该页无缩略图
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 12 |
| 依据EN 61984的电气数据Electrical data according to EN 61984 | |
| 一额定电流Rated current | 10A |
| -额定电压 Rated voltage | 250V |
| -额定脉冲电压Rated pulse voltage | 4kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 600V |
| 绝缘电阻 Insulation resistance | ≥10^{1°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤1mΩ |
| 螺丝连接 Screw connection | |
| -mm2 | 0.14-2.5mm2 |
| -AWG | 26-14 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
24B外壳带6个模块，导线截面:1.5mm²
24B housing with 6 modules, wire cross section: 1.5mm2
接触电阻/Contact resistance ≤3m Ω镀银/Silvering | 公/Male | 母/Female | |
| CDSM-0.25 | CDSF-0.25 | ||
| CDSM-0.37 | CDSF-0.37 | ||
| CDSM-0.50 | CDSF-0.50 | ||
| CDSM-0.75 | CDSF-0.75 | ||
| CDSM-1.0 | CDSF-1.0 | ||
| CDSM-1.5 | CDSF-1.5 | ||
| CDSM-2.5 | CDSF-2.5 | ||
冷压连接 Cold-pressed connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
尺寸图/Drawing    | ||
 | 公/Male | HMD-012-MC |
 | 母/Female | HMD-012-FC |
10A 冷压针 Crimp contacts
| 工具/Tool | 压接线经/Press wire | 型号/Type |
| 冷压钳 Cold press pliers | 0.37-4mm2 | CRIMPBOX- 0.5/4 |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 10A 冷压针 Cold press needle | REMOV-HD |
| 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |
| no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm |
| no groove | 0.5mm2 | AWG 20 | 7.5mm |
| 1 groove | 0.75mm2 | AWG 18 | 7.5mm |
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm |
| 2 groove | 1.5mm2 | AWG 16 | 7.5mm |
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm |
| wide groove | 3.0mm2 | AWG 12 | 7.5mm |
| no groove | 4.0mm2 | AWG 12 | 7.5mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSC∈ |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 12 |
| 依据 EN 61 984 的电气数据Electrical data according to EN 61984 | |
| -额定电流 Rated current | 10A |
| 额定电压 Rated voltage | 250V |
| 额定脉冲电压 Rated pulse voltage | 4kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 250V |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤1mΩ |
| 螺丝连接 Screw connection | |
| -mm2 | 0.14-2.5mm2 |
| -AWG | 26-14 |
弹片连接 Shrapnel connection
250V10A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
 | 公/Male | HMD-012-MS |
 | 母/Female | HMD-012-FS |
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHS Ce |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 17 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 |
| 一额定电流 Rated current 10A |
| -额定电压 Rated voltage 160V |
| -额定脉冲电压 Rated pulse voltage 2.5kV |
| -污染程度Pollution level 3 |
| 依据UL的额定电压250VRated voltage according to UL |
| 绝缘电阻 Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级According to UL 94 flame retardant rating Vo |
| 可拔插次数Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 镀金 Gild |
| 接触电阻 Contact resistance ≤3mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.14-2.5mm2 |
| -AWG 26-14 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN 60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
| 工具/Tool | 压接线经/Press wire | 型号/Type | 当线规小于0.75mm²时，建议使用辅助装针工具TL15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15 |
 退针器 | 0.37-4mm2 | CRIMPBOX- 0.5/4 | |
| 适用类型/Applicable type | 型号/Type | ||
| 10A 冷压针 Cold press needle | 注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the REMOV-HD product, please choose our special tool. |
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | |
尺寸图/Drawing   | |||
U | 公/Male | HMDD-017-MC | |
L | 母/Female | HMDD-017-FC |
10A 冷压针 Crimp contacts
接触电阻/Contact resistance ≤3m Ω镀银/Silvering 镀金/Gild | |||||||
| 公/Male | 母/Female | ||||||
尺寸图/DrawingM   | |||||||
| CDSM-0.25 | CDSF-0.25 | ||||||
| CDSM-0.37 | CDSF-0.37 | ||||||
| CDSM-0.50 | CDSF-0.50 | ||||||
| CDSM-0.75 | CDSF-0.75 | ||||||
| CDSM-1.0 | CDSF-1.0 | ||||||
| CDSM-1.5 | CDSF-1.5 | ||||||
| CDSM-2.5 | CDSF-2.5 | ||||||
| 线规 Wire gague | φ | 剥线长度 Stripping length | |||||
| CDGM-0.25 | CDGF-0.25 | ||||||
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm | ||||
| CDGM-0.37 | CDGF-0.37 | ||||||
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm | ||||
| CDGM-0.50 | CDGF-0.50 | ||||||
| 0.5mm2 | AWG 20 | 1.1 | 8mm | ||||
| CDGM-0.75 | CDGF-0.75 | ||||||
| 0.75mm2 | AWG 18 | 1.3 | 8mm | ||||
| CDGM-1.0 | CDGF-1.0 | 1mm2 | AWG 18 | 1.45 | 8mm | ||
| CDGM-1.5 | CDGF-1.5 | 1.5mm2 | AWG 16 | 1.75 | 8mm | ||
| CDGM-2.5 | CDGF-2.5 | 2.5mm2 | AWG 14 | 2.25 | 6mm | ||
技术参数 Technical parameter
规范/认证 Specification/Certification
规范/认证 Specification/Certification
| 规范 Norm DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication RoHSCe |
| 插芯 Core insert |
| 接插件针数 Pin number of connector 25 |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 |
| -额定电流 Rated current 4A |
| 额定电压 Rated voltage 50V |
| 额定脉冲电压 Rated pulse voltage 0.5kV |
| -污染程度Pollutionlevel 3 |
| 绝缘电阻Insulation resistance ≥10^{°Ω |
| 材料 Materials 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range -40℃...+125℃ |
| 依据UL 94 的阻燃等级voAccording to UL 94 flame retardant rating |
| 可拔插次数 Removable number of times ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜合金 Copper alloy |
| 表面处理 Surface treatment 镀银 Silvering |
| 镀金 Gild |
| 接触电阻 Contact resistance ≤3mΩ |
| 螺丝连接 Screw connection |
| -mm2 0.09-0.52mm2 |
| -AWG 28-20 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN 60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512–5
24B外壳带6个模块，导线截面:0.5mm²(车削针) 24B housing with 6 modules, wire cross section: 1.5mm2 (Turning needle)
冷压连接 Cold-pressed connection
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||
 | 公/Male | HMDS-025-MC | M |   | |
 | 母/Female | HMDS-025-FC |  |  | |
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
5A 冷压针 Crimp contacts
| a | b | c | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 工具/Tool | 压接线经/Press wire | 型号/Type |
冷压钳 Cold press pliers  | 0.09-0.82mm2 | TL03 |
| 适用类型/Applicable type | 型号/Type | |
