2025年Gesac车刀目录 - 电子画册在线预览、各类电子画册在线制作-云展网平台

PCD Turning Insert (Positive)

Diamond 35° with Hole

Order No.
		Teeth	Dimensions(mm)					PCDGrade
		Teeth	LE	IC	S	D1	RE	DN5P
		VCGW110302GB-1	1	3	6.35	3.18	2.8	0.2	O
		VCGW110304GB-1	1	3	6.35	3.18	2.8	0.4	●
		VCGW160402GB-1	1	3	9.525	4.76	4.4	0.2	O
		VCGW160404GB-1	1	3	9.525	4.76	4.4	0.4	●
		VCGW160408GB-1	1	3	9.525	4.76	4.4	0.8	O
		VCGW110302KB-1	1	3	6.35	3.18	2.8	0.2	O
	VCGW110304KB-1	1	3	6.35	3.18	2.8	0.4	●
	VCGW160402KB-1	1	3	9.525	4.76	4.4	0.2	O
	VCGW160404KB-1	1	3	9.525	4.76	4.4	0.4	●
	VCGW160408KB-1	1	3	9.525	4.76	4.4	0.8	O
	VCGT110302K-1DNF	1	3.5	6.35	3.18	2.8	0.2	O
	VCGT110304K-1DNF	1	3.5	6.35	3.18	2.8	0.4	O
	VCGT160404K-1DNF	1	3.5	9.525	4.76	4.4	0.4	●
	VCGT160408K-1DNF	1	3.5	9.525	4.76	4.4	0.8	●
	VCGT160412K-1DNF	1	3.5	9.525	4.76	4.4	1.2	O
	VCGT110304K-1DNM	1	3.5	6.35	3.18	2.8	0.4	O
	VCGT160404K-1DNM	1	3.5	9.525	4.76	4.4	0.4
	VCGT160408K-1DNM	1	3.5	9.525	4.76	4.4	0.8	●
	VCGT160412K-1DNM	1	3.5	9.525	4.76	4.4	1.2	O

Stock OAvailable Upon Order

Circle 360° with Hole

●Stock OAvailable Upon Order

Order No.RDEW080300GN-1	Teeth	Dimensions(mm)			PCD Grade
	Teeth	IC	S	D1	DN25P
	1	8	3.18	2.94	O
	RDEW100300GN-1	1	10	3.18	4.6	●
	RDEW120400GN-1	1	12	4.76	4.4	O
	RDEW160400GN-1	1	16	4.76	5.5	●

Recommended Cutting Data PCBN Cutting Tools

ISO		WorkpieceMaterial	Hardness	Cutting Range	WorkingCondition	Grade	Lower Limit-recommended-upper Limit
ISO		WorkpieceMaterial	Hardness	Cutting Range	WorkingCondition	Grade	Cutting SpeedVc (m/min)	Cutting Depthap (mm)	Feedf(mm/rev)
K		Nodular CastIron	QT450~QT700	Finishing	General	BKC120P	150-300-500	0.10-0.20-0.50	0.05-0.12-0.3
		Alloy CastIron	≥HB200	Finishing	General	BKN115P	200-400-800	0.05-0.20-0.50	0.05-0.20-0.40
		Gray Cast Iron	HB200~230	Finishing	General	BKN115P	400-600-1500	0.05-0.20-0.50	0.05-0.20-0.40
		Gray Cast Iron	HB200~230	Finishing-roughing	General	BKN225ZBKN225S	400-600-1200	0.05-0.30-0.50	0.05-0.20-0.50
	S	PowderMetallurgy	HRB50~90	Finishing	Continuous	BSN115P	50-150-300	0.05-0.20-0.50	0.05-0.12-0.30
H		High-hard-ness Material	≥HRC50	Finishing	Continuous	BHC115P	120-150-220	0.05-0.10-0.20	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-roughing	General	BHC125P	100-130-180	0.05-0.10-0.50	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-semi-finishing	Interrupted	BHC135P	80-100-150	0.05-0.10-0.40	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-semi-finishing	Continuous	BHC210P	100-150-260	0.05-0.10-0.20	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-semi-finishing	Continuous	BHC215Z	120-150-230	0.05-0.10-0.20	0.05-0.10-0.15
		High-hard-ness Material	≥HRC50	Finishing-roughing	General	BHC225P	100-140-200	0.05-0.10-0.50	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-roughing	General	BHC225Z	100-140-200	0.05-0.10-0.50	0.05-0.10-0.20
		High-hard-ness Material	≥HRC50	Finishing-roughing	General	BHN225S	100-150-190	0.05-0.10-0.50	0.05-0.10-0.20

PCBN Chip Breaker Insert

ISO	WorkpieceMaterial	Hardness	CuttingRange	Pur-pose	Geome-try	Grade	Lower Limit-recommended-upper Limit
ISO	WorkpieceMaterial	Hardness	CuttingRange	Pur-pose	Geome-try	Grade	Cutting SpeedVc (m/min)	Cutting Depthap (mm)	Feedf(mm/rev)
H	High-hardnessMaterial	≥HRC50	Finishing	Contin-uous	BHF	BHC210P	120-160-260	0.10-0.20-0.30	0.05-0.10-0.25
	High-hardnessMaterial	≥HRC50	Semi-finishing	General	BHF	BHC225P	100-150-200	0.10-0.20-0.30	0.05-0.10-0.25
	High-hardnessMaterial	≥HRC50	Finishing	Contin-uous	BHM	BHC210P	110-140-220	0.30-0.50-0.70	0.10-0.20-0.30
	High-hardnessMaterial	≥HRC50	Semi-finishing	General	BHM	BHC225P	100-120-180	0.30-0.50-0.70	0.10-0.20-0.30

Recommended Cutting Data PCD Cutting Tools

ISO	WorkpieceMaterial	Cutting Range	WorkingCondition	Grade	Lower Limit-recommended-upper Limit
ISO	WorkpieceMaterial	Cutting Range	WorkingCondition	Grade	Cutting SpeedVc (m/min)	Cutting Depthap (mm)	Feedf(mm/rev)
	AluminumAlloy	Finishing	General	DNN125P	300-1200-3000	0.05-0.20-0.50	0.05-0.10-0.20
	Copper Alloy	Finishing	General	DNN125P	200-500-1000	0.05-0.40-2.00	0.05-0.10-0.20
	Plastic	Finishing	General	DNN125P	100-600-1000	0.10-0.40-2.00	0.05-0.10-0.40
	Wood, Inor-ganic Board	Finishing	General	DNN125P	200-2000-4000	0.10-0.50-2.00	0.05-0.10-0.40
	CementedCarbide	Finishing	General	DNN125P	10-20-30	0.05-0.20-0.50	0.05-0.10-0.20
	Graphite	Finishing	General	DNN125P	100-300-600	0.10-0.40-2.00	0.10-0.25-1.00

PCBN Chip Breaker Insert

ISO	WorkpieceMaterial	Cutting Range	WorkingCondition	Grade	Lower Limit-recommended-upper Limit
ISO	WorkpieceMaterial	Cutting Range	WorkingCondition	Grade	Cutting SpeedVc (m/min)	Cutting Depthap (mm)	Feedf(mm/rev)
	AluminumAlloy	Finishing	General	DNN125P	300-1200-3000	0.05-0.20-0.50	0.05-0.10-0.20
	Copper Alloy	Finishing	General	DNN125P	200-500-1000	0.05-0.40-2.00	0.05-0.10-0.20
	Plastic	Finishing	General	DNN125P	100-600-1000	0.10-0.40-2.00	0.05-0.10-0.40
	Wood, Inor-ganic Board	Finishing	General	DNN125P	200-2000-4000	0.10-0.50-2.00	0.05-0.10-0.40
	CementedCarbide	Finishing	General	DNN125P	10-20-30	0.05-0.20-0.50	0.05-0.10-0.20
	Graphite	Finishing	General	DNN125P	100-300-600	0.10-0.40-2.00	0.10-0.25-1.00

List of Turning Tool Holders

MCBNR/L	MCLNR/L		MDJNR/L	MDPNN	MDQNR/L
P158	P158			P160DMTENN MTFNR/LP162 P162MVQNR/L MWLNR/LP164 P165PSBNR/L PSSNR/L
MSBNR/LP160MTGNR/L
						MSKNR/L


P163	P163

PCBNR/L	PCLNR/L
P165	P166		P167			P168	P169
	0
PRDCN	PTGNR/L		PWLNR/L		DCLNR/L-HPC	SDUCR/L-HPC
P170	P171		P171	P172	P172
			0
			DVJNR/L-HPC	DWLNR/L-HPC
P173	P173

