Main technical parameter

Releasing grade of thermal relay: JRS2-12.5, 25, 32, 45, 63, 80, 135, 150, 180, 400, 630 is 10A grade Its action scope classic curve to see map 2

A. Three phase balance, unbalance, starting by cool status; B. Three phase balance, break phase, starting by thermal status

External and installation dimension

External and installation dimension of thermal to see map 3\~10

Map 3 External and installation dimension of JRS2-12.5/Z, JRS2-25/Z

Map 4 External and installation dimension of JRS2-32/Z

Map 5 External and installation dimension of JRS2-12.5/F,JRS2-25/F,JRS2-32/F

Map 6 External and installation dimension of JRS2-63

SSR/JGX

Solid State Relay

24\~380VACSSR-40 DA40A/250V4 3\~32VDC + 3人民电器集团有限公司

Main technical parameter

On-off time:Below 0.5 period of 1ms+load current
Load Voltage:25V-250VAC, H:150V-450VAC
Output Voltage Drop:1.8Vmax
Off Leakage Current:
Type zero-crossing:10mA max.(at 220VAC)15mA max.(at 380VAC)
Type random 5mA max(at 220VAC) 10mA max.(at 380VAC)
Insulation Resistance: 100M min. (at 500VDC)
Dielectric Strength: 2000VAC 50Hz/1min
Operating Temperature: -20 \~80℃

Size(mm):59×45×25

On-off time:Below 0.5 period of 1ms+load current
Load Voltage:25V-250VAC, H:150V-450VAC
Output Voltage Drop:1.8Vmax
Off Leakage Current:
Type zero-crossing:10mA max.(at 220VAC)15mA max.(at 380VAC)
Type random 5mA max(at 220VAC) 10mA max.(at 380VAC)
Insulation Resistance: 100M min. (at 500VDC)
Dielectric Strength: 2000VAC 50Hz/1min
Operating Temperature: -20 \~80℃

Size(mm)62.5×45×23.5

Off Leakage Current: 5mA No build-in RC absorption ring Insulation Resistance: 1000M 500VDC Voltage testing Dielectric Strength: 4000Vrms Input terminal output terminal 2500Vrms Input terminal, output terminal radiator Operating Temperature: -20 \~80℃

Size(mm):62.5×45×23.5

Control method:VA:Solid voltage regulator

Control Voltage:Outside-controlled adjustsble potentiometer 470K-560K/2W

Load Voltage:24V-380VAC,H:90V-480VAC Output Voltage Drop:1.5Vmax.

Off Leakage Current: 5mA No build-in RC absorption ring Insulation Resistance: 1000M 500VDC Voltage testing Dielectric Strength: 4000Vrms Input terminal output terminal 2500Vrms Input terminal, output terminal radiator Operating Temperature: -20 \~80℃

mm

JQX-10F(JTX)

Series General Purpose Relay

Dimension.Bottom View

JQX-10F(JTX)

JQX-10F 2Z

JTX-2C

JQX-10F(JTX)

JQX-10F 3Z
Reference Data

JTX-3C

HH5-P

Series General Purpose Relay

HH5 2P

HH5 3P

HH5 4P

Dimension.Bottom View

Reference Data Max.operating power
Life Expectancy

ST3P

Series Timer Relay

Application

ST3P series timer relay mainly applied as time-delay components in the control circuits with AC50/60Hz, rated voltage up to 380V or DC 24V, which makes or breaks the circuit according to the setting time, and features compact design, high accuracy and wide time-delay range. It can be interchanged with JSZ3 series relay equivalently.

Model No.

Normal operating condition and installation condition

3.1 Altitude: less than 2000m

3.2 Ambient temperature: -5℃ \~ +40℃, average temperature within 24h does not exceed +35℃.

3.3 Relative humidity: less than 50% at +40℃ , higher relative humidity can not be obtained under lower temperature.

3.4 Pollution grade: class III.

3.5 The breaker should be installed at the place without explosive risk and conductive dust, where metal not corroded and insulation not destroyed, and no rain or snow invasion

