该页无缩略图
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 9/9/18 |
| 按照EN 61 984 的电气数据 Electrical data according to EN 61 984 | |
| 一额定电流Ratedcurrent | 40A/16A/10A |
| -额定电压 Rated voltage | 830V/830V/250V |
| -额定脉冲电压 Rated pulse voltage | 8kV/8kV/4kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 阻燃等级 Flame retardant rating | vo |
| 可拔插次数Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金Copper alloy |
| 表面处理 Surface treatment | 镀金Gild |
| 镀银Silvering | |
| 接触电阻 Contact resistance | ≤3mΩ |
| -冷压连接Cold-pressed connection | |
| -mm² | 1.5-6mm2/0.14-4mm2/0.14-2.5mm |
| -AWG | 16-10/26-12/26-14 |
| 剥线长度 Stripping length | 9.5 / 7.5 / 8 (6)mm |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
冷压连接 Crimp terminal
830V/830V/250V 40/16A/10A 9/9/18+
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
| WUWEE | 公/Male | HK-009/9/18-MC | M3x10 日 日日 87.5 27 34 |
| VEVEE | 母/Female | HK-009/9/18-FC | M3x10 88888 440.4- 27 77.5 84.6 34 |
10A 冷压针 Crimp contacts
| 公/Male | 母/FemaleCDSF-0.25 | |||||
| CDSM-0.25 | ||||||
| CDSM-0.37 | CDSF-0.37 | |||||
| CDSM-0.50 | CDSF-0.50 | |||||
| CDSM-0.75 | CDSF-0.75 | |||||
| CDSM-1.0 | CDSF-1.0 | |||||
| CDSM-1.5 | CDSF-1.5 | |||||
| 线规 Wire gague | ① | 剥线长度 Stripping length | ||||
| CDSM-2.5 | CDSF-2.5 | |||||
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm | |||
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm | |||
| CDGM-0.25 | CDGF-0.25 | 0.5mm^2 | AWG 20 | 1.1 | 8mm | |
| CDGM-0.37 | CDGF-0.37 | 0.75mm2 | AWG 18 | 1.3 | 8mm | |
| CDGF-0.50 | ||||||
| 1mm2 | AWG 18 | 1.45 | 8mm | |||
| CDGM-0.50 | ||||||
| 1.5mm2 | AWG 16 | 1.75 | 8mm | |||
| CDGM-0.75 | CDGF-0.75 | 2.5mm2 | AWG 14 | 2.25 | 6mm | |
| CDGM-1.0 | CDGF-1.0 | 当线规小于0.75mm²时，建议使用辅助装针工具TL15When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliaryneedle mounting tool TL15 | ||||
| CDGM-1.5 | CDGF-1.5 | |||||
| CDGM-2.5 | CDGF-2.5 | |||||
16A 冷压针Crimp contacts
镀金/Gild
| 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |
| no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm |
| no groove | 0.5mm2 | AWG 20 | 7.5mm |
| 1 groove | 0.75mm2 | AWG 18 | 7.5mm |
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm |
| 2 groove | 1.5mm2 | AWG 16 | 7.5mm |
| 3 groove | 2.5mm² | AWG 14 | 7.5mm |
| wide groove | 3.0mm2 | AWG 12 | 7.5mm |
| no groove | 4.0mm2 | AWG 12 | 7.5mm |
| 工具/Tool | 压接线经/Press wire | 型号/Type |
 | 0.37-4mm2 | CRIMPBOX- 0.5/4 |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 10A、16A 冷压针 Cold press needle | REMOV-HD REMOV-HEE |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
40A 冷压针 Crimp contacts
| CCGM-1.5 | CCGF-1.5 |
| CCGM-2.5 | CCGF-2.5 |
| CCGM-4.0 | CCGF-4.0 |
| CCGM-6.0 | CCGF-6.0 |
| 工具/Tool | 压接线经/Press wire | 型号/Type |
| 冷压钳 Cold press pliers | 1.5-6mm2 | TL06G |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 40A 冷压针 Cold press needle | REMOV-MM |
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 1.5mm2 | AWG 16 | 1.75 | 9.6mm |
| 2.5mm2 | AWG 14 | 2.25 | 9.6mm |
| 4mm2 | AWG 12 | 2.85 | 9.6mm |
| 6mm2 | AWG 10 | 3.5 | 9.6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
面板安装开孔图 Panel installation holes
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
面板安装开孔图 Panel installation holes
技术参数 Technical parameter
| 规范/认证Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 32/55 |
| 按照EN 61 984 的电气数据 Electrical data according to EN 61 984 | |
| 信号区 Safe zone | |
| 一额定电流 Rated current | 4A |
| 一额定电压 Rated voltage | 50V |
| -额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 2 |
| 电力区 Power region | |
| -额定电流 Rated current | 10A |
| -额定电压 Rated voltage | 250V |
| -额定脉冲电压 Rated pulse voltage | 4kV |
| -污染程度Pollutionlevel | 2 |
| 依据UL/CSA额定电压 According to UL/CSA rated voltage | 600V |
| 绝缘电阻 Insulation resistance | ≥10°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 阻燃等级 Flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金Copper alloy |
| 表面处理 Surface treatment | 镀金Gild |
| 镀银Silvering | |
| 接触电阻 Contact resistance | ≤3mΩ |
| -冷压连接Cold-pressed connection | |
| -mm2 | 1.5-6mm2/0.14-4mm2 0.14-2.5mm2 |
| -AWG | 16-10/26-12/26-14 |
| 剥线长度 Stripping length | 9.5 / 7.5 / 8 (6)mm |
冷压连接 Crimp terminal
830V/830V/250V 40/16A/10A 9/9/18+
外壳尺寸：匹配H10B外壳，详情参考173-228页 Housing size: Matching H10B housing, details refer to pages 173-228
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||||||
| -64 34 | Φ3.3 | 57 | |||||||
| 公/Male | HK-032/55-MC | M3X10 M | 3.6 | R3 50.5 | o | ||||
| 母/Female | HK-032/55-FC | M3X10 27 | 57 64 | 34 | 300 | 面板安装开孔图 R3 | Panel installation holes -57 Φ3.3 | ||
当线规小于0.75mm2时，建议使用辅助装针工具TL15
| CDGM-0.25 | CDGF-0.25 |
| CDGM-0.33 | CDGF-0.33 |
| CDGM-0.52 | CDGF-0.52 |
5A冷压针 Crimp contacts
| a | b | C | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
10A 冷压针 Crimp contacts
| 线规 Wire gague | φ | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm |
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm |
| 0.5mm2 | AWG 20 | 1.1 | 8mm |
| 0.75mm2 | AWG 18 | 1.3 | 8mm |
| 1mm2 | AWG 18 | 1.45 | 8mm |
| 1.5mm2 | AWG 16 | 1.75 | 8mm |
| 2.5mm2 | AWG 14 | 2.25 | 6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliary needle mounting tool TL15
当线规小十0.75mm时，建议使用辅助装针工具1L15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliary needle mounting tool TL15
当线规小十0.75mm时，建议使用辅助装针工具1L15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 9/12/25 |
