Pipe Supports

Pipe Supports

49 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

B3088ST - Threaded Seismic Base Stand

Size Range: 1\" (25mm) thru 4\" (100mm) pipe

Material: Steel

Function: Designed as a threaded base stand where vertical

adjustment is required for pipe supports B3089, B3092, and

B3093, to meet requirements of 12X anchor diameter hole

spacing for seismic applications. The standard B3088-3 &

B3088-6 already meet this requirement.

Finish: Plain or Electro-Galvanized. Contact customer service

for alternative finishes and materials.

Order By: Figure number, height and finish.

H

4 Holes

Plate Size

Stand Pipe Size

TL

Thread Length

A

A

**Specify

Height

**Height from

top of pipe to

bottom of plate.

Plate Size Stand Pipe Size A Dia. H TL

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3088ST-1 1

/4\" x 8\" x 8\" (6.3 x 203.2 x 203.2) 1\" (25) 1\" (25.4) 9

/16\" (14.3) 11

/2\" (38.1)

B3088ST-11

/4 1

/4\" x 8\" x 8\" (6.3 x 203.2 x 203.2) 11

/4\" (32) 1\" (25.4) 9

/16\" (14.3) 11

/2\" (38.1)

B3088ST-11

/2 1

/4\" x 8\" x 8\" (6.3 x 203.2 x 203.2) 11

/2\" (40) 1\" (25.4) 9

/16\" (14.3) 11

/2\" (38.1)

B3088ST-2 1

/4\" x 8\" x 8\" (6.3 x 203.2 x 203.2) 2\" (50) 1\" (25.4) 9

/16\" (14.3) 11

/2\" (38.1)

B3088ST-21

/2 3

/8\" x 81

/2\" x 81

/2\" (9.5 x 215.9 x 215.9) 21

/2\" (65) 11

/4\" (31.7) 9

/16\" (14.3) 11

/2\" (38.1)

B3088ST-4 1

/2\" x 131

/2\" x 131

/2\" (12.7 x 342.9 x 342.9) 4\" (100) 11

/2\" (38.1) 15/16\" (23.8) 2\" (50.8)

*Based on a height of 18\" (457.2mm).

Approx. Wt./100*

Part No. Lbs. (kg)

B3088ST-1 708 (321.1)

B3088ST-11

/4 798 (362.0)

B3088ST-11

/2 858 (389.2)

B3088ST-2 993 (450.4)

B3088ST-21

/2 1638 (743.0)

B3088ST-4 4202 (1906.0)

Note: Match B3088TS part number with dimension ‘D’ from B3092, and B3093 charts.

Pipe Supports

Pipe Supports

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

50 Eaton B-Line series Fire Protection Solutions

Size Range: 3

/4\" (20mm) thru 36\" (900mm) pipe

Material: Steel with cast iron reducer

Function: Designed to support horizontal pipe from floor

stanchion where vertical adjustment is required. U-bolt

and hex nuts are provided to hold pipe securely to saddle.

To complete floor stanchion, use with B3088T (page 42)

threaded pipe stand.

Approvals: Conforms to Federal Specification

WW-H-171E & A-A-1192A and Manufacturers Standardization

Society ANSI/MSS SP-69 & SP-58, Type 37.

Finish: Plain. Contact customer service for alternative

finishes and materials.

Order By: Figure number and finish

Notes: Order with B3088T for complete stanchion support.

4\" (100mm) thru 12\" (300mm) fits both steel and ductile iron

pipe. For other ductile iron pipe sizes specify B3092DI - size.

3\" (80mm) Ductile Iron uses B3092-31

/2

E

U-Bolt Dia.

Steel Size

Gussets on sizes

B3092-8 and larger.

A

Schedule 40 Pipe Size

B

Center of pipe to

bottom of pipe reducer.

C

Center of pipe to

bottom lip of support.

D

Nominal pipe size of base stand -

not included.

E

U-Bolt Dia.

A

D

C

B

Pipe Size Maximum O.D. of Pipe A Minimum B Maximum

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3092-3

/4 3

/4\" (19) 13

/8\" (34.9) 3

/4\" (19) 53

/4\" (146.0) 101

/4\" (260.3)

B3092-1 1\" (25) 13

/8\" (34.9) 3

/4\" (19) 529/32\" (150.0) 1013/32\" (264.3)

B3092-11

/4 11

/4\" (32) 111/16\" (42.9) 3

/4\" (19) 65

/64\" (154.4) 1037/64\" (268.7)

B3092-11

/2 11

/2\" (38) 2\" (50.8) 3

/4\" (19) 61

/4\" (158.7) 103

/4\" (273.0)

B3092-2 2\" (50) 27

/16\" (61.9) 3

/4\" (19) 67

/16\" (163.5) 1015/16\" (277.8)

B3092-21

/2 21

/2\" (65) 27

/8\" (73.0) 11

/2\" (40) 67

/8\" (174.6) 113

/8\" (288.9)

B3092-3 3\" (80) 31

/2\" (88.9) 11

/2\" (40) 73

/16\" (182.6) 1111/16\" (296.9)

B3092-31

/2 31

/2\" (90) 4\" (101.6) 11

/2\" (40) 77

/16\" (188.9) 1115/16\" (303.2)

B3092-4 4\" (100) 47

/8\" (123.8) 21

/2\" (65) 713/16\" (198.4) 125

/16\" (312.7)

B3092-5 5\" (125) 55

/8\" (142.9) 21

/2\" (65) 89

/32\" (210.3) 1225/32\" (324.6)

B3092-6 6\" (150) 629/32\" (175.4) 21

/2\" (65) 91

/16\" (230.2) 139

/16\" (344.5)

B3092-8 8\" (200) 91

/8\" (231.8) 21

/2\" (65) 101

/2\" (266.7) 15\" (381.0)

B3092 - Adjustable Pipe Saddle Support with Yoke

C D (Not Supplied) E Saddle Steel Size Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3092-3

/4 2\" (50.8) 11

/2\" (38) 1

/4\" (6.4) 1

/4\" x 11

/2\" (6.3 x 38.1) 247 (112.0)

B3092-1 25

/32\" (54.8) 11

/2\" (38) 1

/4\" (6.4) 1

/4\" x 11

/2\" (6.3 x 38.1) 257 (116.6)

B3092-11

/4 221/64\" (59.1) 11

/2\" (38) 3

/8\" (9.5) 1

/4\" x 2\" (6.3 x 50.8) 289 (131.1)

B3092-11

/2 21

/2\" (63.5) 11

/2\" (38) 3

/8\" (9.5) 1

/4\" x 2\" (6.3 x 50.8) 306 (138.8)

B3092-2 211/16\" (68.3) 11

/2\" (38) 3

/8\" (9.5) 1

/4\" x 2\" (6.3 x 50.8) 326 (147.9)

B3092-21

/2 31

/8\" (79.4) 21

/2\" (65) 1

/2\" (12.7) 1

/4\" x 3\" (6.3 x 76.2) 651 (295.3)

B3092-3 37

/16\" (87.3) 21

/2\" (65) 1

/2\" (12.7) 1

/4\" x 3\" (6.3 x 76.2) 716 (324.8)

B3092-31

/2 311/16\" (93.7) 21

/2\" (65) 1

/2\" (12.7) 1

/4\" x 3\" (6.3 x 76.2) 717 (325.2)

B3092-4 41

/4\" (107.9) 3\" (80) 1

/2\" (12.7) 3

/8\" x 31

/2\" (9.5 x 88.9) 1286 (583.3)

B3092-5 49

/16\" (115.9) 3\" (80) 1

/2\" (12.7) 3

/8\" x 31

/2\" (9.5 x 88.9) 1321 (599.2)

B3092-6 51

/2\" (139.7) 3\" (80) 5

/8\" (15.9) 1

/2\" x 31

/2\" (12.7 x 88.9) 1595 (723.5)

B3092-8 7\" (177.8) 3\" (80) 5

/8\" (15.9) 1

/2\" x 31

/2\" (12.7 x 88.9) 1815 (823.3)

Pipe Supports

Pipe Supports

51 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: 1\" (25mm) thru 36\" (900mm) pipe

Material: Steel with cast iron reducer

Function: Designed to support horizontal pipe from

floor stanchion where vertical adjustment is required.

U-bolt and hex nuts are provided to hold pipe securely

to saddle. To complete floor stanchion, use with

B3088T (page 42) threaded pipe stand.

Approvals: Conforms to Federal Specification

WW-H-171E & A-A-1192A, Type 38 and

Manufacturers Standardization Society ANSI/MSS

SP-69 & SP-58, Type 37.

Finish: Plain. Contact customer service for alternative

finishes and materials.

Order By: Figure number and finish

Note: Order with B3088T for complete stanchion

support.

B3093 - Adjustable Pipe Saddle Support

Steel Size

Gussets on sizes

B3093-8 and larger.

A

D

C

B

Pipe Size Maximum O.D. of Pipe A Minimum B Maximum C

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3093-1 1\" (25) 15

/16\" (33.3) 3

/4\" (20) 521/32\" (143.6) 105

/32\" (257.9) 129/32\" (48.4)

B3093-11

/4 11

/4\" (32) 111/16\" (42.9) 3

/4\" (20) 553/64\" (148.0) 1021/64\" (2262.3) 25

/64\" (52.8)

B3093-11

/2 11

/2\" (40) 129/32\" (48.4) 3

/4\" (20) 6\" (152.4) 101

/2\" (266.7) 21

/4\" (58.1)

B3093-2 2\" (50) 23

/8\" (60.3) 3

/4\" (20) 63

/16\" (157.2) 1011/16\" (271.5) 27

/16\" (61.9)

B3093-21

/2 21

/2\" (65) 27

/8\" (73.0) 11

/2\" (40) 65

/16\" (160.3) 1013/16\" (274.6) 29

/16\" (65.1)

B3093-3 3\" (80) 31

/2\" (88.9) 11

/2\" (40) 65

/8\" (168.3) 111

/8\" (282.6) 27

/8\" (73.0)

B3093-31

/2 31

/2\" (90) 4\" (101.6) 11

/2\" (40) 67

/8\" (174.6) 113

/8\" (288.9) 31

/8\" (79.4)

B3093-4 4\" (100) 47

/8\" (123.8) 21

/2\" (65) 71

/4\" (184.1) 113

/4\" (298.4) 31

/2\" (88.9)

B3093-5 5\" (125) 59

/16\" (141.3) 21

/2\" (65) 725/32\" (197.6) 129

/32\" (311.9) 41

/32\" (102.4)

B3093-6 6\" (150) 7\" (177.8) 21

/2\" (65) 87

/16\" (214.3) 1215/16\" (328.6) 411/16\" (119.1)

B3093-8 8\" (200) 91

/8\" (231.8) 21

/2\" (65) 101

/4\" (260.3) 143

/4\" (374.6) 61

/2\" (165.1)

Note:

4\" (100) thru 12\" (300) fits both steel and ductile iron pipe.

For other ductile iron pipe sizes specify B3093DI - size.

3\" (80) Ductile Iron uses B3093-31

/2

D (Base Stand Approx. Wt./100

Not Supplied) Saddle Steel Size Complete Saddle Only

Part No. in. (mm) in. (mm) Lbs. (kg) Lbs. (kg)

B3093-1 11

/2\" (40) 1

/4\" x 13

/4\" (6.3 x 44.4) 189 (85.7) 49 (22.2)

B3093-11

/4 11

/2\" (40) 1

/4\" x 13

/4\" (6.3 x 44.4) 221 (100.2) 81 (36.7)

B3093-11

/2 11

/2\" (40) 1

/4\" x 13

/4\" (6.3 x 44.4) 228 (103.4) 88 (39.9)

B3093-2 11

/2\" (40) 1

/4\" x 13

/4\" (6.3 x 44.4) 234 (106.1) 94 (42.6)

B3093-21

/2 21

/2\" (65) 1

/4\" x 3\" (6.3 x 76.2) 567 (257.2) 167 (75.8)

B3093-3 21

/2\" (65) 1

/4\" x 3\" (6.3 x 76.2) 576 (261.3) 176 (79.9)

B3093-31

/2 21

/2\" (65) 1

/4\" x 3\" (6.3 x 76.2) 588 (266.7) 188 (85.3)

B3093-4 3\" (80) 1

/4\" x 4\" (6.3 x 101.6) 1064 (482.6) 364 (165.1)

B3093-5 3\" (80) 1

/4\" x 4\" (6.3 x 101.6) 1081 (490.3) 381 (172.8)

B3093-6 3\" (80) 3

/8\" x 4\" (9.5 x 101.6) 1234 (559.7) 534 (242.2)

B3093-8 3\" (80) 3

/8\" x 4\" (9.5 x 101.6) 1496 (678.6) 796 (361.1)

A

Schedule 40 Pipe Size

B

Center of pipe to bottom of pipe

reducer.

C

Center of pipe to bottom lip of

support.

D

Nominal pipe size of base stand

- not included.

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

52 Eaton B-Line series Fire Protection Solutions

Size Range: One size accommodates all Fig. 900 Series sway brace

attachments. Fits from 3

/8\" (9.4mm) to 7

/8\" (22.2mm) thick steel structure.

For thicknesses less than 3

/8\" (9.4mm) refer to Fig. 825 and Fig. 825A.

Material: Steel

Function: To attach sway bracing and/ot hangers to various types of steel

structural members.

Features: Permits secure non-friction connection without drilling or welding.

Unique design allows offset placement on wide flange beam, C-channel, open

web, welded steel trusses, etc. Secures brace to structure either across or

along the beam. Break-off set bolts allow for visual verification of proper

installation torque.

Approvals: Underwriters Laboratories Listed in the USA and Canada (cULus).

Included in our Seismic Engineering Guidelines approved by the State of California

Office of Statewide Health Planning and Development (OSHPD). For additional

load, spacing and placement information relating to OSHPD projects, please refer

to our Seismic Engineering Guidelines, OPM-0052-13.

For FM Approval information refer to FM Approved page 53.

Installation Instructions: The Fig. 828 is the structural attachment component

of a longitudinal or lateral sway brace assembly. It is intended to be combined

with a TOLCO transitional attachment, “bracing pipe\" and a TOLCO “braced pipe”

attachment to form a complete bracing assembly. NFPA 13 guidelines should

be followed.

To Install: Slide the Fig. 828 on the flange of the beam, truss, or girder. Be

sure the attachment is fully engaged to the rear of the opening. Tighten the

cone point set screws until the heads break off. Remove the flange nut from

the carriage bolt. Install a TOLCO swivel fitting (Fig, 909, 910, 980, *986).

Use flange nut to secure the swivel fitting.

*Not UL listed when used in combination with Fig. 986

Finish: Plain or Electro-Galvanized

Approx. Weight/100: 341 Lbs. (154.7 kg)

Order By: Figure number and finish

Patent Pending

Note: Retaining strap not required.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 828 - universal sway brace attachment to steel (UL listed)

OPM

Beam, truss

or girder

May pivot

in any

direction

Fig. 828

Fig. 828

Flange

thickness

Maximum

UL Rated load

.375\" – .499\" 1090 lbs. (4.84kN)

.500\" – .875\" 1370 lbs. (6.09kN)

Set Screws

and 1

/2\" Attachment

Bolt and Nut

Included

Updated 4-6-21

Seismic Bracing

Seismic Bracing

53 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: One size accommodates all Fig. 900 Series sway brace attachments. Fits

from 3

/8\" (9.4mm) to 7

/8\" (22.2mm) thick steel structure. For thicknesses less than 3

/8\" (9.4mm)

refer to Fig. 825.

Material: Steel

Function: To attach sway bracing and/or hangers to various types of steel structural

members.

Features: Permits secure non-friction connection without drilling or welding. Unique

design allows offset placement on wide flange beam, C-channel, open web,

welded steel trusses, etc. Secures brace to structure either across or along the beam.

Break-off set bolts allow for visual verification of proper installation torque.

Approvals: Factory Mutual Approved (FM). Included in our Seismic Engineering

Guidelines approved by the State of California Office of Statewide Health Planning and

Development (OSHPD). For additional load, spacing and placement information relating to

OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13.

For UL Listed information refer to UL Listed page 52.

Installation Instructions: The Fig. 828 is the structural attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with a TOLCO™

transitional attachment, “bracing pipe” and a TOLCO “braced pipe” attachment to form a

complete bracing assembly. NFPA 13 or FM guidelines should be followed.

To Install: Slide the Fig. 828 on the flange of the beam, truss, or girder. Be sure the

attachment is fully engaged to the rear of the opening. Tighten the cone point set screws

until the heads break off. Remove the flange nut from the carriage bolt. Install a TOLCO

swivel fitting (Fig, 909, 910, 980, *986). Use flange nut to secure the swivel fitting.

*Not UL listed when used in combination with Fig. 986

Finish: Plain or Electro-Galvanized

Approx. Weight/100: 341 Lbs. (154.7kg)

Order By: Figure number and finish

Patent Pending

Designed to meet or exceed requirements of FM DS 2-8.

Note: Retaining strap not required.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 828 - Universal sway brace attachment to steel (FM approved)

OPM

Beam, truss

or girder

May pivot

in any

direction

Fig. 828

Fig. 828

Set Screws

and 1

/2\" Attachment

Bolt and Nut

Included

Updated 4-6-21

FM Approved Allowable Horizontal Load

With Brace Perpendicular To Beam

Brace Angle (degrees from vertical)

30°-44° 45°-59° 60°-74° 75°-90°

980 2220 3340 4040

(4.350kN) (9.780kN) (14.850kN) (17.970kN)

FM Approved Allowable Horizontal Load

With Brace Parallel To Beam

Brace Angle (degrees from vertical)

30°-44° 45°-59° 60°-74° 75°-90°

820 1270 1490 1650

(3.640kN) (5.640kN) (6.620kN) (7.330kN)

FM Approved design loads are based on ASD

design method.

Size Range: One size accommodates all

Fig. 900 Series sway brace attachments.

Material: Steel

Function: To attach sway bracing and hanger assemblies

to steel members.

Features: This product’s design incorporates a concentric

attachment point which is critical to the performance of

structural seismic connections. NFPA 13 indicates the

importance of concentric loading of connections and

fasteners. Permits secure non-friction connection without

drilling or welding. Unique design reinforces point of

connection to joist. Break off head set bolt design assures verification of proper

installation torque (min. 31 ft.-lbs.).

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).

UL listed with Fig. 909, 910, and 980 series attachments and the following brace

member type pipes: Sch. 40, KSD 3562. Included in our Seismic Engineering

Guidelines approved by the State of California Office of Statewide Health Planning

and Development (OSHPD). For additional load, spacing and placement information

relating to OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13. For FM Approval information refer to FM Approved page 55.

Installation Instructions: Fig. 825 is the structural attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with

a TOLCO™ transitional attachment, “bracing pipe” and a TOLCO “braced pipe”

attachment, to form a complete bracing assembly. NFPA 13 guidelines should be

followed.

To Install: Place the Fig. 825 on the steel beam, tighten the cone point set bolts

until heads break off. Attach other TOLCO transitional attachment fitting, Fig. 980,

910, 909, or any other TOLCO approved

transitional fitting. Transitional fitting

attachment can pivot for adjustment to

proper brace angle.

Finish: Plain, Electro-Galvanized and HDG

Approx. Wt./100: 247.5 Lbs. (112.2kg)

Order By: Figure number and finish

US Patent #6,098,942

Canada Patent #2,286,659

Retaining strap not required.

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

54 Eaton B-Line series Fire Protection Solutions

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 825 - bar joist sway brace attachment to steel (UL listed)

Front View

May pivot in any

direction

Shown with

Fig. 910

Bar joist shown attached to

various roof materials

Top View

1\" (25.4mm)

1

/2\" Bolt & Nut

Furnished

Fig. 825

Fig. 980

Brace

I-Beam

3

/8\"

(9.5)

Set Bolts & Hardware

Included

OPM

Fig. 4L

Fig. 825

Fig. 825

Fig. 1001 Fig. 1001

Fig. 980

Fig. 980

Maximum Design Load

825W/909-1370 lbs (5.78 KN)

825W/910-1500 lbs (7.11 KN)

825W/980-1600 lbs (8.45 KN)

UL Listed as Hanger Attachment for

6\" (150mm) pipe at Maximum Spacing

Updated 5-24-21

Seismic Bracing

Seismic Bracing

55 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: One size accommodates all

Fig. 900 Series sway brace attachments.