3.6 Installation category: II.

3.7 Range of source voltage: -25% \~ +55% Ue

Tab-2

Wiring diagram

ST3PA ST3PA-5P ST3PB-5P ST3P-2

ST3P-AY external potentiometer

ST3PC ST3P-3ST3PC-5PC

ST3PF

ST3P-FT1 ST3P-G ST3PF-5PF

ST3P-R ST3PR-5PR

ST3P-Y

ST3P-K

Outline and dimension

ST3P-A、ST3P-C、ST3P-G、ST3P-F、ST3P-FT1、ST3P-Y、ST3P-K

ST3P-R

ST3P-5PA、ST3P-5PB、ST3P-5PC、ST3P-5PF

ST3P-5PR

TP28X socket

KG316T/KG316TX Series Timer Switch

Application

KG316T series microprocessor timer switch mainly applied in the auto control circuits with AC50/60Hz, rated control voltage up to 220V, to switch on or off the circuits according to the scheduled time, which conforms to IEC60947-5-1 standard.

Model No.

Normal operating condition and installation condition

3.1 Altitude: less than 2000m

3.2 Ambient temperature: -5℃ \~ +40℃, average temperature within 24h does not exceed +35℃. 3.3 Relative humidity: less than 50% at +40℃, higher relative humidity can not be obtained under lower temperature.
3.4 Pollution grade: III.
3.5 Enclosure protection grade: IP20.
3.6 The timer switch should be installed at the place without explosive risk and conductive dust, where metal not corroded and insulation not destroyed, and no rain or snow invasion
3.7 Installation category: II.
3.8 Variation range of power voltage: 85% \~ 110% Ue

Main technical parameter

Rated control voltage: AC220V 50Hz Conventional thermal current: 20A Rated service current: AC-15/220V 3A Timing range: 1min \~ 168h Accuracy (Timing Error): ≤2 sec everyday Mechanical life: ≥30,000 times Electrical life: ≥10,000 times Mounting: surface or 35mm Din-rail

Wiring mode and diagram

direct control mode

controlled circuit powered by single phase source, service current less than rated value of the switch, can be directly controlled, wiring as to Fig-1.

single phase dilatation mode

controlled circuit powered by single phase source, service current more than rated value of the switch, AC contactor dilatation mode suggested, wiring as to Fig-2.

Fig-1 KG316T terminal

Fig-2 single phase direct control wiring

Three phase control wiring(as to Fig-3, 4)<br>Fig-3 three phase control wiring (220V contactor coil)

Fig-4 three phase control wiring (380V contactor coil)

Outline and dimension

KG316T

TB35 Series Timer Switch

TB353 Series Timer Switch

ALC18 Series Timer Switch

SUL180a/SUL160a Series Timer Switch

SUL181h/SUL161h Series Timer Switch

SUL181d/SUL161d Series Timer Switch

RDA2(PXB2)

Push Button Series

Compliance Standards

Application Scope

RDA2 push button switches are applicable to control circuits with AC 50/60Hz, rated working voltage of 380V or DC rated working voltage of 220V, for controlling, contactors, relays, electrom agnetic switches or converting working signals For push buttons with signal lamps, the signal lamp is inst alled at the neck of the button, and the button head also serves as the lampshade of the signal lamp, and different colors are used to distinguish signals.

Outline Drawings and Dimensions

Order Model

White Metal Flat Button,with Self-Lock, 1 NO Black Metal Flat Button,with Self-Lock, 1 NC Green Metal Flat Button,with Self-Lock, 2 NO Red Metal Flat Button,with Self-Lock, 2 NC Yellow Metal Flat Button,with Self-Lock,
1NO1NC
Blue Metal Flat Button,with Self-Lock,
1NO2NC

Meaning

White Plastic Flat Button,with Self-Lock, 1 NO Black Plastic Flat Button,with Self-Lock, 1 NC Green Plastic Flat Button,with Self-Lock, 2 NO Red Plastic Flat Button.with Self-Lock, 2 NC Yellow Plastic Flat Button,with Self-Lock,
1NO1NC
Blue Metal Flat Button,with Self-Lock,
1NO2NC

Flat button with lamp

Outline Drawings and Dimensions

RDA2-BW3585

RDA2-BW3685+102

RDA2-EW3585

RDA2-EW3685+102

Meaning

White Metal Flat Button,with Lamp
AC220 1 NO
Green Metal Flat Button,with Lamp
AC220 2 NO
Red Metal Flat Button,with Lamp
AC220 2 NC
Yellow Metal Flat Button,with Lamp
AC220 1NO1NC
Blue Metal Flat Button,with Lamp
AC220 1NO2NC

