该页无缩略图
MiSTtMa4n0 d标a准r刀d杆
| RTMC-用于标准螺纹 配件 | |||||||||
| 刀片类型 | 订货代码 | 尺寸mm | 切削槽 数量 | S | |||||
| L | L1 | D | D1 | D2 | 定位螺钉 锁紧螺钉×2 | Torx+扳手 | |||
| 40 | RTMC2522-43L3 | 102 | 43 | 25 18 | 22 | 3 | SLD4IP8A (M4x0.7) | SCD4IP8 只能使用包装内配套的 (M4x0.7) VardexTorx+扳手。 最大扭矩1.2Nm | |
| RTMC2522-65L3 | 124 | 65 | 25 18 | 22 | 3 | ||||
| RTMC3230-55L4 | 117 | 55 | 32 26 | 30 | 4 | ||||
| BRTMC3230-80L3 | 142 | 80 | 32 26 | 30 | 3 | ||||
标准刀杆螺纹加工范围
| 刀杆 最小螺纹直径 | |||||||
| D2 (mm) | ISO (粗牙) | ISO (细牙) | UNC | UN/UNF/UNEF/UNS | BSF | BSP(G) | |
| RTMC2522-43L3 | 22 | M27x3 | M25x1:M25×x25 | 1-14UNS-UN-U | 1-14 1-1 | 3/4-14 | |
| RTMC2522-65L3 | 22 | M27x3 | M24x1; M24x1.5 M25x2; M25x2.5 | 111/6-8UN; 1-9UN; 1-10UNS; 1-12UNF 1-14UNS; 1-16UN; 1-18UN; i5/16-20UNEF | 1-11; 1-12; 1-14; 1-16; | 3/4-14 | |
| RTMC3230-55L4 | 30 | M32x1; M32x1.5 M33x2; M33x2.5; M34x3 | 13/-8UN; 1³/g-9UN; 13/g-10UN; 15/16-12UN; 13/-14UNS;15/16-16UN;15/16-18UNEF;15/16-20UN | 13/8-11; 13/g-12; 13/-14; 13/8-16 | 1-11 | ||
| BRTMC3230-80L3 | 30 | M32x1; M32x1.5 M33x2; M33x2.5; M34x3 | 13/-8UN;1³/8-9UN; 1³/8-10UN; 15/16-12UN; 13/&-14UNS; 15/16-16UN; 15/16-18UNEF; 15/16-20UN | 13/8-11; 13/8-12; 13/-14; 13/8-16 | 1-11 | ||
2步安装法
MiTM40 刀盘
推荐使用中心孔冷却，特别当D2>0.7 x 公称螺孔直径
| 锥度和标准铣刀盘 | |||||||||||
| 刀片类型 | 订货代码 | 尺寸mm | D | ||||||||
| D1 | D2 | d(H7) | H | Z | 定位螺钉 | 螺紧×2 | 刀杆打 | ||||
| 标准型 | 40 | RTMC-D44-22-40L6 | 40 | 44 | 22 | 48 | 6 | SLD4IP.8A | Torx+ KIP8 | M10x1.5x40 | |
| RTMC-D52-27-40L8 | 48 | 52 | 27 | 50 | 8 | SM40.7) 只能使用包套的 推荐 | M12x1.75x40 | ||||
| 锥度 | RTMNC-D45-22-40L6 | 40 | 45 | 22 | 48 | 6 | 最大扭矩1.2Nm | M10x1.5x40 | |||
标准刀杆螺纹加工范围
| 刀杆 | 最小螺纹直径 | |||||
| D2 (mm) | ISO (细牙) | UN/UNF/UNEF/UNS | BSW | BSP(G) | ||
| 标准型 | RTMC-D44-22-40L6 | 44 | M48x1:M48x15: | 17-UN:UN | 2-16 | 11/2-11 |
| RTMC-D52-27-40L8 | 52 | M55x2:M55x15: | 2/4-UN2-UN2U4 | 2/4-16 | 2-11 | |
锥度刀杆螺纹加工范围
| 刀杆 最小螺纹直径 | ||||
| D2 (mm) | NPT | NPTF | BSPT | |
| 锥度 | RTMNC-D45-22-40L6 45 | 2-11.5;21/2-8 (及更大螺纹) | 2-11.5; 21/2-8; 3-8 | 2-6x11 |
2步安装法
MiTM41 标准刀杆
推荐使用中心孔冷却，特别当D2>0.7 x 公称螺孔直径
| RTMC-用于标准螺纹 | ||||||||||
| 刀片类型 | 订货代码 | 切数 | ||||||||
| L | L1 | D | D1 | D2* | Z | 定位螺钉×2 | 压紧螺钉 | Torx+扳手 | ||
| RTMC2521-45B1 | 105 | 45 | 25 | 16.0 | 21.2 | 1 | SCD4IP8 (M4x0.7) | KIP8 只能使用包装内配套的 VardexTorx+扳手。 | ||
| RTMC2524-43B2 | 104 43 | 25 | 19.2 | 24.5 | 2 | |||||
| RTMC3230-43B3 | 106.5 43 | 32 | 24.2 | 30.0 | 3 | |||||
| RTMC3230-65B3 | 128.5 | 65 | 32 | 24.2 | 30.0 | 3 | ||||
| RTMC3236-43B5 | 106 | 43 | 32 | 28.3 | 35.9 | 5 | ||||
标准刀杆螺纹加工范围
| 刀杆 最小螺纹直径 | ||||||||||
| D2* (mm) | ISO (粗牙) | ISO (细牙) | UNC | UN/UNF/UNEF/UNS | BSW/BSF | NPT | NPTF | |||
| RTMC2521-45B1 | 21.2 | M27x3; M30x3.5; M33×3.5; M36x4;M30x3; M42×4 M39x4 | 1-8, 11/-7; 11/4-7; 13/8-6; 11/2-6 | 11/16-8UN;17/6-6UN 1-8BSW; 11/8-7BSW | ||||||
| RTMC2524-43B2 | 24.5 | M30x3.5; M36x4 | M28x3;M45x4 | 11/8-7; 13/8-6 | 1/g-8UN; | 17/16-6UN13/&-8BSF；1/4-7BSW | ||||
| RTMC3230-43B3 | 30.0 | M36x4; M42x4.5 | M34X3; M34x3.5; | 13/-6 | 13/-8UN; 17/16-6UN | 1%-8SF 19-4785F | ||||
| RTMC3230-65B3 | 30.0 | M36x4; M42x4.5 | M34x3; M34x3.5; 13/-6 M45x4 | 13/8-8UN; 17/6-6UN | 1/2-6BSW | 13/8-8BSF；13/4-7BSF; | ||||
| RTMC3236-43B5 | 35.9 | M56x5.5; M64x6 | M42x4.5; M48x5;M40x3; M40x3.5; M42x4; M70x6 | 13/4-5; 2-4.5; 21/2-4 | 15/%-8UN; 1/%-6UN | 15/%-8BSF; 17/8-6BSF | 13/4-7BSF; | 21/2-8 | 21/2-8 | |
| RTMC3236-65B4 | 35.9 | M56x5.5;M64x6 | M42x4.5; M48x5;M40x3; M40×3.5; M42x4; M70x6 | 13/4-5; 2-4.5; 4 | 21/2-15/8-8UN; 15/8- 6UN | 1/8-6BSF | 15/-8BSF；13/4-7BSF; | 21/2-8 | 21/2-8 | |
\* 外螺纹加工时刀片R41E…CNC程序时直径设定为 . 0 2 + 0 . 6 \mathsf {mm } )。
2步安装法
MiTM41刀盘
推荐使用中心孔冷却，特别当D2>0.7 x 公称螺孔直径
| 标准型盘铣刀 | |||||||||||
| 刀片类型 | 订货代码 | 尺寸mm | 切削槽数量 | ||||||||
| D1 | D2* | d(H7) | H | Z | 定位螺钉×2 | 压紧螺钉 | Torx+扳手 | 刀杆 螺钉 | |||
| 41 | RTMC-D48-22-41B5 | 40 | 47.9 | 22 | 50 | 5 | SLD4IP8A (M4x0.7) | SCD4IP8 | KIP8 只能使用包装内配套的Vardex Torx+扳手。 | M10x1.5x40 | |
| RTMC-D58-27-41B6 | 50 | 57.9 | 27 | 50 | 6 | (M4x0.7) 推荐 最大扭矩1.2Nm | M12x1.75x40 | ||||
标准刀杆螺纹加工范围
| 刀杆 最小螺纹直径 | ||||||||||
| D2* (mm) | ISO (粗牙) | ISO (细牙) | UNC | UN/UNF/UNEF/UNS | BSF | NPT | NPTF | |||
| RTMC-D48-22-41B5 | 47.9 | M56x5.5; M64x6 | M55x4; M70x6; | 2/4-4.5; 21/2-4 | 21/-8UN; 2/-6UN | 21/4-8; 21/4-6 | 212-8 | 21/2-8 | ||
| RTMC-D58-27-41B6 | 57.9 | M68x6 | M64x4; M70x6 | 23/4-4 | 21/2-8UN; 21/2-6UN | 21/2-8; 23/4-6 | 21-8 | 21/2-8 | ||
\* 外螺纹加工时刀片R41E…CNC程序时直径设定为 ( \mathsf { D } 2 + 0 . 6 \mathsf {mm } ^ { \mathsf { ^ { * } } } )。
2步安装法
推荐材质，切削速度Vc [ \mathsf { m / m i n } ] 和进给f[mm/齿]
| 材料 组 | snae 材料 | 布氏硬度 | Vc [m/min] | 进给f [mm/tooth] | |||
| VBX | VTX | (不包括MiTM19) | (针对MiTM19) | ||||
| P 钢 | 1 23 非合金钢 | 低碳钢(C=0.1-0.25%) | 125 | 100-210 | 90-180 | 0.1-0.35 | 0.06-0.2 |
| 中碳钢(C=0.25-0.55%) | 150 | 100-180 | 90-170 | 0.1-0.4 | 0.06-0.25 | ||
| 高碳钢 (C=0.55-0.85%) | 170 | 100-170 | 90-160 | 0.1-0.35 | 0.06-0.2 | ||
| 未淬火 | 180 | 80-140 | 90-155 | 0.1-0.4 | 0.06-0.25 | ||
| 低合金≤5%） | 淬火 | 275 | 80-150 | 80-160 | 0.1-0.35 | 0.06-0.2 | |
| 淬火 | 350 | 70-140 | 70-150 | 0.1-0.3 | 0.06-0.2 | ||
| 6 7 高合金钢 | 退火 | 200 | 60-130 | 70-115 | 0.1-0.35 | 0.06-0.2 | |
| 8 （合金含量>5%) | 淬火 | 325 | 70-110 | 60-100 | 0.1-0.2 | 0.06-0.1 | |
| 9 铸钢 | 低合金钢 (合金含量≤5%) | 200 | 100-170 | 100-170 | 0.1-0.3 | 0.06-0.2 | |
| 10 | 高合金钢 （合金含量>5%） | 225 | 70-120 | 70-130 | 0.1-0.2 | 0.06-0.1 | |
| M 不锈钢 | 11 不锈钢 12铁素体 13 | 未淬火 | 200 | 100-170 | 120-180 | 0.1-0.3 | 0.06-0.2 |
| 淬火 | 330 | 100-170 | 120-180 | 0.1-0.2 | 0.06-0.1 | ||
| 不锈钢 14奥氏体 | 奥氏体 | 180 | 70-140 | 100-140 | 0.1-0.3 | 0.06-0.2 | |
| 超级奥氏体 | 200 | 70-140 | 100-140 | 0.1-0.2 | 0.06-0.1 | ||
| 15 不锈钢 16铸铁 | 未淬火 | 200 | 70-140 | 100-140 | 0.1-0.3 | 0.06-0.2 | |
| 淬火 | 330 | 70-140 | 100-140 | 0.1-0.2 | 0.06-0.1 | ||
| 17 不锈钢 18奥氏体 | 奥氏体 | 200 | 70-120 | 100-120 | 0.1-0.3 | 0.06-0.2 | |
| 淬火 | 330 | 70-120 | 100-120 | 0.1-0.2 | 0.06-0.1 | ||
| K 30 铸铁 31 | 28 可锻 29铸铁 | 铁素体 (短切屑) | 130 | 60-130 | 100-120 | 0.05-0.16 | 0.03-0.1 |
| 珠光体 (长切屑) | 230 | 60-120 | 80-100 | 0.04-0.1 | 0.02-0.06 | ||
| 灰铸铁 | 低拉伸强度 | 180 | 60-130 | 80-100 | 0.1-0.3 | 0.06-0.2 | |
| 高拉伸强度 | 260 | 60-100 | 80-100 | 0.1-0.2 | 0.06-0.1 | ||
| 32 球磨铸铁 33 | 铁素体 | 160 | 60-125 | 80-100 | 0.1-0.3 | 0.06-0.2 | |
| 珠光体 | 260 | 50-90 | 60-90 | 0.1-0.2 | 0.06-0.1 | ||
| N 有色金属 38 39 | 34 铝合金 35 -锻造件 | 100-250 | |||||
| 无时效处理 | 60 | - | 0.15-0.55 | 0.09-0.3 | |||
| 3037 铝合金 | 时效处理 | 100 | 100-180 | 0.15-0.5 | 0.09-0.3 | ||
| 转&时效处理 | 590 | 150-400 | - | 0.1-045 | 000-05 | ||
| 铝合金 铜及 | 130 | 80-150 | |||||
| 铸件硅含量13-22% | 120-210 | 0.15-0.5 | 0.09-0.3 | ||||
| 19 20 S 21 耐热材料 22 23 | 40铜合金 高温 | 黄铜 青铜及无铅铜 | 90 100 | 120-210 | 100-200 100-200 | 0.15-0.5 0.1-0.4 | 0.09-0.3 0.06-0.25 |
| 退火(铁基) | 20-45 | 20-40 | 0.1-0.2 | 0.06-0.1 | |||
| 时效(铁基) | 200 280 | 20-30 | 20-30 | 0.04-0.1 | 0.02-0.06 | ||
| 合金 | 退火 (镍基或钴基) | 250 | 15-20 | 15-20 | 0.04-0.1 | 0.02-0.06 | |
| 时效 (镍基或钴基) | 350 | 10-15 | 10-15 | 0.04-0.1 | 0.02-0.06 | ||
| 99.5纯钛 | 400Rm | 70-140 | 70-120 | 0.04-0.1 | 0.02-0.06 | ||
| 24 25 | 钛合金 | α+β相钛合金 | 1050Rm 45-50HRc | 20-50 15-45 | 20-50 15-45 | 0.04-0.1 | 0.02-0.06 |
| H 硬化材料 | 超硬钢 26 | 淬硬&调质 | 0.06-0.12 | 0.04-0.07 | |||
| 51-55HRc | 15-40 | 15-40 | 0.04-0.08 | 0.02-0.05 | |||
材质
| 材质 | 应用 | 实例 |
| VBX | TiC件和通用材料加工。 | |
| VTX | TiAIN加工的理想材质。 |
标准型
Vardex产品订货码
螺纹铣削刀片
螺纹铣刀刀杆
螺纹铣刀盘
螺纹铣削标准系列
ISO公制螺纹
外螺纹/内螺纹
标准参照: R262 (DIN 13) 公差等级: 6g/6H
标准型螺纹铣刀
| 全螺纹说力 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | mm | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 6.0mm | 10.4 | 0.5 | 6.010.5ISOTM... | 10.0 | 20 | TMMC..-6.0 | |
| 0.75 | 6.010.75ISOTM... | 9.75 | 13 | ||||
| 1.0 | 6.011.0ISOTM... | 9.0 | 9 | ||||
| 1.25 | 6.011.25ISOTM... | 8.75 | 7 | ||||
| 1.5 | 6.0I1.5ISOTM... | 9.0 | 6 | ||||
| 1/4" | 0.5 | 2I0.5ISOTM2... | 10.0 | 20 | TMSH.2-2 | ||
| 0.75 | 2E0.75ISOTM2... | 2I0.75ISOTM2... | 10.5 | 14 | |||
| 1.0 | 2E1.0ISOTM2... | 2I1.0ISOTM2... 10.0 | 10 | ||||
| 1.25 | 2E1.25ISOTM2... | 10.0 | 8 | ||||
| 1.25 | 2I1.25ISOTM2... | 8.75 | 7 | ||||
| 1.5 | 2E1.5ISOTM2... | 9.0 | 6 | ||||
