该页无缩略图
丝锥柄部方头尺寸
| ISO | JIS | DIN | |||||||||
| 柄部尺寸 | 丝锥型号 | 柄部尺寸 | 丝锥型号 | 柄部尺寸 | 丝锥型号 | ||||||
| d | a | ISO529(1) | ISO2298 | DCON B | LPR | JISB4430(3) | DCON | B | LPR | DIN376 DIN371(4) DIN374(5) | |
| 2.24 | 1.80 | 4 | M3.0 | 3.00 | 2.50 5 | M1.0-M2.6 | 2.50 | 2.10 | 5 | M1-M1.8 M3.5 | |
| 2.50 | 2.00 4 | M1-M2 | M3.5 | 4.00 | 3.20 6 | M3.0-M3.5 | 2.80 | 2.10 | 5 M2-M2.5 | M4.0 | |
| 2.80 | 2.24 5 | M2.2-M2.6 | 5.00 | 4.00 7 | M4.0-M4.5 | 3.50 | 2.70 | 6 m3 | M4.5-M5 | ||
| 3.15 | 2.50 5 | M3.0 | M4.0 | 5.50 | 4.50 7 | M5.0 | 4.00 | 3.00 | 6 M3.5 | ||
| 3.55 | 2.80 5 | M3.5 | M4.5 | 6.00 | 4.50 7 | M6.0 | 4.50 | 3.40 | 6 M4.0 | M6.0 | |
| 4.00 | 3.15 6 | M4.0 | M5.0 | 6.20 | 5.00 8 | M7.0-M8.0 | 6.00 | 4.90 | 8 M4.5-M6 | M8.0 | |
| 4.50 | 3.55 6 | M4.5 | M6.0 | 7.00 | 5.50 8 | M9.0-M10 | 7.00 | 5.50 | 8 M7.0 | M10 | |
| 5.00 | 4.00 7 | M5.0 | 8.00 | 6.00 9 | M11 | 8.00 | 6.20 | 9 M8.0 | |||
| 5.60 | 4.50 7 | M7.0 | 8.50 | 6.50 9 | M12 | 9.00 | 7.00 | 10 | M12 | ||
| 6.30 | 5.00 8 | M6.0 | M8.0 | 9.50 | 7.00 10 | M10-M11 | 10.00 | 8.00 | 11 M10.0 | ||
| 7.10 | 5.60 8 | M7.0 | M9.0 | 10.5 | 8.00 11 | M14 | 11.00 | 9.00 | 12 | M14 | |
| 8.00 | 6.30 9 | M8.0 | M10-M11 | 12.50 | 10.00 13 | M16 | 12.00 | 9.00 | 12 | M16 | |
| 9.00 | 7.10 10 | m9.0 | M12 | 14.00 | 11.00 14 | M18 | 14.00 | 11.00 | 14 | M18 | |
| 10.00 | 8.00 11 | M10 | 15.00 | 12.00 15 | M20 | 16.00 | 12.00 | 15 | M20 | ||
| 11.20 | 9.00 12 | M13-M15 | 17.00 | 13.00 16 | M22 | 18.00 | 14.50 | 17 | M22-M26 | ||
| 12.50 | 10.00 13 | M16-M17 | 19.00 | 15.00 18 | M24 | 20.00 | 16.00 | 19 | M27 | ||
| 14.00 | 11.20 14 | M18-M21 | 20.00 | 15.00 18 | M27 | 22.00 | 18.00 | 21 | M29-M32 | ||
| 16.00 | 12.50 16 | M22-M23 | 23.00 | 17.00 20 | M30 | 25.00 | 20.00 | 23 | M33 | ||
| 18.00 | 14.00 18 | M24-M26 | 25.00 | 19.00 22 | M33 | 28.00 | 22.00 | 25 | M34-M38 | ||
| 20.00 | 16.00 20 | M27-M30 | 28.00 | 21.00 24 | M36 | 32.00 | 24.00 | 27 | M39-M42 | ||
| 22.40 | 18.00 | 22 | M31-M33 | 30.00 | 23.00 26 | M39 | 36.00 | 29.00 | 32 | M44-M50 | |
| 25.00 | 20.00 | 24 | M36 | 32.00 | 26.00 30 | M42 | 40.00 | 32.00 | 35 | M52 | |
| 28.00 | 22.40 | 26 | M37-M42 | 45.00 | 35.00 | 38 | M55-M60 | ||||
| 31.50 | 25.00 | 28 | M44-M50 | ||||||||
| 35.50 | 28.00 | 31 | M52-M56 | ||||||||
| 40.00 | 31.50 | 34 | M58-M65 | ||||||||
| 45.00 | 35.50 | 38 | M66-M75 | ||||||||
注： (1)(4)为粗柄普通粗牙螺纹丝锥(2)(5)为细柄普通粗牙螺纹丝锥(3)为等径普通粗牙螺纹丝锥
附件Accessories
拉钉 -G3 Pull Studs
ER卡簧 -G6 ERCollets
液压卡簧 -G10 HydraulicCollets
直筒卡簧 -G12 Straight Collets
测试棒· -G13 TestBars
ER螺母 .G15 ERNuts
止水垫圈，三面刃铣刀刀柄用垫圈 G17 SealingDiskWashersForSlottingCutterHolder
HSK冷却液套管及扳手 -G18 HSKCoolantTubesAndCoolantTubeWrenches
卸刀夹具，清洁毛刷 G19 ToolingSetupFixtures,Cleaning brushes
可换杆定扭矩扳手 G20 Torquescrewdriver
星形可换扳手杆 G20 Interchangeableblade.Fortorquescrewdrivers.
