该页无缩略图
外圆车刀杆(负型)External Turning Toolholder (Negative)
MWLNR/L
| 订货号Ordering Code | 尺寸Dimension(mm) | 匹配刀片 | 刀垫Shim | 销钉Pin | 压板Clamp | 双头螺丝Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | C | 0 | R | L | ||||
| MWLNR/L2525M06T3 | 25 | 25 | 150 | 28 | 25 | 32 | WN**06T3** | DWN0603M | SPM050130 | CAM01 | SDM050200 | TH20LTH30L | • | |
| MWLNR/L2020K0604 | 20 | 20 | 125 | 28 | 20 | 25 | WN**0604** | DWN0603M | SPM050130 | CAM01 | SDM050200 | TH20LTH30L | ● | |
| MWLNR2525M0604 | 20 | 20 | 150 | 28 | 25 | 32 | WN**0604** | DWN0603M | SPM050130 | CAM01 | SDM050200 | TH20LTH30L | ||
| MWLNR/L2020K08 | 20 | 20 | 125 | 32 | 20 | 25 | WN**0804** | DWN0804M | SPM060170 | CAM02 | SDM060200 | TH25LTH30L | • | |
| MWLNR/L2525M08 | 25 | 25 | 150 | 32 | 25 | 32 | WN**0804** | DWN0804M | SPM060170 | CAM02 | SDM060250 | TH25LTH30L | ||
| MWLNR/L3232P08 | 32 | 32 | 170 | 32 | 32 | 40 | WN**0804** | DWN0804M | SPM060170 | CAM02 | SDM060280 | TH25LTH30L | • | |
●标准库存 Stock需预定 Available upon Order
外圆车刀杆(正型)External Turning Toolholder(Positive)
SCLCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | O | 6 | R | L | |
| SCLCR/L1010F06 | 10 | 10 | 80 | 12 | 10 | 12 | CC**0602** | SI60M025060-03510 | TT08P | ||
| SCLCR/L1212H09 | 12 | 12 | 100 | 16 | 12 | 16 | CC**09T3** | SI60M040100-05812 | TT15P | ● | O |
| SCLCR/L1616H09 | 16 | 16 | 100 | 16 | 16 | 20 | CC**09T3** | SI60M040100-05812 | TT15P | ||
| SCLCR/L2020K09 | 20 | 20 | 125 | 16 | 20 | 25 | CC**09T3** | SI60M040100-05812 | TT15P | ● | ● |
| SCLCR/L2525M12 | 25 | 25 | 150 | 20 | 25 | 32 | CC**1204** | SI60M050120-07012 | TT20P | ● | ● |
●标准库存 Stock 需预定 Available upon Order
SDJCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | CO | L | R | L | |
| SDJCR/L1010F07 | 10 | 10 | 80 | 15 | 10 | 12 | DC**0702** | SI60M025060-03510 | TT08P | ● | ● |
| SDJCR1212H07 | 12 | 12 | 100 | 15 | 12 | 16 | DC**0702** | SI60M025060-03510 | TT08P | ● | |
| SDJCR/L1616H11 | 16 | 16 | 100 | 20 | 16 | 20 | DC**11T3** | SI60M040100-05812 | TT15P | ● | ● |
| SDJCR/L2020K11 | 20 | 20 | 125 | 20 | 20 | 25 | DC**11T3** | SI60M040100-05812 | TT15P | ● | ● |
| SDJCR/L2525M11 | 25 | 25 | 150 | 20 | 25 | 32 | DC**11T3** | SI60M040100-05812 | TT15P | ● | |
●标准库存 Stock需预定 Available upon Order
SSDCN
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | |||||
| H | B | LF | OHX | HF | WF | O | 4 | |||
| SSDCN1212H09 | 12 | 12 | 80 | 15 | 12 | 6 | SC**09T3** | SI60M040100-05812 | TT15P | |
| SSDCN1616H09 | 16 | 16 | 100 | 15 | 16 | 8 | SC**09T3** | SI60M040100-05812 | TT15P | ● |
| SSDCN2020K09 | 20 | 20 | 125 | 15 | 20 | 10 | SC**09T3** | SI60M040100-05812 | TT15P | O |
| SSDCN2525M12 | 25 | 25 | 150 | 20 | 25 | 12.5 | SC**1204** | SI60M050120-07012 | TT20P | |
●标准库存 Stock需预定 Available upon Order
STGCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | O | A | R | L | |
| STGCR1010F09 | 10 | 10 | 80 | 12 | 10 | 12 | TC**0902** | SI60M022060-03008 | TT06P | ● | |
| STGCR/L1212H11 | 12 | 12 | 100 | 16 | 12 | 16 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| STGCR/L1616H11 | 16 | 16 | 100 | 20 | 16 | 20 | TC**1102** | SI60M025060-03510 | TT08P | ● | ● |
| STGCR/L2020K16 | 20 | 20 | 125 | 25 | 20 | 25 | TC**16T3** | SI60M040100-05812 | TT15P | ||
| STGCR/L2525M16 | 25 | 25 | 150 | 25 | 25 | 32 | TC**16T3** | SI60M040100-05812 | TT15P | ||
●标准库存 Stock需预定 Available upon Order
外圆车刀杆(正型)External Turning Toolholder(Positive)
SVJCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | O | P | R | L | |
| SVJCR1212H11 | 12 | 12 | 100 | 25 | 12 | 16 | VC**1103** | SI60M025060-03510 | TT08P | ||
| SVJCR/L1616H11 | 16 | 16 | 100 | 25 | 16 | 20 | VC**1103** | SI60M025060-03510 | TT08P | • | |
| SVJCR/L2020K16 | 20 | 20 | 125 | 35 | 20 | 25 | VC**1604** | SI60M040100-05812 | TT15P | • | • |
| SVJCR/L2525M16 | 25 | 25 | 150 | 35 | 25 | 32 | VC**1604** | SI60M040100-05812 | TT15P | • | • |
●标准库存 Stock需预定 Available upon Order
SWLCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H | B | LF | OHX | HF | WF | Insert | O | A | R | L | |
| SWLCR/L1212H06 | 12 | 12 | 100 | 15 | 12 | 16 | WC**06T3** | SI60M040100-05812 | TT15P | ||
| SWLCR/L1616H06 | 16 | 16 | 100 | 15 | 16 | 20 | WC**06T3** | SI60M040100-05812 | TT15P | • | • |
| SWLCR/L2020K06 | 20 | 20 | 125 | 15 | 20 | 25 | WC**06T3** | SI60M040100-05812 | TT15P | • | |
| SWLCR/L2525M06 | 25 | 25 | 150 | 20 | 25 | 32 | WC**06T3** | SI60M040100-05812 | TT15P | ||
●标准库存 Stock 需预定 Available upon Order
内孔车刀杆型号表示规则Internal Turning Toolholders Identification System
S
16
M
①
②
③
C
带冷却孔钢刀杆
A Steel with coolant hole 硬质合金刀杆
C Carbide shank 带冷却孔硬质合金刀杆
E Carbide bar with coolant hole 钢刀杆
S Steel shank
①刀杆材质 Tool Material
S
| ③刀柄长度Tool Length | |
| F | 80 |
| H | 100 |
| K | 125 |
| M | 150 |
| N | 160 |
| Q | 180 |
| R | 200 |
| S | 250 |
| T | 300 |
| U | 350 |
| V | 400 |
⑤
④
⑤刀片形状 Insert Shape
80°菱形
C 80°Rhombic 55°菱形
D 55°Rhombic 圆形
R Round 正方形
S Square 正三角形
T Triangle 35°菱形
V 35°Rhombic
W 六边形 Trigon
| ②刀柄直径Shank Diameter | |
| 08 | 8 |
| 10 | 10 |
| 12 | 12 |
| 16 | 16 |
| 20 | 20 |
| 25 | 25 |
| 32 | 32 |
| 40 | 40 |
④夹紧方式 Method of Holding
| M | 双重夹紧型Double Clamp Type |
| C | 压板夹紧型Top Clamp Type |
| P | 杠杆锁紧型Laver Lock Type |
| S | 螺钉夹紧型Screw-on Type |
| ⑥主偏角Cutting Edge Angle | |
| K | 75° |
| L | 95° |
| F | 91° |
| Q | 107.5° |
| U | 93° |
| W | 60° |
| X | 120° |
| ⑦刀片后角Insert Clearanoe Angle | |
| C | 7° |
| B | 5° |
| N | 0° |
| P | 11° |
| ⑨切削刃长度(mm)Cutting Edge Length(mm) | ||||||
| 刀片内接圆Insert IC(mm) | 刀片形状Insert Shape | |||||
| 正方形Square | 正三角形Triangle | 圆形Round | 80°菱形80°Rhombic | 55°菱形55°Rhombic | 35°菱形35°Rhombic | |
| 6 | - | - | 06 | - | - | - |
| 6.35 | - | 11 | - | 06 | 07 | 11 |
| 7.94 | - | 13 | - | - | - | - |
| 8 | - | - | 08 | - | - | - |
| 9.525 | 09 | 16 | - | 09 | 11 | 16 |
| 10 | - | - | 10 | - | - | - |
| 12 | - | - | 12 | - | - | - |
| 12.7 | - | 22 | - | 12 | 15 | - |
| 15.875 | 15 | 27 | - | 16 | - | - |
| 16 | - | - | 16 | - | - | - |
| 19.05 | 19 | - | 19 | - | - | - |
| 20 | - | - | 20 | - | - | - |
| 25 | - | - | 25 | - | - | = |
| 25.4 | 25 | - | - | - | - | - |
| 32 | - | - | 32 | - | - | 1 |
SCLCR/L
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | A | R | L | ||
| S08K-SCLCR/L06 | 10 | 8 | 5.5 | 125 | 12 | 7 | 13 | CC**0602** | SI60M025060-03510 | TT08P | ● | ● |
| S10K-SCLCR/L06 | 12 | 10 | 6.5 | 125 | 15 | 9 | 12 | CC**0602** | SI60M025060-03510 | TT08P | ● | |
