2025年Gesac车刀目录 - 电子画册在线预览、各类电子画册在线制作-云展网平台

Turning Insert (Negative)

Triangle 60° with Hole

Ordering Code		Dimension (mm)				Coated Carbides Cermet		Car- bides
		LE	IC	S	D1 RE	GP110 GP620 GP1130 GM215 GM20 GMM25 GP105 GPP135 G115 GM25 GM230 GP225 GP130 GP115 GP120		GST115 GST120 GST130 GN20 GK125 GS1115 G91110 GN9120 GK15 GK120
	TNMG160404-LM	16.5	9.525	4.76	3.81 0.4		GN130 GP1TM GP1TM
	TNMG160408-LM		16.5	9.525 4.76	3.81	0.8
	TNMG160412-LM	16.5	9.525	4.76	3.81 1.2			●
		TNMG160408-EM	16.5		3.81
	TNMG160412-EM	16.5	9.525 9.525	4.76 4.76	0.8 3.81 1.2


	TNMX160408- WMV	16.5	9.525	4.76	3.81 0.8		O
	TNMX160412- WMV	16.5	9.525	4.76	3.81 1.2		O


	TNMG160404-MK	16.5	9.525	4.76	3.81 0.4
	TNMG160408-MK	16.5	9.525	4.76	3.81 0.8
	TNMG160412-MK	16.5	9.525	4.76 3.81	1.2

	TNMG160404-UK 16.5		9.525	4.76 3.81	0.4
	TNMG160408-UK TNMG160412-UK	16.5	9.525	4.76 3.81	0.8
	TNMG160416-UK	16.5	9.525	4.76 3.81	1.2 1.6		O
		16.5	9.525 4.76	3.81			O
TNMG220408-UK TNMG220412-UK		22 22	12.7	4.76 5.16	0.8		O
	TNMG220416-UK		12.7	4.76 5.16	1.2
	TNMG160408-LR	22	12.7	4.76 5.16	1.6	O	●
		16.5	9.525	4.76 3.81	0.8
	TNMG160412-LR TNMG220408-LR 22	16.5 9.525	4.76 12.7 4.76	3.81 1.2 5.16 0.8

	TNMG160408-QR	16.5
	TNMG160412-QR	16.5	9.525 9.525	4.76	3.81 0.8 3.81 1.2 O	O O O
	TNMG220408-QR	22	12.7	4.76 4.76	5.16 0.8 O
	TNMG220412-QR	22	12.7		5.16 1.2
				4.76	O
	TNMG220416-QR	22	12.7	4.76	5.16 1.6 O	○O
	TNMG270608-QR	27.5	15.875	6.35 6.35	0.8	O
	TNMG270612-QR	27.5	15.875	6.35	6.35 1.2 O
	TNMG270616-QR	27.5	15.875	6.35 6.35	1.6
TNMG330924-QR		33 19.05	9.52	7.94	2.4 O

●StockOAvailable Upon Order

Turning Insert (Negative)

Triangle 60° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																Car-bides	Cermet
Ordering Code		LE	IC	S	D1	RE	GP110	GP20GP130GP105	GP115GP120GP225	GP130GP	135	G115GM	125GM	230GM	215GM	220	GM25GK115		GK120	GK125GS15GST	120GST130	GNT20GS115G	1110GN9120GN91130G	P1TMGP11TM	GPTM
	TNMG160408-HK 16.5 9.5254.763.810.8
	TNMG160412-HK	16.5	9.525	4.76	3.81	1.2												●	●	●
	TNMG220408-HK	22	12.7	4.76	5.160.8												●		●	●
	TNMG220412-HK	22	12.7	4.76	5.16	1.2												●		O
	TNMG220416-HK	22	12.7	4.76	5.16	1.6											●〇			●
	TNMG270612-HK	27.5	15.875	6.35	6.35	1.2												●		●
	TNMG270616-HK	27.5	15.875	6.35	6.35	1.6											●			●
	TNMA110304	11	6.35	3.18	2.26	0.4														O
	TNMA160308	16.5	9.525	3.18	3.810.8												●			●
	TNMA160404	16.5	9.525	4.76	3.81	0.4											●			●
	TNMA160408	16.5	9.525	4.76	3.810.8
	TNMA160412	16.5	9.525	4.76	3.81	1.2											o			●
	TNMA160416	16.5	9.525	4.76	3.811.6												O
	TNMA220404	22	12.7	4.76	5.160.4															●
	TNMA220408	22	12.7	4.765.160.8													O O
	TNMA220412	22	12.7	4.76	5.161.2												O O
	TNMA220416	22 12.7 4.765.161.6 O

Stock OAvailable Upon Order

Turning Insert (Negative)

Rhombic 35° with Hole

Ordering Code		Dimension(mm)					Coated Carbides								Car-bides	Cermet
		GP110GP120GP130 G115GM125GM230GM215GM20GM25 GSTT115GST20GST130 GN20GP105GP115GP120GP225GP130GP135GK115GK120GK125GS15G91110GN91120GN930GP1TMGP1TMGPZTMRE16.6 9.5254.763.810.2 O

		VNMG160404-QF	16.6	9.525	4.76	3.81	0.2					O				O
		VNMG160408-QF	16.6	9.525	4.76	3.81	0.2 O
V		VNMG220408-QF			22.1	12.7		4.76	5.16	0.8	O
		VNMG160404-TF	16.6	9.525	4.76	3.81	0.4										O
		VNMG160408-TF	16.6	9.525	4.76	3.81	0.8										O


		VNMG160404-GF	16.6	9.525	4.763.81		0.4 O
		VNMG160408-GF	16.6	9.525	4.76	3.81	0.8
		VNMG220404-GF	22.1	12.7	4.76	5.16	0.4 O

		VNMG160404-SF	16.6	9.525	4.76	3.81	0.4				●●			●
		VNMG160408-SF	16.6	9.525	4.76	3.81	0.8


	R	VNMG160404-YF	16.6	9.525	4.76	3.81	0.4
		VNMG160408-YF	16.6	9.525	4.76	3.81	0.8


	R	VNMG160404-SPL	16.6	9.525	4.76	3.81	0.4
		VNMG160408-SPL	16.6	9.525	4.76	3.81	0.8


		VNMG160404-EL	16.6	9.525	4.76	3.81	0.4
		VNMG160408-EL	16.6	9.525	4.76	3.81	0.8						●
		VNMG160412-EL	16.6	9.525	4.76	3.81	1.2

	VNMG160404-SML	16.6	9.525	4.76	3.81	0.4
	NMG160408-SML	16.6	9.525	4.76	3.81	0.8
	VNMG160412-SML	16.6	9.525	4.76	3.81	1.2

		VNMG160404-QM	16.6	9.525	4.76	3.81	0.4C C
		VNMG160408-QM	16.6	9.525	4.76	3.81	0.8										O
	VNMG160412-QM	16.6	9.525	4.76	3.81	1.2 C

Stock OAvailable Upon Order

Turning Insert (Negative)

Rhombic 35° with Hole

Ordering Code	Dimension(mm)					Coated Carbides						Car-bides
	LE	IC	S	D1	RE	GP110GP1120GP130 G15GM125GM230GM215GM20GM25 GS15GST20GST130 GN20GP105GP115GP120GP225GP130GP135GK115GK120GK125GS115G9110GN9120GN9130GP1TMGP1TMGPTM
	16.6 9.5254.763.810.4 O
	VNMG160408-GM	16.6	9.525	4.763.810.8
	VNMG160412-GM	16.6	9.5254.763.811.2

	R	VNMG160404-SM	16.6	9.525	4.763.81		0.4	O O
		VNMG160408-SM	16.6	9.525	4.76	3.81	0.8	O○O	O


		VNMG160404-TP	16.6	9.525	4.76	3.81	0.4						●
		VNMG160408-TP	16.6	9.525	4.76	3.81	0.8


		VNMG160404-LM	16.6	9.525	4.76	3.81	0.4	●	C
		VNMG160408-LM	16.6	9.525	4.76	3.81	0.8


		VNMG160408-EM	16.6	9.525	4.76	3.81	0.8
		VNMG160412-EM	16.6	9.525	4.76	3.81	1.2				●


		MMG160408-	16.6	9.525	4.76	3.81	0.8
		NMG160412-	16.6	9.525	4.76	3.81	1.2


		VNMG160404-MK	16.6	9.525	4.76	3.81	0.4
		VNMG160408-MK	16.6	9.525	4.76	3.81	0.8
		VNMG160412-MK	16.6	9.525	4.76	3.811.2

		VNMG160404-UK	16.6	9.525	4.763.81		0.4
		VNMG160408-UK	16.6	9.525	4.76	3.810.8
		VNMG160412-UK	16.6	9.525	4.76	3.811.2

		VNMG160408-HK	16.6	9.525	4.76	3.810.8				O
		VNMG160412-HK	16.6	9.525	4.76	3.811.2

Turning Insert (Negative)

WNI

Trigon 80° with Hole

Ordering Code		Dimension(mm)					Coated Carbides							Car-Cermetbides
		LE	IC	S	D1	RE	GP110GP20GP130 G115GM125GM230GM215GM220GM25 GST115GST20GST130 GN20GP105GP115GP120GP225GP130GPP135GK15GK120GK125GS1115G91110GN91120GN9130GP1TMGP1TMGPTM
	WNMG060404-QF 6.5 9.5254.763.810.4 O
	WNMG060408-QF	6.5	9.525	4.76	3.81	0.8	●●		O
	WNMG080404-QF	8.7	12.7	4.76	5.16	0.4	O C								●O
	WNMG080408-QF	8.7	12.7	4.76	5.16	0.8
	WNMG080404-TF	8.7	12.7	4.76	5.16	0.4									O
	WNMG080408-TF	8.7	12.7	4.76	5.16	0.8										O


2	WNMG06T304-GF	6.5	9.525	3.97	3.810.4 O
	WNMG06T308-GF	6.5	9.525	3.97	3.81	0.8			O
	WNMG060404-GF	6.5	9.525	4.76	3.81	0.4			O
	WNMG060408-GF	6.5	9.525	4.76	3.81	0.8			O
	WNMG080404-GF	8.7	12.7	4.76	5.16	0.4		O
	WNMG080408-GF	8.7	12.7	4.76	5.16	0.8
	WNMG060404-SF	6.5	9.525	4.76	3.81	0.4				O			●
	WNMG060408-SF	6.5	9.525	4.76	3.81	0.8				O			●
	WNMG080404-SF	8.7	12.7	4.76	5.16	0.4				O			●
	WNMG080408-SF	8.7	12.7	4.76	5.16	0.8				●			●
	WNMG080404-YF	8.7	12.7	4.76	5.16	0.4				●
	WNMG080408-YF	8.7	12.7	4.76	5.16	0.8


	WNMG080404-SPL	8.7	12.7	4.76	5.160.4
2	WNMG080408-SPL	8.7	12.7	4.76	5.16	0.8


	WNMG080404-EL	8.7	12.7	4.76	5.160.4						O
	WNMG080408-EL	8.7	12.7	4.76	5.160.8							●
	WNMG080412-EL	8.7	12.7	4.76	5.161.2							●●

	WNMG080404-SML	8.7	12.7	4.765.160.4
	WNMG080408-SML	8.7	12.7	4.76	5.16	0.8
	WNMG080412-SML	8.7	12.7	4.765.161.2 ●○

StockOAvailable Upon Order

Turning Insert (Negative)

Trigon 80° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																					Car-bides		Cermet
Ordering Code		LE	IC	S	D1	RE	GP110GP	120GP	130GP	105GP	115	GP120	GP225	GP130GP	135	G115	GM25	GMM230	GM2215	GM20	GM25	GK115GK	120GK	125	GST115GST120	GST130	GS115GN20	G1110	GN91120GN91130	GP11TM	GP11TMGPTM
	WNMG060404-QM	6.5	9.5254.76		3.810.4 O							●			●						●
	WNMG060408-QM	6.5	9.525	4.76	3.81	0.8					●		●
	WNMG060412-QM	6.5	9.525	4.76	3.81	1.2	o			O
	WNMG080404-QM	8.7	12.7	4.76	5.16	0.4					●		●				O
	WNMG080408-QM	8.7	12.7	4.76	5.16	0.8		0							●																●
	WNMG080412-QM	8.7	12.7	4.76	5.16	1.2		●				●
	WNMG080416-QM	8.7	12.7	4.76	5.16	1.6			●●				●		●
	WNMG06T304-GM	6.5	9.525	3.97	3.81	0.4				O			●
	WNMG06T308-GM	6.5	9.525	3.97	3.81	0.8	O					●
	WNMG06T312-GM	6.5	9.525	3.97	3.81	1.2				O			●									O
	WNMG060404-GM	6.5	9.525	4.76	3.81	0.4			O			●
	WNMG060408-GM	6.5	9.525	4.76	3.81	0.8				O
	WNMG080404-GM	8.7	12.7	4.76	5.16	0.4						●
	WNMG080408-GM	8.7	12.7	4.76	5.16	0.8						●									●
	WNMG080412-GM	8.7	12.7	4.76	5.16	1.2
	WNMG080416-GM	8.7	12.7	4.76	5.16	1.6				●		●
	WNMG080408R-SV	8.7	12.7	4.76	5.16	0.8			●			●
	WNMG080408L-SV	8.7	12.7	4.76	5.16	0.8			●			●