		SDJCR/L		SSDCN	STGCR/L	SVJCR/L
P174	P174		P175	P175	P176
	书

List of Turning Tool Holders

SWLCR/L	SCLCR/L	SCLCR/L-A16	SCKCR/L	SDUCR/L
P177	P180	P182	P182	P183

SDQCR/L	SDXCR/L	SSKCR/L	STUCR/L	STWCR/L
P184	P185	P185	P186	P186

STFCR/L	SVUCR/L	SWLCR/L	SCLPR/L	STFPR/L
P187	P188	P189	P189	P190

Type Representation Rules for External Diameter Turning Tool Holders

③

④

⑤

① Clamping Mechanism

D	Double ClampingType
M	Wedge Locking TypeDouble ClampingType for HeavyCutting
P	Lever Locking Type
S	Screw ClampingType

④ Insert Relief Angle

B	5°
C	7°
D	$1 5 ^ { \circ }$
E	$2 0 ^ { \circ }$
N	$0 ^ { \circ }$
P	$1 1 ^ { \circ }$

② Insert Shape


		Diamond
D	$5 5 ^ { \circ }$ Diamond
R	Circular
S	Square
T	RegularTriangle
V	35°Diamond
W	Hexagon
X	SpecialShape

⑤ Cutting Direction

R
R
L
N

③ Tool Cutting Edge Angle
A
B
D
E
F
G
J
K
L
P
Q
S
V

⑥ Tool Height

Code	Height
08	8
10	10
12	12
16	16
20	20
25	25
32	32

⑦ Tool Width
Code	Width
08	8
10	10
12	12
16	16
20	20
25	25
32	32

⑧ Tool Length
Code	Width
E	70
F	80
H	100
K	125
M	150
P	170
Q	180
R	200

⑨ Cutting Edge Length (mm)
Inscribed Circle
6.35	06	07	=	06	11	11	04
9.525	09	11	-	09	16	16	06
12.7	12	15	1	12	22	-	08
15.875	16	-	-	15	-	-	-
19.05	19	1	-	19	-	-	-
25.4	25	-	-	25		-	–
32	-	-	32	-		1	1

External Diameter Turning Tool Holder (Negative)

MCBNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

Weight

InStock

OHX

Insert

MCBNR/L2020K12

2020125

32 2017CN**1204**DCN1204MH SPM060170H CAM02H

SD-M060200H

TH25LHTH30LH

0.4

MCBNR/L2525M12

150

CN**1204**

DCN1204MH

SPM060170H

CAM02H

SD-M060250H

TH25LHTH30LH

0.78

MCBNR/L3232P12

32170

CN**1204**

DCN1204MH S

PM060170H

CAM02H

SD-M060280H

TH25LHTH30LH

1.37

MCBNR/L2525M16

25150

CN**1606**

DCN1604MH

SPM-080220FH

CAM03H

SD-M060250H

TH30LH

0.78

MCBNR/L3232P19

32170 42 3227

CN**1906**

SPM-DCN1904MH100240FH

CAM05H

SDM-080350FH

TH40LH 1.37

StockOAvailable Upon Order

MCLNR/L

Order No.	Dimensions (mm)						Matched	Shim	Pin	ClampPlate	Stud	Wrench	(KG)	InStock
Order No.	H	B	LF	OHX	HF	WF	Insert			07				R	L
MCLNR/L2020K12	20	20	125	32	20	25CN1204DCN1204MHSPM060170HCAM02H S					TH25LHDM060200HTH30LH		0.4
MCLNR/L2525M12	25	25	150	32	25	32	CN1204	DCN1204MH	SPM060170H	CAM02H	SDM060250H	TH25LHTH30LH	0.78
MCLNR/L3232P12	32	32	170	32	32	40	CN1204	DCN1204MH	SPM060170H	CAM02H	SDM060280H	TH25LHTH30LH	1.37
MCLNR/L2525M16	25	25	150	38	25	32	CN1606	DCN1604MH	SPM-080220FH	CAM03H	SDM060250H	TH30LH	0.78
MCLNR/L3232P16	32	32	170	38	32	40	CN1606	DCN1604MH	SPM-080220FH	CAM03H	SDM060280H	TH30LH	1.37
MCLNR/L3232P19	32	32	170	42	32	40	CN1906	DCN1904MH	SPM-100240FH	CAM05H	SDM-080350FH	TH40LH	1.37

External Diameter Turning Tool Holder (Negative)

MDJNR/L

●StockOAvailable Upon Order

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

(KG)

InStock

OHX

Insert

R L

MDJNR/L2020K11

125

DN**1104**

DDN1103MH SPM050130H CAM02H

SD-M060200H

TH20LHTH30LH

0.4

MDJNR/L2020K1504

125

DN**1504**

DDN1504MH

SPM060170H

CAM03H

SD-M060200H

TH25LHTH30LH

0.4

MDJNR/L2525M1504

150

DN**1504**

DDN1504MH S

PM060170H

CAM03H

SD-M060250H

TH25LHTH30LH

0.78

MDJNR/L2525M1506

150

DN**1506**

DDN1504MH S

PM060190H

CAM03H

SD-M060250H

TH25LHTH30LH

0.78

MDJNR/L3232P1506

170

DN**1506**

DDN1504MH S

PM060190H

CAM03H

SD-M060280H

TH25LH1.37TH30LH

MDPNN

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

(KG)

OHX

Insert

厂

Stock

MDPNN2020K11

2020125

20 10

DN**1104** DDN1103MH SPM050130H CAM02H

SD-M060200H

TH20LHTH30LH

0.38

●

MDPNN2020K1504

125

DN**1504**

DDN1504MH

SPM060170H C

AM03H

SD-M060200H

TH25LHTH30LH

0.38

●

MDPNN2525M1504

150

251

2.5

DN**1504**

DDN1504MH S

PM060170H C

AM03H

SD-M060250H

TH25LHTH30LH

0.76

●

MDPNN2525M1506

150

12.5

DN**1506**

DDN1504MH S

PM060190H C

AM03H

SD-M060250H

TH25LHTH30LH

0.76

●

MDPNN3232P1506

170 42

DN**1506**

DDN1504MH SPM060190H CAM03H

SD-M060280H

TH25LH1.35TH30LH

●

●Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

MDQNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

(KG)

InStock

OHX

Insert

MDQNR/L2020K11

125

DN**1104**

DDN1103MH SPM050130H C

AM02H

SDM060200H

TH20LHTH30LH

0.4

MDQNR/L2020K1504

125

DN**1504**

DDN1504MH S

PM060170H

CAM03H S

DM060200H

TH25LHTH30LH

0.4

MDQNR/L2525M1504

150

DN**1504**

DDN1504MH S

PM060170H C

AM03H

SDM060250H

TH25LHTH30LH

0.78

MDQNR/L3232P1506

170

DN**1506**

DDN1504MH S

PM060190H C

AM03H S

DM060280H

TH25LHTH30LH

1.37

●StockOAvailable Upon Order

MSBNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

InStock

OHX

Insert

MSBNR/L2020K12

125

2017SN**1204**DSN1204MHS

PM060170HCAM02HS

DM060200H

TH25LH0.4TH30LH

MSBNR/L2525M12

150

SN**1204**

DSN1204MH

SPM060170HCAM02H

SDM060250H

TH25LHTH30LH

0.78

MSBNR/L3232P12

170

SN**1204**

DSN1204MH

SPM060170HCAM02H

SDM060280H

TH25LHTH30LH

1.37

MSBNR/L2525M15

150

SN**1506**

DSN1504MH

SPM-080220FH

CAM03H

SDM060250H

TH30LH

0.78

MSBNR/L3232P19

170

SN**1906**

DSN1904MH

SPM-100240FH

CAM05H

SDM-080350FH

TH40LH1.37

●StockOAvailable Upon Order

MSKNR/L

Order No.

Dimensions (mm)

MatchedInsert

Shim

ClampPlate

Stud

Wrench

In Stock

OHX

WeightGAT

MSKNR/L2020K12

2020125

35 2025SN**1204**DSN1204MH SPM060170H CAM02H

SD-M060200H

TH25LHTH30LH

0.4

●

MSKNR/L2525M12

150

SN**1204**

DSN1204MH

SPM060170HC

AM02H

SD-M060250H

TH25LHTH30LH

0.78

MSKNR/L3232P12

32170

35 32

SN**1204**

DSN1204MHS

PM060170H CAM02H

SD-M060280H

TH25LHTH30LH

1.37

MSKNR/L2525M15

150

SN**1506**

DSN1504MH

SPM-080220FH

CAM03H

SD-M060250H

TH30LH

0.78

MSKNR/L3232P19

32170

48 32

SN**1906**

DSN1904MH

SPM-100240FH

CAM05H

SDM-080350FH

TH40LH

1.37

●StockOAvailable Upon Order

MSSNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

InStock

OHX

Insert

MSSNR/L2020K12

125

32 2025SN**1204**

DSN1204MH SPM060170H CAM02H

SD-M060200H

TH25LHTH30LH

0.39

MSSNR/L2525M12

150

SN**1204**

DSN1204MH

SPM060170HC

AM02H

SD-M060250H

TH25LHTH30LH

0.77

MSSNR/L3232P12

170

SN**1204**

DSN1204MH S

PM060170H

CAM02H

SD-M060280H

TH25LHTH30LH

1.36

MSSNR/L2525M15

150

SN**1506**

DSN1504MH

SPM-080220FH

CAM03H

SD-M060250H

TH30LH

0.77

MSSNR/L3232P19

170

40 S

N**1906**

DSN1904MH

SPM-100240FH

CAM05H

SDM-080350FH

TH40LH 1.36

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

MTENN

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

Weight

OHX

Insert

(KG)

