HJ TOOLS 硬质合金端铣刀介绍和使用指南 - 电子书在线预览、各类电子书在线制作-云展网平台

UC-RH4

4 flute, corner radius,long shank endmill for general machining

OrderingCode	Mill Dia. (D)	Flute Length (LC)	Corner (r)	OverallLength (L)	ShankDia. (d)	Type	Stock
UC-RH4-04002	4	11	0.2	75	4	B	.
UC-RH4-04005	4	11	0.5	75	4	B	.
UC-RH4-06005	6	16	0.5	75	6	B	.
UC-RH4-06005-100	6	16	0.5	100	6	B	.
UC-RH4-06010	6	16	1.0	75	6	B
UC-RH4-06010-100	6	16	1.0	100	6	B	.
UC-RH4-08005-75	8	20	0.5	75	8	B	.
UC-RH4-08010-75	8	20	1.0	75	8	B
UC-RH4-08005	8	20	0.5	100	8	B
UC-RH4-08010	8	20	1.0	100	8	B	.
UC-RH4-10005	10	25	0.5	100	10	B	.
UC-RH4-10010	10	25	1.0	100	10	B	.
UC-RH4-10020	10	25	2.0	100	10	B
UC-RH4-12005	12	30	0.5	100	12	B
UC-RH4-12010	12	30	1.0	100	12	B	.
UC-RH4-12020	12	30	2.0	100	12	B	.
UC-RH4-16010	16	45	1.0	100	16	B	.
UC-RH4-16020	16	45	2.0	100	16	B

Stock 0 Available UponOrder

D/mm	Tol./mm
D≤12	0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels HardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。

{ \circ } MostSuitable 0 Suitable

RecommendingCuttingPrametersP155

PAGE/050

UC-B2

2 flute, ball nose endmill for general machining

Ordering Code	Mill Dia. (D)	Ball Radius (R)	(LC)	Flute Length Overall Length (L)	Shank Dia. (d)	Type	Stock
UC-B2-01002	1	0.5	2	50	4	A	.
UC-B2-01503	1.5	0.75	3	50	4	A	.
UC-B2-02004	2	1	4	50	4	A	.
UC-B2-02505	2.5	1.25	5	50	4	A
UC-B2-03006	3	1.5	6	50	4	A
UC-B2-03507	3.5	1.75	7	50	4	A
UC-B2-04008	4	2	8	50	4	B
UC-B2-05010	5	2.5	10	50	6	A
UC-B2-06012	6	3	12	50	6	B
UC-B2-07014	7	3.5	14	60	8	A
UC-B2-08014	8	4	14	60	8	B
UC-B2-09016	9	4.5	16	75	10	A
UC-B2-10018	10	5	18	75	10	B

R/mm	Tol./mm
R≤6	0.01
R>6	-0.015

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels Hardenedsteels Hardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。

⊚ MostSuitable 0 Suitable

PAGE/051

UC-BH2

2 flute,ball nose, long shank endmill for general machining

OrderingCode	Mill Dia. (D)	Ball Radius (R)	(LC)	Flute Length OverallLength (L)	ShankDia. (d)	Type	Stock
UC-BH2-04008	4	2	8	75	4	B	.
UC-BH2-04008-100	4	2	8	100	4	B	.
UC-BH2-06012	6	3	12	75	6	B	.
UC-BH2-06012-100	6	3	12	100	6	B	.
UC-BH2-08014	8	4	14	75	8	B	.
UC-BH2-08014-100	8	4	14	100	8	B	.
UC-BH2-10018	10	5	18	100	10	B
UC-BH2-12022	12	6	22	100	12	B	.

Stock OAvailable Upon Order

R/mm	Tol./mm
R≤6	0.01
R>6	-0.015

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels Hardenedsteels Hardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	O

⑨ MostSuitable 0 Suitable

RecommendingCuttingPrametersP155

PAGE/052

UR Series

General rough machining series

I Special wave flute design,makes small chip and smooth chip exhausting

I Big helix angle + \cup groove design, increases machining stability

I High performance ultra fine substrate,together with high performance AlCrSiN coating, good heat resistance and wear resistance.Also suitable for heavy roughing

Model No	UR-S4-10025
Specification	D10C0.32575d10
Workpiecematerial	45#(180HB)
Cutting speed	5500RPM
Feed rate	600mm/min
Way of cutting	slotting
ap,ae	ap=6mm,ae=10mm
Coolant	emulsion

Workpiece quantity (pcs)

UR-S4

4 flute, square endmill for rough machining

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	Chamfer (C)	OverallLength (L)	Shank Dia. (d)	Type	Stock
UR-S4-06016	6	16	0.2	50	6	B
UR-S4-08020	8	20	0.2	60	8	B	.
UR-S4-10025	10	25	0.3	75	10	B	.
UR-S4-12030	12	30	0.3	75	12	B
UR-S4-16036	16	36	0.4	100	16	B	.
UR-S4-20045	20	45	0.5	100	20	B	.

Stock 0 Available Upon Order

D/mm	Tol./mm
D≤6	-0.03
6	-0.04
D>10	-0.05

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。		O

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrameters P156

PAGE/054

X Series

Endmill for steelhigh efficiency machining

I Suitable for wide range ofworkpiece

{ \scriptsize { 1 } } Variable groove depth design considering both tool rigidity and chip pocket, good forhigh efficient machining with big cutting depth & width

I Suitable forwide range of workpiece

{ \scriptsize { 1 } } Suitable for facing milling under smallap& big ae,side milling under big ap& small ae, and slotting under condition of less than 0.5D

I Substrate coating strength

{ \scriptsize { 1 } } High performance ultra-fine substrate guarantees good wear and toughness { \scriptsize { 1 } } Use the latest Kila coatingfurnace from Balzers,with AlCr series coating

I Geometry structure

{ \scriptsize { 1 } } Usevariable pitch&helixdesign; Excellent vibration reduction performance

Model No	X-S4-12030
Specification	D123075*d12
Workpiecemnaterial	30CrMnSiA (36HRC)
Processing Type	Semi-Rough Machining
Cutting Method	Face Milling
Workpiecematerial	Vc=120 m/min
Feed Rate	fz=0.2mm/tooth
Cutting Depth	1~15mm
Cutting Width	0.5mm
Processing Equipment	TailikTLKVMC-855A
Cooling Method	Water-Soluble

Model No	X-BH2-08008
Specification	R4875*d8
Workpiece mnaterial	P20(32HRC)
Processing Type	Finishing
Cutting Method	Profile Milling
Workpiece material	Vc=200 m/min
FeedRate	fn=0.38mm/rev
Cutting Depth	0.1mm
Cutting Width	0.2mm
Cooling Method	Water-Soluble

Processed workpiece

Processing time:19 hoursand 30 minutes; the wearvalueofcompetitorproductsisgreater.

