该页无缩略图
9.5.2.6 Brake switching times
Switching times in case of brake operation with nominal voltage Switching times in case of brake operation with overexcitation voltage
t11B
t1B t2B
0,1 x M1Bstat
M1Bstat
M
ML*
U
UN,B
t
t
t11B
t1B t2B
0,1 x M1Bstat
M1Bstat
M
U
UholdB = UN,B
t
t
UO,B
tO,B
ML*
9.5.3 Installation conditions
The torque and force values listed in this catalog are valid under the following conditions:
• When the flange shaft and gear housing are fastened on the machine side using screws of strength class
12.9
• When the gear housings are adjusted at pilot øb1. The machine-side fit must be H7.
• When the flange shaft is adjusted using the connecting element at pilot øbf or ødf
9 PHQK right-angle planetary gear units 9.5 Product description
251
9.5.4 Mounting positions
The following table shows the standard mounting positions.
The numbers identify the gear unit sides. The mounting position is defined by the gear side facing downwards.
PHQ5K1 − PHQ8K4
EL1 EL2 EL3
EL4 EL5 EL6
9.5 Product description 9 PHQK right-angle planetary gear units
252
PHQ9K5 − PHQ12K9
EL1 EL2 EL3
EL4 EL5 EL6
Since the lubricant filling volume of the gear unit depends on the mounting position, the mounting position
must be specified when ordering.
9.5.5 Lubricants
STOBER fills the gear units with the amount and type of lubricant specified on the nameplate. The filling volume and the structure of the gear units depend on the mounting position.
Only install the gear units in the intended mounting position! Reposition the gear units only after consulting
STOBER. Otherwise, STOBER assumes no liability for the gear units.
You will receive lubricants for use in the food industry upon request.
9 PHQK right-angle planetary gear units 9.5 Product description
253
9.5.6 Position of the terminal box/plug connector
Mounting position EL1
Terminal box/plug connector in 270° position (standard)
Mounting position EL4
Terminal box/plug connector in 270° position (standard)
Indicate variations for your gear unit in the order.
Note that the terminal box/plug connector position rotates along with the gear unit if the geared motor is in
another mounting position.
9.5.7 Other product features
Feature Value
Max. permitted gear unit temperature (on the surface of the gear unit) ≤ 90 °C
Paint Black RAL 9005
Explosion-proof design in accordance with (ATEX) Directive 2014/34/EU
(optional)
Not available
Efficiency:
ηget three-stage
ηget four-stage
ηget five-stage
93%
92%
90%
Protection class: 1
IP65
9.5.8 Direction of rotation
Output side 4 Output side 3
The pictures show mounting position EL1.
9.6 Project configuration
Project your drives using our SERVOsoft designing software. Download SERVOsoft for free at https://
www.stoeber.de/en/ServoSoft.
It is the most convenient and reliable method of drive selection, as the entire torque/speed curve of the application is displayed and evaluated here in the curve of the geared motor.
1
Observe the protection class of all the components.
9.6 Project configuration 9 PHQK right-angle planetary gear units
254
In this chapter, only limit values for specific operating points can be taken into consideration for manual
drive selection.
An explanation of the formula symbols can be found in the chapter Formula symbols.
9.6.1 Drive selection
The formula symbols for values actually present in the application are marked with *.
Safety-relevant
gravity-loaded axis?
Yes No Drives must be
selected together
with STOBER for
safety reasons.
Determine the gear unit size
Determine the actual acceleration
torque M2acc* and the actual
equivalent torque M2eq* at the
gear unit output 2N
2eq* op t M
M
fB fB
£
×
Choose a gear ratio and determine the
actual average input speed n1m* and
the actual maximum input speed n1max* 1maxDB
1m* T n
n
fB
£
1max ZB
1max* T n
n
fB
£
Determine the actual
emergency off torque M2NOT*
M2NOT* £ M2NOT
Gear unit selection ended
Ex operation
441677_en
Select a
larger gear unit
Select a smaller gear ratio
and, where appropriate, a
larger motor
No
No
Select a
larger gear unit
No
No
Yes
No
Yes
Yes
Yes
Yes
F2ax* ≤ F2axN
F2rad,acc* ≤ F2rad,acc
F2rad,eq* ≤ F2radN
M2k,acc* ≤ M2k,acc
M2k,eq* ≤ M2kN
M1k* ≤ M1k
Yes
Note the information
about explosion-proof
gear units, Document ID
Yes
Check the brake
for safe stop
Check the brake(s) against
the permissible emergency off torque
Yes
Select a larger brake No
or a
higher gear ratio
Select a
larger gear unit
or a
smaller brake
No
2acc 2acc* ZB M
M
fB
£
× h
× ³
L* get 1Bstat M
M 0,8
i
× + × £ × h
1Bstat M,Bmax* 2NOT
get (M 1,4 M ) i
M 0,9
Calculate the forces and tilting torques in the chapter Permitted shaft loads.
Refer to the selection tables for the values for ηget, i, n1maxDB, n1maxZB, M1Bstat, M2acc (M2accHT for reduced backlash), M2NOT and M2N.
9 PHQK right-angle planetary gear units 9.6 Project configuration
255
The values for the available maximum motor brake torque MM,Bmax* can be found in the manufacturer catalog.
The values for fBT, fBop, fBt
and fBZB can be found in the corresponding tables in this chapter.
Example of cyclic operation
The following calculations are based on a representation of the power taken from the output based in accordance with the following example:
Calculation of the actual maximum acceleration torque 2
2acc* tot L* n M J M
9,55 t
D
= × +
9.55 × D
Calculation of the actual average input speed
n1m* n2m* = ×i 2m,1* 1* 2m,n* n* 2m* 1* n* n t ... n t
n
t ... t
× + + × =
+ +
If t1* + ... + t3* ≥ 6 min, calculate n2m* without the rest phase t4*.
The values for the ratio i can be found in the selection tables.
Calculation of the actual emergency-off torque 2
2NOT* tot L* n M J M
9,55 t
D
= × +
9.55 × D
Calculation of the actual equivalent torque 3 3
2m,1* 1* 2,1* 2m,n* n* 2,n* 3
2eq* 2m,1* 1* 2m,n* n* n t M ... n t M
M
n t ... n t
× × + + × × =
× + + ×
Operating factors
Operating mode fBop
Uniform continuous operation 1.00
Cyclic operation 1.25
Reversing load cyclic operation 1.40
Run time fBt
Daily runtime ≤ 8 h 1.00
Daily runtime ≤ 16 h 1.15
Daily runtime ≤ 24 h 1.20
9.6 Project configuration 9 PHQK right-angle planetary gear units
256
Cyclic operation fBZB
≤ 1000 load changes/hour (LW/h) 1.00
> 1000 load changes/hour (LW/h) 1.15
Temperature fBT
Motor cooling Surrounding temperature
Motor with forced ventilation ≤ 20 °C
≤ 30 °C
≤ 40 °C
0.9
1.0
1.15
Motor with convection cooling ≤ 20 °C
≤ 30 °C
≤ 40 °C
1.0
1.1
1.25
Notes
• The maximum permitted gear unit temperature of ≤ 90 °C must not be exceeded. Doing so may result
in damage to the gear unit.
9.6.2 Permitted shaft loads for the output shaft
The values specified in the tables apply to the permitted shaft loads:
• For shaft dimensions in accordance with the catalog
• For output speeds n2m* ≤ 100 rpm (F2axN = F2ax100; F2radN = F2rad100; M2kN = M2k100)
• Only if radial forces on the gear unit are stabilized by its pilots (housing, flange shaft)
Permitted shaft loads for standard bearing S
Type z2 F2ax100 F2rad100 F2rad,acc M2k100 M2k,acc C2k
[mm] [N] [N] [N] [Nm] [Nm] [Nm/
arcmin]
PHQ4 83.0 2150 3095 3929 257 326 192
PHQ5 97.0 4150 4536 4897 440 475 429
PHQ7 86.0 6150 17045 17045 1466 1466 500
PHQ8 125.5 10050 27778 33333 3486 4183 1550
PHQ9 155.0 33000 48387 70968 7500 11000 7500
PHQ10 171.0 50000 51462 73099 8800 12500 9500
PHQ11 231.0 60000 47619 69264 11000 16000 11500
PHQ12 281.0 70000 64057 106761 18000 30000 14000
Permitted shaft loads for reinforced bearing V
Type z2 F2ax100 F2rad100 F2rad,acc M2k100 M2k,acc C2k
[mm] [N] [N] [N] [Nm] [Nm] [Nm/
arcmin]
PHQ4 88.5 2900 4000 4000 354 354 217
PHQ5 104.0 5000 5500 5500 572 572 478
For other output speeds, download diagrams at https://configurator.stoeber.de/en-US/.
The following applies to output speeds n2m* > 100 rpm: 2ax100
2axN
2m* 3
1 F
F
n
100min
- =
rpm 2rad100
2radN
2m* 3
1 F
F
n
100min
- =
rpm 2k100
2kN
2m* 3
1 M
M
n
100min
- =
rpm
The values for F2ax100, F2rad100 and M2k100 can be found in the table \"Permitted shaft loads\" in this chapter.
9 PHQK right-angle planetary gear units 9.6 Project configuration
257
Fig. 2: Force application points
You can determine the permitted radial forces from the permitted tilting torque M2kN and M2k,acc. The actual
radial forces may not exceed the permitted radial forces. The permitted radial forces pertain to the shaft
end (x2 = 0). × × + ×( + ) =
2ax* 2 2rad,acc* 2 2
2k,acc* 2 F y F x z
M
1000
For applications with multiple axial and/or radial forces, you must add the forces as vectors.
In the event of EMERGENCY OFF operation (max. 1000 load changes), you can multiply the permitted forces
and torques for F2ax100, F2rad100 and M2k100 by a factor of two.
Also note the calculation for equivalent values: × × + + × × =
× + + × 3 3
2m,1* 1* 2k,acc,1* 2m,n* n* 2k,acc,n* 3
2k,eq* 2m,1* 1* 2m,n* n* n t M ... n t M
M
n t ... n t
× × + + × × =
× + + × 3 3
2m,1* 1* 2rad,acc,1* 2m,n* n* 2rad,acc,n* 3
2rad,eq* 2m,1* 1* 2m,n* n* n t F ... n t F
F
n t ... n t
The following apply to the bearing service life L10h (ED10 ≤ 40%):
L10h > 10000 h with 1 < M2kN/M2k* < 1.25
L10h > 20000 h with 1.25 < M2kN/M2k* < 1.5
L10h > 30000 h with 1.5 < M2kN/M2k*
For different duty cycles: 10h 10h 10
(ED 40%) 10 40% L L
ED
> =
×
9.6 Project configuration 9 PHQK right-angle planetary gear units
258
9.6.3 Permitted breakdown torques at the gear unit input
For a horizontal mounting position of the motor, verify that the permitted breakdown torque at the gear
unit input is not exceeded before installation on a STOBER gear unit. You can find information for how to do
that in this chapter.
Calculate the actual breakdown torque as follows:
M1k* = F1k* • lsp ≤ M1k
Type M1k
[Nm]
MB23 45
MB33 90
MB43 200
MB53 450
9.6.4 Recommendation for radial shaft seal rings
For a duty cycle > 60% and higher surrounding temperatures, we recommend radial shaft seal rings made of
FKM at the output.
Properties:
• Excellent temperature resistance
• High chemical stability
• Very good resistance to aging
• Excellent resistance in oils and greases
• For use in the food, beverage and pharmaceutical industries
Leak-proofness
Our gear units are equipped with high-quality radial shaft seal rings and checked for leaks. However, a leak
cannot be fully ruled out over the length of use of a gear unit. If you use a gear unit with goods incompatible
with the lubricant, you must take measures to prevent direct contact with the gear unit lubricant in case of a
leak.
9 PHQK right-angle planetary gear units 9.6 Project configuration
259
9.6.5 Reverse operation
To ensure lubrication for circulating gearing parts during cyclic reverse operation from ± 20° to ± 90° at the
output, pay careful attention to the position of the output shaft for the horizontal mounting of the gear
unit, as shown in the diagrams below.
The images show the center position of reverse operation.
Cyclic reverse operation ≤ ± 20° on request.
PHQ4 − PHQ12
1 Position of the mark: bottom
Please note that the hole pattern may be different, depending on the size of the planetary gear unit.
9.7 Additional documentation
Additional documentation related to the product can be found at
http://www.stoeber.de/en/downloads/
Enter the ID of the documentation in the Search term field.
Documentation ID
Operating manual gear units, geared motors PHQ53K – PHQ83K, PHQ94K
– PHQ124K
443357_en
Operating manual for MB23/MB33/MB43/MB53 ServoStop motor
adapters with brake
443287_en
9.7 Additional documentation 9 PHQK right-angle planetary gear units
260
10 K helical bevel gear units
Table of contents
10.1 Overview ........................................................................................................................................................................... 262
10.2 Selection tables ................................................................................................................................................................. 263
10.3 Dimensional drawings ....................................................................................................................................................... 281
10.3.1 A shaft design (hollow shaft), G housing design (pitch circle diameter) .............................................................................. 282
10.3.2 A shaft design (hollow shaft), NG housing design (foot + pitch circle diameter) ................................................................. 284
10.3.3 A shaft design (hollow shaft), GD housing design (pitch circle diameter + torque arm bracket)......................................... 286
10.3.4 A shaft design (hollow shaft), F housing design (round flange) ........................................................................................... 288
10.3.5 A shaft design (hollow shaft), NF housing design (foot + round flange) .............................................................................. 290
10.3.6 S shaft design (hollow shaft with shrink ring), G housing design (pitch circle diameter)..................................................... 292
10.3.7 S shaft design (hollow shaft with shrink ring), NG housing design (foot + pitch circle diameter)........................................ 294
10.3.8 S shaft design (hollow shaft with shrink ring), GD housing design (pitch circle diameter + torque arm bracket) ............... 296
10.3.9 S shaft design (hollow shaft with shrink ring), F housing design (round flange).................................................................. 298
10.3.10 S shaft design (hollow shaft with shrink ring), NF housing design (foot + round flange)..................................................... 300
10.3.11 V shaft design (solid shaft), G housing design (pitch circle diameter).................................................................................. 302
10.3.12 V shaft design (solid shaft), NG housing design (foot + pitch circle diameter) .................................................................... 304
10.3.13 V shaft design (solid shaft), F housing design (round flange)............................................................................................... 306
10.3.14 V shaft design (solid shaft), NF housing design (foot + round flange).................................................................................. 308
10.3.15 Motor adapter design with plug connector and manual release......................................................................................... 310
10.3.16 Oil expansion tank................................................................................................................................................................ 311
10.4 Type designation ............................................................................................................................................................... 312
10.4.1 Nameplate............................................................................................................................................................................ 313
10.5 Product description............................................................................................................................................................ 314
10.5.1 Input options........................................................................................................................................................................ 314
10.5.2 ServoStop motor adapter with brake (MB).......................................................................................................................... 314
10.5.3 Housing design ..................................................................................................................................................................... 317
10.5.4 Combinatorial shaft/housing design .................................................................................................................................... 318
10.5.5 Installation conditions.......................................................................................................................................................... 318
10.5.6 Mounting positions.............................................................................................................................................................. 319
10.5.7 Lubricants............................................................................................................................................................................. 320
10.5.8 Position of the terminal box/plug connector....................................................................................................................... 321
10.5.9 Other product features........................................................................................................................................................ 321
10.5.10 Maintenance ........................................................................................................................................................................ 321
10.5.11 Direction of rotation............................................................................................................................................................. 322
10.6 Project configuration.......................................................................................................................................................... 323
10.6.1 Drive selection...................................................................................................................................................................... 324
10.6.2 Permitted shaft loads for the output shaft .......................................................................................................................... 326
10.6.3 Permitted breakdown torques at the gear unit input.......................................................................................................... 329
10.6.4 Radial shaft seal rings........................................................................................................................................................... 329
10.6.5 Oil expansion tank................................................................................................................................................................ 329
10.7 Additional documentation .................................................................................................................................................. 329
261
10 Helical bevel gear units K
10.1 Overview
Highly rigid, helical-geared right-angle gear units with
integrate brake
Features
Power density ★★☆☆☆
Backlash ★★★☆☆
Price category €€
Shaft load ★★★☆☆
Smooth operation ★★★☆☆
Torsional stiffness ★★☆☆☆
Mass moment of inertia ★★★★☆
Helical gearing ✓
FKM seal ring at the input ✓
Reinforced output bearing (K5 − K8) ✓ (on request)
Safe braking in case of power outage ✓
Safe support of the load with gravity-loaded axes ✓
Easy and reliable attachment to any synchronous servo motor thanks to backlash-free plugin coupling
✓
Key ★☆☆☆☆ good | ★★★★★ excellent
€ Economy | €€€€€ Premium
Technical data
M1Bstat 8 – 160 Nm
i 4 – 99
M2acc 93 – 7700 Nm
Δφ2 1.5 – 12 arcmin
ηget 96 – 97 %
262
10.2 Selection tables
The technical data specified in the selection tables applies to:
• Installation altitudes up to 1000 m above sea level
• Surrounding temperatures from 0 °C to 40 °C
• Without consideration for thermal limiting performance
For all other technical data, refer to https://configurator.stoeber.de/en-US/.
An explanation of the formula symbols can be found in the chapter [} 12.1].