退针器  Needle extractor | 5A 冷压针 Cold press needle | REMOV-HES |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 36 |
| 依据EN 61 984的电气数据 Electrical data according to EN 61984 | |
| 一额定电流 Rated current | 4A |
| -额定电压Rated voltage | 32V |
| 一额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤1mΩ |
| 螺丝连接 Screw connection | |
| -mm2 | 0.09-0.52mm2 |
| -AWG | 26-22 |
冷压连接 Cold-pressed connection
32V 4A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HMDS-036-MC |  |
 | 母/Female | HMDS-036-FC |  |
5A 冷压针 Crimp contacts
| a | b | C | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 42 |
| 依据EN 61984的电气数据Electrical data according to EN 61984 | |
| -额定电流 Rated current | 10A |
| 一额定电压 Rated voltage | 150V |
| -额定脉冲电压 Rated pulse voltage | 2.5kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | 250V |
| 绝缘电阻Insulation resistance | ≥10^°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金Gilding | |
| 接触电阻 Contact resistance | ≤3mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm2 | 0.14-2.5mm2 |
| -AWG | 26-14 |
冷压连接 Cold-pressed connection
150V 10A
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | H2MDD-042-MC |   |
10A 冷压针 Crimp contacts
接触电阻/Contact resistance ≤3m Ω 镀金/Gild | 公/Male | 母/Female |
| CDSM-0.25 | CDSF-0.25 | |
| CDSM-0.37 | CDSF-0.37 | |
| CDSM-0.50 | CDSF-0.50 | |
| CDSM-0.75 | CDSF-0.75 | |
| CDSM-1.0 | CDSF-1.0 | |
| CDSM-1.5 | CDSF-1.5 | |
| CDSM-2.5 | CDSF-2.5 | |
| CDGM-0.25 | CDGF-0.25 | |
| CDGM-0.37 | CDGF-0.37 | |
| CDGM-0.50 | CDGF-0.50 | |
| CDGM-0.75 | CDGF-0.75 | |
| CDGM-1.0 | CDGF-1.0 | |
| CDGM-1.5 | CDGF-1.5 | |
| CDGM-2.5 CDGF-2.5 | ||
 | 压接线经/Press wire | 型号/Type |
| 0.37-4mm2 | CRIMPBOX-0.5/4 | |
| 适用类型/Applicable type | 型号/Type | |
| 10A 冷压针Cold press needle | REMOV-HD | |
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm |
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm |
| 0.5mm2 | AWG 20 | 1.1 | 8mm |
| 0.75mm2 | AWG 18 | 1.3 | 8mm |
| 1mm2 | AWG 18 | 1.45 | 8mm |
| 1.5mm2 | AWG 16 | 1.75 | 8mm |
| 2.5mm2 | AWG 14 | 2.25 | 6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | |||
 | 公/Male | HM-USB-M |  | |||
 | 母/Female | HM-USB-F |  | |||
| 产品外观/Appearance | 描述/Describe | 型号/Type | 尺寸图/Drawing | |||
 | 用于填充固定 框架内空余的 模块空间 Used to fill the spare module space in the fixed frame | HM-000 |  | |||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 4 |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | |
| 额定电流Rated current | 1A |
| -额定电压 Rated voltage | 50V |
| 额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压 Rated voltage according to UL | < 30V |
| 绝缘电阻Insulation resistance | ≥10^°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+85℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | VO |
| 可拔插次数 Removable number of times | ≥500 |
用于接电缆 For connecting cables
50V 1A
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 8 |
| 依据EN 61 984的电气数据 Electrical data according to EN 61984 | |
| 一额定电流Rated current | 1A |
| 一额定电压 Rated voltage | 50V |
| 一额定脉冲电压Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL的额定电压Rated voltage according to UL | < 30V |
| 传输特性Transmission characteristic | 超6类可达 500MHz Super class 6 can be reached 500MHz |
| 依据 Basis ISO/IEC 24 702 | |
| ISO/IEC 11 801 | |
| 传输速率 Transmission rate | 10/100/1000Mbit/10Gbit/s |
| 绝缘电阻 Insulation resistance | ≥10^{1°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
插芯 用于接缆线 The plug is used to connect cables
50V1A
公插芯仅适用于高结构上壳，可与框架及其他所有模块产品组合使用Male insert is only suitable for high structure upper shell, Can be combined with framework and all other module products
尺寸图/Drawing  尺寸图/Drawing | ||||
| 产品外观/Appearance | 插芯/Insert | 型号/Type | ||
 | 公/Male | HM-RJ45-M | ||
 | 母/Female | HM-RJ45-F | ||
| 适配器/Adapter | 描述/Description | |||
 | 与公插芯搭配仅用于标准电缆接线It is matched with a public insertFor standard cable wiring only与公插芯搭配：HM-RJ45-M/APT/2With the male core: HM-RJ-M/APT/2 | |||
| 适配器/Adapter | 描述/Description | 型号/Type | 尺寸图/Drawing | |
M | 与公插芯搭配仅用于标准电缆接线It is matched with a public insertFor standard cable wiring only与公插芯搭配：HM-RJ45-M/APTWith the male core: HM-RJ-M /APT | HM-RJ45-APT | ||
技术参数 Technical parameter
规范/认证 Specification/Certification
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 9 |
| 依据 EN 61 984的电气数据 Electrical data according to EN 61984 | |
| 一额定电流 Rated current | 5A |
| -额定电压 Rated voltage | 50V |
| 额定脉冲电压 Rated pulse voltage | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻 Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤3mΩ |
| 螺丝连接 Screw connection | |
| -mm2 | 0.09-0.52mm2 |
| -AWG | 26-22 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
0.09-0.82mm2
d e s plers
冷压连接 Cold-pressed connection
50V 1A
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | ||||
 | 公/Male | HMDS/2.1-009-MC |  | ||||
 | 母/Female | HMDS/2.1-009-FC |  | ||||
50V1A
冷压连接 Cold-pressed connection
产品外观/Appearance
公/Male
母/Female
型号/Type
HMDS/2.1-009-MC 3SP01
HMDS/2.1-009-FC 3SP01
5A 冷压针 Crimp contacts
型号/Type
退针器 Needle extractor
型号/Type
5A 冷压针 Cold press needle
尺寸图/Drawing
| a | b | c | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 2 |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+80℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 聚甲醛 polyformaldehyde |
| 颜色 Colour | 黑色 Black |
| 软管连接 Hose connection | |
| -内径Insidediameter | 6.0mm / 1/4 " |
| 工作压力 Working pressure | 最大 Max 8 bar/116 psi |
| 密封圈 Sealing ring | |
| -材料 Materials | 氟橡胶 Fluororubber |
| 闭锁阀 Holding valve | |
| -材料 Materials | 聚甲醛 polyformaldehyde |
气动模块 Pneumatic module
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
插芯/Insert
尺寸图/Drawing
HMP-002
型号/Type
针 用于气管内径(ID) Needle for trachea bore ID
公/Male
无锁止 lock-free
(ID:6.0mm)
PCM-6.0
母/Female
无锁止lock-free
(ID:6.0mm)
PCF-6.0
针用于气管内径(ID) Needle for trachea bore ID
母/Female
带锁止 Tape locking
(ID:6.0mm)
PCFS-6.0