X-S3

3 flutes, square variable helix endmill for high efficiency machining

3° 43°/45° L2O 3 AlCrSiN 47°

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
X-S3-03009	3	9	50	4	A	.
X-S3-04011	4	11	50	4	B
X-S3-05013	5	13	50	6	B	.
X-S3-06016	6	16	50	6	B	.
X-S3-08020	8	20	60	8	B
X-S3-10025	10	25	75	10	B
X-S3-12030	12	30	75	12	B	.
X-S3-16036	16	36	100	16	B
X-S3-20045	20	45	100	20	B

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。	。

⊚ MostSuitable 0 Suitable

PAGE/057

X-C3

3 flutes, square variable helix endmill for high efficiency machining (chamfer)

OrderingCode	MillDia. (D)	Flute Length (Lc)	Chamfer (C)	Overall Length (L)	Shank Dia. (d)	Type	Stock
X-C3-06020	6	16	0.2	50	6	B
X-C3-08020	8	20	0.2	60	8	B
X-C3-10030	10	25	0.3	75	10	B
X-C3-12030	12	30	0.3	75	12	B	.
X-C3-16030	16	36	0.3	100	16	B

●Stock OAvailable Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels HardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Heatialistat alloy	Copperalloy	Aluminium alloy
	。

⑨ MostSuitable 0 Suitable

RecommendingCuttingPrametersP159

PAGE/058

X-S4

4 flutes, square variable helix endmill for high efficiency machining

OrderingCode	Mill Dia. (D)	(Lc)	Flute Length Overall Length (L)	Shank Dia. (d)	Type	Stock
X-S4-02006	2	6	50	4	A
X-S4-03009	3	9	50	4	A	.
X-S4-04011	4	11	50	4	B	.
X-S4-05013	5	13	50	6	A	.
X-S4-06016	6	16	50	6	B
X-S4-08020	8	20	60	8	B	.
X-S4-10025	10	25	75	10	B
X-S4-12030	12	30	75	12	B
X-S4-16036	16	36	100	16	B	.
X-S4-20045	20	45	100	20	B	.

●Stock 0 Available Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant	Copperalloy	Aluminium alloy
。	。				。

⑨ Most Suitable 0 Suitable

PAGE/059

X-C4

4 Flutes, Square Variabe Helix Endmill For High Efficiency Machining (Chamfer)

5° 20 AlCrSiN

OrderingCode	MilLDia.	Flute Length	Chamfer	OoverallLengh	Shank Dia.	Type	Stock
X-C4-03003	3	9	0.03	50	4	A
X-C4-03013	3	9	0.13	50	4	A
X-C4-04004	4	11	0.04	50	6	B
X-C4-04018	4	11	0.18	50	6	B
X-C4-05005	5	13	0.05	50	6	A	O
X-C4-05013	5	13	0.13	50	6	A
X-C4-05020	5	13	0.2	50	6	A
X-C4-06006	6	16	0.06	50	6	B	O
X-C4-06013	6	16	0.13	50	6	B	.
X-C4-06020	6	16	0.2	60	6	B	.
X-C4-08008	8	20	0.08	60	8	B
X-C4-08020	8	20	0.2	60	8	B	.
X-C4-10010	10	25	0.1	75	10	B
X-C4-10030	10	25	0.3	75	10	B	.
X-C4-12012	12	30	0.12	75	12	B	O
X-C4-12030	12	30	0.3	75	12	B
X-C4-16015	16	36	0.15	100	16	B	O
X-C4-16040	16	36	0.4	100	16	B	O
X-C4-20015	20	45	0.15	100	20	B	O
X-C4-20050	20	45	0.5	100	20	B	O

Stock 0 Available Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant	Copperalloy	Aluminium alloy
	。	。

⊚ MostSuitable 0 Suitable

PAGE/060

X-CN4

4 Flutes, Square Variabe Helix Endmill For High Efficiency Machining (Chamfer)

5° 0 AlCrSiN

Ordering Code		MiDiaFuteLnthdK		Dia.ck2)		ChamerOveralLegth hankDia		Type	Stock
X-CN4-03013	3	10	18	2.9	0.13	75	4	A
X-CN4-04018	4	12	20	3.8	0.18	75	4	B	.
X-CN4-05020	5	15	35	4.8	0.2	75	6	B	.
X-CN4-06020	6	16	24	5.8	0.2	100	6	B	.
X-CN4-08020	8	20	30	7.5	0.2	100	8	B
X-CN4-10030	10	25	40	9.5	0.3	150	10	B
X-CN4-12030	12	30	40	11	0.3	150	12	B	○
X-CN4-16040	16	36	50	15	0.4	150	16	B
X-CN4-20050	20	45	60	19	0.5	150	20	B

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels Hardenedsteels Hardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Heatiallistant alloy	Copperalloy	Aluminium alloy
	。				。

⊚ MostSuitable 0 Suitable

PAGE/061

X-R4

4 Flutes, Corner Radius, variabe Helix Endmill For High Efficiency Machining

5° LAO AlCrSiN

OrderingCode	Mill Dia. (D)	Flute Length (LC)	Corner (r)	OverallLength (L)	Shank Dia. (d)	Type	Stock
X-R4-03003	3	9	0.3	50	4	A
X-R4-03005	3	9	0.5	50	4	A	.
X-R4-04003	4	11	0.3	50	4	B
X-R4-04005	4	11	0.5	50	4	B
X-R4-05003	5	13	0.3	50	6	A
X-R4-05005	5	13	0.5	50	6	A
X-R4-06005	6	16	0.5	50	6	B
X-R4-06010	6	16	1	50	6	B	.
X-R4-08005	8	20	0.5	60	8	B
X-R4-08010	8	20	1	60	8	B
X-R4-10005	10	25	0.5	75	10	B	.
X-R4-10010	10	25	1	75	10	B
X-R4-10020	10	25	2	75	10	B
X-R4-12005	12	30	0.5	75	12	B
X-R4-12010	12	30	1	75	12	B
X-R4-12020	12	30	2	75	12	B
X-R4-14020	14	32	2	75	14	B
X-R4-16020	16	36	2	100	16	B

●Stock 0 Available Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardened steels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant	Copperalloy	Aluminium alloy
。	。				。

⊚ MostSuitable 0 Suitable

PAGE/062

X-B2

2 Flutes, Ball Nose Endmill For High Speed Machining

Ordering Code	Mill Dia. (D)	Ball Radius (R)	(LC)	Flute Length Overall Length Shank Dia. (L)	(d)	Type	Stock
X-B2-01002	1	0.5	2	50	4	A
X-B2-01503	1.5	0.75	3	50	4	A
X-B2-02004	2	1	4	50	4	A
X-B2-03006	3	1.5	6	50	4	A	O
X-B2-04008	4	2	8	50	4	B	.
X-B2-06012	6	3	12	50	6	B	.
X-B2-08014	8	4	14	60	8	B	.
X-B2-10018	10	5	18	75	10	B	.
X-B2-11020	11	5.5	20	75	12	B	.
X-B2-12022	12	6	22	75	12	B	.