Meaning

White Plastic Flat Button with Lamp, AC220 1NO
Green Plastic Flat Button with Lamp, AC220 2NO
Red Plastic Flat Button with Lamp, AC220 2NC
Yellow Plastic Flat Button with Lamp, AC220 1NO1NC
Blue Plastic Flat Button with Lamp, AC220 1NO2NC White Metal Flat Button with Lamp and
RDA2-BW3Z181 Self-Lock, AC220 1 NO
RDA2-BW3Z383 Green Metal Flat Button with Lamp and Self-Lock, AC220 2 NO
RDA2-BW3Z484 Red Metal Flat Button with Lamp and,
RDA2-BW3Z585 Self-Lock, AC220 2 NC Yellow Metal Flat Button with Lamp and
RDA2-BW3Z685+102 Self-Lock, AC220 1NO 1NC Blue Metal Flat Button with Lamp and Self-Lock, AC220 1NO 2NC White Plastic Flat Button with Lamp and
RDA2-EW3Z181 Self-Lock, AC220 1 NO Green Plastic Flat Button with Lamp and
RDA2-EW3Z383 Self-Lock, AC220 2 NO
RDA2-EW3Z484 Red Plastic Flat Button with Lamp and,
RDA2-EW3Z585 Self-Lock, AC220 2 NC Yellow Plastic Flat Button with Lamp and
RDA2-EW3Z685+102 Self-Lock, AC220 1NO 1NC Blue Plastic Flat Button with Lamp and Self-Lock, AC220 1NO 2NC

Outline Drawings and Dimensions

Outline Drawings and Dimensions

Black Metal Knob with 2-position Locking,
RDA2-BD221 1 NO Black Metal Knob with 3-position Locking,
RDA2-BD322 1 NC
RDA2-BD433 Green Metal Knob with 2-position Reset, 2 NO
RDA2-BD544 Red Metal Knob with 3-position Reset,
RDA2-BD645 2 NC Red Metal Knob with 2-position Left Reset,
RDA2-BD735+102 1NO1NC Green Metal Knob with 3-position Right Reset, 1NO2NC Black Metal Knob with 2-position Locking,
RDA2-ED221 1 NO Black Metal Knob with 3-position Locking,
RDA2-ED322 1 NC
RDA2-ED433 Green Metal Knob with 2-position Reset, 2 NO
RDA2-ED544 Red Metal Knob with 3-position Reset, 2 NC
RDA2-ED645 Red Metal Knob with 2-position Left Reset,
RDA2-ED735+102 1NO1NC Green Metal Knob with 3-position Right Reset,1NO2NC

Outline Drawings and Dimensions

RDA2-BJ221 Metal Key Button with2- position Locking(Left-Right Pull-out),1 NO
RDA2-BJ322 Metal Key Button wit h 2- position Locking(Left
RDA2-BJ423 Pull-out),1 NC Metal Key Button wit h 3- position Locking(Left
RDA2-BJ524 Right, Middle Pull-out ),2 NO
RDA2-BJ625 Pull-out),2 NC Metal Key Button with 3- position Locking (Middle
RDA2-BJ725+102 Metal Key Button with 2- position Reset (Left Pull-out),1 NO1NC Metal Key Button with 3- position Reset (Middle Pull-out),1 NO2NC

Order Selection Meaning

RDA2-EJ221 Black Metal Long-Handle Knob with 2- position Locking,1 NO
DDA? E I32?
KDA∠-EJ3Z2 Black Metal Long-Handle Knob with 3- position
RDA2-EJ423 Locking,1 NC

