该页无缩略图
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
141
⑦ Check the Content of the Modified
Parameter
a) Enter Password Input Mode
Pressing “Modified” in the “Mode
Selection” interface will activate the
Password Input Mode, where user can enter
the Modified Parameter Setting Mode with
the correct password. (For setting the
password, please refer to [2.7.3 Parameter
Encryption].)
b) Enter Modified Parameter Setting
Mode
In this interface, the modified content
of the parameter will be displayed. User can
modify it again in this interface (Here, press
“POP”).
If user wants to restore the modified
parameters, he should press the button with
the name of that parameter (Here, he can
press “Pedal Operation Method”,
“Intermediate Presser Down
Synchronization”) and then click “Restore”.
After that user only needs to follow the
instruction of the system.
If user wants to restore the entire
setting to their default values, he can press
“Restore All”. After that user only needs to
follow the instruction of the system.
2.7.2 Types of Parameter Setting
There are two ways for setting parameter: selection type and input type, as shown below:
Selection Type Input Type
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
142
2.7.3 Parameter Encryption
In the parameter mode, each operation entrance can be attached a password, so as to avoid
the mistake operation.
1 、 Enter Parameter Encryption
Interface：
In main interface P1 (or P2), press
to activate the catalogue mode, and
then press to Enter the
interface for setting functions.
In the function setting interface,
press .
2、Input Password:
Before entering the Parameter
Encryption Mode, user need input
password. (The original password is the
manufacturer ID).
In case of wrong input, pressing
will delete the first figure at the
left of the cursor, while pressing
will delete the entire password inputted.
Input the password and press .
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
143
2、Select Parameter for Encryption：
As shown in the picture, user can
select one or many parameters for
encryption. (Here, we select “Pause”.)
：Selected
：Unselected
After selecting the parameter for
encryption, user can press .
From then on, user has to input
password when setting the parameter
that was encrypted.
For changing password, please
press .
3、Change Password
In the interface of setting new
password,
press
&
in
order and input the current password,
new password, new password
confirmation respectively. At last press
.
[Note]: The original password is the
manufacturer ID. After setting the
password, the current password is the
password set last time.
2.7.4 Recovery and Back-up of Parameters
User can save the changed parameter into U disk for the recovery operation in future.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
144
1、Enter Interface of Parameter
Recovery and Back-up:
In main interface P1 (or P2),
press to activate the catalogue
mode, and then press to
Enter the interface for setting
functions.
In the function setting interface,
press .
2、Back up Parameters
In the interface of parameter
recovery and back-up, the default
setting is to back-up the parameters.
After inserting the U disk, press
. After the operation, the system
will create a catalogue named
“bakParam” in U disk automatically.
The file “backup.param” within that
catalogue is the parameter back-up
file.
[Note]: the file with the same name
will be replaced with new data. The
original data will be lost.
In parameter recovery operation,
user can press to shift to
recovery mode.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
145
3、Parameter Recovery
At recovery mode, press
to recover the parameters. After the
operation, the system will return to
the previous level.
2.7.5 Default Parameter Recovery
User can restore the parameters to their default values. Additionally, user can also save the
set parameters for the usage in future.
1、Enter Default Parameter Recovery:
In main interface P1 (or P2), press
to activate the catalogue mode, and
then press to enter the interface
for setting functions.
In Function Setting Interface, press
and then input the password
(the original password is the manufacturer
ID). With the correct password, user can
enter Default Parameter Mode
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
146
2、Use the Default Parameter
Click the corresponding default
parameter and then press “System Default”
to reload that value
After the reloading, the system will
return to the upper interface automatically.
[Note] Some important parameter, like
“Spindle Motor Stop Angle” cannot be
restored in this operation.
3、Save Customized Parameter
Press “Custom” to enter the interface
for saving parameters, where user can save
the parameter set value.
Click ~
to confirm the
position for saving, and then click to
save it.
After the saving, the system will return
to the upper interface automatically
[Note] The parameter for repair and
maintenance cannot be saved.
[Note] The motor installation angle and
motor parameters can be saved.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
147
4、Load Parameter Saved by User
Enter the Customized Parameter
interface. Check the content on button
“Customized Parameter xx (Y/N)”. If it is Y
in the bracket, it means there is saved
customized parameter.
Click that key and press to
reload the corresponding parameter. After
the operation, the system will return to the
upper interface automatically.
2.7.6 Parameter List
1、Thread Adjuster：
Code Brief Details Unit Step
Length
Range Default
Value
Type
WIP Thread
Adjuster
Switch
Thread adjuster (W)
switch
0:OF:Thread
Adjuster off
1:ON:Thread
Adjuster on
1 Selection
W1 Thread
Adjuster
Start Time
Set the start time of
thread adjuster (W)
according to the
thread-trimming order.
Usually, there is no need
for change.
ms 2 0~998 30 Input
W2 Thread
Adjuster
Work Time
Set the working time of
thread adjuster (W)
according to the
thread-trimming order.
User can prolong the time
if necessary.
ms 2 0~998 30 Input
W3 Thread
Adjuster
Stop Delay
The delay time for the
device return after the
action of thread adjuster
(W)
ms 1 0~255 0 Input
CSS Needle
Thread
Clamp
Device
Needle thread clamp
device switch
OFF
ON
OFF Selection
CRS Needle Needle thread clamp 0~16 8 Input
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
148
Thread
Clamp
Device
Power-on
device power-on
2、Slow Start Stitch：
Code Brief Details Unit Step
Length
Range Default
Value
Type
ST1 Start Speed of
1
st Stitch
Start Speed of 1st
Stitch
100RPM 1 2~27 3 Input
ST2 Start Speed of
2
nd Stitch
Start Speed of 2nd
Stitch
100RPM 1 2~27 5 Input
ST3 Start Speed of
3
rd Stitch
Start Speed of 3rd
Stitch
100RPM 1 2~27 10 Input
ST4 Start Speed of
4
th Stitch
Start Speed of 4th
Stitch
100RPM 1 2~27 15 Input
ST5 Start Speed of
5
th Stitch
Start Speed of 5th
Stitch
100RPM 1 2~27 20 Input
3、Frame：
Code Brief Details Unit Step
Length
Range Default
Value
Type
SYN Sewing When
Frame Is Up
Can the
machine
perform
sewing when
the board is up
0:OF: No
1:ON:Yes
0 Selection
TFS Frame Status at
Sewing End
Frame Status at
Sewing End
0:SUP: Back to
start point and go
up
1:SLU: Go up at
sewing end.
