L&R Electric Group产品选择指南 - 电子画册在线预览、各类电子画册在线制作-云展网平台

Meter Box

Property

●Fiberglass SMC meter box is made by craft of moulding SMC unsaturated polyester resin, Fiberglass reinforced plastics.

●Its specialty has solved the problem of wooden meter box, steel meter box and plastic meter box, such as easy to aging, rust, poor insulation performance, poor cold resistance, poor fire resistance and short service life.

●SMC meter box has good quality of high strength,Lightweight,anti-corrosion,installation fastness,rain proof,preventing electric energy stealing,anti-rust, easy to operate and so on.

SMC meter box can be installed on the pole, hanged on the wall or in the wall. Besides all kinds of mechanical meter or electric meter as well as user's switch and leakage protector can be installed inside.

MCCB Enclosure

The MCCB Enclosure suitable for 1P / 3P / 4P MCCB

Standard	Comply with IEC 61439-3
Rated voltage	240/415V
Material	Flame retardant plastic or Cold steel
Color	Gray
Dimension	H400×W300×D170mm H500×W400×D195mm

The Dimension can Acceptable Customization

Moulded Circuit breaker (MCCB)

Dimension

Wiring Diagram

Moulded Circuit Breaker (MCCB)

Overview

LMB1moulded case circuit breaker with rated insulation voltage 800V, applied in the power system of AC50(60)Hz, rated voltage 690V and below, ratedcurrent 1250A and below as the transfer not frequently. The circuit breaker has the protection devices of over load, short circuit and under voltage ,it can protect the circuit and power equipment from broken.

The MCCB can be sorted to C type (basic),L type (standard), according to its rated limit short circuit breaking capacity.

The MCCB has the features small volume, breaking capacity high, electric arcing short ,anti-vibration. It is the ideal product for application in land and ship.

The installation can be vertical or level and the standard conforms to IEC60947-2 and GB14048.2

Protection Characteristic

Ui of release(A)	Thermal breaking release (	40for land,45° Cfor ship)	Electromagnetic releasebreaking current(A)	Remark
Ui of release(A)	1.05In(cool station)no breaking time(h)	1.30(thermal station)breaking time(h)	Electromagnetic releasebreaking current(A)	Remark
10<In<63	>=1	<1	10ln ± 20%	Power distribution
63<In<100	>=2	<2	10ln ± 20%
100<In<800	>=2	<2	5ln±20%&10ln±20%

Main Parameters

Type	LMB1-63	LMB1-125	LMB1-250	LMB1-400	LMB1-630	LMB1-800
Poles	3 & 4 pole					3 pole
Rated current	6,10,16,20,2532,40,50,63	63,80,100,125	125,160,180200,225,250	225,250,315350,400	400,500,630	630,800
Rated voltage Ue V	400V800VA
Rated insulation volt Ui V
Utilization category
Rated limited capacity luc(KA)	50	50	50	65	75	100

Mini Circuit Breaker (MCB)

Overview

LZC45-63 High breaking mini circuit breaker is mainly used for overload and short-circuit protection. It works in the circuit of 50/60Hz, AC 230/400V with rated current from 1A to 63A. The breaker can be used as a leakage breaker by assembling with leakage tripper. It confirms with IEC60898 standard.

Main technical data

Rated current In	1A-63A
Pole number	1P,2P,3P,4P
Rated voltage Ue	AC230/400V
Rated frequency	50/60Hz
Rated breaking capacity	3KA/4.5KA
Tripping characteristics	B,C,D
Mechanical life	10000 times
Electrical life	4000 times

Installation chart

Mini Circuit Breaker (MCB)

Overview

C65 mini circuit breaker belongs to the advanced level of the nineties in the international instead of the old generation of C45N. And they also have many merits of high protective grade (up to Ip20), highbreaking capacity, good reliability of sensitive action, convenient multi-pole assorting, long using life etc. They are mainly used for overload and short circuit protection within the circuit of AC 50Hz, 230V in single pole, 40oV in double, three & four poles of lighting distribution system in industry & commerce. Meanwhile, they are also used in turning on & off the electric apparatus and lighting circuit under the normalcondition.

Main technical data

Type	C65
Number of poles	1P, 2P, 3P, 4P
Rated Current(A)	1,2,3,4,6,10,16,20,25,32,40,50,63A
Breaking Capacity(A)	6000/10000
Rated Voltage(V)	230/400V
Rated Frequency(Hz)	50/60Hz
Endurance	≥4000
Circumstance Temp.(℃)	-5℃~+40℃
Electrical Life	≥6000
Mechanical Life	≥20000
Terminal protection	IP20

Dimension

Overcurrent Protection Characteristic

Test	Type	Current	Start state	Tripping/no tripping time	Exected result	Note
A	C	1.05 ln	Cold	t≥1h	Not-trip	The current rise toexpected valuewithin 5s
B	c	1.30 ln	Follow test A	t<1h	Not-trip
C	C	7ln	Cold	t≥0.1s	Trip
D	C	15 In	Cold	t<0.1s	Trip

MV Installation Diagram

Line Hardware

Application

●The connection fittings are used to connect and combine insulators, suspension clamps, tension clamps and protective fittings into suspension or tension strings (groups).

●The meaning of the letters in the product model: q-ball head hanging ring P-plane (parallel) contact w-bowl head s-double U-U L-joint plate, pull rod, diamond z-right angle y-extension b-plate t-adjustment.