Black Metal Long-Handle Knob wit h 2- position RDA2-EJ524 Reset.2 NO

RDA2-EJ625 Black Metal Long-Handle Knob wit h 3- position Reset,2 NC

RDA2-EJ725+102

Black Metal Long-Handle Knob wit h 2- position Left Reset.1 NO1NC

Black Metal Long-Handle Knob wit h 3- position Left Reset,1 NO2NC

Outline Drawings and Dimensions

Order Selection Meaning

Metal Key Button with2- position Locking(Left-
RDA2-BY211 Right Pull-out),1 NO Metal Key Button with 2- position Locking(Left
RDA2-BY222 Pull-out ),1 NC Metal Key Button with 3- position Locking(Left
RDA2-BY343 Right, Middle Pull-out ),2 NO Metal Key Button with 3- position Locking (Middle
RDA2-BY354 Pull-out ),2 NC
RDA2-BY425 Metal Key Button with 2- position Reset (Left Pull-out ),1 NO1NC
RDA2-BY525+102 Metal Key Button with 3- position Reset (Middle Pull-out ),1 NO2NC Plastic Key Button with2- position Locking
RDA2-EY211 (Left-Right Pull-out),1 NO Plastic Key Button with2- position Locking
RDA2-EY222 (Left Pull-out),1 NC Plastic Key Button with3- position Locking
RDA2-EY343 (Left Right, Middle Pull-out),2 NC Plastic Key Button with 3- position Locking
RDA2-EY354 (Middle Pull-out),2 NC Plastic Key Button with 2- position Reset
RDA2-EY425 (Left Pull-out),1 NO 1NC Plastic Key Button with 3- position Reset
RDA2-EY525+102 (Middle Pull-out),1 NO 2NC

Outline Drawings and Dimensions

Outline Drawings and Dimensions

Outline Drawings and Dimensions

Order Meaning
Selection Met al Green 60 M ushroom Head Selfreset Button , 1 NO Met al Green 60 M ushroom Head Self-
RDA2-BR31 reset Button, 1 NC
RDA2-BR32 Met al Green 60 M ushroom Head Selfreset Button, 2 NO
RDA2-BR33 Met al Red 60 M ushroom Head Selflocking Button, 1 NO
RDA2-BX41 Met al Red 60 M ushroom Head Self-
RDA2-BX42 locking Button, 1 NC Met al Red 60 M ushroom Head Self-
RDA2-BX43 locking Button, 2 NO
Order Meaning
Selection Plastic Green 60 M ushroom Head Self - reset Button , 1 NO
RDA2-ER31 Plastic Green 60 M ushroom Head Self - reset Button , 1 NC
RDA2-ER32 Plastic Green 60 M ushroom Head Self - reset Button , 2 NO
RDA2-ER33 Plastic Red 60 M ushroom Head Self-
RDA2-EX41 locking Button , 1 NO Plastic Red 60 M ushroom Head Self-
RDA2-EX42 locking Button , 1 NC Plastic Red 60 M ushroom Head Self-
RDA2-EX43 locking Button, 2 NO

Emergency Stop Button-Selection Rules

Outline Drawings and Dimensions

Metal Red 40 Emergency Stop Button
RDA2-BS51 1NO Metal Red40 Emergency Stop Button
RDA2-BS52 1NC Metal Red 40 Emergency Stop Button
RDA2-BS53 2NO
RDA2-BS54 Metal Red 40 Emergency Stop Button 2NC
RDA2-BS55 Metal Red 40 Emergency Stop Button 1NO1NC
RDA2-BS55+102 Metal Red 40 Emergency Stop Button 1NO2NC

RDA5(PXB5)

Push Button Series

Compliance with Standards

Application Scope

The RDA5 push-button switc h (hereinafter referred to as the button )is suit able for industrial control circuit swith 50/60 Hz. rated working voltage up to 400V and DC working voltage up to 230V. it is used for the control of electrom agnetic starters cont actors ,relays and other electrical circuits.

Normal Operating and Install ationl Conditions

□Ambient Air Temperature :-5\~40°C,and the average temper ature value wit hin 24 hours does not exceed 35°C

□Altitude: ≤2000m.

Air Humidity : When the maximum temperature is +40C., the relative humidity of the a ir does not exceed 50%.At lower temper atures ,a higher relative humidity is allowed For example, it reaches 90% at 20°C. Special measures should betaken for condensation occasionally generated due to temper ature changes.

□ Pollution Degree: Pollution Degree 3.

□ Installation Category: Installation Category II.