Stock OAvailable Upon Order

Turning Insert (Negative)

WNI

Trigon 80° with Hole

Ordering Code			Dimension (mm)			Coated Carbides			Car- bides	Cermet
Ordering Code			LE	IC	S	D1 RE	GP110 GP120 GP630 GP105 GP135 GP115 GP120 GP2225 GP30	GMM215 GM20 GM25 GS115 G115 GM125 GM230 GK125 GK15 GK20	GST120 GS130 GNT20 GS15	G110 GN9120	GN930 GP1TM
	WNMG06T304-SM	6.5	9.525	3.97	3.81	0.4					GPTM GPPZTM
	WNMG06T308-SM	6.5	9.525	3.97	3.81 0.8
	WNMG060404-SM	6.5	9.525	4.76	3.81 0.4		O O O
	WNMG060408-SM	6.5	9.525	4.76	3.81	0.8
	WNMG060412-SM	6.5	9.525	4.76	3.81	1.2	O
	WNMG080404-SM	8.7	12.7	4.76	5.16	0.4
	WNMG080408-SM	8.7	12.7	4.76	5.16 0.8					O
	WNMG080412-SM	8.7	12.7	4.76	5.16	1.2	C
	WNMG080404-TP	8.7	12.7	4.76	5.16	0.4
	WNMG080408-TP	8.7	12.7	4.76	5.16	0.8


	WNMG06T304-LM	6.5	9.525	3.97	3.81	0.4		O
	WNMG06T308-LM	6.5	9.525	3.97	3.81 0.8			O
	WNMG060404-LM	6.5	9.525	4.76	3.81 0.4		O O
	WNMG060408-LM	6.5	9.525	4.76	3.81	0.8
	WNMG080404-LM	8.7	12.7	4.76	5.16 0.4 0.8
	WNMG080408-LM	8.7	12.7	4.76	5.16		O O
	WNMG080412-LM	8.7 8.7	12.7	4.76	5.16 1.2			C
	WNMG080408-EM	8.7	12.7 12.7	4.76 4.76	5.16 0.8 5.16 0.8
WNMG080412-EM

	WNMG080408- SMM	8.7	12.7	4.76	5.16	0.8
	WNMG080412- SMM	8.7	12.7	4.76	5.16 1.2


	WNMG080408- WMV	8.7	12.7	4.76	5.16	0.8			O
	WNMG080412- WMV	8.7	12.7	4.76	5.161.2			● O


	WNMG080404-MK	8.7	12.7	4.76	5.16 0.4
	WNMG080408-MK	8.7	12.7	4.76	5.16	0.8
	WNMG080412-MK	8.7	12.7	4.76	5.16 1.2

Stock OAvailable Upon Order

Turning Insert (Negative)

Trigon 80° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																				Car-bides			Cermet
Ordering Code		LE	IC	S	D1	GPRE	110GP	20GP130GP		105GP	115GP	120	GP25	GP130	GP135G	115	GM125GMM	230	GM215GM	220GM	225	GK15	GK120GK	125GS15GST	120GST130GS	115GNT120	G9110G	91120	GN130GP	1TM	GP11TM	GPTM
	WNMG080404-UK 8.7 12.7 4.765.160.4																				●		●●
	WNMG080408-UK	8.7	12.7	4.76	5.16	0.8																●	●	●
	WNMG080412-UK	8.7	12.7	4.765.161.2																	●		●●

	WNMG080408-LR	8.7	12.7	4.76	5.16	0.8									●					●	●
	WNMG080412-LR	8.7	12.7	4.76	5.16	1.2										●		O		●	●


	WNMG080408-QR	8.7	12.7	4.765.160.8			●	●●○			●		●		●
	WNMG080412-QR	8.7	12.7	4.76	5.16	1.2	●	●	●	●	●		●		●
	WNMG080416-QR	8.7	12.7	4.765.161.6									O		●

	WNMG06T308-HK	6.5	9.525	3.97	3.810.8																	●	●
	WNMG060408-HK	6.5	9.525	4.76	3.81	0.8																●		●
	WNMG080408-HK	8.7	12.7	4.76	5.160.8																	●	●●
	WNMG080412-HK	8.7	12.7	4.76	5.16	1.2
	WNMA06T304	6.5	9.525	3.97	3.810.4
	WNMA060404	6.5	9.525	4.76	3.81	0.4															●
	WNMA060408	6.5	9.525	4.76	3.810.8
	WNMA080404	8.7	12.7	4.76	5.160.4																		。
	WNMA080408	8.7	12.7	4.765.160.8																	●
	WNMA080412	8.7	12.7	4.765.161.2																	●
	WNMA080416	8.7	12.7	4.765.161.6																	O

●Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 80° with Hole

Ordering Code		Dimension(mm)				Car-Coated Carbides Cermetbides
Ordering Code		LE	IC	S	D1	GP110GP6120GP130GP105 G115GM125G230GM215G20GMM25 GK125GS115GS20GST130GS1115GN20GP115GP120GP25GP130GP135GK15GK120G9110GN9120GN1130GP1TMGP11TMGPTMRE
	CCMT060202-MM 6.5 6.352.38 2.8 0.2C ● C O
	CCMT060204-MM	6.5	6.35	2.38 2.8		0.4 O
	CCMT060208-MM	6.5	6.35	2.38 2.8		0.8 O O
	CCMT09T302-MM	9.7	9.525	3.97	4.4	0.2 O
	CCMT09T304-MM	9.7	9.525	3.97	4.4	0.4
	CCMT09T308-MM	9.7	9.525	3.97	4.4	0.8 C
	CCMT120404-MM	12.9	12.7	4.76	5.56	0.4
	CCMT120408-MM	12.9	12.7	4.76	5.56	0.8
	CCMT060204-FP	6.5	6.35	2.38	2.8	0.4 0
	CCMT09T302-FP	9.7	9.525	3.97	4.4	0.200
	CCMT09T304-FP	9.7	9.525	3.97	4.4	0.40 0 0 O0
	CCMT09T308-FP	9.7	9.525	3.97	4.4	0.8 0 0 0
	CCMT060202-SPL	6.5	6.35	2.38	2.8	0.2
	CCMT060204-SPL	6.5	6.35	2.38	2.8	0.4
	CCMT09T302-SPL	9.7	9.525	3.97	4.4	0.2
	CCMT09T304-SPL	9.7	9.525	3.97	4.4	0.4
	CCMT09T308-SPL	9.7	9.525	3.97 4.4		0.8
	CCMT060202-GP	6.5	6.35	2.38 2.8		0.2C O O OO
	CCMT060204-GP	6.5	6.35	2.38 2.8 0.4C OO
	CCMT060208-GP	6.5	6.35	2.38	2.8	0.8 O OO OO
	CCMT09T302-GP	9.7	9.525	3.97	4.4	0.2 O ○○
	CCMT09T304-GP	9.7	9.525	3.97	4.4	0.4
	CCMT09T308-GP	9.7	9.525	3.97 4.4		0.8 O●
	CCMT120404-GP	12.9	12.7	4.765.56		0.4 O OO
	CCMT120408-GP	12.9	12.7	4.765.56		0.8 O●
	CCMT120412-GP	12.9	12.7	4.765.561.2 O O
	CCGT060202-GP	6.5	6.35	2.38 2.80.2
	CCGT060204-GP	6.5	6.35	2.38 2.80.4
	CCGT060208-GP	6.5	6.35	2.38 2.8 0.8
	CCGT09T302-GP	9.7	9.525	3.97 4.40.2
	CCGT09T304-GP	9.7	9.525	3.97 4.4 0.4
	CCGT09T308-GP	9.7	9.525	3.97 4.4 0.8
	CCGT120404-GP	12.9	12.7	4.765.560.4
	CCGT120408-GP	12.9	12.7	4.765.560.8 O

Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 80° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																			Car-bides			Cermet
Ordering Code		LE	IC	S	D1	GPRE	110GP6120GP130GP	105	GP115GP	120	GP225GP	130	GP135	G115GM	125GM	230GM	215GM	220	GM25	GK15GK	120	GK125GST115	GST120GST130	GS115	GNT20	G9110	G9120	GN91130	GP1TMGP11TMGPTM
	CCMT060202-TP	6.5	6.352.382.80.2																										●●
	CCMT060204-TP	6.5	6.35	2.38	2.8	0.4																							●	●
	CCMT060208-TP	6.5	6.35	2.38	2.8	0.8																							●	●
	CCMT09T302-TP	9.7	9.525	3.97	4.4	0.2																							●	●
	CCMT09T304-TP	9.7	9.525	3.97	4.4	0.4																							●	●
	CCMT09T308-TP	9.7	9.525	3.97	4.4	0.8																							●	●
	CCMT120404-TP	12.9	12.7	4.76	5.56	0.4																							●	●
	CCMT120408-TP	12.9	12.7	4.76	5.56	0.8																							●	●
	CCMT060204-KM	6.5	6.35	2.38	2.8	0.4														●●		●
	CCMT09T304-KM	9.7	9.525	3.97	4.4	0.4															●	●
	CCMT09T308-KM	9.7	9.525	3.97	4.4	0.8													●
	CCMT120404-KM	12.9	12.7	4.76	5.56	0.4														●
	CCMT120408-KM	12.9	12.7	4.76	5.56	0.8													●●
	CCMT120412-KM	12.9	12.7	4.76	5.56	1.2														●	●●
	CCGX060202-AL	6.5	6.35	2.38	2.8	0.2																		●		●
	CCGX060204-AL	6.5	6.35	2.38	2.8	0.4																		●		O
	CCGX060208-AL	6.5	6.35	2.38	2.8	0.8
	CCGX09T302-AL	9.7	9.525	3.97	4.4	0.2																		●
	CCGX09T304-AL	9.7	9.525	3.97	4.40.4																			●●
	CCGX09T308-AL	9.7	9.525	3.97	4.4	0.8
	CCGX120402-AL	12.9	12.7	4.76	5.50.2																			●●
	CCGX120404-AL	12.9	12.7	4.76	5.50.4																			O
	CCGX120408-AL	12.9	12.7	4.76	5.50.8

●Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 80° with Hole

Ordering Code

Dimension(mm)

Coated Carbides

Car-bides

Cermet

GP110

GP620GP130

GP105GP

115GP120

GP225

GP130

GP135

G115

GM1125

GM230

GM215

GM220GM25

GK15

GK120

GK125GS15

GST120GST130

GN20GS115

G91110GN

91120

GN9130

GP1TM

GP1TMGPTM

CPGT060204-GP

6.5 6.352.382.80.4

CPGT060208-GP

6.5

6.35

2.38

2.8

0.8

CPGT09T302-GP

9.7

9.525

3.97

4.40.2

●

CPGT09T304-GP

9.7

9.525

3.97

4.4

0.4

●

CPGT09T308-GP

9.7

9.525

3.97

4.40.8

CPGT120404-GP

12.9

12.7

4.76

5.56

0.4

CPGT120408-GP

12.9

12.7

4.765.560.8

Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 55° with Hole

Ordering Code			Dimension(mm)					Car-Coated Carbides Cermetbides
			LE	IC	S	D1	RE	GP110GP120GP130GP105 GP225 GP135G115G125GM230GM215GM220GM225 GK125GST15GST20GST130GS115GNT20GP115GP120GP30GK15GK120G9110GN91120GN9130GP1TMGP1TMGPTM
D	DCMT070202-MM		7.8 6.35 2.38 2.8 0.2
	DCMT070204-MM		7.8	6.35	2.38	2.8	0.4
	CMT070208-MM		7.8	6.35	2.38	2.8	0.8
	DCMT11T302-MM		11.6	9.525	3.97	4.4	0.2