| 按照EN 61 984 的电气数据 Electrical data according to EN 61 984 | |
| 信号区 Safe zone | |
| -额定电流 Rated current | 5A |
| 一额定电压 Rated voltage | 50V |
| 一额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollution level | 3 |
| 电力区 Power region | |
| 一额定电流 Rated current | 10A/40A |
| 一额定电压 Rated voltage | 250V/630V |
| 额定脉冲电压 Rated pulse voltage | 4kV/8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 阻燃等级 Flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金Copper alloy |
| 表面处理 Surface treatment | 镀金Gild |
| 镀银Silvering | |
| 接触电阻 Contact resistance | ≤3mΩ/1mΩ |
| -冷压连接Cold-pressed connection | |
| -mm² | 0.09-0.52mm2/0.14-2.5mm2 1.5-6mm2 |
| -AWG | 28-20/26-14/16-10 |
| 剥线长度 Stripping length | 5 / 8 / 9 (9.6)mm |
冷压连接 Crimpterminal
630V/250V/50V40/10A/5A 009/12/25+
外壳尺寸：匹配H16B外壳，详情参考173-228页 Housing size: Matching H16B housing, details refer to pages 173-228
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HK-009/12/25-MC |  |
 | 母/Female | HK-009/12/25-FC |  |
5A 冷压针 Crimp contacts
| CDGM-0.25 | CDGF-0.25 |
| CDGM-0.33 | CDGF-0.33 |
| CDGM-0.52 | CDGF-0.52 |
| a | b | c | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
当线规小于0.75mm2时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm², you are advised to use an auxiliary needle mounting tool TL15
10A 冷压针 Crimp contacts
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
| 接触电阻/Contact resistance ≤3m Ω | 公/Male | 母/Female |
| CDSM-0.25 | CDSF-0.25 | |
| CDSM-0.37 | CDSF-0.37 | |
| CDSM-0.50 | CDSF-0.50 | |
| CDSM-0.75 | CDSF-0.75 | |
| CDSM-1.0 | CDSF-1.0 | |
| CDSM-1.5 | CDSF-1.5 | |
| CDSM-2.5 | CDSF-2.5 | |
| CDGM-0.25 | CDGF-0.25 | |
| CDGM-0.37 | CDGF-0.37 | |
| CDGM-0.50 | CDGF-0.50 | |
| CDGM-0.75 | CDGF-0.75 | |
| CDGM-1.0 | CDGF-1.0 | |
| CDGM-1.5 | CDGF-1.5 | |
| CDGM-2.5 | CDGF-2.5 |
| 线规 Wire gague | φ | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm |
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm |
| 0.5mm2 | AWG 20 | 1.1 | 8mm |
| 0.75mm2 | AWG 18 | 1.3 | 8mm |
| 1mm2 | AWG 18 | 1.45 | 8mm |
| 1.5mm2 | AWG 16 | 1.75 | 8mm |
| 2.5mm2 | AWG 14 | 2.25 | 6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm, you are advised to use an auxiliary needle mounting tool TL15
When the cable gauge is smaller than 0.75mm, you are advised to use an auxiliary needle mounting tool TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool
| 工具/Tool | 压接线经/Press wire | 型号/Type |
| 冷压钳 Cold press pliers | 1.5-6mm2 | TL06G |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 40A 冷压针 Cold press needle | REMOV-MM |
当线规小于0.75mm²时，建议使用辅助装针工具TL15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
40A 冷压针 Crimp contacts
| CCGM-1.5 | CCGF-1.5 |
| CCGM-2.5 | CCGF-2.5 |
| CCGM-4.0 | CCGF-4.0 |
| CCGM-6.0 | CCGF-6.0 |
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 1.5mm2 | AWG 16 | 1.75 | 9.6mm |
| 2.5mm2 | AWG 14 | 2.25 | 9.6mm |
| 4mm2 | AWG 12 | 2.85 | 9.6mm |
| 6mm2 | AWG 10 | 3.5 | 9.6mm |
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
面板安装开孔图 Panel installation holes
面板安装开孔图 Panel installation holes
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 按照EN 61 984 的电气数据 Electrical data according to EN 61 984 | |
| 电力区 Power region | |
| -接插件针数Pin number of connector | 4+PE |
| -额定电流 Rated current | 16A |
| 一额定电压 Rated voltage | 240V |
| -额定脉冲电压Rated pulse voltage | 4kV |
| -污染程度Pollutionlevel | 3 |
| -绝缘电阻Insulationresistance | ≥10^{°Ω |
| -材料 Materials | 聚碳酸酯 Polycarbonate |
| -颜色 Colour | RAL 7032(浅灰色Light grey) |
| -温度范围Temperature range | -40℃...+125℃ |
| 信号区 Safe zone | |
| -接插件针数Pin number of connector | 8 |
| -额定电流 Rated current | 1A |
| 一额定电压Rated voltage | 50V |
| -额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 阻燃等级 Flame retardant rating | VO |
| 可拔插次数Removable number of times | ≥500 |
| 传输特性Transmission characteristics | 超6类可达500MHz Super Category 6 reachable 500MHz |
| 传输速度 Transmission speed | |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金Copper alloy |
| 表面处理 Surface treatment | 镀金Gild |
| 镀银Silvering | |
| 接触电阻 Contact resistance | ≤1mΩ |
| -冷压连接Cold-pressed connection | |
| -mm2 | 0.37-4mm2 |
| -AWG | 33-12 |
冷压连接 Crimp terminal
240V/50V 16A/1A 4+
产品外观/Appearance | 插芯/Insert | 型号/Type |
尺寸图/Drawing   23.8A-A面板安装开孔图Panel installation holesM3X0.5   面板安装开孔图Panel installation holes | ||
| 公/Male | HY-004/RJ45-MC | |
 | 母/Female | HY-004/RJ45-FC |
16A 冷压针 Crimp contacts
镀金/Gild
| CEGM-0.37 | CEGF-0.37 |
| CEGM-0.50 | CEGF-0.50 |
| CEGM-0.75 | CEGF-0.75 |
| CEGM-1.0 | CEGF-1.0 |
| CEGM-1.5 | CEGF-1.5 |
| CEGM-2.5 | CEGF-2.5 |
| CEGM-3.0 | CEGF-3.0 |
| CEGM-4.0 | CEGF-4.0 |
| 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |
| no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm |
| no groove | 0.5mm2 | AWG 20 | 7.5mm |
| 1 groove | 0.75mm2 | AWG 18 | 7.5mm |
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm |
| 2 groove | 1.5mm2 | AWG 16 | 7.5mm |
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm |
| wide groove | 3.0mm2 | AWG 12 | 7.5mm |
| no groove | 4.0mm2 | AWG 12 | 7.5mm |
| 工具/Tool | 压接线经/Press wire | 型号/Type |
| 冷压钳 Cold press pliers | 0.14-4mm2 | TL02G |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 16A 冷压针 Cold press needle | REMOV-HEE |
当线规小于0.75mm²时，建议使用辅助装针工具TL15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
HM系 模块组合 型连接器
SUZHOU XIBASHI Provide a total solution for electrical connections! 苏州西霸士为电气连接提供整体解决方案!