拉钉扳手 -G22 Pull Nail Wrench
ER螺母扳手· G23 ERNuts Wrench
拉钉 (ISO 7388/2) Pull Studs
ISO7388/2A型 ISO 7388/2Type A
| ！ | 型号 Model | 库存 Stock | 尺寸Size（mm) | |||||||||
| LB | LB2 | LB3 | BD1 | BD2 | BD3 | CRKS | CND | |||||
| 30 | LDA30 | 44 | 24 | 19 | 17 | 12 | 8 | M12 | BD4 13 | - | ||
| 40 | LDA40 | 54 | 26 | 20 | 5 7 | 23 | 19 | 14 | M16 | 17 | 7.0 | |
| 50 | LDA50 | 。 | 74 | 34 | 25 | 10 | 36 | 28 | 21 | M24 | 25 | 11.5 |
| 60 | LDA60 | O | 93 | 44.2 | 33.2 | 13 | 60 | 38 | 28 | M30 | 35 | 14 |
●标准库存订单生产
ISO7388/2B型 ISO7388/2Type B 拉钉 (DIN 69872) Pull Studs
| 型号 Model | 库存K | 尺寸Size(mm) | ||||||||||
| OAL | LB | LB2 | LB3 | BD1 | BD2 | BD3 | CRKS | BDA | CND | |||
| 30 | LDB30 | 。 | 31.8 | 11.8 | 8.1 | 5 | 16.5 | 13.3 | 9.3 | M12 | 13 | - |
| 40 | LDB40 | 。 | 44.5 | 16.4 | 11.15 | 7 | 22.5 | 18.95 | 12.95 | M16 | 17 | 7.0 |
| 50 | LDB50 | 65.5 | 25.55 | 17.95 | 10 | 36 | 29.1 | 19.6 | M24 | 25 | 11.5 | |
| 60 | LDB60 | 88 | 38.15 | 27.65 | 12.85 | 50 | 37.25 | 24.95 | M30 | 32 | 14 | |
| ！ | 型号 Model | 库存 Stock | 尺寸Size（mm) | |||||||||
| LB | LB2 | LB3 | BD1 | BD2 | BD3 | CRKS | BD4 CND | |||||
| 30 | D30 | 0 | 44 | 24 | 19 | 17 | 13 | 9 | M12 | 13 | - | |
| 40 | D40 | 0 | 54 | 26 | 20 | 5 7 | 23 | 19 | 14 | M16 | 17 | 7.0 |
| 50 | D50 | 74 | 34 | 25 | 10 | 36 | 28 | 21 | M24 | 25 | 11.5 | |
| 60 | D60 | O | 90 | 40 | 30 | 12 | 52 | 40 | 30 | M30 | 32 | 14 |
拉钉 (ANSI B5.50) Pull Studs
| 型号 Model | 库存 | 尺寸Size(mm) | ||||||||||
| OAL | LB | LB2 | LB3 | BD1 | BD2 | BD3 | CRKS | CND | ||||
| 30 | A30 | 27.94 | 11.684 | 8.128 | 2.54 | 16.51 | 13.208 | 9.779 | 1/2-13UNC | 4.75 | ||
| 40 | A40 | 。 | 38.1 | 16.256 | 11.176 | 3.048 | 23.876 | 18.796 | 12.446 | 5/8-11UNC | 7.14 | |
| 50 | A50 | 58.42 | 25.4 | 17.78 | 5.08 | 36.576 | 28.956 | 20.828 | 1-8UNC | 11.89 | ||
拉钉 (MAS403) Pull Studs
| ！ | 型号 | 库存 | |||||||||||
| LB, | LB2 | LB3 | CRKS | BD4 | BHTA2 | CND | |||||||
| 30 | P30T-I | 00 | OAL 43 | ||||||||||
| 30 | P30T-II | 2323 | 18 18 | 4.5 4.5 | 16.5 16.5 | 11 11 | 7 7 | M12 M12 | 12.5 12.5 | 45° 30° | - | ||
| 43 | - | ||||||||||||
| 40 | P40T-I | 35 | 28 | 10 | M16 | 17 | 45° | 4.0 | |||||
| 40 | P40T-II | 60 60 | 35 | 28 | 6 6 | 23 | 15 | M16 | 17 | 30° | 4.0 | ||
| 40 | 8 | 60 | 23 | 15 | 10 | 4.0 | |||||||
| P40T-III | 35 | 28 | 6 | 23 | 15 | 10 | M16 | 17 | 0° | ||||
| 50 | P50T-I | 45 | 35 | 10 | 17 | M24 | 25 | 45° | 6.0 | ||||
| 50 | P50T-II | 85 | 45 | 35 | 10 | 38 | 23 | 17 | M24 | 25 | 30° | 6.0 | |
| 50 | P50T-II | 85 85 | 45 | 35 | 10 | 38 38 | 23 23 | 17 | M24 | 25 | 0° | 6.0 | |
| 60 | P60T-I | 115 | 65 | 53 | 14 | 56 | 32 | 24 | M30 | 31 | 45° | 12.0 | |
| 60 | P60T-II | 8 | 115 | 65 | 53 | 14 | 56 | 32 | 24 | M30 | 31 | 30° | 12.0 |
| 60 | P60T-III | 115 | 65 | 53 | 14 | 56 | 32 | 24 | M30 | 31 | 0° | 12.0 | |
^ * 常规制造不带冷却孔，若需要冷却孔，订货时说明。
MAZAK/BT拉钉 MAZAK/BTPull Studs
| 型号 Model | 库存 Stock | 尺寸Size（mm) | ||||||||||
| OAL | LB, | LB2 | LB3 | BD | BD2 | BD3 | CRKS | BD4 | CND | |||
| 40 | MAZAK/BT40 | 44.1 | 19.1 | 14.02 | 5 | 22 | 18.8 | 12.45 | M16 | 17 | 7.0 | |