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 3 |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+80℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 聚甲醛 polyformaldehyde |
| 颜色 Colour | 黑色 Black |
| 软管连接 Hose connection | |
| -内径Insidediameter | 6.0mm/ 1/4" 3.0mm 4.0mm/1/8 " |
| 工作压力 Working pressure | 最大 Max 8 bar/116 psi |
| 密封圈 Sealing ring | |
| -材料 Materials | 氟橡胶 Fluororubber |
| 闭锁阀 Holding valve | |
| -材料 Materials | 聚甲醛 polyformaldehyde |
气动模块 Pneumatic module
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 针/ The needle | 描述/Description | 型号/Type | 尺寸图/Drawing | |||||
| 针用于气管内径(ID) Needle for trachea bore ID | 公/Male | |||||||
| 1 | 无锁止lock-free (ID:6.0/3.0/4.0mm) | PCM-1.6 PCM-3.0 | 1.6 |  |  | |||
| PCM-4.0 | ||||||||
 | 3.0 |  | ||||||
 | ||||||||
| 母/Female 无锁止lock-free (ID:6.0/3.0/4.0mm) | ||||||||
| PCF-1.6 | 4.0 | |||||||
| PCF-3.0 |  | |||||||
| 针用于气管内径(ID) Needle for trachea bore ID | 母/Female 带锁止 Tape locking | PCF-4.0 | ||||||
| PCFS-1.6 | ||||||||
二  |  | |||||||
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCE |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 3 |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+80℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜 Copper |
| 颜色 Colour | 镀镍 Nickel plating |
| 软管连接 Hose connection | |
| 一外径Outside diameter | 3.0mm / 4.0mm /6.0mm |
| 工作压力 Working pressure | 最大 Max 10 bar/145 psi |
| 密封圈 Sealing ring | |
| -材料Materials | 氟橡胶 Fluororubber |
| 闭锁阀 Holding valve | |
| -材料Materials | 聚甲醛polyformaldehyde |
金属气动针模块 Metal pneumatic needle module
可与框架及其他所有模块产品组合使用，匹配高结构外壳Can be combined with framework and all other module products, Match the high structure housing
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
B  | HMP-003-V2 |  |
| OD | φA | B | C | D |
| 3.0 | 8 | 43.7 | 8 | 48 |
| 4.0 | 9.8 | 43.9 | 9.8 | 50.2 |
| 6.0 | 9.8 | 45.9 | 9.8 | 52.2 |
| 工具/Tool | 适用范围/Scope of application | 型号/Type |
退针器 一 Needle extracto  | HMP-003-V2 金属气动针模块 Metal pneumatic needle module | TL26 |
| OD | φA | B | C | D |
| 3.0 | 8 | 7.1 | 34.8 | 48 |
| 4.0 | 9.8 | 7.1 | 36.8 | 50.2 |
| 6.0 | 9.8 | 9.1 | 36.8 | 52.2 |
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCE |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 3 |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+80℃ |
| 依据UL 94 的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin |
| 材料 Materials 铜 Copper |
| 颜色 Colour 镀镍 Nickel plating |
| 软管连接 Hose connection |
| -内径Insidediameter 3.0mm/ 4.0mm / 6.0mm |
| 工作压力 Working pressure 最大 Max 10 bar/145 psi |
| 密封圈 Sealing ring |
| -材料 Materials 氟橡胶 Fluororubber |
| 闭锁阀 Holding valve |
| -材料 Materials 聚甲醛 polyformaldehyde |
金属气动针模块 Metal pneumatic needle module
| 可与框架及其他所有模块产品组合使用，匹配高结构外壳 Can be combined with framework and all other module products, Match the high structure housing | ||||
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing | |
 | HMP-003-V2 |  | ||
| 针/ The needle 金属气动针 | 描述/Description | 型号/Type | 尺寸图/Drawing | |
用于气管外径(OD) Pneumatic metal needle For trachea OD  | 公/Male 无锁止 lock-free (ID:3.0/4.0/6.0mm) | MPCM-OD3.0 | M(3.0) Do P3 | |
| MPCM-OD4.0 | -37.6 M(4.0) | |||
| 母/Female 无锁止lock-free (ID:3.0/4.0/6.0mm) | MPCM-OD6.0 | 41.3 07 | ||
| MPCF-OD3.0 | M(6.0) | |||
| MPCF-OD4.0 | 40.2 7.9 | |||
| MPCF-OD6.0 | F(3.0) | |||
| MPCMS-OD6.0 | 36.5 F(4.0) | |||
| 母/Female MPCFS-OD3.0 带锁止 Tape locking | 40.2 F(6.0) | |||
| (ID:6.0/3.0/4.0/6.0mm) MPCFS-OD4.0 | 39.1 | |||
| MPCFS-OD6.0 | M(6.0) | 38.5 | ||
| -(42) | ||||
| ε | ||||
| 工具/Tool 适用范围/Scope of application 退针器 HMP-003-V2 Needle extractor 金属气动针模块 TL26 Metal pneumatic needle module | 型号/Type | |||
| F(3.0) | ||||
| 7.9 | ||||
| 36.6 | ||||
| F(4.0) | ||||
 | ||||
| F(6.0) | 09  | |||
SUZHOU XIBASHI Provide a total solution for electrical connections! 苏州西霸士为电气连接提供整体解决方案!
技术参数 Technical parameter
| 规范/认证Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 2+PE |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | |
| -额定电流 Rated current | 40A |
| -额定电压Rated voltage | 830V |
| -额定脉冲电压 Rated pulse voltage | 6kV |
| -污染程度Pollutionlevel | 3 |
| 依据UL/CSA的额定电压 Rated voltage according to UL/CSA | 600V |
| 绝缘电阻Insulation resistance | ≥10{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 接触电阻 Contact resistance | ≤1mΩ |
| 轴向螺栓连接 Axial bolted connection | |
| -mm2 | 2.5-10mm2 |
| -AGW | 14-8 |
| 拧紧力矩 Tightening moment | 1.8Nm |
| 剥线长度 Strip length | 8mm^+ |
| 外壳 Shell | |
| Plastic case | |
| -材料 Materials | 聚碳酸酯 Polycarbonate |
| -依据UL94的阻燃等级 According to UL 94 flame retardant rating | VO |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65 |
| □□Metal case | |
| -材料 Materials | 锌合金 Zinc alloy |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65/IP68 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接插氏的接插体可承受的最大温度
测试和控制过程依据DINEN60512-5
The current load capacity is limited mainly by the inclusion connection The maximum temperature that the plug can withstand The test and control procedures are in accordance with DIN EN 60512-5
导线截面: 10mm²
Traverse section: 10mm2
导线截面: 6mm² Traverse section: 6mm
导线截面: 4mm² Traverse section: 4mm
导线截面: 2.5mm² Traverse section: 2.5mm
轴向螺栓连接/带耐压热缩管Axial bolted connection/With pressure resistant heat shrink tube
外壳尺寸：匹配H3A外壳，详情参考175-230页 Hoods/Housings:Matching H3A Hood Housing,detail on P175-230
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
朝  | 公/Male | HQ-002.1-M (2.5-6.0mm²) HQ-002.2-M (4-10mm2) |   |
4  | 母/Female | HQ-002.1-F (2.5-6.0mm2) HQ-002.2-F (4-10mm2) |   |
附件 Attachments
| 工具/Tool | 描述/Description | 型号/Type | |
| 内六角扳手/Hex key | 用于轴向夹紧螺栓带T型把手Used for axial clamping boltsWith a T-handle | SW-2*100 | |
| 编码元件/Coding element | 描述/Description | 型号/Type | 尺寸图/Drawing日30 □4.3 |
 | 编码、防呆Coding, anti-dork | CODE-Q2 |
HQ-002比HQV-002增加了耐压热缩管，增加了绝缘性能，提高额定电压。
Compared with HQV-002, HQ-002 adds a pressure-resistant heat shrink tube, increases the insulation performance, and improves the rated voltage.