| 1.5 | 2I1.5ISOTM2... | 10.5 | 7 | ||||
| 3/8" | 16 | 0.5 | 310.5ISOTM2... | 15.0 | 30 | TMC..-3 TMSH..-3 | |
| 0.75 | 3E0.75ISOTM2... | 310.75ISOTM2... | 15.0 | 20 | |||
| 0.8 | 310.8ISOTM2... | 14.4 | 18 | ||||
| 1.0 | 3E1.0ISOTM2... | 14.0 | 14 | ||||
| 1.0 | 3I1.0ISOTM2... | 15.0 | 15 | ||||
| 1.25 | 3E1.25ISOTM2... | 3I1.25ISOTM2... | 15.0 | 12 | |||
| 1.5 | 3E1.5ISOTM2... | 3I1.5ISOTM2... | 15.0 | 10 | |||
| 1.75 | 3E1.75ISOTM2... | 3I1.75ISOTM2... | 14.0 | 8 | |||
| 3/8"B | 2.0 | 3E2.0ISOTM2... | 312.0ISOTM2... | 14.0 | 7 | TMMC.-3B | |
| 1.0 | 3BE1.0ISOTM2... | 3BI1.0ISOTM2... | 22.0 | 22 | |||
| 1.25 | 3BE1.25ISOTM2... | 3BI1.25ISOTM2... | 21.25 | 17 | |||
| 1.5 | 3BE1.5ISOTM2... | 3BI1.5ISOTM2... | 21.0 | 14 | |||
| 1.75 | 3BE1.75ISOTM2... | 3BI1.75ISOTM2... | 21.0 | 12 | |||
| 5/8" | 2.0 1.0 | 3BE2.0ISOTM2... 5E1.0ISOTM2... | 3Bl2.0ISOTM2... 5I1.0ISOTM2... | 22.0 26.0 | 11 | TMSH-5 | |
| 1.25 | 5E1.25ISOTM2... | 26 20 | |||||
| 1.5 | 5E1.5ISOTM2... | 5I1.25ISOTM2... 5I1.5ISOTM2... | 25.0 25.5 | 17 | |||
| 1.75 | 5E1.75ISOTM2... | 5I1.75ISOTM2... | 24.5 | 14 | |||
| 2025 | SE2.1S0TM.... | 512.01SOTM2.... | 240 | 1210 | |||
| 3.0 | 5E3.0ISOTM2... | 513.0ISOTM2... | 24.0 | 8 | |||
| 3.5 | 5E3.5ISOTM2... | 513.5ISOTM2... | 24.5 | 7 | |||
| 4.0 | 5E4.0ISOTM2... | 514.0ISOTM2... | 24.0 | 6 | |||
| 4.5 | 5E4.5ISOTM2... | 514.5ISOTM2... | 22.5 | 5 | |||
所有刀片有两个切削刃，除了MiniTM ( \mathsf { I C } 6 . 0 \mathsf {mm } ) 只有一个切削刃。
ISO 公制螺纹 （续）
外螺纹/内螺纹
标准参照: R262 (DIN 13) 公差等级: 6g/6H
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | mm | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 3/4"B | 1.5 | 6BE1.5ISOTM2... | 6BI1.5ISOTM2... | 36.0 | 24 | TMCH-.6B | |
| 2.0 | 6BE2.0ISOTM2... | 6Bl2.0ISOTM2... | 36.0 | 18 | |||
| 2.5 | 6BE2.5ISOTM2... | 6Bl2.5ISOTM2... | 35.0 | 14 | |||
| 3.0 | 6BE3.0ISOTM2... | 6BI3.0ISOTM2... | 36.0 | 12 | |||
| 4.0 | 6BE4.0ISOTM2... | 6Bl4.0ISOTM2... | 32.0 | 8 | |||
| 4.5 | 6BE4.5ISOTM2... | 6BI4.5ISOTM2... | 31.5 | 7 | |||
| 5.0 | 6BE5.0ISOTM2... | 6BI5.0ISOTM2... | 30.0 | 6 | |||
| 5.5 | 6BE5.5ISOTM2... | 6BI5.5ISOTM2... | 33.0 | 6 | |||
| 6.0 | 6BE6.0ISOTM2... | 6Bl6.0ISOTM2... | 30.0 | 5 | |||
标准型 螺纹铣刀
内螺纹
标准参照: R262 (DIN 13) 公差等级: 6g/6H
粗牙螺纹铣刀
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| Lmm | IC | mm | 刀杆 | mm | ||||
| M10x0.75 | 6.0mm | 10.4 | 6.010.75ISOTM028/001... | 1 | 9.75 | 13 | TMMC12-6.0 | 9.1-10 |
| M10x0.75 | 6.0I0.75ISOTM028/00.1.. | 1 | 9.75 | 13 | TMMC20-6.0 | 9.1-10 | ||
| M12x1.25 | 6.0I1.25ISOTM028/002.. | 1 | 8.75 | 7 | TMMC12-6.0 | 10.6-11.4 | ||
| M12x1.25 | 6.0I1.25ISOTM028/002... | 1 | 8.75 | 7 | TMMC20-6.0 | 10.6-11.4 | ||
| M12x1.75 | 6.0I1.75ISOTM028/003.. | 1 | 8.75 | 5 | TMMC20-6.0-124/003 | 10.1-19 | ||
| M14x2.0 | 1/4" | 11 | 2I2.0ISOTM028/00... | 2 | 10.0 | 5 | TMC12-2 | 11.8-19.5 |
| M14x2.0 | 2I2.0ISOTM028/00.. | 2 | 10.0 | 5 | TMC20-2 | 11.8-19.5 | ||
| M16x2.0 | 2I2.0ISOTM028/004... | 2 | 10.0 | 5 | TMC12-2 | 11.8-19.5 | ||
| M16x2.0 | 2l2.0ISOTM028/004... | 2 | 10.0 | 5 | TMC20-2 | 11.8-19.5 | ||
| M20x2.5 | 3/8″ | 16 | 3l2.5ISOTM028/005... | 1 | 12.5 | 5 | TMC16-3-124/001 | 17.2-19.2 |
| M22x2.5 | 4I2.5ISOTM028/006... | 1 | 17.5 | 7 | TMC25-4-124/002 | 19.2-31.6 | ||
| M24x3.0 | 1/2″ | 22 | 4I3.0ISOTM028/00.7... | 1 | 18.0 | 6 | TMC25-4-124/002 | 20.7-32.7 |
| M27x3.0 | 4I3.0ISOTM028/00.7... | 1 | 18.0 | 6 | TMC25-4-124/002 | 20.7-32.7 | ||
| M30x3.5 | 5/8″ | 27 | 5I3.5ISOTM028/008.. | 2 | 24.5 | 7 | TMC25-5-124/004 | 26.2-35.9 |
| M33x3.5 | 5I3.5ISOTM028/008... | 2 | 24.5 | 7 | TMC25-5-124/004 | 26.2-35.9 | ||
| M36x3.0 | 5I3.0ISOTM028/00... | 2 | 24.0 | 8 | TMC25-5 | 32.7-39 | ||
| M36x4.0 | 514.0ISOTM028/010... | 2 | 24.0 | 6 | TMC25-5 | 31.6-38.5 | ||
| M39x3.0 | 5I3.0ISOTM028/00.. | 2 | 24.0 | 8 | TMC25-5 | 32.7-39 | ||
| M39x4.0 | 514.0ISOTM028/010.. | 2 | 24.0 | 6 | TMC25-5 | 31.6-38.5 | ||
| M42x4.5 | 514.5ISOTM028/011... | 2 | 22.5 | 5 | TMC25-5 | 37.1-48 | ||
| M45x4.5 | 5I4.5ISOTM028/011... | 2 | 22.5 | 5 | TMC25-5 | 37.1-48 | ||
| M48x5.0 | 5I5.0ISOTM028/075... | 2 | 20.0 | 4 TMC25-5 | 38.9-8 | |||
| M52x5.0 | 5I5.0ISOTM028/075... | 2 | 20.0 | 4 TMC25-5 | 38.9-8 | |||
外螺纹/内螺纹
标准参照: R262 (DIN 13) 公差等级: 6g/6H
标准型 螺纹铣刀
TMO刀杆的标准TM刀片
| 刀片尺寸 | 螺距 | 订货代码 | ECL | |||
| IC | Lmm | mm | 外螺纹 | 内螺纹 | 刀杆 | mm |
| 1/4" | 0.5 | 2I0.5ISOTM2... | TMOC20-2-8 | 19.0 | ||
| 0.75 | 2E0.75ISOTM2... | 2I0.75ISOTM2... | TMOC20-2-9 | 19.5 | ||
| 1.0 | 2E1.0ISOTM2... | 2I1.0ISOTM2... | TMOC20-2-8 | 19.0 | ||
| 1.25 | 2E1.25ISOTM2... | TMOC20-2-10 | 18.7 | |||
| 1.25 | 2I1.25ISOTM2... | TMOC20-2-10 | 16.2 | |||
| 1.5 | 2E1.5ISOTM2... | TMOC20-2-8 | 18.0 | |||
| 1.5 | 2I1.5ISOTM2. | TMOC20-2-8 | 19.5 | |||
| 3/8" | 0.5 | 310.5ISOTM2... | TMOC20-3-1 | 28.5 | ||
| 0.5 | 310.5ISOTM2... | TMOC20-3-10 | 29.0 | |||
| 0.75 | 3E0.75ISOTM2... | 310.75ISOTM2... | TMOC20-3-11 | 28.5 | ||
| 1.0 | 3E1.0ISOTM2... | TMOC20-3-10 | 28.0 | |||
| 1.0 | 3I1.0ISOTM2... | TMOC20-3-10 | 29.0 | |||
| 1.25 | 3E1.25ISOTM2... | 3I1.25ISOTM2... | TMOC20-3-7 | 28.7 | ||
| 1.5 | 3E1.5ISOTM2... | 3I1.5ISOTM2... | TMOC20-3-1 | 28.5 | ||
| 1.75 | 3E1.75ISOTM2... | 3I1.75ISOTM2... | TMOC20-3-12 | 26.2 | ||
| 2.0 | 3E2.0ISOTM2... | 312.0ISOTM2... | TMOC20-3-10 | 28.0 | ||
| 5/8" | 1.0 | 5E1.0ISOTM2... | 5I1.0ISOTM2... | TMOC25-5-12 | 46.0 | |
| 1.0 | 5E1.0ISOTM2... | 511.0ISOTM2... | TMOC25-5-16 | 47.0 | ||
| 1.25 | 5E1.25ISOTM2... | 5I1.25ISOTM2... | TMOC25-5-13 | 48.7 | ||
| 1.5 | 5E1.5ISOTM2... | 5I1.5ISOTM2... | TMOC25-5-14 | 48.0 | ||
| 1.5 | 5E1.5ISOTM2... | 5I1.5ISOTM2... | TMOC25-5-16 | 46.5 | ||
| 1.75 | 5E1.75ISOTM2... | 5I1.75ISOTM2.. | TMOC25-5-15 | 47.2 | ||
| 2.0 | 5E2.0ISOTM2... | 512.0ISOTM2... | TMOC25-5-12 | 44.0 | ||
| 2.5 | 5E2.5ISOTM2... | 5l2.5ISOTM2... | TMOC25-5-12 | 45.0 | ||
| 2.5 | 5E2.5ISOTM2... | 5l2.5ISOTM2... | TMOC25-5-14 | 47.5 | ||
| 3.0 | 5E3.0ISOTM2... | 5I3.0ISOTM2... | TMOC25-5-16 | 45.0 | ||
| 3.5 | 5E3.5ISOTM2... | 513.5ISOTM2... | TMOC25-5-16 | 45.5 | ||
| 4.0 | 5E4.0ISOTM2... | 514.0ISOTM2... | TMOC25-5-12 | 44.0 | ||
| 4.5 | 5E4.5ISOTM2... | 514.5ISOTM2... | TMOC25-5-14 | 45.0 | ||
| 5.0 | ||||||
| 5I5.0ISOTM...028/075 | TMOC25-5-12 | 40.0 | ||||
外螺纹/内螺纹
标准参照: R262 (DIN 13) 公差等级: 6g/6H
细牙螺纹铣刀
细牙螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | mm | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 6.0mm | 0.35 | 6.0E0.35ISOTMF... | 6.010.35ISOTMF... | 9.45 | 14 | ||
| 0.4 | 6.0E0.4ISOTMF... | 6.010.4ISOTMF... | 9.2 | 12 | |||
| 0.45 | 6.0E0.45ISOTMF... | 6.010.45ISOTMF... | 9.45 | 11 | |||
| 0.5 | 6.0E0.5ISOTMF... | 9.5 | 10 | ||||
| 0.6 | 6.0E0.6ISOTM.F... | 9.0 | 8 | ||||
| 0.7 | 6.0E0.7ISOTMF... | 9.1 | 7 | ||||
| 0.75 | 6.0E0.75ISOTMF... | 8.25 | 6 | ||||
| 0.8 | 6.0E0.8ISOTMF... | 8.8 | 6 | ||||
| 0.9 | 6.0E0.9ISOTMF... | 8.1 | 5 | ||||
| 1/4" | 0.35 | 2E0.35ISOTM2F... | 2I0.35ISOTM2F.. | 10.15 | 15 | TMSH.2 | |
| 0.4 | 2E0.4ISOTM2F... | 2I0.4ISOTM2F... | 10.0 | 13 | |||
| 0.45 | 2E0.45ISOTM2F... | 2I0.45ISOTM2F... | 9.45 | 11 | |||
| 500 | 2E0.51S0TM2F... | 109 | |||||
| 9.52 | |||||||
| 0.7 | 2E0.7ISOTM2F... | 9.1 | 7 | ||||
| 0.8 | 2E0.8ISOTM2F... | 8.8 | 6 | ||||
| 0.9 | 2E0.9ISOTM2F... | 9.9 | 6 | ||||
| 0.35 | 3E0.35ISOTM2F... | 310.35ISOTM2F... | 14.35 | 21 | |||
| 3/8″ | 0.4 | 3E0.4ISOTM2F... | 310.4ISOTM2F.. | 14.8 | 19 | ||
| 0.45 | 3E0.45ISOTM2F... | 310.45ISOTM2F... | 14.85 | 17 | |||
| 0500 | 3E051SOTM2E | 135138 | 1412 | ||||
| 0.7 | 3E0.7ISOTM2F.. | 14.7 | 11 | ||||
| 0.8 | 3E0.8ISOTM2F... | 13.6 | 9 | ||||
| 0.9 | 3E0.9ISOTM2F... | 13.5 | 8 | ||||
注意：完成螺纹加工,需走两次螺旋插补轨迹. 细牙螺纹铣刀片完成范牙型螺纹。订货示例：6.0E0.35ISOTMF VBX所有刀片有两个切削刃，除了MiniTM \mathsf { I C 6 . 0mm } ) 只有一个切削刃。更多刀杆信息，请参阅282页。
细牙螺纹
细牙螺纹螺距较小，由于相邻齿的刀尖圆弧过小，因此细牙多齿螺纹刀片的制造非常困难。瓦格斯公司设计开发的细牙多齿螺纹刀片其齿间距为两倍细牙螺距。
重要提示！
• 所有细牙螺纹刀片为范围牙型（因加大刀尖圆弧所致)。
O
美制UN
外螺纹/内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
标准型螺纹铣刀
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 6.0mm | 10.4 | 32 | 6.0132UNTM... | 9.53 | 12 | TMMC..-6.0 | |
| 28 | 6.0128UNTM... | 9.07 | 10 | ||||