| 50 | MAZAK/BT50 | 。 | 65.2 | 25.2 | 17.58 | 8 | 37 | 28.96 | 20.83 | M24 | 25 | 10 |
ER卡簧 (DIN 6499) ER Collets
-精度按DIN6499标准执行。
-刀具夹持小于23卡簧内孔长度将造成卡簧永久性损坏。
-夹持等于卡簧内孔长度可获得最好的夹持精度和夹持力。
-被夹持的刀具直径不得大于卡簧最大夹持直径。
-卡簧夹持范围：ER11为 0 . 5mm ，ER16及以上为1.0mm。
| 卡簧Collets 范围 | ER11 | ER16 | ER20 | ER25 | ER32 | ER40 OAL/BD,(mm) | 卡簧Collets | |
| OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | 夹持范围 | |||
| (mm) | 18.5/11.5 | 27.5/17.0 | 31.5/21.0 | 34.0/26.0 | 40.0/33.0 | 46.0/41.0 | （mm） | |
| 2.5-2.0 | 8 | ER11-2.5 | 2.5-2.0 | |||||
| 3.0-2.5 | 8 | ER11-3 | ER16-3 | ER20-3 | ER25-3 | ER32-3 | 3.0-2.5 | |
| 3.5-3.0 | ER11-3.5 | 3.5-3.0 | ||||||
| 4.0-3.5 | ER11-4 | ER16-4 | ER20-4 | ER25-4 | ER32-4 | ER40-4 | 4.0-3.5 | |
| 4.5-4.0 | ER11-4.5 | 4.5-4.0 | ||||||
| 5.0-4.5 | 0 | ER11-5 | ER16-5 | ER20-5 | ER25-5 | ER32-5 | ER40-5 | 5.0-4.5 |
| 5.5-5.0 | 0 | ER11-5.5 | 5.5-5.0 | |||||
| 6.0-5.5 | 0 | ER11-6 | ER16-6 | ER20-6 | ER25-6 | ER32-6 | ER40-6 | 6.0-5.5 |
| 6.5-6.0 | ER11-6.5 | 6.5-6.0 | ||||||
| 7.0-6.5 | ER11-7 | 7.0-6.5 | ||||||
| 7.0-6.0 | 0 | ER16-7 | ER20-7 | ER25-7 | ER32-7 | ER40-7 | 7.0-6.0 | |
| 8.0-7.0 | ER16-8 | ER20-8 | ER25-8 | ER32-8 | ER40-8 | 8.0-7.0 | ||
| 9.0-8.0 | 0 | ER16-9 | ER20-9 | ER25-9 | ER32-9 | ER40-9 | 9.0-8.0 | |
| 10.0-9.0 | 0 0 | ER16-10 | ER20-10 | ER25-10 | ER32-10 | ER40-10 | 10.0-9.0 | |
| 11.0-10.0 | ER20-11 | ER25-11 | ER32-11 | ER40-11 | 11.0-10.0 | |||
| 12.0-11.0 | ER20-12 | ER25-12 | ER32-12 | ER40-12 | 12.0-11.0 | |||
| 13.0-12.0 | ER20-13 | ER25-13 | ER32-13 | ER40-13 | 13.0-12.0 | |||
| 14.0-13.0 | ER25-14 | ER32-14 | ER40-14 ER40-15 | 14.0-13.0 | ||||
| 15.0-14.0 | 0 | ER25-15 ER25-16 | ER32-15 | ER40-16 | 15.0-14.0 | |||
| 16.0-15.0 | 0 | ER32-16 ER32-17 | ER40-17 | 16.0-15.0 | ||||
| 17.0-16.0 | ER40-18 | 17.0-16.0 | ||||||
| 18.0-17.0 | 0 | ER32-18 | ER40-19 | 18.0-17.0 | ||||
| 19.0-18.0 | ER32-19 | 19.0-18.0 | ||||||
| 20.0-19.0 | ER32-20 | ER40-20 | 20.0-19.0 | |||||
| 21.0-20.0 | 8 | ER40-21 | 21.0-20.0 | |||||
| 22.0-21.0 | ER40-22 ER40-23 | 22.0-21.0 | ||||||
| 23.0-22.0 | ER40-24 | 23.0-22.0 | ||||||
| 24.0-23.0 | 8 | ER40-25 | 24.0-23.0 25.0-24.0 | |||||
| 25.0-24.0 26.0-25.0 | ER40-26 | 26.0-25.0 |
●标准库存订单生产
ER卡簧 (DIN 6499) ER Collets
-为保证卡簧精度，推荐夹持定径刀具。
-刀具夹持小于2/3卡簧内孔长度将造成卡簧永久性损坏。
-夹持等于卡簧内孔长度可获得最好的夹持精度和夹持力。
-被夹持的刀具直径不得大于卡簧最大夹持直径。
-卡簧夹持范围：ER11为 0 . 5mm ，ER16及以上为 1 . 0 {mm } _ { \circ }
| 卡簧Collets DCONWS 夹持范围 | ER11 | ER16 | ER20 | ER25 | ER32 | ER40 | 卡簧Collets dm | |
| OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | 夹持范围 | ||
| (mm) | 18.5/11.5 | 27.5/17.0 | 31.5/21.0 | 34.0/26.0 | 40.0/33.0 | 46.0/41.0 | （mm) | |
| 2.5-2.0 | OOQ | ER11-2.5A | 2.5-2.0 | |||||
| 3.0-2.5 | ER11-3A | ER16-3A | ER20-3A | ER25-3A | ER32-3A | 3.0-2.5 | ||
| 3.5-3.0 | ER11-3.5A | 3.5-3.0 | ||||||
| 4.0-3.5 | ER11-4A | ER16-4A | ER20-4A | ER25-4A | ER32-4A | ER40-4A | 4.0-3.5 | |
| 4.5-4.0 | 8 | ER11-4.5A | 4.5-4.0 | |||||
| 5.0-4.5 | ER11-5A | ER16-5A | ER20-5A | ER25-5A | ER32-5A | ER40-5A | 5.0-4.5 | |