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K102 (M2acc,max = 135 Nm)
4.000 4/1 K102_0040 MB23 8.0 31 8.0 20 12.0 6.0 – 5.1 3300 2800 4000 65 98 220
4.000 4/1 K102_0040 MB23 12 25 8.0 20 12.0 6.0 – 5.1 3300 2800 4000 65 98 220
4.000 4/1 K102_0040 MB23 16 20 8.0 20 12.0 6.0 – 5.1 3300 2800 4000 65 98 220
4.000 4/1 K102_0040 MB23 24 8.4 8.0 20 12.0 6.0 – 5.1 3300 2800 4000 65 98 220
4.000 4/1 K102_0040 MB23 30 – 8.0 20 12.0 6.0 – 5.1 3300 2800 4000 65 98 220
5.568 1520/273 K102_0056 MB23 8.0 26 7.8 20 12.0 6.0 – 5.8 3300 2800 4000 73 109 240
5.568 1520/273 K102_0056 MB23 12 21 7.8 20 12.0 6.0 – 5.8 3300 2800 4000 73 109 240
5.568 1520/273 K102_0056 MB23 16 15 7.8 20 12.0 6.0 – 5.8 3300 2800 4000 73 109 240
5.568 1520/273 K102_0056 MB23 24 4.0 7.8 20 12.0 6.0 – 5.8 3300 2800 4000 73 109 240
6.000 6/1 K102_0060 MB23 8.0 21 7.7 20 12.0 6.0 – 5.9 3300 2800 4000 75 112 220
6.000 6/1 K102_0060 MB23 12 15 7.7 20 12.0 6.0 – 5.9 3300 2800 4000 75 112 220
6.000 6/1 K102_0060 MB23 16 9.6 7.7 20 12.0 6.0 – 5.9 3300 2800 4000 75 112 220
6.644 299/45 K102_0066 MB23 8.0 18 7.6 20 12.0 6.0 – 6.1 3600 3300 4000 77 116 220
6.644 299/45 K102_0066 MB23 12 12 7.6 20 12.0 6.0 – 6.1 3600 3300 4000 77 116 220
6.644 299/45 K102_0066 MB23 16 6.5 7.6 20 12.0 6.0 – 6.1 3600 3300 4000 77 116 220
8.309 1911/230 K102_0083 MB23 8.0 12 7.5 20 12.0 6.0 – 6.3 3600 3300 4000 83 125 220
8.309 1911/230 K102_0083 MB23 12 6.3 7.5 20 12.0 6.0 – 6.3 3600 3300 4000 83 125 220
8.309 1911/230 K102_0083 MB23 16 0.7 7.5 20 12.0 6.0 – 6.3 3600 3300 4000 83 125 220
9.249 1748/189 K102_0092 MB23 8.0 11 7.5 20 12.0 6.0 – 6.4 3600 3300 4000 86 129 240
9.249 1748/189 K102_0092 MB23 12 5.9 7.5 20 12.0 6.0 – 6.4 3600 3300 4000 86 129 240
9.249 1748/189 K102_0092 MB23 16 0.3 7.5 20 12.0 6.0 – 6.4 3600 3300 4000 86 129 240
10.14 507/50 K102_0100 MB23 8.0 7.7 7.4 20 12.0 6.0 – 6.5 4000 3800 4000 89 125 220
10.14 507/50 K102_0100 MB23 12 2.1 7.4 20 12.0 6.0 – 6.5 4000 3800 4000 89 125 220
11.57 266/23 K102_0115 MB23 8.0 6.9 7.4 20 12.0 6.0 – 6.5 3600 3300 4000 93 135 240
11.57 266/23 K102_0115 MB23 12 1.3 7.4 20 12.0 6.0 – 6.5 3600 3300 4000 93 135 240
12.62 429/34 K102_0125 MB23 8.0 4.0 7.3 20 12.0 6.0 – 6.6 4000 3800 4000 96 125 220
14.11 494/35 K102_0140 MB23 8.0 3.6 7.4 20 12.0 6.0 – 6.6 4000 3800 4000 99 135 240
16.71 117/7 K102_0165 MB23 8.0 0.3 7.3 20 12.0 6.0 – 6.7 4000 4000 4000 105 125 220
17.56 2090/119 K102_0175 MB23 8.0 0.7 7.3 20 12.0 6.0 – 6.7 4000 3800 4000 107 135 240
K202 (M2acc,max = 220 Nm)
4.000 4/1 K202_0040 MB23 8.0 31 9.6 27 10.0 5.0 1.5 7.1 3000 2600 4000 116 146 244
4.000 4/1 K202_0040 MB23 12 25 9.6 27 10.0 5.0 1.5 7.1 3000 2600 4000 116 146 244
4.000 4/1 K202_0040 MB23 16 20 9.6 27 10.0 5.0 1.5 7.1 3000 2600 4000 116 146 244
4.000 4/1 K202_0040 MB23 24 8.4 9.6 27 10.0 5.0 1.5 7.1 3000 2600 4000 116 146 244
4.000 4/1 K202_0040 MB23 30 – 9.6 27 10.0 5.0 1.5 7.1 3000 2600 4000 116 146 244
4.000 4/1 K202_0040 MB33 16 65 30 34 10.0 5.0 1.5 8.0 3000 2600 4000 116 174 400
4.000 4/1 K202_0040 MB33 24 54 30 34 10.0 5.0 1.5 8.0 3000 2600 4000 116 174 400
4.000 4/1 K202_0040 MB33 32 43 30 34 10.0 5.0 1.5 8.0 3000 2600 4000 116 174 400
4.000 4/1 K202_0040 MB33 45 24 30 34 10.0 5.0 1.5 8.0 3000 2600 4000 116 174 400
4.364 48/11 K202_0044 MB23 8.0 31 9.3 27 10.0 5.0 1.5 7.5 3000 2600 4000 120 159 267
4.364 48/11 K202_0044 MB23 12 25 9.3 27 10.0 5.0 1.5 7.5 3000 2600 4000 120 159 267
4.364 48/11 K202_0044 MB23 16 20 9.3 27 10.0 5.0 1.5 7.5 3000 2600 4000 120 159 267
4.364 48/11 K202_0044 MB23 24 8.4 9.3 27 10.0 5.0 1.5 7.5 3000 2600 4000 120 159 267
4.364 48/11 K202_0044 MB23 30 – 9.3 27 10.0 5.0 1.5 7.5 3000 2600 4000 120 159 267
4.364 48/11 K202_0044 MB33 16 58 30 34 10.0 5.0 1.5 8.4 3000 2600 4000 120 180 400
4.364 48/11 K202_0044 MB33 24 46 30 34 10.0 5.0 1.5 8.4 3000 2600 4000 120 180 400
4.364 48/11 K202_0044 MB33 32 35 30 34 10.0 5.0 1.5 8.4 3000 2600 4000 120 180 400
4.364 48/11 K202_0044 MB33 45 17 30 34 10.0 5.0 1.5 8.4 3000 2600 4000 120 180 400
5.177 2107/407 K202_0052 MB23 8.0 31 8.8 27 10.0 5.0 1.5 8.2 3000 2600 4000 127 188 316
5.177 2107/407 K202_0052 MB23 12 25 8.8 27 10.0 5.0 1.5 8.2 3000 2600 4000 127 188 316
5.177 2107/407 K202_0052 MB23 16 20 8.8 27 10.0 5.0 1.5 8.2 3000 2600 4000 127 188 316
5.177 2107/407 K202_0052 MB23 24 8.4 8.8 27 10.0 5.0 1.5 8.2 3000 2600 4000 127 188 316
5.177 2107/407 K202_0052 MB23 30 – 8.8 27 10.0 5.0 1.5 8.2 3000 2600 4000 127 188 316
10 K helical bevel gear units 10.2 Selection tables
263
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K202 (M2acc,max = 220 Nm)
5.177 2107/407 K202_0052 MB33 16 45 29 34 10.0 5.0 1.5 8.9 3000 2600 4000 127 190 400
5.177 2107/407 K202_0052 MB33 24 34 29 34 10.0 5.0 1.5 8.9 3000 2600 4000 127 190 400
5.177 2107/407 K202_0052 MB33 32 23 29 34 10.0 5.0 1.5 8.9 3000 2600 4000 127 190 400
5.177 2107/407 K202_0052 MB33 45 4.5 29 34 10.0 5.0 1.5 8.9 3000 2600 4000 127 190 400
6.000 6/1 K202_0060 MB23 8.0 31 8.9 27 10.0 5.0 1.5 8.7 3000 2600 4000 133 200 367
6.000 6/1 K202_0060 MB23 12 25 8.9 27 10.0 5.0 1.5 8.7 3000 2600 4000 133 200 367
6.000 6/1 K202_0060 MB23 16 20 8.9 27 10.0 5.0 1.5 8.7 3000 2600 4000 133 200 367
6.000 6/1 K202_0060 MB23 24 8.4 8.9 27 10.0 5.0 1.5 8.7 3000 2600 4000 133 200 367
6.000 6/1 K202_0060 MB23 30 – 8.9 27 10.0 5.0 1.5 8.7 3000 2600 4000 133 200 367
6.000 6/1 K202_0060 MB33 16 36 29 34 10.0 5.0 1.5 9.3 3000 2600 4000 133 200 400
6.000 6/1 K202_0060 MB33 24 25 29 34 10.0 5.0 1.5 9.3 3000 2600 4000 133 200 400
6.000 6/1 K202_0060 MB33 32 13 29 34 10.0 5.0 1.5 9.3 3000 2600 4000 133 200 400
6.683 2279/341 K202_0067 MB23 8.0 31 8.3 27 10.0 5.0 1.5 9.0 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB23 12 25 8.3 27 10.0 5.0 1.5 9.0 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB23 16 20 8.3 27 10.0 5.0 1.5 9.0 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB23 24 8.4 8.3 27 10.0 5.0 1.5 9.0 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB23 30 – 8.3 27 10.0 5.0 1.5 9.0 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB33 16 30 29 34 10.0 5.0 1.5 9.5 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB33 24 19 29 34 10.0 5.0 1.5 9.5 3500 3100 4000 138 207 400
6.683 2279/341 K202_0067 MB33 32 7.5 29 34 10.0 5.0 1.5 9.5 3500 3100 4000 138 207 400
7.118 2107/296 K202_0071 MB23 8.0 31 8.5 27 10.0 5.0 1.5 9.2 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB23 12 25 8.5 27 10.0 5.0 1.5 9.2 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB23 16 20 8.5 27 10.0 5.0 1.5 9.2 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB23 24 8.4 8.5 27 10.0 5.0 1.5 9.2 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB23 30 – 8.5 27 10.0 5.0 1.5 9.2 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB33 16 27 29 34 10.0 5.0 1.5 9.6 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB33 24 15 29 34 10.0 5.0 1.5 9.6 3000 2600 4000 141 211 400
7.118 2107/296 K202_0071 MB33 32 4.3 29 34 10.0 5.0 1.5 9.6 3000 2600 4000 141 211 400
8.397 2494/297 K202_0084 MB23 8.0 30 7.9 27 10.0 5.0 1.5 9.5 3500 3100 4000 149 220 400
8.397 2494/297 K202_0084 MB23 12 25 7.9 27 10.0 5.0 1.5 9.5 3500 3100 4000 149 220 400
8.397 2494/297 K202_0084 MB23 16 19 7.9 27 10.0 5.0 1.5 9.5 3500 3100 4000 149 220 400
8.397 2494/297 K202_0084 MB23 24 8.0 7.9 27 10.0 5.0 1.5 9.5 3500 3100 4000 149 220 400
8.397 2494/297 K202_0084 MB33 16 19 28 34 10.0 5.0 1.5 9.9 3500 3100 4000 149 220 400
8.397 2494/297 K202_0084 MB33 24 8.0 28 34 10.0 5.0 1.5 9.9 3500 3100 4000 149 220 400
9.190 2279/248 K202_0092 MB23 8.0 27 8.1 27 10.0 5.0 1.5 9.7 3500 3100 4000 153 220 400
9.190 2279/248 K202_0092 MB23 12 21 8.1 27 10.0 5.0 1.5 9.7 3500 3100 4000 153 220 400
9.190 2279/248 K202_0092 MB23 16 16 8.1 27 10.0 5.0 1.5 9.7 3500 3100 4000 153 220 400
9.190 2279/248 K202_0092 MB23 24 4.4 8.1 27 10.0 5.0 1.5 9.7 3500 3100 4000 153 220 400
9.190 2279/248 K202_0092 MB33 16 16 29 34 10.0 5.0 1.5 10 3500 3100 4000 153 220 400
9.190 2279/248 K202_0092 MB33 24 4.4 29 34 10.0 5.0 1.5 10 3500 3100 4000 153 220 400
10.07 2881/286 K202_0100 MB23 8.0 23 7.8 27 10.0 5.0 1.5 9.9 3900 3500 4000 158 220 400
10.07 2881/286 K202_0100 MB23 12 18 7.8 27 10.0 5.0 1.5 9.9 3900 3500 4000 158 220 400
10.07 2881/286 K202_0100 MB23 16 12 7.8 27 10.0 5.0 1.5 9.9 3900 3500 4000 158 220 400
10.07 2881/286 K202_0100 MB23 24 1.1 7.8 27 10.0 5.0 1.5 9.9 3900 3500 4000 158 220 400
10.07 2881/286 K202_0100 MB33 16 12 28 34 10.0 5.0 1.5 10 3900 3500 4000 158 220 400
10.07 2881/286 K202_0100 MB33 24 1.1 28 34 10.0 5.0 1.5 10 3900 3500 4000 158 220 400
11.55 1247/108 K202_0115 MB23 8.0 19 7.8 27 10.0 5.0 1.5 10 3500 3100 4000 166 220 400
11.55 1247/108 K202_0115 MB23 12 13 7.8 27 10.0 5.0 1.5 10 3500 3100 4000 166 220 400
11.55 1247/108 K202_0115 MB23 16 7.8 7.8 27 10.0 5.0 1.5 10 3500 3100 4000 166 220 400
11.55 1247/108 K202_0115 MB33 16 7.8 28 34 10.0 5.0 1.5 10 3500 3100 4000 166 220 400
12.71 559/44 K202_0125 MB23 8.0 16 7.6 27 10.0 5.0 1.5 10 3900 3500 4000 171 220 400
12.71 559/44 K202_0125 MB23 12 11 7.6 27 10.0 5.0 1.5 10 3900 3500 4000 171 220 400
12.71 559/44 K202_0125 MB23 16 5.1 7.6 27 10.0 5.0 1.5 10 3900 3500 4000 171 220 400
12.71 559/44 K202_0125 MB33 16 5.1 28 34 10.0 5.0 1.5 10 3900 3500 4000 171 220 400
13.85 2881/208 K202_0140 MB23 8.0 14 7.7 27 10.0 5.0 1.5 10 3900 3500 4000 176 220 400
13.85 2881/208 K202_0140 MB23 12 8.4 7.7 27 10.0 5.0 1.5 10 3900 3500 4000 176 220 400
13.85 2881/208 K202_0140 MB23 16 2.8 7.7 27 10.0 5.0 1.5 10 3900 3500 4000 176 220 400
13.85 2881/208 K202_0140 MB33 16 2.8 28 34 10.0 5.0 1.5 10 3900 3500 4000 176 220 400
16.86 2967/176 K202_0170 MB23 8.0 9.5 7.4 27 10.0 5.0 1.5 10 4000 3900 4000 188 220 400
16.86 2967/176 K202_0170 MB23 12 3.9 7.4 27 10.0 5.0 1.5 10 4000 3900 4000 188 220 400
17.47 559/32 K202_0175 MB23 8.0 8.8 7.5 27 10.0 5.0 1.5 10 3900 3500 4000 190 220 400
17.47 559/32 K202_0175 MB23 12 3.2 7.5 27 10.0 5.0 1.5 10 3900 3500 4000 190 220 400
20.33 1118/55 K202_0200 MB23 8.0 6.0 7.4 27 10.0 5.0 1.5 10 4000 3900 4000 200 220 400
20.33 1118/55 K202_0200 MB23 12 0.4 7.4 27 10.0 5.0 1.5 10 4000 3900 4000 200 220 400
10.2 Selection tables 10 K helical bevel gear units
264
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K202 (M2acc,max = 220 Nm)
23.18 2967/128 K202_0230 MB23 8.0 3.9 7.4 27 10.0 5.0 1.5 10 4000 3900 4000 200 220 400
25.13 1935/77 K202_0250 MB23 8.0 2.7 7.3 27 10.0 5.0 1.5 11 4000 3900 4000 200 220 400
27.95 559/20 K202_0280 MB23 8.0 1.3 7.4 27 10.0 5.0 1.5 11 4000 3900 4000 200 220 400
K302 (M2acc,max = 385 Nm)
4.000 4/1 K302_0040 MB23 8.0 31 12 32 10.0 4.0 1.5 9.2 2700 2300 4000 146 146 244
4.000 4/1 K302_0040 MB23 12 25 12 32 10.0 4.0 1.5 9.2 2700 2300 4000 146 146 244
4.000 4/1 K302_0040 MB23 16 20 12 32 10.0 4.0 1.5 9.2 2700 2300 4000 146 146 244
4.000 4/1 K302_0040 MB23 24 8.4 12 32 10.0 4.0 1.5 9.2 2700 2300 4000 146 146 244
4.000 4/1 K302_0040 MB23 30 – 12 32 10.0 4.0 1.5 9.2 2700 2300 4000 146 146 244
4.000 4/1 K302_0040 MB33 16 104 34 39 10.0 4.0 1.5 11 2700 2300 4000 204 306 700
4.000 4/1 K302_0040 MB33 24 92 34 39 10.0 4.0 1.5 11 2700 2300 4000 204 306 700
4.000 4/1 K302_0040 MB33 32 81 34 39 10.0 4.0 1.5 11 2700 2300 4000 204 306 700
4.000 4/1 K302_0040 MB33 45 63 34 39 10.0 4.0 1.5 11 2700 2300 4000 204 306 700
4.000 4/1 K302_0040 MB33 90 – 34 39 10.0 4.0 1.5 11 2700 2300 4000 204 306 700
4.364 48/11 K302_0044 MB23 8.0 31 12 32 10.0 4.0 1.5 9.9 2700 2300 4000 159 159 267
4.364 48/11 K302_0044 MB23 12 25 12 32 10.0 4.0 1.5 9.9 2700 2300 4000 159 159 267
4.364 48/11 K302_0044 MB23 16 20 12 32 10.0 4.0 1.5 9.9 2700 2300 4000 159 159 267
4.364 48/11 K302_0044 MB23 24 8.4 12 32 10.0 4.0 1.5 9.9 2700 2300 4000 159 159 267
4.364 48/11 K302_0044 MB23 30 – 12 32 10.0 4.0 1.5 9.9 2700 2300 4000 159 159 267
4.364 48/11 K302_0044 MB33 16 104 33 39 10.0 4.0 1.5 12 2700 2300 4000 210 315 700
4.364 48/11 K302_0044 MB33 24 92 33 39 10.0 4.0 1.5 12 2700 2300 4000 210 315 700
4.364 48/11 K302_0044 MB33 32 81 33 39 10.0 4.0 1.5 12 2700 2300 4000 210 315 700
4.364 48/11 K302_0044 MB33 45 63 33 39 10.0 4.0 1.5 12 2700 2300 4000 210 315 700
4.364 48/11 K302_0044 MB33 90 – 33 39 10.0 4.0 1.5 12 2700 2300 4000 210 315 700
5.375 43/8 K302_0054 MB23 8.0 31 10 32 10.0 4.0 1.5 11 2700 2300 4000 196 196 328
5.375 43/8 K302_0054 MB23 12 25 10 32 10.0 4.0 1.5 11 2700 2300 4000 196 196 328
5.375 43/8 K302_0054 MB23 16 20 10 32 10.0 4.0 1.5 11 2700 2300 4000 196 196 328
5.375 43/8 K302_0054 MB23 24 8.4 10 32 10.0 4.0 1.5 11 2700 2300 4000 196 196 328
5.375 43/8 K302_0054 MB23 30 – 10 32 10.0 4.0 1.5 11 2700 2300 4000 196 196 328
5.375 43/8 K302_0054 MB33 16 76 31 39 10.0 4.0 1.5 13 2700 2300 4000 225 337 603
5.375 43/8 K302_0054 MB33 24 64 31 39 10.0 4.0 1.5 13 2700 2300 4000 225 337 603
5.375 43/8 K302_0054 MB33 32 53 31 39 10.0 4.0 1.5 13 2700 2300 4000 225 337 603
5.375 43/8 K302_0054 MB33 45 35 31 39 10.0 4.0 1.5 13 2700 2300 4000 225 337 603
6.000 6/1 K302_0060 MB23 8.0 31 11 32 10.0 4.0 1.5 12 2700 2300 4000 218 218 367
6.000 6/1 K302_0060 MB23 12 25 11 32 10.0 4.0 1.5 12 2700 2300 4000 218 218 367
6.000 6/1 K302_0060 MB23 16 20 11 32 10.0 4.0 1.5 12 2700 2300 4000 218 218 367
6.000 6/1 K302_0060 MB23 24 8.4 11 32 10.0 4.0 1.5 12 2700 2300 4000 218 218 367
6.000 6/1 K302_0060 MB23 30 – 11 32 10.0 4.0 1.5 12 2700 2300 4000 218 218 367
6.000 6/1 K302_0060 MB33 16 79 32 39 10.0 4.0 1.5 13 2700 2300 4000 233 350 700
6.000 6/1 K302_0060 MB33 24 68 32 39 10.0 4.0 1.5 13 2700 2300 4000 233 350 700
6.000 6/1 K302_0060 MB33 32 57 32 39 10.0 4.0 1.5 13 2700 2300 4000 233 350 700
6.000 6/1 K302_0060 MB33 45 39 32 39 10.0 4.0 1.5 13 2700 2300 4000 233 350 700
6.740 2150/319 K302_0067 MB23 8.0 31 9.4 32 10.0 4.0 1.5 13 3200 2800 4000 242 245 412
6.740 2150/319 K302_0067 MB23 12 25 9.4 32 10.0 4.0 1.5 13 3200 2800 4000 242 245 412
6.740 2150/319 K302_0067 MB23 16 20 9.4 32 10.0 4.0 1.5 13 3200 2800 4000 242 245 412
6.740 2150/319 K302_0067 MB23 24 8.4 9.4 32 10.0 4.0 1.5 13 3200 2800 4000 242 245 412
6.740 2150/319 K302_0067 MB23 30 – 9.4 32 10.0 4.0 1.5 13 3200 2800 4000 242 245 412
6.740 2150/319 K302_0067 MB33 16 68 30 39 10.0 4.0 1.5 14 3200 2800 4000 242 364 700
6.740 2150/319 K302_0067 MB33 24 57 30 39 10.0 4.0 1.5 14 3200 2800 4000 242 364 700
6.740 2150/319 K302_0067 MB33 32 46 30 39 10.0 4.0 1.5 14 3200 2800 4000 242 364 700
6.740 2150/319 K302_0067 MB33 45 28 30 39 10.0 4.0 1.5 14 3200 2800 4000 242 364 700
7.391 473/64 K302_0074 MB23 8.0 31 9.8 32 10.0 4.0 1.5 13 2700 2300 4000 250 269 452
7.391 473/64 K302_0074 MB23 12 25 9.8 32 10.0 4.0 1.5 13 2700 2300 4000 250 269 452
7.391 473/64 K302_0074 MB23 16 20 9.8 32 10.0 4.0 1.5 13 2700 2300 4000 250 269 452
7.391 473/64 K302_0074 MB23 24 8.4 9.8 32 10.0 4.0 1.5 13 2700 2300 4000 250 269 452
7.391 473/64 K302_0074 MB23 30 – 9.8 32 10.0 4.0 1.5 13 2700 2300 4000 250 269 452
7.391 473/64 K302_0074 MB33 16 60 30 39 10.0 4.0 1.5 14 2700 2300 4000 250 375 700
7.391 473/64 K302_0074 MB33 24 49 30 39 10.0 4.0 1.5 14 2700 2300 4000 250 375 700
7.391 473/64 K302_0074 MB33 32 38 30 39 10.0 4.0 1.5 14 2700 2300 4000 250 375 700
7.391 473/64 K302_0074 MB33 45 20 30 39 10.0 4.0 1.5 14 2700 2300 4000 250 375 700
8.444 2322/275 K302_0084 MB23 8.0 31 8.8 32 10.0 4.0 1.5 14 3200 2800 4000 261 307 516
8.444 2322/275 K302_0084 MB23 12 25 8.8 32 10.0 4.0 1.5 14 3200 2800 4000 261 307 516
8.444 2322/275 K302_0084 MB23 16 20 8.8 32 10.0 4.0 1.5 14 3200 2800 4000 261 307 516
8.444 2322/275 K302_0084 MB23 24 8.4 8.8 32 10.0 4.0 1.5 14 3200 2800 4000 261 307 516
10 K helical bevel gear units 10.2 Selection tables
265
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K302 (M2acc,max = 385 Nm)
8.444 2322/275 K302_0084 MB23 30 – 8.8 32 10.0 4.0 1.5 14 3200 2800 4000 261 307 516
8.444 2322/275 K302_0084 MB33 16 50 29 39 10.0 4.0 1.5 15 3200 2800 4000 261 385 700
8.444 2322/275 K302_0084 MB33 24 39 29 39 10.0 4.0 1.5 15 3200 2800 4000 261 385 700
8.444 2322/275 K302_0084 MB33 32 28 29 39 10.0 4.0 1.5 15 3200 2800 4000 261 385 700
8.444 2322/275 K302_0084 MB33 45 9.4 29 39 10.0 4.0 1.5 15 3200 2800 4000 261 385 700
9.267 1075/116 K302_0093 MB23 8.0 31 9.1 32 10.0 4.0 1.5 14 3200 2800 4000 270 337 566
9.267 1075/116 K302_0093 MB23 12 25 9.1 32 10.0 4.0 1.5 14 3200 2800 4000 270 337 566
9.267 1075/116 K302_0093 MB23 16 20 9.1 32 10.0 4.0 1.5 14 3200 2800 4000 270 337 566
9.267 1075/116 K302_0093 MB23 24 8.4 9.1 32 10.0 4.0 1.5 14 3200 2800 4000 270 337 566
9.267 1075/116 K302_0093 MB23 30 – 9.1 32 10.0 4.0 1.5 14 3200 2800 4000 270 337 566
9.267 1075/116 K302_0093 MB33 16 44 30 39 10.0 4.0 1.5 15 3200 2800 4000 270 385 700
9.267 1075/116 K302_0093 MB33 24 32 30 39 10.0 4.0 1.5 15 3200 2800 4000 270 385 700
9.267 1075/116 K302_0093 MB33 32 21 30 39 10.0 4.0 1.5 15 3200 2800 4000 270 385 700