●Classification and application: U-shaped hanging ring, double plate, right angle hanging plate, extension ring, U-shaped screw and other fittings are called general fittings, which are used for the connection between insulator strings and fittings, between clamps and insulator strings, and between ground wires and towers. Ball head hanging ring and bowl head hanging plate are special fittings for connecting ball and socket insulators

Standard

ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods

●ISO4948-1 Steels—Classification—Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition

●BS 3288 Insulator and conductor fittings for overhead power lines

Q/QP Ball Eye

Material:Hot Dipped galvanized Steel

Type	Dimension(mm)					Link Marker	Failure Load(KN)
Type	d	①	b	d1	h	Link Marker	Failure Load(KN)
Q-7	17	22	16	33.3	50	16	70
QP-7	17	22	16	33.3	50	16	70
QP-10	17	22	16	33.3	50	16	100
QP-12	17	24	16	33.3	50	16	120
QP-16	21	26	20	41	60	20	160

Line Hardware

QH Ball Eye

Material:Hot Dipped galvanized Steel

Type	Dimension(mm)					Link Marker	Failure Load(KN)
Type	b	d	d1	H	H1	Link Marker	Failure Load(KN)
QH-7	16	17	33.3	100	57	16	70
QH-10	18	17	33.3	110	57	16	100
QH-12	19	17	33.3	120	65	16	120
QH-16	18	21	41	127	45	20	160

Q-U Ball Eye

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)					Failure Load(KN)
Type	H	d	d1	M	C	Failure Load(KN)
Q-7U	80	17	33.3	16	18	70
Q-10U	80	17	33.3	18	20	100
Q-12U	95	17	33.3	22	22	120
Q-16U	80	21	41	24	22	160

Line Hardware

W Socket Eye

Material:Hot dip galvanized steel W type pin made of stainless steel

Type	Dimension(mm)					Link Marker	Failure Load(KN)
Type	b	C1	C2	H	①	Link Marker	Failure Load(KN)
W-7A	16	19.2	34.5	70	20	16	70
W-7B	16	19.2	34.5	115	20	16	70
W-10	18	19.2	34.5	85	20	16	100
W-12	20	19.2	34.5	90	24	16	120

WS Socket Eye

Material:Hot dip galvanized steel W type pin made of stainless steel R type pin made of stainless steel

Type	Dimension(mm)					Link Marker	Failure Load(KN)
Type	C	C1	C2	M	H	Link Marker	Failure Load(KN)
WS-7	20	19.2	34.5	16	70	16	70
WS-10	20	19.2	34.5	18	85	16	100
WS-12	24	19.2	34.5	22	85	16	120
WS-16	26	23.0	42.5	24	95	20	160

Line Hardware

WSY Socket Clevis

Material:Hot dip galvanized steel W type pin made of stainless steel

Type	Dimension(mm)				Link Marker	Failure Load(KN)
Type	C1	C2	M	R	Link Marker	Failure Load(KN)
WSY-21	42.2	23	27	100	20	210
WSY-30	51	27.5	30	110	24	300

Socket Thimble

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)						Failure Load(KN)
Type	L	L1	L2	L3	L4	H	Failure Load(KN)
DDT-07	75	55	35	37	23	97	70

Line Hardware

U Anchor Shackles

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)					Failure Load(KN)
Type	C	M	d	H	R	Failure Load(KN)
U-7	20	16	16	80	10	70
U-10	22	18	18	85	11	100
U-12	24	22	20	90	12	120
U-16	26	24	22	95	13	160

UL Anchor Shackles

Material:Hot dip galvanized steel W type pin made of stainless steel

Type	Dimension(mm)					Failure Load(KN)
Type	C	M	d	H	R	Failure Load(KN)
UL-7	20	16	16	120	10	70
UL-10	22	18	18	140	11	100
UL-12	24	22	20	140	12	120
UL-16	26	24	22	140	13	160

Line Hardware

U-Bolts

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)				Failure Load(KN)
Type	C	M	H1	H2	Failure Load(KN)
U-1880	80	18	110	75	35
U-2080	80	20	120	80	47
U-2280	80	22	130	90	57

Z Link Plate

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)				Failure Load(KN)
Type	C1	C2	M	H	Failure Load(KN)
Z-7	18	18	16	80	70
Z-10	20	20	18	80	100
Z-12	20	24	22	100	120
Z-16	26	26	24	100	160

Line Hardware

PS Clevise

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)					Failure Load(KN)
Type	C	b	M	H	①	Failure Load(KN)
PS-7	18	16	16	90	20	70
PS-10	18	18	18	100	22	100
PS-12	24	20	22	95	24	120
PS-16	26	24	24	155	26	160

PD Link Clevis

Material:Hot dip galvanized steel

Type	Dimension(mm)					Failure Load(KN)
Type	φ	H	b	L	R	Failure Load(KN)
PD-7(PD-0770)	18	70	16	40	26	70
PD-10(PD-1080)	20	80	16	36	26	100
PD-12(PD-12100)	24	100	16	50	24	120
PD-16	26	100	18	60	35	160

Line Hardware

P Extension Link Clevis

Material:Hot dip galvanized steel R type pin made of stainless steel

Type	Dimension(mm)				Failure Load(KN)
Type	b	C	M	H	Failure Load(KN)
P-7	6	18	16	70	70
P-10	8	20	18	80	100
P-12	10	24	22	90	120
P-16	12	26	24	100	160

D Shackles

Material:Hot dip galvanized steel R type pin made of stainless steel

Dimension(mm)							Failure Load(KN)
A	C	D	E	F	R	S	Failure Load(KN)
70	19	35	18	9.5	16	16	70
76	21	54	22	13	19	19	120

Line Hardware

Ball-ended Hook and pig tail hook

Material:Hot Dipped galvanized Steel

Tension Clamp

Tension clamp refers to the hardware used to fix the conductor to bear the tension of the conductor and hang the conductor to the tension string or tower

NLL/NLD Strain Clamps

Material:

Body: NLL are made of aluminum NLD are made of hot dip galvanized steel U bolt/ bolt: Hot dip galvanized steel R Pin: Stainless Steel

Type	U bolt		Applicable conductordiameter(mm²)
Type	Qty	Diameter	Applicable conductordiameter(mm²)
NLL-1	2	M12	5.0-15.5
NLL-2	2	M12	8.2-17.0
NLL-3	3	M14	11.4-20.0
NLL-4	4	M16	13.6-25.0
NLD-1	2	M12	5.0-10.0
NLD-2	3	M12	10.0-14.0
NLD-3	4	M16	14.0-18.0
NLD-4	4	M16	18.1-23.0

