该页无缩略图
聚合晶硅棒形悬式绝缘子
HDPE Suspension Insulators Modified Polyethylene Suspension Insulators
| 图号 Fig | 1 | 1 | 1 | 2 | |
| 产品型号Catalog | JXBW-10/70-310 | JXBW-35/70-670 | JXBW-66/100-940 | JXBW-110/120-1240 | |
| 绝缘子等级Class | PS70 S16B16-95/350 | PS100 S16B16-230/1015 | PS100 S16B16-410/1920 | PS120 S16B16-550/3150 | |
| 标称额定电压Rated Voltage | 10 | 35 | 66 | 110 | |
| 机械负荷RatedMechanical | 70 | 70 | 100 | 120 | |
| 结构高度 UnitSpacing(mm) | H | 310±10 | 670±10 | 940±15 | 1240±15 |
| 电弧距离Min, ArcingDistance(mm) | h | 158 | 508 | 738 | 1040 |
| 最小公称爬电距 creepageDistance(mm) | 350 | 1015 | 1920 | 3150 | |
| 雷电全波耐受电压DryLighting | 95 | 230 | 410 | 550 | |
| 工频一分钟湿耐受电压wetPower Freq.1minwithstand | 42 | 95 | 185 | 230 | |
聚合晶硅棒形悬式绝缘子的电力配件
End-fittings Suitable for HDPE Suspension insulators
连接金具
configuration of end-fittings
槽型
舌型
耳环型
Y型
根据IEC61466-1所设计的连接金具，可适用于标称电压高于1000V的交流架空线路用绝缘子。 The designation of the above end-fittings are in accordance withIEC61466-1. Polyethylene suspension insulator units for overhead line with a nominal voltage greater than 1000V-Pritl:Standard strength classes and end fittings.
产品目录号定义
Catalog number definition
电缆外径: 8-26mm
最大截面范围：无铠电缆： 3 x 1 6 \mathsf {mm } ^ { 2 } 4 x 1 6 \mathsf {mm } ^ { 2 } 带铠电缆： 3 x 1 0 \mathsf {mm } ^ { 2 } 4 x 1 0 \mathsf {mm } ^ { 2 }
产品尺寸： 1 8 5 x 4 0 x 4 5 0 0 { 1 }
填充重量:150g
电缆外径：14-32mm
最大截面范围：无铠电缆： 3 x 3 5 \mathsf {mm } ^ { 2 } 4 x 2 5 \mathsf {mm } ^ { 2 } 带铠电缆 3 x 1 6 \mathsf {mm } ^ { 2 } 4 x 1 6 \mathsf {mm } ^ { 2 }
产品尺寸： 2 7 0 x 5 5 x 5 5 0 {mm }
填充重量: 3 6 5 { { g } }
电缆外径:23-39mm
最大截面范围：无铠电缆： 3 x 5 0 \mathsf {mm } ^ { 2 } 4 x 5 0 \mathsf {mm } ^ { 2 } 带铠电缆： 3 x 5 0 \mathsf {mm } ^ { 2 } 4 x 3 5 \mathsf {mm } ^ { 2 }
产品尺寸： 3 5 5 x 6 5 x 6 0 {mm }
填充重量:620g
电缆外径:28-50mm
最大截面范围：无铠电缆： 3 x 9 5mm ^ { 2 } 4 x 9 5mm ^ { 2 } 带铠电缆 3 x 9 5mm ^ { 2 } 4 x 7 0 \mathsf {mm } ^ { 2 }
产品尺寸： 4 0 0 x 9 0 x 7 5mm
填充重量:1300g
电缆外径:45-65mm
最大截面范围：无铠电缆： 3 x 2 4 0 \mathsf {mm } ^ { 2 } 4 x 2 4 0 \mathsf {mm } ^ { 2 } 带铠电缆 3 x 2 4 0 \mathsf {mm } ^ { 2 } 4 x 2 4 0 \mathsf {mm } ^ { 2 }
产品尺寸： 4 8 5 x 2 2 0 x 1 8 0 {mm }
填充重量: 6000g
隧道配电接线盒(不截断主缆)IP65
注：电缆护套外径为选型的最终决定因素，导体截面仅作参考。
Note: Outer diameter of cable sheath is the final decision factor for type-choosing, Conductor section is just for reference.
灌胶式电缆直通防水接线盒的安装 Rubber filling type cable through waterproof box installation
7. 按树脂使用说明书配好树脂后，将树脂倒入防水盒中，待树脂表面固化后再盖上盖子。安装完成！
7. Mixed resin according to the instructions for use, pouredresin into the waterproof box, Cover again after the surface ofthe resin curing. Installation complete!