		DCMT11T304-MM	11.6	9.525	3.97	4.4	0.4
	DCMT11T308-MM		11.6	9.525	3.97	4.4	0.8
	DCMT070208-FP		7.8	6.35	2.38	2.80.8 0
	DCMT11T304-FP		11.6	9.525	3.97	4.4	0.400		0
		DCMT11T308-FP		11.6	9.525	3.97	4.4 0.80 0 0 0 0 0

	DCMT070204-SPL		7.8	6.35	2.38	2.80.4
	DCMT11T302-SPL		11.6	9.525	3.97	4.4	0.2
	DCMT11T304-SPL		11.6	9.525	3.97	4.40.4
	DCMT11T308-SPL		11.6	9.525	3.97	4.40.8
	DCMT070202-GP		7.8	6.35	2.38	2.80.2 O O			O OO
	DCMT070204-GP		7.8	6.35	2.38	2.80.4			O O
	DCMT070208-GP		7.8	6.35	2.38	2.8 0.8			O
	DCMT11T302-GP		11.6	9.525	3.97	4.40.2
	DCMT11T304-GP		11.6	9.525	3.97	4.40.4
	DCMT11T308-GP		11.6	9.525	3.97	4.40.8			O
	DCMT11T312-GP		11.6	9.525	3.97	4.41.2
	DCMT150404-GP		15.5	12.7	4.76	5.560.4 O O			O
	DCMT150408-GP		15.5	12.7	4.76	5.560.8O O ● O O
	DCMT150412-GP		15.5	12.7	4.76	5.561.2			O
	DCGT070202-GP		7.8	6.35	2.38	2.80.2
	DCGT070204-GP		7.8	6.35	2.38	2.80.4
	DCGT070208-GP		7.8	6.35	2.38	2.80.8 O
	DCGT11T302-GP		11.6	9.525	3.97	4.40.2
	DCGT11T304-GP		11.6	9.5253.97		4.40.4
	DCGT11T308-GP		11.6	9.5253.97		4.40.8

●Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 55° with Hole

Ordering Code		Dimension(mm)					Coated Carbides											Car-bides	Cermet
Ordering Code		LE	IC	S	D1	GPRE	110GP120	GP130GP	105GP115GP	120GP25GP130GPP135G115GM	125GMM	230	GM215	GM220GM25GK115GK120GK	125GS115GST120GST130GS115		GN20	G9110GN91120GN91130	GP1TMGP11TMGPTM
	DCMT070202-TP	7.8 6.35 2.38 2.80.2																	●●
	DCMT070204-TP	7.8	6.35	2.38	2.8	0.4													●	●
	DCMT070208-TP	7.8	6.35	2.38	2.8	0.8														●
	DCMT11T302-TP	11.6	9.525	3.97	4.4	0.2													●	●
	DCMT11T304-TP	11.6	9.525	3.97	4.4	0.4													●	●
	DCMT11T308-TP	11.6	9.525	3.97	4.4	0.8													●	●
	DCMT11T304-KM	11.6	9.525	3.97	4.4	0.4									●
	DCMT11T308-KM	11.6	9.525	3.97	4.4	0.8									●


	DCGX070202-AL	7.8	6.35	2.38	2.80.2											O
	DCGX070204-AL	7.8	6.35	2.38	2.8	0.4										●
	DCGX070208-AL	7.8	6.35	2.38	2.80.8											O
	DCGX11T302-AL	11.6	9.525	3.97	4.4	0.2
	DCGX11T304-AL	11.6	9.525	3.97	4.40.4
	DCGX11T308-AL	11.6	9.525	3.97	4.4	0.8

StockOAvailable Upon Order

Turning Insert (Positive)

Square 90° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																				Car-bides			Cermet
Ordering Code		LE	IC	S	D1	GPRE	110GP6120GP		130	GP105	GP115	GP120GP225GP130		GP135	G115	GM1125	GMM230	GM215	GM20	GMM25	GK15	GK120	GK125GST115GST	120GST130	GS15	GN20G	91110	GN1120	GN91130	GP1TM	GP1TM	GPTM
	SCMT09T304-MM 9.5259.5253.97 4.4 0.4 O
	SCMT09T308-MM	9.525	9.525	3.97	4.4	0.8			●										●	●	●	●								O

_
	SCMT09T304-GP	9.525	9.525	3.97	4.4	0.4			O		●		●		●	●	●	●〇			●	○●								○○
	SCMT09T308-GP	9.525	9.525	3.97	4.4	0.8	●	●			●	●	●			●	●		●		●		●
	SCMT120404-GP	12.7	12.7	4.76	5.56	0.4			O		●		●			O	O	●			●		O							O
	SCMT120408-GP	12.7	12.7	4.76	5.56	0.8	●	●	●		●	●	●		●	●	●		●		●	●	O								O
	SCMT09T304-TP	9.525	9.525	3.97	4.4	0.4																									●
	SCMT09T308-TP	9.525	9.525	3.97	4.4	0.8																									●
	SCMT120404-TP	12.7	12.7	4.76	5.56	0.4																									●
	SCMT120408-TP	12.7	12.7	4.76	5.56	0.8																									●
	SCMT09T308-KM	9.525	9.525	3.97	4.4	0.8														●		●●
	SCMT120408-KM	12.7	12.7	4.76	5.56	0.8															●	●	●
	SCMT120412-KM	12.7	12.7	4.76	5.56	1.2															●●

		SCGX09T304-AL			9.525	9.525		3.97		4.4		0.4																			○○
		SCGX09T308-AL	9.525	9.525	3.97	4.4	0.8																			●			●
		SCGX120404-AL	12.7	12.7	4.76	5.5	0.4																			O
	SCGX120408-AL	12.7	12.7	4.76	5.5	0.8																			○○

●Stock OAvailable Upon Order

Turning Insert (Positive)

Triangle 60° with Hole

Ordering Code		Dimension(mm)					Coated Carbides								Car-Cermetbides
		LE	IC	S	D1	GP110GP20GP130 G115GM125GMM230GM215GM20GM25 GS15GST120GST130 GN20GP105GP115GP120GP25GP130GP135GK15GK120GK125GS1115G9110GN9120G930GP11TMGP11TMGPZTMRE
	TCMT110202-MM	11 6.35 2.38 2.8 0.2 O
	TCMT110204-MM	11	6.35	2.38	2.8	0.4						●				●
	TCMT110208-MM	11	6.35	2.38	2.8	0.8
	TCMT16T304-MM	16.5	9.525	3.97	4.4	0.4
	TCMT16T308-MM	16.5	9.525	3.97	4.4	0.8C C			C
	TCMT090204-FP	9.6	5.56	2.38	2.5	0.4							0				0
	TCMT110204-FP	11	6.35	2.38	2.8	0.4						0
	TCMT110304-FP	11	6.35	2.38	3.18	0.4
	TCMT16T304-FP	16.5	9.525	3.97	4.4	0.4 0
	TCMT110204-SPL	11	6.35	2.38	2.8	0.4



	TCMT090204-GP	9.6	5.56	2.38	2.5	0.4		···			●			O			●
	TCMT110202-GP	11	6.35	2.38	2.8	0.2		O O		O							●
	TCMT110204-GP	11	6.35	2.38	2.8	0.4		···									O
	TCMT110208-GP	11	6.35	2.38	2.8	0.8		···		●			●●·				○○
	TCMT16T304-GP	16.5	9.525	3.97	4.4	0.4		···				●	··				O
	TCMT16T308-GP	16.5	9.525	3.97	4.4	0.8		···								○○
	TCMT16T312-GP	16.5	9.525	3.97	4.4	1.2
	TCMT220408-GP	22	12.7	4.76	5.56	0.8		O O
	TCMT220412-GP	22	12.7	4.76	5.56	1.2
	TCGT090204-GP	9.6	5.56	2.38	2.5	0.4
	TCGT110202-GP	11	6.35	2.38	2.8	0.2
	TCGT110204-GP	11	6.35	2.38	2.8	0.4
	TCGT110208-GP	11	6.35	2.38	2.8	0.8
	TCGT16T304-GP	16.5	9.525	3.97	4.4	0.4
	TCGT16T308-GP	16.5	9.525	3.97	4.4	0.8							O
T	TCMT090202-TP	9.6	5.56	2.38	2.5 0.2												●
	TCMT090204-TP	9.6	5.56	2.38	2.50.4
	TCMT090208-TP	9.6	5.56	2.38	2.5	0.8											●
	TCMT110204-TP	11	6.35	2.38	2.8	0.4
	CMT110208-TP	11	6.35	2.38	2.80.8												●
	TCMT16T304-TP	16.5	9.525	3.97	4.40.4												●
	TCMT16T308-TP 16.5		9.525	3.97 4.40.8

StockOAvailable Upon Order

Turning Insert (Positive)

Triangle 60° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																		Car-bides			Cermet
Ordering Code		LE	IC	S	D1	RE	GP110	GP620GP	1130GP105	GP115	GP120GP	25GP130GP135	G115GM	125GM	230GM	215GM	20	GM225GK15		GK120	GK125	GST115GST120	GST130	GS15GNT20	G1110	GN1120	GN91130G	P1TM	GP1TM	GPZTM
	TCMT110204-KM 11 6.352.382.80.4
	TCMT16T304-KM	16.5	9.525	3.97	4.4	0.4													●
	TCMT16T308-KM	16.5	9.525	3.97	4.40.8													●

	TCGX090204-AL	9.6	5.56	2.38	2.5	0.4																		●	○〇
	TCGX110202-AL	11	6.35	2.38	2.8	0.2																		●		O
	TCGX110204-AL	11	6.35	2.38	2.8	0.4																		●	○●
	TCGX110208-AL	11	6.35	2.38	2.8	0.8																		●		O
	TCGX16T302-AL	16.5	9.525	3.97	4.40.2																			O
	TCGX16T304-AL	16.5	9.525	3.97	4.4	0.4																		●		O
	TCGX16T308-AL	16.59.5253.97			4.40.8 O O

●Stock OAvailable Upon Order

Turning Insert (Positive)

Triangle 60° with Hole

Ordering Code		Dimension(mm)					Coated Carbides																Car-bides			Cermet
Ordering Code		LE	IC	S	D1	RE	GP110GP120GP130GP105GP		115	GP120	GP225	GP130GP135G15	GM1125	GM230	GM215	GM20	GM25GK	15GK	120GK	125	GS115GST	120GST130 GN20GS115	G110	GN9120	GN91130G	P1TMGP11TMGPZTM
	TPMT110202-MM	11	6.352.382.80.2 ○○ O
	TPMT110204-MM	11	6.35	2.38	2.8	0.4	O	O																		O
	TPMT110304-MM	11	6.35	3.18	3.40.4

	TPMT090204-SPL	9.6	5.56	2.38	2.5	0.4																					●
	TPMT110304-SPL	11	6.35	3.18	3.4	0.4


	TPGT110204-GP	11	6.35	2.38	2.8	0.4										O
	TPGT110208-GP	11	6.35	2.38	2.8	0.8											O
	TPGT16T304-GP	16.5	9.525	3.97	4.4	0.4										O
	TPGT16T308-GP	16.5	9.525	3.97	4.4	0.8										O
	TPMT090202-TP	9.6	5.56	2.38	2.5	0.2																			●
	TPMT090204-TP	9.6	5.56	2.38	2.5	0.4																			o
	TPMT090208-TP	9.6	5.56	2.38	2.5	0.8																			●
	TPMT110302-TP	11	6.35	3.18	3.4	0.2
	TPMT110304-TP	11	6.35	3.18	3.4	0.4																			●
	TPMT110308-TP	11	6.35	3.18	3.4	0.8																			●
	TPMT160302-TP	16.5	9.525	3.18	4.40.2																				●
	TPMT160304-TP	16.5	9.525	3.18	4.4	0.4																			●
	TPMT160308-TP	16.59.525		3.18	4.40.8

Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 35° with Hole

Ordering Code
		Dimension(mm)					Coated Carbides																						Car-bides		Cermet
		LE	IC	S	D1	RE	GP110GP6120GP130GP105				GP115GP120		GP225GP130	GP135G115		GM25	GM230GM	215GM220		GM25GK15		GK20	GS15GST120GST130GS315GN20GK125						G9110GN91120	GN91130	GP1TMGP11TMGPPZTM
		VBMT110304-MM	11.2 6.35 3.18 2.80.4																●
		VBMT110308-MM	11.2	6.35	3.18	2.8	0.8													●	●
		VBMT160402-MM	16.6	9.525	4.76	4.40.2														●	●			●								○○
			VBMT160404-MM	16.6	9.525	4.76	4.4	0.4	●	●	●										●	●				●		●					●	●
			VBMT160408-MM	16.6	9.525	4.76	4.4	0.8	●●●								●				●●				●●		●					●
		R	VBMT160404-FP	16.6	9.525	4.76	4.4	0.4									O						●			●							O
			VBMT160408-FP	16.6	9.525	4.76	4.4	0.8 O								O						●			●							O