Stock

MTENN2020K16

125

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD- TH20LHM060200H TH30LH

0.38

●

MTENN2525M16

150

251

2.5

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD-M060250H

TH20LHTH30LH

0.76

MTENN3232P16

170

32 16

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD-M060280H

TH20LHTH30LH

1.35

MTENN3232P22

170

TN**2204**

DTN2204MH

SP-M060170H

CAM02H

SD-M060280H

TH25L HTH30LH

1.35

●StockOAvailable Upon Order

MTFNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

(KG)

InStock

OHX

Insert

「

MTFNR/L2020K16

20 2

0 125

32 20 25TN**1604**DTN1603MH

SP- SD-CAM02HM050130H M060250H

TH20LHTH30LH

0.4

MTFNR/L2525M16

150

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD-M060250H

TH20LHTH30LH

0.78

MTFNR/L3232P16

32 3

2 170

3232

TN**1604**

DTN1603MH

SP-CAM02HM050130H

SD-M060280H

TH20LHTH30LH

1.37

MTFNR/L3232P22

170

TN**2204**

DTN2204MH

SP-CAM02HM060170H

SD-M060280H

TH25L HTH30LH

1.37

StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

MTGNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

InStock

OHX

Insert

MTGNR/L2020K16

125

TN**1604**

DTN1603MH S

PM050130H C

AM02H

SD-M060250H

TH20LHTH30LH

0.4

MTGNR/L2525M16

150

TN**1604**

DTN1603MH

SPM050130H

CAM02H

SD-M060250H

TH20LHTH30LH

0.78

MTGNR/L3232P16

170

TN**1604**

DTN1603MH S

PM050130H

CAM02H

SD-M060280H

TH20LHTH30LH

1.37

MTGNR/L3232P22

32170

TN**2204**

DTN2204MH S

PM060170H C

AM02H

SD-M060280H

TH25LH1.37TH30LH

StockOAvailable Upon Order

MTJNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

(KG)

InStock

OHX

Insert

MTJNR/L2020K16

125

2025

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD- TH20LHM060250H TH30LH

0.4

MTJNR/L2525M16

150

TN**1604**

DTN1603MH

SP-M050130H

CAM02H

SD-M060250H

TH20LHTH30LH

0.78

MTJNR/L3232P16

170

32 4

0 T

N**1604**

DTN1603MH

SP-M050130H

CAM02H

SD-M060280H

TH20LHTH30LH

1.37

MTJNR/L3232P22

170

TN**2204**

DTN2204MH

SP-M060170H

CAM02H

SD-M060280H

TH25LHTH30LH

1.37

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

MVJNR/L

Order No.

Dimensions (mm)

Matched

Shim

ClampPlate

Stud

Wrench

InStock

OHX

Insert

可

MVJNR/L2020K16 2020 125 45 20 25 VN**1604**DVN1603MH

SP- SD- TH20LHCAM04HM050130H M060200H TH30LH

0.4

MVJNR/L2525M16

150

32V

N**1604**

DVN1603MH

SP-M050130H

CAM04H

SD-M060250H

TH20LHTH30LH

0.78

MVJNR/L3232P16

32 32 170

45 32 40 VN**1604**

SP-DVN1603MH CAM04HM050130H

SD- TH20LHM060280H TH30LH

1.37

●StockOAvailable Upon Order

MVQNR/L

Order No.

Dimensions (mm)

Matched Insert

Shim

Clamp Plate

Stud

Wrench

Weight (KG)

In Stock R L

B LF

OHX HF WF

MVQNR/L2020K16

20 125

20 25

VN**1604**

DVN1603MH

SP-

CAM02H

SD-

TH20LH

0.4

MVQNR/L2525M16

25 150

25 32

VN**1604**

DVN1603MH

M050130H SP- M050130H

CAM03H

M060200H SD-

TH30LH TH20LH TH30LH

0.78

MVQNR/L3232P16

32 32

170

32 40

VN**1604**

DVN1603MH

SP- M050130H

CAM03H

M060250H SD- M060280H

TH20LH TH30LH

1.37

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

MWLNR/L

Order No.	Dimensions (mm)						MatchedInsert
Order No.	H	B	LF	OHX	HF	WF	MatchedInsert
MWLNR/L2525M06T3	2525		5150	28 25		532 WN06T3
MWLNR/L2020K0604	20	20	125	28	20	25	WN0604
MWLNR2525M0604	20	20	150	28	25 3	2 W	N0604
MWLNR/L2020K08	20	20	125	32	20	25	WN0804
MWLNR/L2525M08	25	25	150	35	25	32	WN0804
MWLNR/L3232P08	32	32	170	35	32	40	WN0804

●Stock OAvailable Upon Order

Shim	Pin	ClampPlate	Stud	Wrench	Weight	InStock
				厂	(KG)	R	L
DWN-0603MH	SP-M050130H	CAM01H	SD-M050200H	TH20LH0.78TH25LH
DWN-0603MH	SP-M050130H	CAM01H	SD-M050200H	TH20LHTH25LH	0.4
DWN-0603MH	SP-M050130H	CAM01H	SD-M050200H	TH20LHTH25LH	0.78
DWN-0804MH	SP-M060170H	CAM02H	SD-M060250H	TH25LHTH30LH	0.4
DWN-0804MH	SP-M060170H	CAM02H	SD-M060250H	TH25LHTH30LH	0.4
DWN-0804MH	SP-M060170H	CAM02H	SD-M060280H	TH25LHTH30LH	1.37

PCBNR/L

Order No.	Dimensions (mm)						Matched	Shim	Dowel Pin	Leverr	Lever Screw Wrench	h	(KG)	InStock
Order No.	H	B	LF	OHX	HF	WF	Insert				-			R	L
PCBNR/L2020K12	20 20 1		25	30	20	17	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD TH30LD		0.4	O
PCBNR/L2525M12	25	25	150	26	25	22	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.78		O
PCBNR/L3232P12	32	32	170	27	32	29	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.37	O
PCBNR/L2525M16	25	25	150	32	25	22	CN1606	DCN1604PD	PA5D	LA5D	SLM080250FD	TH30LD	0.78	●	O
PCBNR/L3232P16	32	32	170	33	32	27	CN1606	DCN1604PD	PA5D	LA5D	SLM080250FD	TH30LD	1.37	O
PCBNR/L3232P19	32	32	170	38	32	27	CN1906	DCN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	1.37		O
PCBNR/L4040S19	404	0 2	50	38	40	35	CN1906	DCN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	3.2	O
PCBNR/L4040S2509	40	40	250	50	40	37	CN2509	DCN2504PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2	O

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PCLNR/L

Order No.	Dimensions (mm)						Matched	Shim	Dowel Pin	Leverr	Lever Screw Wrench	h		InStock
Order No.	H	B	LF	OHX	HF	WF	Insert			R	-C			R	L
PCLNR/L2020K12	20	20	125	28	20	26	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.4	O
PCLNR/L2525M12	25	25	150	28	25	32	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.78	O
PCLNR/L3225P12	32	25	25 170	32	32	32	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.09	O
PCLNR/L3232P12	32	32	170	32	32	39	CN1204	DCN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.37	O
PCLNR/L2525M16	25	25	150	36	25	32	CN1606	DCN1604PD	PA5D	LA5D	SLM080250FD	TH30LD	0.78	O
PCLNR/L3225P16	32	25	170	36	32	32	CN1606	DCN1604PD	PA5D	LA5D	SLM080250FD	TH30LD	1.09	O
PCLNR/L3232P16	32	32	32 170	36	32	39	CN1606	DCN1604PD	PA5D	LA5D	SLM080250FD	TH30LD	1.37	O
PCLNR/L3232P19	32	32	170	40	32	40	CN1906	DCN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	1.37	O
PCLNR/L4040S19	40	40	250	40	40	49	CN1906	DCN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	3.2	O
PCLNR/L4040S2509	40	40	250	47	40	50	CN2509	DCN2504PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2	O
PCLNR/L4040S2509											SLM120360FD	TH50LD	3.2	O

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PDJNR/L

Order No.	Dimensions (mm)						Matched	Shim	Dowel Pin	Leverr	Lever Screw	Wrench h		InStock
	H	B	LF	OHX	HF	WF	Insert				-			R	L
PDJNR/L2020K11	20 2	0 125		25	20	25	DN1104	DDN11T2PD	PA3D	LA3D	SLM060130D	TH25LD	0.38	O
PDJNR/L2525M11	25	25	150	30	25	30	DN1104	DDN11T2PD	PA3D	LA3D	SLM060130D	TH25LD	0.78		O
PDJNR/L2020K1506	20	20	125	32	20	25	DN1506	DDN1503PD	PA4D	LA4BD	SLM080250FD	TH30LD	0.38	O
PDJNR/L2525M1506	25	25	150	35	25	32	DN1506	DDN1503PD	PA4D	LA4BD	SLM080250FD	TH30LD	0.78		O