Material: Steel

Function: To attach sway bracing and hanger assemblies

to steel members.

Features: This product’s design incorporates a concentric

attachment point which is critical to the performance

of structural seismic connections. NFPA 13 indicates

the importance of concentric loading of connections

and fasteners. Permits secure non-friction connection

without drilling or welding. Unique design reinforces point

of connection to joist. Break off head set bolt design assures verification of proper

installation torque (min. 31 ft.-lbs.).

Approvals: Approved by Factory Mutual Engineering (FM).

Included in our Seismic Engineering Guidelines approved by the State of California

Office of Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to our

Seismic Engineering Guidelines, OPM-0052-13

For UL Listed information refer to UL Listed page 54.

Installation Instructions: Fig. 825 is the structural attachment componentof a

longitudinal or lateral sway brace assembly. It is intended to be combined with

a TOLCO™ transitional attachment, “bracing pipe” and a TOLCO “braced pipe”

attachment, to form a complete bracing assembly. NFPA 13 or FM guidelines should

be followed.

To Install: Place the Fig. 825 on the steel beam, tighten the cone point set bolts until

heads break off. Attach other TOLCO transitional attachment fitting, Fig. 980, 910, 909,

or any other TOLCO approved transitional fitting. Transitional fitting attachment can

pivot for adjustment to proper brace angle.

Finish: Plain, Electro-Galvanized and HDG

Approx. Wt./100: 247.5 Lbs. (112.2kg)

Order By: Figure number and finish

US Patent #6,098,942,

Canada Patent #2,286,659

Designed to meet or exceed

requirements of FM DS 2-8.

Retaining strap not required.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 825 - bar joist sway brace attachment to steel (FM approved)

Fig. 4L

Top View

1\"

(25.4mm) 1

/2\" Bolt & Nut

Furnished

Fig. 825

Fig. 825

Fig. 825

Fig. 1000

Fig. 1001

Side View

Fig. 980

Fig. 980

Fig. 980

3

/8\"

(9.5)

FM Approved design loads are based

on ASD design method.

Set Bolts & Hardware

Included

Fig. 825

Fig. 980

Brace

I-Beam

FM Approved Design Loads

30°-44° 45°-59° 60°-74° 75°-90°

lbs. / (kN) lbs. / (kN) lbs. / (kN) lbs. / (kN)

Maximum Perpendicular to 990 1360 1670 1860 3

/8\" Thick Flange Structural Member (4.40) (6.05) (7.43) (8.27)

Maximum Parallel to 460 630 770 860 3

/8\" Thick Flange Structural Member (2.04) (2.80) (3.42) (3.82)

OPM

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

56 Eaton B-Line series Fire Protection Solutions

Size Range: One size accommodates all Fig. 900 Series sway brace attachments.

Material: Steel

Function: To attach sway bracing and/or hanger to steel structural members.

Features: This product’s design incorporates a concentric attachment point which

is critical to the performance of structural seismic connections. NFPA 13 indicates

the importance of concentric loading of connections and fasteners. Permits secure

non-friction connection without drilling or welding. Unique design reinforces point

of connection to joist. Break off head bolt design assures verification of proper

installation.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).

UL listed with Fig. 909, 910, and 980 series attachments and the following brace

member type pipes: Sch. 40, KSD 3562. Included in our Seismic Engineering

Guidelines approved by the State of California Office of Statewide Health Planning

and Development (OSHPD). For additional load, spacing and placement information

relating to OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13.

Installation Instructions: Fig. 825A is the structural attachment component of

a longitudinal or lateral sway brace assembly. It is intended to be combined with

a TOLCO™ transitional attachment, “bracing pipe” and a TOLCO “braced pipe”

attachment to form a complete bracing assembly. NFPA 13 guidelines should

be followed.

To Install: Place the Fig. 825A on the steel beam, tighten the cone point set

bolts until heads break off. Attach other TOLCO transitional attachment fitting,

Fig. 980, 910, 909, or any other TOLCO approved transitional fitting. Transitional

fitting attachment can pivot for adjustment to proper brace angle.

Finish: Plain or Electro-Galvanized

Approx. Wt./100: 154.5 Lbs. (70.1kg)

Order By: Figure number and finish

Patent #6,098,942

Retaining strap not required.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Shown with

Fig. 910

Shown with

Fig. 1001

May pivot in any

direction

Bar joist shown attached to

various roof materials

TOLCO Fig. 825A - bar joist sway brace attachment to steel

Maximum Design Load

825A 700 lbs. (3.11kN)

UL Listed as Hanger

Attachment for 8\" (200mm)

Pipe at Maximum Spacing

3

/8\"

(9.5)

Set Bolts & Hardware

Included

OPM

Updated 5-24-21

Seismic Bracing

Seismic Bracing

57 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Material: Steel

Application: Allows sway brace fittings to develop greater

load carrying ability by providing multiple fastener attachments

for steel and wood. The National Fire Protection (NFPA)

provides information on fastener loads to various structures.

Refer to NFPA 13 (2016) 9.3.5.9.1.

Approvals: Underwriters Laboratories Listed in the USA

(UL) and Canada (cUL) only when used with TOLCO™ Fig. 900

Series Earthquake Brace Attachments. Included in our Seismic

Engineering Guidelines approved by the State of California

Office of Statewide Health Planning and Development

(OSHPD). For additional load, spacing and placement

information relating to OSHPD projects, please refer to our

Seismic Engineering Guidelines, OPM-0052-13.

Installation Instructions: Fig. 906 is a multiple fastener

structural attachment component of a longitudinal or lateral

sway brace assembly. It is intended to be combined with a

TOLCO transitional attachment, “bracing pipe” and a TOLCO

“braced pipe” attachment to form a complete bracing

assembly. NFPA 13 guidelines should be followed.

To Install: Attach the Fig. 906 to the structural surface as

per fastener design guidelines. Attach other TOLCO

transitional attachment fitting, Fig. 980, 910, 909, or any

other TOLCO approved transitional fitting. Transitional fitting

attachment can pivot for adjustment to proper brace angle.

Finish: Plain or Electro-Galvanized. Contact customer

service for alternative finishes and materials.

Order By: Figure number and specify dimensions H1 and H2.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 906 - sway brace multi-fastener adapter

Part A B C D H1 H2 Approx. Wt./100

Number in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

906 12\" (305.0) 9\" (228.6) 2.5\" (63.5) 1

/4\" (6.3) Specify Specify 394 (178.7)

906-12 15\" (381.0) 12\" (304.8) 2.5\" (63.5) 1

/4\" (6.3) Specify Specify 494 (224.1)

Load Note: Actual design load determined by anchor and concrete strength, not to exceed the UL Listed maximum

load of 1200 lbs (5.33kN).

Load is for Fig. 906. If combined load of anchors is less, must reduce to anchor maximum capacity.

C

C

A

D

B

H1

H1

H2

Mounting Hardware

Is Not Included

OPM

Seismic Bracing

Size Range: 4\" (101.6mm) thru 18\" (457.2mm) beam width

Material: Steel

Function: Seismic brace attachment to steel.

Features: This product’s design incorporates a concentric attachment point which

is critical to the performance of structural seismic connections. NFPA 13 indicates

the importance of concentric loading of connections and fasteners. Permits secure

connection to steel where drilling and/or welding of brace connection could present

structural issues.

Installation Instructions: Fig. 800 is the structural attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with

a TOLCO™ transitional attachment, “bracing pipe” and a TOLCO “braced pipe”

attachment to form a complete bracing assembly.

NFPA 13 guidelines should be followed.

To Install: Place the Fig. 800 on the steel beam, tighten the cone point set bolts

on flange until the heads break off. Tighten hex head bolts into clamp body until

lock washers are fully flat. Attach other TOLCO transitional attachment fitting, Fig.

980, 910, 909, or any other TOLCO approved transitional fitting. Transitional fitting

attachment can pivot for adjustment to proper brace angle.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).

UL listed with Fig. 909, 910, 980, 909 series attachments and the following brace

member type pipes: Sch. 40, KSD 3562. Included in our Seismic Engineering

Guidelines approved by the State of California Office of Statewide Health Planning

and Development (OSHPD). For additional load, spacing and placement information

relating to OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13.

For FM Approval information refer to FM Approved page 59.

Finish: Plain, Electro-Galvanized and Hot Dip Galvanized. Contact customer service

for alternative finishes and materials.

Order By: Figure number, type number and size number.

Example: FIG. 800 TYPE2X14-16

TOLCO Fig. 800 - adjustable sway brace attachment to steel (UL listed)

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Shown with Fig. 980

brace fitting to

pipe brace

(Lateral - Perpendicular

to Braced Pipe)

Shown with Fig. 980 brace

fitting to pipe brace

(Longitudinal - Parrallel

to Braced Pipe)

Set Bolts & Hardware

Included

Fits Beam Flange

Type Thickness

in. (mm)

800 TYPE1 Up to 3

/4\" (Up to 19.0)

800 TYPE2 3

/4\" to 11

/4\" (19.0 to 31.7)

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

58 Eaton B-Line series Fire Protection Solutions

OPM

Fits Flange Width Range Max.Design Loads (cULus)

Along or Across Beam

Part # in. (mm) Fig. 909

lbs. (kN)

Fig. 910

lbs. (kN)

Fig. 980

lbs. (kN)

800-1 4\"-6\" (101.6-152.4)

1270~ (5.65) 1400~ (6.23) 1400~ (6.23)

800-2 6\"-8\" (152.4-203.2)

800-3 8\"-10\" (203.2-254.0)

800-4 10\"-12\" (254.0-304.8)

800-5 12\"-14\" (304.8-355.6) 1270~ (5.65) 1300~ (5.78) 1300~ (5.78)

800-6 14\"-16\" (355.6-406.4)

900~ (4.00) 900~ (4.00) 900~ (4.00) 800-7 16\"-18\" (406.4-457.2)

Seismic Bracing

Size Range: 4\" (101.6mm) thru 18\" (457.2mm) beam width

Material: Steel

Function: Seismic brace attachment to steel.

Features: This product’s design incorporates a concentric attachment point which

is critical to the performance of structural seismic connections. NFPA 13 indicates

the importance of concentric loading of connections and fasteners. Permits secure

connection to steel where drilling and/or welding of brace connection could present

structural issues.

Installation Instructions: Fig. 800 is the structural attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with

a TOLCO™ transitional attachment, “bracing pipe” and a TOLCO “braced pipe”

attachment to form a complete bracing assembly.

NFPA 13 guidelines should be followed.

To Install: Place the Fig. 800 on the steel beam, tighten the cone point set bolts

on flange until the heads break off. Tighten hex head bolts into clamp body until

lock washers are fully flat. Attach other TOLCO transitional attachment fitting,

Fig. 980, 910, 909, or any other TOLCO approved transitional fitting. Transitional

fitting attachment can pivot for adjustment to proper brace angle.

Approvals: Approved by Factory Mutual Engineering (FM).

Included in our Seismic Engineering Guidelines approved by the State of California

Office of Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to our

Seismic Engineering Guidelines, OPM-0052-13.

For UL Listed information refer to UL Listed page 58.

Finish: Plain, Hot Dip Galvanized or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number, type number and size number.

Example: FIG. 800 TYPE2X14-16

Designed to meet or exceed requirements of FM DS 2-8.

TOLCO Fig. 800 - adjustable sway brace attachment to steel (FM approved)

Fits Beam Max.Design Loads (FM)*

Type Flange Thickness Laterial - Parallel to Structural Member Longitudinal - Perpendicular to Structural Member

30°-44° 45°-59° 60°-74° 75°-90° 30°-44° 45°-59° 60°-74° 75°-90°

in. (mm) lbs./(kN) lbs./(kN) lbs./(kN) lbs./(kN) lbs./(kN) lbs./(kN) lbs./(kN) lbs./(kN)

800 TYPE1 Up to 3

/4\" (Up to 19.0) 1430 1970 1980 NR 930 1310 1610 1800

(6.36) (8.76) (8.81) (NR) (4.13) (5.82) (7.16) (8.00)

800 TYPE2 3

/4\" to 11

/4\" (19.0 to 31.7) NR NR NR NR NR NR NR NR

(NR) (NR) (NR) (NR) (NR) (NR) (NR) (NR)

* The loads listed are axial loads on the brace. The horizontal

load capacity, H, of the brace is: H = F x sin ?, where ? is

the installation angle measured from the vertical.

FM Approved design loads are based on ASD design method.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Shown with Fig. 980

brace fitting to pipe brace

(Lateral - Perpendicular to

Braced Pipe)

Shown with Fig. 980

brace fitting to pipe brace

(Longitudinal - Parrallel to

Braced Pipe)

Set Bolts & Hardware

Included

Seismic Bracing

59 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Fits

Flange Width Range

in. (mm)

4-6 4\"-6\" (101.6-152.4)

6-8 6\"-8\" (152.4-203.2)

8-10 8\"-10\" (203.2-254.0)

10-12 10\"-12\" (254.0-304.8)

12-14 12\"-14\" (304.8-355.6)

14-16 14\"-16\" (355.6-406.4)

16-18 16\"-18\" (406.4-457.2)

OPM

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

60 Eaton B-Line series Fire Protection Solutions

Size Range: One size fits bracing pipe 1\" (25mm) thru 2\" (50mm), B-Line series

12 gauge (2.6mm) channel.

Material: Carbon steel

Function: Multi-functional attachment to structure or braced pipe fitting.

Features: This product’s design incorporates a concentric attachment opening which

is critical to the performance of structural seismic connections and in accordance with

NFPA 13, 2019 Section 18.5.11.5. The Fig. 980 mounts to any surface angle and the

break off bolt head assures verification of proper installation.

Installation: Fig.980 is the structural or transitional attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with the

“bracing pipe” and TOLCO™ “braced pipe” attachment, Fig. 1001, 2002, 3000, 4L or

approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines

should be followed.

To Install: Place the Fig. 980 onto the “bracing pipe”. Tighten the set bolt until the

head breaks off. Attachment can pivot for adjustment to proper brace angle.

Approvals: —Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).

UL Listed for the following brace member type pipes: Sch. 40, KSD 3562. Ask the

factory for additional information as it may vary by product size. Included in our Seismic

Engineering Guidelines approved by the State of California Office of Statewide Health

Planning and Development (OSHPD). For additional load, spacing and placement

information relating to OSHPD projects, please refer to our Seismic Engineering

Guidelines, OPM-0052-13. For FM Approval information refer to FM Approved page 61.

Note: Fig. 980 Swivel Attachment and Fig. 1001, 2002, 3000, 4L, or approved

attachment to pipe make up a sway brace system of UL Listed attachments and bracing

materials which satisfies the requirements of Underwriters Laboratories and the National

Fire Protection Association (NFPA)

Finish: Plain, Electro-Galvanized or Stainless Steel.

Contact customer service for alternative finishes.

Order By: Figure number and finish.

Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174,

Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730,

Pat. #7,669,806

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Longitudinal Brace

Fig. 980 - TOLCO Universal swivel sway brace attachment -3

/8\"-16 to 3

/4\"-10 rods

Fig. 980H - TOLCO Universal swivel sway brace attachment -7

/8\"-9 to 11

/4 \"-7

Mounting Hardware

Is Not Included

Set Bolt

Included

Fig. 4B

shown

Fig. 980

Fig. 980

OPM

Lateral Brace

Brace

Fig. 1001

Fig. 980

A

D

B B

D

A

980

A B D** Max. Design

Load (cULus)

lbs./(kN)

Approx.Wt./100

Catalog # in. (mm) in. (mm) in. (mm) lbs. (kg)

*980-3

/8

49

/16 (114.9) 21

/16 (52.4)

7

/16 (11.1) 1600 (7.12) 149 (67.6)

*980-1

/2 9

/16 (14.3) 2100 (9.34) 148 (67.1)

*980-5

/8 11/16 (17.5) 2100 (9.34) 147 (66.7)

*980-3

/4 13/16 (20.6) 2100 (9.34) 146 (66.2)

980H-7

/8

63

/4 (171.4) 31

/2 (88.9)

15/16 (23.8) Fig. 980H

is not

UL Listed

or FM

Approved

402 (182.3)

980H-1 11

/16 (27.0) 400 (181.4)

980H-11

/8 13

/16 (30.2) 397 (180.1)

980H-11

/4 15

/16 (33.3) 390 (176.9)

* Sizes available in stainless steel (980S-3

/8, 980S-1

/2, 980S-5

/8, and 980S-3

/4) and have the same

UL rating as what is listed.

** Mounting attachment hole size.

Seismic Bracing

Seismic Bracing

61 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: One size fits bracing pipe 1\" (25mm) thru 2\" (50mm), B-Line series

12 gauge (2.6mm) channel.

Material: Carbon steel

Function: Multi-functional attachment to structure or braced pipe fitting.

Features: This product’s design incorporates a concentric attachment opening

which is critical to the performance of structural seismic connections and in

accordance with NFPA 13, 2019 Section 18.5.11.5. The Fig. 980 mounts to

any surface angle and the break off bolt head assures verification of proper

installation.

Installation: Fig.980 is the structural or transitional attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with

the “bracing pipe” and TOLCO™ “braced pipe” attachment, Fig. 1000, 1001,

3000, 4L, or other TOLCO approved attachment to pipe to form a complete

bracing assembly. NFPA 13 guidelines should be followed.

To Install: Place the Fig. 980 onto the “bracing pipe”. Tighten the set bolt until

the head breaks off. Attachment can pivot for adjustment to proper brace angle.

Approvals: —Approved by Factory Mutual Engineering (FM). Included in our

Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to

our Seismic Engineering Guidelines, OPM-0052-13.

For UL Listed information refer to UL Listed page 60.

Note: Fig. 980 Swivel Attachment and Fig. 1000, 1001, 4L or other TOLCO

approved attachment to pipe that make up a sway brace system of bracing

materials which satisfies the requirements of Factory Mutual Engineering and

the National Fire Protection Association (NFPA)

Finish: Plain, Electro-Galvanized or Stainless Steel.

Contact customer service for alternative finishes.

Order By: Figure number and finish.

Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174,

Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730,

Pat. #7,669,806

Designed to meet or exceed requirements of FM DS 2-8.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Lateral Brace

Longitudinal

Brace

Fig. 4L

Fig. 1001

Fig. 980

Fig. 980

Brace

OPM

Mounting Hardware

Is Not Included

Set Bolt

Included

A

D

B B

D

A

980

Fig. 980 - TOLCO Universal swivel sway brace attachment -3

/8\"-16 to 3

/4\"-10 rods

Fig. 980H - TOLCO Universal swivel sway brace attachment -7

/8\"-9 to 11

/4 \"-7

A B D** Max. Design Load*** (FM) Approx.Wt./100

Catalog # in. (mm) in. (mm) in. (mm) 30°-44°

lbs./(kN)

45°-59°

lbs./(kN)

60°-74°

lbs./(kN)

75°-90°

lbs./(kN) lbs. (kg)

980-3

/8

49

/16 (114.9) 21

/16 (52.4)

7

/16 (11.1)

2370

(10.54)

2790

(12.41)

3360

(14.94)

3750

(16.68)

149 (67.6)

980-1

/2 9

/16 (14.3) 148 (67.1)

980-5

/8 11/16 (17.5) 147 (66.7)

980-3

/4 13/16 (20.6) 146 (66.2)

980H-7

/8

63

/4 (171.4) 31

/2 (88.9)

15/16 (23.8) 402 (182.3)

980H-1 11

/16 (27.0) 400 (181.4)

980H-11

/8 13

/16 (30.2) 397 (180.1)

980H-11

/4 15

/16 (33.3) 390 (176.9)

** Mounting attachment hole size.

*** Installed with 1\" or 11

/4 \"schedule 40 brace pipe.

