该页无缩略图
powerteam.com 152
Features
Shop Equip.H-FRAME, OPEN-END-ACCESS™ PRESSES
TONNAGE: 25
OPEN-END-ACCESS™ PRESSES
■ Design permits use as both H-Frame and C-Frame
press. Cylinder can be mounted on frame extension to
handle jobs which won’t fit between uprights.
■ Open-end-Access™ press models are also available
with remote control to enable the operator to view work
from all sides with fingertip control of cylinder piston
travel.
■ Off-center pressing loads of full capacity can be applied
across entire width of frame.
■ Press bed height easily adjustable with winch. Bed will
not drop when handle is released.
■ Choice of power sources for rapid cylinder advance:
two-speed hydraulic hand pump, electric/hydraulic or
air/hydraulic.
Model Shown:
SPE2514
Order
No.
Cap. Type
Cyl. Used
Stroke Cyl.
Model
Speed † † †
(in. / min.)
Type of
Pump
Valve
Type
Pump ‡
Model
Prod.
Wt.
(tons) (in.) Advance Pressing (lbs.)
SPA2514 25 Single-Acting 14.25 C2514C 9.8 1.2 Air 2-Way Foot PA6 683
SPM2514 25 Single-Acting 14.25 C2514C 0.49 (in./stroke) 0.03 (in./stroke) Hand Load-Release P159 693
SPX2514 25 Single-Acting 14.25 C2514C - - - - - 620
SPE2514 25 Single-Acting 14.25 C2514C 46.6 3.3 Electric 2-Way †† PE172 665
SPE2514S 25 Single-Acting 14.25 C2514C 52 4 Electric 3-Way † PE213S 759
SPE2514DS 25 Double-Acting 14.25 RD2514 52 4 Electric 4-Way † PE214S 787
SPX2514D 25 Single-Acting 14.25 C2514C - - - - - 742
A B C D * E F G H J K L M Floor
Space
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
58.00 43.00 28.00 3 - 29 6.88 - 43.38 4.50 32.00 5.50 6.50 7.00 2.50 8.00 43 x 28
Lower Bolster
A
E
F
G
B C
H
J
D
K
M
L
* Lateral head movement
† Solenoid valve with 24VAC remote control hand switch.
†† Holds pressure with motor shut-off. Also has an automatic dump setting. Furnished with a 10’ remote motor control.
††† Typical performance based on 100 psi and 10,000 psi pump specifications. Actual speeds may vary under operating conditions.
Pump standard with press. Other Power Team pumps can be substituted. dBA at idle and 10,000 psi: PE172–67/81 dBA; PE21–70; dBA measured at 3 foot distance, all
sides.
‡
Mechanical Puller
Selection Pump Electrical Specifications Optional Cylinders
Pump Series Description
PE17 1/2 hp, 115VAC, 60 cycle, single-phase.
PE21 1 hp, 115VAC, 60 cycle, single-phase.
Both pumps available in 230VAC, 50 cycle, add suffix “-220” to order no.
Adjustable
Open-End-Access™
SP
SERIES
Technical Dimensions
Ordering Information
153 powerteam.com
Features
Shop Equip.
H-FRAME PRESSES
TONNAGE: 55
H-FRAME SHOP PRESS
■ Full off-center pressing at full rated capacity across
width of upper frame without buckling or bending.
■ Maximum “daylight” is 42” x 36”, making positioning of
even bulky work pieces easy.
■ Height of press bed is easily adjusted with winch.
Friction brake prevents bed from dropping and handle
from spinning upon release.
■ Presses with single-acting cylinders offer choice of
2-speed hand operated, electric/hydraulic, or air/
hydraulic pump. Models with double-acting cylinders
have an electric/hydraulic pump.
■ Press models equipped with remote control enable
operator to view work from all sides with fingertip
control of cylinder piston travel.
■ Press can be used horizontally for special applications
with user-supplied support legs.
Model Shown:
SPE5513DS
Order
No.
Cap. Type
Cyl. Used
Stroke Cyl.
Model
Speed † † †
(in. / min.)
Type of
Pump
Valve
Type
Pump ‡
Model
Prod.
Wt.
(tons) (in.) Advance Pressing (lbs.)
SPA556 55 Single-Acting 6.25 C556C 4.5 0.5 Air 2-way foot PA6 804
SPM556 55 Single-Acting 6.25 C556C .23 (in./stroke) .015 (in./stroke) Hand Load-Release P159 814
SPM5513 55 Single-Acting 13.25 C5513C .655 (in./stroke) .026 (in./stroke) Hand 2-Way P460 960
SPE556 55 Single-Acting 6.25 C556C 21.7 1.5 Electric 2-Way †† PE172 836
SPX556 55 Single-Acting 6.25 C556C - - - - - 794
SPE5513 55 Single-Acting 13.25 C5513C 21.7 1.5 Electric 2-Way †† PE172 980
SPX5513 55 Single-Acting 13.25 C5513C - - - - - 938
SPE5513S 55 Single-Acting 13.25 C5513C 24.4 1.9 Electric 3-Way † PE213S 1056
SPE5513D 55 Double-Acting 13.125 RD5513 21.7 1.5 Electric 4-Way PE174 993
SPE5513DS 55 Double-Acting 13.125 RD5513 66.1 5.4 Electric 4-Way † PQ604S 1114
SPX5513D 55 Double-Acting 13.25 RD5513 - - - - - 824
Mechanical Puller
Selection Pump Electrical Specifications Optional Cylinders
Pump Series Description
PE17 * 1/2 hp, 115VAC, 60 cycle, single-phase.
PE21 * 1 hp, 115VAC, 60 cycle, single-phase.
PQ60 * 2 hp, 230VAC, 60 cycle, single-phase.
* Pumps available in 230VAC, 50 cycle, add suffix “-220” to order no.
A B C D * E F G H J L M Floor
Space
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
72.00 48.50 36.00 3.25 - 32.75 6 - 42 6.00 36.00 6.75 8.00 3.00 12.00 48.5 x 36
* Lateral head movement
† Solenoid valve with 24VAC remote control hand switch.
†† Holds pressure with motor shut-off. Also has an automatic dump setting. Furnished with a 10’ remote motor control.
††† Typical performance based on 100 psi and 10,000 psi pump specifications. Actual speeds may vary with operating conditions.
Pump standard with press. Other Power Team pumps can be substituted. dBA at idle and 10,000 psi: PE172—67/81; PE21 Series—70; PQ60—74/76;
measured at 3 foot distance, all sides.
‡
Adjustable
Lower Bolster
A
E
F
G
B C
H
J
D
M
L
Hydraulic gauge and
hydraulic fittings are included with presses.
Note: Frame is shipped assembled.
SP
SERIES
Technical Dimensions
Ordering Information
powerteam.com 154
Features
Shop Equip.H-FRAME SHOP PRESS
■ Cylinder work-head glides across upper frame on
rollers, locks in place for off-center pressing jobs. May
be used horizontally for special pressing applications
with user-supplied supports.
■ Press bed is raised and lowered by winch which locks
in place for insertion of bed retaining pins. Upper
bolster can be lowered 8” for convenient positioning on
repetitive jobs.
■ Generous “daylight” of 42” x 50” accommodates bulky
work pieces, uprights are placed for easy side entry of
bars or shafts for straightening or bending.
■ Choice of single or double-acting cylinder. Hydraulic
pump options include: 2-speed hand pump with large
2-gallon reservoir, PE172 electric/hydraulic pump or
“PQ” series “Quiet” electric/hydraulic pump with low
noise level.
Model Shown:
SPE10013DS
Order
No.
Cap. Type
Cyl. Used
Stroke Cyl.
Model
Speed † † †
(in. / min.)
Type of
Pump
Valve
Type
Pump ‡
Model
Prod.
Wt.
(tons) (in.) Advance Pressing (lbs.)
SPM10010 100 Single-Acting 10.25 C10010C 0.356 (in./stroke) 0.01 (in/stroke) Hand 3-way P460 1698
SPE10010 100 Single-Acting 10.25 C10010C 35 2.9 Electric 3-way PQ603 1795
SPX10010 100 Single-Acting 10.25 C10010C - - - - - 1626
SPE10010R 100 Single-Acting 10.25 C10010C 11 1/2 0.8 Electric 2-way PE172 1690
SPX10013D 100 Double-Acting 13.125 RD10013 - - - - - 1722
SPE10013DS 100 Double-Acting 13.125 RD10013 35 5.8 Electric 4-way † PQ1204S 1886
A B C D * E F G H J L M Floor
Space
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
77.25 64.00 36.00 7 - 43 2 - 42 8.00 50.00 8.00 10.00 3.38 15.00 36 x 78.25
* Lateral head movement
††† Typical performance based on 100 psi and 10,000 psi pump specifications. Actual speeds may vary under operating conditions.
Note: Frame is shipped assembled.
Pump standard with press. Other Power Team pumps can be substituted. dBA at idle and 10,000 psi: PE172—67/81; PQ60—74/76; PQ120—73/78. Measured at 3 foot distance, all
sides.
‡
Lower Bolster
A
E
F
G
B C
H
J
D
M
L
H-FRAME PRESSES
TONNAGE: 100
Adjustable
Mechanical Puller
Selection Pump Electrical Specifications Optional Cylinders
Pump Series Description
PE17 * 1/2 hp, 115VAC, 60 cycle, single-phase.
PQ60 *† 2 hp, 230VAC, 60 cycle, single-phase.
PQ120 ** 3 hp, 460VAC, 60 cycle, three-phase.
* Pumps available in 230VAC, 50 cycle, add suffix “-220” to order no.
† For 115VAC, consult factory.
** Pump available in 220/380VAC, 50 cycle. To order 380VAC, 50 cycle, add suffix “-380”
to order no.
† Solenoid valve with 24VAC remote control hand switch.
Hydraulic gauge and
hydraulic fittings are
included with presses.
SP
SERIES
Technical Dimensions
Ordering Information
155 powerteam.com
Features
Shop Equip.
H-FRAME PRESSES
TONNAGE RANGE: 150-200
H-FRAME SHOP PRESS
■ Standing 7.5 feet tall, these giants handle the really big
jobs.
■ May be used horizontally for special pressing
applications with user-supplied supports.
■ Work-head has wide horizontal travel. Rugged press
frame withstands load of rated capacity across full width
of frame.
■ Winch mechanism provides easy positioning of press
bed, locks in place for insertion of retaining pins.
■ Upper bolster can be lowered 11” for convenient
positioning on repetitive jobs.
■ Uprights are placed for easy side entry of bars or shafts
for straightening or bending.
■ Fast cylinder approach is provided by PQ1204S “Quiet”
electric/hydraulic pump.
■ Remote control hand switch, enables operator to view
work from all sides with fingertip control of cylinder
piston travel.
Model Shown:
SPE20013DS
Hydraulic gauge and hydraulic
fittings are included with presses.
Adjustable
Mechanical Puller
Selection Pump Electrical Specifications Optional Cylinders
Pump Series Description
PQ120 3 hp, 460VAC, 60 cycle, three-phase. Also available in
220/380VAC, 50 cycle, add suffix “-380” to order no.
NOTE: To order press with 230VAC, 60 cycle, single-phase pump, order press less
PQ1204S. Order pump No. PQ604S separately.
SP
SERIES
powerteam.com 156 Shop Equip.Order
No.
Cap. Type
Cyl. Used
Stroke Cyl.
Model
Speed † † †
(in. / min.)
Type of
Pump
Valve
Type
Pump ‡
Model
Prod.
Wt.
(tons) (in.) Advance Pressing (lbs.)
SPX15013D 150 Double-Acting 13.125 RD15013 - - - - - 2851
SPE15013DS 150 Double-Acting 13.125 RD15013 24 3.9 Electric* 4-way ** PQ1204S 3015
SPX20013D 200 Double-Acting 13.125 RD20013 - - - - - 3112
SPE20013DS 200 Double-Acting 13.125 RD20013 18 2.9 Electric* 4-way ** PQ1204S 3276
A B C D * E F G H J L M Floor
Space
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
90.00 71.00 44.00 11 - 39 9 - 43.75 11.00 50.00 12.50 15.00 4.13 18.00 44 x 71
* Lateral head movement
M
L
A
E
G
B
C
H
J
D
F
Lower Bolster
Winch provides easy
positioning of press bed
PQ120 Series pump
provides the pressure
and control
Large footing for a solid
base and stability
Adjustable head
accommodates a
wide array of applications
H-FRAME PRESSES
TONNAGE RANGE: 150-200
††† Typical performance based on 100 psi and 10,000 psi pump specifications. Actual speeds may vary under operating conditions.
Note: Frame is shipped assembled.
* Pre-wired at factory for 460VAC.
** Solenoid valve with 24VAC remote control hand switch.
‡ Pump standard with press. dBA at idle and 10,000 psi: 73/78, measured at 3 foot distance, all sides.
SP
SERIES
Technical Dimensions
Ordering Information
157 powerteam.com
Features
Shop Equip.
H-FRAME ROLL-BED® PRESSES
TONNAGE RANGE: 80-200
H-FRAME ROLL-BED® PRESS
■ The original, patented Roll-Bed® extends out for easy
loading and unloading with a crane or other lifting
device, supporting loads up to 3,000 lbs.
■ Movable work-head glides easily side-to-side for full offcenter load capacity across width of upper frame.
■ “Daylight” is 50.5\" x 60\" for 80 and 100 ton models;
51.25\" x 64\" on 150 and 200 ton presses.