2:SBU: Back to
start point. It goes
up when user steps
pedal.
0 Selection
ATU Frame Auto Up
after Work
After working,
the Frame goes
up
automatically.
0:PUP:Auto UP
1:NUP:Not Auto
Up
0 Selection
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
149
POP Pedal
Operation
Method
Pedal
Operation
Method
0:BUD:Frame
Up/Down
1:IUD: Indirect
Control of Frame
& Help Frame Up/
Down
2:ILR: Indirect
Control of L/R
Frame
0 Selection
LRD Lower Action
of L/R Separate
Frames
Lowering
action of left
presser and
right presser
0:LRU:Down at
Same Time
1:LRN:Left Then
Right
2:RLD:Right Then
Left
0 Selection
LRU Lift Action of
L/R Separate
Frames
Lifting action
of left frame
and right frame
0:LRT: Up after
work
1:LTD:Left Frame
Down after Work
2:RTD: Right
Frame Down after
Work
0 Selection
DYN Special Presser Support
Reverse &
Stretch
Pressers
3- None
4- Reverse
Presser
5- Stretch
Presser
1 0-255 0 Input
PSS Presser Status
at Stop
Presser Status
at Stop
0:UP:Presser
Down
1:DN:Presser Up
0 Selection
OPT
2PE
THG
OPR
OPC
POD
ASD
DSD
4、Range Limitation：
Code Brief Details Unit Step Range Default Type
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
150
Length Value
ALC Cancel Range
Protection
Cancel Range
Protection
0:OF:Protection
Off
1:ON:Protection
On
1 Selection
XL Set Effective
Range in Left
X Direction
Set effective range
in left X direction
mm 1 2~255 101 Input
XR Set Effective
Range in Right
X Direction
Set effective range
in right X direction
mm 1 2~255 101 Input
YU Set Effective
Range in Up Y
Direction
Set effective range
in up Y direction
mm 1 2~255 51 Input
YD Set Effective
Range in
Down Y
Direction
Set effective range
in down Y
direction
mm 1 2~255 51 Input
5、Thread-breakage Detector：
Code Brief Details Unit Step
Length
Range Default
Value
Type
PRT Thread-breakage
Detection
Thread-breakage
Detection
0:OF: OFF
1:ON:ON
0 Selection
ISD Invalid Stitches
at Sewing Start
for
Thread-breakage
Detection
Invalid Stitches at
Sewing Start for
Thread-breakage
Detection
1 0~15 8 Input
IND Invalid Stitches
during Sewing
for
Thread-breakage
Detection
Invalid Stitches
during Sewing for
Thread-breakage
Detection
1 0~15 3 Input
TRM Trim at
Thread-breakage
Detection
Trim at
Thread-breakage
Detection
0:ON: Trim at
Thread-breakage
1:OF: Not Trim
at
Thread-breakage
0 Selection
6、Origin Position：
Code Brief Details Unit Step
Length
Range Default
Value
Type
PTR Return to
Origin at
Power-on
Return to origin at
power-on
0:OF:Not Return
1:ON:Return
0 Selection
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
151
PRF Forbid
Returning to
Origin at
Presser Up
Forbid returning to
origin at presser up
0:OF:Permitted
1:ON:Forbidden
0 Selection
DOG Search Origin
at Sewing
End
Search origin at
sewing end
0:OFF:Not Search
Origin, Stop at
End Point
1:ON:Search
Origin
(Sub-origin)
2:RET:Return to
Sewing Start
1 Selection
RST Set Sewing
Start
Resetting
Path
Set sewing start
resetting path
0:LIN:Linear
Return to Sewing
Start
1:PAT:Return to
Origin along
Pattern
2:ORG:Search
Origin Then
Return to Sewing
Start
0 Selection
DED Select
Highest
Position at
Searching
Origin
Whether to select
highest position at
searching origin
0:OF:Not Select
1:ON:Select
0 Selection
OPA Origin Presser
Action
Origin presser
action
0:DNW:Presser
Down
1:UP:Presser UP
1 Selection
NRM Search/Return
to Origin Path
Path selection of
searching/
returning to origin
0:NRM: Standard
1:REV: Reverse
2:YTX:Y to X
3:XTY:X to Y
0 Selection
REV Search/
Return to
Origin Path at
Reveres
Path selection of
searching/
returning to origin
at reverse
0:NRM: Standard
1:REV: Reverse
2:YTX:Y to X
3:XTY:X to Y
0 Selection
XSP X Axis Sensor
Position
X axis sensor is at
the left or right
side of the head
0:L:Left
1:R:Right
0 Selection
7、Pause ：
Code Brief Details Unit Step
Length
Range Default
Value
Type
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
152
POS Needle
Position at
Pause
Needle position at
pause
0:DWN:Needle
Down
1:UP:Needle Up
1 Selection
ACT Presser
Action at
Pause
Presser action at
pause
0:DWN:Presser
Down
1:UP: Presser Up
0 Selection
TYP Pause
Switch Type
Pause switch type 0:AUT:Auto
Lock
1:NRM:Normal
0 Selection
TRM Auto
Trimming at
Pause
Auto trimming at
pause
0:AUT:Auto
1:OFF:No trim
0 Selection
SYP Security
Switch Type
Security switch
type
NCT: always off
NOT: always on
NCT Selection
8、Counter：
Code Brief Details Unit Step
Length
Range Default
Value
Type
UCM Up Counter
Mode
Up counter
mode
0:OFF:Up Counter Off
1:PAT:Count by
Pattern
2:CYC:Count by Cycle
1 Selection
DCM Down Counter
Mode
Down counter
mode
0:OFF:Down Counter
Off
1:PAT:Count by
Pattern
2:CYC:Count by Cycle
1 Selection
URV Reserve Up
Counter Value
at Inputting
Pattern
Reserve up
counter value
at inputting
pattern
0:CLR:Clear
1:RSV:Reserve
1 Selection
DRV Reserve Down
Counter Value
at Inputting
Pattern
Reserve down
counter value
at inputting
pattern
0:CLR:Clear
1:RSV:Reserve
1 Selection
POC Clear Counter at
Repowering
Clear counter
value at
repowering
0:CLR:Clear
1:RSV:Reserve
1 Selection
NUP Cannot Change
Up Counter
(UP)
Cannot change
up counter
(UP)
0:OF: Permitted
1:ON:Forbidden
