该页无缩略图
Parting Off and Grooving Tool Holders-GB Series
External Diameter Tool Holder
The diagram shows the right hand
| Order No. | Dimensions (mm) | Matched Insert | Screw | Wrench | Weight(KG) | In Stock | ||||||
| H=HF | B | CDX | LF | WF | A |  |  | R | L | |||
| GBER/L2020K3 | 20 | 20 | 2.5 | 125 | 25 | GB3... | SI60M035120-05316H TT15PH | 0.39 | ● | |||
| GBER/L2525M3 | 25 | 25 | 2.5 | 150 | 30 | GB3... | SI60M035120-05316H | TT15PH | 0.74 | ● | ||
| GBER/L2020K415 | 20 | 20 | 4.0 | 125 | 25 | 1.0 | GB4...(1.0≤W<2.5) | SI60M050120-07217H | TT20PH | 0.39 | ● | ● |
| GBER/L2525M415 | 25 | 25 | 4.0 | 150 | 30 | 1.0 | GB4...(1.0≤W<2.5) | SI60M050120-07217H | TT20PH | 0.74 | ● | ● |
| GBER/L2020K425 | 20 | 20 | 20 4.5 | 125 | 25 | 2.0 | GB4...(2.5≤W<3.3) | SI60M050120-07217H | TT20PH | 0.39 | ● | O |
| GBER/L2525M425 | 25 | 25 | 4.5 | 150 | 30 | 2.0 | GB4...(2.5≤W<3.3) | SI60M050120-07217H | TT20PH | 0.74 | ● | O |
| GBER/L2020K435 | 20 20 | 5.5 | 125 | 25 | 3.0 | GB4...(3.3≤W<4.3) | SI60M050120-07217H | TT20PH | 0.39 | O | O | |
| GBER/L2525M435 | 25 25 | 5.5 | 150 | 30 | 3.0 | GB4...(3.3≤W<4.3) | SI60M050120-07217 H | TT20PH | 0.74 | ● | O | |
Notes: SI60M 035120\* representative M3.5X12
Stock OAvailable Upon Order
Stock OAvailable Upon Order
Parting Off and Grooving Tool Holders-GB Series
Tool Holder with Internal Hole
| Order No. | Dimensions (mm) | Matched | Screw | Wrench | Weight | In Stock | ||||||
| DMIN | DCONMS | CDX | WF | LF | H | Insert | M0 | (KG) | R | L | ||
| GBIR/L2620Q3 26 | 20 | 3 | 13 180 18 GB3... | SI60M035120-05316H TT15PH 0.44 | ||||||||
| GBIR/L3525R4 | 35 | 25 | 4.5 | 17.5 | 200 | 23 | GB4... | SI60M050120-07217H | TT20PH | 0.77 | ● | ● |
Notes: SI60M035120\* representative M3.5X12 The right-handed (R) insert is applicable to the left-hand (L) tool holder, and the left-handed (L) insert is applicable to the right-handed (R) tool holder.
●Stock OAvailable Upon Order
●Stock OAvailable Upon Order
Parting Off and Grooving Tool Holders-GN Series
External Diameter Tool Holder-linear
The diagram shows the right hand
| Order No. | Dimensions (mm) | Matched | Screw | Clamp Plate | Wrench | Weight(KG) | InStock | |||||
| H=HF | B | CDX | LF | WF | LH | Insert |  |  |  | |||
| GNSR1616H2 | 16 16 | 3.5 100 | 20 | 19 | SCAM040120H | CAN02RH | TH30LH | 0.20 | ● | |||
| GNSR2020K2 | 20 | 20 | 3.5 | 125 | 25 | 19 | GN.2R | SCAM040120H | CAN02RH | TH30LH | 0.38 | O |
| GNSR2525M2 | 25 | 25 | 25 3.5 | 150 | 32 | 19 | SCAM040120H | CAN02RH | TH30LH | 0.74 | O | |
| GNSL1616H2 | 16 | 16 | 3.5 | 100 | 20 | 19 | SCAM040120H | CAN02LH | TH30LH | 0.20 | O | |
| GNSL2020K2 | 20 | 20 | 20 3.5 | 125 | 25 | 19 | GN.2L | SCAM040120H | CAN02LH | TH30LH | 0.38 | O |
| GNSL2525M2 | 25 | 25 | 3.5 | 150 | 32 | 19 | SCAM040120H | CAN02LH | TH30LH | 0.74 | O | |
| GNSR2020K3 | 20 | 20 | 20 5.3 | 125 | 25 | 32 | GN.3R | SCAM050200H | CAN03RH | TH40LH | 0.39 | ● |
| GNSR2525M3 | 25 | 25 | 5.3 | 150 | 32 | 32 | SCAM050200H | CAN03RH | TH40LH | 0.74 | ● | |
| GNSL2020K3 | 2020 | 5.3 | 125 | 25 | 32 | GN.3L | SCAM050200H | CAN03LH | TH40LH | 0.39 | O | |
| GNSL2525M3 | 25 | 25 | 5.3 | 150 | 32 | 32 | SCAM050200H | CAN03LH | TH40LH | 0.74 | ● | |
Notes: SCAM040120H representative M4X12 When used with GNGDP inserts, CDX shall be subject to that of the inserts.
Stock OAvailable Upon Order
Stock OAvailable Upon Order
①The right-handed (R) insert is applicable to the left-hand (L) tool holder, and the left-hand (L) insert is applicable to the right-handed (R) tool holder. ②When used with GNGDP inserts,CDX shall be subject to that of the inserts.
Parting Off and Grooving Tool Holders-GN Series
External Diameter Tool Holder-vertical
The diagram shows the right hand
| Order No. | Dimensions (mm) | Matched | Screw | Clamp Plate | Wrench | Weight(KG) | InStock | ||||
| H=HF | B | CDX | LF | WF | Insert |  |  |  | |||
| GNER2020K2 | 20 | 203 | .5 | 125 | 25 | SCAM040120H | CAN02LH | TH30LH | 0.38 | O | |
| GNER2525M2 | 25 | 25 | 3.5 | 150 | 32 | GN.2L | SCAM040120H | CAN02LH | TH30LH | 0.39 | O |
| GNEL2020K2 | 20 | 20 | 20 3.5 | 125 | 25 | GN.2R | SCAM040120H | CAN02RH | TH30LH | 0.38 | O |
| GNEL2525M2 | 25 | 25 | 3.5 | 150 | 32 | SCAM040120H | CAN02RH | TH30LH | 0.39 | O | |
| GNER2525M3 | 25 | 25 | 5.3 | 150 | 32 | GN.3L | SCAM050200H | CAN03LH | TH40LH | 0.39 | O |
| GNEL2525M3 | 25 | 25 | 5.3 | 150 | 32 | GN.3R | SCAM050200H | CAN03RH | TH40LH | 0.39 | O |
Notes: SCAM040120H representative M4X12
StockOAvailable Upon Order
StockOAvailable Upon Order
Parting Off and Grooving Tool Holders-GN Series
Tool Holder with Internal Hole
The diagram shows the right hand
| Order No. | Dimensions (mm) | Matched | Screw | ClampPlate | Wrench | Weight(KG) | InStock | ||||
| DMIN | DCONMS | WF | LF | CS | Insert |  |  |  | |||
| GNAR20Q2 | 26 | 20 | 13 | 180 | 1/8-27 NPT | GN.2L | SCAM040120H | CAN02LH | TH30LH | 0.44 | O |
| GNAR25R2 | 34 | 25 | 17 | 200 | 1/4-18 NPT | SCAM040120H | CAN02LH | TH30LH | 0.77 | O | |
| GNAL20Q2 | 26 | 20 | 13 | 180 | 1/8-27 NPT | GN.2R | SCAM040120H | CAN02RH | TH30LH | 0.44 | |
| GNAL25R2 | 34 | 25 | 17 | 200 | 1/4-18 NPT | SCAM040120H | CAN02RH | TH30LH | 0.77 | O | |
| GNAR25R3 | 34 | 25 | 17 | 200 | 1/4-18 NPT | GN.3L | SCAM050200H | CAN03LH | TH40LH | 0.77 | O |
| GNAL25R3 | 34 | 25 | 17 | 200 | 1/4-18 NPT | GN.3R | SCAM050200H | CAN03RH | TH40LH | 0.77 | O |
Notes: SCAM040120H representative M4X12
①The right-handed (R) insert is applicable to the left-hand (L) tool holder, and the left-hand (L) insert is applicable to the right-handed (R) tool holder. ②When used with GNGDP inserts, CDX shall be subject to that of the inserts.
Stock OAvailable Upon Order
①The right-handed (R) insert is applicable to the left-hand (L) tool holder, and the left-hand (L) insert is applicable to the right-handed (R) tool holder. ②When used with GNGDP inserts, CDX shall be subject to that of the inserts.
