威利水电设备材料厂宣传册 - 电子画册在线预览、各类电子画册在线制作-云展网平台

镶嵌式、法兰式橡胶鸭嘴阀

Mosaic type, flange type rubber duckbill valve

XH81

XH41

镶嵌式主要连接尺寸Mosaic type main joint dimension

型号type	管道公称直径nominal diameter ofpipe	长度Llength	高度Hheight	法兰外径Cexternaldiameterofflange
XH8150-125-X	50	125	47	150
XH8180-175-X	80	175	72	200
XH81100-225-X	100	225	97	225
XH81150-320-X	150	320	47	275
XH81200-375-X	200	375	197	338
XH81250-475-X	250	475	247	400
XH81300-560-X	300	560	297	485
XH81350-625-X	350	625	344	525
XH81400-700-X	400	700	394	588
XH81450-780-X	450	780	444	625
XH81500-880-X	500	880	494	688
XH81600-1000-X	600	1000	494	800
XH81700-1000-X	700	1100	694	969
XH81800-1260-X	800	1260	794	1080
XH81900-1400-X	900	1400	894	1150
XH811000-1520-X	1000	1520	988	125
XH811200-1725-X	1200	1725	1188	1485

法兰式主要连接尺寸 Flange type main joint dimension

型号type	管道公称直径nominaldiameter ofpipe	长度Llength	高度Hheight	法兰外径Cexternaldiameterofflange
XH4150-150-F	50	150	100	150
XH4180-220-F	80	220	140	200
XH41100-250-F	100	250	200	225
XH41150-340-F	150	340	265	275
XH41200-420-F	200	420	325	338
XH41250-520-F	250	520	425	400
XH41300-620-F	300	620	525	485
XH41350-700-F	350	700	625	525
XH41400-800-F	400	800	725	588
XH41450-900-F	450	900	825	625
XH41500-980-F	500	980	925	688
XH41600-1120-F	600	1120	1025	800
XH41700-1180-F	700	1180	1125	969
XH41800-1350-F	800	1350	1400	1080
XH41900-1500-F	900	1500	1525	1150
XH411000-1600-F	1000	1600	1725	1325
XH411200-1840-F	1200	1840	1950	1485

XHS型吊架弹簧减振器 XHS type hanger spring vibration isolator

弹性支吊架主要用于电厂汽，水管道或锅炉设备，在运行中产生热位移及其设备装置上，根据管道受力情况计算确定的弹性支吊架工作和热位移要求。本厂将弹性支吊架按照设计荷载进行整定：既弹簧预压并锁定冷态荷载位置上：同时标上冷态时的理论工作位置弹性支吊架在出厂前制造厂进行了整定，当安装到管道和设备上后，以罗纹调整，将锁定锁脱开，这时弹簧的实际承载就是设计所要求的冷态荷载。

The flexible hanger spring is mainly used in the steam and water pipe or boiler unit and other equipments of the power plant. It produces thermal displacement during its running. In accordance with the working and thermal displacement requirements of flexible supports and hangers determined by calculating the load-carrying condition of the pipe, our factory will set the flexible supports and hangers according to the design load: spring preloading and lock on the cold load position: at the same time mark the theoretical working position when in cold state, the flexible supports and hangers has been set before delivery by manufactory. After install it on the pipe and equipment, adjust the screw and declutch the lock, then the actual load bearing of the spring is the design required cold load.

设计安装数据表：c(注：特殊需要另行制造)

Data sheet for design and installation: c (note: we can manufacture separately to meet your special need)

XHS-5	XHS—10	XHS-20	XHS-30	XHS-40	XHS-60	XHS-80	XHS-10O	XHS-150	XHS-200	XHS-250	XHS-320	XHS-500	XHS-700
30-80	80-170	130-260	190-390250	-530400	-800550	-1050750	-15001000	-2000	1300-2650	1700-3100	2310-4160	3000-6800	3500-1000
3.2-mm	7.5N-mm	11n-mm1	1.5N-rnm	14N-m	21N-m	32N-mm	40N-mm	45N-r-mm	58N-mm	56N-m	77N-m	200N-rnm	535N-m
3.0-5.0	3.0-4.8	3.0-4.5	2.5-4.02.6	-3.72.6	-3.6	2.7-3.8	2.6-3.6	2.3-3.3	2.3-3.3	2.9-2.1	2.9-2.1	4-2.6	4.5-3.4
9.5	10.5	12	165	18	19	17	19	23	23	30	30	15	12
25	23	23	34	38	38	33	38	45	46	55	54	35	20
50	50	50	70	95	95	100	100	15	15	115	116	95	95
50	50	50	100	105	105	110	110	130	130	130	130	105	105
50	50	50	70	80	80	90	90	100	100	100	100	85	85
100	100	100	130	155	155	180	180	200	200	200	200	210	210
10	10	10	12	12	12	12	12	13	13	13	13	18	18
8	8	8	10	10	10	10	10	12	12	12	12	16	16