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。	。

⊚ Most Suitable 0 Suitable

PAGE/063

X-BH2

2 Flutes, Ball Nose, long Shank Endmill For High Speed Machining

OrderingCode	Mill Dia. (D)	(R)	(LC)	Ball Radius Flute Length Overall Length Shank Dia. (L)	(d)	Type	Stock
X-BH2-04008	4	2	8	75	4	B
X-BH2-06012	6	3	12	60	6	B	.
X-BH2-06012H	6	3	12	75	6	B	.
X-BH2-08014	8	4	14	75	8	B	.
X-BH2-10018	10	5	18	100	10	B
X-BH2-12022	12	6	22	100	12	B

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant	Copperalloy	Aluminium alloy
	。

⑨ Most Suitable \bigcirc Suitable

Recommending Cutting Prameters P158

PAGE/064

UX Series High-efficiency integrated roughing and finishing machining

Adoptsa 4 5 ^ { \circ } large helix angle and double land design; the sharp cutting edge ensures tool edge strength simultaneously.

|The Bottom Edge Variable Index + 4 5 Large Spiral Angle Design Has Excellent Shock Absorption Performance And Stable Cutting Process.

IHigh Performance Matrix With AlCrSiN Coating,The Tool Has High Wear Resistance And High Toughness.

Model No	UX-S4-12030
Specification	D123075*D12
Workpiece material	Cast
ProcessingParameters	s=4krpm、f=2000mm/min、 ap=28mm、ae=lmm
Way of cutting	Dynamic Side Milling
Coolant	Emulsion

UX-S4

4 Flutes, Square Endmill For Steel HighEfficiency Machining

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	OverallLength (L)	Shank Dia. (d)	Type	Stock
UX-S4-01003	1	3	50	4	A
UX-S4-01505	1.5	5	50	4	A
UX-S4-61505	1.5	5	50	6	A
UX-S4-02006	2	6	50	4	A
UX-S4-62006	2	6	50	6	A
UX-S4-02508	2.5	8	50	4	A	C
UX-S4-62508	2.5	8	50	6	A
UX-S4-03009	3	9	50	4	A
UX-S4-63009	3	9	50	6	A
UX-S4-03511	3.5	11	50	4	A	C
UX-S4-63511	3.5	11	50	6	A
UX-S4-04011	4	11	50	4	B
UX-S4-64011	4	11	50	6	A	.
UX-S4-05013	5	13	50	6	A
UX-S4-06016	6	16	50	6	B
UX-S4-07020	7	20	60	8	A
UX-S4-08020	8	20	60	8	B
UX-S4-09023	9	23	75	10	A	C
UX-S4-10025	10	25	75	10	B
UX-S4-12030	12	30	75	12	B
UX-S4-14034	14	34	100	14	B	.
UX-S4-16036	16	36	100	16	B	.
UX-S4-18045	18	45	100	18	B	.
UX-S4-20045	20	45	100	20	B

●Stock 0 Available UponOrder

D/mm	Tol./mm
D≤12	0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Carbon stees	Pre-hardsned	Hasded	Hardened	Hardened	Stainless	Heatresat	Graphite	Callger	Alumium
		。							。

{0} Most Suitable 0 Suitable

RecommendingCutting PrametersP157

PAGE/066

UX-SL4

4 Flutes, Square Long Flute Endmill For Steel High Efficiency Machining

OrderingCode	MiuDia	Flute Length	OvralLengh	ShankDia.	Type	Stock
UX-SL4-01004	1	4	50	4	A	.
UX-SL4-02010	2	10	50	4	A
UX-SL4-03015	3	15	60	4	A	.
UX-SL4-63015	3	15	60	6	A	.
UX-SL4-04020	4	20	60	4	B
UX-SL4-64020	4	20	75	6	A	.
UX-SL4-05025	5	25	75	6	A
UX-SL4-06030	6	30	75	6	B	.
UX-SL4-08040	8	40	100	8	B	.
UX-SL4-10050	10	50	100	10	B	.
UX-SL4-12050	12	50	100	12	B	.
UX-SL4-14045	14	45	100	14	B	.
UX-SL4-16060	16	60	150	16	B	.
UX-SL4-18070	18	70	150	18	B
UX-SL4-20070	20	70	150	20	B	.

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Carloynsteels	Pre-hardened	Hasdehed	Hasteted	Haseled	Stainless	Hetresant	Graphite	Coplger	Alumium
	。	。

⊚ Most Suitable 0 Suitable

PAGE/067

UX-SH4

4 Flutes, Square Long Shank Endmill For Steel High Efficiency Machining

OrderingCode	MilDia.	Flute Length	OoverallLength	Shank Dia.	Type	Stock
UX-SH4-02010	2	10	75	4	A	.
UX-SH4-03012	3	12	75	4	A
UX-SH4-04011	4	11	75	4	B	.
UX-SH4-04015	4	15	75	4	B
UX-SH4-05020	5	20	75	6	A
UX-SH4-06016	6	16	75	6	B
UX-SH4-06020	6	20	75	6	B
UX-SH4-08020	8	20	100	8	B	.
UX-SH4-08025	8	25	100	8	B
UX-SH4-10030	10	30	100	10	B
UX-SH4-10035	10	35	100	10	B
UX-SH4-12035	12	35	100	12	B	.
UX-SH4-14036	14	36	150	14	B
UX-SH4-16036	16	36	150	16	B
UX-SH4-18045	18	45	150	18	B
UX-SH4-20045	20	45	150	20	B

D/mm	Tol./mm
D≤12	0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Carbonsteels Alloysteels	Pre-hardened steels	Hardened 45-55HRC	Hardened 55-65HRC	Hardened >65HRC	Stainless steels	Heat Aelsistant Alloy	Graphite	Copper alloy	Alumium alloy
。	。	。	。

⑨ MostSuitable （20 0 Suitable

RecommendingCuttingPrametersP157

PAGE/068

UX-R4

4 Flutes, Corner Radius Endmill ForSteel High Efficiency Machining

OrderingCode	Mill Dia. (D)	Flute Length (LC)	Corner (r)	Overall Length (L)	Shank Dia. (d)	Type	Stock
UX-R4-01502	1.5	5	0.2	50	4	A	.
UX-R4-02002	2	6	0.2	50	4	A	.
UX-R4-03002	3	9	0.2	50	4	A	.
UX-R4-03005	3	9	0.5	50	4	A
UX-R4-04002	4	11	0.2	50	4	B
UX-R4-04005	4	11	0.5	50	4	B	.
UX-R4-04010	4	11	1	50	4	B
UX-R4-05005	5	13	0.5	50	6	A
UX-R4-05010	5	13	1	50	6	A	.
UX-R4-06002	6	16	0.2	50	6	B
UX-R4-06005	6	16	0.5	50	6	B
UX-R4-06010	6	16	1	50	6	B
UX-R4-08005	8	20	0.5	60	8	B	.
UX-R4-08010	8	20	1	60	8	B	.
UX-R4-10005	10	25	0.5	75	10	B	.
UX-R4-10010	10	25	1	75	10	B	.
UX-R4-10020	10	25	2	75	10	B
UX-R4-12005	12	30	0.5	75	12	B	.
UX-R4-12010	12	30	1	75	12	B	.
UX-R4-12020	12	30	2	75	12	B	.