| S12M-SCLCR/L06 | 16 | 12 | 8 | 150 | 18 | 11 | 10 | CC**0602** | SI60M025060-03510 | TT08P | ||
| S12M-SCLCR/L09 | 16 | 12 | 8 | 150 | 18 | 11 | 12 | CC**09T3** | SI60M040100-05812 | TT15P | ||
| S16Q-SCLCR/L09 | 20 | 16 | 10 | 180 | 24 | 15 | 10 | CC**09T3** | SI60M040100-05812 | TT15P | ||
| S20R-SCLCR/L09 | 25 | 20 | 12 | 200 | 30 | 18 | 8 | CC**09T3** | SI60M040100-05812 | TT15P | ||
| S25S-SCLCR/L09 | 32 | 25 | 16 | 250 | 38 | 23 | 6 | CC**09T3** | SI60M040100-05812 | TT15P | ||
| S25S-SCLCR/L12 | 32 | 25 | 16 | 250 | 38 | 23 | 8 | CC**1204** | SI60M050120-07012 | TT20P | • | |
●标准库存 Stock 需预定 Available upon Order
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | O | A | R | L | |
| S08K-SCKCR/L06 | 10 | 8 | 5.5 | 125 | 12 | 7 | 13 | CC**0602** | SI60M025060-03510 | TT08P | ● | O |
| S10K-SCKCR/L06 | 12 | 10 | 6.5 | 125 | 15 | 9 | 12 | CC**0602** | SI60M025060-03510 | TT08P | ● | O |
| S12M-SCKCR/L06 | 16 | 12 | 8 | 150 | 18 | 11 | 10 | CC**0602** | SI60M025060-03510 | TT08P | O | O |
| S12M-SCKCR/L09 | 16 | 12 | 8 | 150 | 18 | 11 | 12 | CC**09T3** | SI60M040100-05812 | TT15P | O | |
| S16Q-SCKCR/L09 | 20 | 16 | 10 | 180 | 24 | 15 | 10 | CC**09T3** | SI60M040100-05812 | TT15P | O | |
| S20R-SCKCR/L09 | 25 | 20 | 12 | 200 | 30 | 18 | 8 | CC**09T3** | SI60M040100-05812 | TT15P | O | O |
| S25S-SCKCR/L09 | 32 | 25 | 16 | 250 | 38 | 23 | 6 | CC**09T3** | SI60M040100-05812 | TT15P | O | |
●标准库存 Stock 需预定 Available upon Order
SCLCR/L-A16
内孔车刀杆Internal Turning Toolholder
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CCO | A | R | L | |
| S07M-SCLCR/L06-A16 | 9 | 16 | 4.25 | 150 | 18 | 15 | 15 | CC**0602** | SI60M025060-03510 | TT08P | ● | O |
| S08M-SCLCR/L06-A16 | 10 | 16 | 5 | 150 | 20 | 15 | 13 | CC**0602** | SI60M025060-03510 | TT08P | O | |
| S10M-SCLCR/L06-A16 | 13 | 16 | 6 | 150 | 26 | 15 | 12 | CC**0602** | SI60M025060-03510 | TT08P | ● | |
| S12M-SCLCR/L06-A16 | 15 | 16 | 7 | 150 | 28 | 15 | 10 | CC**0602** | SI60M025060-03510 | TT08P | O | |
●标准库存 Stock 需预定 Available upon Order
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CIO | 4 | R | L | |
| S10K-SDUCR/L07 | 12 | 10 | 7 | 125 | 15 | 9 | 10 | DC**0702** | SI60M025060-03510 | TT08P | ||
| S12M-SDUCR/L07 | 16 | 12 | 9 | 150 | 18 | 11 | 8 | DC**0702** | SI60M025060-03510 | TT08P | ● | |
| S16Q-SDUCR/L07 | 20 | 16 | 11 | 180 | 24 | 15 | 6 | DC**0702** | SI60M025060-03510 | TT08P | ||
| S16Q-SDUCR/L11 | 20 | 16 | 11 | 180 | 24 | 15 | 6 | DC**11T3** | SI60M040100-05812 | TT15P | ● | |
| S20R-SDUCR/L11 | 25 | 20 | 13 | 200 | 30 | 18 | 6 | DC**11T3** | SI60M040100-05812 | TT15P | ● | |
| S25S-SDUCR/L11 | 32 | 25 | 16 | 250 | 38 | 23 | 4 | DC**11T3** | SI60M040100-05812 | TT15P | ● | ● |
●标准库存 Stock 需预定 Available upon Order
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CO | L | R | L | |
| S10K-SDQCR/L07 | 12 | 10 | 7 | 125 | 15 | 9 | 10 | DC**0702** | SI60M025060-03510 | TT08P | ● | O |
| S12M-SDQCR/L07 | 16 | 12 | 9 | 150 | 18 | 11 | 8 | DC**0702** | SI60M025060-03510 | TT08P | O | |
| S16Q-SDQCR/L07 | 20 | 16 | 11 | 180 | 24 | 15 | 6 | DC**0702** | SI60M025060-03510 | TT08P | O | |
| S16Q-SDQCR/L11 | 20 | 16 | 11 | 180 | 24 | 15 | 6 | DC**11T3** | SI60M040100-05812 | TT15P | ||
| S20R-SDQCR/L11 | 25 | 20 | 13 | 200 | 30 | 18 | 6 | DC**11T3** | SI60M040100-05812 | TT15P | O | |
| S25S-SDQCR/L11 | 32 | 25 | 16 | 250 | 38 | 23 | 4 | DC**11T3** | SI60M040100-05812 | TT15P | • | • |
●标准库存 Stock需预定 Available upon Order
SDXCR/L
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | O | L | R | L | |
| S08K-SDXCR/L07 | 10 | 8 | 5.5 | 125 | 12 | 7 | 12 | DC**0702** | SI60M025060-03510 | TT08P | ● | O |
| S10K-SDXCR/L07 | 12 | 10 | 6.5 | 125 | 15 | 9 | 10 | DC**0702** | SI60M025060-03510 | TT08P | ● | O |
| S12M-SDXCR/L07 | 16 | 12 | 8 | 150 | 18 | 11 | 8 | DC**0702** | SI60M025060-03510 | TT08P | O | |
| S16Q-SDXCR/L07 | 20 | 16 | 10 | 180 | 24 | 15 | 6 | DC**0702** | SI60M040100-05812 | TT08P | O | |
| S20R-SDXCR/L11 | 25 | 20 | 12 | 200 | 30 | 18 | 6 | DC**11T3** | SI60M040100-05812 | TT15P | ||
| S25S-SDXCR/L11 | 32 | 25 | 14 | 250 | 38 | 23 | 4 | DC**11T3** | SI60M040100-05812 | TT15P | O | |
●标准库存 Stock 需预定 Available upon Order
内孔车刀杆Internal Turning Toolholder
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | O | P | R | L | |
| S12M-SSKCR/L09 | 16 | 12 | 9 | 150 | 18 | 11 | 10 | SC**09T3** | SI60M040100-05812 | TT15P | O | O |
| S16Q-SSKCR/L09 | 20 | 16 | 11 | 180 | 24 | 15 | 10 | SC**09T3** | SI60M040100-05812 | TT15P | ● | O |
| S20R-SSKCR/L09 | 25 | 20 | 13 | 200 | 30 | 18 | 8 | SC**09T3** | SI60M040100-05812 | TT15P | ● | O |
| S25S-SSKCR/L12 | 32 | 25 | 17 | 250 | 38 | 23 | 6 | SC**1204** | SI60M050120-07012 | TT20P | O | O |
●标准库存 Stock 需预定 Available upon Order
STUCR/L
| 订货号Ordering Code | Dimensi | 尺寸on(mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CCO | L | R | L | |
| S08K-STUCR/L09 | 10 | 8 | 5.5 | 125 | 12 | 7 | 15 | TC**0902** | SI60M022060-03008 | TT06P | ● | O |
| S10K-STUCR/L09 | 12 | 10 | 6.5 | 125 | 15 | 9 | 13 | TC**0902** | SI60M022060-03008 | TT06P | ● | O |
| S10K-STUCR/L11 | 12 | 10 | 6.5 | 125 | 15 | 9 | 12 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| S12M-STUCR/L11 | 16 | 12 | 8 | 150 | 18 | 11 | 10 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| S16Q-STUCR/L11 | 20 | 16 | 10 | 180 | 24 | 15 | 8 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| S20R-STUCR11 | 25 | 20 | 12 | 200 | 30 | 18 | 6 | TC**1102** | SI60M025060-03510 | TT08P | ● | |
| S20R-STUCR/L16 | 25 | 20 | 12 | 200 | 30 | 18 | 4 | TC**16T3** | SI60M040100-05812 | TT15P | ● | O |
| S25S-STUCR16 | 32 | 25 | 16 | 250 | 38 | 23 | 6 | TC**16T3** | SI60M040100-05812 | TT15P | ● | |
●标准库存 Stock 需预定 Available upon Order
STWCR/L
STFCR/L
| 订货号Ordering Code | 尺寸Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | |||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | J | L | R | L | |
| S08K-STWCR/L09 | 10 | 8 | 6 | 125 | 12 | 7 | 15 | TC**0902** | SI60M022060-03008 | TT06P | ● | O |
| S10K-STWCR/L11 | 12 | 10 | 8 | 125 | 15 | 9 | 10 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| S12M-STWCR/L11 | 16 | 12 | 9 | 150 | 18 | 11 | 8 | TC**1102** | SI60M025060-03510 | TT08P | ● | O |
| S16Q-STWCR/L11 | 20 | 16 | 11 | 180 | 24 | 15 | 6 | TC**1102** | SI60M025060-03510 | TT08P | O | O |
| S20R-STWCR11 | 25 | 20 | 13 | 200 | 30 | 18 | 4 | TC**1102** | SI60M025060-03510 | TT08P | O | |