V型吊架阻尼弹簧减震器V type hanger damping spring vibration absorber

本产品是一种以减振弹簧、橡胶复合垫、阻尼等组成的预应力吊架减振器：主要用于各种风机、管道、动力设备的吊装隔振降噪，也可用于精密仪器、仪表的吊装消极隔振。

This product is a kind of prestressing hanger vibration absorber composed of anti-vibrating spring, rubber composite gasket and damp and so on, which is mainly used for the hoisting vibration isolation and noise reduction of variable fans, pipes and power equipments, it can also used for the hoisting passive vibration isolation of precision instruments and meters.

设计安装数据表（注：特殊需要另行制造）

Data sheet for design and installation (note: we can manufacture separately to meet your special ne ed)

XHS-5	XHS-10	XHS-20	XHS-30	XHS-40	XHS-60	XHS-80	XHS-100	XHS-150	XHS-200	XHS-250	XHS-320	XHS-500	XHS-700
30-80	80-170	130-260	190-390	250-530	400-800	550-1050	750-1500	1000-2000	1300-26501700	-31002310	-4160	3000-6800	3500-10000
3.2-mm	7.5n-mm	11n-mm	11.5n-mm	14n-mm	21n-mm	32n-mm	40n-mm	45n-mm	58n-mm	56n-mm	77n-mm	200n-mm	535n-mm
3.0-5.0	3.0-4.8	3.0-4.5	2.5-4.0	2.6-3.7	2.6-3.6	2.7-3.8	2.6-3.6	2.3-3.3	2.3-3.3	2.9-2.1	2.9-2.1	4-2.6	4.5-3.4
95	10.5	12	16.5	18	19	17	19	23	23	30	30	15	12
25	23	23	34	38	38	33	38	45	46	55	54	35	20
50	50	50	70	95	95	100	100	115	115	115	116	95	95
50	50	50	100	105	105	110	110	130	130	130	130	105	105
50	50	50	70	80	80	90	90	100	100	100	100	85	85
100	100	100	130	155	155	180	180	200	200	200	200	210	210
10	10	10	12	12	12	12	12	13	13	13	13	18	18
8	8	8	10	10	10	10	10	12	12	12	12	16	16

HQ型阻尼弹簧悬吊减震器

HQ type dumping spring suspending vibration absorber

主要数据 Main data

型号Type	HQ-30	HQ-50	HQ-80	HQ-140	HQ-200	HQ-240	HQ-300	HQ-350	HQ-400
承载范围kgload range	20-30	30-50	50-80	80-140	140-200	200-240	240-300	300-350	350-400
自振频率Hznaturalfrequencyof vibration	4.8-2.8	4.5-3.2	4.9-3.5	4.7-3.5	4.6-3.3	4.7-3.3	4.7-3.2	4.8-3.3	4.8-3.2
变形范围mmdistortion range	11-30	12-25	10-20	10-22	12-23	12-24	13-25	13-25	13-25
D(直径)mmDiameter	48	60	76	76	89	118	118	132	132
H(高度)mmHeight	126	138	178	178	190	244	244	258	258
h(管高)mmheight of pipe	98	110	136	136	150	198	198	210	210