Selection Guide

Installation Dimensions

Installation Hole Dimensions and Minimum Installation Spacing Note: The thickness of the mounting plate is 1-3.5mm

Marking and Identification of Terminals

□Terminals are identified with two-digit numbers - The digit in the units placeis the function digit; - The digit in the tens place is the sequence number.

□ Function Digits Function digits 1and 2 a reused for breaking cont act elements (a Iso known as normally closed cont acts),and function digits 3 and 4 are used for making contact elements (also k nown as norm ally open contacts ).

□ Sequence Numbers Termin als belonging to the same contact element should be marked with the same sequence number

Marking of Termin als for Illumin ated Push-button Switches The two terminals of the signal lamp should be marked X1 and X2

Disassembly of Button Head and Switch Base Connecting Plate

Button Head Conneçting Plate Screwdriver

Schematic Diagram of Button Disassembly

Insert a small flathead screwdriver or similar object into the arched space of the connecting plate. Use the lever principle to press down the screwdriver and pull out the button head at the same time.

Outline Drawing and Dimensions

RDA5-AZ11 White Flat Button wit h Self- locking, 1 NO RDA5-AZ12 White Flat Button wit h Self- locking, 1 NC RDA5-AZ21 Black Flat Button wit h Self-locking, 1 NO RDA5-AZ22 Black Flat Button wit h Self-locking, 1 NC RDA5-AZ31 Green Flat Button wit h Self- locking, 1 NO RDA5-AZ33 Green Flat Button wit h Self- locking, 2 NO

Red Three- position L eft Self- reset & Right Indexing Long- Handle Knob, 1 NO

Outline Drawing and Dimensions

RDA5-D221
RDA5-D222
RDA5-D433
RDA5-D334
RDA5-D545
RDA5-D741

Meaning

Black Two-position Indexing Knob, 1NO Black Two-position Indexing Knob, 1NC Green Two-position Self-reset Knob, 2NO Green Three-position Indexing Knob, 2NC Red Three-position Self-reset Knob, 1NO1NC Red Three-position Left Self-reset & Right Indexing Knob, 1NO

Long-Handle Knob-Selection Rules

Outline Drawing and Dimensions

Black Two- position Indexing L ong- Handle Knob, 1 NO Black Two- position Indexing L ong- Handle Knob, 1 NC Black Two- position Self- reset L ong- Handle Knob, 1NO
Green Three- position Indexing L ong- Handle Knob, 1NO
Green Three- position Self- reset L ong- Handle Knob, 1NC

Outline Drawing and Dimensions

White Self- reset Illumin ated Flat
Button , 6V, 2 NO
White Self- reset Illumin ated Flat
Button , 16V, 1 NC
Yellow Self- reset Illumin ated Flat
Button, 24V, 1 NO
Green Self- reset Illumin ated Flat
Button, 36V, 1 NO
Green Self- reset Illumin ated Flat
Button , 48V, 1 NC
Red Self- reset Illumin ated Flat Button
, 110V, 1 NC

Outline Drawing and Dimensions

Two- position Indexing Key Button, Key Pulled out from L eft, 1 NO Two- position Indexing Key Button, Key Pulled out from L eft a nd Right, 1 NC Two- position Self-reset Key Button, Key Pulled out from L eft, 1 NO Three- position Indexing Key Button, Key Pullable at Each Position, 2 NO Three- position Indexing Key Button, Key Pulled out from L eft, 2 NC Three- position Indexing Key Button, Key Pulled out from Middle, 1 NO1NC

56.4

Order Model

RDA5-B5
RDA5-BD5

Meaning

Dou ble-Key Self -r eset Bu tton, 1NO1NC Dou ble-Key Self -r eset Illu minated Button, 1NO1NC