Fig. 980H is not UL Listed

or FM Approved

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

62 Eaton B-Line series Fire Protection Solutions

Size Range: 1\" (25mm) bracing pipe. For brace pipe sizes larger than

1\" (25mm), use Fig. 980. Available with holes for 3

⁄8\", 1

⁄2\" or 5

⁄8\" attachment.

Material: Steel, hardened cone point set bolt

Function: The structural component of a sway and seismic bracing system.

Features: This product’s design incorporates a concentric attachment opening

which is critical to the performance of structural seismic connections. NFPA 13

indicates clearly that fastener table load values are based only on concentric

loading. No threading of the bracing pipe is required. Open design allows for

easy inspection of pipe engagement.

ApJ54plication Note: Fig. 909 is used in conjunction with the Fig. 1001 or

Fig. 4L or other approved TOLCO attachment to pipe, and joined together

with bracing pipe. Sway brace assemblies are intended to be installed in

accordance with NFPA 13. The required type, number and size of fasteners

used for the structure attachment fitting shall be in accordance with NFPA 13.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada

(cUL). UL Listed for the following brace member type pipes: Sch. 40, KSD

3562. Included in our Seismic Engineering Guidelines approved by the State of

California Office of Statewide Health Planning and Development (OSHPD). For

additional load, spacing and placement information relating to OSHPD

projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13.

Installation Instructions: Place Fig. 909 onto the bracing pipe. Tighten the

set screw until the head bottoms out on surface. When using in combination

with a Fig. 825A, Fig. 825, Fig. 828, or Fig. 906, refer to those instruction

sheets, otherwise select an anchor that is sized appropriately for the intended

use and follow anchor manufacturer’s instructions regarding structural thickness

and embedment requirements. The required type, number and size of fasteners

used for the structure attachment fitting shall be in accordance with NFPA 13.

Once the anchor is installed per the manufacturer’s direction, secure the

Fig. 909 to the anchor. Attachment can pivot for adjustment to proper

brace angle.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, fastener attachment size and finish.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 909 - no-thread swivel sway brace attachment (UL listed)

Part Mounting Hole Brace Max. Design Approx.

Number D Pipe Size B Load Wt./100

in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kg)

909-3

/8 7

/16\" (11.1) 1\" (25) 15

/8\" (41.3) 1370 (6.09) 90 (40.8)

909-1

/2 * 17/32\" (13.5) 1\" (25) 15

/8\" (41.3) 1370 (6.09) 91 (41.3)

909-5

/8 11/16\" (17.5) 1\" (25) 15

/8\" (41.3) 1370 (6.09) 90 (40.8)

B

D

Mounting Hardware

Is Not Included

Set Bolt

Included

* Standard size.

OPM

Seismic Bracing

Seismic Bracing

63 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: 1\" (25mm) bracing pipe. For brace pipe sizes larger than 1\" (25mm),

use Fig. 980. Available with holes for 1

⁄2\" fastener attachment.

Material: Steel

Function: The Fig. 910, is the structural or transitional attachment component

of a longitudinal or lateral sway brace assembly. It is intended to combined with

a 1\" “bracing pipe”, and TOLCO™ “braced pipe” attachment to form a complete

bracing assembly. Sway brace assemblies are intended to be installed in

accordance with NFPA 13 and the manufacturer’s installation instructions

Features: This product’s design incorporates a concentric attachment opening

which is critical to the performance of structural seismic connections. NFPA 13

(2010) 9.3.5.8.4 and (2013-2016) 9.3.5.11.5 indicates that fastener table load

values are based only on concentric loading. Universal swivel design allows Fig.

910 to be attached at any surface angle.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada

(cUL). (cUL). UL Listed for the following brace member type pipes: Sch. 40.

Included in our Seismic Engineering Guidelines approved by the State of

California Office of Statewide Health Planning and Development (OSHPD). For

additional load, spacing and placement information relating to OSHPD projects,

please refer to our Seismic Engineering Guidelines,

OPM-0052-13.

Installation Instructions: Thread the 1\" brace pipe into the Fig. 910 until pipe

threads are visible through inspection site hole. When using in combination with

a Fig. 825A, Fig. 825, Fig. 828, or Fig. 906 refer to those instruction sheets,

otherwise select an anchor that is sized appropriately for the intended use and

follow anchor manufacturer’s instructions regarding structural thickness and

embedement requirements. The required type, number and size of fasteners used

for the structure attachment fitting shall be in accordance with NFPA 13. Once

the anchor is installed per the manufacturer’s direction, secure the Fig. 910 to the

anchor. Attachment can pivot for adjustment to proper brace angle.

Note: Fig. 910 swivel attachment and Fig. 1001, 2002, 3000 or 4L pipe clamps

make up a sway brace system of UL Listed attachments and bracing materials

which satisfies the requirements of Underwriters Laboratories and the National

Fire Protection Association (NFPA).

Finish: Electro-Galvanized. Contact customer service for alternative finishes and

materials.

Order By: Figure number, pipe size and finish.

F

E

C

A

B D

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 910 - threaded swivel sway brace attachment (UL listed)

Part Brace Mounting Max. Design Approx.

Number Pipe Size A B C Hole D E F Load Wt./100

in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kg)

910-1 X 1

/2 1\" (25) 17

/10\" (43.2) 11

/5\" (30.5) 215

/16\"(74.7) 9

/16\" (14.3) 111/16\" (42.9) 21

/20\" (52) 1600 (8.96) 105 (47.6)

B

A

D

F

E

C

Mounting Hardware

Is Not Included

OPM

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

64 Eaton B-Line series Fire Protection Solutions

Size Range: 1\" (25.4mm) x 1\" (25.4mm), 1\" (25.4mm) x 11

⁄4\" (31.7mm) and

11

⁄4\" (25.4mm) x 11

⁄4\" (25.4mm) bracing pipe.

Material: Steel, hardened cone (or cup) point set bolt

Function: For attaching two pieces of pipe together at various angles.

To Install: Attach the Fig. 907 over one piece of pipe and adjust to

desired position. Tighten set bolt until head bottoms out on surface, then

repeat the process for the second pipe.

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number, bracing pipe sizes and finish.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 907 - multi-angle attachment

Part Number Brace Pipe Size A B Max. Design Load Approx. Wt./100

in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kg)

907-1 X 1 1\" x 1\" (25 x 25) 43

/4\" (120.6) 43

/4\" (120.6) 655 (2.91) 103 (46.7)

907-1 X 11

/4 1\" x 11

/4\" (25 x 32) 53

/16\" (128.6) 413/16\" (122.2) 655 (2.91) 107 (48.5)

907-11

/4 X 11

/4 11

/4\" x 11

/4\" (32 x 32) 53

/8\" (136.5) 51

/4\" (133.1) 655 (2.91) 109 (49.4)

B

A

Set Bolts

Included

Fig. 1000

Brace Pipe

Shown

With

Fig. 909

Shown

With

Fig. 909

Shown

With

Fig. 909

Fig. 907 Can Be Attached On Either

Side Of The Pipe Being Braced

Fig. 1000

Fig. 907

Fig. 909

4-Way Riser Brace

Seismic Bracing

Seismic Bracing

65 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: 1\" (25mm) bracing pipe. For brace pipe sizes larger than 1\" (25mm), use

Fig. 980. Available with holes for 1

⁄2\", 5

⁄8\", or 3

⁄4\" fastener attachment.

Material: Steel

Function: The Fig. 975 is the structural or transitional attachment component of a

longitudinal or lateral sway brace assembly. It is intended to be combined with a 1\"

“bracing pipe” and TOLCO™ “braced pipe” attachment to form a complete bracing

assembly. Sway brace assemblies are intended to be installed in accordance with

NFPA 13 and the manufacturer’s installation instructions

Features: Open design allows for easy checking of thread engagement.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).

UL Listed for the following brace member type pipes: Sch. 40.

Installation: Thread the Fig. 975 onto the 1\" threaded bracing pipe. When using

in combination with the Fig. 906, refer to that instruction sheet, otherwise select

an anchor that is sized appropriately for the intended use and follow anchor

manufacturer’s instructions regarding structural thickness and embedment

requirements. The required type, number and size of fasteners used for the

structure attachment fitting shall be in accordance with NFPA 13. Once the anchor

is installed per the manufacturer’s direction, secure the Fig. 975 to the anchor.

Attachment can pivot for adjustment to proper brace angle. (Bending of plate not

permitted).

Finish: Plain or Electro-Galvanized. Contact customer service for alternative finishes

and materials.

Order By: Figure number and

finish.

Note: Bending of this fitting alters

the material strength and voids the

cULus Listing. Use Fig. 980, 910,

909, or any other TOLCO fitting

when angled fitting is required.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Lateral Brace

TOLCO Fig. 975 - straight sway brace fitting (UL listed)

Part Brace Mounting Hole Max. Design Approx.

Number Pipe Size A B C D Load Wt./100

in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kg)

975-1

/2 * 1\" (25) 4\" (101.6) 31

/2\" (88.9) 11

/2\" (38.1) 9

/16\" (14.3) 2100 (9.34) 88 (39.9)

975-5

/8 1\" (25) 4\" (101.6) 31

/2\" (88.9) 11

/2\" (38.1) 11/16\" (17.5) 2100 (9.34) 87 (39.4)

975-3

/4 1\" (25) 4\" (101.6) 31

/2\" (88.9) 11

/2\" (38.1) 13/16\" (20.6) 2100 (9.34) 86 (39.0)

B

D

C

A

Mounting Hardware

Is Not Included

* Standard size.

Fig. 975 Brace Pipe

Fig. 1001

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

66 Eaton B-Line series Fire Protection Solutions

Size Range: Pipe size to be braced: 1\" (25mm) thru 8\" (200mm) IPS.

Pipe size used for bracing: 1\" (25mm) and 11

⁄4\" (32mm) Schedule 40 IPS.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance. The pipe attachment

component of a sway brace system: Fig. 1001 is used in conjunction with a Fig. 900 Series

fitting and joined together with bracing pipe per NFPA 13, forming a complete sway brace

assembly.

Features: Can be used to brace schedule 7 through schedule 40 IPS. Field adjustable,

making critical pre-engineering of bracing pipe length unnecessary. Unique design requires no

threading of bracing pipe. Comes assembled and ready for installation. Fig. 1001 has

built-in visual verification of correct installation. See installation note below.

Installation Note: Position Fig. 1001 over the pipe to be braced and tighten two hex head

cone point set bolts until heads bottom out. A minimum of 1\" (25mm) pipe extension is

recommended. Brace pipe can be installed on top or bottom of pipe to be braced.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). UL Listed

for the following sprinkler type pipes: Sch. 40 (and as brace member), Sch. 10, Bull Moose

Eddy Flow, Wheatland Mega Flow, DIN 2448, KSD 3562 (and as brace member), KSD

3507. Ask the factory for additional information as it may vary by product size. Included in

our Seismic Engineering Guidelines approved by the State of California Office of Statewide

Health Planning and Development (OSHPD). For additional load, spacing and placement

information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13. For FM Approval information refer to FM Approved page 67.

Finish: Plain, Electro-Galvanized or Hot Dip Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Order by figure number, pipe size to be braced, followed by pipe size used for

bracing (1\" (25mm) or 11

⁄4\" (32mm)), and finish.

TOLCO Fig. 1001 - sway brace attachment (UL listed)

Set Bolts

Included

Pipe Part Number & Approx. Wt./100 Design Load - Lbs.

Size 1\" (25mm) Brace Pipe 11

/4\" (32mm) Brace Pipe For Brace Pipe Size 1\" / 11

/4\"

Sch. 7 Sch. 10 Sch. 40

in. (mm) Lbs. (kg) Lbs. (kg) 1\" / 11

/4\" 1\" / 11

/4\" 1\" / 11

/4\"

1\" (25) 1001-1 X 1 104.6 (47.4) 1001-1 X 11

/4 122.2 (55.4) — / — — / — 1000 / 1000

11

/4\" (32) 1001-11

/4 X 1 105.2 (47.7) 1001-11

/4 X 11

/4 122.6 (55.6) 1000 / 1000 1000 / 1000 1000 / 1000

11

/2\" (40) 1001-11

/2 X 1 107.0 (48.5) 1001-11

/2 X 11

/4 124.7 (56.6) 1500 / 1500 1500 / 1500 1500 / 1500

2\" (50) 1001-2 X 1 112.6 (51.1) 1001-2 X 11

/4 129.2 (58.6) 1500 / 1500 1500 / 1500 1500 / 1500

*21

/2\" (65) 1001-21

/2 X 1* 136.3 (61.8) 1001-21

/2 X 11

/4* 154.4 (70.0) 2000 / 2000 2000 / 2000 2000 / 2000

3\" (80) 1001-3 X 1 145.0 (65.8) 1001-3 X 11

/4 163.1 (74.0) 2000 / 2000 2000 / 2000 2000 / 2000

4\" (100) 1001-4 X 1 158.6 (71.9) 1001-4 X 11

/4 176.7 (80.1) 2000 / 2000 2000 / 2000 2000 / 2000

5\" (100) 1001-5 X 1 173.2 (78.6) 1001-5 X 11

/4 191.4 (86.8) — / — 2000 / 2000 2000 / 2000

*6\" (150) 1001-6 X 1* 190.0 (85.2) 1001-6 X 11

/4* 206.0 (93.4) 2000 / 2000 2000 / 2000 2000 / 2000

*8\" (200) 1001-8 X 1* 217.4 (111.5) 1001-8 X 11

/4* 265.3 (120.3) — / — 2000 / 2000 2000 / 2000

*Note: Metric sizes available for 65mm, 150mm, 200mm pipe size with 25mm and 32mm brace pipe size.

Contact the factory.

OPM

Fig. 1001

Seismic Bracing

Seismic Bracing

67 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: Pipe size to be braced: 1\" (25mm) thru 8\" (200mm) IPS. Pipe size used

for bracing: 1\" (25mm) and 11

⁄4\" (32mm) Schedule 40 IPS.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance. The pipe

attachment component of a sway brace system: Fig. 1001 is used in conjunction

with a Fig. 900 Series fitting and joined together with bracing pipe per NFPA 13,

forming a complete sway brace assembly.

Features: Can be used to brace schedule 7 through schedule 40 IPS. Field

adjustable, making critical pre-engineering of bracing pipe length unnecessary.

Unique design requires no threading of bracing pipe. Can be used as a component

of a four-way riser brace. Comes assembled and ready for installation. Fig. 1001

has built-in visual verification of correct installation. See installation note below.

Installation Note: Position Fig. 1001 over the pipe to be braced and tighten two

hex head cone point set bolts until heads bottom out. A minimum of 1\" (25mm)

pipe extension is recommended. Brace pipe can be installed on top or bottom of

pipe to be braced.

Approvals: Approved by Factory Mutual Engineering (FM). Included in our

Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to our

Seismic Engineering Guidelines, OPM-0052-13. For UL Listed information refer to

UL Listed page 66.

Finish: Plain, Electro-Galvanized or Hot Dip Galvanized. Contact customer service

for alternative finishes and materials.

Order By: Order by figure number, pipe size to be braced, followed by pipe size

used for bracing (1\" (25mm) or 11

⁄4\" (32mm)) , and finish.

Important Note: Fig. 1001 is precision manufactured to perform its function as

a critical component of a complete bracing assembly. To ensure performance,

the FM Approval requires that Fig. 1001 must be used only with other TOLCO™

bracing products. The Fig. 1001 is not intended for use with the Fig. 907

4-way Longitudinal Brace Attachment.

Designed to meet or exceed requirements of FM DS 2-8.

TOLCO Fig. 1001 - sway brace attachment (FM approved)

Set Bolts

Included

Design Load - For Sch. 7, Sch. 10, & Sch. 40 Pipe

Pipe Part Number & Approx. Wt./100 Allowable Horizontal Capacity (lbf) Per Installation1, 2, 3

Size 1\" (25mm) Brace Pipe 11

/4\" (32mm) Brace Pipe 30°-44° 45°-59° 60°-74° 75°-90°

in. (mm) Lbs. (kg) Lbs. (kg) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1\" (25) 1001-1 X 1 104.6 (47.4) 1001-1 X 11

/4 122.2 (55.4) 1800 (8.01) 2550 (11.34) 3120 (13.88) 3490 (15.52)

11

/4\" (32) 1001-11

/4 X 1 105.2 (47.7) 1001-11

/4 X 11

/4 122.6 (55.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59)

11

/2\" (40) 1001-11

/2 X 1 107.0 (48.5) 1001-11

/2 X 11

/4 124.7 (56.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59)

2\" (50) 1001-2 X 1 112.6 (51.1) 1001-2 X 11

/4 129.2 (58.6) 1230 (5.47) 1740 (7.74) 2140 (9.52) 2380 (10.59)

*21

/2\"(65) 1001-21

/2 X 1* 136.3 (61.8) 1001-21

/2 X 11

/4 * 154.4 (70.0) 800 (3.56) 1130 (5.03) 1380 (6.14) 1540 (6.85)

3\" (80) 1001-3 X 1 145.0 (65.8) 1001-3 X 11

/4 163.1 (74.0) 850 (3.78) 1200 (5.34) 1470 (6.54) 1640 (7.30)

4\" (100) 1001-4 X 1 158.6 (71.9) 1001-4 X 11

/4 176.7 (80.1) 850 (3.78) 1200 (5.34) 1470 (6.54) 1640 (7.30)

5\" (100) 1001-5 X 1 173.2 (78.6) 1001-5 X 11

/4 191.4 (86.8) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40)

*6\" (150) 1001-6 X 1* 190.0 (85.2) 1001-6 X 11

/4* 206.0 (93.4) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40)

*8\" (200) 1001-8 X 1* 217.4 (111.5) 1001-8 X 11

/4* 265.3 (120.3) 510 (2.27) 730 (3.25) 890 (3.96) 990 (4.40)

1 FM Approved when used with 1 or 11

/4 inch NPS Schedule 40 GB/T 3091,EN 10255H, or JIS G3451 steel pipe as the brace member.

2 Load rating for LW above refers to FM Approved Lightwall Pipe commonly referred to as “Schedule 7\". These ratings may also be

applied when EN 10220 and GB/T 8163 steel pipe.

3 Load rating for Schedule 10 above may be applied to GB/T 3092,EN 10255M and H, or JIS G3454, FM Approved Thinwall, or Schedule

40 steel pipes.

Note: See UL load ratings in UL Listed Design

Load chart shown under drawing.

*Note: Metric sizes available for 65mm, 150mm, 200mm

pipe size with 25mm and 32mm brace pipe size.

Contact the factory.

OPM

Fig. 1001

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

68 Eaton B-Line series Fire Protection Solutions

Size Range: Pipe size to be braced: 1\" (25mm) thru 4\" (100mm) 40 IPS.

Pipe size used for bracing: 1\" (25mm) and 11

⁄4\" (32mm) Schedule 40 IPS.

For pipe sizes larger than 2\" (500mm) please refer to TOLCO™ Fig. 1001.

Material: Steel

Function: A restraint device intended for lateral bracing.

Features: Field adjustable, making critical pre-engineering of bracing pipe

unnecessary. Unique design requires no threading of bracing pipe. Steel leaf

spring insert provided to assure installer and inspector necessary minimum

torque has been achieved.

Installation: Fig. 1000 is the “braced pipe” attachment component of a lateral

sway brace assembly. It is intended to be combined with the “bracing pipe”

and TOLCO structural attachment component, Fig. 980, 910, 909 or other

approved TOLCO component to form a complete bracing assembly. Follow

NFPA 13 guidelines.

To Install: Place the Fig. 1000 over the pipe to be braced, insert bracing pipe

through opening leaving a minimum of 1\" extension. Brace pipe can be installed

on top or bottom of pipe to be braced. Tighten hex nuts until leaf spring is flat.

It is recommended that the brace angle be adjusted before hex nuts are fully

tightened.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada

(cUL). Approved for use with engineered light wall sprinkler pipe up to 2\" as

a restraint device. Torque requirement is 6-8 ft./lbs. (8-10Nm). Included in our

Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to

our Seismic Engineering Guidelines, OPM-0052-13.