■ Fast approach of double-acting, 13.125\" stroke cylinder
is provided by PQ1204S “Quiet” electric/hydraulic pump
with remote control hand switch. Operator can view
work from all sides with fingertip control of cylinder
piston travel.
■ Adjustable lower bed width for secure balancing and
centering of heavy jobs.
■ Lifting mechanism has a turn crank handle to raise or
lower upper bolster (a heavy-duty 1/2\" drill motor can
replace handle for automatic adjustment). Four locking
pins hold bolster in place for pressing.
Model Shown:
RB10013S
Hydraulic gauge and hydraulic
fittings are included with presses.
Mechanical Puller
Selection Pump Electrical Specifications Optional Cylinders
Pump Series Description
PQ120 3 hp, 460VAC, 60 cycle, three-phase. Available in 220/380VAC,
50 cycle, add suffix “-380” to order no.
NOTE: To order press with a 230VAC, 60 cycle, single-phase pump, order press less
PQ1204S. Order pump No. PQ604S separately.
NOTE: Different voltage and valve options can be obtained by substituting certain PA,
PE or PQ series pumps. Consult the factory.
Adjustable
Roll-bell enables easy loading and unloading of
large gears to simplify the pressing operation.
SP
SERIES
powerteam.com 158 Shop Equip.Note: Frame is shipped assembled.
† Solenoid valve with 24VAC remote control hand switch.
‡ Pump standard with press. dBA at idle and 10,000 psi: PQ120-73/78; measured at 3 foot distance, all sides.
Typical performance based on 100 psi and 10,000 psi pump specifications. Actual speeds may vary with operating conditions. 3,000 lbs. maximum load can be supported on
bed when raised on the rollers.
†††
Order
No.
Cap. Type
Cyl. Used
Stroke Cyl.
Model
Speed † † †
(in. / min.)
Type of
Pump
Valve
Type
Pump ‡
Model
Prod.
Wt.
(tons) (in.) Advance Pressing (lbs.)
RB8013S 80 Double-Acting 13.125 RD8013 46 7.5 Electric 4-way † PQ1204S 2886
RB8013X 80 Double-Acting 13.125 RD8013 - - - - - 2722
RB10013S 100 Double-Acting 13.125 RD10013 35 5.8 Electric 4-way † PQ1204S 2944
RB10013X 100 Double-Acting 13.125 RD10013 - - - - - 2780
RB15013S 150 Double-Acting 13.125 RD15013 24 3.9 Electric 4-way † PQ1204S 4458
RB15013X 150 Double-Acting 13.125 RD15013 - - - - - 4294
RB20013S 200 Double-Acting 13.125 RD20013 18 2.9 Electric 4-way † PQ1204S 4546
RB20013X 200 Double-Acting 13.125 RD20013 - - - - - 4382
Cap. A B C D E F G H J K L M Floor
Space
(Tons) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
80 112.63 64.25 50.50 27.00 12 - 60 14.50 - 36.00 3.00 4.00 - 27.25 8.00 36.50 3.38 15.00 64.25 x 60.50
100 112.63 64.25 50.50 27.00 12 - 60 14.50 - 36.00 3.00 4.00 - 27.25 8.00 36.50 3.38 15.00 64.25 x 60.50
150 123.25 68.25 51.25 30.00 9 - 64 13.88 - 37-88 3.00 4.00 - 27.13 11.00 37.25 4.13 18.00 68.25 x 63.25
200 122.25 68.25 51.25 30.00 9 - 64 15.13 - 36.13 3.00 4.00 - 27.13 11.00 37.25 4.13 18.00 68.25 x 63.25
H-FRAME ROLL-BED® PRESSES
TONNAGE RANGE: 80-200
Width adjusts from 4” to over 27” &
is secured with locking bolts.
Bearings make bed
positioning smooth
and easy.
Cylinder is easily
moved across width
of upper bolster.
Lever lowers bed for
pressing, raises it for
rolling.
Lifting screw and locking
pins make bolster raising
a one-man job.
Lower Bolster
M
L
A
E
C B
G
F
J
D
H
K
Ordering Information
Technical Dimensions
SP
SERIES
159 powerteam.com
Features
Shop Equip.
ALIGNMENT PTAT TOOLS SERIES
ALIGNMENT TOOL RANGE ECCENTRIC SOCKET SIZES MOTOR APPLICATION
Model Quantity Tool Range Socket Quantity Socket Size Stud Hole Power Range AC Motor Frame DC Motor Frame
PTATN-1 2 13/16” to 1-5/8” PTES-1 2 9/16” 3/8”
2-30 HP 182-286TS 182A-288A
PTATN-2 2 7/8” to 2” PTES-2 2 3/4” 1/2”
PTATN-3 2 7/8” to 2-5/8”
PTES-3 2 15/16” 5/8”
20-300 HP 324T-449TS 323A-368A
PTES-4 2 1-1/8” 3/4”
PTATN-4 22 1-1/2” to 4-1/2”
PTES-5 2 1-5/16” 7/8”
300+ HP 5040-505S 403A-448A
PTES-6 2 1-1/2” 1”
PTATN-5 22 1-7/8” to 6-1/8”
PTES-7 2 1-11/16” 1-1/8”
300+ HP 400M-8211S 503A-688A
PTES-8 2 1-7/8” 1-1/4”
PTAT-1104 PTAT-1108
ALIGNMENT TOOL RANGE ECCENTRIC SOCKET SIZES MOTOR APPLICATION
Model Quantity Tool Range Socket Quantity Socket Size Stud Hole Power Range AC Motor Frame DC Motor Frame
PTATN-1 2 21 to 42 mm PTES-1 2 13 mm 8 mm
1-22 kW 80-132 132-180
PTATN-2 2 22 to 51 mm PTES-2 2 17 mm 10 mm
PTATN-3 2 22 to 67 mm
PTES-3 2 19 mm 12 mm
14-224 kW 160-225 200-225
PTES-4 2 24 mm 16 mm
PTATN-4 22 38 to 114 mm
PTES-5 2 30 mm 20 mm
224+ kW 250-355 250-355
PTES-6 2 36 mm 24 mm
PTATN-5 22 48 to 156 mm PTES-7 2 46 mm 30 mm 224+ kW 400 400
PTM-AT1104 PTM-AT1108
Ordering Information
Ordering Information
Easy on easy
off design
Precise, smooth,
easy motor foot
movement
Eccentric socket
ALIGNMENT TOOL RANGE ECCENTRIC SOCKET SIZES MOTOR APPLICATION RANGE
Model Quantity Tool Range Socket Quantity Socket Size Stud Hole Power Range AC Motor Frame DC Motor Frame
PTAT-1108PTAT-1104
PTATN-1 2 13/16\" to 1-5/8\" PTES-1 2 9/16\" 3/8\"
2-30 HP 182-286TS 182A-288A
PTATN-2 2 7/8\" to 2\" PTES-2 2 3/4\" 1/2\"
PTATN-3 2 7/8\" to 2-5/8\"
PTES-3 2 15/16\" 5/8\"
20-300 HP 324T-449TS 323A-368A
PTES-4 2 1-1/8\" 3/4\"
PTATN-4 2 1-1/2\" to 4-1/2\"
PTES-5 2 1-5/16\" 7/8\"
300+ HP 5040-505S 403A-448A
PTES-6 2 1-1/2\" 1\"
PTATN-5 2 1-7/8\" to 6-1/8\"
PTES-7 2 1-11/16\" 1-1/8\"
300+ HP 400M-8211S 503A-688A
PTES-8 2 1-7/8\" 1-1/4\"
ALIGNMENT TOOL RANGE ECCENTRIC SOCKET SIZES MOTOR APPLICATION RANGE
Model Quantity Tool Range Socket Quantity Socket Size Stud Hole Power Range AC Motor Frame DC Motor Frame
PTM-AT1108 PTM-AT1104
PTATN-1 2 21 to 42 mm PTM-ATES-1 2 13 mm 8 mm
1-22 kW 80-132 132-180
PTATN-2 2 22 to 51 mm PTM-ATES-2 2 17 mm 10 mm
PTATN-3 2 22 to 67 mm
PTM-ATES-3 2 19 mm 12 mm
14-224 kW 160-225 200-225
PTM-ATES-4 2 24 mm 16 mm
PTATN-4 2 38 to 114 mm
PTM-ATES-5 2 30 mm 20 mm
224+ kW 250-355 250-355
PTM-ATES-6 2 36 mm 24 mm
PTATN-5 2 48 to 156 mm PTM-ATES-7 2 46 mm 30 mm 224+ kW 400 400
Top View Bottom View Tool Range
Alignment Tool
Eccentric Socket
ALIGN ROTATING MACHINERY WITH PRECISION.
Model Shown:
PTAT-1108, PTAT-1104
Stud Hole: 3/8\" to 1-1/4 or 3/8\" to 3/4\"
Model Shown:
PPTM-AT1108, PTM-AT1104
Stud Hole: 8mm to 30mm or 8mm to 12mm
n Provides the ability to make precise horizontal
adjustments within .001\" (.025 mm)
n Portable sets allow aligning your motors, pumps, and
gear boxes safe, quick, easy
n Eliminates the use of jack bolts, frames and heavy
hammers for alignment
*Kits do not include measurement devices
28 powerteam.com
Features
PT
SERIES
MOTOR ALIGNMENT
SIDE ALIGNMENT TOOL SETS
ALIGN ROTATING MACHINERY WITH PRECISION.
■ Provides the ability to make precise horizontal
adjustments within .001\" (.025 mm).
■ Portable sets allow aligning your motors, pumps, and
gear boxes safe, quick, and easy.
■ Eliminates the use of jack bolts, frames and heavy
hammers for alignment.
Model Shown:
PTAT-1108, PTAT-1104
Stud Hole: 3/8” to 1-1/4 or 3/8” to 3/4”
Model Shown:
PPTM-AT1108, PTM-AT1104
Stud Hole: 8mm to 30mm or 8mm to 12mm
powerteam.com 160
Features
Shop Equip.UNDERCUT
BOLTS PTUB
SERIES
Includes
VIRTUALLY ELIMINATE THE PROBLEM OF BOLT
BINDING WITH MOTOR ALIGNMENT.
■ Innovative precision undercut bolt and washer system
helps reduce downtime and increase productivity
■ Maximum clearance hardened grade-8 bolts along with
through-hardened plated washers help to maintain
perfect alignment.
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU5125 5/16 x 1-1/4 12
PTU5150 5/16 x 1-1/2 12
PTU6125 3/8 x 1-1/4 12
PTU6150 3/8 x 1-1/2 12
PTU8150 1/2 x 1-1/2 12
PTU8175 1/2 x 1-3/4 12
PTU8200 1/2 x 2 12
Hardened Washers (Diameter)
PTUW5 5/16 24
PTUW6 3/8 24
PTUW8 1/2 36
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU9150 9/16 x 1-1/2 12
PTU9200 9/16 x 2 12
PTU9250 9/16 x 2-1/2 12
PTU1020 5/8 x 2 12
PTU1022 5/8 x 2-1/4 12
PTU1025 5/8 x 2-1/2 12
PTU1220 3/4 x 2 12
PTU1222 3/4 x 2-1/4 12
PTU1225 3/4 x 2-1/2 12
Hardened Washers (Diameter)
PTUW9 9/16 36
PTUW10 5/8 36
PTUW12 3/4 36
Mechanical Puller
Selection
• Cylinders • Jacks
• Pumps • Shop Equipment
• Tools • System Components
www.powerteam.com
Learn More - About Power Team Product Optional Cylinders
Model Shown:
PTUB200
Diameter: 5/16\" to 1/2\" VIRTUALLY ELIMINATE THE PROBLEM OF BOLT
BINDING WITH MOTOR ALIGNMENT.
Model Shown:
PTUB300
Diameter: 9/16\" to 3/4\"
Includes
Includes
n Innovative precision undercut bolt and washer system
helps reduce downtime and increase productivity
n Maximum clearance hardened grade-8 bolts along with
through-hardened plated washers help to maintain
perfect alignment
powerteam.com 29
Features
PT
SERIES
MOTOR ALIGNMENT
UNDERCUT BOLT SETS
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU5125 5/16 x 1-1/4 12
PTU5150 5/16 x 1-1/2 12
PTU6125 3/8 x 1-1/4 12
PTU6150 3/8 x 1-1/2 12
PTU8150 1/2 x 1-1/2 12
PTU8175 1/2 x 1-3/4 12
PTU8200 1/2 x 2 12
Hardened Washers (Diameter)
PTUW5 5/16 24
PTUW6 3/8 24
PTUW8 1/2 36
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU9150 9/16 x 1-1/2 12
PTU9200 9/16 x 2 12
PTU9250 9/16 x 2-1/2 12
PTU1020 5/8 x 2 12
PTU1022 5/8 x 2-1/4 12
PTU1025 5/8 x 2-1/2 12
PTU1220 3/4 x 2 12
PTU1222 3/4 x 2-1/4 12
PTU1225 3/4 x 2-1/2 12
Hardened Washers (Diameter)
PTUW9 9/16 36
PTUW10 5/8 36
PTUW12 3/4 36
Mechanical Puller
Selection
• Cylinders • Jacks
• Pumps • Shop Equipment
• Tools • System Components
www.powerteam.com
Learn More - About Power Team Product Optional Cylinders
Model Shown:
PTUB200
Diameter: 5/16\" to 1/2\" VIRTUALLY ELIMINATE THE PROBLEM OF BOLT
BINDING WITH MOTOR ALIGNMENT.