| 24 | 6.0124UNTM... | 9.53 | 9 | ||||
| 20 | 6.0120UNTM... | 8.89 | 7 | ||||
| 18 | 6.0I18UNTM.. | 8.47 | 6 | ||||
| 16 | 6.0I16UNTM... | 7.94 | 5 | ||||
| 1/4" | 48 | 2I48UNTM2... | 10.05 | 19 | TMSH-2-2 | ||
| 40 | 2I40UNTM2... | 10.16 | 16 | ||||
| 32 | 2I32UNTM2... | 10.32 | 13 | ||||
| 28 | 2E28UNTM2... | 2I28UNTM2... | 9.98 | 11 | |||
| 724 | 2E27UNTM.. | 2127UNTM2... | 19 | ||||
| 1035 | |||||||
| 20 | 2E20UNTM2... | 2I20UNTM2... | 10.16 | 8 | |||
| 18 | 2E18UNTM2... | 2I18UNTM2... | 9.88 | 7 | |||
| 16 | 2E16UNTM2... | 2I16UNTM2... | 9.53 | 6 | |||
| 14 40 | 2E14UNTM2... | 2I14UNTM2... 3140UNTM2... | 9.07 14.61 | 5 23 | |||
| 3/8" | 32 | 3I32UNTM2... | 15.08 | 19 | |||
| 28 | 3E28UNTM2... | 3l28UNTM2... | 14.51 | 16 | |||
| 27 | 3E27UNTM2... | 3I27UNTM2... | 14.11 | 15 | |||
| 26 | 3E26UNTM2... | 3126UNTM2... | 14.65 | 15 | |||
| 24 | 3E24UNTM2... | 3124UNTM2... | 14.82 | 14 | |||
| 16 | 3E20UNTM2... | 3120UNTM2... | 13.97 | 11 | |||
| 20 18 | 3E18UNTM2... | 3I18UNTM2... | 14.11 | 10 | |||
| 3E16UNTM2... | 3I16UNTM2... | ||||||
| 16 14 | 3E14UNTM2... | 3114UNTM2... | 14.29 | 9 8 | |||
| 3/8"B | 3E13UNTM2... | 3I13UNTM2... | 14.51 | 6 | |||
| 13 12 | 13.68 14.82 | 7 | |||||
| 11.5 | 3E12UNTM2... | 3I12UNTM2... 3I11.5UNTM2... | 13.25 | 6 | |||
| 24 | 3E11.5UNTM2... | 3BI24UNTM2... | 21.16 | 20 | |||
| 20 | 3BE24UNTM2... 3BE20UNTM2... | 3Bl20UNTM2... | 21.59 | 17 | |||
| 18 | 3BE18UNTM2... | 3BI18UNTM2... | 21.17 | 15 | |||
| 16 | 3BE16UNTM2... | 3BI16UNTM2... | 20.64 | 13 | |||
| 14 | |||||||
| 13 | 3BE14UNTM2... | 3BI14UNTM2... 3BI13UNTM2... | 21.77 21.49 | 12 11 | |||
| 12 | 3BE13UNTM2... 3BE12UNTM2... | 3BI12UNTM2... | 21.17 | 10 | |||
所有刀片有两个切削刃，除了MiniTM 1 0 . 6 . 0 \ : {mm } ) 只有一个切削刃。更多刀杆信息，请参阅282页。
美制UN (续)
外螺纹/内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 5/8" 27 | 24 | 5E24UNTM2... | 5l24UNTM2... | 25.40 | 24 | ||
| 20 | 5E20UNTM2... | 5l20UNTM2... | 25.40 | 20 | |||
| 18 | 5E18UNTM2... | 5I18UNTM2... | 25.40 | 18 | |||
| 16 | 5E16UNTM2... | 5I16UNTM2... | 25.40 | 16 | |||
| 14 | 5E14UNTM2... | 5I14UNTM2... | 25.40 | 14 | |||
| 13 | 5E13UNTM2... | 5I13UNTM2.. | 25.40 | 13 | |||
| 12 | 5E12UNTM2... | 5I12UNTM2... | 25.40 | 12 | |||
| 11.5 | 5E11.5UNTM2... | 5111.5UNTM2... | 24.30 | 11 | |||
| 11 | 5E11UNTM2... | 5I11UNTM2... | 25.40 | 11 | |||
| 10 | 5E10UNTM2... | 22.86 | 9 | ||||
| 10 | 5I10UNTM2... | 25.40 | 10 | ||||
| 9 | 5E9UNTM2... | 5I9UNTM2... | 22.58 | 8 | |||
| 8 | 5E8UNTM2... | 5I8UNTM2... | 22.23 | 7 | |||
| 7 | 5E7UNTM2... | 21.77 | 6 | ||||
| 7 | 5I7UNTM2... | 25.40 | 7 | ||||
| 6 | 5E6UNTM2... | 21.17 | 5 | ||||
| 38.5 | 6 | 5I6UNTM2... | 25.40 | 6 | |||
| 6 | 6BE6UNTM2.. | 6Bl6UNTM2... | 33.87 | 8 | TMC.-6B TMSH..-6B | ||
| 5 | 6BE5UNTM2... | 6BI5UNTM2... | 30.48 | 6 | |||
| 4.5 | 6BE4.5UNTM2.. | 6BI4.5UNTM2. | 33.87 | 6 | |||
| 4 | 6BE4UNTM2... | 6BI4UNTM2... | 31.75 | 5 | |||
标准型螺纹铣刀
美制UN (续)
内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
粗牙螺纹铣刀
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| Lmm | IC | 内螺纹 | mm | 刀杆 | mm | |||
| 7/16"-20UNF | 6.0l20UNTM028/012.. | 1 | 8.89 | 7 | TMMC12-6.0 | 9.7-11.4 | ||
| 7/16"-20UNF | 6.0l20UNTM028/012... | 1 | 8.89 | 7 | TMMC20-6.0 | 9.7-11.4 | ||
| 7/16"-16UN | 6.0mm | 10.4 6.0I16UNTM028/014... | 1 | 7.94 | 5 TMMC12-6.0 | 9.3-14.1 | ||
| 7/16"-16UN | 6.0I16UNTM028/014.. | 1 | 7.94 | 5 | TMMC20-6.0 | 9.3-14.1 | ||
| 7/16"-14UNC | 6.0I14UNTM028/013... | 1 | 9.07 | 5 | TMMC20-6.0-124/003 | 9.1-9.9 | ||
| 1/2"-13UNC | 1/4" | 11 | 2I13UNTM028/015... | 1 | 9.77 | 5 | TMC20-2-124/005 | 10.5-19.5 |
| 1/2"-16UN | 6.0mm | 10.4 | 6.0116UNTM028/014.. | 1 | 7.94 | 5 | TMMC12-6.0 | 9.3-14.1 |
| 1/2"-16UN | 6.0116UNTM028/01. | 1 | 7.94 | 5 | TMMC20-6.0 | 9.3-14.1 | ||
| 9/16"-12UNC | 2I12UNTM028/016... | 1 | 8.47 | 4 | TMC20-2-124/005 | 11.9-15.6 | ||
| 9/16"-18UNF | 1/4" | 11 | 2I18UNTM028/017... | 2 | 9.88 | 7 | TMC12-2 | 12.7-14.5 |
| 9/16"-18UNF | 2I18UNTM028/017... | 2 | 9.88 | 7 | TMC20-2 | 12.7-14.5 | ||
| 9/16"-16UN | 6.0I16UNTM028/014.. | 1 | 7.94 | 5 | TMMC12-6.0 | 9.3-14.1 | ||
| 9/16"-16UN | 6.0mm | 10.4 | 6.0I16UNTM028/014. | 1 | 7.94 | 5 | TMMC20-6.0 | 9.3-14.1 |
| 5/8"-11UNC | 2I11UNTM028/018.. | 1 | 9.24 | 4 | TMC20-2-124/006 | 13.3-18.5 | ||
| 5/8"-12UN | 1/4" | 11 | 2I12UNTM028/016... | 1 | 8.47 | 4 | TMC20-2-124/005 | 11.9-15.6 |
| 5/8"-16UN | 6.0I16UNTM028/014. | 1 | 7.94 | 5 | TMMC12-6.0 | 9.3-14.1 | ||
| 5/8"-16UN | 6.0mm | 10.4 11 | 6.0I16UNTM028/014... | 1 | 7.94 | 5 | TMMC20-6.0 | |
| 11/16"-12UN 1/4" | 2I12UNTM028/016... | 1 | TMC20-2-124/005 | 9.3-14.1 | ||||
| 3/4"-10UNC | 3/8″ | 16 | 3I10UNTM028/019... | 1 | 8.47 | 4 | TMC16-3-124/001 | 11.9-15.6 |
| 3/4"-12UN | 3I12UNTM028/020... | 12.70 | 5 | 16.3-31.6 | ||||
| 1/2″ | 22 | 2 | 14.82 | 7 | TMNC16-3 | 16.7-18.3 | ||
| 13/16"-12UN 7/8"-9UNC | 3I12UNTM028/020... 4I9UNTM028/021... | 2 1 | 14.82 16.93 | 7 6 | TMC16-3 TMC25-4-124/002 | 18.3-19.5 19.1-32.5 | ||
美制UN (续)
内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
粗牙螺纹铣刀
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| IC | 内螺纹 | mm | 刀杆 | mm | ||||
| 1"-8UNC | 1/2″ | Lmm 22 | 4I8UNTM028/022... | 1 | 19.05 | 6 | TMC25-4-124/007 | 21.9-28.3 |
| 1 1/16"-8UN | 4I8UNTM028/02... | 1 | 19.05 | 6 | TMC25-4-124/007 | 21.9-28.3 | ||
| 1 1/8"-7UNC | 4I7UNTM028/023... | 1 | 18.14 | 5 | TMC25-4-124/002 | 24.6-35.9 | ||
| 1 1/8"-8UN | 4I8UNTM028/022... | 1 | 19.05 | 6 | TMC25-4-124/007 | 21.9-28.3 | ||
| 1 3/16"-8UN | 4I8UNTM028/022.. | 1 | 19.05 | 6 | TMC25-4-124/007 | 21.9-28.3 | ||
| 1 1/4"-7UNC | 4I7UNTM028/023... | 1 | 18.14 | 5 | TMC25-4-124/002 | 24.6-35.9 | ||
| 1 1/4"-8UN | 5I8UNTM028/024... | 2 | 22.23 | 7 | TMC25-5-124/004 | 28.3-33.0 | ||
| 1 5/16"-8UN | 5I8UNTM028/024. | 2 | 22.23 | 7 | TMC25-5-124/004 | 28.3-33.0 | ||
| 13/8"-6UNC | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5-124/004 | 30.3-36.7 | ||
| 13/8"-8UN | 5I8UNTM028/024... | 2 | 22.23 | 7 | TMC25-5-124/004 | 28.3-33.0 | ||
| 1 7/16"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5-124/004 | 30.3-36.7 | ||
| 1 7/16"-8UN | 5I8UNTM028/024... | 2 | 22.23 | 7 | TMC25-5 | 33.0-39.0 | ||
| 1 1/2"-6UNC | 5I6UNTM028/025... | 2 | 25.40 | 6 TMC25-5-124/004 | 30.3-36.7 | |||
| 1 1/2"-8UN | 5I8UNTM028/024... | 2 2 | 22.23 7 | TMC25-5 | 33.0-39.0 | |||
| 19/16"-6UN | 27 | 5I6UNTM028/025... | 25.40 | 6 | TMC25-5-124/004 | 30.3-36.7 | ||
| 19/16"-8UN | 518UNTM028/024... | 2 | 22.23 | 7 | TMC25-5 | 33.0-39.0 | ||
| 15/8"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
| 1 5/8"-8UN | 5I8UNTM028/024... | 2 | 22.23 | 7 | TMC25-5 | 33.0-39.0 | ||
| 1 11/16"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
| 1 3/4"-5UNC | 5I5UNTM028/077... | 2 | 20.32 | 4 | TMC25-5 | 38.9-8 | ||
| 1 3/4"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
| 1 13/16"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
| 1 7/8"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
| 1 15/16"-6UN | 5I6UNTM028/025... | 2 | 25.40 | 6 | TMC25-5 | 36.7-45.0 | ||
美制UN (续)
外螺纹/内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
标准型螺纹铣刀
TMO刀杆的标准TM刀片
| 刀片尺寸 | 螺距 | 订货代码 | ECL | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | 刀杆 | mm |
| 1/4" | 48 | 2I48UNTM2... | TMOC20-2-1 | 19.58 | ||
| 48 | 2I48UNTM2... | TMOC20-2-2 | 18.52 | |||
| 48 | 2I48UNTM2... | TMOC20-2-9 | 19.05 | |||
| 32 | 2I32UNTM2... | TMOC20-2-1 | 19.85 | |||
| 28 | 2E28UNTM2... | 2I28UNTM2... | TMOC20-2-3 | 17.24 | ||
| 24 | 2E24UNTM2... | 2I24UNTM2... | TMOC20-2-2 | 17.99 | ||
| 20 | 2E20UNTM2... | 2I20UNTM2... | TMOC20-2-4 | 19.05 | ||
| 18 | 2E18UNTM2... | 2I18UNTM2... | TMOC20-2-2 | 18.34 | ||
| 16 | 2E16UNTM2... | 2I16UNTM2... | TMOC20-2-1 | 19.05 | ||
| 14 | 2E14UNTM2... | 2I14UNTM2... | TMOC20-2-3 | 16.33 | ||
| 3/8" | 32 | 3I32UNTM2... | TMOC20-3-3 | 27.78 | ||
| 32 | 3132UNTM2... | TMOC20-3-11 | 28.58 | |||
| 28 | 3E28UNTM2.. | 3I28UNTM2.. | TMOC20-3-3 | 27.21 | ||
| 27 | 3E27UNTM2... | 3I27UNTM2... | TMOC20-3-4 | 27.28 | ||
| 24 | 3E24UNTM2... | 3I24UNTM2... | TMOC20-3-6 | 27.52 | ||
