 | 105 | 27.5 | ||
| JNRM20×2-6HXECH | M20x2 | 105 | 27.5 | |||||||
●标准库存 ○订单生产
切削材料推荐 Cutting material recommendation
| 加工材料 Workpiece material | 碳素钢 低合金钢 Carbon steel Low-alloy steel | 合金钢 调制钢 Alloy steel | 高硬钢、淬硬刚 High-hardness Hardened steel | 铁素体、马氏体 奥氏体不锈钢 Femitic、 Martensitic, | 铸铁 Cast iron | 铜合金 Copper | 铝合金 铸铝 | 石墨 | 镍基 钛合金 合金 Nickell- | 塑料 | |
| (HB≤252) | Tempered Alloy steel (HRC ≤ 40) | (40-50HRC) | (50-55HRC)( > 55HRC) | Austenitic | alloy | Aluminum alloy | Graphite | Titanium alloy | Plastic base alloy | ||
| 涂层 Coated | ★ | ☆ | ★★ |
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
挤压 Forming
JIS 日标高性能挤压丝锥系列 C/2-3P
JIS Standard High-Performance HSSE-PM Forming Tap
| TD | ||||
| CZCMS T DCONMS t | ||||
| THL | 1 | |||
| LU | ||||
| LF | ||||
| 型号 Model 涂层 Coated | 库存 Stock | 尺寸 Dimension/mm | ||||||||
| TDZ | TP | LU | CZCMS | TCTR DCONMS | TD | LF | THL | |||
| JNRM2-6HXCCP | M2 | 0.4 | 16 | 3x2.5 6HX | 3 | 2 | 40 | 4 | ||
| JNRM2.5-6HXCCP | M2.5 | 0.45 | 16 | 3x2.5 6HX | 3 | 2.5 | 44 | 5 | ||
| JNRM3-6HXCCP | M3 | 0.5 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4-6HXCCP | M4 | 0.7 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5-6HXCCP | M5 | 0.8 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6-6HXCCP | M6 | 1.0 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8-6HXCCP | M8 | 1.25 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10-6HXCCP | M10 | 1.5 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12-6HXCCP | M12 | 1.75 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14-6HXCCP | M14 | 2.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16-6HXCCP | M16 | 2.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18-6HXCCP | M18 | 2.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM20-6HXCCP | M20 | 2.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM3×0.35-6HXCCP | M3x0.35 | 0.35 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4×0.5-6HXCCP | M4x0.5 | 0.5 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5×0.5-6HXCCP | M5x0.5 | 0.5 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6×0.5-6HXCCP | M6x0.5 | 0.5 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM6×0.75-6HXCCP | M6x0.75 | 0.75 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8×0.75-6HXCCP | M8x0.75 | 0.75 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM8×1-6HXCCP | M8x1 | 1.0 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10×1-6HXCCP | M10x1 | 1.0 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM10×1.25-6HXCCP | M10x1.25 | 1.25 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12×1-6HXCCP | M12x1 | 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.25-6HXCCP | M12x1.25 | 1.25 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.5-6HXCCP | M12x1.5 | 1.5 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14×1-6HXCCP | M14x1 | 1.