0 Selection
NDP Cannot Change
Down Counter
(DN)
Cannot change
down counter
(DN)
0:OF: Permitted
1:ON: Forbidden
0 Selection
UTO Sewing Sewing 0:OF:Stop Sewing 0 Selection
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
153
Machine Action
at Reaching Up
Counter (UP)
Set Value
machine action
at reaching up
counter (up) set
value
1:ON:Continue
Sewing
DTO Sewing
Machine Action
at Reaching
Down Counter
(DN) Set Value
Sewing
machine action
at reaching
down counter
(DN) set value
0:OF:Stop Sewing
1:ON:Continue
Sewing
0 Selection
NPC No Change of
Production
Amount
No change of
production
amount
OFF: Change
Permitted
ON: Change Forbidden
ON Selection
9、Intermediate Presser：
Code Brief Details Unit Step
Length
Range Default
Value
Type
SYN Down
Synchroni
zation
Synchronization of
lowering
intermediate presser
0:BEF: Before
Head Start
1:OUT:Same
with Last Outer
Presser
0 Selection
CUR Intermedia
te Presser
Current
Intermediate presser
current
1 2~8 4 Input
DLY Intermedia
te Presser
Up Delay
Delay the action to
prevent running into
mould
ms 1 0~255 0 Input
TYE Intermedia
te Presser
Type
Select type of
intermediate presser
0:AIR:Air Valve
1:STP: Stepping
2:MAG:Magnet
0 Selection
PLP Intermedia
te Presser
Stroke
Setting
Set intermediate
presser vertical
stroke.
0.1mm 2 0~180 150 Input
ZU8 Intermedia
te Presser
Up Angle
Set up position for
moving intermediate
presser
Degree 1 0~360 100 Input
ZD8 Intermedia
te Presser
Down
Angle
Set down position
for moving
intermediate presser
Degree 1 0~360 0 Input
ZTM Synchroni
zation of
Intermedia
te Presser
Input pattern at
setting intermediate
presser
0:OFF: Not
Relating to
Pattern Input
1:ON: Relating to
1 Selection
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
154
at
Inputting
Pattern Input
PDD Intermedia
te Presser
Down
Delay
Delay at lowering
the intermediate
presser
1 0~255 0 Input
MSP Intermedia
te Presser
Moving
Speed
Set the moving
speed of
intermediate presser
when CUR=8
8-17 13 Input
10、Winding：
Code Brief Details Unit Step
Length
Range Default
Value
Type
SPD Winding
Speed
Set wind speed 100RPM 1 2~27 13 Input
STP Winding
Device Stop
Method
Set method to
stop winding
0:UTS: Release
Pedal to Stop
winding
1:RTS:Step Pedal
again to stop
winding
2:TTS: Set Time
to Stop Winding
1 Selection
TPD Set Stop
winding time
(Unit Second)
Set the time to
stop winding
(Unit Second)
s 2 2~498 30 Input
11、Feed Method：
Code Brief Details Unit Step
Length
Range Default
Value
Type
TYP Pressing Board
Type
Select Pressing
Board
0:AIR:Air-driven
1:MAG: Magnet
2ADP:
Self-adopt
0 Selection
WEI Weight of
Pressing Board
Select the weight
of pressing board
0:HIG: Light
1:MID:Middle
2:WEG:Heavy
1 Selection
HIG Light Board
(Air Amount
L)
Light board (Air
Amount L)
1 0~255 145 Input
MID Middle Board
(Air Amount
M)
Middle board
(Air Amount
M)
1 0~255 0 Input
WEG Heavy Board Heavy board 1 0~255 0 Input
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
155
(Air Amount
H)
(Air Amount
H)
STP Sewing Type
Selection
Select sewing
type
0:TIN:Thin
1:MID:Middle
2:TIC:Thick
0 Selection
THI
N
Thin Fabric Thin fabric
thickness
1 0~255 0 Input
MID Middle Fabric Middle fabric
thickness
1 0~255 0 Input
THC
K
Thick Fabric Thick fabric
thickness
1 0~255 0 Input
SUI Pattern-making
Follows Action
Setting
Pattern-making
follows the
action setting
0:OF: Forbid
1:ON: Permit
1 Selection
SMD Start
Frame-moving
Angle
Adjustment
Adjust the start
frame-moving
angle
Degree 1 -50~+50 0 Input
STD End
Frame-moving
Angle
Adjustment
Adjust the end
frame-moving
angle
Degree 1 -50~+50 0 Input
SAE Frame-moving
Initial Angle
Setting
Set the initial
frame-moving
angle with speed
over 1800rpm
Degree 1 135-280 135 Input
MM
D
Move Mode XY axis action
mode
0:ETM: Equal
Time
1:NTM: Unequal
Time
0 Selection
12、Speed：
Code Brief Details Unit Step
Length
Range Default
Value
Type
HSP High Speed Set high speed 100RPM 1 2~27 23 Input
LSP Low Speed Set low speed 100RPM 1 2~27 2 Input
MHS Middle High
Speed
Set middle high speed 100RPM 1 2~27 15 Input
MLS Middle Low
Speed
Set middle low speed 100RPM 1 2~27 10 Input
EDL Feed Delay Delay after feeding
action
1 0~9999 0 Input
JDL Step Moving
Delay
Delay after step
moving action
1 0~9999 0 Input
IDL Pattern-making Delay after 1 0~2700 0 Input
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
156
Delay pattern-making action
SEW Sewing Speed Set sewing speed 1 0~9 4 Input
FED Feed Speed Set speed at empty
feed section
1 0~9 4 Input
FRM Frame-moving
Speed
Set frame-moving
speed
1 1~3 3 Input
SPS Returning to Start
Point Speed
Set speed for
returning to the start
point
1 0-9 4 Input
HPS Search Origin
Speed
Set speed for
searching origin
1 5~10 5 Input
SMS Single Step Move
Speed
Set speed of moving
of single step
1 0~40 30 Input
13、Thread-trimming Order：
Code Brief Details Unit Step
Length
Range Default
Value
Type
TRM Trimming Switch Trimming
Switch
0:OFF:Off
1:ON:On
1 Selection
SPD Trimming Speed Trimming
Speed
10RPM 1 20~40 40 Input
ANG Needle Position
Angle After
Trimming
Needle
position angle
after
trimming
0:UP:
Upper
Needle
Position
1:DED:
Upper
Dead
Point
0 Selection