Stock 0 Available Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Carboyn steels	Pre-hardened	Hasdeted	Hasdeted	Hasded	Stainless	Heatresat	Graphite	Callper	Alumium
	。	。	。						。

⊚ Most Suitable OSuitable

PAGE/069

UX-RH4

4 Flutes Corner Radius, with Long Shank Length Endmill For Steel High Efficiency Machining

OrderingCode	Mill Dia. (D)	Flute Length (LC)	Corner (r)	Overall Length (L)	ShankDia. (d)	Type	Stock
UX-RH4-03005	3	9	0.5	75	4	A
UX-RH4-04005	4	11	0.5	75	4	B
UX-RH4-06005	6	16	0.5	75	6	B
UX-RH4-06010	6	16	1	75	6	B
UX-RH4-08005	8	20	0.5	100	8	B	.
UX-RH4-08010	8	20	1	100	8	B	.
UX-RH4-10005	10	25	0.5	100	10	B
UX-RH4-10010	10	25	1	100	10	B	.
UX-RH4-10020	10	25	2	100	10	B	.
UX-RH4-12005	12	30	0.5	100	12	B
UX-RH4-12010	12	30	1	100	12	B
UX-RH4-12020	12	30	2	100	12	B
UX-RH4-16005	16	36	0.5	150	16	B	.
UX-RH4-16010	16	36	1	150	16	B	.
UX-RH4-16020	16	36	2	150	16	B
UX-RH4-20010	20	45	1	150	20	B	.
UX-RH4-20020	20	45	2	150	20	B	.

●Stock 0 Available Upon Order

D/mm	Tol./mm
D≤12	0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Carbon steels	Pre-hardened	Hasded	Harded	Hardened	Stainless	Heatiresat	Graphite	Calpger	Alumium
	。	。	。			O

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrametersP157

PAGE /070

H Series

General machining for hardened steels

I Suitable For High HardnessWorkpiece

{ \scriptsize { 1 } } Suitable For Semi-finishing,Finishing Of Pre-hardened Steel, Hardened Steel,And High Speed steel.

I Suitable For Wide Range Of Application

⊚ Used On Injection Mould, Forging Die And Die-casting Mould Suitable For General Machining, High Speed Machining And Part Of High Efficient Machining.

I Substrate Coating Strength

{ \scriptsize { 1 } } High Performance, Ultra-fine And Super Hard Substrate.
⊚ Use The Latest Kila Coating Furnace From Balzers,With Our Self-developed TiAlSiN.

I Geometry Structure

{ \scriptsize { 1 } } Unique Geometry Design,Fine Grinded Cutting Edge, Enable Excellent Processing On Hardened Steel.

66 New Technology Makes Cutting Easier ”

Model No	H-R4-10005
Specification	D10R0.52575D10
Workpiecematerial	SKD61(52HRC)
Cutting speed	3800rpm
Feed rate	1200mm/min
Way of cutting	Side Milling, Face Milling
ap,ae	Face MillingAp=0.03mm Ae=5mm Side Milling Ap=0.1mm Ae=0.05mm
Coolant	Emulsion

Model No	H-B2-02004
Specification	R1450*d4
Workpiece material	SKD11(60HRC)
Cutting speed	20000rpm
Feed rate	2000mm/min
Way of cutting	Face Milling
ap,ae	ap=0.lmm,ae=0.3mm
Coolant	Oil Mist

H-S4

4 Flutes, Square Endmill For Hardened Steel Machining

1° 30° 5 TiAISiN

●Stock 0 Available Upon Order

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
H-S4-01003	1	3	50	4	A	.
H-S4-01504	1.5	4	50	4	A	.
H-S4-02006	2	6	50	4	A	.
H-S4-62006	2	6	50	6	A	.
H-S4-02508	2.5	8	50	4	A
H-S4-03008	3	8	50	4	A
H-S4-63008	3	8	50	6	A
H-S4-04011	4	11	50	4	B
H-S4-64011	4	11	50	6	A
H-S4-05013	5	13	50	6	A
H-S4-06016	6	16	50	6	B	.
H-S4-08020	8	20	60	8	B
H-S4-10025	10	25	75	10	B
H-S4-12030	12	30	75	12	B
H-S4-14032	14	32	100	14	B
H-S4-16040	16	40	100	16	B
H-S4-20045	20	45	100	20	B

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy

⊚ Most Suitable 0 Suitable

PAGE/073

H-SL4

4 Flutes, Square Long Flute Endmill For Hardened Steel Machining

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
H-SL4-03012	3	12	75	6	A
H-SL4-04015	4	15	75	6	A	.
H-SL4-05020	5	20	75	6	A	.
H-SL4-06020	6	20	75	6	B	.
H-SL4-08025	8	25	100	8	B
H-SL4-10030	10	30	100	10	B
H-SL4-12035	12	35	100	12	B
H-SL4-14040	14	40	100	14	B
H-SL4-16050	16	50	150	16	B
H-SL4-20055	20	55	150	20	B

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlessteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。	。	。	。

⑨ Most Suitable 0 Suitable

RecommendingCutting PrametersP161

PAGE/074

H-S6

6 Flutes, Square Endmill For Hardened Steel Machining

OrderingCode	Mill Dia. (D)	(Lc)	Flute Length Overall Length (L)	Shank Dia. (d)	Type	Stock
H-S6-06018	6	18	50	6	B
H-S6-08020	8	20	60	8	B
H-S6-10030	10	30	75	10	B
H-S6-12032	12	32	75	12	B
H-S6-16040	16	40	100	16	B	.
H-S6-20045	20	45	100	20	B	.