| 5.5-5.0 | ER11-5.5A | 5.5-5.0 | ||||||
| 6.0-5.5 | 8 | ER11-6A | ER16-6A | ER20-6A | ER25-6A | ER32-6A | ER40-6A | 6.0-5.5 |
| 6.5-6.0 | 8 | ER11-6.5A | 6.5-6.0 | |||||
| 7.0-6.5 | 8 | ER11-7A | 7.0-6.5 | |||||
| 7.0-6.0 | ER16-7A | ER20-7A | ER25-7A | ER32-7A | ER40-7A | 7.0-6.0 | ||
| 8.0-7.0 | ER16-8A | ER20-8A | ER25-8A | ER32-8A | ER40-8A | 8.0-7.0 | ||
| 9.0-8.0 10.0-9.0 | 8 | ER16-9A ER16-10A | ER20-9A ER20-10A | ER25-9A | ER32-9A | ER40-9A | 9.0-8.0 | |
| 11.0-10.0 | ER20-11A | ER25-10A | ER32-10A | ER40-10A | 10.0-9.0 | |||
| 12.0-11.0 | ER20-12A | ER25-11A | ER32-11A | ER40-11A | 11.0-10.0 | |||
| 13.0-12.0 | ER20-13A | ER25-12A | ER32-12A | ER40-12A | 12.0-11.0 | |||
| 14.0-13.0 | 8 | ER25-13A ER25-14A | ER32-13A | ER40-13A ER40-14A | 13.0-12.0 | |||
| 15.0-14.0 | 8 | ER25-15A | ER32-14A | ER40-15A | 14.0-13.0 | |||
| 16.0-15.0 | 8 | ER25-16A | ER32-15A | ER40-16A | 15.0-14.0 | |||
| 17.0-16.0 | ER32-16A | 16.0-15.0 | ||||||
| 18.0-17.0 | 8 | ER32-17A | ER40-17A | 17.0-16.0 | ||||
| 8 | ER32-18A | ER40-18A | 18.0-17.0 | |||||
| 19.0-18.0 | 8 | ER32-19A | ER40-19A | 19.0-18.0 | ||||
| 20.0-19.0 | ER32-20A | ER40-20A | 20.0-19.0 | |||||
| 21.0-20.0 | ER40-21A | 21.0-20.0 | ||||||
| 22.0-21.0 | ER40-22A | 22.0-21.0 | ||||||
| 23.0-22.0 | 0 | ER40-23A | 23.0-22.0 | |||||
| 24.0-23.0 | ER40-24A | 24.0-23.0 | ||||||
| 25.0-24.0 | 8 | ER40-25A | 25.0-24.0 | |||||
| 26.0-25.0 | ER40-26A | 26.0-25.0 |
●标准库存订单生产
ER止水卡簧 (DIN6499) ER Coolant Collets
-为保证良好的止水功能，推荐采用定径夹持。
-夹持柄径长度必须大于等于卡簧内孔长度才能实现止水功能。
-被夹持的刀具直径不得大于卡簧最大夹持直径。
| 卡簧Collets 持范围 | ER11 | ER16 | ER20 | ER25 | ER32 | ER40 | 卡簧Collets |
| OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | OAL/BD,(mm) | ||
| (mm) | 18.5/11.5 | 27.5/17.0 | 31.5/21.0 | 34.0/26.0 | 40.0/33.0 | 46.0/41.0 | 夹持范围 (mm) |
| 3.0 | ER11-3C | 3.0 | |||||
| 3.5 | ER11-3.5C | 3.5 | |||||
| 4.0 | ER11-4C | 4.0 | |||||
| 4.5 | ER11-4.5C | 4.5 | |||||
| 5.0 | ER11-5C | ER16-5C | 5.0 | ||||
| 5.5 | ER11-5.5C | 5.5 | |||||
| 6.0 | ER11-6C | ER16-6C | 6.0 | ||||
| 6.5 | ER11-6.5C | 6.5 | |||||
| 7.0 | ER11-7C | ER16-7C | ER20-7C | 7.0 | |||
| 8.0 | ER16-8C | ER20-8C | ER25-8C | ER32-8C | 8.0 | ||
| 9.0 | ER16-9C | ER20-9C | ER25-9C | ER32-9C | 9.0 | ||
| 10.0 | ER16-10C | ER20-10C | ER25-10C | ER32-10C | ER40-10C | 10.0 | |
| 11.0 | ER20-11C | ER25-11C | ER32-11C | ER40-11C | 11.0 | ||
| 12.0 | ER20-12C | ER25-12C | ER32-12C | ER40-12C | 12.0 | ||
| 13.0 | ER20-13C | ER25-13C | ER32-13C | ER40-13C | 13.0 | ||
| 14.0 | ER25-14C | ER32-14C | ER40-14C | 14.0 | |||
| 15.0 | ER25-15C | ER32-15C | ER40-15C | 15.0 | |||
| 16.0 | ER25-16C | ER32-16C | ER40-16C | 16.0 | |||
| 17.0 | ER32-17C | ER40-17C | 17.0 | ||||
| 18.0 | ER32-18C | ER40-18C | 18.0 | ||||
| 19.0 | ER32-19C | ER40-19C | 19.0 | ||||
| 20.0 | ER32-20C | ER40-20C | 20.0 | ||||
| 21.0 | ER40-21C | 21.0 | |||||
| 22.0 | ER40-22C | 22.0 | |||||
| 23.0 | ER40-23C | 23.0 | |||||
| 24.0 | ER40-24C | 24.0 | |||||
| 25.0 | ER40-25C | 25.0 | |||||