| 20 | 3E20UNTM2... | 3120UNTM2... | TMOC20-3-6 | 26.67 | ||
| 18 | 3E18UNTM2... | 3I18UNTM2... | TMOC20-3-6 | 26.82 | ||
| 16 | 3E16UNTM2... | 3I16UNTM2... | TMOC20-3-6 | 26.99 | ||
| 14 | 3E14UNTM2... | 3I14UNTM2... | TMOC20-3-6 | 27.21 | ||
| 13 | 3E13UNTM2... | 3I13UNTM2... | TMOC20-3-2 | |||
| 12 | 3E12UNTM2... | 3I12UNTM2... | 25.4 | |||
| 11.5 | 3E11.5UNTM2... | 3111.5UNTM2... | TMOC20-3-6 TMOC20-3-5 | 27.52 24.3 | ||
美制UN (续)
外螺纹/内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
标准型螺纹铣刀
TMO刀杆的标准TM刀片
| 刀片尺寸 | 螺距 | 订货代码 | ECL | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | 刀杆 | mm |
| 5/8" | 24 | 5E24UNTM2.. | 5124UNTM2.. | TMOC25-5-1 | 50.80 | |
| 24 | 5E24UNTM2... | 5124UNTM2... | TMOC25-5-2 | 46.57 | ||
| 20 | 5E20UNTM2... | 5I20UNTM2... | TMOC25-5-1 | 50.80 | ||
| 18 | 5E18UNTM2... | 5I18UNTM2... | TMOC25-5-1 | 50.80 | ||
| 18 | 5E18UNTM2... | 5I18UNTM2... | TMOC25-5-2 | 46.57 | ||
| 16 | 5E16UNTM2... | 5I16UNTM2... | TMOC25-5-3 | 47.63 | ||
| 14 | 5E14UNTM2... | 5I14UNTM2... | TMOC25-5-1 | 50.80 | ||
| 14 | 5E14UNTM2... | 5I14UNTM2... | TMOC25-5-4 | 47.17 | ||
| 13 | 5E13UNTM2... | 5I13UNTM2... | TMOC25-5-1 | 50.80 | ||
| 12 | 5E12UNTM2... | 5I12UNTM2... | TMOC25-5-2 | 46.57 | ||
| 27 | 12 | 5E12UNTM2... | TMOC25-5-1 | 50.80 | ||
| 11.5 | 5E11.5UNTM2... | 5I11.5UNTM2... | TMOC25-5-5 | 46.38 | ||
| 11 | 5E11UNTM2... | 5I11UNTM2... | TMOC25-5-6 | 48.49 | ||
| 11 | 5I11UNTM2... | TMOC25-5-1 | 46.18 | |||
| 10 | 5E10UNTM2... | TMOC25-5-7 | 43.18 | |||
| 10 | 5I10UNTM2... | TMOC25-5-7 | 45.72 | |||
| 9 | 5E9UNTM2... | 5I9UNTM2... | TMOC25-5-8 | 45.16 | ||
| 8 | 5E8UNTM2... | 518UNTM2... | TMOC25-5-9 | 44.45 | ||
| 7 | 5E7UNTM2... | TMOC25-5-10 | 43.54 | |||
| 7 | 5I7UNTM2... | TMOC25-5-10 | 47.17 | |||
| 6 | 5E6UNTM2... | TMOC25-5-2 | 42.33 | |||
| 6 | 5I6UNTM2... | TMOC25-5-2 | 46.57 | |||
| 5 | 5I5UNTM...028/077 | TMOC25-5-7 | 40.64 | |||
美制UN (续)
外螺纹/内螺纹
标准参照: ANSI B1.1.74公差等级: 2A/2B级
细牙螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 6.0mm | 80 | 6.0E80UNTMF... | 6.0180UNTMF... | 9.84 | 16 | ||
| 72 | 6.0E72UNTMF... | 6.0172UNTMF... | 9.53 | 14 | |||
| 64 | 6.0E64UNTMF... | 6.0164UNTMF.. | 9.13 | 12 | |||
| 56 | 6.0E56UNTMF... | 6.0156UNTMF... | 9.53 | 11 | |||
| 48 | 6.0E48UNTMF... | 9.00 | 9 | ||||
| 44 | 6.0E44UNTM.F... | 8.66 | 8 | ||||
| 40 | 6.0E40UNTMF... | 8.26 | 7 | ||||
| 36 | 6.0E36UNTMF... | 9.17 | 7 | ||||
| 32 | 6.0E32UNTMF... | 8.73 | 6 | ||||
| 1/4" | 80 | 2E80UNTM2F... | 2I80UNTM2F... | 9.84 | 16 | ||
| 72 | 2E72UNTM2F... | 2I72UNTM2F.. | 10.23 | 15 | |||
| 64 | 2E64UNTM2F... | 2I64UNTM2F... | 9.92 | 13 | |||
| 56 | 2E56UNTM2F.. | 2I56UNTM2F... | 9.53 | 11 | |||
| 48 | 2E48UNTM2F... | 10.05 | 10 | ||||
| 44 | 2E44UNTM2F... | 9.81 | 9 | ||||
| 40 | 2E40UNTM2F... | 9.53 | 8 | ||||
| 36 | 2E36UNTM2F... | 9.17 | 7 6 | ||||
| 32 80 | 2E32UNTM2F... 3E80UNTM2F.. | 3180UNTM2F... | 8.73 14.29 | 23 | |||
| 72 | 3E72UNTM2F... | 3I72UNTM2F... | 14.46 | 21 | |||
| 64 | 3E64UNTM2F... | 3I64UNTM2F... | 14.68 | 19 | |||
| 56 | 3E56UNTM2F... | 3I56UNTM2F... | 16 | ||||
| 48 | 3E48UNTM2F... | 14.06 14.29 | 14 | ||||
| 44 | 3E44UNTM2F... | 14.43 | 13 | ||||
| 40 | 3E40UNTM2F... | 14.61 | 12 | ||||
| 36 | 3E36UNTM2F... | 14.82 | 11 | ||||
| 32 | 3E32UNTM2F... | 13.49 | 9 | ||||
提示：完成螺纹加工需走两个螺旋插补轨迹。 细牙螺纹铣刀片完成范牙型螺纹。订货示例：6.0E80UNTMF VBX所有刀片有两个切削刃，除了MiniTM ( 1 0 . 6 . 0 \mathsf {mm } ) 只有一个切削刃。更多刀杆信息，请参阅282页。细牙螺纹细牙螺纹螺距较小，由于相邻齿的刀尖圆弧过小，因此细牙多齿螺纹刀片的制造非常困难。瓦格斯司设计开发的细牙多齿螺纹刀片其齿间距为两倍细牙螺距。重要提示！
• 所有细牙螺纹刀片为范围牙型（因加大刀尖圆弧所致)。
#
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | |||
| IC | Lmm | TPI | 外螺纹 | 内螺纹 | mm | 刀杆 | |
| 6.0mm | 10.4 | 24 | 6.0l24UNJTM... | 9.53 | 9 | ||
| 20 | 6.0120UNJTM... | 8.89 | 7 | ||||
| 18 | 6.0I18UNJTM... | 8.47 | 6 | ||||
| 16 | 6.0I16UNJTM... | 9.53 | 6 | ||||
| 1/4" | 24 | 2E24UNJTM2... | 2I24UNJTM2... | 9.53 | 9 | TMSH.2 | |
| 20 | 2E20UNJTM2... | 2I20UNJTM2... | 10.16 | 8 | |||
| 18 | 2I18UNJTM2... | 9.88 | 7 | ||||
| 16 | 2E16UNJTM2.. | 2I16UNJTM2... | 9.53 | 6 | |||
| 14 | 2E14UNJTM2... | 2I14UNJTM2... | 9.07 | 5 | |||
| 3/8" | 24 | 3E24UNJTM2... | 3124UNJTM2... | 14.82 | 14 | TMSH.-.3 | |
| 20 | 3E20UNJTM2... | 3120UNJTM2... | 13.97 | 11 | |||
| 18 | 3E18UNJTM2... | 3I18UNJTM2... | 14.11 | 10 | |||
| 16 | 3E16UNJTM2... | 3I16UNJTM2... | 14.29 | 9 | |||
| 14 | 3E14UNJTM2... | 3I14UNJTM2... | 14.51 | 8 | |||
| 13 | 3E13UNJTM2... | 13.68 | 7 | ||||
| 12 | 3E12UNJTM2... | 3I12UNJTM2... | 14.82 | 7 | |||
| 5E16UNJTM2... | 5I16UNJTM2... | 25.40 | 16 | ||||
| 5/8" | 27 | 16 12 | 5E12UNJTM2... | 5I12UNJTM2... | 25.40 | 12 | TMC..-5 TMSH..-5 |
| 11 | 5E11UNJTM2... | 5I11UNJTM2... | 25.40 | 11 | |||
所有刀片有两个切削刃，除了MiniTM { 1 } \mathsf { C } 6 . 0 \mathsf {mm } ^ { \prime } ) 只有一个切削刃。更多刀杆信息，请参阅282页。
外螺纹/内螺纹
BSW 标准参照: B.S.84:1956, DIN 259, ISO228/1:1982
BSP 标准参照: B.S.2779:1956
公差等级: BSW-中等A级, BSP-中等
标准型螺纹铣刀
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | 刀杆 | |
| 10.4 | 28 | 6.0El28WTM... | 9.07 | 10 | TMMC..-6.0 | |
| 26 | 6.0EI26WTM... | 8.79 | 9 | |||
| 24 | 6.0E124WTM... | 9.53 | 9 | |||
| 20 | 6.0E120WTM... | 8.89 | 7 | |||
| 6.0EI19WTM.. | 9.36 | 7 | ||||
| 1/4" | 11 | 19 28 | 2EI28WTM2... | 9.98 | 11 | TMSH.2 |
| 26 | 2E126WTM2... | 9.77 | 10 | |||
| 2E124WTM..... | 953 | |||||
| 2420 | 98 | |||||
| 19 | 2EI19WTM2... | 9.36 | 7 | |||
| 14 | 2EI14WTM2... | 9.07 | 5 | |||
| 3/8" | 26 | 3EI26WTM2... | 14.65 | 15 | TMC..-3 | |
| 24 | 3EI24WTM2... | 14.82 | 14 | |||
| 20 | 3EI20WTM2... | 13.97 | 11 | |||
| 19 | 3EI19WTM2... | 14.71 | 11 | |||
| 18 | 3EI18WTM2... | 14.11 | 10 | |||
| 3EI16WTM2... | 14.29 | 9 | ||||
| 16 14 | 3EI14WTM2... | 14.51 | 8 | |||
| 12 | 3EI12WTM2... | 14.82 | 7 | |||
| 11 | 3EI11WTM2... | 13.85 | 6 | |||
| 3/8"B | 24 | 3BEI24WTM2... | 21.17 | 20 | TMSH.3B | |
| 20 | 3BEI20WTM2... | 21.59 | 17 | |||
| 19 | 3BEI19WTM2... | 21.39 | 16 | |||
| 3BE18WTM.... | 21.17 | 1513 | ||||
| 1816 | ||||||
| 14 | 3BEI14WTM2... | 21.77 | 12 | |||
| 12 | 3BEI12WTM2... | 21.17 | 10 | |||
| 11 | 3BEI11WTM2... | 20.78 | 9 | |||
| 5/8" | 16 | 5EI16WTM2... | 25.40 | 16 | TMSH.55 | |
| 14 | 5EI14WTM2... 5EI12WTM2... | 25.40 | 14 | |||
| 12 | 23.28 | 11 | ||||
| 11 | 5EI11WTM2.. | 23.09 | 10 | |||
| 10 9 | 5EI10WTM2... 5EI9WTM2... | 25.40 22.58 | 10 8 | |||
| 8 | 5E18WTM2... | 22.23 | 7 | |||
| 7 | 5EI7WTM2... | 21.77 | 6 | |||
| 6 | 5E16WTM2... | 21.17 | 5 | |||
| 11 | 6BEI11WTM2... | 34.64 | 15 | |||
| 3/4"B | 38.5 | 6BEI6WTM2... | 33.87 | 8 | TMC..-6B TMSH..-6B | |
| 6 5 | ||||||
| 6BEI5WTM2... | 30.48 | 6 | ||||
| 4.5 | 6BEI4.5WTM2... | 33.87 | ||||
| 6 |
所有刀片有两个切削刃，除了MiniTM ( | \mathsf { C } 6 . 0 \mathsf {mm } ) 只含有一个刀刃。更多刀杆信息，请参阅282页。
惠氏螺纹-仅用于BSW螺纹（续）
粗牙螺纹铣刀
标准参照: B.S.84:1956, DIN259, ISO228/1:1982公差等级：中等A级
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| Inch | IC | Lmm | 内螺纹 | mm | 刀杆 | mm | ||
| 7/16"-18 | 6.0I18WTM028/035... | 1 | 8.47 | 6 | TMMC12-6.0 | 9.3-14.2 | ||
| 7/16"-18 | 6.0I18WTM028/035... | 1 | 8.47 | 6 | TMMC20-6.0 | 9.3-14.2 | ||
| 7/16"-26 | 6.0mm | 10.4 | 6.0126WTM028/036... | 1 | 8.79 | 9 | TMMC12-6.0 | 9.8-10.5 |
| 7/16"-26 | 6.0126WTM028/036... | 1 | 8.79 | 9 | TMMC20-6.0 | 9.8-10.5 | ||
| 1/2"-16 | 1/4" | 11 | 2I16WTM028/051... | 1 | 9.53 | 6 | TMC20-2-124/005 | 10.6-12.2 |
| 1/2"-20 | 6.0mm | 10.4 | 6.0120WTM028/037.. | 1 | 8.89 | 7 | TMMC12-6.0 | 11.0-11.4 |
| 1/2"-20 | 6.0120WTM028/037... | 1 | 8.89 | 7 | TMMC20-6.0 | 11.0-11.4 | ||
| 9/16"-16 | 1/4" | 11 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC12-2 | 12.2-18.5 |
| 9/16"-16 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC20-2 | 12.2-18.5 | ||
| 5/8"-14 | 2I14WTM028/039... | 1 | 9.07 | 5 | TMC20-2-124/006 | 13.5-19.0 | ||
| 11/16"-14 | 2I14WTM028/039... | 1 | 9.07 | 5 | TMC20-2-124/006 | 13.5-19.0 | ||
| 11/16"-16 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC12-2 | 12.2-18.5 | ||
| 11/16"-16 | 3/8″ | 16 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC20-2 | 12.2-18.5 |
| 3/4"-12 | 3I12WTM028/040... | 1 | 14.82 | 7 | TMC16-3-124/001 | 16.3-17.9 | ||