技术参数Technical parameter
| 模块数量 Number of modules 2,3,4,6 | |
| 接地线 Ground wire | |
| -功率线Power line | 4-10mm2[选配PE-E16，可扩展到16mm2，仅适配高结构外壳或BK] 4-10mm2 [Optional PE-E16, extensible up to 16mm2, suitable only for high structure housing or BK] |
| AWG 12-8 | |
| -信号线Signal line | 1-2.5mm2 |
| 材料 Materials | 18-14 压铸锌合金 Die cast zinc alloy |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 可拔插次数 Removable number of times | ≥500 |
框架结构类型1,平推弹簧自复位结构Frame structure type1, flat push spring self-resetting structure 尺寸Size: 单位Unit mm
| 产品外观/Appearance | 描述/Description | 标示/Mark | |
尺寸图/DrawingHF6B-NUA3 HF6B-NLA3HF10B-NUA3  HF10B-NLA3   HF16B-NLA3HF24B-NUA3  HF24B-NLA3 | |||
6B适用所有6B外壳6B Applicable to all 6B housings | 用于2个模块For 2 modules | A-B | |
| 用于2个模块For 2 modules | a-b | ||
10B适用所有10B外壳10B Applicable to all 10B housings | 用于3个模块For 3 modules | A-C | |
| 用于3个模块For 3 modules | a-c | ||
16B适用所有16B外壳16B Applicable to all 16B housings | 用于4个模块For 4 modules | A-D | |
| 用于4个模块For 4 modules | a-d | ||
24B适用所有24B外壳24B Applicable to all 24B housings | 用于6个模块For 6 modules | A-F | |
| 用于6个模块For 6 modules | a-f |
| 模块框架适用于H10A外壳 The module framework is applicable to the Hi0A housing | 描述/Description | 型号/Type | 尺寸图/Drawing |
 | HF10A |
技术参数 Technical parameter
| 模块数量 Number of modules | 2,3,4,6 |
| 接地线 Ground wire | |
| -功率线 Power line | 4-10mm2[选配PE-E16，可扩展到16mm2，选配PE-E25，可扩展到25mm2仅适配高结构外壳或BK] 4-10mm² [Optional PE-E16, extendable to 16mm2, optional PE-E25, extendable to 25mm2 for high structure housing or BK only |
| AWG 12-8 | |
| -信号线Signal line | 1-2.5mm2 |
| 18-14 | |
| 材料Materials | 压铸锌合金 Die cast zinc alloy |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 可拔插次数 Removable number of times | ≥500 |
框架结构类型2,平推弹簧自复位结构Frame structure type 2, flat push spring self-resetting structure 尺寸Size:单位Unit mm
| 产品外观/Appearance | 描述/Description | 标示/Mark | 型号/Type |
6B适用所有6B外壳6B Applicable to all 6B housings | 用于2个模块For 2 modules | A-B | |
| 用于2个模块For 2 modules | a-b | ||
10B适用所有10B外壳10B Applicable to all 10B housings | 用于3个模块For 3 modules | A-C | |
| 用于3个模块For 3 modules | a-c | ||
16B适用所有16B外壳16B Applicable to all 16B housings | 用于4个模块For 4 modules | A-D | HF16B-NUA2HF16B-NLA2 |
| 用于4个模块For 4 modules | a-d | ||
24B适用所有24B外壳24B Applicable to all 24B housings | 用于6个模块For 6 modules | A-F | HF24B-NUA2 |
| 用于6个模块For 6 modules | a-f | HF24B-NLA2 | |
固定块(每个框架配有2 pcs)Fixed block (2 pcs per frame) |
技术参数 Technical parameter
| 规范/认证Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 1 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | |
| 一额定电流Rated current | 300A |
| 一额定电压 Rated voltage | 1000V AC 1300V DC |
| -额定脉冲电压 Rated pulse voltage | 8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{10°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级According to UL 94 flame retardant rating V0 | |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | ≤0.3mΩ |
| 冷压连接Cold-pressed connection | |
| -mm2 | 70-120mm^2 |
| -剥线长度 Strip length | 23.5mm |
| (当电缆绝缘层外径≥22mm，公针31mm，母针29.5mm) When the outer diameter of the cable insulation layer is ≥22mm, the male needle is 31mm and the female needle is 29.5mm. | |
冷压连接 Cold-pressed connection
1000V 300A
It can be used in combination with the framework and all other module products
可与框架及其他所有模块产品组合使用
| 产品外观/Appearance | 插芯/Insert | 型号/Type | |
 | 公/Male | H2MK300-001-MC | M  |
 | 母/Female | H2MK300-001-FC | F  |
300A 冷压针 Crimp contacts
| 接触电阻/Contact resistance ≤3m Ω | 公/Male | 母/Female | 尺寸图/Drawing | |||||
| 镀银/Silvering | CHSM300-70 | CHSF300-70 | ||||||
| CHSM300-95 | CHSF300-95 | |||||||
  | CHSM300-120 | CHSF300-120 |  |  | ||||
| 注意事项:冷压压接工具关系产品的质量稳定性， 请选择我司专用工具。 | θ1 | F | ||||||
| Note: The cold pressing crimping tool is related to t he quality and stability of the product, please choose | ||||||||
| 导线截面 | D | |||||||
| our special tool. | Traverse section 70 mm2 | ① 11.5 | 剥线长度 Stripping length | |||||
| 工具/Tool | 压接线经/Press wire | 型号/Type | 95 mm2 | 13.5 | 16.5mm 19mm | 23.5mm 23.5mm | 22mm 22mm | |
液压钳 Hydraulic tongs  | 10-240mm2 | TL05 | 120 mm^2 | 15.5 | 20.95mm | 23.5mm | 22mm | |
| 当绝缘皮外径≥22mm时：公针剥线长度为31mm | When the outer diameter of the insulating sheath is ≥22mm: The length of | |||||||
| the male needle stripped wire is 31mm 母线剥线长度为29.5mm The stripping length of the busbar is 29.5mm | ||||||||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 1 |
| 依据 EN 61 984的电气数据 Electrical data according to EN 61984 | |
| -额定电流Rated current | 200A |
| 一额定电压Rated voltage | 1000V |
| -额定脉冲电压Rated pulse voltage | 8kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 600V |
| 绝缘电阻 Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | 0.2mΩ |
| 电缆绞线依据IEC 60228-5 The cables are twisted according to IEC 60 228-5 | |
| 轴向螺栓连接 Axial bolted connection | |
| -mm2 | 25-70mm2 |
| -AGW | 2-0 |
| -内六角扳手 Hex key | SW 5 |
| -剥线长度 Strip length | 16mm |
| -拧紧力矩Tighteningmoment | |
| -mm² | 25 35 50 70 |
| -Nm | 8 8 9 10 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带3个模块，导线截面:70mm²
24B housing with 3 modules, wire cross section: 70mm2
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
口  | 公/Male | H2MK-001.1-M (25-40mm2) H2MK-001.2-M (40-70mm2) | 54.5 -29.4 -23- 34.2 M SW5 热缩管Schrumpfschlauch |
| 母/Female | H2MK-001.1-F (25-40mm2) H2MK-001.2-F (40-70mm2) | 60 29.4 -23 34.-- F SW5 热缩管 Schrumpfschlauch |
附件 Attachments
| 工具/Tool | 描述/Description | 型号/Type | |
| 内六角扳手/Hex key | 用于轴向夹紧螺栓 带T型把手 Used for axial clamping bolts | SW-5*150 | |
| With a T-handle | |||
技术参数 Technical parameter
| 规范/认证 Specification/Certification |
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHSCe |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 1 |
| 依据 EN 61984的电气数据 Electrical data according to EN 61984 |
| -额定电流Rated current 200A |
| -额定电压 Rated voltage 1000V |
| -额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollutionlevel 3 |