Model Shown:
PTUB300
Diameter: 9/16\" to 3/4\"
Includes
Includes
n Innovative precision undercut bolt and washer system
helps reduce downtime and increase productivity
n Maximum clearance hardened grade-8 bolts along with
through-hardened plated washers help to maintain
perfect alignment
powerteam.com 29
Features
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU5125 5/16 x 1-1/4 12
PTU5150 5/16 x 1-1/2 12
PTU6125 3/8 x 1-1/4 12
PTU6150 3/8 x 1-1/2 12
PTU8150 1/2 x 1-1/2 12
PTU8175 1/2 x 1-3/4 12
PTU8200 1/2 x 2 12
Hardened Washers (Diameter)
PTUW5 5/16 24
PTUW6 3/8 24
PTUW8 1/2 36
Includes
Order No. Size (in.) Quantity
Undercut Bolts (Diameter x Length)
PTU9150 9/16 x 1-1/2 12
PTU9200 9/16 x 2 12
PTU9250 9/16 x 2-1/2 12
PTU1020 5/8 x 2 12
PTU1022 5/8 x 2-1/4 12
PTU1025 5/8 x 2-1/2 12
PTU1220 3/4 x 2 12
PTU1222 3/4 x 2-1/4 12
PTU1225 3/4 x 2-1/2 12
Hardened Washers (Diameter)
PTUW5 9/16 36
PTUW6 5/8 36
PTUW8 3/4 36
Model Shown:
PTUB200
Stud Hole: 3/8” to 1-1/4 or 3/8” to 3/4”
Model Shown:
PTUB300
Diameter: 9/16” to 3/4”
161 powerteam.com
Features
MOBILE FLOOR CRANES
LBS. RANGE: 2,200 - 4,400
Mobile Floor Cranes
■ Adjustable legs spread to clear obstacles (telescoping
boom for extra reach)
■ Rugged construction, reliable hydraulics.
■ Boom collapses completely and legs fold for compact
space-saving fold-away storage
■ 2-speed hydraulic hand pump provides fast boom travel
and precise operator controlled descent.
■ Roller bearing wheels and a steering dolly provide ease
of mobility. Lifting chain is included.
■ U.S. Patent No. 3,367,512
Model Shown:
FC2200
Pump has a
safety relief valve.
Load-lowering valve
provides controlled descent. Crane is locked
in position when
wheels are lifted.
Piston rod
is ground
and hard
chrome
plated.
Adjustable
Legs
Description FC2200 FC4400
A Max. boom height (ret.) 107\" 111\"
B Max. boom height (ext.) 117\" 122\"
C Overall height, boom horizontal 80\" 82\"
D Overall length 83\" 89\"
E Min. throat width 24\" 25\"
F Inside leg length 54\" 57.5\"
G Eff. boom reach (ret.) 33\" 35.5\"
H Eff. boom reach (ext.) 48\" 50.5\"
J Inside leg width 24\" - 36\" - 48\"
(3-Position)
26\" - 40\" - 52.5\"
(3-Position)
K Leg height 8\" 9.5\"
L Dolly wheel diameter 5\" 5\"
M Wheel diameter 6\" 8\"
N Caster diameter 6\" 6\"
Floor space, folded 27\" x 38\" 31\" x 42\"
Height, folded 79\" 86\"
Cap. boom ret. (lbs.) 2,200 4,400
Cap. boom ext. (lbs.) 1,650 3,300
Order No. Description
FC2200 2,200 lbs. cap. crane with fold-away feature, adj. leg spread, lifting chain and 2-speed hand pump. Wt., 454 lbs.
FC4400 4 ,400 lbs. cap. crane with fold-away feature, adj. leg spread, lifting chain and 2-speed hand pump. Wt., 646 lbs.
FC
SERIES
Technical Dimensions
Ordering Information
Shop Equip.
powerteam.com 162
Features
HYDRAULIC BENCH VISE
TONNAGE: 5 PT
SERIES
Kit Components PTPHV859SPX PTPHV859ASPX
5T Hydraulic Vise PTPHV859 PTPHV859
Hold-Ets Magnetic Clips PTHE3 PTHE3
Air/Hydraulic Foot Pump - PA6
Gauge 9040 9040
Gauge Adapter 9670 9670
Hose 9758 9758
Female Coupler 9796 9796
Male Coupler 9798 9798
Model Shown:
PTPHV859ASPX
Model Shown:
PTHE3
HANDS-FREE HYDRAULIC BENCH VISE WITH
COMBINATION 10,000 PSI (690 BAR) FOOT PUMP,
PROVIDES 5 TONS OF CLAMPING FORCE.
*Air supply is required when using a hydraulic pump
Includes
n Includes an air control valve for variable speed and
safety
n Vise operates vertical or horizontal configurations for
project flexibility
n Vise jaws open up to 8\" (203 mm) for large holding
requirements
n Magnetically hold sockets for assembling and
disassembling universal joints
n Provides 3\" (76 mm) of rigid aluminum construction and
superior magnetic locking power to hold screws, rings,
c-clips, and springs
n Makes any job a one-man operation with superior
strength to hold 5.5 lbs (2.49 kg) vertically and 2.75 lbs
(1.24 kg) pounds horizontally
n Can be used as a jaw liner for non-marking material and
hold threaded objects rigid without damage to threads
Features
Shop Equip.MAGNETIC VISE CLIPS
163 JACKS
SELECT FROM A WIDE RANGE OF LIFTING JACK
PRODUCTS AND MAINTENANCE SETS TO COMPLETE
YOUR SYSTEM REQUIREMENTS
• A hydraulic jack is a powerful lifting or pushing tool designed
to provide effective lift over greater distances than a basic
mechanical jack.
• Turnkey maintenance sets offer matched hydraulic system
components, adapters and hydraulic spreader, contained in
a rugged carrying and storage case.
• Specialty hydraulic jacks support post tension, low height or
clearance applications.
• Portable high tonnage jacks are totally self-contained, their
modular design allows you to change lifting modules to suit
your tonnage or height requirements.
164
Section /
Series Page Content Tonnage
Range Pages
Introduction Choosing the Right Jack — 165-166
9
Sidewinder Mini Jacks 5 - 20 167
Low Profile Bottle Jacks 12, 20 &
30 168
Portable Hydraulic Power Bottle Jacks 2 - 110 169
Telescoping Bottle Jacks 6-13 170
J Economy Toe Jacks 5.5, 11 &
27.5 171
M Maintenance Sets 2.5 & 10 172
RJ Portable Railroad Edition Jacks and
Accessories 100 173-174
JE / JA Portable High Tonnage Railroad Jacks
and Accessories
55, 100,
150 175-176
SK 10 and 25 Ton Start-Up Kits 10 & 25 177-178
SJ Post-Tension and Stressing Jacks and
Accessories 20 & 30 179-180
INDEX
JACK OVERVIEW
165 powerteam.com
Jacks
1. What do you need to lift?
Depending on the vehicle or machine you need
to lift, you will require appropriate equipment. You
don’t lift a 20 ton truck with the same equipment
you would use to lift a 2 ton vehicle.
To choose the right fit, first look at the hydraulic
jack capacity. Today, on the market, you can
find various sizes of hydraulic jacks, with a lifting
capacity going from 1 ton to 300 tons, and even
more.
2. What is the free space available?
The best jack in the world is useless if you can’t
place it under the load. Nowadays, application start
height is getting lower and lower, requiring a more
compact equipment.
Ground clearance is an important parameter to
consider, you need to be able to place the jack
without damaging the load.
3. What is the maximum lifting height you
would need?
To make the best choice, compare the number
of strokes and maximum height of each hydraulic
jack.
In addition, ask the how many extensions are
available with the hydraulic jack. Some of the
equipment has 1 or 2 additional extensions,
which will cover more applications with the same
equipment.
INFO SECTION
CHOOSING THE RIGHT JACK
Step 1: Select the style jack that best suits the application and your intended lift.
Step 2: How much clearance, or open space, is available? What is the minimum height?
Step 3: How much lift, or extension, is required for the load? What is the tonnage needed?
SELECTING THE RIGHT JACK:
JACK SIZING CONSIDERATIONS:
Hydraulic Bottle Jacks
Choose from this complete line of premium quality, standard bottle
jacks. Ideal for use in any number of industrial lifting and pushing
applications.
Tonnage Range: 2-110
JACK SERIES:
powerteam.com 166 JacksINFO SECTION
CHOOSING THE RIGHT JACK
Maintenance Sets
Matched hydraulic system components, adapters and a hydraulic
spreader, contained in a rugged carrying and storage case. Portable
sets are ideal for pushing, pulling, lifting, straightening, or clamping at
remote job sites.
Types: Manual or electric drive maintenance sets
Tonnage Range 10 - 25
Portable High Tonnage Jacks
Totally self-contained, modular design allows you to change lifting
modules to suit your tonnage or height requirements.
Tonnage Range: 55 - 300
167 powerteam.com
Jacks
Features
Ordering Information
Model Shown:
9210A, 9220A, 9105A, 9205A
SIDEWINDER JACKS, MINI JACKS
TONNAGE RANGE: 5 - 20
Order
Number
Cap. Stroke Retracted
Height
Max.
Height
No. Pump
Strokes to
Ext. Piston
Saddle
Dia.
Base
Size
Dia.
Pump
Handle
Length
Handle Effort
at Rated Cap.
Carry
Handle
Prod.
Wt.
(tons) (in.) (in.) (in.) (in.) (in.) (in.) (lbs.) (lbs.)
9105A 5 0.75 2.50 3.38 30 1.14 2,91 9.44 57 No 4.20
9205A 5 1.50 3.50 5.13 38 1.14 2.91 9.44 57 No 5.30
9210A 10 1.19 4.75 5.88 36 1.66 4.33 17.33 62 No 12.10
9220A 20 1.19 5.13 6.31 46 2.08 4.72 23.81 77 No 17.60
■ Retracted height of just 2.56\" for the smallest jack and
5.13\" for the 20 ton, allows you to slip this jack into the
narrowest of crevices.
■ Jacks operate either horizontally or vertically. Handles
function in line with base for easier use in confined
spaces.
■ The perfect addition to any toolbox, this remarkable
little jack has multiple uses that are limited only by your
imagination. Use it as a jack, or a spreader. Use it to
turn your mechanical gear puller (note: puller capacity
must match jack capacity) into a hydraulic puller.
■ High strength piston and pump linkage for long life.
■ All models include over-travel protection.
■ Lever Bar included on all models.
■ All jacks meet ASME B30.1 standards and carry the
Power Team PowerThon™ Lifetime Warranty.
COMPACT SIDEWINDER MINI JACK FITS IN YOUR
PALM AND DELIVERS 5, 10 & 20 TONS OF LIFTING
FORCE.
9
SERIES
9105A Sidewinder jack is the ideal choice for straightening this
crushed box steel .
powerteam.com 168 JacksFeatures
■ All the quality, features and lifting capacity of the
standard jacks in short form. The 12 ton and 20 ton
models feature screw extensions for added versatility.
■ All jacks operate both vertically and horizontally for
use in a variety of lifting, pushing and spreading
applications.
■ Large base area for increased strength and stability
during lifting.
■ High strength piston and pump linkage for long life.
■ All models include over-travel protection.
■ Lever Bar included on all models.
■ All jacks meet ASME B30.1 standards and carry the
Power Team PowerThon™ Lifetime Warranty.
THE RIGHT CHOICE FOR THOSE LOWER
CLEARANCE JOBS OR APPLICATIONS
Model Shown:
9012A, 9020A, 9130A
BOTTLE JACKS, LOW PROFILE
TONNAGE RANGE: 12, 20 & 30
Ordering Information
Order
Number
Cap. Stroke Retracted
Height
Length of
Screw Ext.
Height with
Screw Ext.
No. Pump
Strokes to
Ext. Piston ‡
Saddle
Dia.
Base
Size
Pump
Handle
Length
Handle Effort
at Rated Cap.
Carry
Handle
Prod.
Wt.
(tons) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lbs.) (lbs.)
9012A 12 3.75 6.75 3 13.50 26 1.88 6.50 x 4.19 23.81 60 Yes 14.00
9020A 20 3.38 7.13 1.56 12.00 22 2.00 7.19 x 5.06 31.50 70 Yes 22.22
9130A 30 3.13 7.13 — 10.25 35 2.38 7.56 x 5.56 39.38 50 Yes 30.20
‡ 2 Speed: Rapid advance≈40 strokes; Lift mode≈160 strokes.
9
SERIES
9130A Low Profile Hydraulic Bottle Jack provides the lifting
capacity and low height for this underground mining application.
169 powerteam.com
Jacks
Features
† Comes with a Beveled Base.
‡2 Speed: Rapid advance≈40 strokes; Lift mode≈160 strokes.
Ordering Information
Model Shown:
9030A, 9008A, 9112A
BOTTLE JACKS, PORTABLE HYDRAULIC POWER
TONNAGE RANGE: 2 - 110
Order
Number
Cap. Stroke Retracted
Height
Min.
Length of
Screw Ext.
Height with
Screw Ext.
No. Pump
Strokes to
Ext. Piston
Saddle
Dia.
Base
Size
Pump
Handle
Length
Handle
Effort at
Rated Cap.