| S20R-STWCR/L16 | 25 | 20 | 15 | 200 | 30 | 18 | 8 | TC**16T3** | SI60M040100-05812 | TT15P | O | O |
| S25S-STWCR/L16 | 32 | 25 | 17 | 250 | 38 | 23 | 6 | TC**16T3** | SI60M040100-05812 | TT15P | O | |
●标准库存 Stock 需预定 Available upon Order
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | 小 | L | R | L | |
| S08K-STFCR/L09 | 10 | 8 | 5.5 | 125 | 12 | 7 | 15 | TC**0902** | SI60M022060-03008 | TT06P | O | |
| S10K-STFCR/L09 | 12 | 10 | 6.5 | 125 | 15 | 9 | 10 | TC**0902** | SI60M022060-03008 | TT06P | ||
| S12M-STFCR/L09 | 16 | 12 | 8 | 150 | 18 | 11 | 8 | TC**0902** | SI60M022060-03008 | TT06P | O | |
| S12M-STFCR/L11 | 16 | 12 | 8 | 150 | 18 | 11 | 6 | TC**1102** | SI60M025060-03510 | TT08P | ||
| S16Q-STFCR/L11 | 20 | 16 | 10 | 180 | 24 | 15 | 4 | TC**1102** | SI60M025060-03510 | TT08P | • | |
| S20R-STFCR/L11 | 25 | 20 | 12 | 200 | 30 | 18 | 8 | TC**1102** | SI60M025060-03510 | TT08P | • | • |
| S20R-STFCR/L16 | 25 | 20 | 12 | 200 | 30 | 18 | 6 | TC**16T3** | SI60M040100-05812 | TT15P | ● | O |
| S25S-STFCR/L16 | 32 | 25 | 16 | 250 | 18 | 23 | TC**16T3** | SI60M040100-05812 | TT15P | ● | ||
●标准库存 Stock 需预定 Available upon Order
SVUCR/L
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CCO | A | R | L | |
| S16Q-SVUCR/L11 | 20 | 16 | 12 | 180 | 25 | 15 | 10 | VC**1103** | SI60M025060-03510 | TT08P | • | O |
| S20R-SVUCR/L11 | 25 | 20 | 16 | 200 | 25 | 18 | 8 | VC**1103** | SI60M025060-03510 | TT08P | ||
| S25S-SVUCR/L16 | 33 | 25 | 20 | 250 | 32 | 23 | 8 | VC**1604** | SI60M040100-05812 | TT15P | • | • |
●标准库存 Stock 需预定 Available upon Order
SWLCR/L
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | CCO | L | R | L | |
| S12M-SWLCR/L06 | 16 | 12 | 8 | 150 | 18 | 11 | 12 | WC**06T3** | SI60M040100-05812 | TT15P | ||
| S16Q-SWLCR/L06 | 20 | 16 | 10 | 180 | 24 | 14.8 | 10 | WC**06T3** | SI60M040100-05812 | TT15P | ● | • |
| S20R-SWLCR/L06 | 25 | 20 | 12 | 200 | 30 | 18.4 | 8 | WC**06T3** | SI60M040100-05812 | TT15P | ||
| S25S-SWLCR/L06 | 32 | 25 | 16 | 250 | 38 | 23.4 | 6 | WC**06T3** | SI60M040100-05812 | TT15P | ||
●标准库存 Stock需预定 Available upon Order
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | 1 | L | R | L | |
| S08K-SCLPR/L06 | 10 | 8 | 5.5 | 125 | 12 | 7 | 13 | CP**0602** | SI60M025060-03510 | TT08P | ● | |
| S10K-SCLPR/L06 | 12 | 10 | 6.5 | 125 | 15 | 9 | 12 | CP**0602** | SI60M025060-03510 | TT08P | ● | |
| S12M-SCLPR/L06 | 16 | 12 | 8 | 150 | 18 | 11 | 10 | CP**0602** | SI60M025060-03510 | TT08P | ● | ● |
| S12M-SCLPR/L09 | 16 | 12 | 8 | 150 | 18 | 11 | 12 | CP**09T3** | SI60M040100-05812 | TT15P | ● | ● |
| S16Q-SCLPR/L09 | 20 | 16 | 10 | 180 | 24 | 15 | 10 | CP**09T3** | SI60M040100-05812 | TT15P | ● | ● |
| S20R-SCLPR/L09 | 25 | 20 | 12 | 200 | 30 | 18 | 8 | CP**09T3** | SI60M040100-05812 | TT15P | ● | O |
| S25S-SCLPR/L09 | 32 | 25 | 16 | 250 | 38 | 23 | 6 | CP**09T3** | SI60M040100-05812 | TT15P | ● | ● |
●标准库存 Stock 需预定 Available upon Order
STFPR/L
| 订货号Ordering Code | Dimens | 尺寸ion (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | |||||
| DMIN1 | DCON | WF | LF | OHN | H | α° | Insert | O | 6 | R | |
| S10K-STFPR1102 | 12 | 10 | 6.5 | 125 | 15 | 9 | 12 | TP**1102** | SI60M025060-03510 | TT08P | |
| S12M-STFPR1102 | 16 | 12 | 8 | 150 | 18 | 11 | 10 | TP**1102** | SI60M025060-03510 | TT08P | |
| S16Q-STFPR1102 | 20 | 16 | 10 | 180 | 24 | 15 | 8 | TP**1102** | SI60M025060-03510 | TT08P | |
| S20R-STFPR1102 | 25 | 20 | 12 | 200 | 30 | 18 | 6 | TP**1102** | SI60M025060-03510 | TT08P | O |
| S20R-STFPR16T3 | 25 | 20 | 12 | 200 | 30 | 18 | 4 | TP**16T3** | SI60M040100-05812 | TT15P | |
| S25S-STFPR16T3 | 32 | 25 | 16 | 250 | 38 | 23 | 6 | TP**16T3** | SI60M040100-05812 | TT15P | O |
●标准库存 Stock需预定 Available upon Order
切断切槽刀片型号表示规则GZ、GK系列刀片型号表示规则
Parting and Grooving Series Insert Identification System GZ. GK Series Insert Identification System
GZ D 40 02 R 15 FG
【①】
②
③
【④
⑤
6
⑦】
①系列总称Series
GK
GZ
③刀片宽度 Insert Width 30=3.0mm 40=4.0mm
⑤导程角方向
Hand of Insert R=右手
R=Right Hand L=左手
L=Left Hand □=中置 □=Neutral
②刃数
Number of Cutting
Edge
S=单刃
S=Single
D=双刃
D=Double
④刀尖圆弧半径
Corner Radius
02=0.2mm
04=0.4mm
20=2.0mm
⑥导程角 Lead Angle 15=15°
| ⑦槽型Geometry | |
| 第一个字母First Character | 第二个字母Second Character |
| F=低进给F=Low Feed | C=切断C=Cutting off |
| M=中等进给M=Medium feed | T=车削T=Turning |
| R=高进给R=High Feed | G=切槽G=Grooving |
| O=特定范围优化O=Optimize forSpecial Range | R=仿形车削R=Profiling |
切断切槽刀片型号表示规则GB系列刀片型号表示规则
Parting and Grooving Series Insert Identification System GB Series Insert Identification System
GB (R) 4 125 R - 020
【①】
②
【③】
【④
⑤
【6】
①系列总称Series
GB
3
③刀片尺寸 Insert Size
4
IC=9.525mm
IC=12.7mm
②刀片类型
Insert Type R=圆头
R= Full Radius □=方头
□= Squaring
④刀片宽度 Insert Width
125=1.25mm
⑤刀片方向
Hand of InsertR=右手
R=Right HandL=左手
L=Left Hand
0.2=0.2mm
⑥刀尖圆弧半径 Corner Radius
切断切槽刀杆型号表示规则GZ、GK系列刀杆型号表示规则
Parting and Grooving Series Tool holder Identification System GZ, GK Series Tool Holder Identification System
GZ E R 2525 -4 T25 -
切断切槽刀杆型号表示规则GB系列刀杆型号表示规则
Parting and Grooving Series Tool holder Identification System GB Series Tool Holder Identification System
2525
①】
4-□
②
④
【③】
【⑤】
【⑦】
①系列总称Series
GB
③刀杆方向
Hand of Insert
R=右手
R=Right Hand
L=左手
L=Left Hand
②加工类型
Processing Type
E=外圆加工
E=External Processing
I=内孔加工
I=Internal Processing
| ⑤刀杆长度Tool Holder Length | |
| 代号Symbol | 长度Length |
| K | 125mm |
| M | 150mm |
| Q | 180mm |
| R | 200mm |
④刀柄尺寸 Shank Size
外圆刀杆：高度\*宽度External Holder:Height\*Width
内孔刀杆：
最小加工直径\*柄径
Internal Bar:
Min processing
Diameter\*Bar
Diameter
| ⑥刀片尺寸Insert Size | |
| 3 | IC=9.525mm |
| 4 | IC=12.7mm |
| ⑦适合刀片宽度范围Groove Size | |
| 15 | 1.0≤W<2.5 |
| 25 | 2.5≤W<3.3 |
| 35 | 3.3≤W |
| 仅搭配GB4的外圆刀杆需做以上区别Only for externalholders with GB4inserts | |
切断切槽刀片一览表
Overview of Parting and Grooving Inserts
| 外形Shape | 槽型Geometry | 应用Application | 宽度Width | 页码Page |
 | FG | 精密切槽Precision Grooving | 3.0-6.0(mm) | P53 |
 | OR | 精密仿形Precision Profiling | 3.0-6.0(mm) | P53 |
 | GB | 精密切槽Precision Grooving | 0.5-4.3(mm) | P54 |
切断切槽刀片 Parting and Grooving Inserts
FG
精密切槽加工刀片 Precision Grooving Inserts
OR
订货号Ordering Code | 尺寸(mm)Dimension (mm) | 涂层硬质合金Coated | 硬质合金Uncoated | |||||
| CW | RE | L | W1 | S | GS3125 | GS9125 | ||
| GZD3002-FG | 3.0 | 0.2 20.4 | 2.3 | 4.6 | ● | O | ||
| GZD3004-FG | 3.0 | 0.4 | 20.4 | 2.3 | 4.6 | ● | O | |
| GZD4002-FG | 4.0 | 0.2 | 24.0 | 3.3 | 4.8 | O | O | |
| GZD4004-FG | 4.0 | 0.4 | 24.0 | 3.3 | 4.8 | ● | ● | |
