电机型号Motormodel

RGW110-A3-40

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1,in the standard linear motormodule operation process,the platform willbe subjected togreaterimpact,so the installation platform needstohave sufficient stiffness and stability If the instllation platform stiffnessf it is insufficient, the standardmodule ill appear jiter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not less than0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW110-A1-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{^{.}}0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in the standard linearmotormodule operation process,the platform will be subjected to greaterimpact, so the installation platformneedstohave sufficientstiffnessandstability.f theinstallationplatformstiffnesslf it isinsufficient,thestandardmodulewillappearjiterandresonance during operation,which will affect thepositioning accuracy,repetition accuracyandequipment.

2.If conditions permit,the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan 0.02mm/500mm

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW110-A2-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 *0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in the standard linearmotormodule operationprocess,the platform will be subjected to greaterimpact, so theinstallation plaformneedstohave sufficient stiffnessandstability.f theinstallationplatformstiffnesslf it isinsufficientthestandardmodulewillappearjiterandresonance during operation,which will affect thepositioning accuracy,repetitionaccuracy and equipment.

2. If condlitions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the number of lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan 0.02\mathsf{mm}/500\mathsf{mm}

4, clean the table to ensure that the installation table is free of foreign bodies,burrs and otheritems that mayhinderthe installation.

尺寸示意图

电机型号Motormodel

RGW110-A3-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1, in the standard linear motor module operation process,the platform willbe subjected to greater impact, so the installation platform needs to have sufficient stiffness and stability If the installtion platform stiffnessf it is insufficient, the standardmodule willappear jiter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2. If condlitions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

Ire that theinstallation tableisfree of foreignbodies,burrs andotheritems thatmayhinde

尺寸示意图

电机型号Motormodel

RGW140-A1-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{0}.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1, in the standard linear motormodule operation process,the platform willbe subjected to greaterimpact,so theinstallation platform needsto have sufficient stiffness and stability. f the installation platform stiffnesf it is insufficient,the standard module willappear jitter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as wellas the numberoflockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not less than 0.02mm/500mm.

4, cleanthe table to ensure that the installation table is free of foreign bodies,burrs and otheritems that mayhinderthe installation.

尺寸示意图

电机型号Motormodel

RGW140-A2-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 ^{-0.02\mathsf{mm}/500\mathsf{mm}}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in the standard linearmotormodule operationprocess,the platform will be subjected to greaterimpact so the installation platformneedstohave sufficientstiffnessandstabilityf theinstallationplatformstiffnesslf it isinsufficient,thestandardmodulewillappearjitterandresonance during operation,which will affecthepositioning accuracy,repetitionaccuracyandequipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible,as wellas the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4,cleanthe tableto ensure that theinstallation table is free offoreignbodies,burrs andotheritems thatmayhindertheinstallation.

尺寸示意图

电机型号Motormodel

RGW140-A3-50

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1,in the standard linear motormodule operation process,the platform willbe subjected togreaterimpact,so the installation platform needstohave sufficient stiffness and stability If the instllation platform stiffnessf it is insufficient, the standardmodule ill appear jiter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not less than0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW140-A1-75

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm} ®
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.inthe standard linearmotormodule operationprocess,theplatform willbe subjectedtogreaterimpact,so theinstallationplatformneedstohave sufficient stiffness and stability.f the installtionplatform stiffnessf it is insufficient, thestandard module will appear jitter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motor model

RGW140-A2-75

注明：行程进制为40，N表示增加的行程段数，80为基准。如：L120模组N=（120-80）/40=1 Note:Thetravelscaleis40,Nrepresentsthenumberofadditional travelsegmentsand80isthebasis.Forexamplemodule120N=(120-80)/0=1

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02mm/500mm
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linear motormodule operation process,the platform willbe subjectedto greaterimpact,so the installation platform needsto have sufficient stiffness and stability.If the installation platform stiffnesslfit is insufficient,the standard module illappear jiter and resonance during operation,whichwill affect thepositioning accuracy,repetition accuracy and equipment.