9.267 1075/116 K302_0093 MB33 45 2.9 30 39 10.0 4.0 1.5 15 3200 2800 4000 270 385 700
10.14 3010/297 K302_0100 MB23 8.0 31 8.4 32 10.0 4.0 1.5 15 3500 3100 4000 278 369 619
10.14 3010/297 K302_0100 MB23 12 25 8.4 32 10.0 4.0 1.5 15 3500 3100 4000 278 369 619
10.14 3010/297 K302_0100 MB23 16 20 8.4 32 10.0 4.0 1.5 15 3500 3100 4000 278 369 619
10.14 3010/297 K302_0100 MB23 24 8.4 8.4 32 10.0 4.0 1.5 15 3500 3100 4000 278 369 619
10.14 3010/297 K302_0100 MB23 30 – 8.4 32 10.0 4.0 1.5 15 3500 3100 4000 278 369 619
10.14 3010/297 K302_0100 MB33 16 38 29 39 10.0 4.0 1.5 15 3500 3100 4000 278 385 700
10.14 3010/297 K302_0100 MB33 24 27 29 39 10.0 4.0 1.5 15 3500 3100 4000 278 385 700
10.14 3010/297 K302_0100 MB33 32 15 29 39 10.0 4.0 1.5 15 3500 3100 4000 278 385 700
11.61 1161/100 K302_0115 MB23 8.0 31 8.6 32 10.0 4.0 1.5 15 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB23 12 25 8.6 32 10.0 4.0 1.5 15 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB23 16 20 8.6 32 10.0 4.0 1.5 15 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB23 24 8.4 8.6 32 10.0 4.0 1.5 15 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB23 30 – 8.6 32 10.0 4.0 1.5 15 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB33 16 30 29 39 10.0 4.0 1.5 16 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB33 24 19 29 39 10.0 4.0 1.5 16 3200 2800 4000 291 385 700
11.61 1161/100 K302_0115 MB33 32 7.8 29 39 10.0 4.0 1.5 16 3200 2800 4000 291 385 700
12.58 3182/253 K302_0125 MB23 8.0 31 8.0 32 10.0 4.0 1.5 15 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB23 12 25 8.0 32 10.0 4.0 1.5 15 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB23 16 20 8.0 32 10.0 4.0 1.5 15 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB23 24 8.4 8.0 32 10.0 4.0 1.5 15 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB23 30 – 8.0 32 10.0 4.0 1.5 15 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB33 16 26 29 39 10.0 4.0 1.5 16 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB33 24 15 29 39 10.0 4.0 1.5 16 3500 3100 4000 298 385 700
12.58 3182/253 K302_0125 MB33 32 3.8 29 39 10.0 4.0 1.5 16 3500 3100 4000 298 385 700
13.94 1505/108 K302_0140 MB23 8.0 31 8.2 32 10.0 4.0 1.5 15 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB23 12 25 8.2 32 10.0 4.0 1.5 15 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB23 16 20 8.2 32 10.0 4.0 1.5 15 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB23 24 8.4 8.2 32 10.0 4.0 1.5 15 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB23 30 – 8.2 32 10.0 4.0 1.5 15 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB33 16 21 29 39 10.0 4.0 1.5 16 3500 3100 4000 309 385 700
13.94 1505/108 K302_0140 MB33 24 10 29 39 10.0 4.0 1.5 16 3500 3100 4000 309 385 700
16.94 559/33 K302_0170 MB23 8.0 25 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
16.94 559/33 K302_0170 MB23 12 19 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
16.94 559/33 K302_0170 MB23 16 14 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
16.94 559/33 K302_0170 MB23 24 2.5 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
16.94 559/33 K302_0170 MB33 16 14 28 39 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
16.94 559/33 K302_0170 MB33 24 2.5 28 39 10.0 4.0 1.5 16 3800 3500 4000 330 385 700
17.29 1591/92 K302_0175 MB23 8.0 24 7.9 32 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
17.29 1591/92 K302_0175 MB23 12 19 7.9 32 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
17.29 1591/92 K302_0175 MB23 16 13 7.9 32 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
17.29 1591/92 K302_0175 MB23 24 1.7 7.9 32 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
17.29 1591/92 K302_0175 MB33 16 13 28 39 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
17.29 1591/92 K302_0175 MB33 24 1.7 28 39 10.0 4.0 1.5 16 3500 3100 4000 332 385 700
20.28 3569/176 K302_0200 MB23 8.0 19 7.6 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
20.28 3569/176 K302_0200 MB23 12 13 7.6 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
20.28 3569/176 K302_0200 MB23 16 7.7 7.6 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
20.28 3569/176 K302_0200 MB33 16 7.7 28 39 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
23.29 559/24 K302_0230 MB23 8.0 15 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
23.29 559/24 K302_0230 MB23 12 9.4 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
23.29 559/24 K302_0230 MB23 16 3.8 7.7 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
10.2 Selection tables 10 K helical bevel gear units
266
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K302 (M2acc,max = 385 Nm)
23.29 559/24 K302_0230 MB33 16 3.8 28 39 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
25.26 3612/143 K302_0250 MB23 8.0 13 7.5 32 10.0 4.0 1.5 16 3800 3500 4000 347 385 693
25.26 3612/143 K302_0250 MB23 12 7.2 7.5 32 10.0 4.0 1.5 16 3800 3500 4000 347 385 693
25.26 3612/143 K302_0250 MB23 16 1.6 7.5 32 10.0 4.0 1.5 16 3800 3500 4000 347 385 693
27.88 3569/128 K302_0280 MB23 8.0 11 7.5 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
27.88 3569/128 K302_0280 MB23 12 5.1 7.5 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
33.62 1849/55 K302_0340 MB23 8.0 1.8 7.3 32 10.0 4.0 1.5 16 3800 3500 4000 250 300 501
34.73 903/26 K302_0350 MB23 8.0 6.4 7.4 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
34.73 903/26 K302_0350 MB23 12 0.8 7.4 32 10.0 4.0 1.5 16 3800 3500 4000 350 385 700
46.23 1849/40 K302_0460 MB23 8.0 1.8 7.3 32 10.0 4.0 1.5 16 3800 3500 4000 344 385 688
K402 (M2acc,max = 600 Nm)
4.000 4/1 K402_0040 MB33 16 104 39 53 10.0 4.0 1.5 16 2600 2200 3800 306 388 733
4.000 4/1 K402_0040 MB33 24 92 39 53 10.0 4.0 1.5 16 2600 2200 3800 306 388 733
4.000 4/1 K402_0040 MB33 32 81 39 53 10.0 4.0 1.5 16 2600 2200 3800 306 388 733
4.000 4/1 K402_0040 MB33 45 63 39 53 10.0 4.0 1.5 16 2600 2200 3800 306 388 733
4.000 4/1 K402_0040 MB33 90 – 39 53 10.0 4.0 1.5 16 2600 2200 3800 306 388 733
4.000 4/1 K402_0040 MB43 50 154 86 67 10.0 4.0 1.5 18 2600 2200 3000 306 459 1078
4.000 4/1 K402_0040 MB43 72 123 86 67 10.0 4.0 1.5 18 2600 2200 3000 306 459 1078
4.000 4/1 K402_0040 MB43 100 84 86 67 10.0 4.0 1.5 18 2600 2200 3000 306 459 1078
4.000 4/1 K402_0040 MB43 160 – 86 67 10.0 4.0 1.5 18 2600 2200 3000 306 459 1078
4.364 48/11 K402_0044 MB33 16 104 37 53 10.0 4.0 1.5 17 2600 2200 3800 315 423 800
4.364 48/11 K402_0044 MB33 24 92 37 53 10.0 4.0 1.5 17 2600 2200 3800 315 423 800
4.364 48/11 K402_0044 MB33 32 81 37 53 10.0 4.0 1.5 17 2600 2200 3800 315 423 800
4.364 48/11 K402_0044 MB33 45 63 37 53 10.0 4.0 1.5 17 2600 2200 3800 315 423 800
4.364 48/11 K402_0044 MB33 90 – 37 53 10.0 4.0 1.5 17 2600 2200 3800 315 423 800
4.364 48/11 K402_0044 MB43 50 146 85 67 10.0 4.0 1.5 19 2600 2200 3000 315 472 1078
4.364 48/11 K402_0044 MB43 72 115 85 67 10.0 4.0 1.5 19 2600 2200 3000 315 472 1078
4.364 48/11 K402_0044 MB43 100 76 85 67 10.0 4.0 1.5 19 2600 2200 3000 315 472 1078
5.422 1849/341 K402_0054 MB33 16 104 35 53 10.0 4.0 1.5 20 2600 2200 3800 338 508 994
5.422 1849/341 K402_0054 MB33 24 92 35 53 10.0 4.0 1.5 20 2600 2200 3800 338 508 994
5.422 1849/341 K402_0054 MB33 32 81 35 53 10.0 4.0 1.5 20 2600 2200 3800 338 508 994
5.422 1849/341 K402_0054 MB33 45 63 35 53 10.0 4.0 1.5 20 2600 2200 3800 338 508 994
5.422 1849/341 K402_0054 MB33 90 – 35 53 10.0 4.0 1.5 20 2600 2200 3800 338 508 994
5.422 1849/341 K402_0054 MB43 50 104 83 67 10.0 4.0 1.5 22 2600 2200 3000 338 508 1078
5.422 1849/341 K402_0054 MB43 72 73 83 67 10.0 4.0 1.5 22 2600 2200 3000 338 508 1078
5.422 1849/341 K402_0054 MB43 100 34 83 67 10.0 4.0 1.5 22 2600 2200 3000 338 508 1078
6.000 6/1 K402_0060 MB33 16 104 36 53 10.0 4.0 1.5 22 2600 2200 3800 350 525 1100
6.000 6/1 K402_0060 MB33 24 92 36 53 10.0 4.0 1.5 22 2600 2200 3800 350 525 1100
6.000 6/1 K402_0060 MB33 32 81 36 53 10.0 4.0 1.5 22 2600 2200 3800 350 525 1100
6.000 6/1 K402_0060 MB33 45 63 36 53 10.0 4.0 1.5 22 2600 2200 3800 350 525 1100
6.000 6/1 K402_0060 MB33 90 – 36 53 10.0 4.0 1.5 22 2600 2200 3800 350 525 1100
6.000 6/1 K402_0060 MB43 50 90 83 67 10.0 4.0 1.5 23 2600 2200 3000 350 525 1100
6.000 6/1 K402_0060 MB43 72 59 83 67 10.0 4.0 1.5 23 2600 2200 3000 350 525 1100
6.000 6/1 K402_0060 MB43 100 20 83 67 10.0 4.0 1.5 23 2600 2200 3000 350 525 1100
6.719 215/32 K402_0067 MB23 8.0 31 11 46 10.0 4.0 1.5 20 3000 2600 4000 244 244 411
6.719 215/32 K402_0067 MB23 12 25 11 46 10.0 4.0 1.5 20 3000 2600 4000 244 244 411
6.719 215/32 K402_0067 MB23 16 20 11 46 10.0 4.0 1.5 20 3000 2600 4000 244 244 411
6.719 215/32 K402_0067 MB23 24 8.4 11 46 10.0 4.0 1.5 20 3000 2600 4000 244 244 411
6.719 215/32 K402_0067 MB23 30 – 11 46 10.0 4.0 1.5 20 3000 2600 4000 244 244 411
6.719 215/32 K402_0067 MB33 16 104 33 53 10.0 4.0 1.5 23 3000 2600 4000 363 545 1100
6.719 215/32 K402_0067 MB33 24 92 33 53 10.0 4.0 1.5 23 3000 2600 4000 363 545 1100
6.719 215/32 K402_0067 MB33 32 81 33 53 10.0 4.0 1.5 23 3000 2600 4000 363 545 1100
6.719 215/32 K402_0067 MB33 45 63 33 53 10.0 4.0 1.5 23 3000 2600 4000 363 545 1100
6.719 215/32 K402_0067 MB33 90 – 33 53 10.0 4.0 1.5 23 3000 2600 4000 363 545 1100
6.719 215/32 K402_0067 MB43 50 73 81 67 10.0 4.0 1.5 24 3000 2600 3000 363 545 1100
6.719 215/32 K402_0067 MB43 72 42 81 67 10.0 4.0 1.5 24 3000 2600 3000 363 545 1100
6.719 215/32 K402_0067 MB43 100 2.9 81 67 10.0 4.0 1.5 24 3000 2600 3000 363 545 1100
7.456 1849/248 K402_0075 MB33 16 104 34 53 10.0 4.0 1.5 24 2600 2200 3800 376 564 1100
7.456 1849/248 K402_0075 MB33 24 92 34 53 10.0 4.0 1.5 24 2600 2200 3800 376 564 1100
7.456 1849/248 K402_0075 MB33 32 81 34 53 10.0 4.0 1.5 24 2600 2200 3800 376 564 1100
7.456 1849/248 K402_0075 MB33 45 63 34 53 10.0 4.0 1.5 24 2600 2200 3800 376 564 1100
7.456 1849/248 K402_0075 MB33 90 – 34 53 10.0 4.0 1.5 24 2600 2200 3800 376 564 1100
7.456 1849/248 K402_0075 MB43 50 59 82 67 10.0 4.0 1.5 25 2600 2200 3000 376 564 1100
7.456 1849/248 K402_0075 MB43 72 28 82 67 10.0 4.0 1.5 25 2600 2200 3000 376 564 1100
10 K helical bevel gear units 10.2 Selection tables
267
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K402 (M2acc,max = 600 Nm)
8.377 645/77 K402_0084 MB23 8.0 31 10 46 10.0 4.0 1.5 23 3000 2600 4000 305 305 512
8.377 645/77 K402_0084 MB23 12 25 10 46 10.0 4.0 1.5 23 3000 2600 4000 305 305 512
8.377 645/77 K402_0084 MB23 16 20 10 46 10.0 4.0 1.5 23 3000 2600 4000 305 305 512
8.377 645/77 K402_0084 MB23 24 8.4 10 46 10.0 4.0 1.5 23 3000 2600 4000 305 305 512
8.377 645/77 K402_0084 MB23 30 – 10 46 10.0 4.0 1.5 23 3000 2600 4000 305 305 512
8.377 645/77 K402_0084 MB33 16 92 32 53 10.0 4.0 1.5 25 3000 2600 4000 391 587 1100
8.377 645/77 K402_0084 MB33 24 81 32 53 10.0 4.0 1.5 25 3000 2600 4000 391 587 1100
8.377 645/77 K402_0084 MB33 32 70 32 53 10.0 4.0 1.5 25 3000 2600 4000 391 587 1100
8.377 645/77 K402_0084 MB33 45 52 32 53 10.0 4.0 1.5 25 3000 2600 4000 391 587 1100
8.377 645/77 K402_0084 MB43 50 45 80 67 10.0 4.0 1.5 26 3000 2600 3000 391 587 1100
8.377 645/77 K402_0084 MB43 72 14 80 67 10.0 4.0 1.5 26 3000 2600 3000 391 587 1100
9.238 2365/256 K402_0092 MB23 8.0 31 11 46 10.0 4.0 1.5 24 3000 2600 4000 336 336 565
9.238 2365/256 K402_0092 MB23 12 25 11 46 10.0 4.0 1.5 24 3000 2600 4000 336 336 565
9.238 2365/256 K402_0092 MB23 16 20 11 46 10.0 4.0 1.5 24 3000 2600 4000 336 336 565
9.238 2365/256 K402_0092 MB23 24 8.4 11 46 10.0 4.0 1.5 24 3000 2600 4000 336 336 565
9.238 2365/256 K402_0092 MB23 30 – 11 46 10.0 4.0 1.5 24 3000 2600 4000 336 336 565
9.238 2365/256 K402_0092 MB33 16 82 33 53 10.0 4.0 1.5 26 3000 2600 4000 404 600 1100
9.238 2365/256 K402_0092 MB33 24 70 33 53 10.0 4.0 1.5 26 3000 2600 4000 404 600 1100
9.238 2365/256 K402_0092 MB33 32 59 33 53 10.0 4.0 1.5 26 3000 2600 4000 404 600 1100
9.238 2365/256 K402_0092 MB33 45 41 33 53 10.0 4.0 1.5 26 3000 2600 4000 404 600 1100
9.238 2365/256 K402_0092 MB43 50 34 80 67 10.0 4.0 1.5 27 3000 2600 3000 404 600 1100
9.238 2365/256 K402_0092 MB43 72 3.2 80 67 10.0 4.0 1.5 27 3000 2600 3000 404 600 1100
10.10 1333/132 K402_0100 MB23 8.0 31 9.4 46 10.0 4.0 1.5 25 3400 3000 4000 367 367 617
10.10 1333/132 K402_0100 MB23 12 25 9.4 46 10.0 4.0 1.5 25 3400 3000 4000 367 367 617
10.10 1333/132 K402_0100 MB23 16 20 9.4 46 10.0 4.0 1.5 25 3400 3000 4000 367 367 617
10.10 1333/132 K402_0100 MB23 24 8.4 9.4 46 10.0 4.0 1.5 25 3400 3000 4000 367 367 617
10.10 1333/132 K402_0100 MB23 30 – 9.4 46 10.0 4.0 1.5 25 3400 3000 4000 367 367 617
10.10 1333/132 K402_0100 MB33 16 73 31 53 10.0 4.0 1.5 27 3400 3000 4000 416 600 1100
10.10 1333/132 K402_0100 MB33 24 61 31 53 10.0 4.0 1.5 27 3400 3000 4000 416 600 1100
10.10 1333/132 K402_0100 MB33 32 50 31 53 10.0 4.0 1.5 27 3400 3000 4000 416 600 1100
10.10 1333/132 K402_0100 MB33 45 32 31 53 10.0 4.0 1.5 27 3400 3000 4000 416 600 1100
10.10 1333/132 K402_0100 MB43 50 25 79 67 10.0 4.0 1.5 28 3000 3000 3000 416 600 1100
11.52 645/56 K402_0115 MB23 8.0 31 9.7 46 10.0 4.0 1.5 26 3000 2600 4000 419 419 704
11.52 645/56 K402_0115 MB23 12 25 9.7 46 10.0 4.0 1.5 26 3000 2600 4000 419 419 704
11.52 645/56 K402_0115 MB23 16 20 9.7 46 10.0 4.0 1.5 26 3000 2600 4000 419 419 704
11.52 645/56 K402_0115 MB23 24 8.4 9.7 46 10.0 4.0 1.5 26 3000 2600 4000 419 419 704
11.52 645/56 K402_0115 MB23 30 – 9.7 46 10.0 4.0 1.5 26 3000 2600 4000 419 419 704
11.52 645/56 K402_0115 MB33 16 61 32 53 10.0 4.0 1.5 28 3000 2600 4000 435 600 1100
11.52 645/56 K402_0115 MB33 24 50 32 53 10.0 4.0 1.5 28 3000 2600 4000 435 600 1100
11.52 645/56 K402_0115 MB33 32 39 32 53 10.0 4.0 1.5 28 3000 2600 4000 435 600 1100
11.52 645/56 K402_0115 MB33 45 20 32 53 10.0 4.0 1.5 28 3000 2600 4000 435 600 1100
11.52 645/56 K402_0115 MB43 50 13 79 67 10.0 4.0 1.5 28 3000 2600 3000 435 600 1100
12.66 2924/231 K402_0125 MB23 8.0 31 8.7 46 10.0 4.0 1.5 27 3400 3000 4000 449 460 774
12.66 2924/231 K402_0125 MB23 12 25 8.7 46 10.0 4.0 1.5 27 3400 3000 4000 449 460 774
12.66 2924/231 K402_0125 MB23 16 20 8.7 46 10.0 4.0 1.5 27 3400 3000 4000 449 460 774
12.66 2924/231 K402_0125 MB23 24 8.4 8.7 46 10.0 4.0 1.5 27 3400 3000 4000 449 460 774
12.66 2924/231 K402_0125 MB23 30 – 8.7 46 10.0 4.0 1.5 27 3400 3000 4000 449 460 774
12.66 2924/231 K402_0125 MB33 16 53 31 53 10.0 4.0 1.5 28 3400 3000 4000 449 600 1100
12.66 2924/231 K402_0125 MB33 24 42 31 53 10.0 4.0 1.5 28 3400 3000 4000 449 600 1100
12.66 2924/231 K402_0125 MB33 32 31 31 53 10.0 4.0 1.5 28 3400 3000 4000 449 600 1100
12.66 2924/231 K402_0125 MB33 45 13 31 53 10.0 4.0 1.5 28 3400 3000 4000 449 600 1100
12.66 2924/231 K402_0125 MB43 50 5.9 78 67 10.0 4.0 1.5 29 3000 3000 3000 449 600 1100
13.89 1333/96 K402_0140 MB23 8.0 31 9.1 46 10.0 4.0 1.5 27 3400 3000 4000 463 505 849
13.89 1333/96 K402_0140 MB23 12 25 9.1 46 10.0 4.0 1.5 27 3400 3000 4000 463 505 849
13.89 1333/96 K402_0140 MB23 16 20 9.1 46 10.0 4.0 1.5 27 3400 3000 4000 463 505 849
13.89 1333/96 K402_0140 MB23 24 8.4 9.1 46 10.0 4.0 1.5 27 3400 3000 4000 463 505 849
13.89 1333/96 K402_0140 MB23 30 – 9.1 46 10.0 4.0 1.5 27 3400 3000 4000 463 505 849
13.89 1333/96 K402_0140 MB33 16 47 31 53 10.0 4.0 1.5 29 3400 3000 4000 463 600 1100
13.89 1333/96 K402_0140 MB33 24 36 31 53 10.0 4.0 1.5 29 3400 3000 4000 463 600 1100
13.89 1333/96 K402_0140 MB33 32 24 31 53 10.0 4.0 1.5 29 3400 3000 4000 463 600 1100
13.89 1333/96 K402_0140 MB33 45 6.2 31 53 10.0 4.0 1.5 29 3400 3000 4000 463 600 1100
16.94 559/33 K402_0170 MB23 8.0 31 8.1 46 10.0 4.0 1.5 29 3600 3300 4000 495 600 1035
16.94 559/33 K402_0170 MB23 12 25 8.1 46 10.0 4.0 1.5 29 3600 3300 4000 495 600 1035
16.94 559/33 K402_0170 MB23 16 20 8.1 46 10.0 4.0 1.5 29 3600 3300 4000 495 600 1035
10.2 Selection tables 10 K helical bevel gear units
268
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K402 (M2acc,max = 600 Nm)
16.94 559/33 K402_0170 MB23 24 8.4 8.1 46 10.0 4.0 1.5 29 3600 3300 4000 495 600 1035
16.94 559/33 K402_0170 MB23 30 – 8.1 46 10.0 4.0 1.5 29 3600 3300 4000 495 600 1035
16.94 559/33 K402_0170 MB33 16 34 30 53 10.0 4.0 1.5 29 3600 3300 4000 495 600 1100
16.94 559/33 K402_0170 MB33 24 23 30 53 10.0 4.0 1.5 29 3600 3300 4000 495 600 1100
16.94 559/33 K402_0170 MB33 32 12 30 53 10.0 4.0 1.5 29 3600 3300 4000 495 600 1100
17.41 731/42 K402_0175 MB23 8.0 31 8.6 46 10.0 4.0 1.5 29 3400 3000 4000 499 600 1064
17.41 731/42 K402_0175 MB23 12 25 8.6 46 10.0 4.0 1.5 29 3400 3000 4000 499 600 1064
17.41 731/42 K402_0175 MB23 16 20 8.6 46 10.0 4.0 1.5 29 3400 3000 4000 499 600 1064
17.41 731/42 K402_0175 MB23 24 8.4 8.6 46 10.0 4.0 1.5 29 3400 3000 4000 499 600 1064
17.41 731/42 K402_0175 MB23 30 – 8.6 46 10.0 4.0 1.5 29 3400 3000 4000 499 600 1064
17.41 731/42 K402_0175 MB33 16 33 30 53 10.0 4.0 1.5 29 3400 3000 4000 499 600 1100