| GZD5002-FG | 5.0 | 0.2 | 24.0 | 3.3 | 4.8 | ● | O | |
| GZD5004-FG | 5.0 | 0.4 | 24.0 | 3.3 | 4.8 | O | O | |
| GZD6002-FG | 6.0 | 0.2 | 24.0 | 4.2 | 4.8 | 0 | ||
| GZD6004-FG | 6.0 | 0.4 | 24.0 | 4.2 | 4.8 | |||
●标准库存Stock需预定Available upon Order
精密仿形加工刀片 Precision Profiling Inserts
订货号Ordering CodeGZD3015-OR | 尺寸Dimension (mm) | 涂层硬质合金Coated | |||||
| CW | RE | L | W1 | S | GS3115 | ||
| 3.0 | 1.5 | 21.0 | 2.3 | 4.6 | |||
| GZD4020-OR | 4.0 | 2.0 | 24.0 | 3.3 | 4.8 | ||
| GZD5025-OR | 5.0 | 2.5 | 24.0 | 3.3 | 4.8 | O | |
| GZD6030-OR | 6.0 | 3.0 | 24.0 | 4.2 | 4.8 | O | |
●标准库存Stock 需预定Available upon Order
切断切槽刀片 Parting and Grooving Inserts
GB
精密切槽加工刀片 Precision Grooving Inserts
订货号Ordering CodeGB3050R-005 | 尺寸Dimension (mm) | 涂层硬质合金Coated | ||||||
| CW | CDX | RE | IC | W1 | D1 | GA4230 | ||
| 0.50 | 1.0 | 0.05 | 9.525 | 3.18 | 4.4 | |||
| GB3075R-010 | 0.75 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | ● | |
| GB3080R-005 | 0.80 | 2.0 | 0.05 | 9.525 | 3.18 | 4.4 | O | |
| GB3095R-010 | 0.95 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3100R-005 | 1.00 | 2.0 | 0.05 | 9.525 | 3.18 | 4.4 | ● | |
| GB3100R-010 | 1.00 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3120R-010 | 1.20 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3120R-020 | 1.20 | 2.0 | 0.2 | 9.525 | 3.18 | 4.4 | O | |
| GB3125R-010 | 1.25 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | ● | |
| GB3140R-010 | 1.40 | 2.0 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3140R-020 | 1.40 | 2.0 | 0.2 | 9.525 | 3.18 | 4.4 | 0 | |
| GB3140L-020 | 1.40 | 2.0 | 0.2 | 9.525 | 3.18 | 4.4 | ● | |
●标准库存Stock 需预定Available upon Order
切断切槽刀片 Parting and Grooving Inserts
GB
精密切槽加工刀片 Precision Grooving Inserts
订货号Ordering CodeGB3150R-010 | 尺寸Dimension (mm) | 涂层硬质合金Coated | ||||||
| CW | CDX | RE | IC | W1 | D1 | GA4230 | ||
| 1.50 | 2.0 | 0.1 | 9.525 3.18 | 4.4 | 0 | |||
| GB3150R-020 | 1.50 | 2.0 | 0.2 | 9.525 | 3.18 | 4.4 | ● | |
| GB3150L-020 | 1.50 | 2.0 | 0.2 | 9.525 | 3.18 | 4.4 | ||
| GB3200R-010 | 2.00 | 2.5 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3200R-020 | 2.00 | 2.5 | 0.2 | 9.525 | 3.18 | 4.4 | 0 | |
| GB3200L-020 | 2.00 | 2.5 | 0.2 | 9.525 | 3.18 | 4.4 | O | |
| GB3250R-010 | 2.50 | 2.5 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3250L-010 | 2.50 | 2.5 | 0.1 | 9.525 | 3.18 | 4.4 | O | |
| GB3250L-020 | 2.50 | 2.5 | 0.2 | 9.525 | 3.18 | 4.4 | ● | |
| GB3300R-020 | 3.00 | 2.5 | 0.2 | 9.525 | 3.18 | 4.4 | O | |
| 3.00 | 2.5 | 0.2 | 9.525 3.18 | 4.4 O | ||||
●标准库存Stock需预定Available upon Order
切断切槽刀片 Parting and Grooving Inserts
GB
精密切槽加工刀片 Precision Grooving Inserts
| 订货号 Ordering Code | 尺寸 Dimension (mm) | 涂层硬质合金 Coated | ||||||
| CW | CDX | RE | IC | W1 | D1 | GA4230 | ||
 | GB4125R-020 | 1.25 | 2.0 | 0.2 | 12.7 | 4.76 | 5.5 | 0 |
| GB4150R-010 | 1.50 | 3.5 | 0.1 | 12.7 | 4.76 | 5.5 | ● | |
| GB4150R-020 | 1.50 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | ● | |
| GB4150L-020 | 1.50 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | O | |
| GB4175R-020 | 1.75 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | O | |
| GB4185R-020 | 1.85 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | O | |
| GB4200R-020 | 2.00 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | ||
| GB4200L-020 | 2.00 | 3.5 | 0.2 | 12.7 | 4.76 | 5.5 | ||
| GB4200R-030 | 2.00 | 3.5 | 0.3 | 12.7 | 4.76 | 5.5 | ||
| GB4210R-050 | 2.10 | 4.0 | 0.5 | 12.7 | 4.76 | 5.5 | O | |
| GB4220R-030 | 2.20 | 4.0 | 0.3 | 12.7 | 4.76 | 5.5 | ||
| GB4250R-030 | 2.50 | 4.0 4.0 | 0.3 0.3 | 12.7 | 4.76 | 5.5 | O | |
| GB4250L-030 | 2.50 2.65 | 12.7 | 4.76 | 5.5 | O | |||
| GB4265R-030 | 4.0 | 0.3 | 12.7 | 4.76 | 5.5 | O | ||
| GB4280R-030 | 2.80 | 5.0 | 0.3 | 12.7 | 4.76 | 5.5 | O | |
| GB4300R-030 | 3.00 | 4.0 | 0.3 | 12.7 | 4.76 | 5.5 | ● | |
| GB4300L-030 | 3.00 | 4.0 | 0.3 | 12.7 | 4.76 | 5.5 | ● | |
| GB4350R-030 | 3.50 | 5.0 | 0.3 | 12.7 | 4.76 | 5.5 | O | |
| GB4400R-040 | 4.00 | 5.0 | 0.4 | 12.7 | 4.76 | 5.5 | O | |
| GB4400L-040 | 4.00 | 5.0 | 0.4 | 12.7 | 4.76 | 5.5 | O | |
| GB4430R-040 | 4.30 | 5.0 | 0.4 | 12.7 | 4.76 | 5.5 | O | |
●标准库存Stock 需预定Available upon Order
精密切槽加工刀片 Precision Grooving Insert
切断切槽刀片 Parting and Grooving Inserts<br>GBR
订货号Ordering Code | 尺寸Dimension (mm) | 涂层硬质合金Coated | ||||||
| CW | CDX | RE | IC | W1 | D1 | GA4230 | ||
| GBR4100R-050 | 1.00 | 2.0 | 0.5 | 12.7 | 4.76 | 5.5 | 0 | |
| GBR4100L-050 | 1.00 | 2.0 | 0.5 | 12.7 | 4.76 | 5.5 | O | |
| GBR4150R-075 | 1.50 | 3.5 | 0.75 | 12.7 | 4.76 | 5.5 | ● | |
| GBR4150L-075 | 1.50 | 3.5 | 0.75 | 12.7 | 4.76 | 5.5 | O | |
| GBR4200R-100 | 2.00 | 3.5 | 1.0 | 12.7 | 4.76 | 5.5 | O | |
| GBR4200L-100 | 2.00 | 3.5 | 1.0 | 12.7 | 4.76 | 5.5 | O | |
| GBR4250R-125 | 2.50 | 4.0 | 1.25 | 12.7 | 4.76 | 5.5 | 0 | |
| GBR4250L-125 | 2.50 | 4.0 | 1.25 | 12.7 | 4.76 | 5.5 | 0 | |
| GBR4300R-150 | 3.00 | 4.0 | 1.5 | 12.7 | 4.76 | 5.5 | 0 | |
| GBR4300L-150 | 3.00 | 4.0 | 1.5 | 12.7 | 4.76 | 5.5 | 0 | |
| GBR4400R-200 | 4.00 | 5.0 | 2.0 | 12.7 | 4.76 | 5.5 | O | |
| GBR4400L-200 | 4.00 | 5.0 | 2.0 | 12.7 | 4.76 | 5.5 | O | |
●标准库存Stock需预定Available upon Order
GZ系列GZ Series
外圆切断切槽刀杆 External Holders for Parting and Grooving
图示为右手 The Picture is Right Hand Holder
| 订货号Ordering Code | 尺寸(mm)Dimension (mm) | 匹配刀片 | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| W | CDX | H=HF | B | LF | WF | Insert | C | R | L | ||
| GZER/L2020-3T20 | 3.0 | 20 | 20 | 20 | 125 | 21 | GZD30… | SCAM050200H | TH40LH | ● | ● |
| GZER/L2525-3T20 | 3.0 | 20 | 25 | 25 | 150 | 26 | GZD30… | SCAM060200H | TH50LH | ● | ● |
| GZER/L3225-3T20 | 3.0 | 20 | 32 | 25 | 170 | 26 | GZD30… | SCAM060200H | TH50LH | O | O |
| GZER/L2020-4T25 | 4.0 | 25 | 20 | 20 | 125 | 21 | GZD40… | SCAM050200H | TH40LH | ● | O |
| 5.0 | 25 | 20 | 20 | 125 | 21.5 | GZD50… | ● | O | |||
| GZER/L25254T20 | 4.0 | 20 | 25 | 25 | 150 | 26 | GZD40… | SCAM050200H | ● | ||
| 5.0 | 20 | 25 | 25 | 150 | 26.5 | GZD50… | ● | ||||
| GZER/L2525-4T25 | 4.0 | 25 | 25 | 25 | 150 | 26 | GZD40… | SCAM060200H | ● | ||
| 5.0 | 25 | 25 | 25 | 150 | 26.5 | GZD50 | TH50LH | ● | |||
| GZER/L3225-4T25 | 4.0 | 25 | 32 | 25 | 170 | 26 | GZD40… | SCAM060200H | ● | ● | |
| 5.0 | 25 | 32 | 25 | 170 | 26.5 | GZD50… | TH50LH | ● | |||
| GZER/L2525-6T32 | 6.0 | 32 | 25 | 25 | 150 | 26 | GZD60… | SCAM060300H | TH50LH | ● | ● |
| GZER/L3225-6T32 6.0 | 32 | 32 25 170 26 GZD60… | SCAM060300H | TH50LH | O | O | |||||