For FM Approval information refer to FM Approved page 69.

Application Note: Position Fast Clamp and tighten two hex nuts until leaf

spring flattens. A minimum of 1\" pipe extension beyond the Fig. 1000 is

recommended.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Order by figure number, pipe size to be braced, followed by pipe

size used for bracing (1\" (25mm) or 11

⁄4\" (32mm)) , and finish.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Lateral Brace

TOLCO Fig. 1000 - “Fast Clamp“ branch line restraint attachment (UL listed)

UL Listed Design Load

1\" (25mm) thru 2\" (50mm) pipe size 650 Lbs. (2.89kN)

Pipe Part Number & Approx. Wt./100

Size 1\" (24mm) Brace Pipe 11

/4\" (32mm) Brace Pipe

in. (mm) Lbs. (kg) Lbs. (kg)

1\" (25) 1000-1 X 1 71.6 (32.5) 1000-1 X 11

/4 75.8 (34.4)

11

/4\" (32) 1000-11

/4 X 1 74.8 (33.9) 1000-11

/4 X 11

/4 79.1 (35.9)

11

/2\" (40) 1000-11

/2 X 1 77.8 (35.3) 1000-11

/2 X 11

/4 82.1 (37.2)

2\" (50) 1000-2 X 1 84.1 (38.1) 1000-2 X 11

/4 88.4 (40.1)

Hardware

Included

OPM

Fig. 980

Fig. 1000

Seismic Bracing

Seismic Bracing

69 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: Pipe size to be braced: 1\" (25mm) thru 4\" (100mm) 40 IPS.

Pipe size used for bracing: 1\" (25mm) and 11

⁄4\" (32mm) Schedule 40 IPS.

For pipe sizes larger than 4\" (100mm) please refer to TOLCO™ Fig. 1001.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance.

Features: Field adjustable, making critical pre-engineering of bracing pipe

unnecessary. Unique design requires no threading of bracing pipe. Steel leaf

spring insert provided to assure installer and inspector necessary minimum

torque has been achieved.

Installation: Fig. 1000 is the “braced pipe” attachment component of a lateral

sway brace assembly. It is intended to be combined with the “bracing pipe”

and TOLCO structural attachment component, Fig. 980 or other approved

TOLCO seismic brace to form a complete bracing assembly. Follow NFPA 13

guidelines.

To Install: Place the Fig. 1000 over the pipe to be braced, insert bracing pipe

through opening leaving a minimum of 1\" extension. Brace pipe can be installed

on top or bottom of pipe to be braced. Tighten hex nuts until leaf spring is flat.

It is recommended that the brace angle be adjusted before hex nuts are fully

tightened.

Approvals: Approved by Factory Mutual Engineering (FM). Included in our

Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load,

spacing and placement information relating to OSHPD projects, please refer to

our Seismic Engineering Guidelines, OPM-0052-13. For UL Listed information

refer to UL Listed page 68.

Application Note: Position Fast Clamp and tighten two hex nuts until leaf

spring flattens. A minimum of 1\" pipe extension beyond the Fig. 1000 is

recommended.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Order by figure number, pipe size to be braced, followed by pipe

size used for bracing (1\" (25mm) or 11

⁄4\" (32mm)), and finish.

Designed to meet or exceed requirements of FM DS 2-8.

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Lateral Brace

TOLCO Fig. 1000 - “Fast Clamp‘’ sway brace attachment (FM approved)

Hardware

Included

1

FM Approved when used with 1, 11

/4, 11

/2, or 2 inch NPS Schedule 40 GB/T 3091,EN 10255H, or JIS G3451 steel pipe as the brace member.

2 Load rating for LW above refers to FM Approved Lightwall Pipe commonly referred to as “Schedule 7\". These ratings may also be applied when

EN 10220 and GB/T 8163 steel pipe.

3

Load rating for Schedule 10 above may be applied to GB/T 3092,EN 10255M and H, or JIS G3454, FM Approved Thinwall, or Schedule 40 steel pipes.

Pipe Part Number & Approx. Wt./100 Design Load - Allowable Horizontal Capacity (lbf) Per Installation 1, 2, 3

Size 1\" (24mm) Brace Pipe 11

/4\" (32mm) Brace Pipe 30°-44° 45°-59° 60°-74° 75°-90°

in. (mm) Lbs. (kg) Lbs. (kg) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1\" (25) 1000-1 X 1 71.6 (32.5) 1000-1 X 11

/4 75.8 (34.4) 200 (0.89) 280 (1.24) 340 (1.51) 380 (1.69)

11

/4\" (32) 1000-11

/4 X 1 74.8 (33.9) 1000-11

/4 X 11

/4 79.1 (35.9) 200 (0.89) 280 (1.24) 340 (1.51) 380 (1.69)

11

/2\" (40) 1000-11

/2 X 1 77.8 (35.3) 1000-11

/2 X 11

/4 82.1 (37.2) 200 (0.89) 280 (1.24) 340 (1.51) 380 (1.69)

2\" (50) 1000-2 X 1 84.1 (38.1) 1000-2 X 11

/4 88.4 (40.1) 200 (0.89) 280 (1.24) 340 (1.51) 380 (1.69)

21

/2\" (65) 1000-21

/2 X 1 90.2 (40.9) 1000-21

/2 X 11

/4 94.6 (42.9) 200 (0.89) 280 (1.24) 340 (1.51) 380 (1.69)

3\" (80) 1000-3 X 1 97.3 (44.1) 1000-3 X 11

/4 101.7 (46.1) 230 (1.02) 320 (1.42) 400 (1.78) 450 (2.00)

31

/2\" (90) 1000-31

/2 X 1 104.0 (47.2) 1000-31

/2 X 11

/4 108.4 (49.2) 230 (1.02) 320 (1.42) 400 (1.78) 450 (2.00)

4\" (100) 1000-4 X 1 110.3 (50.0) 1000-4 X 11

/4 114.6 (52.0) 230 (1.02) 320 (1.42) 400 (1.78) 450 (2.00)

OPM

Fig. 980

Fig. 1000

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

70 Eaton B-Line series Fire Protection Solutions

Size Range: Pipe size to be braced: 21

⁄2\" (65mm) thru 8\" (200mm) all steel

schedules. Consult factory when bracing other than steel. The Fig. 2002

accepts brace pipes sizes 11

⁄2\" (40mm) and 2\" (50mm) steel schedule 40.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance. The

pipe attachment component of a sway brace system: Fig. 2002 is used in

conjunction with a TOLCO™ Fig. 980 sway brace attachment and joined

together with bracing pipe. Install per NFPA 13.

Features: Easy verification of proper installation by tightening bolts until

ears touch.

Installation: Place Fig. 2002 over pipe to be braced. Slide bracing pipe

through attachment and tighten hex nuts until ears touch.

Approvals: Underwriters Laboratories Listed in the USA (UL) and

Canada (cUL). UL Listed for the following sprinkler type pipes: Sch. 40 (and

as brace member), Sch. 10, Bull Moose Eddy Flow, Wheatland Mega Flow,

DIN 2448, KSD 3562 (and as brace member), KSD 3507. Ask the factory for

additional information as it may vary by product size.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, pipe size to be braced, pipe size used for bracing

(11

⁄2\" (40mm) or 2\" (50mm)) and finish.

TOLCO Fig. 2002 - sway brace attachment (UL listed)

Shown with

Fig. 980

Fig. 2002

1\" (25.4mm)

Min.

Pipe Part Number & Approx. Wt./100 Design

Size 11

/2\" (32mm) Brace Pipe 2\" (50mm) Brace Pipe Load

in. (mm) Lbs. (kg) Lbs. (kg) Lbs. (kN)

21

/2\" (65) 2002-21

/2 X 11

/2 260 (117.9) 2002-21

/2 X 2 283.3 (128.6) 2000 (8.89)

3\" (80) 2002-3 X 11

/2 276 (125.2) 2002-3 X 2 299.4 (135.8) 2000 (8.89)

4\" (100) 2002-4 X 11

/2 303 (137.4) 2002-4 X 2 326.8 (148.2) 2000 (8.89)

6\" (150) 2002-6 X 11

/2 361 (163.7) 2002-6 X 2 385.0 (174.6) 2000 (8.89)

8\" (200) 2002-8 X 11

/2 416 (188.7) 2002-8 X 2 439.7 (199.4) 2000 (8.89)

Hardware

Included

Seismic Bracing

Seismic Bracing

71 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Function: Three recommended applications for this product:

• May be used as a branch line restraint for structural attachment to

anchor bolt, beam clamp, etc.

• May be used as an upper attachment with short hanger rod to omit

seismic bracing.

• May be used in a pitched or sloped roof application, to meet

requirements of NFPA 13 (2010) 9.1.2.6.

Refer to page 40 for more information and sizing.

TOLCO Fig. 75 - swivel attachment

Fig. 76 - TOLCO structural attachment for branch line restraint assembly (UL listed)

structural attachment for sway brace assembly (FM)

Function: Structural attachment for branch line restraint or sway brace assembly

Refer to pages 42 for UL Listed information and sizing.

Refer to pages 43 for FM information and sizing.

Fig. 77 - TOLCO structural attachment for branch line restraint assembly (UL listed)

structural attachment for sway brace assembly (FM)

Function: System attachment for branch line restraint or sway brace assembly

Refer to pages 44 for UL Listed information and sizing.

Refer to pages 45 for FM information and sizing.

TOLCO Fig. 3000 - CPVC sway brace attachment

Function: For bracing CPVC and steel pipe against sway and seismic

disturbance. The pipe attachment component of a sway brace system:

Fig. 3000 is used in conjunction with a Fig. 900 Series fitting and joined

together with bracing pipe per NFPA 13, forming a complete sway brace

assembly.

Refer to page 41 for more information and sizing.

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

72 Eaton B-Line series Fire Protection Solutions

TOLCO Fig. 98 - Rod Stiffener

TOLCO Fig. 98B - Rod Stiffener with Break-Off Bolt Head

Size Range: Secures 3

⁄8\"-16 thru 7

⁄8\"-9 hanger rod

Material: Steel

Function: Secures channel to hanger rod for vertical seismic bracing.

Approvals: Included in our Seismic Engineering Guidelines

approved by the State of California Office of Statewide Health Planning

and Development (OSHPD). For additional load, spacing and placement

information relating to OSHPD projects, please refer to our Seismic

Engineering Guidelines OPM-0052-13.

Finish: Electro Galvanized. Contact customer service for alternative

finishes and materials.

Weight: Approx. Wt./100: Fig. 98 - 11.8 Lbs. (5.3kg)

Fig. 98B - 12.7 Lbs. (5.7kg)

Order By: Figure number

Notes:

1.) Rod stiffeners are required only on hanger and

trapeze assemblies that have seismic bracing

attached at or within 6\" (152.4mm) of the rod.

A minimum of two rod stiffeners (Figure 98, 98B,

or SC228) must be installed.

2.) Recommended torque on Figure 98 and SC228

is 8 ft-lbs. (10.8Nm) or finger tight and one full

turn with a wrench.

Figure 98B has the break off bolt head.

Rod Stiffener Requirements

Rod Maximum Rod Length Maximum Spacing Between

Size Without Rod Stiffener Rod Stiffeners

3/8\" 19\" (482mm) 13\" (330mm)

1/2\" 25\" (635mm) 18\" (457mm)

5/8\" 31\" (787mm) 23\" (584mm)

3/4\" 37\" (940mm) 28\" (711mm)

7/8\" 43\" (1092mm) 33\" (838mm)

1\"* 50\" (1270mm) 38\" (965mm)

11/4\"* 60\" (1524mm) 43\" (1092mm)

Fig. SC228 - Hanger Rod Stiffener

Size Range: Secures 3

⁄8\"-16 thru 5

⁄8\"-11 hanger rod

Material: Steel

Function: Secures channel to hanger rod for vertical seismic bracing.

Slight distortion of the channel (strut) may occur upon

installation of rod stiffeners.

Finish: Electro Galvanized. Contact customer service for alternative

finishes and materials.

Weight: Approx. Wt./100: 21.0 Lbs. (9.5kg)

Order By: Figure part number

Note: Order channel separately

11

/2\"

(63.5)

3/8\"-16

Threads

SC228B

SC228BS

N228WO

Fig. 98B

Fig. 98

OPM

* Use with SC228 only.

Seismic Bracing

Seismic Bracing

73 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

TOLCO Fig. 4A - Pipe Clamp for Sway Bracing

Size Range: 21

/2\" (65mm) thru 8\" (200mm) pipe. For sizes smaller than

21

/2\" (65mm) use Fig, 4LA.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada

(cUL) 21

/2\" (65mm) thru 8\" (200mm).

Installation Instructions: Fig. 4A is the “braced pipe” attachment component

of a longitudinal, lateral or riser brace assembly. It is intended to be combine

with the “bracing pipe” and TOLCO transitional and structural attachment

component(s) to form a complete bracing assembly. NFPA 13 guidelines

should be followed.

To Install: Place the Fig. 4A over the pipe to be braced. Attach TOLCO

transitional fitting, either Fig. 980, 910 or 909, to the clamp ears. Tighten bolts

and nuts; torque requirement is a minimum of 50 ft./lbs. (68Nm).

Transitional fitting attachment can pivot for adjustment to proper brace angle.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, pipe size and finish

Note: Please refer to Fig. 4LA for longitudinal brace applications for

1\" (25mm) - 12\" (300mm) pipe sizes.

C

D

A

B

Longitudinal Brace

For

Laterial Brace

Refer to 4LA

Hardware Included

Pipe Max. Horizontal Approx.

Part Size A C D Bolt Design Load (UL) Wt./100

No. in. (mm) in. (mm) in. (mm) in. (mm) Size lbs. (kN) lbs. (kg)

4A-21

/2 21

/2\" (100) 7\" (177.8) 211/16\" (68.3) 3\" (76.2) 1

/2\"-13 1000 (4.45) 134 (60.8)

4A-3 3\" (80) 71

/2\" (190.5) 3\" (76.2) 35

/16\" (84.1) 1

/2\"-13 1000 (4.45) 150 (69.0)

4A-4 4\" (100) 81

/2\" (215.9) 33

/8\" (85.7) 311/16\" (93.7) 1

/2\"-13 1600 (7.11) 221 (100.2)

4A-5 5\" (125) 93

/4\" (247.6) 37

/8\" (98.4) 43

/8\" (111.1) 1

/2\"-13 1600 (7.11) 253 (114.7)

4A-6 6\" (150) 111

/2\" (292.1) 5\" (127.0) 51

/8\" (130.2) 1

/2\"-13 2015 (8.96) 513 (232.7)

4A-8 8\" (200) 131

/4\"(336.5) 611/16\" (169.9) 61

/8\" (155.6) 1

/2\"-13 2015 (8.96) 601 (272.6)

Fig. 980 Fig. 980

Fig. 4A DISCONTINUED

Seismic Bracing

Seismic Bracing

All dimensions in charts and

on drawings are in inches.

Dimensions shown in

parentheses are in millimeters

unless otherwise specified.

74 Eaton B-Line series Fire Protection Solutions

TOLCO Fig. 4L - sway brace attachment (UL listed)

Size Range: 1\" (25mm) through 8\" (200mm) IPS. 10\" (250mm) and 12\" (300mm) not

UL listed

Material: Steel and stainless steel.

Function: For bracing pipe against sway and seismic disturbance.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL) 1\"

(25mm) through 8\" (200mm) pipe. UL Listed for the following sprinkler type pipes:

Sch. 40, Sch. 10, Bull Moose Eddy Flow, Wheatland Mega Flow, DIN 2448, KSD

3562, KSD 3507. Ask the factory for additional information as it may vary by product

size. For FM Approval information refer to FM Approved page 75. Included in

our Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load, spacing

and placement information relating to OSHPD projects, please refer to our Seismic

Engineering Guidelines, OPM-0052-13.

Installation Instructions: Fig. 4L is the “braced pipe“ attachment component

of a longitudinal and lateral sway brace assembly. It is intended to be combined

with the “bracing pipe“ and TOLCO structural attachment component to form

a complete bracing assembly. NFPA 13 guidelines should be followed. (For

complete detailed instructions see instruction sheet IL309015EN).

To Install: Place the Fig. 4L over the pipe to be braced and tighten bolts. Then

engage “bracing pipe” into jaw opening and tighten set bolt until head snaps off.

Jaw attachment can pivot for adjustment to proper brace angle.

Finish: Plain, Electrogalvanized, Hot Dip Galvanized or Stainless Steel (only for

4\" & 6\" sizes).

Order By: Figure number, pipe size and finish.

Eaton’s B-Line series seismic bracing

components are designed to be

compatible only with other B-Line

series bracing components, resulting

in a listed seismic bracing assembly.

Eaton B-Line Division warranty for

seismic bracing components will

be the warranty provided in Eaton

B-Line Division standard terms and

conditions of sale made available by

Eaton, except that, in addition to the

other exclusions from Eaton B-Line

Division warranty, Eaton makes no

warranty relating to B-Line series

seismic bracing components that are

combined with products not provided

by Eaton.

D

A

CC

A

D

Set Bolt &

Hardware Included

OPM

Lateral

Brace

Longitudinal

Brace

With Plain &

Electrogalvanized Finish

With Hot Dip Galvanized &

Stainless Steel Finish

UL Max. Rec. Load PLN & EG.

Approx.

Part No.

Nom Pipe Size A (Max) C D Bolt Size Logitudinal Lateral

in. (mm) in. in. in. in. lbs. lbs. Wt./100 lbs.

4L-1 1 (25) 5 2 13

/8 1

/2-13 1000 1000 176

4L-11

/4 11

/4 (32) 52

/7 21

/16 15

/9 1

/2-13 1000 1000 182

4L-11

/2 11

/2 (40) 51

/2 21

/3 12

/3 1

/2-13 1000 1000 187

4L-2 2 (50) 62

/7 22

/3 2 1

/2-13 1600 1000 204

4L-21

/2 21

/2 — 67

/9 3 21

/3 1

/2-13 2000 1000 217

4L-65mm — (65) 67

/9 3 21

/3 1

/2-13 700 1000 214

4L-3 3 (80) 73

/7 31

/4 25

/8 1

/2-13 2000 1000 323

4L-31

/2 31

/2 (90) 8 31

/2 27

/8 1

/2-13 2000 1000 343

4L-4*** 4 (100) 83

/7 33

/4 31

/8 1

/2-13 2000** 1000 253

4L-5 5 — 95

/9 43

/8 35

/8 1

/2-13 2000** 1600* 314

4L-125mm — (125) 95

/9 43

/8 35

/8 1

/2-13 1200 1600* 314

4L-6*** 6 — 113

/7 51

/3 44

/7 1

/2-13 2000 1600* 540

4L-150mm — (150) 113

/7 51

/3 44

/7 1

/2-13 1200 1600* 538

4L-8 8 — 133

/5 62

/5 52

/3 1

/2-13 2000 2100* 645

4L-200mm — (200) 133

/5 62

/5 52

/3 1

/2-13 1400 2100* 643

4L-10**** 10 (254) 173

/5 81

/4 71

/4 1

/2-13 NA NA 1349

4L-12**** 12 (300) 193

/5 91

/4 81

/4 1

/2-13 NA NA 1526

* Only UL listed as a lateral brace for use with a 1\" (25mm) pipe as the brace member.

** Only UL listed as a longitudinal brace for use with a 1\" (25mm) thru 11

/2\" (40mm) pipe as the brace member.

*** Fig 4L-4 and Fig 4L-6 are only sizes available in stainless steel 316.

**** FM approved not UL listed.

Updated 4-2-21

Seismic Bracing

Seismic Bracing

75 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

TOLCO Fig. 4L - sway brace attachment (FM approved)

Size Range: 1\" (25mm) through 12\" (300mm) IPS.

Material: Steel.

Function: For bracing pipe against sway and seismic disturbance.

Approvals: Approved by Factory Mutual Engineering (FM), 1\" (25mm) through 12\"

(300mm) pipe. For UL Listed information refer to UL Listed page 74. Included in

our Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load, spacing

and placement information relating to OSHPD projects, please refer to our Seismic

Engineering Guidelines, OPM-0052-13.