| 绝缘电阻Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围 Operating temperature range -40℃...+125℃ |
| 依据UL 94的阻燃等级 VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤0.3mΩ |
| 冷压连接Cold-pressed connection |
| -mm2 25-70mm2 |
| 剥线长度 Strip length 22.5mm |
| 最大电缆直径 Maximum cable diameter 18mm |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带3个模块，导线截面:70mm²
24B housing with 3 modules, wire cross section: 70mm
24B外壳带3个模块，导线截面:50mm²
24B housing with 3 modules, wire cross section: 50mm2
1000V 200A
冷压连接 Cold-pressed connection
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | H2MK-001-MC |  | ||
 | 母/Female | H2MK-001-FC |  | ||
200A 冷压针Crimp contacts
| 接触电阻/Contact resistance ≤3m Ω | 公/Male | 母/Female | 尺寸图/Drawing | |||
| 镀银/Silvering | CHSM200-25 CHSM200-35 | CHSF200-25 CHSF200-35 | ||||
 | CHSM200-50 | CHSF200-50 |  |  | ||
| CHSM200-70 CHSF200-70 | ||||||
| 注意事项：冷压压接工具关系产品的质量稳定性， | ||||||
| 工具/Tool | 压接线经/Press wire | 型号/Type | 导线截面 Traverse section 25 mm2 | ① | 剥线长度 Stripping length | |
| 液压钳 Hydraulic tongs | 10-240mm2 | 7 | 22.5mm | |||
| 35 mm2 | 8.2 | 22.5mm | ||||
| 50 mm2 | 10 | 22.5mm | ||||
 | 70 mm2 | 11.5 | 22.5mm | |||
| 电缆绞线依据 IEC 60 228-5 The cables are twisted according to IEC 60 228–5 | ||||||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 1 |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | |
| 一额定电流Rated current | 100A |
| -额定电压 Rated voltage | 330V |
| -额定脉冲电压Rated pulse voltage | 8kV |
| -污染程度Pollutionlevel | 3 |
| -绝缘电阻Insulationresistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | |
| 最大绝缘直径Maximuminsulation diameter | 13mm |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | ≤0.3mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm2 | 10-35mm2 |
冷压连接Cold-pressed connection
830V 100A
可与框架及其他所有模块产品组合使用，不匹配侧出线单模块外壳:EMC、H1M、WU-SE-M20
Can be used in combination with the frame and all other module products, the mismatched side outgoing single module housing: EMC, H1M, WU-SE-M20
| 产品外观/Appearance | 插芯/Insert | 型号/Type | |
尺寸图/Drawing  | |||
 | 公/Male | HMK-001-MC | |
 | 母/Female | HMK-001-FC |
100A 冷压针 Crimp contacts
| 接触电阻/Contact resistance ≤3m Ω | 公/Male | 母/Female | 尺寸图/Drawing | |||
| 镀银/Silvering | CKSM-10 | CKSF-10 | 10 42 | 88 | ||
| CKSM-16 | CKSF-16 | A | ||||
 | 39.95 | |||||
| CKSM-25 | CKSF-25 | 16  | ||||
| CKSM-35 | CKSF-35 | 39.45 | ||||
| 镀金/Gild | 注意事项:冷压压接工具关系产品的质量稳定性， 请选择我司专用工具。 | |||||
| 25 | ||||||
| 41 | 38.95 | |||||
| Note: The cold pressing crimping tool is related to t he quality and stability of the product, please choose | 35 | θ | ||||
| 工具/Tool | 压接线经/Press wire | 型号/Type |
液压钳 RE Hydraulic tong  | 10-240mm2 5 | TL05 |
| 适用范围/Scope of application | 型号/Type | |
| 100A冷压针Cold press needle | TL11 |
| 导线截面 Traverse section | ① | 剥线长度 Stripping length |
| 10 mm2 | 4.3 | 19mm |
| 16 mm2 | 5.5 | 19mm |
| 25 mm2 | 7 | 19mm |
| 35 mm^2 | 8.2 | 16mm |
技术参数 Technical parameter
| 规范/认证 Specification/Certification | ||
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 | |
| 认证Authentication | RoHS C∈ | |
| 插芯 Core insert | ||
| 接插件针数 Pin number of connector | 2 | |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | ||
| 一额定电流Rated current | 100A | |
| 一额定电压 Rated voltage | 1000V | |
| 一额定脉冲电压Rated pulse voltage | 8kV | |
| -污染程度Pollutionlevel | 3 | |
| 依据UL的额定电压 Rated voltage according to UL | 600V | |
| 绝缘电阻Insulation resistance | ≥10^{0Ω | |
| 材料 Materials | 聚碳酸酯 Polycarbonate | |
| 工作温度范围Operating temperature range | -40℃...+125℃ | |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo | |
| 可拔插次数 Removable number of times | ≥500 | |
| 插针 Inserting pin | ||
| 材料 Materials | ||
| 表面处理 Surface treatment | 铜合金 Copper alloy | |
| 接触电阻 Contact resistance | 镀银 Silvering 0.3mΩ | |
| 电缆绞线依据 IEC 60 228-5 | ||
| The cables are twisted according to IEC 60 228–5 轴向螺栓连接 Axial bolted connection | ||
| -mm^2 10-35mm2 | ||
| -AWG | ||
| -内六角扳手 Hex key | ||
| SW 4 -剥线长度Striplength | ||
| 13mm -拧紧力矩Tighteningmoment | ||
| 10 16 25 35 | ||
| -mm2 | ||
| -Nm | ||
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
轴向螺栓连接 Axial bolted connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
會  | 公/Male | H2MK-002.1-M (10-25mm²) H2MK-002.1-M (16-35mm²) | M   |
 | 母/Female | H2MK-002.1-F (10-25mm2) H2MK-002.1-F (16-35mm²) | F   |
附件Attachments
产品外观/Appearance
电缆终端 16mm²
描述/Description
用于PE扩展For PE expansion
型号/Type
PE-E162
电缆终端 25mm²
用于PE扩展For PE expansion
PE-E252
工具/Tool
描述/Description
尺寸图/Drawing
型号/Type
内六角扳手/Hex key
用于轴向夹紧螺栓
带T型把手
Used for axial clamping bolts
With a T-handle
SW-4\*150
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证Authentication RoHSC∈ |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 2 |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 |
| 一额定电流Rated current 100A |
| -额定电压 Rated voltage 1000V |
| -额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollution level 3 |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40C...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤0.3mΩ |
| 冷压连接 Cold-pressed connection |
| -mm2 10-35mm2 |
| 最大电缆直径Maximum cable diameter 14mm |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带3个模块，导线截面:35mm²
24B housing with 3 modules, wire cross section: 35mm²
接触电阻/Contact resistance ≤3m Ω镀银/Silvering 镀金/Gild | |||
| 公/Male | 母/Female | ||
尺寸图/Drawing | |||
| CKSM-10 | CKSF-10 | ||
| CKSM-16 | CKSF-16 | ||
| CKSM-25 | CKSF-25 | ||
| CKSM-35 | CKSF-35 | ||
| CKGM-10 | CKGF-10 | ||
| CKGM-16 | CKGF-16 | ||
| CKGM-25 | CKGF-25 | ||
| CKGM-35 | CKGF-35 | ||
电缆绞线依据IEC 60 228-5 The cables are twisted according to IEC 60 228–5
轴向螺栓连接 Axial boltedconnection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
100A冷压针 Crimp contacts
100A冷压针 Crimp contacts
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
盲 | 公/Male | H2MK-002-MC |
8 | 母/Female | H2MK-002-FC |
| 导线截面 Traverse section | ① | 剥线长度 Stripping length |
| 10 mm^2 | 4.3 | 19mm |
| 16 mm2 | 5.5 | 19mm |
| 25 mm2 | 7 | 19mm |
| 35 mm2 | 8.2 | 16mm |