DLY Thread-trimming
delay
Thread-trimm
ing delay
0.01s 1 0~255 12 Input
TST Trimming Output
Start Time/
Angle
Trimming
output start
time/ angle
mm/
Degree
2 0~998 210 Input
TET Trimming Output
End Time/ Angle
Trimming
output end
time/ angle
mm/
Degree
2 0~998 0 Input
TMD Trimming Mode Select
thread-trimmi
ng order
0:FST:fast
1:GEN:Ge
ntle
1 Selection
OPT Thread-loosing
Delay
Thread-loosin
g delay
1 0~255 0 Input
OSA Thread-loosing
Start Time/Angle
Thread-loosin
g start
time/angle
mm/
Degree
2 0~998 300 Input
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
157
OEA Thread-loosing
End Time/Angle
Thread-loosin
g end
time/angle
mm/
Degree
2 0~998 0 Input
14、LCD Screen：
Code Brief Details Unit Step
Length
Range Default
Value
Type
WRN Warning of
Buzzer
Set the warning voice
of buzzer
0:OFF: No Voice
1:PAR:Panel Voice
2:ALL:Panel +
Warning Voice
2 Selection
DEL Touching
Panel
Sensitivity
Adjustment
Adjust sensitivity of
touching panel
1 1~5 3 Input
LIG Back Light
Adjustment
Adjust the back light 1 20~100 100 Input
ATO Back Light
Auto
Turn-off
Auto turn-off of back
light
0:OF:Not Auto
Turn-off
1:ON:Auto
Turn-off
0 Selection
TIM Back Light
Auto
Turn-Off
Waiting Time
Time for waiting auto
turn-off of back light
Minute 1 1~9 3 Input
BTN Button
Display Style
Set the display style of
the button in Test
Mode and Function
Mode
0:ICN: Icon
1:TXT: Text
0 Selection
BKC Background
Color Setting
Set the background
color of the pattern
display area in main
interface
0：Block
1：Dark Blue
2：Red
3：Green
4：Blue
5：Purple
6：Yellow
1 0~6 0 Input
SES Display Style
of Pattern
Selection
Set the display style of
pattern-selection
interface
Note: only the used
patterns can be
0:CLS:Classic
(Display Number
List)
1:SHP: Display
Pattern Shape
0 Selection
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
158
displayed.
ZST Scaling
Method
Scaling Method SQA: square
L-W: length-width
SQA Selection
RBS Return to
Sewing Start
Hotkey
Return to sewing start
hotkey
OFF
ON
OFF Selection
DPN Display
Needle Drop
Point
Whether to display
needle drop point
NO
YES
NO Selection
CCS Continuous
Sewing of
Combination
Pattern
Whether to sew
combination pattern
continuously
NO
YES
NO Selection
LPT Support
Pattern of
Large
Number of
Stitches
Support pattern of
large number of
stitches
OFF
ON
OFF Selection
SCS Main
Interface
Function
Hotkeys
Whether to display the
function hotkeys on
the main interface
OFF
ON
ON Selection
CSM Pattern
Transforming
Method
Set the pattern
transforming method
STI: stitch
ELE: element
STI Selection
PSU Scaling Unit Set the scaling unit %: percentage
SIZ: size
% Selection
MSM Scaling
Method for
Multiple
Sewing
Set the scaling method
for multiple sewing
VAR: variable
interval
FIX: fixed interval
VAR Selection
PMR Return after
Modification
Set the return method
after finishing
modification
FUN: function
selection
CNT: continue
modification
FUN Selection
OFM Multiple
Sewing,
Deviating
Sewing
Modification
Method
Set the modification
method for multiple
sewing and deviating
sewing
REL: relative
modification
ABS: absolute
modification
REL Selection
15、Others：
Code Brief Details Unit Step
Length
Range Default
Value
Type
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
159
NLD Needle-cooling Needle cooling
device
0:OFF:No
1:ON:Yes
0 Selection
PEM Permission of
Single Pedal
Operation
Permission of
single pedal
operation
0:OFF:
Forbidden
1:ON:
Permitted
0 Selection
LAG Language
Selection
Language
selection
0:CH:中文
1:EN:English
0 Selection
SSW Sound Setting Set sound
function
0:OFF:Off
1:ON:On
1 Selection
VOL Volume of
Operation Voice
Volume at
pressing button
30~63 50 Input
NSW Network
Connection
Activate the
network
connection
0:OFF:Off
1:ON:On
0 Selection
LED LED Brightness For machine
with LED
output, set the
brightness of
LED
0-100 50 Input
DLY Thread Loosing
Device Open
Delay When
Threading
When threading,
the opening time
of the thread
loosing device
when the
intermediate
presser goes
down
S 0-255 0 Input
CUR Thread Loosing
Device Open
Current When
Threading
The value of the
thread loosing
device open
current when
threading
0-255 0 Input
SEC Automatically
Add Sub-origin
after First Empty
Feed
Whether to add
sub-origin
automatically
after the first
empty feed
OFF
ON
OFF Selection
SEC Whether
Intermidiate
Presser Moves
Along with
Pattern-designing
Edit whether
intermediate
presser moves
along with
pattern-designing
OFF
ON
ON Selection
MAH Applicable to Set the 0-10 0 Input
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
160
Machine Type
with Automatic
Feed Function
parameters of
machine type
with automatical
feed function
DSP Start Delay after
Stepping Pedal
Set the
activiation of
start delay after
stepping pedal
OFF:
prohibited
ON: allowed
OFF Selection
DEP Start Delay Time
after Stepping
Pedal
Set the start
delay time after
stepping pedal
0~200 0 Input
FEP Empty Feed
Stitch Length
Set the stitch
length when
empty feed
mm 10~120 12 Input
PTP PLT Switch
Stitch Length
Setting
Set the PLT
switch stitch
length
10~127 30 Input
16、Repair & Maintenance：
Code Brief Details Unit Step
Length
Range Default