| 3/4"-16 | 1/4" | 11 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC12-2 | 12.2-18.5 |
| 3/4"-16 | 2I16WTM028/038... | 2 | 9.53 | 6 | TMC20-2 | 12.2-18.5 | ||
| 13/16"-12 | 3/8" | 16 | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC16-3 | 17.9-21.0 |
| 7/8"-9 1/2″ | 4I9WTM028/042... | 1 | 16.93 | 6 | TMC25-4-124/002 | 18.6-32.5 | ||
| 7/8"-11 | 22 16 | 4I11WTM028/043... | 1 | 18.47 | 8 | TMC25-4-124/002 | 19.2-22.0 | |
| 15/16"-12 3/8″ | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 | ||
| 1"-8 | 1/2" | 22 | 4I8WTM028/044... | 1 | 15.88 | 5 | TMC25-4-124/002 | 21.3-26.0 |
| 1"-10 | 4I10WTM028/045... | 1 | 17.78 | 7 | TMC25-4-124/002 | 22.1-31.6 | ||
| 1"-12 | 3/8" | 16 | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 |
| 1 1/16"-12 | 3I12WTM028/041.. | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 | ||
| 1 1/8"-7 | 5/8" 1/2″ | 27 | 5I7WTM028/046... | 1 | 21.77 | 6 | TMC25-5-124/008 | 23.9-27.1 |
| 11/8"-9 | 22 | 4I9WTM028/042... | 1 | 16.93 | 6 | TMC25-4-124/002 | 18.6-32.5 | |
| 1 1/8"-12 | 3/8″ | 16 | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 |
| 1 3/16"-8 | 5/8″ | 27 | 5I8WTM028/047... | 2 | 22.23 | 7 | TMC25-5-124/004 | 26.0-32.4 |
| 1 3/16"-12 | 3/8″ | 16 | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 |
| 1 1/4"-7 | 5/8″ | 27 | 5I7WTM028/048... | 2 | 21.77 | 6 | TMC25-5-124/004 | 21.7-35.9 |
| 1 1/4"-9 | 1/2″ | 22 | 4I9WTM028/042... | 1 | 16.93 | 6 | TMC25-4-124/002 | 18.6-32.5 |
| 1 1/4"-12 3/8″ | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 | ||
| 1 5/16"-6 | 5/8" | 16 | 5I6WTM028/049... | 2 | 21.17 | 5 | TMC25-5-124/004 | 27.9-32.6 |
| 1 5/16"-8 | 27 | 7 | TMC25-5-124/004 | 26.0-32.4 | ||||
| 5I8WTM028/047... | 2 | 22.23 | ||||||
惠氏螺纹-仅用于BSW螺纹（续）
内螺纹
粗牙 TM
标准参照: B.S.84:1956, DIN259, ISO228/1:1982公差等级：中等A级
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| IC | Lmm | 内螺纹 | mm | 刀杆 | mm | |||
| 1 5/16"-12 | 3/8″ | 16 | 3I12WTM028/041... | 2 | 14.82 | 7 | TMC20-3 | 21.0-30.6 |
| 13/8-8 | 5I8WTM028/047... | 2 | 22.23 | 7 | TMC25-5-124/004 | 26.0-32.4 | ||
| 13/8"-6 | 5I6WTM028/049... | 2 | 21.17 | 5 | TMC25-5-124/004 | 27.9-32.6 | ||
| 1 3/8"-12 | 5I12WTM028/050... | 2 | 23.28 | 11 | TMC25-5 | 32.2-34.6 | ||
| 1.4-6 | 5I6WTM028/049... | 2 | 21.17 | 5 | TMC25-5-124/004 | 27.9-32.6 | ||
| 1.4-8 | 5I8WTM028/047... | 2 | 22.23 | 7 | TMC25-5-124/004 | 26.0-32.4 | ||
| 1.4-12 | 5I12WTM028/050... | 2 | 23.28 | 11 | TMC25-5 | 32.2-34.6 | ||
| 1 7/16"-6 | 5I6WTM028/049... | 2 | 21.17 | 5 | TMC25-5-124/004 | 27.9-32.6 | ||
| 1 7/16"-8 | 5I8WTM028/047... | 2 | 22.23 | 7 | TMC25-5 | 32.4-39.0 | ||
| 1 7/16"-12 | 5I12WTM028/050... | 2 | 23.28 | 11 | TMC25-5 | 32.2-34.6 | ||
| 1 1/2"-6 | 5I6WTM028/049... | 2 | 21.17 | 5 | TMC25-5-124/004 | 27.9-32.7 | ||
| 11/2" -8 | 5I8WTM028/047... | 2 | 22.23 | 7 | TMC25-5 | |||
| 1.6-6 | 5I6WTM028/049... | 2 | 21.17 | TMC25-5 | 32.6-38.5 | |||
| 1.6-8 | 5I8WTM028/047... | 2 | 22.23 | TMC25-5 | 32.4-39.0 | |||
| 1 5/8"-8 | 5I8WTM028/047... | 2 | 22.23 | TMC25-5 | 32.4-39.0 | |||
| 15/8"-6 | 516WTM028/049... | 2 | 21.17 | TMC25-5 | 32.6-38.5 | |||
| 13/4"-7 | 5I7WTM028/048... | 2 | 21.77 | 6 | TMC25-5 | 39.8-42.0 | ||
| 17/8"-6 | 516WTM028/049... | 21.17 | 5 | TMC32-5 | 42.2-45.0 | |||
| 1.9-6 | 516WTM028/049... | 21.17 | 5 | TMC32-5 | 42.2-45.0 | |||
惠氏螺纹-仅用于BSW螺纹（续）
TMO刀杆的标准TM刀片
| 刀片尺寸 | 螺距 | 订货代码 | ECL | ||
| IC | Lmm | TPI | 外部的 | 刀杆 | mm |
| 1/4" | 11 | 28 | 2EI28WTM2... | TMOC20-2-3 | 17.24 |
| 26 | 2El26WTM2... | TMOC20-2-5 | 18.56 | ||
| 24 | 2EI24WTM2... | TMOC20-2-2 | 17.99 | ||
| 20 | 2E120WTM2... | TMOC20-2-6 | 19.05 | ||
| 19 | 2EI19WTM2... | TMOC20-2-7 | 17.38 | ||
| 3/8" | 14 | 2EI14WTM2... | TMOC20-2-3 | 16.33 | |
| 26 | 3EI26WTM2... | TMOC20-3-2 | 27.35 | ||
| 26 | 3El26WTM2... | TMOC20-3-6 | 26.38 | ||
| 24 | 3EI24WTM2... | TMOC20-3-7 | 28.57 | ||
| 20 | 3EI20WTM2... | TMOC20-3-6 | 26.67 | ||
| 19 | 3EI19WTM2... | TMOC20-3-8 | 28.07 | ||
| 18 | 3EI18WTM2... | TMOC20-3-6 | 26.81 | ||
| 16 14 | 3EI16WTM2... | TMOC20-3-6 | 26.99 | ||
| 12 | 3EI14WTM2... | TMOC20-3-6 | 27.21 | ||
| 3EI12WTM2... | TMOC20-3-6 | 27.52 | |||
| 11 | 3EI11WTM2... | TMOC20-3-9 | 27.71 | ||
| 27 | 16 | 5EI16WTM2... 5EI14WTM2... | TMOC25-5-3 | 47.63 | |
| 14 14 | 5EI14WTM2... | TMOC25-5-1 | 50.80 | ||
| 12 | 5EI12WTM2... | TMOC25-5-4 | 47.17 | ||
| 11 | 5EI11WTM2... | TMOC25-5-2 | 44.45 | ||
| 10 | 5EI10WTM2... | TMOC25-5-6 TMOC25-5-7 | 46.18 | ||
| 9 | 5EI9WTM2.. | TMOC25-5-8 | 45.72 45.16 | ||
| 8 | 5EI8WTM2... | TMOC25-5-9 | 44.45 | ||
| 7 | 5EI7WTM2... | TMOC25-5-4 | 43.54 | ||
| 6 | 5EI6WTM2... | TMOC25-5-11 | 42.33 | ||
外螺纹/内螺纹
标准参照: USAS B2.1:1968公差等级: 标准型 NPT
标准型螺纹铣刀
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | 刀杆 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | RH | LH | |
| 3/8" | 16 | 18 | 3E18NPT-TM2...* | 14.11 | 10 | TMNC.-3 | TMNC..-3LH |
| 14 | 3EI14NPT-TM2... | 14.51 | 8 | ||||
| 11.5 | 3EI11.5NPT-TM2.. | 13.25 | 6 | ||||
| 3/8"B | 22 | 14 | 3BEI14NPT-TM2... | 21.77 | 12 | BTMNC..-3B | BTMNC..-3BLH |
| 11.5 | 3BEI11.5NPT-TM.2.** | 19.88 | 9 | ||||
| 5/8″ | 27 | 11.5 | 5EI11.5NPT-TM2... | 24.30 | 11 | TM.C..-5 | TM.C.-5LH |
| 8 | 5EI8NPT-TM2... | 22.23 | 7 | ||||
| 3/4"B | 38.5 | 11.5 | 6BEI11.5NPT-TM2. | 35.34 | 16 | TMNC...-.5 TMC..-6B | TMNC.-5LH TMC..-6BLH |
| 8 | 6BEI8NPT-TM2... | 31.75 | 10 | ||||
\* 仅用于外螺纹加工使用刃口标记为“L”的刀片时，请选用左手刀杆。更多刀杆信息，请参阅286页。\*\* 单面刀片 - 仅用于右手。
NPT
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | ||
| Inch | IC | Lmm | 内螺纹 | mm | 刀杆 | ||
| 1/4"-18 | 11 | 2I18NPT-TM028/074... 1 | 9.88 | 7 | TMC20-2-124/009 | ||
| 3/8"-18 | 1/4" | 2I18NPT-TM028/074.. | 1 | 9.88 | 7 | TMC20-2-124/009 | |
NPTF(干式密封螺纹)
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | 刀杆 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | RH | LH | |
| 3/8″ | 14 | 3EI14NPTFTM2... | 14.51 | 8 | |||
| 3/8"B | 16 22 | 11.5 | 3EI11.5NPTFTM2... | 13.25 | 6 | TMNC..-3 | TMNC..-3LH |
| 14 | 3BEI14NPTFTM2... | 21.77 | 12 | ||||
| 11.5 | 3BEI11.5NPTFTM2... | 19.88 | 9 | BTMNC..-3B TM.C..-5 | BTMNC.-3BLH | ||
| 11.5 | 5EI11.5NPTFTM2... | 24.30 | 11 | ||||
| 5/8″ | 27 | 8 | 5EI8NPTFTM2... | 22.23 | 7 | TMNC..-5 | TM.C..-5LH TMNC..-5LH |
| 11.5 | |||||||
| 3/4"B | 38.5 | 6BEI11.5NPTFTM2... | 35.34 | 16 | TMC..-6B | TMC..-6BLH | |
| 8 | 6BEI8NPTFTM2... | 31.75 | 10 | ||||
使用刃口标记为“L”的刀片时，请选用左手刀杆。更多刀杆信息，请参阅286页。
NPTF(干式密封螺纹)
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | ||
| Inch | IC | Lmm | 内螺纹 | mm | 刀杆 | ||
| 1/4"-18 | 2I18NPTFTM028/078... | 9.88 | 7 | TMC20-2-124/009 | |||
| 3/8"-18 | 1/4" | 11 | 2I18NPTFTM028/078. | 1 1 | 9.88 | 7 | TMC20-2-124/009 |
更多刀杆信息，请参阅286页。
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | 螺纹公称尺寸 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | 刀杆 | ||
| 3/8″ | 16 | 14 | 3EI14NPSTM2... | 14.51 | 8 | 1/2″ | TMNC16-3 |
| 14 | 3EI14NPSTM2... | 14.51 | 8 | 3/4" | TMNC20-3 | ||
| 11.5 | 3EI11.5NPSTM2... | 13.25 | 6 | 1", 1 1/4" | TMNC20-3 | ||
| 3/8"B | 22 | 11.5 | 3BEI11.5NPSTM2...* | 19.88 | 9 | 1", 1 1/4" | BTMNC20-3B |
| 5/8" | 27 | 11.5 | 5EI11.5NPSTM2... | 24.30 | 11 | 1 1/2",2" | TMC25-5 |
| 8 | 5EI8NPSTM2... | 22.23 | 7 | 2 1/2" & larger | TMC32-5 |
\* 单一切刃刀所有刀片有两个切削刃。更多刀杆信息，请参阅282页。
BSPT
外螺纹/内螺纹
标准参照: B.S. 21:1985公差等级: 标准型 BSPT
标准型螺纹铣刀
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | 刀杆 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | RH | LH | |
| 1/4" | 11 | 19 | 2EI19BSPT-TM2... | 9.36 | 7 | TMC..-2 | TMC..-2LH |
| 3/8″ | 16 | 14 | 3EI14BSPT-TM2.... | 14.51 | 8 | TMNC..-3 | TMNC..-3LH |
| 11 | 3EI11BSPT-TM2... | 13.85 | 6 | ||||
| 5/8″ | 27 | 11 | 5EI11BSPT-TM2.. | 23.09 | 10 | TMC..-5 | TMC..-5LH |
使用刃口标记为“L”的刀片时，请选用左手刀杆。更多刀杆信息，请参阅282页。
Pg
标准型螺纹铣刀
公差等级：标准型
标准型螺纹铣刀
| 刀片尺寸 | 螺距 | 订货代码 | Le | 齿数 | 螺纹公称尺寸 | ||
| IC | Lmm | TPI | 外螺纹/内螺纹 | mm | 刀杆 | ||
| 6.0mm | 10.4 | 20 | 6.0EI20PGTM... | 8.99 | 7 | Pg7 | TMMC..-6.0 |
| 1/4" | 20 | 2EI20PGTM2... | 10.16 | 8 | Pg7 | TMC..-2 TMSH..-2 | |
| 11 | 18 | 2EI18PGTM2... | 9.88 | 7 | Pg9, Pg11, Pg13.5,Pg16 | ||
| 16 | 2EI16PGTM2... | 9.53 | 6 | Pg21, Pg29, Pg36, Pg42, Pg48 | |||