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。
Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证Specification/Certification | ||
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 | |
| 认证 Authentication | RoHSCe | |
| 插芯 Core insert | ||
| 接插件针数 Pin number of connector | 2 | |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | ||
| -额定电流 Rated current | 70A | |
| -额定电压 Rated voltage | 1000V | |
| -额定脉冲电压 Rated pulse voltage | 8kV | |
| -污染程度Pollutionlevel | 3 | |
| 依据UL的额定电压 Rated voltage according to UL | 600V | |
| 绝缘电阻Insulation resistance | ≥101°Ω | |
| 材料 Materials | 聚碳酸酯 Polycarbonate | |
| 工作温度范围Operating temperature range | -40℃...+125℃ | |
| 依据UL 94 的阻燃等级 | Vo | |
| According to UL 94 flame retardant rating 可拔插次数 Removable number of times | ≥500 | |
| 插针 Inserting pin | ||
| 材料 Materials | 铜合金 Copper alloy | |
| 表面处理 Surface treatment | 镀银 Silvering | |
| 接触电阻 Contact resistance | 0.5mΩ | |
| 电缆绞线依据 IEC 60 228-5 The cables are twisted according to IEC 60 228-5 | ||
| 轴向螺栓连接 Axial bolted connection | ||
| -mm2 -AWG | 6-22mm2 8-4 | |
| -内六角扳手 Hex key | SW 2.5 | |
| -剥线长度 Strip length | ||
| -mm2 | 6 10 16 22 | |
| -mm2 | 111111112.51 | |
| -拧紧力矩Tighteningmoment | ||
| -mm^2 | 6 10 16 22 | |
| -Nm | 2 3 4 5 | |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带6个模块，导线截面:22mm²
24B housing with 6 modules, wire cross section: 22mm
24B外壳带6个模块，导线截面:16mm²
24B housing with 6 modules, wire cross section: 16mm2
24B外壳带6个模块，导线截面:6mm²
24B housing with 6 modules, wire cross section: 6mm2
轴向螺栓连接 Axial bolted connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
| 公/Male | HMK70-002.1-M (6-16mm²) HMK70-002.2-M (14-22mm²) | 14.6- 34.2 E M | |||
| 福 | 母/Female | HMK70-002.1-F (6-16mm2) HMK70-002.2-F (14-22mm²) | -14.6- 46.5 日 F 34.2 m | ||
附件Attachments
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范/认证 Specification/Certification | ||
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 | |
| 认证 Authentication | RoHS C∈ | |
| 插芯 Core insert | ||
| 接插件针数Pin number of connector | 2 | |
| 依据 EN 61 984 的电气数据Electrical data according to EN 61984 | ||
| -额定电流Rated current | 40A | |
| -额定电压 Rated voltage | 1000V | |
| -额定脉冲电压 Rated pulse voltage | 8kV | |
| -污染程度Pollutionlevel | 3 | |
| 依据UL的额定电压Rated voltage according to UL | 600V | |
| 绝缘电阻Insulation resistance | ≥10^{°Ω | |
| 材料 Materials | 聚碳酸酯 Polycarbonate | |
| 工作温度范围Operating temperature range | -40℃...+125℃ | |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo | |
| 可拔插次数 Removable number of times | ≥500 | |
| 插针 Inserting pin | ||
| 材料 Materials | 铜合金 Copper alloy | |
| 表面处理 Surface treatment | 镀银 Silvering | |
| 接触电阻 Contact resistance | 1mΩ | |
| 轴向螺栓连接 Axial bolted connection | ||
| 2.5-10mm2 | ||
| -mm2 -AWG | 14-8 | |
| -内六角扳手 Hex key | SW 2 | |
| -剥线长度 Strip length | ||
| -mm2 | 2.5 4 6 10 | |
| -mm2 | 515{181 11+1 | |
| -拧紧力矩Tighteningmoment | ||
| -mm2 | 2.5 4 6 10 | |
| -Nm | 1.5 1.5 2 2 | |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
轴向螺栓连接 Axial bolted connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HMK-002.1-M (2.5-8mm2) HMK-002.2-M (6-10mm2) |   |
福F  | 母/Female | HMK-002.1-F (2.5-8mm2) HMK-002.2-F (6-10mm2) |   |
附件 Attachments
| 工具/Tool | 描述/Description | 型号/Type | |
| 内六角扳手/Hex key | 用于轴向夹紧螺栓 带T型把手 Used for axial clamping bolts | SW-2*100 | |
| With a T-handle |  |
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHSCE |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 2 |
| 依据 EN 61 984的电气数据Electrical data according to EN 61984 |
| -额定电流 Rated current 40A |
| -额定电压 Rated voltage 1000V |
| -额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollution level 3 |
| 依据UL的额定电压 Rated voltage according to UL 600V |
| 绝缘电阻Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤1mΩ |
| 冷压连接 Cold-pressed connection |
| -mm2 1.5-10mm2 |
| -AWG 16-8 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
40A 冷压针 Crimp contacts
40A 冷压针 Crimp contacts
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | HMK-002-MC |  | ||
 | 母/Female | HMK-002-FC | F  | ||
| 工具/Tool | 压接线经/Press wire | 型号/Type |
 | 1.5-6mm2 4/6/10mm2 | TL02-0G TL02-3G |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 40A 冷压针 Cold press needle | REMOV-MM |
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 1.5mm2 | AWG 16 | 1.75 | 9.6mm |
| 2.5mm2 | AWG 14 | 2.25 | 9.6mm |
| 4mm2 | AWG 12 | 2.85 | 9.6mm |
| 6mm2 | AWG 10 | 3.5 | 9.6mm |
| 10mm2 | AWG 8 | 4.3 | 12mm |
剥线长度A=15 mm用于电缆≥5 mmStrip cable length A=15 mm For cables ≥5 mm
剥线长度A=18 mm用于电缆≥6.4mmStrip cable length A=18 mm For cables ≥6.4 mm
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS CE |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 3 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 |
| 额定电流 Rated current 40A |
| 额定电压 Rated voltage 690V |
| -额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollutionlevel 3 |
| 依据UL的额定电压 Rated voltage according to UL 600V |
| 绝缘电阻 Insulation resistance ≥10^{0°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级voAccording to UL94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance 1mΩ |
| 轴向螺栓连接 Axial bolted connection |
| -mm2 2.5-10mm2 |
| -AWG 14-8 |
| -内六角扳手 Hex key SW2 |
| -剥线长度Strip length |
| -mm2 2.5 4 6 10 |
| -mm2 5158111+1 |
| -拧紧力矩Tighteningmoment |
| -mm2 2.5 4 6 10 |
| -Nm 1.5 1.5 2 2 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
轴向螺栓连接 Axial bolted connection
690V 40A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | HMK-003.1-M (2.5-8mm2) HMK-003.2-M (6-10mm2) |  | ||
| HMK-003.1-F | |||||
A  | (2.5-8mm2) 母/Female HMK-003.2-F (6-10mm2) |  | |||
附件 Attachments
| 工具/Tool | 描述/Description | 型号/Type | |
| 内六角扳手/Hex key | 用于轴向夹紧螺栓 带T型把手 | SW-2*100 | |
| Used for axial clamping bolts With a T-handle | |||
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 3 |
| 依据 EN 61 984的电气数据Electrical data according to EN 61984 | |
| 电缆直径 7.5mm 时 The cable diameter is 7.5mm | |