主要数据 Main data

型号Type	HQA-15	HQA-30	HQA-40	HQA-60	HQA-80	HQA-120	HQA-160	HQA-180	HQA-200
承载范围kgload range	8-15	15-30	30-40	40-60	60-80	80-120	120-160	160-180	180-200
自振频率Hznaturaifrauoency	4.8-3.3	4.2-3	3.8-2.7	3.5-2.5	3.5-2.5	3.5-2.7	3.6-2.7	3.6-2.7	3.9-2.6
变形范围mmdistortion range	11-22	13-25	17-30	20-30	19-35	19-35	20-30	20-32	20-33
A(宽度)mmwidth	38	62	80	80	90	90	110	110	125
B(厚度)mmthickness	30	40	50	50	60	60	70	70	80
H(高度)mmheight	132	138	178	178	214	214	230	230	238
h(框高)mmheight of frame	100	105	140	140	172	172	182	182	190

ET型阻尼弹簧減震器 ET type dumping spring vibration absorber

主要数据 Main D ate

ETA型

ETB型

型号Type	A型R寸 Dimensi on of type A		最佳荷载(kg)	B型R寸 Dimension of type B		最佳荷载(kg)best load
型号Type	H	D	best load	H	D	最佳荷载(kg)best load
ET1-1	88	106	22	96	135	22
ET1-2	88	106	35	96	135	35
ET1-3	88	106	48	96	135	48
ET1-4	88	106	78	96	135	78
ET1-5	108	178	85	116	220	85
ET1-6	108	178	105	116	220	105
ET1-7	108	178	148	116	220	148
ET1-8	108	178	180	116	220	180
ET1-9	128	220	240	138	260	240
ET1-10	128	220	320	138	260	320
ET1-11	128	220	400	138	260	400
ET1-12	162	266	450	172	315	450
ET1-14	162	266	500	172	315	500
ET1-15	162	266	680	172	315	680
ET1-16	162	266	780	172	315	780
ET1-18	202	306	600	212	365	600
ET1-19	202	306	800	212	365	800
ET1-20	202	306	900	212	365	900
ET1-22	202	306	1150	212	365	1150
ET1-23	270	350	1410	288	420	1410
ET1-24	270	350	1900	288	420	1900
ET1-25	270	350	2800	288	420	2800

罩型通气管

Bell type vent pipe

罩型通气尺寸表

弯管型通气管

弯管型通气管尺寸表

Bell type vent pipe dimensions table

序号Number	代号Code	名称Name	规格Specifications		数量Amout	材料Materials
1	403-105	立管Code	Z-200	φ219×6	1	Q235-A
			Z-300	φ325×6
			Z-400	φ426×8
			Z-600	φ630×8
2	403-107	内罩Code	Z-200	φ325×6	1	Q235-A
			Z-300	φ426×8
			Z-400	φ529×8
			Z-600	φ720×8
3	403-109	外罩Code	Z-200	φ426×8	1	Q235-A
			Z-300	φ529×8
			Z-400	φ720×8
			Z-600	φ1020×10
4	GB5783-86	螺栓Code	Z-200	φ10×20	3	A2-70
			Z-300	φ10×20
			Z-400	φ12×20
			Z-600	φ12×20
5	GB97.2-85	垫圈Code	Z-200	10	3	200HV
			Z-300	10
			Z-400	12
			Z-600	12
6	GB5783-86	螺栓Code	Z-200	M12×20	3	A2-70
			2-300	M12×20
			Z-400	M14×20
			Z-600	M14×20
7	GB97.2-85	垫圈Code	Z-200	12	3	200HV
			Z-300	12
			Z-400	14
			Z-600	14

Bend pipe type vent pipe dimensions table

序号Num ber	代号Code	名称Name		规格Specifications		数量Amout	材料Materiak
1	403-100	立管Code		W-100	φ108×4	1	组件Code
				W-150	φ159×5
				W-200	φ219×6
2	403-101	凸面法兰弯头Specifications		W-100	Dn100×90	1	Q235-A
				W-150	DN150× 90
				W-200	DN200 × 90
3	GB5782-86	螺栓Code		W-100	M16×45	1	A2-70
				W-150	M20×50
				W-200	M20×55
4	GB6172-86	螺母Code		W-100	M16	3	A2-70
				W-150	M20
				W-200	M20
5	GB97.2-85	垫圈Code		W-100	16	3	200HV
				W-150	20
				W-200	20
6		滤层Num ber	合成纤维网Num ber	W-100	φ138		尼龙1010涤纶JP8(20 目)PA1010PolyesterJPS (20 mesh)
				W-150	φ198
				W-200	φ254
			纱布Num ber	W-100	φ138	1	医用纱布(301-1)PA1010PolyesterJP8 (20 mesh)
				W-150	φ198
				W-200	φ254
			合成纤维网Num ber	W-100	φ138		尼龙1010涤纶JP6(16目)PA1010PolyesterJP8 (20 mesh)
				W-150	φ198
				W-200	φ254