Compared with HQV-002, HQ-002 adds a pressure-resistant heat shrink tube, increases the insulation performance, and improves the rated voltage.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHS Ce |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 5+PE |
| 依据 EN 61 984 的电气数据 Electrical data according to EN 61984 | |
| -额定电流 Rated current | 16A |
| -相对地额定电压Rated voltage relative to ground | 230V |
| -相间额定电压Phase rated voltage | 400kV |
| -额定脉冲电压Rated pulse voltage | 4kV |
| -污染程度Pollutionlevel | 3 |
| -当污染等级2时的参数Parameter when pollution level2 | 16A 320/500V 4kV 2 |
| 依据UL/CSA的额定电压 Rated voltage according to UL/CSA | 600V |
| 绝缘电阻 Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range 依据UL 94的阻燃等级 | -40℃...+125℃ |
| According to UL 94 flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin 材料 Materials | |
| 铜合金 Copper alloy | |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤1mΩ |
| 冷压连接Cold-pressed connection | |
| -mm2 | 0.14-4.0mm2 |
| -AGW | 26-14 |
| PE螺钉连接PE screw connection | |
| -mm2 | 2.5mm2 |
| -AGW | 14 |
| 外壳 Shell | |
| Plastic case | |
| -材料 Materials | 聚碳酸酯 Polycarbonate |
| -依据UL 94的阻燃等级 According to UL 94 flame retardant rating | vo |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65 |
| Metal case | |
| -材料 Materials | 锌合金 Zinc alloy |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65/IP68 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
导线截面: 2.5mm² Traverse section: 2.5mm
导线截面: 1.5mm² Traverse section: 1.5mm
导线截面: 1.0mm² Traverse section:1.5mm
外壳尺寸：匹配H3A外壳，详情参考175-230页 Hoods/Housings:Matching H3A Hood Housing,detail on P175-230
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
| 公/Male | HQ-005/0-MC | 39.5 30.8 27 | |
| 母/Female | HQ-005/0-FC | # 21 -31.5 |
16A 冷压针 Crimp contacts
| 标示 Identification | 线规 Wire gague | 剥线长度 Stripping length | |
| no groove | 0.14-0.37mm2 | AWG 26-22 | 7.5mm |
| no groove | 0.5mm2 | AWG 20 | 7.5mm |
| 1 groove | 0.75mm2 | AWG 18 | 7.5mm |
| 1 groove | 1.0mm2 | AWG 18 | 7.5mm |
| 2 groove | 1.5mm2 | AWG 16 | 7.5mm |
| 3 groove | 2.5mm2 | AWG 14 | 7.5mm |
| wide groove | 3.0mm2 | AWG 12 | 7.5mm |
| no groove | 4.0mm2 | AWG 12 | 7.5mm |
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。
Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCE |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 7+PE |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | |
| -额定电流Rated current | 10A |
| 一相对地额定电压Rated voltage relative to ground | 400V |
| 一额定脉冲电压Rated pulse voltage | 6kV |
| -污染程度Pollutionlevel | 3 |
| -当污染等级2时的参数Parameter when pollution level2 | 10A 400/690V 6kV 2 |
| 依据UL/CSA的额定电压 Rated voltage according to UL/CSA | 600V |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围 Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤ 3mΩ |
| 冷压连接Cold-pressed connection | |
| -mm^2 | 0.14-2.5mm2 |
| -AGW | 26-14 |
| PE 螺钉连接 PE screw connection | |
| -mm^2 | 2.5mm2 |
| -AGW | 14 |
| 外壳 Shell | |
| 塑料外壳 Plastic case | |
| -材料 Materials | 聚碳酸酯 Polycarbonate |
| -依据UL94的阻燃等级 According to UL 94 flame retardant rating | vo |
| -联锁状态下依据 DIN Interlocked according to DIN | |
| -EN60 529的防护等级 Level of protection | IP65 |
| 金属外壳 Metal case | |
| -材料 Materials | 锌合金 Zinc alloy |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60 529 的防护等级 Level of protection | IP65/IP68 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
导线截面: 2.5mm² Traverse section: 2.5mm
导线截面: 0.75mm² Traverse section: 0.75mm 导线截面: 1.5mm² Traverse section: 1.5mm
| 编码元件/Coding element | 描述/Description | 型号/Type |
冷压连接 Cold-pressed connection
400V 10A 7+
外壳尺寸：匹配H3A外壳，详情参考175-230页 Hoods/Housings:MatchingH3A Hood Housing,detail on P175-230
| 产品外观/Appearance | 插芯/Insert | 型号/Type | 尺寸图/Drawing |
 | 公/Male | HQ-007/0-MC |  |
 | 母/Female | HQ-007/0-FC |
10A 冷压针 Crimp contacts
| 公/Male | 母/Female |
| CDSM-0.25 | CDSF-0.25 |
| CDSM-0.37 | CDSF-0.37 |
| CDSM-0.50 | CDSF-0.50 |
| CDSM-0.75 | CDSF-0.75 |
| CDSM-1.0 | CDSF-1.0 |
| CDSM-1.5 | CDSF-1.5 |
| CDSM-2.5 | CDSF-2.5 |
| CDGM-0.25 | CDGF-0.25 |
| CDGM-0.37 | CDGF-0.37 |
| CDGM-0.50 | CDGF-0.50 |
| CDGM-0.75 | CDGF-0.75 |
| CDGM-1.0 | CDGF-1.0 |
| CDGM-1.5 | CDGF-1.5 |
| CDGM-2.5 | CDGF-2.5 |
| CRIMPBOX- | |
| 0.37-4mm² | 0.5/4 |
| 适用类型/Applicable type | 型号/Type |
10A 冷压针 REMOV-HD Cold press needle
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm |
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm |
| 0.5mm^2 | AWG 20 | 1.1 | 8mm |
| 0.75mm2 | AWG 18 | 1.3 | 8mm |
| 1mm2 | AWG 18 | 1.45 | 8mm |
| 1.5mm2 | AWG 16 | 1.75 | 8mm |
| 2.5mm2 | AWG 14 | 2.25 | 6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
| 编码 Coding | 公/Male | CODE-Q7M |
| 防呆 anti-dork | 母/female | CODE-Q7F |
技术参数 Technical parameter
| 规范/认证 Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数 Pin number of connector | 12+PE |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | |
| -额定电流Ratedcurrent | 10A |
| 一相对地额定电压Rated voltage relative to ground | 400V |
| 一额定脉冲电压Rated pulse voltage | 6kV |
| 一污染程度Pollutionlevel | 3 |
| -当污染等级2时的参数Parameter when pollution level2 | 10A 400/690V 6kV 2 |
| 依据UL/CSA的额定电压 Rated voltage according to UL/CSA | 600V |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围 Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | vo |
| 可拔插次数 Removable number of times | ≥500 |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤ 3mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm2 | 0.14-2.5mm2 |
| -AGW | 26-14 |
| PE 螺钉连接 PE screw connection | |
| -mm2 | 0.5-2.5mm² |
| -AGW | 20-14 |
| 外壳 Shell | |
| Plastic case | |
| -材料 Materials | 聚碳酸酯 Polycarbonate |
| -依据UL 94的阻燃等级 According to UL 94 flame retardant rating | vo |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65 |
| Metal case | |
| -材料 Materials | 锌合金 Zinc alloy |
| -联锁状态下依据DIN Interlocked according to DIN | |
| -EN60529Level of protection | IP65/IP68 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
导线截面: 2.5mm² Traverse section: 2.5mm
导线截面: 1.5mm2 Traverse section: 1.5mm
导线截面: 0.75mm² Traverse section: 0.75mm
| 编码、防呆 | CODE-Q12 |
冷压连接 Cold-pressed connection
400V 10A 12+
外壳尺寸：匹配H3A外壳，详情参考175-230页 Hoods/Housings:Matching H3A Hood Housing,detail on P175-230
| 产品外观/Appearance | 插芯/Insert | 型号/Type |
尺寸图/Drawing  | ||
 | 公/Male | HQ-012/0-MC |
 | 母/Female | HQ-012/0-FC |
10A 冷压针 Crimp contacts
| 公/Male | 母/Female |
| CDSM-0.25 | CDSF-0.25 |
| CDSM-0.37 | CDSF-0.37 |
| CDSM-0.50 | CDSF-0.50 |
| CDSM-0.75 | CDSF-0.75 |
| CDSM-1.0 | CDSF-1.0 |
| CDSM-1.5 | CDSF-1.5 |
| CDSM-2.5 | CDSF-2.5 |
| CDGM-0.25 | CDGF-0.25 |
| CDGM-0.37 | CDGF-0.37 |
| CDGM-0.50 | CDGF-0.50 |
| CDGM-0.75 | CDGF-0.75 |
| CDGM-1.0 | CDGF-1.0 |
| CDGM-1.5 | CDGF-1.5 |
| CDGM-2.5 | CDGF-2.5 |
| 压接线经/Press wire | 型号/Type |
| CRIMPBOX- | |
| 0.37-4mm2 | 0.5/4 |
| 适用类型/Applicable type | 型号/Type |
| 线规 Wire gague | ① | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 0.65 | 5mm |
| 0.14-0.37mm2 | AWG 26-22 | 0.9 | 8mm |
| 0.5mm^2 | AWG 20 | 1.1 | 8mm |
| 0.75mm2 | AWG 18 | 1.3 | 8mm |
| 1mm2 | AWG 18 | 1.45 | 8mm |
| 1.5mm2 | AWG 16 | 1.75 | 8mm |
| 2.5mm2 | AWG 14 | 2.25 | 6mm |
当线规小于0.75mm²时，建议使用辅助装针工具TL15 When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
| 10A 冷压针 | |
| Cold press needle | REMOV-HD |
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
| 描述/Description | 型号/Type |
技术参数 Technical parameter
| 规范/认证Specification/Certification | |
| 规范 Norm | DIN EN 60 664 DIN EN 61 984 |
| 认证 Authentication | RoHSCe |
| 插芯 Core insert | |
| 接插件针数Pin number of connector | 10+RJ45 |
| 依据EN 61 984的电气数据Electrical data according to EN 61984 | |
| 一额定电流 Rated current | |
| -电力区 Power area | 5A |
| -信号区Signal area | 1A |
| 一额定电压Rated voltage | 50V |
| -污染程度Pollution level | 0.8kV |
| -污染程度Pollutionlevel | 3 |
| 绝缘电阻Insulation resistance | ≥10^{°Ω |
| 材料 Materials | 聚碳酸酯 Polycarbonate |
| 工作温度范围Operating temperature range | -40℃...+125℃ |
| 依据UL 94的阻燃等级 According to UL 94 flame retardant rating | Vo |
| 可拔插次数 Removable number of times | ≥500 |
| 传输特性 Transmission characteristics | 10/100/1000Mbit/10Gbot/s |
| 插针 Inserting pin | |
| 材料 Materials | 铜合金 Copper alloy |
| 表面处理 Surface treatment | 镀银 Silvering |
| 镀金 Gild | |
| 接触电阻 Contact resistance | ≤3mΩ |
| 冷压连接 Cold-pressed connection | |
| -mm² | 0.09-0.52mm2 |
| -AGW | 28-20 |
电流负载能力 Current load capacity
电流负载能力所受的限制主要来自包含接
插氏的接插体可承受的最大温度
测试和控制过程依据DIN EN60512-5
The current load capacity is limited mainly by the inclusion connection
The maximum temperature that the plug can withstand
The test and control procedures are in accordance with DIN EN 60512-5
冷压连接 Cold-pressed connection
可与框架及其他所有模块产品组合使用Can be combined with framework and all other module products
| 产品外观/Appearance | 插芯/Insert | 型号/Type | |
尺寸图/DrawingM  2.9×9.5F  | |||
一 | 公/Male | $H Q - P J 4 5 / 1 0 - M C$ | |
山 | 母/Female | $H Q - B J 4 5 / 1 0 - F C$ |
5A 冷压针 Crimp contacts
| 工具/Tool | 压接线经/Press wire | 型号/Type |
冷压钳 Cold press pliers K  | $0 . 0 9 - 0 . 8 2 m m ^ { 2 }$ | TL03 |
| 适用类型/Applicable type | 型号/Type | |
| 退针器 Needle extractor | 5A 冷压针 Cold press needle | REMOV-HES |
| a | b | c | d | e | f |
| 8.10 | 4.0 | 14.8 | 0.64 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 0.90 | 1.66 | 14.4 |
| 8.10 | 4.0 | 14.8 | 1.12 | 1.66 | 14.4 |
| 线规 Wire gague | 剥线长度 Stripping length | |
| 0.09-0.25mm2 | AWG 28-24 | 5mm |
| 0.13-0.33mm2 | AWG 26-22 | 5mm |
| 0.33-0.52mm2 | AWG 22-20 | 5mm |
When the cable gauge is smaller than 0.75mm2, you are advised to use an auxiliary needle mounting tool TL15
注意事项:冷压压接工具关系产品的质量稳定性，请选择我司专用工具。 Note: The cold pressing crimping tool is related to the quality and stability of the product, please choose our special tool.