| 26.0 | ER40-26C | 26.0 |
\*若需要其他尺寸规格的卡簧，请与本公司咨询、订购。
ER攻丝卡簧 ERRigidTapCollets
-请确保所用丝锥柄径与卡簧内方尺寸一致。
-被夹持的刀具直径不得大于卡簧最大夹持直径。
-丝锥方柄必须插入卡簧方孔内，方能进行加工。
| 型号 | 库存 | ISO529/ISO2283 | DIN374/DIN376 | JISB4430 | |
| ER20-6.3B5 | ER32-6.3B5 | M8 | M8 | M6/M8 | |
| ER20-7B5.5 | ER32-7B5.5 | 8 | M10 | M10 | |
| ER20-8B6.3 | ER32-8B6.3 | 8 | M10 | ||
| ER20-8.5B6.5 | ER32-8.5B6.5 | 8 | M12 | ||
| ER20-9B7.1 | ER32-9B7.1 | M12 | M12 | ||
| ER32-12B9 | M16 | ||||
| ER32-12.5B10 | 8 | M16 | M16 | ||
| ER32-14B11.2 | 8 | M18/M20 | M18 | M18 M20 | |
| ER32-15B12 ER32-16B12 | 8 | M20 | |||
●标准库存订单生产
攻丝卡簧应用指南
1）丝锥方柄必须伸入卡簧方槽内，才能安全，有效的工作；
2）选用卡簧时，请注意丝锥的四方柄与卡簧内四方的匹配；
3）卡簧规格型号即包含了配用丝锥柄径及内方孔尺寸，请注意辨别；
液压卡簧 Hydraulic Collets
精度Precision 5um
-切削刀具必须为圆柱形柄，在使用内冷时，必须有一个通孔。
-切削刀具必须完全接触长度为LSC的液压卡簧型腔，否则会对液压卡簧及刀柄产生永久性的损伤。
-液压卡簧必须完全插入到液压柄孔径中，直至肩部与液压柄前端面贴合。
-切削刀具的柄径公差等级为h6。
| 型号 Model | 库存 Stock | 尺寸Size（mm) | |||
| DCONWS | DCONMS | LSC | OAL | ||
| 12 | 16.5 | 47.5 | |||
| HC12-3 HC12-4 | 3 4 | 12 | 16.5 | 47.5 | |
| HC12-5 | 5 | 12 | 16.5 | 47.5 | |
| HC12-6 | 6 | 12 | 24.0 | 47.5 | |
| HC12-8 | 8 | 12 | 25.5 | 47.5 | |
| HC20-3 | 3 | 20 | 17.5 | 52.5 | |
| HC20-4 | 4 | 20 | 17.5 | 52.5 | |
| HC20-5 | · | 5 | 20 | 17.5 | 52.5 |
| HC20-6 | 6 | 20 | 25.5 | 52.5 | |
| HC20-7 | 7 | 20 | 28.0 | 52.5 | |
| HC20-8 | 8 | 20 | 28.0 | 52.5 | |
| HC20-9 | 9 | 20 | 32.5 | 52.5 | |
| HC20-10 | 10 | 20 | 32.5 | 52.5 | |
| HC20-11 | 11 | 20 | 36.0 | 52.5 | |
| HC20-12 | 12 | 20 | 36.0 | 52.5 | |
| HC20-13 | 13 | 20 | 36.5 | 52.5 | |
| HC20-14 | 14 | 20 | 37.0 | 52.5 | |
| HC20-15 | 15 | 20 | 37.0 | 52.5 | |
| HC20-16 | 16 | 20 | 37.5 | 52.5 | |
| HC20-18 | 18 | 20 | 37.5 | 52.5 | |
| HC32-6 | 6 | 32 | 25.5 | 63.5 | |
| HC32-8 | 8 | 32 | 27.5 | 63.5 | |
| HC32-10 | 10 | 32 | 30.5 | 63.5 | |
| HC32-12 | 12 | 32 | 30.5 | 63.5 | |
| HC32-14 | 14 | 32 | 32.5 | 63.5 | |
| HC32-16 | 16 | 32 | 40.5 | 63.5 | |
| HC32-18 | 18 | 32 | 40.5 | 63.5 | |
| HC32-20 | ： | 20 | 32 | 40.5 | 63.5 |
| HC32-25 | 25 | 32 | 48.5 | 63.5 | |
●标准库存订单生产
液压卡簧 Hydraulic Collets
精度Precision 3um
-切削刀具必须为圆柱形柄，在使用内冷时，必须有一个通孔。
-切削刀具必须完全接触长度为LSC的液压卡簧型腔，否则会对液压卡簧及刀柄产生永久性的损伤。
-液压卡簧必须完全插入到液压柄孔径中，直至肩部与液压柄前端面贴合。
-切削刀具的柄径公差等级为h6。
| 型号 Model | 库存 Stock | 尺寸Size（mm) | |||
| DCONWS | DCONMS | LSC | OAL | ||
| HC12-3M | 12 | 16.5 | 47.5 | ||
| 3 4 | 12 | 16.5 | 47.5 | ||
| HC12-4M HC12-5M | 5 | 12 | 16.5 | 47.5 | |
| HC12-6M | 6 | 12 | 24.0 | 47.5 | |
| HC12-8M | ： | 8 | 12 | 25.5 | 47.5 |
| HC20-3M | 3 | 20 | 17.5 | 52.5 | |
| HC20-4M | 4 | 20 | 17.5 | 52.5 | |
| HC20-5M | 5 | 20 | 17.5 | 52.5 | |
| HC20-6M | 6 | 20 | 25.5 | 52.5 | |
| HC20-7M | 7 | 20 | 28.0 | 52.5 | |
| HC20-8M | 8 | 20 | 28.0 | 52.5 | |
| HC20-9M | 9 | 20 | 32.5 | 52.5 | |
| HC20-10M | 10 | 20 | 32.5 | 52.5 | |
| HC20-11M | 11 | 20 | 36.0 | 52.5 | |
| HC20-12M | 12 | 20 | 36.0 | 52.5 | |
| HC20-13M | 13 | 20 | 36.5 | 52.5 | |
| HC20-14M | 14 | 20 | 37.0 | 52.5 | |
| HC20-15M | 15 | 20 | 37.0 | 52.5 | |
| HC20-16M | 16 | 20 | 37.5 | 52.5 | |
| HC32-6M | 6 | 32 | 25.5 | 63.5 | |