吸水喇叭口支架 Water absorption horn mouth bracket

外形尺寸表Dimension Table

型号Type	配电吸水喇叭管规格Speaker Distributionsuction pipe specifications	D1	D2	h	H1	H	d	k
ZB1	φ273×Φ400	Φ425	φ325	40	400	458	φ18	10
ZB2	Φ325×Φ478	Φ500	φ400	40	500	558	φ18	10
ZB3	φ426×Φ630	φ650	φ550	40	500	558	φ18	11

型号Type	配电吸水喇叭管规格Speaker Disributionsuction pipe specifications	D1	D2	h	H1	H	d	K
ZCL	Φ529×φ770	φ800	φ700	40	600	662	φ22	12
ZC2	Φ630×φ880	φ900	φ800	40	650	712	φ22	12
ZC3	φ720×φ980	φ1010	φ900	40	670	732	φ22	12

吸水喇叭管及支架

型号Type	配用吸水喇叭管规格Speakcer Distributionsucti on pipe spe aific ations	D1	D2	D3	D4	h	H1	H	d	K
ZA1	Φ108×Φ159	φ180	φ100	φ210	φ320	40	400	454	φ14	8
ZA2	Φ159×Φ245	φ265	φ180	φ320	φ460	40	400	456	φ16	8
ZA3	Φ219×Φ325	φ345	φ250	φ400	φ540	40	400	456	φ16	9

Water absorption horn pipe and bracket

型号Type	配电吸水喇叭管规格Speaker Distributionsuction pape specifications	D	H	L	L1	L2	L3	H	H1	δ	K	重量Wēight
ZD1	φ720×Φ980	φ1030	700	1046	28	199	60	30	100	8	8	72.22
ZD2	Φ820×Φ1120	φ1170	730	1186	28	228	60	30	100	8	8	81.49
ZD3	Φ920×φ1220	φ1270	780	1286	28	249	70	30	110	8	8	99.34
ZD4	Φ1020×φ1350	φ1400	830	1416	28	276	70	30	110	8	8	109.25
ZD5	Φ1120×φ1620	φ1670	1030	1686	28	332	80	30	120	8	8	145.83
ZD6	Φ1420×φ1880	φ1930	1150	1946	28	386	80	30	120	8	8	168.33

承口直口管道快速堵漏器

bell mouth/ straight mouth pipe quick leak stopping device

规格及主要尺寸：mm Specification and main dimension: mm

水泥管堵漏器系列

cement pipe leak stopping device series

通径Diameter	直口长度LminStraight mouthlength	承口长度Straight mouth length
100	350	430
200	350	480
300	400	600
400	400	760
600	500	770
800	500	782
1000	500	800

铸铁管堵漏器系列

Cast iron pipe leak stopping device seri

通径DNDiameter	直径长度LminStraight mouthlength	承口长度Straight mouth length
80	230	260
100	250	260
150	300	270
200	350	270
250	350	270
300	400	300
350	400	337
400	500	350
450	500	350
500	500	360
600	500	370
700	600	370
800	600	380
900	700	390
1000	700	390
1200	820	450

SKX-10型直管堵漏器和承口堵漏器均有两种型号(A型和B型)，A型为全密封面加长型。B型为通用型。材质为铸铁和球墨铸铁件两种，密封圈为特殊橡胶材料。本产品有三通管道堵漏器和变径管道堵漏器。

SKX-10型直管墙漏器

本产品适用于各种管道的断裂，爆管的维护和抢修，不需要停水，在断裂爆管处安装直管堵漏器，快速堵漏，保障管道正常供水。

SKX-10型承口堵漏器

本产品用于铸铁管，球墨铸铁管的承口处漏水的抢修，降低劳动强度，方便快捷，快速堵漏，保障管道正常供水。

直管卡式快速接头(又名：直管开边抢修器)

型号ZKX-10Z/P

材料：球墨铸铁

Both SKX-10 type straight leak stopping device and SKX-10 type bell mouth leak stopping device have two models (A-type and B-type). B-type is the general type. The material is divided into two kinds: cast iron and nodular iron casting The seal ring is special rubber material. This product has three-way pipe leak stopping device and tapered pipeline leak stopping device.