Stock OAvailable Upon Order
Parting Off and Grooving Tool Holders-GST Series
External Diameter Tool Holder Dedicated for Automatic Lathe
The diagram shows the right hand
| Order No. | Dimensions (mm) | MatchedInsert | Screw | Wrench | Weight | In Stock | ||||||
| H=HF | B | CDX | CUTDIA | LF | WF | M0 |  | (KG) | R | L | ||
| GSTR/L1010JK3 | 10 | 10 | 6 | 12 | 120 | 10 | SSAM045095Q | TT10PQ | 0.09 | ● | O | |
| GSTR/L1212JK3 | 12 | 12 | 6 | 12 | 120 | 12 | GSTC3R/L** | SSAM045095Q | TT10PQ | 0.14 | ● | ● |
| GSTR/L1616JK3 | 16 | 16 | 6 | 12 | 120 | 16 | SSAM045095Q | TT10PQ | 0.24 | ● | O | |
| GSTR/L2020JK3 | 20 | 20 | 6 | 12 | 120 | 20 | SSAM045095Q | TT10PQ | 0.40 | ● | O | |
| GSTR/L1010JK4 | 10 | 10 | 8 | 16 | 120 | 10 | SSAM045095Q | TT10PQ | 0.09 | ● | O | |
| GSTR/L1212JK4 | 12 | 12 | 8 | 16 | 120 | 12 | GSTC4R/L** | SSAM045095Q | TT10PQ | 0.14 | ● | ● |
| GSTR/L1616JK4 | 16 | 16 | 8 | 16 | 120 | 16 | SSAM045095Q | TT10PQ | 0.24 | O | ||
| GSTR/L2020JK4 | 20 | 20 | 8 | 16 | 120 | 20 | SSAM045095Q | TT10PQ | 0.40 | ● | O | |
Notes: SSAM045095Q representative M4.5X9.5
Stock OAvailable Upon Order
Stock OAvailable Upon Order
External Diameter Tool Holder Used for Sub-spindle of Automatic Lathe
Parting Off and Grooving Tool Holders-GST Series
| Order No. | Dimensions (mm) | MatchedInsert | Screw | Wrench | Weight(KG) | In Stock | ||||||
| H=HF | B | CDX | CUTDIA | LF | WF |  |  | R | L | |||
| GSTR/L1010JK3-RS | 10 | 10 | 6 | 12 | 120 | 7.2GSTC3R/L** | SSAM045070Q TT10PQ | 0.09 O | ||||
| GSTR/L1212JK3-RS | 12 | 12 | 6 | 12 | 120 | SSAM045070Q | TT10PQ | 0.14 | ● | O | ||
| GSTR/L1010JK4-RS | 10 | 10 | 8 | 16 | 120 | 7.2 | GSTC4R/L** | SSAM045070Q | TT10PQ | 0.09 | ● | O |
| GSTR/L1212JK4-RS | 12 | 12 | 8 | 16 | 120 | 7.2 | SSAM045070Q | TT10PQ | 0.14 | ● | ● | |
Notes: SSAM045070Q representative M4.5X7
●StockOAvailable Upon Order
●StockOAvailable Upon Order
Parting Off and Grooving Tool Holders-GST Series
External Diameter Tool Holder
Used for Sub-spindle of Automatic Lathe (Matching Thin Insert)
| Order No. | Dimensions (mm) | Matched | Screw | Wrench | Weight | In Stock | ||||||
| H=HF | B | CDX | CUTDIA | LF | WF | Insert |  |  | (KG) | R | L | |
| GSTSR/L1010JKA2-RS | 10 | 10 | 6 | 12 | 120 | 5 | SSAM040046Q TT10PQ 0.09 | |||||
| GSTSR/L1212JKA2-RS | 12 | 12 | 6 | 12 | 120 | 5 | GSTSAZR/L** | SSAM040046Q | TT10PQ | 0.14 | ● | ● |
| GSTSR/L1010JKB2-RS | 10 | 10 | 8 | 16 | 120 | 5 | GSTSB2R/L** | SSAM040046Q | TT10PQ | 0.09 | ● | ● |
| GSTSR/L1212JKB2-RS | 12 | 12 | 8 | 16 | 120 | 5 | SSAM040046Q | TT10PQ | 0.14 | ● | ● | |
Notes: SSAM040046Q representative M4.0X4.6
Stock OAvailable Upon Order
Stock OAvailable Upon Order
Recommended Cutting Data GT Series
Recommended Cutting Data GT Series
Recommended Cutting Data GK Series
Recommended Cutting Data
GB series
| ISO | WorkpieceMaterial | fn(mm/r) | ||||
| CW (mm) | ||||||
| 0.33-1.0 | 1.0-2.0 | 2.5-3.0 | 3.3-4.0 | 4.0-4.3 | ||
 | ①.0.04~0.09Carbon steel ①.0.03~0.08②.0.04~0.09 | ①.0.05~0.10②.0.05~0.10 | ①.0.05~0.12 | ①.0.05~0.12②.0.05~0.10 | ||
| ②.0.05~0.10 | ||||||
| Alloy steel | ①.0.03~0.07 | ①.0.04~0.08②.0.04~0.08 | ①.0.05~0.09②.0.05~0.09 | ①.0.05~0.10②.0.05~0.10 | ①.0.05~0.10②.0.05~0.10 | |
 | Stainless steel | ①.0.03~0.07 | ①.0.04~0.08②.0.04~0.08 | ①.0.05~0.09②.0.05~0.09 | ①.0.05~0.10②.0.05~0.10 | ①.0.05~0.10②.0.05~0.10 |
 | Cast iron | ①.0.03~0.08 | ①.0.04~0.09②.0.04~0.09 | ①.0.05~0.10②.0.05~0.10 | ①.0.05~0.12②.0.05~0.10 | ①.0.05~0.12②.0.05~0.10 |
① Radial Infeed② Axial infeed
GN series
| CW (mm) | f(mm/r) |
| 0.50-1.50 | 0.08 (0.03-0.12) |
| 1.50-2.50 | 0.10 (0.04-0.16) |
| 2.50-3.50 | 0.12 (0.05-0.20) |
| 3.50-4.80 | 0.14 (0.05-0.25) |
GST series
| ISO | Workpiece Material | Hardness (HB) | Series | fn(mm/r) |
 | Steel | ≤300 | GSTC | 0.02(0.01-0.03) |
| GSTS | 0.02(0.01-0.03) | |||
 | Stainless steel | ≤300 | GSTC | 0.015(0.01-0.02) |
| GSTS | 0.015(0.01-0.02) |
Recommended Cutting Data
| ISO | WorkpieceMaterial | Hard-ness(HB) | Cutting SpeedVc (m/min) | |||||||||
| G2230 | GP225 | G20 | GAA4230 | G30 | GA25 | GA15 | GS35 | GK15 | GS15 | |||
 | CarbonSteel | 80-250 | 100(60-165) | 120(80-220) | 140(100-250) | 110(70-180) | 110(70-180) | 100(60-160) | 105(70-170) | 115(80-190) | 150(110-260) | 120(90-200) |
| Low AlloySteel | 140-260 | 95(45-155) | 110(60-180) | 130(80-230) | 105(50-165) | 105(50-165) | 95(45-150) | 100(55-160) | 110(60-170) | 140(90-240) | 115(70-185) | |
| High AlloySteel | 180-300 | 90(45-145) | 110(60-180) | 120(80-220) | 100(50-150) | 100(50-150) | 90(45-140) | 95(50-150) | 105(60-160) | 130(80-230) | 110(65-170) | |
| Cast Steel | 180-300 | 80(40-125) | 110(60-180) | 110(45-180) | 90(40-130) | 90(40-130) | 80(40-120) | 85(40-120) | 95(40-150) | 115(50-190) | 100(40-150) | |
 | FerriticMartensitic | 150-270 | 100(50-150) | 100(50-150) | 90(45-130) | 95(50-110) | 105(60-160) | 110(65-170) | ||||
| Austenitic | 150-270 | 105(50-165) | 105(50-165) | 95(45-140) | 100(50-165) | 110(60-165) | 115(70-180) | |||||
 | MalleableCast Iron | 150-230 | 130(95-230) | 105(65-175) | 105(65-175) | 110(75-185) | 140(100-240) | 115(85-195) | ||||
| Grey CastIron | 150-230 | 120(95-215) | 100(55-160) | 100(55-160) | 105(65-165) | 130(100-230) | 110(75-180) | |||||
| NodularCast Iron | 160-260 | 110(70-210) | 95(45-145) | 95(45-145) | 100(55-155) | 120(70-220) | 105(60-165) | |||||
 | High-tem-peratureAlloy | 130-400 | 30(15-60) | 30(15-60) | 35(15-60) | 40(30-70) | ||||||
| TitaniumAlloy | 130-400 | 30(20-60) | 30(20-60) | 35(20-60) | 40(35-70) | |||||||
Type Representation Rules for Thread Turning Inserts
16
E
R
1.50
ISO - TC
①
②
③
④
⑤
① Insert Size
| Code | IC(mm) |
| 08 | 5 |
| 11 | 6.35 |
| 16 | 9.525 |
| 22 | 12.7 |
| 27 | 15.875 |
② Thread Type
③ Insert Direction
④ Pitch
E=External Thread
I=Internal Thread
=internal and External Threads
R=Right-handed
L=Left-hand
=Left/Right-handed
| Fully Thread Profile PitchRange | ||
| mm | TPI | |
| 0.35-5.0 | 72-5 | |
| Partial Thread Profile PitchRange | ||
| Code | mm | TPI |
| A | 0.5-1.5 | 48-16 |
| AG | 0.5-3.0 | 48-8 |
| G | 1.75-3.0 | 14-8 |
| N | 3.5-5.0 | 7-5 |
⑤ Thread Standard
⑥ Additional Information
| 60=60° General Thread | ACME=American TrapezoidalThread |
| 55=55° General Thread | STACME=American Short ToothTrapezoidal Thread |
| ISO=ISO Metric Screw Thread | ABUT=American SerratedThread |
| UN=American Unified Thread | BBUT=British Serrated Thread |
| W=British Whitworth Thread | SAGE=Metric Serrated Thread |
| NPT=American NationalStandard Taper Pipe Thread | API=API Standard Thread |
| NPTF=National (American)Pipe Thread | BUT=API Buttress Thread |
| BSPT=British NationalStandard Taper Pipe Thread | APIRD=API Round Thread forCasing and Tubing |
| RD=Round Thread DIN405 | MJ=Metric Aerospace Thread |
| RD20400=Round Thread20400 | UNJ=American AerospaceThread |
| TR=Metric Trapezoidal Thread | PG=German Standard PGThread |
Used to Define the Number of Teeth or Geometry, etc.