| -额定电流Rated current | 40A |
| -额定电压Rated voltage | 500V |
| -额定脉冲电压Rated pulse voltage | 6kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL/CSA的额定电压 Rated voltage according to UL/CSA | 600V |
| 依据UL/CSA的额定电流 Rated current according to UL/CSA | 32A |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40C...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | ≤1mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm2 | 1.5-10mm2 |
| -AWG | 16-8 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
冷压连接 Cold-pressed connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
O  | 公/Male | HMK-003-MC |  |
LI  | 母/Female | HMK-003-FC | F   |
40A冷压针 Crimp contacts
| 公/Male | 尺寸图/Drawing | ||||||
| CCSM-1.5 | CCSF-1.5 | ||||||
| CCSM-2.5 | CCSF-2.5 | ||||||
| CCSM-4.0 | 9φ | ||||||
| CCSF-4.0 | |||||||
| CCSM-6.0 | CCSF-6.0 | ||||||
| CCSM-10.0 | CCSF-10.0 | ||||||
| CCGM-1.5 | CCGF-1.5 | ||||||
镀金/Gild  | CCGM-2.5 | CCGF-2.5 | 23.6 | ||||
| CCGM-4.0 | CCGF-4.0 | ||||||
| CCGM-6.0 | CCGF-6.0 | ||||||
| CCGM-10.0 | |||||||
| 工具/Tool | 压接线经/Press wire | CCGF-10.0 型号/Type | 导线截面 Traverse section | ① | |||
| 1.5mm2 | AWG 16 | 剥线长度 Stripping length 1.75 | |||||
| 冷压钳 Cold press pliers | 2.5mm2 AWG 14 | 2.25 | 9.6mm 9.6mm | ||||
| 1.5-6mm2 4/6/10mm2 | TL02-0G TL02-3G | 4mm2 | AWG 12 | 9.6mm | |||
| 6mm2 | AWG 10 | 2.85 3.5 | 9.6mm | ||||
| 10mm2 | AWG 8 | 4.3 | 12mm | ||||
| 适用类型/Applicable type | 型号/Type | 剥线长度A=15mm用于电缆≥5mm | |||||
| Strip cable length A=15 mm For cables ≥5 mm | |||||||
| 退针器 Needle extractor | 40A 冷压针 Cold press needle | REMOV-MM | 剥线长度A=18 mm用于电缆≥6.4 mm Strip cable length A=18 mm For cables ≥6.4 mm | ||||
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 3/4 |
| 依据 EN 61 984的电气数据 Electrical data according to EN 61984 | |
| 电力区 Power region | |
| -额定电流Rated current | 40A |
| 额定电压 Rated voltage | 830V |
| -额定脉冲电压 Rated pulse voltage | 8kV |
| -污染程度Pollutionlevel | 3 |
| 信号区 Safe zone | |
| -额定电流Rated current | 10A |
| -额定电压 Rated voltage | 830V |
| 一额定脉冲电压Rated pulse voltage | 8kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 600V |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40C...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | VO |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | |
| -电力区 Power region | ≤1mΩ |
| -信号区 Safe zone | ≤3mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm2 | |
| -电力区 Power region | 1.5-6mm2 |
| -信号区 Safe zone | 0.14-2.5mm2 |
| -AWG | |
| -电力区 Power region | 10-10 |
| -信号区Safe zone | 26-14 |
| 最大电缆直径 Maximum cable diameter | |
| -电力区Power region | 5mm |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
24B外壳带6个模块，导线截面:6mm²
24B housing with 6 modules, wire cross section: 6mm
接触电阻/Contact resistance ≤1/3m Ω镀银/Silvering 镀金/Gild  | |||||||
| 母/Female | |||||||
尺寸图/Drawing  线规 Wire gague ① 剥线长度 Stripping length | |||||||
| CCSF-1.5 | |||||||
| CCSF-2.5 | |||||||
| CCSF-4.0 | |||||||
| CCSF-6.0 | |||||||
| CDSF-0.25 | 1.5mm^2 | AWG 16 | 1.75 | 9.6mm | |||
| CDSF-0.37 | 4mm2 | ||||||
| 2.5mm2 | AWG 14 | 2.25 | 9.6mm | ||||
| AWG 12 | 2.85 | 9.6mm | |||||
| CDSF-0.50 | 6mm^2M   | ||||||
| CDSF-0.75 | |||||||
| CDSF-1.0 | |||||||
| CDSF-1.5 | |||||||
| CDSF-2.5 | |||||||
| 线规 Wire gague | ① | 剥线长度 Stripping length | |||||
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm | ||||
| CDGF-0.25 | 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm | |||
| CDGF-0.37 | 0.5mm2 | AWG 20 | 1.1 | 8mm | |||
| CDGF-0.50 | |||||||
| 0.75mm2 | AWG 18 | 1.3 | 8mm | ||||
| 1mm2 | AWG 18AWG 16 | 1.45 | 8mm | ||||
| CDGF-0.75 | 1.5mm2 | ||||||
| 1.75 | 8mm | ||||||
| CDGF-1.0 | 2.5mm2 | AWG 14 | 2.25 | 6mm | |||
| CDGF-1.5 当线规小于0.75mm²时，建议使用辅助装针工具TL16When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliaryCDGF-2.5 needle mounting tool TL15 | |||||||
注意事项：冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
冷压连接 Cold-pressed connection
830/830V40A/10A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HMK-003/4-MC | M  |
 | 母/Female | HMK-003/4-FC | F  |
40A/10A冷压针 Crimp contacts
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHSCe |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 4 |
| 依据 EN 61 984的电气数据Electrical data according to EN 61984 |
| 一额定电流Rated current 40A |
| -额定电压 Rated voltage 830V |
| 额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollution level 3 |
| 依据UL/CSA的额定电压Rated voltage according to UL/CSA 600V |
| 绝缘电阻Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤1mΩ |
| 冷压连接 Cold-pressed connection |
| -mm² 1.5-6mm2 |
| -AWG 16-10 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
| 工具/Tool | 压接线经/Press wire | 型号/Type | 导线截面 Traverse section | ① 1.75 | 剥线长度 Stripping length 9.6mm | |
| 1.5mm2 | AWG 16 | |||||
 | 1.5-6mm2 | TL02-0G | 2.5mm2 | AWG 14 | 2.25 | 9.6mm |
| 4/6/10mm2 | TL02-3G | 4mm2 | AWG 12 | 2.85 | 9.6mm | |
| 6mm2 | AWG 10 | 3.5 | 9.6mm | |||
| 适用类型/Applicable type | 型号/Type | 剥线长度A=15 mm用于电缆≥5mm | ||||
| Strip cable length A=15 mm For cables ≥5 mm 剥线长度A=18 mm用于电缆≥6.4 mm | ||||||
冷压连接Cold-pressedconnection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
 | 公/Male | HMK-004-MC |
R | 母/Female | |
40A 冷压针 Crimp contacts
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS Ce |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 5 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 |
| 一额定电流Rated current 16A |
| -额定电压 Rated voltage 400V |
| -额定脉冲电压 Rated pulse voltage 6kV |
| -污染程度Pollutionlevel 3 |
| 依据UL/CSA的额定电压600VRated voltage according to UL/CSA |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VOAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤3mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.14-2.5mm2 |
| -AWG 26-14 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN 60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
装配说明Assembly instructions
第二步：顶部装线，侧边螺丝锁紧；Step 2: Install the wires on the top andtighten the screws on the side.