SKX-10 type straight pipe wail leakage device

This product is applicable to the maintenance andrush repair of the fracture and burst of various pipes. Water stopping is not needed. Straight pipe leak stopping device should be installed where there is fracture and pipe burst. Rapidly stop the leak and ensure normal water supply.

SKX-10 type bell mouth leak stopping device

This product is applied to the rush repair of leak on in the bell mouth of cast iron pipe and the nodular cast iron pipe. Reduce the labour intensity, fast and convenient. Rapidly stop the leak and ensure normal water supply.

Straight pipe cassette quick joint (alsoknown as: straight pipe splitting rushrepair device)

ModeI: ZKX-10Z/P

Material: nodularcast iron

ZKX-10Z/P(铸铁管用) ZKX-10Z/P(used for cast iron pipe)

公称通径DNNominal diameter	L	L	G
80	250	220	1/2"
100	270	230	1/2"
150	270	230	1/2
200	310	270	3/4"
250	350	310
300	430	375	119

ZKX-10P(PVC、PE、镀锌管用) ZKX-10P(used for PVC, PE, galvanized pipe) 规格及主要尺寸：mm Specification and main dimension:mm

公称通径DNNominaldiameter	L	L,	G
90	220	250	1/2
110	230	260	1/2°
150	230	260	3/4
200	260	300	1

性能规范数据 Performance specification data

公称压力Mpa Nominaldiameter		1.0-1.5
试验压力Mpa Testpressure Mpa	深度Depth	1.3-2.0
	密封 Seal	1.1-2.0
20℃以下允许工作压力MPa 20℃ below allow able working pressure Mpa		1.0-1.5
适用泪度℃ Tears for degree ℃		≤50
适用范围 Application	淡水、海水、污水等 fresh water,sewage,sea water,air

包乘插卡式快速接头(又名：包大头开边抢修器)Baocheng card-plug-intype quick joint (also known as: Baodatou splitting rush repair device)

规格及主要尺寸：mm Specification and main dimension: mm

公称通径DNNominal diameter	L	L	G
80	350	330	1/2
100	400	360	1/2
150	420	380	1/2
200	480	440	3/4
250	480	440	1'
300	510	450	1

Y型管道过滤器 Y type pipe filter

主要性能规范 Main performance specification

型号type	工作压力PN(MPa)WorkingPressuue	试验压力PS（MpaTest pessure PS (Mpa)		适用介质Applicablemedium	适用温度Suitabletemperature
型号type	工作压力PN(MPa)WorkingPressuue	强度Strength	密封Seal	适用介质Applicablemedium	适用温度Suitabletemperature
G141	1.0	1.5	1.1	水	≤150℃
G141	1.0	1.5	1.1	水	≤150℃
G141	1.6	2.4	1.8	水	≤150℃
G141	1.6	2.4	1.8	水	≤150℃

主要尺寸(1.0mpa)Main dimension (1.0mpa)

规格尺寸 typetype	50	65	80	100	125	150	200	250	300
1	170	21	220	285	290	330	480	590	675
H	65	65	165	200	215	260	330	480	500
D	160	180	195	215	245	280	335	390	440
D	125	145	160	180	210	240	295	350	400
T	20	20	22	24	26	26	28	28	28
Z-φ-D	4-18	4-18	8-18	8-18	8-18	8-23	8-23	12-23	12-23

SSLW型滤网伸缩器 SSLW type filter screen expansion bend

技术条件TechnicalConditions

项目公称通径Project DN	1SS80-200
适用介质Applicable mediun	水Water
工作压力Applicable medium	≤1MPa
适用温度Applicable medium	≤110℃
连接方法Applicable mediun	法兰Fl ange

主要性能规范

1×1-50-600水平螺翼式水表由于其本身不带有滤网，在使用中如管道内杂质(如泥沙、水草、水石块等)较多往往使水且停走或影响其快慢。为此必须在水源进口管道上安装”滤水箱”。但是该系列水表由于口径较大，且两端与管道采用法兰连接，为了方便安装及维修水表，一端需要安装伸缩器。