Type Representation Rules for Thread Turning Inserts GN Series Insert
GN
T
P
3
R
①
②
③
④
⑤
① Series Name
② Machining Type
③ Additional Information
GN
T=60° General Threading
P=Positive Rake Angle
=No Rake Angle
④ Insert Thickness
2=3.81mm
⑤ Insert Direction
R=Right-handed
3=4.95mm
L=Left-hand
Type Representation Rules for Thread Turning Inserts GST Series Insert
GSTT
3
R
A
60
005
①
②
④】
⑤
① Series Name
② Insert Thickness
③ Insert Direction
GSTT
3=3.0mm
R=Right-handed
L=Left-hand
④ Tip Offset Direction
A=Left-biased
⑤ Thread Standard
⑥ Crest Arc Size
60=60° General Thread
005=0.05mm
B=Right-biased
55=55° General Thread
Type Representation Rules for Thread Turning Tool Holders
2525
16
\- A16
①
②
④】
⑤】
⑦】
8
① Clamping Type
S=Clamping Type by Screw
⑤ Length of Tool Holder
C=Clamping Type by Clamp Plate
| Code | Length |
| F | 80 mm |
| H | 100 mm |
| K | 125 mm |
| M | 150 mm |
| N | 160 mm |
| P | 170 mm |
| Q | 180 mm |
| R | 200 mm |
| S | 250 mm |
| T | 300 mm |
| U | 350 mm |
| V | 400 mm |
② Machining Type
E=External Machining
I=Internal Hole Making
⑥ Insert Size
③ Tool Direction
| Code | Insert IC Value |
| 08 | 5 mm |
| 11 | 6.35 mm |
| 16 | 9.525 mm |
| 22 | 12.7 mm |
| 27 | 15.875 mm |
R=Right-handed
L=Left-hand
⑦ Tool Holder Material
| A | Steel Tool Holder withCooling Hole |
| C | Cemented Carbide ToolHolder |
| E | Cemented Carbide ToolHolder with Cooling Hole |
| ■ | Steel Tool Holder |
④ Shank Size
External Diameter Tool
Holder: Height\*width
Tool Holder with Internal
Hole Shank Diameter
(Example: 0025=Diameter
25mm)
⑧ Additional Information
| Tool Holder with Internal | A16= Shank Diameter Reinforced-Diameter 16mm |
Type Representation Rules for Thread Turning Tool Holders GN Series Tool Holder
GN
S
R
2525
M
3
①]
@
③
⑤
① Series Name
GN
② Machining Type
| ExternalMachining | S=Linear |
| E=Vertical | |
| R=Grinding Undercut | |
| Internal HoleMaking | A=Vertical InternalCooling |
③ Tool Direction
④ Shank Size
L=Left-hand
R=Right-handed
⑥ Insert Thickness
External Diameter Tool Holder: Height\*Width
Tool Holder with Internal Hole Shank Diameter
2=3.81mm
| ⑤ Length of Tool Holder | |
| Code | Length |
| D | 60 mm |
| E | 70 mm |
| F | 80 mm |
| H | 100 mm |
| K | 125 mm |
| M | 150 mm |
| P | 170 mm |
| Q | 180 mm |
| R | 200 mm |
3=4.95mm
| Code | Length |
| JK | 120 mm |
Type Representation Rules for Thread Turning Tool Holders GST Series Tool Holder
GSTS
1212
JK
2-RS
0]
③
④]
0]
① Series Name
② Insert Direction
③ Shank Size
④ Length of Tool Holder
GST
R=Right-handed
External Diameter Tool Holder: Height\*Width
GSTS (thin)
L=Left-hand
N=Middle
⑤ Insert Size
⑥ Insert Thickness
⑦ Additional Information
Unique to the GSTS Series
| A | Insert Height=8.7mm |
| B | Insert Height=9.5mm |
2=2.2mm
RS=Sub-spindle Tool Holder
3=3.0mm
4=4.0mm
List of Thread Turning Inserts
| Application fieldsThreads for GeneralMachinery Industry | Thread Type | Thread Diagram | Thread Code | Pitch | Page No. |
| 60° General Thread |  | 60 | 0.5-5.0(mm) | P272, P295, P296 | |
| 55° General Thread |  | 55 | 48-5(TPI) | P273, P296 | |
| ISO Metric ScrewThread |  | ISO | 0.4-6.0(mm) | P274-P275 | |
| UN Thread |  | UN | 24-7(TPI) | P276 | |
| Threads for Pipe Installationand Connection | Whitworth Thread |  | W | 19-8(TPI) | P277 |
| NPT Thread |  | NPT | 27 | P278 | |
| NPTF Thread |  | NPTF | 18-11.5(TPI) | P279 | |
| BSPT Thread |  | BSPT | 28-11(TPI) | P280 | |
| Round Thread(DIN405) |  | RD | 10-4(TPI) | P281 | |
| Round Thread(DIN20400) |  | RD20400 | 3.0-4.0(mm) | P282 |
Notes: In the thread diagram, the blue color represents the internal thread, while the gray color represents the external thread.
List of Thread Turning Inserts
| Application fields | Thread Type | Thread Diagram | Thread Code | Pitch | Page No. | |
| Transmission Thread | TR Thread |  | TR | 1.5-7.0(mm) | P283 | |
| ACME Thread |  | ACME | 1P4 | P284 | ||
| STACME Thread |  | STACME | 16-3(TPI) | P285 | ||
| SAGE Thread |  | SAGE | 2.0-4.0(mm) | P286 | ||
| ABUT Thread |  | ABUT | 20 | P287 | ||
| BBUT Thread |  | BBUT | 16P )0 | P288 | ||
| Threads for PetroleumIndustry | API Thread |  | API | (P) | P289 | |
| APIRD Thread |  | APIRD | 10-8(TPI) | P290 | ||
| Threads for AerospaceIndustry | MJ Thread |  | MJ | 1.0-3.0(mm) | P291 | |
| UNJ Thread |  | UNJ | 32-8(TPI)) | P292-P293 | ||
| Threads for Electric Industry | PG Thread |  | PG | 20-16(TPI) | P294 | |
Notes: In the thread diagram, the blue color represents the internal thread, while the gray color represents the external thread.
60° General Thread
▶External Thread
| Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
 | 16ERA60-TC | 0.5-1.5 | 0.8 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | |
| 16ERAG60-TC | 0.5-3.0 | 1.1 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ERG60-TC | 1.75-3.0 | 1.2 | 1.7 | 0.25 | 9.525 | 3.47 | 4 | ● | ● | ||
| 22ERN60-TC | 3.5-5.0 | 1.7 | 2.5 | 0.51 | 12.7 | 4.71 | 5 | ● | ● | ||
 | 16ELAG60 | 0.5-3.0 | 1.1 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | O | ||
●StockOAvailable Upon Order
60° General Thread
▶Internal Thread
| Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 08IRA60-TC | 0.5-1.5 | 0.6 | 0.7 | 0.08 | 5.00 | 2.25 | 2.68 | ● | ● | ||
| 11IRA60-TC | 0.5-1.5 | 0.8 | 0.9 | 0.08 | 6.35 | 3.00 | 3.2 | ● | |||
| 16IRA60-TC | 0.5-1.5 | 0.8 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IRAG60-TC | 0.5-3.0 | 1.1 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IRG60-TC | 1.75-3.0 | 1.2 | 1.7 | 0.13 | 9.525 | 3.47 | 4 | ● | ● | ||
| 22IRN60-TC | 3.5-5.0 | 1.7 | 2.5 | 0.25 | 12.7 | 4.71 | 5 | ● | |||
| 08ILA60 | 0.5-1.5 | 0.6 | 0.7 | 0.08 | 5.00 | 2.25 | 2.68 | ● | |||
| 22IRN60 | 3.5-5.0 | 1.8 | 2.5 | 0.36 | 12.7 | 4.71 | 5 | ● | |||
Stock OAvailable Upon Order
55° General Thread External Thread
| Order No. | Pitch (TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 GM3325 | ||||
 | 16ERA55-TC | 48-16 | 0.8 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | |||
| 16ERAG55-TC | 48-8 | 1.1 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ||||
| 16ERG55-TC | 14-8 | 1.2 | 1.7 | 0.21 | 9.525 | 3.47 | 4 | ||||
| 22ERN55-TC | 7-5 | 1.7 | 2.5 | 0.44 | 12.7 | 4.71 | 5 | ||||
StockOAvailable Upon Order
55° General Thread ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IRA55-TC | 48-16 | 0.8 | 0.9 | 0.08 | 6.35 | 3.00 | 3.2 | ||||
| 16IRA55-TC | 48-16 | 0.8 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IRAG55-TC | 48-8 | 1.1 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IRG55-TC | 14-8 | 1.2 | 1.7 | 0.21 | 9.525 | 3.47 | 4 | ● | ● | ||
| 22IRN55-TC | 7-5 | 1.7 | 2.5 | 0.44 | 12.7 | 4.71 | 5 | ● | ● | ||
| 08IRA55 | 48-16 | 0.6 | 0.7 | 0.08 | 5 | 2.25 | 2.68 | ||||
Stock OAvailable Upon Order
ISO Metric Screw Thread
▶ External Thread
Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 16ER1.00ISO-TC | 1.00 | 0.8 | 0.7 | 0.14 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER1.25ISO-TC | 1.25 | 0.8 | 0.9 | 0.18 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER1.50ISO-TC | 1.50 | 0.8 | 1.0 | 0.22 | 9.525 | 3.47 | 4 | ● | |||
| 16ER1.75ISO-TC | 1.75 | 1.2 | 1.2 | 0.25 | 9.525 | 3.47 | 4 | ||||
| 16ER2.00ISO-TC | 2.00 | 1.2 | 1.3 | 0.29 | 9.525 | 3.47 | 4 | ● | |||
| 16ER2.50ISO-TC | 2.50 | 1.2 | 1.5 | 0.36 | 9.525 | 3.47 | 4 | ||||
| 16ER3.00ISO-TC | 3.00 | 1.2 | 1.5 | 0.43 | 9.525 | 3.47 | 4 | ||||
| 22ER3.50ISO-TC | 3.50 | 1.6 | 2.3 | 0.45 | 12.7 | 4.71 | 5 | ● | |||
| 22ER4.00ISO-TC | 4.00 | 1.6 | 2.3 | 0.52 | 12.7 | 4.71 | 5 | ||||
| 22ER4.50ISO-TC | 4.50 | 1.7 | 2.4 | 0.58 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22ER5.00ISO-TC | 5.00 | 1.7 | 2.5 | 0.63 | 12.7 | 4.71 | 5 | ● | |||
| 22ER5.50ISO-TC | 5.50 | 1.9 | 2.7 | 0.72 | 12.7 | 4.71 | 5 | ● | |||
| 22ER6.00ISO-TC | 6.00 | 1.9 | 2.7 | 0.78 | 12.7 | 4.71 | 5 | O | ● | ||
 | 16ER0.40ISO | 0.40 | 0.6 | 0.5 | 0.06 | 9.525 | 3.47 | 4 | O | ||
| 16ER0.50ISO | 0.50 | 0.6 | 0.5 | 0.10 | 9.525 | 3.47 | 4 | ● | |||
| 16ER0.70ISO | 0.70 | 0.8 | 0.7 | 0.10 | 9.525 | 3.47 | 4 | O | |||
| 16ER0.75ISO | 0.75 | 0.8 | 0.7 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16ER0.80ISO | 0.80 | 0.6 | 0.6 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16ER1.00ISO | 1.00 | 0.7 | 0.6 | 0.11 | 9.525 | 3.47 | 4 | ● | |||
| 16EL1.00ISO | 1.00 | 0.7 | 0.7 | 0.14 | 9.525 | 3.47 | 4 | ||||
| 16ER1.25ISO | 1.25 | 0.8 | 0.9 | 0.18 | 9.525 | 3.47 | 4 | O | |||
| 16EL1.50ISO | 1.50 | 0.8 | 1.0 | 0.22 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER1.75ISO | 1.75 | 1.0 | 1.2 | 0.25 | 9.525 | 3.47 | 4 | O | |||
| 16EL2.00ISO | 2.00 | 1.2 | 1.3 | 0.29 | 9.525 | 3.47 | 4 | ● | ● | ||
| 22ER4.00ISO | 4.00 | 1.6 | 2.3 | 0.57 | 12.7 | 4.71 | 5 | O | |||
StockOAvailable Upon Order
ISO Metric Screw Thread
▶Internal Thread
Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR1.00ISO-TC | 1.00 | 0.8 | 0.7 | 0.07 | 6.35 | 3.00 | 3.2 | ● | ● | ||
| 11IR1.25ISO-TC | 1.25 | 0.8 | 0.9 | 0.09 | 6.35 | 3.00 | 3.2 | ● | ● | ||
| 11IR1.50ISO-TC | 1.50 | 0.8 | 1.0 | 0.11 | 6.35 | 3.00 | 3.2 | ● | ● | ||
| 11IR1.75ISO-TC | 1.75 | 0.9 | 1.1 | 0.13 | 6.35 | 3.00 | 3.2 | ● | ● | ||
| 11IR2.00ISO-TC | 2.00 | 0.9 | 1.1 | 0.15 | 6.35 | 3.00 | 3.2 | ● | |||
| 16IR1.00ISO-TC | 1.00 | 0.8 | 0.7 | 0.07 | 9.525 | 3.47 | 4 | ||||
| 16IR1.25ISO-TC | 1.25 | 0.8 | 0.9 | 0.09 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR1.50ISO-TC | 1.50 | 0.8 | 1.0 | 0.11 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR1.75ISO-TC | 1.75 | 1.2 | 1.2 | 0.13 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR2.00ISO-TC | 2.00 | 1.2 | 1.3 | 0.15 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR2.50ISO-TC | 2.50 | 1.2 | 1.5 | 0.18 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR3.00ISO-TC | 3.00 | 1.2 | 1.5 | 0.22 | 9.525 | 3.47 | 4 | ||||
| 22IR3.50ISO-TC | 3.50 | 1.6 | 2.3 | 0.22 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22IR4.00ISO-TC | 4.00 | 1.6 | 2.3 | 0.25 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22IR4.50ISO-TC | 4.50 | 1.6 | 2.4 | 0.28 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22IR5.00ISO-TC | 5.00 | 1.6 | 2.3 | 0.32 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22IR5.50ISO-TC | 5.50 | 1.6 | 2.3 | 0.36 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22IR6.00ISO-TC | 6.00 | 1.6 | 2.4 | 0.39 | 12.7 | 4.71 | 5 | ● | ● | ||
 | 11IR0.75ISO | 0.75 | 0.6 | 0.6 | 0.04 | 6.35 | 3 | 3.2 | O | ||
| 11IL1.50ISO | 1.50 | 0.8 | 1.0 | 0.11 | 6.35 | 3 | 3.2 | O | |||
| 11IR1.50ISO | 1.50 | 0.8 | 1.0 | 0.109 | 6.35 | 3 | 3.2 | ● | |||
| 16IR0.50ISO | 0.50 | 0.6 | 0.4 | 0.03 | 9.525 | 3.47 | 4 | ● | |||
| 16IR0.75ISO | 0.75 | 0.6 | 0.6 | 0.04 | 9.525 | 3.47 | 4 | O | |||
| 16IL1.00ISO | 1.00 | 0.6 | 0.7 | 0.07 | 9.525 | 3.47 | 4 | O | |||
| 16IR1.50ISO | 1.50 | 0.8 | 1.0 | 0.11 | 9.525 | 3.47 | 4 | O | |||
| 16IL1.50ISO | 1.50 | 0.8 | 1.0 | 0.11 | 9.525 | 3.47 | 4 | ● | |||
| 16IR2.00ISO | 2.00 | 1.0 | 1.3 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16IL2.00ISO | 2.00 | 1.0 | 1.3 | 0.15 | 9.525 | 3.47 | 4 | ● | |||
| 16IL3.00ISO | 3.00 | 1.2 | 1.5 | 0.22 | 9.525 | 3.47 | 4 | O | |||
| 22IL4.00ISO | 4.00 | 1.6 | 2.3 | 0.25 | 12.7 | 4.71 | 5 | O | |||
Stock OAvailable Upon Order
UN External Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 16ER24UN-TC | 24 | 0.8 | 0.8 | 0.15 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER20UN-TC | 20 | 0.8 | 0.9 | 0.18 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER18UN-TC | 18 | 0.8 | 1.0 | 0.20 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER16UN-TC | 16 | 0.9 | 1.1 | 0.23 | 9.525 | 3.47 | 4 | ||||
| 16ER14UN-TC | 14 | 1.2 | 1.5 | 0.26 | 9.525 | 3.47 | 4 | ||||
| 16ER12UN-TC | 12 | 1.2 | 1.5 | 0.31 | 9.525 | 3.47 | 4 | ● | |||
| 16ER9UN-TC | 9 | 1.2 | 1.7 | 0.42 | 9.525 | 3.47 | 4 | ||||
| 16ER8UN-TC | 8 | 1.3 | 1.7 | 0.46 | 9.525 | 3.47 | 4 | ● | ● | ||
 | 16ER20UN | 20 | 0.8 | 0.9 | 0.18 | 9.525 | 3.47 | 4 | O | ||
| 16ER10UN | 10 | 1.2 | 1.6 | 0.41 | 9.525 | 3.47 | 4 | ● | |||
| 22ER7UN | 7 | 1.6 | 2.3 | 0.47 | 12.7 | 4.71 | 5 | O | |||
Stock OAvailable Upon Order
▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| R | 11IR20UN-TC | 20 | 0.8 | 0.9 | 0.09 | 6.35 | 3.00 | 3.2 | ● | ● | |
| 11IR18UN-TC | 18 | 0.8 | 1.0 | 0.10 | 6.35 | 3.00 | 3.2 | ● | |||
| 16IR24UN-TC | 24 | 0.8 | 0.8 | 0.08 | 9.525 | 3.47 | 4 | ||||
| 16IR20UN-TC | 20 | 0.8 | 0.9 | 0.09 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR18UN-TC | 18 | 0.8 | 1.0 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16IR16UN-TC | 16 | 0.9 | 1.1 | 0.12 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR14UN-TC | 14 | 1.2 | 1.5 | 0.13 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR12UN-TC | 12 | 1.2 | 1.5 | 0.16 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR8UN-TC | 8 | 1.3 | 1.7 | 0.23 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR10UN | 10 | 1.1 | 1.5 | 0.183 | 9.525 | 3.47 | 4 | ● | |||
StockOAvailable Upon Order
▶External Thread
W
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 16ER19W-TC | 19 | 0.8 | 1.0 | 0.17 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER18W-TC | 18 | 0.8 | 1.0 | 0.18 | 9.525 | 3.47 | 4 | O | O | ||
| 16ER16W-TC | 16 | 0.9 | 1.1 | 0.20 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER14W-TC | 14 | 1.2 | 1.5 | 0.24 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER12W-TC | 12 | 1.2 | 1.5 | 0.28 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER11W-TC | 11 | 1.2 | 1.5 | 0.30 | 9.525 | 3.47 | 4 | ● | |||
| 16ER10W-TC | 10 | 1.1 | 1.5 | 0.34 | 9.525 | 3.47 | 4 | ● | O | ||