17.41 731/42 K402_0175 MB33 24 22 30 53 10.0 4.0 1.5 29 3400 3000 4000 499 600 1100
17.41 731/42 K402_0175 MB33 32 10 30 53 10.0 4.0 1.5 29 3400 3000 4000 499 600 1100
20.20 1333/66 K402_0200 MB23 8.0 31 7.9 46 10.0 4.0 1.5 29 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB23 12 25 7.9 46 10.0 4.0 1.5 29 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB23 16 20 7.9 46 10.0 4.0 1.5 29 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB23 24 8.4 7.9 46 10.0 4.0 1.5 29 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB23 30 – 7.9 46 10.0 4.0 1.5 29 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB33 16 25 28 53 10.0 4.0 1.5 30 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB33 24 14 28 53 10.0 4.0 1.5 30 3600 3300 4000 524 600 1100
20.20 1333/66 K402_0200 MB33 32 2.7 28 53 10.0 4.0 1.5 30 3600 3300 4000 524 600 1100
23.29 559/24 K402_0230 MB23 8.0 30 8.0 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
23.29 559/24 K402_0230 MB23 12 24 8.0 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
23.29 559/24 K402_0230 MB23 16 19 8.0 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
23.29 559/24 K402_0230 MB23 24 7.6 8.0 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
23.29 559/24 K402_0230 MB33 16 19 30 53 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
23.29 559/24 K402_0230 MB33 24 7.6 30 53 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
25.28 4171/165 K402_0250 MB23 8.0 23 7.7 46 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
25.28 4171/165 K402_0250 MB23 12 18 7.7 46 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
25.28 4171/165 K402_0250 MB23 16 12 7.7 46 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
25.28 4171/165 K402_0250 MB23 24 1.0 7.7 46 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
25.28 4171/165 K402_0250 MB33 16 12 28 53 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
25.28 4171/165 K402_0250 MB33 24 1.0 28 53 10.0 4.0 1.5 30 3600 3300 4000 501 600 1001
27.77 1333/48 K402_0280 MB23 8.0 23 7.8 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
27.77 1333/48 K402_0280 MB23 12 18 7.8 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
27.77 1333/48 K402_0280 MB23 16 12 7.8 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
27.77 1333/48 K402_0280 MB23 24 1.0 7.8 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
27.77 1333/48 K402_0280 MB33 16 12 28 53 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
27.77 1333/48 K402_0280 MB33 24 1.0 28 53 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
33.68 4816/143 K402_0340 MB23 8.0 9.0 7.5 46 10.0 4.0 1.5 30 3600 3300 4000 389 467 778
33.68 4816/143 K402_0340 MB23 12 3.4 7.5 46 10.0 4.0 1.5 30 3600 3300 4000 389 467 778
34.76 4171/120 K402_0350 MB23 8.0 16 7.6 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
34.76 4171/120 K402_0350 MB23 12 11 7.6 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
34.76 4171/120 K402_0350 MB23 16 5.2 7.6 46 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
34.76 4171/120 K402_0350 MB33 16 5.2 28 53 10.0 4.0 1.5 30 3600 3300 4000 550 600 1100
40.51 4902/121 K402_0410 MB23 8.0 2.1 7.4 46 10.0 4.0 1.5 30 3600 3300 4000 308 370 616
46.31 602/13 K402_0460 MB23 8.0 9.0 7.5 46 10.0 4.0 1.5 31 3600 3300 4000 535 600 1069
46.31 602/13 K402_0460 MB23 12 3.4 7.5 46 10.0 4.0 1.5 31 3600 3300 4000 535 600 1069
55.71 2451/44 K402_0560 MB23 8.0 2.1 7.4 46 10.0 4.0 1.5 31 3600 3300 4000 424 508 847
K513 (M2acc,max = 1000 Nm)
7.347 551/75 K513_0073 MB33 16 104 45 59 10.0 5.0 2.0 34 1900 1800 3200 694 702 1327
7.347 551/75 K513_0073 MB33 24 92 45 59 10.0 5.0 2.0 34 1900 1800 3200 694 702 1327
7.347 551/75 K513_0073 MB33 32 81 45 59 10.0 5.0 2.0 34 1900 1800 3200 694 702 1327
7.347 551/75 K513_0073 MB33 45 63 45 59 10.0 5.0 2.0 34 1900 1800 3200 694 702 1327
7.347 551/75 K513_0073 MB33 90 – 45 59 10.0 5.0 2.0 34 1900 1800 3200 694 702 1327
7.347 551/75 K513_0073 MB43 50 141 92 72 10.0 5.0 2.0 37 1900 1800 3000 694 1000 1800
7.347 551/75 K513_0073 MB43 72 110 92 72 10.0 5.0 2.0 37 1900 1800 3000 694 1000 1800
7.347 551/75 K513_0073 MB43 100 71 92 72 10.0 5.0 2.0 37 1900 1800 3000 694 1000 1800
8.134 17081/2100 K513_0081 MB33 16 104 43 59 10.0 5.0 2.0 36 1900 1800 3200 718 778 1470
8.134 17081/2100 K513_0081 MB33 24 92 43 59 10.0 5.0 2.0 36 1900 1800 3200 718 778 1470
8.134 17081/2100 K513_0081 MB33 32 81 43 59 10.0 5.0 2.0 36 1900 1800 3200 718 778 1470
8.134 17081/2100 K513_0081 MB33 45 63 43 59 10.0 5.0 2.0 36 1900 1800 3200 718 778 1470
8.134 17081/2100 K513_0081 MB33 90 – 43 59 10.0 5.0 2.0 36 1900 1800 3200 718 778 1470
8.134 17081/2100 K513_0081 MB43 50 120 91 72 10.0 5.0 2.0 39 1900 1800 3000 718 1000 1800
10 K helical bevel gear units 10.2 Selection tables
269
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K513 (M2acc,max = 1000 Nm)
8.134 17081/2100 K513_0081 MB43 72 90 91 72 10.0 5.0 2.0 39 1900 1800 3000 718 1000 1800
8.134 17081/2100 K513_0081 MB43 100 50 91 72 10.0 5.0 2.0 39 1900 1800 3000 718 1000 1800
9.168 1421/155 K513_0092 MB33 16 104 40 59 10.0 5.0 2.0 38 1900 1800 3200 748 876 1657
9.168 1421/155 K513_0092 MB33 24 92 40 59 10.0 5.0 2.0 38 1900 1800 3200 748 876 1657
9.168 1421/155 K513_0092 MB33 32 81 40 59 10.0 5.0 2.0 38 1900 1800 3200 748 876 1657
9.168 1421/155 K513_0092 MB33 45 63 40 59 10.0 5.0 2.0 38 1900 1800 3200 748 876 1657
9.168 1421/155 K513_0092 MB33 90 – 40 59 10.0 5.0 2.0 38 1900 1800 3200 748 876 1657
9.168 1421/155 K513_0092 MB43 50 99 88 72 10.0 5.0 2.0 40 1900 1800 3000 748 1000 1800
9.168 1421/155 K513_0092 MB43 72 68 88 72 10.0 5.0 2.0 40 1900 1800 3000 748 1000 1800
9.168 1421/155 K513_0092 MB43 100 29 88 72 10.0 5.0 2.0 40 1900 1800 3000 748 1000 1800
10.15 203/20 K513_0100 MB33 16 104 39 59 10.0 5.0 2.0 40 1900 1800 3200 773 970 1800
10.15 203/20 K513_0100 MB33 24 92 39 59 10.0 5.0 2.0 40 1900 1800 3200 773 970 1800
10.15 203/20 K513_0100 MB33 32 81 39 59 10.0 5.0 2.0 40 1900 1800 3200 773 970 1800
10.15 203/20 K513_0100 MB33 45 63 39 59 10.0 5.0 2.0 40 1900 1800 3200 773 970 1800
10.15 203/20 K513_0100 MB33 90 – 39 59 10.0 5.0 2.0 40 1900 1800 3200 773 970 1800
10.15 203/20 K513_0100 MB43 50 83 87 72 10.0 5.0 2.0 42 1900 1800 3000 773 1000 1800
10.15 203/20 K513_0100 MB43 72 52 87 72 10.0 5.0 2.0 42 1900 1800 3000 773 1000 1800
10.15 203/20 K513_0100 MB43 100 13 87 72 10.0 5.0 2.0 42 1900 1800 3000 773 1000 1800
11.57 10759/930 K513_0115 MB33 16 104 37 59 10.0 5.0 2.0 42 2300 2200 3600 808 1000 1800
11.57 10759/930 K513_0115 MB33 24 92 37 59 10.0 5.0 2.0 42 2300 2200 3600 808 1000 1800
11.57 10759/930 K513_0115 MB33 32 81 37 59 10.0 5.0 2.0 42 2300 2200 3600 808 1000 1800
11.57 10759/930 K513_0115 MB33 45 63 37 59 10.0 5.0 2.0 42 2300 2200 3600 808 1000 1800
11.57 10759/930 K513_0115 MB33 90 – 37 59 10.0 5.0 2.0 42 2300 2200 3600 808 1000 1800
11.57 10759/930 K513_0115 MB43 50 64 85 72 10.0 5.0 2.0 43 2300 2200 3000 808 1000 1800
11.57 10759/930 K513_0115 MB43 72 33 85 72 10.0 5.0 2.0 43 2300 2200 3000 808 1000 1800
12.81 1537/120 K513_0130 MB33 16 99 36 59 10.0 5.0 2.0 43 2300 2200 3600 836 1000 1800
12.81 1537/120 K513_0130 MB33 24 87 36 59 10.0 5.0 2.0 43 2300 2200 3600 836 1000 1800
12.81 1537/120 K513_0130 MB33 32 76 36 59 10.0 5.0 2.0 43 2300 2200 3600 836 1000 1800
12.81 1537/120 K513_0130 MB33 45 58 36 59 10.0 5.0 2.0 43 2300 2200 3600 836 1000 1800
12.81 1537/120 K513_0130 MB43 50 51 84 72 10.0 5.0 2.0 44 2300 2200 3000 836 1000 1800
12.81 1537/120 K513_0130 MB43 72 20 84 72 10.0 5.0 2.0 44 2300 2200 3000 836 1000 1800
14.54 5887/405 K513_0145 MB23 8.0 31 13 52 10.0 5.0 2.0 42 2300 2200 3600 521 521 875
14.54 5887/405 K513_0145 MB23 12 25 13 52 10.0 5.0 2.0 42 2300 2200 3600 521 521 875
14.54 5887/405 K513_0145 MB23 16 20 13 52 10.0 5.0 2.0 42 2300 2200 3600 521 521 875
14.54 5887/405 K513_0145 MB23 24 8.4 13 52 10.0 5.0 2.0 42 2300 2200 3600 521 521 875
14.54 5887/405 K513_0145 MB23 30 – 13 52 10.0 5.0 2.0 42 2300 2200 3600 521 521 875
14.54 5887/405 K513_0145 MB33 16 84 35 59 10.0 5.0 2.0 44 2300 2200 3600 872 1000 1800
14.54 5887/405 K513_0145 MB33 24 73 35 59 10.0 5.0 2.0 44 2300 2200 3600 872 1000 1800
14.54 5887/405 K513_0145 MB33 32 62 35 59 10.0 5.0 2.0 44 2300 2200 3600 872 1000 1800
14.54 5887/405 K513_0145 MB33 45 44 35 59 10.0 5.0 2.0 44 2300 2200 3600 872 1000 1800
14.54 5887/405 K513_0145 MB43 50 37 82 72 10.0 5.0 2.0 45 2300 2200 3000 872 1000 1800
14.54 5887/405 K513_0145 MB43 72 5.7 82 72 10.0 5.0 2.0 45 2300 2200 3000 872 1000 1800
16.09 26071/1620 K513_0160 MB23 8.0 31 12 52 10.0 5.0 2.0 43 2300 2200 3600 577 577 969
16.09 26071/1620 K513_0160 MB23 12 25 12 52 10.0 5.0 2.0 43 2300 2200 3600 577 577 969
16.09 26071/1620 K513_0160 MB23 16 20 12 52 10.0 5.0 2.0 43 2300 2200 3600 577 577 969
16.09 26071/1620 K513_0160 MB23 24 8.4 12 52 10.0 5.0 2.0 43 2300 2200 3600 577 577 969
16.09 26071/1620 K513_0160 MB23 30 – 12 52 10.0 5.0 2.0 43 2300 2200 3600 577 577 969
16.09 26071/1620 K513_0160 MB33 16 74 34 59 10.0 5.0 2.0 45 2300 2200 3600 900 1000 1800
16.09 26071/1620 K513_0160 MB33 24 63 34 59 10.0 5.0 2.0 45 2300 2200 3600 900 1000 1800
16.09 26071/1620 K513_0160 MB33 32 51 34 59 10.0 5.0 2.0 45 2300 2200 3600 900 1000 1800
16.09 26071/1620 K513_0160 MB33 45 33 34 59 10.0 5.0 2.0 45 2300 2200 3600 900 1000 1800
16.09 26071/1620 K513_0160 MB43 50 26 82 72 10.0 5.0 2.0 46 2300 2200 3000 900 1000 1800
17.48 6293/360 K513_0175 MB23 8.0 31 12 52 10.0 5.0 2.0 44 2800 2500 4000 627 627 1053
17.48 6293/360 K513_0175 MB23 12 25 12 52 10.0 5.0 2.0 44 2800 2500 4000 627 627 1053
17.48 6293/360 K513_0175 MB23 16 20 12 52 10.0 5.0 2.0 44 2800 2500 4000 627 627 1053
17.48 6293/360 K513_0175 MB23 24 8.4 12 52 10.0 5.0 2.0 44 2800 2500 4000 627 627 1053
17.48 6293/360 K513_0175 MB23 30 – 12 52 10.0 5.0 2.0 44 2800 2500 4000 627 627 1053
17.48 6293/360 K513_0175 MB33 16 66 33 59 10.0 5.0 2.0 46 2800 2500 4000 900 1000 1800
17.48 6293/360 K513_0175 MB33 24 55 33 59 10.0 5.0 2.0 46 2800 2500 4000 900 1000 1800
17.48 6293/360 K513_0175 MB33 32 44 33 59 10.0 5.0 2.0 46 2800 2500 4000 900 1000 1800
17.48 6293/360 K513_0175 MB33 45 26 33 59 10.0 5.0 2.0 46 2800 2500 4000 900 1000 1800
17.48 6293/360 K513_0175 MB43 50 19 81 72 10.0 5.0 2.0 47 2800 2500 3000 900 1000 1800
19.35 27869/1440 K513_0195 MB23 8.0 31 11 52 10.0 5.0 2.0 45 2800 2500 4000 694 694 1166
19.35 27869/1440 K513_0195 MB23 12 25 11 52 10.0 5.0 2.0 45 2800 2500 4000 694 694 1166
10.2 Selection tables 10 K helical bevel gear units
270
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K513 (M2acc,max = 1000 Nm)
19.35 27869/1440 K513_0195 MB23 16 20 11 52 10.0 5.0 2.0 45 2800 2500 4000 694 694 1166
19.35 27869/1440 K513_0195 MB23 24 8.4 11 52 10.0 5.0 2.0 45 2800 2500 4000 694 694 1166
19.35 27869/1440 K513_0195 MB23 30 – 11 52 10.0 5.0 2.0 45 2800 2500 4000 694 694 1166
19.35 27869/1440 K513_0195 MB33 16 58 33 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
19.35 27869/1440 K513_0195 MB33 24 46 33 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
19.35 27869/1440 K513_0195 MB33 32 35 33 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
19.35 27869/1440 K513_0195 MB33 45 17 33 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
19.35 27869/1440 K513_0195 MB43 50 10 81 72 10.0 5.0 2.0 47 2800 2500 3000 900 1000 1800
21.99 2639/120 K513_0220 MB23 8.0 31 10 52 10.0 5.0 2.0 46 2800 2500 4000 788 788 1325
21.99 2639/120 K513_0220 MB23 12 25 10 52 10.0 5.0 2.0 46 2800 2500 4000 788 788 1325
21.99 2639/120 K513_0220 MB23 16 20 10 52 10.0 5.0 2.0 46 2800 2500 4000 788 788 1325
21.99 2639/120 K513_0220 MB23 24 8.4 10 52 10.0 5.0 2.0 46 2800 2500 4000 788 788 1325
21.99 2639/120 K513_0220 MB23 30 – 10 52 10.0 5.0 2.0 46 2800 2500 4000 788 788 1325
21.99 2639/120 K513_0220 MB33 16 48 32 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
21.99 2639/120 K513_0220 MB33 24 37 32 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
21.99 2639/120 K513_0220 MB33 32 26 32 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
21.99 2639/120 K513_0220 MB33 45 7.4 32 59 10.0 5.0 2.0 47 2800 2500 4000 900 1000 1800
21.99 2639/120 K513_0220 MB43 50 0.4 80 72 10.0 5.0 2.0 48 2800 2500 3000 900 1000 1800
24.35 11687/480 K513_0240 MB23 8.0 31 10 52 10.0 5.0 2.0 47 2800 2500 4000 873 873 1466
24.35 11687/480 K513_0240 MB23 12 25 10 52 10.0 5.0 2.0 47 2800 2500 4000 873 873 1466
24.35 11687/480 K513_0240 MB23 16 20 10 52 10.0 5.0 2.0 47 2800 2500 4000 873 873 1466
24.35 11687/480 K513_0240 MB23 24 8.4 10 52 10.0 5.0 2.0 47 2800 2500 4000 873 873 1466
24.35 11687/480 K513_0240 MB23 30 – 10 52 10.0 5.0 2.0 47 2800 2500 4000 873 873 1466
24.35 11687/480 K513_0240 MB33 16 41 32 59 10.0 5.0 2.0 48 2800 2500 4000 900 1000 1800
24.35 11687/480 K513_0240 MB33 24 30 32 59 10.0 5.0 2.0 48 2800 2500 4000 900 1000 1800
24.35 11687/480 K513_0240 MB33 32 19 32 59 10.0 5.0 2.0 48 2800 2500 4000 900 1000 1800
24.35 11687/480 K513_0240 MB33 45 0.6 32 59 10.0 5.0 2.0 48 2800 2500 4000 900 1000 1800
29.18 4669/160 K513_0290 MB23 8.0 31 9.2 52 10.0 5.0 2.0 47 3400 3000 4000 900 1000 1758
29.18 4669/160 K513_0290 MB23 12 25 9.2 52 10.0 5.0 2.0 47 3400 3000 4000 900 1000 1758
29.18 4669/160 K513_0290 MB23 16 20 9.2 52 10.0 5.0 2.0 47 3400 3000 4000 900 1000 1758
29.18 4669/160 K513_0290 MB23 24 8.4 9.2 52 10.0 5.0 2.0 47 3400 3000 4000 900 1000 1758
29.18 4669/160 K513_0290 MB23 30 – 9.2 52 10.0 5.0 2.0 47 3400 3000 4000 900 1000 1758
29.18 4669/160 K513_0290 MB33 16 31 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
29.18 4669/160 K513_0290 MB33 24 19 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
29.18 4669/160 K513_0290 MB33 32 8.3 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB23 8.0 31 9.1 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB23 12 25 9.1 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB23 16 20 9.1 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB23 24 8.4 9.1 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB23 30 – 9.1 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB33 16 26 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB33 24 14 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
32.31 20677/640 K513_0320 MB33 32 3.1 31 59 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB23 8.0 31 8.7 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB23 12 25 8.7 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB23 16 20 8.7 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB23 24 8.4 8.7 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB23 30 – 8.7 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB33 16 22 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
34.80 174/5 K513_0350 MB33 24 11 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB23 8.0 29 8.6 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB23 12 23 8.6 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB23 16 18 8.6 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB23 24 6.6 8.6 52 10.0 5.0 2.0 48 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB33 16 18 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
38.53 2697/70 K513_0390 MB33 24 6.6 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB23 8.0 24 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB23 12 19 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB23 16 13 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB23 24 2.0 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB33 16 13 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
43.50 87/2 K513_0440 MB33 24 2.0 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
48.16 2697/56 K513_0480 MB23 8.0 21 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
48.16 2697/56 K513_0480 MB23 12 15 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
10 K helical bevel gear units 10.2 Selection tables
271
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K513 (M2acc,max = 1000 Nm)
48.16 2697/56 K513_0480 MB23 16 9.8 8.2 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
48.16 2697/56 K513_0480 MB33 16 9.8 29 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
58.30 11368/195 K513_0580 MB23 8.0 15 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
58.30 11368/195 K513_0580 MB23 12 9.8 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
58.30 11368/195 K513_0580 MB23 16 4.2 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
58.30 11368/195 K513_0580 MB33 16 4.2 28 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
64.54 12586/195 K513_0650 MB23 8.0 13 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
64.54 12586/195 K513_0650 MB23 12 7.2 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
64.54 12586/195 K513_0650 MB23 16 1.6 7.8 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