Installation Instructions: Fig. 4L is the “braced pipe“ attachment component of a

longitudinal and lateral sway brace assembly. It is intended to be combined with the

“bracing pipe“ and TOLCO™ structural attachment component to form a complete

bracing assembly. NFPA 13 and/or FM guidelines should be followed.

To Install: Place the Fig. 4L over the pipe to be braced and tighten bolts. Then

engage “bracing pipe“ into jaw opening and tighten set bolt until head snaps off.

Jaw attachment can pivot for adjustment to proper brace angle. (For complete

detailed instructions see instruction sheet IL309015EN).

Finish: Plain, Electrogalvanized.

Order By: Figure number, pipe size and finish.

Designed to meet or exceed requirements of FM DS 2-8.

OPM

D

A

CC

D

Set Bolt &

Hardware Included

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing

assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made

available by Eaton, except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing

components that are combined with products not provided by Eaton.

Lateral

Brace

Longitudinal

Brace

With Plain &

Electrogalvanized Finish

Part No.

Nom Pipe

Size

in. (mm)

A

(Max)

in.

C

in.

D

in.

Bolt

Size

in.

FM Max. Rec. Load

Logitudinal

FM Max. Rec. Load

Lateral Approx.

30°-44°

lbs. (kN)

45°-59°

lbs. (kN)

60°-74°

lbs. (kN)

75°-90°

lbs. (kN)

30°-44°

lbs. (kN)

45°-59°

lbs. (kN)

60°-74°

lbs. (kN)

75°-90°

lbs. (kN)

Wt./100

lbs.

4L-1 1 (25) 5 2 13

/8 1

/2-13 1060 (4.72) 1160 (5.16) 1400 (6.23) 1500 (6.68) 1370 (6.10) 1940 (8.63) 2380 (10.59) 2650 (11.79) 176

4L-11

/4 11

/4 (32) 52

/7 21

/16 15

/9 1

/2-13 1060 (4.72) 1160 (5.16) 1400 (6.23) 1500 (6.68) 1370 (6.10) 1940 (8.63) 2380 (10.59) 2650 (11.79) 182

4L-11

/2 11

/2 (40) 51

/2 21

/3 12

/3 1

/2-13 740 (3.30) 1020 (4.54) 1250 (5.57) 920 (4.10) 1370 (6.10) 1940 (8.63) 2380 (10.59) 2650 (11.79) 187

4L-2 2 (50) 62

/7 22

/3 2 1

/2-13 740 (3.30) 1020 (4.54) 1250 (5.57) 920 (4.10) 1420 (6.32) 1990 (8.86) 2440 (10.86) 2720 (12.10) 204

4L-21

/2 21

/2 — 67

/9 3 21

/3 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 220

4L-65mm — (65) 67

/9 3 21

/3 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 218

4L-3 3 (80) 73

/7 31

/4 25

/8 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 323

4L-31

/2 31

/2 (90) 8 31

/2 27

/8 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 343

4L-4 4 (100) 83

/7 33

/4 31

/8 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 253

4L-5 5 — 95

/9 43

/8 35

/8 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 313

4L-125mm — (125) 95

/9 43

/8 35

/8 1

/2-13 520 (2.32) 650 (2.90) 790 (3.52) 1040 (4.63) 1410 (6.28) 1990 (8.86) 2440 (10.86) 2720 (12.10) 312

4L-6 6 — 113

/7 51

/3 44

/7 1

/2-13 870 (3.87) 1200 (5.34) 1460 (6.50) 1630 (7.26) 1560 (6.94) 2210 (9.84) 2710 (12.06) 3020 (13.44) 540

4L-150mm — (150) 113

/7 51

/3 44

/7 1

/2-13 870 (3.87) 1200 (5.34) 1460 (6.50) 1630 (7.26) 1560 (6.94) 2210 (9.84) 2710 (12.06) 3020 (13.44) 538

4L-8 8 — 133

/5 62

/5 52

/3 1

/2-13 1190 (5.30) 1440 (6.41) 1580 (7.03) 1750 (7.79) 1560 (6.94) 2210 (9.84) 2710 (12.06) 3020 (13.44) 645

4L-200mm — (200) 133

/5 62

/5 52

/3 1

/2-13 1190 (5.30) 1440 (6.41) 1580 (7.03) 1750 (7.79) 1560 (6.94) 2210 (9.84) 2710 (12.06) 3020 (13.44) 643

4L-10 10 (254) 173

/5 81

/4 71

/4 1

/2-13 1620 (7.21) 1660 (7.38) 1570 (6.98) 1740 (7.74) 1620 (7.21) 2300 (10.23) 2820 (12.54) 3140 (13.97) 1349

4L-12 12 (300) 193

/5 91

/4 81

/4 1

/2-13 1620 (7.21) 1660 (7.38) 1570 (6.98) 1740 (7.74) 1620 (7.21) 2300 (10.23) 2820 (12.54) 3140 (13.97) 1526

Updated 4-2-21

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

76 Eaton B-Line series Fire Protection Solutions

Size Range: 1\" (25mm) through 8\" (200mm) IPS.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance.

Approvals: For FM Approval information refer to FM Approved page 77.

Underwriters Laboratories Listed in the USA and Canada (cULus).

Included in our Seismic Engineering Guidelines approved by the State of

California Office of Statewide Health Planning and Development (OSHPD).

For additional load, spacing and placement information relating to OSHPD

projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13.

Installation Instructions: Fig. 4LA can be used as the system attachment

component of a longitudinal or lateral brace assembly. It is intended to be

combined with the “bracing member\" and TOLCO™ transitional attachment

and structural attachment to form a complete bracing assembly. For fire

sprinkler applications NFPA 13 guidelines should be followed.

To Install: Place the Fig. 4LA pipe clamp component over the pipe to be

braced and tighten down the break-off nuts until the hex head portion breaks

off to verify correct installation torque. Next engage brace member (pipe or

strut) with jaw component and tighten break-off head bolt until the hex head

breaks off to verify correct installation torque. Pivot jaw for correct angle and

attach to structure using TOLCO brand transitional attachment and structural

attachment.

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number, pipe size and finish.

TOLCO Fig. 4LA - In-Line Sway Brace Attachment (UL Listed)

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Pipe UL Max. Rec. Load Approx.

Part Size A C D Bolt Size Longitudinal Lateral Wt./100

No. in. (mm) in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kN) lbs. (kg)

4LA-1 1\" (25) 319/32\" (91.2) 15/16\" (33.5) 15/16\" (33.5) 3/8\"-16 1000 (4.45) NA (NA) 119 (54.0)

4LA-11/4 11/4\" (32) 329/32\" (99.3) 13/8\" (35.3) 13/8\" (35.3) 3/8\"-16 1000 (4.45) NA (NA) 123 (55.8)

4LA-11/2 11/2\" (40) 45/32\" (105.7) 11/2\" (38.5) 11/2\" (38.5) 3/8\"-16 1000 (4.45) NA (NA) 127 (57.6)

4LA-2 2\" (50) 511/32\" (135.6) 21/32\" (51.9) 21/16\" (51.9) 3/8\"-16 1000 (4.45) NA (NA) 142 (64.4)

4LA-21/2 21/2\" (65) 527/32\" (148.7) 25/16\" (58.5) 25/16\" (58.5) 3/8\"-16 1000 (4.45) NA (NA) 173 (78.5)

4LA-3 3\" (80) 61/2\" (164.9) 25/8\" (66.6) 25/8\" (66.6) 3/8\"-16 1000 (4.45) 1000 (4.45) 187 (84.8)

4LA-31/2 31/2\" (90) 7.407\" (188.1) 27/8\" (73.1) 27/8\" (73.1) 3/8\"-16 1000 (4.45) 1000 (4.45) 198 (89.8)

4LA-4 4\" (100) 713/32\" (190.8) 31/8\" (79.5) 31/8\" (79.5) 3/8\"-16 1000 (4.45) 1000 (4.45) 209 (94.8)

4LA-6 6\" (150) 105/8\" (269.9) 49/16\" (115.9) 49/16\" (115.9) 1/2\"-13 1600 (7.12) 1600 (7.12) 521 (236.3)

4LA-8 8\" (200) 1213/16\" (325.5) 59/16\" (143.7) 521/32\" (143.7) 1/2\"-13 2015 (7.12) 2015 (7.12) 629 (285.3)

4LA-10* 10\" (250) 161/2\" (419.1) 71/4\" (184.2) 71/4\" (184.2) 1/2\"-13 NA (NA) NA (NA) 1320 (598.7)

4LA-12* 12\" (300) 181/2\" (469.9) 81/4\" (209.6) 81/4\" (209.6) 1/2\"-13 NA (NA) NA (NA) 1496 (678.6)

4LA-1 thru 4LA-4

4LA-6 thru 4LA-12

Longitudinal

Brace

Lateral Brace

C

A

D

C

A D

OPM

Fig. 980

Fig. 4LA

Fig. 980

Brace

Brace

Fig. 4LA

* FM Approved but not UL Listed.

DISCONTINUED

Seismic Bracing

Seismic Bracing

77 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Longitudinal

Brace

Lateral

Brace

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Size Range: 1\" (25mm) through 12\" (300mm) IPS.

Material: Steel

Function: For bracing pipe against sway and seismic disturbance.

Approvals: Approved by Factory Mutual Engineering (FM), 1\" (25mm)

through 12\" (300mm) pipe.

For UL Listed information refer to UL Listed page 76.

Included in our Seismic Engineering Guidelines approved by the State of

California Office of Statewide Health Planning and Development (OSHPD).

For additional load, spacing and placement information relating to OSHPD

projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13.

Installation Instructions: Fig. 4LA can be used as the system attachment

component of a longitudinal or lateral brace assembly. It is intended to be

combined with the “bracing member\" and TOLCO™ transitional attachment

and structural attachment to form a complete bracing assembly. For fire

sprinkler applications NFPA 13 guidelines should be followed.

To Install: Place the Fig. 4LA pipe clamp component over the pipe to be

braced and tighten down the break-off nuts until the hex head portion breaks

off to verify correct installation torque. Next engage brace member (pipe or

strut) with jaw component and tighten break-off head bolt

until the hex head breaks off to verify correct installation torque. Pivot jaw

for correct angle and attach to structure using TOLCO brand transitional

attachment and structural attachment.

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number, pipe size and finish.

TOLCO Fig. 4LA - In-Line Sway Brace Attachment (FM Approved)

4LA-1 thru 4LA-4

4LA-6 thru 4LA-12

Pipe FM Max. Rec. Load Approx.

Longitudinal & Lateral**

Part Size A C D Bolt Size 30°-44° 45°-59° 60°-74° 75°-90° Wt./100

No. in. (mm) in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kN) lbs. (kg)

4LA-1 1\" (25) 319/32\" (91.2) 15/16\" (33.5) 15/16\" (33.5) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 119 (54.0)

4LA-11/4 11/4\" (32) 329/32\" (99.3) 13/8\" (35.3) 13/8\" (35.3) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 123 (55.8)

4LA-11/2 11/2\" (40) 45/32\" (105.7) 11/2\" (38.5) 11/2\" (38.5) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 127 (57.6)

4LA-2 2\" (50) 511/32\" (135.6) 21/32\" (51.9) 21/16\" (51.9) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 142 (64.4)

4LA-21/2 21/2\" (65) 527/32\" (148.7) 25/16\" (58.5) 25/16\" (58.5) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 173 (78.5)

4LA-3 3\" (80) 61/2\" (164.9) 25/8\" (66.6) 25/8\" (66.6) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 187 (84.8)

4LA-31/2 31/2\" (90) 7.407\" (188.1) 27/8\" (73.1) 27/8\" (73.1) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 198 (89.8)

4LA-4 4\" (100) 713/32\" (190.8) 31/8\" (79.5) 31/8\" (79.5) 3/8\"-16 680 (3.02) 970 (4.31) 1190 (5.29) 1320 (5.87) 209 (94.8)

4LA-6 6\" (150) 105/8\" (269.9) 49/16\" (115.9) 49/16\" (115.9) 1/2\"-13 1620 (7.20) Note 1 Note 3 Note 5 521 (236.3)

4LA-8 8\" (200) 1213/16\" (325.5) 59/16\" (143.7) 521/32\" (143.7) 1/2\"-13 1620 (7.20) Note 2 Note 4 Note 6 629 (285.3)

4LA-10 10\" (250) 161/2\" (419.1) 71/4\" (184.2) 71/4\" (184.2) 1/2\"-13 1620 (7.20) Note 2 Note 4 Note 6 1320 (598.7)

4LA-12 12\" (300) 181/2\" (469.9) 81/4\" (209.6) 81/4\" (209.6) 1/2\"-13 1620 (7.20) Note 2 Note 4 Note 6 1496 (678.6)

** Longitudinal and Lateral Loads are the same except where noted in chart.

Note 1: Longitudinal Load 2260 lbs. (10.05kN) - Lateral Load 2300 lbs. (10.23kN)

Note 2: Longitudinal Load 1660 lbs. (7.38kN) - Lateral Load 2300 lbs. (10.23kN)

Note 3: Longitudinal Load 2010 lbs. (8.94kN) - Lateral Load 2820 lbs. (12.54kN)

Note 4: Longitudinal Load 1570 lbs. (6.98kN) - Lateral Load 2820 lbs. (12.54kN)

Note 5: Longitudinal Load 2220 lbs. (9.87kN) - Lateral Load 3140 lbs. (13.96kN)

Note 6: Longitudinal Load 1740 lbs. (7.74kN) - Lateral Load 3140 lbs. (13.96kN)

C

A

D

C

A D

OPM

Fig. 4LA

Fig. 4LA

Fig. 980 Fig. 980

Brace

Brace DISCONTINUED

Seismic Bracing

Seismic Bracing

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

78 Eaton B-Line series Fire Protection Solutions

Size Range: 3

⁄4\" (20mm) to 8\" (200mm) pipe

Material: Steel

Function: For bracing pipe against sway and seismic disturbance

Approvals: Included in our Seismic Engineering Guidelines approved by the State

of California Office of Statewide Health Planning and Development (OSHPD). For

additional load, spacing and placement information relating to OSHPD projects,

please refer to our Seismic Engineering Guidelines, OPM-0052-13.

Standard Finish: Plain or Electro-Plated, Contact customer service for alternative

finishes and materials.

Ordering: Specify part number and finish.

Installation Instructions: Fig. 4B is the “braced pipe” attachment component of

a longitudinal or lateral sway brace assembly. It is intended to be combined with

the “bracing pipe” and transitional and structural attachment component(s) to form

a complete bracing assembly. OSHPD guidelines should be followed.

To Install: Place the Fig. 4B over the pipe to be braced. Attach other transitional

fitting, Fig. 909, 910, 980, or 990. Tighten bolts and nuts. Transitional fitting

attachment can pivot for adjustment to proper brace angle.

TOLCO Figure 4B pipe clamp

Pipe Size Rod Size B C D Bolt Size Approx. Wt./100

Part No. in. (mm) A in. (mm) in. (mm) in. (mm) Lbs. (kg)

4B-3

/4 3

/4\" (20) 3

/8\"-16 1\" (25.4) 27

/8\" (73.0) 25

/8\" (66.7) 5

/16\"-18 56 (25.4)

4B-1 1\" (25) 3

/8\"-16 1\" (25.4) 31

/4\" (82.5) 215/16\" (74.6) 5

/16\"-18 60 (27.2)

4B-11

/4 11

/4\" (32) 3

/8\"-16 1\" (25.4) 39

/16\" (90.6) 31

/4\" (82.5) 5

/16\"-18 74 (33.5)

4B-11

/2 11

/2\" (40) 3

/8\"-16 1\" (25.4) 313/16\" (96.8) 37

/16\" (87.3) 5

/16\"-18 79 (35.8)

4B-2 2\" (50) 3

/8\"-16 11

/2\" (38.1) 51

/8\" (130.2) 45

/8\" (117.5) 5

/16\"-18 156 (70.7)

4B-21

/2 21

/2\" (65) 1

/2\"-13 13

/4\" (44.4) 55

/8\" (142.9) 53

/8\" (136.5) 3

/8\"-16 176 (79.8)

4B-3 3\" (80) 1

/2\"-13 17

/8\" (47.6) 63

/4\" (171.4) 61

/8\" (155.5) 3

/8\"-16 198 (89.9)

4B-31

/2 31

/2\" (90) 1

/2\"-13 2\" (50.8) 71

/4\" (184.1) 63

/4\" (171.4) 3

/8\"-16 219 (99.3)

4B-4 4\" (100) 5

/8\"-11 2\" (50.8) 85

/8\" (219.1) 71

/4\" (184.1) 1

/2\"-13 288 (130.6)

4B-5 5\" (125) 5

/8\"-11 2\" (50.8) 97

/8\" (250.8) 85

/16\" (211.1) 5

/8\"-11 390 (176.9)

4B-6 6\" (150) 3

/4\"-10 21

/8\" (54.0) 1015/16\" (277.8) 91

/2\" (241.3) 5

/8\"-11 448 (203.2)

4B-8 8\" (200) 7

/8\"-9 21

/8\" (54.0) 137

/16\" (341.2) 111

/2\" (292.1) 3

/4\"-10 691 (313.4)

B

D

C

A

Fig. 980

Fig. 980

Fig. 4B

Hanger/Longitudinal Brace

OPM

Eaton’s B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components,

resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty

provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton, except that, in addition to the other

exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are

combined with products not provided by Eaton.

Refer to OPM-0052-13 for approved loads.

Concrete Anchors

79 B-Line series Fire Protection Solutions Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Concrete Anchors

Features:

• Fully threaded, torque-controlled, wedge anchor which is

designed for consistent performance in cracked and

uncracked concrete.

• For use in concrete, structural sand lightweight concrete,

and concrete over metal deck.

• Nominal drill bit size is the same as the anchor diameter.

• ICC-ES listed, ESR-2502, Category 1

• Zinc plated carbon steel body with stainless steel expansion

clip from premium performance.

• Qualified for seismic and wind loading.

Approvals: Included in our Seismic Engineering Guidelines approved by

the State of California Office of Statewide Health Planning and Development

(OSHPD). For additional load, spacing and placement information relating to

OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13.

ICC-ES Certified. See ICC-ESR-2502

UL (Underwriters Laboratories) Listed

FM (Factory Mutual) Approved

Refer to pages 11-20 through 11-23 in Seismic Engineering Guidelines

OPM-0052-13 for approval OSHPD structural attachment data.

AWSD Series - Power Stud+®†

SD2 seismic wedge anchors

Anchor Size

Wedge Anchor Diameter Length Thread Length Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)

AWSD-37-300 3

/8\" (9.5) 3\" (76.2) 13

/4\" (44.4) 11.4 (5.2)

AWSD-37-350 3

/8\" (9.5) 31

/2\" (88.9) 21

/4\" (57.1) 12.2 (5.5)

AWSD-37-375 3

/8\" (9.5) 33

/4\" (95.2) 21

/2\" (63.5) 13.2 (6.0)

AWSD-37-500 3

/8\" (9.5) 5\" (127.0) 33

/4\" (95.2) 16.0 (7.2)

AWSD-50-375 1

/2\" (12.7) 33

/4\" (95.2) 21

/8\" (54.0) 23.0 (10.4)

AWSD-50-450 1

/2\" (12.7) 41

/2\" (114.3) 27

/8\" (73.0) 26.6 (12.0)

AWSD-50-550 1

/2\" (12.7) 51

/2\" (139.7) 37

/8\" (98.4) 34.0 (15.4)

AWSD-50-700 1

/2\" (12.7) 7\" (177.8) 53

/8\" (136.5) 38.0 (17.2)

AWSD-62-475 5

/8\" (15.9) 43

/4\" (120.6) 27

/8\" (73.0) 50.3 (22.8)

AWSD-62-500 5

/8\" (15.9) 5\" (127.0) 31

/8\" (79.4) 52.0 (23.6)

AWSD-62-600 5

/8\" (15.9) 6\" (152.4) 41

/8\" (104.8) 58.8 (26.7)

AWSD-62-700 5

/8\" (15.9) 7\" (177.8) 51

/8\" (130.2) 65.2 (29.6)

AWSD-75-550 3

/4\" (19.0) 51

/2\" (139.7) 31

/4\" (82.5) 81.5 (36.9)

AWSD-75-625 3

/4\" (19.0) 61

/4\" (158.7) 4\" (101.6) 94.0 (42.6)

AWSD-75-700 3

/4\" (19.0) 7\" (177.8) 43

/4\" (120.6) 106.5 (48.3)

For loading information, refer to the ICC-ES ESR-2502 evaluation report.