滤网伸缩，是最新设计一物两用，具有结构紧凑，安装尺寸小，重量轻的新型给排水产品。

Main performance specification:

Without filter screen, the 1 1-50-600 horizontal spiral type water meter often become wet with water and stop or affect the speed during its running if there are many impurities (such as sand, water grass and water stone as so on) in the pipe. Therefore, water filter box should be installed on the water inlet pipe. But the caliber of the water meters of this series is large and flange connection is adopted between their two ends and the pipe, so an expansion bend should beinstalledon one end for the convenience of the installation and maintenance of water meter.

Filter screen expansion is à newest type of water supply and drainage product with two functions, compact structure, small installation and light weight.

主要安装数据表Main installation data sheet

DN	1安An	L小Small	L大Large	D	D1	H	d	孔数Holes
50	340	300	360	125	160	90	18	4
80	340	300	360	160	195	105	18	4
100	360	325	390	180	215	112	18	4
150	365	330	400	240	280	145	23	8
200	400	370	460	295	335	175	23	8
250	410	380	470	350	390	205	23	12
300	450	420	510	400	440	230	23	12
400	450	410	550	515	565	295	25	16
500	460	510	650	620	670	345	25	20
600	460	510	650	725	780	350	30	20

Common seamless steel pipe weight table 常用无缝钢管重量表

外径ODmm	壁厚mmThickessmm
	2.5	3	3.5	4	4.5	5	5.5	6	6.5	7	7.5	8	8.5	9			9.5	10
						理论质	量(kg/m)	Theory of	mass (kg/m)
1821	0.961.14	1.111.33	1.251.51	1.381.68	1.501.83	1.601.97	1.702.10	1.782.22	1.842.32	1.902.42	1.942.50	1.972.56	1.992.62	2.002.66			1.992.69	1.972.71
2527	1.39	1.63	1.86	2.07	2.75	2.47	2.64	2.81	2.97	3.11	3.24	3.35	3.46	3.55			3.63	3.70
	1.51	1.78	2.03	2.27	2.50	2.71	2.91	3.11	3.29	3.45	3.61	3.75	3.88	3.99			4.10	4.19
3233	1.821.88	2.152.22	2.262.55	2.762.86	3.653.16	3.333.45	3.593.73	3.853.99	4.094.25	4.324.49	4.534.72	4.73	4.93	5.105.33			5.275.51	5.435.67
												4.93	5.14
3842	2.192.44	2.592.89	2.983.32	3.35	3.72	4.07	4.41	4.73	5.05	5.35	5.64	5.92	6.18	6.44			6.68	6.90
				3.75	4.16	4.56	4.95	5.33	5.69	6.04	6.38	6.71	7.02	7.32			7.61	7.87
4548	2.622.81	3.113.33	3.583.84	4.044.34	4.494.83	4.935.30	5.365.76	5.776.21	6.176.65	6.567.08	6.947.49	7.307.89	7.658.28	7.998.66			8.329.02	8.619.36
5154	2.93	3.483.77	4.014.36	4.544.9.	5.055.49	5.55	6.04	6.51	6.97	7.42	7.86	8.29	8.70	9.10			9.49	9.84
						6.04	6.58	7.10	7.61	8.11	8.60	9.07	9.54	9.99			10.43	10.85
57607073		3.994.22	4.624.88	5.235.52	5.835.16	6.416.78	6.987.39	7.557.99	8.098.58	8.639.15	9.169.71	9.6710.26	10.1710.79	10.6511.32			11.1311.83	11.5912.33
		4.965.18	5.746.00	6.516.81	7.27	8.01	8.75	9.47	10.18	10.88	11.56	12.23	12.89	13.54			14.17	14.80
					7.60	8.38	9.16	9.91	10.66	11.39	12.11	12.82	13.52	14.20			14.88	15.54
7689102108		5.40	6.267.388.50	7.108.38	7.939.38	8.7510.36	9.5611.33	10.3612.28	11.1413.22	11.9114.15	12.6715.07	13.4215.98	14.1516.87	14.8717.76			15.5818.62	16.2819.48
				9.6710.26	10.82	11.96	13.09	14.20	15.31	16.40	17.47	18.54	19.60	20.64			21.67	22.69
					11.49	12.70	13.90	15.09	16.27	17.43	18.59	19.73	20.86	21.97			23.08	24.17
114127133140				10.8512.13	12.1513.59	13.4415.04	14.7216.48	15.9817.90	17.2319.31	18.4820.71	19.7022.10	20.9123.48	22.1124.84	23.3023.19			24.4827.53	25.6528.85
				12.7213.41	14.26	15.78	17.29	18.79	20.28	21.75	23.21	24.66	26.10	27.52			28.93	30.33
					15.04	16.65	18.24	19.83	21.40	22.96	24.51	26.04	27.56	29.07			30.57	32.06
152159168180				14.6015.2916.1817.36	16.3717.14	18.1318.99	19.8720.82	21.6022.64	23.3224.44	25.0326.24	26.7328.02	28.4129.79	30.0831.55	31.7433.29			33.3835.02	35.0236.7438.9641.92
					18.1	4		20.10	22.04	23.97	25.89	27.79	29.68	31.56	33.43				35.29	37.13