NLD

NY Hydraulic Compression Type Strain Clamps

Type	Applicable conductordiameter(mm²)
NY-95/15	LGJ-95/15
NY-95/20	LGJ-95/20
NY-120/20	LGJ-120/20
NY-120/25	LGJ-120/25
NY-150/20	LGJ-150/20
NY-150/25	LGJ-150/25
NY-150/35	LGJ-150/35
NY-185/25	LGJ-185/25
NY-185/30	LGJ-185/30
NY-185/45	LGJ-185/45

Type	Applicable conductordiameter(mm)	Failure Load ( KN)
CGU-2	7.0-12.4	40
CGU-3	12.4-17.0	40
CGU-4	19.0-21.5	40
CGU-5	24.2-33.0	70

Type	Applicable conductordiameter(mm)	Failure Load(KN)
XGU-1	5.0-7.0	40
XGU-2	7.1-13.0	40
XGU-3	13.1-21.0	40
XGU-4	21.1-26.0	40

Suspension Clamp

The suspension clamp is mainly used for overhead power lines or substations, and the conductor and lightning wire are hungon the insulator string or the lightning wire is hung on the tower through the connecting hardware; It is made of Horse Iron and aluminum alloy.

CGU/XGU Suspension Clamps

Material:

Body & Keeper: CGU are made of aluminum. XGU are made of hot dip galvanized steel. U bolt/ bolt: Hot dip galvanized steel R Pin: Stainless Steel

Preformed dead end clamp

Preformed Guy Grip

Material:Hot-dip galvanized steel wire

Type	Applicableconductor (mm²)	Length(mm)	Rod diameter(mm)	No.of rods
LRNL-50/LJ	AAAC/AAC 50	685	3.00	3
LRNL-100/LJ	AAAC/AAC 100	800	3.50	3
LRNL-150/LJ	AAAC/AAC 150	889	4.00	4
LRNL-200/LJ	AAAC/AAC 200	1016	4.00	5
LRNL-50/8	ACSR 50/8	685	3.00	3
LRNL-100/8~20	ACSR 100/8~20	876	3.50	4
LRNL-150/8~35	ACSR 150/8~35	1016	4.00	5
LRNL-200/12~50	ACSR 200/12~50	1155	4.80	5

PG Clamp And Connector

APG PG Clamp

Material:The main body is made of aluminum, and the bolt is hot-dip galvanized steel

Type	Bolts		Applicable conductor diameter(mm²)
Type	Qty	Diameter	Applicable conductor diameter(mm²)
APG-A1	1	M8	16-70
APG-A2	1	M8	16-150
APG-B1	2	M6	16-35
APG-B2	2	M8	16-70
APG-B3	2	M8	16-150
APG-C1	3	M8	16-70
APG-C2	3	M8	16-150
APG-C3	3	M10	25-240

CAPG PG Clamp

Material:The body is made of aluminum and copper, and the bolt are hot-dip galvanized steel

Type	Bolts		Applicable conductor diameter(mm²)
Type	Qty	Diameter	AL	CU
CAPG-A1	1	M8	16-70	6-50
CAPG-A2	1	M8	25-150	10-95
CAPG-B1	2	M8	16-70	6-50
CAPG-B2	2	M8	25-150	10-95
CAPG-B3	2	M10	25-240	25-200
CAPG-B4	2	M10	35-300	35-240
CAPG-C2	3	M8	25-150	10-95
CAPG-C3	3	M10	25-240	25-200

PG Clamp And Connector

JB PG Clamp(Aluminum wire,ACSR)

Material:The main body is made of aluminum, and the bolt is hot-dip galvanized steel

Type	Bolts		Applicable conductordiameter(mm²)
Type	Qty	Diameter	Applicable conductordiameter(mm²)
JB-0	2	M10	16-25
JB-1	2	M12	35-50
JB-2	3	M12	70-95
JB-3	3	M16	120-150
JB-4	3	M16	185-200

JBT PG Clamp

Material:The main body is made of copper, and the bolt is hot-dip galvanized steel

Type	Bolts		Applicable conductordiameter(mm²)
Type	Qty	Diameter	Applicable conductordiameter(mm²)
JBT-10~70	2	M8	10-70
JBT-10~70	3	M8	10-70
JBT-16~120	2	M10	16-120
JBT-16~120	3	M10	16-120
JBT-50~240	2	M10	50-240
JBT-50~240	3	M10	50-240
JBT-00	2	M10	16-25/16-25
JBT-10	2	M10	35-50/16-25
JBT-11	2	M10	35-50/35-50
JBT-21	2	M12	70-95/35-50
JBT-22	2	M12	70-95/70-95
JBT-31	3	M12	120-150/35-50

JBTL PG Clamp

Material:The body is made of aluminum and copper, and the bolt is hot-dip galvanized steel

Type	Bolts		Applicable conductordiameter(mm²)
Type	Qty	Diameter	Applicable conductordiameter(mm²)
JBTL-10~70	2	M8	10-70
JBTL-10~70	3	M8	10-70
JBTL-16~120	2	M10	16-120
JBTL-16~120	3	M10	16-120
JBTL-50~240	2	M10	50-240
JBTL-50~240	3	M10	50-240

PG Clamp And Connector

Aluminium PG Clamp

Material:The main body is made of aluminum, and the bolt is hot-dip galvanized steel or Stainless steel

Type	Dimension(mm)
Type	L	W	H	M	No. of bolt
25-70mm²	75	40	20	10	2
70-150mm2	98	54	34	10	3
Up-to 300mm²	160	60	32	14	4