Seismic Wedge Anchor - Data 3

/8\"-16 1

/2\"-13 5

/8\"-11 3

/4\"-10

ANSI Drill Bit Size (in. - mm) 3

/8\" - (9.5mm) 1

/2\" - (12.7mm) 5

/8\" - (15.9mm) 3

/4\" - (19.0mm)

Fixture Clearance Hole (in. - mm) 7

/16\" - (11.1mm) 9

/16\" - (14.3mm) 11/16\" - (17.5mm) 13/16\" - (20.6mm)

Minimum Hole Depth (in. - mm) 25

/8\" - (66.7mm) 23

/4\" - (69.8mm) 41

/4\" - (107.9mm) 5\" - (127.0mm)

Minimum Concrete Thickness (in. - mm) 4\" - (101.6mm) 41

/2\" - (114.3mm) 53

/4\" - (146.0mm) 7\" - (177.8mm)

Max. Tightening Torque (lbs-ft - N•m) 20 lbs-ft - (27.1N•m) 40 lbs-ft - (54.2N•m) 60 lbs-ft - (81.3N•m) 110 lbs-ft - (149.1N•m)

Min. Embedment Depth (in. - mm) 23

/8\" - (60.3mm) 21

/2\" - (63.5mm) 37

/8\" - (98.4mm) 41

/2\" - (114.3mm)

OPM

†

Power Stud+® SD2 is a registered trademark used by DeWalt.

Concrete Anchors

Concrete Anchors

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

80 Eaton B-Line series Fire Protection Solutions

TOLCO Fig. 109DD - DDI+™†

- concrete deck insert - hanger application

NOTES:

1. Mounting holes are standard. If the plate is not mechanically secured to the deck ribs, a jam nut is required to prevent the

anchor bolt from laying over when concrete is poured. There is no structural strength added from the use of a mechanical

fastener to hold the product in place before the pour.

2. Minimum spacing between inserts shall be not less than 3 times the embedment depth or 12 times the anchor diameter

(whichever is greater)

16\" (406mm) x Anchor Dia.

Minimum

‘D’ ‘D’ ‘D’

Edge of Concrete

Edge of Concrete

Edge of Concrete

Fig. 109DD Fig. 109DD Fig. 109DD

16\" (406mm) x Anchor Dia.

Minimum

3

/4\" (19.0mm)

Minimum

11

/4\" 31.8mm)

Minimum

3

/4\" (19.0mm)

Minimum

3

/4\" (19.0mm)

Minimum

16\" (406mm) x Anchor Dia.

Minimum

1î

A

Fig. 109DD

‘D’ 3

/4\" (19.0mm)

Minimum

Size Range: 3

/8\"-16 thru 7

/8\"-9 rod

Material: Steel

Function: For use in concrete filled metal deck (20 GA. min.)

assemblies (i.e. pan deck, Q-deck) applications. After installation, the

threaded male hanger of the insert protrudes below the surface of

the deck. The threaded bolt offers adjustability for precise height

requirements and guarantees the minimum embedment depth. The

longer plate enables a variety of installation locations across the deck.

Pre-mounted drill screws included for installation.

Approvals: International Code Council, Evaluation Service (ICC-ES),

ESR-3958 for concrete, for 3

/8\"-16 thru 5

/8\"-11\" anchor sizes.

Approved for seismic and wind loading.

UL (Underwriters Laboratories) Listed

FM (Factory Mutual) Approved

Finish: Plate: Plain Steel. Rod: Electro-Galvanized.

Order By: Figure number, rod size and finish.

Applications Per NFPA 13 (2010): UL Listed as a component of a

hanger assembly per Section 9.1.1.4.1

See dimensions and installation Detail below.

Note: Fig. 109DD replaces Fig. 109A which has been discontinued.

Bolt Length

8\" (203.2mm)

12\"

(304.8mm)

T

W

†

DDi+™ is a registered trademark used by DEWALT®

Rod Max. Vertical ‘D’ Min. Anchor Approx.

Size T W Load Embedment Depth Wt./100

Part No. in. (mm) in. (mm) lbs. (kn) in. (mm) lbs. (kg)

109DD-3

/8 3

/8\"-16 3

/16\" (4.7) 11

/4\" (31.7) 467 (2.08) 21

/2\" (63.5) 98.1 (44.5)

109DD-1

/2 1

/2\"-13 3

/16\" (4.7) 11

/4\" (31.7) 680 (3.02) 21

/2\" (63.5) 112.8 (51.1)

109DD-5

/8 5

/8\"-11 3

/16\" (4.7) 11

/4\" (31.7) 647 (2.88) 21

/2\" (63.5) 139.3 (63.2)

109DD-3

/4 3

/4\"-10 3

/8\" (9.5) 2\" (50.8) 612 2.72) 21

/2\" (63.5) 112.8 (153.6)

109DD-7

/8 7

/8\"-9 3

/8\" (9.5) 2\" (50.8) 577 (2.56) 21

/2\" (63.5) 381.2 (172.9)

Concrete Anchors

81 B-Line series Fire Protection Solutions Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Concrete Anchors

TOLCO Fig. 109DD-DDI+™†

- concrete deck insert - brace application

NOTES:

1. Mounting holes are standard. If the plate is not mechanically secured to the deck ribs, a jam nut is required to prevent the

anchor bolt from laying over when concrete is poured. There is no structural strength added from the use of a mechanical

fastener to hold the product in place before the pour.

2. Minimum spacing between inserts shall be not less than 3 times the embedment depth or 12 times the anchor diameter

(whichever is greater)

16\" (406mm) x Anchor Dia.

Minimum

‘D’ ‘D’ ‘D’ Edge of Concrete

Edge of Concrete

Edge of Concrete

Fig. 109DD Fig. 109DD Fig. 109DD

16\" (406mm) x Anchor Dia.

Minimum

3

/4\" (19.0mm)

Minimum

11

/4\" (25.4mm)

Minimum

3

/4\" (19.0mm)

Minimum

3

/4\" (19.0mm)

Minimum

16\" (406mm) x Anchor Dia.

Minimum

Detail 1 Detail 2 Detail 3

Size Range: 3

/8\"-16 thru 7

/8\"-9 rod

Material: Steel

Function: For use in concrete filled metal deck (20 GA. min.) assemblies (i.e.

pan deck, Q-deck) applications. After installation, the threaded male hanger of

the insert protrudes below the surface of the deck. The threaded bolt offers

adjustability for precise height requirements and guarantees the minimum

embedment depth. The longer plate enables a variety of installation locations

across the deck. Pre-mounted drill screws included for installation.

Approvals: International Code Council, Evaluation Service (ICC-ES),

ESR-3958 for concrete, for 3

/8\"-16 thru 5

/8\"-11\" anchor sizes.

Approved for seismic and wind loading.

UL (Underwriters Laboratories) Listed

FM (Factory Mutual) Approved

Finish: Plate: Plain Steel. Rod: Electro-Galvanized.

Order By: Figure number, rod size and finish.

Applications Per NFPA 13 (2010): UL Listed as a component of a hanger

assembly per Section 9.1.1.4.1

See dimensions and installation Detail below.

Note: Fig. 109DD replaces Fig. 109A which has been discontinued.

†

DDi+™ is a registered trademark used by DEWALT®

Bolt Length

8\" (203.2mm)

12\"

(304.8mm)

T

W

Seismic bracing design load calculated in compliance with the requirements of IBC 2015 / CBC 2016.

Details 1 & 2 Detail 3

Rod T W Max. Horizontal Load Max. Horizontal Load ‘D’ Min. Anchor Approx.

Size Brace At 45° Brace At 45° Embedment Depth Wt./100

Part No. in. (mm) in. (mm) lbs. (kN) lbs. (kN) in. (mm) lbs. (kg)

109DD-3

/8 3

/8\"-16 3

/16\" (4.7) 11

/4\" (31.7) 311 (1.38) 257 (1.14) 21

/2\" (63.5) 98.1 (44.5)

109DD-1

/2 1

/2\"-13 3

/16\" (4.7) 11

/4\" (31.7) 424 (1.89) 332 (1.48) 21

/2\" (63.5) 112.8 (51.1)

109DD-5

/8 5

/8\"-11 3

/16\" (4.7) 11

/4\" (31.7) 482 (2.14) 363 (1.61) 21

/2\" (63.5) 139.3 (63.2)

109DD-3

/4 3

/4\"-10 3

/8\" (9.5) 2\" (50.8) 482 (2.14) 363 (1.61) 21

/2\" (63.5) 338.7 (153.6)

109DD-7

/8 7

/8\"-9 3

/8\" (9.5) 2\" (50.8) 482 (2.14) 363 (1.61) 21

/2\" (63.5) 381.2 (172.9)

Concrete Anchors

Concrete Anchors

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

82 Eaton B-Line series Fire Protection Solutions

Features:

• Wood-Knocker™ II concrete inserts are installed onto wooden

forms used to support newly poured concrete floor slabs, roof

slabs or walls.

• When the forms are stripped, the color-coded flange is

visibly embedded in the concrete surface.

• The unique, six sided impact plate offers resistance to rotation

within the concrete as threaded rod is being installed.

• Suitable for overhead installations such as suspending cable

tray, pipe hangers, strut and conduit.

• Color coded by size for all trades.

• UL and FM approved.

• Lowest installation cost.

Approvals: Qualified for static, wind, and seismic loading in concrete.

Included in our Seismic Engineering Guidelines approved by the State

of California Office of Statewide Health Planning and Development

(OSHPD). For additional load, spacing and placement information

relating to OSHPD projects, please refer to our Seismic Engineering

Guidelines, OPM-0052-13.

ICC-ES Certified. See ICC-ESR-3657

UL (Underwriters Laboratories) Listed

FM (Factory Mutual) Approved

Refer to pages 11-26 through 11-27 in Seismic

Engineering Guidelines OPM-0052-13 for approval OSHPD

structural attachment data.

ACPW Series - Wood-Knocker™†

II

* Based on normal weight concrete with minimum compression strength of 3000 psi.

Allowable load capacities are calculated using applied safety factor of 4.0.

For additional loading information contact factory.

Minimum embedment depth is 2\".

Wood Knocker™ - Data 1

/4\" 3

/8\" 1

/2\" 5

/8\" 3

/4\"

Insert Thread Length (in.) 3

/8 5

/8 11/16 15/16 11

/8

Plastic Flange Diameter (in.) 13

/8 13

/8 13

/8 15

/8 15

/8

Thread Size (UNC) 1

/4\"-20 3

/8\"-16 1

/2\"-13 5

/8\"-11 3

/4\"-10

Overall Length (in.) 17

/8 17

/8 17

/8 17

/8 17

/8

Min. Insert Spacing (in.) 9 9 9 12 12

Min. End Distance (in.) 6 6 6 9 9

Load Capacity Tension (lbs) * 930 1200 1200 1160 1160

Load Capacity Shear (lbs) * 370 1330 1840 2800 2800

Catalog Rod Color

Number Diameter

ACPW-25-2 1

/4\" Brown

ACPW-37-2 3

/8\" Green

ACPW-3750-2 3

/8\"-1

/2\" Gray

ACPW-50-2 1

/2\" Yellow

ACPW-62-2 5

/8\" Red

ACPW-75-2 3

/4\" Purple

†

Wood-Knocker™ is a registered trademark used by DeWalt.

ACPW-50

shown

OPM

Concrete Anchors

83 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Concrete Anchors

Features:

• Bang-It™+ concrete inserts are designed for installation in and through metal

composite deck used to support newly poured concrete floors or roof slabs.

• After installation, the protective sleeve of the insert protrudes below the

surface of the deck, allowing overhead attachment of threaded rod.

• The unique, six sided impact plate offers resistance to rotation within the

concrete as threaded rod is bing installed.

• Suitable for overhead installations such as suspending cable tray,

pipe hangers, strut and conduit.

• Color coded by size for all trades.

• Lowest installation cost.

Approvals: Qualified for static, wind, and seismic loading in concrete. Included in

our Seismic Engineering Guidelines approved by the State of California Office of

Statewide Health Planning and Development (OSHPD). For additional load, spacing

and placement information

relating to OSHPD projects, please refer to our Seismic Engineering Guidelines,

OPM-0052-13.

ICC-ES Certified. See ICC-ESR-3657

UL (Underwriters Laboratories) Listed

FM (Factory Mutual) Approved

Refer to pages 11-28 through 11-32 in Seismic Engineering Guidelines

OPM-0052-13 for approval OSHPD structural attachment data.

ACPD Series - Bang-It™†

+ anchors

* Based on sand lightweight and normal weight concrete with minimum compression strength of 3000 psi over steel deck.

Allowable load capacities are calculated using applied safety factor of 4.0.

For additional loading information contact factory.

Minimum insert spacing of 6\", minimum end spacing 6\".

Bang-It™ - Data 1

/4\" 3

/8\" 1

/2\" 5

/8\" 3

/4\"

Metal Hole Saw Diameter (in.) 13/16 13/16 13/16 13

/16 13

/16

Drilling Speed (rpm) 700-900 700-900 700-900 500-700 500-700

Insert Thread Length (in.) 3

/8 5

/8 11/16 15/16 11

/8

Length of Sleeve (in.) 33

/8 33

/8 33

/8 33

/8 33

/8

Thread Size (UNC) 1

/4\"-20 3

/8\"-16 1

/2\"-13 5

/8\"-11 3

/4\"-10

Embedment Depth (in.) 2 2 2 2 2

Upper Deck Tension Load (lbs) * 1115 1915 2370 2935 2935

Lower Deck Tension Load (lbs) * 830 830 830 930 990

Upper Deck Shear Load (lbs) * 835 1115 1115 1115 1115

Lower Deck Shear Load (lbs) * 625 840 840 840 840

Catalog Rod Color

Number Diameter

ACPD-25 1

/4\" Brown

ACPD-37 3

/8\" Green

ACPD-3750-2 3

/8\"-1

/2\" Gray

ACPD-50 1

/2\" Yellow

ACPD-62 5

/8\" Red

ACPD-75 3

/4\" Purple

Catalog

Number Description

ACPD-HS813-2 13/16\" Carbide Hole Saw for 1

/4\", 3

/8\", 1

/2\"

ACPD-HS1188-2 13

/16\" Carbide Hole Saw for 5

/8\", 3

/4\"

†

Bang-It™ is a registered trademark used by DeWalt

OPM

Concrete Anchors

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

84 Eaton B-Line series Fire Protection Solutions

Concrete Anchors

Features:

• For use in normal-weight concrete, structural sand lightweight concrete and concrete over metal deck.

• Anchor design allows for shallow embedment and mechanically interlocks with base material.

• Internally threaded anchor for easy adjustment and removability of threaded rod or bolt.

• Fast anchor installation with a powered impact wrench.

• Suitable for overhead applications such as suspending cable tray, strut, pipe hangers and conduit.

• Made of Zinc Plated carbon steel.

• Setting tool included.

• Approvals: ICC-ES certified. See ICC-ESR-2272.

FM (Factory Mutual) Approved

ATM Series - self-tapping machine screw anchors

Self-Tapping Machine Screw Anchor - Data 3

/8\"

ANSI Drill Bit Size (in. - mm) 1

/2\" - (12.7mm)

Minimum Concrete Thickness (in. - mm) 4\" - (101.6mm)

Max. Tightening Torque (lbs-ft - N•m) 8 lbs-ft - (10.8N•m)

Min. Embedment Depth (in. - mm) 13

/8\" - (41.3mm)

Load Capacity Tension (lbs - kN)** 540 lbs - (2.40kN)

Load Capacity Shear (lbs - kN)** 825 lbs - (3.67kN)

**Based on concrete compression strength of 4000 psi

in uncracked concrete using applied safety factor of

4.0. For additional loading information contact factory.

For ultimate strength design data in cracked and

uncracked concrete, refer to ICC-ES ESR-2272

evaluation report.

Anchor Thread Size Thread Length Wt./100

Part No. in. (mm) lbs. (kg)

ATM-37 3

/8\"-16 11/16\" (17.6) 5.2 (2.3)

Features:

• For use in racking, shelving, material handling, structural anchorage, masonry AND food

& beverage facilities.

• One piece heavy-duty anchor with a finished hex-head.

• Fits standard fixture hole dimensions in fabricated steel.

• Fast installation and immediate loading reduces downtime.

• For proper performance, screw anchors must be installed with the corresponding bits.

The bits have a matched tolerance range designed to provide optimum performance.

ACB Series - concrete screw bolts

* Based on concrete compression strength of 4000 psi in uncracked concrete using applied safety factor of

4.0. For additional loading information contact factory.

For ultimate strength design data in cracked and uncracked concrete, refer to ICC-ES ESR-3889 evaluation report.

Concrete Bolt Diameter Length Thread Length Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)

ACB-25-175-2 1

/4\" (6.3) 13

/4\" (44.4) 15

/8\" (41.3) 3.5 (1.6)

ACB-25-225-2 1

/4\" (6.3) 21

/4\" (57.1) 2\" (50.8) 4.2 (1.9)

ACB-25-300-2 1

/4\" (6.3) 3\" (76.2) 23

/4\" (69.8) 5.0 (2.3)

ACB-37-175-2 3

/8\" (9.5) 13

/4\" (44.4) 11

/2\" (38.1) 7.8 (3.5)

ACB-37-250-2 3

/8\" (9.5) 21

/2\" (63.5) 21

/4\" (57.1) 10.2 (4.6)

ACB-37-300-2 3

/8\" (9.5) 3\" (76.2) 23

/4\" (69.8) 11.6 (5.3)

ACB-37-400-2 3

/8\" (9.5) 4\" (101.6) 33

/4\" (95.2) 14.8 (6.7)

Concrete Screw Bolts - Data 1

/4\" 3

/8\"

ACB Drill Bit Size (in. - mm) 1

/4\" - (6.3mm) 3

/8\" - (9.5mm)

Concrete Screw Tolerance Range (in. - mm) 0.255\" - 0.259\" - (6.5mm - 6.6mm) 0.385\" - 0.389\" - (9.8mm - 9.9mm)

Min. Embedment Depth (in. - mm) 1\" - (25.4mm) 11

/2\" - (38.1mm)

Load Capacity Tension (lbs - kN) * 335 lbs. - (1.49kN) 630 lbs. - (2.80kN)

Load Capacity Shear (lbs - kN) * 520 lbs. - (2.31kN) 1170 lbs. - (5.20kN)

Brackets

85 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Brackets

B3065 - Welded bracket - light duty

Max. Recommended Load: 275 lbs. (1.22kN)

Material: Steel

Function: Recommended for supporting pipe on top or

hanging through support bracket outward from mounting

surface.

Approvals: Conforms to Federal Specification WW-H-171E

& A-A-1192A, Type 32 and Manufacturers Standardization

Society ANSI/MSS SP-69 & SP-58, Type 31.

Finish: Plain

Note: Available in Electro-Galvanized and HDG finish or

Stainless Steel materials.

Order By: Figure number and finish

1\"

(25.4)

C

A

B

B3068 - Welded bracket - light duty

Material: Steel

Function: Recommended for suspending pipe outward from

mounting surface.

Approvals: Conforms to Federal Specification WW-H-171E &

A-A-1192A, Type 32 and Manufacturers Standardization Society

ANSI/MSS SP-69 & SP-58, Type 31.

Finish: Plain or Electro-Galvanized.

Contact customer service for

alternative finishes and materials.