Carry
Handle
Prod.
Wt.
(tons) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lbs.) (lbs.)
9002A 2 4.50 7.13 1.94 13.56 5 1.00 4.69 x 2.56 12.25 75 No 4.80
9003A 3 4.50 7.50 2.38 14.38 10 1.13 4.50 x 2.84 19.25 45 No 5.80
9005A 5 4.75 7.88 2.75 15.38 12 1.38 5.19 x 3.00 21.44 55 No 8.00
9008A 8 4.75 7.88 2.75 15.38 18 1.50 6.00 x 3.50 23.81 75 No 12.1
9112A 12 5.88 9.50 3.13 18.50 26 1.88 6.50 x 4.19 23.81 60 Yes 17.50
9015B 15 6.13 9.06 4.50 19.88 27 2.38 5.13 x 5.50 † 27.56 90 No 18.30
9120A 20 6.25 10.63 3.63 20.50 22 2.00 7.19 x 5.06 31.50 70 Yes 28.50
9022B 22 6.13 9.44 4.31 20.50 36 2.38 6.50 x 6.31 † 27.56 90 Yes 23.60
9030A 30 6.25 11.00 — 17.25 35 2.38 7.56 x 5.56 39.38 50 Yes 41.20
9033B 33 5.63 9.44 4.19 19.75 56 2.56 7.25 x 6.94 † 27.56 88 Yes 32.00
9050A 50 6.75 12.00 — 18.75 36 3.00 9.31 x 7.38 39.38 85 Yes 78.00
9110B 110 6.13 11.81 — 17.94 40/160 ‡ 4.38 13.38 x 11.44 27.56 79 Yes 154.30
■ Choose from this complete line of premium quality
bottle jacks. Ideal for use in any number of industrial
lifting and pushing applications.
■ The 9110B, 9015B, 9022B and 9033B feature a
beveled base which allows the jack to “follow” the load,
reducing the chance of dangerous side-loading.
■ Jacks feature a screw extension for quicker setup.
■ High strength piston and pump linkage for long life.
■ All models include over-travel protection.
■ Lever Bar included on all models. All jacks can be used
in the vertical, angled or horizontal positions.
■ Serrated or contoured saddles help stabilize the load
for a safer lift.
■ 110 ton jack features dual pumps for time-saving twospeed operation.
■ All jacks meet ASME B30.1 standards and carry the
Power Team PowerThon™ Lifetime Warranty.
IDEAL FOR INDUSTRIAL LIFTING AND PUSHING
APPLICATIONS FOR MRO
9
SERIES
powerteam.com 170 JacksFeatures Model Shown:
9006X, 9011X, 9013X
BOTTLE JACKS, TELESCOPING
TONNAGE RANGE: 6-13
Ordering Information
Order
Number
Cap. Stroke Retracted
Height
Length of
Screw Ext.
Height with
Screw Ext.
No. Pump
Strokes to
Ext. Piston
Saddle
Dia.
Base Size
Beveled
Base
Pump
Handle
Length
Handle Effort
at Rated Cap.
Carry
Handle
Prod.
Wt.
(tons) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lbs.) (lbs.)
9006X 6 12.00 8.50 — 20.50 14 1.75 4.75 x 5.25 27.56 79 No 14.00
9011X 11 10.30 7.88 2.69 20.88 25 1.63 6.31 x 6.50 27.56 88 No 19.50
9013X 13 10.00 9.06 3.31 22.44 35 1.88 6.94 x 7.31 27.56 79 Yes 25.00
■ Telescoping jacks offer all of the quality features and
capabilities of the standard bottle jack line with a bonus.
The super-long stroke of these jacks saves time and
effort by eliminating the need to lift or crib. In most
applications, the user can place the jack once and
complete the lift.
■ The 9006X, 9011X and 9013X all feature a unique
beveled base that allows the jack to “follow” the load
laterally as it is raised, greatly reducing side-loading of
the piston.
■ High strength piston and pump linkage for long life.
■ All models include over-travel protection.
■ Lever Bar included on all models.
■ All jacks meet ASME B30.1 standards and carry the
Power Team PowerThon™ Lifetime Warranty.
THE RIGHT CHOICE FOR THOSE LOWER HEIGHT
APPLICATIONS FOR MRO.
9
SERIES
171 powerteam.com
Jacks
Features
Ordering Information
Technical Dimensions
Model Shown:
J24T, J55T, J106T
TOE JACKS, ECONOMY
TONNAGE RANGE: 2.5 & 10
Order
Number
Cap. Max. Lift
Stroke
Strokes to Ext. Piston Handle
Effort at Max. Load
Carry
Handle
Prod.
Wt.
(tons) (in.) (1 in.) (lbs.) (lbs.)
J24T 2 4.75 14 42.00 Yes 18.30
J55T 5 4.88 22 60.00 Yes 53.00
J106T 10 5.88 31 73.00 Yes 83.80
Order
Number
Ret. Ext. Ret. Ext.
A B C D E F
(in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.)
J24T 0.63 5.50 9.25 14.00 1.88 7.13 2.00 4.94
J55T 1.00 5.88 11.50 16.38 1.88 10.13 3.00 7.25
J106T 1.25 7.13 12.88 18.75 2.50 11.50 3.94 9.50
■ These bottle jack-style toe jacks are loaded with many
of the same features as our standard bottle jacks, but
the toe-lift feature and swiveling pump handle socket
make them ideal for machinery lifting and positioning.
■ An internal pressure relief provides added safety by
limiting the jack’s lifting capability to the capacity of the
toe.
■ Spring return is an added feature on the J55T and
J106T jacks.
■ Swiveling pump handle assembly available on the
5 and 10 ton models. The swiveling jack assembly
allows you to access and pump the unit from numerous
positions.
■ High strength piston and pump linkage for long life.
■ All models include over-travel protection.
■ Lever Bar included on all models.
■ All jacks meet ASME B30.1 standards and carry the
Power Team PowerThon™ Lifetime Warranty.
LOW HEIGHT INDUSTRIAL LIFTING AND PUSHING
APPLICATIONS.
J
SERIES
powerteam.com 172 JacksFeatures
NOTE:Actual storage box may differ from photo.
MAINTENANCE SETS, HYDRAULIC SYSTEM
TONNAGE RANGE: 10 IM
SERIES
■ Matched hydraulic system components, adapters and
hydraulic spreader, contained in a rugged carrying and
storage case.
■ Portable sets are ideal for pushing, pulling, lifting,
straightening, or clamping at remote job sites.
■ Cylinders in set are rated at 10 tons at 10,000 psi. Set
components are designed for full rated capacity of
cylinders.
■ IM10B comes with a battery powered pump, while the
IM10E comes with an electric pump. Both come with
two 10T cylinders. The IM10P/IM10L each come with a
hand pump and one 10T cylinder.
Order No. IM10B IM10E
CONTENTS OF SET Items Included
below
Items Included
below
Hydraulic spreader HS2000 HS2000
Hand pump (electric) PB102-1 PE102
Hydraulic gauge (10,000 psi) 9041 9041
Tee adapter 9670 9670
Hose & coupler assembly 9754 9754
90° V base 25395 25395
Threaded coupler 25664 25664
Serrated saddle 31772 31772
Flat base 32325 32325
Extension rod - 5” length 350897 350897
Extension rod - 10” length 38909 38909
Extension rod - 18” length 350898 350898
Cylinder support base 420062 420062
Cylinder, 10 ton, 6.13 stroke C106CBT C106CBT
Cylinder, 10 ton, 10.13 stroke C1010CBT C1010CBT
Storage box 350722 350722
Prod. Weight (lbs.) 106.00 106.00
Order No. IM10H IM10L
CONTENTS OF SET Items Included
Below
Items Included
Below
Hydraulic spreader HS2000 HS2000
Hand pump P59 P59L
Hydraulic gauge (10,000 psi) 9041 9041
Tee adapter 9670 9670
Hose & coupler assembly 9754 9754
90° V base 25395 25395
Threaded coupler 25664 25664
Serrated saddle 31772 31772
Flat base 32325 32325
Extension rod - 5” length 350897 350897
Extension rod - 10” length 38909 32890
Extension rod - 18” length 350898 350898
Cylinder support base 420062 420062
Cylinder, 10 ton, 6.13 stroke C106CBT C106CBT
Storage box 350722 350722
Prod. Weight (lbs.) 89.00 81.00
Ordering Information
Model Shown:
IM10E, IM10H
Mechanical Puller
Selection Application Flexibility Optional Cylinders
TURNKEY, EXTREMELY VERSATILE MECHANICS
MAINTENANCE KIT FITS MANY APPLICATIONS.
173 powerteam.com
Jacks
Features
* C models include RJ-CB-S crib set
** 24”– E models include RJ-EXT-S1 set
†Shipping weights 37”– E version includes RJ-EXT-S set
Ordering Information
Technical Specifications
Model Shown:
RJ100T24E
PORTABLE, RAILROAD EDITION
TONNAGE RANGE: 100
Order
Number
Description Stroke Retracted Height
A
(in.) (1 in.)
RJ100T24E Jack, 100 Ton RR 24\" Ret, Elect 14 24
RJ100T37E Jack, 100 Ton RR 37\" Ret, Elect 27 37
RJ100T24A Jack, 100 Ton RR 24\" Ret Air 14 24
RJ100T37A Jack, 100 Ton RR 37\" Ret Air 27 37
RJ100T24A-C* Jack, 100 Ton RR 24\" Ret Air w/Crib Block 14 24
RJ100T24E-C* Jack, 100 Ton RR 24\" Ret Elect w/Crib Block 14 24
RJ100T37A-C* Jack, 100 Ton RR 37\" Ret Air w/Crib Block 27 37
RJ100T37E-C* Jack, 100 Ton RR 37\" Ret Elect w/Crib Block 27 37
RJ100T24A-E** Jack, 100 Ton RR 24\" Ret Air w/Ext 14 24
RJ100T24E-E** Jack, 100 Ton RR 24\" Ret Elect w/Ext 14 24
RJ100T37A-E† Jack, 100 Ton RR 37\" Ret Air w/Ext 27 37
RJ100T37E-E† Jack, 100 Ton RR 37\" Ret Elect w/Ext 27 37
Type of
Pump
Low Pressure Pump High Pressure Pump Current Draw
at Max. Internal
Relief Settings
Unload
Pressure
Internal
Relief
Pressure
Tank Valving
Flow Pressure Flow Pressure
(cu. in. / min.) (psi.) (cu. in. / min.) (psi.) (amps) (psi.) (psi.) (gal.)
Electric 440
440
48
10,000
25
540 - 780 10,000 2 4-Way / 3-Pos.
Air Tandem Center Manual 330 30 NA
■ Wide base cylinder design for stability.
■ Double-acting cylinder with locking collar.
■ The bottom of the cylinder is a bolted joint, using the
base plate as part of the cylinder. This will allow for
service of even the oldest or most abused jacks.
■ Cribbing storage rack location is such that it allows
easy access during cribbing placement and removal.
■ Jack has a 20 ft. remote pendant for user safety and
control.
■ Easy to maneuver, large tires and small footprint make
it easy to get into tight spaces.
■ Adjustable handle, allows the user to easily to position
the jack under loads.
HEAVY-DUTY SELF-CONTAINED INDUSTRIAL
5 position LIFTING JACK FOR RAIL MAINTENANCE.
adjustable
handle.
Aluminum Cribbing blocks
storage rack.
Aluminum
extensions.
16\" foam-filled tires.
Counter-balance valve
provides
controlled lowering of
jack. Cylinder bolted
(8 x) to base plate (2.5\"
Thick)
Wide base
Cylinder.
20 Ft Remote for
user safety and
control.
55.24
28.00 26.72
RJ
SERIES
powerteam.com 174 JacksPORTABLE, RAILROAD EDITION
ACCESSORIES
EXTENSIONS
Order No. Description
RJ-EXT18 Assembly, Extension 18 in. 100 Ton RR Jack
RJ-EXT14 Assembly, Extension 14 in. 100 Ton RR Jack
RJ-EXT11 Assembly, Extension 11 in. 100 Ton RR Jack
RJ-EXT9 Assembly, Extension 9 in. 100 Ton RR Jack
RJ-EXT7 Assembly, Extension 7 in. 100 Ton RR Jack
RJ-EXT5 Assembly, Extension 5 in. 100 Ton RR Jack
RJ-EXT-S Set, Extensions 100 Ton RR Jack 5, 7, 9
RJ-EXT-S1 Set, Extensions 100 Ton RR Jack 5, 11, 18
SPACERS
Order No. Description
RJ-SP-1 Spacer, 1 in.
RJ-SP-2 Spacer, 2 in.
RJ-SP-3 Spacer, 3 in.
RJ-SP-S Spacer Set 100 ton RR Jack 1, 2, 3
CRIBBING BLOCKS
Order No. Description
RJ-CB10 Assembly, Crib Block 10 in. 100 Ton RR Jack
RJ-CB5 Assembly, Crib Block 5 in. 100 Ton RR Jack
RJ-CB3 Assembly, Crib Block 3 in. 100 Ton RR Jack
RJ-CB1 Assembly, Crib Block 1 in. 100 Ton RR Jack
RJ-CB-S Set, Crib Blocks 100 Ton RR Jack 1, 3, 5, 10
SWIVEL CAPS
Order No. Description
RJ-SC-1 Assembly, Swivel Cap 100 Ton RR Jack
RJ-SC-2 Assembly, Swivel Cap 100 Ton RR Jack Long
RJ
SERIES
175 powerteam.com
Jacks
Features
JE/JA
SERIES
CRIBBING BLOCK SETS - INCLUDES ONE JACK MODULE EXTENSION
PORTABLE HIGH TONNAGE JACKS
TONNAGE RANGE: 55, 100, 150, 200 & 300
■ Modular design allows you to change lifting modules to
suit your tonnage or height requirements.