Aluminium Line Tap Connector

Material:Aluminium

Type	Dimension(mm)
Type	M	L	W	H	1
50mm²	8	32	22	42	10
100mm²	12	48	29	58	15

DL Aluminium Lug

Material:Aluminium

Type	①	D	d	L	W	S
DL-10	8.5	10	5.5	65	16	2.8
DL-16	8.5	11.8	7.6	70	16	3
DL-25	8.5	12	8	76	18	3.1
DL-35	10.5	14	8.5	84	20.6	3.1
DL-50	10.5	15.6	9.8	90	23.2	4.4
DL-70	12.5	17.8	12	104	25.6	4.4
DL-95	12.5	20.2	13.8	108	27.6	4.9
DL-120	14.5	21.6	15.2	118	30.2	5.4
DL-150	14.5	24.4	16.8	125	34.4	5.8
DL-185	16.5	27	19	129	37.4	5.8
DL-240	16.5	30	20.8	138	40.4	7

DT Copper Lug

Material:Copper

Type	φ	D	d	L	W	S
DT-10	8.5	9	5.2	63	16	2.2
DT-16	8.5	10	6.2	66.2	16	2.2
DT-25	8.5	11.2	7	72	18	2.6
DT-35	10.5	12.2	8.2	75.8	20	2.6
DT-50	10.5	14	9.8	86.2	23	3.4
DT-70	12.5	16.2	11.4	93	26	4
DT-95	12.5	18	13.8	103	28	4
DT-120	14.5	20	14.8	110.4	30	4.6
DT-150	14.5	22	17.2	117.2	34	5.2
DT-185	16.5	24	19	124	37	5.8
DT-240	16.5	27	20.8	135	40	6.4

Lug

DTL Bimetal Lug

Material:Copper,Aluminium

Type	①	D	d	L	W	S
DTL-1-16	8.5	10	5.5	70	16	3.0
DTL-1-25	8.5	12	7.0	75	18	3.5
DTL-1-35	10.5	14	8.5	85	20	3.5
DTL-1-50	10.5	16	9.5	90	23	4.0
DTL-1-70	12.5	18	12.0	102	26	4.5
DTL-1-95	12.5	21	13.0	112	28	5.0
DTL-1-120	14.5	23	15.0	120	30	5.5
DTL-1-150	14.5	25	16.0	126	34	6.0
DTL-1-185	16.5	27	18.0	133	37	6.5
DTL-1-240	16.5	30	20.0	140	40	7.5

DTL Bimetal Lug

Material:Copper,Aluminium

Type	①	D	d	L	W	S
DTL-2-16	10.5	16	6	80	20	3
DTL-2-25	10.5	16	7	80	20	3
DTL-2-35	10.5	16	8.5	80	20	3
DTL-2-50	13	20	10	90	24	4
DTL-2-70	13	20	11.5	90	24	4
DTL-2-95	13	20	13.5	90	24	4
DTL-2-120	13	25	15	115	30	4.5
DTL-2-150	13	25	16.5	115	30	4.5
DTL-2-185	13	32	18.5	122	35	6
DTL-2-240	13	32	21	122	35	6

SC Tinned Copper Lug

Material:Tinned Copper

Type	φ	D	d	L	W	S
SC-10	8.5	8	5.8	39	11.5	2.2
SC-16	10.5	9	6.5	42	14.5	2
SC-25	8.5	10	7.6	47	14.5	2.4
SC-35	10.5	11	8.5	52	15.5	2.5
SC-50	10.5	13	10	54	19	3
SC-70	12.5	16	12	62	23	4
SC-95	12.5	18	14	64	26	4
SC-120	12.5	19	15	72	27.5	4
SC-185	16.5	24	18.8	86	34.5	5
SC-240	16.5	26	21	91	37.5	5

Bolt type torque Lug

Type	Section area(mm²)	Dimension(mm)				LB(mm)	Bolt No.	AF(mm)
Type	Section area(mm²)	L1	L2	D1	D2	LB(mm)	Bolt No.	AF(mm)
BLMT-6/50-13	6-50	50	20	18	10	13	1	13
BLMT-25/95-13	25-95	60	30	24	12.8	13	1	13
BLMT-25/95-17	25-95	60	30	24	12.8	17	1	13
BLMT-35/150-13	35-150	86	36	28	15.8	13	1	17
BLMT-35/150-17	35-150	86	36	28	15.8	17	1	17
BLMT-95/240-13	95-240	112	60	33	20	13	2	19
BLMT-95/240-17	95-240	112	60	33	20	17	2	19
BLMT-95/240-21	95-240	112	60	33	20	21	2	19
BLMT-120/300-13	120-300	120	65	37	24	13	2	22
BLMT-120/300-17	120-300	120	65	37	24	17	2	22
BLMT-185/400-13	185-400	137	80	42	25.5	13	3	22
BLMT-185/400-17	185-400	137	80	42	25.5	17	3	22
BLMT-185/400-21	185-400	137	80	42	25.5	21	3	22
BLMT-500/630-13	500-630	150	95	50	33	13	3	27

Joint And Connector

JY Cable Joint

Material:Aluminium

Type	Cable range Applicable	Dimension(mm)						Rated Failure Load(KN)
Type	Cable range Applicable	L	D	d	L1	D1	d1	Rated Failure Load(KN)
JY-70/10	JKLGYJ-70/10	360	25	13	110	12	4.5	21
JY-95/15	JKLGYJ-95/15	430	26	15	130	14	5.7	31.5
JY-120/20	JKLGYJ-120/20	430	30	16	130	14	6.2	36.9
JY-150/25	JKLGYJ-150/25	500	30	18.5	150	14	7.0	48.7
JY-185/25	JKLGYJ-185/25	520	32	20.5	150	14	7.0	53.5
JY-240/30	JKLGYJ-240/30	570	36	23	170	16	7.9	68

JBE Repair Sleeves For ACSR Conductor

Material:Aluminium

Type	Cable range Applicable
		Dimension(mm)
		D	L	R
JBE-35/6	LGJ-35/6	16	120	4.8
JBE-50/8	LGJ-50/8	18	130	5.5
JBE-70/10	LGJ-70/10	22	130	6.5
JBE-95/15~20	LGJ-95/15/20	24	140	8.0
JBE-120/7	LGJ-120/7	26	140	8.0
JBE-120/20~25	LGJ-120/20/25	26	140	8.6
JBE-150/8~20	LGJ-150/8/20	30	140	9.1
JBE-150/25~35	LGJ-150/25/35	30	170	9.5
JBE-185/10~30	LGJ-185/10/30	32	170	10.3
JBE-185/45	LGJ-185/45	34	170	10.8