PDJNR/L3225P1506	32	25	170	35	32	32	DN1506					TH30LD	1.09	O
								DDN1503PD	PA4D	LA4BD	SLM080250FD
PDJNR/L3232P1506	32	32	170	35	32	38	DN1506		PA4D	LA4BD		TH30LD	1.37		O
								DDN1503PD			SLM080250FD
PDJNR/L2020K1504	20	20	20 125	35	20	25	DN1504
										LA4D
												TH30LD	0.4	O
								DDN1503PD	PA4D		SLM080210FD
PDJNR/L2525M1504	25	25	150	35	25	32	DN1504						0.78		O
								DDN1503PD	PA4D	LA4D	SLM080210FD	TH30LD
PDJNR/L3232P1504
	32	32	170	35	32	38	DN1504	DDN1503PD	PA4D	LA4D	SLM080210FD	TH30LD	1.37

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PSBNR/L

Order No.	Dimensions (mm)						Matched	Shim	Dowel Pin	Leverr	Lever Screw	Wrench h	(KG)	InStock
Order No.	H	B	LF	OHX	HF	WF	Insert			A		I		R	L
PSBNR/L2020K12	20	20	125	28	20	17	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.4	O
PSBNR/L2525M12	25	25	25 150	28	25	22	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.78	O
PSBNR/L3225P12	32	25	170	28	32	22	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.09	O
PSBNR/L3232P12	32	32	32 170	28	32	29	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.37	O
PSBNR/L2525M15	25	25	25 150	32	25	22	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	0.78	O
PSBNR/L3225P15	32	25	170	32	32	22	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	1.09	O
PSBNR/L3232P15	32	32	170	32	32	28	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	1.37	O
PSBNR/L3232P19	32	32	170	45	32	36	SN1906	DSN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	1.37	O
PSBNR/L4040S19	40	40	40 250	45	40	35	SN1906	DSN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	3.2	O
PSBNR/L4040S2507	40	40	250	50	40	35	SN2507	DSN2506PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2		O
PSBNR/L4040S2509	40	40	250	50	40	35	SN2509	DSN2504PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2	●o

StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PSSNR/L

Order No.	Dimensions (mm)						Matched	Shim	Dowel Pin	Leverr	Lever Screw Wrench	h	(KG)	InStock
Order No.	H	B	LF	OHX	HF	WF	Insert			A	-	厂		R	L
PSSNR/L2020K12	20	20	125	28	20	25	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.4	O
PSSNR/L2525M12	25	25	150	32	25	30	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	0.78	O
PSSNR/L3225P12	32	25	170	32	32	30	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.09	O
PSSNR/L3232P12	32	32	170	32	32	38	SN1204	DSN1203PD	PA4D	LA4D	SLM080210FD	TH30LD	1.37		O
PSSNR/L2525M15	25	25	150	35	25	30	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	0.78	O
PSSNR/L3225P15	32	25	170	35	32	30	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	1.09	O
PSSNR/L3232P15	32	32	170	35	32	38	SN1506	DSN1504PD	PA5D	LA5D	SLM080250FD	TH30LD	1.37	O
PSSNR/L3232P19	32	32	170	40	32	38	SN1906	DSN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	1.37	O
PSSNR/L4040S19	40	40	40 250	50	40	48	SN1906	DSN1904PD	PA6D	LA6D	SLM100270FD	TH40LD	3.2	O
PSSNR/L4040S2507	40	402	50	50	40	48	SN2507	DSN2506PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2		O
PSSNR/L4040S2509	40	40	40 250	50	40	48	SN2509	DSN2504PD	PA8D	LA8D	SLM120360FD	TH50LD	3.2	O

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PRDCN

Order No.	Dimensions (mm)						Matched	Shim	DowelPin	Lever r	Lever Screw	Wrench h		In
Order No.	H	B	LF	OHX	HF	WF	Insert				-C			Stock
PRDCN2525M16	25	25	25 150	35	25	10	RCMX1606**	DRN1604PD	PA4D	LCL16CD	SLM060210D	TH25LD	0.78
PRDCN3232P16	32	32	170	32	32	16	RCMX1606**	DRN1604PD	PA4D	LCL16CD	SLM060210D	TH25LD	1.37	●
PRDCN3232P20	32	32	32 170	40	32	16	RCMX2006**	DRN2004PD	PA5D	LCL20CD	SLM080250FD	TH30LD	1.37
PRDCN4040S20	40	40	250	45	40	20	RCMX2006**	DRN2004PD	PA5D	LCL20CD	SLM080250FD	TH30LD	1.37
PRDCN3232P25	32	32	170	45	32	16	RCMX2507**	DRN2506PD	PA6D	LCL25CD	SLM100300FD	TH40LD	1.37
PRDCN4040S25	40	40	250	50	40	20	RCMX2507**	DRN2506PD	PA6D	LCL25CD	SLM100300FD	TH40LD	3.2	•

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

PTGNR/L

Stock OAvailable Upon Order

Order No.

Dimensions (mm)

Matched

Shim

Dowel Pin

Leverr

Lever Screw Wrench

InStock

OHX HF

Insert

-C

PTGNR/L2020K16

20 20 125

TN**1604** DTN16T2PD PA3D

LA3D

SLM060170D

TH25LD

0.4

PTGNR/L2525M16

150

TN**1604**

DTN16T2PD

PA3D

LA3D

SLM060170D

TH25LD

0.78

PTGNR/L3225P16

25170

TN**1604**

DTN16T2PD

PA3D

LA3D

SLM060170D

TH25LD

1.09

PTGNR/L3232P16

170

TN**1604**

DTN16T2PD

PA3D

LA3D

SLM060170D

TH25LD

1.37

●

PTGNR/L2525M22

25150

TN**2204**

DTN2203PD

PA4D

LA4D

SLM080210FD

TH30LD

0.78

PTGNR/L3225P22

170

TN**2204**

DTN2203PD

PA4D

LA4D

SLM080210FD

TH30LD

1.09

PTGNR/L3232P22

32 32170

TN**2204**

DTN2203PD

PA4D LA4D

SLM080210FD

TH30LD 1.37 O

PWLNR/L

Order No.

Dimensions (mm)

Matched

Shim

DowelPin

Leverr

Lever Screw

Wrenchh

(KG)

InStock

OHX

Insert

-C

PWLNR/L2020K0604

2020125

25 2023WN**0604**DWN06T2PD

PA3D

LA3D

SLM060170D

TH25LD

0.4

PWLNR/L2525M0604

150

WN**0604**

DWN06T2PD

PA3D

LA3D

SLM060170D

TH25LD

0.78

PWLNR/L2020K08

20 20 125

WN**0804**

DWN0803PD

PA4D

LA4D

SLM080210FD

TH30LD

0.4

PWLNR/L2525M08

150

WN**0804**

DWN0803PD

PA4D

LA4D

SLM080210FD

TH30LD

0.78

PWLNR/L3232P08

32 32170 26 3237WN**0804**DWN0803PD PA4D LA4D

SLM080210FD

TH30LD 1.37 O

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

DCLNR/L-HPC (High-pressure Internal Cooling)

Order No.

Dimensions (mm)

MatchedInsert

Shim

Shim Screw

ClampPlate

Clamp PlateScrew

Spring

Wrench

ThreadPlug

InStock

OHX

CCO

DCLNR/ SI60M040080- CAD01R/20 20 115 38.52025CN**1204**DCN1204DDL2020X12-HPC 05612D LD

SJM050250D SPA7D TT15PD

STBG1/0.48D

○○

DCLNR/L2525X12-HPC

2525

130

38.525

CN**1204**

DCN1204DD

SI60M04008005612D

-CAD01R/LD

SJM050250D

SPA7D T

T15PD

STBG1/0.788D

○○

●StockOAvailable Upon Order

DDJNR/L-HPC (High-pressure Internal Cooling)

Order No.

Dimensions (mm)

MatchedInsert

Shim

Shim Screw

ClampPlate

ClampPlate Screw

Spring

Wrench

ThreadPlug

InStock

H B

OHX

CCO

Ceo

口

R L

DDJNR/ SI60M040080- CAD01R/20 20 125 45 2025DN**1506**DDN1504DD SJM050250D SPA7D TT15PDL2020X15-HPC 05612D LD

STBG1/0.48D

○○

DDJNR/L2525X15-HPC

25 25 140

45 25 32DN**1506**

DDN1504DD

SI60M040080-05612D

CAD01R/SJM050250DLD

SPA7D

TT15PD

STBG1/8D

0.78

○○

●StockOAvailable Upon Order

External Diameter Turning Tool Holder (Negative)

DVJNR/L-HPC (High-pressure Internal Cooling)

Order No.