					19.48	21.58	23.67	25.75	27.81	29.86	31.90	33.93	35.95	37.95			39.94
194219245273				18.7421.2123.7726.53	21.0323.8026.6929.80	23.3026.39	25.6728.96	27.8231.52	30.0534.06	32.2836.60	34.4939.12	36.6941.63	38.8844.12	41.0646.61			43.2249.08	45.3751.54
						26.5933.04	32.4836.28	35.3639.51	36.2342.72	41.0845.92	43.9349.10	46.76	49.5755.14	52.3858.59			55.1761.73	57.9564.86
												52.28
324325356377				31.5631.66	35.4535.68	39.3339.46	43.2043.33	47.0547.20	50.8951.05	54.7254.89	58.5458.72	62.3462.54	66.1366.34	69.9170.14			73.6873.91	77.4377.67
				34.7236.79	39.0141.34	43.2845.87	47.54	51.79	56.02	60.24	64.46	68.65	72.84	77.01			81.17	85.3290.50
							50.39	54.89	59.39	63.87	68.34	72.80	77.24	81.68			86.09
406426457480				39.6541.63	44.5546.78	49.4451.91	54.3257.03	59.1862.14	64.0467.24	68.8872.33	73.7077.40	78.5282.46	83.3287.51	88.1192.55			92.8997.87	97.65102.59110.23
				4.6846.95	50.2152.77			55.73	61.24	66.73	72.21	77.68	83.14	88.58	94.01	99.43			104.84
						58.57	64.36	70.13	75.90	81.65	87.39	93.12	98.83	104.52			110.22		115.90
508529559				49.7151.7954.74	55.8758.2061.53	62.0264.6168.31	68.1571.00	74.2877.38	80.3983.75	86.4890.11	92.5796.45	98.64102.78	104.70109.39	110.75115.41			116.78121.70	122.81127.99135.38
							75.07	81.82	88.56	95.29	102.00	108.70	115.39	122.07			128.73
610630				59.7861.75	67.1969.41	74.6077.06	81.9984.70	89.3792.33	96.7499.94	104.09107.54	111.43115.13	118.76122.71	126.08130.27	148.00133.39			140.68145.36	147.96152.89

旋转补偿器

旋转补偿器即可以设置在直管段的任意位置进行热补偿，又能利用管线自然转角布置以满足管系热补偿的要求。相对于其他形式的补偿器，旋转补偿器可以减少管系统补偿器的个数及固定支架的设置数量。另外，采用旋转补偿器时，对固定支座无推力，从而降低了土建工程量，节省工程投资，而且在一定程度上简化了管网的设计难度。高温高压自密封旋转补偿器由于使用环境比较恶劣，要求较高，所以本公司按用户提供的技术要求，专门设计制造。材料根据设计温度、压力、介质选用低合金钢无缝钢管或整体锻件及性能优良的耐高温、耐高压、高强度复合密封材料，采用特殊结构、特殊生产工艺及特殊生产技术制造，具有耐高温、耐高压、无推力、自密封、补偿量大、不泄漏等优点。