Value
Type
NRT Needle
Replacement Left
Value
Left stitches for
needle replacement
1000
Stitch
1 0~9999 0 Input
NST Needle
Replacement Set
Value
Set stitches for
needle replacement
1000
Stitch
1 0~9999 0 Input
HRT Clearing Time
Left Value
Left hours for
clearing
Hour 1 0~9999 0 Input
HST Clearing Time Set
Value
Set hours for
clearing
Hour 1 0~9999 0 Input
ORT Oil Replacement
Left Value
Left hours for oil
replacement
Hour 1 0~9999 0 Input
OST Oil Replacement
Set Value
Set hours for oil
replacement
Hour 1 0~9999 0 Input
BLR Bobbin Thread
Replacement
Residual Value
(Stitch Number)
Click in, but unable
to input
BLS Bobbin Thread
Replacement Set
Value (Stitch
Number)
Bobbin thread
replacement set
value
0~6000 0 Input
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
161
OLI Oiling Interval
Time
Oiling interval time S 0~999 0 Input
OLW Oiling Work Time MS 0~9999 0 Input
[Note]: Parameters, like NRT, HRT and ORT can not be set. User can only check them in
the Internal Parameter Setting Interface
[Note]: After the modification of parameters for repair and maintenance, the
corresponding parameters of “Left Value” will be changed to the set value
[Note]: After the parameter value of repair and maintenance are set (value over 0), the
corresponding counting function for repair and maintenance will be activated as well.
17、Special：
Code Brief Details Unit Step
Length
Range Default
Value
Type
HSP Max Speed Max Speed 100RPM 1 2~27 23 Input
MAE Main Stop
Angle
Stop angle of
main shaft
motor
Degree 1 30~80 53 Input
DEB Letter
Embroidery
Activate letter
embroidery
0:OF:Turn off Letter
Embroidery
Function
1:ON: Turn on
Letter Embroidery
Function
1 Input
DAE Upper Dead
Point Angle
Set angle
from stop
point to upper
dead point
Degree 1 0~50 3 Input
RSC Stitch
Length
Deceleratio
n Curve
Select built-in
stitch length
deceleration
curve
1 0-6 5 Input
HSL Max Stitch
Length at
Keeping
Speed
Max stitch
length at
keeping
highest speed
0.1mm 1 1-127 0 Input
MTS Main Shaft
Motor Type
Selection
Support
550W &
750W
0-550W
1-750W
1 Selecti
on
xDIR X Motor
Rotation
Direction
Switch X-axis
stepping
motor
rotation
direction
POS: positive
direction
NEG: negative
direction
POS Select
ion
yDIR Y Motor
Rotation
Switch Y-axis
stepping
POS:正向
NEG:反向
POS Select
ion
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
162
Direction motor
rotation
direction
zDIR Z Motor
Roatation
Direction
Switch Z-axis
stepping
motor
rotation
direction
POS: positive
direction
NEG: negative
direction
POS Select
ion
ADR Main
Control
Burned-in
Address
The write-in
address of the
main control
update
program
stored in the
U disk
655360
~917504
917504 Input
CVE Parallel
Cureve
Algorithm
Set the
parallel curve
generated
during pattern
edition
A1: algorithm 1
A2: algorithm 2
A1 Select
ion
MUS Reverse
Sewing
Algorithm
under
Multiple
Sewing
Set the
reverse
sewing of
multiple
sewing during
pattern
eddition
ALL: by section
SE: end to end
ALL Select
ion
TID Pattern
Recognizati
on Setting
Pattern
recognization
setting
OFF
ON
OFF Select
ion
PFT Pattern
Correspondi
ng No.
Section
0~9
0:001~031
1:101~131
2:201~231
3:301~331
4:401~431
5:501~531
6:601~631
7:701~731
8:801~831
9:901~931
0 Input
PXO X Diviation
of Marker
X diviation of
marker
-500~500 0 Input
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
163
PYO Y Diviation
of Marker
Y diviation of
marker
-200~200 0 Input
PSP Marker
Running
Speed
Marker
running speed
1~9 1 Input
TTY Pattern
Recognizati
on Device
Pattern
recognization
device
SEN: sensor
BAR: bar-code
scanning device
SEN Select
ion
ICS Communica
tion Speed
Improveme
nt
Communicati
on speed
improvement
OFF
ON
OFF Select
ion
2.8 Test Mode
In main interface P1 (or P2),
press to activate the
catalogue mode, and then press
to enter the test mode.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
164
Functions：
No. Functions Content
A LCD Test Test LCD displayer
B Touching Screen Correction Correct the touching screen
C Input Signal Test Test the input signal of switches and sensors
D Speed Test Test the speed of main shaft motor
E
Main Motor Installation
Angle Adjustment
Display and set the installation angle of main shaft motor
F XY Motor Origin Test Test the motor origins of X /Y motors
G Continuous Running Set continuous running parameter and enter aging status
H
Intermidiate Presser
Function Test
Used to test intermediate presser
I Quit Quit test mode and return to main interface
J Network Setting Set the relating parameters of network
K Output Signal Test Test the output signal of pressers and thread-trimming devices
2.8.1 LCD Test
Function：
In the test mode, press
to activate LCD test function. Click
the area other than to have
LCD screen display white, black, red,
green and blue so that user can judge
whether the LCD screen has problem.
Press to return to the
upper level interface.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
165
2.8.2 Touching Screen Correction
Functions：
Under test mode, press
to display the interface for ID input, as
shown on the right. Then input the ID
and press to enter touch screen
correction function.