2. If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

re that theinstallation tableisfreeofforeignbodies,burrsand otheritemsthatmayhinde

尺寸示意图

Dimensional diagram

电机型号Motormodel

RGW140-A3-75

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.inthe standard linearmotormodule operationprocess,theplatform willbe subjectedtogreaterimpact,so theinstallationplatformneedstohave sufficient stiffness and stability.f the installtionplatform stiffnessf it is insufficient, thestandard module will appear jitter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW170-A1-75

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1,in the standard linearmotormoduleoperation process,the platform willbe subjectedto greaterimpactso theinstallation platformneedstohave sufficient stiffnessandstability.f theinstallation platform stiffnesslf it isinsufficient,thestandard module willappear jitterandresonance during operation, which willaffect the positioning accuracy,repetition accuracy and equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the number of lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

尺寸示意图

Dimensional diagram

电机型号Motor model

RGW170-A2-75

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 *0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormodule operation proces,the platformwill be subjected togreaterimpact so the installation platformneedstohave sufficient stiffnessandstability.lf the installationplatformstiffnesslf it isinsufficient,the standardmodule willappearjitterandresonance during operation,which willaffecthe positioning accuracy,repetition accuracyand equipment.

2.If conditions permit,the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW170-A3-75

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.inthe standard linearmotormodule operationprocess,theplatform willbe subjectedtogreaterimpact,so theinstallationplatformneedstohave sufficient stiffness and stability.f the installtionplatform stiffnessf it is insufficient, thestandard module will appear jitter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号 MotormodelRGW170-A1-100

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 *0.02\mathsf{mm}/500\mathsf{mm},
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1, in the standard linear motor module operation process,theplatform will be subjected to greaterimpact,so the installation platform needsto have sufficient stiffnessandstability.f theinstallationplatform stiffnesslf it isinsufficient,the standardmodulewillappearjitterandresonance during operation, which willaffect the positioning accuracy,.repetition accuracy and equipment.

2. If condlitions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the number of lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not less than 0.02mm/500mm

lat the installation table is free of foreign bodies, burrs and other items that may hinder the

尺寸示意图

电机型号Motormodel

RGW170-A2-100

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{0}.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormodule operation process,the platform will be subjected to greaterimpact,so the installation platform needs tohave sufficient stiffness and stability. f the installation platform stiffnessif it is insufficient,the standard module will appear jiter and resonance during operation,which willaffecthepositioning accuracy,repetition accuracyand equipment.

2.If conditions permit,the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号

安装要求

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{0}.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1,in the standard linear motormodule operation process,the platform willbe subjected to greaterimpact,so theinstallation platform needstohave sufficient stiffness and stability. If the installtion platform stiffnessf it is insufficient, the standardmodule willappear jiter and resonance during operation, which willaffecthe positioning acuracy,repetition accuracy and equipment.

2. If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the number of lock screws.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be no1 lesthan0.02mm/500mm.

at the installation table is free of foreign bodies,burrs and other items that may hinder thei

尺寸示意图

电机型号Motormodel

RGW210-A1-100

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 *0.02\mathsf{mm}/500\mathsf{mm} ®
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in thestandard linearmotormodule operationprocess,the platformwill be subjected to greaterimpact,so theinstallation plaformneedstohave sufficient stiffnessandstability.If theinstallationplatformstiffnessfit isinsufficient,the standardmodule willappearjitterandresonance during operation, which willaffecthe positioning accuracy,repetition accuracy and equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as wellas the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW210-A2-100

安装要求

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1, in the standard linear motormodule operation process,the platform willbe subjected to greaterimpact,so the installation platform needsto have sufficient stiffness and stability If the installtion platform stiffnessf it is insufficient, the standardmodule willappear jiter and resonance during operation,which willaffect thepositioning accuracy,repetition accuracy and equipment.