Dimensions (mm)

MatchedInsert

Shim

Shim Screw

ClampPlate

Clamp PlateScrew

Spring

Wrench

ThreadPlug

InStock

OHX

口

R L

DVJNR/ SI60M040080- CAD02R/ STBG1/20 20125482025VN**1604**DVN1603DD SJM050250D SPA7D TT15PD 0.4○○L2020X16-HPC 05612D LD 8D

DVJNR/2525140L2525X16-HPC

48 25

32VN**1604**

DVN1603DD

SI60M040080-05612D

CAD02R/LD

SJM050250D

SPA7D

TT15PD

STBG1/0.78○8D

StockOAvailable Upon Order

DWLNR/L-HPC (High-pressure Internal Cooling)

Order No.

Dimensions (mm)

MatchedInsert

Shim

Shim Screw

ClampPlate

Clamp PlateScrew

Spring

Wrench

ThreadPlug

InStock

OHX

CMMCO

ccc

PDWLNR/ SI60M040080- CAD-20 20 120 40 2025WN**0804**DWN0804DDL2020X08-HPC 05612D 03RD

STB-SJM050250D SPA7D TT15PDG1/8D

0.4

○○

PDWLNR/2525 135 40 25 32L2525X08-HPC

WN**0804**

DWN0804DD

SI60M040080-05612D

CAD-03RD

SJM050250D

SPA7D T

T15PD

STB-G1/8D

0.7

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Positive)

SCLCR/L

Order No.	Dimensions (mm)						Matched	Screw	Wrench	Weight	In Stock
Order No.	H	B	LF	OHX	HF	WF	Insert	1	A	(KG)	R	L
SCLCR/L1010F06	10	10	80	12	10	12 CC0602		SI60M025060-03510H	TT08PH	0.06		●
SCLCR/L1212H09	12	12	100	20	12	16	CC09T3	SI60M040100-05812H	TT15PH	0.11		O
SCLCR/L1616H09	16	16	100	20	16	20	CC09T3	SI60M040100-05812H	TT15PH	0.2
SCLCR/L2020K09	20	20	125	20	20	25	CC09T3	SI60M040100-05812H	TT15PH	0.4
SCLCR/L2525M12	25	25	150	20	25	32	CC1204 SI60M050120-07012H		TT20PH	0.78

●StockOAvailable Upon Order

SDJCR/L

Order No.	Dimensions (mm)							Screw	Wrench	Weight	In Stock
Order No.	H	B	LF	OHX	HF	WF		CCO	口	(KG)	R	L
SDJCR/L1010F07	10	10	80	15	10	12	DC0702	SI60M025060-03510H	TT08PH	0.06	●	●
SDJCR1212H07	12	12	100	15	12	16	DC0702	SI60M025060-03510H	TT08PH	0.11
SDJCR/L1616H11	16	16	100	20	16	20	DC11T3	SI60M040100-05812H	TT15PH	0.2
SDJCR/L2020K11	20	20	125	22	20	25	DC11T3	SI60M040100-05812H	TT15PH	0.4
SDJCR/L2525M11	25	25	150	25	25	32	DC11T3	SI60M040100-05812H	TT15PH 0.78

StockOAvailable Upon Order

External Diameter Turning Tool Holder (Positive)

SSDCN

Order No.	Dimensions (mm)						Matched Insert	Screw	Wrench	Weight(KG)	In Stock
Order No.	H	B	LF	OHX	HF	WF	Matched Insert	小	口	Weight(KG)	In Stock
SSDCN1212H09	12	12	80	一	12	6	SC09T3	SI60M040100-05812H	TT15PH	0.1
SSDCN1616H09	16	16	100	一	16	8	SC09T3	SI60M040100-05812H	TT15PH	0.19
SSDCN2020K09	20	20	125		20	10	SC09T3	SI60M040100-05812H	TT15PH	0.39	O
SSDCN2525M12	25	25	150	一	25	12.5	SC1204	SI60M050120-07012H	TT20PH	0.77

●StockOAvailable Upon Order

STGCR/L

Order No.	Dimensions (mm)						Matched	Screw	Wrench	Weight	In Stock
Order No.	H	B	LF	OHX	HF	WF	Insert	O	口	(KG)	R	L
STGCR1010F09	10	10	80	12	10	12	TC0902	SI60M022060-03008H	TT06PH	0.06	●
STGCR/L1212H11	12	12	100	16	12	16	TC1102	SI60M025060-03510H	TT08PH	0.11		O
STGCR/L1616H11	16	16	100	20	16	20	TC1102	SI60M025060-03510H	TT08PH	0.2	●
STGCR/L2020K16	20	20	125	25	20	25	TC16T3	SI60M040100-05812H	TT15PH	0.4
STGCR/L2525M16	25	25	150	25	25	32	TC16T3	SI60M040100-05812H	TT15PH 0.78

Stock OAvailable Upon Order

External Diameter Turning Tool Holder (Positive)

Order No.	Dimensions (mm)						Matched Insert	Screw	Wrench 4		Weight (KG)	In Stock L
Order No.	H	B	LF	OHX	HF WF	CMTO	Matched Insert	Screw	Wrench 4		Weight (KG)		R
SVJCR1212H11	12	12	100	25	12	16	VC1103	SI60M025060-03510H		TT08PH	0.1
SVJCR/L1616H11	16	16	100	25	16	20		VC1103	SI60M025060-03510H	TT08PH	0.19
SVJCR/L2020K16	20	20	125	35	20	25		VC1604	SI60M040100-05812H	TT15PH	0.39
SVJCR/L2525M16	25	25	150	35	25	32		VC1604	SI60M040100-05812H	TT15PH	0.77

StockOAvailable Upon Order

External Diameter Turning Tool Holder (Positive)

SWLCR/L

Order No.	Dimensions (mm)						Matched	Screw	Wrench	Weight	In Stock
Order No.	H	B	LF	OHX	HF	WF	Insert	O	日	(KG)	R	L
SWLCR/L1212H06	12	12	100	15	12	16	WC06T3	SI60M040100-05812H	TT15PH	0.11
SWLCR/L1616H06	16	16	100	15	16	20	WC06T3	SI60M040100-05812H	TT15PH	0.2	●	●
SWLCR/L2020K06	20	20	125	15	20	25	WC06T3	SI60M040100-05812H	TT15PH	0.4
SWLCR/L2525M06	25	25	150	20	25	32	WC06T3	SI60M040100-05812H	TT15PH	0.78	•	•

StockOAvailable Upon Order

Type Representation Rules for Internal Hole Turning Tool Holders

①

③

④

⑤

① Tool Holder Material
A	Steel Tool Holder withCooling Hole
C	Cemented Carbide Tool Holder
E	Cemented Carbide Tool Holderwith Cooling Hole
S	Steel Tool Holder

② Shank Diameter

③ Shank Length

Code	Diameter
08	8
10	10
12	12
16	16
20	20
25	25
32	32

⑤ Insert Shape
C	80°Diamond
D	55°Diamond
R	Circular
S	Square
T	RegularTriangle
V	35°Diamond
W	Hexagon
X	SpecialShape

Code	Height
F	80
H	100
K	125
M	150
N	160
Q	180
R	200
S	250
T	300
U	350

④ Clamping Type
D	Double ClampingType
M	Module Locking TypeDouble ClampingType for HeavyCutting
P	Lever Locking Type
S	Screw ClampingType

0】

⑥ Tool Cutting Edge Angle

K
K
L
F
U
Q
W

B	$5 ^ { \circ }$
C	$7 ^ { \circ }$
D	$1 5 ^ { \circ }$
E	$2 0 ^ { \circ }$
$\mathsf { N }$	$0 ^ { \circ }$
$\mathsf { P }$	$1 1 ^ { \circ }$

⑧ Direction
R
L

⑨ Cutting Edge Length (mm)

Inscribed Circle
6.35	06	07	-	06	11	11	04
9.525	09	11	-	09	16	16	06
12.7	12	15	-	12	22	1	08
15.875	16	-	-	15	-	-	-
19.05	19	-	-	19	-	-	一
25.4	25	-	-	25	一	-	-
32	-	-	32	-	-	-	-

Internal Hole Turning Tool Holder

SCLCR/L

Order No.	Dimensions (mm)								Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°		O	F	(KG)	R	L
S08K-SCLCR/L06	10	8	5.5	125	15	7	13	CC0602	SI60M025050-03510H	TT08PH	0.05	●	●
S10K-SCLCR/L06	12	10	6.5	125	15	9	12	CC0602	SI60M025050-03510H	TT08PH	0.08
S12M-SCLCR/L06	16	12	7.5	150	20	11	10	CC0602	SI60M025060-03510H	TT08PH	0.14
S12M-SCLCR/L09	16	12	8	150	18	11	12	CC09T3	SI60M040080-05812H	TT15PH	0.14
S16Q-SCLCR/L09	20	16	10	180	24	15	10	CC09T3	SI60M040080-05812H	TT15PH	0.29
S20R-SCLCR/L09	25	20	12	200	30	18	8	CC09T3	SI60M040080-05812H	TT15PH	0.5		•
S25S-SCLCR/L09	32	25	16	250	38	23	6	CC09T3	SI60M040100-05812H	TT15PH	0.98
S25S-SCLCR/L12	32	25	16	250	38	23	8	CC1204	SI60M050120-07012H	TT20PH	0.98		●