User has to correct 5 spots. The
touching pen is recommended to be
used at touching the cross icon on the
interface. After the correction, the
system will display the result of this
operation
[Note]: During the correction, please
perform the operation strictly
according to the position of the cross
icon, otherwise the touching screen
may be unable to be used normally
after the correction.
2.8.3 Input Signal Test
Function：
In the test mode, press
to activate the Input Signal Test
Function.
ON：Activation
OFF：Deactivation
Types of Input Signal：
① Start switch (Pedal)
② Presser switch (Pedal)
③ Pause Switch
④ Thread-breakage Detection
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
166
⑤ X Motor Sensor
⑥ Y Motor Sensor
⑦ Intermediate presser origin
⑧ Security switch
⑨ External input 1 (PORG)
⑩ External input 2 (PSENS)
⑪ External input 3 (CORG)
⑫ External input (CSENS)
⑬ External input (AORG)
⑭ Three-in-one Pedal
Press to return to the upper
level interface.
2.8.4 Main Shaft Speed Test
Functions：
In the test mode, press
to enter the main shaft speed test
function.
Use and to set the
aim speed of main shaft motor. After
user presses , the main shaft motor
will rotate at the set speed. At this
moment, the actual speed will be
displayed in the input column of actual
speed.
Press to stop running
Press to return to the upper
level interface.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
167
2.8.5 Output Signal Test
Functions：
In the test mode, press
to activate the output signal test
function.
In this interface, user can press
output signal button to test the status of
output signals of solenoids
Types of Output signals：
① Thread-wiping
② Thread-trimming
③ Presser
④ Intermediate presser
⑤ Thread-loosing
⑥ Reverse Presser
⑦ Auxiliary air valve 1
⑧ Auxiliary air valve 2
⑨ Auxiliary air valve 3
⑩ Auxiliary air valve 4
⑪ Auxiliary air valve 5
Press to return to the upper
level interface.
[Note]: The sewing machine will
have the actual movement.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
168
2.8.6 Continuous Running
Function：
In the test mode, press
to enter the continuous running
function
Click Action Interval bar or
Origin Detection of
Needle-withdrawing bar and use
number keys to input the figures. Press
to return to the upper level
interface.
There are two ways to activate the
aging status: pedal or origin; after
setting this parameter, return to main
interface P1 (or P2). Step pedal or
press the Return to Origin key to run
the machine, and enter continuous
running mode.
2.8.7 XY Motor Origin Test
Functions:
In the test mode, press
to activate the XY Motor Origin
Detection Function.
In this interface, use direction keys
to move XY motor. During this process,
the system will display the ON/OFF
status of the sensors.
ON：Sensor Detected
OFF：Sensor Undetected
Press to return to the upper
level interface.
[Note]: The sewing machine will have
the actual movement.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
169
2.8.8 Main Motor Installation Angle Adjustment
Functions：
In the test mode, press
to enter the main motor installation
angle adjustment.
In the current interface, remove
the main motor, turn the hand wheel to
lift the needle bar to the highest point
and turn the main shaft joint to adjust
the electrical angle within less than 30
degree. After that, reinstall the main
motor and press to confirm.
2.8.9 Network Setting
Functions：
In the test mode, press
to enter the network setting function. If
user needs the network function of
operation panel, he should set the
relating parameters of network.
Use number keys to input
parameters, make sure the “IP
Address” and “Server IP” are within
the same section. Use and
to move the cursor. After
finishing the setting, press the
Connection key to get connected with
the computer via internet.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
170
2.8.10 Intermediate Presser Test
2.9 Function Setting
In main interface P1 (or P2), press
to activate the catalogue mode,
and then press to enter the
Function Setting Mode.
Functions：
In the test mode, press
to enter intermediate
presser test.
:Intermediate Presser Down
:Intermediate Presser Up
:Shift Intermediate Presser
Position
[Note]: In this interface, step
pedal to return the intermediate
presser to origin (the highest
position of intermediate presser);
the highest point is 71mm, middle
point is 35mm, and the lowest point
is 0mm. The adjusted position is the
fabric thickness.
This function is only available
for G Type.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
171
Functions：
No. Functions Content
A Data Transfer Transfer pattern file between memory and U disk
B Formatting Initialize the U disk, memory and pattern number hotkeys.
C Pattern Connection Edit combined pattern
D Version Inquiry Inquire the version of system software
E Display Setting Set background light, keyboard lock, lightness and so on
F
Back-up Parameter
Recovery
Save parameter values into U disk for the parameter
recovery in future
G Default Parameters
Recovery and self-defined read-write function of the
default parameter values
H
Pattern Number Hotkey
Edition
Edit the content of pattern number hotkey
I Password Mode Provide periodical password function
J Parameter Encryption
Set passwords for each operation entrance in parameter
mode.
K Quit Return to main interface
L Motor Configuration Enter main motor, stepping current configuration mode
M Alarm Record Check the alarm statistic information
N Running Record Check running information of machine
N Date & Time Setting Set data and time
O Time Setting Set the date and time
P Software Update Enter software update mode
Q
Shift between Icon and
Description
Shift between the icon and description of the hotkeys
R Player Play audio in the formats of mp3, AVI, etc.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
172
S
Pattern Transformation in
Batch
Change the patterns of non-standard formats into standard
formats. Note: standard format means nsp format.
T Hotkeys Setting
Edit and display hotkeys in the main interface for
convenient operation by the users according to their habits
2.9.1 Data Transfer Mode
In function setting interface, press to enter data transfer mode, where two ways
are provided: “Memory to U Disk” and “U Disk to Memory”
Functions：
No. Description
A Page information, displaying the present page/total pages
B Pattern List
C
：Memory Pattern List
：U Disk Pattern List
D Select All Patterns
E Delete Pattern
F Quit and Return to Upper Interface
G Page Key
H
Load pattern from memory or U disk
：Activate the Memory Load Mode: At this moment, user cannot load
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
173
Operation：
1、Copy Mode Selection
The default setting is to copy pattern from memory to U disk, user can press to
change the copy mode.
2、File Selection
Select the pattern for copy from the pattern list (here, we select No.400, 401 and 600). If the
patterns are so many, please use to turn the page.
For copying all the patterns, please press and please press to delete
patterns.