| 16ER8W | 8 | 1.2 | 1.5 | 0.41 | 9.525 | 3.47 | 4 | O | |||
●StockOAvailable Upon Order
W
▶Internal Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR19W-TC | 19 | 0.9 | 1.1 | 0.19 | 6.35 | 3.00 | 3.2 | ● | ● | ||
| 11IR14W-TC | 14 | 0.9 | 1.1 | 0.27 | 6.35 | 3.00 | 3.2 | ||||
| 16IR19W-TC | 19 | 0.8 | 1.0 | 0.17 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR18W-TC | 18 | 0.8 | 1.0 | 0.18 | 9.525 | 3.47 | 4 | ● | O | ||
| 16IR16W-TC | 16 | 0.9 | 1.1 | 0.20 | 9.525 | 3.47 | 4 | ● | O | ||
| 16IR14W-TC | 14 | 1.2 | 1.5 | 0.24 | 9.525 | 3.47 | 4 | ||||
| 16IR12W-TC | 12 | 1.2 | 1.5 | 0.28 | 9.525 | 3.47 | 4 | ||||
| 16IR11W-TC | 11 | 1.2 | 1.5 | 0.30 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR8W-TC | 8 | 1.2 | 1.5 | 0.41 | 9.525 | 3.47 | 4 | ● | |||
Stock OAvailable Upon Order
NPT ▶External Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 16ER27NPT-TC | 27 | 0.7 | 0.8 | 0.13 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER18NPT-TC | 18 | 0.8 | 1.0 | 0.20 | 9.525 | 3.47 | 4 | ● | |||
| 16ER14NPT-TC | 14 | 1.2 | 1.5 | 0.22 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16ER11.5NPT-TC | 11.5 | 1.2 | 1.5 | 0.25 | 9.525 | 3.47 | 4 | ● | |||
| 16ER8NPT-TC | 8 | 1.3 | 1.8 | 0.30 | 9.525 | 3.47 | 4 | ● | |||
| 16ER27NPT | 27 | 0.07 | 0.7 | 0.80 | 9.525 | 3.47 | 4 | ||||
| 16ER18NPT | 18 | 0.8 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16ER14NPT | 14 | 1.2 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ||||
| 16ER11.5NPT 11.5 | 1.2 | 1.5 | 0.091 | 9.525 | 3.47 | 4 | |||||
Stock OAvailable Upon Order
NPT ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
 | 11IR18NPT-TC | 18 | 0.8 | 1.0 | 0.20 | 6.35 | 3.00 | 3.2 | ● | ● | |
| 16IR27NPT-TC | 27 | 0.7 | 0.8 | 0.13 | 9.525 | 3.47 | 4 | O | O | ||
| 16IR18NPT-TC | 18 | 0.8 | 1.0 | 0.20 | 9.525 | 3.47 | 4 | ● | |||
| 16IR14NPT-TC | 14 | 1.2 | 1.5 | 0.22 | 9.525 | 3.47 | 4 | ● | ● | ||
| 16IR11.5NPT-TC | 11.5 | 1.2 | 1.5 | 0.25 | 9.525 | 3.47 | 4 | ||||
| 16IR8NPT-TC | 8 | 1.3 | 1.8 | 0.30 | 9.525 | 3.47 | 4 | ||||
 | 11IR18NPT | 18 | 0.8 | 1.1 | 0.081 | 6.35 | 3 | 3.2 | ● | ||
| 11IL18NPT | 18 | 0.8 | 1.1 | 0.081 | 6.35 | 3 | 3.2 | ||||
| 16IR14NPT | 14 | 1.2 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | ||||
| 16IR11.5NPT | 11.5 | 1.2 | 1.5 | 0.107 | 9.525 | 3.47 | 4 | ||||
StockOAvailable Upon Order
NPTF ▶External Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16ER18NPTF | 18 | 0.8 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16ER14NPTF | 14 | 1.0 | 1.2 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16ER11.5NPTF | 11.5 | 1.2 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | O | |||
StockOAvailable Upon Order
NPTF ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16IR18NPTF | 18 | 0.8 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR14NPTF | 14 | 1.0 | 1.2 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR11.5NPTF | 11.5 | 1.2 | 1.5 | 0.08 | 9.525 | 3.47 | 4 | 0 | |||
StockOAvailable Upon Order
BSPT ▶External Thread
| Order No. | Pitch (TPI) | Dimensions (mm) | GM3325 | Coated Cemented Carbide | ||||||
| PDY | PDX | RE | IC S | D1 | GM3215 GM3225 | |||||
| 16ER28BSPT-TC | 28 | 0.7 | 0.8 | 0.11 | 9.525 | 3.47 | 4 | |||
| 16ER19BSPT-TC | 19 | 0.8 | 1.0 | 0.17 | 9.525 | 3.47 | 4 | |||
| 16ER14BSPT-TC | 14 | 1.2 | 1.5 | 0.24 | 9.525 | 3.47 | 4 | |||
| 16ER11BSPT-TC | 11 | 1.2 | 1.5 | 0.30 | 9.525 | 3.47 | 4 | |||
●Stock OAvailable Upon Order
BSPT ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
 | 11IR19BSPT-TC | 19 | 0.8 | 1.0 | 0.18 | 6.35 | 3.00 | 3.2 | ● | ● | |
| 11IR14BSPT-TC | 14 | 0.9 | 1.1 | 0.24 | 6.35 | 3.00 | 3.2 | ● | |||
| 16IR28BSPT-TC | 28 | 0.7 | 0.8 | 0.11 | 9.525 | 3.47 | 4 | O | O | ||
| 16IR19BSPT-TC | 19 | 0.8 | 1.0 | 0.17 | 9.525 | 3.47 | 4 | ● | |||
| 16IR14BSPT-TC | 14 | 1.2 | 1.5 | 0.24 | 9.525 | 3.47 | 4 | ||||
| 16IR11BSPT-TC | 11 | 1.2 | 1.5 | 0.30 | 9.525 | 3.47 | 4 | · | |||
 | 16IR11BSPT | 11 | 1.2 | 1.5 | 0.32 | 9.525 | 3.47 | 4 | ● | ||
Stock OAvailable Upon Order
▶External Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 G | M3225 G | M3325 | |||
 | 16ER8RD-TC | 8 | 1.4 | 1.3 | 0.75 | 9.525 | 3.47 | 4 | ● | O | |
| 16ER6RD-TC | 6 | 1.4 | 1.5 | 1.00 | 9.525 | 3.47 | 4 | ● | O | ||
| 16ER10RD | 10 | 1.1 | 1.2 | 0.609 | 9.525 | 3.47 | 4 | O | |||
| 22ER4RD | 4 | 2.2 | 2.3 | 1.52 | 12.7 | 4.71 | 5 | ● | ● | ||
Stock OAvailable Upon Order
RD(DIN405)
▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 16IR8RD-TC | 8 | 1.4 | 1.3 | 0.70 | 9.525 | 3.47 | 4 | O | |||
| 16IR6RD-TC | 6 | 1.4 | 1.5 | 0.936 | 9.525 | 3.47 | 4 | ● | O | ||
| 16IR10RD | 10 | 1.1 | 1.2 | 0.564 | 9.525 | 3.47 | 4 | O | |||
| 22IR4RD | 4 | 2.2 | 2.3 | 1.44 | 12.7 | 4.71 | 5 | ● | ● | ||
Stock OAvailable Upon Order
RD(DIN20400)
▶External Thread
| Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
22ER3.0RD20400 3.022ER4.0RD20400 | 1.3 | 1.7 | 0.66 | 12.7 | 4.71 | 5 | O | ||||
| 1.6 | 2.2 | 0.88 | 12.7 | 4.71 | 5 | O | |||||
Stock OAvailable Upon Order
RD(DIN20400) ▶Internal Thread
| Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
22IR3.0RD20400 3.0 | 1.3 | 1.7 | 0.66 | 12.7 | 4.71 | 5 | O | ||||
Stock OAvailable Upon Order
TR ▶External Thread
Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11ER1.5TR | 1.5 | 1.0 | 1.1 | 0.10 | 6.35 | 3 | 3.2 | O | |||
| 16ER1.5TR | 1.5 | 1.0 | 1.1 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16ER2.0TR | 2.0 | 1.1 | 1.3 | 0.18 | 9.525 | 3.47 | 4 | ● | |||
| 16ER3.0TR | 3.0 | 1.2 | 1.5 | 0.11 | 9.525 | 3.47 | 4 | ||||
| 22ER4.0TR | 4.0 | 1.7 | 1.9 | 0.25 | 12.7 | 4.71 | 5 | O | ● | ||
| 22ER5.0TR | 5.0 | 1.9 | 2.1 | 0.25 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22ER6.0TR | 6.0 | 1.9 | 2.1 | 0.25 | 12.7 | 4.71 | 5 | O | ● | ||
| 27ER6.0TR | 6.0 | 1.9 | 2.1 | 0.25 | 15.875 | 6.26 | 6.16 | O | |||
| 27ER7.0TR | 7.0 | 2.4 | 2.7 | 0.25 | 15.875 | 6.26 | 6.16 | O | |||
Stock OAvailable Upon Order
TR ▶Internal Thread
Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR1.5TR | 1.5 | 0.9 | 1.0 | 0.47 | 6.35 | 3 | 3.2 | O | |||
| 16IR1.5TR | 1.5 | 1.0 | 1.1 | 0.10 | 9.525 | 3.47 | 4 | ● | |||
| 16IR2.0TR | 2.0 | 1.0 | 1.3 | 0.18 | 9.525 | 3.47 | 4 | ● | |||
| 16IL3.0TR | 3.0 | 1.1 | 1.3 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16IR3.0TR | 3.0 | 1.1 | 1.3 | 0.15 | 9.525 | 3.47 | 4 | ● | |||
| 22IR4.0TR | 4.0 | 1.6 | 1.9 | 0.25 | 12.7 | 4.71 | 5 | ● | |||
| 22IR5.0TR | 5.0 | 1.84 | 2.2 | 0.25 | 12.7 | 4.71 | 5 | ● | |||
| 22IR6.0TR | 6.0 | 1.9 | 2.2 | 0.25 | 12.7 | 4.71 | 5 | ||||
| 27IR6.0TR | 6.0 | 1.9 | 2.2 | 0.25 | 15.875 | 6.276 | 6.16 | O | |||
| 27IR7.0TR | 7.0 | 2.5 | 2.8 | 0.25 | 15.875 | 6.15 | 6.16 | O | |||
Stock OAvailable Upon Order