用于将连接体横向固定在常用的标准导轨上 It is used to fix the connector horizontally on the common standard guide rail
产品外观/AppearanceA款/Paragraph | 规格Specification | |||||||
| 6B | ||||||||
| 10B | ||||||||
| 规格/Specification | A | B | C | D | E | F | ||
| 6B | 30.2 | 46.8 | 27 | 43 | 44 | 59 | ||
| 10B | 43.2 | 59.8 | 27 | 43 | 57 | 72 | ||
| 16B | 63.7 | 80.3 | 27 | 43 | 77.5 | 92.5 | ||
| 24B | 90.2 | 106.8 | 27 | 43 | 104 | 119 | ||
装配示意图Assembly diagram
A款/Paragraph
用于将不封底下壳固定在常用的标准导轨上 It is used to fix the unsealed lower shell on the commonly used standard guide rai
| 规格Specification | 型号/Type | |||||||||
| 6B | ||||||||||
| 10B | ||||||||||
| 16B | CC16B-BK | |||||||||
| 规格/Specification | A | B | C | D | E | F | G | H | ||
| 6B | 70 | 44 | 32 | 27 | 87.3 | 64.4 | 125 | 55 | ||
| 10B | 83 | 57 | 32 | 27 | 87.3 | 64.4 | 125 | 55 | ||
| 16B | 103 | 77.5 | 32 | 27 | 87.3 | 64.4 | 125 | 55 | ||
| 24B | 130 | 104 | 32 | 27 | 87.3 | 64.4 | 150 | 54.5 | ||
用于将连接体横向固定在常用的标准导轨上，可调节型导轨支架
It is used to fix the connector horizontally on the common standard guide rail, and the adjustable guide rail bracket
| B款 导轨支架/B type guide rail support | 型号/Type | ||||||||
| 适用于所有可 CRITI | |||||||||
| 描述Description | |||||||||
| 规格/Specification | A | B | C | D | E | F | |||
| 6B | 30.2 | 46.8 | 27 | 43 | 44 | 59 | |||
| 10B | 43.2 | 59.8 | 27 | 43 | 57 | 72 | |||
| 16B | 63.7 | 80.3 | 27 | 43 | 77.5 | 92.5 | |||
| 24B | 90.2 | 106.8 | 27 | 43 | 104 | 119 | |||
装配示意图 Assembly diagram
可调节活动底座 Adjustable adjustable base
①匹配适用于6B型外壳的插芯和6B模块框架
②匹配适用于10B型外壳的插芯和10B模块框架
③匹配适用于16B型外壳的插芯和16B模块框架
④匹配适用于24B型外壳的插芯和24B模块框架
产品外观/Appearance
用编码销编号 Number with a coded pin
产品外观/Appearance
用导向销和导向孔编号 umber with guide pins and guide holes
CODING-PIN-M3-M
尺寸图/Drawing
尺寸图/Drawing
CODING-PIN-M3-F
M
M
M
对接架Butt stand
| 规格 Specification | 型号/Type |
| 6B | H6B-ADK |
| 10B | H10B-ADK |
| 16B | H16B-ADK |
| 24B | H24B-ADK |
技术参数
Technical parameter
材料
Materials
-对接架
-Docking rack
-固定螺栓
-Fixing bolts
插入容差
Insertion tolerance
-x轴
-x axis
-Y轴
-Y axis
拔插次数
Number of insertions 不锈钢
Stainless steel 铁，镀锌
Iron, galvanized
±1.5mm
±1.5mm
≥500
尺寸图/Drawing
安装开口 Mounting opening
1）距离电气针和光线电缆针距离最大27mm
气动针距离最大26.5mm
1) The maximum distance from the electrical needle and the light cable needle is 27mm
Pneumatic needle distance maximum 26.5mm
产品包括 Products include
1个架子 Shelf
4个带平头的螺栓，用于固定对接架
Four bolts with flat heads for securing the butt frame
| 规格/Specification | a | b | c | d | e |
| 6B | 86 | 69 | 69 | 54.5 | 84 |
| 10B | 99 | 82 | 82 | 67.5 | 97 |
| 16B | 119.5 | 102.5 | 102.5 | 88 | 117.5 |
| 24B | 146 | 129 | 129 | 114.5 | 144 |
退针器/Remove  | ||
| 型号/Type | 适用范围 Application Scope | |
| CRIMPBOX-0.5/4 | 0.5-4.0mm冷压针0.5-4.0mm Cold Pressing Needle | |
| REMOV-HD | 10A冷压针10A Cold Pressing Needle | |
 | REMOV-HEE | 16A冷压针16A Cold Pressing Needle |
 | REMOV-HES | 弹片压接的弹片针Shrapnel pin pressed by shrapnel |
 REMOV-MM | 40A冷压针40A Cold Pressing Needle | |
SUZHOU XIBASHI Provide a total solution for electrical connections! 苏州西霸士为电气连接提供整体解决方案!
H3A系列外壳(金属)Series housing(metal)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳 顶部出线/Upper shell top outlet line | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG11 | H3A-MTG-PG11  |  |
| 上壳侧面出线/Upper shell side outlet | M20 | H3A-MTG-M20 | 尺寸图/Drawing |
 | 螺纹/Thread PG11 | 型号/Type H3A-MTS-PG11 | |
| 不封底下壳/Unsealed bottom shell |   | ||
| M20 螺纹/Thread | $H _ { 3 } A - M T S - M _ { 2 } O$ 型号/Type | 尺寸图/Drawing | |
 |   |
H3A系列外壳(金属)Series housing(metal)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 面板安装(侧出形式)/Open bottom shell | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | H3A-MAGS |   | |
| 表面安装(侧面形式)/Bottom shell (side form) | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG11 | H3A-MAGSV-PG11 |  |
| PG11 | H3A-MTGVB-PG11 | ||
 |   | ||
| M20 | H3A-MTGVB-M20 |
H3A 系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 防护盖/Protective cover | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | H3A-MAD-M (配公芯) 1 H3A-MAD-F (配母芯) |   |  |
| 防护盖/Protective cover | 连接方式 Connection method | 型号/Type | 尺寸图/Drawing |
  防护盖/Protective cover |  | H3A-MCV-1L/1M (配公芯) | |
 | H3A-MCV-1L/1F (配母芯) |  尺寸图/Drawing | |
| 连接方式 Connection method | 型号/Type | ||
 |  | H3A-MCV-2B/1M (配公芯) | |
 | H3A-MCV-2B/2M (配公芯) | ||
 | H3A-MCV-2B/1F (配母芯) |  | |
| H3A-MCV-2B/2F | |||
 | (配母芯) |
H3A 系列外壳(塑料)Series housing(plastic)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 面板安装(侧出形式)/Open bottom shell | 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |||
 | H3A-AGS |   | ||||
| 表面安装(侧面形式)/Bottom shell (side form) | 螺纹/Thread | 型号/Type | ||||
 | PG11 | H3A-AGSV-PG11 |  | |||
| M20 | H3A-AGSV-M20 |  | ||||