3、Confirm the Copy
After selection, please press and then the system will display “Copy the Selected
pattern from U disk.
：Deactivate the Memory Load Mode: At this moment, user can load
pattern from U disk.
：Activate the U Disk Load Mode: At this moment, user can not load
pattern from memory.
：Deactivate the U Disk Load Mode: At this moment, user can load
pattern from memory.
：Shift between U Disk and Memory
I Display the file folders of the U disk
J Enter
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
174
Pattern”, where user can press to perform the operation. If the pattern is copied from
memory to U disk, the system will automatically create a catalogue naming “dh_pat” at the base
catalogue of U disk and save the pattern under that catalogue.
[Note]: During the copy process, if the memory contains the pattern with the number same
to that of the pattern in the U disk, the new pattern will replace the old one.
2.9.2 Formatting Mode
In function setting interface, press
to activate formatting mode
There are four formatting methods
in this interface: USB formatting,
Memory formatting, Self-defined
formatting and Pattern number hotkey
formatting
12、 USB Formatting：
Press “USB” to delete all the patterns in the U disk. So user need back up the data if
necessary.
2、Memory Formatting：
Press “Memory” to delete all the patterns in the memory.
[Note]: After the memory formatting, pressing will have system display “Pattern Not
Found in Memory”. Pressing will automatically load the default patterns.
3、Self-defined Formatting：
Press “Self-defined” to enter the
interface for Self-defined formatting
In that interface, user can delete
all patterns or selected patterns.
[Note]: The pattern being sewn can
not be deleted.
4、Hotkey Formatting：
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
175
Pressing “Hotkey” to delete the content of the hotkeys of pattern number.
[Note]: After the hotkey formatting, pressing will have system display “Pattern List
(Hotkey) Is Empty”. Pressing will automatically load the current pattern number to
the hotkey.
2.9.3 Pattern Connection Mode
In function setting interface, press to enter Pattern Connection Mode. The
pattern connection mode is mainly used to create and edit the combined pattern, which is to
perform the combination edition on the basis of the existing patterns. The pattern used in
combined pattern is called as sub-pattern.
Function：
No. Description
A Name of Combined Pattern
B Page
C Load Combined Pattern
D Save Combined Pattern
E Display Sub-pattern
F Quit & Return to Previous Interface
G Page Key
H Add Pattern from Memory to Combined Pattern
I Delete Sub-pattern
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
176
Operation：
1、 Select a Sub-pattern
Press to enter Load Mode
and select the pattern to add (select
pattern No.612 as an example). Press
to confirm it.
[Note]: Patterns should be added to
the combined pattern in order.
2、 Continue Adding
Repeat the above operation to add
more sub-patterns (Add patterns
No.600, 602 and 401)
If user wants to delete one of
them, please select the number of the
sub-pattern and then press .
J Cancel Combined Pattern
K Enter
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
177
3、 Save the Combined Pattern
Press to enter the mode for
saving combined pattern.
Name the combined pattern and
press to confirm it. For other
operations within this interface, please
refer to [2.6 Save Pattern].
4、 Return to Main Interface
After finishing edition of the
combined pattern, press to
return to main interface.
As shown in right figure, there are
some differences between the
combined pattern sewing interface
and the normal pattern sewing
interface.
① The name of combined pattern
is displayed behind the number and the
name of the current sub-pattern will be
displayed at the name area.
[Note]: If the combined pattern has
no name, nothing will be displayed.
② The original pattern number
hotkeys will display the sub-patterns in
this combined pattern. Click the
sub-pattern to start the sewing from
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
178
that sub-pattern.
5、 Cancel the Combined Pattern
In order to cancel the combined
pattern, user has to enter the pattern
connection mode again, presses
and clicks .
6、 Load Combined Pattern
In pattern connection mode, if
user presses when the combined
pattern exists, the system will display
“Clear Current Combined Pattern”.
Clicking will clear the current
combined pattern.
Press again to enter the
interface for loading the combined
pattern, where users can select the
combined pattern for sewing or editing.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
179
2.9.4 Version Inquiry Mode
In function setting interface, press
to enter version inquiry
mode.
Press to output the software
version to the base catalogue of the U
disk with name “version.png”.
2.9.5 Display Setting Mode
In function setting interface, press
to enter display setting
mode, where user can perform the
settings about the display, operation
and so on.
1、Backlight Auto Turn-off
By the set time, the screen backlight will be turned off automatically.
Range：1～9 min
Default Value: Invalid
Releasing Method: if the backlight is off, user can touch any position of the screen to turn it
on.
2、 Keyboard Lock
When it is set as “Valid”, all the buttons will turn to grey in display and become useless.
Pressing will directly return to main interface P1.
Default Value: Invalid
Releasing Method: Hold the title bar at main interface P1 for over 5 seconds, until user hear
“Bee--m”. After that the lock is released. (After the releasing, this function will be set as Invalid.)
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
180
3、 Turn off Buzzer
When it is set as “Valid”, system will keep silence when user presses button.
Default Value: “Invalid”
4、 Sensitivity of Touching Panel
Adjust the sensitivity of the touching panel. The larger value means the higher sensitivity
Range：1～5
Default Value：3
5、 Lightness Control
Adjust the lightness of the LCD screen. The larger value is, the lighter will be
Range：1～100
Default Value：100
6、 Button Display Style
Set the display style of some buttons. After the successful setting, the button display under
interfaces of “Catalogue Mode”, “Test Mode” and “Function Setting” will be changed
Range：0~1（0：Icon，1：Text）
Default Value：0
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
181
7、 Background Color Setting
Set the background color of the pattern display area in main interface
Range：0~6 (0:Black, 1: Dark Blue, 2: Red, 3: Green, 4: Blue, 5: Purple, 6: Yellow)
Default Value：0
8、 Display Style of Pattern Selection
Set the display style of the interface for loading patterns. Only the used patterns can be
displayed.