备注：SCAM060200H代表M6X20 Remark: SCAM060200H is meaning of M6X20
●标准库存Stock需预定Available upon Order
●标准库存Stock需预定Available upon Order
GB系列GB Series
外圆切槽刀杆 External Holders for Grooving
图示为右手 The Picture is Right Hand Holder
| 订货号Ordering Code | 尺寸(mm)Dimension (mm) | 匹配刀片Insert | 螺钉Screw | 扳手Wrench | 库存Stock | ||||||
| H=HF | B | LF | WF | A | CDX |  | R | L | |||
| GBER/L2020K3 | 20 | 20 | 125 | 25 | 一 | 2.5 | GB3… | SI60M 035120-05310 | TT15PH | ● | O |
| GBER/L2525M3 | 25 | 25 | 150 | 30 | 一 | 2.5 | GB3… | SI60M 035120-05310 | TT15PH | ● | ● |
| GBER/L2020K4-15 | 20 | 20 | 125 | 25 | 1.0 | 4.0 | GB4…(1.0≤W<2.5) | SI60M 050120-07217 | TT20PH | ● | ● |
| GBER/L2525M4-15 | 25 | 25 | 150 | 30 | 1.0 | 4.0 | GB4…(1.0≤W<2.5) | SI60M 050120-07217 | TT20PH | ||
| GBER/L2020K4-25 | 20 | 20 | 125 | 25 | 2.0 | 4.5 | GB4…(2.5≤W<3.3) | SI60M 050120-07217 | TT20PH | O | |
| GBER/L2525M4-25 | 25 | 25 | 150 | 30 | 2.0 | 4.5 | GB4…(2.5≤W<3.3) | SI60M 050120-07217 | TT20PH | O | O |
| GBER/L2020K4-35 | 20 | 20 | 125 | 25 | 3.0 | 5.5 | GB4…(3.3≤W<4.8) | SI60M 050120-07217 | TT20PH | O | O |
| GBER/L2525M4-35 | 25 | 25 | 150 | 30 | 3.0 | 5.5 | GB4…(3.3≤W<4.8) | SI60M 050120-07217 | TT20PH | O | |
备注：SI60M035120…代表M3.5X12Remark: SI60M 035120… stands for M3.5X12
●标准库存Stock 需预定Available upon Order
●标准库存Stock 需预定Available upon Order
GB系列GB Series
内孔切槽刀杆
nternal Bars for Grooving
图示为右手The Picture is Right Hand Holder
| 订货号 Ordering Code | 尺寸(mm) Dimension (mm) | 匹配刀片 Insert | 螺钉 Screw | 扳手 Wrench | 库存 | Stock | |||||
| DMIN1 | DCON | H | LF | WF | CDX | 0 | R | L | |||
| GBIR/L2620Q3 | 26 | 20 | 18 | 180 | 13 | 3 | GB3… | SI60M035120-05310 | TT15PH | O | |
| GBIR/L3525R4 | 35 | 25 | 23 | 200 | 17.5 | 4.5 | GB4… | SI60M 050120-07217 | TT20PH | ||
备注：SI60M 035120…代表M3.5X12 Remark: SI60M 035120…is meaning of M3.5X12
●标准库存Stock需预定Available upon Order
●标准库存Stock需预定Available upon Order
G-NOTCH系列刀片型号表示规则
G-NOTCH系列切槽刀片型号表示规则
G-NOTCH Series Inserts Identification System
G-NOTCH Series Grooving Inserts Identification System
G N G P 3 M150 R
①】
【②】
③
④
【⑤】
【6】
0】
①公司代号
Company Mark
G=GESAC③刀片类型Insert styleG=切槽
G=GroovingR=圆头
R=Full Radius
②刀片型号 Type of Insert N=Notch
④附加信息
Additional Information
P=正向前角
P=Positive
□=无前角
□=Fla
公制：M150=1.5mmMetric:M150=1.5mm英制：125=0.125inchInch:125=0.125inch
⑦刀片方向
Hand of InsertR=右手
R=Right HandL=左手
L=Left Hand
| ⑤刀片规格Insert Size | ||
| mm | inch | |
| 2 | 3.81 | .150 |
| 3 | 4.95 | .195 |
G-Notch系列刀片型号表示规则G-Notch系列螺纹刀片型号表示规则
G-Notch Series Inserts Identification System G-Notch Series Threading Inserts Identification System
| ⑤刀片规格Insert Size | ||
| mm | inch | |
| 2 | 3.81 | .150 |
| 3 | 4.95 | .195 |
| ⑦刀片规格Right Hand | ||
| mm | inch | |
| 2 | 3.81 | .150 |
| 3 | 4.95 | .195 |
| M | ||
G-Notch系列刀杆型号表示规则G-Notch系列外圆刀杆型号表示规则
G-Notch Holder Identification System G-Notch External Holder Identification System
G N S R 2525 M 3
②
③
④
[⑤]
6
⑦】
①公司代号
Company Mark
G=GESAC
③刀片装夹位置
Insert Mounting
Location
S=侧装
S=Side
②夹紧方式
Clamping System
N=Notch
| 宽Windth | 高Height |
| 12 | 12 |
| 16 | 16 |
| 20 | 20 |
| 25 | 25 |
| 32 | 32 |
| ⑥刀柄长度Shank length | |
| D | 60 |
| E | 70 |
| F | 80 |
| H | 100 |
| K | 125 |
| M | 150 |
| P | 170 |
| Q | 180 |
| R | 200 |
④刀具方向 Hand of Tool L=左手 L=Left Hand
R=右手 R=Right Hand
G-Notch系列刀杆型号表示规则G-Notch系列内孔刀杆型号表示规则G-Notch Holder Identification SystemG-Notch External Holder Identification System
G N A R 25 M 3
①】
【②]
③
④
⑤
6
【0】
①公司代号
Company Mark
G=GESAC
③刀杆类型
Holder Type
A=带内冷孔的钢制刀杆
A=Steel With Coolant
S=不带内冷孔的钢制刀杆
S=Steel without Coolant
⑤刀柄尺寸 Shank Size
| 宽 | 高 |
| 12 | 12 |
| 16 | 16 |
| 20 | 20 |
| 25 | 25 |
| 32 | 32 |
⑦刀片规格 Right Hand
②夹紧方式
Clamping System
N=Notch
| mm | inch | |
| 2 | 3.81 | .150 |
| 3 | 4.95 | .195 |
④刀具方向 Hand of Tool L=左手 L=Left hand
R=右手 R=Right hand
| ⑥刀柄长度Shank length | |
| D | 60 |
| E | 70 |
| F | 80 |
| H | 100 |
| K | 125 |
| M | 150 |
| P | 170 |
| Q | 180 |
| R | 200 |
G-Notch系列刀片一览表Overview of G-Notch Series Inserts
| 应用Application | 类型Style | 外形Shape | 宽度/螺距Width/Pitch | 页码Page |
| 精密切槽Precision Grooving | GNGP |  | 1.00-3.50(mm) | P67 |
| 精密仿形Precision Profiling | GNR |  | 2.00-3.18(mm) | P69 |
| 螺纹加工Threading | GNTP |  | 0.70-5.00(mm)36-5(TPI) | P69 |
G-Notch系列刀片G-Notch Series Insert
GNGP
精密切槽刀片(正前角） Precision Grooving Inserts (positive rake angle)
订货号Ordering code | ||||||||||
| 尺寸(mm)Dimension (mm) | 刀片规格Insert | 涂层硬质合金Coating | ||||||||
| CW±0.025 | RE | CDX | S | W1 | D | Size | GM3225 | GS3115 | ||
| GNGP2M100L | 1.00 | 0.09 | 1.27 | 5.56 | 3.81 | 8.74 | 2 | O | ● | |
| GNGP2M100R | 1.00 | 0.09 | 1.27 | 5.56 | 3.81 | 8.74 | 2 | O | ● | |
| GNGP2047L | 1.19 | 0.09 | 1.27 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2047R | 1.19 | 0.09 | 1.27 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2M150L | 1.50 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | ● | |
| GNGP2M150R | 1.50 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | ||
| GNGP2062L | 1.57 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2062R | 1.57 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | ● | O | |
| GNGP2M170L | 1.70 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | 0 | |
| GNGP2M170R | 1.70 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2070L | 1.78 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | 0 | |
| GNGP2078L | 1.98 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2078R | 1.98 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | ● | O | |
| GNGP2M200L | 2.00 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | |||
| GNGP2M200R | 2.00 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | ● | |
| GNGP2M220L | 2.20 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2M220R | 2.20 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2094L | 2.38 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2094R | 2.38 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | ● | 0 | |
| GNGP2M250L | 2.50 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | ● | |
| GNGP2M250R | 2.50 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2125L | 3.18 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | O | O | |
| GNGP2125R | 3.18 | 0.19 | 2.79 | 5.56 | 3.81 | 8.74 | 2 | ● | O | |
| GNGP3031L | 0.79 | 0.09 | 1.27 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3031R | 0.79 | 0.09 | 1.27 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M100L | 1.00 | 0.19 | 1.91 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M100R | 1.00 | 0.19 | 1.91 | 8.74 | 4.95 | 16.1 | 3 | O | 0 | |