64.54 12586/195 K513_0650 MB33 16 1.6 28 59 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
70.08 841/12 K513_0700 MB23 8.0 9.0 7.6 52 10.0 5.0 2.0 49 3400 3000 4000 821 985 1641
70.08 841/12 K513_0700 MB23 12 3.4 7.6 52 10.0 5.0 2.0 49 3400 3000 4000 821 985 1641
77.59 26071/336 K513_0780 MB23 8.0 8.8 7.6 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
77.59 26071/336 K513_0780 MB23 12 3.2 7.6 52 10.0 5.0 2.0 49 3400 3000 4000 900 1000 1800
87.29 8729/100 K513_0870 MB23 8.0 2.4 7.5 52 10.0 5.0 2.0 49 3400 3000 4000 689 827 1379
96.64 38657/400 K513_0970 MB23 8.0 2.4 7.5 52 10.0 5.0 2.0 49 3400 3000 4000 763 916 1526
K613 (M2acc,max = 1600 Nm)
7.323 19215/2624 K613_0073 MB33 16 104 58 80 10.0 5.0 2.0 47 1800 1700 3000 700 700 1323
7.323 19215/2624 K613_0073 MB33 24 92 58 80 10.0 5.0 2.0 47 1800 1700 3000 700 700 1323
7.323 19215/2624 K613_0073 MB33 32 81 58 80 10.0 5.0 2.0 47 1800 1700 3000 700 700 1323
7.323 19215/2624 K613_0073 MB33 45 63 58 80 10.0 5.0 2.0 47 1800 1700 3000 700 700 1323
7.323 19215/2624 K613_0073 MB33 90 – 58 80 10.0 5.0 2.0 47 1800 1700 3000 700 700 1323
7.323 19215/2624 K613_0073 MB43 50 154 111 94 10.0 5.0 2.0 52 1800 1700 3000 916 1375 2352
7.323 19215/2624 K613_0073 MB43 72 123 111 94 10.0 5.0 2.0 52 1800 1700 3000 916 1375 2352
7.323 19215/2624 K613_0073 MB43 100 84 111 94 10.0 5.0 2.0 52 1800 1700 3000 916 1375 2352
7.323 19215/2624 K613_0073 MB43 160 – 111 94 10.0 5.0 2.0 52 1800 1700 3000 916 1375 2352
8.107 85095/10496 K613_0081 MB33 16 104 56 80 10.0 5.0 2.0 51 1800 1700 3000 775 775 1465
8.107 85095/10496 K613_0081 MB33 24 92 56 80 10.0 5.0 2.0 51 1800 1700 3000 775 775 1465
8.107 85095/10496 K613_0081 MB33 32 81 56 80 10.0 5.0 2.0 51 1800 1700 3000 775 775 1465
8.107 85095/10496 K613_0081 MB33 45 63 56 80 10.0 5.0 2.0 51 1800 1700 3000 775 775 1465
8.107 85095/10496 K613_0081 MB33 90 – 56 80 10.0 5.0 2.0 51 1800 1700 3000 775 775 1465
8.107 85095/10496 K613_0081 MB43 50 154 109 94 10.0 5.0 2.0 56 1800 1700 3000 948 1422 2604
8.107 85095/10496 K613_0081 MB43 72 123 109 94 10.0 5.0 2.0 56 1800 1700 3000 948 1422 2604
8.107 85095/10496 K613_0081 MB43 100 84 109 94 10.0 5.0 2.0 56 1800 1700 3000 948 1422 2604
8.107 85095/10496 K613_0081 MB43 160 – 109 94 10.0 5.0 2.0 56 1800 1700 3000 948 1422 2604
11.41 22631/1984 K613_0115 MB33 16 104 44 80 10.0 5.0 2.0 63 2200 2000 3500 1062 1091 2061
11.41 22631/1984 K613_0115 MB33 24 92 44 80 10.0 5.0 2.0 63 2200 2000 3500 1062 1091 2061
11.41 22631/1984 K613_0115 MB33 32 81 44 80 10.0 5.0 2.0 63 2200 2000 3500 1062 1091 2061
11.41 22631/1984 K613_0115 MB33 45 63 44 80 10.0 5.0 2.0 63 2200 2000 3500 1062 1091 2061
11.41 22631/1984 K613_0115 MB33 90 – 44 80 10.0 5.0 2.0 63 2200 2000 3500 1062 1091 2061
11.41 22631/1984 K613_0115 MB43 50 149 92 94 10.0 5.0 2.0 66 2200 2000 3000 1062 1594 2900
11.41 22631/1984 K613_0115 MB43 72 118 92 94 10.0 5.0 2.0 66 2200 2000 3000 1062 1594 2900
11.41 22631/1984 K613_0115 MB43 100 79 92 94 10.0 5.0 2.0 66 2200 2000 3000 1062 1594 2900
12.63 3233/256 K613_0125 MB33 16 104 43 80 10.0 5.0 2.0 66 2200 2000 3500 1099 1207 2282
12.63 3233/256 K613_0125 MB33 24 92 43 80 10.0 5.0 2.0 66 2200 2000 3500 1099 1207 2282
12.63 3233/256 K613_0125 MB33 32 81 43 80 10.0 5.0 2.0 66 2200 2000 3500 1099 1207 2282
12.63 3233/256 K613_0125 MB33 45 63 43 80 10.0 5.0 2.0 66 2200 2000 3500 1099 1207 2282
12.63 3233/256 K613_0125 MB33 90 – 43 80 10.0 5.0 2.0 66 2200 2000 3500 1099 1207 2282
12.63 3233/256 K613_0125 MB43 50 128 91 94 10.0 5.0 2.0 69 2200 2000 3000 1099 1600 2900
12.63 3233/256 K613_0125 MB43 72 97 91 94 10.0 5.0 2.0 69 2200 2000 3000 1099 1600 2900
12.63 3233/256 K613_0125 MB43 100 58 91 94 10.0 5.0 2.0 69 2200 2000 3000 1099 1600 2900
14.33 12383/864 K613_0145 MB33 16 104 40 80 10.0 5.0 2.0 69 2200 2000 3500 1146 1370 2590
14.33 12383/864 K613_0145 MB33 24 92 40 80 10.0 5.0 2.0 69 2200 2000 3500 1146 1370 2590
14.33 12383/864 K613_0145 MB33 32 81 40 80 10.0 5.0 2.0 69 2200 2000 3500 1146 1370 2590
14.33 12383/864 K613_0145 MB33 45 63 40 80 10.0 5.0 2.0 69 2200 2000 3500 1146 1370 2590
14.33 12383/864 K613_0145 MB33 90 – 40 80 10.0 5.0 2.0 69 2200 2000 3500 1146 1370 2590
14.33 12383/864 K613_0145 MB43 50 104 87 94 10.0 5.0 2.0 72 2200 2000 3000 1146 1600 2900
14.33 12383/864 K613_0145 MB43 72 73 87 94 10.0 5.0 2.0 72 2200 2000 3000 1146 1600 2900
14.33 12383/864 K613_0145 MB43 100 34 87 94 10.0 5.0 2.0 72 2200 2000 3000 1146 1600 2900
15.87 54839/3456 K613_0160 MB33 16 104 39 80 10.0 5.0 2.0 71 2200 2000 3500 1186 1517 2867
15.87 54839/3456 K613_0160 MB33 24 92 39 80 10.0 5.0 2.0 71 2200 2000 3500 1186 1517 2867
15.87 54839/3456 K613_0160 MB33 32 81 39 80 10.0 5.0 2.0 71 2200 2000 3500 1186 1517 2867
15.87 54839/3456 K613_0160 MB33 45 63 39 80 10.0 5.0 2.0 71 2200 2000 3500 1186 1517 2867
15.87 54839/3456 K613_0160 MB33 90 – 39 80 10.0 5.0 2.0 71 2200 2000 3500 1186 1517 2867
10.2 Selection tables 10 K helical bevel gear units
272
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K613 (M2acc,max = 1600 Nm)
15.87 54839/3456 K613_0160 MB43 50 87 87 94 10.0 5.0 2.0 73 2200 2000 3000 1186 1600 2900
15.87 54839/3456 K613_0160 MB43 72 56 87 94 10.0 5.0 2.0 73 2200 2000 3000 1186 1600 2900
15.87 54839/3456 K613_0160 MB43 100 17 87 94 10.0 5.0 2.0 73 2200 2000 3000 1186 1600 2900
17.16 549/32 K613_0170 MB23 8.0 31 15 73 10.0 5.0 2.0 68 2600 2300 4000 615 615 1033
17.16 549/32 K613_0170 MB23 12 25 15 73 10.0 5.0 2.0 68 2600 2300 4000 615 615 1033
17.16 549/32 K613_0170 MB23 16 20 15 73 10.0 5.0 2.0 68 2600 2300 4000 615 615 1033
17.16 549/32 K613_0170 MB23 24 8.4 15 73 10.0 5.0 2.0 68 2600 2300 4000 615 615 1033
17.16 549/32 K613_0170 MB23 30 – 15 73 10.0 5.0 2.0 68 2600 2300 4000 615 615 1033
17.16 549/32 K613_0170 MB33 16 104 37 80 10.0 5.0 2.0 73 2600 2300 4000 1217 1600 2900
17.16 549/32 K613_0170 MB33 24 92 37 80 10.0 5.0 2.0 73 2600 2300 4000 1217 1600 2900
17.16 549/32 K613_0170 MB33 32 81 37 80 10.0 5.0 2.0 73 2600 2300 4000 1217 1600 2900
17.16 549/32 K613_0170 MB33 45 63 37 80 10.0 5.0 2.0 73 2600 2300 4000 1217 1600 2900
17.16 549/32 K613_0170 MB33 90 – 37 80 10.0 5.0 2.0 73 2600 2300 4000 1217 1600 2900
17.16 549/32 K613_0170 MB43 50 75 85 94 10.0 5.0 2.0 75 2600 2300 3000 1217 1600 2900
17.16 549/32 K613_0170 MB43 72 45 85 94 10.0 5.0 2.0 75 2600 2300 3000 1217 1600 2900
17.16 549/32 K613_0170 MB43 100 5.4 85 94 10.0 5.0 2.0 75 2600 2300 3000 1217 1600 2900
18.99 17019/896 K613_0190 MB23 8.0 31 15 73 10.0 5.0 2.0 70 2600 2300 4000 681 681 1144
18.99 17019/896 K613_0190 MB23 12 25 15 73 10.0 5.0 2.0 70 2600 2300 4000 681 681 1144
18.99 17019/896 K613_0190 MB23 16 20 15 73 10.0 5.0 2.0 70 2600 2300 4000 681 681 1144
18.99 17019/896 K613_0190 MB23 24 8.4 15 73 10.0 5.0 2.0 70 2600 2300 4000 681 681 1144
18.99 17019/896 K613_0190 MB23 30 – 15 73 10.0 5.0 2.0 70 2600 2300 4000 681 681 1144
18.99 17019/896 K613_0190 MB33 16 104 37 80 10.0 5.0 2.0 74 2600 2300 4000 1259 1600 2900
18.99 17019/896 K613_0190 MB33 24 92 37 80 10.0 5.0 2.0 74 2600 2300 4000 1259 1600 2900
18.99 17019/896 K613_0190 MB33 32 81 37 80 10.0 5.0 2.0 74 2600 2300 4000 1259 1600 2900
18.99 17019/896 K613_0190 MB33 45 63 37 80 10.0 5.0 2.0 74 2600 2300 4000 1259 1600 2900
18.99 17019/896 K613_0190 MB33 90 – 37 80 10.0 5.0 2.0 74 2600 2300 4000 1259 1600 2900
18.99 17019/896 K613_0190 MB43 50 61 84 94 10.0 5.0 2.0 76 2600 2300 3000 1259 1600 2900
18.99 17019/896 K613_0190 MB43 72 31 84 94 10.0 5.0 2.0 76 2600 2300 3000 1259 1600 2900
21.68 5551/256 K613_0220 MB33 16 93 35 80 10.0 5.0 2.0 76 2600 2300 4000 1316 1600 2900
21.68 5551/256 K613_0220 MB33 24 81 35 80 10.0 5.0 2.0 76 2600 2300 4000 1316 1600 2900
21.68 5551/256 K613_0220 MB33 32 70 35 80 10.0 5.0 2.0 76 2600 2300 4000 1316 1600 2900
21.68 5551/256 K613_0220 MB33 45 52 35 80 10.0 5.0 2.0 76 2600 2300 4000 1316 1600 2900
21.68 5551/256 K613_0220 MB43 50 45 82 94 10.0 5.0 2.0 77 2600 2300 3000 1316 1600 2900
21.68 5551/256 K613_0220 MB43 72 14 82 94 10.0 5.0 2.0 77 2600 2300 3000 1316 1600 2900
24.01 24583/1024 K613_0240 MB33 16 82 34 80 10.0 5.0 2.0 77 2600 2300 4000 1361 1600 2900
24.01 24583/1024 K613_0240 MB33 24 70 34 80 10.0 5.0 2.0 77 2600 2300 4000 1361 1600 2900
24.01 24583/1024 K613_0240 MB33 32 59 34 80 10.0 5.0 2.0 77 2600 2300 4000 1361 1600 2900
24.01 24583/1024 K613_0240 MB33 45 41 34 80 10.0 5.0 2.0 77 2600 2300 4000 1361 1600 2900
24.01 24583/1024 K613_0240 MB43 50 34 82 94 10.0 5.0 2.0 78 2600 2300 3000 1361 1600 2900
24.01 24583/1024 K613_0240 MB43 72 3.1 82 94 10.0 5.0 2.0 78 2600 2300 3000 1361 1600 2900
28.77 29463/1024 K613_0290 MB23 8.0 31 11 73 10.0 5.0 2.0 77 3100 2800 4000 1031 1031 1733
28.77 29463/1024 K613_0290 MB23 12 25 11 73 10.0 5.0 2.0 77 3100 2800 4000 1031 1031 1733
28.77 29463/1024 K613_0290 MB23 16 20 11 73 10.0 5.0 2.0 77 3100 2800 4000 1031 1031 1733
28.77 29463/1024 K613_0290 MB23 24 8.4 11 73 10.0 5.0 2.0 77 3100 2800 4000 1031 1031 1733
28.77 29463/1024 K613_0290 MB23 30 – 11 73 10.0 5.0 2.0 77 3100 2800 4000 1031 1031 1733
28.77 29463/1024 K613_0290 MB33 16 64 33 80 10.0 5.0 2.0 79 3100 2800 4000 1446 1600 2900
28.77 29463/1024 K613_0290 MB33 24 53 33 80 10.0 5.0 2.0 79 3100 2800 4000 1446 1600 2900
28.77 29463/1024 K613_0290 MB33 32 42 33 80 10.0 5.0 2.0 79 3100 2800 4000 1446 1600 2900
28.77 29463/1024 K613_0290 MB33 45 24 33 80 10.0 5.0 2.0 79 3100 2800 4000 1446 1600 2900
28.77 29463/1024 K613_0290 MB43 50 17 80 94 10.0 5.0 2.0 79 3000 2800 3000 1446 1600 2900
31.86 130479/4096 K613_0320 MB23 8.0 31 11 73 10.0 5.0 2.0 78 3100 2800 4000 1142 1142 1919
31.86 130479/4096 K613_0320 MB23 12 25 11 73 10.0 5.0 2.0 78 3100 2800 4000 1142 1142 1919
31.86 130479/4096 K613_0320 MB23 16 20 11 73 10.0 5.0 2.0 78 3100 2800 4000 1142 1142 1919
31.86 130479/4096 K613_0320 MB23 24 8.4 11 73 10.0 5.0 2.0 78 3100 2800 4000 1142 1142 1919
31.86 130479/4096 K613_0320 MB23 30 – 11 73 10.0 5.0 2.0 78 3100 2800 4000 1142 1142 1919
31.86 130479/4096 K613_0320 MB33 16 56 33 80 10.0 5.0 2.0 79 3100 2800 4000 1450 1600 2900
31.86 130479/4096 K613_0320 MB33 24 45 33 80 10.0 5.0 2.0 79 3100 2800 4000 1450 1600 2900
31.86 130479/4096 K613_0320 MB33 32 34 33 80 10.0 5.0 2.0 79 3100 2800 4000 1450 1600 2900
31.86 130479/4096 K613_0320 MB33 45 15 33 80 10.0 5.0 2.0 79 3100 2800 4000 1450 1600 2900
31.86 130479/4096 K613_0320 MB43 50 8.3 80 94 10.0 5.0 2.0 80 3000 2800 3000 1450 1600 2900
34.61 35441/1024 K613_0350 MB23 8.0 31 9.9 73 10.0 5.0 2.0 78 3100 2800 4000 1241 1241 2084
34.61 35441/1024 K613_0350 MB23 12 25 9.9 73 10.0 5.0 2.0 78 3100 2800 4000 1241 1241 2084
34.61 35441/1024 K613_0350 MB23 16 20 9.9 73 10.0 5.0 2.0 78 3100 2800 4000 1241 1241 2084
34.61 35441/1024 K613_0350 MB23 24 8.4 9.9 73 10.0 5.0 2.0 78 3100 2800 4000 1241 1241 2084
10 K helical bevel gear units 10.2 Selection tables
273
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K613 (M2acc,max = 1600 Nm)
34.61 35441/1024 K613_0350 MB23 30 – 9.9 73 10.0 5.0 2.0 78 3100 2800 4000 1241 1241 2084
34.61 35441/1024 K613_0350 MB33 16 50 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
34.61 35441/1024 K613_0350 MB33 24 38 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
34.61 35441/1024 K613_0350 MB33 32 27 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
34.61 35441/1024 K613_0350 MB33 45 9.1 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
34.61 35441/1024 K613_0350 MB43 50 2.1 79 94 10.0 5.0 2.0 80 3000 2800 3000 1450 1600 2900
38.32 156953/4096 K613_0380 MB23 8.0 31 9.8 73 10.0 5.0 2.0 79 3100 2800 4000 1374 1374 2308
38.32 156953/4096 K613_0380 MB23 12 25 9.8 73 10.0 5.0 2.0 79 3100 2800 4000 1374 1374 2308
38.32 156953/4096 K613_0380 MB23 16 20 9.8 73 10.0 5.0 2.0 79 3100 2800 4000 1374 1374 2308
38.32 156953/4096 K613_0380 MB23 24 8.4 9.8 73 10.0 5.0 2.0 79 3100 2800 4000 1374 1374 2308
38.32 156953/4096 K613_0380 MB23 30 – 9.8 73 10.0 5.0 2.0 79 3100 2800 4000 1374 1374 2308
38.32 156953/4096 K613_0380 MB33 16 43 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
38.32 156953/4096 K613_0380 MB33 24 32 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
38.32 156953/4096 K613_0380 MB33 32 20 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
38.32 156953/4096 K613_0380 MB33 45 2.1 32 80 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2900
43.11 8967/208 K613_0430 MB23 8.0 31 9.1 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1546 2596
43.11 8967/208 K613_0430 MB23 12 25 9.1 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1546 2596
43.11 8967/208 K613_0430 MB23 16 20 9.1 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1546 2596
43.11 8967/208 K613_0430 MB23 24 8.4 9.1 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1546 2596
43.11 8967/208 K613_0430 MB23 30 – 9.1 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1546 2596
43.11 8967/208 K613_0430 MB33 16 35 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
43.11 8967/208 K613_0430 MB33 24 24 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
43.11 8967/208 K613_0430 MB33 32 13 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
47.73 39711/832 K613_0480 MB23 8.0 31 9.0 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2875
47.73 39711/832 K613_0480 MB23 12 25 9.0 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2875
47.73 39711/832 K613_0480 MB23 16 20 9.0 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2875
47.73 39711/832 K613_0480 MB23 24 8.4 9.0 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2875
47.73 39711/832 K613_0480 MB23 30 – 9.0 73 10.0 5.0 2.0 80 3100 2800 4000 1450 1600 2875
47.73 39711/832 K613_0480 MB33 16 30 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
47.73 39711/832 K613_0480 MB33 24 19 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
47.73 39711/832 K613_0480 MB33 32 7.5 30 80 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB23 8.0 31 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB23 12 25 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB23 16 20 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB23 24 8.4 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB23 30 – 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB33 16 21 29 80 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
57.55 29463/512 K613_0580 MB33 24 9.8 29 80 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB23 8.0 28 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB23 12 22 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB23 16 17 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB23 24 5.6 8.3 73 10.0 5.0 2.0 81 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB33 16 17 29 80 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
63.71 130479/2048 K613_0640 MB33 24 5.6 29 80 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
68.77 28609/416 K613_0690 MB23 8.0 22 8.0 73 10.0 5.0 2.0 81 3100 2800 4000 1314 1577 2628
68.77 28609/416 K613_0690 MB23 12 16 8.0 73 10.0 5.0 2.0 81 3100 2800 4000 1314 1577 2628
68.77 28609/416 K613_0690 MB23 16 10 8.0 73 10.0 5.0 2.0 81 3100 2800 4000 1314 1577 2628
68.77 28609/416 K613_0690 MB33 16 10 29 80 10.0 5.0 2.0 82 3100 2800 4000 1314 1577 2628
76.14 126697/1664 K613_0760 MB23 8.0 22 8.0 73 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
76.14 126697/1664 K613_0760 MB23 12 16 8.0 73 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
76.14 126697/1664 K613_0760 MB23 16 10 8.0 73 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
76.14 126697/1664 K613_0760 MB33 16 10 29 80 10.0 5.0 2.0 82 3100 2800 4000 1450 1600 2900
86.18 66185/768 K613_0860 MB23 8.0 8.2 7.7 73 10.0 5.0 2.0 82 3100 2800 4000 971 1165 1942
86.18 66185/768 K613_0860 MB23 12 2.6 7.7 73 10.0 5.0 2.0 82 3100 2800 4000 971 1165 1942
95.41 293105/3072 K613_0950 MB23 8.0 8.2 7.7 73 10.0 5.0 2.0 82 3100 2800 4000 1075 1290 2150
95.41 293105/3072 K613_0950 MB23 12 2.6 7.7 73 10.0 5.0 2.0 82 3100 2800 4000 1075 1290 2150
K713 (M2acc,max = 2600 Nm)
7.563 19845/2624 K713_0076 MB43 50 154 141 122 10.0 5.0 2.0 68 1700 1600 2700 1464 1620 2429
7.563 19845/2624 K713_0076 MB43 72 123 141 122 10.0 5.0 2.0 68 1700 1600 2700 1464 1620 2429
7.563 19845/2624 K713_0076 MB43 100 84 141 122 10.0 5.0 2.0 68 1700 1600 2700 1464 1620 2429
7.563 19845/2624 K713_0076 MB43 160 – 141 122 10.0 5.0 2.0 68 1700 1600 2700 1464 1620 2429
8.373 87885/10496 K713_0084 MB43 50 154 137 122 10.0 5.0 2.0 75 1700 1600 2700 1568 1793 2690
8.373 87885/10496 K713_0084 MB43 72 123 137 122 10.0 5.0 2.0 75 1700 1600 2700 1568 1793 2690
8.373 87885/10496 K713_0084 MB43 100 84 137 122 10.0 5.0 2.0 75 1700 1600 2700 1568 1793 2690
10.2 Selection tables 10 K helical bevel gear units
274
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K713 (M2acc,max = 2600 Nm)
8.373 87885/10496 K713_0084 MB43 160 – 137 122 10.0 5.0 2.0 75 1700 1600 2700 1568 1793 2690