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.25-6HXCCP | M14x1.25 | 1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.5-6HXCCP | M14x1.5 | 1.5 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16×1-6HXCCP | M16x1 | 1.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM16×1.5-6HXCCP | M16x1.5 | 1.5 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18×1-6HXCCP | M18x1 | 1.0 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM18×1.5-6HXCCP | M18x1.5 | 1.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM18×2-6HXCCP | M18x2 | 2.0 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM20×1-6HXCCP | M20x1 | 1.0 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×1.5-6HXCCP | M20x1.5 | 1.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×2-6HXCCP | M20x2 | 2.0 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
●标准库存 ○订单生产
切削材料推荐 Cutting material recommendation
| 加工材料Workpiecematerial | 碳素钢 低合金钢Carbon steelLow-alloy steel | 合金钢调制钢Alloy steelTempered Alloy steel | 高硬钢、淬硬刚High-hardnessHardened steel | 铁素体、马氏体奥氏体不锈钢Femitic、Martensitic,Austenitic | 铸铁Cast iron | 铜合金Copperalloy | 铝合金铸铝Aluminumalloy | 石墨Graphite | 钛合金Titaniumalloy | 镍基合金Nickell-base alloy | 塑料Plastic | ||
| (HB≤252) | (HRC ≤ 40) | (40-50HRC) | (50-55HRC)(& | gt; 55HRC) | |||||||||
| 涂层 Coated | ★★ | ★★ | |||||||||||
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
挤压 Forming
JIS 日标高性能挤压丝锥系列 E/1.5-2PJIS Standard High-Performance HSSE-PM Forming Tap
| 型号 Model 涂层 Coated | 库存 Stock | TDZ | 尺寸 Dimension/mm | |||||||
| TP | LU | CZCMS | TCTR | DCONMS | TD | LF | THL | |||
| JNRM2-6HXECP | M2 | 0.4 | 16 | 3x2.5 6HX | 3 | 2 | 40 | 4 | ||
| JNRM2.5-6HXECP | M2.5 | 0.45 | 16 3x2.5 | 6HX | 3 | 2.5 | 44 | 5 | ||
| JNRM3-6HXECP | M3 | 0.5 | 19 4x3.2 | 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4-6HXECP | M4 | 0.7 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5-6HXECP | M5 | 0.8 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6-6HXECP | M6 | 1.0 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8-6HXECP | M8 | 1.25 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10-6HXECP | M10 | 1.5 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12-6HXECP | M12 | 1.75 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14-6HXECP | M14 | 2.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16-6HXECP | M16 | 2.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18-6HXECP | M18 | 2.5 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM20-6HXECP | M20 | 2.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM3×0.35-6HXECP | M3x0.35 | 0.35 | 19 | 4x3.2 6HX | 4 | 3 | 46 | 5.5 | ||
| JNRM4×0.5-6HXECP | M4x0.5 | 0.5 | 21 | 5x4 6HX | 5 | 4 | 52 | 7.7 | ||
| JNRM5×0.5-6HXECP | M5x0.5 | 0.5 | 24 | 5.5x4.5 6HX | 5.5 | 5 | 60 | 8.8 | ||
| JNRM6×0.5-6HXECP | M6x0.5 | 0.5 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM6×0.75-6HXECP | M6x0.75 | 0.75 | 29 | 6x4.5 6HX | 6 | 6 | 62 | 11 | ||