Stock OAvailable Upon Order

SCLCR/L (Internal Cooling)

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°		CCTO	口	(KG)	R	L
A08K-SCLCR/L06	10	8	4.5	125	14	7	13	CCT0602*	SI60M025050-03510D	TT08PD	0.05	●	●
A10K-SCLCR/L06	12	10	6	125	17	9	12	CCT0602*	SI60M025050-03510D	TT08PD	0.08
A12M-SCLCR/L06	16	12	7	150	17	11	10	CCT0602*	SI60M025050-03510D	TT08PD	0.14	●	●
A16Q-SCLCR/L09	20	16	9	180	27	15	10	CCT09T3*	SI60M040080-05710D	TT15PD	0.29
A20Q-SCLCR/L09	25	20	11	180	28	18	8	CCT09T3*	SI60M040080-05710D	TT15PD	0.5		●
A25R-SCLCR/L09	32	25	14	200	35	23	6	CCT09T3*	SI60M040080-05710D	TT15PD	0.98	●	●
E08K-SCLCR/L06	10	8	5	125	8	7.5	13	CCT0602*	SI60M025050-03510D	TT08PD	0.08	O	O
E10M-SCLCR/L06	12	10	6	150	14	9.5	12	CCT0602*	SI60M025050-03510D	TT08PD	0.16	O	O
E12Q-SCLCR/L06	14	12	7	180	14	11	10	CCT0602*	SI60M025050-03510D	TT08PD	0.28	O	O
E16R-SCLCR/L09	18	16	9	200	20	15	10	CCT09T3*	SI60M040080-05710D	TT15PD	0.56	O	O
E20S-SCLCR/L09	22	20	11	250	26	19	8	CCT09T3*	SI60M040080-05710D	TT15PD	1.1	O	O
E25T-SCLCR/L09	28	25	14	300	29	23	6	CCT09T3*	SI60M040080-05710D	TT15PD	2.06	O	O

●Stock OAvailable Upon Order

SCLCR/L-A16

Internal Hole Turning Tool Holder

Order No.	Dimensions (mm)							Matched	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Insert	CO	A	(KG)	R	L
S07M-SCLCR/L06-A16	9	16	4.25	150	18	15	15	CC0602	SI60M025050-03510H	TT08PH	0.22		O
S08M-SCLCR/L06-A16	10	16	5	150	25	15	13	CC0602	SI60M025050-03510H	TT08PH	0.22		O
S10M-SCLCR/L06-A16	13	16	6	150	26	15	12	CC0602	SI60M025050-03510H	TT08PH	0.22
S12M-SCLCR/L06-A16	15	16	7	150	28	15	10	CC0602	SI60M025060-03510H	TT08PH	0.22		O

StockOAvailable Upon Order

SCKCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert		4	(KG)	R	L
S08K-SCKCR/L06	10	8	5.5	125	12	7	13	CC0602	SI60M025050-03510H	TT08PH	0.05	●	O
S10K-SCKCR/L06	12	10	6.5	125	20	9	12	CC0602	SI60M025050-03510H	TT08PH	0.08	●	O
S12M-SCKCR/L06	16	12	8	150	22	11	10	CC0602	SI60M025060-03510H	TT08PH	0.14	O	O
S12M-SCKCR/L09	16	12	8	150	23	11	12	CC09T3	SI60M040080-05812H	TT15PH	0.14		O
S16Q-SCKCR/L09	20	16	10	180	28	15	10	CC09T3	SI60M040080-05812H	TT15PH	0.29		O
S20R-SCKCR/L09	25	20	12	200	29	18	8	CC09T3	SI60M040080-05812H	TT15PH	0.5	O	O
S25S-SCKCR/L09	32	25	16	250	37	23	6	CC09T3	SI60M040100-05812H	TT15PH	0.98		O

StockOAvailable Upon Order

SDUCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert		F	(KG)	R	L
S10K-SDUCR/L07	12	10	7	125	15	9	10	DC0702	SI60M025050-03510H	TT08PH	0.08	●	●
S12M-SDUCR/L07	16	12	9	150	22	11	8	DC0702	SI60M025060-03510H	TT08PH	0.14
S16Q-SDUCR/L07	20	16	11	180	27	15	6	DC0702	SI60M025060-03510H	TT08PH	0.29
S16Q-SDUCR/L11	20	16	11	180	28	15	6	DC11T3	SI60M040080-05812H	TT15PH	0.29
S20R-SDUCR/L11	25	20	13	200	30	18	6	DC11T3	SI60M040080-05812H	TT15PH	0.5
S25S-SDUCR/L11	32	25	16	250	38	23	4	DC11T3	SI60M040100-05812H	TT15PH	0.98	●	●

Stock OAvailable Upon Order

SDUCR/L (Internal Cooling)

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°		小	A	(KG)	R	L
A10K-SDUCR/L07	13	10	7.7	125	15	9	10	DCT0702*	SI60M025050-03510D	TT08PD	0.08
A12M-SDUCR/L07	16	12	8.5	150	22	11	8	DCT0702*	SI60M025050-03510D	TT08PD	0.14	●
A16Q-SDUCR/L07	20	16	11	180	27	15	6	DCT0702*	SI60M025050-03510D	TT08PD	0.29
A20Q-SDUCR/L11	25	20	14.5	180	30	18	6	DCT11T3*	SI60M040080-05710D	TT15PD	0.5
A25R-SDUCR/L11	32	25	18.5	200	35	23	6	DCT11T3*	SI60M040080-05710D	TT15PD	0.98
E10M-SDUCR/L07	13	10	7	150	14	9.5	10	DCT0702*	SI60M025050-03510D	TT08PD	0.16	O	O
E12Q-SDUCR/L07	16	12	9	180	14	11	8	DCT0702*	SI60M025050-03510D	TT08PD	0.28	O	O
E16R-SDUCR/L07	20	16	11	200	20	15	6	DCT0702*	SI60M025050-03510D	TT08PD	0.56	O	O

Stock OAvailable Upon Order

Internal Hole Turning Tool Holder

SDQCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN	1	WFDCON	LF	OHN	H	$\mathtt { a } ^ { \circ }$	Matched Insert	U	A	(KG)	R	L
S10K-SDQCR/L07	12	10	7	125	20	9	10	DC0702	SI60M025050-03510H	TT08PH	0.08	●	O
S12M-SDQCR/L07	16	12	9	150	20	11	8	DC0702	SI60M025060-03510H	TT08PH	0.14	●	O
S16Q-SDQCR/L07	20	16	11	180	25	15	6	DC0702	SI60M025060-03510H	TT08PH	0.29	●	O
S16Q-SDQCR/L11	20	16	11	180	24	15	6	DC11T3	SI60M040080-05812H	TT15PH	0.29	●	●
S20R-SDQCR/L11	25	20	13	200	32	19	6	DC11T3	SI60M040080-05812H	TT15PH	0.5	●	O
S25S-SDQCR/L11	32	25	16	250	33	23	4	DC11T3	SI60M040100-05812H	TT15PH	0.98	●	●

●StockOAvailable Upon Order

SDQCR/L (Internal Cooling)

Order No.	Dimensions (mm)								Screw	Wrench	Weight	In Stock
Order No.	DMIN	1	WFDCON	LF	OHN	H	$\mathtt { a } ^ { \circ }$		CCTO	4	(KG)	R	L
A10K-SDQCR/L07	13	10	7	125	20	9	10	DCT0702*	SI60M025050-03510D	TT08PD	0.08	●	O
A12M-SDQCR/L07	16	12	9	150	22	11	8	DCT0702*	SI60M025050-03510D	TT08PD	0.14	●	O
A16Q-SDQCR/L07	20	16	11	180	27	15	6	DCT0702*	SI60M025050-03510D	TT08PD	0.29	●	O
A20Q-SDQCR/L11	25	20	13	180	35	18	6	DCT11T3*	SI60M040080-05710D	TT15PD	0.5	●	O
A25R-SDQCR/L11	32	25	17	200	38	23 4		DCT11T3* SI60M040080-05710D		TT15PD 0.98