Order By: Part number, hole size ‘H’, and finish

A B C Design Load * Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B3065-1 13\" (330.2) 9\" (228.6) 111

/2\" (292.1) 275 (1.22) 571 (259.0)

B3065-2 17\" (431.8) 13\" (330.2) 151

/2\" (393.7) 275 (1.22) 769 (348.8)

B3065-3 23\" (584.2) 19\" (482.6) 211

/2\" (546.1) 275 (1.22) 1057 (479.4)

B

1

1

/2\"

(38.1)

H Dia.

Specify

C

A

A

9

/16\" Dia.

(14.3)

2 Holes

9

/16\" Dia.

(14.3)

2 Holes

A B C H Dia. Design Load * Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B3068-1 9\" (228.6) 8\" (203.2) 61

/2\" (165.1) Specify (Specify) 275 (1.22) 360 (163.3)

B3068-2 13\" (330.2) 12\" (304.8) 101

/2\" (266.7) Specify (Specify) 275 (1.22) 582 (264.0)

B3068-3 19\" (482.6) 18\" (457.2) 161

/2\" (419.1) Specify (Specify) 275 (1.22) 860 (390.1)

* Design load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

* Design load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

Brackets

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

86 Eaton B-Line series Fire Protection Solutions

Brackets

B3064 - Adjustable strut bracket

Material: Steel

Function: Designed for supporting pipe from walls or

structures where lateral adjustment is required.

Standard Finish: Plain or Electro-Galvanized

Order By: Part number and finish.

A B Design Load * Approx. Wt./100

Part No. in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B3064-1 15\" (381.0) 12\" (304.8) 590 (2.62) 660 (299.4)

B3064-2 21\" (533.4) 18\" (457.2) 310 (1.38) 1004 (455.4)

B3064-3 27\" (685.8) 24\" (609.6) 170 (0.75) 1346 (610.5)

9

/16\" Dia. (14.3)

2 Holes

3

/8\"

(9.5)

2\"

(50.8)

B22 Channel

B32 Channel

B

1

1

/4\"

(31.7)

1

1

/4\"

(31.7)

1

5

/8\"

(41.2)

45°

A

B3066 - Welded bracket - medium duty

Max. Recommended Load: 800 lbs. (3.56kN)

Material: Steel

Function: Recommended for supporting pipe on

top or hanging through support bracket outward

from mounting surface.

Approvals: Conforms to Federal Specification

WW-H-171E & A-A-1192A, Type 33 and

Manufacturers Standardization Society

ANSI/MSS SP-69 & SP-58, Type 32.

Finish: Plain. Contact customer service for

alternative finishes and materials.

Order By: Figure number and finish

B

C

A

1\"

(25.4)

13/16\" Dia.

(20.6)

2 Holes

A B C Design Load * Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B3066-0 18\" (457.2) 12\" (304.8) 151

/2\" (393.7) 800 (3.56) 1577 (715.3)

B3066-1 24\" (609.6) 18\" (457.2) 211

/2\" (546.1) 800 (3.56) 2578 (1169.4)

B3066-2 30\" (762.0) 24\" (609.6) 271

/2\" (698.5) 800 (3.56) 4446 (2016.7)

* Design load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

* Design load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

Brackets

Brackets

87 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

B3067 - Welded bracket - heavy duty

Mtg. Hole H A B C D

Part No. in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3067-0 11

/8\" (28.6) 18\" (457.2) 12\" (304.8) 151

/4\" (387.3) ** **

B3067-1 11

/8\" (28.6) 24\" (609.6) 18\" (457.2) 211

/4\" (539.7) 21

/2\" (63.5)

B3067-2 11

/8\" (28.6) 30\" (762.0) 24\" (609.6) 271

/4\" (692.1) 21

/2\" (63.5)

B3067-3 11

/8\" (28.6) 36\" (914.4) 30\" (762.0) 33\" (838.2) 21

/2\" (63.5)

B3067-4 11

/8\" (28.6) 42\" (1066.8) 36\" (914.4) 39\" (990.6) 31

/2\" (88.9)

B3067-5 11

/8\" (28.6) 50\" (1270.0) 42\" (1066.8) 46\" (1168.4) 31

/2\" (88.9)

Design Load * Approx. Wt./100

Part No. Lbs. (kN) Lbs. (kg)

B3067-0 1850 (8.23) 2195 (995.6)

B3067-1 1850 (8.23) 4398 (1994.9)

B3067-2 1850 (8.23) 6294 (2854.9)

B3067-3 1850 (8.23) 7196 (3264.1)

B3067-4 1850 (8.23) 13197 (5986.2)

B3067-5 1850 (8.23) 15795 (7164.6)

B

H

3 Holes

Only one hole in top for B3067-0

C

A

D

Max. Recommended Load: 3000 lbs. (13.34kN)

Material: Steel

Function: Recommended for supporting pipe on top or

hanging through support bracket outward from mounting

surface.

Approvals: Conforms to Federal Specification WW-H-171E

& A-A-1192A, Type 33 and Manufacturers Standardization

Society ANSI/MSS SP-69 & SP-58, Type 33.

Finish: Plain or Electro-Galvanized. Contact customer

service for alternative finishes and materials.

Order By: Part number and finish

** One Hole

1\"

(25.4)

B3067-0

Shown

* Design load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

Brackets

Brackets

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

88 Eaton B-Line series Fire Protection Solutions

B3069W - Welded knee bracket

Size Range: 1

/2\" (15mm) thru 8\" (200mm) pipe

Material: Steel

Function: Recommended for suspending pipe outward from mounting surface.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative finishes

and materials.

Note: Maximum “L” dimension 16\" (406.4mm).

Order By: Figure number, pipe size, (**) “L” dimension and finish

Pipe Size Hole Size H Max. Rec. Load ***

Part No. in. (mm) in. (mm) Lbs. (kN)

B3069W-1

/2-** 1

/2\" (15) 9

/16\" (14.3) 450 (2.00)

B3069W-3

/4-** 3

/4\" (20) 9

/16\" (14.3) 450 (2.00)

B3069W-1-** 1\" (25) 9

/16\" (14.3) 450 (2.00)

B3069W-11

/4-** 11

/4\" (32) 9

/16\" (14.3) 450 (2.00)

B3069W-11

/2-** 11

/2\" (40) 9

/16\" (14.3) 450 (2.00)

B3069W-2-** 2\" (50) 9

/16\" (14.3) 450 (2.00)

B3069W-21

/2-** 21

/2\" (65) 9

/16\" (14.3) 450 (2.00)

B3069W-3-** 3\" (80) 9

/16\" (14.3) 450 (2.00)

B3069W-31

/2-** 31

/2\" (90) 9

/16\" (14.3) 450 (2.00)

B3069W-4-** 4\" (100) 11/16\" (17.5) 450 (2.00)

B3069W-5-** 5\" (125) 11/16\" (17.5) 450 (2.00)

B3069W-6-** 6\" (150) 11/16\" (17.5) 450 (2.00)

B3069W-8-** 8\" (200) 11/16\" (17.5) 450 (2.00)

H

L

B3069E - “O” Bracket

Size Range: 1

/2\" (15mm) thru 8\" (200mm) pipe

Material: Carbon Steel

Function: Recommended for suspending pipe outward from mounting surface.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Note: Maximum “L“ dimension 16\" (406.4mm).

Order By: Figure number, pipe size, (**) “L” dimension and finish

Pipe Size Hole Size H Max. Rec. Load ***

Part No. in. (mm) in. (mm) Lbs. (kN)

B3069E-1

/2-** 1

/2\" (15) 9

/16\" (14.3) 65 (0.29)

B3069E-3

/4-** 3

/4\" (20) 9

/16\" (14.3) 65 (0.29)

B3069E-1-** 1\" (25) 9

/16\" (14.3) 65 (0.29)

B3069E-11

/4-** 11

/4\" (32) 9

/16\" (14.3) 65 (0.29)

B3069E-11

/2-** 11

/2\" (40) 9

/16\" (14.3) 65 (0.29)

B3069E-2-** 2\" (50) 9

/16\" (14.3) 65 (0.29)

B3069E-21

/2-** 21

/2\" (65) 9

/16\" (14.3) 65 (0.29)

B3069E-3-** 3\" (80) 9

/16\" (14.3) 65 (0.29)

B3069E-31

/2-** 31

/2\" (90) 9

/16\" (14.3) 65 (0.29)

B3069E-4-** 4\" (100) 11/16\" (17.5) 65 (0.29)

B3069E-5-** 5\" (125) 11/16\" (17.5) 65 (0.29)

B3069E-6-** 6\" (150) 11/16\" (17.5) 65 (0.29)

B3069E-8-** 8\" (200) 11/16\" (17.5) 65 (0.29)

H

L

** Length to be specified as shown on the drawing.

** Length to be specified as shown on the drawing.

*** Load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

*** Load based on a safety factor of 5 and reduced by 250 lbs per NFPA.

Upper Attachments

89 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Upper Attachments

Part No. Pipe Size A B C Hole Dia. D Thread Size Approx. Wt./100

in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) E Lbs. (kg)

78-3

/8 1

/2\" - 2\" (15 - 60) 3\" (76.2) 21

/8\" (54.0) 11

/8\" (28.6) 5

/16\" (7.9) 3

/8\"-16 15 (6.8)

Size Range: 3

/8\"-16 rod

Material: Pre-Galvanized Steel

Function: Attachment to wood beams, ceilings, metal decks

or walls. Can also be welded to steel beams.

Approvals: Underwriters Laboratories Listed in the USA (UL)

and Canada (cUL). Additionally, UL has listed the Fig. 78 with

fasteners as shown in the table below.

Finish: Plain or Electro-Galvanized. Contact customer service

for alternative finishes and materials.

Order By: Figure number, rod size and finish

Patent #5,702,077

UL Listed Fastener Table

Pipe Size Qty Fastener Type Material

1

/2\" - 2\" 2 #14 x 11

/4\" A-point hex-washer-head sheet metal screw Wood

21

/2\" - 4\" 2 1

/4\" x 11

/2\" wood screws* Wood

1

/2\" - 2\" 2 1

/4\" x 1\" tek screws Metal (18 gauge)

1

/2\" - 2\" 2 #14 x 11

/4\" A-point hex-washer-head sheet metal screw Wood

1

/2\" - 2\" 2 #14 x 2\" A-point-hex-washer-head sheet metal screw Wood thru 5

/8\" gyp board

* No pre-drilling

TOLCO Fig. 78 - all steel ceiling plate

A B

C

D

(2 Holes)

E

TOLCO Fig. 51 - side beam bracket for NFPA rod & fastener sizing

Size Range: 3

/8\"-16 thru 1

/2\"-13 rod, 1

/2\" (15mm) thru 8\" pipe (200mm)

Material: Steel

Function: Recommended for attaching hanger rod to side of beams or walls.

Designed to accommodate current rod schedule and fastener requirements per

National Fire Protection Association (NFPA) Pamphlet 13.

Approvals: Underwriters Laboratories Listed in the USA (UL) and

Canada (cUL), and Factory Mutual Engineering approved.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number and finish

Part No. Pipe Size Rod A B C Hole 1 Hole 2 Approx. Wt./100

in. (mm) Size in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

51NFPA-3

/8x3

/8 1

/2\" - 2\" (15 - 60) 3

/8\"-16 2\" (50.8) 3

/4\" (19.0) 2\" (50.8) 7

/16\" (11.1) 7

/16\" (11.1) 35 (15.9)

51NFPA-3

/8x1

/2 21

/2\" - 4\" (65 - 100) 3

/8\"-16 2\" (50.8) 3

/4\" (19.0) 2\" (50.8) 9

/16\" (14.3) 7

/16\" (11.1) 34 (15.4)

51NFPA-1

/2x1

/2 5\" - 6\" (125 - 150) 1

/2\"-13 21

/2\" (63.5) 3

/4\" (19.0) 21

/2\" (63.5) 9

/16\" (14.3) 9

/16\" (14.3) 71 (32.2)

51NFPA-1

/2x5

/8 8\" (200) 1

/2\"-13 21

/2\" (63.5) 3

/4\" (19.0) 21

/2\" (63.5) 11/16\" (17.5) 9

/16\" (14.3) 70 (31.7)

Hole 1

Hole 2

B

B

C

A

A

Larger pipe sizes can be hung with reduced spacing.

Upper Attachments

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

90 Eaton B-Line series Fire Protection Solutions

Upper Attachments

Size Range: 3

/8\"-16 thru 7

/8\"-9 rod

Material: Steel

Function: Recommended for attaching hanger rod to side of beams or walls.

Approvals: 3

/8\"-16 - Underwriters Laboratories Listed in the USA (UL) and

Canada (cUL), and Factory Mutual Engineering (FM) approved.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, rod size and finish

Size Range: 1

/2\" (15mm) thru 4\" (100mm) pipe (3

/8\"-16 rod)

Material: Stainless Steel Type 304 or 316

Function: Recommended for attaching hanger rod to steel or wood

beams. Tapped hole allows easy adjustment of hanger rod.

Approvals: Underwriters Laboratories Listed in the USA (UL) and

Canada (cUL), and Factory Mutual Engineering (FM) approved for 1

/2\"

(15mm) thru 4\" (100mm) pipe.

Order By: Figure number

Note: Available only in Stainless Steel materials.

Per NFPA 13: 1

/2\" (15mm) thru 2\" (50mm) pipe use 3

/8\"-16 fastener;

21

/2\" (65mm) thru 4\" (100mm) pipe, use 1

/2\"-13 fastener.

TOLCO Fig. 50 - side beam bracket

C

A

A

B

H

H

B

3

/8\"-16

2

5

/8\"

(66.7)

1\"

(25.4)

1

1

/4\"

(31.7)

7

/16\"

(11.1)

9

/16\"

(14.3)

Part No. Rod A B C Hole Size H Approx. Wt./100

Size in. (mm) in. (mm) in. (mm) in. (mm) Lbs. (kg)

50-3

/8 3

/8\"-16 2\" (50.8) 3

/4\" (19.0) 2\" (50.8) 7

/16\" (11.1) 35 (15.9)

50-1

/2 1

/2\"-13 2\" (50.8) 3

/4\" (19.0) 2\" (50.8) 9

/16\" (14.3) 35 (15.9)

50-5

/8 5

/8\"-11 2\" (50.8) 3

/4\" (19.0) 2\" (50.8) 11/16\" (17.5) 32 (14.5)

50-3

/4 3

/4\"-10 21

/2\" (63.5) 3

/4\" (19.0) 21

/2\" (63.5) 13/16\" (20.6) 110 (49.9)

50-7

/8 7

/8\"-9 21

/2\" (63.5) 3

/4\" (19.0) 21

/2\" (63.5) 15/16\" (23.8) 100 (45.3)

Material: Steel

Function: — Recommended for supporting pipe at various distances

from wall or column.

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number and finish

B3061 - Angle bracket

A

B

Part No. Size A B Hole Size Max. Rec. Load Approx. Wt./100

in. (mm) Size in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B3061-1 1 3\" (76.2) 2\" (50.8) 7

/16\" (11.1) 180 (0.80) 46 (20.8)

B3061-2 2 4\" (101.6) 3\" (76.1) 7

/16\" (11.1) 180 (0.80) 65 (29.5)

B3061-3 3 3\" (76.2) 2\" (50.8) 9

/16\" (14.3) 390 (1.73) 85 (38.5)

B3061-4 4 4\" (101.6) 3\" (76.1) 9

/16\" (14.3) 390 (1.73) 115 (52.1)

Part No. Approx. Wt./100

Lbs. (kg)

56 20 (9.1)

TOLCO Fig. 56 - tapped side beam connector (stainless steel)

Upper Attachments

Upper Attachments

91 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

Size Range: 3

/8\"-16 rod, pipe sizes 1

/2\" (15mm) thru 4\" (100mm)

Material: Pre-Galvanized Steel

Function: Practical and economical bracket used to support piping from wood, concrete

or steel beams.

Features: Unique design allows rod to be easily threaded into bracket. Offset design

permits unlimited rod adjustment. Center mounting hole will accept 3

/8\" and 1

/2\" fastener

bolts. Per NFPA 13: 1

/2\" (15mm) thru 2\" (50mm) pipe requires 3

/8\" fastener, 21

/2\" (65mm)

thru 4\" (100mm) pipe requires 1

/2\" fastener.*

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL), and

Factory Mutual Engineering approved thru 4\" (100mm) pipe.

Finish: Pre-Galvanized

Order By: Figure number and finish

*Note: Additionally UL has listed the Fig. 58 with fasteners as shown in table below.

TOLCO Fig. 58 - threaded side beam bracket

A

C

2 - 1

/4\" x 2\" Lag Bolts

(No Pre-Drilling

Up to 4\" (100mm) pipe

Per NFPA

1 - 3

/8\" or 1

/2\" Lag Bolts

Up to 4\" (100mm) pipe

2 - #16 x 2\"

Drive Screws 1

/2\" (15mm) - 4\" (100mm) pipe

Bolt & Hex Nut

Up to 4\" (100mm) pipe

2 - #14 x 1\"

Tek Type Screws

Into Min. 16 Gauge Steel

Up to 4\" (100mm) pipe

B

UL Listed Fastener Table

Pipe Size Qty Fastener Type Material

2\" 2 #16 x 2\" Drive screws Wood

2\" 1 3

/8\" Lag bolt Wood

21

/2\" - 4\" 1 1

/2\" Lag bolt Wood

31

/2\" 2 1

/4\" x 11

/2\" Lag bolts Wood

4\" 2 1

/4\" x 2\" Lag bolts ** Wood

4\" 2 1

/4\" x 1\" Tek screws Metal (15 gauge)

4\" 2 1

/4\" x 1\" Tek screws Metal (16 gauge)

** No pre-drilling

Part No. Pipe Size Rod A B C Approx. Wt./100

in. (mm) Size in. (mm) in. (mm) in. (mm) Lbs. (kg)

58 1

/2\" - 4\" (15 - 100) 3

/8\"-16 23

/4\" (69.8) 11

/2\" (38.1) 11

/8\" (28.6) 14 (6.3

Larger pipe sizes can be hung with reduced spacing.

Threaded Accessories

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

92 Eaton B-Line series Fire Protection Solutions

B3200 - Weldless Eye Nut

Size Range: 3

/8\"-16 thru 21

/2\"-41

/2 machine thread.

Material: Forged Steel

Quality Assurance: Conforms to the requirements of NCA 3800.

Threads: Tapped UNC Class 2B. Right hand threads are standard. Left

hand threads supplied upon request (B3200L).

Function: Used on piping installations where high strength and swivel

action are required. Left hand tap is also available.

Approvals: Approvals: Included in our Seismic Engineering Guidelines

approved by the State of California Office of Statewide Health Planning

and Development (OSHPD). For additional load, spacing and placement

information relating to OSHPD projects, please refer to our Seismic

Engineering Guidelines, OPM-0052-13.

Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 17 and

Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 17.

Finish: Plain. Contact customer service for alternative finishes and

materials.

Order By: Figure number and finish.

A

(Rod Size)

Hanger Rod Not

Included

E

F

B

C

F

A

D

Rod Size B C D E F G

Part No. A in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm)

B3200-3

/8 3

/8\"-16 11

/2\" (38.1) 13

/16\" (30.2) 1

/2\" (12.7) 2\" (50.8) 13

/8\" (34.9) 11/16\" (17.5)

B3200-1

/2 1

/2\"-13 11

/2\" (38.1) 13

/16\" (30.2) 1

/2\" (12.7) 2\" (50.8) 13

/8\" (34.9) 11/16\" (17.5)

B3200-5

/8 5

/8\"-11 11

/2\" (38.1) 13

/16\" (30.2) 1

/2\" (12.7) 2\" (50.8) 13

/8\" (34.9) 11/16\" (17.5)

B3200-3

/4 3

/4\"-10 11

/2\" (38.1) 13

/16\" (30.2) 1

/2\" (12.7) 2\" (50.8) 13

/8\" (34.9) 11/16\" (17.5)

B3200-7

/8 7

/8\"-9 2\" (50.8) 111/16\" (42.9) 3

/4\" (19.0) 25

/8\" (66.7) 115/16\" (49.2) 1\" (25.4)

Design Load

650°F (343°C) 750°F (399°C) Approx. Wt./100

Part No. Lbs. (kN) Lbs. (kN) Lbs. (kg)

B3200-3

/8 610 (2.71) 540 (2.40) 63 (28.6)

B3200-1

/2 1130 (5.02) 1010 (4.49) 60 (27.2)

B3200-5

/8 1810 (8.05) 1610 (7.16) 59 (26.7)

B3200-3

/4 2710 (12.05) 2420 (10.76) 56 (25.4)

B3200-7

/8 3770 (16.77) 3360 (14.94) 170 (77.1)

For larger sizes consult full line pipe hanger catalog.