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。	。

⊚ Most Suitable 0 Suitable

RecommendingCuttingPrametersP163

PAGE/075

H-SL6

6 Flutes, Square Long Flute Endmill For Hardened Steel Machining

OrderingCode	Mill Dia. (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
H-SL6-06024	6	24	75	6	B
H-SL6-08032	8	32	75	8	B
H-SL6-10040	10	40	100	10	B
H-SL6-12045	12	45	100	12	B
H-SL6-16064	16	64	150	16	B
H-SL6-20075	20	75	150	20	B

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant	Copperalloy	Aluminium alloy
	。

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrametersP163

PAGE/076

4 Flutes, Corner Radius Endmill For Hardened Steel Machining

1° 30° TiAISiN 2

Ordering Code	Mill Dia. (D)	Flute Length (Lc)	Corner (r)	OverallLength (L)	Shank Dia. (d)	Type	Stock
H-R4-01002	1	2.5	0.2	50	4	A	.
H-R4-01502	1.5	4	0.2	50	4	A	.
H-R4-02002	2	5	0.2	50	4	A	.
H-R4-02005	2	5	0.5	50	4	A	.
H-R4-03002	3	8	0.2	50	4	A	.
H-R4-03005	3	8	0.5	50	4	A	.
H-R4-04002	4	10	0.2	50	4	B	.
H-R4-04003	4	10	0.3	50	4	B	.
H-R4-04005	4	10	0.5	50	4	B	.
H-R4-04010	4	10	1.0	50	4	B	.
H-R4-05005	5	13	0.5	50	6	A	.
H-R4-06005	6	16	0.5	50	6	B	.
H-R4-06010	6	16	1.0	50	6	B	.
H-R4-08005	8	20	0.5	60	8	B	.
H-R4-08010	8	20	1.0	60	8	B	.
H-R4-10005	10	25	0.5	75	10	B	.
H-R4-10010	10	25	1.0	75	10	B	.
H-R4-12005	12	30	0.5	75	12	B
H-R4-12010	12	30	1.0	75	12	B	.
H-R4-12020	12	30	2.0	75	12	B	.

●Stock OAvailable Upon Order

WorkpieceMaterials

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。

{0} Most Suitable 0 Suitable

PAGE/077

H-RH4

4 Flutes, Corner Radius Long Shank Endmill For Hardened Steel Machining

1° 30° TiAISiN

Ordering Code	Mill Dia. (D)	Flute Length (Lc)	Corner (r)	Overall Length (L)	Shank Dia. (d)	Type	Stock
H-RH4-04002	4	10	0.2	75	4	B
H-RH4-04003	4	10	0.3	75	4	B
H-RH4-04005	4	10	0.5	75	4	B
H-RH4-04010	4	10	1.0	75	4	B
H-RH4-06005	6	16	0.5	75	6	B
H-RH4-06010	6	16	1.0	75	6	B
H-RH4-08005	8	20	0.5	75	8	B
H-RH4-08010	8	20	1.0	75	8	B
H-RH4-08005-100	8	20	0.5	100	8	B
H-RH4-08010-100	8	20	1.0	100	8	B
H-RH4-10005	10	25	0.5	100	10	B
H-RH4-10010	10	25	1.0	100	10	B
H-RH4-12005	12	30	0.5	100	12	B
H-RH4-12010	12	30	1.0	100	12	B	.
H-RH4-12020	12	30	2.0	100	12	B	.

D/mm	Tol./m
D≤6	-0.015
6	-0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels HardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
		。

⑨ Most Suitable 0 Suitable

Recommending Cutting Prameters P161

PAGE/078

4 Flutes, Corner Radius Long Neck Endmill For Hardened Steel Machining

1° 30° D 4 TiAISiN

OrderingCode	Mill Dia. (D)	FluteLength (Lc)	Corner (r)	UnderNeck Length(L1)	Neck Dia.(d2)	OverallLength (L)	Shank Dia. (d)	Type	Stock
H-RN4-06005	6	6	0.5	18	5.8	75	6	B	.
H-RN4-06010	6	6	1.0	18	5.8	75	6	B	.
H-RN4-08005-75	8	8	0.5	24	7.8	75	8	B	.
H-RN4-08005	8	8	0.5	24	7.8	100	8	B
H-RN4-08010	8	8	1.0	24	7.8	100	8	B
H-RN4-10005	10	10	0.5	30	9.6	100	10	B
H-RN4-10010	10	10	1.0	30	9.6	100	10	B
H-RN4-10020	10	10	2.0	30	9.6	100	10	B	.
H-RN4-12005	12	12	0.5	36	11.5	100	12	B
H-RN4-12010	12	12	1.0	36	11.5	100	12	B
H-RN4-12020	12	12	2.0	36	11.5	100	12	B	.
H-RN4-16010	16	16	1.0	40	15.5	150	16	B	.
H-RN4-16020	16	16	2.0	40	15.5	150	16	B	.

D/mm	Tol./mm
D≤6	-0.015
6	0.02
D>12	-0.03

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels Hardenedsteels Hardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。

⑨ Most Suitable 0 Suitable

PAGE/079

H-B2

2 Flute, Ball Nose Endmill For HardenedSteel Machining

OrderingCode	Mill Dia. (D)	BallRadius (R)	Flute Length (LC)	OverallLength Shank Dia. (L)	(d)	Type	Stock
H-B2-01002	1	0.5	2	50	4	A	.
H-B2-01503	1.5	0.75	3	50	4	A	.
H-B2-02004	2	1	4	50	4	A	.
H-B2-02505	2.5	1.25	5	50	4	A
H-B2-03006	3	1.5	6	50	4	A
H-B2-63006	3	1.5	6	50	6	A
H-B2-04008	4	2	8	50	4	B
H-B2-64008	4	2	8	50	6	A
H-B2-05010	5	2.5	10	50	6	A
H-B2-06012	6	3	12	50	6	B
H-B2-07014	7	3.5	14	60	8	A
H-B2-08016	8	4	16	60	8	B
H-B2-10020	10	5	20	75	10	B	.
H-B2-12024	12	6	24	75	12	B	.
H-B2-16032	16	8	32	100	16	B	.

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrameters P162

PAGE/080

H-BH2

2 Flute, Ball Nose Long Shank Endmill For Hardened Steel Machining

OrderingCode	Mill Dia. (D)	BallRadius (r)	(Lc)	Flute Length Overall Length (L)	Shank Dia. (d)	Type	Stock
H-BH2-02004	2	1	4	75	4	A
H-BH2-03006	3	1.5	6	75	4	A	.
H-BH2-63006	3	1.5	6	60	6	A
H-BH2-63006-75	3	1.5	6	75	6	A
H-BH2-04008	4	2	8	75	4	B
H-BH2-64008-60	4	2	8	60	6	A
H-BH2-64008	4	2	8	75	6	A
H-BH2-05010	5	2.5	10	75	6	A
H-BH2-06012-60	6	3	12	60	6	B
H-BH2-06012	6	3	12	75	6	B
H-BH2-06012-100	6	3	12	100	6	B
H-BH2-08016-75	8	4	16	75	8	B	.
H-BH2-08016	8	4	16	100	8	B
H-BH2-10020	10	5	20	100	10	B
H-BH2-12024	12	6	24	100	12	B	.
H-BH2-16032	16	8	32	150	16	B	.

●Stock 0 Available Upon Order

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

Workpiece Materials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。

⊚ MostSuitable 0 Suitable

PAGE/081

HV Series

Machining series for hardened steels

IUsing ultrafine particle superhard alloy(O.2um) to process high hardness materials and achieve excellentperformance.