| GNGP3047L | 1.19 | 0.19 | 1.91 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| 1.19 0.19 1.91 | 8.74 4.95 | 16.1 | 3 | O | O | |||||
●标准库存Stock 需预定Available upon Order
G-Notch系列刀片G-Notch Series Insert
GNGP
精密切槽刀片(正前角) Precision Grooving Inserts (positive rake angle)
| 订货号Ordering code | 尺寸(mm)Dimension (mm) | 刀片规格InsertSize | 涂层硬质合金Coating | |||||||
| CW | RE | CDX | S | W1 | D | GM3225 | GS3115 | |||
 | GNGP3M150L | 1.50 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | 0 |
| GNGP3M150R | 1.50 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | ● | |
| GNGP3062L | 1.58 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3062R | 1.58 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3070L | 1.78 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3078L | 1.98 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3078R | 1.98 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3M200L | 2.00 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M200R | 2.00 | 0.19 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3094L | 2.39 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3094R | 2.39 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3M250L | 2.50 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M250R | 2.50 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M300L | 3.00 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M300R | 3.00 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3125L | 3.18 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3125R | 3.18 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | ● | O | |
| GNGP3M350L | 3.50 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
| GNGP3M350R | 3.50 | 0.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
●标准库存Stock 需预定Available upon Order
G-Notch系列刀片G-Notch Series
GNR
切槽圆头刀片(0°前角) Full Radius Inserts(0°rakeangle)
| 订货号Ordering code | 尺寸Dimension(mm) | 刀片规格Insert | 涂层硬质合金Coated | |||||||
| CW | RE | CDX | S | W1 | D | Size | GM3225 | GS3115 | ||
 | GNR3M100R | 2.00 | 1.00 | 2.39 | 8.74 | 4.95 | 16.1 | 3 | 0 | O |
| GNR3M150R | 3.00 | 1.50 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | 0 | O | |
| GNR3047L | 2.39 | 1.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | 0 | 0 | |
| GNR3047R | 2.39 | 1.19 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | 0 | 0 | |
| GNR3062R | 3.18 | 1.59 | 3.81 | 8.74 | 4.95 | 16.1 | 3 | O | O | |
●标准库存Stock 需预定Available upon Order
螺纹刀片 Threading Inserts
GNTP
60°通用螺纹刀片,带前角
60°Partial Profile Threading Inserts With
| 订货号Ordering Code | 螺距Pitch | 尺寸(mm)Dimension(mm) | 刀片规格 | 涂层硬质合金Coated | ||||||
| 外牙Externalmm | 内牙Internalmm | 外牙ExternalTPI | 内牙InternalTPI | RE | E | InsertSize | GM3225 | GS3115 | ||
 | GNTP2L | 0.70-3.00 1.25-3.50 | 8-36 | 7-20 | 0.10 | 1.91 | 2 | O | O | |
| GNTP2R | 0.70-3.001 | .25-3.50 | 8-36 | 7-20 | 0.10 | 1.91 | 2 | O | O | |
| GNTP3L | 1.25-4.002 | .00-5.00 | 4-20 | 5-12 | 0.17 | 2.49 | 3 | O | O | |
| GNTP3R | 1.25-4.002.00-5.00 | 4-20 | 5-12 | 0.17 | 2.49 | 3 | ● | O | ||
| GNTP3004R | 1.25-4.002 | .00-5.00 | 5-36 | 5-12 | 0.10 | 2.49 | 3 | O | O | |
●标准库存Stock需预定Available upon Order
外圆刀杆External Holder
GNS
图示为右手The Picture is Right Hand Holder
| 订货号Ordering code | 尺寸(mm)Dimension (mm) | 匹配万片Insert | 螺钉Screw | 压板Clamp | 扳手Wrench | 库存Stock | |||||
| H | B | WF | LF | OHX | CDX | o |  | C | |||
| GNSR1616H2 | 16 | 16 | 20 | 100 | 19 | 3.5 | GN.2R | SCAM040120H | CAN02RH | TH30LH | |
| GNSR2020K2 | 20 | 20 | 25 | 125 | 19 | 3.5 | GN.2R | SCAM040120H | CAN02RH | TH30LH | O |
| GNSR2525M2 | 25 | 25 | 32 | 150 | 19 | 3.5 | GN.2R | SCAM040120H | CAN02RH | TH30LH | O |
| GNSR2020K3 | 20 | 20 | 25 | 125 | 32 | 5.3 | GN.3R | SCAM050200H | CAN03RH | TH40LH | ● |
| GNSR2525M3 | 25 | 25 | 32 | 150 | 32 | 5.3 | GN.3R | SCAM050200H | CAN03RH | TH40LH | ● |
| GNSL1616H2 | 16 | 16 | 20 | 100 | 19 | 3.5 | GN.2L | SCAM040120H | CAN02LH | TH30LH | O |
| GNSL2020K2 | 20 | 20 | 25 | 125 | 19 | 3.5 | GN.2L | SCAM040120H | CAN02LH | TH30LH | O |
| GNSL2525M2 | 25 | 25 | 32 | 150 | 19 | 3.5 | GN.2L | SCAM040120H | CAN02LH | TH30LH | O |
| GNSL2020K3 | 25 | 20 | 25 | 125 | 32 | 5.3 | GN.3L | SCAM050200H | CAN03LH | TH40LH | O |
| GNSL2525M3 | 25 | 25 | 32 | 150 | 32 | 5.3 | GN.3L | SCAM050200H | CAN03LH | TH40LH | ● |
●标准库存Stock 需预定Available upon Order
内孔刀杆Internal Holder
图示为右手The Picture is Right Hand Holder
| 订货号Ordering code | 尺寸(mm)Dimension (mm) | 匹配 | 螺钉Screw | 压板Clamp | 扳手Wrench | 库存Stock | ||||
| DCON | DMIN1 | LF | WF | CS | 万片Insert |  |  |  | ||
| GNAR20Q2 20 | 26 | 180 13 | 1/8-27 NPTGN.2L CAN02LH SCAM040120H TH30LH | O | ||||||
| GNAR25R2 | 25 | 34 | 200 | 17 | 1/4-18 NPT | GN.2L | CAN02LH | SCAM040120H | TH30LH | O |
| GNAR25R3 | 25 | 34 | 200 | 17 | 1/4-18 NPT | GN.3L | CAN03LH | SCAM050200H | TH40LH | O |
| GNAL20Q2 | 20 | 26 | 180 | 13 | 1/8-27 NPT | GN.2R | CAN02RH | SCAM040120H | TH30LH | ● |
| GNAL25R2 | 25 | 34 | 200 | 17 | 1/4-18 NPT | GN.2R | CAN02RH | SCAM040120H | TH30LH | O |
| GNAL25R3 | 25 | 34 | 200 | 17 | 1/4-18 NPT | GN.3R | CAN03RH | SCAM050200H | TH40LH | O |
注意：左手内圆刀杆使用右手刀片，右手内圆刀杆使用左手刀片。
Note: Left hand bars use right hand inserts, Right hand bars use left hand inserts
●标准库存Stock需预定Available upon Order
Note: Left hand bars use right hand inserts, Right hand bars use left hand inserts
●标准库存Stock需预定Available upon Order
推荐切削参数 Recommended Cutting Data
进给推荐值 Recommend feed
| 切宽 WidthW(mm) | 进给量 Feedf(mm/r) |
| 0.79-1.50 | 0.08 (0.03-0.12) |
| 1.50-2.50 | 0.10 (0.04-0.16) |
| 2.50-3.50 | 0.12 (0.05-0.20) |
| 3.50-4.50 | 0.14 (0.05-0.25) |
切削速度推荐值
Recommend cutting speed
| ISO | 工件材料Workpiece Material | 硬度 Hardness(HB) | 切削速度 Cutting SpeedVc (m/min) | |
| GM3225 | GS3115 | |||
| 低碳钢Low Carbon Steel | 80-170 | 110 110(70-180) (70-180) | ||
 | 高碳钢High Carbon Steel | 170-250 | 110(70-160) | 110(70-160) |
| 低合金钢Low-alloy Steel | 140-260 | 110(60-160) | 110(60-160) | |
| 高合金钢High-alloy Steel | 180-300 | 110(60-160) | 110(60-160) | |
| M | 铁素体/马氏体Ferritic/Martensitic | 150-270 | 100(40-180) | 100(40-180) |
| 奥氏体Austenitic | 150-270 | 100(40-180) | 100(40-180) | |
| K | 可锻铸铁Malleable Cast Iron | 150-230 | 180(70-300) | 180(70-300) |
| 灰口铸铁Gray Cast Iron | 150-230 | 180(70-300) | 180(70-300) | |
| 球墨铸铁Nodular Cast Iron | 160-260 | 160(60-300) | 160(60-300) | |