| JNRM8×0.75-6HXECP | M8x0.75 | 0.75 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM8×1-6HXECP | M8x1 | 1.0 | 37 | 6.2x5 6HX | 6.2 | 8 | 70 | 13.5 | ||
| JNRM10×1-6HXECP | M10x1 | 1.0 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM10×1.25-6HXECP | M10x1.25 | 1.25 | 41 | 7x5.5 6HX | 7 | 10 | 75 | 16.5 | ||
| JNRM12×1-6HXECP | M12x1 | 1.0 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.25-6HXECP | M12x1.25 | 1.25 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM12×1.5-6HXECP | M12x1.5 | 1.5 | 48 | 8.5x6.5 6HX | 8.5 | 12 | 82 | 19.5 | ||
| JNRM14×1-6HXECP | M14x1 | 1.0 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.25-6HXECP | M14x1.25 | 1.25 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM14×1.5-6HXECP | M14x1.5 | 1.5 | 48 | 10.5x8 6HX | 10.5 | 14 | 88 | 22 | ||
| JNRM16×1-6HXECP | M16x1 | 1.0 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM16×1.5-6HXECP | M16x1.5 | 1.5 | 52 | 12.5x10 6HX | 12.5 | 16 | 95 | 22 | ||
| JNRM18×1-6HXECP | M18x1 | 1.0 | 55 | 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM18×1.5-6HXECP | M18x1.5 | 1.5 2.0 | 55 | 14x11 6HX 14x11 6HX | 14 | 18 | 100 | 27.5 | ||
| JNRM18×2-6HXECP | M18x2 | 55 | 14 | 18 | 100 | 27.5 | ||||
| JNRM20×1-6HXECP | M20x1 | 1.0 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×1.5-6HXECP | M20x1.5 | 1.5 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
| JNRM20×2-6HXECP | M20x2 | 2.0 | 58 | 15x12 6HX | 15 | 20 | 105 | 27.5 | ||
●标准库存 ○订单生产
切削材料推荐 Cutting material recommendation
| 加工材料Workpiecematerial | 碳素钢 低合金钢Carbon steelLow-alloy steel | 合金钢调制钢Alloy steelTempered Alloysteel | 高硬钢、淬硬刚High-hardnessHardened steel | 铁素体、马氏体奥氏体不锈钢Femitic,Martensitic,Austenitic | 铸铁Cast iron | 铜合金Copperalloy | 铝合金铸铝Aluminumalloy | 石墨Graphite | 钛合金Titaniumalloybase | 镍基合金Nickell-alloy | 塑料Plastic |
| (HB≤252) ( | HRC ≤ 40) | (40-50HRC)(50-55HRC)(> 55HRC) | |||||||||
| 涂层 Coated | ★ ★ | ||||||||||
★首选 First choice ☆可选 Good choice
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
＊因各类被加工材料加工性能差异较大，上表只列出适用的大类，如有具体材质，请查阅C216做进一步确认。 ＊ For specific material,please refer to C216 for further information.
SEGNC森泰英格
ISO 13399标准规定的切削刀具参数
Cutting tool parameters according to ISO 13399
所有切削刀具都由ISO 13399标准规定的若干个参数定义。您可以在该列表中找到切削刀具参数及其定义。
All cutting tools are defined by a number of parameters according to the standard ISO 13399, such as depth of cutor cutting diameter. You find both the cutting tool parameter and its definition in this list.
| 参数 | 定义 | Definition |
| ADINTMS | 机床侧适配接口 | Adaptive interface machine direction |
| ADINTWS | 工件侧适配接口 | Adaptive interface workpiece direction |
| AERMX | 最大切宽与刀具直径比 | Working engagement ratio maximum |
| ALP | 轴向后角 | Axial clearance angle |
| AN | 主后角 | Clearance angle major |
| ANN | 副后角 | Clearance angle minor |
| APMX | 最大切削深度 | Depth of cut maximum |
| AXGSUP | 轴向槽支撑方向 | Axial groove support direction |