国外单芯电缆分支专用
最大截面范围：主回路： 2 . 5 { - } 3 5 \mathsf {mm } ^ { 2 } 分支回路 : 1 . 5 - 1 0 \mathsf {mm } ^ { 2 }
产品尺寸： 7 0 x 4 5 x 2 8 {mm }
填充重量:30g
最大电缆外径:主回路: 15mm分支回路: 15mm
最大截面范围:主回路： 4 x 1 . 5 - 6 \mathsf { m } \mathsf { m } ^ { 2 } 分支回路： 4 x 1 . 5 { - 4 } \mathsf {mm } ^ { 2 }
产品尺寸： 1 7 5 x 7 5 x 4 0 {mm }
填充重量: \boldsymbol { 1 4 0 } \boldsymbol { \mathfrak { g } }
最大电缆外径：主回路: 29mm分支回路: 22mm
最大截面范围:主回路： 4 x 6 - 1 0 \mathsf {mm } ^ { 2 } 分支回路： 4 x 4 - 1 0 \mathsf {mm } ^ { 2 }
产品尺寸： 1 7 5 x 1 1 0 x 7 6 { {mm } }
填充重量: 500g
最大电缆外径：主回路: 29mm分支回路: 22mm
最大截面范围:主回路： 4 x 1 6 - 2 5mm ^ { 2 } 分支回路： 4 x 6 - 1 6 \mathsf {mm } ^ { 2 }
产品尺寸： 3 0 0 x 1 1 0 x 7 6 { {mm } }
填充重量:1000g
最大电缆外径:主回路: 35mm分支回路: 25mm
最大截面范围：主回路： 4 x 3 5 - 9 5mm ^ { 2 } 分支回路： 4 x 6 - 2 5 \mathsf {mm } ^ { 2 }
产品尺寸： 4 0 0 x 1 2 5 x 1 0 0 {mm }
填充重量:2500g
最大电缆外径:主回路: 65mm分支回路: 56mm
最大截面范围:主回路： 4 x 9 5 - 2 4 0 \mathsf {mm } ^ { 2 } 分支回路： 4 x 6 - 1 5 0 \mathsf {mm } ^ { 2 }
产品尺寸： 4 8 5 x 2 2 0 x 1 8 0 {mm }
填充重量:6000g
最大电缆外径:主回路: 55mm分支回路: 36mm
最大截面范围:主回路： 4 x 3 5 - 1 5 0 {mm } ^ { 2 } 分支回路： 4 x 6 - 7 0 \mathsf {mm } ^ { 2 }
产品尺寸： 2 9 5 x 1 7 5 x 1 3 0 {mm }
填充重量:2000g
注：电缆护套外径为选型的最终决定因素，导体截面仅作参考。
Note: Outer diameter of cable sheath is the final decision factor for type-choosing, Conductor section is just for reference.
附录：绝缘防水密封胶使用说明
Appendix : Instructions forInsulated waterproof sealant
树脂使用方法(请严格遵守，违反如下操作方法所造成的一切后果我方不负责)
The resin used (must be strictly observed, caused by violations of the following HOW-to We are not responsible for any consequences)
1、先将A组份与B组份树脂之间的间隔棒打开，然后充分揉和2-3分钟，直到均匀。
2、立即将混合好的树脂倒入分支盒中，如耽误时间太长容易使树脂稠甚至于固化。
3、应避免皮肤、眼睛与树脂直接接触。
1. Component A and B component resin spacers between the open and full rubbing and 2-3 minutes, until uniform.
2. Immediately poured into the resin mixture into the branch box such asthe delay time is too long to make resin thick and even easier to cure.
3. Should avoid skin and eye direct contact with the resin.
推荐使用本公司生产的绝缘穿刺线夹，安装方便，使用安全不损坏电缆。
Recommend to use our company's insulation piercing Clamps, convenient installation, safe use, no damage to cable.
分支处则将主线和分支电缆裹缠在一起 左右两海绵条之间的尺寸长度应和防水 盒两端密封件之间的尺寸长度相符。 The main line and branch cables are wrapped together where branch location, The length about two sponges conform to the size between waterproof case ends seal.
将海绵分支附件卡入两根电缆 之间，防止漏胶，用扎带进行 固定。 Clip the sponge branch attachment between the two cables, prevent leakage, with the band for fixing.
防水盒合上线卡后，检查一下电缆进出口密封件是否安装正确，并调整至没有明显的缝隙，以防止树脂灌入后漏出防水盒。
After close the clamp of waterproof box, check thecable inlet and outlet seal are installed correctly,and adjust to no obvious gap, to prevent the resinleakage filling in waterproof box.