ACME ▶External Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11ER16ACME | 16 | 0.9 | 1.0 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 16ER16ACME | 16 | 0.9 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16ER14ACME | 14 | 0.9 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16ER12ACME | 12 | 1.1 | 1.3 | 0.12 | 9.525 | 3.47 | 4 | ● | |||
| 16ER10ACME | 10 | 1.1 | 1.0 | 0.1 | 9.525 | 3.47 | 4 | ● | |||
| 16ER8ACME | 8 | 1.3 | 1.5 | 0.15 | 9.525 | 3.47 | 4 | ||||
| 16EL8ACME | 8 | 1.4 | 1.8 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16ER7ACME | 7 | 1.6 | 2.0 | 0.25 | 9.525 | 3.47 | 4 | O | |||
| 16ER6ACME | 6 | 1.6 | 1.8 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 22ER6ACME | 6 | 1.65 | 1.75 | 0.08 | 12.7 | 4.71 | 5 | O | ● | ||
| 22EL6ACME | 6 | 1.8 | 2.1 | 0.08 | 12.7 | 4.71 | 5 | O | |||
| 22ER5ACME | 5 | 2 | 2.2 | 0.12 | 12.7 | 4.71 | 5 | ● | ● | ||
| 27ER4ACME | 4 | 2.4 | 2.7 | 0.15 | 15.875 | 6.15 | 6.16 | ||||
StockOAvailable Upon Order
ACME ▶Internal Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR16ACME | 16 | 0.9 | 1.0 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 16IR16ACME | 16 | 1.0 | 1.1 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR14ACME | 14 | 0.9 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | 0 | |||
| 16IR12ACME | 12 | 1.1 | 1.3 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16IR10ACME | 10 | 1.2 | 1.3 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR8ACME | 8 | 1.4 | 1.8 | 0.15 | 9.525 | 3.47 | 4 | ● | |||
| 16IL8ACME | 8 | 1.4 | 1.8 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16IR7ACME | 7 | 1.6 | 1.9 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16IR6ACME | 6 | 1.6 | 1.8 | 0.11 | 9.525 | 3.47 | 4 | ● | |||
| 22IR6ACME | 6 | 1.65 | 1.8 | 0.11 | 12.7 | 4.71 | 5 | ● | |||
| 22IL6ACME | 6 | 1.8 | 2.1 | 0.11 | 12.7 | 4.71 | 5 | O | |||
| 22IR5ACME | 5 | 2 | 2.2 | 0.12 | 12.7 | 4.71 | 5 | ● | |||
| 27IR4ACME | 4 | 2.4 | 2.7 | 0.15 | 15.875 | 6.15 | 6.16 | ● | |||
Stock OAvailable Upon Order
STACME ▶External Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11ER16STACME | 16 | 0.9 | 1.0 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 16ER16STACME | 16 | 0.9 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16ER14STACME | 14 | 1.0 | 1.1 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16ER12STACME | 12 | 1.1 | 1.1 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16ER10STACME | 10 | 1.2 | 1.2 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16ER8STACME | 8 | 1.4 | 1.4 | 0.10 | 9.525 | 3.47 | 4 | ● | |||
| 16EL8STACME | 8 | 1.4 | 1.5 | 0.20 | 9.525 | 3.47 | 4 | O | |||
| 16ER6STACME | 6 | 1.5 | 1.5 | 0.11 | 9.525 | 3.47 | 4 | ● | |||
| 22ER6STACME | 6 | 1.7 | 1.9 | 0.11 | 12.7 | 4.71 | 5 | O | ● | ||
| 22EL6STACME | 6 | 1.7 | 1.9 | 0.11 | 12.7 | 4.71 | 5 | O | |||
| 22ER5STACME | 5 | 2.1 | 2.3 | 0.12 | 12.7 | 4.71 | 5 | O | |||
| 22ER4STACME | 4 | 2.15 | 2.4 | 0.27 | 12.7 | 4.71 | 5 | ● | |||
| 27ER4STACME | 4 | 2.4 | 2.7 | 0.27 | 15.875 | 6.15 | 6.16 | O | |||
| 27ER3STACME | 3 | 3 | 3.3 | 0.35 | 15.875 | 6.15 | 6.16 | O | |||
Stock OAvailable Upon Order
STACME
▶Internal Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR16STACME | 16 | 0.9 | 1.0 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 16IR16STACME | 16 | 0.9 | 1.0 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR14STACME | 14 | 1.0 | 1.1 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16IR12STACME | 12 | 1.1 | 1.1 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16IR10STACME | 10 | 1.2 | 1.3 | 0.10 | 9.525 | 3.47 | 4 | ||||
| 16IR8STACME | 8 | 1.2 | 1.1 | 0.1 | 9.525 | 3.47 | 4 | ● | |||
| 16IL8STACME | 8 | 1.2 | 1.1 | 0.1 | 9.525 | 3.47 | 4 | O | |||
| 16IR6STACME | 6 | 1.8 | 1.8 | 0.12 | 9.525 | 3.47 | 4 | ||||
| 22IR6STACME | 6 | 1.7 | 1.8 | 0.12 | 12.7 | 4.71 | 5 | O | ● | ||
| 22IL6STACME | 6 | 1.7 | 1.8 | 0.12 | 12.7 | 4.71 | 5 | O | |||
| 22IR5STACME | 5 | 2.1 | 2.3 | 0.12 | 12.7 | 4.71 | 5 | ● | |||
| 22IR4STACME | 4 | 2.3 | 2.4 | 0.27 | 12.7 | 4.71 | 5 | ● | |||
| 27IR4STACME | 4 | 2.4 | 2.7 | 0.27 | 15.875 | 6.15 | 6.16 | O | |||
| 27IR3STACME | 3 | 3.0 | 3.3 | 0.35 | 15.875 | 6.15 | 6.16 | O | |||
Stock OAvailable Upon Order
SAGE ▶External Thread
●Stock OAvailable Upon Order
SAGE ▶Internal Thread
SAGE ▶Internal Thread
| Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16ER2.0SAGE | 2.0 | 1.3 | 1.8 | 0.22 | 9.525 | 3.47 | 4 | O | |||
| 22ER3.0SAGE | 3.0 | 1.6 | 2.3 | 0.34 | 12.7 | 4.71 | 5 | 0 | |||
| 22ER4.0SAGE | 4.0 | 1.8 | 2.7 | 0.46 | 12.7 | 4.71 | 5 | ● | |||
| Order No. | Pitch (mm) | Dimensions (mm) | Coated Cemented Carbide | |||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 GM3225 GM3325 | ||||
| 16IR2.0SAGE | 2.0 | 1.5 | 1.9 | 0.12 | 9.525 | 3.47 | 4 | O | ||
22IR3.0SAGE  | 3.0 | 1.9 | 2.5 | 0.11 | 12.7 | 4.71 | 5 | O | ||
| 22IR4.0SAGE | 4.0 | 2.0 | 2.8 | 0.14 | 12.7 | 4.71 | 5 | 0 | ||
Stock OAvailable Upon Order
ABUT ▶External Thread
| Order No. | Pitch (TPI) | Dimensions (mm) | Coated Cemented Carbide | |||||||
| PDY | PDX | RE | IC | S | D1 GM3215 | GM3225 GM3325 | ||||
 | 16ER20ABUT | 20 | 1.0 | 1.3 | 0.08 | 9.525 | 3.47 | 4 | O | |
| 16ER16ABUT | 16 | 1.3 | 1.9 | 0.08 | 9.525 | 3.47 | 4 | O | ||
| 16ER12ABUT | 12 | 1.3 | 1.9 | 0.12 | 9.525 | 3.47 | 4 | O | ||
| 16ER10ABUT | 10 | 1.5 | 2.1 | 0.15 | 9.525 | 3.47 | 4 | O | ||
| 22ER8ABUT | 8 | 2.0 | 3.0 | 0.18 | 12.7 | 4.71 | 5 | 0 | ||
| 22ER6ABUT | 6 | 2.2 | 3.3 | 0.23 | 12.7 | 4.71 | 5 | O | ||
Stock OAvailable Upon Order
ABUT ▶Internal Thread
Order No.16IR20ABUT | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 20 | 1.0 | 1.3 | 0.08 | 9.525 | 3.47 | 4 | O | ||||
| 16IR16ABUT | 16 | 1.3 | 1.8 | 0.08 | 9.525 | 3.47 | 4 | ● | |||
| 16IR12ABUT | 12 | 1.4 | 2.0 | 0.12 | 9.525 | 3.47 | 4 | O | |||
| 16IR10ABUT | 10 | 15 | 2.2 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 22IR8ABUT | 8 | 2.0 | 3.0 | 0.18 | 12.7 | 4.71 | 5 | 0 | |||
| 22IR6ABUT | 6 | 2.2 | 3.3 | 018 | 12.7 | 4.71 | 5 | O | |||
●Stock OAvailable Upon Order
BBUT ▶External Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16ER16BBUT | 16 | 1.1 | 1.5 | 0.16 | 9.525 3.47 | 4 | O | ||||
| 16ER12BBUT | 12 | 1.3 | 1.9 | 0.22 | 9.525 | 3.47 | 4 | 0 | |||
| 16ER10BBUT | 10 | 1.4 | 2.0 | 0.27 | 9.525 | 3.47 | 4 | 0 | |||
| 16ER8BBUT | 8 | 1.6 | 2.2 | 0.35 | 9.525 | 3.47 | 4 | O | |||
Stock OAvailable Upon Order
BBUT ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
 | 16IR16BBUT | 16 | 1.1 | 1.5 | 0.16 | 9.525 | 3.47 | 4 | O | ||
| 16IR12BBUT | 12 | 1.3 | 1.9 | 0.22 | 9.525 | 3.47 | 4 | O | |||
| 16IR10BBUT | 10 | 1.4 | 2.0 | 0.27 | 9.525 | 3.47 | 4 | O | |||
| 16IR8BBUT | 8 | 1.6 | 2.2 | 0.35 | 9.525 | 3.47 | 4 | O | |||
OStock OAvailable Upon Order
API ▶External Thread
| Order No. | Pitch (TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
 | 22ER5API403 | 5 | 2.0 | 2.6 | 0.511 | 12.7 | 4.71 | 5 | O | ||