●StockOAvailable Upon Order

SDXCR/L

●StockOAvailable Upon Order

Order No.	Dimensions (mm)								Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°		CCO	P	(KG)	R	L
S08K-SDXCR/L07	10	8	5.5	125	18	7	12	DC0702	SI60M025050-03510H	TT08PH	0.05	●	O
S10K-SDXCR/L07	12	10	6.5	125	18	9	10	DC0702	SI60M025050-03510H	TT08PH	0.08	●	O
S12M-SDXCR/L07	16	12	8	150	22	11	8	DC0702	SI60M025060-03510H	TT08PH	0.14		O
S16Q-SDXCR/L07	20	16	10	180	32	15	6	DC0702	SI60M040100-05812H	TT08PH	0.29		O
S20R-SDXCR/L11	25	20	12	200	38	18	6	DC11T3	SI60M040080-05812H	TT15PH	0.5
S25S-SDXCR/L11	32	25	14	250	45	23	4	DC11T3	SI60M040100-05812H	TT15PH	0.98	●	O

SSKCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°			A	(KG)	R	L
S12M-SSKCR/L09	16	12	9	150	22	11	10	SC09T3	SI60M040080-05812H TT15PH		0.14	O	O
S16Q-SSKCR/L09	20	16	11	180	29	15	10	SC09T3	SI60M040080-05812H	TT15PH	0.29		O
S20R-SSKCR/L09	25	20	13	200	29	18	8	SC09T3	SI60M040080-05812H	TT15PH	0.5	●	O
S25S-SSKCR/L12	32	25	17	250	38	23	6	SC1204	SI60M050120-07012H	TT20PH	0.98	O	O

StockOAvailable Upon Order

Internal Hole Turning Tool Holder

STUCR/L

Order No.	Dimensions (mm)								Screw	Wrench	Weight	In Stock
Order No.	DMIN	1	DCONWF	LF	OHN	H	α°		CO	口	(KG)	R	L
S08K-STUCR/L09	10	8	5.5	125	15	7	15	TC0902	SI60M022040-03008H	TT06PH	0.05		O
S10K-STUCR/L09	12	10	6.5	125	15	9	13	TC0902	SI60M022040-03008H	TT06PH	0.08	●	O
S10K-STUCR/L11	12	10	6.5	125	15	9	12	TC1102	SI60M025050-03510H	TT08PH	0.08	●	O
S12M-STUCR/L11	16	12	8	150	21	11	10	TC1102	SI60M025060-03510H	TT08PH	0.14		O
S16Q-STUCR/L11	20	16	10	180	27	15	8	TC1102	SI60M025060-03510H	TT08PH	0.29		O
S20R-STUCR/L11	25	20	12	200	27	18	6	TC1102	SI60M025060-03510H	TT08PH	0.5	●
S20R-STUCR/L16	25	20	12	200	27	18	4	TC16T3	SI60M040080-05812H	TT15PH	0.5		O
S25S-STUCR/L16	32	25	16	250	38	23	6	TC16T3	SI60M040100-05812H	TT15PH	0.98	●

StockOAvailable Upon Order

STWCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert	小	A	(KG)	R	L
S08K-STWCR/L09	10	8	6	125	16	7	15	TC0902	SI60M022040-03008H	TT06PH	0.05	●	O
S10K-STWCR/L11	12	10	8	125	20	9	10	TC1102	SI60M025050-03510H	TT08PH	0.08		O
S12M-STWCR/L11	16	12	9	150	20	11	8	TC1102	SI60M025060-03510H	TT08PH	0.14		O
S16Q-STWCR/L11	20	16	11	180	27	15	6	TC1102	SI60M025060-03510H	TT08PH	0.29	O	O
S20R-STWCR11	25	20	13	200	30	18	4	TC1102	SI60M025060-03510H	TT08PH	0.5	O
S20R-STWCR/L16	25	20	15	200	32	18	8	TC16T3	SI60M040080-05812H	TT15PH	0.5	O	O
S25S-STWCR/L16	32	25	17	250	44	23	6	TC16T3	SI60M040100-05812H	TT15PH	0.98		O

●StockOAvailable Upon Order

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert	1	A	(KG)	R	L
S08K-STFCR/L09	10	8	5.5	125	15	7	15	TC0902	SI60M022040-03008H	TT06PH	0.05		O
S10K-STFCR/L09	12	10	6.5	125	15	9	10	TC0902	SI60M022040-03008H	TT06PH	0.08	●	●
S12M-STFCR/L09	16	12	8	150	20	11	8	TC0902	SI60M022060-03008H	TT06PH	0.14		O
S12M-STFCR/L11	16	12	8	150	25	11	6	TC1102	SI60M025060-03510H	TT08PH	0.14
S16Q-STFCR/L11	20	16	10	180	27	15	4	TC1102	SI60M025060-03510H	TT08PH	0.29		•
S20R-STFCR/L11	25	20	12	200	27	18	8	TC1102	SI60M025060-03510H	TT08PH	0.5	●	•
S20R-STFCR/L16	25	20	12	200	27	18	6	TC16T3	SI60M040080-05812H	TT15PH	0.5		O
S25S-STFCR/L16	32	25	16	250	40	23		TC16T3	SI60M040100-05812H	TT15PH	0.98	●	●

StockOAvailable Upon Order

STFCR/L (Internal Cooling)

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert		F	(KG)	R	L
A10K-STFCR/L09	12	10	6.8	125	10	9	13	TCT0902*	SI60M022060-03008D	TT06PD	0.08
A12M-STFCR/L09	16	12	8	150	10	11	10	TCT0902*	SI60M022060-03008D	TT06PD	0.14	●	O
S12M-STFCR/L1102	14	12	6.5	150	25	11	10	TCT1102*	SI60M022050-03008D	TT08PD	0.14	●	●
A16Q-STFCR/L1102	18	16	9	180	25	15	8	TC1102	SI60M022050-03008D	TT08PD	0.29	●	●
A20Q-STFCR/L1102	25	20	11	180	25	18	6	TC1102	SI60M022050-03008D	TT08PD	0.5
A25R-STFCR/L16	32	25	17	200	40	23	6	TCT16T3*	SI60M040080-05710D	TT15PD	0.98		●

●StockOAvailable Upon Order

Internal Hole Turning Tool Holder

SVUCR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	$\mathtt { a } ^ { \circ }$		COCO	A	(KG)	R	L
S16Q-SVUCR/L11	20	16	12	180	25	15 10		VC1103	SI60M025060-03510H	TT08PH	0.29		O
S20R-SVUCR/L11	25	20	16	200	26	18	8	VC1103	SI60M025060-03510H	TT08PH	0.5
S25S-SVUCR/L16	33	25	20	250	36	23	8	VC1604	SI60M040100-05812H	TT15PH	0.98

●Stock OAvailable Upon Order

SVUCR/L (Internal Cooling)

Order No.

Dimensions (mm)

Matched Insert

Screw

Wrench

Weight

In Stock

DMIN1

DCON

OHN

$\mathtt { a } ^ { \circ }$

(KG)

A16Q-SVUCR/L11

16 13.5180

15 10

VC*T1103** SI60M025050-03510D

TT08PD

0.29

A20Q-SVUCR/L16

180

VC*T1604**

SI60M040080-05710D

TT15PD

0.5

●

A25R-SVUCR/L16

200

VC*T1604**

SI60M040080-05710D

TT15PD

0.98

●StockOAvailable Upon Order

SWLCR/L

●Stock OAvailable Upon Order

Order No.	Dimensions (mm)							Matched	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Insert	小	A	(KG)	R	L
S12M-SWLCR/L06	16	12	8	150	20	11	12	WC06T3 SI60M040080-05812H TT15PH			0.14	··
S16Q-SWLCR/L06	20	16	10	180	25	14.8	10	WC06T3	SI60M040080-05812H	TT15PH	0.29	●
S20R-SWLCR/L06	25	20	12	200	28	18.4	8	WC06T3	SI60M040080-05812H	TT15PH	0.5		•
S25S-SWLCR/L06	32	25	16	250	40	23.4	6	WC06T3	SI60M040100-05812H	TT15PH	0.98	●	●

SCLPR/L

Order No.	Dimensions (mm)								Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°		i	F	(KG)	R	L
S08K-SCLPR/L06	10	8	5.5	125	15	7	13	CP0602	SI60M025050-03510H	TT08PH	0.05	●
S10K-SCLPR/L06	12	10	6.5	125	15	9	12	CP0602	SI60M025050-03510H	TT08PH	0.08
S12M-SCLPR/L06	16	12	8	150	20	11	10	CP0602	SI60M025050-03510H	TT08PH	0.14
S12M-SCLPR/L09	16	12	8	150	26	11	12	CP09T3	SI60M040080-05812H	TT15PH	0.14	●
S16Q-SCLPR/L09	20	16	10	180	27	15	10	CP09T3	SI60M040080-05812H	TT15PH	0.29	●	•
S20R-SCLPR/L09	25	20	12	200	29	18	8	CP09T3	SI60M040080-05812H	TT15PH	0.5		O
S25S-SCLPR/L09	32	25	16
				250	38	23
				250	38	23	6	CP09T3	SI60M040100-05812H	TT15PH	0.98	●	●