| AZ | 最大插铣深度 | Maximum plunge depth |
| B | 刀柄宽度 | Shank width |
| BAMS | 机床侧的刀体角度 | Machine side body angle |
| BAWS | 工件侧刀体角度 | Workpiece side body angle |
| BBD | 通过设计平衡 | Balanced by design |
| BBR | 通过旋转测试平衡 | Balanced by rotational test |
| BD | 刀体直径 | Body diameter |
| BHTA | 刀体半锥角 | Body half taper angle |
| BLMC | 平衡方法代码 | Balancing method code |
| BMC | 本体材料代码 | Body material code |
| BN | 刀面刃带宽度 | Face land width |
| BS Wiper | 修光刃）长度 | Wiper edge length |
| BSG | 基本标准组 | Identifier for the standard defining the tool design |
| BSR | 修光刃半径 | Wiper edge radius |
| CBMD | 断屑器制造商名称 | Chip breaker manufacturer's designation |
| CCC | 中央切削能力 | Center cutting capability |
| CCONWS | 工件侧连接数 | Workpiece side connection count |
| CDX | 最大切削深度 | Cutting depth maximum |
| CEDC | 切削刃数 | Cutting edge count |
| CGX | 用于重心位置的X组件 | X-component for center of gravity location |
| CGY | 用于重心位置的Y组件 | Y-component for center of gravity location |
| CGZ | 用于重心位置的Z组件 | Z-component for center of gravity location |
| CHW | 刀尖倒角宽度 | Corner chamfer width |
| CICT | 切削部件数 | Cutting item count |
| CND | 冷却液入口直径 | Coolant entry diameter |
| CNSC | 冷却液入口型式代码 | Coolant entry style code |
| CNT | 冷却液入口螺纹尺寸 | Coolant entry thread size |
| COATING | 涂层 | Coating |
| CONARWS | 工件侧连接布置 | Connection arrangement workpiece side |
| CP | 冷却液压力 | Coolant pressure |
| CPDF | 切削分度差异 | Cutting pitch differential |
| CRKS | 连接固定旋钮螺纹型号 | Connection retention knob thread size |
| CTPT | 工序类型 | Operation type |
| CUTDIA | 最大工件切断直径 | Work piece parting diameter maximum |
| CUTINT_MASTER | 切削部件接口标识符第2部分 | Part two of two identifiers of cutting item interface |
| CUTINT_SIZESHAPE | 刀片尺寸和形状 | Insert size and shape |
| CW | 切削宽度 | Cutting width |
| CWTOLL | 切削宽度公差下限 | Cutting width lower tolerance |
| CWTOLU | 切削宽度公差上限 | Cutting width upper tolerance |
| CXSC | 冷却液出口型式代码 | Coolant exit style code |
| CXST | 冷却液出口供应类型 | Coolant exit supply type |
| CZC | 连接型号代码 | Connection size code |
| CZC MS | 机床侧连接型号代码 | MS Connection size code machine side |
| CZC WS | 工件侧连接型号代码 | WS Connection size code workpiece side |
| D1 | 固定孔直径 | Fixing hole diameter |
| DAH | 检修孔直径 | Diameter access hole |
| DAXIN | 轴向槽最小内径 | Axial groove inside diameter minimum |
| DAXN | 轴向槽最小外径 | Minimum axial groove outside diameter |
| DAXX | 轴向槽最大外径 | Maximum axial groove outside diameter |
| DBC | 螺栓环直径 | Diameter bolt circle |
| DC | 切削直径 | Cutting diameter |
| DCB | 连接孔直径 | Connection bore diameter |
| DCBN | 最小连接孔直径 | Connection bore diameter minimum |
| DCBX | 最大连接孔直径 | Connection bore diameter maximum |
| DCF | 刀面接触切削直径 | Cutting diameter face contact |
| DCN | 最小切削直径 | Minimum cutting diameter |
| DCON | 连接直径 | Connection diameter |
| DCONMS | 机床侧接口直径 | Connection diameter machine side |
| DCONWS | 工件侧连接直径 | Connection diameter workpiece side |
| DCP | 数据芯片口袋 | Data chip pocket |
| DCPS | 数据芯片口袋尺寸 | Data chip pocket size |