| 22ER4API382 | 4 | 2.1 | 2.8 | 0.971 | 12.7 | 4.71 | 5 | ● | ● | ||
| 22ER4API383 | 4 | 1.9 | 2.7 | 0.971 | 12.7 | 4.71 | 5 | O | O | ||
| 22ER4API502 | 4 | 1.9 | 2.8 | 0.639 | 12.7 | 4.71 | 5 | ● | |||
| 22ER4API503 | 4 | 2.1 | 2.7 | 0.639 | 12.7 | 4.71 | 5 | O | |||
StockOAvailable Upon Order
API ▶Internal Thread
Order No.22IR5API403 22IR4API503 4 | Dimensions (mm) | Coated Cemented Carbide | |||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 2.0 | 2.7 | 0.515 | 12.7 | 4.71 | 5 | ● | |||||
| 22IR4API382 | 2.1 | 2.8 | 0.979 | 12.7 | 4.71 | 5 | ● | ● | |||
| 22IR4API383 | 1.9 | 2.7 | 0.979 | 12.7 | 4.71 | 5 | O | O | |||
| 22IR4API502 | 2.0 | 2.7 | 0.644 | 12.7 | 4.71 | 5 | ● | ● | |||
| 2.0 | 2.8 0.644 12.7 4.71 | 5 | O | ||||||||
StockOAvailable Upon Order
API RD ▶External Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16ER10APIRD 10 | 1.48 | 1.5 | 0.435 | 9.525 3.47 4 | ● | ||||||
| 16ER8APIRD | 1.3 | 1.5 | 0.359 | 9.525 | 3.47 | 4 | ● | ● | |||
StockOAvailable Upon Order
API RD ▶Internal Thread
| Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
16IR10APIRD | 10 | 1.5 | 1.3 | 0.361 | 9.525 | 3.47 | 4 | ||||
| 16IR8APIRD | 8 | 1.5 | 1.3 | 0.438 | 9.525 | 3.47 | 4 | O | ● | ||
Stock OAvailable Upon Order
MJ ▶External Thread
| Order No. | Pitch (mm) | Dimensions (mm) | Coated Cemented Carbide | |||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 GM3225 GM3325 | ||||
 | 16ER1.00MJ | 1.00 | 0.6 | 0.7 | 0.165 | 9.525 | 3.47 | 4 | ||
| 16ER1.25MJ | 1.25 | 0.8 | 0.9 | 0.207 | 9.525 | 3.47 | 4 | |||
| 16ER1.50MJ | 1.50 | 0.8 | 1.1 | 0.24 | 9.525 | 3.47 | 4 | ● | ||
| 16EL1.50MJ | 1.50 | 0.8 | 1.1 | 0.24 | 9.525 | 3.47 | 4 | O | ||
| 16ER1.75MJ | 1.75 | 0.9 | 1.2 | 0.29 | 9.525 | 3.47 | 4 | O | ||
| 16ER2.00MJ | 2.00 | 1.0 | 1.3 | 0.33 | 9.525 | 3.47 | 4 | ● | ||
| 16ER2.50MJ | 2.50 | 1.1 | 1.5 | 0.41 | 9.525 | 3.47 | 4 | O | ||
| 16ER3.00MJ | 3.00 | 1.2 | 1.6 | 0.50 | 9.525 | 3.47 | 4 | O | ||
Stock OAvailable Upon Order
MJ ▶Internal Thread
Order No. | Pitch(mm) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR1.00MJ | 1.00 | 0.6 | 0.7 | 0.07 | 6.35 | 3 | 3.2 | O | |||
| 11IR1.25MJ | 1.25 | 0.8 | 0.9 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 11IR1.50MJ | 1.50 | 0.7 | 1.0 | 0.09 | 6.35 | 3 | 3.2 | O | |||
| 11IR2.00MJ | 2.00 | 1.0 | 1.3 | 0.13 | 6.35 | 3 | 3.2 | O | |||
| 16IR1.00MJ | 1.00 | 0.6 | 0.7 | 0.07 | 9.525 | 3.47 | 4 | ● | |||
| 16IR1.25MJ | 1.25 | 0.8 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | O | |||
| 16IR1.50MJ | 1.50 | 0.8 | 1.0 | 0.09 | 9.525 | 3.47 | 4 | O | |||
| 16IR2.00MJ | 2.00 | 1.0 | 1.3 | 0.13 | 9.525 | 3.47 | 4 | O | |||
| 16IR2.50MJ | 2.50 | 1.1 | 1.5 | 0.15 | 9.525 | 3.47 | 4 | 0 | |||
| 16IR3.00MJ | 3.00 | 1.2 | 1.6 | 0.18 | 9.525 | 3.47 | 4 | O | |||
Stock OAvailable Upon Order
UNJ ▶External Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11ER32UNJ | 32 | 0.6 | 0.7 | 0.13 | 6.35 | 3 | 3.2 | O | |||
| 11ER28UNJ | 28 | 0.6 | 0.7 | 0.15 | 6.35 | 3 | 3.2 | O | |||
| 11ER24UNJ | 24 | 0.6 | 0.7 | 0.18 | 6.35 | 3 | 3.2 | O | |||
| 11ER20UNJ | 20 | 0.7 | 0.9 | 0.21 | 6.35 | 3 | 3.2 | O | |||
| 11ER18UNJ | 18 | 0.8 | 1.0 | 0.23 | 6.35 | 3 | 3.2 | O | |||
| 11ER16UNJ | 16 | 0.8 | 1.0 | 0.25 | 6.35 | 3 | 3.2 | O | |||
| 11ER14UNJ | 14 | 1.0 | 1.2 | 0.30 | 6.35 | 3 | 3.2 | O | |||
| 16ER32UNJ | 32 | 0.6 | 0.7 | 0.13 | 9.525 | 3.47 | 4 | ● | |||
| 16ER28UNJ | 28 | 0.6 | 0.7 | 0.15 | 9.525 | 3.47 | 4 | ● | |||
| 16ER24UNJ | 24 | 0.6 | 0.7 | 0.175 | 9.525 | 3.47 | 4 | O | |||
| 16ER20UNJ | 20 | 0.7 | 0.9 | 0.21 | 9.525 | 3.47 | 4 | ● | |||
| 16ER18UNJ | 18 | 0.8 | 1.0 | 0.23 | 9.525 | 3.47 | 4 | ● | |||
| 16ER16UNJ | 16 | 0.8 | 1.0 | 0.263 | 9.525 | 3.47 | 4 | O | |||
| 16ER14UNJ | 14 | 1.0 | 1.2 | 0.30 | 9.525 | 3.47 | 4 | O | |||
| 16ER12UNJ | 12 | 1.0 | 1.2 | 0.35 | 9.525 | 3.47 | 4 | O | |||
| 16ER10UNJ | 10 | 1.1 | 1.4 | 0.42 | 9.525 | 3.47 | 4 | O | |||
| 16ER8UNJ | 8 | 1.4 | 1.7 | 0.54 | 9.525 | 3.47 | 4 | O | |||
Stock OAvailable Upon Order
UNJ ▶Internal Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR32UNJ | 32 | 0.6 | 0.6 | 0.025 | 6.35 | 3 | 3.2 | O | |||
| 11IR28UNJ | 28 | 0.6 | 0.7 | 0.05 | 6.35 | 3 | 3.2 | O | |||
| 11IR24UNJ | 24 | 0.6 | 0.8 | 0.05 | 6.35 | 3 | 3.2 | O | |||
| 11IR20UNJ | 20 | 0.7 | 0.9 | 0.07 | 6.35 | 3 | 3.2 | O | |||
| 11IR18UNJ | 18 | 0.8 | 1.0 | 0.07 | 6.35 | 3 | 3.2 | 0 | |||
| 11IR16UNJ | 16 | 0.8 | 1.0 | 0.07 | 6.35 | 3 | 3.2 | O | |||
| 11IR14UNJ | 14 | 1.0 | 1.2 | 0.1 | 6.35 | 3 | 3.2 | 0 | |||
| 16IR32UNJ | 32 | 0.6 | 0.6 | 0.05 | 9.525 | 3.47 | 4 | O | |||
| 16IR28UNJ | 28 | 0.5 | 0.7 | 0.05 | 9.525 | 3.47 | 4 | O | |||
| 16IR24UNJ | 24 | 0.6 | 0.8 | 0.05 | 9.525 | 3.47 | 4 | O | |||
| 16IR20UNJ | 20 | 0.7 | 0.9 | 0.07 | 9.525 | 3.47 | 4 | O | |||
| 16IR18UNJ | 18 | 0.8 | 1.0 | 0.07 | 9.525 | 3.47 | 4 | O | |||
| 16IR16UNJ | 16 | 0.8 | 1.0 | 0.07 | 9.525 | 3.47 | 4 | ● | |||
| 16IR14UNJ | 14 | 1.0 | 1.2 | 0.10 | 9.525 | 3.47 | 4 | O | |||
| 16IR12UNJ | 12 | 1.0 | 1.3 | 0.12 | 9.525 | 3.47 | 4 | 0 | |||
| 16IR10UNJ | 10 | 1.0 | 1.4 | 0.15 | 9.525 | 3.47 | 4 | O | |||
| 16IR8UNJ | 8 | 1.0 | 1.4 | 0.19 | 9.525 | 3.47 | 4 | O | |||
StockOAvailable Upon Order
PG ▶External Thread
| Order No. | Pitch (TPI) | Dimensions (mm) | Coated Cemented Carbide GM3325 | ||||||
| PDY | PDX | RE | IC | S D1 | GM3215 GM3225 | ||||
 | 16ER20PG | 20 | 0.8 | 0.9 0.14 | 9.525 | 3.47 | 4 | O | |
| 16ER18PG | 18 | 0.8 | 0.9 0.09 | 9.525 | 3.47 | 4 | O | ||
| 16ER16PG | 16 | 0.8 | 1.0 0.12 | 9.525 | 3.47 | 4 | O | ||
Stock OAvailable Upon Order
PG ▶Internal Thread
Order No. | Pitch(TPI) | Dimensions (mm) | Coated Cemented Carbide | ||||||||
| PDY | PDX | RE | IC | S | D1 | GM3215 | GM3225 | GM3325 | |||
| 11IR20PG | 20 | 0.7 | 0.9 | 0.08 | 6.35 | 3 | 3.2 | O | |||
| 11IR18PG | 18 | 0.8 | 1.0 | 0.09 | 6.35 | 3 | 3.2 | O | |||
| 11IR16PG | 16 | 0.8 | 1.0 | 0.12 | 6.35 | 3 | 3.2 | 0 | |||
| 16IR20PG | 20 | 0.7 | 0.9 | 0.08 | 9.525 | 3.47 | 4 | 0 | |||
| 16IR18PG | 18 | 0.8 | 1.0 | 0.09 | 9.525 | 3.47 | 4 | 0 | |||
| 16IR16PG | 16 | 0.8 | 1.0 | 0.12 | 9.525 | 3.47 | 4 | O | |||
●StockOAvailable Upon Order
GNTP
▶60° General Thread Inserts, with Rake Angle
| Order No. | InsertSpecifi-cations | Pitch | Dimensions (mm) | CoatedCementedCarbide | |||||
| ExternalThread(mm) | InternalThread(mm) | ExternalThread(TPI) | InternalThread(TPI) | RE | E | GM3225 | |||
GNTP2L | 2 | 0.70-3.00 | 1.25-3.50 | 8-36 | 7-20 | 0.10 | 1.91 | ||
| 2 | 0.70-3.00 | 1.25-3.50 | 8-36 | 7-20 | 0.10 | 1.91 | ● | ||
| 3 | 1.25-4.00 | 2.00-5.00 | 4-20 | 5-12 | 0.17 | 2.49 | ● | ||
| 3 | 1.25-4.00 | 2.00-5.00 | 4-20 | 5-12 | 0.17 | 2.49 | ● | ||
●Stock OAvailable Upon Order
GSTT Small Part Threading Inserts
Order No. | Pitch | Dimensions (mm) | CoatedCementedCarbide | ||||||||||