Joint And Connector

GL-G Aluminium Connecting Pipe(Passing Though)

Material:Aluminium

Type	L	D	d
GL-G-16	65	10	5.5
GL-G-25	70	12	7
GL-G-35	75	14	8.5
GL-G-50	80	16	10
GL-G-70	90	18	11.5
GL-G-95	95	21	13.5
GL-G-120	100	23	15
GL-G-150	105	25	16.5
GL-G-185	110	27	18.5
GL-G-240	120	30	21

GT-G Copper Connecting Pipe(Passing Though)

Material:Copper

Type	L	D	d
GT-G-16	56	9	6
GT-G-25	60	10	7
GT-G-35	64	11	8.5
GT-G-50	72	13	10
GT-G-70	78	15	11
GT-G-95	85	18	13
GT-G-120	90	20	15
GT-G-150	94	23	17
GT-G-185	100	25	19
GT-G-240	110	27	21

Copper-Aluminium connecting tubes

Material:Copper,Aluminium

Type	D	d	D1	d1	L	L1	L2
GTL-10	9	4.5	9	4.2	70	28	28
GTL-16	9	5.5	9	5.0	75	31	28
GTL-25	12	7.0	10	5.5	80	32	30
GTL-35	14	8.5	11	7.0	90	37	32
GTL-50	16	9.5	13	8.5	95	42	34
GTL-70	18	12.0	15	9.6	100	46	35
GTL-95	21	13.0	17	12.0	110	50	41
GTL-120	23	15.0	19	13.0	112	52	43
GTL-150	25	16.0	21	15.0	118	55	46

LV ABC Aerial Electrical Fittings

Insulation piercing connector(IPC)

General

●Piercing connector, simple installation, need not strip the cable coat.

Moment nut, piercing pressure is constant, keep good electric connection and make no damage to lead.

●Self-seam frame, wetproof, waterproof, and anti-corrosion, extend the using life of insulated lead and connector

●Adopted special connecting tablet, apply to joint of Cu(Al) and Cu(Al) or Cu and Al

Small electric connecting resistance, connecting resistance less than 1.1 times of the resistance of branch conductor with the same length.

Special insulated case body, resistance to illumination and environmental aging, the insulation strength can up to 12KV.

Arc surface design, apply to connection with the same(different) diameter, wide connection scope(0.75mm2-400mm2).

Simple installation

1.Adjust the connector nut to suitable location.

2.Put the branch wire into the cap sheath fully.

3.Insert the main wire.if there are two lays of insulated in the main cable,should strip a certain length of the pirst insulated lay from inserted end.

4.Turn the nut by hand,and fix the connector in suitable location.

5.Screw the nut with the sleeve spanner

6.Screw the nut continually until the top part is cracked and dropped down

How to choosing Insulation piercing connector

●Simple installation

Con be branch of cable without striping the insulated coat and the joint is completely insulated. Make branch in the random location of cable without cutting off the main cable. Simple and reliable installati just need sleeve spanner, can be installed with on live line

The joint has good resistance to distortion, quake, fire, wet, electrochemical corrosion and aging, need no maintenance. Has been used successfully for 30years

●Economical cost

Small installation space, save the cost of bridge and land construction. In structural application, there need no terminal box, junction box and return wire of cable, save cable cost. The cost of cables and clamps is lower than other power supply system

LV ABC Aerial Electrical Fittings

Product type and application scope

LRPE

LR2-95

LR3-95

Type	Material of teeth	Main line(mm²)	Branch line(mm²)	Nominal current(A)	Piercing depth
LR756	Al/Cu/Bimetallic	0.75~6	0.75~6	41	1-1.5
LR041	Al/Cu/Bimetallic	1.5~35	1.5~10	41	1.5-2
LR101	Al/Cu/Bimetallic	1.5~2.5	1.5~10	55	1.5-2
LREP	Al/Cu/Bimetallic	16~95	1.5~10	55	1-2
LR2-95	Al/Cu/Bimetallic	16~95	4~54.6	160	1.5-2
LR2-150	Al/Cu/Bimetallic	50~150	6~54.6	162	1.5-2.5
LR3-95	Al/Cu/Bimetallic	16~95	16~95	198	1.5-2
LR4-150	Al/Cu/Bimetallic	50~150	50~150	219	1.5-2.5
LR6	Al/Cu/Bimetallic	120~240	25~120	360	1.5-2.5
LR7	Al/Cu/Bimetallic	150~240	10~25	336	1.5-2.5
LR240	Al/Cu/Bimetallic	95~240	95~240	1040	1.5-2.5
LR300	Al/Cu/Bimetallic	300	ANY	1040	1.5-2.5
LR400	Al/Cu/Bimetallic	400	ANY	1040	1.5-2.5

JBC-1

JBC-2

JBC50-240

Type	Material of teeth	Main line(mm²)	Branch line(mm²)	No. Bolt
JBC-1	Al/Cu/Bimetallic	35~70	6~35	1
JBC-2	Al/Cu/Bimetallic	35~150	35~150	1
JBC50-240	Al/Cu/Bimetallic	50~240	50~240	2

LV ABC Aerial Electrical Fittings

Product type and application scope

TT2D82F

IPC3.1

IPC3.2

IPC3.3

IPC3.4

TTD121F

TTD151F

TTD201F

TTD281F

TTD451F

Type	Conductor Range (mm²)		No. Bolt
Type	Main	Tap	No. Bolt
IPC3.1	16-95	10-25	1
IPC3.2	70-95	70-95	1
IPC3.3	120-185	16-25	1
IPC3.4	70-185	70-185	2
TTD121F	25-95	2.5-25	1
TTD151F	25-95	(2.5)6-35	1
TTD201F	35-95	25-95	1
TTD281F	50-185	6-35	1
TTD282F	25-95	25-35	1
TTD451F	95-240	95-240	2