■ Select the collapsed height to fit your most frequent
application and add jacking modules to suit your needs.
■ Exclusive load control system provides positive,
chatter-free control when lowering the load.
■ Remote operation for maximum operator safety and
control, motor or/an valve options.
■ Easy to maneuver with large tires and small “footprint”
make it easy to scoot into the tightest quarters.
■ Adjustable, heavy-duty handle makes this jack easy to
move, position under vehicles.
■ Shielded and sheltered hydraulic lines for safer, longer,
trouble-free service.
PORTABLE AND COMPACT, IDEAL FOR
LOCOMOTIVE/RAIL CAR, MINING AND HEAVY
EQUIPMENT MAINTENANCE.
Air pump
and cart module.
Electric pump
and cart module.
• Convert jack module into
stable mechanical cribbing
device.
• Increases total stack height
up to 20.50\".
Order
Number
No.
in Set
Cap. A B C Jack Module
Ext.
Total Stack
Height
Prod.
Weight.
(ton) (in.) (in.) (in.) (in.) (in.) (lbs.)
CBS55 1 55 1.50 1.75 5.50 6.81 20.31 36.00 4 3.00 3.25
CBS100 1 100 1.50 1.75 7.38 7.00 20.50 68.00 4 3.00 3.25
CBS150 1 150 1.50 1.75 8.75 6.63 20.13 85.00 4 3.00 3.25
CBS200 1 200 1.50 1.75 10.00 6.63 20.13 105.00 4 3.00 3.25
JACK MODULE EXTENSION
Order
Number
Cap. A B C D E F G H Prod.
Wt.
(tons) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lbs.)
58945 55 8.81 6.81 5.00 2.63 1 11/18-8UNC 2.50 2.63 3.63 21.00
58943 100 9.00 7.00 6.88 3.88 2 3/4-12UNC 3.75 3.88 3.75 40.00
58944 150 8.63 6.63 8.00 4.50 3 1/4-8UNC 4.38 4.50 3.50 50.00
Model Shown:
JEM5526,PMA55S,PME55S
powerteam.com 176 JacksJE/JA
SERIES
PORTABLE HIGH TONNAGE JACKS
TONNAGE RANGE: 55, 100 , 150, 200& 300
Ordering Information - Complete with Pump and Jack Modules, Fully Assembled
Technical Dimensions
Order
Number
Cap. Retracted
Height
Extended
Height
Stroke Pump
Type
Power
Required
Valve
Type
Remote
Control
(tons) (in.) (in.) (in.)
JEM5526 55 26.00 39.13 13.13 Electric 25 amps Manual Motor Only
JAM10033 100 33.00 46.13 13.13 Air 50 CFM @ 80 ps Manual Motor Only
JAR10033 100 33.00 46.13 13.13 Air 50 CFM @ 80 psi Air Pilot Motor & Valve
JEM15026 150 26.00 39.13 13.13 Electric 25 amps Manual Motor Only
JAM15033 150 33.00 46.13 13.13 Air 50 CFM @ 80 psi Manual Motor Only
Model
Series A B C D E F G * H
(in.) (in.) (in.) (in.) (in.) (in.) (deg.) (in.)
PMA 57.88 29.62 53.25 30.00 34.31 23.38 70° 16” Tire Dia. PME
Patented load control system
for chatter-free lowering of
loads.
Electric or air hydraulic
systems available.
Shielded
hydraulic
lines for
greater safety.
Adjustable
handle for
max. control.
20 ft. remote
control.
55, 100, 150, 200,
and 300 ton capacities
Large urethane-filled tires
provide durability and easy
maneuverability.
Steel base
not prone to
cracking like cast.
Modular design allows for
quick interchange
of pump with other modules.
26\"
Jack Module
33\"
Jack Module
45\"
Jack Module
*Total range with varying degree increments.
JM Model PM Model
*Retracted/
Extended
Height
14.63\" 11.00\"
Mechanical Puller
Selection Pump Module, include Remote Pendant Optional Cylinders
Pump Motor Only Motor & Valve
Air PMA55 PMA55S
Electric PME55 PME55S
*Collapsed height; 28” and stroke 13.13”
†Stroke 13.13”.
Mechanical Puller
Selection
Jack Modules Optional Cylinders
Tonnage Cylinder
Stroke
Collapsed Height
26\" 33\" 45\"
55 13.13 JM25 JM35 JM45
100 13.13 JM210 JM310 JM410
150 18.13 JM215 † JM315 JM415
200 18.13 JM220 * JM320 JM420
300 13.13 Contact Factory
Jack modules easily separate from the pump and cart
module.
JACK MODULES
Pump and cart modules contain hydraulic pump, cart, remote
control and all hoses and fittings required to connect to a jack
module.
PUMP & CART MODULES
Jacks
177 powerteam.com
Jacks
Features
Order No Kit Contents
SK10T SK10TE Hand Pump Usable Oil Cap.
(in3 .)
Volume Per Stroke Low /
High Press.
(in3
.)
Weight
(lbs.)
X X P19L 27 0.25 / 0.05 5.10
Gauge Type Primary Units Face Diameter
(in.)
X 9040 analog psi 2.50
Hose Length
(ft.)
Burst Rating I.D.
(in.)
X 9754 6.00 2:1 1/4
Cylinders Capacity*
Short Tons
Stroke
(in.)
Collapsed Height
(in.)
X X C106C 10 6.00 9.75
X X RSS101 10 1.00 3.50
X X RH123 12 3.00 7.25
X X RLS100 10 0.44 1.75
Spreader Min. Clearance
(in.)
Max Spread
(in.)
Weight
(lbs.)
X X HS2000 0.56 4.00 4.80
Case Material L x H x W
(in).
Weight w/o Product
(lbs.)
X X 2008632 Heavy-Duty Plastic 31.5 x 20.5 x 11.5 12.70
■ 10 ton Start-Up Kit covers a range of lifting, shifting,
and positioning needs
■ Broad range of cylinder types and strokes to fit many
applications
■ Neatly packaged in a durable, molded storage case
to securely house your equipment and is ready to use
upon opening
■ SK10TE kit is CE Compliant
Model Shown:
SK10T
Ordering Information
Values shown in short tons (2,000 lb). To convert to long tons, multiply by
0.893. To convert to metric tons, multiply by 0.907. *
VERSATILE 10 TON MAINTENANCE KIT
CONVENIENTLY PACKAGED IN A BOX.
SK
SERIES
Mechanical Puller
Selection Storage Case Dimensions Optional Cylinders
Plastic Molded Case, 31.5”(L) x 20.5”(H) x 11.5”(W).
L
H
W
STARTUP KIT
TONNAGE RANGE: 10
powerteam.com 178 JacksFeatures Model Shown:
SK25T
■ 25 Ton Start-Up Kit covers a range of lifting, shifting,
and positioning needs
■ Broad range of cylinder types and strokes to fit many
applications
■ SK25TE kit is CE Compliant
Storage cases are not included with the 25 ton startup kits, they
must be ordered separately.
NOTE:
Order No Kit Contents
SK25T SK25TE Hand Pump Usable Oil Cap.
(in3 .)
Volume Per Stroke Low / High Press.
(in3
.)
Weight
(lbs.)
X X P59L 66 0.72 / 0.15 8.90
Gauge Type Primary Units Face Diameter
(in.)
X 9040 analog psi 2.50
Hose Length
(ft.)
Burst Rating I.D.
(in.)
X 9754 6.00 2:1 1/4
Cylinders Capacity*
Short Tons
Stroke
(in.)
Collapsed Height
(in.)
X X C256C 25 6.00 10.75
X X RSS302 30 2.00 4.63
X X RH302 30 2.00 6.25
X X RLS300 30 0.50 2.31
Spreader Min. Clearance
(in.)
Max Spread
(in.)
Weight
(lbs.)
X X HS2000 0.56 4.00 4.80
Ordering Information
Values shown in short tons (2,000 lb). To convert to long tons, multiply by
0.893. To convert to metric tons, multiply by 0.907. *
THE RIGHT CHOICE FOR THOSE HIGHER TON
MAINTENANCE KIT NEEDS.
SK
SERIES
Mechanical Puller
Selection Optional 25 Ton Storage Cases Optional Cylinders
L
H
W
L
H
W
MB5 308435OR9
Order
No.
Description
MB5 Metal Box Construction, 32” (L) x 19” (W) x 14” (H)
308435OR9 Wooden Box Construction, 36” (L) x 17.5” (W) x 14” (H)
START UP KITS
TONNAGE RANGE: 25
179 powerteam.com
Jacks
Features
Mechanical Puller
Selection Optional Dead-end Seater Optional Cylinders
POST-TENSION AND STRESSING JACKS
TONNAGE RANGE: 20 & 30
Model Shown:
SJ2010, SJ3010
■ Ideally suited for work on slab-on-grade where dirt, heat
and high volume use take their toll.
■ Available in single or double-acting models.
■ Standard single-acting units have a 10” stroke.
■ Standard double-acting units have an 8.5\" stroke.
■ Service repair is simple and components are long
lasting and easily replaced.
■ 3\" detachable seater nose assembly easily replaced
with optional 6\" nose assembly.
■ The jack of choice for high-rise and elevated work,
thanks to fast return time and light weight.
■ All hydraulic fluid controls are internal for more efficient
and safer operation during tensioning and retraction.
Dead-end seaters for production work and field work
available on special order. (Part #400120)
ONE OF THE MOST DURABLE MONO-STRAND
JACKS IN THE INDUSTRY.
SJ
SERIES
Multi-strand post-tensioning application.
powerteam.com 180 JacksOrdering Information
Order
Number
Cap. Stroke Oil
Cap.
Strand
Dia.
Seater
Type
Int. Press.
at Cap.
Tons at
10,000 psi
Description Recommended
Pumps for this
Stressing Jack
Prod.
Wt.
(tons) (in.) (cu. in.) (in.) (in.) (in.) (lbs.)
SJ2010 20 10.00 45.2 0.375 - 0.50 Spring 8,948 22.4 Post-tension jack with spring, seater 0.50” strand. PE554P/PE604T 55.00
SJ2010P 20 10.00 45.2 0.375 - 0.50 Power* 8,948 22.4 Post-tension jack with power seater, 0.50” strand. PE554PT/PE604PT 55.00
SJ2010DA 20 8.50 53.0 0.375 - 0.50 Power* 6,500 31.4 Double-acting post-tension jack with power seater, 0.50” strand. PE554PT/PE604PT 42.00
SJ3010 30 10.00 63.6 0.375 - 0.60 Spring 9,549 31.4 Post-tension jack with spring seater, 0.60” strand. PE554P/PE604T 76.00
SJ3010P 30 10.00 63.6 0.375 - 0.60 Power* 9,549 31.4 Post-tension jack with power seater, 0.60” strand. PE554PT/PE604PT 76.00
SJ3010DA 30 8.50 67.6 0.375 - 0.60 Power* 7,554 39.7 Double-acting post-tension jack with power seater, 0.60” strand. PE554PT/PE604PT 52.00
STRESSING JACK ACCESSORIES AND HOSES
Used with
Stressing
Jack
3” 3” 6” 6” 3/8” Dia. 7/16” Dia. 1/2” 19/32” Replacement
Gripper
Handle #
Gripper
Retainer
Plate #
(2 used)
Nose
Piece #
Wedge
Seater #
Nose
Piece
Wedge
Seater #
Gripper
Set #
Gripper
Set #
Gripper
Set #
Gripper
Set #
SJ2010 252564 252562 252759 252763 252568 252761 252567 NA 252570 252565
SJ2010P 252564 252562 252759 252763 252568 252761 252567 NA 252570 252565
SJ2010DA 252543 252542 252760 252764 252650 252762 252555 NA 252556 252544
SJ3010 252564 252562 252759 252763 252568 252761 252567 252569 252570 252565
SJ3010P 252564 252562 252759 252763 252568 252761 252567 252569 252570 252565
SJ3010DA 253363 253361 253364 253362 253390 NA 253391 253365 252556 252544
POST-TENSION AND STRESSING JACKS
TONNAGE RANGE: 20 & 30
Technical Dimensions
Order No. A B C Wt.
(in.) (in.) (in.) (lbs.)
SJ2010 21.00 9.00 6.50 55.00
SJ2010 22.00 10.20 7.00 76.00
SJ3010 22.00 10.20 7.00 76.00
SJ3010P 22.00 13.20 7.00 76.00
SJ2010DA 18.50 7.50 6.50 42.00
SJ3010DA 18.50 8.50 6.50 52.00
WARNING
WARNING DANGER
B
WARNING
WARNING DANGER
C
A
SJ
SERIES
*Options with Power Seaters require an additional hose to connect the Power Seater to the valve.