| mm | TPI | W1 | CW | S | D1 | RE | PDX | PDX1 | PNA | GA15 | GA25 | ||
| GSTT3LA6000 | 0.2-0.6 | 64-48 | 3 | 2.5 | 8.7 | 5.2 | - | 2.1 | 0.4 | 60° | ● | ● | |
| GSTT3LB6000 | 0.2-0.6 | 64-48 | 3 | 2.5 | 8.7 | 5.2 | - | 0.4 | 2.1 | 60° | ● | ● | |
| GSTT3LA60005 | 0.5-1.25 | 48-24 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 1.7 | 0.8 | 60° | ● | ● | |
| GSTT3LB60005 | 0.5-1.25 | 48-24 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 0.8 | 1.7 | 60° | ● | ● | |
| GSTT3LN6001 | 1-1.5 | 24-18 | 3 | 2.5 | 8.7 | 5.2 | 0.1 | 1.25 | 1.25 | 60° | ● | ● | |
| GSTT3LA55005 | - | 40-16 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 1.7 | 0.8 | 55° | ● | ● | |
| GSTT3LB55005 | - | 40-16 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 0.8 | 1.7 | 55° | ● | ● | |
| GSTT3RA6000 | 0.2-0.6 | 64-48 | 3 | 2.5 | 8.7 | 5.2 | - | 0.4 | 2.1 | 60° | ● | ● | |
| GSTT3RB6000 | 0.2-0.6 | 64-48 | 3 | 2.5 | 8.7 | 5.2 | - | 2.1 | 0.8 | 60° | ● | ● | |
| GSTT3RA60005 | 0.5-1.25 | 48-24 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 0.8 | 1.7 | 60° | ● | ● | |
| GSTT3RB60005 | 0.5-1.25 | 48-24 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 1.7 | 0.8 | 60° | ● | ● | |
| GSTT3RN6001 | 1-1.5 | 24-18 | 3 | 2.5 | 8.7 | 5.2 | 0.1 | 1.25 | 1.25 | 60° | ● | ● | |
| GSTT3RA55005 | - | 40-16 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 0.8 | 1.7 | 55° | ● | ● | |
| GSTT3RB55005 | - | 40-16 | 3 | 2.5 | 8.7 | 5.2 | 0.05 | 1.7 | 0.8 | 55° | ● | ● | |
●StockOAvailable Upon Order
Thread Turning Tool Holders
External Diameter Tool Holder
The diagram shows the right hand
| Order No. | Dimensions (mm) | Suitable | Screw | Shim | Shim Screw | Wrench | ShimWrench | InStock | ||||||
| H=HF | B | LF | WF | LH | Insert |  |  |  |  |  | R | L | ||
| SER/L1212F11 | 12 | 12 80 14 16 11ER/L... SI60M025080-03510H | 1 | 1 | TT08PH | 1 | 0.09 | |||||||
| SER/L1212F16 | 12 | 12 | 80 | 16 | 21 | SI60M035090-05312H | 一 | 1 | TT15PH | 1 | 0.09 | ● | ||
| SER1212H16 | 12 | 12 | 100 | 16 | 21 | SI60M035090-05312H | 一 | 1 | TT15PH | 1 | 0.09 | O | ||
| SER/L1616H16 | 16 | 16 | 100 | 20 | 24 | SI60M035120-05316H | DEN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.20 | ● | ● | |
| SER/L2020K16 | 20 | 20 | 125 | 25 | 27 | 16ER/L... | SI60M035120-05316H | DEN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.39 | ● | |
| SER/L2525M16 | 25 | 25 | 150 | 32 | 32 | SI60M035120-05316H | DEN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.74 | ● | ● | |
| SER3225P16 | 32 | 25 | 170 | 40 | 30 | SI60M035120-05316H | DEN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.96 | O | ||
| SER/L3232P16 | 32 | 32 | 170 | 40 | 31 | SI60M035120-05316H | DEN16P15SH | SSBM030060H | TT15PH | TH25LH | 1.37 | ● | O | |
| SER/L2525M22 | 25 | 25 | 150 | 32 | 31 | SI60M040160-07013H | DEN22P15SH | SSBM040060H | TT20PH | TH30LH | 0.74 | ● | O | |
| SER3225P22 | 32 | 25 | 170 | 40 | 32 | SI60M040160-07013H | DEN22P15SH | SSBM040060H | TT20PH | TH30LH | 0.96 | O | ||
| SER/L3232P22 | 32 | 32 | 170 | 40 | 32 | SI60M040160-07013H | DEN22P15SH | SSBM040060H | TT20PH | TH30LH | 1.37 | O | ||
| SER/L4040R22 | 40 | 40 | 200 | 50 | 32 | SI60M040160-07013H | DEN22P15SH | SSBM040060H | TT20PH | TH30LH | 2.51 | O | O | |
| SER2525M27 | 25 | 25 | 15032 | 25 | SI60M050160-07212H | DEN27P15SH | SSBM040060H | TT20PH | TH30LH | 0.74 | O | |||
| SER/L3232P27 | 32 | 32 | 17040 | 33 | 27ER/L... | SI60M050160-07212H | DEN27P15SH | SSBM040060H | TT20PH | TH30LH | 1.37 | ● | ● | |
| SER/L4040R27 | 40 | 4020050 33 | SI60M050160-07212HDEN27P15SH | SSBM040060HTT20PHTH30LH 2.51 O | ||||||||||
Notes: SI60M025080\* represents M3.5\*12
●StockOAvailable Upon Order
●StockOAvailable Upon Order
Thread Turning Tool Holders
Tool Holder with Internal Hole
The diagram shows the right hand
| Order No. | Dimensions (mm) | Suitable | Screw | Shim | Shim Screw | Wrench | ShimWrench | InStock | |||||||
| DMIN | DCONMS | H | LF | WF | LH | Insert | mom | P | RL | ||||||
| SIR/L0008K08 | 9.9 | 8 7.41254.952008IR/L... | SI60M022050-03008H | 1 | 1 | TT06PH | 1 | 0.05 | ●● | ||||||
| SIR/L0010K11 | 13 | 10 | 9 | 125 | 6.5 | 25 | SI60M025060-03510H | 1 | 1 | TT08PH | 1 | 0.08 | ● | ||
| SIR0010H11 | 13 | 10 | 9 | 100 | 6.5 | 25 | SI60M025060-03510H | 1 | 一 | TT08PH | 1 | 0.08 | O | ||
| SIR/L0010K11-A16 | 13 | 16 | 15 | 125 | 6.5 | 30 | 11IR/L... | SI60M025060-03510H | 1 | 1 | TT08PH | 1 | 0.20 | O | |
| SIR/L0012K11 | 15 | 12 | 11 | 125 | 7.4 | 28 | SI60M025060-03510H | 1 | 1 | TT08PH | 1 | 0.11 | O | ||
| SIR/L0012K11-A16 | 15 | 16 | 15 | 125 | 7.4 | 36 | SI60M025060-03510H | 1 | 1 | TT08PH | 1 | 0.20 | O | ||
| SIR/L0013M16 | 19 | 16 | 15 | 150 | 9.4 | 32 | SI60M035090-05312H | 1 | 1 | TT15PH | 1 | 0.24 | O | ||
| SIR/L0016Q16 | 21 | 16 | 15 | 180 | 10.8 | 40 | SI60M035090-05312H | 1 | 1 | TT15PH | 1 | 0.28 | ● | ||
| SIR0016N16 | 21 | 16 | 15 | 160 | 10.8 | 40 | SI60M035090-05312H | 1 | 1 | TT15PH | 1 | 0.28 | O | ||
| SIR/L0020Q16 | 24 | 20 | 18 | 180 | 13.1 | 40 | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.44 | |||
| SIR0020P16 | 24 | 20 | 18 | 170 | 13.1 | 40 | 16IR/L... | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.44 | O | |
| SIR/L0025R16 | 29 | 25 | 23 | 200 | 15.6 | 45 | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 0.77 | O | ||
| SIR/L0032S16 | 38 | 32 | 30 | 250 | 19.1 | 50 | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 1.58 | O | ||
| SIR/L0040T16 | 44 | 40 | 38 | 300 | 23.1 | 55 | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 2.96 | C | ||
| SIR/L0050U16 | 60 | 50 | 48 | 350 | 28.1 | 50 | SI60M035120-05316H | DIN16P15SH | SSBM030060H | TT15PH | TH25LH | 5.39 | OO | ||
| SIR/L0020Q22 | 26 | 20 | 18 | 180 | 13.2 | 40 | SI60M040120-07010H | 1 | 一 | TT20PH | 1 | 0.44 | |||
| SIR/L0025R22 | 32 | 25 | 23 | 200 | 16.4 | 46 | SI60M040160-07013H | DIN22P15SH | SSBM040060H | TT20PH | TH30LH | 0.77 | |||
| SIR/L0032S22 | 39 | 32 | 30 | 250 | 19.9 | 50 | 22IR/L... | SI60M040160-07013H | DIN22P15SH | SSBM040060H | TT20PH | TH30LH | 1.58 | O | |
| SIR/L0040T22 | 47 | 40 | 38 | 300 | 23.9 | 55 | SI60M040160-07013H | DIN22P15SH | SSBM040060H | TT20PH | TH30LH | 2.96 | OO | ||
| SIR/L0050U22 | 57 | 50 | 48 | 350 | 28.9 | 70 | SI60M040160-07013H | DIN22P15SH | SSBM040060H | TT20PH | TH30LH | 5.39 | O | ||
| SIR/L0032S27 | 42 | 32 | 30 | 250 | 20.9 | 50 | SI60M050160-07212H | DIN27P15SH | SSBM040060H | TT20PH | TH30LH | 1.58 | OO | ||
| SIR/L0040T27 | 50 | 40 | 38 | 300 | 25 | 55 | 27IR/L... | SI60M050160-07212H | DIN27P15SH | SSBM040060HTT20PH | TH30LH | 2.96 | O | ||
| SIR/L0050U27 | 60 | 50 | 48 | 350 | 30.170 | SI60M050160-07212H | DIN27P15SH | SSBM040060H | TT20PH | TH30LH | 5.39 | OO | |||
Notes: SI60M025080\* represents M3.5\*12
●Stock OAvailable Upon Order
●Stock OAvailable Upon Order