9.188 147/16 K713_0092 MB43 50 154 126 122 10.0 5.0 2.0 80 1700 1600 2700 1618 1968 2951
9.188 147/16 K713_0092 MB43 72 123 126 122 10.0 5.0 2.0 80 1700 1600 2700 1618 1968 2951
9.188 147/16 K713_0092 MB43 100 84 126 122 10.0 5.0 2.0 80 1700 1600 2700 1618 1968 2951
9.188 147/16 K713_0092 MB43 160 – 126 122 10.0 5.0 2.0 80 1700 1600 2700 1618 1968 2951
10.17 651/64 K713_0100 MB43 50 154 123 122 10.0 5.0 2.0 86 1700 1600 2700 1674 2178 3267
10.17 651/64 K713_0100 MB43 72 123 123 122 10.0 5.0 2.0 86 1700 1600 2700 1674 2178 3267
10.17 651/64 K713_0100 MB43 100 84 123 122 10.0 5.0 2.0 86 1700 1600 2700 1674 2178 3267
10.17 651/64 K713_0100 MB43 160 – 123 122 10.0 5.0 2.0 86 1700 1600 2700 1674 2178 3267
11.78 23373/1984 K713_0120 MB33 16 104 60 108 10.0 5.0 2.0 87 2000 1900 3200 1126 1126 2129
11.78 23373/1984 K713_0120 MB33 24 92 60 108 10.0 5.0 2.0 87 2000 1900 3200 1126 1126 2129
11.78 23373/1984 K713_0120 MB33 32 81 60 108 10.0 5.0 2.0 87 2000 1900 3200 1126 1126 2129
11.78 23373/1984 K713_0120 MB33 45 63 60 108 10.0 5.0 2.0 87 2000 1900 3200 1126 1126 2129
11.78 23373/1984 K713_0120 MB33 90 – 60 108 10.0 5.0 2.0 87 2000 1900 3200 1126 1126 2129
11.78 23373/1984 K713_0120 MB43 50 154 113 122 10.0 5.0 2.0 93 2000 1900 3000 1758 2523 3784
11.78 23373/1984 K713_0120 MB43 72 123 113 122 10.0 5.0 2.0 93 2000 1900 3000 1758 2523 3784
11.78 23373/1984 K713_0120 MB43 100 84 113 122 10.0 5.0 2.0 93 2000 1900 3000 1758 2523 3784
11.78 23373/1984 K713_0120 MB43 160 – 113 122 10.0 5.0 2.0 93 2000 1900 3000 1758 2523 3784
13.04 3339/256 K713_0130 MB33 16 104 58 108 10.0 5.0 2.0 92 2000 1900 3200 1247 1247 2357
13.04 3339/256 K713_0130 MB33 24 92 58 108 10.0 5.0 2.0 92 2000 1900 3200 1247 1247 2357
13.04 3339/256 K713_0130 MB33 32 81 58 108 10.0 5.0 2.0 92 2000 1900 3200 1247 1247 2357
13.04 3339/256 K713_0130 MB33 45 63 58 108 10.0 5.0 2.0 92 2000 1900 3200 1247 1247 2357
13.04 3339/256 K713_0130 MB33 90 – 58 108 10.0 5.0 2.0 92 2000 1900 3200 1247 1247 2357
13.04 3339/256 K713_0130 MB43 50 154 111 122 10.0 5.0 2.0 98 2000 1900 3000 1818 2600 4190
13.04 3339/256 K713_0130 MB43 72 123 111 122 10.0 5.0 2.0 98 2000 1900 3000 1818 2600 4190
13.04 3339/256 K713_0130 MB43 100 84 111 122 10.0 5.0 2.0 98 2000 1900 3000 1818 2600 4190
13.04 3339/256 K713_0130 MB43 160 – 111 122 10.0 5.0 2.0 98 2000 1900 3000 1818 2600 4190
14.80 1421/96 K713_0150 MB33 16 104 51 108 10.0 5.0 2.0 98 2000 1900 3200 1415 1415 2674
14.80 1421/96 K713_0150 MB33 24 92 51 108 10.0 5.0 2.0 98 2000 1900 3200 1415 1415 2674
14.80 1421/96 K713_0150 MB33 32 81 51 108 10.0 5.0 2.0 98 2000 1900 3200 1415 1415 2674
14.80 1421/96 K713_0150 MB33 45 63 51 108 10.0 5.0 2.0 98 2000 1900 3200 1415 1415 2674
14.80 1421/96 K713_0150 MB33 90 – 51 108 10.0 5.0 2.0 98 2000 1900 3200 1415 1415 2674
14.80 1421/96 K713_0150 MB43 50 154 104 122 10.0 5.0 2.0 103 2000 1900 3000 1896 2600 4755
14.80 1421/96 K713_0150 MB43 72 123 104 122 10.0 5.0 2.0 103 2000 1900 3000 1896 2600 4755
14.80 1421/96 K713_0150 MB43 100 84 104 122 10.0 5.0 2.0 103 2000 1900 3000 1896 2600 4755
14.80 1421/96 K713_0150 MB43 160 – 104 122 10.0 5.0 2.0 103 2000 1900 3000 1896 2600 4755
16.39 6293/384 K713_0165 MB33 16 104 50 108 10.0 5.0 2.0 102 2000 1900 3200 1567 1567 2961
16.39 6293/384 K713_0165 MB33 24 92 50 108 10.0 5.0 2.0 102 2000 1900 3200 1567 1567 2961
16.39 6293/384 K713_0165 MB33 32 81 50 108 10.0 5.0 2.0 102 2000 1900 3200 1567 1567 2961
16.39 6293/384 K713_0165 MB33 45 63 50 108 10.0 5.0 2.0 102 2000 1900 3200 1567 1567 2961
16.39 6293/384 K713_0165 MB33 90 – 50 108 10.0 5.0 2.0 102 2000 1900 3200 1567 1567 2961
16.39 6293/384 K713_0165 MB43 50 154 103 122 10.0 5.0 2.0 107 2000 1900 3000 1962 2600 4800
16.39 6293/384 K713_0165 MB43 72 123 103 122 10.0 5.0 2.0 107 2000 1900 3000 1962 2600 4800
16.39 6293/384 K713_0165 MB43 100 84 103 122 10.0 5.0 2.0 107 2000 1900 3000 1962 2600 4800
16.39 6293/384 K713_0165 MB43 160 – 103 122 10.0 5.0 2.0 107 2000 1900 3000 1962 2600 4800
18.28 26901/1472 K713_0185 MB33 16 104 46 108 10.0 5.0 2.0 106 2400 2200 3600 1747 1747 3302
18.28 26901/1472 K713_0185 MB33 24 92 46 108 10.0 5.0 2.0 106 2400 2200 3600 1747 1747 3302
18.28 26901/1472 K713_0185 MB33 32 81 46 108 10.0 5.0 2.0 106 2400 2200 3600 1747 1747 3302
18.28 26901/1472 K713_0185 MB33 45 63 46 108 10.0 5.0 2.0 106 2400 2200 3600 1747 1747 3302
18.28 26901/1472 K713_0185 MB33 90 – 46 108 10.0 5.0 2.0 106 2400 2200 3600 1747 1747 3302
18.28 26901/1472 K713_0185 MB43 50 154 99 122 10.0 5.0 2.0 110 2400 2200 3000 2034 2600 4800
18.28 26901/1472 K713_0185 MB43 72 123 99 122 10.0 5.0 2.0 110 2400 2200 3000 2034 2600 4800
18.28 26901/1472 K713_0185 MB43 100 84 99 122 10.0 5.0 2.0 110 2400 2200 3000 2034 2600 4800
18.28 26901/1472 K713_0185 MB43 160 – 99 122 10.0 5.0 2.0 110 2400 2200 3000 2034 2600 4800
20.23 119133/5888 K713_0200 MB33 16 104 45 108 10.0 5.0 2.0 109 2400 2200 3600 1934 1934 3656
20.23 119133/5888 K713_0200 MB33 24 92 45 108 10.0 5.0 2.0 109 2400 2200 3600 1934 1934 3656
20.23 119133/5888 K713_0200 MB33 32 81 45 108 10.0 5.0 2.0 109 2400 2200 3600 1934 1934 3656
20.23 119133/5888 K713_0200 MB33 45 63 45 108 10.0 5.0 2.0 109 2400 2200 3600 1934 1934 3656
20.23 119133/5888 K713_0200 MB33 90 – 45 108 10.0 5.0 2.0 109 2400 2200 3600 1934 1934 3656
20.23 119133/5888 K713_0200 MB43 50 134 98 122 10.0 5.0 2.0 112 2400 2200 3000 2105 2600 4800
20.23 119133/5888 K713_0200 MB43 72 103 98 122 10.0 5.0 2.0 112 2400 2200 3000 2105 2600 4800
20.23 119133/5888 K713_0200 MB43 100 64 98 122 10.0 5.0 2.0 112 2400 2200 3000 2105 2600 4800
22.74 14553/640 K713_0230 MB33 16 104 41 108 10.0 5.0 2.0 112 2400 2200 3600 2174 2174 4109
22.74 14553/640 K713_0230 MB33 24 92 41 108 10.0 5.0 2.0 112 2400 2200 3600 2174 2174 4109
10 K helical bevel gear units 10.2 Selection tables
275
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K713 (M2acc,max = 2600 Nm)
22.74 14553/640 K713_0230 MB33 32 81 41 108 10.0 5.0 2.0 112 2400 2200 3600 2174 2174 4109
22.74 14553/640 K713_0230 MB33 45 63 41 108 10.0 5.0 2.0 112 2400 2200 3600 2174 2174 4109
22.74 14553/640 K713_0230 MB33 90 – 41 108 10.0 5.0 2.0 112 2400 2200 3600 2174 2174 4109
22.74 14553/640 K713_0230 MB43 50 112 94 122 10.0 5.0 2.0 115 2400 2200 3000 2188 2600 4800
22.74 14553/640 K713_0230 MB43 72 81 94 122 10.0 5.0 2.0 115 2400 2200 3000 2188 2600 4800
22.74 14553/640 K713_0230 MB43 100 42 94 122 10.0 5.0 2.0 115 2400 2200 3000 2188 2600 4800
25.18 64449/2560 K713_0250 MB33 16 104 41 108 10.0 5.0 2.0 114 2400 2200 3600 2264 2407 4549
25.18 64449/2560 K713_0250 MB33 24 92 41 108 10.0 5.0 2.0 114 2400 2200 3600 2264 2407 4549
25.18 64449/2560 K713_0250 MB33 32 81 41 108 10.0 5.0 2.0 114 2400 2200 3600 2264 2407 4549
25.18 64449/2560 K713_0250 MB33 45 63 41 108 10.0 5.0 2.0 114 2400 2200 3600 2264 2407 4549
25.18 64449/2560 K713_0250 MB33 90 – 41 108 10.0 5.0 2.0 114 2400 2200 3600 2264 2407 4549
25.18 64449/2560 K713_0250 MB43 50 94 94 122 10.0 5.0 2.0 117 2400 2200 3000 2264 2600 4800
25.18 64449/2560 K713_0250 MB43 72 63 94 122 10.0 5.0 2.0 117 2400 2200 3000 2264 2600 4800
25.18 64449/2560 K713_0250 MB43 100 24 94 122 10.0 5.0 2.0 117 2400 2200 3000 2264 2600 4800
29.29 7497/256 K713_0290 MB33 16 104 37 108 10.0 5.0 2.0 117 2900 2600 4000 2381 2600 4800
29.29 7497/256 K713_0290 MB33 24 92 37 108 10.0 5.0 2.0 117 2900 2600 4000 2381 2600 4800
29.29 7497/256 K713_0290 MB33 32 81 37 108 10.0 5.0 2.0 117 2900 2600 4000 2381 2600 4800
29.29 7497/256 K713_0290 MB33 45 63 37 108 10.0 5.0 2.0 117 2900 2600 4000 2381 2600 4800
29.29 7497/256 K713_0290 MB33 90 – 37 108 10.0 5.0 2.0 117 2900 2600 4000 2381 2600 4800
29.29 7497/256 K713_0290 MB43 50 71 90 122 10.0 5.0 2.0 119 2900 2600 3000 2381 2600 4800
29.29 7497/256 K713_0290 MB43 72 40 90 122 10.0 5.0 2.0 119 2900 2600 3000 2381 2600 4800
29.29 7497/256 K713_0290 MB43 100 1.0 90 122 10.0 5.0 2.0 119 2900 2600 3000 2381 2600 4800
32.42 33201/1024 K713_0320 MB33 16 104 37 108 10.0 5.0 2.0 119 2900 2600 4000 2400 2600 4800
32.42 33201/1024 K713_0320 MB33 24 92 37 108 10.0 5.0 2.0 119 2900 2600 4000 2400 2600 4800
32.42 33201/1024 K713_0320 MB33 32 81 37 108 10.0 5.0 2.0 119 2900 2600 4000 2400 2600 4800
32.42 33201/1024 K713_0320 MB33 45 63 37 108 10.0 5.0 2.0 119 2900 2600 4000 2400 2600 4800
32.42 33201/1024 K713_0320 MB33 90 – 37 108 10.0 5.0 2.0 119 2900 2600 4000 2400 2600 4800
32.42 33201/1024 K713_0320 MB43 50 57 90 122 10.0 5.0 2.0 120 2900 2600 3000 2400 2600 4800
32.42 33201/1024 K713_0320 MB43 72 27 90 122 10.0 5.0 2.0 120 2900 2600 3000 2400 2600 4800
35.44 567/16 K713_0350 MB33 16 94 35 108 10.0 5.0 2.0 120 2900 2600 4000 2400 2600 4800
35.44 567/16 K713_0350 MB33 24 83 35 108 10.0 5.0 2.0 120 2900 2600 4000 2400 2600 4800
35.44 567/16 K713_0350 MB33 32 72 35 108 10.0 5.0 2.0 120 2900 2600 4000 2400 2600 4800
35.44 567/16 K713_0350 MB33 45 54 35 108 10.0 5.0 2.0 120 2900 2600 4000 2400 2600 4800
35.44 567/16 K713_0350 MB43 50 47 83 122 10.0 5.0 2.0 121 2900 2600 3000 2400 2600 4800
35.44 567/16 K713_0350 MB43 72 16 83 122 10.0 5.0 2.0 121 2900 2600 3000 2400 2600 4800
39.23 2511/64 K713_0390 MB33 16 83 35 108 10.0 5.0 2.0 121 2900 2600 4000 2400 2600 4800
39.23 2511/64 K713_0390 MB33 24 72 35 108 10.0 5.0 2.0 121 2900 2600 4000 2400 2600 4800
39.23 2511/64 K713_0390 MB33 32 60 35 108 10.0 5.0 2.0 121 2900 2600 4000 2400 2600 4800
39.23 2511/64 K713_0390 MB33 45 42 35 108 10.0 5.0 2.0 121 2900 2600 4000 2400 2600 4800
39.23 2511/64 K713_0390 MB43 50 35 82 122 10.0 5.0 2.0 122 2900 2600 3000 2400 2600 4800
39.23 2511/64 K713_0390 MB43 72 4.5 82 122 10.0 5.0 2.0 122 2900 2600 3000 2400 2600 4800
45.05 37485/832 K713_0450 MB33 16 69 33 108 10.0 5.0 2.0 122 2900 2600 4000 2400 2600 4800
45.05 37485/832 K713_0450 MB33 24 58 33 108 10.0 5.0 2.0 122 2900 2600 4000 2400 2600 4800
45.05 37485/832 K713_0450 MB33 32 47 33 108 10.0 5.0 2.0 122 2900 2600 4000 2400 2600 4800
45.05 37485/832 K713_0450 MB33 45 29 33 108 10.0 5.0 2.0 122 2900 2600 4000 2400 2600 4800
45.05 37485/832 K713_0450 MB43 50 22 81 122 10.0 5.0 2.0 123 2900 2600 3000 2400 2600 4800
49.88 166005/3328 K713_0500 MB33 16 60 33 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
49.88 166005/3328 K713_0500 MB33 24 49 33 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
49.88 166005/3328 K713_0500 MB33 32 38 33 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
49.88 166005/3328 K713_0500 MB33 45 20 33 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
49.88 166005/3328 K713_0500 MB43 50 13 80 122 10.0 5.0 2.0 123 2900 2600 3000 2400 2600 4800
58.57 7497/128 K713_0590 MB33 16 48 32 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
58.57 7497/128 K713_0590 MB33 24 37 32 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
58.57 7497/128 K713_0590 MB33 32 26 32 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
58.57 7497/128 K713_0590 MB33 45 7.5 32 108 10.0 5.0 2.0 123 2900 2600 4000 2400 2600 4800
58.57 7497/128 K713_0590 MB43 50 0.5 79 122 10.0 5.0 2.0 124 2900 2600 3000 2400 2600 4800
64.85 33201/512 K713_0650 MB33 16 41 31 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
64.85 33201/512 K713_0650 MB33 24 30 31 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
64.85 33201/512 K713_0650 MB33 32 19 31 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
64.85 33201/512 K713_0650 MB33 45 0.7 31 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
71.20 4557/64 K713_0710 MB33 16 30 29 108 10.0 5.0 2.0 124 2900 2600 4000 2173 2600 4346
71.20 4557/64 K713_0710 MB33 24 19 29 108 10.0 5.0 2.0 124 2900 2600 4000 2173 2600 4346
71.20 4557/64 K713_0710 MB33 32 7.7 29 108 10.0 5.0 2.0 124 2900 2600 4000 2173 2600 4346
78.83 20181/256 K713_0790 MB33 16 30 29 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
10.2 Selection tables 10 K helical bevel gear units
276
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K713 (M2acc,max = 2600 Nm)
78.83 20181/256 K713_0790 MB33 24 19 29 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
78.83 20181/256 K713_0790 MB33 32 7.6 29 108 10.0 5.0 2.0 124 2900 2600 4000 2400 2600 4800
89.00 22785/256 K713_0890 MB33 16 9.9 29 108 10.0 5.0 2.0 125 2900 2600 4000 1671 2006 3343
98.54 100905/1024 K713_0990 MB33 16 9.9 29 108 10.0 5.0 2.0 125 2900 2600 4000 1850 2221 3701
K813 (M2acc,max = 4650 Nm)
7.445 3127/420 K813_0074 MB43 50 154 224 176 10.0 5.0 2.0 83 1600 1500 2600 1441 1594 2391
7.445 3127/420 K813_0074 MB43 72 123 224 176 10.0 5.0 2.0 83 1600 1500 2600 1441 1594 2391
7.445 3127/420 K813_0074 MB43 100 84 224 176 10.0 5.0 2.0 83 1600 1500 2600 1441 1594 2391
7.445 3127/420 K813_0074 MB43 160 – 224 176 10.0 5.0 2.0 83 1600 1500 2600 1441 1594 2391
8.243 96937/11760 K813_0082 MB43 50 154 210 176 10.0 5.0 2.0 93 1600 1500 2600 1596 1765 2648
8.243 96937/11760 K813_0082 MB43 72 123 210 176 10.0 5.0 2.0 93 1600 1500 2600 1596 1765 2648
8.243 96937/11760 K813_0082 MB43 100 84 210 176 10.0 5.0 2.0 93 1600 1500 2600 1596 1765 2648
8.243 96937/11760 K813_0082 MB43 160 – 210 176 10.0 5.0 2.0 93 1600 1500 2600 1596 1765 2648
9.284 11977/1290 K813_0093 MB43 50 154 183 176 10.0 5.0 2.0 105 1600 1500 2600 1797 1988 2982
9.284 11977/1290 K813_0093 MB43 72 123 183 176 10.0 5.0 2.0 105 1600 1500 2600 1797 1988 2982
9.284 11977/1290 K813_0093 MB43 100 84 183 176 10.0 5.0 2.0 105 1600 1500 2600 1797 1988 2982
9.284 11977/1290 K813_0093 MB43 160 – 183 176 10.0 5.0 2.0 105 1600 1500 2600 1797 1988 2982
10.28 53041/5160 K813_0105 MB43 50 154 174 176 10.0 5.0 2.0 115 1600 1500 2600 1990 2201 3302
10.28 53041/5160 K813_0105 MB43 72 123 174 176 10.0 5.0 2.0 115 1600 1500 2600 1990 2201 3302
10.28 53041/5160 K813_0105 MB43 100 84 174 176 10.0 5.0 2.0 115 1600 1500 2600 1990 2201 3302
10.28 53041/5160 K813_0105 MB43 160 – 174 176 10.0 5.0 2.0 115 1600 1500 2600 1990 2201 3302
14.84 9499/640 K813_0150 MB43 50 154 132 176 10.0 5.0 2.0 146 1900 1800 3000 2873 3178 4767
14.84 9499/640 K813_0150 MB43 72 123 132 176 10.0 5.0 2.0 146 1900 1800 3000 2873 3178 4767
14.84 9499/640 K813_0150 MB43 100 84 132 176 10.0 5.0 2.0 146 1900 1800 3000 2873 3178 4767
14.84 9499/640 K813_0150 MB43 160 – 132 176 10.0 5.0 2.0 146 1900 1800 3000 2873 3178 4767
16.43 42067/2560 K813_0165 MB43 50 154 128 176 10.0 5.0 2.0 154 1900 1800 3000 3181 3519 5278
16.43 42067/2560 K813_0165 MB43 72 123 128 176 10.0 5.0 2.0 154 1900 1800 3000 3181 3519 5278
16.43 42067/2560 K813_0165 MB43 100 84 128 176 10.0 5.0 2.0 154 1900 1800 3000 3181 3519 5278
16.43 42067/2560 K813_0165 MB43 160 – 128 176 10.0 5.0 2.0 154 1900 1800 3000 3181 3519 5278
17.33 30149/1740 K813_0175 MB33 16 104 69 162 10.0 5.0 2.0 149 2300 2100 3500 1656 1656 3131
17.33 30149/1740 K813_0175 MB33 24 92 69 162 10.0 5.0 2.0 149 2300 2100 3500 1656 1656 3131
17.33 30149/1740 K813_0175 MB33 32 81 69 162 10.0 5.0 2.0 149 2300 2100 3500 1656 1656 3131
17.33 30149/1740 K813_0175 MB33 45 63 69 162 10.0 5.0 2.0 149 2300 2100 3500 1656 1656 3131
17.33 30149/1740 K813_0175 MB33 90 – 69 162 10.0 5.0 2.0 149 2300 2100 3500 1656 1656 3131
17.33 30149/1740 K813_0175 MB43 50 154 122 176 10.0 5.0 2.0 157 2300 2100 3000 3354 3710 5566
17.33 30149/1740 K813_0175 MB43 72 123 122 176 10.0 5.0 2.0 157 2300 2100 3000 3354 3710 5566
17.33 30149/1740 K813_0175 MB43 100 84 122 176 10.0 5.0 2.0 157 2300 2100 3000 3354 3710 5566
17.33 30149/1740 K813_0175 MB43 160 – 122 176 10.0 5.0 2.0 157 2300 2100 3000 3354 3710 5566
19.18 133517/6960 K813_0190 MB33 16 104 66 162 10.0 5.0 2.0 156 2300 2100 3500 1834 1834 3466
19.18 133517/6960 K813_0190 MB33 24 92 66 162 10.0 5.0 2.0 156 2300 2100 3500 1834 1834 3466
19.18 133517/6960 K813_0190 MB33 32 81 66 162 10.0 5.0 2.0 156 2300 2100 3500 1834 1834 3466
19.18 133517/6960 K813_0190 MB33 45 63 66 162 10.0 5.0 2.0 156 2300 2100 3500 1834 1834 3466
19.18 133517/6960 K813_0190 MB33 90 – 66 162 10.0 5.0 2.0 156 2300 2100 3500 1834 1834 3466
19.18 133517/6960 K813_0190 MB43 50 154 119 176 10.0 5.0 2.0 163 2300 2100 3000 3579 4108 6162
19.18 133517/6960 K813_0190 MB43 72 123 119 176 10.0 5.0 2.0 163 2300 2100 3000 3579 4108 6162
19.18 133517/6960 K813_0190 MB43 100 84 119 176 10.0 5.0 2.0 163 2300 2100 3000 3579 4108 6162
19.18 133517/6960 K813_0190 MB43 160 – 119 176 10.0 5.0 2.0 163 2300 2100 3000 3579 4108 6162
23.04 31801/1380 K813_0230 MB33 16 104 55 162 10.0 5.0 2.0 166 2300 2100 3500 2203 2203 4164
23.04 31801/1380 K813_0230 MB33 24 92 55 162 10.0 5.0 2.0 166 2300 2100 3500 2203 2203 4164
23.04 31801/1380 K813_0230 MB33 32 81 55 162 10.0 5.0 2.0 166 2300 2100 3500 2203 2203 4164
23.04 31801/1380 K813_0230 MB33 45 63 55 162 10.0 5.0 2.0 166 2300 2100 3500 2203 2203 4164
23.04 31801/1380 K813_0230 MB33 90 – 55 162 10.0 5.0 2.0 166 2300 2100 3500 2203 2203 4164