181 powerteam.com
Jacks
INFO SECTION
WORKSHEET
powerteam.com 182 JacksINFO SECTION
WORKSHEET
183 powerteam.com
Jacks
INFO SECTION
WORKSHEET
powerteam.com 184 JacksINFO SECTION
WORKSHEET
HYDRAULIC & MECHANICAL TOOLS
SELECT FROM A WIDE RANGE OF HYDRAULIC &
MECHANICAL TOOLS TO COMPLETE YOUR SYSTEM
REQUIREMENTS
• Full range of torque wrenches, low clearance in-line drives
and pumps for your bolting applications.
• Specialty tools include nut splitters, spreaders, bead
breakers and pipe flange tools.
• Hydraulic clamps for those unique applications requiring
higher forces
• Hydraulic testers and accessories to monitor hydraulic
circuits
• Wide selection of mechanical tools, such as pliers, pry
bars, O-ring picks, thread chasers and more.
185
Section /
Series Page Description Page(s)
TWHC, TWLC,
TWSL
High Cycle Torque Wrench,
Low Clearance Torque Wrench,
SlimLine Torque Wrench
187-190
195-199
201-202
FCV Flow Control Valve 203
NRP Series Pneumatic Torque Tools 205-206
PE55 TWP Electric Hydraulic Torque Wrench Pump 206
RWP55 Air Hydraulic Torque Wrench Pump 207
HNS Hydraulic Nut Splitter 208
FLS Hydraulic Flange Spreader 209-210
HFS Pipe Flange, Hydraulic Spreader 211
HS Hydraulic Spreaders 212
CC Hydraulic C-Clamps & Accessories 213
HP35 Hydraulic Punches and Accessories 215-216
HT Hydraulic Testers and Accessories 217-219
PLIERS Retaining Ring Pliers (Internal & External) 220
HAND
TOOLS Wrenches, Pry Bars, Spanners & Jimmy Bars 221
SERVICE
TOOLS
Pipe Sealant, O-Ring Seal Picks, Thread Chaser,
and Magnetic Pick-Up 222
INDEX
TOOLS SERIES
186
187 powerteam.com
Tools
The TWSD50 is th perfect choice in this power generation
application.
Features
■ Designed for high cycle life (2-3x more than existing
technology)
■ Increased reliability provided by simple drive assembly
means less downtime
■ Corrosion resistant material for use in harsh
environments
■ Compact nose radius allows the tool to fit in tighter,
hard-to-reach spaces
■ Low weight, high strength design
■ Fast operation, long stroke and optimum flow
■ Multi-direction high flow swivel manifold
■ Fully-enclosed drive mechanism for operator safety
■ Swivel manifold internal relief valve prevents retract
side over-pressurization
■ Fine tooth pawl prevents tool ‘lock-on’
QUALITY MEANS LOWER COST OF OWNERSHIP
ENHANCED USABILITY:
DESIGNED WITH SAFETY IN MIND:
Model Shown:
TWHC3
SERIES
TW TORQUE WRENCH, HIGH CYCLE
MAX. TORQUE: 1,413-6,050 FT LBS AT 10,000 PSI
Mechanical Puller
Selection
HANDLES SOLD SEPARATELY Optional Cylinders
The tool’s designed long-stroke mechanism imparts
a minimum 30 degree nut rotation per stroke while
maintaining a tight and compact nose radius. This is
a clear advantage over the short stroke and back-up
pawl mechanisms of light alloy competitive models.
Fewer parts and reduced torsion in operation equals
reduced wear, maintenance and associated costs.
powerteam.com 188
Technical Dimensions
ToolsOrder
No.
Description Order
No.
Description Order
No.
Description
TWHC1 Wrench TWHC1H Wrench with Handle DFTAS000001 Handle for TWHC1
TWHC3 Wrench TWHC3H Wrench with Handle DFTAS000001 Handle for TWHC3
TWHC6 Wrench
TW
SERIES
TORQUE WRENCH, HIGH CYCLE
MAX TORQUE: 1,413-6,050 FT LBS AT 10,000 PSI
* Dimension I shows thread size (on both sides of the tool) for safety handle or lifting point. TWHC50 model available with lifting points only.
E
A
D
G
F
B
I*
C
H
Tool
Model
Min
Torque
Max
Torque
Square
Drive A B C D E F G H I
Prod.
Wt.
lb-ft lb-ft (in) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lb)
TWHC1 170 1,413 3/4 5.2 5.71 1.1 4.39 6.69 1.56 2.67 3.39 M6 x 1.0 6.2
TWHC3 376 3,136 1 6.5 6.83 1.44 5.1 7.78 2.09 3.3 4.14 M6 x 1.0 11.7
TWHC6 726 6,050 1 1/2 7.56 7.94 1.73 6.24 9.59 2.4 3.93 5.32 M8 x 1.25 19.4
Ordering Information
189 powerteam.com
Tools
TWHC EXTENDED REACTION ARM TWHC-ERA
SERIES
TW TORQUE WRENCH ACCESSORIES
EXTENDED REACTION ARM & HANDLE
TW HANDLE
■ Robust steel construction with ribbed polymer grip
■ Multi-position on tool for balanced handling
■ Cap-screw locking with positive ‘docking’
■ Is suitable for all wrench models (TWHC, TWSD,
TWLC). However, for larger sizes (TWSD25/TWLC 30/
TWHC50) we recommend the use of eye-bolt lifting.
Features
L3
L1
L2
(STD ARM)
(TWHC#-ERA1)
(TWHC#-ERA2)
(TWHC#-ERA3) L4 (STD ARM)
(TWHC#-ERA1)
(TWHC#-ERA2)
(TWHC#-ERA3)
Tool
Ref
Order
No.
L1 L2 L3 L4
(in.) (in.) (in.) (in.)
STD ARM 4.41 3.39 — —
TWHC1
TWHC1-ERA1 5.39 4.37
TWHC1-ERA2 6.38 5.35 2.36 1.18
TWHC1-ERA3 7.36 6.34
STD ARM 5.12 4.13 — —
TWHC3
TWHC3-ERA1 6.10 5.12
TWHC3-ERA2 7.09 6.10 2.76 1.38
TWHC3-ERA3 8.07 7.09
STD ARM 6.23 5.35 — —
TWHC6
TWHC6-ERA1 7.24 6.34
TWHC6-ERA2 8.23 7.32 3.74 1.57
TWHC6-ERA3 9.21 8.31
■ Long reach version of TWHC standard reaction arm
■ 3 standard sizes per model (0.98 in./1.97 in./2.95 in.),
specials upon request
■ Replaces standard reaction arm via quick release
locking pin
■ Steel alloy construction
■ 360° rotation
■ Available for full range of tool sizes
Features
Order No. Description Tool Ref
DFTAS000001 Wrench Handle
TWSD1
TWSD3
TWHC1
TWHC3
TWLC2
Order No. Description Tool Ref
DFTAS000002 Wrench Handle
TWSD6
TWSD11
TWHC6
TWLC4
TWLC8
TWLC15
Ordering Information
Ordering Information
powerteam.com 190 ToolsTWHC REACTION PAD TWHC-RP
TW
SERIES
TORQUE WRENCH ACCESSORIES
REACTION PAD & LONG REACTION ARM
Tool
Ref
Order
No.
L1 L2 L3 Width
(in.) (in.) (in.) (in.)
TWHC1 TWHC1-RP 2.835 4.567 1.93 2.52
TWHC3 TWHC3-RP 3.39 5.43 2.17 2.99
TWHC6 TWHC6-RP 3.90 6.38 2.44 3.50
■ In-Line Reaction Pad for TWHC wrenches used as
simple pad, or modified platform for specific application
(Machine-able/Weld-able platform)
■ Replaces standard reaction arm via quick release
locking pin
■ Steel alloy construction
■ 360° rotation
■ Available for full range of tool sizes
Features
L2
L1
L3
WIDTH
Ordering Information
TWHC LONG REACTION ARM TWHC-LRA
■ Tubular extension arm for TWHC wrenches for in-line
reaction outside wrench profile
■ Replaces standard reaction arm via quick release pin
locking
■ Steel/light alloy construction (reaction flat machined on
tube end)
■ Can be cut down to suit specific length
■ Available for full range of tool sizes
Features
Tool
Ref
Order
No.
L1 L2
(in.) (in.)
TWHC1 TWHC1-LRA
TWHC3 TWHC3-LRA 19.72 6.00
TWHC6 TWHC6-LRA
L1
L2
Ordering Information
191 powerteam.com
Tools
The TWHC11 is th perfect choice with a large reaction surface to eliminate
damage to the gears during the tightening process.
Model Shown:
TWHC20
TORQUE WRENCH, HIGH CYCLE
MAX TORQUE: 1,413-53,000 FT LBS AT 10,000 PSI
Tool
Model
Min.
Torque
Max.
Torque
Square
Drive A B C D E F G H I Wt.
lb-ft lb-ft (in) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (in.) (lb)
TWHC11 1336 11,134 1 1/2 9.09 9.18 2.07 7.34 11.81 3.39 5.12 8.16 M8 x 1.25 34.9
TWHC20 2439 20,325 2 1/2 11.01 12.21 2.52 8.65 14.34 3.68 6.10 8.35 M12 x 1.75 60.8
TWHC35 3890 32,418 2 1/2 13.40 13.61 3.05 9.90 16.73 4.74 7.15 8.97 M12 x 1.75 102
TWHC50 6360 53,000 2 1/2 15.93 14.04 3.46 10.49 17.58 4.53 7.57 10.16 M12 x 1.75 152
Order
No.
Description Order
No.
Description
TWHC11 Wrench TWHC35 Wrench
TWHC20 Wrench TWHC50 Wrench
SERIES
TW
Technical Dimensions
Ordering Information
■ Designed for high cycle life (2-3x more than existing
technology)
■ Increased reliability provided by simple drive assembly
means less downtime
■ Corrosion resistant material for use in harsh
environments
■ Compact nose radius allows the tool to fit in tighter,
hard-to-reach spaces
■ Low weight, high strength design
■ Fast operation, long stroke and optimum flow
■ Multi-direction high flow swivel manifold
■ Fully-enclosed drive mechanism for operator safety
■ Swivel manifold internal relief valve prevents retract
side over-pressurization
■ Fine tooth pawl prevents tool ‘lock-on’
QUALITY MEANS LOWER COST OF OWNERSHIP
ENHANCED USABILITY:
DESIGNED WITH SAFETY IN MIND:
Features
powerteam.com 192 ToolsNote: For Long Reach (Extended Length) sockets add “LR” to the end of the part number. For 12 point (bi-hex) sockets, add “BH” to the end
of the part number.
A
ACC.
TORQUE WRENCH,
SQUARE DRIVE & ACCESSORIES
Torque
Wrench
Hexagon
Drive Size
AF (in.)
Order No.
TWSD TWHC
(TWHC1)
0.63 TWD1-063 TWHCHD01-063
0.75 TWD1-075 TWHCHD01-075
0.88 TWD1-088 TWHCHD01-088
1.00 TWD1-100 TWHCHD01-100
(TWHC3)
0.63 TWD3-063 TWHCHD03-063
0.75 TWD3-075 TWHCHD03-075
0.88 TWD3-088 TWHCHD03-088
1.00 TWD3-100 TWHCHD03-100
1.13 TWD3-113 TWHCHD03-113
1.25 TWD3-125 TWHCHD03-125
1.38 TWD3-138 TWHCHD03-138
1.50 TWD3-150 TWHCHD03-150
1.63 TWD3-163 TWHCHD03-163
(TWHC6)
0.88 TWD6-063 TWHCHD06-063
0.75 TWD6-075 TWHCHD06-075
0.88 TWD6-088 TWHCHD06-088
1.00 TWD6-100 TWHCHD06-100
1.13 TWD6-113 TWHCHD06-113
Torque
Wrench
Hexagon
Drive Size
AF (in.)
Order No.
TWSD TWHC
(TWHC6)
1.25 TWD6-125 TWHCHD06-125
1.38 TWD6-138 TWHCHD06-138
1.50 TWD6-150 TWHCHD06-150
1.63 TWD6-163 TWHCHD06-163
(TWSD11)
1.13 TWD11-113 -
1.25 TWD11-125 -
1.38 TWD11-138 -
1.50 TWD11-150 -
1.63 TWD11-163 -
1.75 TWD11-175 -
(TWSD25)
1.50 TWD25-150 -
1.63 TWD25-163 -
1.75 TWD25-175 -
1.88 TWD25-188 -
2.00 TWD25-200 -
2.25 TWD25-225 -
2.50 TWD25-250 -
2.75 TWD25-275 -
SQUARE DRIVE - ADAPTERS & SOCKETS
SQUARE DRIVE - IMPACT SOCKETS
Socket
Size 0.75” Drive 1.00” Drive 1.50” Drive 2.50” Drive
(in.) Part No. Part No. Part No. Part No.
0.88 TWSIA088 TWSIB088 — —
1.06 TWSIA106 TWSIB106 — —
1.25 TWSIA125 TWSIB125 — —
1.38 TWSIA138 TWSIB138 — —
1.44 TWSIA144 TWSIB144 — —
1.63 TWSIA163 TWSIB163 TWSIC163 —
1.81 TWSIA181 TWSIB181 - —
2.00 TWSIA200 TWSIB200 TWSIC200 —
2.19 TWSIA219 TWSIB219 TWSIC219 —
2.38 TWSIA238 TWSIB238 TWSIC238 —
2.56 — TWSIB256 TWSIC256 —
2.75 — TWSIB275 TWSIC275 —
2.94 — TWSIB294 TWSIC294 —
Socket
Size 0.75” Drive 1.00” Drive 1.50” Drive 2.50” Drive
(in.) Part No. Part No. Part No. Part No.