第一步：打开盖子；
The first step: Open the lid;第三步：合上盖子；
Step 3: Close the lid;
规范/认证 Specification/Certification
技术参数 Technical parameter
| 规/认证Specication/Certication |
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHSCe |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 5 |
| 依据 EN 61 984的电气数据Electrical data according to EN 61984 |
| 一额定电流Rated current 16A |
| -额定电压 Rated voltage 400V |
| -额定脉冲电压 Rated pulse voltage 6kV |
| -污染程度Pollutionlevel 3 |
| 依据UL/CSA的额定电压600VRated voltage according to UL/CSA |
| 绝缘电阻 Insulation resistance ≥10{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 接触电阻 Contact resistance ≤3mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.14-2.5mm2 |
| -AWG 26-14 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
弹片连接 Cage shrapnel connection
400V 16A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
| 公/Male | HME-005-MS | M 34 | 34.2 日 田 | 14.6 34 | |
| 母/Female | HME-005-FS | 日 F 34 田 曰 34.2 | |||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 5 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | |
| -额定电流 Rated current | 16A |
| -额定电压 Rated voltage | 500V |
| -额定脉冲电压 Rated pulse voltage | 6kV |
| 一污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{0Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 颜色 Colour | |
| 工作温度范围Operating temperature range 依据UL 94 的阻燃等级 | -40℃...+125℃ |
| According to UL94 flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 接线方式 Wiring method | 弹片连接(快接) Spring piece connection (quick connection) |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | ≤3mΩ |
| 线径范围 Screw connection | |
| -mm2 | 0.5-4.0mm2 |
| -AWG | 20-12 |
| 带管形接线端子线径范围The wire diameter range with tubular terminal blocks | |
| -mm^2 | 0.14-2.5mm2 |
| -AWG | 26-14 |
| 剥线长度 Stripping length | 10±0.5mm |
弹片连接Cage shrapnel connection
500V16A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | |
尺寸图/DrawingM     | |||
 | 公/Male | HME-006-MQ | |
尼 | 母/Female | HME-006-FQ |
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS Ce |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 5 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 |
| 一额定电流 Rated current 16A |
| -额定电压Rated voltage 500V |
| -额定脉冲电压 Rated pulse voltage 6kV |
| -污染程度Pollution level 3 |
| 依据UL/CSA的额定电压600VRated voltage according to UL/CSA |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级According to UL 94 flame retardant rating Vo |
| 可拔插次数Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| ≤1mΩ |
| 接触电阻 Contact resistance |
| 螺丝连接 Screw connection |
| -mm2 0.14-4mm2 |
| -AWG 26-12 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
冷压连接Cold-pressed connection
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HME-006-MC |  |
E  | 母/Female | HME-006-FC |  |
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
16A 冷压针 Crimp contacts
尺寸图/DrawingM   | |||||||||||
镀金/Gild | |||||||||||
| CEGM-0.37 | CEGF-0.37 | 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |||||||
| CEGM-0.50 | CEGF-0.50 | no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm | ||||||
| CEGM-0.75 | CEGF-0.75 | no groove | 0.5mm2 | AWG 20 | 7.5mm | ||||||
| CEGM-1.0 | CEGF-1.0 | 1 groove | 0.75mm2 | AWG 18 | 7.5mm | ||||||
| CEGM-1.5 | CEGF-1.5 | ||||||||||
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm | ||||||||
| CEGM-2.5 | CEGF-2.5 | ||||||||||
| 2 groove | 1.5mm² | AWG 16 | 7.5mm | ||||||||
| CEGM-3.0 | CEGF-3.0 | ||||||||||
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm | ||||||||
| CEGM-4.0 CEGF-4.0 | |||||||||||
| wide groove | 3.0mm2 | AWG 12 | 7.5mm | ||||||||
工具/Tool冷压钳 当线规小于0.75mm²时，建议使用辅助装针工具TL15CRIMPBOX-Cold press pliers When the cable gauge is smaller than 0.75mm2, you are advised to use an0.37-4mm20.5/4 auxiliary needle mounting tool TL15 适用类型/Applicable type 型号/Type注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。退针器 16A 冷压针 Note: The cold pressing crimping tool is related to the quality and stability of the Needle extractor REMOV-HEECold press needle product, please choose our special tool. | |||||||||||
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS Ce |
| 插芯 Core insert |
| 接插件针数Pin number of connector 6 |
| 依据EN 61 984 的电气数据Electrical data according to EN 61984 |
| -额定电流 Rated current 16A |
| -额定电压Rated voltage 830V |
| -额定脉冲电压 Rated pulse voltage 8kV |
| -污染程度Pollutionlevel 3 |
| 依据UL/CSA的额定电压600VRated voltage according to UL/CSA |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 镀金 Gild |
| 接触电阻 Contact resistance ≤1mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.14-4mm2 |
| -AWG 26-12 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
24B外壳带6个模块，导线截面:2.5mm²
24B housing with 6 modules, wire cross section: 2.5mm2
冷压连接Cold-pressed connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | HVME-006-MC |  |  | |
 | 母/Female | HVME-006-FC |   | ||
16A 冷压针 Crimp contacts
| 公/Male | 母/Female | ||||||||||
| CESM-0.37 | CESF-0.37 | ||||||||||
| CESM-0.50 | CESF-0.50 | ||||||||||
| CESM-0.75 | CESF-0.75 | ||||||||||
| CESM-1.0 | CESF-1.0 | ||||||||||
| CESM-1.5 | CESF-1.5 | ||||||||||
| CESM-2.5 | CESF-2.5 | ||||||||||
| CESM-3.0 | CESF-3.0 | ||||||||||
| CESM-4.0 | CESF-4.0 | ||||||||||
| CEGM-0.37 | CEGF-0.37 | 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |||||||
| CEGM-0.50 | CEGF-0.50 | no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm | ||||||
| CEGM-0.75 | CEGF-0.75 | no groove | 0.5mm2 | AWG 20 | 7.5mm | ||||||
| CEGM-1.0 | CEGF-1.0 | 1 groove | 0.75mm2 | AWG 18 | 7.5mm | ||||||
| CEGM-1.5 | CEGF-1.5 | 1 groove | 1.0mm2 | AWG 18 | 7.5mm | ||||||
| CEGM-2.5 | CEGF-2.5 | ||||||||||
| 2 groove | 1.5mm² | AWG 16 | 7.5mm | ||||||||
| CEGM-3.0 | CEGF-3.0 | ||||||||||
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm | ||||||||
| CEGM-4.0 | CEGF-4.0 | ||||||||||
| 压接线经/Press wire | 型号/Type | ||||||||||
| wide groove | 3.0mm2 | AWG 12 | |||||||||