| 电缆对接下壳/Cable butt bottom shell | 螺纹/Thread | 型号/Type | ||||
 | PG11 | H3A-TGVB-PG11 | ||||
| M20 | H3A-TGVB-M20 | |||||
H3A系列外壳(塑料)Series housing(plastic)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
上壳 顶部出线/Upper shell top outlet lineB | ||
| 螺纹/Thread | 型号/Type | |
| PG11 | ||
| M20 | ||
上壳侧面出线/Upper shell side outlet9 | 螺纹/Thread | 型号/Type |
| PG11 | ||
| 面板安装/Unsealed bottom shell | 螺纹/Thread | 型号/Type |
 | 7 | H3A-AG |
H10A系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳 侧面出线/Upper shell side outlet | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG13.5 | H10A-TS-2B-PG13.5 | |
| PG16 | H10A-TS-2B-PG16 |   | |
| M20 | H10A-TS-2B-M20 | ||
| 上壳侧面出线 高结构/Upper shell side outlet high structure | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG16 | H10A-TSH-2B-PG16 | |
| PG21 | H10A-TSH-2B-PG21 |   | |
| M25 | H10A-TSH-2B-M25 | 尺寸图/Drawing | |
| 上壳 顶部出线/Upper shell top outlet line | 螺纹/Thread | 型号/Type | |
 | PG13.5 | H10A-TG-2B-PG13.5 |   |
| PG16 | H10A-TG-2B-PG16 | ||
| M20 螺纹/Thread | H10A-TG-2B-M20 | 尺寸图/Drawing | |
| 上壳顶部出线高结构/Upper shell top outlet line high structure PG16 | 型号/Type H10A-TGH-2B-PG16 | ||
 | |||
| PG21 | H10A-TGH-2B-PG21 |   | |
| M25 | H10A-TGH-2B-M25 |
H10A 系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 面板安装/Unsealed bottom shell | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | 1 | H10A-AG-LB |   面板开孔图 |
| 面板安装 带盖/Unsealed lower shell with cover | 螺纹/Thread | 型号/Type | Panel cut out 尺寸图/Drawing |
 | H10A-AD-LB | ||
| 表面安装 高结构/Upper shell with high structure | 型号/Type | 尺寸图/Drawing | |
| PG13.5 1个进线孔 PG16 | H10A-SGR-LB-PG13.5 | ||
 | H10A-SGR-LB-PG16 | ||
| PG21 | H10A-SGR-LB-PG21 | ||
| M20 | H10A-SGR-LB-M20 | ||
| M25 | H10A-SGR-LB-M25 |  | |
| PG13.52个进线孔 | H10A-SGR-LB-2PG13.5 | ||
| PG16 | H10A-SGR-LB-2PG16 | ||
| PG21 | H10A-SGR-LB-2PG21 | ||
| M20 | H10A-SGR-LB-2M20 | ||
| M25 | H10A-SGR-LB-2M25 | ||
| 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
| 表面安装高结构带盖/Bac cover lowershll hig tructure with cover | PG13.5 1个进线孔 | H10A-SDR-LB-PG13.5 | |
| PG16 | H10A-SDR-LB-PG16 | ||
| PG21 | H10A-SDR-LB-PG21 | ||
| M20 | H10A-SDR-LB-M20 | ||
 | M25 | H10A-SDR-LB-M25 | |
| PG13.52个进线孔 |  H10A-SDR-LB-2PG13.5 | ||
| PG16 | H10A-SDR-LB-2PG16 | ||
| PG21 | H10A-SDR-LB-2PG21 | ||
| M20 M25 | H10A-SDR-LB-2M20 H10A-SDR-LB-2M25 |
H16A 系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳 侧面出线/Upper shell side outlet | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG13.5 | H16A-TS-2B-PG13.5 | |
| PG16 | H16A-TS-2B-PG16 |   | |
| M20 | H16A-TS-2B-M20 | ||
| 上壳侧面出线高结构/Upper hell side outlet high structure | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG16 | H16A-TSH-2B-PG16 | |
| PG21 | H16A-TSH-2B-PG21 |   | |
| M25 螺纹/Thread | H16A-TSH-2B-M25 型号/Type | 尺寸图/Drawing | |
| 上壳 顶部出线/Upper shell top outlet line | PG13.5 | H16A-TG-2B-PG13.5 | |
 上壳顶部出线高结构/Upper shell top outlet line high structure | PG16 | H16A-TG-2B-PG16 |   |
| M20 | H16A-TG-2B-M20 | ||
| 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
| PG16 | H16A-TGH-2B-PG16 | ||
 | PG21 | H16A-TGH-2B-PG21 |  |
 | |||
| M25 | H16A-TGH-2B-M25 | ||
H16A 系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 面板安装/Unsealed bottom shell | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | H16A-AG-LB |   面板开孔图 Panel cut out | |
| 面板安装 带盖/Unsealed lower shell with cover | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | H16A-AD-LB |   | |
| 表面安装 高结构/Upper shell with high structure | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | |||
| PG13.5 1个进线孔 | H16A-SGR-LB-PG13.5 | ||
| PG16 | H16A-SGR-LB-PG16 | ||
| PG21 | H16A-SGR-LB-PG21 | ||
| M20 | H16A-SGR-LB-M20 | ||
| M25 | H16A-SGR-LB-M25 |   | |
| PG13.5 2个进线孔 | H16A-SGR-LB-2PG13.5 | ||
| PG16 | H16A-SGR-LB-2PG16 | ||
| PG21 | H16A-SGR-LB-2PG21 | ||
| M20 | H16A-SGR-LB-2M20 | ||
| M25 | H16A-SGR-LB-2M25 | ||
| 螺纹/Thread 表面安装高结构带盖/Back cover lwer shel high truture with cover | 型号/Type | 尺寸图/Drawing | |
| PG13.51个进线孔 | H16A-SDR-LB-PG13.5 | ||
| H16A-SDR-LB-PG16 | |||
 | PG16 | ||
| PG21 | H16A-SDR-LB-PG21 | ||
| M20 | H16A-SDR-LB-M20 | ||
| M25 PG13.52个进线孔 | H16A-SDR-LB-M25 H16A-SDR-LB-2PG13.5 |   | |
| PG16 | H16A-SDR-LB-2PG16 | ||
| PG21 | H16A-SDR-LB-2PG21 | ||
| M20 | H16A-SDR-LB-2M20 | ||
| M25 | H16A-SDR-LB-2M25 |
H32A 系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳 侧面出线/Upper shell side outlet | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG21 | H32A-TS-PG21 | |
| PG29 | H32A-TS-PG29 | ||
| M25 | H32A-TS-M25 | ||
| M32 | H32A-TS-M32 | ||
| M40 | H32A-TS-M40 | ||
上壳 顶部出线 高结构 Upper shell top outlet line high structure  | 螺纹/Thread | 型号/Type | |
| PG21 | H32A-TG-PG21 | ||