| 30S (20-50)钛合金4040130-400Titanium Alloys (20-60) (20-60) | ||||
| (20-50) | ||||
铣削 Milling
ISO铣削刀片型号表示规则
ISO Milling Indexable Inserts Identification System
| 代号Symbol | 形状Shape | 刀尖角(度)Corner Angle | 图形Figure | ||
| H | 正六边形Hexagon | 120° | |||
| 0 | 正八边形Octagon | 135° | O | ||
| P | 正五边形Pentagon | 108° | |||
| S | 正方形Square | 90° | □ | ||
| T | 正三角形Triangle | 60° | △ | ||
| C | 80° | ||||
| D | 55° | ||||
| E | 菱形 | 75° | |||
| F | Rhombic | 50° | |||
| M | 86° | ||||
| V | 35° | ||||
| W | 六边形Trigon | 80° | △ | ||
| L | 长方形Rectangle | 90° | |||
| A | 平行四边形Parellelogram | 85°82°55° | □ | ||
| B | |||||
| K | |||||
| R | 圆形Round | O | |||
| ①形状代号Shape Symbol | |||||
| 代号Symbol | 后角(度)Relief Angle |
| A | 3° |
| B | 5° |
| C | 7° |
| D | 15° |
| E | 20° |
| F | 25° |
| G | 30° |
| N | 0° |
| P | 11° |
| 0 | 其他Others |
①
D
②
| 代号Symbol | 公差Tolerance (mm) | 公差Tolerance(inch) | ||||
| 刀尖高CornerHeight(m) | 厚度Thickness(s) | 内切圆I.C.Size(∅d) | 刀尖高CornerHeight(m) | 厚度Thickness(s) | 内切圆I.C.Size(∅d) | |
| A | ±0.005 | ±0.025 | ±0.025 | ±0.0002 | ±0.001 | ±0.001 |
| F | ±0.005 | ±0.025 | ±0.013 | ±0.0002 | ±0.001 | ±0.0005 |
| C | ±0.013 | ±0.025 | ±0.025 | ±0.0005 | ±0.001 | ±0.001 |
| H | ±0.013 | ±0.025 | ±0.013 | ±0.0005 | ±0.001 | ±0.0005 |
| E | ±0.025 | ±0.025 | ±0.025 | ±0.001 | ±0.001 | ±0.001 |
| G | ±0.025 | ±0.13 | ±0.025 | ±0.001 | ±0.005 | ±0.001 |
| J | ±0.005 | ±0.025 | ±0.05~±0.13 | ±0.0002 | ±0.001 | ±0.002~±0.005 |
| K | ±0.013 | ±0.025 | ±0.05~±0.13 | ±0.0005 | ±0.001 | ±0.002~±0.005 |
| L | ±0.025 | ±0.025 | ±0.05~±0.13 | ±0.001 | ±0.001 | ±0.002~±0.005 |
| M | ±0.08~±0.18 | ±0.13 | ±0.05~±0.13 | ±0.003~±0.007 | ±0.005 | ±0.002~±0.005 |
| N | ±0.08~±0.18 | ±0.025 | ±0.05~±0.13 | ±0.003~±0.007 | ±0.001 | ±0.002~±0.005 |
| U | ±0.13~±0.38 | ±0.13 | ±0.08~±0.25 | ±0.005~±0.015 | ±0.005 | ±0.003~±0.01 |
| ④断屑槽·孔代号Chipbreaker /Hole Symbol | |||||
| 代号Symbol | 有无孔Hole | 孔的形状Hole Shape | 断屑槽Chipbreaker | 形状Shape | |
| N | 无With-out | 无Without | |||
| R | 单面Single-sided | QO | |||
| F | 双面Double-sided | ||||
| A | 圆柱孔With Hole | 无Without | 日日 | ||
| M | 单面Single-sided | ||||
| G | 双面Double-sided | ||||
| W | 部分圆柱孔单面40°~60°With hole andone counter-sink 40°~60° | 无Without | |||
| T | 单面Single-sided | ||||
| Q | 有With | 部分圆柱孔双面40°~60°With hole andtwo counter-sinks 40°~60° | 无Without | 日 | |
| U | 双面Double-sided | ||||
| B | 部分圆柱孔单面70°~90° | 无Without | |||
| H | With hole andone counter-sink 70°~90° | 单面Single-sided | |||
| C | 部分圆柱孔双面70°~90° | 无Without | |||
| J | With hole andtwo counter-sinks 70°~90° | 双面Double-sided | |||
| X | |||||
③
[④】
12
12
⑤
⑤ISO切削刃长度代号 Cutting Edge Length Symbol(ISO)(mm)
| T V | S | 回 | D | K | 内切圆I.C.Size(mm) | |||||||||||
| 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | 代号Symbol | 尺寸Length | |
| 03 | 3.97 | 03 | 4.0 | 06 | 6.9 | 4 | 4.8 | 3.97 | ||||||||
| 04 | 4.76 | 04 | 4.8 | 08 | 8.2 | 5 | 5.8 | 4.76 | ||||||||
| 05 | 5 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 5 |
| 05 | 5.56 | 05 | 5.6 | 03 | 3.8 | 09 | 9.6 | 6 | 6.8 | 5.56 | ||||||
| 06 | 6 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 6 |
| 06 | 6.35 | 06 | 6.5 | 04 | 4.3 | 11 | 11 | 7 | 7.8 | 11 | 11.2 | 6.35 | ||||
| 07 | 7.94 | 08 | 8.1 | 05 | 5.4 | 13 | 13.8 | 9 | 9.7 | 7.94 | ||||||
| 08 | 8 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 8 |
| 09 | 9.525 | 09 | 9.525 | 09 | 9.7 | 06 | 6.5 | 16 | 16.5 | 11 | 11.6 | 16 | 16.6 | 16 | 19.7 | 9.525 |
| 10 | 10 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 10 |
| 12 | 12 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 12 |
| 12 | 12.7 | 12 | 12.7 | 12 | 12.9 | 08 | 8.7 | 22 | 22 | 15 | 15.5 | 22 | 22.1 | 12.7 | ||
| 15 | 15.875 | 15 | 15.875 | 16 | 16.1 | 10 | 10.9 | 27 | 27.5 | 19 | 19.4 | 15.875 | ||||
| 16 | 16 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 16 |
| 19 | 19.05 | 19 | 19.05 | 19 | 19.3 | 13 | 13 | 33 | 33 | 23 | 23.3 | 19.05 | ||||
| 20 | 20 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 20 |
| 22 | 22.225 | 22 | 22.6 | 38 | 38.5 | 27 | 27.1 | 22.225 | ||||||||
| 25 | 25 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 25 |
| 25 | 25.4 | 25 | 25.4 | 25 | 25.8 | 44 | 44 | 31 | 31 | 25.4 | ||||||
| 31 | 31.75 | 31 | 31.75 | 32 | 32.2 | 55 | 55 | 38 | 38.8 | 31.75 | ||||||
| 31 | 32 | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | -- | 32 |
Insert Shape:H,O,P,S,T,C,E,M,W,R
适用刀片形状：H,O,P,S,T,C,E,M,W,R
| 标准内切圆I.C.Size(mm) | 内切圆(∅d)的公差Tolerance ofI.C.Size(Ød)(mm) | 刀尖高(m)的公差(mm)Tolerance of CornerHeight(m)(mm) | 标准内切圆(inch)I.C.Size(inch) | 内切圆(∅d)的公差(inch)Tolerance ofI.C.Size(Ød)(mm) | 刀尖高(m)的公差(inch)olerance of CornerHeight(m)(mm) | ||||
| J,K,L,M,N(级) | U(级) | M,N(级) | U(级) | ClassJ,K,L,M,N | Class U | ClassJ,K,L,M,N | Class U | ||
| 6.35 | ±0.05 | ±0.08 | ±0.08 | ±0.13 | 0.250 | ±0.002 | ±0.003 | ±0.003 | ±0.005 |
| 9.525 | 0.375 | ||||||||
| 12.7 | ±0.08 | ±0.13 | ±0.13 | ±0.2 | 0.500 | ±0.003 | ±0.005 | ±0.005 | ±0.008 |
| 15.875 | ±0.1 | ±0.18 | ±0.15 | ±0.27 | 0.625 | ±0.004 | ±0.007 | ±0.006 | ±0.011 |
| 19.05 | 0.750 | ||||||||
| 25.4 | ±0.13 | ±0.25 | ±0.18 | ±0.38 | 1.000 | ±0.005 | ±0.010 | ±0.007 | ±0.015 |
| 31.75 | ±0.15 | ±0.25 | ±0.2 | ±0.38 | 1.250 | ±0.006 | ±0.010 | ±0.008 | ±0.015 |
| 32 | 1.260 | ||||||||
| 内切圆直径Inscribed Circle Size | 内切圆的公差Tolerance ofI.C.Size | 刀尖高的公差Tolerance of Corner Height | |||
| mm | inch | mm | inch | mm | inch |
| 6.35 | 0.250 | ±0.05 | ±0.002 | ±0.11 | ±0.004 |
| 9.525 | 0.375 | ±0.05 | ±0.002 | ±0.11 | ±0.004 |
| 12.7 | 0.500 | ±0.08 | ±0.003 | ±0.15 | ±0.006 |
| 15.875 | 0.625 | ±0.10 | ±0.004 | ±0.18 | ±0.007 |
| 19.05 | 0.750 | ±0.10 | ±0.004 | ±0.18 | ±0.007 |
| 适用刀片形状：VInsert Shape: V | |||||
| 内切圆∅dInscribed Circle Size | 内切圆的公差Tolerance of I.C.Size | 刀尖高的公差Tolerance of Corner Height | |||
| mm | inch | mm | inch | mm | inch |
| 6.35 | 0.250 | ±0.05 | ±0.002 | ±0.15 | ±0.006 |
| 9.525 | 0.375 | ±0.05 | ±0.002 | ±0.15 | ±0.006 |
| 12.7 | 0.500 | ±0.08 | ±0.003 | ±0.20 | ±0.008 |
| 15.875 | 0.625 | ±0.10 | ±0.004 | ±0.27 | ±0.011 |
| 19.05 | 0.750 | ±0.10 | ±0.004 | ±0.27 | ±0.011 |
| 代号Symbol | 厚度Thickness(mm) |
| 01 | 1.59 |
| T1 | 1.98 |
| 02 | 2.38 |
| T2 | 2.78 |
| 03 | 3.18 |
| T3 | 3.97 |
| 04 | 4.76 |
| 05 | 5.56 |
| 06 | 6.35 |
| 07 | 7.94 |
| 09 | 9.52 |
| ⑥厚度代号⑥Thickness Symbol | |
⑦
①
0
8
内切圆(∅d)D.Theoretical Diameter ofInscribed Circle
刀片厚度(s) M.See Fig.