| HC32-8M | 8 | 32 | 27.5 | 63.5 | |
| HC32-10M | 10 | 32 | 30.5 | 63.5 | |
| HC32-12M | 12 | 32 | 30.5 | 63.5 | |
| HC32-14M | 14 | 32 | 32.5 | 63.5 | |
| HC32-16M | 16 | 32 | 40.5 | 63.5 | |
| HC32-18M | 18 | 32 | 40.5 | 63.5 | |
| HC32-20M | 20 | 32 | 40.5 | 63.5 | |
| HC32-25M | ： | 25 | 32 | 48.5 | 63.5 |
\*建议配合JT50-HCM..-110M（E62页）产品使用。
●标准库存订单生产
●标准库存订单生产
直筒卡簧 Straight Collets 精度Precision 0.01mm
-适用于强力夹头刀柄。
-夹持柄径公差为h6。
| 卡簧Collets 范围 | C20 | C25 | C32 | C42 | 卡簧Collets 夹持范围 |
| OAL/DCONMs(mm) | OAL/DCONMS(mm) | OAL/DCONMs(mm) | OAL/DCONMs(mm) | ||
| (mm) | 55/20 | 60/25 | 65/32 | 70/42 | (mm) |
| 34 | 34 | ||||
| C20-4 | C25-4 | ||||
| 5 | C20-5 | C25-5 | 5 | ||
| 6 | C20-6 | C25-6 | C32-6 | C42-6 | 6 |
| 8 | C20-8 | C25-8 | C32-8 | C42-8 | 8 |
| 10 | C20-10 | C25-10 | C32-10 | C42-10 | 10 |
| 12 | C20-12 | C25-12 | C32-12 | C42-12 | 12 |
| 14 | C20-14 | C25-14 | C32-14 | C42-14 | 14 |
| 16 | C20-16 | C25-16 | C32-16 | C42-16 | 16 |
| 18 | C25-18 | C32-18 | C42-18 | 18 | |
| 20 | C25-20 | C32-20 | C42-20 | 20 | |
| 25 | C32-25 | C42-25 | 25 | ||
| 32 | C42-32 | 32 | |||
| 库存 | 。 | - |
●标准库存 订单生产
7:24测试棒 7:24 Test Bars
| 型号 Model | 库存 Stock | 尺寸Size | ||||
| DCONMS | (mm) BD1 | LF | LUX | |||
| BT30-TB30-300 | 30 | 31.75 | 30 | 300 | 265 | |
| BT40-TB40-300 | 40 | 44.45 | 40 | 300 | 265 | |
| BT50-TB50-350 | · | 50 | 69.85 | 50 | 350 | 300 |
| JT40-TB40-300 | 0 | 40 | 44.45 | 40 | 300 | 265 |
| JT50-TB50-350 | 50 | 69.85 | 50 | 350 | 300 | |
●标准库存订单生产
HSK测试棒
●标准库存订单生产
液压刀柄测试棒 HydraulicPressureTestBar
| 型号 | 库存 Stock | 尺寸Size(mm) | ||
| Model | DCONMS | OAL | LUX | |
| HC06-TB | 6 | 70 | 40 | |
| HC08-TB | 8 | 70 | 40 | |
| HC10-TB | 10 | 75 | 45 | |
| HC12-TB | 0 | 12 | 80 | 50 |
| HC14-TB | 8 | 14 | 90 | 55 |
| HC16-TB | 0 | 16 | 90 | 55 |
| HC20-TB | 20 | 90 | 55 | |
| HC25-TB | 8 | 25 | 90 | 55 |
| HC32-TB | 32 | 90 | 55 | |
\*使用时，将测试棒插入刀柄内，直至底端，将液压刀柄施压螺钉拧紧，若手能拧动测试棒，则表明液压刀柄已失压，需与厂家联系维修。
●标准库存 订单生产
●标准库存 订单生产
ER螺母B型 ER Nuts B
| 型号 Model | 尺寸Size（mm) | W手ch | 描述 Description | ||
| BD | FTDZ | LF | |||
| CN25B | YER25B | 用于ER25弹簧夹头刀柄 | |||
| CN32B | 42 50 | M32×1.5 M40×1.5 | 20 23 | YER32B | 用于ER32弹簧夹头刀柄 |
| CN40B | 63 | M50×1.5 | 26 | YER40B | 用于ER40弹簧夹头刀柄 |
ER螺母HS型 ER Nuts HS
| 型号 Model | 尺寸Size（mm) | W手ch | 描述 Description | |||
| BD | FTDZ | LF | WSC | |||
| W17D | 用于ER11弹簧夹头刀柄 | |||||
| CN11HS CN16HS | 19 28 | M14×0.75 M22×1.5 | 11.3 17.5 | 17 25 | W25D | 用于ER16弹簧夹头刀柄 |
| CN20HS | 34 | M25×1.5 | 19 | 30 | W30D | 用于ER20弹簧夹头刀柄 |
ER螺母M型 ER Nuts M
内冷螺母Coolant Nuts
| 型号 Model | 尺寸Size(mm) | W扳手h | 描述 Description | ||
| BD | FTDZ | LF | |||
| 16 | WM11 | 用于ER11卡簧接杆 | |||
| CNM11 CNM16 | 23 | M13×0.75 M19x1 | 12 18 | WM16 | 用于ER16卡簧接杆 |
| CNM20 | 28 | M24×1 | 19 | WM20 | 用于ER20卡簧接杆 |
\*小径螺母为卡簧接杆专用螺母。
| 型号 Model | 尺寸Size（mm) | Wreh | 描述 Description | ||
| BD | FTDZ | LF | |||
| CN20C | 34 | M25×1.5 | 24 | W30D | 用于ER20卡簧内冷 |
| CN32C | 50 | M40×1.5 | 28 | YER32B | 用于ER32卡簧内冷 |
HN螺母 HN Nuts
| 型号 Model | 尺寸Size（mm) | W扳手h | 描述 Description | ||