	VBMT110304-SPL	11.2	6.35	3.18	2.8	0.4																											●
	VBMT160404-SPL	16.6	9.525	4.76	4.40.4																											●


	VBMT160404-GP	16.6	9.525	4.76	4.4	0.4	●	●	O		●		●			●	●		●	●	●		O							●
	VBMT160408-GP	16.6	9.525	4.76	4.4	0.8		●	O		●	●	●		●	●	●		●	●	●		O							●●
	VBMT160412-GP	16.6	9.525	4.76	4.4	1.2			O		●		O								●

	VBMT110304-TP	11.2	6.35	3.18	2.8	0.4																								●		●
	VBMT110308-TP	11.2	6.35	3.18	2.8	0.8																								●		●
	VBMT160402-TP	16.6	9.525	4.76	4.4	0.2																								●		●
	VBMT160404-TP	16.6	9.525	4.76	4.4	0.4																								●●
	VBMT160408-TP	16.6	9.525	4.76	4.4	0.8																								●
	VBMT160408-KM	16.6	9.525	4.76	4.4	0.8														●		●

●Stock OAvailable Upon Order

Turning Insert (Positive)

Rhombic 35° with Hole

Ordering Code		Dimension(mm)					Car-Coated Carbides Cermetbides
		LE	IC	S	D1	GP110GP620GP130GP105 G115GM25GM230GMM215GM20GM225 GS115GST120GST130 GN120GP115GP120GP225GP130GPP135GK115GK120GK125GS115G9110GN91120GN130GP1TMGP1TMGPZTMRE
		16.6 9.5254.76 4.40.4C O
		VCMT160408-MM	16.6 9.5254.76			4.4 0.8 O


		R	VCMT160408-FP	16.6	9.5254.76 4.40.8 O O



			VCMT110304-SPL	11.2	6.35 3.182.80.4



			VCMT110304-GP	11.2	6.35 3.18		2.8 0.4 O O
			VCMT110308-GP	11.2	6.35	3.18	2.80.8			O			O OC
			VCMT160404-GP	16.6	9.525	4.76	4.40.4			O		O●
		COF	VCMT160408-GP	16.6	9.525	4.76	4.40.8 O					O
		VCGT110304-GP			11.2	6.35		3.18	2.80.4
		VCGT160404-GP	16.6	9.525	4.76	4.40.4
		VCGT160408-GP	16.6	9.525	4.76	4.40.8 O
		VCMT160404-KM	16.6	9.525	4.76	4.40.4
		VCMT160408-KM	16.6	9.5254.76		4.40.8


	VCGX110302-AL	11.2	6.35	3.18	2.8 0.2
	VCGX110304-AL	11.2	6.35	3.18	2.80.4 O
	VCGX110308-AL	11.2	6.35	3.18	2.8 0.8						O
	VCGX160402-AL	16.6	9.5254.76		4.40.2			O
	VCGX160404-AL	16.6	9.5254.76		4.40.4
	VCGX160408-AL	16.6	9.5254.76		4.40.8 O
	VCGX160412-AL	16.6	9.5254.76		4.41.2						O
	VCGX220512-AL	22.1	12.7 5.56		5.61.2 O
	VCGX220516-AL	22.1	12.7 5.56		5.6 1.6
	VCGX220530-AL	22.1 12.7 5.56 5.63.0

●Stock OAvailable Upon Order

Turning Insert (Positive)

Trigon 80° with Hole

Ordering Code

Dimension(mm)

Coated Carbides

Car-bides

Cermet

GP110GPT

GP115

GP120

GP25GP

130GP

135

G115GM

1125

GM230

GMM215

GM220

GM25GK15

GK120

GK125

GS115GST20GST

130

GS115

GN20

G1110GN

9120GN91130

GPE1TMGP11TMGPTM

GP130120GP

105

WCMT06T304-GP 6.5 9.5253.97 4.40.4 O O OWCMT06T308-GP 0.8

O O

9.525

3.97

4.4

0.8

●

●Stock OAvailable Upon Order

Recommended Cutting Data (Negative Inserts)

ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Min-Optimum-Max
ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Cutting Speed Vc(m/min)	Cutting Depth ap(mm)	Feeding Rate f(mm/rev)

Finishing Machining			Continuous		GPT6110 GP1105	240-300-400 220-280-380	0.40-0.80-2.00 0.40-0.80-2.00	0.08-0.15-0.35 0.08-0.15-0.35
					GP1115	200-260-360	0.40-0.80-2.00	0.08-0.15-0.35
General					GPT6120	200-280-380	0.40-0.80-2.00	0.08-0.15-0.35
QF					GP1120	200-260-360	0.40-0.80-2.00	0.08-0.15-0.35
					GP1225	180-240-320	0.40-0.80-2.00	0.08-0.15-0.35
Intermittent					GPT6130	180-240-320	0.40-0.80-2.00	0.08-0.15-0.35
					GP1130	180-240-320	0.40-0.80-2.00	0.08-0.15-0.35
					GP1135	170-220-300	0.40-0.80-2.00	0.08-0.15-0.35
Continuous TF					GP31TM	220-300-380	0.30-0.70-1.80	0.07-0.14-0.35
	GF	GP91TM	200-280-350	0.30-0.70-1.80	0.07-0.14-0.35
			Continuous Intermittent	GP1225	GP1115	200-260-360 180-240-320	0.80-1.20-2.50 0.80-1.20-2.50	0.10-0.20-0.35 0.10-0.20-0.35
			Continuous SPL	GP92TM				0.12-0.20-0.30
				GPT6110		180-240-300	0.40-1.00-2.30	0.15-0.20-0.40
			Continuous		GP1105	220-280-380	0.80-2.00-4.00	0.15-0.20-0.40
			General		GP1115	200-260-360	0.80-2.00-4.00	0.15-0.20-0.40
					GP31TM	180-230-320	0.80-2.00-4.00 0.50-1.20-2.50	0.10-0.18-0.30
					GP91TM	210-280-330
						200-260-330	0.50-1.50-3.00	0.15-0.22-0.35
				QM	GPT6120	180-250-340	0.80-2.00-4.00	0.15-0.20-0.40
	GP1120	180-230-320		0.80-2.00-4.00	0.15-0.20-0.40
Mild Steel ≤HB180	Intermittent	GP1225		160-210-300	0.80-2.00-4.00	0.15-0.20-0.40
P	Semi- finished			GPT6130 GP1130	160-230-300	0.80-2.00-4.00	0.15-0.20-0.40
			GP1135	160-210-300 150-190-280	0.80-2.00-4.00	0.15-0.20-0.40
	Continuous Intermittent	GM	GP1115	180-230-320	0.80-2.00-4.00 1.00-2.00-4.00	0.15-0.20-0.40
			GP1225	160-210-300	1.00-2.00-4.00	0.18-0.22-0.40 0.18-0.22-0.40
			Intermittent	SV	GP1225	160-200-300	1.00-2.50-4.50	0.18-0.25-0.45
			Continuous	TP	GP31TM	220-300-380	0.30-1.00-3.00	0.05-0.12-0.28
					GP91TM	200-280-350	0.30-1.20-3.00	0.05-0.15-0.28
			Continuous	TS	GP31TM GP91TM	200-280-350	0.50-1.00-3.00	0.10-0.15-0.35
			Continuous		GPT6110	200-260-330 150-220-280	0.50-1.20-3.00 1.50-3.50-6.00	0.10-0.20-0.35
									0.20-0.30-0.60
					GP1105	130-190-270	1.50-3.50-6.00	0.20-0.30-0.60
General					GP1115	120-180-250	1.50-3.50-6.00	0.20-0.30-0.60
Rough Finishing	QR				GPT6120	140-210-270	1.50-3.50-6.00	0.20-0.30-0.60
					GP1225	120-170-250	1.50-3.50-6.00	0.20-0.30-0.60
					GPT6130	120-190-250	1.50-3.50-6.00	0.20-0.30-0.60
Intermittent	GP1130					120-170-250	1.50-3.50-6.00	0.20-0.30-0.60
	GP1135					110-150-230	1.50-3.50-6.00	0.20-0.30-0.60
		Continuous			GPT6110	100-170-230	3.00-6.00-12.0	0.35-0.60-1.10
	Heavy				GP1105	100-150-240	3.00-6.00-12.0	0.35-0.60-1.10
	General				GP1115	90-150-210	3.00-6.00-12.0	0.35-0.60-1.10
Machining	QH			GPT6120	100-160-220		3.00-6.00-12.0	0.35-0.60-1.10
				GP1225		90-140-210	3.00-6.00-12.0 0.35-0.60-1.10
			Intermittent	GPT6130 GP1135	90-150-210 80-130-190	3.00-6.00-12.0 3.00-6.00-12.0	0.35-0.60-1.10 0.35-0.60-1.10

Recommended Cutting Data (Negative Inserts)

ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Min-Optimum-Max
ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Cutting Speed Vc(m/min)	Cutting Depth ap(mm)	Feeding Rate f(mm/rev)
					Continuous	GPT6110	220-270-360	0.40-0.80-2.00	0.08-0.15-0.35
						GP1105	200-250-340	0.40-0.80-2.00	0.08-0.15-0.35
						GP1115	180-230-320	0.40-0.80-2.00	0.08-0.15-0.35
				General		GPT6120 180-250-340	0.40-0.80-2.00	0.08-0.15-0.35
					QF GP1120	180-230-320	0.40-0.80-2.00	0.08-0.15-0.35
				Finishing	GP1225	160-200-300	0.40-0.80-2.00	0.08-0.15-0.35
	Machining Intermittent	GPT6130		160-220-300	0.40-0.80-2.00	0.08-0.15-0.35
		GP1130 GP1135		180-240-320	0.40-0.80-2.00	0.08-0.15-0.35
				Continuous	GP1115	150-200-280 180-230-320	0.40-0.80-2.00	0.08-0.15-0.35 0.10-0.20-0.35
				Intermittent	GF GP1225	160-200-300	0.80-1.20-2.50 0.80-1.20-2.50	0.10-0.20-0.35
			Continuous	SPL GP92TM	160-210-290	0.40-1.00-2.30	0.12-0.20-0.30
				GPT6110		0.80-2.00-4.00	0.15-0.22-0.40
				GP1105	180-250-340	0.80-2.00-4.00
			Continuous	GP1115	160-230-320 140-210-300	0.80-2.00-4.00	0.15-0.22-0.40
					GP31TM 200-250-330			0.15-0.20-0.40 0.10-0.18-0.30
						GP91TM	180-230-310	0.50-1.20-2.50 0.50-1.50-3.00	0.15-0.20-0.35
	QM General	GPT6120	140-230-320			0.80-2.00-4.00	0.15-0.20-0.40
		GP1120	140-210-300			0.80-2.00-4.00	0.15-0.20-0.40
		GP1225	120-190-280			0.80-2.00-4.00	0.15-0.20-0.40
	Semi- finished Intermittent	GPT6130	120-210-280			0.80-2.00-4.00	0.15-0.20-0.40
	GP1130	120-190-280	0.80-2.00-4.00			0.15-0.20-0.40
P Steel	Carbon Steel, Alloy HB180-280	Continuous				GP1135	100-170-260	0.80-2.00-4.00	0.15-0.20-0.40
			Intermittent	GM	GP1115 GP1225	140-210-300	1.00-2.00-4.00 1.00-2.00-4.00	0.18-0.22-0.40
			Intermittent	SV GP1225	120-190-280 120-180-280	1.00-2.50-4.50		0.18-0.22-0.40 0.18-0.25-0.45
			Continuous	TP	GP31TM	200-270-350	0.30-1.00-2.50	0.05-0.12-0.28
			Continuous	GP91TM	180-250-330	0.30-1.20-2.50	0.05-0.15-0.28
			Continuous	TS	GP31TM	180-250-330	0.50-1.00-3.00	0.10-0.15-0.35
		GP91TM	Continuous	TS	180-230-310	0.50-1.20-3.00	0.10-0.20-0.35
			Continuous		GPT6110	140-210-270	1.50-3.50-6.00	0.20-0.30-0.60
			Continuous		GP1105	120-180-260	1.50-3.50-6.00	0.20-0.30-0.60
			General		GP1115	110-170-240	1.50-3.50-6.00	0.20-0.30-0.60
	Rough Finishing	QR			GPT6120 130-200-260	1.50-3.50-6.00	0.20-0.30-0.60
					GP1225 110-160-240	1.50-3.50-6.00	0.20-0.30-0.60
	Intermittent				GPT6130 110-180-240	1.50-3.50-6.00	0.20-0.30-0.60
				GP1130	110-160-240	1.50-3.50-6.00	0.20-0.30-0.60
					GP1135	100-140-220	1.50-3.50-6.00 3.00-6.00-12.0	0.20-0.30-0.60
		Continuous			GPT6110	90-160-220		0.35-0.60-1.10
			Heavy		GP1105	90-140-230	3.00-6.00-12.0	0.35-0.60-1.10
		General			GP1115	80-140-200	3.00-6.00-12.0	0.35-0.60-1.10
		Machining			QH	GPT6120 90-150-210	3.00-6.00-12.0	0.35-0.60-1.10
		Intermittent			GP1225	80-130-200	3.00-6.00-12.0	0.35-0.60-1.10
					GPT6130	80-140-200	3.00-6.00-12.0	0.35-0.60-1.10
					GP1135 70-120-180	3.00-6.00-12.0	0.35-0.60-1.10