●Stock OAvailable Upon Order

Internal Hole Turning Tool Holder

STFPR/L

Order No.	Dimensions (mm)							Matched Insert	Screw	Wrench	Weight	In Stock
Order No.	DMIN1	DCON	WF	LF	OHN	H	α°	Matched Insert	CCO	P	(KG)	R
S10K-STFPR1102	12	10	6.5	125	16	9	12	TP1102	SI60M025050-03510H	TT08PH	0.08
S12M-STFPR1102	16	12	8	150	25	11	10	TP1102	SI60M025050-03510H	TT08PH	0.14
S16Q-STFPR1102	20	16	10	180	27	15	8	TP1102	SI60M025060-03510H	TT08PH	0.29
S20R-STFPR1102	25	20	12	200	30	18	6	TP1102	SI60M025060-03510H	TT08PH	0.5	O
S20R-STFPR16T3	25	20	12	200	30	18	4	TP16T3	SI60M040080-05812H	TT15PH	0.5	•
S25S-STFPR16T3	32	25	16	250	40	23	6	TP16T3	SI60M040100-05812H	TT15PH	0.98	O

StockOAvailable Upon Order

PARTING OFF AND GROOVING TOOLS

Type Representation Rules for Parting Off and Grooving Inserts GT Series Insert

300

020

06 -MC

③

④

① Series Name

② Teeth

S=Single Edged

D=Double Edged

⑤ Tip Arc Radius

020=0.20mm

⑥ Insert Direction

R=Right-handed

L=Left-hand

The First Letter	The Second Letter
F=Low Feed	C=Parting Off
M=Medium Feed	T=Turning
R=High Feed	G=Grooving
O=Specific Optimized	R=Profile Machining

=Middle

⑧ Geometry

⑤]

③ Cutting Width

Cutting Width<10mm The First Digit is Omitted, 300=3.0mm

Cutting Width≥10mm Not Omitted, 1000=10.0mm

⑦ Lead Angle

06=6°

15=15°

□=0°

④ Tool Apron Code

Insert	Matching ToolHolder
B	B
C	C
D	D (Preferred), C
E	E (Preferred), D, C
F	F
G	G (Preferred), F
H	H (Preferred), G, F
J	J

Type Representation Rules for Parting Off and Grooving Inserts GK Series Insert

15 - MT

③

【④】

⑤

【⑦】

① Series Name

② Teeth

③ Cutting Width

④ Tip Arc Radius

S=Single Edged

30=3.0mm

02=0.2mm

D=Double Edged

40=4.0mm

04=0.4mm

20=2.0mm

⑤ Insert Direction

⑥ Lead Angle

⑦ Geometry

R=Right-handed

15=15°

The First Letter

The Second Letter

L=Left-hand

□=0°

F=Low Feed

C=Parting Off

□=Middle

M=Medium Feed

T=Turning

R=High Feed

G=Grooving

O=Specific Optimized

R=Profile Machining

Type Representation Rules for Parting Off and Grooving Inserts GB Series Insert

100

R - 050

①】

②

③

④】

⑤

① Series Name

② Insert Type

③ Insert Size

R=Round Nose

IC=9.525mm

=Square Nose

IC=12.7mm

④ Cutting Width

⑤ Insert Direction

⑥ Tip Arc Radius

100=1.00mm

R=Right-handed

050=0.5mm

L=Left-hand

Type Representation Rules for Parting Off and Grooving Inserts GN Series Insert

M150

【④】

[⑦】

① Series Name

② Machining Type

③ Additional Information

G=Grooving

④ Additional Information

D=Deep Grooving

R=Profile

P=Positive Rake Angle

=No Rake Angle

⑤ Insert Thickness

2=3.81mm

⑥ Cutting Width

⑦ Insert Direction

Metric System: M150=1.5mm

3=4.95mm

R=Right-handed

Imperial System: 125=0.125inch

L=Left-hand

Type Representation Rules for Parting Off and Grooving Inserts GST Series Insert

GSTS

150

16 - U

【④】

[⑤]

① Series Name

② Insert Size

③ Insert Thickness

④ Insert Direction

GSTC

Unique to the GSTS Series

2=2.2mm

GSTS (Thin)

R=Right-handed

Insert Height=8.7mm

3=3.0mm

L=Left-hand

Insert Height=9.5mm

4=4.0mm

⑤ Cutting Tool Width

⑥ Lead Angle Direction

⑦ Lead Angle

150=1.5mm

R=Right-biased

16=16°

L=Left-biased

20=20°

⑧ Geometry

N=No Bias

Code	Specifications	GAN
U	GSTC3*N-U	15°
	GSTSA*-U	15°
	GSTC4*-U	20°
	GSTSB*-U	20°
	GSTC3*R16-U	24°
T	GSTC*-T	12°
N	GSTC*-N	0°
N	GSTC*R20-N	0°

Type Representation Rules for Parting Off and Grooving Tool Holders GT Series Tool Holder

GT E P R 2525 M 45-H 25 D65-S

①】

① Series Name

② Machining Type

I=Internal Hole Making

E=External Machining

F=End Face Machining

①]

③ Shape Of Tool Holder

U=Grinding Undercut

P=Vertical Type

□=Linear

④ Tool Direction

R=Right-handed

L=Left-hand

N=Middle

⑤ Shank Size

External Diameter Tool Holder: Height\*Width

Tool Holder with Internal Hole: Minimum Machining Diameter\*Shank Diameter

⑨ Maximum Cutting Depth

Conven- tional Tool	25: CDX=25mm
Dedicated Tool for Automatic	D16:CUTDIA =16mm

⑩ Minimum Diameter of the First Cut

Unique to End Face Machining

D65:DAXIN=65mm

⑥ Length of Tool Holder

Code	Length
F	85 mm
H	100 mm
J	110 mm
JX	120 mm
K	125 mm
M	150 mm
Q	180 mm
R	200 mm
S	250 mm
T	300 mm
U	350 mm

⑦ Shank Angle

Unique to the U-shaped Tool Holder

45=45°

75=75°

⑩ Additional Information

S=With Curve Reinforcement

C=With High-Pressure Cooling

SC=With Curve Reinforcement and High-Pressure Cooling

□=Without Curve Reinforcement

⑧ Tool Apron Code

ToolHolder	Matched Insert
B	B
C	C (Preferred), D, E
D	D (Preferred), E
E	E
F	F (Preferred), G, H
G	G (Preferred), H
H	H
J	J

Type Representation Rules for Parting Off and Grooving Tool Holders GK Series Tool Holder

GK F P R 2525-4 T25 D65-S

① Series Name

② Machining Type

E=External Machining

I=Internal Hole Making

F=End Face Machining

③ Shape Of Tool Holder

U=Grinding Undercut

P=Vertical Type

④ Tool Direction

R=Right-handed

□=Linear

L=Left-hand

N=Middle

⑤ Shank Size

External Diameter Tool Holder: Height\*Width

Tool Holder with Internal Hole: Minimum Machining Diameter\*Shank

⑥ Insert Cutting Width

4=4.0mm

=Without Curve Reinforcement

⑧ Minimum Diameter of the First Cut

T25: CDX=25mm

Diameter

Unique to End Face Machining

⑦ Maximum Cutting Depth

⑨ Additional Information

D65:DAXIN=65mm

S=With Curve Reinforcement

PCD Turning Insert (Positive)

Recommended Cutting Data PCBN Cutting Tools

Recommended Cutting Data PCD Cutting Tools

PCBN Chip Breaker Insert

List of Turning Tool Holders

① Clamping Mechanism

④ Insert Relief Angle

② Insert Shape

⑤ Cutting Direction

MCBNR/L

MCLNR/L

MDJNR/L

MDPNN

MSBNR/L

MSKNR/L

MSSNR/L

MTENN

MTFNR/L

MTGNR/L

MTJNR/L

MVQNR/L

MWLNR/L

PCBNR/L

PCLNR/L

PDJNR/L

PSBNR/L

PSSNR/L

PRDCN

PTGNR/L

PWLNR/L

DCLNR/L-HPC (High-pressure Internal Cooling)

DDJNR/L-HPC (High-pressure Internal Cooling)

External Diameter Turning Tool Holder (Negative)

DVJNR/L-HPC (High-pressure Internal Cooling)

DWLNR/L-HPC (High-pressure Internal Cooling)

SCLCR/L

SDJCR/L

SSDCN

STGCR/L

SWLCR/L

SDUCR/L

SDQCR/L

SSKCR/L

SVUCR/L

SVUCR/L (Internal Cooling)

SWLCR/L

SCLPR/L

PARTING OFF AND GROOVING TOOLS

⑧ Geometry

③ Cutting Width

④ Tool Apron Code

⑦ Geometry

GT E P R 2525 M 45-H 25 D65-S

⑤ Shank Size

⑨ Maximum Cutting Depth

⑥ Length of Tool Holder

⑦ Shank Angle

⑧ Tool Apron Code

GK F P R 2525-4 T25 D65-S

⑤ Shank Size

快速跳转到指定页