Emergency Stop Button-Selection Rules

Order Model

Meaning

RDA5-S54 Emergency Stop Button ,

Emergency Stop Button , 1NO1NC

MP016S

Mental Push Button Series

Photo	Parameter	Contour
MP016S/H11-△▲D	Metal point light button switch Mounting hole dimension: φ16mm Switch rating:3A/250VAC Switch combination:1NO1NC/2NO2NC Operation types: nonstick / Self-lock Head shape: high discoid Shell material: stainless steel/nickel-plated brass Lamp mode: single point IP grade: IP40/IP67	End view Interpolation position diagram
MP016S/H11-△▲E	Metal point light button switch Mounting hole dimension: φ16mm Switch rating:3A/250VAC Switch combination:1NO1NC/2NO2NC Operation types: nonstick / Self-lock Head shape: high discoid Shell material: stainless steel/ nickel-plated brass Lamp mode: Ring IP grade:IP40/IP67	Interpolation position diagram
MP016S/F11-△▲D	Metal point light button switch Mounting hole dimension: φ16mm Switch rating:3A/250VAC Switch combination:1NO1NC/2NO2NC Operation types: nonstick / Self-lock Head shape: discoid Shell material: stainless steel/ nickel-plated brass Lamp mode: single point IP grade: IP40/IP67	End view Interpolation position diagram
MP016S/F11-△▲E	16mm Ring button switch with lamp Mounting hole dimension: φ16mm Switch rating:3A/250VAC Switch combination:1NO1NC/2NO2NC Operation types: nonstick / Self-lock Head shape: high discoid Shell material: stainless steel/ nickel-plated brass Lamp mode: Ring IP grade: IP40/IP67	End view Interpolation position diagram

MP016S

MP016S

Mental Push Button Series

Photo	Parameter
MP016S/F11Z	Metal button switch Mounting hole dimension: φ16mm Switch rating: 3A/250VAC Switch combination: 1NO1NC/2NO2NC Operation types: nonstick / self-lock Head shape: discoid Shell material: stainless steel/ brass chrome plating IP grade: IP40/IP67	End view Interpolation position diagram
	Metal button switch Mounting hole dimension: φ16mm Switch rating: 3A/250VAC Switch combination: 1NO1NC/2NO2NC Operation types: nonstick / self-lock Head shape: high discoid Shell material: stainless steel/ brass chrome plating IP grade: IP40/IP67	End view Interpolation position diagram
	φ16 Angle metal button switch with lamp Mounting hole dimension: φ16mm Switch rating: 3A/250VAC Switch combination: 1NO Operation types: nonstick Head shape: discoid Shell material: stainless steel/ brass chrome plating Lamp mode: single point IP grade: IP65	Interpolation position diagram
	Switch rating: 3A/250VAC Switch combination: 1NO Operation types: nonstick Head shape: discoid Shell material: stainless steel/ brass chrome plating Lamp mode: ring IP grade: IP65	End view Interpolation position diagram

MP016S

RDA

Hoist Crane Switch

Product Overview

RDA series Hoist Crane Switch are suitable for AC 50Hz or 60Hz,voltage up to 380V,and DC working voltage up to 220Vin circuit control systems. Suitable for open-air environments with rain, snow, and heavy dust, such as remote control of cranes, electric hoists and other equipment. The product complies with the lEC 60947-5-1 standard.

Selection Guide

NormaI Operating and Installation Conditions

□Ambient air temperature :-5°C\~+40°C,with 24-hours average not exceeding +35°C:

□Altitude: Not exceeding 2000 meters;

□ Atmosp heric conditions: Relative humidity does not exceed 50% at amaximum temperature is+40°C;higher is permissible at lower temperatures(e.g., up to 90% at+20°C. )Special measures shall be taken for occasional condensation due to temperature changes;

□ Pollution degree: Level 3;

□Installation category: Category II ;

□No significant shaking, impact vibration, or exposure to rain and snow.

□ Free from explosion hazard, and no presence of gases or dust capable of corroding metals or degrading insulation.

Outline and Installation Dimensions

Order Instructions

□When placing an order please specify the complete model, specification ,and quantityof the button.

□Example:50 pieces of RDA-63 type buttons mean 50 pieces of buttons with up, down, left, right, front ,and back types.

RDD6

Series signal lamps

Product Overview

RDD6/16 Series Signal Lamps adopt high-brightness pure-color LED light-emitting chips as the light source, with long service life, low energy consumption, and small volume. The components are made of imported materials,firm and durable, and wear-resistant. They can work normally under the vibration freguency of 2-80Hz and acceleration of 0.7G. They have reliable performance, beautiful appearance, and complete specifications. They are suitable for use as indication signals, pre-warning signals, accident signals, and other indication signals in the circuits of equipment such as electric power. telecommunication machine tools, ships, textiles, printing, and mining machinery. The product complies with the IEC 60947-5 standard.