3.13 — TWSIB313 TWSIC313 TWSIF313
3.38 — TWSIB338 TWSIC338 TWSIF338
3.50 — TWSIB350 TWSIC350 TWSIF350
3.75 — TWSIB375 TWSIC375 TWSIF375
3.88 — TWSIB388 — TWSIF388
4.13 — TWSIB413 TWSIC413 TWSIF413
4.25 — TWSIB425 TWSIC425 TWSIF425
4.63 — — TWSIC463 TWSIF463
5.00 — — — TWSIF500
5.38 — — — TWSIF538
5.75 — — — TWSIF575
6.13 — — — TWSIF613
Ordering Information
Ordering Information
193 powerteam.com
Tools
A
ACC.
TORQUE WRENCH,
HIGH CYCLE, ACCESSORIES
Features
L3
L1
L2
(STD ARM)
(TWSD#-ERA1)
(TWSD#-ERA2)
(TWSD#-ERA3) L4 (STD ARM) (TWSD#-ERA1) (TWSD#-ERA2) (TWSD#-ERA3)
TWHC EXTENDED REACTION ARM TWHC-ERA
Tool
Ref
Order
No.
L1 L2 L3 L4
(in.) (in.) (in.) (in.)
STD ARM 4.41 3.39
TWSD1
TWHC1-ERA1 5.39 4.37
TWHC1-ERA2 6.38 5.35 2.36 1.18
TWHC1-ERA3 7.36 6.34
STD ARM 4.88 4.13
TWSD3
TWHC3-ERA1 5.87 5.12
TWHC3-ERA2 6.85 6.10 2.76 1.38
TWHC-ERA3 7.83 7.09
STD ARM 5.59 5.35
TWSD6
TWHC6-ERA1 6.57 6.34
TWHC6-ERA2 7.56 7.32 3.74 1.57
TWHC6-ERA3 8.54 8.31
STD ARM 7.05 6.5
TWSD11
TWHC11-ERA1 8.03 7.48
TWHC11-ERA2 9.02 8.46 4.33 1.57
TWHC11-ERA3 10 9.45
■ Long reach version of TWHC standard reaction arm
■ 3 standard sizes per model (0.98 in./1.97 in./2.95 in.),
specials upon request
■ Replaces standard reaction arm via quick release
locking pin
■ Steel alloy construction
■ 360° rotation
■ Available for full range of tool sizes
Ordering Information
■ Robust steel construction with ribbed polymer grip
■ Multi-position on tool for balanced handling
■ Cap-screw locking with positive ‘docking’
■ Is suitable for all wrench models (TWHC, TWLC).
However, for larger sizes we recommend the use of
eye-bolt lifting.
Features
TW HANDLE
Order No. Description Tool Ref
DFTAS000001 Wrench Handle
TWHC1
TWHC3
TWLC2
Order No. Description Tool Ref
DFTAS000002 Wrench Handle
TWHC6
TWHC11
TWLC4
TWLC8
TWLC15
Ordering Information
powerteam.com 194 ToolsA
ACC.
TWHC LONG REACTION ARM TWHC-LRA
■ Tubular extension arm for TWHC wrenches for in-line
reaction outside wrench profile
■ Replaces standard reaction arm via quick release
locking pin
■ Steel/light alloy construction (reaction flat machined on
tube end)
■ Can be cut down to suit specific length
■ Available for full range of tool sizes
Features
Ordering Information
501.0 (19.72\")
152.0 (6.0\")
Tool
Ref
Order
No.
L1 L2
(in.) (in.)
TWHC11 TWHC11-LRA 19.72 6.00
■ Wrench In-Line Reaction Pad for TWHC wrenches
used as simple pad, or modified platform, for specific
application (Machine-able/Weld-able platform)
■ Replaces standard reaction arm via quick release
locking pin
■ Steel alloy construction
■ 360° rotation
■ Available for full range of tool sizes
Features
TWHC REACTION PAD TWSD-RP
L2
L1
L3
WIDTH
Tool
Ref
Order
No.
L1 L2 L3 Width
(in.) (in.) (in.) (in.)
TWHC11 TWHC11 4.311 7.264 2.579 4.133
Ordering Information
TORQUE WRENCH,
HIGH CYCLE, ACCESSORIES
195 powerteam.com
Tools
■ Corrosion resistant finish, low weight, high strength
steel body construction design with superior torsional
strength.
■ Fine tooth ratchet with floating piston design with small
nose radius, allows for a fast operation cycle.
■ Link pin does not fall out.
■ Multi-axis high flow swivel manifold with internal relief
valve prevents retract side over-pressurization
■ “Hardened” steel reaction pad on TWLC8, 15 & 30
■ Simple design, auto-connect drive piston quick
interchangeable heads, no tools necessary, consistent
torque output
■ Replaceable reaction pad on larger models
■ Power Team PowerThon™ Limited Lifetime Warranty
THE CLEARANCE TOOL FEATURES A LONG
NECK, SHORT HEIGHT, AND SMALL NOSE RADIUS
FOR INACCESSIBLE BOLTING AREAS FOUND IN
INDUSTRY.
Model Shown:
TWLC Body
Tool
Model
Hex Range Min.
Torque
Max.
Torque
Weight
(Body Only)
(in.) (ft. lbs.) (ft. lbs.) (lbs.)
TWLC2 1.25 - 2.38 189 1,575 2.2
TWLC4 1.50 - 3.13 477 3,975 4.4
TWLC8 2.38 - 3.88 954 7,950 7.7
TWLC15 2.56 - 4.63 1,782 14,850 15.4
TWLC30 3.13 - 6.13 3,456 28,800 31.9
TORQUE WRENCH, LOW CLEARANCE
MAX. TORQUE: 28,800 FT. LBS. AT 10,000 PSI
* Links sold separately.
Tool is not shipped with link.
Mechanical Puller
Selection Optional Cylinders Torque Wrench Hoses - Non-Conductive
Dual Line
Order
No.
Hose
Length
Hose
I.D.
(ft.) (in.)
TWH15 15 1/4\"
TWH20 20 1/4\"
TWH30 50 1/4\"
I
G
H
J
A
B
E
C
F
D
Body
Order
No.
A B C D E F G H
(in.) (in.) (in.) (in.) (in.) (deg.) (in.) (in.)
TWLC2 5.4 4.1 5.0 0.3 1.4 13 1.3 1.7
TWLC4 6.4 5.1 6.3 0.4 1.7 13 1.7 2.0
TWLC8 7.7 6.2 7.0 1.0 1.6 14 2.1 2.6
TWLC15 8.8 7.3 7.9 1.1 1.7 14 2.5 3.0
TWLC30 10.9 9.4 10.5 1.0 2.4 15 3.2 3.7
SERIES
TW
Technical Dimensions Ordering Information
Mechanical Puller
Selection Handle Options Optional Cylinders
TWLC2 + DFTAS000001
TWLC4 + DFTAS000002
TWLC8
TWLC15
Handle can be mounted to either Link or Drive Body.
TWLC4 only- use adaptor DFTHA000003 to mount
handle to drive body
Features
powerteam.com 196 ToolsTORQUE WRENCH, LOW CLEARANCE REDUCERS - TWLC
DRIVE BODY, LINKS & REDUCERS
LOW CLEARANCE - REDUCERS
Body Link Nut A/F Reducer Reducer Reducer Reducer Reducer Reducer
Order No. Part No. (in.) (in.) Part No. (in.) Part No. (in.) Part No.
TWLC2
TWL2-032 1.25 — — — — — —
TWL2-036 1.44 — — — — — —
TWL2-041 1.63 1.63 - 1.44 TWR2-041036 1.63 - 1.25 TWR2-041032 — —
TWL2-046 1.81 1.81 - 1.63 TWR2-046041 1.81 - 1.44 TWR2-046036 1.81 - 1.25 TWR-046032
TWL2-050 2.00 2.00 - 1.81 TWR2-050046 2.00 - 1.63 TWR2-050041 2.00 - 1.44 TWR2-050036
TWL2-055 2.19 2.19 - 2.00 TWR2-055050 2.19 - 1.81 TWR2-055046 2.19 - 1.63 TWR2-055041
TWL2-060 2.38 2.38 - 2.19 TWR2-060055 2.38 - 2.00 TWR2-060050 2.38 - 1.81 TWR2-060046
TWLC4
TWL4-041 1.63 1.63 - 1.44 TWR4-041036 1.63 - 1.25 TWR4-041032 — —
TWL4-046 1.81 1.81 - 1.63 TWR4-046041 1.81 - 1.44 TWR4-046036 1.81 - 1.25 TWR4-046032
TWL4-050 2.00 2.00 - 1.81 TWR4-050046 2.00 - 1.63 TWR4-050041 2.00 - 1.44 TWR4-050036
TWL4-055 2.19 2.19 - 2.00 TWR4-055050 2.19 - 1.81 TWR4-055046 2.19 - 1.63 TWR4-055041
TWL4-060 2.38 2.38 - 2.19 TWR4-060055 2.38 - 2.00 TWR4-060050 2.38 - 1.81 TWR4-060046
TWL4-065 2.56 2.56 - 2.38 TWR4-065060 2.56 - 2.19 TWR4-065055 2.56 - 2.00 TWR4-065050
TWL4-070 2.75 2.75 - 2.56 TWR4-070065 2.75 - 2.38 TWR4-070060 2.75 - 2.19 TWR4-070055
TWL4-075 2.94 2.94 - 2.75 TWR4-075070 2.94 - 2.56 TWR4-075065 2.94 - 2.38 TWR4-075060
TWL4-080 3.13 3.13 - 2.94 TWR4-080075 3.13 - 2.75 TWR4-080070 3.13 - 2.56 TWR4-080065
TWLC8
TWL8-060 2.38 2.38 - 2.19 TWR8-060055 2.38 - 2.00 TWR8-060050 2.38 - 1.81 TWR8-060046
TWL8-065 2.56 2.56 - 2.38 TWR8-065060 2.56 - 2.19 TWR8-065055 2.56 - 2.00 TWR8-065050
TWL8-070 2.75 2.75 - 2.56 TWR8-070065 2.75 - 2.38 TWR8-070060 2.75 - 2.19 TWR8-070055
TWL8-075 2.94 2.94 - 2.75 TWR8-075070 2.94 - 2.56 TWR8-075065 2.94 - 2.38 TWR8-075060
TWL8-080 3.13 3.13 - 2.94 TWR8-080075 3.13 - 2.75 TWR8-080070 3.13 - 2.56 TWR8-080065
TWL8-085 3.38 3.38 - 3.13 TWR8-085080 3.38 - 2.94 TWR8-085075 3.38 - 2.75 TWR8-085070
TWL8-090 3.50 3.50 - 3.38 TWR8-090085 3.50 - 3.13 TWR8-090080 3.50 - 2.94 TWR8-090075
TWL8-095 3.75 3.75 - 3.50 TWR8-095090 3.75 - 3.38 TWR8-095085 3.75 - 3.13 TWR8-095080
TWL8-100 3.88 3.88 - 3.75 TWR8-100095 3.88 - 3.50 TWR8-100090 3.88 - 3.38 TWR8-100085
TWLC15
TWL15-070 2.75 2.75 - 2.56 TWR15-070065 2.75 - 2.38 TWR15-070060 2.75 - 2.19 TWR15-070055
TWL15-075 2.94 2.94 - 2.75 TWR15-075070 2.94 - 2.56 TWR15-075065 2.94 - 2.38 TWR15-075060
TWL15-080 3.13 3.13 - 2.94 TWR15-080075 3.13 - 2.75 TWR15-080070 3.13 - 2.56 TWR15-080065
TWL15-085 3.38 3.38 - 3.13 TWR15-085080 3.38 - 2.94 TWR15-085075 3.38 - 2.75 TWR15-085070
TWL15-090 3.50 3.50 - 3.38 TWR15-090085 3.50 - 3.13 TWR15-090080 3.50 - 2.94 TWR15-090075
TWL15-095 3.75 3.75 - 3.50 TWR15-095090 3.75 - 3.38 TWR15-095085 3.75 - 3.13 TWR15-095080
TWL15-100 3.88 3.88 - 3.75 TWR15-100095 3.88 - 3.50 TWR15-100090 3.88 - 3.38 TWR15-100085
TWL15-105 — — — — — — —
TWL15-425 4.25 4.25 - 3.88 TWR15-425388 4.25 - 3.75 TWR15-425375 4.25 - 3.50 TWR15-425350
TWL15-110 — — — — — — —
TWL15-115 — — — — — — —
TWL15-463 4.63 4.63 - 4.25 TWR15-463425 4.63 - 3.88 TWR15-463388 4.63 - 3.75 TWR15-463375
TWLC30
TWL30-080 3.13 3.13 - 2.94 TWR30-080075 3.13 - 2.75 TWR30-080070 3.13 - 2.56 TWR30-080065
TWL30-085 3.38 3.38 - 3.13 TWR30-085080 3.38 - 2.94 TWR30-085075 3.38 - 2.75 TWR30-085070
TWL30-090 3.50 3.50 - 3.38 TWR30-090085 3.50 - 3.13 TWR30-090080 3.50 - 2.94 TWR30-090075
TWL30-095 3.75 3.75 - 3.50 TWR30-095090 3.75 - 3.38 TWR30-095085 3.75 - 3.13 TWR30-095080
TWL30-100 3.88 3.88 - 3.75 TWR30-100095 3.88 - 3.50 TWR30-100090 3.88 - 3.38 TWR30-100085
TWL30-105 — — TWR30-105100 — TWR30-105095 — TWR30-105090
TWL30-425 4.25 4.25 - 3.88 TWR30-425388 4.25 - 3.75 TWR30-425375 4.25 - 3.50 TWR30-425350
TWL30-110 — — — — — — —
TWL30-115 — — — — — — —
TWL30-463 4.63 4.63 - 4.25 TWR30-463425 4.63 - 3.88 TWR30-463388 4.63 - 3.75 TWR30-463375
TWL30-120 — — — — — — —
TWL30-500 5.00 5.00 - 4.63 TWR30-500463 5.00 - 4.25 TWR30-500425 5.00 - 3.88 TWR30-500388
TWL30-130 — — — — — — —
TWL30-135 5.38 5.38 - 5.00 TWR30-135125 5.38 - 4.63 TWR30-135120 5.38 - 4.25 TWR30-135115
TWL30-145 5.75
TWL30-150 — AVAILABLE UPON REQUEST
TWL30-155 6.13
Special sizes available upon request.