Recommended Cutting Data (Negative Inserts)

ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Min-Optimum-Max
ISO	Workpiece Materials	Hardness	Application Range	Cutting Mode	Chip Breaker	Grade	Cutting Speed Vc(m/min)	Cutting Depth ap(mm)	Feeding Rate f(mm/rev)
P					Continuous	GPT6110	180-220-290	0.40-0.80-2.00		0.08-0.15-0.35
						GP1105	160-200-270	0.40-0.80-2.00	0.08-0.15-0.35
	GP1115						150-180-250	0.40-0.80-2.00	0.08-0.15-0.35
General	QF					GPT6120	150-200-270	0.40-0.80-2.00	0.08-0.15-0.35
						GP1120	150-180-250	0.40-0.80-2.00	0.08-0.15-0.35
Finishing						GP1225	100-150-220	0.80-2.00-4.00	0.15-0.20-0.40
Machining Intermittent						GPT6130	130-170-230	0.40-0.80-2.00	0.08-0.15-0.35
	GP1130						130-150-230	0.40-0.80-2.00	0.08-0.15-0.35
Continuous	GP1135					110-130-210		0.40-0.80-2.00	0.08-0.15-0.35
		Intermittent	GF	GP1115 GP1225	150-180-250		0.80-1.20-2.50 0.80-1.20-2.50	0.10-0.20-0.35 0.10-0.20-0.35
		Continuous		SPL GP92TM		130-150-230	0.40-1.00-2.30	0.12-0.20-0.30
						150-190-280	0.80-2.00-4.00	0.15-0.20-0.40
				GP1105 GP1115	GPT6110	140-200-270 120-180-250	0.80-2.00-4.00	0.15-0.20-0.40
			Continuous			110-170-240	0.80-2.00-4.00	0.15-0.20-0.40
				GP31TM		180-230-320	0.50-1.20-2.50	0.10-0.18-0.30
					GP91TM	160-210-300	0.50-1.50-3.00	0.15-0.22-0.35
			General	QM	GPT6120	110-190-260	0.80-2.00-4.00	0.15-0.20-0.40
			GP1120	110-170-240	0.80-2.00-4.00	0.15-0.20-0.40
			GP1225	100-150-220	0.80-2.00-4.00	0.15-0.20-0.40
Semi- finished	Intermittent		GPT6130	100-170-220	0.80-2.00-4.00
			GP1130	100-150-220	0.80-2.00-4.00	0.15-0.20-0.40	0.15-0.20-0.40
Steel, Alloy Steel	HB280-350			GP1135	900-130-200	0.80-2.00-4.00	0.15-0.20-0.40
		Continuous	GM	GP1115	110-170-240	1.00-2.00-4.00	0.18-0.22-0.40
		Intermittent		GP1225	100-150-220	1.00-2.00-4.00		0.18-0.22-0.40
			Intermittent	SV	GP1225	100-140-220	1.00-2.50-4.50	0.18-0.25-0.45
			Continuous	TP	GP31TM	180-250-320	0.30-1.00-2.50	0.05-0.12-0.28
			Continuous	TS	GP91TM GP31TM	170-230-300	0.30-1.20-2.50 0.50-1.00-3.00	0.05-0.15-0.28 0.10-0.15-0.35
					GP91TM	170-230-300 150-210-280	0.50-1.20-3.00	0.10-0.20-0.35
			Continuous		GPT6110	120-190-230	2.00-3.50-6.50	0.20-0.30-0.60
					GP1105	100-150-210	2.00-3.50-6.50	0.20-0.30-0.60
					GP1115	90-150-200	2.00-3.50-6.50	0.20-0.30-0.60
		Rough Finishing	General	QR	GPT6120	110-180-220	2.00-3.50-6.50	0.20-0.30-0.60
					GP1225	90-140-200	2.00-3.50-6.50	0.20-0.30-0.60
			Intermittent		GPT6130	90-160-200	2.00-3.50-6.50	0.20-0.30-0.60
					GP1130	90-140-200	2.00-3.50-6.50	0.20-0.30-0.60
					GP1135	80-120-180	2.00-3.50-6.50	0.20-0.30-0.60
			Continuous		GPT6110	80-130-190	3.00-6.00-12.0	0.35-0.60-1.10
					GP1105	80-110-190	3.00-6.00-12.0	0.35-0.60-1.10
		Heavy Machining	General		GP1115	70-110-170	3.00-6.00-12.0	0.35-0.60-1.10
				QH	GPT6120	80-120-180	3.00-6.00-12.0	0.35-0.60-1.10
					GP1225	70-100-170	3.00-6.00-12.0	0.35-0.60-1.10
			Intermittent		GPT6130	70-110-170	3.00-6.00-12.0	0.35-0.60-1.10
					GP1135	60-90-150	3.00-6.00-12.0	0.35-0.60-1.10

Recommended Cutting Data (Negative Inserts)

ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreak-er		Grade	Min-Optimum-Max
ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreak-er		Grade	Cutting SpeedVc(m/min)	Cutting Depthap(mm)	Feeding Ratef(mm/rev)
M	MartensiticFerriteSUS410SUS430etc.	≤HB230	FinishingMachining	General	SF		GS3115	120-190-250	0.10-0.80-1.50	0.08-0.10-0.30
				General	SF		GM3220	100-150-200	0.10-0.80-1.50	0.08-0.12-0.25
				General	YF		GM3220	100-150-200	0.10-1.0-2.0	0.08-0.15-0.3
			Semi-finished	Continuous			GM1115	200-250-300	0.50-1.20-2.00	0.10-0.20-0.40
				Continuous			GM3215	120-160-200	1.00-2.00-3.00	0.15-0.20-0.30
				General	SM		GM3220	60-130-180	1.00-2.00-3.00	0.15-0.20-0.35
				Intermittent			GM1125	180-230-280	0.50-1.80-3.00	0.10-0.20-0.40
							GM1230	180-230-280	0.50-1.80-3.00	0.10-0.20-0.40
							GM3225	60-130-180	1.00-2.00-3.00	0.15-0.20-0.35
				Continuous			GM1115	200-250-300	0.80-1.80-3.50	0.08-0.18-0.40
				Continuous			GM3215	120-160-200	0.80-1.80-3.50	0.08-0.18-0.30
				General	LM		GM3220	60-130-180	0.80-1.80-3.50	0.08-0.20-0.40
				Intermittent			GM1125	180-230-280	0.80-1.80-3.50	0.08-0.18-0.40
							GM1230	180-230-280	0.80-1.80-3.50	0.08-0.18-0.40
							GM3225	60-130-180	0.80-1.80-3.50	0.08-0.20-0.40
			RoughFinishing	Continuous			GM1115	200-250-300	1.50-3.00-5.00	0.15-0.30-0.50
				General	LR		GM3220	60-130-180	1.50-3.00-5.00	0.15-0.30-0.50
				Intermittent	LR		GM3225	60-130-180	1.50-3.00-5.00	0.15-0.30-0.50
	AusteniteSUS201SUS304SUS316etc.	≤HB250	FinishingMachining	General	SF		GS3115	120-190-250	0.10-0.80-1.50	0.08-0.10-0.30
				General	SF		GM3220	80-130-180	0.10-0.80-1.50	0.08-0.12-0.25
				General	YF		GM3220	80-130-180	0.10-1.0-2.0	0.08-0.15-0.3
			Semi-finished	Continuous			GM1115	180-230-280	0.50-1.20-2.00	0.10-0.20-0.40
				Continuous						GM3215	100-130-160	1.00-2.00-3.00	0.15-0.20-0.30
				General	SM					GM3220	60-110-150	1.00-2.00-3.00	0.15-0.20-0.35
				Intermittent			GM1125	180-230-280	0.50-1.80-3.00	0.10-0.20-0.40
							GM1230	180-230-280	0.50-1.80-3.00	0.10-0.20-0.40
							GM3225	60-110-150	1.00-2.00-3.00	0.15-0.20-0.35
				Continuous	LM		GM1115	200-250-300	0.80-1.80-3.50	0.08-0.18-0.40
				Continuous			GM3215	100-130-160	0.80-1.80-3.50	0.08-0.18-0.30
				General			GM3220	60-110-150	0.80-1.80-3.50	0.08-0.20-0.40
				Intermittent			GM1125	160-200-240	0.80-1.80-3.50	0.08-0.18-0.40
							GM1230	160-200-240	0.80-1.80-3.50	0.08-0.18-0.40
							GM3225	60-110-150	0.80-1.80-3.50	0.08-0.20-0.40
			RoughFinishing	Continuous			GM1115	180-230-280	1.50-3.00-5.00	0.15-0.30-0.50
				General	LR				GM3220	60-110-150	1.50-3.00-5.00	0.15-0.30-0.50
				General	LR	LR			GM3220	60-110-150	1.50-3.00-5.00	0.15-0.30-0.50
				Intermittent			GM3225	60-110-150	1.50-3.00-5.00	0.15-0.30-0.50

Recommended Cutting Data (Negative Inserts)

ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreak-er	Grade	Min-Optimum-Max
ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreak-er	Grade	Cutting SpeedVc(m/min)	Cutting Depthap(mm)	Feeding Ratef(mm/rev)
K	FerrosteelFC200FC250FC300etc.	≤HB220	Semi-finished	Continuous	WMV	GK1115	230-350-500	1.00-2.00-6.00	0.20-0.40-0.80
				Intermittent	WMV	GK1125	220-320-480	1.00-2.00-6.00	0.20-0.40-0.80
				Continuous		GK1115	230-350-500	0.50-1.50-3.00	0.10-0.20-0.40
				General	MK	GK1120	230-320-500	0.50-1.50-3.00	0.10-0.20-0.40
				Intermittent		GK1125	220-320-480	0.50-1.50-3.00	0.10-0.20-0.40
				Continuous		GK1115	230-350-500	0.50-1.50-3.00	0.10-0.20-0.40
				General	UK	GK1120	230-320-500	0.50-1.50-3.00	0.10-0.20-0.40
				Intermittent		GK1125	220-320-480	0.50-1.50-3.00	0.10-0.20-0.40
			RoughFinishing	Continuous		GK1115	220-320-480	0.50-2.00-4.00	0.10-0.25-0.50
				General	HK	GK1120	220-300-480	0.50-2.00-4.00	0.10-0.25-0.50
				Intermittent		GK1125	210-300-450	0.50-2.00-4.00	0.10-0.25-0.50
			HeavyMachining	Continuous		GK1115	210-300-450	1.00-2.50-6.00	0.20-0.30-0.60
				General	Flat	GK1120	210-280-450	1.00-2.50-6.00	0.20-0.30-0.60
				Intermittent		GK1125	200-280-430	1.00-2.50-6.00	0.20-0.30-0.60
	Nodular CastIronFCD450FCD500FCD600etc.	≤HB300	Semi-finished	Continuous	WMV	GK1115	180-260-380	1.00-2.00-6.00	0.20-0.40-0.80
				Intermittent	WMV	GK1125	160-230-350	1.00-2.00-6.00	0.20-0.40-0.80
				Continuous		GK1115	180-260-380	0.50-1.50-3.00	0.10-0.20-0.40
				General	MK	GK1120	180-260-380	0.50-1.50-3.00	0.10-0.20-0.40
				Intermittent		GK1125	160-230-350	0.50-1.50-3.00	0.10-0.20-0.40
				Continuous		GK1115	180-260-380	0.50-1.50-3.00	0.10-0.20-0.40
				General	UK	GK1120	180-260-380	0.50-1.50-3.00	0.10-0.20-0.40
				Intermittent		GK1125	160-230-350	0.50-1.50-3.00	0.10-0.20-0.40
			RoughFinishing	Continuous		GK1115	180-240-360	0.50-2.00-4.00	0.10-0.25-0.50
				General	HK	GK1120	180-240-360	0.50-2.00-4.00	0.10-0.25-0.50
				Intermittent		GK1125	160-230-350	0.50-2.00-4.00	0.10-0.25-0.50
			HeavyMachining	Continuous		GK1115	180-220-350	1.00-2.50-6.00	0.20-0.30-0.60
				General	FLAT	GK1120	180-220-350	1.00-2.50-6.00	0.20-0.30-0.60
				Intermittent		GK1125	160-230-350	1.00-2.50-6.00	0.20-0.30-0.60
S	Super alloyTitaniumAlloy	≤HRC45	Finishingto Semi-finishing	Continuous		GST7115	20-40-70	0.50-1.50-3.00	0.10-0.15-0.22
				General	EL	GST7120	20-40-70	0.50-1.50-3.00	0.10-0.15-0.22
				Intermittent		GST7125	20-30-40	0.50-1.50-3.00	0.10-0.15-0.22
				Continuous		GST7115	20-40-70	0.50-1.50-3.00	0.10-0.20-0.30
				General	SML	GST7120	20-40-70	0.50-1.50-3.00	0.10-0.20-0.30
				Intermittent		GST7125	20-30-40	0.50-1.50-3.00	0.10-0.20-0.30
			Semi-finished	Continuous		GST7115	20-40-70	1.00-2.50-4.00	0.10-0.20-0.35
				General	EM	GST7120	20-40-70	1.00-2.50-4.00	0.10-0.20-0.35
				Intermittent		GST7125	20-30-40	1.00-2.50-4.00	0.10-0.20-0.35
				Continuous		GST7115	20-40-70	1.00-2.50-4.00	0.10-0.25-0.40
				General	SMM	GST7120	20-40-70	1.00-2.50-4.00	0.10-0.25-0.40
				Intermittent		GST7125	20-30-40	1.00-2.50-4.00	0.10-0.25-0.40