2. If condlitions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan 0.02mm/500mm

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW210-A3-100

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in thestandard linearmotormodule operationprocess,the platform willbe subjected to greater impactso the installtion platformneedstohave sufficient stiffnessandstability.If the installationplatform stiffnesslf it isinsufficientthestandard modulewillappearjitterandresonance during operation,which willaffecthe positioning accuracy,repetition accuracy and equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW210-A1-125

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 *0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormodule operation process,the platform willbe subjected to greaterimpact,so theinstallation platform needstohave sufficient stiffnessandstability.f theinstallationplatformstiffnesslf it isinsufficient,thestandardmodulewillappearjitterandresonanceduring operation,which will affect thepositioning accuracy,repetition accuracyandequipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as wellas the number of lock screws.

3,the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

尺寸示意图

电机型号Motormodel

RGW210-A2-125

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{^{0}}.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormoduleoperation process,the platform willbe subjected to greaterimpact,so theinstallationplatformneedstohave sufficient stiffness and stability.If the installation plaform stiffnesslf it is insufficient,the standardmodule willappear jiter and resonance during operation,which will affect thepositioning accuracy,repetition accuracyandequipment.

2. If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not less than 0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW210-A3-125

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in the standard linearmotormodule operationprocess,the platform wilbe subjected to greater impactso theinstalltion platform needstohave sufficient stiffnessandstability.If theinstallationplatform stiffnesslf it isinsufficient,thestandardmodule willappearjitterandresonance during operation, which willaffect the positioning accuracy,.repetition accuracy and equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

电机型号Motormodel

RGW135B-A1-40

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \dot{^{0}}.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormodule operationprocess,the platform will be subjected to greaterimpact, so theinstallation platformneedstohave sufficientstiffnessandstability.f theinstallationplatformstiffnesslf it isinsufficientthestandardmodulewillappearjiterandresonance during operation,which will affecthepositioning accuracy,repetitionaccuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as wellas the numberoflockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm and the occasion with high accuracy requirements needs to be not less than 0.02mm/500mm.

4, cleanthe table to ensure that the installation table is free of foreign bodies,burrs and otheritems that mayhinderthe installation.

尺寸示意图

电机型号Motormodel

RGW135B-A2-40

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 0.02\mathsf{mm}/500\mathsf{mm}
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1. in the standard linearmotormoduleoperation process,the platform wilbe subjected to greaterimpact so the installation plaformneedstohave sufficient stiffnessandstability.If theinstallationplatformstiffnesslf it isinsufficient,thestandardmodule willappearjitter andresonance during operation, which willaffect the positioning accuracy,repetition accuracyand equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图

Dimensional diagram

电机型号Motormodel

RGW135B-A3-40

安装要求

Installation requirements

1、在标准直线电机模组运行过程中，平台会受到较大的冲击力，因此安装平台需要具备足够的刚度与稳定性。若安装平台刚度
不足，则标准模组在运行过程中会出现抖动、共振等现象，从而产生对定位精度、重复精度以及设备的影响。
2、在条件允许的情况下，应尽可能多的增加模组底座与安装台面的接触面积，以及锁螺钉的数量。
3、安装平台的台面平整度不低于 0.05\mathsf{mm}/500\mathsf{mm} ，对于精度要求高的场合需不低于 \left.0.02\mathsf{mm}/500\mathsf{mm}\right.
4、清理台面，确保安装台面无异物、毛刺等可能妨碍安装的物品。

1.in the standard linearmotormodule operation process,theplatform willbe subjectedtogreaterimpact so the installation platformneedstohave sufficient stiffnessandstability.If theinstallationplatform stiffnesslf it isinsufficient,the standardmodule willappearjitter andresonance during operation, which willaffect the positioning accuracy,repetition accuracy and equipment.

2.If conditions permit, the contact area between the module base and the installation table should be increased as much as possible, as well as the numberof lockscrews.

3, the tabletop flatness of the installation platform is not less than 0.05mm/500mm, and the occasion with high accuracy requirements needs to be not lessthan0.02mm/500mm.

4, clean the table to ensure that the installation table is free of foreign bodies, burrs and other items that may hinder the installation.

尺寸示意图