LV ABC Aerial Electrical Fittings

Product type and application scope

CT-1

CT-2

CT-3

Type
	Conductor Range (mm²)
	Main	Tap
CT-1	6-95	1.5-6
CT-2	6-150	2.5-25
CT-3	6-150	4-35
CT-4	25-150	25-95
CT-5	25-150	16-95

End Cap

Type	Conductor cross-section(mm²)
PC6-35	6-35
PC35-70	35-70
PC70-95	70-95
PC95-120	95-120

LV ABC Aerial Electrical Fittings

MJPT Pre-insulated sleeve

Product property

MJPT is designed to connect the insulated cable (include ABC cable) in aerial distribution network. It is in accordance with NFC33-021. The sleeve is with some tension.

And its cap can prevent the water into the barrel. It is colored differently to distinguish the cable sizes.Marked with type, cable size, die size, inner cable length and number of crimping.

Material:Aluminium

Type	Cable size (mm²)		Plastic sleeve diameter(mm)	Length(mm)
Type	A	B	C	L
MJPT 16/16	16	16	20	98.5
MJPT 25/25	25	25	20	98.5
MJPT 35/35	35	35	20	98.5
MJPT 50/50	50	50	20	98.5
MJPT 70/70	70	70	20	98.5
MJPT 95/95	95	95	20	98.5

MJPB Pre-insulated sleeve

Product property

MJPB is designed to connect the insulated cable (include ABC cable). It is in accordance with NFC33-021. The sleeve is without tension.

And its cap can prevent the water into the barrel. It is colored differently to distinguish the cable size.Marked with type, cable size, die size, inner cable length and number of crimping.

Material: Al-99.5%

Type	Cable size (mm²)		Plastic sleeve diameter(mm)	Length(mm)
Type	A	B	C	L
MJPB 6/16	6	16	20	98.5
MJPB 10/16	10	16	20	98.5
MJPB 16/16	16	16	20	98.5
MJPB 16/25	16	25	20	98.5
MJPB 25/25	25	25	20	98.5

LV ABC Aerial Electrical Fittings

MJPN Pre-insulated sleeve

Product property

MJPTN is designed to connect the neutral messenger in aerial bundled cable. It is in accordance with NFC33-021. The sleeve is with full tension.

And its cap can prevent the water into the barrel. It is colored differently to distinguish the cable size.Marked with type, cable size, die size, inner cable length and number of crimping.

Material: Aluminium alloy

Type	Cable size (mm²)		Plastic sleeve diameter(mm)	Length(mm)
Type	A	B	C	L
MJPTN 54.6/54.6	54.6	54.6	20	172.5
MJPTN 54.6/70	54.6	70	20	172.5
MJPTN 70/70	70	70	20	172.5
MJPTN 95/95D	95	95	20	172.5

CPTAU Pre-insulated bimetal lug

Product property

CPTAU is designed to connect the insulated cable (include ABC cable). It is in accordance with NFC33-021.

The waterproof cap can prevent the water into the barrel. It is colored differently to distinguish the cable size.Marked with type, cable size, die size, inner cable length and number of crimping.

Material: E-Cu; Al-99.6%

Type	Dimension (mm)			Length(mm)
Type	C	B	①	L
CPTAU16-10	16	20	10.5	73
CPTAU25-12	20	24	13	98.5
CPTAU35-12	20	24	13	98.5
CPTAU50-12	20	24	13	98.5
CPTAU54.6-12	20	24	13	98.5
CPTAU70-12	20	24	13	98.5
CPTAU95-12	20	24	13	98.5

LV ABC Aerial Electrical Fittings

Anchoring Bracket

Product property

Anchoring ABC cables with neutral messenger on poles(wood, concrete etc), Excellent in industrial and saline environment. Fixed by 2×(14mm or 16mm) bolts or two stainless straps 0.75X20mm. It is in accordance with NFC 33-040.

Material:High strength aluminium alloy by casting

LR81

LR82

LR83

The universal hook LR96,LR97and LR98 is usedwith bands in pole installations and with screws in wall installations. The hook is delivered without screws.

Anchoring clamp

Product property

They are characterized by high mechanical stability, reduced dimensions for easier handing,high mechanical and climatic resistance. Cable gripping device in insulating material ensures the double insulation of the neutral core and avoids damage to sheath, secured parts, no tools required. Stainless steel bail with two marbles compressed on the end, the conception allows an easier locking on the body of the clamp. They are in accordance with NFC 33-041.

Material: High strength aluminium alloy, nylon plus fiber glass, stainless steel.

Type	Cross-section(mm²)
PAM-06	16-20
PAM-07	16-25
PAM-08	16-25
PAL1400	35-70
PAL1500	35-70
PAL2000	70-120
JBG-1	50-70

LV ABC Aerial Electrical Fittings

Anchoring clamp

SDMR

SDO

SDTR

SDE

SK-1

SK-2

2.1

LV ABC Aerial Electrical Fittings

Anchoring clamp

Product property

The plastic anchoring clamp is suitable for insulated low-voltage ABC cable. It is also suitable for multiple conductors. Easy installation and perfect insulated function. It is in accordance with NFC 33-042.

LA2

DCR-1

PA1500

PA2000
Material: Nylon plus fibre glass

Type	Cross-section(mm²)
STA	2×(16-35)
STB	2×(16-25)
STC	4×(16-25)
STD	1×(16-70)
LA1	4×(16-25)
LA2	2×(6-16)
DCR-1	1×(4-25)
DCR-2	1×(4-25)
2.1	1×(16-25)
PA1500	1×(50-70)
PA2000	1×(70-120)

LV ABC Aerial Electrical Fittings

Anchoring clamp

LV ABC Aerial Electrical Fittings

Anchoring clamp

Product property

It is used to terminate 4-core of aerial bundle conductor. Its function is fixing and tightening the insulation conductor.