Recommended Cutting Data (Positive Inserts)

ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreaker	Grade	Min-Optimum-Max
ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreaker		Cutting SpeedVc(m/min)	Cutting Depthap(mm)	Feeding Ratef(mm/rev)
PCarbonSteel, AlloySteelHB280-350					FinishingMachining				GP31TM
							Continuous		GP91TM	200-250-310	0.10-0.60-1.50	0.03-0.10-0.20
								MM	GPT6110	210-260-340	0.10-0.60-1.50	0.05-0.10-0.20
							General		GPT6120	180-240-320	0.10-0.60-1.50	0.05-0.10-0.20
							Intermittent		GPT6130	170-220-280	0.10-0.60-1.50	0.05-0.10-0.20
							Continuous		GP31TM	220-280-340	0.10-0.50-1.00	0.06-0.11-0.25
							Continuous		GP91TM	200-250-310	0.10-0.50-1.00	0.06-0.11-0.25
								FP	GPT6110	210-260-340	0.10-0.50-1.00	0.06-0.11-0.25
						General		GPT6120	180-240-320	0.10-0.50-1.00	0.06-0.11-0.25
						Intermittent		GPT6130	170-220-280	0.10-0.50-1.00	0.06-0.11-0.25
						Continuous	SPL	GP92TM	180-240-300	0.30-0.80-2.00	0.07-0.12-0.26
					Semi-finishingto Rough-finish	General	GP	GP1120	170-200-280	0.40-1.00-2.50	0.07-0.12-0.30
					Semi-finishingto Rough-finish	Intermittent		GP1130	150-180-260	0.40-1.00-2.50	0.07-0.12-0.30
					Semi-finished	Continuous	TP	GP31TM	200-250-300	0.30-1.00-3.00	0.05-0.15-0.25
					Semi-finished	Continuous	TP	GP91TM	180-230-300	0.30-1.00-3.00	0.05-0.15-0.25
				FinishingMachining			GP31TM	200-250-330	0.10-0.50-1.00	0.03-0.10-0.20
					Continuous		GP91TM	180-230-300	0.10-0.60-1.50	0.03-0.12-0.20
						MM	GPT6110	180-220-290	0.10-0.60-1.50	0.05-0.10-0.20
					General		GPT6120	150-200-280	0.10-0.60-1.50	0.05-0.10-0.20
					Intermittent		GPT6130	140-180-240	0.10-0.60-1.50	0.05-0.10-0.20
					Continuous		GP31TM	200-250-330	0.10-0.50-1.00	0.06-0.11-0.25
						FP	GP91TM	180-230-300	0.10-0.50-1.00	0.06-0.11-0.25
						FP	GPT6110	180-220-290	0.10-0.50-1.00	0.06-0.11-0.25
					General		GPT6120	150-200-280	0.10-0.50-1.00	0.06-0.11-0.25
					Intermittent		GPT6130	140-180-240	0.10-0.50-1.00	0.06-0.11-0.25
				Semi-finishing	General	GP	GP1120	140-160-240	0.40-1.00-2.50	0.07-0.12-0.30
				to Rough-finish	Intermittent	GP	GP1130	120-140-220	0.40-1.00-2.50	0.07-0.12-0.30
				Semi-finished	Continuous	TP	GP31TM	180-210-280	0.30-1.00-3.00	0.05-0.15-0.25
				Semi-finished	Continuous	TP	GP91TM	160-190-270	0.30-1.00-3.00	0.05-0.15-0.25
			FinishingMachining	Continuous		GP31TM	160-220-300	0.10-0.60-1.50	0.03-0.10-0.20
						GP91TM	140-200-280	0.10-0.60-1.50	0.03-0.10-0.20
					MM	GPT6110	160-200-260	0.10-0.60-1.50	0.05-0.10-0.20
				General		GPT6120	130-180-250	0.10-0.60-1.50	0.05-0.10-0.20
				Intermittent		GPT6130	120-160-210	0.10-0.60-1.50	0.05-0.10-0.20
				Continuous	FP	GP31TM	160-220-300	0.10-0.50-1.00	0.06-0.11-0.25
						GP91TM	140-200-280	0.10-0.50-1.00	0.06-0.11-0.25
						GPT6110	160-200-260	0.10-0.50-1.00	0.06-0.11-0.25
				General		GPT6120	130-180-250	0.10-0.50-1.00	0.06-0.11-0.25
				Intermittent		GPT6130	120-160-210	0.10-0.50-1.00	0.06-0.11-0.25
			Semi-finishingto Rough-finish	General	GP	GP1120	120-160-210	0.40-1.00-2.50	0.07-0.12-0.30
			Semi-finishingto Rough-finish	Intermittent		GP1130	100-140-220	0.40-1.00-2.50	0.07-0.12-0.30
			Semi-finished	Continuous	TP	GP31TM	160-200-270	0.30-1.00-3.00	0.05-0.12-0.25
			Semi-finished	Continuous	TP	GP91TM	130-160-250	0.30-1.20-3.00	0.05-0.15-0.25

Recommended Cutting Data (Positive Inserts)

ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreaker	Grade	Min-Optimum-Max
ISO	WorkpieceMaterials	Hardness	ApplicationRange	CuttingMode	ChipBreaker		Cutting SpeedVc(m/min)	Cutting Depthap(mm)	Feeding Ratef(mm/rev)
	MartensiticFerriteSUS410	≤HB300	Finishingto Semi-finishing	Continuous		GM1115	200-250-300	0.40-0.70-1.50	0.05-0.10-0.20
				General	MM	GM3220	40-80-140	0.40-0.70-1.50	0.05-0.10-0.20
				Intermittent		GM3225	40-80-140	0.40-0.70-1.50	0.05-0.10-0.20
				Continuous		GM1115	200-250-300	0.10-0.50-1.00	0.06-0.11-0.25
				General	FP	GM3220	40-80-140	0.10-0.50-1.00	0.06-0.11-0.25
				Intermittent		GM3225	40-80-140	0.10-0.50-1.00	0.06-0.11-0.25
	SUS430		Semi-finishingto Rough-	Continuous		GM1115	150-200-250	0.50-1.00-2.50	0.07-0.12-0.30
				Continuous		GM3315	60-100-160	0.50-1.00-2.50	0.07-0.12-0.25
				General	GP	GM3220	40-80-140	0.50-1.00-2.50	0.07-0.12-0.30
			finish	Intermittent		GM1230	120-150-180	0.50-1.00-2.50	0.07-0.12-0.30
			finish	Intermittent		GM3325	40-80-140	0.50-1.00-2.50	0.07-0.12-0.30
	AusteniteSUS201SUS304SUS316	≤HB250	Finishingto Semi-finishing	Continuous		GM1115	200-240-300	0.50-0.70-1.50	0.05-0.10-0.20
				General	MM	GM3220	40-70-140	0.50-0.70-1.50	0.05-0.10-0.20
				Intermittent		GM3225	40-70-140	0.50-0.70-1.50	0.05-0.10-0.20
				Continuous		GM1115	200-250-300	0.10-0.50-1.00	0.06-0.11-0.25
				General	FP	GM3220	40-80-140	0.10-0.50-1.00	0.06-0.11-0.25
				Intermittent		GM3225	40-80-140	0.10-0.50-1.00	0.06-0.11-0.25
			Semi-finishingto Rough-finish	Continuous		GM1115	150-190-250	0.40-1.00-2.50	0.07-0.12-0.30
				Continuous		GM3315	50-90-150	0.40-1.00-2.50	0.07-0.12-0.25
				General	GP	GM3220	40-70-140	0.40-1.00-2.50	0.07-0.12-0.30
				Intermittent		GM1230	120-140-180	0.40-1.00-2.50	0.07-0.12-0.30
				Intermittent		GM3325	40-70-140	0.40-1.00-2.50	0.07-0.12-0.30
	FerrosteelFC200FC250FC300etc.	≤HB250	FinishingMachining	Continuous	FP	GK1115	180-260-360	0.10-0.50-1.00	0.06-0.11-0.25
			Finishingto Semi-finishing	Continuous		GK1215	180-280-380	0.30-0.80-2.00	0.05-0.12-0.25
				General	GP	GK1220	180-260-380	0.30-0.80-2.00	0.05-0.12-0.25
				Intermittent		GK1225	160-250-350	0.30-0.80-2.00	0.05-0.12-0.25
			Semi-finishingto Rough-finish	Continuous		GK1115	180-260-360	1.00-2.00-4.00	0.13-0.20-0.40
				General	KM	GK1120	180-240-360	1.00-2.00-4.00	0.13-0.20-0.40
				Intermittent		GK1125	160-230-340	1.00-2.00-4.00	0.13-0.20-0.40
	NodularCastFCD450FCD500FCD600etc.	≤HB270	FinishingMachining	Continuous	FP	GK1115	180-260-360	0.10-0.50-1.00	0.06-0.11-0.25
			Finishingto Semi-finishing	Continuous		GK1215	160-250-350	0.30-0.80-2.00	0.05-0.12-0.25
				General	GP	GK1220	160-220-350	0.30-0.80-2.00	0.05-0.12-0.25
				Intermittent		GK1225	140-230-330	0.30-0.80-2.00	0.05-0.12-0.25
			Semi-finishingto Rough-	Continuous		GK1115	160-230-330	1.00-2.00-4.00	0.13-0.20-0.40
			Semi-finishingto Rough-	General	KM	GK1120	160-200-330	1.00-2.00-4.00	0.13-0.20-0.40
			finish	Intermittent		GK1125	140-200-310	1.00-2.00-4.00	0.13-0.20-0.40
	Aluminum	HardenHB90-100	Finishingto Semi-finishing	General	AL	GN9110	250-700-970	0.50-1.20-3.00	0.05-0.10-0.30
		HardenHB90-100				GN9120	250-680-960	0.50-1.20-3.50	0.05-0.10-0.30
		UntreatedHB60-90				GN9130	250-650-950	0.50-1.20-4.00	0.05-0.10-0.30
		UntreatedHB60-90				GNT7120	950-1300-2000	0.50-1.20-3.50	0.05-0.10-0.30

MEMO

SMALL PART TURNING TOOLS

List of Small Part Turning Inserts Small Part Turning Inserts (Negative)

Geometry	Features	Range Of Machining	Geometry Section
P	• The skewed slot design stably controls the removal direction of chips. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.	ap [mm] 2.5 1.5 0. 0 0.05 0.1 0.15 0.2 0.250.3 f[mm/rev]
G	• The circular arc slot design improves the sharpness of the cutting edge while ensuring the strength of the tip. • The design of a long cutting edge meets the requirement of a relatively large cutting depth.
S	• The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.	ap [mm] 2.5 1.5 0. 0.05 0.1 0.15 0.2 0.25 0.3 f [mm/rev]
AK	• The design of a sharp edge meets the requirements for good machined surface quality. • The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance.	ap [mm] 4 3 2 0.05 0.15 f [mm/rev. 0 0.1