| 3/8" | 20 | 3EI20PGTM2... | 13.97 | 11 | Pg7 | TMSH.3 | |
| 16 | 18 | 3EI18PGTM2... | 14.11 | 10 | Pg9, Pg11, Pg13.5, Pg16 | ||
| 16 | 3EI16PGTM2... | 14.29 | 9 | Pg21, Pg29, Pg36, Pg42,Pg48 | |||
| 5/8" | 27 | 16 | 5EI16PGTM2... | 25.40 | 16 | Pg21, Pg29, Pg36, Pg42, Pg48 | TMC.-5, TMSH..-5 |
内螺纹
标准参照: ANSI B1/5:1988公差等级: 3G
粗牙螺纹铣刀
粗牙螺纹铣刀
| 螺纹 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | |||
| Inch | IC Lmm | 内螺纹 | mm | 刀杆 | mm | |||
| 1/2"-16 | 6.0mm | 10.4 | 6.0I16ACMETM028/052... | 1 | 7.94 | 5 | TMMC12-6.0 | 11.1 |
| 1/2"-16 | 6.0I16ACMETM028/052.. | 1 | 7.94 | 5 | TMMC20-6.0 | 11.1 | ||
| 5/8"-16 | 11 | 2I16ACMETM028/05. | 2 | 9.53 | 6 | TMC12-2 | 14.2 | |
| 5/8"-16 | 2I16ACMETM028/053... | 2 | 9.53 | 6 | TMC20-2 | 14.2 | ||
| 5/8-14 | 2I14ACMETM028/054... | 1 | 9.07 | 5 | TMC20-2-124/005 | 14.0 | ||
| 3/4"-16 | 2I16ACMETM028/055... | 2 | 9.53 | 6 | TMC12-2 | 17.4 | ||
| 3/4"-16 | 2I16ACMETM028/05.. | 2 | 9.53 | 6 | TMC20-2 | 17.4 | ||
| 3/4"-14 | 2I14ACMETM028/08.. | 1 | 9.07 | 5 | TMC20-2-124/006 | 17.2 | ||
| 3/4"-12 | 2I12ACMETM028/056... | 1 | 8.47 | 4 | TMC20-2-124/006 | 16.9 | ||
| 7/8"-14 | 3/8″ 16 | 3I14ACMETM028/05... | 2 | 14.51 | 8 | TMNC16-3 | 20.4 | |
| 7/8"-12 | 1/4" | 11 | 2I12ACMETM028/058. | 1 | 8.47 | 4 | TMC20-2-124/006 | 20.1 |
| 3I14ACMETM028/05. | 2 | 14.51 | 8 | TMC16-3 | 23.5 | |||
| 1"-14 1"-12 | 3/8" | 16 | 3I12ACMETM028/060... | 2 | 14.82 | 7 | TMNC16-3 | 23.2 |
| 1"-10 | 4I10ACMETM028/061... | 1 | 17.78 | 7 | TMC25-4-124/002 | 22.8 | ||
| 1"-8 | 1/2″ | 22 16 | 4I8ACMETM028/062.. | 1 | 19.05 | 6 | TMC25-4-124/002 | 22.2 |
| 1 1/8"-12 3/8" | 3I12ACMETM028/060... | 2 | 14.82 | 7 | TMC16-3 | 26.4 | ||
| 1 1/8"-10 | 1/2″ | 22 | 4I10ACMETM028/084. | 1 | 17.78 | 7 | TMC25-4-124/007 | 26.0 |
| 1 1/8"-8 | 4I8ACMETM028/063... | 1 | 19.05 | 6 | TMC25-4-124/002 | 25.4-28.5 | ||
| 1 1/4"-12 | 3/8" | 16 | 3I12ACMETM028/060... | 2 | 14.82 | 7 | TMC20-3 | 29.6 |
| 1 1/4"-10 | 5/8" 1/2″ | 27 | 5I10ACMETM.028/06*4.. | 2 | 22.86 | 9 | TMC25-5-124/004 | 29.2 |
| 1 1/4"-8 | 22 | 4I8ACMETM028/063.. | 1 | 19.05 | 6 | TMC25-4-124/002 | 25.4-28.5 | |
| 13/8"-10 | 5I10ACMETM028/06.. | 2 | 22.86 | 9 | TMC25-5-124/004 | 32.3 | ||
| 13/8"-8 | 5I8ACMETM028/066.. | 2 | 22.23 | 7 | TMC25-5-124/004 | 31.7 | ||
| 13/8"-6 | 5I6ACMETM028/067... 5I10ACMETM028/068... | 1 | 21.17 | 5 | TMC25-5-124/008 | 30.6 | ||
| 1 1/2"-10 | 5I8ACMETM028/069.. | 2 | 22.86 | 9 | TMC25-5 | 35.5 | ||
| 11/2"-8 | 2 | 22.23 | 7 | TMC25-5-124/004 | 34.9 | |||
| 11/2"-6 | 5I6ACMETM028/070.. | 2 | 21.17 | 5 | TMC25-5-124/004 | 33.8 | ||
| 13/4"-10 | 5I10ACMETM028/06. 5I8ACMETM028/069.. | 2 | 22.86 | 9 | TMC32-5 | 41.9 | ||
| 13/4"-8 | 2 | 22.23 | 7 | TMC25-5 | 41.2 | |||
| 13/4"-6 | 5/8″ 27 | 5I6ACMETM028/070.. | 2 | 21.17 | 5 | TMC25-5 | 40.2 | |
| 13/4"-5 | 5I5ACMETM028/071... | 2 | 20.32 | 4 | TMC25-5-124/004 | 39.3 | ||
| 2"-8 | 5I8ACMETM028/06.. | 2 | 22.23 | 7 | TMC32-5 | 47.6 | ||
| 2"-6 | 5I6ACMETM028/072.. | 2 | 21.17 | 5 | TMC25-5 | 46.5 | ||
| 2"-5 | 5I5ACMETM028/071.. | 2 | 20.32 | 4 | TMC25-5 | 45.7 | ||
| 2 1/4"-6 | 5I6ACMETM028/072.. | 2 | 21.17 | 5 | TMC32-5 | 52.9 | ||
| 2 1/4"-5 | 5I5ACMETM028/07... | 2 | 20.32 | 4 | TMC25-5 | 52.0 | ||
| 2 1/2"-5 | 5I5ACMETM028/07... | 2 | 20.32 | 4 | TMC32-5 | 58.4 | ||
梯形螺纹
内螺纹
标准参照: 梯形螺纹 DIN 103公差等级: 7e/7H
粗牙螺纹铣刀
粗牙螺纹铣刀
| 螺纹 | 刀片尺寸 | 订货代码 | 切削刃 | Le | 齿数 | 镗孔直径范围 | ||
| mm | IC | 内螺纹 | mm | 刀杆 | mm | |||
| TR16x2.0 | 1/4" | Lmm 11 | 2l2.0TRTM028/028.. | 1 | 10 | 5 | TMC20-2-124/006 | 14.0 |
| TR18x2.0 | 2I2.0TRTM028/029... | 1 | 10 | 5 | TMC20-2-124/006 | 16.0-18.0 | ||
| TR20x2.0 | 1/2″ | 2I2.0TRTM028/029... | 1 | 10 | 5 | TMC20-2-124/006 | 16.0-18.0 | |
| TR24x3.0 | 41l3.0TRTM028/030... | 1 | 18 | 6 | TMC25-4-124/002 | 21.0 | ||
| TR26x3.0 | 4l3.0TRTM028/031... | 1 | 18 | 6 | TMC25-4-124/002 | 23.0-27.0 | ||
| TR28x3.0 | 4l3.0TRTM028/031... | 1 | 18 | 6 | TMC25-4-124/002 | 23.0-27.0 | ||
| TR30x3.0 | 4I3.0TRTM028/031... | 1 | 18 | 6 | TMC25-4-124/002 | 23.0-27.0 | ||
| TR32x3.0 | 4l3.0TRTM028/03.. | 1 | 18 | 6 | TMC25-4-124/007 | 29.0-33.0 | ||
| TR34x3.0 | 4I3.0TRTM028/032... | 1 | 18 | 6 | TMC25-4-124/007 | 29.0-33.0 | ||
| TR36x3.0 | 4I3.0TRTM028/032... | 1 | 18 | 6 | TMC25-4-124/007 | 29.0-33.0 | ||
| TR38x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC25-5-124/004 | 35.0-39.0 | ||
| TR40x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC25-5-124/004 | 35.0-39.0 | ||
| TR42x3.0 | 5I3.0TRTM028/033... | 2 | 24 | 8 | TMC25-5-124/004 | 35.0-39.0 | ||
| TR44x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC25-5 | 41.0-45.0 | ||
| TR46x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC25-5 | 41.0-45.0 | ||
| TR48x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC25-5 | 41.0-45.0 | ||
| TR50x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC32-5 | 47.0-57.0 | ||
| TR52x3.0 | 5I3.0TRTM028/033... | 2 | 24 | 8 | TMC32-5 | 47.0-57.0 | ||
| TR55x3.0 | 5I3.0TRTM028/033.. | 2 | 24 | 8 | TMC32-5 | 47.0-57.0 | ||
| TR60x3.0 | 5I3.0TRTM028/03... | 2 | 24 | 8 | TMC32-5 | 47.0-57.0 | ||
| TR65x4.0 | 514.0TRTM028/03.. | 2 | 24 | 6 | TMC32-5 | 61.0-106.0 | ||
| TR70x4.0 | 514.0TRTM028/034.. | 2 | 24 | 6 | TMC32-5 | 61.0-106.0 | ||
| TR75x4.0 | 514.0TRTM028/034... | 2 | 24 | 6 | TMC32-5 61.0-106.0 | |||
| TR80x4.0 | 514.0TRTM028/03... | 2 | 24 | 6 | TMC32-5 61.0-106.0 | |||
| TR85x4.0 | 514.0TRTM028/034.. | 2 | 24 6 | TMC32-5 | 61.0-106.0 | |||
| TR90x4.0 | 514.0TRTM028/034.. | 2 | 24 | 6 TMC32-5 | 61.0-106.0 | |||
| TR95x4.0 | 514.0TRTM028/034.. | 2 | 24 | 6 TMC32-5 | 61.0-106.0 | |||
| TR100x4.0 | 514.0TRTM028/034.. | 2 | 24 | 6 | TMC32-5 61.0-106.0 61.0-106.0 | |||
| TR105x4.0 | 514.0TRTM028/034. | 2 | 24 | 6 | TMC32-5 | |||
| TR110x4.0 | 514.0TRTM028/03. | 2 | 24 | 6 | TMC32-5 61.0-106.0 | |||
外螺纹和内螺纹刀杆系列
| TM标准型 | |||||||
| 刀片尺寸 | 订货代码 | 尺寸mm | 一 | ||||
| IC | L | L1 | D | D1 | D2 | 刀片螺钉 Torx扳手 | |
| 6.0mm | TMMC12-6.0 | 69.0 | 12.0 | 12 | 6.8 | SN7T | K7T |
| TMMC20-6.0 | 84.0 | 17.0 | 20 | 6.8 | 9.0 | ||
| 1/4" | TMC12-2 | 70.0 | 12.0 | 12 | 8.9 | 11.5 | SN2TM K2T |
| TMC20-2 | 85.0 | 20.0 | 20 | 8.9 | 11.5 | ||
| TMC20-2LH | 85.0 | 20.0 | 20 | 8.9 | 11.5 | ||
| 3/8″ | TMC16-3 | 90.0 | 22.0 | 16 | 13.6 | 17.0 | K3T |
| TMC20-3 | 95.0 | 43.0 | 20 | 16.6 | 20.0 | ||
| 3/8"B | BTMC16-3B | 79.5 | 29.0 | 16 | 13.5 | 17.0 | SN3TM |
| BTMC20-3B | 81.5 | 29.0 | 20 | 15.5 | 19.0 | ||
| BTMC25-3B | 92.3 | 30.0 | 25 | 15.5 | 19.0 | ||
| BTMWC25-3B | 90.8 | 30.0 | 25 | 18.5 | 22.0 | K3T | |
| 5/8" | TMC25-5 | 110.0 | 52.0 | 25 | 24.0 | 30.0 | K5T |
| TMC25-5LH | 110.0 | 52.0 | 25 | 24.0 | 30.0 | ||
| TMC32-5 | 120.0 | 58.0 | 32 | 31.0 | 37.0 | ||
| 3/4"B | TMC32-6B | 115.0 | 53.0 | 32 | 27.0 | 35.0 | SM7T K30T |
| TMC40-6B | 135.0 | 63.0 | 40 | 38.0 | 46.0 | ||
| 标准型内螺纹刀杆 | |||||||||||
| 刀杆 | ISO粗牙 ISO细牙 | UNC | 最小螺纹直径 | ||||||||
| TMMC12-60 | D2 9.0 | M14x1.75:M12x1.0;14x15 | UN/UNF/UNEF/UNS | UNJ UNF | |||||||
| TMC2-2L | 11.5 | M15x1.0; M16x1.5 | 2UNF | 6-8UN6-24UNF: | |||||||
| TMC16-3 | 17.0 | M20x1.0; M22x1.5; M24x2.0 | 1- | ||||||||
| TMC20-3 | 20.0 | M24x1.0; M25x1.5; M27×2.0 | 7/8-32UN； 15/6-28UN: 1-24UNS; 15/16-20UNEF:1-18UNS; 1-16UNS; 11/8-14UNS; 1/6-12UN | 15/g-24 UNJ: 15/16-20UNJEF; 11/16-18UNJEF; 1-16UNJ; 15/8-14UNJ; 11/16-12UNJ | |||||||
| BTMC16-3B | 17.0 | M20x1.0; M22x1.5; M24x2.0 | UNU | ||||||||
| BTMC20-3B | 19.0 | M22x1.0; M24x1.5; M25x2.0 | 1-2UNUU | ||||||||
| BTMWC25-3B | 22.0 M27x1.5 30.0 | M25x1.0; M30x2 | 1-24UUEFUF | ||||||||
| TMC5 | M35x4.5:M42x2.0:M48.0 | 13/4-5 | 17/16-16UNJ; 1/z-12UNJF | ||||||||
| 1 | 1/6-16UNJ; 13/4-12UNJ | ||||||||||
| TMC32-5 TMC32-6B | 37.0 35.0 M64x6.0 | M515:M45x2.0:M50x3.0; M54.:M42×20:M5835. | 2-454 | 21/4-6UN | |||||||
| TMC40-6B | 46.0 M64x6.0 | M52X1.5:M520:.M6030 | 21/2-4 | 23/8-6UN | |||||||
| BSP | BSPT | PG | NPS | 梯形螺纹 | ACME | ||||||
| D2 | BSW/BSF 1/z-20BSW; | NPT | NPTF | PG7 | 1/2-16 | ||||||
| TMMC12-6.0 | 9.0 | W6-26BSF: | 1/4-19 | 3/8-19 | PG9; PG21 | 5/-16; | |||||