工具/Tool7.5mm冷压钳 当线规小于0.75mm²时，建议使用辅助装针工具TL15Cold press pliers CRIMPBOX- When the cable gauge is smaller than 0.75mm2, you are advised to use an0.37-4mm20.5/4 auxiliary needle mounting tool TL15 适用类型/Applicable type 型号/Type注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。退针器 16A 冷压针 Note: The cold pressing crimping tool is related to the quality and stability of theNeedle extractor REMOV-HEECold press needle product, please choose our special tool. | |||||||||||
技术参数Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS Ce |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 8 |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 |
| 一额定电流Rated current 16A |
| 一额定电压 Rated voltage 400V |
| -额定脉冲电压 Rated pulse voltage 6kV |
| -污染程度Pollutionlevel 3 |
| 依据UL/CSA的额定电压Rated voltage according to UL/CSA 600V |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级VoAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 镀金 Gild |
| 接触电阻 Contact resistance ≤1mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.14-4mm2 |
| -AWG 26-12 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
冷压连接 Cold-pressed connection
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
 | 公/Male | HMEE-008-MC |
Fs | 母/Female | HMEE-008-FC |
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
16A 冷压针 Crimp contacts
| 公/Male | 母/Female | |||||||
| CESM-0.37 | CESF-0.37 | |||||||
| CESM-0.50 | CESF-0.50 | |||||||
| CESM-0.75 | CESF-0.75 | |||||||
| CESM-1.0 | CESF-1.0 | |||||||
| CESM-1.5 | CESF-1.5 | |||||||
| CESM-2.5 | CESF-2.5 | |||||||
| CESM-3.0 | CESF-3.0 | |||||||
| CESM-4.0 | CESF-4.0 | |||||||
| CEGM-0.37 | CEGF-0.37 | 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | ||||
| CEGM-0.50 | CEGF-0.50 | no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm | |||
| CEGM-0.75 | CEGF-0.75 | no groove | 0.5mm2 | AWG 20 | 7.5mm | |||
| CEGM-1.0 | CEGF-1.0 | 1 groove | 0.75mm2 | AWG 18 | 7.5mm | |||
| CEGM-1.5 | CEGF-1.5 | |||||||
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm | |||||
| CEGM-2.5 | CEGF-2.5 | |||||||
| 2 groove | 1.5mm2 | AWG 16 | 7.5mm | |||||
| CEGM-3.0 | CEGF-3.0 | |||||||
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm | |||||
| CEGM-4.0 CEGF-4.0 | ||||||||
| wide groove | 3.0mm2 | AWG 12 | 7.5mm | |||||
工具/Tool冷压钳 当线规小于0.75mm²时，建议使用辅助装针工具TL15Cold press pliers CRIMPBOX- When the cable gauge is smaller than 0.75mm2, you are advised to use an0.37-4mm2 auxiliary needle mounting tool TL150.5/4 型号/Type注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。退针器 16A 冷压针 Note: The cold pressing crimping tool is related to the quality and stability of the Needle extractor Cold press needle REMOV-HEE product, please choose our special tool. | ||||||||
| 适用类型/Applicable type | ||||||||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 8 |
| -额定电流Rated current | 16A |
| -额定电压 Rated voltage | 400V |
| 额定脉冲电压 Rated pulse voltage | 6kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 颜色 Colour | RAL 7032（浅灰色Light grey) |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 接线方式 Wiring method | 弹片连接(快接) Spring piece connection (quick connection) |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤3mΩ |
| 线径范围 Wire diameter range | |
| -mm2 | 0.5-4.0mm^2 |
| -AWG | 20-12 |
| 带管形接线端子线径范围The wire diameter range with tubular terminal blocks | |
| -mm2 | 0.14-2.5mm2 |
| -AWG | 26-14 |
| 剥线长度 Stripping length | 10±0.5mm |
弹片连接（快接)Spring piece connection (quick connection)
400V 16A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
尺寸图/DrawingM   F  | |||
产品外观/Appearance | 插芯/Insert | 型号/Type | |
| 公/Male | HMEE-008-MQ | ||
M | 母/Female | HMEE-008-FC |
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 20 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | |
| 一额定电流Rated current | 16A |
| -额定电压 Rated voltage | 500V |
| -额定脉冲电压 Rated pulse voltage | 6kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 600V |
| 绝缘电阻 Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤1mΩ |
| 螺丝连接 Screw connection | |
| -mm2 | 0.14-2mm2 |
| -AWG | 26-12 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带6个模块，导线截面:4mm²
24B housing with 6 modules, wire cross section: 4mm2
24B外壳带6个模块，导线截面:2.5mm²
24B housing with 6 modules, wire cross section: 2.5mm2
24B外壳带6个模块，导线截面:1.5mm²
24B housing with 6 modules, wire cross section: 1.5mm2
冷压连接 Cold-pressed connection
400V 16A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | H2MEE-020-MC |  | ||
 | 母/Female | H2MEE-020-FC |  | ||
16A 冷压针Crimp contacts
尺寸图/DrawingM   | |||||||||
接触电阻/Contact resistance ≤1m Ω镀银/Silvering 镀金/Gild | 公/Male | 母/Female | |||||||
| CESM-0.37 | CESF-0.37 | ||||||||
| CESM-0.50 | CESF-0.50 | ||||||||
| CESM-0.75 | CESF-0.75 | ||||||||
| CESM-1.0 | CESF-1.0 | ||||||||
| CESM-1.5 | CESF-1.5 | ||||||||
| CESM-2.5 | CESF-2.5 | ||||||||
| CESM-3.0 | CESF-3.0 | ||||||||
| CESM-4.0 | CESF-4.0 | ||||||||
| CEGM-0.37 | CEGF-0.37 | 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |||||
| CEGM-0.50 | CEGF-0.50 | no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm | ||||
| CEGM-0.75 | CEGF-0.75 | no groove | 0.5mm² | AWG 20 | 7.5mm | ||||
| CEGM-1.0 | CEGF-1.0 | 1 groove | 0.75mm2 | AWG 18 | 7.5mm | ||||
| CEGM-1.5 | CEGF-1.5 | 1 groove | 1.0mm² | AWG 18 | 7.5mm | ||||
| CEGM-2.5 | CEGF-2.5 | ||||||||
| 2 groove | 1.5mm² | AWG 16 | 7.5mm | ||||||
| CEGM-3.0 | CEGF-3.0 | ||||||||
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm | ||||||
| CEGM-4.0 CEGF-4.0 | |||||||||
| wide groove | 3.0mm2 | AWG 12 | 7.5mm | ||||||
工具/ToolCRIMPBOX- 当线规小于0.75mm2时，建议使用辅助装针工具TL150.37-4mm2 When the cable gauge is smaller than 0.75mm2, you are advised to use an0.5/4auxiliary needle mounting tool TL15 型号/Type注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。退针器 16A 冷压针 Note: The cold pressing crimping tool is related to the quality and stability of theNeedle extractor Cold press needle REMOV-HEE product, please choose our special tool. | |||||||||
| 适用类型/Applicable type | |||||||||