TW
SERIES
197 powerteam.com
Tools
Nut A/F TWLC2 TWLC4 TWLC8
Link
Order
No.
Radius
R I J Weight
(Link Only)
Link
Order
No.
Radius
R I J Weight
(Link Only)
Link
Order
No.
Radius
R I J Weight
(Link Only)
(in.) (in.) (in.) (in.) (lbs.) (in.) (in.) (in.) (lbs.) (in.) (in.) (in.) (lbs.)
1.13 TWL2-026
1.24 7.09 1.50 4.41
- -
1.06 TWL2-027 - -
1.13 TWL2-029 - -
1.19 TWL2-030 - -
1.25 TWL2-032 - -
1.31 TWL2-033 TWL4-033
1.44 8.94 2.09 8.82
-
1.38 TWL2-035 TWL4-035 -
1.44 TWL2-036 TWL4-036 -
1.50 TWL2-150
1.36 7.13 1.57 4.41
TWL4-150 -
1.56 TWL2-040 TWL4-040 -
1.63 TWL2-041 TWL4-041 -
1.69 TWL2-043
1.46 7.20 1.57 4.41
TWL4-043
1.54 8.94 2.09 8.82
-
1.75 TWL2-044 TWL4-044 -
1.81 TWL2-046 TWL4-046 -
1.88 TWL2-188
1.57 7.28 1.69 4.41
TWL4-188
1.65 8.94 2.09 8.82
TWL8-188
1.99 10.79 3.03 15.43
1.94 TWL2-049 TWL4-049 TWL8-049
2.00 TWL2-050 TWL4-050 TWL8-050
2.06 TWL2-052
1.67 7.28 1.69 4.41
TWL4-052
1.75 8.94 2.09 8.82
TWL8-052
2.13 TWL2-054 TWL4-054 TWL8-054
2.19 TWL2-055 TWL4-055 TWL8-055
2.25 TWL2-057
1.79 7.28 1.69 4.41
TWL4-225
1.87 8.94 2.09 8.82
TWL8-057
2.31 TWL2-059 TWL4-059 TWL8-059
2.38 TWL2-060 TWL4-060 TWL8-060
2.44 - TWL4-062
1.97 8.94 2.09 8.82
TWL8-062
2.50 - TWL4-063 TWL8-063 2.09 10.79 3.03 16.53
2.56 - TWL4-065 TWL8-065
2.63 - TWL4-067
2.09 9.02 2.20 8.82
TWL8-067
2.69 - TWL4-068 TWL8-068 2.20 10.79 3.03 16.53
2.75 - TWL4-070 TWL8-070
2.81 - TWL4-071
2.19 9.02 2.20 9.92
TWL8-071
2.88 - TWL4-073 TWL8-073 2.30 10.79 3.03 16.53
2.94 - TWL4-075 TWL8-075
3.00 - TWL4-077
2.32 9.06 2.28 9.92
TWL8-077
306 - TWL4-313 TWL8-313 2.44 10.91 2.83 17.64
3.13 - TWL4-080 TWL8-080
3.19 - - TWL8-081
2.64 10.91 2.83 17.64
3.25 - - TWL8-083
3.31 - - TWL8-084
3.38 - - TWL8-085
3.44 - - TWL8-087
- - TWL8-089
3.50 - - TWL8-090
3.56 - - TWL8-091
2.89 10.91 2.83 7.64
3.63 - - TWL8-092
3.69 - - TWL8-094
3.75 - - TWL8-095
3.81 - - TWL8-097
- - TWL8-388
3.88 - - TWL8-100
NOTE:
The sizes listed on these pages encompass both heavy hex and standard hex nut sizes.
Check your local SPX FLOW Power Team Office for availability as some items may be special order.
TORQUE WRENCH, LOW CLEARANCE LINKS - TWLC
PARTS NUMBERS, NOSE RADIUS
R
SERIES
TW
powerteam.com 198 ToolsNut A/F TWLC15 TWLC30
Link
Order
No.
Radius
R I J Weight
(Link Only)
Link
Order
No.
Radius
R I J Weight
(Link Only)
(in.) (in.) (in.) (in.) (lbs.) (in.) (in.) (in.) (lbs.)
2.44 TWL15-062
2.38 12.32 3.46 27.56
-
2.50 TWL15-063 -
2.56 TWL15-065 -
2.63 TWL15-067 -
2.69 TWL15-068 -
2.75 TWL15-070 -
2.81 TWL15-071
2.48 12.32 3.46 27.56
-
2.88 TWL15-073 -
2.94 TWL15-075 -
3.00 TWL15-077
2.62 12.32 3.46 28.66
-
3.06 TWL15-313 -
3.13 TWL15-080 TWL30-080
3.03 15.47 4.09 58.42
3.19 TWL15-081
2.83 12.32 3.46 29.76
TWL30-081
3.25 TWL15-083 TWL30-083
3.31 TWL15-084 TWL30-084
3.38 TWL15-085 TWL30-085
3.44 TWL15-087 TWL30-087
TWL15-089 TWL30-089
3.50 TWL15-090 TWL30-090
3.56 TWL15-091
3.07 12.44 3.15 29.76
TWL30-091
3.27 15.47 4.09 58.42
3.63 TWL15-092 TWL30-092
3.69 TWL15-094 TWL30-094
3.75 TWL15-095 TWL30-095
3.81 TWL15-097 TWL30-097
TWL15-388 TWL30-388
3.88 TWL15-100 TWL30-100
4.00 TWL15-102
3.25 12.44 3.15 30.86
TWL30-102
3.50 15.47 4.09 60.63
4.06 TWL15-103 TWL30-103
4.13 TWL15-105 TWL30-105
4.19 TWL15-106 TWL30-106
4.25 TWL15-425 TWL30-425
4.31 TWL15-110
3.44 12.44 3.15 30.86
TWL30-110
4.38 TWL15-111 TWL30-111
3.62 15.47 4.09 60.63
4.44 TWL15-113 TWL30-113
4.50 TWL15-114 TWL30-114
TWL15-115 TWL30-115
4.56 TWL15-116 TWL30-116
4.63 TWL15-463 TWL30-463
4.69 - TWL30-119 3.90 15.75 4.29 62.83 4.75 - TWL30-120
Nut
A/F TWLC30 (Continued)
Link
Order
No.
Radius
R I J Weight
(Link Only)
(in.) (in.) (in.) (in.) (lbs.)
4.81 TWL30-122
3.90 15.75 4.29 62.83
TWL30-123
4.88 TWL30-124
4.94 TWL30-125
5.00 TWL30-500
5.06 TWL30-129
4.13 15.75 4.29 62.83
5.13 TWL30-130
5.19 TWL30-132
5.25 TWL30-133
5.38 TWL30-135
TWL30-538
5.44 TWL30-138
4.33 15.75 4.29 62.83
5.50 TWL30-140
5.56 TWL30-141
5.63 TWL30-143
5.69 TWL30-144
5.75 TWL30-145
TWL30-146
5.81 TWL30-148
4.57 15.75 4.29 65.04
5.88 TWL30-149
TWL30-150
5.94 TWL30-151
6.00 TWL30-152
6.06 TWL30-154
6.13 TWL30-155
TO SPECIFY A TWLC SOLUTION:
1. Find a link for your application (nut size)
2. Choose the appropriate drive body
3. Add reducers for additional nut sizes
R
Please order Drive Body and Link separately and pay attention to the same size, for Example TWLC2
and TWL2-041.
NOTE:
TW
SERIES
TORQUE WRENCH, LOW CLEARANCE LINKS - TWLC
PARTS CODES, NOSE RADIUS
199 powerteam.com
Tools
A
ACC.
TORQUE WRENCH,
LOW CLEARANCE ACCESSORIES
Features
TWLC REACTION BAR TWLC-RB
■ In-Line Extension Reaction Bar for TWLC wrenches
allows extended reach on the same plane
■ Pin engagement, no tools required
■ Available for full range of tool sizes
L1
L2
L3
Tool
Ref
Order
No.
L1 L2 L3
(in.) (in.) (in.)
TWLC2 TWLC2-RB 15.00 1.10 2.17
TWLC4 TWLC4-RB 18.00 1.38 2.60
TWLC8 TWLC8-RB 18.00 1.46 3.35
TWLC15 TWLC15-RB 20.00 1.57 4.01
TWLC30 TWLC30-RB 20.00 1.38 5.00
Mechanical Puller
Selection Reaction Accessories Optional Cylinders
Power Team offers a varied range of alternative and
optional reaction accessories which help to find a
reaction point solution no matter how unusual the
bolted application is.
Ordering Information
TWLC REACTION PADDLE TWLC-RP
L4
L3 L2
L1
Tool
Ref
Order
No.
L1 L2 L3 L4
(in.) (in.) (in.) (in.)
TWLC2 TWLC2-RP 3.31 1.38 5.59 0.51
TWLC4 TWLC4-RP 4.29 1.81 7.01 0.75
TWLC8 TWLC8-RP 5.37 2.25 8.66 1.02
TWLC15 TWLC15-RP 6.50 2.76 9.92 1.77
TWLC30 TWLC30-RP 7.874 3.39 12.48 1.73
Ordering Information
■ Off-Set Reaction Arm for TWLC wrenches allows
off-set reaction within wrench profile
■ Pin engagement, no tools required
■ Light alloy construction
■ Available for full range of tool
Features
powerteam.com 200 ToolsCUSTOM REACTION PADS AND REDUCERS ARE AVAILABLE.
Contact SPX FLOW, or an authorized Power Team distributor, for more details!
HAVE A UNIQUE APPLICATION?
DOES STANDARD PRODUCT NOT FIT?
201 powerteam.com
Tools
SLIMLINE TORQUE WRENCHES
MAX. TORQUE: 4,210 FT. LBS. AT 10,000 PSI
Model Shown:
TWSL4-046 Link (left) & TWSL4-060
Link with TWLC4 Drive Body (right)
■ Dynamic engineering modeling (Finite Element Analysis
and optimized tool design to extend life and durability).
■ The SlimLine links use the same quick change Drive
Body as the existing TWLC links
■ Small nose radius, fits all standard API and ANSI
flanges.
■ Rigid steel body construction with corrosion resistant
plating.
■ Fully-enclosed drive mechanism for operator safety.
■ Swivel manifold has an internal relief valve to prevent
retract side over-pressurization.
■ Multi-axis swivel technology for free positioning of tool
and hoses.
Mechanical Puller
Selection Optional Cylinders Drive Body interchanges with the
TWLC & TWSL link sizes
The Drive Body is designed to interchange with the
TWLC (Low Clearance) and the new TWSL (SlimLine)
Links, lowering your tool investment across each
series to broaden your application reach.
Handle can be mounted to either Link or Drive Body.
TWLC4 only - use adaptor DFTHA000003 to mount
handle to drive body
Drive Body
TWSL Series
TWLC Series
Optional Handle
Order #: DFTAS000001 for TWSL2
DFTAS000002 for TWSL4
SERIES
TW
Pumps Hoses Tools
*TWSL4-046 DIMENSION 9.91mm
SIZE HEX RANGE A
(mm)
B
(mm)
C
(mm)
D
(mm)
E
(mm)
F
(mm)
G
(mm)
MIN TORQUE
lb-ft (Nm)
MAX TORQUE
lb-ft (Nm)
TWSL4 1 11/16\" - 3 1/8\" 43 - 80 mm 168.1 137.0 168.0 224.3 10.72* 30.5 52.0 505 (685) 2639 - 4210 (3578 - 5708)
D
A
HEX RANGE E
C
B
F
G
G
F F
C
F
A
F
B
F
E
F
D
HEX RANGE
Order
No. A B C D E F G
(in.) (in.) (in.) (in.) (in.) (in.) (in.)
TWSL2 5.71 4.49 5.04 7.26 0.35 0.98 1.65
TWSL4 6.61 5.39 6.61 8.83 0.42 1.20 2.04
ENGINEERED TO FIT INACCESSIBLE APPLICATIONS
WITH MINIMAL CLEARANCE.
Technical Dimensions
Mechanical Puller
Selection
Other Related Items Optional Cylinders
Contact your nearest Power Team sales representative for
assistance in sizing the proper tool for your application, or go to
powerteam.com website for details about other available link sizes
not listed.
Features