| TMC2L | 11.5 17.0 | 76-20BSW | 3/8-19; /2-14 | 1/2-14; 1-11.5 | 1-14; 1/8-12 | ||||||
| TMC16-3 | -141 | PG12.5: | |||||||||
| TMC20-3 | 20.0 | 7/8-16BSW; | 3/4-14; 1-11 | PG16: | 1-145 | 114-12 | |||||
| BTMC16-3B | 17.0 | 76-20BSW 11-208W 1-168S | %-14 3/4-14; 1-11 | 1-11.5 1-11.5 | |||||||
| BTMC20-3B BTMWC25-3B | 19.0 22.0 | 1/6-20BSW; 1/8-16BSW | -14: | 1-11.5 | |||||||
| TNC5 | 30.0 | 1/8-11 1/4-11 | 1/4-11.5 | 1/4-11.5 | PG29 | 14-1-5: | TR44-3.0 | 16-10-10-8 | |||
| 11/2-11.5 | |||||||||||
| TMC32-5 | 37.0 | 2.1-16SWW7-12BSW | 11/2-11 11/2-11 | 11/-11.5 | PG36 | 12-115 | TR5-40 | 10/4-102-85 | |||
| TMC32-6B | 35.0 | 24-6 BSF-3:58SF BSE | 1/2-11 | 21/2-8 | 21/2-8 | ||||||
外螺纹和内螺纹刀杆系列
| TM加长刀杆 | 配件 | |||||||
| 刀片尺寸 | 订货代码 | 尺寸mm | ||||||
| IC | L | L1 | D | D1 | D2 | 刀片螺钉 | Torx扳手 | |
| 1/4" | TMLC25-2 | 125.0 | 17.0 | 25 | 8.9 | 11.5 | SN2TM | K2T |
| 3/8″ | TMLC25-3 | 125.0 | 25.0 | 25 | 18.6 | 22.0 | ||
| BTMLC25-3 | 125.0 | 63.5 | 25 | 18.6 | 22.0 | SN3T | K3T | |
| 3/8"B | BTMLC20-3B | 96.5 | 44.0 | 20 | 15.5 | 19.0 | ||
| BTMLC25-3B | 125.0 | 63.5 | 25 | 18.6 | 22.0 | SN3T | K3T | |
| 5/8″ | TMLC25-5 | 150.0 | 92.0 | 25 | 24.0 | 30.0 | ||
| TMLC32-5 | 160.0 | 98.0 | 32 | 31.0 | 37.0 | SN5TM | K5T | |
| 3/4"B | TMLC40-6B | 165.0 | 93.0 | 40 | 38.0 | 46.0 | SM7T | K30T |
内螺纹加工TML刀杆
| 刀杆 | 最小螺纹直径 | |||||
| D2 | ISO粗牙 | ISO细牙 | UNC | UN/UNF/UNEF/UNS | UNJ | |
| TMLC25-2 | 11.5 | M15x1.0; M16x1.5 | -2UANF 96-8UNF6-24UNF | -2UU | ||
| TMC25--3 | 22.0 | M27x1.5 | M25x1.0;M30x2.0 | 1UN | 196-24UNJUUJ | |
| BTMLC20-3B | 19.0 | M22x1.0; M24x1.5; M25×2.0 | 7/8-24UNS；15/6-20UNEF;1-18UNS; 1-16UNS; 1-14UNS; 1-12UNF | |||
| BTMLC25-3B | 22.0 | M27x1.5 | M25x1.0; M30x2.0 | 1-24-U6UNEF2UNU | ||
| TMLC25-5 | 30.0 | M35x1.5; M39x2.0; M36x3.0; M36x4.0; M42x4.5; M48x5.0 | 13/4-5 | 162UN 15/-10UNS;17/6-8UN;15/-6UN | 17/6-16UNJ; 1/2-12UNJF | |
| TMLC32-5 | 37.0 | M45x1.5; M45x2.0; M50x3.0; M56x4.0 | 176-2UNUN 1/&-10UNS; 2-8 UN; 214-6UN | 111/6-16UNJ; 134-12UNJ | ||
| TMLC40-6B | 46.0 | M64x6.0 | M52x1.5; M55x2.0; M60x3.0; M60x4.0; M60x5.5 | 21/2-4 | 23/-6UN | |
| D2 | BSW/BSF | BSP | BSPT | NPT | NPTF | PG | NPS | 梯形螺纹 | ACME | |
| TMLC25-2 | 11.5 | 5%-26BSEF%-20BSW; | 3/-19; 1/2-14 | 3/8-19 | PG9; PG21 | |||||
| TML25-3 | 22.0 | 116-26BSSF 1/62D8SW: | /8-14; 1-11 | PG21 | 1-11.5 | |||||
| BTMLC20-3B | 19.0 | 146-2BSW -168SW | 3/4-14; 1-11 | 1-11.5 | ||||||
| BTMLC25-3B | 22.0 | 11/i6-20BSW; 1/8-16BSW | 7/8-14; 1-11 | PG21 | 1-11.5 | |||||
| TMLC25-5 | 30.0 | 13/4-7BSF; 17/8-6BSW | 1/4-11 | 1/4-11 | 1/4-11.5 | 1/4-11.5 | PG29 | 1/4-11:5 | TR44-3.0 | 116-0134-8 |
| TMLC32-5 | 37.0 | 17/-6BSW | 11/-11 | 11/2-11 | 11/-11.5 | 11/-11.5 | PG36 | 112-1145 | TR50-3.0: | 21/4-10 2-58 |
| TMLC40-6B | 46.0 | 3-5BSF; 3/-4.5BSF | 2-11 | 21-8 | 21/2-8 |
外螺纹和内螺纹刀杆系列
| 粗牙螺纹124/...-刀杆 | 配件 | |||||||
| 刀片尺寸 | 订货代码 | 尺寸mm | 一 | |||||
| IC | L | L1 | D | D1 | D2 | 刀片螺钉 | Torx扳手 | |
| 6.0mm | TMMC20-6.0-124/003 | 85 | 15.0 | 20 | 6.7 | 9.0 | SN7T | K7T |
| 1/4" | TMC20-2-124/005 | 77 | 15.5 | 20 | 7.4 | 10.0 | ||
| TMC20-2-124/006 | 77 | 15.5 | 20 | 9.0 | 12.0 | SN2TM | K2T | |
| TMC20-2-124/009 | 77 | 15.5 | 20 | 7.4 | 10.0 | |||
| 3/8″ | TMC16-3-124/001 | 91 | 20.5 | 16 | 12.2 | 15.5 | SN3TM | K3T |
| 1/2" | TMC25-4-124/002 | 88 | 30.0 | 25 | 13.4 | 18.0 | SN4TM | K4T |
| TMC25-4-124/007 | 98 | 40.0 | 25 | 16.0 | 20.0 | SA4TM | ||
| 5/8" | TMC25-5-124/004 | 98 | 40.0 | 25 | 19.0 | 25.0 | SA5TM | K5T |
| TMC25-5-124/008 | 98 | 40.0 | 25 | 16.4 | 22.0 | SN5TM | ||
粗牙螺纹124/…刀杆内螺纹加工范围
| 刀杆 | ||||||||||
| D2 | ISO粗牙 | ISO细牙 | UNC | 最小螺纹直径 UN/UNF/UNEF/UNS | UNJ | |||||
| TMMC20-6.0-124/003 | 9.0 | M12x1.75 M12x1.0; M22x1.5; M12x1.75 | 7/16-14 | 6-32UNF | 1/2-24UNS; 9/16-18UNF; | 18UNUEF:UUNJF;96 | ||||
| TMC20-2-124/005 | 10.0 | 1/2-13 | 5/g-12UN | |||||||
| TMC20-2-124/006 | 12.0 | 5/8-11 | ||||||||
| TMC20-2-124/009 | 10.0 | |||||||||
| TMC16-3-124/001 | 15.5 | M20x2.5 | M20x1.0; M22x1.5; M22x2.0 | 3/4-10 | 11/16-32UN;3/4-28UN;3/4-24UNS; 13/16-20UNEF;7/8-18UNS;7/8-16UNS; | 15/8-24UNJ; 13/16-20UNJEF; 11/16-18UNJEF; 13/16-16UNJ; | ||||
| TMC25-4-124/002 | 18.0 | M22×2.5: | 7/8-9; 11/8-7 | 7/8-14UNF; 7/8-12UN | 7/8-14UNJF; 7/8-12UNJ | |||||
| TMC25-4-124/007 | 20.0 | 1-8 | ||||||||
| TMC25-5-124/004 | 25.0 | M30x3.5 | M30x1.5; M33x2.0; M39x3.0; M56x4.0 | 13/8-6 | 14U | 13/16-16UNJ; 11/4-12UNJF | ||||
| TMC25-5-124/008 | 22.0 | 1/2-10UNS; 1/4-8UN | ||||||||
| D2 | BSW/BSF | BSP | BSPT NPT | NPTF | PG | NPS | 梯形螺纹 | ACME | ||
| TMMC20-6.0-124/003 | 9.0 | 7/16-26BSF; 7/16-18BSF; | 1/4-19 | PG7 | 1-145 | |||||
| TMC20-2-124/005 | 10.0 | 1/2-16BSF | 5/8-14 | |||||||
| TMC20-2-124/006 | 12.0 | 5/-14BSF | TR16-2 | 3/4-14; 3/4-12 | ||||||
| TMC20-2-124/009 | 10.0 | 1/4-18 | 1/4-18 | |||||||
| TMC16-3-124/001 | 15.5 | 3/4-12BSF | 1/2-14 | 3/4-14; 1-113/4-14; 1-11.534-14; 1-11.5 | PG13.5; PG21 | 1-11.5 | ||||
| TMC25-4-124/002 | 18.0 | 1-11SF: 1-1SF:/8-9BSW | TR24-3.0 | 1-10; 1-8 | ||||||
| TMC25-4-124/007 | 20.0 | TR32-3.0 | 11/-10 | |||||||
| TMC25-5-124/004 | 25.0 | 13/16-8BSW; 1/4-7BSW; | 1-11 | 1-11 14-11.5; | 1/4-11.5; 21/2-8 | PG21 | 1/4-11.5; | TR38-3.0 | 1/4-10-78 | |
| 15/16-6BSW | 21/2-8 | 21/2-8 | 13/4-5 | |||||||
| TMC25-5-124/008 | 22.0 | 1/8-7BSW | 13/8-6 | |||||||
外螺纹和内螺纹刀杆系列
锥度螺纹（NPT，NPTF，BSPT）TMN刀杆
| 刀片尺寸 | 订货代码 | 尺寸mm | 一 | ||||||
| IC | RH | *LH | L | L1 | D | D1 | D2 | ||
| 3/8" | TMNC16-3 | TMNC16-3LH | 90.0 | 22.0 | 16 | 12.5 | 15.5 | 刀片螺钉 SN3TM | Torx扳手 K3T |
| TMNC20-3 | TMNC20-3LH | 85.0 | 23.0 | 20 | 15.0 | 19.0 | |||
| 3/8"B | BTMNC16-3B | BTMNC16-3BLH | 79.5 | 29.0 | 16 | 13.5 | 17.0 | SN3TM | K3T |
| BTMNC20-3B | BTMNC20-3BLH | 81.5 | 29.0 | 20 | 15.5 | 19.0 | |||
| 5/8" | TMNC32-5 | TMNC32-5LH | 120.0 | 58.0 | 32 | 31.0 | 37.0 | SN5TM | K5T |
\* 使用刃口标记为“L”的刀片时，选用左手刀杆。
TMN刀杆内螺纹加工范围
| 刀杆 最小螺纹直径 | ||||
| D2 | ISO细牙 | UNC UN/UNF/UNEF/UNS | UNJ | |
| TMNC16-3 TMNC16-3LH | 15.5 | M20x1.0; M22x1.5; M22x2.0 | 11/6-32UN;3/4-28UN; 3/4-24UNS; 15/8-24UNJ;13/16-20UNJEF;116-18UNJEF; 1/6-2UNFU6U 13/16-16UNJ;7/8-14UNJF;7/8-12UNJ | |
| TMNC20-3LH | 19.0 | M22x1.0; M24x1.5; M25x2.0 | 1UNU | |
| BTMNC16-3B BTMNC16-3BLH | 17.0 | M20x1.0; M22x1.5; M24x2.0 | 7/8-24UNS;7/8-20UNEF;7/8-18UNS; /-16UNS; 1-14UNS; 13/16-12UN | |
| BTMNC20-3B BTMNC20-3BLH | 19.0 | M22x1.0; M24x1.5;M25x2.0 | 7/8-24UNS; 15/16-20UNEF: 1-18UNS; 1-16UNS; 1-14UNS; 1-12UNF | |
| TMNC32-5 TMNC32-5LH | 37.0 | M45x1.5; M45x2.0; M50x3.0; M56x4.0 | 15/8-24UNS; 111/16-20UN; 111/16-18UNEF; 11-1UN)EF:8UN:2UANS-12UN | |
| D2 | BSW/BSF | BSP | BSPT | NPT | NPTF | PG | NPS | 梯形螺纹 | ACME | |
| TMNC16-3LH | 15.5 | 13/16-16BSW | 1/2-14 | /-14; 1-11 | /-14; 1-11.5 | /-14; 1-11.5 | PG11 | 1/2-14; 1-11.5 | 7/8-14; 1-12 | |
| TMNC20-3LH | 19.0 | 3/4-14; 1-11 | 3/4-14; 1-11.5 | 3/4-14; 1-11.5 | PG21 | 3/4-14; 1-11.5 | ||||
| BTMNC16-3BLH | 17.0 | 13/6-12BSW -20BW-W-4 | 3/4-14; 1-11.5 | 3/4-14; 1-11.5 | 1-11.5 | |||||
| BTMNC20-3BLH | 19.0 | 1/6-12BSW 15/-20BSW;1-16BSW-4-11 | 3/4-14; 1-11.5 | 3/4-14; 1-11.5 | 1-11.5 | |||||
| TMNC32-5LH | 37.0 | 17/g-6BSW | 11/2-11 | 11/2-11 | 15-1.5 | 1-11.5, | PG36 | 12-11-5 |
外螺纹和内螺纹刀杆系列
双刀片TM2刀杆内螺纹加工范围
| 刀杆 最小螺纹直径 | ||||||||||||
| D2 (mm) | ISO细牙 | UNC | UN/UNF/UNEF/UNS | UNJ | BSW/BSF | BSP | BSPT | NPT | NPTF | PG | NPS | |
| TM2C20-2 | 17.0 | M22x1.5 | 3/4-32UN; 13/16-28UN; 7/8- 24UNS; 7/%-20UNEF; 7/8-18UNS; 7/-16UNS; 1-14UNS | 15/%-24UNJ;7/8-20UNJEF; 11/6-18UNJEF;7/8-16UNJ; 15/-14UNJ | 5/8-14 | PG16; PG21 | ||||||
| TM2C25-3 BTM2C25-3B | 26.0 | M32x1.5; M33x2.0 | 1/4-24UNS; 13/16-20UN; 194-14UNSF1V4-12UNEF | 15/-24UNJ; 13/16-20UNJ; 14-12UNJEF: 14-16UNJ; | 13/16-26BSF; 14-20BW 16-11 | PG361/4-11.5 | ||||||
| TM2C32-5 | 42.0 | 2-28SW | 2-11 | 2-11 | 2-11.5 | 2-11.5 | PG36 | 2-115: | ||||
| TM2C40-6B | M58x1.5; 52.0 M68x4.0; M70x6.0 | 23/4-4 25/8-6UN | 27/8-6BSW; 27/8-5BSW; 33/4-4.5BSF | 21/4-11 | 21/2-8 | 21/2-8 | ||||||
外螺纹和内螺纹刀杆系列
| 错齿双刀片TMO刀杆 | 配件 | ||||||||||
| 订货代码 | 螺纹应用范围 | 尺寸mm | 一 | ||||||||
| IC | 外螺纹 | 内螺纹 | 外螺纹&内螺纹 L L1 | D D1 | D2 | 刀片螺丝 | Torx扳手 | ||||
| 1/4" | TMOC20-2-1 | 16UN | 48/32/16UN | ||||||||