IHish hardness AlTiSiN coating,with high coating hardness and excellent high-temperature oxidationresistance,suitable forprocessinghigh hardnessmaterials.

IUnique tool structure,reasonable groove design,achieving excellent high hardness material processing.

IAfter coating treatment, effectively reducing friction,smoother chip removal,and better machinings surface quality.

Tooling	HV-R4-06010
tool specification	D6R11650d6
Workpiece material	SKD 61(60HRC)
Cutting Speed	114.9m/min
Feed per revolution	0.053mm/z
Cutting depth	0.03mm
Cutting width	3mm
Cooling conditions	air-cool

Bottombladewearcurve:

PAGE/082

HV-S4

4 Flutes, Square Length EndMill for Hardened Steels Machining

-6° TiAISiN

OrderingCode	Mill Dia (D)	Flute Length (Lc)	OverallLength (L)	Shank Dia. (d)	Type	Stock
HV-S4-01003	1	3	50	4	A
HV-S4-61003	1	3	50	6	B	O
HV-S4-01504	1.5	4	50	4	A
HV-S4-61504	1.5	4	50	6	B	O
HV-S4-02006	2	6	50	4	A
HV-S4-62006	2	6	50	6	A
HV-S4-02508	2.5	8	50	4	A
HV-S4-03008	3	8	50	4	A
HV-S4-63008	3	8	50	6	A	.
HV-S4-04011	4	11	50	4	B	.
HV-S4-64011	4	11	50	6	A
HV-S4-05013	5	13	50	6	A	.
HV-S4-06016	6	16	50	6	B	.
HV-S4-08020	8	20	60	8	B
HV-S4-10025	10	25	75	10	B	.
HV-S4-12030	12	30	75	12	B	.
HV-S4-14032	14	32	100	14	B
HV-S4-16040	16	40	100	16	B
HV-S4-20045	20	45	100	20	B

●Stock 0 Available Upon Order

Workpiece Materials

D/mm	Tol./mm
D≤6	-0.015
6	0.02
D>12	-0.03

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Hetiallistant alloy	Copperalloy	Aluminium alloy
	。

⊚ Most Suitable 0 Suitable

PAGE/083

HV-SL4

4 Flutes,With long Flute length EndMill for Hardened Steels Machining

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HV-SL4-63012	3	12	75	6	A	.
HV-SL4-64015	4	15	75	6	A	.
HV-SL4-05020	5	20	75	6	A
HV-SL4-06020	6	20	75	6	B
HV-SL4-08025	8	25	100	8	B
HV-SL4-10030	10	30	100	10	B
HV-SL4-12035	12	35	100	12	B
HV-SL4-14040	14	40	100	14	B
HV-SL4-16050	16	50	150	16	B
HV-SL4-20055	20	55	150	20	B

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Heatiallogtant alloy	Copperalloy	Aluminium alloy
	。

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrametersP164

PAGE/084

HV-S6

6 Flutes, Square EndMill for General Machining

Ordering Code	MilLDia	Flute Length	OoverallLength	Shank Dia.	Type	Stock
HV-S6-06018	6	18	50	6	B	O
HV-S6-08020	8	20	60	8	B
HV-S6-10030	10	30	75	10	B
HV-S6-12032	12	32	75	12	B
HV-S6-16040	16	40	100	16	B
HV-S6-20045	20	45	100	20	B

D/mm	Tol./mm
D≤6	-0.015
6	0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。

⑨ Most Suitable 0 Suitable

RecommendingCuttingPrametersP164

PAGE/085

HV-SL6

6 Flutes, Square EndMill for General Machining

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HV-SL6-06024	6	24	75	6	B	O
HV-SL6-08032	8	32	75	8	B
HV-SL6-10040	10	40	100	10	B
HV-SL6-12045	12	45	100	12	B
HV-SL6-16064	16	64	150	16	B
HV-SL6-20075	20	75	150	20	B

●Stock 0 Available Upon Order

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	HardenedsteelsHardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Heatialistant alloy	Copperalloy	Aluminium alloy
	。	。	。

⑨ Most Suitable 0 Suitable

Recommending Cutting Prameters P167

PAGE/086

HV-R4

OrderingCode	Mill Dia (D)	Flute Length (Lc)	CornerRadius (r)	OverallLength (L)	Shank Dia. (d)	Type	Stock
HV-R4-01002	1	2.5	0.2	50	4	A	O
HV-R4-01502	1.5	4	0.2	50	4	A
HV-R4-02002	2	5	0.2	50	4	A
HV-R4-02005	2	5	0.5	50	4	A
HV-R4-03002	3	8	0.2	50	4	A
HV-R4-03005	3	8	0.5	50	4	A	.
HV-R4-04002	4	10	0.2	50	4	B
HV-R4-04003	4	10	0.3	50	4	B	.
HV-R4-04005	4	10	0.5	50	4	B
HV-R4-05005	5	13	0.5	50	6	A	.
HV-R4-06005	6	16	0.5	50	6	B
HV-R4-06010	6	16	1.0	50	6	B
HV-R4-08005	8	20	0.5	60	8	B
HV-R4-08010	8	20	1.0	60	8	B
HV-R4-10005	10	25	0.5	75	10	B	.
HV-R4-10010	10	25	1.0	75	10	B	.
HV-R4-12005	12	30	0.5	75	12	B
HV-R4-12010	12	30	1.0	75	12	B	.
HV-R4-12020	12	30	2	75	12	B	.

●Stock 0 Available Upon Order

Workpiece Materials

D/mm	Tol./mm
D≤6	0.015
6	0.02
D>12	-0.03

Carbonsteels Alloysteels	Pre-hardened steels	Hardenedsteels HardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。

⊚ Most Suitable 0 Suitable

PAGE/087

HV-RN4

4 Flutes, Corner Radius,with Long neck Length EndMill for Genera Machining

OrderingCode	MiltD)ia.	Flute Length	Cormer	Lnder N/LLK	DNaeck2)	overlLength Shank Dia.		Type	Stock
HV-RN4-06005	6	6	0.5	18	5.8	75	6	A	.
HV-RN4-06010	6	6	1.0	18	5.8	75	6	B
HV-RN4-08010	8	8	1.0	24	7.8	100	8	B	.
HV-RN4-10005	10	10	0.5	30	9.6	100	10	B	.
HV-RN4-10010	10	10	1.0	30	9.6	100	10	B	.
HV-RN4-10020	10	10	2.0	30	9.6	100	10	B	.
HV-RN4-12005	12	12	0.5	36	11.5	100	12	B	.
HV-RN4-12010	12	12	1.0	36	11.5	100	12	B	.
HV-RN4-12020	12	12	2.0	36	11.5	100	12	B	.
HV-RN4-16010	16	16	1.0	40	15.5	150	16	B
HV-RN4-16020	16	16	2.0	40	15.5	150	16	B	.