注意 Note
在确认防水盒正确安装后，按照树脂说明书 调配好，摆正防水盒，倒入树脂，待树脂固 化后就可埋入地下或水下正常运行，安装完毕。 After confirm the waterproof box correct installation, prepare resin then put it into the waterproof box, after the resin curing it can be buried underground or underwater for operation.
此垃圾袋是在安装完毕后，将所有垃圾装入然后丢入垃圾桶。
Put the rubbish into the garbage bag then thrown into the trash can
1、安装时戴好PE手套(随配件一起附送)，如条件允许，可戴上眼镜和口罩。
2、固化时间受环境温度影响，在常温25℃下固化时间为1小时，温度越低，固化时间相应加长；温度越高，固化时间越短。
3、施工现场应保持较好的通风条件。
4、未进行灌浇树脂的置于通风阴凉处，保质期为3个月。树脂不可暴晒，或与其它化学类产品堆置。
5、树脂在灌浇过程中会产一定的气味，但此气味是人体可自行降解，树脂固化后无任何毒性，请放心使用。
6、如不慎入眼，请用大量清水冲洗，并就医治疗。吸入过多导致产生症状，请将患者移到空气新鲜处，如加剧，请就医治疗。
7、灌浇完毕后，将所有使用完的桶、瓶等放入垃圾中并丢弃。
1. The installation wearing PE gloves (together with the accessories included), if available, can wear glasses and masks.
2. The curing time affected by ambient temperature, and cured at 25C for 1 hour, the lower the temperature, curing time extended accordingly; higher the temperature, the shorter the curing time.
3. The construction site should maintain good ventilation conditions.
4. Poured resin have not been placed in the shade.the shelf life of 3 months.Resin is not exposure, or with other chemica Products to push home.
5. The resin poured process will produce a certain smell. but the smell of self-degradation of the human body. the resin cured without any toxicity. Please be assured!
6. If it gets, please rinise with plenty of water, and medical treatment. Inhalation result in symptoms of patients please move to fresh air. such as the intensification of medical treatment, please.
7. After poured, all done with the barrels, bottles and discarded into the garbage.
遂道专用分支防水接线盒Dedicated tunnel branch waterproof junction box
隧道专用分支型防水接线盒，是我司针对隧道电缆安装以及对电缆接头的防水要求，特别研制开发的一种防水盒。本产品考虑到隧道施工环境以及电缆安装位置的复杂性，特别对产品的安装以及电缆接线做了优化设计，使盒子的安装更简单、更利于操作。本型号产品适用于主线小于30毫米，支线小于25毫米的电缆分支接线使用。
根据实际需要用膨胀螺丝将防水盒固定在墙体上。
1kV四芯穿刺连接器（电缆接线环）
1kV Four Core Piercing Connector (Cable Sockets)
1kV及以下四芯穿刺连接器（电缆接线环）选型表
1kV and below four core piercing connector (cable sockets) selection table
| P二 | 主线截面(mm²)Main Section | 支线截面(mm²)Branch Section | ||
| 绞线Strand Cable | 实心导线Solid Core Wire | 绞线Strand Cable | 实心导线Solid Core Wire | |
| SLFC-1 | 50-70 | 70-95 | 6-50 | 6-70 |
| SLFC-2 | 70-120 | 95-150 | 6-50 | 95-150 |
| SLFC-3 | 95-120 | 120-150 | 扇形(Fan-shaped)35-120圆形(Circle)10-95 | 扇形(Fan-shaped)50-150圆形(Circle)16-120 |
| SLFC-4 | 150-185 | 150-240 | 6-70 | 6-70 |
| SLFC-5 | 185-240 6-70 6-70 | |||
应用简介 Usage and cautions
四芯穿刺连接器主要适用于大电流的主干线进行分支用，无需剥除主电缆绝缘层，一个接头就可以同时快速的分支四根支线，且无乎不占用空间，采用铸铝件为外壳，极限强度极高，可重复使用，其整体性能比电缆穿刺分支线夹更加优越。
Four core piercing connector is mainly applied to high current trunk tobranch, the main cable insulation without stripping, one connector can quickly branch to four extension, Almost no space is occupied, the shell ismade of aluminumparts, high ultimate strength, reusable, It is superior than the cable piercing puncture connector.
路灯配电盒介绍Street Lamp distribution box
1、用于路灯系统的保险盒是为了适应实地安装而设计的。
2、保险盒安装在路灯送电网络与灯泡之间。
3、保险盒作为对路灯电路和其它元件的保护装置，在有故障发生时可有选择的切断路灯电路。
1. Insurance box is designed used for street lamp system to fit the field installation.
2. Insurance box is mounted between the lamp power supply network and bulb.
3. Insurance box as a protection device for street lamp circuit and other components, cut off the street lamp circuit selectively when the faults occurs.