| TMOC20-2-2 | 24/18UN | 48/24/18UN | 24W | ||||||||
| TMOC20-2-3 | 28/14UN | 28/14UN | |||||||||
| TMOC20-2-4 | 20UN | 20UN | 28/14W | ||||||||
| TMOC20-2-5 | 26W | 90 25 | 20 | K2T | |||||||
| TMOC20-2-6 | 20W | 11.914.5 | SN2TM | ||||||||
| TMOC20-2-7 | 19W | ||||||||||
| TMOC20-2-8 1.0/1.5ISO | 0.5/1.0/1.5ISO | ||||||||||
| TMOC20-2-9 0.75ISO | 48UN, 0.75ISO | ||||||||||
| TMOC20-2-10 | 1.25ISO | 1.251SO | |||||||||
| TMOC20-3-1 | 1.5ISO 13UN | 0.5/1.5ISO 13UN | 16.6 20.0 | K3T | |||||||
| TMOC20-3-2 TMOC20-3-3 | 28UN | 32/28UN | 26W | 43 20 | SN3T | ||||||
| TMOC20-3-4 | 27UN | 27UN | |||||||||
| TMOC20-3-5 | 11.5UN | ||||||||||
| TMOC20-3-6 | 24/20/18/16/14/12UN 24/20/18/16/14/12UN | 11.5NPS | |||||||||
| TMOC20-3-7 | 1.25ISO | 1.25ISO | 26/20/18/16/14/12W,14NPS 95 | ||||||||
| TMOC20-3-8 | 24W | ||||||||||
| TMOC20-3-9 | 19W | ||||||||||
| TMOC20-3-10 1.0/2.0ISO | 0.5/1.0/2.0ISO | 11W | |||||||||
| TMOC20-3-110.75ISO | 32UN, 0.75ISO | ||||||||||
| TMOC20-3-12 | 1.75ISO | 1.75ISO | |||||||||
| 24 | 30.0 | ||||||||||
| 5/8" | TMOC25-5-1 | 24/20/18/14/13/12UN24/20/18/14/13/11UN | 14W | 52 25 | SN5TM | ||||||
| TMOC25-5-2 | 24/18/12UN | 24/18/12/6UN | 12W | ||||||||
| TMOC25-5-3 | 16UN | 16UN | 16W, 8NPS | ||||||||
| TMOC25-5-4 TMOC25-5-5 | 14/7UN | 14UN 11.5UN | 14/7W | ||||||||
| TMOC25-5-6 | 11UN | 11UN | 11.5NPS 11W | ||||||||
| TMOC25-5-7 | 10UN | 10/5UN | 10W | ||||||||
| TMOC25-5-8 | 9UN | 9UN | 9W | ||||||||
| TMOC25-5-9 | 8UN | 8UN | 8W | ||||||||
| TMOC25-5-10 | 7UN | ||||||||||
| 6W | |||||||||||
| TMOC25-5-116UN | TMOC25-5-12 1.0/2.0/2.5/4.0ISO | 1.0/2.0/2.5/4.0/5.0ISO | |||||||||
| TMOC25-5-131.25ISO | 1.25ISO | ||||||||||
| TMOC25-5-14 1.5/2.5/4.5ISO | 1.5/2.5/4.5/ISO | ||||||||||
| TMOC25-5-151.75ISO | 1.75ISO | ||||||||||
| TMOC25-5-16 1.0/1.5/3.0/3.5ISO | 1.0/1.5/3.0/3.5ISO | ||||||||||
外螺纹和内螺纹刀杆系列
| TM-刀盘 配件 | |||||||
| 刀片尺寸 | 订货代码 | 切削刃 刀片 | 尺寸mm | 一 | S / | ||
| IC | D2 | d(H7) | H | 刀片螺钉 | Torx扳手 | 连接螺钉 | |
| 1/4" | TMSH-D38-16-2 | 6 | 38.0 16.0 | 40.0 | M8x1.25x35 | ||
| 1/4" | TMSH-D50-22-2 | 8 | 50.0 22.0 | 40.0 | SN2T | HK2T | M10x1.50x35 |
| 3/8″ | TMSH-D50-22-3 | 6 | 50.0 22.0 | 40.0 | |||
| 3/8B" | TMSH-D63-22-3B | 6 | 63.0 22.0 | 40.0 | SN3TM | HK3T | M10x1.50x35 |
| 5/8" | TMSH-D63-22-5 | 4 | 63.0 22.0 | 45.0 | SN5TM | HK5T | M10x1.50x35 |
| 3/4B" | TMSH-D63-22-6B | 4 | 63.0 22.0 | 50.0 | SM7T | HK7T | M10x1.50x35 |
| 5/8" | TMSH-D80-27-5 | 6 | 80.0 27.0 | 50.0 | SN5TM | HK5T | M12x1.75x40 |
| 3/4B" | TMSH-D80-27-6B | 5 | 80.0 27.0 | 50.0 | SM7T | HK7T | M12x1.75x40 |
| 5/8″ | TMSH-D100-32-5 | 7 | 100.0 32.0 | 55.0 | SN5TM | HK5T | M16x2.00x40 |
| 3/4B" | TMSH-D100-32-6B | 6 | 100.0 32.0 | 55.0 | SM7T | HK7T | M16x2.00x40 |
| 5/8″ | TMSH-D125-40-5 | 9 | 125.0 40.0 | 63.0 | SN5TM | HK5T | M20x2.50x50 |
| 3/4B" | TMSH-D125-40-6B | 8 | 125.0 40.0 | 63.0 | SM7T | HK7T | M20x2.50x50 |
内螺纹盘铣刀
| 刀杆 最小螺纹直径 | ||||||||||||
| D2 (mm) | ISO细牙 | UNC | UN/UNF/UNEF/UNS | UNJ | BSW/BSF | BSP | BSPT | NPT | NPTF | PG | NPS | |
| TMSH-D38-16-2 | 38.0 | M45x1.5 | 1 | 134-26BSW | PG36 | |||||||
| TMSH-D50-22-2 | 50.0M56x1.5 | 21/4-20UN; 21/4-18UNS; 21/4-16UNS; 2/4-14UNS | 2/4-20UNJ; 21/4-16UNJ | |||||||||
| TMSH-D50-22-3 | 50.0 | M56x1.5; M58x2.0 | 21/4-20UN; 31/4-18UNS;2/4-20UNJ; 3/4-16UNS; 31/4-14UNS; 2/4-16UNJ; 23/-12UN | 23/8-12UNJ | 2/4-20BSW; 23/-16BSW; 23/-12BSW | 2/4-11 | PG42 | 2-11.5 | ||||
| TMSH-D63-22-3B | 63.0 | M70x1.5; M70x2.0 | 23/4-20UN; 23/4-18UNS; 23/4-16UNS; 23/4-14UNS; 27/%-12UN | 212-11 | ||||||||
| TMSH-D63-22-5 | 63.0 | M70x1.5; M70x2.0; M75x3.0; M80x4.0 | 33/4-16UNS; 33/4-14UNS; 23/4-20UN:3/4-18UNS；23%4-16UNJ; 276-12UN:3-10U3-U2U | 278-16BSW; 31-8BSW | 21/2-11 | 3-11 | 3-8 | |||||
| TMSH-D63-22-6B | 63.0 | M70×2.0; M80x4.0; | 3/4-43/4-6UN | 3/%-4.5SWF | 212-11 | 3-8 | 3-8 | |||||
| TMSH-D80-27-5 | 80.0 | M90x2.0; M95x3.0; M95x4.0 | 3V-14UNS:3-12UN; 33/4-10UNS; 33/4-8UN | 33/-16UNJ; 31/2-12UNJ | 3/2-16BSW; 33/4-8BSW | 31/4-11 | 4-11 | 31/2-8 | ||||
| TMSH-D80-27-6B | 80.0 | M10×2.0M95x4.0; | 37/-6UN | 4-6BSW 41/4-16BSW; | 31/4-11 | 31/-8 | 31/-8 | |||||
| TMSH-D100-32-5 | 100.0 | M110x2.0; M115x3.0; M115x4.0 | 4/4-16UNJ; 43/-12UNJ | 4/4-12BSSW; | 4-11 | 4-11 | ||||||
| TMSH-D100-32-6B | 100.0 | M110x2.0; M115x4.0; M125x6.0 | 47/-6BSW | 4-11 | 5-8 | 5-8 | ||||||
| TMSH-D125-40-5 | 125.0 | M145×2.0;M140x3.0; | 5y4-1UNJ | 5-11 | 5-11 | |||||||
| TMSH-D125-40-6B | 125.0 | M135x2.0; M140x4.0; M150x6.0 | 57/-6BSW | 5-11 | 5-8 | 5-8 | ||||||
外螺纹和内螺纹刀杆系列
| 单齿(标准刀片)TMS铣刀 | ||||||||
| 刀片尺寸 | 订货代码 | |||||||
| IC | L | L1 | D | D1 | D2 | 刀片螺钉 | Torx扳手 | |
| 1/4" | TMSC10-2 | 65 | 25 | 10 | 9.3 | 12.5 | SN2TK | K2T |
使用标准平装螺纹车刀刀片。 参阅螺纹车刀刀片章节-第17页。左手外螺纹刀片加工外螺纹，右手内螺纹刀片加工内螺纹。
外螺纹和内螺纹刀杆系列
| TMV-单齿立装刀杆 | 配件 | |||||||
| 刀片尺寸 | 订货代码 | 尺寸mm | ||||||
| IC | L | L1 | D | D1 | D2 | 刀片螺钉 | Torx扳手 | |
| 5/8"V | TMVC32-5 | 120 | 60 | 32 | 35.6 | 46 | SN6T | K6T |
需安装IC5/8”立装螺纹车刀片（宽度 \lceil = 6 \rceil ）。 使用左手外螺纹刀片加工外螺纹，右手内螺纹刀片加工内螺纹刀片。
推荐材质，切削速度Vc [m/min]和进给f[mm/齿]
| 材料 | 材料 | 布氏硬度 | Vc [m/min] | 给 | ||||
| 有涂层 | 无涂层 | |||||||
| VBX | VTX | VK2 | ||||||
| P 钢 | 1 2 3 | 低碳钢(C=0.1-0.25%) | 125 | 100-210 | 90-180 | 0.05-0.3 | ||
| 非合金钢 | 中碳钢(C=0.25-0.55%) | 150 | 100-180 | 90-170 | 0.05-0.25 | |||
| 4 | 高碳钢(C=0.55-0.85%) | 170 | 100-170 | 90-160 | 0.05-0.2 | |||
| 5 | 未淬火 | 180 | 90-160 | 90-155 | 0.05-0.25 | |||
| 6 | 低合金钢 （合金含量≤5%) | 淬火 | 275 | 80-180 | 80-160 | 0.05-0.2 | ||
| 7 | 淬火 | 350 | 70-140 | 70-150 | 0.05-0.15 | |||
| 8 9 | 高合金钢 (合金含量>5%) | 退火 | 200 | 60-130 | 70-115 | 0.05-0.2 | ||
| 淬火 | 325 | 70-110 | 60-100 | 0.05-0.1 | ||||
| 铸钢 | 低合金钢(合金含量≤5%) | 200 | 100-170 | 100-170 | 100-150 | 0.05-0.15 | ||
| M | 11 12 13 14 | 铁素体不锈钢 | 高合金钢 (合金含量>5%) | 225 | 70-120 | 70-130 | 60-130 | 0.05-0.1 |
| 未淬火 | 200 | 100-170 | 120-180 | 0.05-0.15 | ||||
| 淬火 | 330 | 100-170 | 120-180 | 0.05-0.1 | ||||
| 奥氏体不锈钢 | 奥氏体 | 180 | 70-140 | 100-140 | 0.05-0.15 | |||
| 超级奥氏体 | 200 | 70-140 | 100-140 | 0.05-0.1 | ||||
| 铁素体铸造不锈钢 | 未淬火 | 200 | 70-140 | 100-140 | 0.05-0.15 | |||
| 淬火 奥氏体 | 330 | 70-140 | 100-140 | 0.05-0.1 | ||||
| K 铸铁 | 17 18 28 | 奥氏体铸造不锈钢 | 淬火 | 200 330 | 70-120 | 100-120 100-120 | 0.05-0.15 0.05-0.1 | |
| 铁素体(短切屑) | 70-120 | 0.02-0.8 | ||||||
| 29 30 31 | 可锻铸铁 | 130 230 | 60-130 | 100-120 | ||||
| 珠光体 (长切屑) | 60-120 | 80-100 | 0.02-0.05 | |||||
| 灰铸铁 | 低拉伸强度 | 180 | 60-130 | 80-100 | 0.05-0.15 | |||
| 高拉伸强度 | 260 | 60-100 | 80-100 | 0.05-0.1 | ||||
| N | 33 34 | 球磨铸铁 | 铁素体 | 160 | 60-125 | 80-100 | 0.05-0.15 | |
| 珠光体 | 260 | 50-90 | 60-90 | 0.05-0.1 | ||||
| 锻造铝合金 | 无时效处理 | 60 | 100-250 | 200-300 | 0.1-0.4 | |||
| 时效处理 铸造 | 100 | 100-180 | 60-110 | 0.1-0.3 | ||||
| 36 铝合金 37 38 铝合金 | 75 | 150-400 | 60-120 | 0.1-0.3 | ||||
| 铸件&时效处理 | 90 | 150-280 | 60-100 | 0.05-0.25 | ||||
| 39 铜和铜合金 | 铸件硅含量13-22% | 130 | 80-150 | 20-50 | 0.1-0.3 | |||
| 黄铜 | 90 | 120-210 | 100-200 | 50-70 | 0.1-0.3 | |||
| S 耐热材料 | 19 20 | 40 | 青铜及无铅铜 | 100 | 120-210 | 100-200 | 50-70 | 0.05-0.25 0.05-0.1 |
| 退火 (铁基) | 200 | 20-45 | 20-40 | 20-30 | ||||
| 高温合金 | 时效 (铁基) | 280 | 20-30 20-50 | 20-30 15-20 | 15-25 | 0.02-0.05 0.02-0.05 | ||
| 退火 (镍基或钴基) 时效 (镍基或钴基) | 250 | 10-15 | 10-15 | 15-20 10-15 | 0.02-0.05 | |||
| 99.5纯钛 | 350 400Rm | 70-140 | 70-120 | 40-60 | 0.02--0.05 | |||
| 23 24钛合金 | α+β相钛合金 | 1050Rm | 20-50 | 20-50 | 20-40 | 0.02-0.05 | ||
| H 硬化材料 | 25 超硬钢 26 | 45-50HRc | 20-45 | 20-45 | 0.01-0.03 | |||
| 淬硬&调质 | 51-55HRc | 20-45 | 20-45 | 0.01-0.02 | ||||
材质
| 材质 | 应用 | 应用 |
| VBX | 钢件和铸铁加工首选， 高韧性亚微粒基体带TiCN涂层 | |
| VTX | 不锈钢加工首选 高韧性亚微粒基体带TiAIN涂层 | |
| VK2 | 无涂层材质适用于加工铸铁和有色金属 |
TMSD
深孔螺纹铣刀
刀片 | 刀杆
Vardex产品订货码
| 5-螺纹标准 | |
| 60-60°范牙型 | |
| 55-55°范牙型 | |
| ISO-ISO 公制螺纹 UN-美制UN |
| 6-刀具系统 |
| TM-TMSD (U,A,L类型) TM3-TMSD立装型 |
| 7-刀片材质 |
| VBX,VTX |
TMSD 刀杆 (U, A, L 型)
TMSD刀杆(立装型)
C GM C 9 C 13 45 7 31 2 3 4 5 6 7 8 91 – 刀杆型式 2 – 加工类型 3 - 冷却方式 4 – 刀杆柄径 5 - 刀杆形式 切削直径 7-刀具悬长 8 - 刀片尺寸空白 - 钢制柄 GM - 槽铣和螺纹铣 C - 内冷 8, 9, 11.5, 12, C - 圆柱柄 10.5-22.0 25-65 7 - IC6.8 mmC - 硬质合金柄 14, 15, 20, 25 W - 侧固柄 9 - IC8.5 mm
TMSD刀盘(U,L,V型)