公称直径	200	250-350	400-450	500-600	700-800	>800
n型组合	≤50°	≤45°	≤40°	≤35°	≤30°	≤25°
o型组合	≤45°

公称直径DNlmml	补偿量axlmm)	接管外径d(mm)	晨大外径Dlmm)	产品长度Limml	转矩MiKa mi
					内压imp a)
					1.0	1.6	2.5	4.0
100	0-1000	108	230	310	0.62	0.96	2.5	2.23
125	0-1000	133	260	310	1.15	2.0	3.13	4.68
150	0-1200	159	285	310	1.81	2.86	4.35	6.97
200	0-1200	219	375	330	2.52	4.10	5.93	9.49
250	0-1500	273	425	360	5.0	7.60	11.61	18.65
300	0-1800	325	480	360	7.61	12.10	17.48	27.56
350	0-1800	377	530	360	9.79	15.85	22.50	36.32
400	0-1800	426	580	360	12.89	20.15	29.84	47.60
450	0-1800	480	630	360	18.20	29.15	42.21	67.52
500	0-1800	530	690	370	24.97	38.96	57.12	91.58
600	0-1800	630	790	370	31.20	50.00	70.23	113.60
700	0-1800	720	910	410	38.12	54.80	86.70	138.50
800	0-1800	820	1015	450	45.90	72.45	105.20	168.30
900	0-1800	920	1130	480	53.60	87.62	124.50	197.00
1000	0-1800	1020	1235	480	62.50	100	145.00	230.00

免维护旋转补偿器

免维护旋转补偿器和其他旋转补偿器产品使用都是靠填料腔内的柔性石墨填进行密封，产品使用过程中每旋转一次，填料就会磨损一点，当磨损量达到一定值时，产品就会出现泄漏。免维护旋转补偿器因在填料压紧法兰上方增加了一组弹簧，当填料出现微量磨损时，依靠压紧弹簧的张力给予补偿，从而延长产品发生泄漏的时间（延后3-5年）。当磨损量超过弹簧张力补偿量时，只需扳紧弹簧压紧法兰上方的螺帽即可，不需要停气修复，运行无次数限制，不易产生泄漏，从而大大提高经济效益。该产品在4.0MPa的压力下补偿5000次不产生泄漏，密封效果优越。

序号	公称直径DNimm	补偿器△(mm)	接管外径	接管外径	长度Limml	租短Mika-m)
序号	公称直径DNimm	补偿器△(mm)	D1imm)	D2(mm)	长度Limml	租短Mika-m)
1	50	0~1000	57	189	380	0.584
2	65	0~1000	76	208	380	0.72
3	80	0~1000	89	233	380	1.11
4	100	0~1000	108	252	380	1.29
5	125	0~1000	133	268	380	1.83
6	150	0~1200	159	303	380	2.35
7	200	0~1200	219	373	400	3.93
8	250	0~1500	273	425	420	8.11
9	300	0~1800	325	477	440	14.48
10	350	0~1800	377	526	460	18.50
11	400	0~1800	426	580	460	25.84
12	450	0~2000	480	630	460	36.21
13	500	0~2000	530	690	480	45.12
14	600	0~2000	630	790	480	63.23
15	700	0~2000	720	890	500	72.70
16	800	0~2000	820	990	500	93.20
17	900	0~2000	920	1090	520	110.50
18	1000	0-2000	1020	1190	520	125.00
19	1100	0~2000	1120	1310	530	145.60
20	1200	0~2000	1220	1410	530	163.70
21	1300	0~2000	1320	1510	540	186.10
22	1400	0~2000	1420	1610	550	202.50
23	1500	0~2000	1520	1710	560	228.70
24	1800	0~2000	1820	2010	560	305.40
25	2000	0~2000	2020	2210	560	305.40

巩义市威力水电设备材料厂

Gongyi Weili Hydroelectric Power Equipment Materials Factory

电话：0371-64031569

传真：0371-64032621

手机：13598027566

地址：河南省巩义市西村工业园区

邮编：451281

网址：http://www.gyweili.com

E-mail:web@gyweili.com

Tel:0371-64031569

Fax: 0371-64032621

Mobile: 13598027566

Address: Gongyi City, Henan Province West Industrial Park

Post Code: 451281

URL:http://www.gyweili.com

E-mail: web@gyweili.com