D/mm	Tol./mm
D≤6	-0.015
6	-0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。	。	。	。

⑨ Most Suitable 0 Suitable

Recommending Cutting Prameters P165

PAGE/088

HV-RH4

4 Flutes, Corner Long Shank EndMill for General Machining

-6° 45° TiAISiN

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Corner Radius (r)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HV-RH4-04002	4	10	0.2	75	4	B	.
HV-RH4-04003	4	10	0.3	75	4	B	.
HV-RH4-04005	4	10	0.5	75	4	B	.
HV-RH4-04010	4	10	1	75	4	B	.
HV-RH4-06005	6	16	0.5	75	6	B
HV-RH4-06010	6	16	1	75	6	B
HV-RH4-08005-100	8	20	0.5	75	8	B	.
HV-RH4-08010-100	8	20	1	75	8	B	.
HV-RH4-08005	8	20	0.5	100	8	B
HV-RH4-08010	8	20	1	100	8	B
HV-RH4-10005	10	25	0.5	100	10	B	.
HV-RH4-10010	10	25	1	100	10	B
HV-RH4-12005	12	30	0.5	100	12	B
HV-RH4-12010	12	30	1	100	12	B
HV-RH4-12020	12	30	2	100	12	B

●Stock 0 Available Upon Order

D/mm	Tol./mm
D≤6	-0.015
6	0.02
D>12	-0.03

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。

⑨ Most Suitable 0 Suitable

PAGE/089

HV-B2

2 Flutes, Ball Nose End Mill for Hardened Steels Machining

OrderingCode	MilDia	Flute Length	Ball Radius	OoverallLength	Shank Dia	Type	Stock
HV-B2-01002	1	0.5	2	50	4	A
HV-B2-01503	1.5	0.75	3	50	4	A
HV-B2-02004	2	1	4	50	4	A
HV-B2-02505	2.5	1.25	5	50	4	A
HV-B2-03006	3	1.5	6	50	4	A
HV-B2-63006	3	1.5	6	50	6	A
HV-B2-04008	4	2	8	50	4	B
HV-B2-64008	4	2	8	50	6	A
HV-B2-05010	5	2.5	10	50	6	A
HV-B2-06012	6	3	12	50	6	B
HV-B2-07014	7	3.5	14	60	8	A
HV-B2-08016	8	4	16	60	8	B
HV-B2-10020	10	5	20	75	10	B	.
HV-B2-12024	12	6	24	75	12	B	.
HV-B2-16032	16	8	32	100	16	B	.

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	45-55HRC	Hardenedsteels HardenedsteelsHardenedsteels 55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
	。	。

⑨ MostSuitable 0 Suitable

RecommendingCuttingPrametersP166

PAGE/090

HV-BH2

2 Flutes, Ball Nose with Long Shank Length End Mill for General

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Ball Radius (r)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HV-BH2-02004	2	1	4	75	4	A
HV-BH2-03006	3	1.5	6	75	4	A
HV-BH2-63006	3	1.5	6	75	6	A
HV-BH2-04008	4	2	8	75	4	A
HV-BH2-64008	4	2	8	75	6	A
HV-BH2-05010	5	2.5	10	75	6	A
HV-BH2-06012	6	3	12	75	6	B
HV-BH2-06012-100	6	3	12	100	6	B
HV-BH2-08016-75	8	4	16	75	8	B
HV-BH2-08016	8	4	16	100	8	B
HV-BH2-10020	10	5	20	100	10	B	.
HV-BH2-12024	12	6	24	100	12	B	.
HV-BH2-16032	16	8	32	150	16	B	.

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

WorkpieceMaterials

Carbonsteels Alloysteels	Pre-hardened steels	HardenedsteelsHardenedsteelsHardenedsteels 45-55HRC	55-65HRC	>65HRC	Stainlesssteels	Tialloy Heat-resistant alloy	Copperalloy	Aluminium alloy
。	。	。

⊚ Most Suitable 0 Suitable

PAGE/091

HA20 Series

Aluminum Alloy End Mills For General Machining

Suitable for semi-finishing and finishing of aluminum alloys ( { \mathsf { S i } } < 1 2 % ) andcopperalloys （204号 ( < 2 0 0 \mathsf { H B } ) .

I Unique sharp cutting edge and vibration-damping design effectively prevent chatter and resolve built-up edge (BUE)issues.

ICutting edges employ ultra-fine grinding technology for superior surface finish and extended tool life.

Model	HA20-S3-06016
Specification	D61650*d6
Workpiecematerial	Aluminum Alloy Housing (150 HB)
CuttingPrameters	S=6krpm,F=600mm/min ap=7mm,ae=0.05mm
CoolingMethodns	Emulsion
Machining Operation	Profile Finishing

HA20-S3

3 Flutes, Square Endmill For Aluminium Alloys General Machining

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HA20-S3-01003	1	3	50	4	A
HA20-S3-61003	1	3	50	6	A
HA20-S3-01504	1.5	4	50	4	A	.
HA20-S3-61506	1.5	6	50	6	A	.
HA20-S3-02006	2	6	50	4	A
HA20-S3-62006	2	6	50	6	A
HA20-S3-02508	2.5	8	50	4	A
HA20-S3-62508	2.5	8	50	6	A
HA20-S3-03009	3	9	50	4	A
HA20-S3-63009	3	9	50	6	A
HA20-S3-03510	3.5	10	50	4	A

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

Workpiece Materials

Cast Iron	Carboy seesteadsted		Hardene5sHeelds	Hardenedsteels	Hardened steels	Stanless	Tialloy	Graphite	Colpger	Alumi-num alloy
									。

⊚ MostSuitable \bigcirc Suitable

PAGE/093

HA20-S3

3 Flutes, Square Endmill For Aluminium Alloys General Machining

OrderingCode	Mill Dia (D）	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HA20-S3-04011	4	11	50	4	B
HA20-S3-64011	4	11	50	6	A
HA20-S3-05013	5	13	50	6	A	.
HA20-S3-06016	6	16	50	6	B
HA20-S3-08020	8	20	60	8	B
HA20-S3-10030	10	30	75	10	B
HA20-S3-12035	12	35	75	12	B	O
HA20-S3-14034	14	34	100	14	B
HA20-S3-16036	16	36	100	16	B
HA20-S3-20045	20	45	100	20	B

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

Cast Iron	Calby stes sreharded		Hardened stels	Hardenedsteels	Hardened steels	Stanless	Tialloy	Graphite	Caler	Alumi-num
									。	。

⊚ Most Suitable OSuitable

RecommendingCuttingPrametersP168

PAGE/094

HA20-SL3

3 Flutes, Square Endmill For Aluminium Alloys General Machining

OrderingCode	Mill Dia (D)	Flute Length (Lc)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HA20-SL3-02020	2	20	75	4	A
HA20-SL3-03025	3	25	75	4	A
HA20-SL3-04030	4	30	75	4	B
HA20-SL3-06035	6	35	75	6	B
HA20-SL3-08040	8	40	100	8	B
HA20-SL3-10045	10	45	100	10	B
HA20-SL3-12050	12	50	100	12	B
HA20-SL3-16060	16	60	150	16	B
HA20-SL3-20070	20	70	150	20	B