80° Diamond	55° Diamond	90° Square	60° Regular Triangle	35° Diamond	80° Hexagon

			TNGG-P
			P090

			TNGG-G
			P090

			TNGG-S
			P090

			TNGG-AK
			P090

List of Small Part Turning Inserts

5° Relief Angle

Small Part Turning Inserts (Positive)

Geometry	Features	Range Of Machining	Geometry Section
P	• The skewed slot design stably controls the removal direction of chips. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.
G	• The circular arc slot design improves the sharpness of the cutting edge while ensuring the strength of the tip. • The design of a long cutting edge meets the requirement of a relatively large cutting depth.
S	• The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.
AF	• The design of a small slot width meets the chip breaking requirements in the field of tiny cutting depths. • The design of a large rake angle reduces the cutting resistance and achieves excellent machined surface quality.
BF	• The special chip breaker design promotes chip curling and facilitates chip removal. • The design of a small rake angle features high strength of the tip and high versatility.	ap [mm] 0 0.05 0.1 0.15 f [mm/rev]
SK	• The design of sharp edge and tool cutting edge inclination angle enhances the sharpness of the cutting edges and effectively reduces the cutting force. · The brand-new chip breaker design improves the chip breaking in the machining of steel and stainless steel
BK	with smalī cutting depths. • The design of a large slot width enables smooth chip removal and achieves stable machining. • The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance.
MM	• The design of twin rake angles takes both sharpness and strength into account, and has a wide machining range. • The design of a double-curved chip breaker promotes stable chip curling and has excellent performance in chip breaking and chip removal.	ap[mm] 4 3 2 0.05 0.1 0.15 f [mm/rev] 0

80° Diamond	55º Diamond	90º Square	60° Regular Triangle	35° Diamond	80° Hexagon

			TBGT-P	VBGT-P	WBGT-P
			P098	P101	P106

				VBGT-G
				P101

				VBGT-S
				P102

				VBGT-AF
				P102

				VBGT-BF
				P102

				VBGT-SK
				P102

				VBGT-BK
				P102

				VBGT-MM
				P102

List of Small Part Turning Inserts

7° Relief Angle

Small Part Turning Inserts (Positive)

Geometry	Features	Range Of Machining	Geometry Section
P	• The skewed slot design stably controls the removal direction of chips. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.
G	• The circular arc slot design improves the sharpness of the cutting edge while ensuring the strength of the tip. • The design of a long cutting edge meets the requirement of a relatively large cutting depth.	ap [mm] 3 2.5 2 1.5 0.5 0 0.05 0.1 0.15 0.2 0.25 0.3 f[mm/rev]
S	• The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.
AF	• The design of a small slot width meets the chip breaking requirements in the field of tiny cutting depths. • The design of a large rake angle reduces the cutting resistance and achieves excellent machined surface quality.	ap [mm] 4 3 2 0.05 0.1 0.15 f[mm/rev] 0
AK	• The design of a sharp edge meets the requirements for good machined surface quality. • The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance.	ap [mm] 4 3 2 1 0 0.05 0.1 0.15 f[mm/rev]

80° Diamond 55° DiamondCCGT-PP091 CCGT-G DCGT-G		90° Square	60° Regular Triangle	35° Diamond	80° Hexagon

		DCGT-P		TCGT-P	VCGT-P
				P099	P103

		DCGT-G		TCGT-G	VCGT-G
					P099	P103

	DCGT-S			VCGT-S
	P096			P103

	DCGT-AF			VCGT-AF
	P097			P104

	DCGT-AK
	P097

List of Small Part Turning Inserts

Small Part Turning Inserts (Positive)

7° Relief Angle

Geometry	Features	Range Of Machining		Geometry Section
BF	• The special chip breaker design promotes chip curling and facilitates chip removal. • The design of a small rake angle features high strength of the tip and high versatility.	ap [mm] 4 3 2 0 0.05 0.1	0.15 f [mm/rev]
SK	• The design of sharp edge and tool cutting edge inclination angle enhances the sharpness of the cutting edges and effectively reduces the cutting force. • The brand-new chip breaker design improves the chip breaking in the machining of steel and stainless steel with small cutting depths.	ap [mm] 4 3 2 1 0.05 0.1 0	0.15 f[mm/rev]	12°
BK	• The design of a large slot width enables smooth chip removal and achieves stable machining. • The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance.	ap [mm] 3 2 0.05 0.1 0	0.15 f[mm/rev]
MM	• The design of twin rake angles takes both sharpness and strength into account, and has a wide machining range. • The design of a double-curved chip breaker promotes stable chip curling and has excellent performance in chip breaking and chip removal.	ap [mm] 4 3 2 0 0.05 0.1 0.15 f [mm/rev]	15°8°

80° Diamond	55° Diamond	90° Square	60° Regular Triangle	35° Diamond	80° Hexagon

CCGT-BF	DCGT-BF			VCGT-BF
P094	P097			P104

	DCGT-SK
	P097
				L
CCGT-BK	DCGT-BK			VCGT-BK
P094	P097			P104

	DCGT-MM			VCGT-MM
	P097			P104

List of Small Part Turning Inserts Small Part Turning Inserts (Positive)

11° Relief Angle

Geometry	Features	Range Of Machining	Geometry Section
P	• The skewed slot design stably controls the removal direction of chips. • With a design of thin edge, the cutting edge is sharp and can effectively reduce the cutting force.
G	• The circular arc slot design improves the sharpness of the cutting edge while ensuring the strength of the tip. • The design of a long cutting edge meets the requirement of a relatively large cutting depth.	ap [mm] 3 2.5 2 1.5 0.5 0 0.05 0.1 0.15 0.2 0.250.3 f[mm/rev]
BK	• The design of a large slot width enables smooth chip removal and achieves stable machining • The design of the tool cutting edge inclination angle controls the flow direction of chips and reduces the cutting resistance.	ap [mm] 8 3 2 1 0 0.05 0.1 0.15 f[mm/rev]

80° Diamond	55° Diamond	90° Square	60° Regular Triangle	35° Diamond	80° Hexagon

			TPGT(H)-P	VPGT-P
			P100	P105

			TPGT-G	VPGT-G
			P100	P105
				L
				VPGT-BK
				P105

List of Small Part Turning Inserts Small Part Turning Inserts (Other)

Back-turning

Geometry	Features	Range of Machining	Geometry Section
GSAB	• The special shape design meets the requirements of back-turning. • The special geometry design enables stable control of the flow direction of chips.
GSTB	• The vertically-installed structure design ensures firm clamping and realizes stable cutting. • The skewed slot design effectively controls the direction of chip removal.	ap [mm]	0.1 0.2 f[mm/rev]

Schematic Diagram of Small Part Tool Machining

Parting Off (P218)

Backturning (P97)
External Diameter Machining
Grooving Machining (P218)
Threading (P286)
End Face Machining

Appearance

GSAB P107

GSTB P108

Three-dimensional Chip Breaker and General Grooving Type Representation Method

DCGT11T302

(M)

(E)

(R)

Tip Arc Is of Negative Tolerance

Cutting Edge Treatment

Insert Direction

Turning Insert (Negative)

Triangle 60° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	TNGG160401L-P	16.5	9.525	4.76 3.81		0.1
	TNGG160401R-P	16.5	9.525	4.76	3.81	0.1
	TNGG160402L-P	16.5	9.525	4.76	3.81	0.2
	TNGG160402R-P	16.5	9.525	4.76	3.81	0.2
	TNGG160404L-P	16.5	9.525	4.76	3.81	0.4
	TNGG160404R-P	16.5	9.525	4.76	3.81	0.4
	TNGG160408L-P	16.5	9.525	4.76	3.81	0.8	O			O
	TNGG160408R-P	16.5	9.525	4.76	3.81	0.8	O	O		O
	TNGG160404L-G	16.5	9.525	4.76	3.81	0.4
	TNGG160404R-G	16.5	9.525	4.76	3.81	0.4
	TNGG160408L-G	16.5	9.525	4.76	3.81	0.8
	TNGG160408R-G	16.5	9.525	4.76	3.81	0.8
	TNGG160404R-S	16.5	9.525	4.76	3.81	0.4



	TNGG160401M-AK	16.5	9.525	4.76	3.81	<0.1
	TNGG160402M-AK	16.5	9.525	4.76	3.81	<0.2
	TNGG160404M-AK	16.5	9.525	4.76	3.81	<0.4			O

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 80° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	CCGT0301005ML-P	4.0	3.5	1.4	1.9	<0.05	O	O		O
	CCGT0301005MR-P	4.0	3.5	1.4	1.9	<0.05	O	O		O
	CCGT030101ML-P	4.0	3.5	1.4	1.9	<0.1	●	O		●
	CCGT030101MR-P	4.0	3.5	1.4	1.9	<0.1	O	O		O
	CCGT030102ML-P	4.0	3.5	1.4	1.9	<0.2	●	O		●
	CCGT030102MR-P	4.0	3.5	1.4	1.9	<0.2		O		O
	CCGT030104ML-P	4.0	3.5	1.4	1.9	<0.4	●	O		●
	CCGT030104MR-P	4.0	3.5	1.4	1.9	<0.4	O	O		O
	CCGT0401005ML-P	4.8	4.3	1.8	2.3	<0.05	O	O		O
	CCGT0401005MR-P	4.8	4.3	1.8	2.3	<0.05	O	O		O
	CCGT040101ML-P	4.8	4.3	1.8	2.3	<0.1	O	O		O
	CCGT040101MR-P	4.8	4.3	1.8	2.3	<0.1	O	O		O
	CCGT040102ML-P	4.8	4.3	1.8	2.3	<0.2		O		●
	CCGT040102MR-P	4.8	4.3	1.8	2.3	<0.2		O		O
	CCGT040104ML-P	4.8	4.3	1.8	2.3	<0.4		O		●
	CCGT040104MR-P	4.8	4.3	1.8	2.3	<0.4		O		O
	CCGT0602005ML-P	6.5	6.35	2.38	2.8	<0.05	O	O		O
	CCGT0602005MR-P	6.5	6.35	2.38	2.8	<0.05	O	●		O
	CCGT060201ML-P	6.5	6.35	2.38	2.8	<0.1	●			●
	CCGT060201MR-P	6.5	6.35	2.38	2.8	<0.1	O	●		O
	CCGT09T3005ML-P	9.7	9.525	3.97	4.4	<0.05	O	O		O
	CCGT09T3005MR-P	9.7	9.525	3.97	4.4	<0.05	O	●		O
	CCGT09T301ML-P	9.7	9.525	3.97	4.4	<0.1	O	O		O
	CCGT09T301MR-P	9.7	9.525	3.97	4.4	<0.1	O	O		O
	CCGT030101L-P	4.0	3.5	1.4	1.9	0.1		●
	CCGT030102L-P	4.0	3.5	1.4	1.9	0.2
	CCGT030104L-P	4.0	3.5	1.4	1.9	0.4
	CCGT040101L-P	4.8	4.3	1.8	2.3	0.1
	CCGT040102L-P	4.8	4.3	1.8	2.3	0.2
	CCGT040104L-P	4.8	4.3	1.8	2.3	0.4		●
	CCGT060201L-P	6.5	6.35	2.38	2.8	0.1		O
	CCGT060201R-P	6.5	6.35	2.38	2.8	0.1		O