刀尖高(m) S. Insert Thickness
⑦主偏角、修光刃后角及刀尖形状 Wiper Angle or Nose Radius
⑧主切削刃代号 Major Cutting Edge
| 代号Symbol | 切削刃形状Description | 形状 |
| F | 锋利刃Sharp Edge |   |
| E | 圆弧刃R-Honed | |
| T | 负倒棱角Chamfer | |
| S | 复合钝化刃Chamfer andR-Honed |
| 代号Symbol | 余偏ApproachAngle | 主偏角CuttingEdgeAngle | 代号Symbol | 修光刃后角ReliefAngleof Wiper | 代号Symbol | 刀尖圆弧半径Corner-Rε(mm) |
| A | 45° | 45° | A | 3° | MO | 圆刀片circularinserts |
| D | 30° | 60° | B | 5° | 00 | 0.03 |
| E | 15° | 75° | C | 7° | 02 | 0.2 |
| F | 5° | 85° | D | 15° | 04 | 0.4 |
| P | 0° | 90° | E | 20° | 08 | 0.8 |
| Z | 其他Others | F | 25° | 12 | 1.2 | |
| 20 | 2.0 | |||||
| 24 | 2.4 | |||||
| 28 | 2.8 | |||||
| 32 | 3.2 | |||||
| ⑨切削方向代号Direction | ||
| 代号Symbol | 切削刃形状Hand | 图示Shape |
| R | 右Right |  |
| L | 左Left |  |
| N | 无Neutral |  |
10断屑槽代号 Chipbreaker Symbol
| 代号Symbol | 工况Machining Condition |
| GL | 通用轻切削General LightingCutting |
| GM | 通用中切削General MediumCutting |
| GH | 通用重切削General HeavyCutting |
| PL | 钢材轻切削Light Cutting forSteel |
| PM | 钢材中切削Medium Cutting forSteel |
| PR | 钢材准重切削Rough Cutting forSteel |
| KM | 铸铁中切削Medium Cutting forCast Iron |
| KR | 铸铁准重切削Rough Cutting forCast Iron |
| MM | 不锈钢中切削Medium Cutting forStainless Steel |
| W* | 修光刃切削Wiper Cutting |
| NL/AL | 有色金属轻切削Lighting Cutting forNonferrous Metal |
可转位铣削刀体型号表示规则Milling Cutter Holder Identification System
MF
45
160
①】
②
③
【④
⑤
6
| ①刀具类型Milling Tool Type | ||
| 平面铣削FaceMilling | MF | 常规平面铣削General FaceMilling |
| MV | 重载平面铣削Heavy FaceMilling | |
| 方肩铣削ShoulderMilling | ME | 常规方肩铣削GeneralShoulder Milling |
| MH | 长刃方肩铣削Helical Milling | |
| 仿形铣削ProfileMilling | MP | 常规仿形铣削General ProfileMilling |
| MB | 球头仿形铣削Ball Nose Milling | |
| 快进给铣削HighFeedMilling | MK | 常规快进给铣削General HighFeed Milling |
| 槽铣SlotMilling | MS | 三面刃槽铣Side and FaceMilling |
| 倒角铣削ChamferMilling | MC | 倒角铣削Chamfer Milling |
| 其他Others | MX | 特殊铣削Special Milling |
②系列编号Series Number
③产品代次Serial Number第1代
1First第2代
2Second
45
④主偏角 Lead Angle 45=45°
⑤刀具直径 Cutting Diameters 160 160=160mm
⑥切削方向 Cutting Direction 右
R Right Hand 左
L Left Hand
09 C 40 (T) S E 13 (M)
[0】
8
0
0
①
①】
13
14
⑦齿数 No. of teeth 09 9齿
| ⑧接口类型Type of Coupling | |
| A | A型接口A Type |
| B | B型接口B Type |
| C | C型接口C Type |
| D | D型接口D Type |
| M | 螺纹接口ThreadedInterface |
| P | 直柄Straight Shank |
| W | 削平直柄Weldon Shank |
| BT | BT 型接口BT Type |
| HA | HSK-A接口HSK-A Type |
⑨接口尺寸
Coupling Size
40 40=40mm
⑩0颈部类型
Neck type 锥颈 Cone Neck
| ①刀片形状Insert Shape | |
| V | 35°菱形35°Rhombic |
| D | 55°菱形55°Rhombic |
| C | 80°菱形80°Rhombic |
| S | 正方形Square |
| T | 正三角形Triangle |
| R | 圆形Round |
| L | 长方形Rectangle |
| ②刀片后角Insert ClearanceAngle | |
| N | 0° |
| B | 5° |
| C | 7° |
| P | 11° |
| D | 15° |
| E | 20° |
| F | 25° |
| 4刀杆长度Body Length | |
| S | 短Short |
| M | 一般Normal |
| L | 长Long |
③切削刃长度Cutting Edge Length13 13=13mm系列介绍Series Introduction
方肩铣系列Shoulder Milling Series
XDHT
正型两刃铝用方肩铣XDHT刀片+MEH190刀体
●大前角设计，阻力小，切削轻快。
●正型双后角设计，提高刃口强度。
●长切削刃设计，满足大切深加工工况。
●曲线刃刃型设计，在方肩铣削时达到真正的90°台阶。
●主要用于铝合金材料的粗加工至半精加工。
Positive double edges shoulder milling for aluminum XDHT insert +MEH190 cutter holder
• Big rake angle design, ensure small cutting resistance
• Positive double clearance angle design, improve the strength of the edge
• Long cutting edge design, suitable for big cutting depth
• Curve edge design, ensure to achive 90° step in shoulder milling
● Suitable for semi-finishing and roughing of aluminum alloy
ADGT
正型两刃方肩铣ADGT刀片+MET190刀体
●空间曲线刃刃型结构设计，有效降低切削阻力。
●变刃宽结构设计，提高刀具寿命。
●钛合金材料加工的特殊专用槽型。
●主要用于钛合金材料粗加工至半精加工。
Positive two edges shoulder milling ADGT inserts+MET190 cutter holder
• The edge with spatial curve Cutting Tooldesign to decrease the cutting resistance.
● The blade geometry with variable edge width, increased tool life.
• The special dedicated geometry for machining of Ti alloy.
● Suitable for semi-finishing and roughing machining of Ti alloy.
系列介绍Series Introduction仿形铣削系列Profile Milling Series
RP/RC
正型仿形铣RP/RC刀片+MPB100/MPC100刀体
● 经济且高效。
●槽型全面，覆盖轻载到重载加工。
●RC+MPC100系列产品具有防转动系统设计，切削过程更稳定。
●可提供经济型和精密型两种刀片，满足不同客户需求。
●主要用于不锈钢和钛合金等材料粗加工至半精加工。
Positive profile milling RP/RC insert +MPB100/MPC100 cutter holder
● With economical and high efficiency
• With full range of geometry, available from light cutting to heavy cutting
RC+MPC100 is with anti rotation design, ensure stable cutting
● Economy type inserts and high precision type inserts for choice,
satisfy different customer requirement
● Suitable for semi-finish and roughing machining of stainless steel and titanium alloy
系列介绍Series Introduction
快进给铣削系列High feed milling series
SOE (M)T
正型四刃快进给SOE(M)T-SM刀片+MKT113刀体SOMT-ST刀片+MKT213刀体
●正前角加工，切削轻快，加工稳定。
●两段式切削刃设计，满足不同加工工况需求。
●带修光刃设计，在高进给加工和侧壁加工时，具有良好的加工表面质量。
●特殊表面涂层工艺，刃口表面光滑，减少积屑瘤产生。
● 主要用于钛合金材料粗加工。
Positive four edges high-feed milling for Ti alloy SOE(M)T-SM inserts +MKT113 cutter holder SOMT-ST inserts +MKT213 cutter holder
• Positive rake angle processing, cutting light, stable processing. • The cutting edge with two-stage cutting edge design, suitable for different processing conditions.
• Design with wiper , in high feed processing and side wall processing, has good processing surface quality.
• Special surface coating technology, make the edge surface smooth, and reduce the formation of debris tumor.
• Suitable for roughing machining of Ti alloy.
可转位铣削产品一览表 Indexable Milling Products List
| 类型 Type | 应用 Application | 刀片系列 Inserts Series | 刀体系列 Cutter Holder Series | 图示 Picture | 简介 Product Application |
| 方肩 铣削 Shoulder Milling |  AD10: APMX =9.0mm AD12: APMX=11.0mm AD18: APMX=16.0mm | ADGT P083 | MET190 (φ16-φ160) |    | 钛合金材料的方肩、 平面、型腔铣和槽铣 等多种加工方式。 Shoulder,face, cavity and slot milling for titanium alloy. |
 XD19: APMX =18.0mm | XDHT P091 | MEH190 (Φ25-φ125) |   | 铝合金高效方 肩铣削加工。 High efficiency shoulder milling for aluminum alloy. |
可转位铣削产品一览表 Indexable Milling Products List
| 类型 Type | 应用 Application | 刀片系列 Inserts Series | 刀体系列 Cutter Holder Series | 图示 Picture | 简介 Product Application |
| 仿形 铣削 Profile Milling |  RP08: APMX =4.0mm RP10: APMX =5.0 mm RP12: APMX =6.0 mm RP16: APMX =8.0 mm | RP P095 | MPB100 (Φ16-Φ125) |  | 不锈钢、钛合金材 料的仿形、平面、 槽铣及型腔铣削加 工。 Profile, face, slot and cavity milling for stainless steel and titanium alloy. |
 RC10: APMX =5.0 mm RC12: APMX =6.0 mm RC16: APMX =8.0 mm RC20: APMX =10.0 mm | RC P099 | MPC100 (Φ20-Φ160) |  | 不锈钢、钛合金材 料的仿形、平面、 槽铣及型腔铣削加 工。 Profile, face, slot and cavity milling for stainless steel and titanium alloy. | |
 SO09: APMX=1.2mm SO12: APMX=1.4mm | SOE(M)T P106 | MKT113 (φ25-φ125) |  | 钛合金材料的平面 和型腔铣削加工。 Face and cavity milling for titanium alloy. | |
铣削 High Feed Milling  SO09: APMX=1.1mm SO12: APMX=1.8mm | SOMT P106 | MKT213 (Φ25-φ125) |  | 钛合金材料的槽 铣、坡铣及插补铣 削加工。 Slot, slope and Interpolation milling for titanium alloy. |