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

Cast Iron	Caloy steesSreharded		Hardene5stels	Hardened steels	Hardened steels	Stainless	Tialloy	Graphite	Ccappger	Alumi-num alloy
									。	。

⊚ Most Suitable \bigcirc Suitable

PAGE/095

HA20-R3/RH3

3 Flutes, Corner Radius Endmill For Aluminium Alloys General Machining

OrderingCode	Mill Dia (D)	Flute Length (Lc)	(r)	CornerRadius OverallLength ShankDia. (L)	(d)	Type	Stock
HA20-R3-01002	1	3	0.2	50	4	A
HA20-R3-02002	2	6	0.2	50	4	A
HA20-R3-03002	3	9	0.2	50	4	A
HA20-R3-03003	3	9	0.3	50	4	A
HA20-R3-03005	3	9	0.5	50	4	A
HA20-R3-04002	4	11	0.2	50	4	B
HA20-R3-04005	4	11	0.5	50	4	B
HA20-R3-04010	4	11	1	50	4	B
HA20-R3-05002	5	13	0.2	50	6	A
HA20-R3-05005	5	13	0.5	50	6	A
HA20-R3-05010	5	13	1	50	6	A
HA20-R3-05015	5	13	1.5	50	6	A
HA20-R3-06005	6	16	0.5	50	6	B
HA20-R3-06010	6	16	1	50	6	B
HA20-R3-06015	6	16	1.5	50	6	B
HA20-R3-06020	6	16	2	50	6	B
HA20-R3-08005	8	20	0.5	60	8	B
HA20-R3-08010	8	20	1	60	8	B
HA20-R3-08015	8	20	1.5	60	8	B
HA20-R3-08020	8	20	2	60	8	B
HA20-R3-10003	10	25	0.3	75	10	B
HA20-R3-10005	10	25	0.5	75	10	B
HA20-R3-10010	10	25	1	75	10	B	.
HA20-R3-10015	10	25	1.5	75	10	B
HA20-R3-10020	10	25	2	75	10	B

●Stock OAvailable Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

Cast Iron	Calby seseardehed		Hardenedsteels	Hardened steels	Hardened stees	Stainles	Tialloy	Graphite	Collger	Alumi-num
									。	。

⊚ MostSuitable \bigcirc Suitable

PAGE/096

HA20-R3/RH3

3 Flutes, Corner Radius Endmill For Aluminium Alloys General Machining

S12° B\~D

OrderingCode	Mill Dia (D)	Flute Length (Lc)	CornerRadius (r)	OverallLength (L)	ShankDia. (d)	Type	Stock
HA20-R3-10030	10	25	3	75	10	B
HA20-R3-12005	12	30	0.5	75	12	B
HA20-R3-12010	12	30	1	75	12	B
HA20-R3-12020	12	30	2	75	12	B
HA20-R3-12030	12	30	3	75	12	B
HA20-RH3-06002	6	16	0.2	75	6	B
HA20-RH3-06005	6	16	0.5	75	6	B
HA20-RH3-06010	6	16	1	75	6	B
HA20-RH3-06015	6	16	1.5	75	6	B
HA20-RH3-06020	6	16	2	75	6	B
HA20-RH3-08005	8	20	0.5	100	8	B
HA20-RH3-08010	8	20	1	100	8	B
HA20-RH3-08015	8	20	1.5	100	8	B
HA20-RH3-08020	8	20	2	100	8	B
HA20-RH3-10005	10	25	0.5	100	10	B
HA20-RH3-10010	10	25	1	100	10	B
HA20-RH3-10015	10	25	1.5	100	10	B
HA20-RH3-10020	10	25	2	100	10	B
HA20-RH3-10025	10	25	2.5	100	10	B
HA20-RH3-12005	12	30	0.5	100	12	B
HA20-RH3-12010	12	30	1	100	12	B
HA20-RH3-12015	12	30	1.5	100	12	B	.
HA20-RH3-12020	12	30	2	100	12	B	.
HA20-RH3-12025	12	30	2.5	100	12	B

●Stock OAvailable Upon Order

D/mm	Tol./mm
D≤12	-0.02
D>12	-0.03

WorkpieceMaterials

CastIron	Calby stels stehardeted		Hardenedsteels	Hardened steels	Hardened steels	Stainles	Tialloy	Graphite	colger	Alumi-num alloy
									。

⊚ MostSuitable \bigcirc Suitable

PAGE/097

HA20-B2

2 Flutes, Ballnose Endmill For Aluminium Alloys General Machining

Ordering Code	Mill Dia (D)	Flute Length (Lc)	Ball Radius (r)	Overall Length (L)	Shank Dia. (d)	Type	Stock
HA20-B2-01002	1	0.5	2	50	4	A
HA20-B2-02004	2	1	4	50	4	A
HA20-B2-03006	3	1.5	6	50	4	A
HA20-B2-04008	4	2	8	50	4	B	.
HA20-B2-05010	5	2.5	10	50	6	A	.
HA20-B2-06012	6	3	12	50	8	B	.
HA20-B2-07014	7	3.5	14	60	8	A	.
HA20-B2-08014	8	4	14	60	9	B	.
HA20-B2-09016	9	4.5	16	75	10	A	.
HA20-B2-10018	10	5	18	75	10	B	.
HA20-B2-12022	12	6	22	75	12	B	.
HA20-B2-16026	16	8	26	100	16	B	.

R/mm	Tol./mm
R≤6	-0.01
R>6	-0.015

WorkpieceMaterials

Cast Iron	Carlby stels stehadeted		Hardened stees	Hardened steels	Hardened stees	Stainless	Tialloy	Graphite	Collger	Alumi-num

⊚ MostSuitable \bigcirc Suitable

PAGE/098

AS Series Aluminum alloy end mills for high-gloss & high-efficiency machining

Suitable for high-efficiency roughing and finishing of aluminum alloys (Si 1 2 % ,meetinghigh-gloss requirements for side milling and face milling(appearance machining).

Unique flute design enhances chip evacuation and metal removal rate, suitable forhigh-efficiency machining with large depth of cut and large width of cut.

IPolished cutting edges provide extremely high grinding quality; eliminates uneven finishes and tool marks in appearance machining, meeting high cosmetic requirements.

I Upgraded substrate with ultra-fine grain material offers higher wear resistance for morestable tool life.

|Widely used in aerospace,3C,and other fields; coolant (water-based) recommended.

Model	AS-S3-04011
Specification	D41150*d4
Workpiecematerial	Aluminum Alloy (AL6061)
CuttingPrameters	S=20k rpm,F=1100 mm/min ap=6 mm,ae=0.01 mm
Cooling Methodns	Emulsion
Machining Operation	Finishing Chamfer Milling