OPM

Threaded Accessories

Threaded Accessories

93 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

B501 - Light weight u-bolt with 2 hex nuts

A

B

D

C

Hex Nuts

Included

Design Load

Size Range: Size 1

/2\" (15mm) thru 8\" (200mm) pipe

Material: Carbon Steel

Function: Recommended for supporting or anchoring light pipe loads.

Maximum Temperature: 650°F (343°C)

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number and finish.

Note: When furnished in Hot-Dip Galvanized finish, oversize

tapped hex nuts must be used.

A B C D Design Load Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B501-1

/2 15/16\" (23.8) 13

/4\" (44.4) 11

/2\" (38.1) 5

/16\"-18 600 (2.67) 12 (5.4)

B501-3

/4 11

/8\" (28.6) 13

/4\" (44.4) 15

/8\" (41.3) 5

/16\"-18 600 (2.67) 13 (5.9)

B501-1 13

/8\" (29.9) 17

/8\" (47.6) 15

/8\" (41.3) 5

/16\"-18 900 (4.00) 14 (6.3)

B501-11

/4 123/32\" (43.6) 13

/4\" (44.4) 115/32\" (37.3) 5

/16\"-18 900 (4.00) 15 (6.8)

B501-11

/2 2\" (50.8) 13

/4\" (44.4) 17

/16\" (36.5) 5

/16\"-18 900 (4.00) 16 (7.2)

B501-2 27

/16\" (61.9) 21

/16\" (52.4) 17

/8\" (47.6) 3

/8\"-16 1200 (5.34) 27 (12.2)

B501-21

/2 215/16\" (74.6) 21

/16\" (52.4) 113/16\" (46.0) 3

/8\"-16 1200 (5.34) 32 (14.5)

B501-3 39

/16\" (90.5) 2\" (50.8) 13

/4\" (44.4) 3

/8\"-16 1800 (8.00) 36 (16.3)

B501-31

/2 43

/32\" (94.6) 2\" (50.8) 123/32\" (43.6) 3

/8\"-16 1800 (8.00) 38 (17.2)

B501-4 419/32\" (116.7) 21

/4\" (57.1) 121/32\" (50.0) 3

/8\"-16 1800 (8.00) 42 (19.0)

B501-5 521/32\" (143.6) 21

/4\" (57.1) 2\" (50.8) 1

/2\"-13 2400 (10.70) 92 (41.7)

B501-6 63

/4\" (171.4) 25

/8\" (66.7) 23

/8\" (60.3) 5

/8\"-11 2400 (10.70) 176 (79.8)

B501-8 83

/4\" (222.2) 25

/8\" (66.7) 23

/8\" (60.3) 5

/8\"-11 2400 (10.70) 191 (86.6)

B

Thread Length

Threaded Accessories

Threaded Accessories

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

94 Eaton B-Line series Fire Protection Solutions

Threaded Accessories

B3188 - Standard U-bolt with 4 hex nuts

B3188C - Standard plastic coated U-bolt

Size Range: Size 1

/2\" (15mm) thru 30\" (900mm) pipe

Material: Steel

Function: Recommended for support, anchor or guide of pipe.

Approvals: Underwriters Laboratories Listed 3

/4\" (20mm) thru 12\"

(300mm). Conforms to Federal Specification WW-H-171E & A-A-1192A,

Type 24 and Manufacturers Standardization Society ANSI/MSS SP-69 &

SP-58, Type 24.

Maximum Temperature: 750°F (399°C)

Finish: Plain or Electro-Galvanized. Contact customer service for

alternative finishes and materials.

Order By: Figure number and finish. U-bolt can be furnished with longer

tangents “D” or with longer threads “E”. Consult factory.

Note: When furnished in Hot-Dip Galvanized finish, oversize tapped hex

nuts must be used. B3188NS - Non-standard (NS) U-bolts are available

upon request. Specify dimensions other than standard. B3188DI - For

ductile iron pipe.

TL

Thread Length

A

Thread Size

B

E

TL

Design

Load 2

Design

Load 3

Design

Load 1

D

C

Hex Nuts Included

Pipe Size Thread Size Thread Length TL B

Part No. in. (mm) in. (mm) in. (mm)

B3188-1

/2 1

/2\" (15) 1

/4\"-20 21

/8\" (54.0) 15/16\" (23.8)

B3188-3

/4 3

/4\" (20) 1

/4\"-20 21

/8\" (54.0) 11

/8\" (28.6)

B3188-1 1\" (25) 1

/4\"-20 21

/8\" (54.0) 13

/8\" (34.9)

B3188-11

/4 11

/4\" (32) 3

/8\"-16 21

/8\" (54.0) 111/16\" (42.9)

B3188-11

/2 11

/2\" (40) 3

/8\"-16 21

/2\" (63.5) 2\" (50.8)

B3188-2 2\" (50) 3

/8\"-16 21

/2\" (63.5) 27

/16\" (61.9)

B3188-21

/2 21

/2\" (65) 1

/2\"-13 3\" (76.2) 215/16\" (74.6)

B3188-3 3\" (80) 1

/2\"-13 3\" (76.2) 39

/16\" (90.5)

B3188-31

/2 31

/2\" (90) 1

/2\"-13 3\" (76.2) 41

/16\" (103.2)

B3188-4 4\" (100) 1

/2\"-13 3\" (76.2) 49

/16\" (115.9)

B3188-5 5\" (125) 1

/2\"-13 3\" (76.2) 521/32\" (143.6)

B3188-6 6\" (150) 5

/8\"-11 33

/4\" (95.2) 63

/4\" (171.4)

B3188-8 8\" (200) 5

/8\"-11 33

/4\" (95.2) 83

/4 “ (222.2)

B3188-10 10\" (250) 3

/4\"-10 4\" (101.6) 107

/8\" (276.2)

B3188-12 12\" (300) 7

/8\"-9 41

/4\" (107.9) 127

/8\" (327.0)

B3188-14 14\" (350) 7

/8\"-9 41

/4\" (107.9) 141

/8\" (358.8)

B3188C

Plastic Coated

For larger sizes consult full line pipe hanger catalog.

Threaded Accessories

Threaded Accessories

95 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

C Tangent D E Approx. Wt./100

Part No. in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3188-1

/2 13

/16\" (30.2) 23

/4\" (69.8) 25

/16\" (58.7) 10 (4.5)

B3188-3

/4 13

/8\" (34.9) 23

/4\" (69.8) 27

/32\" (56.3) 11 (5.0)

B3188-1 15

/8\" (41.3) 23

/4\" (69.8) 23

/32\" (53.2) 11 (5.0)

B3188-11

/4 23

/32\" (53.2) 27

/8\" (73.0) 21

/32\" (51.6) 28 (12.7)

B3188-11

/2 23

/8\" (60.3) 3\" (76.2) 21

/16\" (52.4) 29 (13.1)

B3188-2 213/16\" (71.4) 31

/4\" (82.5) 21

/16\" (52.4) 31 (14.0)

B3188-21

/2 37

/16\" (87.3) 33

/4\" (95.2) 25

/16\" (58.7) 72 (32.6)

B3188-3 41

/16\" (103.2) 4\" (101.6) 21

/4\" (57.1) 79 (35.8)

B3188-31

/2 49

/16\" (115.9) 41

/4\" (107.9) 21

/4\" (57.1) 84 (38.1)

B3188-4 51

/16\" (128.6) 41

/2\" (114.3) 21

/4\" (57.1) 94 (42.6)

B3188-5 65

/32\" (156.3) 5\" (127.0) 27

/32\" (56.3) 104 (47.2)

B3188-6 73

/8\" (187.3) 61

/8\" (155.6) 213/16\" (71.4) 203 (92.1)

B3188-8 93

/8\" (238.1) 71

/8\" (181.0) 213/16\" (71.4) 241 (109.3)

B3188-10 115

/8\" (295.3) 83

/8\" (212.7) 31

/4\" (82.5) 412 (186.9)

B3188-12 133

/4\" (349.2) 95

/8\" (244.5) 31

/4\" (82.5) 661 (299.8)

B3188-14 15\" (381.0) 101

/4\" (260.3) 3\" (76.2) 707 (320.7)

Design Load 1 Design Load 2 Design Load 3

650°F (343°C) 750°F (399°C) 650°F (343°C) 650°F (343°C)

Part No. Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

B3188-1

/2 580 (2.58) 454 (2.02) 145 (0.64) 180 (0.80)

B3188-3

/4 580 (2.58) 454 (2.02) 145 (0.64) 300 (1.33)

B3188-1 580 (2.58) 454 (2.02) 145 (0.64) 480 (2.13)

B3188-11

/4 1460 (6.49) 1144 (5.09) 365 (1.62) 600 (2.67)

B3188-11

/2 1460 (6.49) 1144 (5.09) 365 (1.62) 600 (2.67)

B3188-2 1460 (6.49) 1144 (5.09) 365 (1.62) 720 (3.20)

B3188-21

/2 2700 (12.01) 2114 (9.40) 675 (3.00) 720 (3.20)

B3188-3 2700 (12.01) 2114 (9.40) 675 (3.00) 900 (4.00)

B3188-31

/2 2700 (12.01) 2114 (9.40) 675 (3.00) 900 (4.00)

B3188-4 2700 (12.01) 2114 (9.40) 675 (3.00) 900 (4.00)

B3188-5 2700 (12.01) 2114 (9.40) 675 (3.00) 1080 (4.80)

B3188-6 4320 (19.21) 3382 (15.04) 1080 (4.80) 1080 (4.80)

B3188-8 4320 (19.21) 3382 (15.04) 1080 (4.80) — —

B3188-10 6460 (28.73) 5060 (22.50) 1615 (7.18) — —

B3188-12 9960 (44.30) 7016 (31.21) 2490 (11.07) — —

B3188-14 9960 (44.30) 7016 (31.21) 2490 (11.07) — —

B3188 - Standard U-Bolt with 4 Hex Nuts cont’d.

For larger sizes consult full line pipe hanger catalog.

Threaded Accessories

Threaded Accessories

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

96 Eaton B-Line series Fire Protection Solutions

B3205 - Threaded rod (right-hand threads - both ends)

B3205L - Threaded rod (right & left hand threads)

ATR - All threaded rod - 120\" (3.05m) lengths

TOLCO Fig. 99 - all threaded rod cut to length

Size Range: 3

/8\"-16 thru 7

/8\"-9 rod

Material: Steel

Function: Recommended for use as a hanger support in hanger assemblies.

Rod is threaded on both ends with right hand threads of the length shown. Also

available with left and right hand threads - specify Fig. B3205L when ordering.

Maximum Temperature: 750°F (399°C)

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, rod size, length and finish

Size Range: 1

/4\"-20 thru 7

/8\"-9 rod in 120\" lengths or cut to length

Material: Steel

Maximum Temperature: 750°F (399°C)

Finish: Plain or Electro-Galvanized. Contact customer service for alternative finishes

and materials.

Approvals: Included in our Seismic Engineering Guidelines approved by the State

of California Office of Statewide Health Planning and Development (OSHPD). For

additional load, spacing and placement information relating to OSHPD projects,

please refer to our Seismic Engineering Guidelines, OPM-0052-13.

Order By: Figure number, rod size, length and finish

A

Thread Size

TL

TL

Specify Length

‘L’

Standard Design Load

Thread Size Thread Length TL 650°F (343°C) 750°F (399°C)

Part No. A in. (mm) Lbs. (kN) Lbs. (kN)

B3205-3

/8 x ‘L’ 3

/8\"-16 21

/2\" (63.5) 730 (3.25) 572 (2.54)

B3205-1

/2 x ‘L’ 1

/2\"-13 21

/2\" (63.5) 1350 (6.00) 1057 (4.70)

B3205-5

/8 x ‘L’ 5

/8\"-11 21

/2\" (63.5) 2160 (9.61) 1692 (7.52)

B3205-3

/4 x ‘L’ 3

/4\"-10 3\" (76.2) 3230 (14.37) 2530 (11.25)

B3205-7

/8 x ‘L’ 7

/8\"-9 31

/2\" (88.9) 4480 (19.93) 3508 (15.60)

Part No. - Size x Length Threads Recommended Load Approx. Wt./100 Ft.

ATR Fig. 99 Per Inch Lbs. (kN) Lbs. (kg)

ATR 1

/4\" x 120 99-1

/4\" x length 20 240 (1.07) 12 (5.44)

ATR 3

/8\" x 120 99-3

/8\" x length 16 730 (3.24) 29 (13.15)

ATR 1

/2\" x 120 99-1

/2\" x length 13 1350 (6.00) 53 (24.04)

ATR 5

/8\" x 120 99-5

/8\" x length 11 2160 (9.60) 89 (40.37)

ATR 3

/4\" x 120 99-3

/4\" x length 10 3230 (14.37) 123 (55.79)

ATR 7

/8\" x 120 99-7

/8\" x length 9 4480 (19.93) 170 (77.11)

For larger sizes consult full line pipe hanger catalog.

For larger sizes consult full line pipe hanger catalog.

OPM

Threaded Accessories

Threaded Accessories

97 Eaton

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

B-Line series Fire Protection Solutions

B3214 - Tie bolt

Material: Steel

Function: Recommended for securing the connection of steel pipe to

ductile pipe first attach tie bolts to pipe flanges then connect tie rods. May

be used in vertical or horizontal applications.

Approvals: As shown in NFPA Pamphlet 24, Installation of Private Fire

Service Maintenance 4\" (100mm) - 12\" (300mm) pipe size.

Finish: Plain. Contact customer service for alternative finishes and materials.

Order By: Figure number, length and finish.

Custom lengths for thicker flange available.

Size Range: 3

/8\"-16 rod thru 1

/2\"-13 rod

Material: Steel

Function: Typically used to suspend pipe from wood joists.

Machine threaded on one end and lag threaded on the other

end. It is recommended that pilot holes be pre-drilled to prevent

beam from splitting and to aid in starting lag threads.

Approvals: Conforms to the requirements of NFPA13.

Finish: Plain. Contact customer service for alternative

finishes and materials.

Order By: Figure number, rod size, length and finish

B3213 - Coach screw rod

*3

/8 x 31

/2 and 1

/2 x 31

/2 will have a coach screw thread length of 2\" (50.8) and a rod thread length of 1\" (25.4).

Design Load is based on proper installation and solid wood.

A

Thread Size

B

C

Specify L

Size Specify

4\" (101.4mm) or 41

/2\"

(114.3mm)

Steel Pipe Riser

Adapter

Ground Level

All Threaded Rod

Ductile Iron Riser

Typical Application

Under Ground Pipe

1\" (25.4mm)

Max.

3

/4\" (19.0mm)

Dia.

Thread Coach Screw Rod Thread Design

Size Standard Rod Lengths L Thread Length B Length C Load

Part No. A in. (mm) in. (mm) in. (mm) Lbs. (kg)

B3213-3

/8 x ‘L’ 3

/8\"-16 *31

/2\", 8\" (88.9, 203.2) 2\" (50.8) 2\" (50.8) 390 (1.73)

B3213-1

/2 x ‘L’ 1

/2\"-13 *31

/2\", 8\" (88.9, 203.2) 21

/2\" (63.5) 21

/2\" (63.5) 640 (2.84)

Length Approx. Wt./100

Part No. in. (mm) Lbs. (kg)

B3214-4 4\" (101.6) 107.5 (48.5)

B3214-41

/2 41

/2\" (114.3) 113.7 (51.6)

Threaded Accessories

Threaded Accessories

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

98 Eaton B-Line series Fire Protection Solutions

Size Range: 3

/8\"-16 thru 7

/8\"-19 rod

Material: Steel

Function: Designed to be hooked or hung from beam flange or purlin.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative

finishes and materials.

Order By: Figure number, length and finish

B3212 - J-bolt

A

Thread Size

TL

Thread Length

Radius D

Specify Length L

Thread Size Thread Length TL Radius D Design Load

Part No. A in. (mm) in. (mm) Lbs. (kg)

B3212-3

/8 x ‘L’ 3

/8\"-16 2\" (50.8) 1

/2\" (12.7) 240 (1.07)

B3212-1

/2 x ‘L’ 1

/2\"-13 2\" (50.8) 5

/8\" (15.9) 440 (1.96)

B3212-5

/8 x ‘L’ 5

/8\"-11 21

/2\" (63.5) 3

/4\" (19.0) 705 (3.13)

B3212-3

/4 x ‘L’ 3

/4\"-10 21

/2\" (63.5) 7

/8\" (22.2) 1050 (4.67)

B3212-7

/8 x ‘L’ 7

/8\"-9 21

/2\" (63.5) 1\" (25.4) 1470 (6.54)

DS 16 x 2 - Drive screw

Material: Steel

Function: Equivalent to a nail, but has greater holding power

Finish: Plain and Electro-Galvanized

Order By: Figure number and finish

B3228 - Hex head lag bolt

Material: Steel

Function: Designed to fasten metal to wood. Lag screws are made with hex heads in lengths of 6\" (152.5mm)

or shorter and square heads in lengths longer than 6\" (152.5mm). Both types have coarse lag threads and gimlet points and are available in diameters of 1

/4\"(6.3mm) to 5

/8\"(15.9mm) inclusive. Square-head lag screws are

also available in 3

/4\"(19.0mm), 7

/8\"(22.2mm) and 1\"(25.4mm) diameters.

Approvals: Qualified for static, wind, and seismic loading in concrete. Included in our Seismic Engineering

Guidelines approved by the State of California Office of Statewide Health Planning and Development (OSHPD).

For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic

Engineering Guidelines, OPM-0052-13.

Finish: Plain or Electro-Galvanized. Contact customer service for alternative finishes and materials.

Order By: Figure number, bolt size, length and finish

Bolt Diameter and Wt./C

Length 1

/4\" (6.3) 3

/8\" (9.5) 1

/2\" (12.7) 5

/8\" (15.9) 3

/4\" (19.0)

11

/2\" (38.1) 2.3 (1.0) 6.0 (2.7) 11.8 (5.3) 19.4 (8.8) 32.3 (14.6)

2\" (50.8) 2.8 (1.3) 7.0 (3.2) 14.4 (6.5) 23.2 (10.5) 38.3 (17.4)

21

/2\" (63.5) 3.3 (1.5) 8.3 (3.7) 16.2 (7.3) 27.0 (12.2) 44.0 (19.9)

3\" (76.2) 3.9 (1.7) 9.8 (4.4) 18.6 (8.4) 31.0 (14.0) 47.7 (21.6)

31

/2\" (88.9) 4.4 (2.0) 11.4 (5.2) 21.2 (9.6) 34.8 (15.8) 56.3 (25.5)

4\" (101.6) 5.0 (2.2) 12.5 (5.7) 23.3 (10.5) 37.6 (17.0) 58.5 (26.5)

41

/2\" (114.3) 5.7 (2.6) 14.0 (6.3) 26.1 (11.8) 42.6 (19.3) 64.0 (29.0)

5\" (127.0) 6.3 (2.8) 15.4 (7.0) 29.0 (13.1) 45.5 (20.6) 68.0 (30.8)

51

/2\" (139.7) 7.0 (3.2) 16.4 (7.4) 31.5 (14.3) 49.3 (22.3) 74.0 (33.5)

6\" (152.4) 7.4 (3.3) 18.3 (8.3) 34.0 (15.4) 53.0 (24.0) 77.0 (34.9)

OPM