| DCSFMS | 机床侧接触表面直径 | Contact surface diameter machine side |
| DCSFWS | 工件侧接触表面直径 | Contact surface diameter workpiece side |
| DCTOLL | 切削直径公差下限 | Lower cutting diameter tolerance |
| DCTOLU | 切削直径公差上限 | Upper cutting diameter tolerance |
| DCX | 最大切削直径 | Maximum cutting diameter |
| DFC | 作用直径 | Functional diameter |
| DHUB | 毂直径 | Hub diameter |
| DIX | 换刀器最大干涉直径 | Tool changer interference diameter maximum |
| DMIN | 最小孔径 | Minimum bore diameter |
| DMM | 刀柄直径 | Shank diameter |
| DN | 颈部直径 | Neck diameter |
| DPC | 减振性能 | Damping property |
| DSGN | 设计 | Design |
| FHA | 容屑槽螺旋角 | Flute helix angle |
| FLGT | 法兰厚度 | Flange thickness |
| FTDZ | 螺纹直径尺寸 | For thread diameter size |
| GAMF | 径向前角 | Radial rake angle |
| GAMO | 垂直前角 | Orthogonal rake angle |
| GAMP | 轴向前角 | Axial rake angle |
| GAN | 刀片前角 | Insert rake angle |
| GB | 面刃带角 | Face land angle |
| GRADE | 材质 | The brand name for grade |
| H | 刀柄高度 | Shank height |
| HAND | 旋向 | Hand |
| HBL | 切削头底部偏置长度 | Head bottom offset length |
| HDD | 切削头直径 | Head diameter |
| HEAD_TYPE | 切削头类型 | Type of head |
| HF | 工作高度 | Functional height |
| HRY | 参考平面的最低点 | Lowest point from reference plain |
| HTB | 刀体高度 | Body height |
| HTH | 高度 | Height |
| HTY | 孔型 | Hole type |
| IC | 内切圆直径 | Inscribed circle diameter |
| IEP | 间断切削刃特性 | Interupted edge property |
| IFS | 刀片座类型代码 | Insert mounting style code |
| INSL | 刀片长度 | Insert length |
| IZC KAP | 刀片型号代码 | Insert size code |
| KAPR | K(绕z轴旋转) | Kappa (z-axis rot) |
| KCH | 刀具切削刃角 | Tool cutting edge angle |
| KGRP_INT | 刀尖倒角 | Corner chamfer |
| KGRPS | 按键夹紧接口 | Key grip interface |
| KGRPTP | 从动部件规格 | Size of driven part |
| KRINS | 从动部件几何特性 | Geometrical characteristic driven part |
| L | 主切削刃角 | Major cutting edge angle |
| LAMS | 切削刃长度 | Cutting edge length |
| LB | 刃倾角 | Inclination angle |
| LCF | 刀体长度 | Body length Chip flute length |
| LE | 容屑槽长度 | |
| LF | 切削刃有效长度 | Cutting edge effective length |
| LGR | 功能长度 | Functional length |
| LH | 重新研磨长度 | Regrind length |
| LIG | 切削头长度 | Head length |
| LOCAP | 刃口干涉长度 | Insert gauge length |
| LPR | 定位辅助特性 | Location aid property |
| LS | 伸出长度 | Protruding length |
| LSC | 刀柄长度 | Shank length |
| LSCN | 夹紧长度 | Clamping length |
| LSCX | 最小夹紧长度 | Clamping length minimum |
| LSD | 最大夹紧长度 刀柄绝对长度 | Clamping length maximum Dead shank length |
| LU | Usable length | |
| MHD | 有效长度(最大推荐值) 安装孔距离 | Mounting hole distance |
| MIID | Master insert identification | |
| MMCC | 主刀片标识 | Code for preset torque |
| MMCX | 预调扭矩代码 | Maximum cutting torque |
| MRAT | 切削扭矩 | Main rotation angle of tool |
| MTP | 刀具主旋转角 | Clamping type code |
| 夹紧类型代码 | Flute count | |
| NOF | 容屑槽数 | Maximum regrinds |
| NORGMX OAH | 最大重新研磨次数 总高 | Overall height |
| OAL | 总长 | Overall length |
| OAW | 总宽 | Overall width |
| OHN | 最小悬伸 | Minimum overhang |
| OHX | 最大悬伸 | Maximum overhang |
| PHD | 预加工孔直径 | Premachined hole diameter |