23.04 31801/1380 K813_0230 MB43 50 154 108 176 10.0 5.0 2.0 172 2300 2100 3000 3805 4650 7402
23.04 31801/1380 K813_0230 MB43 72 123 108 176 10.0 5.0 2.0 172 2300 2100 3000 3805 4650 7402
23.04 31801/1380 K813_0230 MB43 100 84 108 176 10.0 5.0 2.0 172 2300 2100 3000 3805 4650 7402
23.04 31801/1380 K813_0230 MB43 160 – 108 176 10.0 5.0 2.0 172 2300 2100 3000 3805 4650 7402
25.51 140833/5520 K813_0260 MB33 16 104 54 162 10.0 5.0 2.0 171 2300 2100 3500 2439 2439 4610
25.51 140833/5520 K813_0260 MB33 24 92 54 162 10.0 5.0 2.0 171 2300 2100 3500 2439 2439 4610
25.51 140833/5520 K813_0260 MB33 32 81 54 162 10.0 5.0 2.0 171 2300 2100 3500 2439 2439 4610
25.51 140833/5520 K813_0260 MB33 45 63 54 162 10.0 5.0 2.0 171 2300 2100 3500 2439 2439 4610
25.51 140833/5520 K813_0260 MB33 90 – 54 162 10.0 5.0 2.0 171 2300 2100 3500 2439 2439 4610
25.51 140833/5520 K813_0260 MB43 50 154 107 176 10.0 5.0 2.0 176 2300 2100 3000 3936 4650 8195
25.51 140833/5520 K813_0260 MB43 72 123 107 176 10.0 5.0 2.0 176 2300 2100 3000 3936 4650 8195
25.51 140833/5520 K813_0260 MB43 100 84 107 176 10.0 5.0 2.0 176 2300 2100 3000 3936 4650 8195
10 K helical bevel gear units 10.2 Selection tables
277
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K813 (M2acc,max = 4650 Nm)
25.51 140833/5520 K813_0260 MB43 160 – 107 176 10.0 5.0 2.0 176 2300 2100 3000 3936 4650 8195
29.25 7021/240 K813_0290 MB33 16 104 47 162 10.0 5.0 2.0 176 2800 2500 4000 2797 2797 5286
29.25 7021/240 K813_0290 MB33 24 92 47 162 10.0 5.0 2.0 176 2800 2500 4000 2797 2797 5286
29.25 7021/240 K813_0290 MB33 32 81 47 162 10.0 5.0 2.0 176 2800 2500 4000 2797 2797 5286
29.25 7021/240 K813_0290 MB33 45 63 47 162 10.0 5.0 2.0 176 2800 2500 4000 2797 2797 5286
29.25 7021/240 K813_0290 MB33 90 – 47 162 10.0 5.0 2.0 176 2800 2500 4000 2797 2797 5286
29.25 7021/240 K813_0290 MB43 50 154 100 176 10.0 5.0 2.0 180 2800 2500 3000 4120 4650 8400
29.25 7021/240 K813_0290 MB43 72 123 100 176 10.0 5.0 2.0 180 2800 2500 3000 4120 4650 8400
29.25 7021/240 K813_0290 MB43 100 84 100 176 10.0 5.0 2.0 180 2800 2500 3000 4120 4650 8400
29.25 7021/240 K813_0290 MB43 160 – 100 176 10.0 5.0 2.0 180 2800 2500 3000 4120 4650 8400
32.39 31093/960 K813_0320 MB33 16 104 46 162 10.0 5.0 2.0 180 2800 2500 4000 3096 3096 5852
32.39 31093/960 K813_0320 MB33 24 92 46 162 10.0 5.0 2.0 180 2800 2500 4000 3096 3096 5852
32.39 31093/960 K813_0320 MB33 32 81 46 162 10.0 5.0 2.0 180 2800 2500 4000 3096 3096 5852
32.39 31093/960 K813_0320 MB33 45 63 46 162 10.0 5.0 2.0 180 2800 2500 4000 3096 3096 5852
32.39 31093/960 K813_0320 MB33 90 – 46 162 10.0 5.0 2.0 180 2800 2500 4000 3096 3096 5852
32.39 31093/960 K813_0320 MB43 50 153 99 176 10.0 5.0 2.0 183 2800 2500 3000 4200 4650 8400
32.39 31093/960 K813_0320 MB43 72 122 99 176 10.0 5.0 2.0 183 2800 2500 3000 4200 4650 8400
32.39 31093/960 K813_0320 MB43 100 83 99 176 10.0 5.0 2.0 183 2800 2500 3000 4200 4650 8400
36.14 2891/80 K813_0360 MB33 16 104 42 162 10.0 5.0 2.0 183 2800 2500 4000 3187 3455 6530
36.14 2891/80 K813_0360 MB33 24 92 42 162 10.0 5.0 2.0 183 2800 2500 4000 3187 3455 6530
36.14 2891/80 K813_0360 MB33 32 81 42 162 10.0 5.0 2.0 183 2800 2500 4000 3187 3455 6530
36.14 2891/80 K813_0360 MB33 45 63 42 162 10.0 5.0 2.0 183 2800 2500 4000 3187 3455 6530
36.14 2891/80 K813_0360 MB33 90 – 42 162 10.0 5.0 2.0 183 2800 2500 4000 3187 3455 6530
36.14 2891/80 K813_0360 MB43 50 130 95 176 10.0 5.0 2.0 186 2800 2500 3000 4200 4650 8400
36.14 2891/80 K813_0360 MB43 72 99 95 176 10.0 5.0 2.0 186 2800 2500 3000 4200 4650 8400
36.14 2891/80 K813_0360 MB43 100 60 95 176 10.0 5.0 2.0 186 2800 2500 3000 4200 4650 8400
40.01 12803/320 K813_0400 MB33 16 104 41 162 10.0 5.0 2.0 185 2800 2500 4000 3528 3825 7229
40.01 12803/320 K813_0400 MB33 24 92 41 162 10.0 5.0 2.0 185 2800 2500 4000 3528 3825 7229
40.01 12803/320 K813_0400 MB33 32 81 41 162 10.0 5.0 2.0 185 2800 2500 4000 3528 3825 7229
40.01 12803/320 K813_0400 MB33 45 63 41 162 10.0 5.0 2.0 185 2800 2500 4000 3528 3825 7229
40.01 12803/320 K813_0400 MB33 90 – 41 162 10.0 5.0 2.0 185 2800 2500 4000 3528 3825 7229
40.01 12803/320 K813_0400 MB43 50 111 94 176 10.0 5.0 2.0 188 2800 2500 3000 4200 4650 8400
40.01 12803/320 K813_0400 MB43 72 80 94 176 10.0 5.0 2.0 188 2800 2500 3000 4200 4650 8400
40.01 12803/320 K813_0400 MB43 100 41 94 176 10.0 5.0 2.0 188 2800 2500 3000 4200 4650 8400
44.25 177/4 K813_0440 MB33 16 104 38 162 10.0 5.0 2.0 187 2800 2500 4000 3373 4230 7995
44.25 177/4 K813_0440 MB33 24 92 38 162 10.0 5.0 2.0 187 2800 2500 4000 3373 4230 7995
44.25 177/4 K813_0440 MB33 32 81 38 162 10.0 5.0 2.0 187 2800 2500 4000 3373 4230 7995
44.25 177/4 K813_0440 MB33 45 63 38 162 10.0 5.0 2.0 187 2800 2500 4000 3373 4230 7995
44.25 177/4 K813_0440 MB33 90 – 38 162 10.0 5.0 2.0 187 2800 2500 4000 3373 4230 7995
44.25 177/4 K813_0440 MB43 50 93 86 176 10.0 5.0 2.0 189 2800 2500 3000 4200 4650 8400
44.25 177/4 K813_0440 MB43 72 63 86 176 10.0 5.0 2.0 189 2800 2500 3000 4200 4650 8400
44.25 177/4 K813_0440 MB43 100 23 86 176 10.0 5.0 2.0 189 2800 2500 3000 4200 4650 8400
48.99 5487/112 K813_0490 MB33 16 104 38 162 10.0 5.0 2.0 189 2800 2500 4000 3734 4650 8400
48.99 5487/112 K813_0490 MB33 24 92 38 162 10.0 5.0 2.0 189 2800 2500 4000 3734 4650 8400
48.99 5487/112 K813_0490 MB33 32 81 38 162 10.0 5.0 2.0 189 2800 2500 4000 3734 4650 8400
48.99 5487/112 K813_0490 MB33 45 63 38 162 10.0 5.0 2.0 189 2800 2500 4000 3734 4650 8400
48.99 5487/112 K813_0490 MB33 90 – 38 162 10.0 5.0 2.0 189 2800 2500 4000 3734 4650 8400
48.99 5487/112 K813_0490 MB43 50 78 85 176 10.0 5.0 2.0 190 2800 2500 3000 4200 4650 8400
48.99 5487/112 K813_0490 MB43 72 47 85 176 10.0 5.0 2.0 190 2800 2500 3000 4200 4650 8400
48.99 5487/112 K813_0490 MB43 100 7.5 85 176 10.0 5.0 2.0 190 2800 2500 3000 4200 4650 8400
59.08 42539/720 K813_0590 MB33 16 100 35 162 10.0 5.0 2.0 191 2800 2500 4000 3464 4650 8400
59.08 42539/720 K813_0590 MB33 24 89 35 162 10.0 5.0 2.0 191 2800 2500 4000 3464 4650 8400
59.08 42539/720 K813_0590 MB33 32 78 35 162 10.0 5.0 2.0 191 2800 2500 4000 3464 4650 8400
59.08 42539/720 K813_0590 MB33 45 59 35 162 10.0 5.0 2.0 191 2800 2500 4000 3464 4650 8400
59.08 42539/720 K813_0590 MB43 50 52 82 176 10.0 5.0 2.0 192 2800 2500 3000 4200 4650 8400
59.08 42539/720 K813_0590 MB43 72 22 82 176 10.0 5.0 2.0 192 2800 2500 3000 4200 4650 8400
65.41 188387/2880 K813_0650 MB33 16 88 34 162 10.0 5.0 2.0 192 2800 2500 4000 3836 4650 8400
65.41 188387/2880 K813_0650 MB33 24 77 34 162 10.0 5.0 2.0 192 2800 2500 4000 3836 4650 8400
65.41 188387/2880 K813_0650 MB33 32 66 34 162 10.0 5.0 2.0 192 2800 2500 4000 3836 4650 8400
65.41 188387/2880 K813_0650 MB33 45 47 34 162 10.0 5.0 2.0 192 2800 2500 4000 3836 4650 8400
65.41 188387/2880 K813_0650 MB43 50 40 82 176 10.0 5.0 2.0 193 2800 2500 3000 4200 4650 8400
65.41 188387/2880 K813_0650 MB43 72 9.7 82 176 10.0 5.0 2.0 193 2800 2500 3000 4200 4650 8400
71.70 10325/144 K813_0720 MB33 16 64 33 162 10.0 5.0 2.0 193 2800 2500 4000 3579 4327 7212
71.70 10325/144 K813_0720 MB33 24 53 33 162 10.0 5.0 2.0 193 2800 2500 4000 3579 4327 7212
10.2 Selection tables 10 K helical bevel gear units
278
i iexakt Type M1Bstat MM,Bmax J1 m Δφ2 Δφ2redII Δφ2redI C2 n1maxDB n1maxZB M2N M2acc M2NOT
EL1,2,3,4 EL5,6
[Nm] [Nm] [kgcm²] [kg] [arcmin] [arcmin] [arcmin] [Nm/ [rpm] [rpm] [rpm] [Nm] [Nm] [Nm]
arcmin]
K813 (M2acc,max = 4650 Nm)
71.70 10325/144 K813_0720 MB33 32 42 33 162 10.0 5.0 2.0 193 2800 2500 4000 3579 4327 7212
71.70 10325/144 K813_0720 MB33 45 24 33 162 10.0 5.0 2.0 193 2800 2500 4000 3579 4327 7212
71.70 10325/144 K813_0720 MB43 50 17 81 176 10.0 5.0 2.0 193 2800 2500 3000 3606 4327 7212
79.38 45725/576 K813_0790 MB33 16 64 33 162 10.0 5.0 2.0 193 2800 2500 4000 3962 4650 7986
79.38 45725/576 K813_0790 MB33 24 53 33 162 10.0 5.0 2.0 193 2800 2500 4000 3962 4650 7986
79.38 45725/576 K813_0790 MB33 32 42 33 162 10.0 5.0 2.0 193 2800 2500 4000 3962 4650 7986
79.38 45725/576 K813_0790 MB33 45 24 33 162 10.0 5.0 2.0 193 2800 2500 4000 3962 4650 7986
79.38 45725/576 K813_0790 MB43 50 17 80 176 10.0 5.0 2.0 194 2800 2500 3000 3993 4650 7986
87.76 7021/80 K813_0880 MB33 16 33 30 162 10.0 5.0 2.0 194 2800 2500 4000 2805 3366 5610
87.76 7021/80 K813_0880 MB33 24 21 30 162 10.0 5.0 2.0 194 2800 2500 4000 2805 3366 5610
87.76 7021/80 K813_0880 MB33 32 10 30 162 10.0 5.0 2.0 194 2800 2500 4000 2805 3366 5610
97.17 31093/320 K813_0970 MB33 16 33 30 162 10.0 5.0 2.0 194 2800 2500 4000 3106 3727 6211
97.17 31093/320 K813_0970 MB33 24 21 30 162 10.0 5.0 2.0 194 2800 2500 4000 3106 3727 6211
97.17 31093/320 K813_0970 MB33 32 10 30 162 10.0 5.0 2.0 194 2800 2500 4000 3106 3727 6211
K913 (M2acc,max = 7700 Nm)
12.53 73749/5888 K913_0125 MB43 50 154 240 290 10.0 5.0 – 197 1800 1800 2800 2425 2682 4023
12.53 73749/5888 K913_0125 MB43 72 123 240 290 10.0 5.0 – 197 1800 1800 2800 2425 2682 4023
12.53 73749/5888 K913_0125 MB43 100 84 240 290 10.0 5.0 – 197 1800 1800 2800 2425 2682 4023
12.53 73749/5888 K913_0125 MB43 160 – 240 290 10.0 5.0 – 197 1800 1800 2800 2425 2682 4023
19.06 305/16 K913_0190 MB43 50 154 167 290 10.0 5.0 – 271 2200 2100 3000 3690 4082 6123
19.06 305/16 K913_0190 MB43 72 123 167 290 10.0 5.0 – 271 2200 2100 3000 3690 4082 6123
19.06 305/16 K913_0190 MB43 100 84 167 290 10.0 5.0 – 271 2200 2100 3000 3690 4082 6123
19.06 305/16 K913_0190 MB43 160 – 167 290 10.0 5.0 – 271 2200 2100 3000 3690 4082 6123
23.94 88877/3712 K913_0240 MB43 50 154 143 290 10.0 5.0 – 303 2200 2100 3000 4635 5127 7691
23.94 88877/3712 K913_0240 MB43 72 123 143 290 10.0 5.0 – 303 2200 2100 3000 4635 5127 7691
23.94 88877/3712 K913_0240 MB43 100 84 143 290 10.0 5.0 – 303 2200 2100 3000 4635 5127 7691
23.94 88877/3712 K913_0240 MB43 160 – 143 290 10.0 5.0 – 303 2200 2100 3000 4635 5127 7691
32.12 47275/1472 K913_0320 MB43 50 154 121 290 10.0 5.0 – 332 2600 2500 3000 6217 6877 10316
32.12 47275/1472 K913_0320 MB43 72 123 121 290 10.0 5.0 – 332 2600 2500 3000 6217 6877 10316
32.12 47275/1472 K913_0320 MB43 100 84 121 290 10.0 5.0 – 332 2600 2500 3000 6217 6877 10316
32.12 47275/1472 K913_0320 MB43 160 – 121 290 10.0 5.0 – 332 2600 2500 3000 6217 6877 10316
38.04 194773/5120 K913_0380 MB43 50 154 112 290 10.0 5.0 – 345 2600 2500 3000 6776 7700 12220
38.04 194773/5120 K913_0380 MB43 72 123 112 290 10.0 5.0 – 345 2600 2500 3000 6776 7700 12220
38.04 194773/5120 K913_0380 MB43 100 84 112 290 10.0 5.0 – 345 2600 2500 3000 6776 7700 12220
38.04 194773/5120 K913_0380 MB43 160 – 112 290 10.0 5.0 – 345 2600 2500 3000 6776 7700 12220
48.94 100223/2048 K913_0490 MB43 50 154 102 290 10.0 5.0 – 357 2600 2500 3000 7000 7700 14000
48.94 100223/2048 K913_0490 MB43 72 123 102 290 10.0 5.0 – 357 2600 2500 3000 7000 7700 14000
48.94 100223/2048 K913_0490 MB43 100 84 102 290 10.0 5.0 – 357 2600 2500 3000 7000 7700 14000
48.94 100223/2048 K913_0490 MB43 160 – 102 290 10.0 5.0 – 357 2600 2500 3000 7000 7700 14000
63.07 209901/3328 K913_0630 MB43 50 121 95 290 10.0 5.0 – 366 2600 2500 3000 7000 7700 14000
63.07 209901/3328 K913_0630 MB43 72 90 95 290 10.0 5.0 – 366 2600 2500 3000 7000 7700 14000
63.07 209901/3328 K913_0630 MB43 100 51 95 290 10.0 5.0 – 366 2600 2500 3000 7000 7700 14000
75.00 62403/832 K913_0750 MB43 50 91 86 290 10.0 5.0 – 370 2600 2500 3000 7000 7700 14000
75.00 62403/832 K913_0750 MB43 72 60 86 290 10.0 5.0 – 370 2600 2500 3000 7000 7700 14000
75.00 62403/832 K913_0750 MB43 100 21 86 290 10.0 5.0 – 370 2600 2500 3000 7000 7700 14000
95.41 293105/3072 K913_0950 MB43 50 27 83 290 10.0 5.0 – 373 2600 2500 3000 5375 6450 10751
10 K helical bevel gear units 10.2 Selection tables
279
10.2 Selection tables 10 K helical bevel gear units
280
10.3 Dimensional drawings
In this chapter, you can find the dimensions of the gear units as well as example dimensions of the mountable motor adapters.
Dimensions can exceed the specifications of ISO 2768-mK due to casting tolerances or accumulation of individual tolerances.
We reserve the right to make dimensional changes due to ongoing technical development.
You can download 3D models of our standard drives at https://configurator.stoeber.de/en-US/.
Tolerances
Axis height in accordance with DIN 747 Tolerance
Up to 50 mm -0.4 mm
Up to 250 mm -0.5 mm
Up to 630 mm -0.6 mm
Solid shaft Tolerance
Shaft ∅ fit ≤ 50 mm DIN 748-1, ISO k6
Shaft ∅ fit > 50 mm DIN 748-1, ISO m6
Feather keys DIN 6885-1, high form A
Hollow shaft Tolerance
Hollow shaft hole fit ISO H7
Feather keys DIN 6885-1, high form
K1 ∅30: DIN 6885-3, low form
Flange Pilot tolerance
Up to 300 mm ISO j6
Starting at 350 mm ISO h6
Centering holes in solid shafts in accordance with DIN 332-2, DR shape
Thread size M4 M5 M6 M8 M10 M12 M16 M20 M24
Thread depth
[mm]
10 12.5 16 19 22 28 36 42 50
10 K helical bevel gear units 10.3 Dimensional drawings
281
10.3.1 A shaft design (hollow shaft), G housing design (pitch circle diameter)
1) The length of the machine shaft must be at least 2.2 x
∅dh and the length of the feather key must be at least 2 x
∅dh.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
282
Dimensions of gear units
Type ☐a4 ∅b b3 b4 b5 b7 b8 B B2 ∅dh ∅Dh Dha ∅e f h H i2 le lh las lha m1 s3 s4 sm sas t3 t4 th uh
K1 105 75j6 30 90 30 90 70 90 106 20H7 40 ☐105 90 3.0 60 160 7.0 98.0 120 12 127.0 60 M8 M8 M6 M8 13 13 22.8 6
JS9
K1 105 75j6 30 90 30 90 70 90 106 25H7 40 ☐105 90 3.0 60 160 7.0 98.0 120 12 127.0 60 M8 M8 M10 M12 13 13 28.3 8
JS9
K1 105 75j6 30 90 30 90 70 90 106 30H7 40 ☐105 90 3.0 60 160 7.0 93.5 120 12 127.0 60 M8 M8 M10 M12 13 13 32.0 8
JS9
K2 116 82j6 35 115 35 115 90 115 134 30H7 45 ☐116 100 3.0 65 190 7.0 121.5 148 12 156.0 65 M10 M8 M10 M12 16 13 33.3 8
JS9
K3 132 95j6 40 130 40 130 105 130 146 35H7 50 ☐132 115 3.0 75 213 7.0 125.0 160 12 168.0 75 M10 M8 M12 M16 16 13 38.3 10JS9
K4 152 110j6 50 155 50 155 120 148 173 40H7 55 ☐152 130 3.5 90 240 7.5 157.0 188 12 197.5 90 M12 M10 M16 M20 19 16 43.3 12JS9
K5 145 110j6 40 140 100 140 125 160 185 50H7 65 ☐145 130 3.5 160 260 7.5 164.0 200 12 209.5 100 M16 M10 M16 M20 26 16 53.8 14JS9
K6 180 140j6 50 160 110 160 130 168 200 50H7 70 ∅183 165 3.5 190 310 7.5 179.0 215 12 224.5 120 M16 M10 M16 M20 26 16 53.8 14JS9
K7 195 155j6 55 180 125 180 145 190 226 60H7 85 ∅205 185 3.5 212 342 8.0 214.0 242 12 252.0 125 M20 M12 M20 M24 33 19 64.4 18JS9
K8 226 185j6 75 240 165 240 185 235 282 70H7 100 ∅184 215 4.0 265 410 9.0 263.0 300 20 311.0 145 M24 M12 M20 M24 38 19 74.9 20JS9
K9 280 230j6 95 280 185 280 225 285 330 90H7 120 ∅230 265 5.0 315 495 10.0 302.0 350 26 361.0 180 M30 M16 M24 M30 48 26 95.4 25JS9
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
283
10.3.2 A shaft design (hollow shaft), NG housing design (foot + pitch circle
diameter)
1) The length of the machine shaft must be at least 2.2 x
∅dh and the length of the feather key must be at least 2 x
∅dh.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
284
Dimensions of gear units
Typ
e
a0 ☐a4 ∅b b3 b4 b5 b7 B B2 ∅dh ∅Dh Dha ∅e f h H i2 le lh las lha m1 n2 n3 n4 n5 ∅s s4 sm sas t4 th uh
K1 115 105 75j6 30 90 30 90 90 106 20H7 40 ☐105 90 3.0 75 175 7.0 98.0 120 12 127.0 75 30 13 140 15 9.0 M8 M6 M8 13 22.8 6
JS9
K1 115 105 75j6 30 90 30 90 90 106 25H7 40 ☐105 90 3.0 75 175 7.0 98.0 120 12 127.0 75 30 13 140 15 9.0 M8 M10 M12 13 28.3 8
JS9
K1 115 105 75j6 30 90 30 90 90 106 30H7 40 ☐105 90 3.0 75 175 7.0 93.5 120 12 127.0 75 30 13 140 15 9.0 M8 M10 M12 13 32.0 8
JS9
K2 155 116 82j6 35 115 35 115 115 134 30H7 45 ☐116 100 3.0 88 213 7.0 121.5 148 12 156.0 88 40 20 185 23 11.0 M8 M10 M12 13 33.3 8
JS9
K3 170 132 95j6 40 130 40 130 130 146 35H7 50 ☐132 115 3.0 98 236 7.0 125.0 160 12 168.0 98 45 20 200 23 11.0 M8 M12 M16 13 38.3 10JS9
K4 200 152 110j6 50 155 50 155 148 173 40H7 55 ☐152 130 3.5 115 265 7.5 157.0 188 12 197.5 115 50 22 230 25 14.0 M10 M16 M20 16 43.3 12JS9
K5 200 145 110j6 40 140 100 140 160 185 50H7 65 ☐145 130 3.5 190 290 7.5 164.0 200 12 209.5 130 60 27 240 30 18.0 M10 M16 M20 16 53.8 14JS9
K6 210 180 140j6 50 160 110 160 168 200 50H7 70 ∅183 165 3.5 220 340 7.5 179.0 215 12 224.5 150 65 27 250 30 18.5 M10 M16 M20 16 53.8 14JS9
K7 241 195 155j6 55 180 125 180 190 226 60H7 85 ∅205 185 3.5 250 380 8.0 214.0 242 12 252.0 163 70 35 290 38 23.0 M12 M20 M24 19 64.4 18JS9
K8 300 226 185j6 75 240 165 240 235 282 70H7 100 ∅184 215 4.0 310 455 9.0 263.0 300 20 311.0 190 85 41 360 45 27.0 M12 M20 M24 19 74.9 20JS9
K9 360 280 230j6 95 280 185 280 285 330 90H7 120 ∅230 265 5.0 365 545 10.0 302.0 350 26 361.0 230 95 46 430 50 31.0 M16 M24 M30 26 95.4 25JS9
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
285
10.3.3 A shaft design (hollow shaft), GD housing design (pitch circle diameter +
torque arm bracket)
1) The length of the machine shaft must be at least 2.2 x
∅dh and the length of the feather key must be at least 2 x
∅dh.