Material: Mild steel, nylon plus fiber glass

Type	Cross-section(mm²)
NES-B0	4X(25-125)
NES-B1	4X(25-35)
NES-B2	4X(35-50)
NES-B3	4X(50-70)
NES-B4	4X(70-95)

LV ABC Aerial Electrical Fittings

NEJ Wedge strain clamps for insulation cable

Application

This series are mainly used in 20kV or less than 10kV distribution system to fix and tighten the aluminum insulating wires at the corner or the end of the insulators on the stilt.

Technical Data

Type	Applicable conductor (mm²)			Inner clamping range	Grip strength (kN)	Failure load (kN)
Type	1kv	10kv	20kv	Inner clamping range	Grip strength (kN)	Failure load (kN)
NEJ-1	35	-	-	Φ10-Φ11	3.4	12.4
	50	16	-	Φ12-Φ13	4.6
	70	25	-	Φ14-Φ15	6.7
	95	35	-	Φ15-Φ17	8.9
NEJ-2	120	50-70	25-35	Φ16-Φ18.5	11.3	20.8
NEJ-2	150	95	50	Φ19-Φ21	13.7	20.8
NEJ-3	185	120	70	Φ21-Φ23	17.3	32.0
NEJ-4	240	150	95	Φ23-Φ25.6	22.5	41.7
	-	185	120	Φ24-Φ26	22.5
	-	240	150	Φ26-Φ27.5	22.5
	-	-	185-240	Φ27.5-Φ31.5	22.5
NEJ-5	-	300	一	Φ27.5-Φ31.5	28.2	52.1

LV ABC Aerial Electrical Fittings

JNS Four(two)-core bunched cable strain clamp series

Application

JNS series four-core bunched cable strain clamp series are fully used for fixing or tightening 1kV and less than 1kV overhead four(two)-cores bunched cable at ends of circuit

Function and Features

●It adopts four(two)-core parallel groove parallel gap structure, Put the four insulation cables into clamp according to circuit design without peeling off the coat, then tighten the bolt to bunch it.

●For inner block and filling pole with high strength, anti-climate resistance insulation plastic, it can be used for a long term;

Adopting wedge type self-tighten structure, after tightening the ring, it will be fixing, and get a quite big grasp strength.

JNS two-core bunched cable train clamp series

JNS four-core bunched cable train clamp series

Technical Data

Type	Applicablevoltage (kV)	Applicableconductor(mm²)	Dimension (mm)			Note
Type	Applicablevoltage (kV)	Applicableconductor(mm²)	A	B	C	Note
JNS-1A-1	1KV	4×10-4×16	200	78	45	Four cores
JNS-1A-2		4×16-4×50	260	100	62
JNS-2A		4×50-4×120	330	105	72
JNS-1C		2×10-2×16	200	78	30	Two cores
JNS-2C		2×16-2×50	260	100	40	Two cores

LV ABC Aerial Electrical Fittings

Suspension clamp

Product property

On poles, in alignment or angle, different level, also provide for hanging a public light bundle.

LR94

LR95

1.1A

1.1B

SHC-1

SHC-2

SHC-3

SHC-5

SHC-6

LV ABC Aerial Electrical Fittings

Suspension clamp

Type		Condcutor range(mm²)
	LR94	16-95
	LR95	16-95
	1.1A	16-95
	1.1B	16-95
	1.1C	2×(25-35) 4×(16-120)
	1.1D	16-95
ES54-14		16-95
PS1500		16-95
SHC-1		4×(10-25)
	SHC-2	2×(25-35)
SHC-3		4×(25-35)
SHC-4		4×(35-50)
SHC-5		4×(50-95)

SDPS25

LV ABC Aerial Electrical Fittings

Fixing Nail

LRZD-1

LRZD-2

LRZD-3

LRZD-4

Type	Condcutor range(mm²)
LRZD-1	15-47
LRZD-2	12-47
LRZD-3	15-47
LRZD-4	15-30

Portable Dispensers

LV ABC Aerial Electrical Fittings

Type 304 Stainless Steel Band

Function and Features

●Band and buckle can be quickly formed to suit virtually any diameter.

●Applications include hose clamps, pipes, signs, cables, especially where superior strength is required.

●Dispensers-Handy plastic dispensers available with certre tum facility and pocket for buckles.

●Excellent corrosion resistance.

Type 304 Stainless Steel

Type	Width		Thickness		Weight
Type	Inch	mm	Inch	mm	Lbs	kg
LRB1450	1/4	6.35	0.02	0.5	1.76	0.8
LRB3850	3/8	9.53	0.02	0.5	2.64	1.2
LRB1276	1/2	12.70	0.03	0.76	5.5	2.5
LRB5876	5/8	15.88	0.03	0.76	7.04	3.2
LRB3476	3/4	19.05	0.03	0.76	8.27	3.76

Available in mill coil lengths. All size in standard cardboard

Type 304 Stainless Steel

Type	Width		Thickness		Weight
Type	Inch	mm	Inch	mm	Lbs	kg
LRBD3850	3/8	9.53	0.02	0.5	3.08	1.4
LRBD1276	1/2	12.70	0.03	0.76	5.94	2.7
LRBD5876	5/8	15.88	0.03	0.76	7.48	3.4
LRBD3476	3/4	19.05	0.03	0.76	8.71	3.96

Customers can assign different colors for different sizes

LV ABC Aerial Electrical Fittings

Type 304 Stainless Steel Band

Stainless Steel Buckle

Tooth type

Type	For band width		Thickness
Type	Inch	mm	mm
LRBT14	1/4	6.35	0.8
LRBT38	3/8	9.53	1.0
LRBT12	1/2	12.70	1.2
LRBT58	5/8	15.88	1.2
LRBT34	3/4	19.05	1.5
LRBT1	1	25.4	1.8
LRBT114	1 1/4	32.5	2.0
LRBL14	1/4	6.35	0.6
LRBL38	3/8	9.53	0.7
LRBL12	1/2	12.70	0.7
LRBL58	5/8	15.88	0.8
LRBL34	3/4	19.05	1.0