Normal Operating Conditions and Installation Conditions

□ Ambient air temperature : - 5 ^ { \circ } \mathsf { C } ~ + 4 0 ^ { \circ } \mathsf { C } and the average value within 24 hours does not exceed +35°℃:

□Altitude:Not exceeding 2000m;

□Atmospheric conditions: When the maximum temperature is+40°C the relative humidity of the air does not exceed 50%. At lower temperatures, a higher relative humidity is allowed, for example, reaching 90 % a { t } + 2 0 ~ ^ { \circ } { C } Special measures should be taken for the condensation occasionally generated due to temperature changes;

□Pollution degree: Grade 3;

□Installation category: Category III;

□Places without significant shaking, impact vibration, and without rain and snow invasion;

□In a medium without explosion hazard, and there is no gas and dust in the

medium sufficient to corrode metals and damage insulation.

Product Features

Mounting Hole Size: φ22mm,φ25mm can be achieved by selecting a reducing ring; Components are made of imported materials, firm and durable, and wear - resistant Built -in screw-type wiring, safer and more convenient;

Outline and Installation Dimensions

RDD6<br>H

RDD16

TME

Limit Switch

Features

Double circuit type of limit switch

Highly rigid construction, consists of intensive plastic and aluminum cast (head and cover snugly fit in box)

Small volume, water-proof and oil-proof construction

Built-in basic switch with double spring mechanism, longer mechanical life

Smooth operation with greater OT

Easy-to-wire circuit opening design

Wide varity of actuators, easily use

Ratings

Characteristics

Appearance and dimension

TXCK-M

Limit Switch

Features

Strong metal outer shell, swing arm max. ±95°

Long life (20,000,000 mechanical operations)

Stainless steel idler wheel, punch and spring

Selective PG11 cable gland

Specifications

Appearance and dimension

Appearance and dimension

CWL

Limit Switch

Features

Double-circuit type of limit switch is widely used

With strong aluminum cast outer shell

High mechanical strength

Water-proof, oil-proof construction

Structure preventing oil, water and pressure

Indicating plate with setting position is installed in it, so it is easy to maintain

Various of actuators is taken convenience for using

Built-in contact stand has double-spring, so it has long mechanical life

Ratings

Characteristics

THL

Features

Limit Switch

Metallic bottom shell

Stainless steel roller, punch and spring

Strong electric property 10A, 250V, for 500,000 times

Electrical life

Appearance and dimension

CM

Micro Switch

Features

Various of actuators, action position is adjustable (such as Cm1701)

High switch on and off capacity (15A)

High accuracy

Wide range of operation speed

Each type of CM series has solder terminal, screw terminal and tab terminal are selective

Add A for solder terminal, add C for tab terminal, blank for screw terminal

Ratings

Characteristics

Operating characteristics

Definitions of operating characteristics:

OF: operating force

Force needed to add to the executer unit to actuate switch contact

RF: releasing force

Force needed to add to the executer unit to make the switch contact back to normal position TF: total force

Force needed to make executer unit move from free position to limitation position FP: free position

Primary position of executer unit without external force adding to executer unit

OP: operating position

The position of executer unit in case of the contact rapidly moving to the contact position for action

RP: releasing position

The position of executer unit in case of the contact rapidly backing to normal position to action contact position

TTP: total travel position

The position of executer unit in case of executer unit reaching the limitation position PT: pre-travel

The distance or angle that the executer unit passes since free position to action position OT: over-travel

The distance or angle that the executer unit surpasses action position

MD: movement differential

The distance or angle from action position to reversion position

TT: total travel

The distance or angle represents the movement till action and the total movement till action and the total movement after all actions.

CM-1701 (Z-15GW-B)

CM-1702 (Z-15GW21-B)

CM-1703 (Z-15GW2-B)

CM-1704 (Z-15GW22-B)

CM-1743 (Z-15GW2277-B)	CM-1705(Z-15HW78-B)
CM-1306 (Z-15GD-B)
CM-1308 (Z-15GQ22-B)
CM-1300 (Z-15G-B)
CM-1303 (Z-15GL2-B)

Appearance and dimension