| PHDX | 最大预加工孔直径 | Maximum premachined hole diameter |
| PHT | 预加工孔类型 | Premachined hole type |
| PL | 顶尖长度 | Point length |
| PRFRAD | 轮廓半径 | Profile radius |
| PRSPC | 轮廓规格 | Profile specification |
| PSIR | 刀具导程角 | Tool lead angle |
| PSIRL | 左手主切削刃角 | Major left hand cutting edge angle |
| PSIRR | 右手主切削刃角 | Major right hand cutting edge angle |
| RADH | 径向刀体高度 | Radial body height |
| RADW | 径向刀体宽度 | Radial body width |
| RE | 刀尖半径 | Corner radius |
| REEQ | 刀尖圆角半径等值 | Corner radius equivalent |
| REL RER | 左侧圆角半径 | Corner radius left |
| RETOLL | 右侧圆角半径 | Corner radius right |
| RETOLU | 刀尖半径公差下限 | Corner radius lower tolerance |
| 刀尖半径公差上限 | Corner radius upper tolerance | |
| RIDOP | 反转旋转方向输出侧 | Reversed rotation direction output side |
| RMPX | 最大坡走铣角度 | Maximum ramping angle |
| RPMX | 最大转速 | Rotational speed maximum |
| S SC | 刀片厚度 | Insert thickness |
| 刀片形状代码 | Insert shape code | |
| SCREW_TYPE | 螺钉类型 | Screw type |
| SDL | 台阶直径长度 | Step diameter length |
| SEAL SEP | 密封性能 | Sealing property |
| 传感器嵌入式属性 | Sensor embedded property | |
| SIG | 外刃顶角 | Point angle |
| SPA | 球形轮廓角 | Sphere profile angle |
| SSC | 刀片座尺寸代码 | Insert seat size code |
| STA | 台阶夹角 | Step included angle |
| SUBSTRATE | 基体 | Substrate |
| TA TCDC | 丝锥角度 | Taper angle |
| TCDCON | 切削直径公差等级 | Tolerance class cutting diameter |
| TCDMM | 刀柄直径公差 | Connection diameter tolerance |
| TCHA | 刀柄直径公差 | Shank diameter tolerance |
| TCL | 可达到的孔公差 | Achievable hole tolerance |
| TCT | 螺纹加工倒角长度 | Tap chamfer length |
| 刀具公差等级 | Tolerance class tool | |
| TCTR | 螺纹公差等级 | Thread tolerance class |
| TD | 螺纹直径 | Thread diameter |
| TDZ | 螺纹直径尺寸 | Thread diameter size |
| TFLA | 丝锥前部浮动长度 | Tap floating length ahead Tap floating length behind |
| TFLB TG | 丝锥后部浮动长度 丝锥梯度 | Taper gradient |
| Thread back taper property | ||
| THBTP | 螺纹背锥特性 |
| THCA | 螺纹螺旋校正角度 | Thread helix correction angle |
| THCHT | 螺纹加工倒角类型 | Threading chamfer type |
| THDH | 螺纹旋向 | Thread hand |
| THFT | 形式类型 | Form type |
| THL | 螺纹长度 | Threading length |
| THLGTH | 螺纹长度 | Thread length |
| THUB | 轮毂厚度 | Hub thickness |
| TP | 螺纹螺距 | Thread pitch |
| TPI | 每英寸螺纹数 | Threads per inch |
| TPIN | 每英寸最小螺纹数 | Threads per inch minimum |
| TPIX | 每英寸最大螺纹数 | Threads per inch maximum |
| TPN | 最小螺距 | Thread pitch minimum |
| TPX | 最大螺距 | Maximum thread pitch |
| TQ | 扭矩 | Torque |
| TSYC | 刀具类型代码 | Tool style code |
| ULDR | 有用长度直径比 | Usable length diameter ratio |
| W1 | 刀片宽度 | Insert width |
| WB | 刀体宽度 | Body width |
| WEP | 修光刃特性 | Wiper edge property |
| WF | 工作宽度 | Functional width |
| WSC | 夹紧宽度 | Clamping width |
| WT | 部件重量 | Weight of item |
| XYPFEEDIR XY | 平面进给方向 | XY-plane feed direction |
| ZEFF | 表面有效切削刃数 | Number of cutting edges that are effective on the face of a tool |
| ZEFP | 周边有效切削刃数 | Peripheral effective cutting edge count |
| ZWX | Wiper(修光刃)刀片的最大数量 | Maximum number of Wiper inserts |