Tooth type

Type	For band width		Thickness
Type	Inch	mm	mm
LRBL14	1/4	6.35	0.6
LRBL38	3/8	9.53	0.7
LRBL12	1/2	12.70	0.7
LRBL58	5/8	15.88	0.8
LRBL34	3/4	19.05	1.0

Screw type

Type	For band width		Thickness
Type	Inch	mm	mm
LRBL14	1/4	6.35	0.6
LRBL38	3/8	9.53	0.7
LRBL12	1/2	12.70	0.7
LRBL58	5/8	15.88	0.8
LRBL34	3/4	19.05	1.0

LV ABC Aerial Electrical Fittings

Application Tools

LRBT001 Band Clamp Tool

LRBT002Batchet Tension Tool

LRBT003 Heayy Duty Tool

LRBT004Ratchet Tensioner

LRBT005Bantam Tool

Type	Description	Weight
LRBT001	Band clamp tool for use with bands up to 3/4"(19.05mm) wide	2.0kg
LRBT002	Ratchet tension tool for use with bands up to 3/4"(19.05mm) wide, and also for all coated bands.	1.8kg
LRBT003	Heavy duty tool	2.3kg
LRBT004	Another type for ratchet tensioner for sue with bands up to 3/4"(19.05mm) wide and also for all coated bands.	1.8kg
LRBT005	It can be used with one hand. For using with bands up to3/4"(19.05mm) wide.	1.5kg

LV ABC Aerial Electrical Fittings

Ftth optical cable clamp

Anchor clamp class

YJ-002

Made of stainless steel 201/304

YJ-005

LV ABC Aerial Electrical Fittings

Ftth optical cable clamp

Anchor clamp class

Made of stainless steel 201/304

Installation mode

LV ABC Aerial Electrical Fittings

Ftth optical cable clamp

Anchor clamp class

Made of stainless steel 201/304

Installation mode

Hex Bolts

Application

The Hex bolts, concrete cavity depth and no higher cleanliness requirements, easy to install and inexpensive. Jacking by selecting the appropriate thickness of the buried depth, with the increase of buried depth, tension increased after the products are reliable and expandable functionality. Body material: stainless steel, carbon steel and other metal materials. Also known as through bolts, expansion bolts and expansion anchors, which is designed for consistent performance in concrete.

Widely used in securing the through objects'fastening, such as equipment,channel steel, guide rail, holder, steel structure, escalator, handrail and curtain wall etc. Every wedge anchor can be suitable for the standard anchorage depth, and also fit for shallow mining depth, to provide supreme flexibility for installation. Moreover the long thread offering the spacing installaiton, and can be flexibly adjustable to easy the installation.

ASTM A307and Hot Dip Galvanized ASTM153. Bolts are Coarse Threaded to a class 2 Fit. Hex Nuts and washers used on these bolts should be ordered separately.

Dia	Length(mm)
M12	50
M16	35
M16	100
M16	120
M16	300
M20	50
M20	100
M20	250
M20	300
M20	350

Support custom size

"A"Cable Suspension Bolts

Application

"A" cable suspension bolts are supplied with two square nuts. One nut is used to fasten the square head bolt to the pole and the other nut is used to secure a straight or angle cable suspension clamp to the bolt.

Material

Steel hot dip galvanized

5/8” Diameter - Minimum Tensile Strength 13,550

Catalognumber	BoltLength (in)	ThreadLength (in)	Weight/100 (lbs)
LR6645.A01	8	4	85
LR6645.A02	10	6	104
LR6645.A03	12	6	120
LR6645.A04	14	6	138
LR6645.A05	16	6	153
LR6645.A06	18	6	168
LR6645.A07	20	6	183
LR6645.A08	22	6	198
LR6645.A09	24	6	214

Brace bolts

Application

Brace bolts are used in place of carriage bolts or machine bolts to fasten braces to crossarms. The integral washer/hex head construction provides a static-proof design.

Material

Steel hot dip galvanized

Minimum Tensile Strength 4,250 Ibs

Catalognumber	Size(in)	ThreadLength (in)	Weight/100 (lbs)
LR8624-1/2	3/8 × 4 1/2	2	21

3/4” Diameter - Minimum Tensile Strength 20,050

Catalognumber	BoltLength (in)	ThreadLength (in)	Weight/100 (lbs)
LR6645.A10	10	6	165
LR6645.A11	12	6	187
LR6645.A12	14	6	204
LR6645.A13	16	6	220
LR6645.A14	18	6	220

Carriage Bolts

Application

MPS carriage bolts are roll threaded with square shoulder and square nut.

Material

Steel hot dip galvanized

3/8” Diameter - Minimum Tensile Strength 4,250 Ibs

Catalognumber	BoltLength (in)	ThreadLength (in)	Weight/100 (lbs)
LR8634	4	3	16
LR8634-1/2	4 1/2	3	16
LR8635	5	3	18
LR8636	6	3	22
LR8637	7	4	24
LR8638	8	4	26
LR8640	10	4	34

1/2” Diameter -Minimum Tensile Strength 8,500 Ibs

Catalognumber	BoltLength (in)	ThreadLength (in)	Weight/100 (lbs)
LR8645	5	3	35
LR8646	6	3	41
LR8647	7	4	44
Lr8648	8	4	51

Clevis bolts

Application

Clevis bolts are used to provide dead end connections to eyes or links. Clevis end includes 1/2” diameter machine bolt with nut and a stainless steel self locking cotter pin to provide a secure vibration proof assembly.

Material

Steel hot dip galvanized

Minimum Tensile Strength 13,500 Ibs

Catalognumber	Size (in)(A×L)	ThreadLength (in)	Weight/100 (lbs)
LR7810	5/8×10	4	172
LR7812	5/8×12	4	192
Lr7814	5/8×14	4	208