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 80° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	CCGT060202L-P	6.5	6.35	2.38	2.8	0.2
	CCGT060202R-P	6.5	6.35	2.38	2.8	0.2
	CCGT060204L-P	6.5	6.35	2.38	2.8	0.4
	CCGT060204R-P	6.5	6.35	2.38	2.8	0.4
			CCGT09T301L-P	9.7	9.525	3.97	4.4	0.1		O
			CCGT09T301L-P	9.7	9.525	3.97	4.4	0.1		O
	CCGT09T301R-P	9.7	9.525	3.97	4.4	0.1		●
	CCGT09T302L-P	9.7	9.525	3.97	4.4	0.2		O
	CCGT09T302R-P	9.7	9.525	3.97	4.4	0.2
	CCGT09T304L-P	9.7	9.525	3.97	4.4	0.4
	CCGT09T304R-P	9.7	9.525	3.97	4.4	0.4
	CCGT0602005ML-G	6.5	6.35	2.38	2.8	<0.05	●	O		O
	CCGT0602005MR-G	6.5	6.35	2.38	2.8	<0.05	O	O		O
	CCGT060201MEL-G	6.5	6.35	2.38	2.8	<0.1	O	O		O
	CCGT060201MER-G	6.5	6.35	2.38	2.8	<0.1	O	O		O
	CCGT060201ML-G	6.5	6.35	2.38	2.8	<0.1		O		O
	CCGT060201MR-G	6.5	6.35	2.38	2.8	<0.1		O		O
	CCGT060202ML-G	6.5	6.35	2.38	2.8	<0.2		O		O
	CCGT060202MR-G	6.5	6.35	2.38	2.8	<0.2		O		O
	CCGT09T3005ML-G	9.7	9.525	3.97	4.4	<0.05		O		O
	CCGT09T3005MR-G	9.7	9.525	3.97	4.4	<0.05	●	●		O
	CCGT09T301MEL-G	9.7	9.525	3.97	4.4	<0.1	O	O		O
	CCGT09T301MER-G	9.7	9.525	3.97	4.4	<0.1	O	O		O
	CCGT09T301ML-G	9.7	9.525	3.97	4.4	<0.1	●	O		O
	CCGT09T301MR-G	9.7	9.525	3.97	4.4	<0.1	●	●		●
	CCGT09T302ML-G	9.7	9.525	3.97	4.4	<0.2		O		O
	CCGT09T302MR-G	9.7	9.525	3.97	4.4	<0.2		O		●

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 80° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	CCGT060201EL-G	6.5	6.35	2.38	2.8	0.1		O
	CCGT060201ER-G	6.5	6.35	2.38	2.8	0.1		O
	CCGT060201L-G	6.5	6.35	2.38	2.8	0.1		O
	CCGT060201R-G	6.5	6.35	2.38	2.8	0.1		O
	CCGT060202EL-G	6.5	6.35	2.38	2.8	0.2
	CCGT060202ER-G	6.5	6.35	2.38	2.8	0.2
	CCGT060202L-G	6.5	6.35	2.38	2.8	0.2
	CCGT060202R-G	6.5	6.35	2.38	2.8	0.2
	CCGT060204EL-G	6.5	6.35	2.38	2.8	0.4
	CCGT060204ER-G	6.5	6.35	2.38	2.8	0.4
	CCGT060204L-G	6.5	6.35	2.38	2.8	0.4		O
	CCGT060204R-G	6.5	6.35	2.38	2.8	0.4		O
	CCGT09T301EL-G	9.7	9.525	3.97	4.4	0.1
	CCGT09T301ER-G	9.7	9.525	3.97	4.4	0.1
	CCGT09T301L-G	9.7	9.525	3.97	4.4	0.1
	CCGT09T301R-G	9.7	9.525	3.97	4.4	0.1
	CCGT09T302EL-G	9.7	9.525	3.97	4.4	0.2
	CCGT09T302ER-G	9.7	9.525	3.97	4.4	0.2
	CCGT09T302L-G	9.7	9.525	3.97	4.4	0.2
	CCGT09T302R-G	9.7	9.525	3.97	4.4	0.2
	CCGT09T304EL-G	9.7	9.525	3.97	4.4	0.4
	CCGT09T304ER-G	9.7	9.525	3.97	4.4	0.4
	CCGT09T304L-G	9.7	9.525	3.97	4.4	0.4
	CCGT09T304R-G	9.7	9.525	3.97	4.4	0.4		O

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 80° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	CCGT0602005M-BF	6.5	6.35	2.38	2.8	<0.05
	CCGT060201M-BF	6.5	6.35	2.38	2.8	<0.1
	CCGT060202M-BF	6.5	6.35	2.38	2.8	<0.2
	CCGT09T301M-BF	9.7	9.525	3.97	4.4	<0.1			O
	CCGT09T302M-BF	9.7	9.525	3.97	4.4	<0.2			O
	CCGT09T304M-BF	9.7	9.525	3.97	4.4	<0.4
	CCGT060201M-BK	6.5	6.35	2.38	2.8	<0.1
	CCGT060201M-BK	6.5	6.35	2.38	2.8	<0.1
	CCGT060202M-BK	6.5	6.35	2.38	2.8	<0.2
	CCGT09T301M-BK	9.7	9.525	3.97	4.4	<0.1			O
	CCGT09T302M-BK	9.7	9.525	3.97	4.4	<0.2			●
	CCGT09T304M-BK	9.7	9.525	3.97 4.4		<0.4

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 55° with Hole

Order No.	Dimensions(mm)					Coated Cemented Carbide
	LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	DCGT0702005ML-P	7.8	6.35	2.38	2.8	<0.05	O			O
	DCGT0702005MR-P	7.8	6.35	2.38	2.8	<0.05	O			O
	DCGT070201ML-P	7.8	6.35	2.38	2.8	<0.1	O	O		O
	DCGT070201MR-P	7.8	6.35	2.38	2.8	<0.1	O			O
	DCGT070202MR-P	7.8	6.35	2.38	2.8	<0.2				O
	DCGT11T3005ML-P	11.6	9.525	3.97	4.4	<0.05	O	O		O
	DCGT11T3005MR-P	11.6	9.525	3.97	4.4	<0.05	O	●		O
	DCGT11T302MR-P	11.6	9.525	3.97	4.4	<0.2	●	O		●
	DCGT0702003L-P	7.8	6.35	2.38	2.8	0.03		O
	DCGT0702003R-P	7.8	6.35	2.38	2.8	0.03		●
	DCGT070201L-P	7.8	6.35	2.38	2.8	0.1		O
	DCGT070201R-P	7.8	6.35	2.38	2.8	0.1
	DCGT070202L-P	7.8	6.35	2.38	2.8	0.2		O
	DCGT070202R-P	7.8	6.35	2.38	2.8	0.2		●
	DCGT070204L-P	7.8	6.35	2.38	2.8	0.4
	DCGT070204R-P	7.8	6.35	2.38	2.8	0.4		O
	DCGT11T3003L-P	11.6	9.525	3.97	4.4	0.03		O
	DCGT11T3003R-P	11.6	9.525	3.97	4.4	0.03		O
	DCGT11T301L-P	11.6	9.525	3.97	4.4	0.1		O
	DCGT11T301R-P	11.6	9.525	3.97	4.4	0.1
	DCGT11T302L-P	11.6	9.525	3.97	4.4	0.2
	DCGT11T302R-P	11.6	9.525	3.97	4.4	0.2
	DCGT11T304L-P	11.6	9.525	3.97	4.4	0.4
	DCGT11T304R-P	11.6	9.525	3.97	4.4	0.4	O

Stock OAvailable Upon Order

Turning Insert (Positive)

Diamond 55° with Hole

Order No.	Dimensions(mm)					Coated Cemented Carbide
	LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	DCGT0702005ML-G	7.8	6.35	2.38	2.8	<0.05	O	O		O
	DCGT0702005MR-G	7.8	6.35	2.38	2.8	<0.05	●	●		O
	DCGT070201MEL-G	7.8	6.35	2.38	2.8	<0.1	O	O		●
	DCGT070201MER-G	7.8	6.35	2.38	2.8	<0.1	O	O		●
	DCGT070201ML-G	7.8	6.35	2.38	2.8	<0.1	O	O		O
	DCGT070201MR-G	7.8	6.35	2.38	2.8	<0.1	●	O		O
	DCGT11T3005ML-G	11.6	9.525	3.97	4.4	<0.05	O	O		O
	DCGT11T3005MR-G	11.6	9.525	3.97	4.4	<0.05	O	●		●
	DCGT11T301MEL-G	11.6	9.525	3.97	4.4	<0.1	O	O		O
	DCGT11T301MER-G	11.6	9.525	3.97	4.4	<0.1	O	O		O
	DCGT11T301ML-G	11.6	9.525	3.97	4.4	<0.1	O	O		O
	DCGT11T301MR-G	11.6	9.525	3.97	4.4	<0.1	●	●		●
	DCGT11T302MER-G	11.6	9.525	3.97	4.4	<0.2
	DCGT11T302MR-G	11.6	9.525	3.97	4.4	<0.2		O
	DCGT070201L-G	7.8	6.35	2.38	2.8	0.1		O
	DCGT070201R-G	7.8	6.35	2.38	2.8	0.1		●
	DCGT070202L-G	7.8	6.35	2.38	2.8	0.2		O
	DCGT070202R-G	7.8	6.35	2.38	2.8	0.2		●
	DCGT11T301EL-G	11.6	9.525	3.97	4.4	0.1
	DCGT11T301ER-G	11.6	9.525	3.97	4.4	0.1
	DCGT11T301L-G	11.6	9.525	3.97	4.4	0.1
	DCGT11T301R-G	11.6	9.525	3.97	4.4	0.1
	DCGT11T302EL-G	11.6	9.525	3.97	4.4	0.2
	DCGT11T302ER-G	11.6	9.525	3.97	4.4	0.2
	DCGT11T302L-G	11.6	9.525	3.97	4.4	0.2
	DCGT11T302R-G	11.6	9.525	3.97	4.4	0.2
	DCGT11T304EL-G	11.6	9.525	3.97	4.4	0.4		O
	DCGT11T304ER-G	11.6	9.525	3.97	4.4	0.4		●
	DCGT11T302MR-S	11.6	9.525	3.97	4.4	<0.2	●			●
	DCGT11T304MR-S	11.6	9.525	3.97	4.4	<0.4	●

Turning Insert (Positive)

Diamond 55° with Hole

Order No.		Dimensions(mm)					Coated Cemented Carbide
Order No.		LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
	DCGT070201M-AF	7.8	6.35	2.38	2.8	<0.1
	DCGT11T301M-AF	11.6	9.525	3.97	4.4	<0.1			O


	DCGT11T301M-AK	11.6	9.525	3.97	4.4	<0.1			O
	DCGT11T302M-AK	11.6	9.525	3.97	4.4	<0.2			O
	DCGT11T304M-AK	11.6	9.525	3.97	4.4	<0.4				O

D	DCGT070201M-BF	7.8	6.35	2.38	2.8	<0.1			O
	DCGT070202M-BF	7.8	6.35	2.38	2.8	<0.2
	CGT070204M-BF	7.8	6.35	2.38	2.8	<0.4
	DCGT11T301M-BF	11.6	9.525	3.97	4.4	<0.1			O
	DCGT11T302M-BF	11.6	9.525	3.97	4.4	<0.2
	DCGT11T304M-BF	11.6	9.525	3.97	4.4	<0.4
D	DCGT070201M-BK	7.8	6.35	2.38	2.8	<0.1			O
	CGT070202M-BK	7.8	6.35	2.38	2.8	<0.2
	DCGT11T301M-BK	11.6	9.525	3.97	4.4	<0.1			O
	DCGT11T302M-BK	11.6	9.525	3.97	4.4	<0.2
	DCGT11T304M-BK	11.6	9.525	3.97	4.4	<0.4
	DCGT11T301M-SK	11.6	9.525	3.97	4.4	<0.1	O
	DCGT11T302M-SK	11.6	9.525	3.97	4.4	<0.2	O
	DCGT11T304M-SK	11.6	9.525	3.97	4.4	<0.4	O

	DCGT11T301M-MM	11.6	9.525	3.97	4.4	<0.1
	DCGT11T302M-MM	11.6	9.525	3.97	4.4	<0.2
	DCGT11T304M-MM	11.6	9.525	3.97	4.4	<0.4

●Stock OAvailable Upon Order

Turning Insert (Positive)

Triangle 60° with Hole

Order No.	Dimensions(mm)					Coated Cemented Carbide
Order No.	LE	IC	S	D1	RE	GAT7115	GAT7120	GAT7120A	GAT7125
TBGT060102L-PTBGT060104L-P	6.9	3.97	1.59	2.3	0.2
	6.9	3.97	1.59	2.3	0.4

Stock OAvailable Upon Order

Turning Insert (Positive)

Recommended Cutting Data (Negative Inserts)

Recommended Cutting Data (Positive Inserts)

MEMO

SMALL PART TURNING TOOLS

List of Small Part Turning Inserts Small Part Turning Inserts (Negative)

List of Small Part Turning Inserts

Small Part Turning Inserts (Positive)

List of Small Part Turning Inserts

Small Part Turning Inserts (Positive)

List of Small Part Turning Inserts

Small Part Turning Inserts (Positive)

List of Small Part Turning Inserts Small Part Turning Inserts (Positive)

List of Small Part Turning Inserts Small Part Turning Inserts (Other)

Schematic Diagram of Small Part Tool Machining

Turning Insert (Positive)

快速跳转到指定页