路灯配电盒技术说明
Specification for Street Lamp Distribution Box
路灯配电盒壳体是由德国进口的抗曲增加工程塑料制成，内部分支端子全部由铜合金材料加工而成，紧固件由不锈钢丝组成，提供的螺旋型熔断器、小型断路器、保险座均符合相关国家标准，整体产品密封等级为IP43，保护等级Ⅱ级。
Lighting distribution box shell is formed by bending increasedengineering plasticimported from German, internal branch terminals are all made of copper alloy material, fasteners made of stainless steel wire, spiral type miniature, circuit breaker fuse, fuse holder provided arein conformity with the relevant national standards, sealed class is IP43, protection gradeII.
海绵密封块尺寸
路灯配电盒选型标准 Selection Standard
1、适用于路灯灯杆内部接线：灯杆直径≥110mm/灯杆门尺寸≥90\*300mm
2、4个“U”型滑行端子适用于：2线-50mm²3线4-35mm²
3、适用熔断器型号： RLI I-2个最大电流15A RL6 1个最大电流25A RT18 1-3个最大电流32A
4、适用小型断路器型号DZA47-60C32A或其它通用型号比如C65等。
5、定时器或其它客户指定的设备。
1. Suitable for the internal wiring of lamp: pole diameter ≥110mm/ pole gate size≥90\*300mm
2.4 "U" type sliding terminal applies to: 2 lines-50mm² 3 line 4-35mm2
3. Applicable fuse model: RLI I-2 max. current15A RL6 1 max. current 25A RTI8 1-3max. current 32A
4. Suitable for circuit breaker DZA47-60C32A or other common models such as C65.
5. Timer or other customer specified.
设计图样Drawing
· 配装DZ47小型断路器
• 配装 RT18 保险盒
·配装螺旋式熔断器
• Equipped with DZ47miniature circuit breaker
Connection Between Cable & Distribution Board
• Equipped with RT18 insurance box
• Equipped with spiral fuse
示意图样 Schematic Drawing
附注：1、每杆路灯底下一条主电缆，采用一套防水盒及三个SL-25/6穿刺线夹。分支型绝缘防水SL-F5采用抗冲击聚碳酸PC材料，盒内采用绝缘防水密封灌胶密实。防水盒周边回填采用细砂。
Note: 1. Use a waterproof box and three SL-25/6 IPC for a main cable under each street lamp pole, SL-F5 branch type insulated waterproof adopt impact resistance poly carbonate PC material, the box use potted insulating sealing . Waterproof box surrounding backfill with fine sand.
用途Application
适用于配电系统，广泛应用于机场、高速公路、隧道、桥梁、道路和住宅小区等照明配电工程。
Suitable for distributionsystem, widely used in airport, highway, tunnel, bridges, roads and residential areas such as lighting distribution engineering.
技术参数 Technical Parameters
1、电压范围 Voltage range:≤500W
2、工频耐压 Frequency withstand voltage:≥2500V/60s
3、额定电流 Rated current:150A
选型 Model Selection
| 型号 Type | 长×宽×高Length× width ×height |
| SLDZ-4 | $2 2 5 \times 8 8 \times 9 0$ |
| SLDR-4B | $2 2 5 \times 8 8 \times 9 0$ |
| SLDR-4 | $2 2 5 \times 9 5 \times 8 0$ |
| SLDR-2 | $1 4 6 \times 8 5 \times 8 0$ |
安装说明Installation Instructions
打开盒盖，将内六角螺栓旋松，把三相四线电源进线与出线头的绝缘层剥去35mm左右，塞进电源进出线孔，旋紧螺栓，把断路器或熔断器出线端与路灯导线连接，合上盒盖。
Open the cover, loosened the inner six angle bolts, strip about 35mm of the three-phase four - wire power supply inlet wire and insulating layer of wire head, insert the power outlet holes, tighten the bolt, connect outlet terminal of the circuit breaker or fuse with thelamp wire, close the lid.
注：SLDR-4B、SLDR-4、SLDR-2等路灯配电盒安装结构图均可参照上图。
Note: SLDR-4B,SLDR-4,SLDR-2 street lighting distribution box installation structure diagram according to the above.
跌落式熔断器
www.chinaziyong.com
Just to CLICK here: We will provide you with the best service
溫州自勇电气有限公司
WENZHOU ZIYONG ELECTRICAL CO.,LTD
电话：+8613868882126 0577-61985638 0577-62530693
网址：www.chinaziyong.commade-in-china.com
E-mail: kz@chinaziyong.com
地址：中国浙江省乐清市柳市镇
Mobile:+8613868882126 0577-61985638 0577-62530693
Web: www.chinaziyong.com made-in-china.com E-mail: kz@chinaziyong.com
Address: Liushi town, Yueqing City, Zhejiang Province, China [325600]