| BD | FTDZ | LF | |||
| HN16 | YER16H | 用于BER16刀柄 | |||
| HN20 | 30 35 | M22×1.5 M25×1.5 | 23 24 | YER20H | 用于BER20刀柄 |
| HN25 | 40 | M32×1.5 | 25.5 | YER25H | 用于BER25刀柄 |
止水垫圈 Sealing Disk
| 型号 Model | 库存 Stock | DCON (mm) | ISO | JIS | DIN | |||
| ISO529 | ISO529/ISO2283 | JISB4430 | DIN371 | DIN374/DIN376 | ||||
| DER20C-6 | DER32C-6 | 6 | M6 | M5/M6 | M8 | |||
| DER20C-6.5 | DER32C-6.5 | 0 | 6.5 | M6 | M8 | m8 | ||
| DER20C-7 | DER32C-7 | 0 | 7 | M10 | M10 | |||
| DER20C-8 | DER32C-8 | 0 | 8 | M8 | M10 | M8 | ||
| DER20C-8.5 | DER32C-8.5 | 0 | 8.5 | M12 | ||||
| DER20C-9 | DER32C-9 | 0 | 9 | M12 | M12 | |||
| DER20C-10 | DER32C-10 | 0 | 10 | M10 | M10 | |||
| DER32C-12 | 0 | 12 | M16 | |||||
| DER32C-12.5 | 0 | 12.5 | M16 | M16 | ||||
| DER32C-14 | 0 | 14 | M18/M20 | M18 | M18 | |||
| DER32C-15 | 15 | M20 | ||||||
| DER32C-16 | 。 | 16 | M22 | M20 | ||||
●标准库存订单生产
三面刃铣刀刀柄用垫圈WashersforSlotting CutterHolder
| 型号 | B | 描述 Description | |
| Model | (mm) 3,5,7,8，10,12 | ||
| SD13 SD16 | 3,5,7,8,10,12 | 用于XS13三面刃铣刀刀柄suitableforXS13three-sidemillingcutterhandle 用于XS16三面刃铣刀刀柄suitableforXS16three-sidemilingcutterhandle | |
| 3,5,7,8,10,12 | |||
| SD22 | 3,5,7,8,10,12 | 用于XS22三面刃铣刀刀柄suitableforXS22three-sidemillingcutter handle | |
| SD27 SD32 | 3,5,7,8,10,12 | 用于XS27三面刃铣刀刀柄suitableforXS27three-sidemillingcutter handle | |
| SD40 | 3,5,7,8,10,12 | 用于XS32三面刃铣刀刀柄suitableforXS32three-sidemillingcutter handle 用于XS40三面刃铣刀刀柄suitableforXS40three-sidemillngcutter handle | |
| B | SD50 | 3,5,7,8,10,12 | 用于XS50三面刃铣刀刀柄suitableforXS50three-sidemillingcutter handle |
HSK冷却液套管及扳手 HSKCoolantTubesAnd CoolantTubeWrenches
冷却液套管CoolantTube
| 型号 Model | 库存 Stock | 尺寸Size(mm) | ||||
| CNT | CND | LB | LB2 | |||
| TU-HSK63 | HSK-63 | M18×1 | 12 | 11.5 | 36.6 | |
| TU-HSK100 | ： | HSK-100 | M24×1.5 | 16 | 15.5 | 44.2 |
卸刀夹具
| 型号 Model | 库存 Stock | 尺寸Size（mm) | 适用刀柄 Suitablefor Handle | ||||||
| OAL | OAH | OAW | LB | B | TDZ | ||||
| T-M/BT30 | 96 | 184 | 40 | M8 | BT30 | ||||
| T-M/BT40 | 。 ： | 30 40 | 200 272 | 133 | 64 85 | 248 | 55 | M12 | BT40 |
| T-M/BT50 | 50 | 364 | 168 | 125 | 338 | 85 | M12 | BT50 | |
| T-M/HSK63I | HSK63 | 272 | 135 | 85 | 248 | 55 | M12 | HSK63A,HSK63C | |
| T-M/HSK100I | 。 | HSK100 | 364 | 170 | 125 | 338 | 85 | M12 | HSK100A,HSK100C |
●标准库存 订单生产
清洁毛刷 Cleaning brushes
| 型号 Model | 库存 Stock | 适用孔径 (mm) |
| NLS-3 | 3 | |
| NLS-4 | 4 | |
| NLS-5 | . | 5 |
| NLS-6 | . | 6 |
| NLS-8 | . | 8 |
| NLS-10 | 10 | |
| NLS-12 | 12 | |
| NLS-14 | . | 14 |
| NLS-16 | . | 16 |
| NLS-18 | 18 | |
| NLS-20 | . | 20 |
| NLS-25 NLS-32 | 25 32 | |
^ * 用于热装刀柄内孔清洁。
●标准库存订单生产
●标准库存订单生产
可换杆定扭矩扳手Torque screwdriver
| 型号 | 库存 | 扭矩 | 适用螺钉规格 | 误差 | 尺寸 | ||
| DCONWS | Sizealm) | B | |||||
| 0.6 | M2 | ||||||
| TH06 | M2.2 | ||||||
| TH09 | 0.9 | M2.5 | |||||
| TH12 TH20 | 1.2 2.0 | M3 | |||||
| TH30 | 3.0 | M3.5 | 130 | ||||
| 3.8 | M4 | ±10% | 4 | 34 | |||
| TH38 | M4.5 | ||||||
| TH45 TH50 | . | 4.5 5.0 | M5 | ||||
星形可换扳手杆 Interchangeableblade. For torque screwdrivers.