| PG29 | H32A-TG-PG29 | ||
| M25 | H32A-TG-M25 | ||
| M32 | H32A-TG-M32 | ||
| M40 | H32A-TG-M40 | ||
| 面板安装/Unsealed bottom shell | 螺纹/Thread 型号/Type | 尺寸图/Drawing | |
 | H32A-AG |   |
H32A 系列外壳 Series housing
| 封底高座下壳/Upper shell with | 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
| PG21 1个进线孔 | H32A-SGR-PG21 |   尺寸图/Drawing   | ||
 | PG29 | H32A-SGR-PG29 | ||
| M25 | H32A-SGR-M25 | |||
| M32 | H32A-SGR-M32 | |||
| M40 | H32A-SGR-M40 | |||
| PG21 2个进线孔 | H32A-SGR-2PG21 | |||
| PG29 | H32A-SGR-2PG29 | |||
| M25 | H32A-SGR-2M25 | |||
| M32 | H32A-SGR-2M32 | |||
| M40 | H32A-SGR-2M40 | |||
| 塑料防护盖 4卡扣/Plastic protective cover 4 buckle | 连接方式 Connection method | 型号/Type | ||
 |  | H32A-KDT.1 | ||
 | ||||
 连接方式 | H32A-KDT.2 | |||
| 飞线下壳 高结构/Fly the outer shellHigh structure | Connection method | 型号/Type | 尺寸图/Drawing | |
 |  | H32A-KDB.1 | ||
 | 15 | |||
| H32A-KDB.2 | ||||
| 上壳侧出线带双扣/Upper shell side cable with double buckle | 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
 | PG21 | |||
| H32A-TSB-PG21 | ||||
| PG29 | ||||
| H32A-TSB-PG29 |  | |||
| M25 | H32A-TSB-M25 | |||
防护等级Protection grade: IP65
H32A系列外壳 Series housing
防护等级Protection grade: IP65
防护等级Protection grade: IP65
面板安装 4耳带盖/Unsealed lower shell ears with cover | ||||||||
| 螺纹/Thread | ||||||||
表面安装 4耳带盖/Back cover lower shell 4 ears with coverPGM PG | ||||||||
| 螺纹/Thread | 型号/Type | |||||||
| Pg21 1个进线孔 | H32A-SDR-4B-PG21 | |||||||
| 29 | H32A-SDR-4B-PG29 | |||||||
| 25 | H32A-SDR-4B-M25 | |||||||
| M32 | H32A-SDR-4B-M32 | |||||||
| PG21 2个进线孔 | H32A-SDR-4B-2PG21 | |||||||
| 29 | H32A-SDR-4B-2PG29 | |||||||
| M25 | H32A-SDR-4B-2M25 | |||||||
| M32 | H32A-SDR-4B-2M32 | |||||||
H6B系列外壳(单扣)Series housing(Single buckle)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳 侧面出线/Upper shell side outlet | 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
 | PG13.5 | H6B-TS-2B-PG13.5 | ||
| PG16 | H6B-TS-2B-PG16 |   | ||
| M20 | ||||
| 螺纹/Thread | H6B-TS-2B-M20 | |||
| PG21 | 型号/Type | 尺寸图/Drawing | ||
 | H6B-TSH-2B-PG21 | |||
| PG29 | H6B-TSH-2B-PG29 |   | ||
| M25 | H6B-TSH-2B-M25 | |||
| M32 | H6B-TSH-2B-M32 | 尺寸图/Drawing | ||
上壳 顶部出线/Upper shell top outlet line  | 螺纹/Thread | 型号/Type | ||
| PG13.5 | H6B-TG-2B-PG13.5 | |||
| PG16 | H6B-TG-2B-PG16 |  |  | |
| M20 | ||||
| H6B-TG-2B-M20 |
H6B系列外壳(单扣) Series housing (Single buckle)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 上壳顶部出线 高结构/Upper shell top outlet line high structure | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
| PG29 | H6B-TGH-2B-PG29 | ||
| PG21 | H6B-TGH-2B-PG21 | ||
  | |||
| M25 | H6B-TGH-2B-M25 | ||
| M32 | H6B-TGH-2B-M32 | ||
| 连接方式 Connection method | 型号/Type | ||
| 塑料防护盖/Plastic protective cover | 尺寸图/Drawing | ||
 | H6B-KDT.1 | ||
 |  |  | |
| 塑料防护盖/Plastic protective cover |  | H6B-KDT.2 | |
| 连接方式 Connection method | 型号/Type | 尺寸图/Drawing | |
 |  | H6B-KDB.1 | |
 | |||
 | H6B-KDB.2 | ||
| 面板安装/Unsealed bottom shell | |||
| 螺纹/Thread | 型号/Type | ||
| 尺寸图/Drawing | |||
  | |||
 | |||
| H6B-AG-LB | |||
面板开孔图  | |||
| Panel cut out | |||
H6B系列外壳(单扣)Series housing (Single buckle)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 面板安装 带盖/Unsealed lower shell with cover | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | H6B-AD-LB |  | |
| 表面安装 高结构/Upper shell with high structure | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
 | PG13.5一个进线孔H6B-SGR-LB-PG13.5 | ||
| PG16 | H6B-SGR-LB-PG16 | ||
| M20 | H6B-SGR-LB-M20 | ||
| PG13.5两个进线孔H6B-SGR-LB-2PG13.5 | |||
| PG16 | H6B-SGR-LB-2PG16 | ||
| M20 | H6B-SGR-LB-2M20 | ||
| 金属防护盖/Metal protective cover | 连接方式 Connection method | 型号/Type | 尺寸图/Drawing |
 | H6B-MCV-2B/1 |  | |
 | H6B-MCV-2B/2 | ||
| 金属防护盖/Metal protective cover | 连接方式 Connection method | 型号/Type | 尺寸图/Drawing |
 | H6B-MCV-1L/SC.1S |
H6B系列外壳(单扣) Series housing (Single buckle)
防护等级Protection grade: IP65
防护等级Protection grade: IP65
| 表面安装 带盖/Cover the bottom shell With cover | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
| PG13.5一个进线孔 | H6B-SDR-LB-PG13.5 |   | |
 | PG16 | H6B-SDR-LB-PG16 | |
| M20 | H6B-SDR-LB-M20 | ||
| M25 | H6B-SDR-LB-M25 | ||
| PG13.5 两个进线孔 | H6B-SDR-LB-2PG13.5 | ||
| PG16 | H6B-SDR-LB-2PG16 | ||
| M20 | H6B-SDR-LB-2M20 | ||
| M25 电缆对接下壳/Cable butt bottom shell | H6B-SDR-LB-2M25 | ||
 | 螺纹/Thread | 型号/Type | 尺寸图/Drawing |
| PG13.5 | H6B-TBF-LB-PG13.5 | ||
| PG16 | H6B-TBF-LB-PG16 |   | |
| M20 | H6B-TBF-LB-M20 | ||
| 电缆对接下壳 高结构/Cable but lower shull high structure 螺纹/Thread | 型号/Type | 尺寸图/Drawing | |
 | PG21 | H6B-TBFH-LB-PG21 | |
| PG29 | H6B-TBFH-LB-PG29 | ||
| M25 | H6B-TBFH-LB-M25 |  | |
| M32 | H6B-TBFH-LB-M32 |
表面安装高结构 带盖/Back cover lower shell high structure with cover