Range：0~1 (0: Number, 1: Shape)
Default Value：0
Please refer to [2.5.5 Display Style of Pattern List]
9、 Panel Display Style
Adjust the panel display style
Range：0~2（0：plastique，1：cleanlooks，2：windows）
Default Value：0
10、 Position of Assistant Information Bar
Set the position of the assistant information bar
Range：0~1 (0：Right, 1：Left)
Default Value：0
[Note]: After the setting, user has to restart the system
11、 Main Interface Background Color
Set the background color of the main interface
Icon Style Display Text Style Display
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
182
Press “Setting” to open the color board.
Select the color and press “OK” to
confirm and turn off the color board
At this time, the color display area will
show the selected color. Press to return
to the main interface P1 directly and change
the background color of the main interface.
12、 Background Color of Assistant Information Bar
Set the background color of assistant information bar. The operation is same as above.
13、 Speed Setting in the Main Interface
The speed can be set by level or by value.
14、 LED Lightness Adjustment
The adjustment range is 0~100.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
183
2.9.6 Back-up Recovery Mode
In function setting interface, press
to enter back-up recovery
mode.
User can save the value of
changed parameter into the U disk for
the parameter recovery in future.
For details, please refer to [2.7.4
Recovery and Back-up of Parameter]
2.9.7 Default Parameter Mode
In function setting interface, press
to input the password (the
original password is the manufacturer
ID). After the input of password, the
system will enter Default Parameter
Mode.
It is used to recover the default
parameters and to save the parameter
values for future.
Please refer to [2.7.5 Default
Parameter Recovery] for details
2.9.8 Pattern Hotkey Management Mode
In function setting interface, press
to enter Parameter Hotkey
Management Mode, where user can
edit the pattern number hotkeys.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
184
1、 Input Pattern Number and
Select the Position of Hotkey for
Editing
Please refer to [2.5.1 Direct Load
Mode]. User can input the number to
find the pattern, if he knows that
number.
Then select the position of edition
in the hotkey display area (We select
the third blank)
2、 Edit the Hotkey
Select a pattern number in the
pattern list, then that number will be
displayed at the position that we
selected in the previous operation.
User can also add the pattern at
the position that already has a pattern
in the hotkey list. This is to insert a
number at this position. The numbers
after will be moved correspondingly.
[Note]: If the pattern number for
adding has already existed in the
hotkeys, the system will adjust its
position to the location that is closest to
the selected position
3、 Deletion and Formatting
Select a pattern number in the
hotkey display area and press
to delete that number. Then the system
will automatically adjust the number
position in the hotkey list.
Press to delete all the
number in the list.
[Note]: After the hotkey formatting,
pressing will have system
display “Pattern List (Hotkey) Is
Empty”. After confirming the
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
185
operation the system will
automatically load the current
pattern number to the hotkey.
2.9.9 Password Mode
In function setting interface, press
to activate the interface for
inputting the user ID. Input the correct
manufacturer ID to enter the password
management mode, where user can set
and manage the periodical password.
② At most 10 different
password action times can be set.
② System can display the
password information of the
manufacturer.
1、 Input Board Number
Press “Board Number” to enter
the interface for inputting the board
number. The board is formed by four
figures, the range is from 0000 to 9999.
This can be used for the management
of the password by the manufacturer.
After inputting the board number, user
can press to finish the operation
and return to the previous interface.
(Here, we input 0001 as the board
number).
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
186
2、 Confirm the System Clock
Press “Clock” to enter the
interface for setting system time and
date. For changing the system clock,
user need press after the
modification (Refer to [2.9.14 Date and
Time Setting Mode], or press to
quit.
3、 Input the Super Password
Press “Super Password” to enter
the interface for inputting the super
password.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
187
At most 9 figures can be inputted,
which are displayed as “·”. After user
presses , the system will ask user
to input that password again for
confirmation.
If the inputted passwords in these two
times are different, the system will ask
user to input the super password again.
After these two inputted passwords
agree, user can press to save it
and quit.
4、 Input Activation Time and
Periodical Password
Press “pw-1” to input the first
activation date.
The activation date is the first
time when the password is activated.
This date shall be later than the system
date.
Select the proper date and press
to finish the operation. At this
moment, the system will turn to
password input interface
The input method of the
periodical password is the same as that
of the super password. After the
confirmation, press to quit.
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
188
5、 Continue Inputting Periodical
Password
If user need input the next
activation date and password, he
should repeat the above operation. At
most, ten dates and passwords can be
inputted.
[Note]: The next date shall be later
than the previous one.
6、 Save Password
Input the needed password, and
then press to save the entire
information. The system will display
“Password Saved Successfully”.
After confirmation, the system
will return to the previous interface.
[Note]: Only when user set at least
one periodical password, can
be displayed.
7、 Clear Password before
Activation
Clearing password is to delete the
password before it activates.
The method for entering the
password display interface is the same
as that of password setting
After user input the right
manufacturer ID, the system will
display the current time and activation
dates of periodical passwords, as
shown in right figure
Press to input the current
password. The password is cleared in
order of from front to behind.
Operation Instructions 4XX Pattern Sewing Machine (Touch Panel H)
189
At this moment, user can input
two passwords. If the inputted
password is the current password, the
current password will be deleted. If the
super password is inputted, the entire
password will be deleted. If the current
password is deleted and the current
password is the last password, the
system will have no password any
more. Press to finish the
operation.
The deleted password will display
in red color as shown in the right
picture. If the entire password is
deleted, the system will return to the
upper level interface.
8、 Clear Password at Activation
If the system has the password
and that password is not canceled, the
password will activate at the set date.
At this moment, user has to input the
effective password to have the machine
continue to work normally.
The effective passwords include
the current password and the super
password. If the inputted password is
the current password, the current
password will be deleted. If the super
password is inputted, the entire
password will be deleted. If the
password is current password and the
current password is the last password,
the system will have no password any
more. If the machine still have other
password other than the current
password, the next password will
activate according to the set date
4XX Pattern Sewing Machine (Touch Panel H) Operation Instructions
190
2.9.10 Parameter Encryption Mode
In function setting interface, press
, then system will ask for the
password (default password is
manufacturer ID). Input the right
password to enter the parameter
encryption interface.
For details, please refer to [2.7.3
Parameter Encryption]
2.9.11 Motor Configuration Mode
In function setting interface, press
, then system will ask for the
password (default password is
manufacturer ID). Input the right
password to enter the motor
configuration interface.