| 型号 | 库存 od | 适用螺钉规格 | 尺寸 | ||
| DCON | Sizelm) | LPR | |||
| SRT5 | . | C020A05S | |||
| L60_M2x4.0 | 4 175 | ||||
| SRT6 | . | C020S05J | 42 | ||
| L60_M2.2x5.0 | |||||
| SRT7 | C022A06S C025A07S | ||||
| SRT8 | L60_M2.5x5.2 | ||||
| SRT9 | C030A07S | ||||
| SRT10 | L60_M3x6.0 | ||||
| SRT15 | L60_M3.5x8.8 | ||||
| C035A08S | |||||
| C035A12S | |||||
| L60_M4x8.4 | |||||
| C040A09S | |||||
| C040A11S | |||||
| SRT20 | . | L60_M4.5x10.8 C00.15x10.5 | |||
| C050A12S | |||||
刀片螺钉预载扭矩推荐值
| 螺钉型号 | 螺纹尺寸 | 推荐扭矩值 (Nm) |
| C62M2x4,0 | m2 | 0.6 |
| 602235. | M2.2 | 0.9 |
| L60M2.52 | m2.5 | 1.2 |
| L60M3x6. | M3 | 2.0 |
| L60M3.5x8.8 C035A08S | M3.5 | 3.0 |
| C035A12S L60M4x8.4 | ||
| C040A09S | M4 | 3.8 |
| C040A11S | M4.5 | |
| 60M4.5x10.8 | 4.5 | |
| L60M5x10.5 | m5 | 5.0 |
拉钉扳手Pull Nail Wrench
| 型号 | 库存 | 尺寸Size | torque(·m) | 重量weight | 适用拉钉的标准 | ||||
| OAL | (m) | WSC2 | |||||||
| B1 | WSC, | ||||||||
| PW-BT30 PW-BT40 | 210 230 | 16 | 5 | 7 10 | 13 19 | ≤80 ≤150 | 0.31 0.43 | MAS403-1975 MAS403-1975 | |
| PW-BT50 | . | 280 | 25 33 | 6 10 | 17 | 30 | ≤280 | 0.84 | MAS403-1975 |
操作方法
操作步骤：
1.如左图所示，将拉钉扳手的扳手头卡住拉钉颈部和法兰台阶。
2.手臂均匀用力，向左扳动可锁紧拉钉，向右扳动可松开拉钉。
注意事项：
1.操作前，注意刀柄要固定牢靠。
2.切勿使用加长杆增加力矩。
3.切勿使用锤子等敲击扳手。
4.BT系列拉钉扳手仅适用于对应BT系列之 4 5 ^ { \circ } 7
6 0 ^ { \circ } 和 9 0 ^ { \circ } 拉钉。
ER螺母扳手 ERNutsWrench
| 型号 Model | 库存 Stock | 尺寸Size | 描述 Description | ||
| LF | (mm) B1 | WF | |||
| PW-ER25B PW-ER32B | 250 270 | 35 45 | 5 5 | 用于ER25螺母B型suitableforER16NutsHS 用于ER32螺母B型suitableforER16NutsHS | |
| PW-ER40B | . | 300 | 57 | 5 | 用于ER40螺母B型suitableforER16NutsHS |
●标准库存订单生产
HS螺母扳手 HSNuts Wrench
| 型号 Model | 库存 Stock | 尺寸Size | 描述 Description | |
| (mm) LF | WSC | |||
| PW-ER16HS PW-ER20HS | ： | 225 240 | 25 30 | 用于ER16螺母HS型suitableforER16NutsHS 用于ER20螺母HS型suitableforER20NutsHS |
●标准库存 订单生产
HN螺母扳手 HNNuts Wrench
| 型号 Model | 库存 | 描述 Description |
| YER16H | 用于BER16弹簧夹头刀柄suitableforBER16colletchuckhandle | |
| YER20H | O | 用于BER20弹簧夹头刀柄suitableforBER20colletchuckhandle |
| YER25H | 。 | 用于BER25弹簧夹头刀柄suitableforBER25colletchuckhandle |
\*附件需单独订购。
注意事项
A
错误的使用可能会导致危险情况的发生。
为了防止意外情况的发生，请务必认真阅读样本中带！的说明。
安装刀具，拆卸刀具时注意事项
·请将刀柄牢固的固定在卸刀夹具上，然后再进行刀具的安装与拆卸操作。
·在安装刀具时请勿将手直接与刀刃接触，防止将手划伤。
·为了保证刀具的安全安装，请务必使用我公司提供的紧固扳手。
·在将刀具安装上机床时，请务必确认刀具上所有的紧固件已被锁紧。
加工时注意事项
·请勿接触旋转中的刀柄或刀具。
·加工时请穿戴防护服及护目镜，防止飞溅的高温切屑的伤害。
·加工时为防止意外事故的发生，在刀具旋转时请勿打开机床的防护门。
刀具长期保养注意事项
·刀具长期不使用时，请将刀具从刀柄中拆卸下来，否则会导致刀柄的夹持力和夹持精度的下降及联接面的锈蚀。
·保存前请将刀具、刀柄上的切屑及切削液清理干净，并进行适当的防锈处理，如涂覆防锈油等。