2) Cover (optional)
3) Only for K1 (other sizes on request) − If you brace the gear units without the torque arm brackets provided by the manufacturer for this purpose, the dimensions for ad2 and ad3 must meet the specified value.
10.3 Dimensional drawings 10 K helical bevel gear units
286
Dimensions of gear units
Type ☐a4 ad ad1 ad2 ad3 ad4 ad5 ∅b B B2 ∅dd ∅dh ∅Dd ∅Dh Dha ∅e f
K1 105 6.0 15.0 90 90 15.0 130 75j6 90 106 12H9 20H7 43 40 ☐105 90 3.0
K1 105 6.0 15.0 90 90 15.0 130 75j6 90 106 12H9 25H7 43 40 ☐105 90 3.0
K1 105 6.0 15.0 90 90 15.0 130 75j6 90 106 12H9 30H7 43 40 ☐105 90 3.0
K2 116 6.5 22.5 100 100 22.5 – 82j6 115 134 16H9 30H7 45 45 ☐116 100 3.0
K3 132 5.0 25.0 120 120 25.0 – 95j6 130 146 16H9 35H7 45 50 ☐132 115 3.0
K4 152 9.5 27.5 150 150 27.5 – 110j6 148 173 20H9 40H7 55 55 ☐152 130 3.5
K5 145 9.5 30.0 250 190 30.0 – 110j6 160 185 20H9 50H7 58 65 ☐145 130 3.5
K6 180 13.0 30.0 250 180 30.0 – 140j6 168 200 20H9 50H7 58 70 ∅183 165 3.5
K7 195 15.0 35.0 300 213 35.0 – 155j6 190 226 20H9 60H7 68 85 ∅205 185 3.5
K8 226 17.0 45.0 350 230 45.0 – 185j6 235 282 24H9 70H7 72 100 ∅184 215 4.0
K9 280 16.0 45.0 450 315 45.0 – 230j6 285 330 24H9 90H7 75 120 ∅230 265 5.0
Type h H i2 ld ld1 le lh las lha m1 s4 sm sas t4 th uh
K1 60 160 7.0 24 28 98.0 120 12 127.0 60 M8 M6 M8 13 22.8 6
JS9
K1 60 160 7.0 24 28 98.0 120 12 127.0 60 M8 M10 M12 13 28.3 8
JS9
K1 60 160 7.0 24 28 93.5 120 12 127.0 60 M8 M10 M12 13 32.0 8
JS9
K2 65 190 7.0 32 38 121.5 148 12 156.0 65 M8 M10 M12 13 33.3 8
JS9
K3 75 213 7.0 32 38 125.0 160 12 168.0 75 M8 M12 M16 13 38.3 10JS9
K4 90 240 7.5 40 46 157.0 188 12 197.5 90 M10 M16 M20 16 43.3 12JS9
K5 160 260 7.5 40 46 164.0 200 12 209.5 100 M10 M16 M20 16 53.8 14JS9
K6 190 310 7.5 40 46 179.0 215 12 224.5 120 M10 M16 M20 16 53.8 14JS9
K7 212 342 8.0 64 70 214.0 242 12 252.0 125 M12 M20 M24 19 64.4 18JS9
K8 265 410 9.0 102 115 263.0 300 20 311.0 145 M12 M20 M24 19 74.9 20JS9
K9 315 495 10.0 102 115 302.0 350 26 361.0 180 M16 M24 M30 26 95.4 25JS9
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
287
10.3.4 A shaft design (hollow shaft), F housing design (round flange)
1) The length of the machine shaft must be at least 2.2 x
∅dh and the length of the feather key must be at least 2 x
∅dh.
2) Cover (optional)
10.3 Dimensional drawings 10 K helical bevel gear units
288
Dimensions of gear units
Type ∅a1 ∅b1 b8 B B2 c1 c2 ∅dh ∅Dh Dha ∅e1 f1 h H i2 le lh las lha m1 ∅s1 sm sas th uh
K1 160 110j6 70 90 106 10 32.0 20H7 40 ☐105 130 3.5 60 160 25.0 98.0 120 12 127.0 60 9 M6 M8 22.8 6
JS9
K1 160 110j6 70 90 106 10 32.0 25H7 40 ☐105 130 3.5 60 160 25.0 98.0 120 12 127.0 60 9 M10 M12 28.3 8
JS9
K1 160 110j6 70 90 106 10 32.0 30H7 40 ☐105 130 3.5 60 160 25.0 93.5 120 12 127.0 60 9 M10 M12 32.0 8
JS9
K2 200 130j6 90 115 134 12 32.0 30H7 45 ☐116 165 3.5 65 190 25.0 121.5 148 12 156.0 65 11 M10 M12 33.3 8
JS9
K3 200 130j6 105 130 146 14 38.0 35H7 50 ☐132 165 3.5 75 213 31.0 125.0 160 12 168.0 75 11 M12 M16 38.3 10JS9
K4 250 180j6 120 148 173 15 40.0 40H7 55 ☐152 215 4.0 90 240 32.5 157.0 188 12 197.5 90 14 M16 M20 43.3 12JS9
K5 250 180j6 125 160 185 15 39.5 50H7 65 ☐145 215 4.0 160 260 32.0 164.0 200 12 209.5 100 14 M16 M20 53.8 14JS9
K6 300 230j6 130 168 200 17 36.0 50H7 70 ∅183 265 4.0 190 310 28.5 179.0 215 12 224.5 120 14 M16 M20 53.8 14JS9
K7 350 250h6 145 190 226 18 44.0 60H7 85 ∅205 300 5.0 212 342 36.0 214.0 242 12 252.0 125 18 M20 M24 64.4 18JS9
K8 400 300h6 185 235 282 20 45.0 70H7 100 ∅184 350 5.0 265 410 36.0 263.0 300 20 311.0 145 18 M20 M24 74.9 20JS9
K9 450 350h6 225 285 330 23 50.0 90H7 120 ∅230 400 5.0 315 495 40.0 302.0 350 26 361.0 180 18 M24 M30 95.4 25JS9
Dimensions of additional round flanges
Type ∅a1 ∅b1 c1 ∅e1 f1 ∅s1
K1 140 95j6 10 115 3.0 9
K2 160 110j6 12 130 3.5 9
K3 160 110j6 14 130 3.5 9
K3 250 180j6 14 215 4.0 14
K8 350 250h6 18 300 5.0 18
K8 450 350h6 20 400 5.0 18
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
289
10.3.5 A shaft design (hollow shaft), NF housing design (foot + round flange)
1) The length of the machine shaft must be at least 2.2 x
∅dh and the length of the feather key must be at least 2 x
∅dh.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
290
Dimensions of gear units
Type a0 ∅a1 ∅b1 b3 b4 b5 b7 B B2 c1 c2 ∅dh ∅Dh Dha ∅e1 f1 h
K1 115 160 110j6 30 90 30 90 90 106 10 32.0 20H7 40 ☐105 130 3.5 75
K1 115 160 110j6 30 90 30 90 90 106 10 32.0 25H7 40 ☐105 130 3.5 75
K1 115 160 110j6 30 90 30 90 90 106 10 32.0 30H7 40 ☐105 130 3.5 75
K5 200 250 180j6 40 140 100 140 160 185 15 39.5 50H7 65 ☐145 215 4.0 190
K6 210 300 230j6 50 160 110 160 168 200 17 36.0 50H7 70 ∅183 265 4.0 220
K7 241 350 250h6 55 180 125 180 190 226 18 44.0 60H7 85 ∅205 300 5.0 250
K8 300 400 300h6 75 240 165 240 235 282 20 45.0 70H7 100 ∅184 350 5.0 310
K9 360 450 350h6 95 280 185 280 285 330 23 50.0 90H7 120 ∅230 400 5.0 365
Type H i2 le lh las lha m1 n2 n3 n4 n5 ∅s ∅s1 sm sas th uh
K1 175 25.0 98.0 120 12 127.0 75 30 13 140 15 9.0 9 M6 M8 22.8 6
JS9
K1 175 25.0 98.0 120 12 127.0 75 30 13 140 15 9.0 9 M10 M12 28.3 8
JS9
K1 175 25.0 93.5 120 12 127.0 75 30 13 140 15 9.0 9 M10 M12 32.0 8
JS9
K5 290 32.0 164.0 200 12 209.5 130 60 27 240 30 18.0 14 M16 M20 53.8 14JS9
K6 340 28.5 179.0 215 12 224.5 150 65 27 250 30 18.5 14 M16 M20 53.8 14JS9
K7 380 36.0 214.0 242 12 252.0 163 70 35 290 38 23.0 18 M20 M24 64.4 18JS9
K8 455 36.0 263.0 300 20 311.0 190 85 41 360 45 27.0 18 M20 M24 74.9 20JS9
K9 545 40.0 302.0 350 26 361.0 230 95 46 430 50 31.0 18 M24 M30 95.4 25JS9
Dimensions of additional round flanges
Type ∅a1 ∅b1 c1 c2 ∅e1 f1 ∅s1
K1 140 95j6 10 32 115 3 9
K8 350 250h6 18 45 300 5 18
K8 450 350h6 20 45 400 5 18
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
291
10.3.6 S shaft design (hollow shaft with shrink ring), G housing design (pitch circle
diameter)
1) Machine shaft: The dimension ls must meet or exceed the
specified value.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
292
Dimensions of gear units
Typ
e
☐a4 ∅b b3 b4 b5 b7 b8 B B2 ∅ds ∅ds1 ∅ds2 ∅dss ∅Ds ∅Dsa ∅Dss ∅e f h H i2 ls lsa m1 m2 m3 m4 m5 s3 s4 t3 t4
K1 105 75j6 30 90 30 90 70 90 106 25h9 25h9
H7 25.5 30 40 80 60 90 3.0 60 160 7.0 149 163 60 20 34 25 29 M8 M8 13 13
K2 116 82j6 35 115 35 115 90 115 134 30h9 30h9
H7 30.5 36 45 88 72 100 3.0 65 190 7.0 178 193 65 25 39 30 34 M10 M8 16 13
K3 132 95j6 40 130 40 130 105 130 146 35h9 35h9
H7 35.5 44 50 101 80 115 3.0 75 213 7.0 190 206 75 30 39 35 34 M10 M8 16 13
K4 152 110j6 50 155 50 155 120 148 173 40h9 40h9
H7 40.5 50 55 114 88 130 3.5 90 240 7.5 220 243 90 40 39 45 34 M12 M10 19 16
K5 145 110j6 40 140 100 140 125 160 185 50h9 50h9
H7 50.5 62 65 116 106 130 3.5 160 260 7.5 237 254 100 40 44 45 39 M16 M10 26 16
K6 180 140j6 50 160 110 160 130 168 200 50h9 50h9
H7 50.5 62 70 128 106 165 3.5 190 310 7.5 254 276 120 40 45 45 40 M16 M10 26 16
K7 195 155h6 55 180 125 180 145 190 226 60h6 60h6
H7 62.0 75 85 161.5 138 185 3.5 212 342 8.0 278 314 125 40 45 45 40 M20 M12 33 19
K8 226 185h6 75 240 165 240 185 235 282 70h6 70h6
H7 72.0 90 100 193 155 215 4.0 265 410 9.0 352 378 145 50 60 60 50 M24 M12 38 19
K9 280 230h6 95 280 185 280 225 285 330 90h6 90h6
H7 92.0 120 120 244 200 265 5.0 315 495 10.0 418 428 180 60 70 70 60 M30 M16 48 26
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
293
10.3.7 S shaft design (hollow shaft with shrink ring), NG housing design (foot +
pitch circle diameter)
1) Machine shaft: The dimension ls must meet or exceed the
specified value.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
294
Dimensions of gear units
Type a0 a4 ∅b b3 b4 b5 b7 B B2 ∅ds ∅ds1 ∅ds2 ∅dss ∅Ds ∅Dsa
K1 115 105 75j6 30 90 30 90 90 106 25h9 25h9
H7 25.5 30 40 80
K2 155 116 82j6 35 115 35 115 115 134 30h9 30h9
H7 30.5 36 45 88
K3 170 132 95j6 40 130 40 130 130 146 35h9 35h9
H7 35.5 44 50 101
K4 200 152 110j6 50 155 50 155 148 173 40h9 40h9
H7 40.5 50 55 114
K5 200 145 110j6 40 140 100 140 160 185 50h9 50h9
H7 50.5 62 65 116
K6 210 180 140j6 50 160 110 160 168 200 50h9 50h9
H7 50.5 62 70 128
K7 241 195 155j6 55 180 125 180 190 226 60h6 60h6
H7 62.0 75 85 161.5
K8 300 226 185j6 75 240 165 240 235 282 70h6 70h6
H7 72.0 90 100 193
K9 360 280 230j6 95 280 185 280 285 330 90h6 90h6
H7 92.0 120 120 244
Type ∅Dss ∅e f h H i2 ls lsa m1 m2 m3 m4 m5 n2 n3 n4 n5 ∅s s4 t4
K1 60 90 3.0 75 175 7.0 149 163 75 20 34 25 29 30 13 140 15 9.0 M8 13
K2 72 100 3.0 88 213 7.0 178 193 88 25 39 30 34 40 20 185 23 11.0 M8 13
K3 80 115 3.0 98 236 7.0 190 206 98 30 39 35 34 45 20 200 23 11.0 M8 13
K4 88 130 3.5 115 265 7.5 220 243 115 40 39 45 34 50 22 230 25 14.0 M10 16
K5 106 130 3.5 190 290 7.5 237 254 130 40 44 45 39 60 27 240 30 18.0 M10 16
K6 106 165 3.5 220 340 7.5 254 276 150 40 45 45 40 65 27 250 30 18.5 M10 16
K7 138 185 3.5 250 380 8.0 278 314 163 40 45 45 40 70 35 290 38 23.0 M12 19
K8 155 215 4.0 310 455 9.0 352 378 190 50 60 60 50 85 41 360 45 27.0 M12 19
K9 200 265 5.0 365 545 10.0 418 428 230 60 70 70 60 95 46 430 50 31.0 M16 26
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
295
10.3.8 S shaft design (hollow shaft with shrink ring), GD housing design (pitch
circle diameter + torque arm bracket)
1) Machine shaft: The dimension ls must meet or exceed the
specified value.
2) Cover (optional)
3) Only for K1 (other sizes on request) − If you brace the gear units without the torque arm brackets provided by the manufacturer for this purpose, the dimensions for ad2 and ad3 must meet the specified value.
10.3 Dimensional drawings 10 K helical bevel gear units
296
Dimensions of gear units
Type ☐a4 ad ad1 ad2 ad3 ad4 ad5 ∅b B B2 ∅dd ∅ds ∅ds1 ∅ds2 ∅dss ∅Dd ∅Ds ∅Dsa
K1 105 6.0 15.0 90 90 15.0 130 75j6 90 106 12H9 25h9 25h9
H7 25.5 30 43 40 80
K2 116 6.5 22.5 100 100 22.5 – 82j6 115 134 16H9 30h9 30h9
H7 30.5 36 45 45 88
K3 132 5.0 25.0 120 120 25.0 – 95j6 130 146 16H9 35h9 35h9
H7 35.5 44 45 50 101
K4 152 9.5 27.5 150 150 27.5 – 110j6 148 173 20H9 40h9 40h9
H7 40.5 50 55 55 114
K5 145 9.5 30.0 250 190 30.0 – 110j6 160 185 20H9 50h9 50h9
H7 50.5 62 58 65 116
K6 180 13.0 30.0 250 180 30.0 – 140j6 168 200 20H9 50h9 50h9
H7 50.5 62 58 70 128
K7 195 15.0 35.0 300 213 35.0 – 155h6 190 226 20H9 60h6 60h6
H7 62.0 75 68 85 161.5
K8 226 17.0 45.0 350 230 45.0 – 185h6 235 282 24H9 70h6 70h6
H7 72.0 90 72 100 193
K9 280 16.0 45.0 450 315 45.0 – 230h6 285 330 24H9 90h6 90h6
H7 92.0 120 75 120 244
Type ∅Dss ∅e f h H i2 ld ld1 ls lsa m1 m2 m3 m4 m5 s4 t4
K1 60 90 3.0 60 160 7.0 24 28 149 163 60 20 34 25 29 M8 13
K2 72 100 3.0 65 190 7.0 32 38 178 193 65 25 39 30 34 M8 13
K3 80 115 3.0 75 213 7.0 32 38 190 206 75 30 39 35 34 M8 13
K4 88 130 3.5 90 240 7.5 40 46 220 243 90 40 39 45 34 M10 16
K5 106 130 3.5 160 260 7.5 40 46 237 254 100 40 44 45 39 M10 16
K6 106 165 3.5 190 310 7.5 40 46 254 276 120 40 45 45 40 M10 16
K7 138 185 3.5 212 342 8.0 64 70 278 314 125 40 45 45 40 M12 19
K8 155 215 4.0 265 410 9.0 102 115 352 378 145 50 60 60 50 M12 19
K9 200 265 5.0 315 495 10.0 102 115 418 428 180 60 70 70 60 M16 26
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
297
10.3.9 S shaft design (hollow shaft with shrink ring), F housing design (round
flange)
1) Machine shaft: The dimension ls must meet or exceed the
specified value.
2) Cover (optional)
10.3 Dimensional drawings 10 K helical bevel gear units
298
Dimensions of gear units
Type ∅a1 ∅b1 b8 B B2 c1 c2 ∅ds ∅ds1 ∅ds2 ∅dss ∅Ds ∅Dsa ∅Dss ∅e1 f1 h H i2 ls lsa m1 m2 m3 m4 m5 ∅s1
K1 160 110j6 70 90 106 10 32.0 25h9 25h9
H7 25.5 30 40 80 60 130 3.5 60 160 25.0 149 163 60 20 34 25 29 9
K2 200 130j6 90 115 134 12 32.0 30h9 30h9
H7 30.5 36 45 88 72 165 3.5 65 190 25.0 178 193 65 25 39 30 34 11
K3 200 130j6 105 130 146 14 38.0 35h9 35h9
H7 35.5 44 50 101 80 165 3.5 75 213 31.0 190 206 75 30 39 35 34 11
K4 250 180j6 120 148 173 15 40.0 40h9 40h9
H7 40.5 50 55 114 88 215 4.0 90 240 32.5 220 243 90 40 39 45 34 14
K5 250 180j6 125 160 185 15 39.5 50h9 50h9
H7 50.5 62 65 116 106 215 4.0 160 260 32.0 237 254 100 40 44 45 39 14
K6 300 230j6 130 168 200 17 36.0 50h9 50h9
H7 50.5 62 70 128 106 265 4.0 190 310 28.5 254 276 120 40 45 45 40 14
K7 350 250h6 145 190 226 18 44.0 60h6 60h6
H7 62.0 75 85 161.5 138 300 5.0 212 342 36.0 278 314 125 40 45 45 40 18
K8 400 300h6 185 235 282 20 45.0 70h6 70h6
H7 72.0 90 100 193 155 350 5.0 265 410 36.0 352 378 145 50 60 60 50 18
K9 450 350h6 225 285 330 23 50.0 90h6 90h6
H7 92.0 120 120 244 200 400 5.0 315 495 40.0 418 428 180 60 70 70 60 18
Dimensions of additional round flanges
Type ∅a1 ∅b1 c1 ∅e1 f1 ∅s1
K1 140 95j6 10 115 3.0 9
K2 160 110j6 12 130 3.5 9
K3 160 110j6 14 130 3.5 9
K3 250 180j6 14 215 4.0 14
K8 350 250h6 18 300 5.0 18
K8 450 350h6 20 400 5.0 18
Type MB23 MB33 MB43
a m n a m n a m n
K102 ∅160 128 36.0 – – – – – –
K202 ∅160 147 46.0 ∅200 149 46.0 – – –
K302 ∅160 167 52.5 ∅200 169 52.5 – – –
K402 ∅160 187 60.0 ∅200 189 60.0 ∅250 192 60.0
K513 ∅160 172 15.0 ∅200 174 15.0 ∅250 177 15.0
K613 ∅160 191 18.0 ∅200 193 18.0 ∅250 196 18.0
K713 – – – ∅200 221 20.0 ∅250 224 20.0
K813 – – – ∅200 247 24.0 ∅250 249 24.0
K913 – – – – – – ∅250 294 25.0
Example dimensions for the motor connection
Type ∅b6 ∅e6 ∅d2max l5 ☐a6 c c6 ∅d6 f6 l7 p10 s6 w7 x2 y2 z7
K_MB23 95F8 115 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 95F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB23 110F8 130 24 72 130 32.0 140 55 4.5 19 59 M8 102.9 58 64 57.5
K_MB33 110F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB33 130F8 165 32 81 155 39.0 161 65 4.5 20 59 M10 115.4 58 64 71.0
K_MB43 130F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
K_MB43 180F8 215 38 96 194 47.5 194 80 5.0 16 59 M12 134.9 58 64 93.5
In the table above, you will find example motor connection dimensions for the MB motor adapter. Note
that when dimension c is lengthened (depending on the motor used), dimensions c6 and l5 are also
lengthened accordingly.
You will find additional motor connection dimensions for the MB motor adapter in our STOBER Configurator
at https://configurator.stoeber.de/en-US/. Here, you can directly download a 3D model of your drive.
10 K helical bevel gear units 10.3 Dimensional drawings
299
10.3.10 S shaft design (hollow shaft with shrink ring), NF housing design (foot +
round flange)
1) Machine shaft: The dimension ls must meet or exceed the
specified value.
2) Cover (optional)
3) Only for K1 (other sizes on request)
10.3 Dimensional drawings 10 K helical bevel gear units
300
